20a. Remove the paper backing from acrylic stopper (SS), then
properly align the acrylic stopper into the cut-out on the acrylic
stopper template on the front of the top panel (A). Press down
on the acrylic stopper to help adhesion.
20b. At the back of top panel (A), grip the head of plastic tack with
pliers, with twisting motion pull tack loose to remove the acrylic
stopper template.
NOTE: You must install the acrylic TV stopper to prevent
TV from tipping when placing your at panel television on
the top panel.
B
A
Hardware Used
Acrylic Stopper
x 1
SS
SS
19. Using the pilot holes as a guide, align and attach L-shaped metal
braces (LL) to the bottom panel (B) by screwing one washer
head screw (EE) in each.
Hardware Used
Washer Head Screw
L-shaped Metal Brace
x 2
x 2
EE
EE
LL
LL
The rubber bumper is
against the rebox
19
21
20
Connector
Wooden stud
Short
Screw
Metal Bracket
Long Screw
Floor
Leveler
Wall
Wall
CARE AND MAINTENANCE
CARING FOR WOOD FURNITURE
CLEANING THE FIREPLACE TRIM
A touch-up pen has been provided to minimize the small nicks or scratches that may occur during assembly or shipping.
To clean and care for your furniture:
• Use a soft, clean cloth that will not scratch the surface when dusting.
• Use of furniture polishes is not necessary. Should you choose to use polishes, test rst in an inconspicuous area.
• Using solvents of any kind on your furniture may damage the nish.
• Never use water to clean your furniture as it may cause damage to the nish.
• Always use coasters under beverage glasses and owerpots.
• Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing.
• Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting
within the furniture nish.
• Stains or marks from crayons or ink markers will be dicult to remove.
• In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional
to repair your furniture.
• Check bolts/screws periodically and tighten them if necessary.
• It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause
fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage
the nish.
• Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance
your furniture as it ages.
Clean the metal trim using a soft cloth, slightly dampened with citrus oil based product and bu with a clean soft cloth. DO NOT
use brass polish or household cleaners as these products will damage the metal trim. Citrus oil based products can be obtained
at supermarkets or hardware stores.
This product is warranted to the original purchaser. If there is a failure in this unit due to defects in materials or workmanship,
the manufacturer will repair or replace this item at our discretion without charge. Warranty is void if product has been assembled
incorrectly, misused, abused by overloading, altered in any way or damaged due to accident. This warranty is not transferable
and does not cover chipping, aking, scratches, rust, dents, or other damages to the surfaces of this product. Responsibility
of the manufacturer is limited to repair or replacement of this product. The manufacturer is not responsible for consequential,
incidental, or other damages or losses resulting from product failure.
This warranty is in lieu of all other expressed warranties. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you. This warranty gives you specic legal rights and you may
have other rights which vary from state to state.
ONE-YEAR LIMITED WARRANTY
13
ASSEMBLY INSTRUCTIONS
NOTE: Young children can be seriously injured by tipping furniture. You
must install the tipping restraint hardware with the unit to prevent the unit
from tipping, causing any accidents or damage. The tipping restraints are
intended only as a deterrent, they are not a substitute for proper adult
supervision. The tipping restraints are not earthquake restraints. If you
wish to add the extra security of earthquake restraints, they must be
purchased and installed separately.
19a. With assistance, position the assembled replace console at the desired
location against a wall. In case of uneven oor, oor levelers are provided
at the bottom of the mantel. If necessary, adjust the oor levelers by hand
to correct tilting and/or level the doors, until the unit is level.
19b. Follow the instructions printed on the plastic bag containing the tipping
hardware to attach the tip-over restraint to the unit and the wall.
19c. Connect the replace to the power transformer. Follow the operating
manual for the electric replace insert to control your replace.
Hardware Used
Tipping Restraint
Hardware Kit
x 2
WW
Installing the tipping restraint hardware
12