Transcripción de documentos

Bul. 140G/140MG DIR 1000479R0621 Version 01 - 140G-M-EOP_ , 140G-M-ECOP_ Stored energy operating mechanism for 140G-M Comando a motore ad accumulo di energia Motorantrieb mit energiespeicherung Commande par moteur a accumulation d’energie Mando a motor con acumulacion de energia Installation - Installazione - Instalación Instalação - Rated service voltage 24 Vdc Tensione nominale di impiego 48...60 Vdc 110...125 Vac/Vdc Bemessungsbetriebsspannung 220...250 Vac-Vdc Tension assignée de service 380 Vac Tensiòn nominal de servicio Inrush power consumption Potenza spunto Leistungsaufnahme beim Anzug 300 VA-W Consommation à l’appel Potencia absorbida al arranque Continuous service input Potenza in servizio 150 VA-W Leistungsaufnahme bei Dauerbetrieb Consommation (service continu) Potencia absorbida en servicio permanente WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements). AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E). WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen Sie die Anforderungen nach NFPA70E). AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E). ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E). ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E). Operation time Tempo di manovra Schaltzeit Temps de manoeuvre OFF Riarmo / Reset Rückstellung Reset / Rearme < 0.1 s 3s 5s Tiempo de maniobra 警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく ださい。適切なケース内に取付けてください。また、汚染物質がないことを 確認してください。（NFPA70Eの要件に従ってください） Control impulse minimum time 0,15s Durata minima impulso di comando 0,15s Mindestdauer des Steuerimpulses 0,15 s Durée minimale de l'impulsion de commande 0,15s 警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备 箱内。防止接触污染物。符合NFPA70E要求） 5 Screw LENGTH 25 mm (0.98") ON dia. 5 4 2 3 1 Screw LENGTH 20 mm (0.79") - Only for 140G-M-ECOP - Solo per 140G-M-ECOP - Nur für 140G-M-ECOP - Uniquement 140G-M-ECOP - Sólo para 140G-M-ECOP DIR 1000479R0621 Version 01 M M4 Label Escutcheon  1 2 CLACK 3 4 - Only for 140G-M-ECOP - Solo per 140G-M-ECOP - Nur für 140G-M-ECOP - Uniquement 140G-M-ECOP - Sólo para 140G-M-ECOP DIR 1000479R0621 Version 01 (2)  5 2 1 - Do not insert when undervoltage/shunt release is mounted - Non inserire nel caso sia montata la bobina di apertura/minima - Nicht einschalten, wenn die undervoltage/shunt release montiert sind - Ne pas insérer au cas où la undervoltage/shunt release sont montées - No introducir en caso de que esté montada la undervoltage/shunt release 6 3 - For local/remote indication only - Solo per la segnalazione elettrica - Nur für elektrische Meldung - Uniquement pour signalisation électrique - Sólo para se DIR 1000479R0621 Version 01 (3)  7 8 ONLY FOR 140G-M-ECOP 10 ONLY FOR 140G-M-ECOP 5 4 - Do not insert when undervoltage/shunt release is mounted - Non inserire nel caso sia montata la bobina di apertura/minima - Nicht einschalten, wenn die undervoltage/shunt release montiert sind - Ne pas insérer au cas où la undervoltage/shunt release sont montées - No introducir en caso de que esté montada la undervoltage/shunt release 9 ONLY FOR 140G-M-ECOP 4.4 lb-in 0.5 Nm DIR 1000479R0621 Version 01 (4)  11 12 ONLY FOR 140G-M-ECOP 13 14 LENGTH 25 mm (0.98") DIR 1000479R0621 Version 01 dia. 5 9.7 lb-in 1.1 Nm (5) ONLY FOR 140G-M-ECOP ONLY FOR 140G-M-ECOP  16 15 DISCHARGED 17 PULL PUSH PULL DIR 1000479R0621 Version 01 (6)  18 LENGTH 20 mm (0.79") M M4 9.7 lb-in 1.1 Nm 19 20 9.7 lb-in 1.1 Nm DIR 1000479R0621 Version 01 (7) ONLY FOR 140G-M-ECOP  21 22 23 24 ONLY FOR DISASSEMBLING In=...A APPLY LABEL 9.7 lb-in 1.1 Nm DIR 1000479R0621 Version 01 (8)  25 Operating mode: Manual I: ON I: ON discharged springs SNT / UVR / EL SNT release tripping O: OFF Operating mode: Auto OFF SNT / UVR / EL SNT pushbutton on the motor release tripping ON pushbutton discharged springs O: OFF on the motor recharge discharged springs OFF ON pushbutton pushbutton remotely remotely OFF pushbutton the springs O: OFF discharged springs remotely charged springs O: OFF 26 charged springs 27 PUSH L UA AN M AU TO A = Y = B C PULL X X Y A max #3 from dia. 0.16" to dia. 0.24" max #3 from ø 4 mm to ø 6 mm DIR 1000479R0621 Version 01 B C 5.84" 5.94" 2.98" WITH ESCUTCHEON 148.5 mm 151 mm 75.75 mm 5.59" 5.59" 2.80" WITHOUT ESCUTCHEON 142 mm 142 mm 71.25 mm (9)  28 29 + ~ LEGEND SO SC U1 54 C11 C11 A1 A1 54 U1 H CONTROL POWER STORED ENERGY MOTOR OPERATOR MANUAL S3 140G-K-ECOP_ 140G-K-EOP_ LEGENDA ZEICHENERKLÄRUNG LÉGENDE LEYENDA H H H H H H = Signal lamp = Lampada di segnalazione = Signallampe = Voyant lumineux de signalisation = Lámpara de señalación = 信号指⽰灯 SO SO SO SO SO SO = Pushbutton or contact for opening the circuit-breaker = Pulsante o contatto per l'apertura dell'interruttore = Taster oder Schalter zum Öffnen des Leistungsschalters = Bouton-poussoir ou contact pour l’ouverture du disjoncteur = Pulsador o contacto para la apertura del interruptor = 分断断路器的按钮或触头 SC SC SC SC SC SC = Button or contact for switch closing = Pulsante o contatto per la chiusura dell'interruttore = Drucktaster oder Kontakt für Schließen des Schalters = Poussoir ou contact pour fermer le disjoncteur = Pulsador o contacto para el cierre del interruptor = 闭合断路器的按钮或触头 S3 S3 S3 S3 S3 S3 = Change-over contact for electrical signalling of local/remote selector status = Contatto di scambio per la segnalazione elettrica di stato del selettore locale/remoto = Umschalter für die elektrische Zustandsmeldung des lokalen /fernen Wahlschalters = Contact inverseur pour signalisation électrique de etat de local/ déporté sélecteur = Contacto conmutado para señalización eléctrica de estado de local/remoto selector = 显⽰⼿动/⾃动（遥控）状态电⽓信号的辅助触头 U2 Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page Publication 140G-IN032B-MU-P - April 2016 DIR 1000479R0621 Version 01 (L7944) - B0822 Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.