3M 1200204 Instrucciones de operación

Marca: 3M

Modelo: 1200204

Tipo: Instrucciones de operación

1 2

Hot Work

Arc Flash



x 1

2000112

3100064

3100107

3100108

9505254

2000023

2000209

2000210

2000214

2109193

9502058

9502116

9502195

1 2 3 4 5 6 7 8 9 10 11 12 13

ANSI OSHA

3101491 1

1 1

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101492 1

1 1

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101493 1

1 1

7 ft

(1.8 m)

311 lbs

(140 kg)

421 lbs

(190 kg)

3101494 1

1 1

8 ft

(1.8 m)

312 lbs

(140 kg)

422 lbs

(190 kg)

3101495 1

1 1

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101496 1

1 1

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101497 1

1 1

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101498 1

1 1

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101499 2

1 2

7 ft

(1.8 m)

311 lbs

(140 kg)

421 lbs

(190 kg)

3101500 2

1 2

8 ft

(1.8 m)

312 lbs

(140 kg)

422 lbs

(190 kg)

3101501 2

1 2

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101502 2

1 2

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101503 2

1 2

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101504 2

1 2

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101505 2

1 2

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101656 1

1 1

3.5 ft

(1.1 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101657 1

1 1

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101665 2

1 2

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

3101674 1

1 1

6 ft

(1.8 m)

310 lbs

(140 kg)

420 lbs

(190 kg)

1 2 3 4 5 6 7 8 9 10 11 12 13

ANSI Z359.14 Class B OSHA 1926.502

ANSI A10.32 OSHA 1910.140

INSTRUCTION MANUAL

5903613 Rev. D

Nano-Lok

SELF-RETRACTING DEVICE

A B

FC = FF+DD+SF



x 1

≤310 lb

V=2 ft, H=4 ft, FC = 12 ft



x 1

≤310 lb

3101656



x 1

≤310 lb

5 6

A B C

3101656

Delta III

ExoFit

NEX

D D

Delta III

ExoFit

NEX

13 14

A B

16 17 18 19

E F

A B C D

E F

SIT 5908239 Rev. C

SAFETY INFORMATION

Please read, understand, and follow all safety information contained in these instructions prior to the use of this Self-Retracting

Device (SRD). FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH.

These instructions must be provided to the user of this equipment. Retain these instructions for future reference.

Intended Use:

This Self-Retracting Device is intended for use as part of a complete personal fall protection system.

Use in any other application including, but not limited to, material handling, recreational or sports related activities, or other activities not

described in the User Instructions, is not approved by 3M and could result in serious injury or death.

This device is only to be used by trained users in workplace applications.

! WARNING

This Self-Retracting Device is part of a personal fall protection system. It is expected that all users be fully trained in the safe installation and

operation of their personal fall protection system. Misuse of this device could result in serious injury or death. For proper selection,

operation, installation, maintenance, and service, refer to these User Instructions including all manufacturer recommendations, see your

supervisor, or contact 3M Technical Services.

• To reduce the risks associated with working with an SRD which, if not avoided, could result in serious injury or death:

- Before each use, inspect the SRD and check for proper locking and retraction.

- If inspection reveals an unsafe or defective condition, remove the device from service and repair or replace according to the User

Instructions.

- If the SRD has been subjected to fall arrest or impact force, immediately remove the SRD from service and label the device ‘UNUSABLE’.

- Ensure the lifeline is kept free from any and all obstructions including, but not limited to; entanglement with moving machinery or

equipment (e.g., the top drive of oil rigs), other workers, yourself, surrounding objects, or impact from overhead objects that could fall

onto the lifeline or the worker.

- Never allow slack in the lifeline. Do not tie or knot the lifeline.

- Attach the unused leg(s) of the Harness Mounted SRD to the parking attachment(s) of the harness if equipped.

- Do not use in applications that have an obstructed fall path. Working on slowly shifting material, such as sand or grain, or within conned

or cramped spaces, may not allow the worker to reach sufcient speed to cause the SRD to lock. A clear path is required to assure

positive locking of the SRD.

- Avoid sudden or quick movements during normal work operation. This may cause the device to lock up.

- Ensure that fall protection systems/subsystems assembled from components made by different manufacturers are compatible and meet

the requirements of applicable standards, including the ANSI Z359 or other applicable fall protection codes, standards, or requirements.

Always consult a Competent and/or Qualied Person before using these systems.

• To reduce the risks associated with working at height which, if not avoided, could result in serious injury or death:

- Ensure your health and physical condition allow you to safely withstand all of the forces associated with working at height. Consult with

your doctor if you have any questions regarding your ability to use this equipment.

- Never exceed allowable capacity of your fall protection equipment.

