Nilfisk-ALTO Neptune 8 Operating Instructions Manual

Marca: Nilfisk-ALTO

Modelo: Neptune 8

Categoría: Limpiadores de alta presión

Tipo: Operating Instructions Manual

Este manual también es adecuado para

NEPTUNE 5

NEPTUNE 7

NEPTUNE 8

301002099 - 2005-01-10

english

Operating Instructions ................................1-18

deutsch Betriebsanleitung ...................................... 19-36

français Notice d’utilisation ....................................37-54

nederlands Gebruiksaanwijzing ..................................55-72

italiano Istruzioni sull’uso ......................................73-90

norsk Driftsinstruks ........................................... 91-108

svensk Bruksanvisning .....................................109-126

dansk Driftsvejledning .....................................127-144

suomi Käyttöohje ..............................................145-162

slovensći Navodilo za uporabo ...............................163-180

hrvatski Uputstvo za rad .......................................181-198

slovenský Prevádzkový návod..................................199-216

český Provozní návod ........................................ 217-234

polski Instrukcja obsługi ....................................235-252

magyar Kezelési utasítás .....................................253-270

ðóññêèé Ðóêîâîäñòâî ïî ýêñïëóàòàöèè ...............271-288

español Instrucciones de manejo ......................289-306

português Instruções de operação ........................307-324

ελληνικά Οδηγίες λειτουργίας ..............................325-342

türkçe Ýþletme kýlavuzu ..................................... 343-360

psi

bar

NEPTUNE 5 / 7 / 8

english

Options / model variants

NEPTUNE 5 / 7 / 8

Contents

Symbols used to mark

instructions

1 Important safety

instructions

2 Description

3 Before starting the cleaner

4 Control / Operation

5 Applications and methods

6 After using the cleaner

7 Maintenance

8 Troubleshooting

9 Further information

............................................................................................2

2.1 Purpose ................................................................................4

2.2 Operating elements ..............................................................5

3.1 Transport and assembly .......................................................5

3.2 Set the brake ........................................................................5

3.3 Install Crank handle for high pressure hose reel/cord reel ...6

3.4 Fill up detergent tanks ..........................................................6

3.5 Fill up tank for Nilfisk-Alto AntiStone (Anti-Scale) ................6

3.6 Adjusting the Nilfisk-Alto AntiStone (Anti-Scale) device .......6

3.7 Fill up fuel tank .....................................................................7

3.8 Connecting the high pressure hose ......................................7

3.9 Connecting the water supply ................................................7

3.10 Electrical connection ............................................................8

3.11 Antifreeze - before first use ..................................................8

4.1 Connections .........................................................................8

4.2 Switching on the cleaner ......................................................9

4.3 Pressure regulation (Tornado Lance) ...................................9

4.4 Pressure regulation (VarioPress Gun)

.............................. 10

4.5 Using cleaning agents ........................................................10

5.1 Techniques .........................................................................10

5.2 Some typical cleaning tasks ...............................................11

6.1 Switching off the cleaner ....................................................13

6.2 Disconnecting supply lines .................................................13

6.3 Rolling up the electrical lead and storing accessories .......13

6.4 Storing the cleaner (below 0°C (32°F / Freezing) ...............13

7.1 Maintenance Schedule .......................................................14

7.2 Maintenance work ..............................................................14

8.1 Indications on Display ........................................................16

8.2 Indication lights on control panel ........................................17

8.3 Other Faults ........................................................................17

9.1 Recycling the cleaner .........................................................17

9.2 Warranty .............................................................................18

9.3 Technical data ....................................................................18

9.4 EU Declaration of Conformity .............................................18

english

Options / model variants

NEPTUNE 5 / 7 / 8

1 Important safety instructions

Symbols used to mark

instructions

Before using the

high-pressure

cleaner, be sure

to also read the

enclosed operat-

ing instructions

and keep them within reach at

all times.

For your own safety

The high-pressure cleaner should

only be used by authorized per-

sons who have been instructed

in its use.

Although extremely easy to

operate, children should not be

allowed to use the cleaner.

General

Use of the high-pressure cleaner

is subject to the applicable local

regulations.

Besides the operating instruc-

tions and the binding accident

prevention regulations valid in the

country of use, observe recog-

nized regulations for safety and

proper use.

Do not use any unsafe work

techniques.

Transport

Transport of the high-pressure

cleaner is easy on its large

wheels.

For safe transport in and on ve-

hicles we recommend preventing

the equipment from sliding and

tilting. Secure it with tie-downs

and apply the parking brake on

the castor wheel.

For transport at temperatures

around or below freezing 0°C

(32°F), anti-freeze should be

drawn into the pump beforehand

(see chapter 6).

Before starting the cleaner

If your 3-phase cleaner was sup-

plied without a plug, have it ﬁ tted

with a suitable 3-phase plug with

ground, by a qualiﬁ ed electrician.

Before use, check that the high-

pressure cleaner is safe and in

proper condition.

Regularly check whether the

power cord is damaged or shows

signs of ageing.

Use the high-pressure cleaner

only when the power cord is in

a safe condition. (risk of electric

shock using damaged cord!).

Check the rated voltage of the

high-pressure cleaner before

connecting it to the mains power

supply. Ensure that the voltage

shown on the rating plate cor-

responds to the voltage of the

power supply.

We strongly recommend that the

power supply to the high pres-

sure cleaner be connected via a

residual current circuit breaker.

This device stops the supply of

electricity if the leakage current

to the ground exceeds 30 mA for

30 ms or it has an ground tester

circuit.

Please observe the regulations

and provisions applicable in your

area. Before putting the high-

pressure cleaner into service,

carry out a visual check of all the

major components.

Safety instructions

in these operating

instructions which

must be observed

to prevent risks

to persons are marked with this

danger symbol.

This symbol is used to

mark safety instruc-

tions that must be

observed to prevent

damage to the machine

and its performance.

This indi-

cates tips

and instructions

to simplify work

a n d to ensure safe opera-

tion.

Operations

marked with this

symbol should

only be carried

out by Nilfisk-

Alto Service

Technicians.

english

Options / model variants

NEPTUNE 5 / 7 / 8

CAUTION!

High-pressure water jets can

be dangerous if misused. The

jet must not be directed at per-

sons, animals, live electrical

equipment or the cleaner itself.

Wear appropriate protective

clothing and eye protection.

Do not direct the jet towards

yourself or towards other per-

sons in order to clean clothes or

footwear.

During operation of the cleaner,

recoil forces are produced at the

gunvalve and spray lance and,

when the spray lance is held at

an angle, a torque is also cre-

ated. The gunvalve and spray

lancemust therefore be held

ﬁ rmly in both hands.

Do not use the cleaner when

other people without protective

clothing are in the working area.

Check that cleaning will not result

in dangerous substances (e.g.

asbestos, oil) being washed off

the object to be cleaned and

harming the environment.

