Zoeller SPCP02 Manual de usuario

Marca: Zoeller

Modelo: SPCP02

Tipo: Manual de usuario

El Zoeller SPCP02 es una bomba eléctrica para piscinas que puede bombear hasta 2400 galones de agua por hora a una altura de 0 pies. Es capaz de bombear agua sucia y puede usarse para drenar piscinas cubiertas, spas y estanques pequeños. También se puede usar para transferir agua de un lugar a otro, como de un barril de lluvia a un jardín. La bomba tiene un motor de 1/3 HP y está equipada con un interruptor de circuito por falla a tierra (GFCI) para mayor seguridad.

POOL COVER PUMP

MODEL #SPCP02

Español p. 11

Serial Number Purchase Date

ATTACH YOUR RECEIPT HERE

SW1694 A

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-742-5044, 7:30 a.m. - 5:00 p.m., EST, Monday - Friday.

PACKAGE CONTENTS

SAFETY INFORMATION

DESCRIPTION QUANTITY

Pump 1

Base 1

Garden Hose Adaptor 1

Cap 1

Please read and understand this entire manual before attempting to assemble, operate, or install

the product.

• NOTE: Pumps with the “UL” Mark and pumps with the “US” mark are tested to UL Standard

UL778. CSA certied pumps are certied to CSA Standard C22.2 No. 108. (CUS.)

DANGER

• FIRE/EXPLOSION HAZARD.

Pump only clear water. Do not pump ammable or explosive uids such as gasoline, fuel oil,

kerosene, etc. Do not use in a ammable and/or explosive atmosphere. Failure to follow these

warnings could result in death or serious injury and/or property damage.

• RISK OF ELECTRIC SHOCK.

Always disconnect power source before attempting to install, service, or maintain the pump.

Never handle a pump with wet hands or when standing on wet or damp surface or in water. Fatal

electrical shock could occur.

PERFORMANCE FROM TOP OUTLET - UTILITY PUMP

ITEM

NUMBER

CORD

LENGTH HP AMPS

GALLONS PER HOUR AT DISCHARGE HEIGHT

ABOVE PUMPING LEVEL

0 FT. 5 FT. 10 FT. 15 FT. 20 FT.

SPCP02 25 FT. 1/3 3.0 2400 2100 1680 1380 600

PERFORMANCE FROM SIDE OUTLET WITH GARDEN HOSE

AT 0FT. ABOVE PUMPING LEVEL

HOSE LENGTH GALLONS PER MINUTE GALLONS PER HOUR

25 FT. 7.7 462

50 FT. 4.5 270

75 FT. 3.9 234

100 FT. 3.0 180

WARNING

CAUTION

• ELECTRICAL SHOCK ALERT.

Before installing this product, have the electrical circuit checked by an electrician to ensure proper

grounding. All electrical installations must conform to the National Electric Code and all local

codes.

• ELECTRICAL SHOCK ALERT.

Connect this product to a properly-grounded 115 volt outlet with a ground fault circuit interrupter

(GFCI) device.

• ELECTRICAL SHOCK ALERT.

Do not handle pump or pump motor with wet hands or when standing on a wet or damp surface or

in water.

• ELECTRICAL SHOCK ALERT.

DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE GROUND PIN.

• ELECTRICAL SHOCK ALERT.

BE CERTAIN the pump power source is disconnected before installing or servicing pump.

• ELECTRICAL SHOCK ALERT.

Protect electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord.

Replace or repair damaged or worn cords immediately.

• CHEMICAL ALERT.

This product contains chemicals known to the state of California to cause cancer and birth defects

or other reproductive harm.

• PERSONAL INJURY ALERT.

Provide a means of pressure relief if the pump discharge can be shut o or obstructed. Pumps

operating with a closed discharge can create hot liquid, which can cause burns.

• PERSONAL INJURY ALERT.

This pump is equipped with an automatic thermal overload and can restart without warning.

• PERSONAL INJURY ALERT.

Always use handle to lift pump. Never use power cord to lift pump. To avoid skin burns, unplug and

allow the pump to cool after periods of extended use.