- Never exceed maximum free fall distance of your fall protection equipment.

- Do not use any fall protection equipment that fails pre-use or other scheduled inspections, or if you have concerns about the use or

suitability of the equipment for your application. Contact 3M Technical Services with any questions.

- Some subsystem and component combinations may interfere with the operation of this equipment. Only use compatible connections.

Consult 3M prior to using this equipment in combination with components or subsystems other than those described in the User

Instructions.

- Use extra precautions when working around moving machinery (e.g. top drive of oil rigs) electrical hazards, extreme temperatures,

chemical hazards, explosive or toxic gases, sharp edges, or below overhead materials that could fall onto you or your fall protection

equipment.

- Use Arc Flash or Hot Works devices when working in high heat environments.

- Avoid surfaces and objects that can damage the user or equipment.

- Ensure there is adequate fall clearance when working at height.

- Never modify or alter your fall protection equipment. Only 3M or parties authorized in writing by 3M may make repairs to the equipment.

- Prior to use of fall protection equipment, ensure a rescue plan is in place which allows for prompt rescue if a fall incident occurs.

- If a fall incident occurs, immediately seek medical attention for the worker who has fallen.

- Do not use a body belt for fall arrest applications. Use only a Full Body Harness.

- Minimize swing falls by working as directly below the anchorage point as possible.

- If training with this device, a secondary fall protection system must be utilized in a manner that does not expose the trainee to an

unintended fall hazard.

- Always wear appropriate personal protective equipment when installing, using, or inspecting the device/system.

;

Before using this equipment, record the product identication information from the ID label in the ‘Inspection and

Maintenance Log’ at the back of this manual.

DESCRIPTION:

Figure 2 identies key components of the 3M™ DBI-SALA

Nano-Lok Self-Retracting Devices (SRDs). Nano-Lok SRDs are drum

wound Web Lifelines (A) with an in-line Energy Absorber (B) that retracts into a Nylon Housing (C). A Swivel Eye (D) on the

top of the Housing allows attachment to a valid anchorage connection point with a Carabiner (E), or mounting on a Full Body

Harness with a Harness Interface (F). Figure 1 identies available Nano-Lok models and their connector congurations. See

Table 1 for Nano-Lok SRD and connector specications.

Hot Work: Fire resistant “Hot Work” models are available for welding, foundry work, etc. where the SRD may be exposed

to sparks or ames for short durations.

Arc Flash: SRD meets the requirements of ATSM F887 and is designed for use in environments where an Arc Flash

(electrical explosion) could occur.

Table 1 – Specications

Component Specications:

SRL Housings Nylon

Drum Nylon

Internal Components Stainless Steel and Zinc Plated Steel

Web Lifeline Kevlar Nomex

Energy Absorber Cover: Kevlar Nomex, Web: Polyester, Stitching: Nomex

Swivel Zinc Plated Steel

Connector Specications:

Description Material Gate Opening Gate Strength Tensile Strength

Carabiner Steel 0.69 in (18 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Single SRD Interface Steel 11/16 in (17 mm) 5,000 lbs (22.2 kN)

Twin SRD Interface (Fixed D-Ring) Steel 3/4 in (19 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Twin SRD Interface Steel w/Nylon Insert 3/4 in (19 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Snap Hook Aluminum 1 in (25 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Carabiner Aluminum 3/4 in (19 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Rebar Hook Aluminum 2-1/2 in (64 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Rebar Hook Steel 2-1/2 in (64 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Rebar Hook Aluminum & Steel 2-1/2 in (64 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Rebar Hook Steel 2-1/2 in (64 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Rebar Hook Aluminum 2-1/4 in (57 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Snap Hook Steel 3/4 in (19 mm) 3,600 lbs (16 kN) 5,000 lbs (22.2 kN)

Performance Specications:

SRL Specications (Z359.14 Class B) ANSI/OSHA Models OSHA Models

Capacity Range 130 lbs - 310 lbs (59 kg - 140 kg) 311 lbs - 420 lbs (141 kg - 191 kg)

Maximum Arresting Force 1,350 lbs (6 kN) 1,350 lbs (6 kN)

Average Arresting Force 900 lbs (4 kN) 900 lbs (4 kN)

Claimed Maximum Arresting Distance

30 in (0.76 m) 36 in (0.9 m)

Minimum Fall Clearance Required

4 ft (1.2 m) 5 ft (1.5 m)

Maximum Free Fall

3 ft (0.91 m) 2 ft (0.61 m)

SRL Specications (Model 3101656) ANSI/OSHA Models OSHA Models

Capacity Range 130 lbs - 310 lbs (59 kg - 140 kg) 311 lbs - 420 lbs (141 kg - 191 kg)

Maximum Arresting Force 1,350 lbs (6 kN) 1,350 lbs (6 kN)

Average Arresting Force 900 lbs (4 kN) 900 lbs (4 kN)

Claimed Maximum Arresting Distance

30 in (0.76 m) 36 in (0.9 m)

Minimum Fall Clearance Required

5 ft (1.5 m) 5 ft (1.5 m)

Maximum Free Fall

3 ft (0.91 m) 2 ft (0.61 m)

1 - Assumes the SRL is mounted directly above (overhead) the end user.