Do not clean delicate parts

made of rubber, fabric, etc. with

the 0° jet. Keep some distance

between high pressure nozzle

and surface in order to prevent

the surface from damage.

Do not use the high-pressure

hose for lifting loads.

NOTE!

The maximum permissible work-

ing pressure and temperature

are printed on the high-pressure

hose.

Do not use the cleaner if the

power cord or high-pressure

hose is damaged.

Ensure adequate air circulation.

Do not cover the cleaner or oper-

ate it in inadequately ventilated

rooms!

Store the cleaner where

it will not be exposed

to frost!

Never operate the cleaner with-

out water. Even brief shortages of

water result in severe damage to

the pump seals.

Operation

Keep cabinet and service door

closed during operation.

CAUTION!

Unsuitable extension cords

can represent a source of

danger. Always unwind cord

from the reels completely to

prevent the power cord over-

heating.

Connectors and couplings of

extension cords must be water-

tight.

Extension cords are not recom-

mended, however if necessaray

refer to the following recommen-

dations:

Cord length

Cross section

up to16 A up to 25 A

up to 20 m

(US: 30 ft)

(US: 50 ft)

(US: 75 ft)

ø1.5mm²

14 gauge

12 gauge

10 gauge

ø2.5mm²

12 gauge

10 gauge

not recom-

mended

20 to 50 m

ø2.5mm² ø4.0mm²

Do not damage the power cord

(e.g. by driving over it, pulling or

crushing it).

Disconnect the power cord by

grasping the plug only (do not

pull or tug the power cord).

CAUTION!

Unsuitable fuels (e.g. gasoline)

must not be used as they can

explode and catch ﬁ re.

Use clean fuel only, free of mois-

ture and contamination. Contact

your dealer for fuel source and

type recommendations.

This machine can be used with

Bio-Diesel (DIN 51606). How-

ever, our experience has shown

that the fuel quality is often

outside the recognized stand-

ards. An organic product like

Bio-Diesel can be affected by

long-term storage (e.g. over the

winter), extreme temperatures,

or improper transportation. When

the condition of the fuel is outside

the standards, trouble may occur

which cannot be covered by the

Warranty.

If the machine is to be oper-

ated at fuel stations or in other

potentially hazardous areas, the

machine may only be employed

outside the hazard areas deﬁ ned

in the German „Technical Guide-

lines for Inﬂ ammable Fluids“ ap-

plicable at the point of use due

to the potential explosion hazard

posed by the burner.

If the machine is to be operated

indoors, the local building regu-

lations must be observed for the

discharge of the exhaust fumes

into the atmosphere. Ensure an

adequate supply of fresh air.

If the machine is to be connected

to a ﬂ ue gas stack, then local

building regulations must be ob-

served. We will be glad to provide

tips for connection systems, on

request.

CAUTION!

Do not touch or cover the ex-

haust. Risk of burns and ﬁ re.

Electrical equipment

CAUTION!

Never spray electrical equip-

ment with water: risk of elect-

trical shock and short-circuit.

The cleaner may only be con-

nected to a correctly installed

plug socket.

Switching on the cleaner may

cause voltage ﬂ uctuations.

Voltage ﬂ uctuations should not

occur if the impedance at the

transfer point is less than 0.15

If in doubt ask your local electric-

ity supplier.

english

Options / model variants

NEPTUNE 5 / 7 / 8

Maintenance and repair

CAUTION!

Always remove the plug from

the power supply before clea-

ning or carrying out mainte-

nance work on the cleaner.

Carry out only the maintenance

operations described in the

operating instructions. Use only

original Nilﬁ sk-Alto spare parts.

Do not make any technical modi-

fications to the high-pressure

cleaner.

Ensure that the machine is regu-

larly serviced by authorized

Nilﬁ sk-Alto dealers in accordance

with the maintenace plan. Failure

to do so will void the warranty.

CAUTION!

High-pressure hoses, ﬁ ttings

and couplings are important

for the safety of the cleaner.

Use only high-pressure parts

approved by the manufacturer!

The power cord must not differ

from the version speciﬁ ed by the

manufacturer and may only be

changed by an electrician.

Please contact your local author-

ized Nilﬁ sk-Alto equipment dis-

tributor for all other maintenance

or repair needs!

Testing

The cleaner conforms to the Ger-

man „Guidelines for Liquid Spray

Jet Devices“. The high-pressure

cleaner must be subjected to a

safety examination in accord-

ance with the „Accident Preven-

tion Regulations for Working

with Liquid Spray Jet Devices“

as required, but at least every

12 months, by an authorised

inspector.

After all repairs or modifica-

tions to electrical equipment,

the protective conductor resist-

ance, the insulation resistance

and the leakage current must

be measured. Furthermore, a

visual inspection of the mains

power lead, a voltage and current

measurement and a function test

must be carried out. Our after-

sales service technicians are

at your disposal as authorised

inspectors.

The complete „Accident Preven-

tion Regulations for Working

with Liquid Spray Jet Devices“

are available from the Carl Hey-

manns Verlag KG, Luxemburger

Strasse 449, 50939 Cologne or

from the appropriate association

of employers’ liability insurances.

The pressure-bearing parts of

this high-pressure cleaner have

been manufactured in accord-

ance with § 9 of the German

Pressure Vessels Ordinance

and successfully subjected to a

pressure test.

Unloader valve

Pump pressure is reduced by

means of an "unloader valve"

which returns water to the inlet

side of the pump at a minimum

pressure. The point at which this

occurs is set and sealed at the

factory and must not be adjusted.

2 Description

2.1 Purpose This high-pressure cleaner has

been designed for professional

use in

– Agriculture

– Industry

– Transport industry

– Automotive

– Municipal Facilities

– Janitorial

– Construction

– Food Industry

etc.

Chapter 5 describes the use of

the high-pressure cleaner for

various cleaning jobs.

Always use the cleaner as de-

scribed in these operating in-

structions. Any other use may

damage the cleaner or the sur-

face to be cleaned or may result

in severe injury to persons.

english

Options / model variants

NEPTUNE 5 / 7 / 8

2.2 Operating elements

See fold-out page at front of these

operating instructions.

1 Spray lance

2 Spray lance storage

3 Control panel

4 Crank handle for

High pressure hose reel

(Neptune ..X)

Cord reel (Neptune ..X2)

5 Fuel level gauge

6 Tank ﬁ ller for fuel

7 Receptacle for service

crane and lifting ring

8 Top cover release

9 Service door release

10 Crank handle for

High pressure hose reel

(Neptune ..X2)

11 High pressure hose connec-

tion for machines without

hose reel

12 Main switch ON/OFF - cold

water/hot water

13 Display (Temperature or

Codes)

14 Temperature control

15 Low fuel indicator

16 Low Nilﬁ sk-Alto AntiStone

(Anti-Scale) indicator

17 Service interval due/expired

18 Pump oil low

19 Detergent metering knob

20 Pressure gauge

21 Power ON

22 Castor with parking brake

23 Water supply connection

24 Tank ﬁ ller for anti-freeze

25 Tank ﬁ ller for Nilﬁ sk-Alto

Anti-Scale

26 Canister for detergent B

27 High pressure hose reel

(Neptune ..X)

28 Power cord reel

(Neptune ..X2)

29 Tank ﬁ ller for detergent A

30 Grip for top cover

3 Before starting the cleaner



3.1 Transport and assembly

chine by hand from the pallet.

