Andersen A-Series 2-Panel Assembled Gliding Patio Doors Guía de instalación

Marca: Andersen

Modelo: A-Series 2-Panel Assembled Gliding Patio Doors

Tipo: Guía de instalación

9014018 BF Revised 01/25/23

Installation Guide/Guía de instalación

for Andersen® A-Series 2-Panel Assembled Gliding Patio Doors

para puertas corredizas para patio ensambladas de 2 paneles de la serie A de Andersen®

• House Wrap Tape / Cinta para sellar las uniones del house wrap exterior

• Drip Cap (full width) / Tapa de goteo (ancho completo)

• Extension Jambs (optional) / Jambas de extensión (opcional)

• Low Expanding Foam / Espuma de baja expansión

• Shims (waterproof) / Cuñas (impermeables)

• Foam Backer Rod / Varilla de respaldo de espuma

• Sealant / Sellador

• Staples / Grapas

Supplies Needed / Suministros necesarios

Formable Self-adhering Sill Flashing*

Flashing para riel auto-adherente moldeable*

Flashing* / Flashing*

or*

o bien*

Parts Included / Partes incluidas

(1) Instruction Guide /

Guía de instrucciones

(1) Patio Door Unit /

Unidad de puerta de patio

(1) Screw Pack /

Paquete de tornillos

(1) Hardware Carton / Caja de cartón con herrajes

Tools Needed / Herramientas necesarias

• Safety glasses / Gafas de seguridad

• Hammer / Martillo

• Tape measure / Cinta métrica

• Level / Nivel

• Utility knife / Cuchilla de uso general

• Putty Knife / Espátula

• Staple Gun / Pistola engrapadora

• Phillips Screwdriver / Destornillador Phillips

• Flat Blade Screwdriver / Destornillador de punta plana

• Drill/Driver / Taladro/destornillador

• Diagonal Cutting Pliers / Pinzas de corte diagonal

• Caulk Gun / Pistola para calafatear

* Or other ashing method/material recommended by

a contractor or architect. Unit anges do not take

the place of ashing.

* O bien otro método/material de ashing recomendado

por el contratista o arquitecto. Las bridas de la unidad

no reemplazan el ashing.

Liquid ashing

recommended on

concrete slab.

Se recomienda el uso

de ashing líquido en

losa de concreto.

Read these instructions before starting procedure. For additional information visit www.andersenwindows.com. For questions call 1-888-888-7020.

Lea estas instrucciones antes de iniciar el procedimiento. Para obtener información adicional, visite www.andersenwindows.com

Si tiene alguna pregunta, llame al 1-888-888-7020.

▶Parts included may exceed quantity required for your particular installation.

Las partes que se incluyen pueden exceder la cantidad requerida para su instalación en particular.

▶Do not remove packing clips from door until instructed.

No retire los sujetadores de embalaje de la puerta hasta que se le indique.

9014018

(4) #8-32 x 1-1/8" Machine Screw

(4) tornillos para metales No. 8-32 x 1-1/8"

Screw Pack Contents:

Contenido del paquete de tornillos:

(12) #10 x 1" Flat Head Screws

(12) tornillos de cabeza plana No. 10 x 1"

(16) #10 x 3" Phillips Flat Head Yellow Zinc Screws

(16) Tornillos de cinc amarillos de cabeza plana

Phillips n.º 10 x 3"

(6) #10 x 3" Phillips Flat Head Gray Screws

(6) tornillos de cabeza plana Phillips No. 10 x 3"

de color gris

(3) Sill Clip

(3) Sujetador de riel

(2) Flange Gasket

(2) Empaque de la brida

(7) Fastener Plugs

(7) Tapones del sujetador

Not all fasteners may be used

Es posible que no se utilicen todos los sujetadores

(4) #8-32 x 7/8" Machine Screw

Tornillos para metales No. 8-32 x 7/8"

(2) #10 x 3" Security Screw

Tornillo de seguridad No. 10 x 3"

(1) Lock

Cerrojo (1) 2- or 3-Panel Receiver

Receptor de 2 o 3

paneles

(2) #10 x 3" Stainless Steel Screw

Tornillo de acero inoxidable No. 10 x 3"

(1) #10 x 4" Security Screw

Tornillo de seguridad No. 10 x 4"

or/

o bien

Hardware Carton Contents:

Contenidos de la caja de cartón con herrajes:

(2) #10-32 x 1-1/4" Machine Screw

Tornillo para metales No. 10-32 x 1-1/4"

For Flush Mount Hardware/

Para herrajes de montaje embutido

For Reachout Lock Hardware/

Para herrajes de cerrojo de alcance

(1) Receiver

Receptor

(1) Lock

Cerrojo

(1) Receiver

Position

Template

Plantilla de

posición del

receptor

(1) Bezel

Bisel

DraftDraft

Procedure and

Product Information

IMPORTANT

Important Safety and

Product Information

for Andersen® Windows and Doors

This is the Safety Alert Symbol used to alert you to

potential injury hazards. Obey all safety messages that

follow this symbol to avoid possible injury or death.