2 - SRL must be mounted above user D-Ring

1.0 APPLICATIONS

1.1 PURPOSE: Self-Retracting Devices (SRDs) are designed to be a component in a personal fall arrest system (PFAS). Figure

1 illustrates SRDs covered by this instruction manual. They may be used in most situations where a combination of worker

mobility and fall protection is required (i.e. inspection work, general construction, maintenance work, oil production,

conned space work, etc.).

1.2 STANDARDS: Your SRD conforms to the national or regional standard(s) identied on the front cover of these

instructions. Refer to the local, state, and federal (OSHA) requirements governing occupational safety for additional

information regarding Personal Fall Protection.

1.3 TRAINING: This equipment is intended to be used by persons trained in its correct application and use. It is the responsibility of the

user to assure they are familiar with these instructions and are trained in the correct care and use of this equipment. Users must also

be aware of the operating characteristics, application limits, and the consequences of improper use.

1.4 LIMITATIONS: Always consider the following limitations when installing or using this equipment:

• Capacity: SRDs are for use by one person with a combined weight (clothing, tools, etc.) meeting the Capacity Range

specied in Table 1 for your standard(s). Make sure all of the components in your system are rated to a capacity

appropriate to your application.

• Anchorage: Anchorages selected for fall arrest systems shall have a strength capable of sustaining static loads

applied in the directions permitted by the system of at least:

1. 5,000 lbs. (22.2 kN) for non-certified anchorages, or

2. Two times the maximum arresting force for certified anchorages.

When more than one fall arrest system is attached to an anchorage, the strengths set forth in (1) and

(2) above shall be multiplied by the number of systems attached to the anchorage.

;

From OSHA 1926.502 and 1910.140: Anchorages used for attachment of personal fall arrest systems shall be

independent of any anchorage being used to support or suspend platforms, and capable of supporting at least 5,000 lbs.

per user attached, or be designed, installed, and used as part of a complete personal fall arrest systems which maintains

a safety factor of at least two, and is under the supervision of a qualied person.

• Locking Speed: Situations which do not allow for an unobstructed fall path should be avoided. Working in confined

or cramped spaces may not allow the body to reach sufficient speed to cause the SRD to lock if a fall occurs. Working

on slowly shifting material, such as sand or grain,may not allow enough speed buildup to cause the SRD to lock. A

clear path is required to assure positive locking of the SRD.

• Free Fall: When used correctly with the SRD anchored directly overhead and no slack in the lifeline, SRDs will limit the free

fall distance to 0 ft (0 cm)

. To avoid increased fall distances, do not work above the anchorage level. Do not lengthen

SRDs by connecting a lanyard or similar component without consulting 3M. Never clamp, knot, or prevent

the lifeline from retracting or staying taut. Avoid slack line.

• Swing Falls: Swing Falls occur when the anchorage point is not directly above the point where a fall occurs. The

force of striking an object in a swing fall may cause serious injury (see Figure 3A). Minimize swing falls by working as

directly below the anchorage point as possible (Figure 3B).

• Fall Clearance: Figure 3B illustrates Fall Clearance Calculation. Fall Clearance (FC) is the sum of Free Fall (FF),

Deceleration Distance (DD) and a Safety Factor (SF): FC = FF +DD + SF. D-Ring Slide and Harness Stretch are included in

the Safety Factor. Fall Clearance values have been calculated and are charted in Figure 4. A Safety Factor of 1.5 ft (0.5 m)

was used for all values in Figure 4.

For falls from a standing position where the SRD is anchored directly overhead (Figure 3B), SRD Fall Arrest Systems

should have the minimum Fall Clearances specied in Table 1. Falls from a kneeling or crouching position will require

an additional 3 ft (1 m) of Fall Clearance. In a swing fall situation (Figure 3C), the total vertical fall distance will be

greater than if the user had fallen directly below the anchorage point and may require additional Fall Clearance. Figure

4 and the accompanying table dene the Maximum Work Radius (C) for various SRD Anchorage Heights (A) and Fall

Clearances (B). The Recommended Work Zone is limited to the area located within the Maximum Work Radius.