Due to the weight this work

should be done by at least

three persons.

CAUTION!

Do not hold the plastic tank to lift

the machine as it could become

detached from the frame.

The best places to hold the ma-

chine are

– on the handle

– on the frame between the front

wheels and the guide rollers.

Every fuel-burning appliance, such

as pressure washers, depends

upon a proper mix of fuel and air

(by weight) for proper combustion.

Therefore some adjustment of the

air supply to the burner may be nec-

essary to take account of altitude

and the resulting air pressure. This

is true whether your fuel is ‘Natural

gas’, Propane or Diesel.

Your Nilﬁ sk-Alto hot water pressure

washer was thoroughly tested and

adjusted for optimum performance

before it left our factory. The factory

is located at approximately 200m

(650 ft) above sea level, and the

combustion settings are optimal for

that elevation.

If your location is higher than

1200m (3900 ft) above sea level,

your burner may require re-ad-

justment for proper performance

and best fuel economy. Contact

your Dealer or Nilﬁ sk-Alto for

assistance.

3.2 Set the brake

1. Before using the cleaner for

the ﬁ rst time, check it carefully

for any faults or damage.

2. Run the machine only when it

is in perfect working condition.

3. Set the brake.

1. The safest way to lift the ma-

chine is to use a fork-lift truck

The arrows in the illustration

indicate the best places to po-

sition the fork.

2. It is also possible to lift the ma-

english

Options / model variants

NEPTUNE 5 / 7 / 8

3.5 Fill up tank for Nilfisk-

Alto AntiStone (Anti-

Scale) indicator

1. Fill up Nilfisk-Alto Anti-Stone

(Anti-Scale)/water softener res-

ervoir with the sample bottle

provided. Nilﬁ sk-Alto AntiStone

(Anti-Scale) prevents any depos-

its of scale and acts at the same

time as a corrosion inhibitor.

For compatibility reasons, use only

the tested Nilfisk-Alto AntiStone

(Anti-Scale) which is available as a

six-pack of 1 liter bottles by ordering

part number 8466.

3.4 Fill up detergent tanks

1. Fill up detergent tanks (A)

and (B) with prediluted detergent.

Capacity see chapter 9.3 Techni-

cal Data

3.3 Install Crank handle

for high pressure hose

reel/cord reel

1. Pull cap of crank in arrow

direction.

2. Align tabs on crank with slot

in axle.

3. Put crank on axle of high

pressure hose reel/cord reel.

4. Fix crank by pushing the cap.

3.6 Adjusting the Nilfisk-

Alto AntiStone (Anti-

Scale) device

The Nilﬁ sk-Alto AntiStone device is

set at the factory to a water hardness

of class 2. Adjustment:

1. Open cabinet (A) and service

door (B).

2. Only on ..X2 models: remove

crank.

3. Measure the water hardness or

ask your water supply company.

4. Set the adjusting knob to re-

quired position.

mg/l Grains

dH °e °f ppm Ca Description Setting

NEPTUNE 5 NEPTUNE 7/8

0-17 0-1

0-7 0-8,8 0-12,5 0-50

Soft 0 0

17-60 1,1-3,5 Slightly Hard 1 1-2

60-128 3,6-7,5 7-14 8,8-17,5 12,5-25,1 51-150

Moderately Hard

2 2-3

128-180 7,6-10,5 14-21 17,5-26,3 25,1-37,6 151-300 Hard 3 3-4

>180 >10,5 >21 >26,3 >37,6 >300 Very Hard 4 4

english

Options / model variants

NEPTUNE 5 / 7 / 8

3.7 Fill up fuel tank

With the machine cold, turned

off and disconnected from power

supply:

1. Fill fuel tank from a clean con-

tainer with a fresh fuel (fuel oil

EL, or Diesel oil DIN 51 603),

or fuel type recommended by

your distributor.



Bio-Diesel can be used, see

notes in chapter 1.

The fuel must be free from con-

tamination.

Tank capacity see chapter 9.3

Technical data.

months it is recommended that

a fuel conditioner/stabilizer be

added (available from the fuel

oil trade).

3.8 Connecting the high

pressure hose

3.8.1 Machines with high

pressure hose reel

1. Connect the high pressure

hose quick connector to the

high pressure nipple (A) lo-

cated at the hose reel axle.

2. Place the high pressure hose

into the hose guide (B) and

ritain it with the clip.

3. Release the brake (C) on the

hose reel and wind up the

high pressure hose.

3.8.2 Machines without high

pressure hose reel

1. Connect the high pressure

hose quick connector to the

high pressure nipple located

at right rear of machine above

chemical tank.

3.9 Connecting the water

supply

1. Attach quick connect adapter

found with Owners Manual to

the water supply hose.

2. Rinse the water supply hose

brieﬂ y in order to prevent sand

an other dirt particles entering

into the machine.

3. Attach water supply hose with

adapter to inlet quick connec-

tor.

4. Open water supply faucet.

NOTE!

At temperatures below 8°C

(46°F), the fuel oil begins to so-

lidify (parafﬁ n precipitation). This

can lead to difﬁ culties in starting

the burner. Before the winter

english

Options / model variants

NEPTUNE 5 / 7 / 8



4 Control / Operation

4.1 Connections

4.1.1 Connecting the spray

lance to the spray gun

1. Pull the blue quick-release

grip (A) of the spray gun for-

wards and lock it by turning it

to the left.

2. Insert the nipple of the spray

lance (C) into the quick-re-

lease connection and turn

the blue quick-release grip to

the right (B).

3. Pull the spray lance (or other

accessory) forwards to check

that it is securely attached to

the spray gun.

NOTE!

Always remove any dirt from

the nipple before connecting the

spray lance to the spray gun.

3.10 Electrical connection

3.11 Antifreeze -

before first use

The machine is ﬂ ushed with anti-

freeze at the factory to protect it

against freezin; this mixture (ap-

prox. 5 l) may be captured in a

suitable container for reuse.

CAUTION!

230 V / 400 V ?

(220 V / 440 V ?)

Some models have tha ability to

be used on either 230 Volt or a

440 Volt power supply. On these

models conﬁ rm that the voltage

selector switch is in the proper

position to match the power

supply. Otherwise damage to

machines electrical components

may occur.

CAUTION!

When using a cord reel:

1. Release brake of the cord

reel.

2. Unwind the cord completely.

CAUTION!