• PERSONAL INJURY OR PRODUCT DAMAGE MAY RESULT.

Check to be sure your power source is capable of handling the voltage requirements of the motor,

as indicated on the pump name plate.

• PRODUCT DAMAGE MAY RESULT.

These pumps are not designed or intended to be used to handle sewage or euent.

• PRODUCT DAMAGE MAY RESULT.

This pump has been evaluated for use with WATER only.

• PRODUCT DAMAGE MAY RESULT.

Maximum continuous operating water temperature for standard model pumps must not exceed

104°F (40°C).

• PROPERTY DAMAGE MAY RESULT.

Do not use where sh are present. Oil in motor can kill sh.

• PERSONAL INJURY RESULT.

Secure the discharge hose before starting the pump. A loose discharge hose may whip, which can

cause personal injury and/or property damage.

• PRODUCT DAMAGE MAY RESULT.

Keep the pump, base, and inlet screen free of debris and foreign objects.

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 5 minutes

No Tools Required for Assembly.

PREPARATION

POOL COVER PUMP INSTALLATION INSTRUCTIONS

2. Attach garden hose adapter to the top pump

discharge. DO NOT OVER-TIGHTEN THE

HOSE ADAPTER. Finger tight plus 1/4 to 1/2

turn should be sucient.

Ensure cap is installed on top discharge.

For best performance, use discharge hose of 50 ft. or less. If the discharge runs up hill, or is extra

long, use larger diameter discharge hose or rigid pipe.

NOTE: Large diameter, short discharge hoses or pipe will provide better water ow rates than small

diameter, long discharge hoses or pipe.

1. Install the snap-on strainer by lining up the

pump base to match the strainer. Push down

gently until it latches.

4. Place pump in an upright position on the pool

cover where water will collect. Do not suspend

pump by the discharge hose or power cord.

Be sure pump is not sitting in mud, sand, or

debris.

5. Plug the pump into a properly grounded, ground

fault circuit interruptor (GFCI) 115 V outlet. For

safety, the pump should always be electrically

grounded to a suitable electrical ground, such

as a grounded water pipe, properly grounded

metallic raceway, or ground wire system.

3. For best stability, attach garden hose to lower

discharge. 1-1/4” top discharge may be used

with proper support of discharge line and pump.

If using garden hose (not included), thread the

female end of the garden hose into the male

end near the bottom of the pump. DO NOT

OVER-TIGHTEN THE HOSE. Finger tight plus

1/4 to 1/2 turn should be sucient.

For best performance, unwind the hose before

starting the pump.

3. Place pump in the water on a hard surface.

Water must be at least 1-3/4-in deep in order for

pump to operate. Avoid placing pump directly on

sand, dirt, or mud.

Hard

Surface

UTILITY PUMP INSTALLATION INSTRUCTIONS

2. Attach garden hose adapter to the pump

discharge and then connect garden hose

to adapter. DO NOT OVER-TIGHTEN THE

GARDEN HOSE OR HOSE ADAPTER. Finger

tight plus 1/4 to 1/2 turn should be sucient.

Attach cap to bottom outlet.

1. To enable pump to t into smaller spaces

remove snap on base from pump by pulling the

tab outward. This allows the pump to lift out of

the base.

4. Plug pump into a properly grounded, ground

fault circuit interrupter (GFCI) 115V AC power

outlet.

RESET

TEST

GFCI Outlet

OPERATION

1. Water must be a minimum of 1-3/4-in deep for pump

to operate.

The pump will run for 15 seconds after it is plugged in.

If water is being pumped during this 15 seconds, the

pump will continue operating until water level drops to

1/8-in. At that time, the pump will shut o.

After the pump shuts o, it will automatically turn

back on every three minutes for 15 seconds and then

turn back o if it is not pumping water. To re-start the

pump sooner, unplug the pump for a few seconds and

plug it back in.