Signal Word and Consequence

Major Injury/Death

WARNING

COULD

Result in: Minor Injury

CAUTION

COULD

Result in:

Product or Property

Damage

NOTICE

COULD

Result in:

· Leave this installation instruction with the home/building owner.

· For additional support or help please go to: andersenwindows.com and visit our Help Center.

· To congure installation instructions go to: andersenwindows.com/installation

Handling Installation

· Use caution when working at elevated heights and

around window and door openings. Follow the

manufacturers’ instructions for ladders and scaffolding.

Failure to do so could result in injury or death.

· Support window or door in opening at all times until

fully fastened. Failure to do so could result in window or

door falling out causing injury, property or product

damage.

· Windows and doors have small parts (e.g. hole plugs,

operator spline caps, fasteners, etc.). Small parts if

swallowed could pose a choking hazard to young

children. Dispose of unused, loose, or easily removed

small parts. Failure to do so could result in injury.

· Windows and doors can be heavy. Use safe lifting

techniques and a reasonable number of people with

enough strength to lift, carry, and install window and

door products. Heavier windows and doors will require

mechanical assistance. Failure to do so could result in

injury, product or property damage.

· DO NOT lift or carry window or door by the exterior

trim or extension jambs. Doing so could result in injury,

product or property damage.

· Windows, doors, and installation components can

have sharp edges. Wear protective equipment when

handling. Failure to do so could result in injury.

· DO NOT drag, rock, cartwheel, or walk windows,

doors, sash, or panels across the floor. Doing so could

result in product or property damage.

Tools

· Follow manufacturers’ instructions for hand and power tools. Always wear safety glasses. Failure to do so could result in

injury, product or property damage.

❚ Tools

❚ Handling

❚ Installation

❚ Sealing

❚ Fastening

❚ Finishing

Safety and Product Information Index

❚ Glass

❚ Protective Film

❚ Cleaning

❚ Use/Operation

❚ Joining

❚ Product Information

Read this Important Safety and Product

Information completely before starting.

WARNING

WARNING WARNING

▶Para obtener la versión en español de Información importante sobre productos y seguridad, visite: andersenwindows.com

DraftDraft

NOTICE

· Andersen head ashing and installation anges DO

NOT take the place of window and door ashing tape or

liquid ashing. Window or door must be properly ashed

and sealed with a material compatible sealant for

protection against water and air inltration.

Failure to do

so could result in product or property damage.

· DO NOT set window or door directly on installation

ange. Doing so could affect product performance, and

could result in product or property damage.

· DO NOT set window directly on sill plate. Elevate

window with shims under the side jambs. Failure to do

so could affect operation and product performance, and

could result in product damage.

· Window or door must be properly shimmed. Failure to

do so could affect operation and product performance,

and could result in product damage.

· A continuous full perimeter interior seal between

window or door frame and opening is required. Failure to

do so will affect product performance, and could result

in product or property damage.

· Protect window and door sills during installation and

throughout construction. Failure to do so could result in

product damage.

· DO NOT remove window or door packaging material until

instructed to do so. Doing so could result in product damage.

Installation (Continued)

NOTICE

· Use masonry screws when fastening directly into

masonry or through a buck into masonry. Failure to do

so could affect product performance, and could result in

product or property damage.

· DO NOT over drive screws or nails. Doing so could

result in product damage.

· Fasteners must be attached to a structural framing

member. Failure to do so will reduce the structural

performance to less than published values and could

affect product performance, and could result in product

or property damage.

Fastening

· Metal fasteners and components could corrode when

exposed to preservative-treated or fire-retardant treated

lumber. Use approved fasteners and components to

fasten window or door. Failure to do so could cause a

failure resulting in injury, product or property damage.

· Fastener must attach to a structural framing member

with a 1-1/2" minimum fastener embedment. Failure to

do so could result in injury, product or property damage.

· DO NOT remove screws that attach installation clips or

gusset plates to window or door frames. Doing so could

result in injury, product or property damage.

Sealing

NOTICE

CAUTION

· Follow instructions of foam, sealant, and flashing

manufacturers regarding safety, material application,

compatibility, and periodic maintenance for continued

weather resistance of their products. Failure to do so

could result in injury, product or property damage.

Finishing

NOTICE

· DO NOT stain or paint weatherstrip, vinyl, glass, or

hardware. Doing so could result in product damage.

· Read and follow nish manufacturer's instructions and

safety information. Failure to do so could result in

product damage.

· DO NOT over load brush with stain or paint when

nishing. Doing so could allow nish to wick between

glass stop or grille, and glass.

WARNING

· Clean and prepare surfaces receiving sealant following

sealant manufacturer's instructions. Failure to do so could

result in water inltration causing product or property damage.

· DO NOT use abrasive cleaners or solvents when

cleaning Fibrex® material. Doing so could result in

product damage. Go to andersenwindows.com for a list

of recommended cleaners.

DraftDraft

NOTICE

Glass

· Unless specifically ordered, Andersen windows are not

equipped with safety glass, and if broken, could

fragment causing injury. Many laws and building codes

require safety glass in locations adjacent to or near

doors. Andersen windows are available with safety glass

that could reduce the likelihood of injury when broken.