The cleaner should only be con-

nected to a correctly installed

electrical supply.

1. Observe safety instructions in

chapter 1.

2. Insert the plug into the electri-

cal socket.



NOTE!

See chapter 9.3 Technical Data

for required quantity of water and

water pressure.

In the case of poor water quality

(sand, etc.), it is recommended

that an inlet water ﬁ lter be in-

stalled.

Water supply hose should be

a reinforced hose and have a

minimum inside diameter of 3/4"

(19 mm).

400V

230V

400V

english

Options / model variants

NEPTUNE 5 / 7 / 8

1. Open cabinet (and service door

if desired - see chapter 3.6, Step

1+2).

2. Turn the twist grip on the safety

control block all the way to the left

(counter- clock wise-direction).

3. Turn the main switch to position

4. Select temperature (over 100°C

(212°F)).

For special applications: replace the

standard nozzle with the steam spray

nozzle (accessory).



4.2 Switching on the

cleaner

4.2.1 Cold water operation /

Hot water operation (up

to 100°C)

1. Turn the main switch to posi-

tion

(cold water).

Control electronics accomplishes

a self check.

The Display shows for approx. 1

second „---“.

The motor starts.

is ON.

2. Turn the main switch to posi-

tion (hot water).

3. Select temperature.

4. Unlock the spray gun and

squeeze trigger.

5. The oil burner will light.

6. Release trigger and lock the

spray gun when not in use.

NOTE!

The cleaner switches off auto-

matically twenty seconds after

the spray gun has been closed. To

start the cleaner again, squeeze

the trigger and the machine will

start automatically.

4.3 Pressure regulation

(Tornado Lance)

1. Turn the twist grip on the spray

unit:

– High pressure =

clockwise (+) for high pres-

sure

– Low pressure =

counter-clockwise (–) for low

pressure.

4.2.2 Steam operation (over

100°C (212°F))

BAR

english

Options / model variants

NEPTUNE 5 / 7 / 8

5 Applications and methods

Efﬁ cient high pressure cleaning is achieved by following a few guide-

lines, combined with your own personal experience of speciﬁ c clean-

ing tasks. Accessories and detergents, when correctly chosen, can

increase the efﬁ ciency of your pressure washer. Here is some basic

information about cleaning.

5.1.1 Soaking

Encrusted or thick layers of dirt can be loosened or softened up by a

period of soaking. This is for example an ideal method within agricul-

ture – for example, within pig sties. The ideal soaking method can be

achieved by using foam or simple alkaline detergent. Let the product

lie on the dirty surfaces for about 30 minutes before pressure wash-

ing. The result will be a much quicker high pressure cleaning process.

5.1 Techniques

4.5 Using cleaning agents

1. Select desired detergent (A)

or (B) and amount by turning

the knob to desired percent-

age.

2. Spray the object to be

cleaned.

3. Allow the cleaning agent to

work, depending on the de-

gree of soiling. Then rinse off

with high pressure.

4.4 Pressure regulation

(VarioPress Gun)

1. Turn the twist grip on the spray

unit:

Water volume

(–) (+)

min. max.

The percentage shown in the

illustration are only approximate

data.

For special applications such as

disinfection, the exact detergent

concentration has to be deter-

mined by using a graduated

measuring container. For water

outlet volume of the machine see

chapter 9.3 technical data.



CAUTION!

Never allow cleaning agent

to dry on the surface to be

cleaned. The surface may be

damaged.

ca. ca.

1%1%

english

Options / model variants

NEPTUNE 5 / 7 / 8

5.1.2 Detergent and Foam

Foam or detergent should be applied onto dry surfaces so that the

chemical product is in direct contact with the dirt. Detergents are ap-

plied from bottom to top, for example on a automobile bodywork, in

order to avoid “super clean” areas, where the detergent may collect

in higher concentrations and streams downwards. Let the detergent

work for several minutes before rinsing before rinsing and never let

it dry on the surface being cleaned.

5.1.3 Temperature

Detergents are more effective at higher temperatures. Greases, oils

and fats can be broken down more effectively at higher temperatures

also. Proteins can be cleaned at temperatures of around 60°C (140°F).

Oils and trafﬁ c ﬁ lm around 70°C (158°F), and grease can be cleaned

at 80°-90°C (176-194°F).

5.1.4 Mechanical Effect

In order to break down tough layers of dirt, additional mechanical

effect may be required. Special lances and rotary or wash brushes

offer this supplementary effect that cuts through dirt.

5.1.5 High Water Flow or

High Pressure

High pressure is not always the best solution and may also damage

surfaces. The cleaning effect also depends upon water ﬂ ow. Pres-

sure levels of around 100 bar (1450 psi) may be sufﬁ cient for vehicle

cleaning (in association with hot water) and higher ﬂ ow levels give

the ability to rinse and ﬂ ush away large amounts of dirt easily.

5.2 Some typical cleaning tasks

5.2.1 Agriculture

Task Accessories Method

Stables

Pig Pens, Sties

Cleaning of walls,

floors and equip-

ment

Disinfectant

Chemical Foam Injec-

tors

Foam lance

Powerspeed lance

Floor Cleaner

Detergents

Universal

Alkafoam

Disinfectant

DES 3000

1. Soaking – apply foam to all surfaces (bottom to top)

and wait for approx. 30 minutes.

2. Remove the dirt from surfaces with the high pressure

lance or chosen accessory. Again, clean from bottom

to top on vertical surfaces.

3. To ﬂ ush away large quantities of dirt, change to low

pressure mode and use the higher ﬂ ow to push away

the dirt.

4. Use recommended disinfectant products and methods

to ensure hygiene. Apply DES 3000 disinfectant once

the surfaces are perfectly clean.

Machinery

Tractors

ploughs etc.

Detergent injection

Powerspeed lances

Curved lances and un-

derchassis washers

Brushes

1. Apply detergent to vehicle or equipment surfaces in

order to soften up dirt and grime. Apply from bottom

to top.

2. Proceed with cleaning using the high pressure lance.

Clean again from bottom to top. Use accessories to

clean in difﬁ cult to reach places.

3. Clean fragile areas such as motors, rubber at lower

pressure levels to avoid damage.

english

Options / model variants

NEPTUNE 5 / 7 / 8

5.2.3 Buildings and Equipment

These are merely several examples of cleaning tasks that can be solved by a pressure washer in asso-

ciation with accessories and detergents. Each cleaning task is different. Please consult your local dealer

or Nilﬁ sk-Alto representative in order to discuss the best solution for your own cleaning tasks.

5.2.2 Vehicle

Task Accessories Method

Vehicle bodywork Standard lance

Detergent injection

Curved lances and un-

derchassis washers

brushes

Detergents

Aktive Shampoo

Aktive Foam

Sapphire

Super Plus

Aktive Wax

Allosil

RimTop

1. Apply detergent to vehicle or equipment surfaces in

order to soften up dirt and grime. Apply from bottom

to top. In cases of particularly dirty vehicles, pre-spray

with a product such as Allosil in order to remove traces

of insects etc, then rinse at low pressure and apply

normal car cleaning detergent. Let detergents settle

for 5 minutes before cleaning off. Metallic surfaces can

be cleaned using RimTop.

