Utilitech 148008 Instrucciones de operación

Marca: Utilitech

Modelo: 148008

Tipo: Instrucciones de operación

BOOSTER UTILITY PUMP

ITEM #0955585

MODEL #148008

Español p. 12

Serial Number

Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-866-994-4148, 7:30 a.m. - 5:00 p.m., EST, Monday - Friday.

ATTACH YOUR RECEIPT HERE

AB171106

SW1116 B

Validation #LBWU-002234874.

PACKAGE CONTENTS

SAFETY INFORMATION

PART DESCRIPTION QUANTITY

A Pump 1

B Garden Hose Adapters 2

Please read and understand this entire manual before attempting to assemble, operate, or install the

product.

NOTE: Pumps with the “UL” Mark and pumps with the “US” mark are tested to UL Standard UL778.

CSA certied pumps are certied to CSA Standard C22.2 No. 108. (CUS.)

DANGER

• ELECTRICAL SHOCK HAZARD.

This pump is non-submersible. Keep the motor dry at all times. Do not wash the motor. Do not

submerse the pump in water. Protect the motor from wet weather. Do not allow any part of cord or

receptacle ends to sit in water or in damp locations. Failure to follow these warnings will result in

death or serious injury, and/or property damage.

• FIRE/EXPLOSION HAZARD.

Pump only clear water. Do not pump flammable or explosive fluids such as gasoline, fuel oil,

kerosene, etc. Do not use in a flammable and/or explosive atmosphere. Failure to follow these

warnings could result in death or serious injury and/or property damage.

• RISK OF ELECTRIC SHOCK.

These pumps have not been investigated for use in swimming pool areas.

• RISK OF ELECTRIC SHOCK.

Always disconnect power source before attempting to install, service, or maintain the pump.

Never handle a pump with wet hands or when standing on wet or damp surface or in water. Fatal

electrical shock could occur.

WARNING

• ELECTRICAL SHOCK ALERT.

Before installing this product, have the electrical circuit checked by an electrician to ensure proper

grounding. All electrical installations must conform to the National Electric Code and all local

codes.

• ELECTRICAL SHOCK ALERT.

Connect this product to a properly-grounded 115 volt circuit equipped with a Ground Fault Circuit

Interrupter (GFCI) device.

• ELECTRICAL SHOCK ALERT.

Do not handle pump or pump motor with wet hands or when standing on a wet or damp surface or

in water.

• ELECTRICAL SHOCK ALERT.

These pumps are supplied with a 3-prong grounded plug to help protect you against the possibility

of electrical shock. DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE GROUND PIN.

• ELECTRICAL SHOCK ALERT.

This pump is not intended to be permanently installed outdoors. Protect pump from extreme

heat, cold, and humidity. This pump is not waterproof and is not intended to be used in showers,

saunas, or other potentially wet locations. The motor is designed to be used in a clean, dry

location with access to an adequate supply of cooling air. Ambient temperature around the motor

should not exceed 104°F (40°C).

• ELECTRICAL SHOCK ALERT.

BE CERTAIN the pump power source is disconnected before installing or servicing pump.

• ELECTRICAL SHOCK ALERT.

Protect electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord.

• CHEMICAL ALERT.

This product contains chemicals known to the state of California to cause cancer and birth defects

or other reproductive harm.

• PERSONAL INJURY/PRODUCT DAMAGE ALERT.

Provide a means of pressure relief if the pump discharge can be shut off or obstructed. Pumps

operating with a closed discharge can create hot liquid, which can cause burns.

• PERSONAL INJURY ALERT.

This pump is equipped with an automatic thermal overload and can restart without warning.

• PERSONAL INJURY ALERT.

Do not touch the motor when operating and allow the motor to cool before touching it after

operation. Motor is designed to operate at high temperatures.

PREPARATION

CAUTION

Before beginning installation of product, make sure all parts are present. Compare parts with

package contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Installation Time: 10 minutes

Tools may be required for assembly: Crescent wrench, PVC-safe pipe sealant or thread sealant tape.

• PERSONAL INJURY OR PRODUCT DAMAGE MAY RESULT.

This pump operates on 115 volts. Make certain that the power source conforms to the

requirements of your equipment.

• PRODUCT DAMAGE MAY RESULT.

The maximum temperature of the pumped liquid must not exceed 120°F (40°C). The minimum

allowable temperature is 40°F (4°C).

• PRODUCT DAMAGE MAY RESULT.

Be sure the water source and piping are clear of sand, dirt, and scale. Debris will clog the pump

and void the warranty. Use a screen or strainer on the inlet to prevent debris from entering the

pump.

• PRODUCT DAMAGE MAY RESULT.