Information on safety glass is available from your local

Andersen dealer.

· Tempered or laminated safety glass is not standard for

windows and must be special ordered. Check local

building codes for required locations. Failure to do so

could result in injury, product or property damage.

· DO NOT place suction grips over film

seams on glass. Suction grips will not

hold if placed over lm seam to lift or

move window or door. Window or door

will fall and could result in injury,

product or property damage.

· DO NOT remove any

protective film near

flammable materials.

Static charge created

when removing film

can ignite flammable

materials or cause a

shock. Doing so could result in injury, product or

property damage. See warning label on glass.

· Dispose of protective film immediately after

removing. Failure to do so could pose a suffocation

hazard to children.

NOTICE

· DO NOT remove protective lm from glass until after

construction is completed. Doing so could allow glass to

be damaged.

· Remove protective film from non-glass components

immediately after installation. Failure to do so could

result in product damage.

NOTICE

Cleaning

Protective FilmFinishing (Continued)

· Finish all wood surfaces immediately after

installation. Unnished wood will deteriorate, discolor,

and could bow or split. Some

surfaces are hidden from view.

· Some products are shipped

unassembled, and it may be

more convenient to finish

wood surfaces for these

products prior to

assembly and

installation.

WARNING

· Acid solutions used for cleaning masonry or concrete

will damage all components of window or doors. Protect

window or door and follow cleaning product

manufacturer's instructions. If acid contacts window or

door, wash all surfaces immediately with clean water.

· DO NOT use or apply solvents, abrasives, harsh

chemicals or cleaners to window or door components.

Doing so will result in product damage.

For a list of recommended cleaners go

to: andersenwindows.com

· DO NOT use metal razor blades to

clean glass surface. Glass damage

could result.

· DO NOT apply any type of film to insulating glass.

Doing so could cause thermal stress conditions and

result in glass damage. Shading devices (e.g. insulated

coverings, shutters, etc.) could also cause thermal

stress and condensation causing deterioration of

windows or doors.

· DO NOT use sealants on exterior or

interior glass surface.

NOTICE

DraftDraft

Joining

IMPORTANT

· Buildings constructed prior to 1978 could contain lead

paint which could be disturbed during window or door

replacement. For more information on proper management

of lead paint, go to: www.epa.gov/lead

· Instructions may not be right for all installations due to

building design, construction materials, or methods used

and/or building or site conditions. Consult a contractor or

architect for recommendations.

· Installation flanges may need to be removed for some

installations. (e.g. masonry, replacement), or where exterior

finish is already applied (e.g. siding, brick veneer, stucco).

· Installation ange on the window or door alone will not

properly ash and seal the window or door.

· DO NOT remove band, plastic ties, or packing clips from

window or door until instructed.

· DO NOT remove performance (NFRC) label until after nal

inspection. Doing so could delay nal inspection and

sign-off by the code ofcial.

· Check with your local building code ofcial to identify and

conrm compliance with local building code requirements.

· Contact local authorities or waste management company

for proper recycling and disposal instructions for removed

window or door.

· For cleaning instructions for window and door components

go to: andersenwindows.com.

· During construction protect products from construction

debris, harsh chemical such as brick wash, roof runoff, and

cement/masonry which can cause damage to window and

door products.

· Protective lm is not present on all windows or doors.

Protective lm is not a substitute for masking.

· Remove protective film from glass within six (6) months of

installation and when temperature is above 32° F.

· Remove protective lm by peeling from seam or corner.

Use a plastic scraper to start if needed.

· Extension jambs can be factory applied on some windows

or eld applied prior to installation. DO NOT apply extension

jambs prior to window or door installation that will be

fastened with installation clips. Doing so could prevent

access to installation clips for fastening.

· For extension jamb application refer to

instructions included with part(s) or go to:

andersenwindows.com

· Use painters masking tape for protecting

products during construction. Avoid using

duct or packaging tapes.

Use/Operation

· DO NOT stand in front of or near windows or doors

during a storm. Doing so could result in injury.

Accessories such as grilles, art glass, and insect

screens could dislodge and become airborne if window

or door is impacted by wind-borne debris from severe

storms or hurricane strength winds. In the event of a

storm, remove all accessories from windows or doors

and move to a safe location.

· DO NOT install air conditioner in

window. Doing so could result in

injury, product or property damage.

· Wind load brackets

must be flipped out

when not tilting or

cleaning. If wind load

brackets are not flipped

out, window could blow

in resulting in potential

injury and/or product

damage.

· DO NOT attach objects or accessories to window or

door except Andersen® products specifically designed

for the window or door. Doing so could result in injury,

product or property damage.

Product and General Information

· DO NOT join any window or door, horizontally or

vertically, to any window or door not designed for

joining. Doing so could result in injury, product or

property damage.

· Joined windows or doors must be individually

supported in the opening. Failure to do so could affect

operation and product performance, and could result in

product or property damage.

CAUTION

WARNING

Flipped Out Flipped In

Interior

Exterior

Cut opening in house wrap.

Corte una abertura en el house wrap.

Fold in and staple.

Doble y engrape.