2. Proceed with cleaning using the high pressure lance.

Clean again from bottom to top. Use accessories to

clean in difﬁ cult to reach places. Use brushes in order

to add a mechanical cleaning effect. Short lances can

help for cleaning of motors and wheel arches. Curved

lances or undercarriage washers can be valuable for

the cleaning of car underchassis and wheel arches.

3. Clean fragile areas such as motors, rubber at lower

pressure levels to avoid damage.

4. Apply a liquid wax using the pressure washer in order

to protect the bodywork from pollution.

Task Accessories Method

General surfaces

Metallic equipment

Foam injectors Stand-

ard lance

Curved lances

Tank cleaning

head

Detergents

Intensive

J25 Multi

Combi Aktive

Alkafoam

Disinfectant

DES 3000

1. Apply thick foam over the surfaces to be cleaned. Apply

on dry surfaces. Apply from top to bottom on vertical

surfaces. Let the foam act for up to 30 minutes for the

optimal effect.

2. Proceed with cleaning using the high pressure lance.

Use applicable accessories. Use high pressure to

dislodge large amounts of incrusted dirt or grime.

Use lower pressure and high water volume in order

to rapidly ﬂ ush away loose dirt and rinse surfaces.

3. Apply DES 3000 disinfectant once the surfaces are

perfectly clean.

Areas covered by amounts of loose dirt, such as animal

remains in slaughterhouses, can be removed by using

high water ﬂ ow to ﬂ ush away the dirt to evacuation pits

or drains.

Tank cleaning heads can be used to clean barrels, vats,

mixing tanks etc. Cleaning heads may be hydraulically or

electrically powered and give the possibility for automatic

cleaning without a constant user.

Rusted or dam-

ages surfaces prior

to treatment

Wet Sandblasting

equipment

1. Connect the sandblasting lance to the pressure

washer and place the suction tube in the sand.

2. Always wear protective equipment during sandblast-

ing.

3. Spray the surfaces to be treated with the mix of water

and sand. Rust, paint etc will be stripped off.

english

Options / model variants

NEPTUNE 5 / 7 / 8

6 After using the cleaner

6.1 Switching off the

cleaner

1. Turn the main switch to posi-

tion „OFF“.

2. Turn off water supply at

faucet.

3. Squeeze the spray gun trig-

ger until the pressure has bled

off.

4. Slide trigger lock to the locked

position.

6.2 Disconnecting supply

lines

1. Turn the main switch to posi-

tion „OFF“.

2. Turn off water supply at

faucet.

3. Squeeze the spray gun trig-

ger until the pressure has bled

off.

6.3 Rolling up the electrical

lead and storing

accessories

Risk of tripping!

To prevent accidents, always

carefully roll up the power cord.

Machines with hose and/or cord

reel:

1. Wind up the power cord as il-

lustrated with the plug located

in the center of the cord reel.

2. Wind up the high pressure

hose as illustrated.

3. Place the spray lance into the

spray lance storage.

4. Slide trigger lock to the locked

position.

5. Remove the water supply

hose from the cleaner.

6. Remove power cord plug from

the electrical supply.

6.4 Storing the cleaner

(below 0°C (32°F))

Store the cleaner in a dry heated

location to protect against freez-

ing or protect per below instruc-

tions:

1. Remove the water supply

hose from the cleaner.

2. Remove the spray lance.

3. Switch on the cleaner with the

main switch in position

4. Squeeze trigger of the spray

gun.

5. Gradually pour antifreeze (ap-

prox. 5 litres) into the water

tank (A).

6. While the pump is pulling the

mixture from the water tank,

squeeze and release the trig-

ger two or three times.

7. The machine is protected

against freezing when anti-

freeze mixture emerges from

the spray gun.

8. Lock the safety catch on the

spray gun.

9. Switch off the cleaner.

10. To avoid any possible dam-

age, store the cleaner tempo-

rarily in a heated room before

using it again.

11. When the machine is put into

service again, the antifreeze

solution can be collected and

stored for future use.

english

Options / model variants

NEPTUNE 5 / 7 / 8

7 Maintenance

7.1 Maintenance Schedule

7.2 Maintenance work

7.2.1 Water ﬁ lters

Water ﬁ lters are ﬁ tted at the water

and pump inlets to prevent large

particles of dirt from entering into

the system.

1. Unscrew quick coupling.

2. Remove ﬁ lter with tool and

clean it.

3. Also clean ﬁ lter at pump inlet.

Weekly

NEPTUNE 5/8 only:

After the ﬁ rst 50

operating hours

Every six

months or

500 operating

hours

required

7.2.1 Water ﬁ lters



7.2.2 Oil ﬁ lter



7.2.3 Checking the pump oil quality



7.2.4 Changing the pump oil



7.2.5 Emptying the fuel oil tank



7.2.6 Flame Sensor



7.2.2 Oil ﬁ lter

1. Clean ﬁ lter:

Unscrew Filter cap (1)

2. Clean/replace oil ﬁ lter.

3. Properly dispose of ﬁ lter and

any solvents.

NEPTUNE 5 NEPTUNE 7

NEPTUNE 8

english

Options / model variants

NEPTUNE 5 / 7 / 8

7.2.4 Changing the pump oil

1. Unscrew the oil drain plug (A)

and drain oil into a suitable

container.

2. Check that the drain plug

gasket is in place and reinstall

drain plug.

3. Fill pump with proper grade

and amount of oil.

Oil grade and capacity see

chapter ‘9.3 Technical Data’.

7.2.3 Checking the pump oil

quality

1. Check color of pump oil.

If the oil has a grey or white

shade, change the oil (see

chapter 7.2.4)

2. Top off oil level with fresh oil

if necessary.

Oil type see chapter 9.3 Tech-

nical Data.

7.2.6 Flame sensor

1. Remove the sensor and clean

with a soft cloth.

2. Confirm that the sensor is

correctly seated when rein-

stalling.

7.2.5 Emptying the fuel oil

tank

1. Prepare a container which

is capable of containing the

amount of fuel remaining in

the tank.

2. Place drain channel beneath

the drain plug.

3. Remove the drain plug and

drain the fuel into the pre-

pared container carefully not

to spill fuel oil.

4. Check that the drain plug

gasket is in place and reinstall

drain plug.

5. Check tank and plug for

leaks.