Failure to protect the pump and piping from freezing will cause damage and void the warranty.

• PRODUCT DAMAGE MAY RESULT.

Do not run pump dry. Impeller and seal damage will result.

• PROPERTY DAMAGE MAY RESULT.

Drain all liquids from the system before servicing or storing.

• PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY RESULT.

Make sure the discharge hose is secure before starting the pump. A loose discharge hose can

whip around and cause personal injury or property damage.

• PROPERTY DAMAGE MAY RESULT.

Do not operate this product while unattended.

• PROPERTY DAMAGE MAY RESULT.

Check hoses for worn areas before use and make certain that all connections are tight.

• PRODUCT DAMAGE MAY RESULT.

This pump is designed to pump water only. It has not been evaluated for pumping chemicals.

Check hoses for worn areas before use and make certain that all connections are tight.

• PRODUCT DAMAGE MAY RESULT.

Inspect the pump regularly for damage and perform routine maintenance as needed.

GENERAL PUMP INFORMATION

This pump is designed to sprinkle lawns and small gardens from lakes, ponds, or rivers, empty or

ll stock tanks, remove standing water from ooded areas, transfer water or boost water pressure.

Flammable liquids such as gasoline, chemicals, or corrosive liquids should never be used with this

pump.

The pump is NOT designed to operate underwater.

SETUP

1. Before installing pump (A), have the electrical circuit checked by an electrician to ensure proper

grounding.

BE CERTAIN the pump (A) power source is disconnected before installing or servicing this unit.

Be sure the water source and piping are clear of sand, dirt, and scale. Debris will clog pump (A)

and void warranty.

Failure to protect pump (A) and piping from freezing could cause severe damage and will void the

warranty.

Do not run pump (A) dry.

INSTALLATION INSTRUCTIONS

PUMPING FROM LAKES, PONDS, OR SMALL

STREAMS

1. Set pump (A) as close as possible to the water

source, keeping the vertical distance from

the water to pump as short as possible and

no more than 20 ft. Place pump (A) on level

support. Protect against ooding and excessive

moisture.

Long lengths of pipe or hose and use of many

ttings will reduce the amount of water this unit

will pump. Use the smallest number of ttings

and shortest possible length of pipe or hose.

Water source

Outlet

Inlet

Maximum

20 ft.

vertical

distance

2. Pump (A) inlet connection is designed for 1

in. NPT thread. You can connect to the inlet

with either 1 in. NPT PVC or garden hose. For

garden hose connections, thread adapter (B)

into the inlet. Seal connections with PVC-safe

sealant or thread sealant tape.

NOTE: Minimize length of pipe and number of

ttings.

NOTE: The inlet hose must be a reinforced

type when pumping from lakes, ponds, or small

streams. Regular garden hose will collapse and

lead to failure of pump (A). Inlet line should be

the same diameter as the discharge line, or

larger.

3. Attach garden hose to adapter (B) or connect

1 in. PVC pipe directly to pump (A) inlet. A foot

valve with strainer (not provided) should be

installed at the end of the discharge hose or

pipe to maintain prime during operation.

4. Seal all connections in the inlet hose with

PVC-safe sealant or thread sealant tape (not

provided). An air leak in the fittings, hose,

pipe, or connections will reduce pump (A)

performance and lead to pump failure.

Inlet

Seal all

connections

Water source

Inlet

Foot valve

PVC pipe or

reinforced

hose

Inlet with

1-in. NPT

PVC

Inlet with

adapter and

reinforced

garden hose

5. Connect 1 in. NPT pipe or garden hose to pump

(A) discharge. For garden hose connections,

thread adapter (B) into the discharge before

connecting the hose.

BOOSTING WATER PRESSURE

6. Connect 1 in. NPT pipe or garden hose to pump

(A) as in step 2. Connect the other end of the

inlet line to water supply such as a spigot.

Connect outlet pipe or hose to pump (A).

Do not run pump (A) with outlet

pipe or nozzle closed. The hose may burst

from excessive pressure. Use only reinforced

high-pressure hose or pipe for outlet pipe when

boosting water pressure.

Outlet

Inlet

Outlet with

1 in. NPT

PVC

Outlet with

adapter and

garden hose

DISCHARGE

PRESSURE (PSI)

GALLONS PER

HOUR

5 800

10 700

17 600

25 500

30 400

40 200

50 100

Power supply required 115 Volts, 60 Hz

Maximum water

temperature

104°F (40°C)

Individual branch circuit

required

15 AMP minimum

Discharge connection 1 in. NPT

Inlet connection 1 in. NPT

Water depth rating Maximum of 25 ft.