NOTE: This pump does not contain a water level

sensor but will automatically shut itself o when water

level drops to 1/8-in. A built-in timer turns the pump

back on after 3 minutes and it will continue pumping

as long as water is present.

IL2059

1-3/4-in

minimum

to operate

2. To prevent unnecessary wear, unplug the pump from

the power output when not in use.

CAUTION: Extended usage of the pump in a partially

submerged or non-submerged situation may cause

the pump to overheat due to lack of heat dissipation

from the water. If this occurs, the pump will shut itself

o until the motor cools to its normal temperature.

Repeated overheating may cause damage to the

pump.

RESET

TEST

Unplug

Pump

Low Water

CARE AND MAINTENANCE

The motor housing of pump is completely sealed and requires no service. Disassembly of the motor

housing or alteration of the power cord voids all warranty.

1. Periodically unplug pump to inspect the inlet and

remove any debris. Make sure your hands are

dry and that you are not standing in water. Unplug

pump

Remove

debris

2. If pump clogs, unplug the pump from the power

supply. Attach one end of a garden hose to a

spigot and the other end to pump discharge.

Turn on the spigot to run water through pump to

clean it out.

3. If the pump becomes clogged, remove the

screen and clean out the area.

Debris in the intake should be routinely removed

from the bottom of the pump to prevent damage

to the pump, which will void the warranty.

Remove

Screen

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Pump runs,

but no water is

discharged.

1. Hose kinked. 1. Straighten hose.

2. Defective pump. 2. Replace pump.

3. Discharge height too great. 3. Reduce discharge height.

4. Clogged inlet. 4. Clean inlet.

5. Low line voltage. 5. Call power company.

6. Impeller is clogged. 6. Unplug pump and clean out

impeller.

7. Garden hose diameter is too small or

too long.

7. Use larger diameter garden hose

or 1 in. flexible pipe.

Motor runs too hot. 1. Voltage incorrect. 1. Connect to 115 volt GFCI outlet.

2. Restricted discharge hose. 2. Increase hose diameter to 3/4-in.

3. Pump damaged. 3. Replace pump.

4. Plugged or kinked discharge. 4. Clean and straighten hose.

Flow rate is low. 1. Hose kinked. 1. Straighten hose.

2. Clogged impeller. 2. Clear obstruction.

3. Excessive length of hose. 3. Reduce length of outlet hose.

Pump will not run. 1. No power. 1. Verify that unit is plugged into 115

volt GFCI outlet.

2. Motor overheated. 2. Motor has automatic thermal

protector. Wait 15 minutes for

motor to cool.

3. Blown fuse or circuit breaker. 3. Reset the circuit breaker or replace

fuse with a fuse of the proper size.

4. Low line voltage. 4. Call power company.

5. Defective motor. 5. Replace pump.

6. Water level is too low. 6. Allow the water level to rise to

1-3/4 in. or more.

7. GFCI needs to be reset. 7. Press reset button on GFCI outlet.

TROUBLESHOOTING

WARRANTY

This product is warranted for two years from the date of purchase. Subject to the conditions

hereinafter set forth, the manufacturer will repair or replace to the original consumer, any portion of

the product which proves defective due to defective materials or workmanship. This warranty does

not cover replacement parts for failure due to normal wear and tear. To obtain warranty service,

contact the dealer from whom the product was purchased. The manufacturer retains the sole right

and option to determine whether to repair or replace defective equipment, parts or components.

Damage due to conditions beyond the control of the manufacturer is not covered by this warranty.

THIS WARRANTY WILL NOT APPLY:

(a) To defects or malfunctions resulting from failure to properly install, operate or maintain the unit in

accordance with printed instructions provided;

(b) to failures resulting from abuse, accident or negligence or use of inappropriate chemicals or

additives in the water;

(d) to units which are not installed in accordance with normal applicable local codes, ordinances and

good trade practices; and

(e) if the unit is used for purposes other than for what it was designed and manufactured.

RETURN OF WARRANTED COMPONENTS:

Any item to be repaired or replaced under this warranty must be returned to the manufacturer at

Kendallville, Indiana or such other place as the manufacturer may designate, freight prepaid.