NEPTUNE 7

NEPTUNE 5 / 8

english

Options / model variants

NEPTUNE 5 / 7 / 8

Indication

on Display

Cause Remedy

FLF

> Flow sensor fault

Contact Nilﬁ sk-Alto Service

Cold water operation possible

FLO

> Water supply turned off or inadequate supply

to machine

• Required volume ﬂ ow and pressure see

chapter 9.3 Technical Data

> Detergent tank empty • Fill detergent tank or set detergent me-

tering to „OFF“

> Pressure regulation on the safety control

block or VarioPress-lance

set to low water

volume

• Turn the twist grip on safety control block

or VarioPress-lance

to higher water/

pressure volume (see chapter 4.4)

> Machine scaled

Contact Nilﬁ sk-Alto Service

Fue

Fuel shortage • Fill fuel tank

Cold water operation possible

Hop

> Motor overheated • Turn main switch in position „OFF“, let

machine cool down

• Remove extension cord, if being used.

• Possible phase failure; have electrical

connections checked

HOS

> Machine overheated Contact Nilﬁ sk-Alto Service

LEA

> Leakage or inadmissible operating condition

by short-time operation

• After three times of short-time ope ration

the machine switches off. To reset: Turn

main switch to position “OFF“, then start

again. Keep trigger squeezed for longer

than 3 seconds. If a leak occurs in the

hose and gun and causes the machine

to start and stop brieﬂ y 3 times, then the

machine will switch off.

> Spray gun leaking • Repair Spray gun

> High pressure hose, coupling or line system

leaking

• Replace high-pressure hose, retighten

screw ﬁ ttings

> Detergent tank empty • Fill detergent tank or set detergent me-

tering to „OFF“

> Water inlet ﬁ lter dirty • Clean ﬁ lter (see chapter 7.2.1)

> High-pressure pump drawing in air • Repair leaks

LHE

> Flame sensor sooted • Clean flame sensor (see chapter

7.2.6).

> Ignition or fuel system failure

Contact Nilﬁ sk-Alto Service

Cold water operation possible

LHL

> Burner failure

Contact Nilﬁ sk-Alto Service

Cold water operation possible

POL

> Pump oil low

• Fill to proper level (see chapter 7.2.3)

SEC

> Temperature sensor damaged

Contact Nilﬁ sk-Alto Service

Cold water operation possible

SEO

> Temperature sensor damaged

Contact Nilﬁ sk-Alto Service

Cold water operation possible

UPC

> Microprocessor failure Contact Nilﬁ sk-Alto Service

8 Troubleshooting

8.1 Indications on Display

english

Options / model variants

NEPTUNE 5 / 7 / 8

8.2 Indication lights on control panel

8.3 Other Faults

Indication light Cause Remedy

ﬂ ashing

see FLO

•

see FLO

> Low fuel level • Fill fuel tank

Cold water operation possible

> Low Nilﬁ sk-Alto AntiStone (Anti-

Scale) level

• Fill Nilﬁ sk-Alto AntiStone (Anti-Scale)

tank

ﬂ ashing

> Service interval: Service due in 20

hours

Contact Nilﬁ sk-Alto Service

> Service interval expired

Contact Nilﬁ sk-Alto Service

> Pump oil low • Fill to proper level

Fault Cause Remedy

not ON

> Power cord not properly

connected to power supply

• Check power cord connetction

• Check fuse (see chapter 9.3 Technical

Data)

Pressure too low > High pressure nozzle worn

out

• Replace nozzle

> Pressure regulation set to low

pressure or VarioPress-lance

set to low water volume.

• Turn the twist grip on safety control block

clockwise (+) or set VarioPress-lance to

higher water volume (see chapter 4.4)

Machine is running with pulsating

pressure and makes knocking

noise

> Pump has drawn in air due to

detergent tank being empty

• Close detergent valve. Remove lance from

gun. Operate spray gun and let machine run

until air in pump is gone and the machine is

running normally/calm again.

No detergents drawn in > Detergent tank empty • Fill detergent tank

> Dirt in detergent tank • Clean detergent tank

> Suction valve at cleaning

agent inlet soiled

• Remove suction valve and clean or replace

Burner soots > fuel contamination

Contact Nilﬁ sk-Alto Service

> Burner sooted or adjustment

incorrect

9 Further information

9.1 Recycling the cleaner Make the old cleaner unusable

immediately.

1. Unplug the cleaner and cut

the power cord.

Do not discard of electrical ap-

pliances with household waste.

As specified in European Direc-

tive 2002/96/EC on old electrical and elec-

tronic appliances, used electrical goods

must be collected separately and recycled

ecologically.

Contact your local authorities or your near-

est dealer for further information.

9.2 Guarantee

Our general conditions of busi-

ness are applicable with regard

to the guarantee. Subject to

change as a result of technical

advances.

The guarantee is invalidated if the machine

is not operated in accordance with these

instructions or otherwise abused. The

guarantee is invalidated if the machine is

not serviced as described.

english

Options / model variants

NEPTUNE 5 / 7 / 8

US only:

This warranty is in effect from the first

day of purchase by the end user.

Each machine will have one (1) year

coverage, from date of purchase by

the end user, covering parts found

defective due to faulty components,

materials and/or bad workmanship.

Not included in this warranty cover-

age are parts found defective due to:

- Normal wear and tear (such as

seals, valves, pistons, bearings, etc.)

- Machine working under abnormal

conditions.

9.3 Technical data

9.4 EU Declaration of Conformity

Product: High Pressure Cleaner,

Type: NEPTUNE, Description: 400 V 3~, 50 Hz, IP X5

The design of the unit corresponds to the following pertinent regula-

tions: EC Machine Directive 98/37/EG, EC Low-voltage Directive 73/23/

EG, EC EMV Directive 89/336/EG. Applied harmonised standards: EN

12100-1, EN 12100-2, EN 60335-2-79, EN 55014-1, EN 55014-2, EN

61000-3-2.

- Machines being misused.

- Machines being repaired or

tampered with by unauthor-

ized person(s).

- The use of parts other than

Nilfisk-Alto Cleaning Systems,

Inc. original spare parts and/or

accessories.

The burner coil on all Nilfisk-Alto

Cleaning Systems, Inc. hot water/

steam cleaners is under warranty

for five (5) years against defects,

and the high pressure hose is

covered for an initial 30 days,

under the same conditions described

above.

Nilfisk-Alto Cleaning Systems, Inc.

will cover labor by an authorized Nil-

fisk-Alto CSI Dealer for a 12-month

period after the date of purchase of

the machine by the end user.

No other costs, other than laid out in

this warranty program, will be cov-

ered by the warranty.

Dated, End-User proof of purchase

must be submitted with any claim for

Warranty Service.