Level

Nivel

Tape Measure

Cinta métrica

Utility Knife

Cuchilla de

uso general

Tape

Cinta

Exposed Sheathing

Recubrimiento expuesto

9014018

Width of ashing

Ancho del ashing.

45°

Cut and create top ap from house wrap.

Corte y cree una pestaña superior con el house wrap.

Fold ap up and tape.

Doble la pestaña hacia arriba y coloque cinta.

Tape Measure

Cinta métrica

Check opening size. Allow for ashing thickness.

Verique el tamaño de la abertura. Tenga en cuenta el espesor del

ashing.

Check plumb, level, square. Diagonals must be within 1/8".

Verique la plomada, el nivel y la cuadratura. Las diagonales deben

estar dentro de 1/8".

Exterior

9014018

2-3"

Sill Flashing

Flashing para riel

Apply using rm

pressure.

Aplique presionando

rmemente.

Apply ashing at sill (liquid ashing recommended on concrete slab).

Aplique el ashing en el riel inferior (se recomienda el uso de ashing líquido en

losa de concreto).

Liquid ashing

recommended on

concrete slab.

Se recomienda

el uso de ashing

líquido en losa de

concreto.

Apply formable ashing. Make sure there are no wrinkles or voids. Failure

to do so may result in product /property damage.

Aplique el ashing moldeable. Asegúrese de que no haya arrugas ni vacíos.

De no hacerlo así, podrían producirse daños al producto/propiedad.

NOTICE / AVISO

J-roller

Rodillo tipo J

Interior

9014018

Windows and doors can be heavy. Use safe lifting techniques

and a reasonable number of people with enough strength to

lift, carry and install window and door products to avoid injury

and/or product damage.

Las ventanas y puertas pueden ser pesadas. Utilice técnicas

seguras de levantamiento de peso y un número razonable de

personas con suciente fuerza para levantar, cargar e instalar

los productos de puertas y ventanas, a n de evitar lesiones y/o

daños al producto.

Banding Tape

Cinta Hardware Carton

Caja de cartón

con herrajes

Remove hardware carton and save for later installation. Remove corner protectors and discard. Do not remove banding tape.

Retire la caja de cartón con herrajes y guárdela para una instalación posterior. Retire los protectores de esquinas y deséchelos. Noretire la cinta.

Exterior

Top/Sides

Laterales/parte

superior

Sill

Riel

Apply sealant at top and sides. Apply three beads sealant at sill and

liberally in bottom corners.

Aplique el sellador en la parte superior y en los laterales. Aplique tres

listones de sellador en el riel y libremente en la esquina inferior.

3/8" Bead

Sealant

Sellador

para listones

de 3/8"

Caulk Gun

Pistola para

calafatear

1/2"

4-1/4"

1-1/4"

1/4"

If using remodel bracket, go to instruction guide

included with remodel bracket and follow instructions.

Si va a utilizar el soporte de remodelación, consulte la

guía de instrucciones incluida con el soporte y siga las

instrucciones.

Tape corners. If using remodel bracket, go to instruction guide

included with remodel bracket and follow instructions.

Encinte las esquinas. Si va a utilizar el soporte de remodelación,

consulte la guía de instrucciones incluida con el soporte y siga las

instrucciones.

WARNING / ADVERTENCIA

IMPORTANT/IMPORTANTE

Tape

Cinta

Tape

Cinta

Snap installation anges into position at top and sides. Pull rings to remove stationary jamb trim. Save stationary jamb trim for reinstallation.

Presione las bridas de instalación en posición en la parte superior y en los laterales. Retire los aros para extraer el contramarco de jamba

estacionaria. Guarde el contramarco de jamba estacionaria para volver a instalarlo.

Interior

Exterior

9014018

Remove packaging handles and discard. Do not reinstall screws.

Retire las manijas de embalaje y deséchelas. No vuelva ainstalar los

tornillos.

Apply corner gasket. Apply sealant as shown.

Aplique la junta de esquina. Aplique sellador como se muestra.

Installation Flange

Brida de instalación

Drill/Driver

Taladro/destornillador

Packaging Handle

Manija de embalaje

Corner Gasket

Junta de esquina

Rings

Aros

Stationary Jamb Trim

Contramarco de

jamba estacionaria

Operating Jamb

Jamba operativa

Stationary Jamb

Jamba estacionaria

Apply sealant

to both sides.

Aplique selldor

en ambos

laterales.

Apply sealant to

both sides.

Aplique sellador

en ambos

laterales.

Exterior

Interior

Center door in opening at sill and tip door into opening.

Centre la puerta en la abertura del riel e incline la puerta dentro de la

abertura.

Support door in rough opening at all times until

secured. Failure to do so may result in door falling

out causing injury, property, and/or product damage.

Sostenga siempre la puerta en la abertura no

acabada hasta que esté asegurada. De no hacerlo, la

puerta se puede caer y provocar lesiones, daños al

producto y/o a la propiedad.

9014018

Level

Nivel

Tape Measure

Cinta métrica

Check plumb, level and square. Adjust shims as needed until diagonal measurements are within 1/8". Secure stationary side jamb. Do not

fully tighten. Cut plastic tie on back side of operating jamb.