2. Reinstall priming plug on pump (A).

3. Turn pump (A) switch to the “off” position and

connect power cord to GFCI outlet.

NOTE: Pump (A) is for use only on 120 volt

(single phase), 60 Hz, 15 amp service, and is

equipped with a 3-conductor cord and e-prong,

grounding type plug.

Use a grounded receptacle

to reduce the risk of fatal electric shock. Never

cut off the round grounding prong on the power

cord. Cutting the cord or plug will make pump

(A) unsafe to operate and void the warranty.

On/o

switch

Priming

Plug

1. Remove priming plug on pump (A) and ll with

water.

Never run pump (A) dry.

Running pump without water will cause seal

failure. Fill pump (A) with water before starting,

unless the pump is used for pressure boosting.

NOTE: For boosting water pressure: Do

not remove priming plug. Turn on the water

supply. (See Step 6 in INSTALLATION

INSTRUCTIONS).

IL1858

Priming

Port

OPERATING INSTRUCTIONS

CARE AND MAINTENANCE

4. Turn pump (A) switch to the “on” position. If the

pump does not pump water within 5 minutes,

turn off pump (A) and repeat steps 1 through 4.

Check the following:

- Vertical distance of pump (A) to water level

must not be more than 20 feet.

- Inlet line must be airtight.

- All valves in inlet and discharge line must be

open.

Maintain adequate ventilation for the pump motor.

The motor bearings are permanently lubricated at

the factory. Additional lubrication is not required.

DRAINING FOR WINTER

Always protect pump (A) and piping against

freezing temperatures. If there is any danger of

freezing, drain the system.

1. Disconnect inlet and discharge lines from

pump (A).

2. Remove drain plug from lower front face of

pump (A).

3. Drain all piping below the frost line, or store

piping indoors.

4. Store pump (A) indoors.

Discharge piping

Inlet

piping

Outlet

Inlet

Drain

plug

Water source

Outlet

Inlet

Maximum

20 ft.

vertical

distance

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Motor will not

run.

1. Disconnect switch is off. 1. Be sure switch is on.

2. Fuse or circuit breaker is blown. 2. Replace fuse or reset circuit

breaker.

3. Starting switch is defective. 3. Replace starting switch.

4. Wires at motor are loose, disconnected

or wired incorrectly.

4. Refer to wiring instructions. Check

and tighten all wiring.

Capacitor voltage may be hazardous. To discharge capacitor,

touch short capacitor terminals with an insulated screwdriver. BE SURE to hold

handle of screwdriver while making contact with capacitor terminals.

Motor runs hot

and overload

kicks off.

1. Motor is wired incorrectly. 1. Refer to wiring instructions.

2. Voltage is too low. 2. Check with power company.

Install heavier wiring if wire size is

too small.

3. Pump (A) enclosure is not properly

vented.

3. Be sure pump (A) has sufficient

ventilation to cool the motor.

4. Collapsed inlet hose. 4. Replace with reinforced hose.

Motor runs but

no water is de-

livered.

NOTE: Check

prime before

looking for other

causes. Un-

screw priming

plug and check

for water in

pump housing.

1. NEW INSTALLATIONS - Pump (A)

does not prime as a result of:

a. Improper priming

b. Air leaks

c. Leaking foot valve

1. NEW INSTALLATIONS:

a. Re-prime according to

instructions.

b. Check all connections on inlet

line for leaks.

c. Replace foot valve.

2. EXISTING INSTALLATIONS - Pump

(A) does not prime as a result of:

a. Air leaks

b. Water level below inlet of pump (A)

2. EXISTING INSTALLATIONS:

a. Check all connections on inlet

line and shaft seal.

b. Lower inlet line into water and

re-prime.

3. Impeller is plugged. 3. Clean impeller.

4. Check valve or foot valve is stuck in

closed position.

4. Replace check valve or foot valve.

5. Pipes are frozen. 5. Thaw pipes. Bury pipe below frost

line. Protect pump (A) in a pit or

pump house.

6. Foot valve and/or strainer are buried in

sand or mud.

6. Raise foot valve and/or strainer

above any sand or mud.

7. Collapsed inlet hose. 7. Replace with reinforced hose.

Printed in China

WARRANTY

This product is warranted for one year from the date of purchase or two years from the date of manufacture,

whichever occurs rst. Subject to the conditions hereinafter set forth, the manufacturer will repair or replace

to the original consumer, any portion of the product which proves defective due to defective materials or

workmanship. This warranty does not cover replacement parts for failure due to normal wear and tear. To

obtain warranty service, contact the retailer from whom the product was purchased. The manufacturer retains

the sole right and option to determine whether to repair or replace defective equipment, parts or components.