• Hazards: Use of this equipment in areas where surrounding hazards exist may require additional precautions to reduce the

possibility of injury to the user or damage to the equipment. Hazards may include, but are not limited to: high heat, caustic

chemicals, corrosive environments, high voltage power lines, explosive or toxic gases, moving machinery, or overhead materials

that may fall and contact the user or fall arrest system. Avoid working where your lifeline may cross or tangle with that of another

worker. Avoid working where an object may fall and strike the lifeline; resulting in loss of balance or damage to the lifeline. Do not

allow the lifeline to pass under arms or between legs.

• Sharp Edges: Sharp edges the SRD lifeline can contact during a fall must have a minimum radius of 0.125 in (0.3

cm).

Where contact with a sharp edge is unavoidable, cover the edge with a protective material.

1 Free Fall: Correct application of the SRD, with the user working directly below the anchorage point and no lifeline slack, will eliminate Free Fall. Free Fall should be

limited to 5 ft (1.5 m) for a 310 lb (141 kg) capacity where the user is not directly under the SRD or minimal slack exists in the lifeline. See Figure 4 for acceptable

anchorage locations.

2.0 Use

2.1 FALL PROTECTION AND RESCUE PLAN: The employer must have a Fall Protection and Rescue Plan in place that meets

ANSI Z359.2 Minimum Requirements for a Comprehensive Managed Fall Protection Program. The plan should provide

guidelines and requirements for an employer’s managed fall protection program, including policies, duties and training;

fall protection procedures; eliminating and controlling fall hazards; rescue procedures; incident investigations; and

evaluating program effectiveness.

2.2 INSPECTION FREQUENCY:

SRDs shall be inspected by the authorized person

or rescuer

before each use (See Table

3). Additionally, inspections shall be conducted by a competent person

other than the user. Extreme working conditions

(harsh environment, prolonged use, etc.) may necessitate more frequent competent person inspections. The competent

person shall use the Inspection Schedule (Table 2) to determine appropriate inspection intervals.

Inspection procedures

are described in the Inspection & Maintenance Log (Table 3). Results of the Competent Person inspection should be recorded

in the Inspection and Maintenance Log or recorded with the Radio Frequency Identification (RFID) system (see Section 5).

2.3 NORMAL OPERATIONS: Normal operation will allow the lifeline to extend and retract with no hesitation or slack as

the worker moves at normal speeds. If a fall occurs, a speed sensing brake system will activate, stopping the fall and

absorbing much of the energy created. Sudden or quick movements should be avoided during normal work operation, as

this may cause the SRD to lock up. For falls which occur near the end of the lifeline travel, a reserve lifeline system or

Energy Absorber has been incorporated to reduce the fall arrest forces.

2.4 BODY SUPPORT: A Full Body Harness must be used with the Self-Retracting Device. The harness connection point must be

above the user’s center of gravity. A body belt is not authorized for use with the Self-Retracting Device. If a fall occurs when

using a body belt it may cause unintentional release or physical trauma from improper body support.

2.5 COMPATIBILITY OF COMPONENTS: Unless otherwise noted, 3M equipment is designed for use with 3M approved

components and subsystems only. Substitutions or replacements made with non approved components or subsystems may

jeopardize compatibility of equipment and may affect safety and reliability of the complete system.

2.6 COMPATIBILITY OF CONNECTORS: Connectors are considered to be compatible with connecting elements when they

have been designed to work together in such a way that their sizes and shapes do not cause their gate mechanisms to

inadvertently open regardless of how they become oriented. Contact 3M if you have any questions about compatibility.

Connectors (hooks, carabiners, and D-rings) must be capable of supporting at least 5,000 lbs. (22.2 kN). Connectors

must be compatible with the anchorage or other system components. Do not use equipment that is not compatible.

Non-compatible connectors may unintentionally disengage (see Figure 5). Connectors must be compatible in size, shape,

and strength. Self-locking snap hooks and carabiners are required. If the connecting element to which a snap hook or

carabiner attaches is undersized or irregular in shape, a situation could occur where the connecting element applies a

force to the gate of the snap hook or carabiner (A). This force may cause the gate to open (B), allowing the snap hook or

carabiner to disengage from the connecting point (C).

2.7 MAKING CONNECTIONS: Snap hooks and carabiners used with this equipment must be self-locking. Ensure all

connections are compatible in size, shape and strength. Do not use equipment that is not compatible. Ensure all

connectors are fully closed and locked. 3M connectors (snap hooks and carabiners) are designed to be used only as

specied in each product’s user’s instructions. See Figure 6 for examples of inappropriate connections. Do not connect

snap hooks and carabiners:

A. To a D-ring to which another connector is attached.

B. In a manner that would result in a load on the gate. Large throat snap hooks should not be connected to standard

size D-rings or similar objects which will result in a load on the gate if the hook or D-ring twists or rotates, unless the

snap hook is equipped with a 3,600 lb (16 kN) gate.