Verique la plomada, el nivel y la cuadratura. Ajuste las cuñas según sea necesario hasta que las medidas diagonales estén entre las 1/8". Ajuste la

jamba estacionaria. No ajuste completamente. Corte la unión plástica en la parte posterior de la jamba operativa.

Operating Jamb

Jamba operativa

Stationary Jamb

Jamba

estacionaria

Shim behind each fastener hole. Shims must be tight to installation

ange.

Coloque cuñas detrás de cada oricio del sujetador. Las cuñas deben

estar ajustadas a la brida de instalación.

WARNING / ADVERTENCIA

Diagonal Cutting Pliers

Pinzas de corte diagonal

Plastic Tie

Unión plástica

Drill/Driver

Taladro/

destornillador

#10 x 3" Yellow Zinc Screw

Tornillo de cinc amarillo

n.º 10 x 3"

Shim

Cuña

Installation Flange

Brida de instalación

Fastener Hole

Oricio del sujetador

Interior

9014018

Remove adjustment hole caps. Insert at blade screwdriver into socket and turn clockwise to raise panel and remove both sill pads. Replace

adjustment hole caps.

Retire los tapones de oricios de ajuste. Coloque un destornillador de punta plana dentro del adaptador y gire hacia la derecha para levantar el

panel y retirar las almohadillas del riel. Retire los tapones de oricios de ajuste.

Adjustment hole caps are small parts. And if

swallowed, could pose a choking hazard to young

children. Replace caps after making adjustments.

Las tapas para oricios de ajuste son piezas

pequeñas. En caso de ingesta, pueden representar

un riesgo de asxia para niños pequeños. Vuelva a

colocar los tapones después de realizar los ajustes.

Open operating panel. Shim and secure operating jamb. Do not fully

tighten.

Abra el panel operativo. Coloque las cuñas y asegure la jamba

operativa. No ajuste completamente.

Operating Jamb

Jamba operativa

Operating Panel

Panel operativo

Banding Tape

Cinta

WARNING / ADVERTENCIA Adjustment Hole Cap

Tapón para oricio

de ajuste

Sill Pad (2)

Almohadilla

del riel (2)

Flat Blade Screwdriver

Destornillador de punta plana

Drill/Driver

Taladro/

destornillador

#10 x 3" Yellow Zinc Screw

Tornillo de cinc amarillo

n.º 10 x 3"

Interior

9014018

Shim near screw location at head jamb and secure.

Coloque las cuñas cerca de la ubicación de los tornillos en la jamba

de cabecera y asegure.

Trim shims ush and remove banding.

Recorte las cuñas al ras y retire el encintado.

Banding

Cintas sujetadoras

Shim

Cuña

Utility Knife

Cuchilla de

uso general

Interior

Check plumb, level and square. Adjust shims as needed until diagonal measurements are

within 1/8" and fully tighten screws at sides. Cut banding tape, if necessary, to square.

Verique la plomada, el nivel y la cuadratura. Ajuste las cuñas según sea necesario hasta

que las medidas diagonales estén entre los 1/8" y ajuste completamente los tornillos en

los laterales. Corte la unión plástica, si fuera necesario, para niverla a escuadra.

Level

Nivel

Tape Measure

Cinta métrica

#10 x 3" Grey Screw

Tornillo No. 10 x 3"

de color gris

Drill/Driver

Taladro/

destornillador

Exterior

9014018

Place drip cap (full width) in sealant.

Coloque la tapa de goteo (ancho completo) en el sellador.

Seal top and sides only. Quickly go to next step.

Selle únicamente los laterales y la parte superior. Pase rápidamente

al siguiente paso.

Interior

Exterior

Apply fastener plugs at all hole locations on operating side jamb.

Coloque tapones del sujetador en todas las ubicaciones de los

oricios en la jamba lateral operativa.

Apply ashing at sides, overlapping sill ashing.

Aplique ashing en los laterales, superponiéndolo sobre el ashing

para riel.

Flashing

Fastener plugs are small parts and, if swallowed,

could pose a choking hazard to young children.

Remove and dispose of any loose or easily removed

fastener plugs.

Los tapones del sujetador son partes pequeñas

que, en caso de ingesta, pueden representar un

riesgo de asxia para niños pequeños. Retire y

deseche todos los tapones del sujetador sueltos o

que se puedan quitar fácilmente.

Fastener Plug

Tapón del sujetador

WARNING / ADVERTENCIA

Drip Cap (full width)

Tapa de goteo

(ancho total)

Sealant

(at top and

sides only)

Sellador

(únicamente en

los laterales y en

la parte superior)

Interior

9014018

Seal top and sides. Seal at sill and oor.

Selle la parte superior y los laterales. Selle el riel y el piso.

If using remodel bracket, continue to follow this instruction guide

excluding sill clip references.

Si va a utilizar el soporte de remodelación, siga la guía de

instrucciones pero ignore las referencias de los sujetadores de riel.

Exterior

Flashing

Fold house wrap down and tape.

Doble el house wrap hacia abajo y coloque cinta.

