nue with the steam delivery and suction, pres-
sing the steam trigger on the handle, and the
suction button on the appliance (33).
The combined use of steam and suction al-
lows the most efficient sanitising of the surfa-
ce, dissolving dirt, eliminating grease, germs
and mites, and above all allows drying of the
surfaces.
In this position, it is also possible to vacuum
small quantities of liquids and dry the floor.
3.6 To clean using steam alone, it is possible
to use the abrasive action of the cloth sup-
plied (L). Attach it to the universal brush (B)
before starting to clean the surface.
4. CLEANING DELICATE FLOORS
(wooden, stone, waxed surfaces, etc.)
Make sure that you have prepared the ap-
pliance following the instructions listed in
Chapter 1 and connect the accessories listed
in Chapter 2.
4.1 Lock the two extension tubes (C) onto the
handle (A) (15-16).
4.2 For suction only, connect the universal
brush (B) (18) with the bristle frame (B1)(19-
20-21) and press the suction button on the
appliance (29) to proceed with the cleaning
operations.
4.3 For steam cleaning and suction attach the
rug/carpet frame (B3) to the universal brush
(B)(19-20-21). Attach the cloth supplied (L) to
the universal brush (B) (22).
4.4 Turn on the boiler by pressing the boiler
button and adjust the strength of the steam
using the steam adjustment dial (29-30-31) (to
turn the boiler off press the boiler button
again); for this type of surface we recommend
steam level 1/2
. The steam indicator light ( )
comes on, and then turns off when the correct
temperature has been reached.
4.5 Deactivate the steam lock (32) and conti-
nue with the steam delivery and suction, pres-
sing the steam trigger on the handle (33), and
the suction button on the appliance (28). The
cloth will remove the dirt and the steam with
sanitise the surface.
5. CLEANING RUGS AND CARPETS
Make sure that you have prepared the ap-
pliance following the instructions listed in
Chapter 1 and connect the accessories listed
in Chapter 2.
5.1 Lock the two extension tubes (C) onto the
handle (A)(15-16).
5.2 Connect the universal brush (B)(18) to the
rug/carpet frame (B3) (19-20-21).
5.3 For suction only, press the suction button
on the appliance to proceed with cleaning
(28).
5.4 For steam cleaning and suctionturn on the
boiler by pressing the boiler button (29) and
adjust the strength of the steam using the
steam adjustment dial (31)(to turn the boiler
off press the boiler button again (29)); for this
type of surface we recommend
steam level 3
.
The steam indicator light ( ) comes on, and
then turns off when the correct temperature
has been reached.
5.5 Deactivate the steam lock (32) and conti-
nue with the steam delivery and suction, pres-
sing the steam trigger on the handle (33), and
the suction button on the appliance (28).
5.6 It is possible to use the suction and steam
features either together or by alternating
them, activating both as described in the pre-
vious points.
Combined use of steam and suction allows
the most efficient sanitising of the surface,
dissolving dirt and removing grease, germs
and mites; it allows brightens the colour of fi-
bres and dries surfaces more quickly.
For safety reasons, engage the steam lock
on the handle during vacuuming.
WARNING: For additional safety, before
using the appliance on delicate surfaces and
those treated with with special oil, wax, etc.
test steam delivery on a hidden part and lea-
ve the steamed part to dry to ensure that no
changes in colour or deformation have oc-
curred.
Before removing the cloth from the brush,
wait a few minutes to allowthe cloth to cool.
WARNING: Before cleaning fabrics with
steam, consult the manufacturer’s instructions
and always carry out a test on a hidden part or
on a sample of the material. Allow the steamed
part to dry to make sure that no changes in co-
lour or deformations have occurred.
For safety reasons, engage the steam lock
on the handle during vacuuming.
Before using the appliance on delicate surfa-
ces, ensure that the part in contact with the
surface is free from foreign bodies that
could cause scratches.
Before removing the cloth from the brush,
wait a few minutes to allow the cloth to cool.
To avoid any dirt in the dirt collector causing
bad smells, we recommend emptying and
cleaning after every use according to the
methods described in Chapter 15.
ITALIANOENGLISH
| 38 |