THE WARRANTY PROVIDED HEREIN IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES,

AND MAY NOT BE EXTENDED OR MODIFIED BY ANYONE. ANY IMPLIED WARRANTIES SHALL

BE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY AND THEREAFTER ALL SUCH

IMPLIED WARRANTIES ARE DISCLAIMED AND EXCLUDED. THE MANUFACTURER SHALL

NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR

SPECIAL DAMAGES, SUCH AS, BUT NOT LIMITED TO DAMAGE TO, OR LOSS OF, OTHER

PROPERTY OR EQUIPMENT, LOSS OF PROFITS, INCONVENIENCE, OR OTHER INCIDENTAL

OR CONSEQUENTIAL DAMAGES OF ANY TYPE OR NATURE. THE LIABILITY OF THE

MANUFACTURER SHALL NOT EXCEED THE PRICE OF THE PRODUCT UPON WHICH SUCH

LIABILITY IS BASED.

This warranty gives you specic legal rights, and you may have other rights which vary from state to

state. Some states do not allow limitations on duration of implied warranties or exclusion of incidental

or consequential damages, so the above limitations may not apply to you.

In those instances where damages are incurred as a result of an alleged pump failure, the

Homeowner must retain possession of the pump for investigation purposes.

Printed in Taiwan

BOMBA DE CUBIERTA

PARA PISCINA

MODELO #SPCP02

SW1694 A

Número de serie Fecha de compra

¿Preguntas, problemas, partes faltantes? Antes de acudir al minorista, llame a nuestro

departamento de servicio al cliente al 1-800-742-5044, de lunes a viernes de 7:30 a.m. a

5:00 p.m., EST.

ADJUNTE SU RECIBO AQUÍ

CONTENIDO DEL PAQUETE

INFORMACIÓN DE SEGURIDAD

DESCRIPCIÓN CANTIDAD

Bomba 1

Base 1

Adaptador para

manguera

Tapa 1

Lea y comprenda completamente este manual antes de intentar ensamblar, usar o instalar el

producto.

• NOTA: las bombas con la marca “UL” y con la marca “US” se prueban para cumplir con los

estándares UL778 de UL. Las bombas con certicación CSA cumplen con el estándar CSA

C22.2 No. 108. (CUS.)

PELIGRO

• PELIGRO DE INCENDIO O EXPLOSIÓN.

Bombee solo agua limpia. No bombee líquidos inamables o explosivos como gasolina, gasoil, queroseno,

etc. No la utilice en una atmósfera inamable o explosiva. No seguir estas instrucciones puede provocar la

muerte, lesiones graves o daños a la propiedad.

• RIESGO DE DESCARGA ELÉCTRICA.

Desconecte siempre la fuente de alimentación antes de intentar instalar, reparar, reubicar o realizarle

mantenimiento a la bomba. Nunca manipule la bomba con las manos mojadas ni cuando esté parado

sobre una supercie húmeda o en el agua. Podría ocurrir una descarga eléctrica fatal.

FUNCIONAMIENTO DESDE LA SALIDA SUPERIOR - BOMBA DE SERVICIOS PÚBLICOS

NÚMERO

ARTÍCULO

LARGO

DEL

CABLE

HP AMPERES

LITROS POR HORA CON ALTURA DE DESCARGA

POR ENCIMA DEL NIVEL DE BOMBEO

0 M 1,5 M 3,0 M 4,6 M 6,1 M

SPCP02 25 FT. 1/3 3.0 9,084 7,949 6,359 5,224 2,271

FUNCIONAMIENTO DESDE LA SALIDA LATERAL CON MANGUERA DE JARDÍN

0 PIES POR ENCIMA DEL NIVEL DE BOMBEO

LONGITUD DE LA

MANGUERA

GALONES ESTADOUNIDENSES

POR MINUTO

GALONES ESTADOUNIDENSES

POR HORA

25 PIES 7.7 462

50 PIES 4.5 270

75 PIES 3.9 234

100 PIES 3.0 180