NEPTUNE

5-27 5-28

5-28X2

5-42 5-45 5-49

5-49X

5-54 5-57

5-57X

7-25

7-25X2

7-58

7-58X

7-63

7-63X2

7-66 8-103

Voltage 110 V /1~/ 50Hz

(GB)

Voltage 200 V / 3~/ 50Hz

(JP) (JP)

Voltage 200 V / 3~/ 60Hz

(JP) (JP)

Voltage 220 V / 1~/ 60Hz

(US) (US)

Voltage 220-440 V/ 3~/ 60Hz

(US) (KR) (KR) (US)

Voltage 230 V /1~/ 50Hz

(EU) (GB) (GB)

Voltage 230-400 V/ 3~/ 50Hz

(NO,BE,IT) (NO,BE,IT) (NO,BE,IT) (NO,BE,IT)

Voltage 400 V / 3~/ 50Hz

(EU) (EU) (EU) (EU) (EU)

Fuse (slow)

A 16 32 (110V)

13 (230V)

16 (EU)

25/16 NO,BE,IT)

25 (JP)

30 16 (EU)

25/16 NO,BE,IT)

30 16 (EU)

32 (NO,BE,IT)

25 (KR)

13 30 16 (EU)

25/16 (NO,BE,IT)

30 (JP), 25 (KR)

30 25

Power rating

kW 3,3 3,0 5,6 6.6 6,9 6.6 7,9 3,0 6.6 8,3 9.1 13

Working pressure

bar/MPa 110/11 90/9 (110V)

95/9.5 (230V)

170 / 17

(EU,NO,BE,IT)

165 / 16,5 (JP)

150/15 180 / 18 172/17 200 / 20 90/9 159/16 175 / 17,5 214/21 180/18

Permissible pressure

bar/MPa 200/20 250/25 200/20 250/25

Volume ﬂ ow (max)

l/h 720 720 (110V)

770 (230V)

860 (EU,NO,BE,IT)

910 (JP, 50Hz)

860 (JP, 60Hz)

970 1080 720 1260 2000

Volume ﬂ ow Q

IEC

l/h 630 660 (110V)

730 (230V)

800 (EU,NO,BE,IT)

830 (JP)

908 900 1020 1000 660 1135 1170 1135 1950

Permissible temperature

°C 80-140 80-150 80-140 80-150 80-140 100-140 90-150 100-140 90-150 70-140

Max. water inlet temperature

°C 40 30 40 30 40 30 40 30 40

Max. water inlet pressure

bar/MPa 10 / 1

Dimensions l x w x h

mm 1190 x 702 x 987 1190 x 702 x 1020

Weight

kg 175, 182(X2) 180 184, 189(X) 217, 222(X), 224(X2) 228

Noise level at a distance of 1

m EN 60704-1

dB(A) 71,8 73,8 75.8 74,1 72,5 76.6 80,2

Sound power level LW

dB(A) 86,9 88,8 90.2 89,1 87,6 91.7 95,3

Recoil forces

N 26 25/28 42 44 47 53 55 25 52 61 65 103

Fuel tank

l 35

Detergent tank A / B

l 15 / 10

Oil quantity

l 1,0 2,15

Oil type

SAE 15W-40 Castrol AlphaSyn-T ISO 150 SAE

15W-40

Applied national standards and technical

speciﬁ cations: DIN EN 60335-2-79.

Dipl. Ing. Wolfgang Nieuwkamp

Tests and approvals

Bellenberg, 10.01.2005

http://www.nilﬁ sk-alto.com

HEAD QUARTER

DENMARK

Nilﬁ sk-Advance Group

Sognevej 25

DK-2605 Brøndby

Tel.: (+45) 4323 8100

E-mail: mail.com@nilﬁ sk-advance.com

SALES COMPANIES

ARGENTINA

Nilﬁ sk-Advance srl.

Ediﬁ cio Central Park

Herrera 1855, Ofﬁ ce 604

Ciudad Autónoma de Buenos Aires

Tel.: (+54) 11 6091 1571

AUSTRALIA

Nilﬁ sk-ALTO

48 Egerton St.

PO Box 6046

Silverwater NSW 2128

Tel.: (+61) 2 8748 5966

E-mail: info@nilﬁ skalto.com.au

AUSTRIA

Nilﬁ sk-ALTO

Metzgerstr. 68

A-5101 Bergheim/Salzburg

Tel.: 0662 456 400-90

E-mail: info.at@nilﬁ sk-alto.com

Web: www.nilﬁ sk-alto.at

BELGIUM/LUXEMBURG

Nilﬁ sk-ALTO

Division of Nilﬁ sk-Advance n.v.-s.a.

Riverside Business Park

Boulevard Internationalelaan 55

Bâtiment C3/C4 Gebouw

Bruxelles 1070 Brussel

Tel.: (+32) 2 467 60 40

E-mail: info.be@nilﬁ sk-alto.com

Web: www.nilﬁ sk-alto.be

www.fr.nilﬁ sk-alto.be

CANADA

Clarke Canada

Part of the Nilﬁ sk-Advance Group

4080-B Sladeview Crescent, Unit 1

Mississauga, Ontario L5L 5Y5

Tel.: (+1) 905 569 0266

Web: www.clarkeus.com

CHILE

Nilﬁ sk-Advance S.A.

San Alfonso 1462, Santiago

Tel.: (+56) 2 684 50 00

E-mail: Pablo.noriega@nilﬁ sk.com

Web: http://www.nilﬁ sk.com/

CHINA

Nilﬁ sk-Advance Cleaning Equipment (Shenzhen)

Co., Ltd.

Room 2515, Building C

Huangdu Square 3008 Yitian Road

Futian District, Postcode: 518048

518038 Shenzhen

Tel.: (+86) 755 8359 7942

CZECH REPUBLIC

Nilﬁ sk-Advance s.r.o.

Do Čertous 2658/1

193 00 Praha 9

Tel.: (+420) 241 408 419

E-mail: [email protected]

Web: http://www.nilﬁ sk-alto.cz

DENMARK

Nilﬁ sk-ALTO

- en division af Nilﬁ sk-Advance A/S

Industrivej 1

9560 Hadsund

Tel.: 72 18 21 20

E-mail: Salg.dk@nilﬁ sk-alto.com

Web: http://www.nilﬁ sk-alto.dk

FINLAND

Nilﬁ sk-ALTO

Koskelontie 23 E

02920 Espoo

Tel.: (+358) 207 890 605

E-mail: asiakaspalvelu.ﬁ @nilﬁ sk-advance.com

Web: www.nilﬁ sk-alto.ﬁ

FRANCE

ALTO France SAS

26 Avenue de la Baltique, BP 246

91944 COURTABOEUF CEDEX

Tel.: Commercial : 0 825 869 300 - SAV : 0 825

099 585 - Pôle tech : 0 825 802 615

E-mail: info.fr@nilﬁ sk-alto.com

Web: www.alto-fr.com

GERMANY

Nilﬁ sk-ALTO

Division of Nilﬁ sk-Advance AG

Guido Oberdorfer Str. 10

89287 Bellenberg

Tel.: 0180 537 3737

E-mail: info.de@nilﬁ sk-alto.com

Web: www.nilﬁ sk-alto.de

GREECE

Nilﬁ sk-ALTO

8 Thoukididou Str.

164 52 Argiroupolis

Tel.: 210 96 33443

E-mail: nilﬁ [email protected]r

Web: www.nilﬁ sk.gr/

HOLLAND

Nilﬁ sk-ALTO

Division of Nilﬁ sk-Advance BV

Versterkerstraat 5

1322 AN Almere

Tel.: (+31) 36 5460 760

E-mail: info.nl@nilﬁ sk-alto.com

Web: www.nilﬁ sk-alto.nl

HONG KONG

Nilﬁ sk-ALTO

2001 HK Worsted Mills Ind’l Bldg.

31-39 Wo Tong Tsui St.