Damage due to conditions beyond the control of the manufacturer is not covered by this warranty. For warranty

questions or service, call

1-866-994-4148.

THIS WARRANTY WILL NOT APPLY: (a) To defects or malfunctions resulting from failure to properly install,

operate or maintain the unit in accordance with printed instructions provided; (b) to failures resulting from

abuse, accident or negligence; (c) to normal maintenance services and the parts used in connection with

such service; (d) to units which are not installed in accordance with normal applicable local codes, ordinances

and good trade practices; and (e) the unit is used for purposes other than for what it was designed and

manufactured.

RETURN OF WARRANTED COMPONENTS: Any item to be repaired or replaced under this warranty must be

returned to the manufacturer at such place as the manufacturer may designate, freight prepaid.

THE WARRANTY PROVIDED HEREIN IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND MAY

NOT BE EXTENDED OR MODIFIED BY ANYONE. ANY IMPLIED WARRANTIES SHALL BE LIMITED TO

THE PERIOD OF THE LIMITED WARRANTY AND THEREAFTER ALL SUCH IMPLIED WARRANTIES ARE

DISCLAIMED AND EXCLUDED. THE MANUFACTURER SHALL NOT, UNDER ANY CIRCUMSTANCES, BE

LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO

DAMAGE TO, OR LOSS OF, OTHER PROPERTY OR EQUIPMENT, LOSS OF PROFITS, INCONVENIENCE,

OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY TYPE OR NATURE. THE LIABILITY

OF THE MANUFACTURER SHALL NOT EXCEED THE PRICE OF THE PRODUCT UPON WHICH SUCH

LIABILITY IS BASED.

This warranty gives you specic legal rights, and you may have other rights which vary from state to

state. Some states do not allow limitations on duration of implied warranties or exclusion of incidental or

consequential damages, so the above limitations may not apply to you.

PART DESCRIPTION PART #

B Garden Hose Adapters 025061

C Drain Plug and Priming Plug 025062

D Impeller, Diffuser, Nozzle Kit 024609

There are no warranty replacement parts available for this product. For non-warranty replacement

parts listed below, call our customer service department at 1-866-994-4148,

7:30 a.m. - 5:00 p.m., EST, Monday - Friday.

B C

REPLACEMENT PARTS LIST

In those instances where damages are incurred as a result of an alleged pump failure, the

Homeowner must retain possession of the pump for investigation purposes.

BOMBA REFORZADORA

PARA USO GENERAL

ARTÍCULO #0955585

MODELO #148008

Número de serie

Fecha de compra

¿Preguntas, problemas, piezas faltantes? Antes de volver a la tienda, llame a nuestro

Departamento de Servicio al Cliente al 1- 866-994-4148, de lunes a viernes de 7:30 a.m.

a 5:00 p.m., hora estándar del Este.

ADJUNTE SU RECIBO AQUÍ

SW1116S B

CONTENIDO DEL PAQUETE

INFORMACIÓN DE SEGURIDAD

PIEZA DESCRIPCIÓN CANTIDAD

A Bomba 1

B Adaptadores de manguera para jardín 2

Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el

producto.

NOTA: Las bombas con la marca “UL” y con la marca “US” se prueban para cumplir con los

estándares UL778 de UL. Las bombas con certicación CSA cumplen con el estándar CSA C22.2 No.

108. (CUS.)

PELIGRO

• PELIGRO DE DESCARGA ELÉCTRICA.

Esta bomba no es sumergible. Mantenga el motor seco en todo momento. No lave el motor. No

sumerja la bomba en agua. Proteja al motor del clima húmedo. No permita que ninguna parte del

cable ni los extremos del tomacorriente se apoyen en el agua ni en lugares húmedos. No seguir

estas instrucciones puede provocar la muerte, lesiones graves o daños a la propiedad.

• PELIGRO DE INCENDIO O EXPLOSIÓN.

Bombee solo agua limpia. No bombee líquidos inflamables o explosivos, como gasolina,

gasoil, queroseno, etc. No la utilice en una atmósfera inflamable o explosiva. No seguir estas

instrucciones puede provocar la muerte, lesiones graves o daños a la propiedad.

• RIESGO DE DESCARGA ELÉCTRICA.

No se ha verificado el uso de estas bombas en piscinas.

• RIESGO DE DESCARGA ELÉCTRICA.

Desconecte siempre la fuente de alimentación antes de intentar instalar, reparar o realizarle

mantenimiento a la bomba. Nunca manipule una bomba con las manos mojadas ni cuando esté

parado sobre una superficie húmeda o en el agua. Podría ocurrir una descarga eléctrica fatal.