Apply ashing over drip cap leg, overlapping side ashing.

Aplique el ashing sobre la pata de la tapa de goteo, superponiéndolo

sobre el ashing de la peana.

Tape

Cinta

Overlap Side

Flashing

Superponga

el ashing de

la peana

Low Expanding Foam

(at top and sides)

Espuma de baja expansión

(en los laterales y en la

parte superior)

Sealant (at sill)

Sellador (en el riel)

IMPORTANT/IMPORTANTE

Exterior

9014018

Insert backer rod at sides and top between frame and nish material.

Introduzca la varilla de respaldo en los laterales y en la parte superior

entre el marco y el material de acabado.

Leave 1/4" gap at head and sides between exterior trim/siding/

stucco/brick and window for sealing.

Deje un espacio de 1/4" en la cabecera y en los laterales entre el

contramarco/el revestimiento/el estuco/el ladrillo exterior y la

ventana para el sellado.

Interior

Position sill clips and fasten. Skip this step for remodel bracket applications.

Ubique y ajuste los sujetadores del riel. Saltee este paso para aplicaciones de soporte de remodelación.

Center

Centro

12"

12" Masonry Floor/Piso de mamposteríaWood Floor/Piso de madera

Rigid sill pan modication may be required for sill clip anchoring and

sealing. Failure to seal sill pan will result in water damage to property.

Puede ser necesaria la modicación de la placa del riel rígida para el

anclaje y sellado del sujetador del riel. No sellar la placa del riel puede

provocar que el agua dañe la propiedad.

For masonry installations use masonry screws.

Para instalaciones de mampostería, utilice

tornillos para mampostería.

10 x 1" Stainless Steel Screw

Tornillo de acero inoxidable

No. 10 x 1"

1" Masonry Screw

(outside holes only)

Tornillo para mampostería de 1"

(oricios externos únicamente)

Sill Clip

Sujetador

de riel

Sill Clip

Sujetador

de riel

Backer Rod

Varilla de

respaldo

Putty Knife

Espátula

Trim

Contramarco

IMPORTANT/IMPORTANTE

NOTICE / AVISO

Exterior

Interior

9014018

Stationary Panel

Panel estacionario

Seal on sides and top. Do not seal at sill or block drainage doors.

Selle en los laterales y la parte superior. No selle el riel ni selle/

bloquee las puertas de drenaje.

Position stationary panel side jamb trim piece to stationary side jamb,

tight at top.

Coloque el contramarco de jambas laterales del panel estacionario en

la jamba lateral estacionaria y ajuste en la parte superior.

Open operating panel slightly. Remove adjustment hole caps. Insert at blade screwdriver into sockets and turn clockwise to raise panel or

counterclockwise to lower panel until gap is equal full length. Replace adjustment hole caps.

Abra ligeramente el panel operativo. Retire los tapones de oricios de ajuste. Coloque un destornillador de punta plana dentro del adaptador y gire

hacia la derecha para levantar el panel o hacia la izquierda para bajar el panel hasta que el espacio sea igual en todo el largo. Retire las tapas para

oricios de ajuste.

Adjustment hole caps are small parts. And if

swallowed, could pose a choking hazard to

young children. Replace caps after making

adjustments.

Las tapas para oricios de ajuste son piezas

pequeñas. En caso de ingesta, pueden

representar un riesgo de asxia para niños

pequeños. Vuelva a colocar los tapones

después de realizar los ajustes.

WARNING / ADVERTENCIA

Equal gap between

panel and side jamb

Igual espacio entre

el panel y la jamba

lateral

Stationary Jamb Trim

(attach to frame side jamb)

Do not seal along sill or

seal/block drainage doors.

No selle a lo largo del riel ni

selle/bloquee las puertas

de drenaje.

Adjustment

Hole Cap

Replace when

adjustment is

complete.

Tapón para

oricio de ajuste

Vuelva a colocarlo

cuando el ajuste

esté completo.

Backer Rod

Varilla de

respaldo

Sealant

Sellador

Trim

Contramarco

Raise

Para

levantar

Lower

Para

bajar

Flat Blade

Screwdriver

Destornillador

de punta plana

Contramarco de jamba

estacionaria

(conéctelo a la jamba

lateral del marco)

or/

o bien

Interior

Insert lock in operating panel with lock button on top.

Introduzca el cerrojo en el panel operativo con el botón del cerrojo en

la parte superior.

Operating Panel

Panel operativo

Lock Button on top

Botón del cerrojo

Lock

Cerrojo

Insert lock in operating panel with lock button on top and

fasten using two (2) #10 x 3" stainless steel screws.

Introduzca el cerrojo en el panel operativo con el botón del

cerrojo en la parte superior y fíjelo con dos (2) tornillo de

acero inoxidable No. 10 x 3"

Lock Button on top

Botón del cerrojo

#8-32 x 7/8"

Machine Screw

Tornillo para metales

No. 8-32 x 7/8"

Reverse Angle

Ángulo trasero

Interior View

Vista interior

>TARGET< Area

(on top)

Área destinada

(en la parte

superior)

#10-32 x 1-1/4"

Machine Screws

Tornillos para metales

No. 10-32 x 1-1/4"

9014018

Insert receiver and secure as shown. Do not fully tighten screws.