C. In a false engagement, where size or shape of the mating connectors are not compatible and, without visual

conrmation, the connectors seem fully engaged.

D. To each other.

E. Directly to webbing or rope lanyard or tie-back (unless the manufacturer’s instructions for both the lanyard and

connector specically allows such a connection).

F. To any object which is shaped or dimensioned such that the snap hook or carabiner will not close and lock, or that

roll-out could occur.

G. In a manner that does not allow the connector to align properly while under load.

Table 2 – Inspection Schedule

Type of Use Application Examples Conditions of Use Inspection Frequency

Infrequent to Light

Rescue and Conned Space,

Factory Maintenance

Good Storage Conditions, Indoor or Infrequent

Outdoor Use, Room Temperature, Clean Environments

Annually

Moderate to Heavy

Transportation, Residential

Construction, Utilities, Warehouse

Fair Storage Conditions, Indoor and Extended Outdoor

Use, All Temperatures, Clean or Dusty Environments

Semi-Annually to

Annually

Sever to Continuous

Commercial Construction, Oil and

Gas, Mining

Harsh Storage Conditions, Prolonged or Continuous

Outdoor Use, All Temperatures, Dirty Environment

Quarterly to Semi-

Annually

1 Authorized Person: A person assigned by the employer to perform duties at a location where the person will be exposed to a fall hazard.

2 Rescuer: Person or persons other than the rescue subject acting to perform an assisted rescue by operation of a rescue system.

3 Competent Person: An individual designated by the employer to be responsible for the immediate supervision, implementation, and monitoring of the employer’s

managed fall protection program who, through training and knowledge, is capable of identifying, evaluating, and addressing existing and potential fall hazards, and

who has the employer’s authority to take prompt corrective action with regard to such hazards.

3.0 Installation

3.1 PLANNING: Plan your fall protection system before starting your work. Account for all factors that may affect your safety

before, during, and after a fall. Consider all requirements and limitations dened in Section 2.

;

In most applications, the Nano-Lok SRD can be connected to the anchorage or the harness Dorsal location. Either

orientation is allowed; except as noted in Section Section 4

3.2 ANCHORAGE: Figure 7 illustrates typical SRD anchorage connections. Select an anchorage location with minimal free fall and

swing fall hazards (see Section 1). Select a rigid anchorage point capable of sustaining the static loads dened in Section 1.

Where anchoring overhead is not feasible, Nano-Lok SRDs may be secured to an anchorage point as low as foot level, but will

require increased clearance values (see Figure 4).

3.3 HARNESS MOUNTING: Some SRD models include a Single SRD or Twin SRD Harness Interface for mounting the SRD(s)

on a Full Body Harness just below the Dorsal D-Ring:

;

Some Full Body Harnesses are equipped with a Personal SRD Link (PSRL Link) that integrates the Dorsal D-Ring

with attachment elements for Harness Mounted Self-Retracting Devices (Figure 8). It is also acceptable to connect the

SRD to the Harness Dorsal D-Ring with a Carabiner or Snaphook.

• Single SRD Harness Interface: Where worker mobility is critical, a Single SRD Harness Interface can be used to mount

the SRD on the back of a Full Body Harness just below the Dorsal D-Ring (see Figure 9). The worker can then connect to

varied anchorage points located throughout the site with the Lanyard End of the SRD without repeatedly reinstalling the

SRD. To mount the SRD on a Full Body Harness with the Single SRD Harness Interface:

1. Loosen the Harness Webbing: Pull out on the Web Straps (A) where they pass through the bottom of the

Dorsal D-Ring (B) until there is sufcient space to slide the Single SRD Interface between the Web Straps and

Back Pad.

2. Open the Harness Interface: Push down on the Locking Buttons (C) simultaneously and slide the Locking Pin

(D) out.

3. Position the Harness Interface around the Web Straps: With the Locking Buttons (C) facing out and Gate

facing up, insert the Nose End of the Harness Interface (E) behind the Web Straps (A). Rotate the Harness

Interface behind the Web Straps until the Harness Interface surrounds the the Web Straps. Pull the Web Straps

back through the Dorsal D-Ring and Back Pad to secure the Harness Interface.

4. Attach the SRD to the Harness Interface: Slide the Swivel Eye on the SRD (F) over the Harness Interface’s

Locking Pin (D) and then push in the Locking Pin until it locks into place in the opposite end of the Harness

Interface.