Kwai Chung

Tel.: (+852) 2427 5951

HUNGARY

Nilﬁ sk-ALTO

2310 Szigetszentmiklos-Lakihegy

II. Rákóczi Ferenc út 10.

Tel.: 24 47 55 50

E-mail: info@nilﬁ sk-advance.com

INDIA

Nilﬁ sk-Advance India Limited

349, Business Point,

No 201,2nd ﬂ oor, above Popular Car World,

Western Express High way, Andheri ( East),

Mumbai - 400 069

Tel.: (+91) 22 321 74592

IRELAND

Nilﬁ sk-ALTO

Division of Nilﬁ sk-Advance Ltd.

Bowerbank Way, Gilwilly Industrial Estate

Penrith, Cumbria CA11 9BQ

Tel.: 01768 868 995

E-mail: sales.ie@nilﬁ sk-alto.com

Web: http://www.nilﬁ sk-alto.ie

ITALY

Nilﬁ sk-ALTO

Strada comunale della Braglia, 18

I-26862 Guardamiglio (LO)

Tel.: 0377 41 4077

Web: www.nilﬁ sk-alto.com/

JAPAN

Nilﬁ sk-ALTO

1-6-6 Kita-shinyokohama, Kouhoku-ku

Yokohama, 223-0059

Tel.: (+81) 45 548 2571

MALAYSIA

Nillﬁ sk-Advance Sdn Bhd

Sd 14, Jalan KIP 11

Taman Perindustrian KIP

Sri Damansara

52200 Kuala Lumpur

Tel.: (+60) 3 603 6275 3120

E-mail: sales@nilﬁ sk-advance.com.my

MEXICO

Nilﬁ sk-Advance de Mexico, S. de R.L. de C.V.

Prol. Paseo de la Reforma 61,

6-A2 Col. Paseo de las Lomas

01330 Mexico, D.F.

Tel.: (+52) 55 2591 1002 (switchboard)

E-mail: info@advance-mx.com

Web: www.nilﬁ sk-advance.com.mx

NORWAY

Nilﬁ sk-ALTO

Bjørnerudveien 24

1266 Oslo

Tel.: (+47) 22 75 17 71

E-mail: info.no@nilﬁ sk-alto.com

Web: www.nilﬁ sk-alto.no

POLAND

Nilﬁ sk-ALTO

05-800 Pruszkow

ul. 3-go MAJA 8

Tel.: (+48) 22 738 37 50

E-mail: info@nilﬁ sk-alto.pl

Web: www.nilﬁ sk-alto.pl

PORTUGAL

Nilﬁ sk-ALTO

Division of Nilﬁ sk-Advance Lda.

Sintra Business Park

Zona Industrial Da Abrunheira

Ediﬁ cio 1,1° A

P-2710-089 Sintra

Tel.: (+35) 808 200 537

E-mail: mkt@nilﬁ sk-advance.es

Web: www.nilﬁ sk-alto.com

RUSSIA

Нилфиск-Эдванс

127015 Москва

Вятская ул. 27, стр. 7

Tel.: (+7) 495 783 96 02

E-mail: info@nilﬁ sk.ru

Web: www.nilﬁ sk.ru

SINGAPORE

Nilﬁ sk-ALTO

22 Tuas Ave 2

Singapore 639453

Tel.: (+65) 6759 9100

E-mail: sales@nilﬁ sk-advance.com.sg

Web: www.nilﬁ sk-advance.com.sg

SPAIN

Nilﬁ sk-ALTO

Division of Nilﬁ sk-Advance S.A.

Torre D’Ara, Paseo del Rengle, 5 Pl. 10

08302 Mataró Barcelona

Tel.: (+34) 902 200 201

E-mail: mkt.es@nilﬁ sk-alto.com

Web: www.nilﬁ sk-alto.es

SWEDEN

Nilﬁ sk-ALTO

Member of the Nilﬁ sk-Advance Group

Aminogatan 18, Box 4029

431 04 Mölndal

Tel.: (+46) 31 706 73 00

E-mail: info.se@nilﬁ sk-alto.com

Web: www.nilﬁ sk-alto.se

TAIWAN

Nilﬁ sk-ALTO

No.5, Wan Fang Road

Taipei

Tel.: (+886) 227 002 268

THAILAND

Nilﬁ sk-ALTO

89 Soi Chokechai-Ruammitr

Viphavadee-Rangsit Road

Ladyao, Jatuchak, Bangkok 10900

Tel.: (+66) 2275 5630

TURKEY

Nilﬁ sk-Advance Profesyonel Temizlik

Ekipmanları Tic. A/S.

Necla Cad. No.: 48,

Yenisahra / Kadıköy

Istanbul

Tel.: (+90) 216 470 08 – 60

E-mail: info-tr@nilﬁ sk-alto.com

Web: http:// www.nilﬁ sk-alto.com.tr

UNITED KINGDOM

Nilﬁ sk-ALTO

Division of Nilﬁ sk-Advance Ltd.

Bowerbank Way, Gilwilly Industrial Estate

Penrith, Cumbria CA11 9BQ

Tel.: 01768 868 995

E-mail: sales.uk@nilﬁ sk-alto.com

Web: www.nilﬁ sk-alto.co.uk

USA

Nilﬁ sk-Advance Inc.

14600 21.st Avenue North

Plymouth, MN 55447-3408

Tel.: (+1) 763 745 3500

E-mail: info@advance-us.com

Web: www.advance-us.com

VIETNAM

Nilﬁ sk-Advance Representative Ofﬁ ce

No. 51 Doc Ngu Str.

Ba Dinh Dist.

Hanoi

Tel.: (+84) 4 761 5642 / (+84) 90426 6368

E-mail: nilﬁ [email protected]

Web: www.nilﬁ sk-advance.com/

Nilfisk-ALTO Neptune 8 Operating Instructions Manual

Marca: Nilfisk-ALTO

Modelo: Neptune 8

Categoría: Limpiadores de alta presión

Tipo: Operating Instructions Manual

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

English: Nilfisk-ALTO Neptune 8

Nilfisk-ALTO Neptune 8 Operating Instructions Manual

Este manual también es adecuado para

Nilfisk-ALTO Neptune 8 Operating Instructions Manual

En otros idiomas

Documentos relacionados

Otros documentos