Inserte el receptor y fíjelo como se muestra. No ajuste

completamente los tornillos.

Assemble ush mount receiver and bezel. Insert receiver/bezel

assembly and secure as shown. Do not fully tighten screws.

Ensamble el receptor de montaje embutido y el bisel. Inserte el

ensamble del receptor y bisel y fíjelo como se muestra. No ajuste

completamente los tornillos.

For Flush Mount Hardware/

Para herrajes de montaje embutido

For Reachout Lock Hardware/

Para herrajes de cerrojo de alcance

Jamb

Jamba

Reachout Lock

Receiver

Receptor de

bloqueo de alcance

Jamb

Jamba

Bezel

Bisel

Receiver

Receptor

Open edge

toward exterior

Borde abierto

hacia el

exterior

Reverse Angle

Ángulo trasero

Flush Mount Receiver

Receptor de montaje embutido

or/

o bien

#10 x 3"

Stainless

Steel Screws

Tornillo de

acero

inoxidable

No. 10 x 3"

Lock

Cerrojo

For Flush Mount Hardware/

Para herrajes de montaje embutido

For Reachout Lock Hardware/

Para herrajes de cerrojo de alcance

Retract lock hooks by turning lock adjustment screw counterclockwise 2 turns, then apply receiver position template into ush mount lock.

Retraiga los ganchos del cerrojo girando 2 vueltas en sentido contrario a las agujas del reloj el tornillo de ajuste del cerrojo y, a continuación,

aplique el plantilla de posición del receptor en el cerrojo de montaje embutido.

9014018

Interior

1 2

Receiver

Position

Template

Plantilla de

posición del

receptor

For Flush Mount Hardware ONLY

SOLO para herrajes de montaje embutido

Turn lock adjustment screw

counterclockwise 2 turns.

Gire 2 vueltas en sentido

contrario a las agujas del reloj el

tornillo de ajuste del bloqueo.

Insert receiver position

template into lock.

Inserte el plantilla de

posición del receptor en

el cerrojo.

Flush Mount Lock

(with lock hooks

retracted)

Cerrojo de montaje

embutido (con los

ganchos de cierre

retraídos)

Close operating panel and align lock to receiver as shown. Slide latch receiver up or down as needed. Tighten receiver screws when properly aligned

using a phillips screwdriver for machine screws, and drill/driver for wood screws.

Cierre el panel de control y alinee el cierre con el receptor como se muestra. Deslice el receptor de pestillo hacia arriba o hacia abajo según sea

necesario. Apriete los tornillos del receptor cuando estén correctamente alineados utilizando un destornillador Phillips para tornillos de máquina y

un taladro/atornillador para tornillos de madera.

9014018

Interior

Failure to properly align lock button and latch receiver

will prevent lock from operating and may result in loss

of building security.

Si no se alinean correctamente el botón del cerrojo y

el receptor de aldaba, el cerrojo no funcionará y esto

puede provocar la pérdida de la seguridad del edicio.

WARNING / ADVERTENCIA

Receiver

Receptor

DO NOT over tighten screws. Doing so

could result in product damage.

NO ajuste demasiado los tornillos.

De hacerlo así, el producto se podría

dañar.

NOTICE / AVISO

Operating Panel

Panel operativo

Jamb

Jamba

Receiver

Receptor

For Flush Mount Hardware/

Para herrajes de montaje embutido

For Reachout Lock Hardware/

Para herrajes de cerrojo de alcance

>TARGET< Area

Área destinada Lock Button

Botón del

cerrojo

Receiver Position Template

(attached to ush mount lock)

Plantilla de posición del

receptor

(jado al cerrojo embutido)

Flush Mount Receiver

Receptor de montaje

embutido

Jamb

Jamba

Operating Panel

Panel operativo

Flush Mount

Lock

Cerrojo

IMPORTANT / IMPORTANTE

Remove receiver position template and

dispose of properly once alignment is

complete.

Retire la plantilla de posición del

receptor y deséchela adecuadamente

luego de completar la alineación.

Panel rotated

for clarity

Panel girado

para mayor

claridad

Panel rotated

for clarity

Panel girado

para mayor

claridad

Place shim(s) behind latch receiver between door jamb and framing. Install security screw(s) in receiver as shown.

Coloque una cuña detrás del receptor de pestillo entre la jamba de la puerta y el marco. Instale tornillos de seguridad en las cestas del receptor.

9014018

Interior

Failure to shim directly behind latch receiver when installing security screw may result in

bowing of the receiver jamb.

El hecho de no colocar una cuña directamente detrás del receptor de pestillo al instalar

el tornillo de seguridad puede hacer que la jamba se curve.

Fasten through

receiver basket

using required

security screw size.

Sujete a través de la

cesta del receptor

utilizando el tamaño

de tornillo de

seguridad requerido.

Shim behind receiver

as shown.

Coloque la cuña detrás

del receptor como se

muestra.

Drill a hole approximately

4" deep from the face of the

receiver through center hole

into rough opening. (DO NOT

drill if fastening to adjoining

door/sidelight).

Taladre un oricio de

aproximadamente 4" de

profundidad desde la cara del

receptor a través del oricio

central hasta la abertura en la

pared. (NO taladrar si se ja a

la puerta/luz lateral contigua).

Fasten through center

hole using required

security screw size.

Fije a través del oricio

central con el tamaño

de tornillo de seguridad

requerido.

1/8" Drill Bit

Broca para

taladro

de 1/8"

Shim

Cuña

Flush Mount

Lock Receiver

Receptor

de Cerrojo

de montaje

embutido

For Flush Mount Hardware/

Para herrajes de montaje embutido

For Reachout Lock Hardware/

Para herrajes de cerrojo de alcance

NOTICE / AVISO

or/

o bien

#10 x 3" Security Screw (For fastening to rough opening)

Tornillo de seguridad n.º 10 x 3" (Para fijar a la abertura en

la pared)

—or/ o bien—

#10 x 1 1/2" Security Screw (For fastening to adjoining

door/sidelight, supplied by others)

Tornillo de seguridad n.º 10 x 1 1/2" (Para fijar a la puerta/

luz lateral contigua, proporcionada por terceros)

IMPORTANT / IMPORTANTE

Shim (behind

receiver basket)

Cuña (detrás de la

cesta del receptor)

#10 x 4" Security Screw (For fastening to rough opening)

Tornillo de seguridad n.º 10 x 4" (Para fijar a la abertura en la pared)

—or/ o bien—

#10 x 2 1/2" Security Screw (For fastening to adjoining door/

sidelight, supplied by others)

Tornillo de seguridad n.º 10 x 2 1/2" (Para fijar a la puerta/luz lateral

contigua, proporcionada por terceros)

Shim behind

receiver as shown.

Coloque la cuña

detrás del receptor

como se muestra.

Reachout Lock

Receiver

Receptor de

bloqueo de

alcance

Installing shorter security screw(s) is required when doors or sidelights are joined to the

operating side jamb.

Se deben instalar tornillos de seguridad más cortos cuando las puertas o los paneles jos

laterales están unidos a la jamba lateral operativa.

Interior

9014018

Apply nish trim after drywall is installed.

Coloque el contramarco de acabado después de instalar la mampostería. ▶Installation is complete.

Se ha completado la instalación.

▶Proceed to hardware application guide.

Continúe con la guía para la aplicación de herrajes.

Do not apply nish trim more than 1/8" over side

panel stop. Panel or side panel damage may occur.

No aplique el contramarco de acabado a más de

1/8" por encima del tope del panel lateral. El panel

o el panel lateral pueden dañarse.

Do not apply nish trim more than 1/8" over head

panel stop. Panel removal will be compromised.

No coloque el contramarco de acabado a más de

1/8" por encima del tope del panel de cabecera. La

extracción del panel puede dicultarse.

Interior

Apply hardware following hardware installation guide for 2-Panel Door.

Aplique el herraje. Para ello, siga la guía de instalación de herrajes para

puertas de 2 paneles.

<1/8"

Finish Trim

Contramarco de acabado

<1/8"

Finish Trim

Contramarco

de acabado

Panel

Side Panel Stop

Tope del panel lateral

Side Panel Stop

Tope del panel lateral

NOTICE / AVISO NOTICE / AVISO

1 2

Interior Interior

3 4

Interior Interior

Open operating panel and remove head stop screws and save for

reinstallation.

Abra el panel operativo y retire los tornillos del tope de cabecera y

guárdelos para volver a instalarlos.

Close and lock operating panel. Remove remaining head stop and

bumper screws and save for reinstallation.

Cierre y bloquee el panel operativo. Retire los tornillos del tope de

cabecera y del tope del panel restantes y guárdelos para volver a

instalarlos.

Operating Panel

Panel operativo

Lower head stop to top of operating panel and rotate

out from operating panel side jamb to remove.

Baje el tope de cabecera hacia la parte superior

del panel operativo y gírelo hacia fuera de la jamba

lateral del panel operativo para extraerlo.

Open operating panel. Tip top of operating panel out

and lift to remove.

Abra el panel operativo. Incline la parte superior del

panel operativo hacia afuera y levántelo para retirarlo.

Panel Removal / Extracción del panel

▶Operating panel removal

complete.

Se ha completado la extracción

del panel operativo.

Head Stop

Tope de cabecera

Head Stop

Tope de

cabecera

Drill/Driver

Taladro/

destornillador

23 9014018

Andersen A-Series 2-Panel Assembled Gliding Patio Doors Guía de instalación

Marca: Andersen

Modelo: A-Series 2-Panel Assembled Gliding Patio Doors

Tipo: Guía de instalación

Descargar PDF

informe

en otros idiomas

English: Andersen A-Series 2-Panel Assembled Gliding Patio Doors Installation guide

Andersen A-Series 2-Panel Assembled Gliding Patio Doors Guía de instalación

Andersen A-Series 2-Panel Assembled Gliding Patio Doors Guía de instalación

en otros idiomas

Artículos relacionados