;

The Red Band on the knob end of the Harness Interface Locking Pin will be exposed if the Harness

Interface is unlocked. To avoid accidental release of the connection, always make sure the Harness Interface

is locked before using the Harness and attached SRD. Failure to do so could result in injury or death.

• Twin SRD Harness Interface: In climbing applications where 100% tie-off is required, the Twin SRD Harness

Interface can be used to mount two SRDs side-by-side on the back of a Full Body Harness just below the Dorsal

D-Ring (see Figure 10) To mount two SRDs on a Full Body Harness with the Twin SRD Harness Interface:

1. Loosen the Harness Webbing: Pull out on the Web Straps (A) where they pass through the bottom of the

Dorsal D-Ring (B) until there is sufcient space to slide the Twin SRD Interface between the Web Straps and

D-Ring Pad.

2. Open the Harness Interface: Push up on the Connector Insert (C) to unsnap the Clamps (D) from the

Connector and then swing the Connector Insert up to unlock the Gate. Push the Gate (E) inward to open the

Connector.

3. Thread the rst SRD onto the Harness Interface: Insert the Nose of the Connector (F) through the Swivel

Eye (G) on the SRD and then rotate the SRD around to the Gate End of the Connector (H). The Gate can be

rotated toward the Nose to allow clearance for the Swivel Eye between the Gate and Spine of the Connector.

4. Position the Harness Interface around the Web Straps: With the Gate facing up, insert the Nose of the

Connector (F) behind the Web Straps (A). Rotate the Connector behind the Web Straps until the Connector

surrounds the the Web Straps.

5. Add the second SRD on the Harness Interface: Slide the SRD’s Swivel Eye (G) over the Nose of the

Connector (F) and position the SRD Swivel Eye in the Nose End of the Connector (I). Swing the Gate (E) closed.

6. Close the Harness Interface: Rotate the Connector Insert (C) forward so the Clamps (D) secure on the

Connector. When properly closed, the Web Straps should pass through the Webbing Slot (J) at the top of the

Connector Insert and the SRD Swivel Eyes should be secured in the Recesses (K) on either side of the Connector

Insert. Once the Harness Interface is closed, pull the Web Straps (A) back through the Dorsal D-Ring and D-Ring

Pad to eliminate slack in the webbing and secure the Connector between the Web Straps and D-Ring Pad.

• Twin SRD Fixed D-Ring Harness Interface: Older ExoFit Full Body Harnesses with a Fixed D-Ring require a special

Twin SRD Harness Interface to mount two SRDs on the back of the harness just below the Dorsal D-Ring. To mount

two SRDs on an ExoFit Full Body Harness with the Twin SRD Fixed D-Ring Harness Interface (Figure 11):

1. Loosen the Harness Webbing: Pull out on the Web Straps (A) where they pass through the bottom of the

Dorsal D-Ring (B) until there is sufcient space to insert the Twin SRD Interface between the Web Straps and

Back Pad.

2. Open the Harness Interface: With the Twin SRD Interface orientated as illustrated, push the Locking Sleeve

3. Thread the rst SRD onto the Harness Interface: Insert the Nose of the Connector (E) through the Swivel

Eye (F) on the SRD and then rotate the SRD around to the Gate End of the Connector (G). The Gate can be

closed to allow clearance for the Swivel Eye between the Gate and Spine of the Connector.

4. Position the Harness Interface around the Web Straps: Insert the Nose of the Connector (E) behind the

Web Straps (A). Rotate the Connector behind the Web Straps until the Connector surrounds the Web Straps.

5. Add the second SRD on the Harness Interface: Slide the SRD’s Swivel Eye (F) over the Nose of the

Connector (E) and position the SRD Swivel Eye in the Nose End of the Connector.

6. Close the Harness Interface: Allow the Gate (D) to swing closed and the Locking Sleeve (C) to rotate back to

locked position. Once the Harness Interface is closed, pull the Web Straps (A) back through the Dorsal D-Ring to

eliminate slack in the webbing and secure the Harness Interface between the Web Straps and Back Pad.

4.0 OPERATION

;

First time or infrequent users of Self-Retracting Devices (SRDs) should review the “Safety Information” at the

beginning of this manual prior to use of the SRD.

4.1 BEFORE EACH USE: Before each use of this fall protection equipment carefully inspect it to assure it is in good working

condition. Check for worn or damaged parts. Ensure all bolts are present and secure. Check that the lifeline is retracting

properly by pulling out the line and allowing it to slowly retract. If there is any hesitation in retraction the unit should be

removed from service and destroyed. Inspect the lifeline for cuts, frays, burns, crushing and corrosion. Check locking

action by pulling sharply on the line. See the Inspection and Maintenance Log (Table 3) for inspection details. Do not use

if inspection reveals an unsafe condition.

4.2 AFTER A FALL: Any equipment which has been subjected to the forces of arresting a fall or exhibits damage consistent

with the effect of fall arrest forces as described in Table 3, must be removed from service immediately and destroyed.

4.3 BODY SUPPORT: A full body harness must be worn when using SRDs. For general fall protection use, connect to the

back (dorsal) D-ring.

4.4 MAKING CONNECTIONS: Figure 12 illustrates harness and anchorage connections for SRD Fall Arrest Systems. When

using a hook to make a connection, ensure roll-out cannot occur (see Figure 5). Do not use hooks or connectors that

will not completely close over the attachment object. Do not use non-locking snap hooks. The anchorage must meet the

anchorage strength requirements stated in Table 2. Follow the manufacturer’s instructions supplied with each system

component.

4.5 OPERATION: Prior to use, inspect the SRD as described in Table 3. Figure 12 shows system connections for typical SRD

applications. Connect the SRD to a suitable anchorage or mount the SRD on the back of a Full Body Harness per the

instructions in Section 3. On anchorage connected SRDs, connect the Hook (D) or Carabiner on the Load Indicator to the

Dorsal D-Ring (A) on the Full Body Harness. On harness mounted SRDs, connect the Hook (D) or Carabiner to a suitable

anchorage. Ensure connections are compatible in size, shape, and strength. Ensure hooks are fully closed and locked.

Once attached, the worker is free to move about within the recommended working area at normal speeds. If a fall occurs

the SRD will lock and arrest the fall. Upon rescue, remove the SRD from use. When working with an SRD, always allow

the lifeline to recoil back into the device under control.

4.6 TWIN SRD INTERFACE 100% TIE-OFF: When two SRDs are mounted side-by-side on the back of a Full Body Harness,

the SRD Fall Arrest System can be used for continuous fall protection (100 % tie-off) while ascending, descending, or

moving laterally (see Figure 13). With the Lanyard Leg of one SRD attached to an anchorage point, the worker can move

to a new location, attach the unused Lanyard Leg of the other SRD to another anchorage point, and then disconnect from

the original anchorage point. The sequence is repeated until the worker reaches the desired location. Considerations for

Twin SRD 100% tie-off applications include the following:

• Never connect both SRD Lanyards to the same anchorage point (see Figure 14A).

• Connecting more than one connector into a single anchorage (ring or eye) can jeopardize compatibility of the

connection due to interaction between connectors and is not recommended.

• Connection of each SRD Lanyard to a separate anchorage point is acceptable (Figure 14B).

• Each connection location must independently support 12 kN (2,697 lbs) or be an engineered system, as with a

Horizontal Lifeline.

• Never connect more than one person at a time to the Twin SRD system (Figure 14C).

• Do not allow the Lanyards to become tangled or twisted together as this may prevent them from retracting.

• Do not allow any lanyard to pass under arms or between legs during use.

4.7 AERIAL WORK PLATFORMS: Use of the SRD on aerial work platforms is permissible, provided the following criteria are

met:

1. SRDs generally will not restrain workers from falling out of aerial work platforms or elevated working surfaces. To

restrain users from falling out of aerial work platforms, Positioning Lanyards of sufciently short lengths should be

used.

2. Aerial work platforms must have guardrails or gates at all accessible edges along their perimeter unless anchorages

for the SRDs are located overhead. The guardrail must be free of gaps that allow the lifeline to drop down through

the guardrail in the event of a fall. The edges on the top rails of all guardrails and gates over which the user might fall

must have a minimum radius of 0.3 cm (1/8 in).

3. Anchorages of appropriate strength and compatibility must always be used for securing SRDs (see Section 2).

4. Swing fall hazards may exist, especially when working near corners or out away from anchorage points. Added fall

clearance is needed where the potential for swing fall exists (see Figure 3).

5. All sharp edges which the SRD’s lifeline may contact during a fall must be eliminated or covered over. All edges the

SRD lifeline may contact in a fall must be smooth with an edge radius of 0.3 cm (1/8 in) or greater. Potential pinch

points between adjacent surfaces where the lifeline may catch during a fall must be eliminated.

4.8 HORIZONTAL SYSTEMS: In applications where the SRD is used in conjunction with a horizontal system (i.e. Horizontal

Lifeline, Horizontal I-Beams Trolley), the SRD and horizontal system components must be compatible. Horizontal systems

must be designed and installed under the supervision of a qualied engineer. Consult the horizontal system equipment

manufacturer’s instructions for details.

;

Fall Clearance values in Figure 4 are based on anchoring to a rigid, stationary anchor point and do not apply to

anchoring to a Horizontal Lifeline (HLL) system. Consult the HLL Instruction Manual and HLL Installer to determine

required Fall Clearances.

5.0 Inspection

5.1 RFID TAG: The Self-Retracting Device includes a Radio Frequency Identication (RFID) tag (see Figure 15). The RFID

tag can be used with the handheld reading device and web based portal to simplify inspection and inventory control and

provide records for your fall protection equipment. For details, contact a 3M Customer Service representative (see back

cover). Follow the instructions provided with your handheld reader, or on the web portal, to transfer your data to your

web log.

5.2 INSPECTION FREQUENCY: The Self-Retracting Device must be inspected at the intervals dened in Section 2.

Inspection procedures are described in the “Inspection & Maintenance Log” (Table 3).

;

Extreme working conditions (harsh environments, prolonged use, etc.) may require increasing the frequency of

inspections (see Table 2).

5.2 UNSAFE OR DEFECTIVE CONDITIONS: If inspection reveals an unsafe or defective condition, remove the SRD from

service immediately and discard (see Section 6).

;

Only 3M or parties authorized in writing may make repairs to this equipment.

5.3 PRODUCT LIFE: The functional life of 3M Self-Retracting Devices is determined by work conditions and maintenance. As

long as the product passes inspection criteria, it may remain in service.

6.0 MAINTENANCE, SERVICE, and STORAGE

6.1 CLEANING: Cleaning procedures for the SRD are as follows:

• Periodically clean the exterior of the SRD using water and a mild soap solution. Position the SRD so excess water can

drain out. Clean labels as required.

• Clean the Web Lifeline with water and mild soap solution. Rinse and thoroughly air dry. Do not force dry with heat.

The lifeline should be dry before allowing it to retract into the housing. An excessive buildup of dirt, paint, etc. may

prevent the lifeline from fully retracting back into the housing causing a potential free fall hazard.

6.2 SERVICE: SRDs are not repairable. If the SRD has been subjected to fall force or inspection reveals an unsafe or

defective condition, remove the SRD from service and discard (see “Disposal”).

6.3 STORAGE/TRANSPORT: Store and transport SRDs in a cool, dry, clean environment out of direct sunlight. Avoid areas

where chemical vapors may exist. Thoroughly inspect the SRD after any period of extended storage.

6.4 DISPOSAL: Dispose of the SRD if it has been subjected to fall arrest forces or inspection reveals an unsafe or defective

condition. Before disposing of the SRD, cut the lifeline in half or otherwise disable the SRD to eliminate the possibility of

inadvertent reuse.

7.0 Labels

Figure 20 illustrates labels on the the Self-Retracting Devices and their locations. All labels must be present on the SRD. Labels

must be replaced if they are not fully legible.

Table 3 – Inspection and Maintenance Log

Inspection Date: Inspected By:

Component: Inspection: (See Section 2 for Inspection Frequency)

User

Competent

Person

SRD

(Figure 16)

Inspect for loose fasteners and bent or damaged parts.

Inspect the Housing (A) for distortion, cracks, or other damage.

Inspect the Swivel (B) and Swivel Eye (C) for distortion, cracks, or other

damage. The Swivel should be attached securely to the SRL, but should pivot

freely. The Swivel Eye or Integral Connector should rotate freely in the Swivel.

The Web Lifeline (D) should pull out and retract fully without hesitation or

creating a slack line condition.

Ensure the SRD locks up when the Lifeline is jerked sharply. Lockup should be

positive with no slipping.

All labels must be present and fully legible (see Figure 20).

Inspect the entire SRD for signs of corrosion.

End Connectors

(Figure 17)

Table 2 identies the End Connectors that should be included on your

Nano-Lok SRD model. Inspect all Snap Hooks, Carabiners, Rebar Hooks,

Interfaces, etc. for signs of damage, corrosion, and proper working condition.

Where present: Gates should open, close, lock, and unlock properly, and

Locking Buttons and Locking Pins should function correctly.

Web Lifeline

(Figure 18)

Inspect webbing; material must be free of cuts (A), frays (B), or broken bers.

Check for tears, abrasions, heavy soiling (C), mold, burns (D), or discoloration.

Inspect stitching; Check for pulled or cut stitches. Broken stitches may be an

indication that the device has been impact loaded and must be removed from

service.

Energy Absorber

(Figure 19)

Verify that the integral Energy Absorber has not been activated. An open cover

or torn cover (A), webbing pulled out of the cover, torn or frayed webbing (B),

ripped stitching, etc. are indicators of an activated Energy Absorber.

Serial Number(s): Date Purchased:

Model Number: Date of First Use: