Panasonic PVD4763S Instrucciones de operación

Categoría
Reproductores de DVD
Tipo
Instrucciones de operación
PV-D4763S
DVD/VCR DECK
Operating Instructions
LSQT0676A
Model No.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Initial Setup
(Connection)
Basic
Operation
VCR
Operation
For Your
Information
DVD
Operation
Connections and Initial Setup Procedures are on pages 12 to 17.
Please read these instructions carefully before attempting to connect, operate or adjust this
product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
®
As an ENERGY STAR Partner, Matsushita Electric Corporation
of America has determined that this product or product model
meets the ENERGY STAR guidelines for energy efficiency.
®
MULTI FORMAT PLAYBACK
*
Ability to play back may depend on recording conditions.
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:471
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from a power source indicated on the
unit or in this manual. If necessary, have your
Electric Utility Service Company or Video Products
Dealer verify the power source in your home.
2 POLARIZED OR GROUNDING PLUG
As a safety feature, this product comes with either
a polarized power cord plug (one blade is wider
than the other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot
fully insert the plug, try reversing it. If it still will not fit,
have an electrician install the proper wall outlet. Do not
defeat the safety feature by tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding
outlet. If necessary, have an electrician install the
proper outlet. Do not defeat the safety feature by
tampering with the plug.
3 POWER CORD
Make sure power cords are routed so that they
are not likely to have anything rest on them, roll
over them, or be in the way of walking traffic.
If an extension cord is used, make sure it also
has either a polarized or grounded plug and that
the cords can be securely connected.
Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified service technician.
Overloaded outlets and extension cords are fire
hazards and should be avoided.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If they are blocked,
heat build-up inside the unit can cause failures that
may result in a fire hazard or heat damage to
cassettes or discs.
For protection, follow these rules:
a. Never cover ventilation slots or the unit while in
use, or operate the unit when placed on a bed,
sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless proper ventilation is provided.
5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS
OR SUDDEN TEMPERATURE CHANGES
Do not place the unit over or near heater or
radiator, in direct sunlight, inside closed vehicles,
in high temperature [over 104°F (40°C)], or in over
75% humidity. If the unit is suddenly moved from
a cold place to a warm one, moisture may
condense in the unit and on the tape causing
damage. Never subject the unit to vibration,
impact, or place it so that the surface is tilted as
internal parts may be seriously damaged.
6 TO AVOID PERSONAL INJURY
Do not place unsecured equipment on a sloping
surface.
Do not place this unit on any support that is not
firm, level, and adequately strong.
The unit could fall causing serious
injury to a child or adult and
damage to the unit.
An appliance and cart
combination should be moved
with care. Quick stops,
excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
Carefully follow all operating instructions and
use the manufacturer's recommended
accessories when operating this unit or
connecting it to any other equipment.
FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY
AND OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON THE UNIT
USING THE UNIT
If the unit has been in storage or moved to a new location,
refer first to the INSTALLATION section of these safeguards.
1
KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug the unit and have it inspected by a
qualified service technician before use.
3 DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time,
disconnect all equipment from the power source as well as
the antenna and cable system.
4 WHEN THE UNIT IS PLUGGED IN
Never expose the unit to rain or water. DO NOT OPERATE
if liquid has been spilled into the unit. Immediately unplug
the unit, and have it inspected by a service technician.
Fire and shock hazards can result from electrical shorts
caused by liquid contact inside.
Never drop or push any object through openings in the unit.
Some internal parts carry hazardous voltages and contact
can cause electric shock or fire hazard.
Do not put any foreign object on the disc tray.
Avoid placing the unit directly above or below your TV set
as this may cause electrical interference. Keep all magnets
away from electronic equipment.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically untreated
cloth to gently remove dust or debris. DO NOT USE cleaning
fluids, aerosols, or forced air that could over-spray, or seep
into the unit and cause electrical shock. Any substance such
as wax, adhesive tape, etc. may mar the cabinet surface.
Exposure to greasy, humid, or dusty areas may adversely
affect internal parts.
SERVICE
1 DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating
instructions, this product does not operate properly, do not
attempt to open or remove covers, or make any
adjustments not described in the manual. Unplug the unit
and contact a qualified service technician.
2 IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified
by the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other hazards.
3
HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as
described in the manufacturers service literature to ensure
that the unit is in safe operating condition.
Important Safeguards and Precautions
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC
- NATIONAL
ELECTRICAL CODE
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded
so as to provide some protection against built up static
charges and voltage surges.
Section 810 of the National Electrical
Code, ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
with respect to proper grounding
of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.
2
KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS
An outside antenna system should be located well away from
power lines, electric light or power circuits and where it will never
come into contact with these power sources if it should happen
to fall. When installing an outside antenna, extreme care should
be taken to avoid touching power lines, circuits or other power
sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.
2
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:472
Region Management Information:
This DECK is designed and manufactured to respond to the
Region Management Information that is recorded on a DVD
disc. If the Region number described on the DVD disc does
not correspond to the Region number of this DECK, this
DECK cannot play this disc.
The Region number for this DECK is 1.
The Player will play DVD-Video marked with labels
containing 1 or ALL.
1
3
ALL
1
2
4
Example:
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage
within the unit may have sufficient magnitude to cause
electric shock.
Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that important literature
concerning the operation and maintenance of this unit
has been included. Therefore, it should be read
carefully in order to avoid any problems.
Safety Precautions/Mesures de sécurité
WARNING: To prevent fire or shock hazard, do not expose this
equipment to rain or moisture.
CAUTION: To prevent electric shock, match wide blade of plug to
wide slot, fully insert.
Avertissement: Afin de prévenir tout risque d’incendie ou de chocs
électriques, ne pas exposer cet appareil à la pluie ou
à une humidité excessive.
Attention: Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de la
prise et pousser jusqu’au fond.
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE
YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
LASER RADIATION
WHEN OPEN DO NOT
STARE INTO BEAM.
ATTENTION:
RAYONNEMENT
LASER EN CAS
DOUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCC NOTE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize
an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the
booklet, Something About Interference available from FCC local regional offices helpful.
FCC Caution:
To assure continued compliance, (example- use only shielded interface cables when connecting to
other devices.) Any changes or modifications not expressly approved by the party responsible for
compliance could void the users authority to operate this equipment.
FCC Warning: Any unauthorized changes or modifications to this equipment would void the users
authority to operate.
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:473
4
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before Using
Accessories
RF Coaxial Cable
LSJA0372
Batteries 2 AA
Remote Control
LSSQ0377
Loading the Batteries
Battery replacement caution
Do not mix old and new batteries.
Do not mix alkaline with manganese batteries.
1) Open cover.
3) Close cover.
2) Insert batteries as
marked.
Only use tapes with the mark in this DECK.
Record/ Playback Time
SP
(Standard Play)
2 Hours
40 Minutes
1 Hour 2 Hours
5 Hours
20 Minutes
2 Hours 4 Hours
LP
(Long Play)
3 Hours 6 Hours 8 Hours
SLP
(Super Long Play)
Type of Video Cassette
Tape Speed
Setting
T160T120T60
Congratulations
on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
years of enjoyment. Please fill in the information
below. The serial number is on the tag located
on the back of your DECK.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
PV-D4763S
Serial No.
To order accessories,
call toll free
1-800-332-5368.
Video Head Clog Sensor
During playback, this screen
appears if clogging is detected.
To remove screen, press PLAY
on the remote or DECK.
Playing older or damaged tapes may eventually cause
video heads to become clogged.
V
I
D
EO HEADS
M
AY
N
EED
CLE
A
N
I
NG
PLEASE
I
NSERT
HEAD
CLE
A
N
I
NG
CASSE
TT
E
OR
REFER
T
O
MANUAL
END
:
P
L
AY
Head Cleaning
Digital Auto Picture
Automatically controls the video output signal for
less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control
(to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise.
Press CH (TRACKING) / on the remote control
or on DECK until the picture clears up.
To return to Auto Tracking, press POWER off, then
on again a few seconds later.
V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) / operate as a
V-Lock control.
Features for a Quality Picture (VCR)
Built-in Head Cleaner
A clean video head helps produce a clear picture.
So, we have equipped your DECK with a built-in,
non-chemical head cleaning system that helps
prevent clogging of the video heads.
Cleaning is performed each time you load or unload
a video cassette.
This feature is preventative only, If your video heads
are seriously clogged, consider the use of a chemical
non-abrasive head cleaning kit or take your DECK to
a Servicenter.
Use dry type head cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
If head clog symptoms persist, contact your
nearest servicenter by visiting our Web Site
(see p. 65).
R
R
R
R
R
R
R
R
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:474
5
Table of Contents
Timer Recording..............................................................24, 25
MTS Broadcast/ VHS Hi-Fi Stereo System ....................26, 27
Multi-Brand Control Feature ...........................................28, 29
Tape Operation (Search System) .......................................30 ~ 32
Special VCR Features .....................................................33, 34
Copying Your Tapes (Dubbing) .........................................................35
Disc Operation ...............................................................36 ~ 41
DVD-RAM Operation (DVD-RAM only).................................42, 43
DVD Operation using On-Screen Displays .................44 ~ 48
MP3/WMA/JPEG Playback Operation ..........................49 ~ 51
DVD Lock Feature .................................................................52
Settings for DVD Operation ..........................................53 ~ 57
SD Card............................................................................58, 59
Language Code List..............................................................60
DVD / VCR
Warning and Instruction Displays........................................61
Before Requesting Service.............................................62, 63
Limited Warranty .............................................................64, 65
Customer Services Directory ...............................................65
Spanish (Español) Quick Use Guide............................66 ~ 71
Index..................................................................................... BC
DVD / VCR
Important Safeguards and Precautions ............................2, 3
Before Using............................................................................4
DECK / Disc / Cassette Information .................................. 6 , 7
Location of Controls .......................................................8 ~ 10
Displays (On Screen Displays and Multi Function Display) ....................11
Connections ..................................................................12 ~ 15
Initial Setup for Basic Connections (Ready to Play) ..........16, 17
VCR
Reset Language, Channels, Clock, VCRs Output Channel ...18, 19
Playback/ Record on a Tape...........................................20, 21
DVD
Basic DVD Operation ......................................................22, 23
Initial Setup
(Connection)
Basic
Operation
VCR
Operation
For Your
Information
DVD
Operation
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:475
6
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DECK / Disc / Cassette Information
Prevent Accidental Tape Erasure
Record Tab
Cover the hole
with cellophane tape.
To record again
Break off the tab to
prevent recording.
Screw driver
Cleaning DECK
Use a soft cloth or dusting attachment of a vacuum
cleaner to remove dust from the ventilation holes on
the back sides and bottom of the cabinet. Plastic
surfaces are easily scratched and can be marred
by alcohol and various solvents. Avoid excessive
use of oil-based furniture polishes since the
materials used in the cabinet will accumulate more
dust. We recommend using a non-abrasive,
antistatic cleaner and polisher.
DVD-RAM discs
DVD-RAM discs must meet the following conditions
for this unit to be able to play them.
Type
Non-cartridge discs
Discs that can be removed from
their cartridges (TYPE 2 and 4)
Capacity
12 cm (5) 9.4 GB (double-sided)
and 4.7 GB (single-sided)
8 cm (3) 2.8 GB (double-sided)
Remove TYPE 2 and 4 discs from their cartridges
before use, then return them when you are finished.
Read the instructions for the disc carefully.
Some parts of the disc, for example where one program
ends and another begins, may not play smoothly.
DECK can play back discs bearing any of the
following marks:
Discs which cannot be played
DVD with Region No. other than 1 or ALL
PAL discs (the audio on DVD-Audio can be
played), DVD-ROM, DVD-RW, DVD+RW,
CD-ROM, CDV, CD-G, CVD, SVCD, SACD,
Divx Video Disc and Photo-CD
[Discs Played 8cm (3") or 12cm (5")]
DVD (DVD-Video)
Video CD
CD (CD-DA)
CD-R/CD-RW (CD-DA,Video
CD formatted discs [finalized])
WMA, MP3, JPEG
DVD-Audio
Logo Disc type
DVD-R (DVD-Video formatted
discs [finalized])
Disc formats supported by this DECK
DVD-RAM (Version 1.1 of the
Video Recording Format a
unified video recording
standard)
Notes
Do not use irregularly shaped discs (e.g. heart-
shaped), as these can damage the unit.
It may not be possible to play CD-R, CD-RW,
DVD-R and DVD-RAM in all cases due to the
type of disc or condition of the recording.
If disc is brought from a cold to a warm
environment, moisture may form on the disc
Wipe away moisture with a soft, dry, lint-free cloth
before using disc. (See above.)
Improper disc storage
Discs could be damaged if stored or left in areas:
exposed to direct sunlight.
that are humid or dusty.
near heat (i.e. heater, radiator, etc.).
Disc Handling
To clean disc surface
With a soft, damp (water only) cloth,
gently wipe from the center hole to the
outer edge as shown below. (Wiping in a
circular pattern will scratch the surface.)
DVD-RAM, DVD-R :
Clean only with the DVD-RAM disc
cleaner available. Never use cloths or
cleaners for CDs etc.
Handling precautions
Sticking a label on the disc may impair DVD-R playback.
Do not attach sticker to discs. (Do not use discs with
exposed adhesive from tape or left over peeled-off
stickers.)
Only hold disc by edges as shown below. Fingerprints,
dirt and scratches can cause skipping and distortion.
Do not write on label side of disc.
Never use record cleaning
sprays, benzine, thinner,
static electricity prevention
liquids, or any other solvent.
Do not try to close disc tray when disc is not
properly placed.
Disc tray
Disc
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:476
7
Power Source: 120 V AC, 60 Hz
Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts
Video Signal: EIA Standard NTSC color
Video Recording System: 4 rotary heads helical scanning system
Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)
Tuner:
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125
Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output
Input Terminal: Audio/Video Line Input (Front)
Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)
Audio Output 2 (L), (R)
Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight: 4.9 kg (10.8 lbs).
Dimensions: 430 (W) x 95.5 (H) x 344 (D) mm
16-15/16 (W) x 3-12/16 (H) x 13-9/16 (D) inch
Discs Played
(1) DVD-Video Disc 5 (12 cm) single-sided single-layer
DVD-Audio Disc 5 (12 cm) single-sided double-layer
5 (12 cm) double-sided double-layer (one layer per side)
3 (8 cm) single-sided single-layer
3 (8 cm) single-sided double-layer
3 (8 cm) double-sided double-layer (one layer per side)
DVD-RAM Disc 5 (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)
3 (8 cm) 2.8 GB (double-sided)
(2) Compact Disc 5 (12 cm) disc
(CD-DA, Video CD) 3 (8 cm) disc
(CD-R/CD-RW, MP3, WMA, JPEG)
Digital Audio Output: Digital Optical Connector
Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)
Laser power: CLASS II
Specifications
Note: Designs and specifications are subject to change without notice.
Definition of Terms (DVD)
Angle: Some DVD discs feature scenes simultaneously shot from different angles.
The ANGLE button can be used to view the scene from different angles.
(ANGLE Indicator lights on DECK when a scene recorded at different angles
is detected.)
Chapter Number: Titles are subdivided into numbered sections. You can quickly search for
a favorite scene using these numbers.
DVD: A high-density optical disc on which high-quality pictures and sound have
been digitally recorded. DVD incorporates new video compression technology
(MPEG II) and high-density recording technology which allow entire movies to
be recorded with incredible playback quality.
Playback Control: With Video CD (version 2.0), scenes or information may be selected for viewing
or listening from an interactive menu that appears on the TV screen.
Subtitles: Written dialogue which appears at the bottom of the screen.
Time Number: The elapsed play time from the start of a disc or title. Use to quickly find
scenes. (May not work with some discs.)
Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.
Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to
be quickly located.
Video CD: CD containing picture and sound with same quality level as video tape.
This DECK also supports Video CDs with playback control (version 2.0).
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093,
licensed for limited viewing uses only.
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Initial Setup
(Connection)
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:477
8
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Location of Controls
Remote Control
Bold: VCR Function
Italic
:
DVD Function
Bold Italic
:
VCR and DVD Functions
Normal: Others
EJECT button: When this button is pressed in VCR mode, the tape is ejected.
This button is inoperative if pressed during recording.
If pressed in DVD mode, the disc tray opens or closes.
ZOOM
p
. 37
POWER
DSS
/
CABLE mode
p. 28
SPEED
/
PAGE
pp. 21,
41
NUMBER keys
TV mode
p. 28
EJECT
/
OPEN
/
CLOSE
pp. 20,
22
ACTION
pp. 18
, 53
PAUSE
/
STILL
pp. 20,
23
COUNTER
RESET
p. 32
PROGRAM
p. 24
RECORD
p. 21
ADD/DELETE
/
CLEAR
pp. 19,
39, 52
VCR mode
p. 28
VOLUME
+
/
-
p. 28
CHANNEL
/
TRACKING
/
V-LOCK
pp. 4, 21
PLAY
pp. 20,
22
REWIND
/
SEARCH
/
SLOW-
pp. 20,
23
DVD mode
p. 28
INPUT
p. 35
COMMERCIAL SKIP
/
ZERO SEARCH
pp. 31, 32
DISPLAY
pp. 11,
44
STOP
pp. 20,
22
ANGLE
p
. 37
SUB TITLE
p
. 36
VCR/TV
p. 21
RETURN
/
SEARCH
pp
. 22,
30
AUDIO
(SAP / Hi-Fi)
pp. 27,
36
SELECT
SKIP
SKIP
p
. 23
FAST FORWARD
/
SEARCH
/
SLOW+
pp. 20,
23
TITLE
/
Direct Navigator
pp.
38, 42
MENU
/
Play List
pp.
38, 43
SET
Virtual Surround Sound (V.S.S.)
/
ENTER
pp
.
23,
28
TAPE POSITION
/
VOLUME ADJUST
pp. 34,
40
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:478
9
Initial Setup
(Connection)
Front View of DECK
Audio/Video
Input Connector 2
(LINE 2)
p. 35
CHANNEL /
TRACKING/V-LOCK
pp. 4, 21
POWER
PAUSE
p.
23
OPEN/CLOSE
p.
22
STOP/EJECT
p. 20
Multi Function
Display
p. 11
REC
p. 21
Disc Tray
Cassette
Compartment
PLAY
p. 20
Remote
Sensor
FAST FORWARD/SEARCH
p. 20
REWIND/SEARCH
p. 20
Front View of DECK
SKIP
SKIP
p.
23
STOP
p.
22
Bold: VCR Function
Italic
:
DVD Function
Bold Italic
:
VCR and DVD Functions
Normal: Others
PROGRESSIVE
p. 10
PLAY
p.
22
SD Card slot
p. 58
If the disc cannot be removed...
First, unplug DECK. Then, prepare a rigid
wire (e.g. an extended paper clip) and,
applying moderate force, insert it straight
into the hole at the base of the tray.
The tray will eject a little. Now, pull the tray
all the way out and remove the disc.
Over 2 inches
Use when moving DECK to new location, or if a mistake was made in the Initial
Setup section (return to Factory Setting).
Make sure a tape is not inserted in the DECK.
Reset All Memory Functions
Press and hold both VCR PLAY
and CHANNEL
on the DECK for
more than 5 seconds.
The power shuts off.
Turn DECK Power on.
3
Do Initial Setup (Ready to Play)
on page 16.
2
1
21
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:479
10
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Location of Controls (continued)
Rear View of DECK
AC Power Plug
S-Video Out
Connector
(DVD Only)
pp.
10, 13
Component Video Output
Connector (Y, P
B
, P
R
) (DVD Only)
p.
13
Audio Output 2
Connector (L/R)
p.
13
Optical Digital Audio
Output Connector
(DVD Only)
p.
15
Video Input
Connector
p. 35
Video Output
Connector
p.
12
Audio Output 1
Connector (L/R)
p.
12
VHF/UHF Antenna Input Terminal
p. 12
VHF/UHF Antenna Output Terminal
p. 12
While plugged into an AC outlet,
this DECK consumes 4 W of
electrical power in off mode.
••
The following table shows the status of the output jacks when in VCR or DVD mode.
Bold: VCR Function
Italic
:
DVD Function
Bold Italic
:
VCR and DVD Functions
Note
PROG functions on the remote are not available when using Component Video Output
and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press
PROG.
Video Output
Audio Out 1
Audio Out 2
Component
Video Output
S-VIDEO OUT
VCR
DVD
YES
YES
N/A
N/A
To enjoy PROGRESSIVE SCAN video
(1).Connect
Component Video Output
to the component video input terminals of a television.
(See p. 13.)
(2).When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the
PROGRESSIVE SCAN signal is output from the
Component Video Output Connector
.
Notes
The PROGRESSIVE button can be operated when the DECK is in DVD function mode.
The screen may shift off-center when using progressive output. Please adjust the screen
position if this occurs. (Refer to your TV manual.)
The DECK outputs video signals (not PROGRESSIVE SCAN) from the VIDEO OUT and
S-VIDEO OUT terminals when the ON lamp is lit.
YES
Audio Input
Connector (L/R)
p.
35
5.1ch Analog Audio Output
Connector (CENTER, SUB WOOFER,
SURROUND L/R, FRONT L/R)
(DVD Only)
p.
15
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4710
11
VCR
TIMER REC
Hi
-
Fi
DIGIT
DIGIT
AL
CD
DVD
MP3
WMA
AM
PM
ANGLE
REC
1
2
:
0
0
A
M
0
:
25
CH
02
-
0
:
1
2
:
3
4
SP
S
T
ER
EO
SAP
M
ONO
VCR Status & Clock Displays
Blank Tape/ No Video Signal
Indications
Whenever a blank section of a tape
comes up in Play mode, or when the
selected channel has no broadcast
signal with Weak Signal Display
Feature (p. 33) set to OFF, the TV
screen will turn solid blue.
Function Status
Rec Time Remaining
(OTR mode only,
see p. 21.)
Current Time
Channel
Tape Speed
(See p. 4.)
Broadcast Audio
Being Received
(See p. 26.)
When a function button
is pressed, e.g. PLAY,
or you change
channels, a 5-second
display appears.
Counter
Displays (On Screen & Multi Function)
To display or remove
overlay at right,
press DISPLAY.
Multi Function Display
On Screen Displays (VCR)
Function & Channel Displays
CH 0
8
VCR mode Indicator
Lights up when
DECK is VCR mode.
Hi-Fi Indicator
Lights up when
Hi-Fi audio is
monitored in Play
mode.
Timer Indicator
Lights up when
DECK is set for
Timer Recording,
or when One
Touch Recording
(OTR) is used.
Flashes when
Timer Recording is
set, but a tape has
not been inserted
into DECK and
when a power
interruption occurs
during Timer
Programming.
VCR REC Indicator
Lights up during
recording.
DTS Indicator
Lights up when DTS
formatted DVD is played.
(DVD only)
Dolby Digital
Indicator
Lights up when Dolby Digital
formatted DVD is played.
(DVD only)
Clock/ Status/ Channel/ Speed Display
Displays the current time. Briefly displays DECK
status when a function button is pressed. Briefly
displays the channel number, or L1 or L2
when a channel or line input is selected. Briefly
displays the recording speed when SPEED is
pressed.
DVD mode Indicator
Lights up when
DECK is DVD mode.
AM/PM
Indicator
Initial Setup
(Connection)
ANGLE Indicator
Lights up when a
scene recorded at
different angles is
detected.
(See p. 37.)
(DVD only).
CD/MP3/WMA
Indicator
CD
:Lights when a
Video or Audio
CD is inserted.
MP3/WMA :
Lights when an
MP3 or WMA
file is played.
Tape Indicator
Lights up when a tape
is inserted.
DISC Indicator
Lights up when a
disc is inserted.
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4711
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections
1 Disconnect antenna or cable from TV
and connect to DECK.
WARNING
When using Nut type RF coaxial cables, tighten with
fingers only. Overtightening may damage terminals.
Basic Connections
Connect DECK and TV with an RF Coaxial Cable
a
(supplied) or an AV Cable
b
(not supplied) as shown in the figure below.
If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher
quality picture and sound.
You can enjoy stereo sound even if your TV is not stereo by connecting a stereo
amplifier to DECK.
IN
FROM
ANT.
OUT
TO
TV
AUDIO
IN 1
OUT
DVD/VCR DECK
VHF/UHF
R
L
VIDEO
VHF/
UHF
VIDEO
IN
AUDIO IN
R
L
TV
AV CABLE
(not supplied)
2 Connect DECK to TV with RF Coaxial Cable.
a
b
DSS
Receiver
OUT
IN
IN
Note to CABLE system installer
This reminder is provided to call the CABLE system installers attention to Article 820-40 of the
NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as practical.
OUT
IN
Antenna or Cable
Cable Box
or
DECK TV
DSS Receiver DECK TV
Cable Box DECK TV
RF COAXIAL CABLE
(supplied)
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4712
13
You CannotYou Can
record and view
both scrambled
and unscrambled
channels if
additional
equipment is
added.
This connection
requires: two
converter boxes,
an A/B switch,
and a 2-way
splitter.
view a channel
other than the
one selected
for any type of
recording.
do a Timer
recording of a
channel unless
you select it on
the Cable Box.
IN
FROM
ANT.
OUT
TO
TV
IN 1
VHF/UHF
OUT
IN 2IN 1
Cable Box
OUTIN
OUT 2
OUT 1
2-Way Splitter
OUT
A/B Switch
IN
Connect With Two Cable Boxes
IN
FROM
ANT.
OUT
TO
TV
IN 1
VHF/UHF
OUT
Cable Box
OUTIN
IN
R
L
OUT
TV
VIDEO
AUDIO
ANT or CATV
You CannotYou Can
record
scrambled
channels.
view any
(including
scrambled)
channel.
use Remote
Control to select
channels without
using Multi-brand
control feature.
ANT
or
CATV
IN
VIDEO
AUDIO
R
L
OUT
TV
Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT
or S-VIDEO mode).
If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.
If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to
S-VIDEO OUT.
When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.
Connections For DVD Only (enjoying higher picture quality)
Other Connections
Notes
DVD/VCR DECK
DVD/VCR DECK
VHF/
UHF
Cable Box
VHF/
UHF
With a Cable Box (DECK
Cable Box TV)
2
1
3
Initial Setup
(Connection)
You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,
and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only
from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.
PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT
Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.
TV must have capability to accept and display a progressive scan signal to use
PROGRESSIVE mode. Consult your TV operating instructions.
VIDEO
AUDIO
R
L
TV
COMPONENT
VIDEO OUT
AUDIO OUT2
S-VIDEO OUT
DVD OUTPUT
Y
P
B
P R
R
L
IN
Y
PB
PR
S-VIDEO
IN
R
L
IN
From DECKs
A/V OUTPUT
DVD/VCR DECK
or
IN
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4713
14
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections (continued)
Audio Connections
Ready Checklist
Turn down the volume, then turn DECK, as well as other equipment to be connected,
off before proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them so that air can
circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when connecting audio and video cables.
Connecting Amplifier (2ch stereo system)
Speaker
Amplifier
Speaker
AUDIO OUT2
AUDIO IN
R L
L
R
DVD/VCR DECK
Notes on audio output from the optical digital audio output connector
Enjoying digital audio output from the digital audio output connector
*1 The type of audio output from the connector can be selected by the Settings for DVD
Operation. (See p. 54.)
*2 Sound having 96/192 kHz sampling is converted into 48 kHz sampling (or 88.2/176.4 kHz
sampling is converted into 44.1 kHz sampling) when it is output from the DECKs optical digital
audio output connector.
For your reference:
Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories
Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel)
sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.
Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,
DVDs are recorded in 44.1 kHz/16 bit ~ 192 kHz/24 bit.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674,
5,974,380, 5,978,762 and other world-wide patents issued and pending. DTS and DTS Digital
Surround are registered trademarks of Digital Theater Systems, Inc. Copyright 1996, 2000
Digital Theater Systems, Inc. All rights reserved.
Disc
DVD
Video CD
CD
MP3
WMA
Sound recording format
Dolby Digital
Linear PCM
(48/96/192/44.1/88.2/
176.4 kHz 16/20/24bit)
DTS
MPEG 1
Linear PCM
MP3
WMA
Optical digital audio output from connector
Dolby Digital bitstream (1 - 5.1 ch)
or PCM (48 kHz sampling/16 bit only)*
1
Linear PCM (2 ch)
(48 kHz sampling/16 bit or 44.1 kHz sampling/
16 bit)*
2
Bitstream or PCM (48 kHz sampling/16 bit only)*
1
PCM (44.1 kHz sampling)
Linear PCM (44.1 kHz sampling)
Linear PCM (It depends on the MP3 file)
Linear PCM (It depends on the WMA file)
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4714
15
Enjoy the powerful movie theater and hall-like sound available with multiple
channel audio found on DVDs by connecting an amplifier and speakers.
There are two types of connection, digital and analog.
Caution for optical digital audio output connector:
When connecting an amplifier (with an Optical Digital Input Connector) which does not
contain the Dolby Digital or DTS decoder, be sure to select PCM at Dolby Digital
and PCM at dts of the Settings for DVD Operation Audio Output (see p. 54).
Otherwise, any attempt to play DVDs may cause such a high level of noise that it may
be harmful to your ears and damage your speakers.
When a Dolby Digital/DTS decoder is connected, please select Bitstream at dts or
Dolby Digital of the Settings for DVD Operation Audio Output.
If PCM is selected, there will be stereo sound. (See p. 54.)
Video CDs and CDs can be played as usual.
Note:
Some DTS decoders which do not support DVD-DTS interface may not work properly with
DECK.
Connecting Amplifier (5.1 ch Surround system)
A.Digital connection (DECK OPTICAL Digital Audio Output Connector)
When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS
bitstream is output from the DECK OPTICAL Digital Audio Output Connector. When DECK
is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality
audio in your home. [An optical digital audio cable (optional) is required when an optional
Dolby Digital decoder or DTS decoder is used.]
B.Analog connection (5.1 ch Analog Audio Output Connector)
Connect an amplifier with multi-channel audio input terminals. This DECK can decode
Dolby Digital and DTS. There are no limitations on sampling frequency with this kind of
connection.
Initial Setup
(Connection)
DVD/VCR DECK (Rear)
Decoder with Dolby
Digital /DTS processing
Optical Digital Audio
Cable (optional)
To Optical Digital Audio
Input Connector
Notes on connecting an optical
digital audio cable (optional)
Firmly connect the cable to the
connector.
A.Digital connection
Front
Speaker
Front
Speaker
Surround
Speaker
Surround
Speaker
Center
Speaker
Subwoofer
B.Analog connection
Amplifier
To multi-channel audio
input terminals
[5.1 ch Surround system]
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4715
16
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before doing Initial Setup
Initial Setup for Basic Connections (Ready to Play)
Turn TV on.
See connections
a
RF Coaxial Cable Connection and
b
AV Cable Connection on page 12.
<RF Coaxial Cable Connection>
Set TV to channel 3.
<AV Cable Connection>
Set TV to VIDEO.
[DECK
TV]
Go to Initial Setup (Ready to Play). (See below.)
[Cable Box
DECK
TV], [DSS
DECK
TV]
Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel
in your time zone.
If you use a DSS Receiver, it must be turned off.
2
1
3
Press VCR on remote for VCR mode.
Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel
and clock set starts.
If screen below does not appear, check DECK - TV connection and, if TV is tuned to
channel 3, try switching it to channel 4.
To change VCRs output channel, please refer to VCRs Output Channel on page 19.
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
CH AUTO SET PROCEEDING
CANCEL : STOP
Plugging the AC Power Plug into
an AC outlet
Initial Setup (Ready to Play)
2
1
Function buttons are inoperative during Initial Setup.
To remove a cassette during Auto Set, press EJECT on
the remote or STOP/EJECT twice on the DECK.
In this case, settings must be made manually. (See p. 18.)
Depending on conditions, Auto Clock Set may take longer
than 30 minutes. If so, press STOP to stop setup and
perform settings manually. (See p. 18.)
Notes
Continued on next page...
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4716
17
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
Settings are made automatically.
When setup is done, this screen appears.
If AUTO CLOCK SET IS INCOMPLETE
appears, manually set clock. See below.
3
6
/
8
/
20
03
SUN
2
:
20P
M
D
S
T
:
ON
SETT
I
N
G
: CH
10
AUTO CLOCK SET
C
O
M
PLETED
If Auto Clock Set was incomplete.
Press ACTION* on remote to display
CLOCK screen.
Press
to select the month and SET to
set. In the same manner, select and set the
date, year, time, and DST (Daylight Saving
Time).
Press ACTION to start clock and exit.
S
ET
:
S
ET BACK :
ST
A
RT
:
ACT
I
O
N
D
ST
:
ON
6
/
8
/
2003
SUN
2
:
2
0
P
M
SET
CO
M
P
L
E
T
E
D
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
SET
C
L
OC
K
Manual Clock Set
1
2
3
AUTO CLOCK SET IS
I
NC
O
M
PLETE
PLEASE SET CLOCK BY
PRESSING
ACT
I
ON KEY
DST
:
O
N
SE
L
E
C
T
M
O
N
TH
TH
1
/ /
:
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
SET
C
L
OC
K
VCR
ACTION
SET
SELECT
Initial Setup
(Connection)
EJECT
STOP
dy to Play)
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4717
18
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Clock
2) Press to select
MANUAL, and press SET.
(For Auto Clock Set, select
AUTO CLOCK SET.)
3) Press and to
select, then set the date,
time, and DST (Daylight
Saving Time).
4) Press ACTION to start
Clock and exit this
mode.
(TIME ZONE ADJUST
appears only when auto
clock is set.)
SEL.
:
QUITTER
: ACTION
REGLER:SET
MENU
REGLAGE MAGNETOSCOPE
REGLAGE HORLOGE
REGLAGE CANAL
SD CARD LECTURE
LANGUAGE/IDIOMA:FRANÇAIS
CA SORTIE : 3
ELEGIR
:
SALIR
: ACTION
FIJAR : SET
MENU
PREPARAR VCR
FIJAR RELOJ
FIJAR CANAL
SD CARD REPRODUCCION
LANGUE/LANGUAGE:ESPAÑOL
CANAL DE SALIDA : 3
SELECT
:
EXIT
: ACTION
SET:SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
Language
2) Press SET repeatedly to
change language item as
shown below.
For English
For Spanish
For French
1) Press to select
language item.
Reset Language, Channels, Clock, VCRs
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
Channels
2) Press to select
ANTENNA, then
press SET to set your
antenna system
(TV or CABLE.)
3) Press to select
AUTO SET, then
press SET.
If you use a Cable Box,
set it to the PBS channel
in your time zone.
After Channel Auto Set
is finished, Auto Clock
Set will be performed.
1
2
Press ACTION*
to display MENU.
SELECT
:
EXIT
: ACTION
SET:SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
3) Press ACTION to exit.
SELECT :
EXIT
: ACTION
SET:SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
ANT
ENN
A
:
CABLE
A
U
T
O
S
E
T
W
EA
K
S
I
GN
AL
D
I
SPLA
Y
:
OFF
C
ABLE
/
DSS
B
O
X SET UP
V
CR
Plus
+
C
H SET UP
SET UP
CH
A
NNE
L
AUT
O
C
L
OC
K SET
M
A
NUNU
AL
T
I
M
E
ZO
N
E
A
D
JUS
T
:
0
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
SET
C
L
OC
K
D
ST
:
ON
6
/
8
/
20032003
SUN
1212
:
0
0
P
M
SELECT
H
OUROUR
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
SET
C
L
OC
K
SELE
C
T
:
SET
:
SET BACK :
EXIT
:
ACT
I
O
N
1) Press to select
SET UP CHANNEL,
and press SET.
1) Press to select
SET CLOCK, and
press SET.
PROGRAM functions are not available
when using COMPONENT Video Output
and S-VIDEO OUT. Please set TV to
either RF INPUT or VIDEO INPUT, and
then press PROGRAM.
CH AUTO SET PROCEEDING
CANCEL : STOP
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4718
19
Add or Delete a Channel
To add channel:
Select channel with NUMBER keys
and press ADD/DLT.
To delete channel:
Select channel with CH / or
NUMBER keys and press ADD/DLT.
C
HANNEL
08
ADDED
C
HANNEL
08
DE
L
E
T
ED
Time Zone Adjust
2) Press to select
TIME ZONE ADJUST,
VCRs Output
Channel
1) Press to select
VCRS OUTPUT CH.,
and press SET.
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
2) Press SET.
3) Press ACTION.
After 3 seconds
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
To Make Corrections,
repeat steps 1) ~ 3).
DST (Daylight Saving Time)
DECK auto adjusts clock for DST.
(p. 17.)
Spring (First Sunday in April)
DST:ON
Sets clock ahead one hour.
Autumn (Last Sunday in October)
DST:ON
Turns clock back one hour.
If your area does not observe
Daylight Saving Time, select
DST:OFF.
Keep these time changes in mind
when programming DECK for
timer recordings.
1) Press to select
SET CLOCK, and
press SET.
and press SET to
subtract or add hour(s)
as necessary.
*Important: If a remote control button does not work
when pressed, press the VCR button
on the remote and try the button again.
(Only when Auto Clock is set.)
3) Press ACTION twice.
•“TIME ZONE ADJUST
returns to 0 if clock is
set manually.
I
F
YOU
PRESS
ACT
I
O
N
KEY, VCR
S
O
UTPUT
CH
S
W
I
TCHES
T
O
CH
4
.
PLEASE
TUNE
Y
O
UR
TV
TO
CH
4
.
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
SET
C
L
OC
K
AUT
O
C
L
OC
K SET
M
A
NU
AL
T
I
M
E
ZO
N
E
A
D
JUS
T
:
0
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
ADD/DLT
NUMBER
keys
POWER
ACTION
CH
/
VCR
SET
SELECT
Basic
Operation
k, VCRs Output Channel
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4719
20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Playback/ Record on a Tape
Insert a tape.
21
Playback using DECK buttons
Press PLAY.
Multi Function Display
Press STOP/EJECT to stop
and/ or eject a tape.
Ready Checklist
All connections are made. (pp. 12 ~ 15)
TV and DECK are plugged in.
TV is on and tuned to CH 3, 4, or VIDEO.
Remote is in VCR mode. (Press VCR.)
Insert a tape.
DECK power comes on. If Auto VCR/TV (see
p. 32) is set to OFF, press VCR/TV on the
remote to be VCR mode.
If tape has no rec. tab (p. 6), auto play begins.
Special Features During Play
1
2
3
Press REW/SLOW- or FF/SLOW+ in Stop
mode to rewind or fast forward a tape.
Press EJECT on remote, or STOP/EJECT
on DECK to eject a tape.
Press STOP to stop a tape.
Press PLAY* to play a tape.
Forward/Reverse Scene Search
Press FF/SLOW+ or REW/SLOW-.
Press PLAY to release.
After search has begun, each additional press of
FF or REW changes speed as shown below.
[SLP] : Approx. 21X
Approx. 9X
[LP] : Approx. 9X
Approx. 7X
[SP] : Approx. 7X
Approx. 3X
If at 21X, 9X, or 7X speed the picture is
interrupted, change speed to 9X, 7X, or 3X.
Still (Freeze) Picture
Press PAUSE/STILL.
Press PLAY to release.
Frame by Frame Picture
Press PAUSE/STILL in Still mode.
Press PLAY to release.
Slow Motion Picture
Press FF/SLOW+ (increase speed) or
REW/SLOW- (decrease speed) in Still
mode.
Press PLAY to release.
Playback a Tape
Picture interruption may occur with some TVs.
FF and REW search speed may vary
depending on current tape position.
Notes
These features work best in SP or SLP mode.
The sound will be muted.
To reduce picture noise, see Manual Tracking
Control on page 4.
After DECK is in Still or Slow mode for 3 minutes,
it will switch to Stop mode automatically to
protect the tape and the video head.
Notes
PAUSE/
STILL
REW/SLOW-
STOP
FF/SLOW+
EJECT
CH /
SPEED
REC
VCR/TV
PLAY
DVD
VCR
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4720
21
Insert a tape with a record tab (p. 6).
1
DECK power comes on. If Auto VCR/TV (see p. 32)
is set to OFF, press VCR/TV on the remote to be
VCR mode.
5
4
2
3
Press CH , or NUMBER keys
to select the channel.
For LINE input, see p. 35.
If channel is over 100, press 100 key then press
the remaining 2 digits.
Press SPEED
to select the record speed (p. 4).
SP = Standard Play LP = Long Play
SLP = Super Long Play
Press REC
to start recording.
(The VCR REC indicator lights up on Multi Function
Display),
To edit out unwanted scenes, press PAUSE/STILL
to pause, and again to resume recording.
You cannot view another channel during recording.
Press STOP
to stop recording.
It is not possible to record from DVD/ Video
CD/ CD to VHS tape using DECK.
Watching one channel and recording another
is not possible when using Cable Box or
DSS Receiver.
After 5 minutes in Pause mode, DECK stops to
protect a tape and video heads.
Speed appears on-screen and on Multi Function Display.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
Record on a Tape
Remove loose or peeling
labels from tapes to prevent
tape jam.
Multi Function Display
Record using DECK buttons
4
2
Select
Channel.
Press REC
to start
recording.
Press STOP/EJECT to stop.
This video recorder, equipped with HQ
(High Quality) system, is compatible
with existing VHS equipment. Only use
tapes with the mark. Only tapes
tested and inspected for use in 2, 4, 6,
and 8 hour machines are
recommended.
Normal Rec
0:30 1:00
1:302:003:004:00
1
Insert a tape.
Note
Notes
One Touch Recording (recording in progress),
press REC repeatedly to set the recording length
(30 min. ~ 4 hours).
DECK shuts off after the preset record length.
Record one station, watch another,
press VCR/TV on the remote
(change to TV mode),
select channels at TV (recording continues).
Select Channels at DECK (In STOP or
REC. PAUSE mode),
press VCR/TV on the remote
(change to TV mode),
select channels at DECK.
Play a disc while recording a tape.
insert a disc during recording,
press
DVD
, and then press
PLAY
.
Basic
Operation
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4721
22
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Basic DVD Operation
Ready Checklist
All connections are made. (pp. 12 ~ 15)
DECK is plugged in.
If DECK is connected to an audio amplifier,
turn the stereo systems power on.
*
1
Interactive DVD...
May include multiple camera angles,
stories, etc.
*
2
Video CD with playback control...
Particular scenes or information can be
interactively selected from a menu that
appears on the screen.
Operation using DECK buttons
Press PLAY.
Insert a disc.
Press
OPEN/CLOSE.
Press STOP.
6
Press
POWER.
4
1
3
3, 7
5
Press or
NUMBER keys
(see
below) to select title,
and press
SET
or
PLAY
to start playing.
1
Press
POWER*
on the remote or DECK.
Press
DVD
to select DVD mode.
Press
OPEN/CLOSE
,
and then place a disc into the disc tray.
2
3
If a disc is already inserted, go to step 4.
(Depending on the disc, playback may
start automatically.)
Press
PLAY
to start playing.
Disc tray closes automatically.
4
If an interactive DVD*
1
or
a Video CD with playback
control*
2
is used and TITLE
MENU appears, go to step 5.
You may also close tray by
pressing
OPEN/CLOSE
.
Data reading time differs with
each disc.
Using NUMBER keys starts playing automatically.
The number of available titles varies with each disc.
1 digit number 1 ••• 1
2 digit number 12 ••• 10 1 2
3 digit number 123 •••100 1 2 3
Press
SKIP
| or | to go to next or previous
menu screen.
SKIP function not available with all discs.
Please refer to disc jacket for operation information.
<Example1>
<Example2>
To return to menu (play stops)
Press
TITLE, MENU,
or
RETURN
. (DVD-Video/
DVD-Audio)
Press
RETURN
. (Video CD)
Press
STOP
to stop playing.
6
7
Press
OPEN/CLOSE
to eject the disc.
Hold disc by its edges
only (p. 4) with printed
side up and use guides
to place into tray.
Use 3 (8 cm)
or 5 (12 cm) disc.
CLOSE
READING
T
I
TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
•“Pressing
SET
or
PLAY
is not necessary when
using
NUMBER keys.
<Input
Example>
OPEN/
CLOSE
10
MENU
SET
FF/
SLOW+
STOP
RETURN
POWER
REW/
SLOW-
NUMBER
keys
TITLE
PLAY
DVD
PAUSE/
STILL
SELECT
VSS
SKIP
SKIP
1
2
1
2
DVD-RAM see p. 42
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4722
23
Forward/Reverse Scene Search
Press
FF/SLOW+
or
REW/SLOW-
during play.
Press
PLAY
to release.
Starting forward/reverse search during play
started from menu on Video CDs may recall menu.
Search speed, slow at first, increases with each
additional press of the button up to 5 levels.
Forward/Reverse Chapter/Track Skip
Press
SKIP
| or |
SKIP
during play.
Each press skips a chapter (DVD-Video) or
track (DVD-Audio/Video CD/CD).
Pressing |
SKIP
once midway through a
chapter/track returns to the start of that
chapter/track. Each additional press skips
back one chapter/track.
Pressing
SKIP
| or | during play started
from menu on Video CDs may recall menu.
Still Picture or Pause
Press
PAUSE/STILL
during play.
Press
PLAY
to release.
DVD/Video CD : DECK will enter still picture mode.
CD : DECK will enter pause mode.
Frame by Frame Picture
(DVD/Video CD)
Press
PAUSE/STILL
in still mode.
Press
PLAY
to release.
Each press advances picture one frame.
Hold button down for consecutive frame advance.
Whether pictures are advanced by FRAME or
FIELD is selected automatically. (See p. 57.)
Slow Motion Picture
(DVD/Video CD)
Press
FF/SLOW+
or
REW/SLOW-
in still mode.
Press
PLAY
to release.
Slow motion speed, slow at first, is increased
with each additional press of the button up to
5 levels.
Reverse slow motion is not available for Video CDs.
When appears on the screen while a button
is being operated, it means that the
corresponding operation is prohibited by DECK
or the disc.
*Important: If a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
Reverse Skip Forward Skip
Current playback position
Chapter/Track Chapter/Track Chapter/
T
rackChapter/
T
rack
Power turns off after DECK has been in
Stop mode (DVD) for about 5 minutes.
Auto-Power Off Function
Basic
Operation
Please read the disc jacket for operation
information.
If a single sided disc is placed in upside
down, THIS TYPE OF DISC CANNOT BE
PLAYED. PLEASE INSERT A DIFFERENT
DISC is displayed.
Remove disc and press DECK POWER off
when not in use.
Disc continues to rotate with menu displayed
even after play is done.
Press STOP to clear menu display when
finished with menu.
DECK memorizes the point where STOP is
pressed (STOP is displayed on screen).
Press
PLAY
to resume play from this point.
Pressing
STOP
again or opening the tray
cancels RESUME, however, RESUME is not
canceled when power is turned off and on.
RESUME works only with discs for which
elapsed play time is displayed during play.
Resume Function
Notes
1. Do steps 1-4 (previous page).
When menu appears, press
STOP
.
2. Press
NUMBER keys
to select desired
track (play begins).
Check disc for track numbers.
Press 1 to start at beginning of disc.
To Resume Menu use,
Press
STOP
and press
PLAY
, then the
menu will be displayed.
Now, go to step 5 (previous page).
Enjoy Video CDs featuring
playback control without using
menus (Video CDs only)
V.S.S. (Virtual Surround Sound)
Press
VSS
in DVD mode.
The Surround sound effects can be
changed by pressing VSS repeatedly as
shown by the figure below.
Surround sound effects is available in DVD
mode only.
Turn off the surround effects on the other
equipment.
V.S.S. will not work, or will have less effect,
with some discs.
Turn V.S.S. off if it causes distortion.
Sound will only come from the two front
speakers if V.S.S. is on.
Enjoy a surround-like effect if you are
using two front speakers only. The effect
is broadened and sound seems to come
from virtual speakers on either side if the
disc has surround signals recorded on it.
Note
VSS OFF
VSS OFF (default)
VSS1
VSS3
VSS2
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4723
24
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Recording
Press PROG*
to display Program.
Press PROG
to end programming.
3
1
DAILY
13
1
31
12
SELECT /
Selection Order
WEEKLY
(SAT)
WEEKLY
(MON)
WEEKLY
(SUN)
14
Example
Today
2) To set remaining items,
press
to select and
press SET
to set START/ STOP times,
CH (channel) or LINE
input (p. 35), and tape
speed (SP, LP, SLP).
To Enter More Programs,
press
to select and
press SET
to set an unused program
number, and then repeat
step 2.
Or
Press PROG
to exit.
1) To set record DATE,
press
to select:
1~31= one time, or
DAILY= MON~ FRI, or
WEEKLY= same time
each week and
press SET.
See selection order left.
SE
SE
L
E
C
T
START
D
AT
E
13
SUN
SUN
--:--
--:--
--
T
OD
A
Y
DATE START ST
O
P
C
H
SLP
SELE
C
T
:
SET
:
SET
END
:
P
R
O
G
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
DT
STA
R
T
ST
O
P
CH
SPD
13 10
:
00
P
12
:
00
P
0
2
SP
--
--
:
--
--
:
--
--
--
--
--
:
--
--
:
--
--
--
--
--
:
--
--
:
--
--
--
C
AN
C
EL
:
A
DD
/
DLT
SELECT 1-8
:
E
NTER
: SET
EXIT
:
P
R
O
G
Ready Checklist
All connections are made. (pp. 12 ~ 15)
TV and DECK are plugged in.
Clock set correctly. (p. 18)
Tape has rec.tab. (p. 6)
Remote is in VCR mode. (Press VCR.)
Sufficient tape remaining for recording time.
The Timer Indicator lights up on DECK.
You can do Timer Recording with the power on or off.
•“TIMER REC WILL START SOON appears on-screen for 2 minutes
before Timer Recording starts. If DECK is in DVD mode, no message
appears, but the VCR REC Indicator, the VCR mode indicator and
REC will flash on Multi function Display.
VCR REC Indicator
VCR mode Indicator
<Multi Function Display>
TIMER Indicator
2
ADD/DLT
POWER
SET
PROG
SELECT
VCR
TIMER REC
Hi
Hi
-
Fi
Fi
VCR
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4724
25
To Replace program...
To Clear program...
Review, Replace or Clear Program Contents:
(Recording is not in progress)
or
Important notes when using DSS Receiver
When recording programs via DSS Receiver, DSS Receiver must be left on.
When recording programs via an antenna or cable, DSS Receiver must be turned off.
C
AN
C
EL
:
A
DD
/
DLT
SELECT
1-8 :
ENTER : SET
EXIT
: PROG
DT
STA
R
T
ST
O
P
CH
SPD
7 9
:
00
A
12
:
00
A
08
SP
8
10
:
00
P
12
:
00
P
02
SP
10
8
:
00
P
9
:
00
P
10
SP
S
U
9
:
00
P
10
:
00
P
L1
LP
C
AN
C
EL
:
A
DD
/
DLT
SELECT
1-8 :
ENTER : SET
EXIT
: PROG
DT
STA
R
T
ST
O
P
CH
SPD
--
--
:
--
--
:
--
--
--
8
10
:
00
P
12
:
00
P
02
SP
10
8
:
00
P
9
:
00
P
10
SP
S
U
9
:
00
P
10
:
00
P
L1
LP
Press ADD/DLT.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
1
2
3
Press
to select number and
press SET
to display.
To cancel a Timer
Recording in progress...
Repeat Step 2 (p. 24)
to set new programs.
Press PROG
to end the programming.
Hold down STOP in VCR mode for
a few seconds to cancel the Timer
Recording.
(The TIMER Indicator goes out
on Multi Function Display.)
Any future daily or weekly recording
will be performed as programmed.
7
SUN
9
:
00A
12
:
00A
08
T
OD
A
Y
----------------------------------------
DATE
S
TART
S
TOP
CH
SP
SE
L
E
C
T
START
D
AT
E
SELE
C
T
:
SET
:
SET
BACK :
END
:
P
R
O
G
Notes
If you are using a Cable Box, the VCRs channel for Timer Recording must be set to
the Cable Box input channel and Cable Box must be manually set to the desired
channel. Cable Box power must be left on.
2 minutes before Timer Recording is performed, PLEASE PREPARE FOR TIMER
REC appears and Timer Indicator flashes.
Be sure a cassette with record tab is loaded and DECK is in Stop mode.
If a power interruption occurs while programming the timer, the timer program(s) may be
canceled. If TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION
appears on-screen, please re-enter the timer programs.
If the start time for Timer Recording comes up during recording and playing back,
Timer Recording will not be performed.
Press PROG
to display Program List.
4
VCR
Operation
D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4725
26
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
MONO broadcast
Normal monaural sound broadcast.
SAP broadcast
Secondary Audio Program (sub
language) broadcast. Select SAP
audio mode for the sub language.
MTS Stereo broadcast
Multi-channel Television Sound
Stereo broadcast. Select STEREO
audio mode.
If stereo broadcast is weak and
display flickers, select MONO audio
mode for possible better results.
MTS Stereo and SAP broadcast
Multi-channel Television Sound
Stereo (main language) and
Secondary Audio Program (sub
language) broadcasts are being
received simultaneously.
Select STEREO or SAP audio mode.
The following are possible audio broadcast types and on-
screen displays.
The signal being received is indicated with an
mark
while the selected audio mode is indicated with an arrow.
Receivable Broadcast Types
MTS Broadcast/ VHS Hi-Fi Stereo System
Equipped with
®
-TV
Noise Reduction for
true MTS reproduction.
®
-TV Noise
Reduction is required
for good stereo
separation and audio
fidelity.
®
is a
registered trademark,
and is licensed by
®
Technology Licensing.
Connection
Make the Audio/Video Connection as shown on pp. 12 ~ 15.
You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.
To display the broadcast signal being received,
press DISPLAY*.
ST
OP
1
2
:
0
0
A
M
CH
02
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
CH
02
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
CH
02
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
CH
02
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
AUDIO
(SAP/Hi-Fi)
DISPLAY
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4726
27
Audio Mode for Recording
1
2
Make a recording.
See page 21.
3
Audio Mode for Playback
Start playback.
See page 20.
Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard
stereo tapes will playback in monaural sound.
To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to
a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)
If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
Hi-Fi and normal audio playback volume level may differ.
Arrow indicates
selection.
Refer to Receivable Broadcast Types on page 26.
Arrow indicates selection.
Select HIFI (L/R) or HIFI (L) or HIFI (R) to listen to stereo
recordings in stereo sound.
Select NORMAL for monaural sound.
Display disappears after 5 seconds.
Press AUDIO (SAP/Hi-Fi)
to display audio mode.
(Display disappears after 5 seconds.)
Press AUDIO (SAP/Hi-Fi) repeatedly
to select desired mode.
Press AUDIO (SAP/Hi-Fi)
to display audio mode.
Press AUDIO (SAP/Hi-Fi) repeatedly
to select desired mode.
STER
EO
SAP
M
ONO
Notes
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
1
2
3
H
I
F
I
: L
/
R
H
I
F
I
: L
H
I
F
I
:
R
N
ORM
AL
VCR
Operation
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4727
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Multi-Brand Control Feature
DSS/
CABLE
POWER
ENTER
NUMBER
keys
TV
VCR
DVD
The Remote Control can be set to control some TV and
Cable Box/DSS functions.
Find your TV and Cable Box/DSS Receiver
Brand Code Number on the following page.
Set up for TV control,
hold down TV button,
enter code with NUMBER keys.
Multi-Brand Control Setup
Confirm code entry,
press POWER to turn selected unit on or off.
See table below for controllable functions in each mode.
Set up for Cable or DSS control,
hold down DSS/CABLE button,
enter code with NUMBER keys.
If code number is 100 or greater,
e.g., press 1 - 0 - 2 for 102.
3
1
Repeat setup after remote battery replacement.
Remote will not control every TV, Cable Box, or
DSS made by the manufacturer listed. If you get
no response, your particular unit cannot be
controlled. There are NO additional codes for the
products listed. If your product is not listed, then
the remote is not compatible with that product.
Notes
2
Mode
Unit
DVD/VCR TV
DVD/VCR
TV
All
POWER, INPUT,
NUMBER keys,
ENTER,
CH / ,
VOL
+
/
-
EJECT/
OPEN/CLOSE
*,
DISPLAY
,
PLAY
,
STOP
,
FF/SLOW+
,
REW/SLOW-
,
VCR/TV, PAUSE
/STILL
,
SKIP
,
AUDIO
, CM/ZERO,
TAPE POSITION,
COUNTER RESET, SPEED,
REC,
PAGE
After remote is set up, you can select VCR, DVD, TV, or
DSS/CABLE for the desired function.
Press VCR,
DVD
, TV, or DSS/CABLE on the remote.
(Table below shows available remote buttons for each mode.)
CABLE/ DSS
Using Multi-Brand Control
CABLE/
DSS
POWER, ENTER,
NUMBER keys
(except 100key),
CH /
Not all functions listed may be controllable.
In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing
NUMBER keys for channel selection.
Notes
VOL
+
/
-
VOL +/-
* Bold: VCR Function
Bold Italic: VCR and DVD Functions
Italic: DVD Function
Normal: TV, Cable Box or DSS Receiver
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4728
29
Some manufacturers use several codes for one brand. If the first code entered fails, try the
next one listed.
Some TV, Cable Box and DSS Receiver brands require you to turn on the power manually.
Cable Box Brand Code Numbers
Panasonic ....................... 01, 02
Quasar ............................ 01, 02
RCA ....................................... 03
GE ......................................... 03
Zenith .................................... 04
Magnavox.............................. 05
TV Brand Code Numbers
Sylvania ................................ 05
Sharp ............................... 06, 07
Sony ...................................... 08
Toshiba ................................. 09
Sanyo .................................... 10
Fisher .................................... 10
JVC........................................ 11
Hitachi ................................... 12
Mitsubishi ........................ 07, 13
Samsung ............................... 14
Gold Star...................15, 16, 17
DSS Brand Code Numbers
Important Notes
Archer ......................... 44, 06, 01, 120, 05, 63, 126
Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30
52, 04, 124, 126
Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126
Curtis ..................................... 08, 09, 25, 61, 53, 87
Century ...................................... 44, 51, 75, 59, 126
Cabletenna .................. 29, 09, 01, 63, 120, 44, 126
Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126
Diamond ...................... 29, 09, 01, 63, 120, 44, 126
Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107
Eastern ................................................... 28, 29, 130
Explorer.................................. 08, 09, 25, 61, 53, 87
Gemini .....................................................30, 04, 124
General Electric ......................................01, 57, 120
General Instruments . 01, 84, 83, 34, 03, 02, 04, 55
65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Gerrard............................................... 44, 51, 75, 59
GC Electronics ............... 44, 42, 63, 29, 30, 52, 04
124, 126
Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130
Hitachi ................................................................... 31
Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66
67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco ...................................................... 30, 04, 124
Macom ................................................................... 31
Magnavox...................................................... 26, 112
Matsushita ................................. 17, 16, 08, 87, 109
Movietime ...................... 32, 39, 42, 44, 126, 38, 40
Maestro ........................................................... 74, 35
NEC .................................................... 40, 19, 38, 32
NSC .................................................... 40, 19, 38, 32
Novavision ............................. 08, 09, 25, 61, 53, 87
Next Level...........01, 84, 83, 34, 03, 02, 04, 55, 65
66, 67, 68, 120, 106, 121, 122
Oak................................................. 46, 11, 129, 101
Oak Sigma ..................................... 46, 11, 129, 101
Panasonic .................................. 17, 16, 08, 87, 109
Philips ................... 23, 24, 20, 13, 07, 50, 128, 129
Pioneer...................................................... 06, 05, 12
Pulsar.................... 04, 42, 63, 44, 30, 52, 124, 126
Quest ........................................................ 06, 05, 12
Radio Shack ............................... 44, 51, 75, 59, 126
RCA ............................................ 17, 16, 08, 87, 109
Realistic ..................................... 44, 51, 75, 59, 126
Recoton...................................... 44, 51, 75, 59, 126
Regal ................. 41, 14, 15, 28, 102, 104, 103, 130
Regency ..................................................28, 29, 130
Rembrandt ....... 44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung ...................................... 42, 06, 32, 05, 40
Scientific Atlanta ................... 08, 09, 25, 61, 53, 87
Sheritech............................................................... 27
Signal ............................................................ 26, 112
SL Marx............. 42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer ...................................... 17, 16, 08, 87, 109
Standard Components ............... 32, 39, 42, 44, 126
Stargate ..............04, 42, 32, 40, 63, 44, 30, 52, 06
124, 126
Sylvania .......................................................... 19, 18
Teknika ........................................................... 74, 35
Telecaption.................................................... 77, 127
Teleview ................................. 40, 19, 38, 32, 42, 06
Texscan .......................................................... 19, 18
Tocom ...................................34, 33, 01, 42, 66, 120
Toshiba ................................................................. 36
Unika ........................... 44, 42, 63, 29, 01, 126, 120
Universal ..............................52, 43, 44, 63, 42, 126
Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107
Videoway.......................................... 07, 23, 50, 129
Vidtek.................................................................... 64
Zenith ............................................... 07, 23, 50, 129
Toshiba....................................................... 90
Hitachi/ Hughes.................................... 91, 99
Primestar .................................................... 92
Drake .......................................................... 93
Magnavox............................................. 94, 95
Uniden................................................... 94, 95
Optimus ................................................94, 95
Panasonic................................................... 96
ProScan...................................................... 97
RCA............................................................. 97
SONY.................................................. 98, 105
VCR
Operation
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4729
30
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Index Search
Note
If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
1
2
Tape Operation
Search System
For each recording, an invisible index mark is placed on the tape. A program index and
information are also included for timer recordings. These marks are used to access or
scan recordings.
1
Program End Search
2
Fig. 1
Fig. 2
Fig. 3
Note
Locates end point of recording for continuity.
Examples of Program End Search.
If search exceeds
a few seconds in
BLANK area.
search continues 7 sec. past end point,
tape rewinds to 10 sec. before end point,
tape plays to end point and stops.
Upon locating end point,
If Program End Search is started very close to
an index mark, that mark may be skipped over.
PROGRAM END SEARCH
SEARCH START : FF
EXIT
:SEARCH
Program 2 or BLANK
Program 1
the current tape position
Press SEARCH button
FF
INDEX
End Point
Program 2
Program 1
the current tape position
Press SEARCH button
INDEX
INDEX
BLANK
BLANK
FF
End Point
Program 2
Program 1
the current tape position
Press SEARCH button
BLANK
INDEX
FF
End Point
INDEX SEARCH
ENTER INDEX NUMBER :1
USING
1
-
9 KEYS
FORWARD SEARCH :FF
REVERSE
SEARCH :REW
NEXT :SEARCH
EXIT
:STOP
INDEX SEARCH
FORWARD SEARCH : FF
REVERSE
SEARCH : REW
Press SEARCH*
to display SEARCH
in Stop or Play
mode, and then
press NUMBER
keys
to select recording
number.
To calculate
number, see below.
Press FF/SLOW+
or REW/SLOW- on
the remote to start
search.
Press SEARCH twice
to display SEARCH in Stop or Play
mode.
Press FF/SLOW+
on the remote to
start PROGRAM
END SEARCH.
To cancel, press
PLAY or STOP.
Play begins at
search end.
To search forward
or back 1 index,
press FF/SLOW+ or
REW/SLOW- on the
remote while
screen left is
displayed (10 sec.).
To cancel, press
PLAY or STOP.
To Calculate Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
NOTE: indicates start points of each recording.
61572 34
17534 62
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4730
31
Auto Play
Insert a tape Power comes on,
Play starts if there is no record tab
(see p. 6).
Auto Rewind
Play
Fast Forward
Play Auto Eject
(Repeat Play must be off)
Play
Tape end
Rewind
Tape ejects if set some programs
Auto Operation Functions
Commercial Skip
VCR fast forwards (skips) over 1~3 minutes
of recorded tape.
1
Press CM/ZERO in Play mode.
PLAY
1st Press
2nd Press
3rd Press
1 min Skip
2 min Skip
3 min Skip
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
No indication appears on-screen.
The skip time can be changed by
pressing CM/ZERO repeatedly as
shown by the figure below.
Tape end Rewind
REW/SLOW-
FF/SLOW+
PLAY
SEARCH
NUMBER
keys
CM/ZERO
STOP
VCR
Operation
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4731
32
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Tape Operation (continued)
Repeat Play
Set to playback a recording over and over.
Zero Search
To quickly return to a specified tape location.
Continue to record, playback etc.
Press STOP.
DECK will go into FF or REW mode and stop
at the last point the Counter was set to 0:00:00.
5
4
3
2
1
3
2
1
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
PLAY
1
2
:
0
0
A
M
0
:
0
0
:
0
0
SP
Press ACTION*
to display MENU.
Press
to select SET UP VCR, and
press SET.
Play repeats at tape end or if unrecorded portion
over 30 sec. is detected.
Press ACTION twice
to return to normal screen.
Press DISPLAY during play
to display Counter.
Press COUNTER RESET
at desired position to reset
to 0:00:00.
Press CM/ZERO
in Stop mode
to start Zero Search.
4
Press
to select REPEAT PLAY,
and press SET
to set ON or OFF.
REPEAT
REPEAT
PLAY
:
O
FF
RE
M
OTE
W
ARN
I
NG
:
O
N
AUT
O
SHU
T
-
OFF
:
O
FF
AUT
O
VCR/TV
:
O
FF
SELE
C
T
:
SET
:
SET
END
:
ACT
I
O
N
SET
UP V
CR
Note
For repeat play in DVD mode, see page 48.
REW
1
2
:
3
0
A
M
CH
02
0
:
30
:
30
SP
STOP
1
2
:
3
1
A
M
CH
02
0
:
0
0
:
0
0
SP
VCR/TV Selector FeatureVCR/TV Selector Feature
The VCR/TV selection can be set to
auto or manual.
3
1
REPEAT
PLAY
:
O
FF
RE
M
OTE
W
ARN
I
NG
:
O
N
AUT
O
SHU
T
-
OFF
:
O
FF
AUT
O
VCR/TV
:
O
FF
SELE
C
T
:
SET
:
SET
END
:
ACT
I
O
N
SET
UP V
CR
Press ACTION
to display MENU.
Press
to select
AUTO VCR/
TV, and
press SET
to set ON
or OFF.
Press ACTION
to return to normal screen.
4
Note
OFF(Manual):You select VCR or
TV mode using the
VCR/TV button on the
remote.
ON(Auto): VCR mode is
automatically set when
VCR is turned on, or in
Play mode.
For more on VCR/TV selection, see
Record one station, watch another
and Select channels at DECK
sections (see p. 21).
2
Press
to select
SET UP
VCR, and
press SET.
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4732
33
Weak Signal Display Feature
When ON, picture is displayed regardless of signal
strength.
ON: Picture is displayed regardless of signal
condition, and may not always be clearly visible.
OFF: Screen turns solid blue when signal is weak or
non-existent.
Selecting ON has no effect on connected equipment
with blue back feature.
Press ACTION twice
to return to normal screen.
4
3
2
Press
to select SET UP
CHANNEL, and
press SET.
Press
to select WEAK SIGNAL
DISPLAY, and
press SET
to set ON or OFF.
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
1
Press ACTION
to display MENU.
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
ANT
ENN
A
:
C
ABLE
A
U
T
O
S
E
T
W
EA
K
S
I
GN
AL
D
I
SPLA
Y:
OFF
SET UP
CH
A
NNE
L
Special VCR Features
*Important: If a remote control button does not work
when pressed, press the VCR button
on the remote and try the button again.
When set to ON, all operations
except for timer record and tape
eject are prohibited. Useful for
households with small children.
VCR Lock Feature
V
CR
L
OC
K ACT
I
VA
TED
V
CR
L
OC
K
O
FF
VCR Lock cancels in 24 hours if
clock is set.
To turn off, repeat above.
To turn on, hold down REC on
DECK in Stop mode with no
tape inserted for 7 seconds.
(Please ignore NO CASSETTE
warning.)
REC
Auto Shut-Off Feature
The power shuts off at a preset time.
3
1
4
Press
to select AUTO SHUT-OFF.
Press SET repeatedly to
change shutoff time as
shown below.
Press ACTION twice
to return to normal screen.
Press ACTION
to display MENU.
2
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
Press
to select SET UP VCR, and
press SET.
REPEAT
PLAY
:
O
FF
RE
M
OTE
W
ARN
I
NG
:
O
N
AUT
O
SHU
T
-
OFF
:
O
FF
AUT
O
VCR/TV
:
O
FF
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
SET
UP V
CR
OFF
2 Hours
6 Hours
4 Hours
The shut-off countdown will not function during Play or
Record.
Note
COUNTER
RESET
DISPLAY
ACTION
SET
CM/ZERO
STOP
SELECT
VCR
Operation
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4733
34
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Special VCR Features (continued)
If Multi-brand feature is used (p. 28), and this feature is
set to on, a warning appears whenever an invalid key
is pressed in TV, DSS or CABLE mode.
4
3
1
If OFF, remote warning will not appear
when invalid key is pressed.
Press ACTION*
to display MENU.
Press
to select
REMOTE WARNING, and
press SET
to set ON or OFF.
Press ACTION twice
to return to normal screen.
Remote Warning Feature
2
Press
to select SET UP VCR,
and
press SET.
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
REPEAT
PLAY
:
O
FF
RE
M
OTE
W
ARN
I
NG
:
O
N
AUT
O
SHU
T
-
OFF
:
O
FF
AUT
O
VCR/TV
:
O
FF
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
SET
UP V
CR
*Important: If a remote control button does not work
when pressed, press the VCR button
on the remote and try the button again.
To find out the present tape position and amount of tape remaining.
Tape position is displayed for VHS-C type Cassettes, tapes
under 30 minute long, and some other tapes, but the
position is not correct.
Tape remaining time display may not be
precise.
1
BE
G
I
N
END
SP
R 120 M
I
N.
•“DETECTING TAPE POSITION is displayed
only when a cassette is first inserted, and it
takes several seconds for correct tape
position to appear.
Tape Position and Tape Status Feature
Press TAPE POSITION
to return to normal screen.
2
The present tape position indication and
amount of tape remaining (according to
tape speed) is displayed.
DETECTING TAPE POSITION
Press TAPE POSITION
to detect current tape position.
This function cannot display exact amount of tape remaining for
tapes 30 minutes or less, or for tapes over 120 minutes in length.
Note
INPUT
ACTION
SET
TAPE
POSITION
SELECT
STOP
REC
PAUSE/
STILL
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4734
35
Copying Your Tapes (Dubbing)
1
Insert a pre-recorded tape.
2
Insert a blank tape with record tab.
Press REC, then PAUSE/STILL
immediately to enter REC/PAUSE
mode.
3
Press INPUT to set DECK Input mode to
LINE for Video Input.
(See Selecting the Input Mode below.)
4
Press PLAY to start dubbing.
Playing VCR starts playback.
Press PAUSE/STILL to start dubbing.
DECK starts recording.
Press STOP to stop dubbing.
Caution: Unauthorized exchanging and/or copying of copyrighted recordings may be
copyright infringement.
Please note that some tapes cannot be dubbed on DECK. Also, it is not
possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.
Playing (Source) VCR Recording (Editing) DECK
5
To Monitor Dubbing on TV
1 Turn TV on and tune to the Recording
VCR channel (CH 3 or CH 4).
2 If Auto VCR/TV (see p. 32) is set to
OFF, press VCR/TV on the remote to
be VCR mode.
Note
Dubbing tapes protected with Copy
Guard will result in poor quality
recordings.
Connection
Press STOP to stop dubbing.
Press PLAY, then PAUSE/STILL
immediately to enter PLAY/PAUSE
mode.
The operation of steps 4 and 5 must be done on the
playing and recording VCRs at the same time.
Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.
To monitor the dubbing, also connect TV as shown.
Connect L and R AUDIO OUT terminals on Playing VCR to L and R
AUDIO IN terminals on DECK.
In place of Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the units Audio/Video outputs to DECK.
Selecting the Input Mode
Method 1: Press INPUT repeatedly.
Channel Number
LINE1
LINE2
Method 2: Press CH / .
Display will change as below.
Front of DECK
VIDEO IN 2
L-AUDIO IN2-R
(Audio/Video In Terminals
on the front of DECK are
available)
IN
FROM
ANT.
OUT
TO
TV
IN 1
VHF/UHF
OUT
TV
OUT
VHF/
UHF
DVD/VCR DECK
VIDEO
AUDIO
1
L
R
VCR/ Camcorder (Hi-Fi)
VIDEO
AUDIO
L
R
•“L1 or L2 lights up on Multi Function Display
(about 4 seconds) when LINE1 or LINE2 is selected.
LINE1: For rear audio/video connection.
LINE2: For front audio/video connection.
1
2
1
2
3
125
LINE1
(CABLE)
69
(TV)
or
LINE2
Press
Press
VCR
Operation
D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4735
36
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
AUDIO: 3 ESP
3 ESP
Dolby Digital 3/2.1ch
Hola
SELECT
SELECT
:
END
END
:AUDIO
AUDIO
AUDIO: 1 ENG
Dolby Digital 3/2.1ch
Hello
SELECT
:
END
:AUDIO
Te amo
You can select a different subtitle language (if offered) than
the one set at the Settings for DVD Operation.
(See p. 53.)
Press
to select a language.
Press
to select ON or OFF.
Subtitle Language (DVD only)
Display disappears after
5 seconds.
When no subtitles are offered,
- will be displayed instead of
the language number.
Press
SUB TITLE
*
in Play mode to display
the subtitle selection
on-screen.
Ready Checklist
Please read Basic DVD Operation
on page 22.
You can change the audio soundtrack language, selected
at the Settings for DVD Operation, to a different language
if available. (See p. 53.)
(This operation works only with discs on which multiple
audio soundtrack languages are recorded.)
Press
AUDIO
in Play mode to display the
audio selection on-screen.
Audio Soundtrack Language (DVD only)
Disc Operation
1
2
1
2
Subtitle language being played back (see chart, right).
Press
to select desired language.
Audio soundtrack language being played back (see chart,
above right).
Display disappears after
5 seconds.
Audio attribute 1 type, sampling
frequency, bit No. of the disc or
number of speaker channel.
If after several presses of the button the language does not
change, language selection is not offered on the disc.
When disc is removed, subtitles revert to initial setting
language. If the initial language is not recorded on the disc,
the discs priority language will appear.
With DVD-RAM, the subtitle can only be set to ON/OFF.
The subtitle language cannot be selected.
Notes
[Subtitle language]
[Audio sound track language]
Change the No. by pressing ,
and press
SET
.
[Audio attribute 1 type, sampling
frequency, bit No. of the disc (see p. 54.)]
LPCM
Dolby Digital
DTS
44.1 kHz
192 kHz
1 ch - 5.1 ch
1 ch - 5.1 ch
16 bit
20 bit
24 bit
Linear PCM disc
Dolby Digital disc
DTS disc
~
If, after several presses of the AUDIO
button the language does not change,
language selection is not offered on the
disc.
When disc is removed, language
reverts to initial setting. If this language
is not recorded on the disc, the
language recorded will be heard.
With DVD-RAM, Audio Soundtrack
Language cannot be set. Audio stream
and Audio mode (LR/L/R) setting can
be made. Audio stream operation
method is the same as Audio
Soundtrack Language. Press to
move the cursor to Audio mode, then
press to select LR/ L/ R.
Notes
ENG
FRA
DEU
ITA
ESP
NLD
English
French
German
Italian
Spanish
Dutch
SVE
NOR
DAN
POR
RUS
JPN
Swedish
Norwegian
Danish
Portuguese
Russian
Japanese
CHI
KOR
MAL
VIE
THA
Chinese
Korean
Malay
Vietnamese
Thai
Other
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4736
37
SELECT :
When appears on the screen while
a button is being operated, it means
that the corresponding operation is
prohibited by DECK or the disc.
The ANGLE Indicator lights up on
DECK when a scene recorded at
different angles is detected.
The angle number can be set
beforehand so that the angle is
switched whenever the ANGLE
Indicator lights up.
ANGLE Indicator
1
Press
AUDIO
in Play mode
to display the audio screen.
Vocal Selection for Karaoke Discs
(DVD/Video CD)
DVDs may contain scenes shot from multiple camera
angles allowing the same scene to be viewed at different
angles. You can view these angles, if available, using the
ANGLE button.
1
Press
ANGLE
in Play mode to display the
angle selection on-screen.
Display disappears after
5 seconds.
Multiple Angle Viewing (DVD only)
2
Press
to select the desired
angle.
2
Press (or )
to select as shown below,
and
press
(or ) to set.
(DVD only)
Number of angle being played back.
You can enlarge specific portions of a picture and
select the zoom ratio using the ZOOM button during
DVD playback.
Press
ZOOM
repeatedly to change display
as follows.
Picture Zoom (DVD-Video/DVD-RAM only)
You can enlarge the center portion of the image
to one of 2 magnifications.
The subtitle cannot be enlarged nor
can its position be changed.
The picture zoom feature does not
work with a Video CD.
During picture zoom, ZOOM1 or
ZOOM2 appears on-screen for 5
seconds.
Zooming, on some discs, may result
in poor picture quality, or may not
operate at all.
Use the , , and buttons to move the position
up, down, left and right.
Notes
Notes
*
Important: if a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
AUDIO
SET
ANGLE
SUB TITLE
ZOOM
SELECT
DVD
Operation
SELECT :
DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF
DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF
Video CD LR L R
SELECT :
END :AUDIO
This function not available with DVD-RAM.
Note
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4737
38
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Some DVDs have more than one title, e.g. movies.
If the disc offers a title menu, you can select the desired
title number. (Operation may vary according to the disc.)
1
Press
TITLE
*
in Play mode
to display the title screen.
Title Menu (DVD only)
DVDs may offer a special menu. This menu may include
guides to unique contents, audio/subtitle languages, etc.
Although contents and operation may vary, the following
steps show basic steps for using the menu.
1
2
Press
MENU
in Play mode to display
DVD MENU.
Press or
NUMBER keys
to select an item, and
press
SET
or
PLAY
to perform.
DVD Menu (DVD only)
2
Press or
NUMBER keys
to select a title, and
press
SET
or
PLAY
to start playing.
Disc Operation (continued)
•“Pressing
SET
or
PLAY
is
not necessary when using
NUMBER keys.
<Example>
<Example>
<Example>
T I TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
T
I
TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
DVD MENU
3 . ANGLE
1 . SUBT
I
TLE
2 . AUD
I
O
DVD MENU
3 . ANGLE
1 . SUBT
I
TLE
2 . AUD
I
O
B
i
rds
of the world
<Example>
Repeat step 2 if there is
more than one menu.
•“Pressing
SET
or
PLAY
is
not necessary when using
NUMBER keys.
MENU
SET
STOP
PLAY
NUMBER
keys
TITLE
CLEAR
ACTION
SELECT
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4738
39
You can program specific tracks and order of play.
Program Play (Video CD/CD only)
Ready Checklist
DECK is in DVD mode, press DVD.
Video CD or CD is inserted.
1
Press
ACTION
to display DVD MAIN MENU.
2
Press
to select
PLAY MODE, and
press
SET
to display.
3
Press
to select
PROGRAM PLAY,
and
press
SET
to display.
5
Press
to select START, and
press
SET
to start play
of programs in the
sequence selected.
To cancel, press
STOP
during play, then press
CLEAR
.
4
Press
to select a track
number (Track
numbers on disc are
displayed.), and
press
SET
.
Repeat step 4 to select another track.
The selected track is added on the right side.
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
STI LL MODE : AUTO
TV MODE : 4:3 Letterbox
PARENTAL
LOCK
:
LEVEL 8
PLAY MODE
PLAY MODE
PLAY MODE
SELECT :
SET : SET
END : ACTION
PROGRAM PLAY
PROGRAM PLAY
RANDOM PLAY
SELECT :
SET : SET
END : ACTION
DISC PROGRAM
1 61116 5 8
2 7 12 17 15 6
3 8 13 18 1 13
4 91419 3 2
5101520 2
CLEAR LAST
CLEAR ALL START
PROGRAM PLAY
PROGRAM PLAY
SELECT :
SET : SET
END : ACTION
DISC PROGRAM
1 61116 5 8
2 7 12 17 15 6
3 8 13 18 1 13
4 9 14 19 3 2
5101520 2
CLEAR LAST
CLEAR ALL START
Notes
Program Repeat Play
(Video CD/CD only)
4
Press
SET
to enter Select mode.
Cursor move to OFF.
5
Press to select DISC.
(DECK Information Screen)
(DECK Information Screen)
1
Do operation steps 1 through 5
at left on this page.
2
Press
DISPLAY
to display Disc
Information screen.
(Disc Information Screen)
3
Press
DISPLAY
to display
DECK Information screen.
6
Press
SET
to set mode.
Cursor move to REPEAT.
To cancel, select REPEAT :
OFF in step 5, then press
SET
.
SELECT:
SET : SET END : DISPLAY
PLAY
REPEAT : DISC
PROGRAM PLAY
SET : SET END :DISPLAY
SET : SET NEXT:DISPLAY
TRACK : 1 VIDEO CD
PBC : OFF 01:35 :12
*
Important: if a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
Up to 15 tracks can be programmed.
•“ or (depending on disc) indicates additional
PROGRAM PLAY screen.
Press for next or previous screen.
To clear the last program one by one
Press to move to CLEAR LAST and
press
SET
. (Pressing
CLEAR
on remote control
also clears last program.)
To clear all programs
Press to move to CLEAR ALL and press
SET.
(Programs are also cleared when the power
is turned off or the disc is removed.)
DVD
Operation
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4739
40
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Tracks are played in a random order.
Random Play (Video CD/CD only)
Press
ACTION
*
to display DVD MAIN MENU.
1
Disc Operation (continued)
Press
to select PLAY MODE,
and
press
SET
to display.
2
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
STI LL MODE : AUTO
TV MODE : 4 :3 L et t er b ox
PARENTAL
LOCK
:
LEVEL 8
PLAY MODE
Press
to select
RANDOM PLAY, and
press
SET
to begin random play.
To cancel, press
STOP
during play, then press
CLEAR
.
3
PLAY MODE
SELECT :
SET : SET
END : ACTION
PROGRAM PLAY
RANDOM PLAY
Ready Checklist
DECK is in DVD mode, press DVD.
Notes
SELECT
STOP
CLEAR
ACTION
SET
VOLUME
ADJUST
DISPLAY
NUMBER
keys
PAGE
•“ON is set ..... When a DVD is played back, the average volume is increased.
•“OFF is set.... The volume level recorded on the disc is played back just as it is.
Setting the VOLUME ADJUST
Press
VOL.ADJ
repeatedly to change ON
OFF.
•“ON or OFF lights up on Multi Function Display (about 3 seconds) when
press VOL.ADJ.
Some DVD
[Volume level is low]
VOLUME ADJUST OFF
Volume is the original level.
VOLUME ADJUST ON
Volume level is increased
when played back.
Some DVDs are recorded in lower than average volume levels.
For these DVDs, this DECK can be set so that the average volume
is increased.
This feature is available only for Dolby Digital sound tracks.
When audio equipment is connected, setting the Sound Output level to OFF is recommended.
If the sound becomes abnormal while playing a disc, set the Sound Output level to OFF.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4740
41
*
Important: if a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
DVD
Operation
DVD-Audio Operation
Bonus Group playback
1
Some DVD-Audio discs contain Bonus Group tracks which can be played by entering a
4-digit secret code.
Press
DISPLAY
in stop mode to display On-Screen Displays.
Press to select GROUP, and press
SET
.
Press or
NUMBER keys
to select bonus group
number, and press
SET
(see pp. 44, 45.)
2
Press
NUMBER keys
to enter bonus group secret code, and press
SET
.
To Make Corrections
Press
repeatedly to move the cursor.
Press
NUMBER keys
to make the correction.
3
Notes
4
Press
CLEAR
to return to normal screen.
Note
Note
When the proper secret code has been entered, Bonus Group track 1 playback
begins. If a mistake is made, the secret code enter screen is redisplayed.
If the proper secret code is already entered, Bonus Group tracks can be
selected. (Secret code enter screen is skipped.)
This code is specifically for the disc and differs from Parental Lock secret code
(p. 52). Please refer to disc jacket instructions.
During playback, Bonus Group tracks cannot be selected.
SELECT:
SET : SET NEXT : DISPLAY
GROUP : 2 DVD-AUDIO
TRACK : 1 00: 12: 34
BONUS GROUP
ENTER 4
-
D
I
G
I
T
CODE
----
This DECK, equipped with a 192 kHz/ 24 bit Audio D/A converter, supports DVD-Audio
recorded with high quality sound.
The DVD-Audio feature includes Still Image Skip and Bonus Group Playback
functions. (See below.)
Please refer to Basic DVD Operation on pages 22 and 23.
Still Image Skip
DVD-Audio still images (only if contained) can be skipped over.
Press
PAGE
in Play or Pause mode to display the still image and page
number.
PAGE : 1
SELECT :
Each press of PAGE changes page number as shown below.
Pressing PAGE on the last page returns to PAGE 1.
SELECT :
PAGE : 2
Still Image Skip function not available with all discs.
PAGE
:
1 PAGE
:
2 PAGE
:
3 ....... PAGE
:
XX
Press PAGE
Press PAGE
Press PAGE
Press PAGE
Note
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4741
42
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Page 1/4
Direct Navigator
No. Date Length Title
1
2002/12/24
5:15:41AM
00:01:00
Drama
2
2002/12/25
4:31:49AM
00:03:12
Pana NEWS
3
2002/12/25
8:24:25AM
00:15:01
Tigers vs.Giants
4
2002/12/25
12:45:00AM
00:03:00
Dinosaur
SET : SET END:TITLE
SELECT:
DVD-RAM Operation (DVD-RAM only)
1
Do steps 1 ~ 3 on page 22.
This DECK was designed for playback only. DVD-RAM recording is not possible.
You can enjoy playing your personally recorded/edited DVD-RAM discs on this DECK.
Note
2
Press
TITLE*
or
MENU
to display Direct Navigator
or Play List menu for easy title or scene selection.
3
4
Press
STOP
to stop playing.
Press
OPEN/CLOSE
to eject the disc.
1
Press
TITLE
in Play/Stop mode to display the Direct Navigator
menu.
2
Press to select a page and press
to
select a title (Program No.).
Then, press
SET
or
PLAY
to start playing.
If the DVD-RAM features Direct Navigator, a list of recorded titles is displayed. Simply select a title
number and start playback. (Operation can vary with disc used.)
Direct Navigator
•“Pressing SET or PLAY is not necessary when
using NUMBER keys.
Program No.
Titles
Recording
time length
Recording time
and date
Page No.
<Input
Example>
Using NUMBER keys starts playing automatically.
The number of available titles varies with each disc.
1 digit number 1 ••• 1
2 digit number 12 ••• 10 1 2
3 digit number 123 •••100 1 2 3
3
Press
TITLE
to clear Direct navigator menu.
(Press
ACTION
to display DVD MAIN menu.)
Play a DVD-RAM
Play begins from the first program title recorded on
the DVD-RAM.
See below for Direct Navigator or next page for Play
List information.
(Example)
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4742
43
Page 1/5
Play List
No.
Date
Length
Title
1
2002/12/24
5:15:41AM
00:01:00
Movie Picture
Playback
2
2002/12/25
4:31:49AM
00:03:12
Still Picture
Playback
3
2002/12/25
8:24:25AM
00:15:01
Hybrid Playback
SELECT:
SET :SET
END:MENU
2002/12/25
12:45:00AM
00:03:00
Partial Playback
4
1
Press
MENU
in Play/Stop mode to display the Play List menu.
2
Press to select a page and press
to
select a title (Play List No.).
Then, press
SET
or
PLAY
to start playing.
If the DVD-RAM features a Play List, your preselected list of favorite scenes is displayed for easy
access. (Operation can vary according to how you edited the DVD-RAM.)
Play List
•“Pressing SET or PLAY is not necessary when
using NUMBER keys.
TitlesRecording time
and date
Page No.
<Input
Example>
Using NUMBER keys starts playing automatically.
The number of available titles varies with each disc.
1 digit number 1 ••• 1
2 digit number 12 ••• 10 1 2
3 digit number 123 •••100 1 2 3
3
Press
MENU
to clear Play List menu.
(Press
ACTION
to display DVD MAIN menu.)
Play List No.
Established
time length
(Example)
Titles of Direct Navigator and Play List cannot be changed using this DECK.
With Direct Navigator, up to 99 programs can be displayed. With Play List, up to 99 titles (999
scenes) can be displayed.
While DVD MAIN MENU is displayed, Direct Navigator and Play List display will not appear even
if TITLE or MENU is pressed.
When appears on the screen while a button is being operated, it means that the
corresponding operation is prohibited by DECK or the disc.
Notes
10
MENU
SET
STOP
NUMBER
keys
TITLE
PLAY
SELECT
DVD
Operation
*
Important: if a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4743
44
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Notes
When
DISPLAY
button is pressed
during playback of a Video CD with
Playback control,
NUMBER keys
are
not available on the displayed screen.
In this case, press
DISPLAY
again to
remove the displayed screen.
When appears on the screen while
a button is being operated, it means
that the corresponding operation is
prohibited by DECK or the disc.
DVD Operation using On-Screen Displays
Ready Checklist
DECK is in DVD mode, press DVD.
SET
NUMBER
keys
DISPLAY
SELECT
CLEAR
1
Press
DISPLAY*
in Play or Stop mode
to display On-Screen Displays.
When
DISPLAY
is pressed, On-Screen Displays show
disc information (title/chapter/track number, elapsed
playing time) and DECK information (repeat play, play
mode).
Each press of
DISPLAY
changes the on-screen
display as follows. (Refer to pp. 44 ~ 48.)
Note
3
Press or
NUMBER keys
to select the setting, and press
SET
.
2
Press (or )
to select
an item, and
press
SET
.
Selected disc information
Selected DECK information
Normal Screen
DISPLAY
button does not function while DVD MAIN
MENU or Direct Navigator or Play List is displayed.
When numbers are
displayed (e.g. title
number),
NUMBER keys
are also available.
If the number entered is
not on the disc, the entry
will have no effect.
Re-enter the correct
number.
For more details, refer to
the disc operation
information.
To return to normal
screen,
press
CLEAR
or
DISPLAY
repeatedly.
<Example of Video CD>
<Example of DVD-Audio>
<Example of DVD-Video>
<Example of DVD-RAM>
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4744
45
*
Important: if a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
DVD
Operation
Detailed Descriptions of each On-Screen Display
Disc information screen (for DVD-Video)
1. TITLE No.
Select TITLE, and press
SET
.
Change the No. by pressing or
NUMBER keys
, and press
SET
.
2. CHAPTER No.
Select CHAPTER, and press
SET
.
Change the No. by pressing or
NUMBER keys
, and press
SET
.
3. Disc currently being played
4. Elapsed playing time
The screen may be changed by selecting the elapsed time.
Select the elapsed playing time (xx:xx:xx), and press
SET
.
Change the elapsed time by pressing
NUMBER keys
.
Hours Minutes Seconds are entered in order.
If the time entered is not on the disc, the entry will have no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.
This function does not work with some discs.
Hour Minutes Seconds
Disc information screen (for DVD-Audio)
A.GROUP No.
Select GROUP, and press
SET
.
Change the No. by pressing or
NUMBER keys
, and press
SET
.
B.TRACK No.
Select TRACK, and press
SET
.
Change the No. by pressing or
NUMBER keys
, and press
SET
.
C.Disc currently being played
D.Elapsed playing time
The screen may be changed by selecting the elapsed time.
Select the elapsed playing time (xx:xx:xx), and press
SET
.
Change the elapsed time by pressing
NUMBER keys
.
Hours Minutes Seconds are entered in order.
If the time entered is not on the disc, the entry will have no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.
This function does not work with some discs.
Hour Minutes Seconds
When appears on the screen while a button is being operated, it means that the
corresponding operation is prohibited by DECK or the disc.
Note
4
SELECT:
SET : SET NEXT:DISPLAY
TI TLE : 1 DVD
CHAPTER: 12 01 :12: 55
1
2
3
D
A
B
ENTER : 0
-
9
SET : SET NEXT:DISPLAY
TI TLE : 1 DVD
CHAPTER: 12 01 :
--
:
--
ENTER : 0
-
9
SET : SET NEXT:DISPLAY
GROUP : 1 DVD-AUDIO
TRACK : 1 01:
--
:
--
If SET is pressed while
making entries, unit returns
to the condition it was in
before entries were made.
If SET is pressed
while making entries,
unit returns to the
condition it was in
before entries were
made.
C
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4745
46
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
SET : SET NEXT:DISPLAY
TRACK : 1 VIDEO CD
PBC : OFF 01:35 :12
PLAY L
I
ST: 1 DVD-RAM
00:12:34
SET : SET NEXT : DISPLAY
SELECT:
ENTER : 0
-
9
SET : SET NEXT:DISPLAY
PROGRAM: 1 DVD-RAM
01:
--
:
--
Disc information screen (for Video CD/ CD)
1. TRACK No.
Select TRACK, and press
SET*
.
Change the No. by pressing or
NUMBER keys
, and press
SET
.
2. Playback control ON/OFF
[Video CD with playback control only]
3. Disc currently being played
4. Elapsed playing time
Track No. and the elapsed playing time are not displayed during play started from
menu of Video CDs with playback control.
When appears on the screen while a button is being operated, it means that the
corresponding operation is prohibited by DECK or the disc.
1
2
3
4
Disc information screen (for DVD-RAM)
A.Direct Navigation (PROGRAM) or PLAY LIST No.
Select PROGRAM or PLAY LIST, and press
SET
.
Change the No. by pressing or
NUMBER keys
, and press
SET
.
B.Disc currently being played
C.Elapsed playing time
The screen may be changed by selecting the elapsed time.
Select the elapsed playing time (xx:xx:xx), and press
SET
.
Change the elapsed time by pressing
NUMBER keys
.
Hours Minutes Seconds are entered in order. If the time
entered is not on the disc, the entry will have no effect.
Re-enter the correct time.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.
This function does not work with some discs.
A
B
C
Hour Minutes Seconds
A
B
C
If SET is pressed while
making entries, unit
returns to the condition
it was in before entries
were made.
Direct Navigation
(PROGRAM)
PLAY LIST
DVD Operation using On-Screen Displays (continued)
Notes
Video CD CD
ON Video CD menu play is displayed.
OFF Video CD menu play is not displayed.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4746
47
DVD
Operation
1
. Repeat Play
DECK information screen (for DECK)
DVD-Video CHAPTER TITLE OFF
DVD-Audio TRACK GROUP OFF
DVD-RAM (PROGRAM) PROGRAM DISC OFF
(PLAY LIST) PLAY LIST ALL PLAY LIST OFF
Video CD/CD TRACK DISC OFF
Select REPEAT, and press
SET
.
Change the desired mode during play by pressing , and press
SET
.
*
Important: if a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
2
. Play mode [Video CD/ CD only] (See p. 39 or 40.)
SELECT:
SET : SET END : DISPLAY
PLAY
REPEATREPEAT : OFF
SET : SET END :DISPLAY
PLAY
REPEAT REPEAT : DISC
RANDOM PLAY
1
2
NUMBER
keys
SELECT
SET
PROGRAM PLAY program play
RANDOM PLAY random play
----
normal play
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4747
48
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DVD Operation using On-Screen Displays (continued)
CHAPTER/TITLE REPEAT PLAY (DVD-Video)
TRACK/DISC REPEAT PLAY (Video CD/CD)
For your reference
TRACK/GROUP REPEAT PLAY (DVD-Audio)
For repeat play in VCR mode, see p. 32.
Note
*
Important: if a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
PROGRAM/DISC REPEAT PLAY (DVD-RAM [PROGRAM])
PLAY LIST/ALL PLAY LIST REPEAT PLAY (DVD-RAM [PLAY LIST])
TITLE
chapter
chapter
chapter
CHAPTER REPEAT
TITLE REPEAT
NORMAL PLAY
CURRENT PLAYBACK POSITION
track
track
track
TRACK REPEAT
DISC REPEAT
NORMAL PLAY
CURRENT PLAYBACK POSITION
track
track
track
TRACK REPEAT
GROUP REPEAT
NORMAL PLAY
CURRENT PLAYBACK POSITION
track
track
track
GROUP
GROUP
PROGRAM
PROGRAM
PROGRAM
PROGRAM REPEAT
DISC REPEAT
NORMAL PLAY
CURRENT PLAYBACK POSITION
PROGRAM
PROGRAM
PROGRAM
PLAY LIST
PLAY LIST
PLAY LIST
PLAY LIST REPEAT
ALL PLAY LIST REPEAT
NORMAL PLAY
CURRENT PLAYBACK POSITION
PLAY LIST
PLAY LIST
PLAY LIST
OPEN/
CLOSE
SET
POWER
PLAY
SELECT
SKIP
SKIP
NUMBER
keys
ACTION
FF/REW
PAUSE
STOP
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4748
49
MP3/WMA/JPEG Playback Operation
DVD
Operation
ROOT
VA
TECHNO
POPS
J
AZZ
END
_
W
ALTZ
DD_CUB I C
N
O
CTURNE
N
O
RN
4
5
Select file (During STOP mode)
1)Press to select an MP3/WMA file (
/
).
MP3/WMA Playback (see right)
2)Press to select a JPEG file ( ).
JPEG Playback (see p. 50)
3)Press
SKIP
| (next) or |
SKIP
(previous) to skip a file/folder page (7files)
in the File area.
Select folder (During STOP mode)
1)Press to select a folder ( ).
2)Press
SET
to display files/folders contained
in the folder.
Select parent folder (During STOP mode)
1)Press to select a folder ( ).
2)Press
SET
to make changes to the previous
directory display.
Only File (not Folder) area
operation is possible.
Files are displayed in the
following order:
(!...0,1....9,A,B......Z).
Press
ACTION
to return to the DVD MAIN
MENU. (Press
ACTION
again to return
to the MP3/WMA/JPEG MENU.)
[PLAY MODE]
NORMAL:
All MP3/WMA files are selected and
played back one time only.
SINGLE REPEAT:
The selected MP3/WMA file is played
back repeatedly.
FOLDER REPEAT:
The MP3/WMA files contained in the
selected folder are played back
repeatedly. However, folders below the
selected folder are not played back.
DISC REPEAT:
All MP3/WMA files are played back
repeatedly.
Notes
MP3/WMA Playback
Forward/Reverse Search
Press
FF/SLOW+
or
REW/SLOW-
during play.
Press
PLAY
to release.
Search speed, slow at first, increases with each
additional press of the button up to 5 levels.
Forward/Reverse Track Skip
Press
SKIP
| or |
SKIP
during play.
Each press skips a track.
If pressed within first 3 seconds of playback,
skips to the previous track. If over 3 seconds,
returns to top of track. (|
SKIP
only.)
Put DECK in Stop mode before performing
folder/file selection (see step 4.)
Pause
Press
PAUSE
during play.
Press
PLAY
to release.
Press to select an MP3/WMA file (
/
).
(During STOP mode)
Press
SET
or
PLAY
to start playback.
a
b
c
d
Press
OPEN/CLOSE
to eject the disc.
The MP3/WMA/JPEG MENU is closed
automatically.
Press
STOP
to stop play.
Do steps 1~3 on left.
Copyright protected files and files
containing errors cannot be played
back. The DECK skips to the next file.
Note
Select PLAY MODE [MP3/WMA Playback]
(During STOP mode)
1) Press to move cursor to
PLAY MODE.
2) Press to select the desired PLAY
MODE (see below).
PLAY
PLAY MODE : NORMAL
00
:
00
:
00
ROOT
. .
VA
VA
END
_
W
ALTZ
TECHNO
DD
_
CUB I C
POPS
N
O
CTURNE
J
AZZ
N
O
RN
<Example>
Function
Status
Counter
PLAY MODE
Folder area
File area
Parent
folder
(Current folder
appears green.)
(Selected file/
folder is
highlighted.
Titles are
displayed
up to 11
characters.)
(Diagram left shows CD directory
structure as displayed in example
OSD above.)
<Example>
:MP3 file :WMA file
:Folder :Parent folder
:JPEG file
Notes
1
Press
POWER*
on the remote or DECK.
Press
OPEN/CLOSE
,
then place an MP3/WMA/JPEG disc into
the disc tray.
Press
OPEN/CLOSE
to close.
2
This unit can play MP3/WMA/JPEG format CD-R or
CD-RW recorded for personal use on a PC, etc.
Some discs may not play due to the condition of the
recording.
3
MP3/WMA/JPEG menu is displayed.
Playback starts automatically
(except JPEG files).
CD directory is displayed.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4749
50
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
MP3/WMA/JPEG Playback Operation (continued)
JPEG Playback
Press to select an JPEG file ( ).
1
Returned on the MP3/WMA/JPEG MENU
Press
STOP
. (See p. 49)
Next/Previous Search
Press
SKIP
| or |
SKIP
.
Start Slide-show Press
FF/SLOW+
or
REW/SLOW-
. (below)
Enlarging an image Press
ZOOM
. (P. 51)
Rotating an image Press
ANGLE
. (P. 51)
[JPEG Playback Screen]
Do steps 1~3 on page 49.
<Example>
Press
SET
or
PLAY
.
Selected JPEG file is displayed.
2
3
You can play back JPEG images.
Displayable Image Size: 32x32~7680x7680 pixels
Image changes every 3 seconds.
JPEG Slide-show
Press
FF/SLOW+
or
REW/SLOW-
.
1
<Example>
JPEG files are displayed automatically
(about every 3 seconds) as a slide-show.
Press
ACTION
to return to the DVD MAIN
MENU.
2
(During JPEG Playback.)
Cancel slide show
Press
STOP
to return to the MP3/WMA/
JPEG MENU. (See p. 49)
Still picture
Press
STILL
(only SLIDE).
Press
PLAY
to release.
Forward/Reverse File Skip
Press
SKIP
| or |
SKIP
.
Each press skips a file.
<Example>
REW/SLOW-
FF/SLOW+
Operation can be done when files are in
order, such as in the diagram below.
REW/SLOW-
FF/SLOW+
[PLAY MODE]
NORMAL:
All JPEG files are selected and
played back one time only.
SINGLE REPEAT:
The selected JPEG file is played back
repeatedly.
FOLDER REPEAT:
The JPEG files contained in the
selected folder are played back
repeatedly. However, folders below the
selected folder are not played back.
DISC REPEAT:
All JPEG files are played back
repeatedly.
ROOT
AAA
DDD
TTT
UUU
VVV
WWW
ZZZ
01 PIC
Some JPEG format may not be played
back.
Note
Press
STOP
to return to the MP3/WMA/
JPEG MENU.
Select PLAY MODE [JPEG Slide-show]
(During STOP mode) (See p. 49)
1) Press to move cursor to
PLAY MODE.
2) Press to select the desired PLAY
MODE (see below).
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4750
51
DVD
Operation
You can enlarge specific portions of a JPEG picture
and select the zoom ratio using the ZOOM button
on the remote during JPEG Playback screen.
Set Zoom size.
Press
ZOOM
repeatedly to change display as
follows.
Press
STOP
to return to the MP3/WMA/JPEG MENU.
You can enlarge the center portion of the image to
one of 2 magnifications.
Operation can be done during Rotation (below).
X 1.0 (ORIGINAL)
1st press
2nd press
3rd press
X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)
Use the , , and buttons to move the
position up, down, left and right.
(Position cannot be changed on X1.0
ORIGINAL images.)
JPEG Zoom
JPEG Rotation
(During JPEG Playback.)
Set rotation.
Press
ANGLE
repeatedly to change display
as below.
Press
STOP
to return to the MP3/WMA/JPEG
MENU.
(During JPEG Playback.)
You can rotate a JPEG picture using the ANGLE
button on the remote during JPEG Playback
screen. (The JPEG picture will be rotated 90 °
clockwise.)
2nd press 3rd press
Operation can be done during Zoom (above).
The vertical/horizontal ratio of rotated JPEG
images may vary when they are displayed.
1st press
4th press
SET
FF/
SLOW+
STOP
REW/
SLOW-
PLAY
SELECT
SKIP
SKIP
STILL
ACTION
ZOOM
ANGLE
MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and
Thomson multimedia.
Windows Media, and the Windows logo are trademarks, or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
WMA is a compression format developed by Microsoft Corporation. It achieves
the same sound quality as MP3 with a file size that is smaller than that of MP3.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4751
52
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
1
DVD Lock (DVD-Video only)
LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs, Video
CDs, WMA, MP3 and JPEG is prohibited.
(Use to prohibit play of mature theme DVDs not
encoded with rating level.)
LEVEL 1 : mature theme DVDs
LEVEL 2 : DVDs expressly for children can be played back.
LEVEL 3 to 7 : DVDs for general audiences/children can be
played back. (DVDs with mature content
are prohibited.)
LEVEL 8 : NO LIMIT: (Factory preset)
All DVDs can be played back.
You can prevent playback of DVDs of a specific
rating level which may be unsuitable for children.
Some DVDs are encoded with a rating level. If the disc
rating is higher (stricter) than the one you preset,
playback will be prohibited.
<When DVD Lock is activated>
After DVD Lock is set and a
blocked DVD is played, this
message will appear.
The message may differ
depending on the disc.
To continue viewing a blocked
program for now,
Press to select YES and
SET. Then, enter your 4 digit
secret code (see step 3 left).
When NO is selected, blocked
programs cannot be viewed.
DVD Lock Feature
SELECT:
SET : SET END : DISPLAY
,
YOUR SELECTION EXCEEDS THE
PLAYER S RATING LIMIT.
DO YOU WANT TO CHANGE THE
LIMIT?
YES
NO
Discs not encoded with rating
level will play even if the jacket
states it is for mature
audiences. For these discs, the
DVD Lock Ratings will not work.
Caution
4
Press
to select rating level, and
press
SET
to select LOCKED or
UNLOCKED.
A 4-digit code must be entered to view a blocked
program or change rating settings.
Press
ACTION
*
to display DVD MAIN MENU.
Press
to select PARENTAL LOCK,
and
press
SET
to display.
2
1) Press
NUMBER keys
to enter your secret code.
2) Enter same secret code
again for confirmation.
3) Press
SET
to display.
Step 2) not necessary when
changing rating or secret
code.
Take care that you are not
observed entering the
secret code.
To Make Corrections
Press repeatedly to
move the cursor.
Press
NUMBER keys
to
make the correction.
Change your secret code
You will need your current code.
Do steps 1 ~ 2 left.
Enter current secret code.
Press
CLEAR
to clear the code.
Do step 4 to enter new code.
DO NOT forget your secret code.
Note
3
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
STILL MODE : AUTO
TV MODE : 4:3 Letterbox
PARENTAL LOCK : LEVEL 8
*Important: If a remote control button does not work when
pressed, press the DVD button on the remote
and try the button again.
Ready Checklist
DECK is in DVD mode, press DVD.
ENTER
:
0
-
9
END
:
ACT
I
O
N
ENTER 4
-
D
I
G
I
T
CODE
----
PROGRAM RATING EXCEEDED
<When blocked programs>
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4752
53
Disc Languages (DVD only)
To select and set the language of the audio
soundtrack, subtitles, or title/DVD menus for all discs
to be played.
AUDIO selections
(Factory preset: English)
To select the audio soundtrack language.
English/Spanish/French/Japanese
Original: Original disc language
OTHER ✱✱✱✱: Other language selection*
1
SUBTITLE selections
(Factory preset: AUTO)
To select the subtitle language.
AUTO: Same language selected
for AUDIO
If language set for AUDIO is used in
playback, subtitles will not appear.
If another language is used during
playback, the subtitles will appear
in the language selected at AUDIO
setup.
English/Spanish/French/Japanese
OTHER ✱✱✱✱: Other language selection*
1
MENUS selections
(factory preset: English)
To select the language used in title
menus or DVD menus.
English/Spanish/French/Japanese
OTHER ✱✱✱✱:
Other language selection*
1
To enter OTHER ✱✱✱✱
code
number,
Press
NUMBER keys
(Please refer to
language codes on page 60).
To make corrections, press
repeatedly to delete language code
number, and correct.
Settings for DVD Operation
1
2
Once initial settings are done, they
remain in memory (even after power off)
until changed. This means DECK will
operate under the same conditions
(especially DVDs) each time.
DISC LANGUAGES (See below)
All languages offered on the disc can be set.
If the language not offered is set, the original disc
language will be selected.
AUDIO OUTPUT (See p. 54.)
You can set the audio output that comes from the
digital audio output terminal.
STILL MODE (See p. 57.)
To select FIELD (Field still) or FRAME (Frame
still) to prevent jitter or make small text or fine
patterns clearly visible in a still picture. When
AUTO is set FIELD or FRAME is selected
automatically.
TV MODE (See p. 57.)
To select whether the video material for a wide-
screen will be played back in the Pan & Scan style,
Letterbox style or 16 : 9 style.
3
Press
to select
DISC LANGUAGES,
and
press
SET
to display screen.
Press
ACTION
to display DVD MAIN MENU.
Press
to select an item, and
press
SET
.
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
STILL MODE :
AUTO
TV MODE : 4:3 Letterbox
PARENTAL
LOCK
:
LEVEL 8
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
STILL MODE :
AUTO
TV MODE : 4:3 Letterbox
PARENTAL
LOCK
:
LEVEL 8
Press
to select an item, and
press
SET
repeatedly
for desired language.
(Please refer right.)
4
DISC LANGUAGES
SELECT :
SET : SET
END : ACTION
AUDIO : Engl is h
SUBTITLE : AUTO
MENUS : English
5
Press
ACTION
to redisplay DVD MAIN
MENU and go to step 2 to setup another
item.
Or, press
ACTION
twice to exit.
*
1
If the selected language is not offered,
the original disc language is selected.
Ready Checklist
DECK is in DVD mode, press DVD.
DVD
Operation
SET
NUMBER
keys
CLEAR
ACTION
SELECT
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4753
54
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Make settings according to amplifier
connected to optical audio output as shown
in above table.
*1 When connecting an amplifier (with an
optical digital input connector) which does
not contain the Dolby Digital or DTS
decoder, be sure to select PCM.
If Bitstream is selected, starting DVD play
may cause such a high level of noise as to
be harmful to your ears and damage the
speakers.
*2 When a DTS decoder is connected, please
select Bitstream in dts.
Audio Output
Select the digital output to be output from the optical
digital audio output connector of DECK.
LPCM (DVD) selections
OFF: Linear PCM of less than 48 kHz/16 bit is
output. When playing DVDs recorded in linear
PCM of over 48 kHz/20 bit, no digital audio is
output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM of
48 kHz/20 bit/24 bit or more, digital audio
converted to 44.1 kHz/16 bit or 48 kHz/16 bit is
output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright protection.)
Dolby Digital selections
Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch) is
output. (Factory preset)
PCM: When you have connected a amplifier that
doesnt have a built-in Dolby Digital decoder.
dts selections
Bitstream: DTS bitstream is output. (Factory preset)
PCM: When you have connected a amplifier that
doesnt have a built-in DTS decoder.
DRC (Dynamic Range Compression)
selections
OFF: Normal audio range is selected. (Factory preset)
ON: For dynamic sound even at low volume, this is
useful for late-night listening. [Dolby Digital
DVDs only].
SPEAKER SETUP
See pages 55, 56, 57.
Press
to select an item,
and
press
SET
repeatedly for
output. (See below.)
Press
to select
AUDIO OUTPUT,
and
press
SET
to display screen.
1
Settings for DVD Operation (continued)
3
2
4
Recommended setting
LPCM
(DVD)
PCM
PCM
PCM
Dolby
Digital
PCM*
1
Bitstream
Bitstream
DTS
PCM*
1
PCM
Bitstream
No amplifier is connected
AV amplifier (with digital
audio input connector)
without Dolby Digital/DTS
decoder
AV amplifier including
Dolby Digital decoder
AV amplifier including
Dolby Digital/DTS decoder
*
2
Type of amplifier
to be connected
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
STI LL MODE : AUTO
TV MODE : 4:3 Letterbox
PARENTAL
LOCK
:
LEVEL 8
AUDIO OUTPUT
SELECT :
SET : SET
END : ACTION
LPCM(DVD) : OFF
Dolby Digital : Bitstream
dts : Bitstream
DRC : OFF
SPEAKER SETUP
Press
ACTION
to redisplay DVD MAIN
MENU and go to step 2 to setup another
item.
Or, press
ACTION
twice to exit.
Press
ACTION
*
to display DVD MAIN MENU.
Ready Checklist
DECK is in DVD mode, press DVD.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4754
55
*Important: If a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
AUDIO OUTPUT
SELECT :
SET : SET
END : ACTION
LPCM(DVD) : OFF
Dolby Digital : Bitstream
dts : Bitstream
DRC : OFF
SPEAKER SETUP
Speaker Size Setup
1
Speaker frequency properties and the existence of speakers is set.
Press
to select SPEAKER SIZE, and press
SET
to display SPEAKER SIZE screen.
Press
to select an item, and press
SET
repeatedly. (See below table.)
3
2
DVD
Operation
SET
ACTION
SELECT
SPEAKER SETUP
SELECT :
SET : SET
END : ACTION
SPEAKER OUTPUT : MULTI-CHANNEL
SPEAKER SIZE
OUTPUT BALANCE
DELAY TIME
Menu item
FRONT
CENTER
SURROUND
SUBWOOFER
Remark
Setting
LARGE(factory preset)
SMALL
LARGE(factory preset)
SMALL
NONE
LARGE(factory preset)
SMALL
NONE
ON(factory preset)
OFF
When the front speakers (R/L) supports low-frequency (under 100 Hz) reproduction.
Select when the front speakers (R/L) does not support low-frequency reproduction.
When the surround speakers (R/L) supports low-frequency (under 100 Hz) reproduction.
Select when the surround speakers (R/L) does not support low-frequency reproduction.
When the center speaker supports low-frequency (under 100 Hz) reproduction.
Select when the center speaker does not support low-frequency reproduction.
If there is no center speaker.
If there is no surround speaker.
If there is no subwoofer speaker.
If there is a subwoofer.
SPEAKER SIZE
SELECT :
SET : SET
END : ACTION
FRONT
: LARGE
CENTER : LARGE
SURROUND : LARGE
SUBWOOFER :
O
N
Press
ACTION
four times to exit.
Speaker Output Setup
1
Press
to select SPEAKER
SETUP, and
press
SET
to display
SPEAKER SETUP
screen.
2
Set the number of speakers connected to the receiver
(amplifier, decoder.) (See pp. 14, 15.)
Do steps 1~3 on page 54.
Press
to select SPEAKER
OUTPUT,
and
press
SET
repeatedly.
(See below.)
SPEAKER OUTPUT
MULTI-CHANNEL: (Factory preset)
Use this setting when 3 or more speakers are
connected. In this case, it is necessary to set
[SPEAKER SIZE], [OUTPUT BALANCE], and
[DELAY TIME].
2-CHANNEL:
When 2 speakers are connected, it is not
necessary to set [SPEAKER SIZE], [OUTPUT
BALANCE], and [DELAY TIME] (these setting
menu are not displayed.)
4
Press
ACTION
three times to exit.
3
**If SUBWOOFER is set to OFF,
the front speakers are set to
LARGE automatically.
Do steps 1~2 of Speaker Output Setup above.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4755
56
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Output Balance Setup
1
Adjust the volume level output from the speakers. To adjust, play a disc or set the TEST SIGNAL
(p.57) to ON. Then adjust while confirming the volume. (Even if OFF or "NONE" is set in SPEAKER
SIZE, the speaker OUTPUT BALANCE can still be set.)
2
Settings for DVD Operation (continued)
Delay Time Setup
1
To enjoy 5.1 CH sound, it is ideal to place all
speakers, except the subwoofer, in a circular
arrangement. (See <Speaker Position> p. 57.)
If this is not possible, setting Delay Time gives the
sound output a delayed effect which gives you the
illusion of the ideal listening position. (See right.)
2
3
Press
ACTION
three times to exit.
Press
to select OUTPUT BALANCE, and press
SET
to display OUTPUT BALANCE screen.
Press
to select an item, and press
SET
repeatedly.
(See below table.)
Press
to select DELAY TIME, and press
SET
to display DELAY TIME screen.
Press
to select an item, and press
SET
repeatedly. (See below.)
OUTPUT BALANCE
SELECT :
SET : SET
END : ACTION
CENTER
: 0dB
SURROUND(R) : 0dB
SURROUND(L) : 0dB
SUBWOOFER : 0dB
TEST SIGNAL : OFF
Menu item
SURROUND
CENTER
Remark
Setting
0ms 1ms 2ms 3ms 4ms 5ms
0ms(Factory preset)
Setting a delay effect.
0ms 5ms 10ms 15ms 20ms
Distance
Setting
B1
Approx. 50 cm (1 feet)
1
/2
Approx. 100 cm (3 feet)
1.3 ms
2.6 ms
3.9 ms
5.3 ms
Approx. 150 cm (5 feet)
Approx. 200 cm (6 feet)
C1
Distance
Setting
Approx. 200 cm (6 feet)
Approx. 400 cm (12 feet)
5.3 ms
10.6 ms
15.9 ms
Approx. 600 cm (18 feet)
B1
Center speaker
C1
Surround speaker
, : Delay time as 0ms
(Factory prest)
, < : Find the distance
B1
,
C1
in the
table (below) and change to
the recommended setting.
[See <Speaker Position> p.57.]
3
Press
ACTION
four times to exit.
Menu item
SUBWOOFER
SURROUND(L)
SURROUND(R)
CENTER
Remark
Setting
-6dB
~
+6dB
0dB(factory preset)
Adjust so that the center speaker volume is virtually the same
level (-6dB ~ +6dB) as the front speakers.
Adjust so that the surround speaker(R) volume is virtually
the same level (-6dB ~ +6dB) as the front speakers.
Adjust so that the surround speaker(L) volume is virtually
the same level (-6dB ~ +6dB) as the front speakers.
Adjust so that the subwoofer speaker volume is optimum.
However, because no test sound will come from the
subwoofer, play a disc to confirm, then adjust.
TEST SIGNAL : Switch test signal used for OUTPUT BALANCE setting to OFF or FRONT(L)....
See page 57.
Do steps 1~2 of Speaker Output Setup on page 55.
Do steps 1~2 of Speaker Output
Setup on page 55.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4756
57
Press to select TV
MODE, and press
SET
repeatedly for
mode.
(See below.)
2
4:3 Pan & Scan (Factory preset) :
Wide-screen video data is played in
Pan & Scan style (left and right of screen
is trimmed.)
Video data not formatted in Pan & Scan
will play in letterbox style.
4:3 Letterbox :
Wide-screen video data is played in
Letterbox style (top and bottom of screen
has black margin).
16:9 :
Set 16:9 when using Wide-screen TV.
Press
ACTION
to exit this mode.
3
*Important: If a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
[Letterbox]
TV Mode
Example
DVD
Operation
[Pan & Scan (Factory preset)]
Test Signal Setup
1
This feature assists in the setting of
OUTPUT BALANCE. Starting with (L) front
speaker, a test sound is output in clockwise
order. While the test signal is output, adjust
the output of the center speaker and
Surround speaker (R/L).
(See OUTPUT BALANCE. P. 56.)
Press
to select TEST
SIGNAL, and
press
SET
.
(See below.)
3
Press
ACTION
four times to exit.
2
No sound will come from the subwoofer.
Adjust as desired when playing a disc.
While the TEST SIGNAL is output, if the
setting change in the OUTPUT BALANCE (p.
56) is under 2 seconds, the output will switch
to the next speaker. The speaker name from
which the TEST SIGNAL is currently being
output is displayed.
(Example; "TEST SIGNAL : CENTER")
OUTPUT BALANCE
SELECT :
SET : SET
END : ACTION
CENTER : 0dB
SURROUND(R) : 0dB
SURROUND(L) : 0dB
SUBWOOFER : 0dB
TEST SIGNAL
: OFF
Still Mode
1
Press
to select STILL MODE,
and
press
SET
repeatedly
for mode. (See below.)
2
AUTO: FIELD (Field still) or FRAME (Frame still) is
automatically selected during the still mode.
(Factory preset)
FIELD: FIELD (Field still) is always selected.
This setting will reduce jitter when compared
with AUTO on some discs.
FRAME:FRAME (Frame still) is always selected.
Some texts and fine patterns will be seen clearly
when compared with AUTO on some discs.
TV Mode
1
Set the screen display style for wide-screen video
material playback.
Set to reduce jitter in a displayed still picture or a motion
picture.
3
Press
ACTION
to exit this mode.
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
STI
LL
MODE
: AUTO
TV MODE : 4 :3 L et t er b ox
PARENTAL
LOCK
:
LEVEL 8
Press
ACTION
to display DVD MAIN MENU.
Press
ACTION
to display DVD MAIN MENU.
CENTER
FRONT(R)
SUBWOOFER
FRONT(L)
Listening
position
SURROUND(R)
SURROUND(L)
B1
C1
FRONT(L) CENTER FRONT(R)OFF
SURROUND(L) SURROUND(R)
2sec 2sec
2sec
2sec
2sec
<Speaker Position>
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
STI LL MODE : AUTO
TV MODE : 4:3 L et t er b ox
PARENTAL
LOCK
:
LEVEL 8
Do steps 1~2 of Output
Balance Setup on page 56.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4757
58
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
TIMER REC
SELECT : SET : SET
EXIT : ACTION PAGE : SKIP
+/
-
SINGLE
SLIDE
1
/
3
SD Card
JPEG Playback
Still image data (JPEG) made with a digital camera, digital video camera, or PC can be played back
using an SD Memory Card/MultiMediaCard.
Compatible Card : An SD Memory Card and MultiMediaCard can be used in this DECK.
Displayable Image Formats : DCF format 1.1 compliant
Baseline JPEG format Y Cb Cr (compressed format)
(Sampling ratios 4:4:4, 4:2:0, 4:2:2, 4:1:1)
(80 x 60 ~ 5120 x 3840 pixels)
Exif2.1 image data contained in [IMEXPORT] folder used for data
transfer bitween the equipment with SD Memory Card.
JPEG files altered and saved on a PC as grayscale format cannot be displayed.
Some parts of an image may not be displayed or the image may be displayed on a
smaller scale depending on the size of the image.
Notes
1
Insert the SD Card.
SD MENU is displayed
automatically. If SD
MENU is not displayed,
reinsert the SD Card.
<DVD mode, VCR mode>
<If in VCR mode with SD
card already inserted.>
or
Press ACTION.
Press
to select SD CARD
PLAYBACK.
Press SET
to display.
During Timer REC, the above menu
is not displayed. To display the SD
Menu, reinsert the SD Card.
Note
SELECT :
EXIT
: ACTION
SET:SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
SD CARD PLAYBACK
IDIOMA/LANGUE : ENGLISH
VCRS OUTPUT CH:3
2
SD appears when in SD mode.
Multi Function Display
INDEX AREA
This area is used to
display the files stored
within the SD Card.
Return to VCR Mode,
Press ACTION.
SD MENU DISPLAY
SINGLE PLAY
A single image, selected from the index area, can be enlarged and played back. Also, functions,
such as zoom, rotation and applying image information can be performed.
See SINGLE PLAY mode on page 59.
SLIDE SHOW
A slide show presentation can be composed, including various image transition effects and
transition speeds.
See SLIDE SHOW mode on page 59.
SINGLE PLAY
SLIDE SHOW
DISPLAY
PAGE No.
Up to 1000 files can be
displayed.
Note
•“SD blinks while data is being read.
Note
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4758
59
DVD
Operation
DVD
Operation
SINGLE PLAY mode
1
Press to select
SINGLE, and press SET.
Press
to move
cursor to desired file in
INDEX AREA.
(Press SKIP +/
-
to display
next/previous page of 9
thumbnail files),
Press SET to display file in
large size.
Press SKIP+
next image.
Press SKIP-
previous image.
ZOOM (Enlarge Image)
Image can be displayed 2 or 4 times normal size.
Press ZOOM repeatedly.
ROTATE
Image can be rotated clockwise in 90° increments.
Press ANGLE repeatedly.
Start Slide-show Press PLAY. (See below.)
Display file information screen Press DISPLAY.
Do steps 1 - 2 on p. 58.
2
Press ACTION
to exit this mode.
SELECT : SET : SET
END : ACTION PAGE : SKIP
+/
-
SINGLE
1
/
3
SLIDE SHOW mode
1
Do steps 1 - 2 on p. 58.
Press to select
SLIDE, and press SET.
Press
to move
cursor to desired file in
INDEX AREA.
(Press SKIP +/
-
to display
next/previous page of 9
thumbnail files).
Press SET to display
SLIDE MENU.
Press
to select an
item (see right), and press
SET repeatedly to set.
2
START SLIDE SHOW.
3
Press ACTION
to exit this mode.
PAUSE
Press PAUSE. Press PLAY to relese.
Press SET to return SLIDE MENU (above).
SLIDE MENU
SELECT : SET : SET
END : ACTION
START
SPEED : FAST 2S
TRANSITION : NORMAL
...
Once selected, image is displayed
in about 3 sec. ( appears while
data is read. DO NOT remove SD
Card during data reading.)
Deck buttons are inoperative.
Use remote control.
If cursor is at top of the INDEX
AREA, pressing selects previous
page. If cursor is at bottom of the
INDEX AREA, pressing selects
next page.
If Rotate is operated while Zoom (X2
or X4) is displayed, the unit will revert
to X1 (ORIGINAL) magnification.
Notes
X 1.0 (ORIGINAL)
1st press
2nd press
3rd press
X 2 (ZOOM 1) X 4 (ZOOM 2)
F I LE : 12345
DATA : 05/16/2003
SIZE : 500KBYTE
PIXEL : 640480
ZOOM : NORMAL
ROTATE: 0
.
NEXT : SKIP+
ZOOM : ZOOM
SLIDE : PLAY
PREV : SKIP-
ROTATE
: ANGLE
END : ACTION
File information screen
[START]
Starts slide show.
[SPEED]
FAST:
Image transition every
2 seconds.
MEDIUM:
Image transition every
5 seconds.
SLOW:
Image transition every
10 seconds.
[Transition]
NORMAL:
Image transition one by one.
WIPE:
Image transition from top to bottom.
SPLIT:
Image transition beginning at the center
and splitting to the left and right.
BLIND:
Image transition in a series of band-like
shapes that resemble window blinds.
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4759
60
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Language Code List
Enter the appropriate code number for the initial settings AUDIO, SUBTITLE and/or
MENUS (see p. 53).
Code Language
7079 Faroese
7082 French
7089 Frisian
7165 Irish
7168 Scots Gaelic
7176 Galician
7178 Guarani
7185 Gujarati
7265 Hausa
7273 Hindi
7282 Croatian
7285 Hungarian
7289 Armenian
7365 Interlingua
7378 Indonesian
7383 Icelandic
7384 Italian
7387 Hebrew
7465 Japanese
7473 Yiddish
7487 Javanese
7565 Georgian
7575 Kazakh
7576 Greenlandic
7577 Cambodian
7578 Kannada
7579 Korean
7583 Kashmiri
7585 Kurdish
7589 Kirghiz
7665 Latin
Code Language
7678 Lingala
7679 Laothian
7684 Lithuanian
7686
Latvian, Lettish
7771 Malagasy
7773 Maori
7775 Macedonian
7776 Malayalam
7778 Mongolian
7779 Moldavian
7782 Marathi
7783 Malay
7784 Maltese
7789 Burmese
7865 Nauru
7869 Nepali
7876 Dutch
7879 Norwegian
7982 Oriya
8065 Panjabi
8076 Polish
8083
Pashto, Pushto
8084 Portuguese
8185 Quechua
8277
Rhaeto-Romance
8279 Romanian
8285 Russian
8365 Sanskrit
8368 Sindhi
8372
Serbo-Croatian
8373 Singhalese
Code Language
8375 Slovak
8376 Slovenian
8377 Samoan
8378 Shona
8379 Somali
8381 Albanian
8382 Serbian
8385 Sundanese
8386 Swedish
8387 Swahili
8465 Tamil
8469 Telugu
8471 Tajik
8472 Thai
8473 Tigrinya
8475 Turkmen
8476 Tagalog
8479 Tonga
8482 Turkish
8484 Tatar
8487 Twi
8575 Ukrainian
8582 Urdu
8590 Uzbek
8673 Vietnamese
8679 Volapük
8779 Wolof
8872 Xhosa
8979 Yoruba
9072 Chinese
9085 Zulu
Code Language
6565 Afar
6566 Abkhazian
6570 Afrikaans
6577 Ameharic
6582 Arabic
6583 Assamese
6588 Aymara
6590 Azerbaijani
6665 Bashkir
6669 Byelorussian
6671 Bulgarian
6672 Bihari
6678
Bengali; Bangla
6679 Tibetan
6682 Breton
6765 Catalan
6779 Corsican
6783 Czech
6789 Welsh
6865 Danish
6869 German
6890 Bhutani
6976 Greek
6978 English
6979 Esperanto
6983 Spanish
6984 Estonian
6985 Basque
7065 Persian
7073 Finnish
7074 Fiji
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4760
61
These displays will alert you to a missed operation or provide further instructions.
Warning and Instruction Displays
PLEASE SET CLOCK BY
PRESSING ACTION KEY
CHECK CASSETTE
RECORD TAB
NO CASSETTE
VIDEO HEADS MAY NEED
CLEANING PLEASE INSERT
HEAD CLEANING CASSETTE
OR REFER TO MANUAL
END : PLAY
VCR LOCK ACTIVATED
Page
CautionOSD
If you attempt to set or review a Timer
Recording and the Clock is not set...
REMOTE CONTROL IS SET
TO TV MODE
USE VCR : VCR KEY
USE DVD : DVD KEY
REMOTE CONTROL IS SET
TO CABLE/DSS MODE
USE VCR : VCR KEY
USE DVD : DVD KEY
PLEASE PREPARE FOR TIMER
REC
PLEASE CHECK THE DISC,
AND FOR STAINS OR
SCRATCHES ON DISC
IT IS PROHIBITED TO COPY
DVD/VIDEO CD/CD TO VHS
TO CANCEL TIMER REC
HOLD DOWN STOP KEY
FOR APPROX 3 SEC
24
24
25
6
20
21
25
4
33
28
29
34
6
28
29
34
For Your
Information
THIS DISC MAY NOT BE PLAYED
IN YOUR REGION
THIS TYPE OF DISC CANNOT BE
PLAYED. PLEASE INSERT A
DIFFERENT DISC
3
6
CANNOT PLAY THIS FILE
49
49
DATA ERROR
CARD ERROR
If DECK is not in Stop mode or a cassette with
record tab is not inserted 2 minutes before a
Timer Recording is about to begin...
If you press REC on the remote control or DECK,
and a cassette is inserted with no record tab...
If you press PLAY, FF, REW, or REC on the
remote control or DECK without a cassette
inserted...
If you press STOP or POWER during a Timer
Recording...
(visible in VCR mode only)
If head cleaning becomes necessary while
playing back a tape...
If you press a function button other than STOP/
EJECT or POWER while DECK is
in VCR Lock mode...
If you press an invalid key on the remote while
in CABLE/DSS mode...
If you press an invalid key on the remote while
in TV mode...
If you press PLAY, and DECK reads data from a
stained or scratched disc in DVD mode.
Playback of a disc with different region number
was attempted. Only discs marked region 1,
ALL, or those that include 1 are playable on
this DECK.
An unusable disc is inserted in the DECK.
This file format cannot be played.
(Appears during MP3/WMA/JPEG file playback)
THIS FILE IS PROTECTED
This file is copyright protected and cannot be
played back. (Playback is prohibited.)
(WMA only)
If you press REC in DVD mode...
An image file could not be displayed. The file is
corrupt or the format is incompatible.
SD Memory Cards that have been formatted to
FAT32 specifications cannot be used.
21
58
58
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4761
62
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before Requesting Service
Power
No power
Power turns itself off...
Recording & Playback
TV program cannot be recorded...
Timer recording cannot be
performed
There is no playback picture, or the
playback picture is noisy or contains
streaks...
During special effects playback,
picture may contain some vertical
jitter when using a TV with an
Automatic Vertical Hold Control...
DECK cannot be controlled...
Check the following points if you are having trouble with your DECK.
Correction
Completely insert Power Plug into an AC outlet.
Set POWER button to on.
Make sure power source is active.
Auto power-off (shutoff) occurs after about 5 min.
in DVD mode with no operation, or if there is no
broadcast signal in TV or Playback mode.
Turn the power back on. (pp. 23, 33)
Correction
Check connections between DECK, external
antenna, and TV.
Check channel selections.
Make sure your antenna system (CABLE or TV) is
correctly set. (Channels [p. 18])
Make sure cassette record tab is intact. (p. 6)
Confirm that clock is set to current time and date.
Make sure Cable/DSS box (if used) is left on and
tuned to channel to be recorded.
Set recording start/stop times correctly. (p. 24)
Timer recording may not be performed or continued
if a power interruption occurs before or during a
Timer Recording, even after power is restored.
Select channel 3 or 4 on TV to match VCR output
channel (3 or 4) (p. 16) or select LINE.
Set VCR/TV selector to VCR.
Adjust TRACKING control in either direction. (p. 4)
Try Head Cleaning. (p. 4)
Set TVs Vertical Hold Control to MANUAL, then
adjust.
Make sure DECK power is on.
Check Remote batteries.
Make sure VCR LOCK is set to off. (p. 33)
Make sure Remote is in proper mode. (p. 28)
Make sure Timer Recording is not in progress.
Remote Control
DECK cannot be remote controlled...
PROG buttons do not respond...
Correction
Make sure DECK power is on.
Make sure Remote is in VCR mode.
Aim Remote Control directly at remote sensor on DECK. (p.9)
Avoid any object blocking signal path.
Check Remote batteries. (p. 4)
Exposing DECK remote sensor to direct fluorescent
or outdoor light may cause signal interference.
PROG functions are not available in COMPONENT
Video Output and S-VIDEO OUT. Set TV to either RF
IN or VIDEO IN. (p. 10)
Check Remote batteries. (p. 4)
Press VCR or DVD button for DVD/VCR mode. (p. 28)
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4762
63
Check the following points if you are having trouble with your DECK.
Miscellaneous
Programs cannot be viewed on TV...
Video cassette cannot be inserted...
Video cassette ejects when
a recording is started or the power is
turned off for timer recording...
In Stop mode, the motor (CYLINDER)
continues to rotate...
The disc cannot be removed..
Correction
Make sure TV is set to output of DECK.
Check connections between DECK,
external antenna, and TV.
Set VCR/TV selector to TV. (p. 21)
Make sure proper signal source is selected.
Insert the cassette with window side up; record
tab facing you.
Make sure cassette record tab is intact. (p. 6)
To enable Quick play mechanism, the cylinder will
rotate for about 3 minutes. This reduces response
time from Stop to Play mode.
First, unplug DECK. Then, prepare a rigid wire
(e.g. an extended paper clip) and, applying
moderate force, insert it straight into the hole at the
base of the tray. The tray will eject a little. Now, pull
the tray all the way out and remove the disc. (p. 9)
DVD/ Video CD/ CD
Play fails to start even when PLAY is
pressed...
Play starts but then stops immediately...
Picture is distorted during rapid
advance or rapid reverse...
No Forward/Reverse Scene Search
play...
Play does not start even when title is
selected...
Audio soundtrack and/or subtitle
language is not the one selected at
the initial settings...
No subtitles...
Alternative audio soundtrack
(or subtitle) language cannot be
selected...
Angle cannot be changed...
Correction
This DECK cannot play discs other than DVDs,
Video CDs and CDs.
The disc may be dirty and require cleaning.
Be sure disc is installed with label side up.
The picture will be somewhat distorted at times:
this is normal.
Some discs may have sections which prohibit
Forward/Reverse Scene Search. (p. 23)
Confirm the DVD LOCK setting. (p. 52)
If the audio soundtrack and/or subtitle language
selected at DVD initial settings does not exist
on the disc, it will not be accessible.
Subtitles appear only when available on disc.
•“OFF is selected at the changing subtitle
language. Select ON at the Subtitle Languages
section (p. 36) to display the subtitles.
Alternative language cannot be selected with discs
which do not contain more than one language.
For some discs, alternative language cannot be
selected with the AUDIO or SUB TITLE button.
Try selecting it from the DVD MAIN MENU if available.
This function is dependent on software availability.
Even if disc has multiple angles, they may be
recorded for specific scenes only (ANGLE
indicator on DECK lights up). (p. 37)
If you cannot resolve the problem, please call the Customer Call Center for product
assistance at 1-800-211-PANA (7262).
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).
or send e-mail to : [email protected]
For Your
Information
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4763
64
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Limited Warranty
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way
Secaucus, New Jersey 07094
PANASONIC SALES COMPANY,
DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park
Carolina, Puerto Rico 00985
Panasonic DVD/VCR Deck Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)
will, for the length of the period indicated on the chart below, which starts with the date of original purchase
(“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b)
replace it with a new or a refurbished product. The decision to repair or replace will be made by the
warrantor.
During the “Labor” Limited Warranty period there will be no charge for labor. During the Parts” warranty
period, there will be no charge for parts. You must mail-in your product during the warranty period.
If non-rechargeable batteries are included, they are not warranted. This Limited Warranty only applies to
products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended
only to the original purchaser and only covers product purchased as new. A purchase receipt or other
proof of original purchase date is required for Limited Warranty service.
Mail-In Service
For assistance in the continental U.S.A. in obtaining repairs please ship the product to:
Panasonic Services Company
Customer Servicenter
Suite B
4900 George McVay Drive
McAllen, TX 78503
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original
carton. Include a letter detailing the complaint and provide a day time phone number where you can be
reached.
IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE PURCHASER WILL BE
REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF
PURCHASE, AMOUNT PAID AND PLACE OF PURCHSE. CUSTOMER WILL BE CHARGED FOR THE
REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Product or Part Name
DVD/VCR Deck
Rechargeable Batteries
(in exchange for defective item)
Labor
Ninety (90) Days
Not Applicable
Parts
One (1) Year
Ten (10) Days
D4763S P36-60 (030610 –§”Ô•Ï•X2nd).p65 2003/06/10, 18:5964
65
For Your
Information
Limited Warranty Limits And Exclusions
This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES
NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT
COVER damages which occurred in shipment, or failures which are caused by products not supplied
by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling,
misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls,
improper maintenance, power line surge, lightning damage, modification, or commercial use (such as
hotel, office, restaurant, or other business), rental use of the product, or service by anyone other than
a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having
someone remove or re-install an installed unit if applicable, travel to and from the servicer, loss of or
damage to media or images, data or other recorded content. The items listed are not exclusive, but
are for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied Limited Warranty lasts, so the exclusions may not apply to you.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary
from state to state. If a problem with this product develops during or after the Limited Warranty period,
you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then
write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR
RESPONSIBILITY.
Customer Services DirectoryCustomer Services Directory
For Product Information, Operating Assistance, Literature Request, Dealer Locations, and
Customer Service inquiries please visit Web Site:
http://www.panasonic.com
You can purchase parts, accessories, locate your nearest servicenter and more by visiting our Web Site
or E-mail us via web:
http://www.panasonic.com/consumer_electronics/support/customerfeedback.asp
Contact:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
1-800-332-5368 (Customer Orders Only)
1-800-237-9080 (Fax Only)
(Monday-Friday 9 am-8 pm, EST.) Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(Accepts Visa, MasterCard, Discover Card, American Express, and Personal Check)
http://www.pasc.panasonic.com or email to [email protected]
For hearing or speech impaired TTY users, TTY : 1-877-833-8855
As of May 2003
Accessory Purchases
For hearing or speech impaired TTY users, TTY : 1-866-605-1277
Customer Services Directory
D4763S P36-60 (030610 –§”Ô•Ï•X2nd).p65 2003/06/10, 18:5965
66
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Spanish Quick Use Guide/ Guía para rápida consulta
Para ajustar el idioma, canal yPara ajustar el idioma, canal y
CONEXIONES/CONFIGURACION INICIAL (READY TO PLAY)
Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.
EL DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.
CONEXIONES
Conecte el cable de la antena al terminal IN
FROM ANT del DVD/VCR.
Conecte el terminal OUT TO TV del DVD/VCR
a la entrada de la antena VHF/UHF del TV con
el cable RF incluido.
Para Ant/Cable
DVD/VCR
TV
Para Sistema Digital de Satelite (DSS)/ Convertidor de cable
DVD/VCR
TV
Conecte la salida de convertidor de cable
al terminal IN FROM ANT.
Conecte el terminal OUT TO TV del DVD/VCR
a la entrada de la antena VHF/UHF del TV con
el cable RF incluido.
2
1
2
1
CONFIGURACION INICIAL
Encienda el TV y cambie al canal 3.
Enchufe el cable de CA.
El DVD/VCR se encenderá e iniciará las
fijaciones de los canales y del reloj.
Si no aparece la pantalla de abajo, compruebe
la conexión del DVD/VCR-TV y si el canal del
TV está a 3, intennte cambiando al canal 4.
Para cambiar el canal de salida del DVD/VCR,
consulte las instrucciones de Canal de salida
del VCR (informaciones en inglés página 19).
Enchufe el cable de CA.
1
2
DVD/VCR
VHF/UHF
Estuche convertidor
de TV por cable
Televisor
Terminal
IN FROM ANT.
Entrada (IN) desde
ANT./CABLE
Terminal
OUT TO TV
Terminal IN FROM ANT.
Televisor
DVD/VCR
VHF/UHF
Terminal
OUT TO TV
Entrada (IN) desde
ANT./CABLE
2
1
Si está usanndo un convertidor de TV por cable y
en su area hay un canal de Public Broadcast
Station (PBS), ajuste su convertidor al canal PBS
de su area. Si está usando un receptor DSS, este
debe estar apagado.
AJUSTE MANUAL DEL RELOJ
Si la fijación ha sido incompleta.
Presione la tecla ACTION en el control remoto
para visualizar la pantalla del menú SET
CLOCK.
1
Presione para seleccionar el mes y SET
para ajustar. De la misma forma, seleccione y
ajuste la fecha, año, hora y DST (hora de
verano).
2
1
2
3
Presione dos veces la tecla ACTION para
poner el RELOJ en marcha y salir.
Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]
Al inicio, el idioma de la
pantalla está fijado a
inglés.
Para cambiar el idioma,
seleccione la pantalla
MENU (informaciones en
inglés página 18).
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
CH AUTO SET PROCEEDING
CANCEL : STOP
PRECAUCIÓN
Al usar cables coaxiales RF del tipo tuerca,
apriételos solamente con los dedos. Un apriete
excesivo puede dañar los terminales.
Nota
Los botones de funciones no funcionan durante
la configuración inicial.
Para retirar un cassette durante el ajuste
automático, presione EJECT en el control remoto
o STOP dos veces en el aparato. En este caso,
los ajustes de los canales y la hora se deben
hacer manualmente. Para los ajustes seleccione
la pantalla MENU (informaciones en inglés
página 18).
Dependiendo de las condiciones, el ajuste
automático puede durar más de 30 minutos.
En ese caso, presione STOP para detener el
ajuste automático y realice los ajustes
manualmente en la pantalla MENU.
D
ST
:
ON
6
/
8
/
2003
SUN
2
:
2
0
P
M
SET
CO
M
P
L
E
T
E
D
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
SET
C
L
OC
K
DST
:
O
N
SESE
L
E
C
T
M
O
N
TH
1
/ /
:
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
SET
C
L
OC
K
Las fijaciones se realizan automáticamente.
Cuando termina las fijaciones, aparecerá la
siguiente pantalla.
Si aparece en la pantalla AUTO CLOCK SET IS
INCOMPLETE (FIJACION AUTOMATICA DEL
RELOJ ES INCOMPLETO), Ajuste el reloj
como se describe a continuación.
3
AUTO CLOCK SET IS
I
NC
O
M
PLETE
PLEASE SET CLOCK BY
PRESSING
ACT
I
ON KEY
6
/
8
/
20
03
SUN
2
:
20P
M
D
S
T
:
ON
SETT
I
N
G
: CH
10
AUTO CLOCK SET
C
O
M
PLETED
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4766
67
Operaciones básicas para la reproducción
1
2
3
Inserte un cassette,
La alimentación del DECK se activa.
En la Pantalla de Visualización Multi
Función se ilumina VCR.
Presione PLAY para reproducir el cassette.
Si el cassette no tiene la lengüeta de
prevención de grabación (página 6), se
inicia la reproducción automáticamente.
Detalles especiales durante la grabación
Presione FF/SLOW+ o REW/SLOW- para
búsqueda de escenas hacia delante/ hacia
atrás. Presione PLAY para liberar. Durante
la búsqueda, cada vez que presione FF/
SLOW+ o REW/SLOW- se cambia la
velocidad como sigue:
[SLP] aprox. 21X
aprox. 9X
[LP] aprox. 9X
aprox. 7X
[SP] aprox. 7X
aprox. 3X
Si la imágen se interrumpe con la velocidad de
21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x.
Presione PAUSE/STILL para imagen Fija
(Congelada).
Presione PLAY para liberar.
Presione PAUSE/STILL en el modo de
imagen fija para imágenes cuadro a cuadro.
Presione PLAY para liberar.
Presione FF/SLOW+ o REW/SLOW- en el
modo de imagen fija para cambiar la
velocidad de las imágenes a cámara lenta.
Presione STOP para detener el cassette.
Presione REW/SLOW- o FF/SLOW+ en el
modo de parada para rebobinado/avance
rápido del cassette.
Presione EJECT en el control remoto,
o STOP/EJECT en el DECK para expulsar
el cassette.
Operaciones básicas para la grabación
1
Inserte el cassette con lengüeta de
protección de grabación (página 6).
Presione CH / , o las teclas de números
para seleccionar el canal.
Presione SPEED para seleccionar la
velocidad de grabación (página 6).
Presione REC para comenzar a grabar.
Para eliminar escenas indeseadas, presione
PAUSE/STILL para hacer una pausa, y al
presionar nuevamente continua la grabación.
No podrá ver otro canal durante la
grabación.
Presione STOP para detener la grabación.
SP = Reproducción estándar,
LP = Larga duración,
SLP = Superlarga duración.
2
3
4
5
Grabación de un toque
Presione REC repetidamente para ajustar la
hora de grabación (30 min - 4 horas).
La videograbadora termina la grabación
a una hora programada.
Grabación normal
0:30 1:00
1:302:003:004:00
Programación fácil para la
grabación con temporizador
1
2
3
Presione PROG
para visualizar la pantalla de Programacion.
1) Para ajustar la FECHA de
grabación, presione
para seleccionar:
1-31 = una vez, o
DIARIO = a la misma hora
de lunes a viernes, o
SEMANA = a la misma
hora cada semana y
presione SET para ajustar.
2) Para ajustar los ítems que quedan,
presione para seleccionar y presione
SET para ajustar los tiempos de INICIO/
PARADA, CANAL, o entrada de LINEA (página
35), y velocidad del cassette (SP, LP, SLP).
Presione PROG para finalizar PROGRAM.
Presione
para seleccionar un número
que no está usando para
ingresar mas programas y
presione SET
para ajustar.
Luego repita el paso 2.
O
Presione nuevamente
PROG para salir.
Fecha de hoy
Orden para elegir
Ejemplo
FECHA
I
N
I
C
I
O
PARADA
C
A
7
SAB
--:--
--:--
--
HOY
ELEGIR
:
FIJAR
:
SET
TERMINAR
:
PROG
SLP
ELEGIR FECHA DE I
N
I
C
I
O
DIARIO
7
2
1
31
68 9
/ Orden para elegir
SEMANAL
(
SAB
)
SEMANAL
(
LUN
)
SEMANAL
(
DOM
)
C
AN
C
ELAR
:
A
DD
/
DLT
ELEGIR 1- 8 :
ENTRAR
: SET
SAL
I
R
:
PROG
FE
I
N
I
C
PARADA
CA
VEL
7
2 : 00
P
3
:
20
P
02 SLP
--
--
:
--
--
:
--
--
--
--
--
:
--
--
:
--
--
--
--
--
:
--
--
:
--
--
--
Guía para rápida
consulta
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4767
68
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
1
Presione para seleccionar el ajuste
deseado.
Presione
SET
para ajustar.
Para volver a la pantalla normal,
Presione repetidamente
CLEAR
o
DISPLAY
.
Funcionnamiento del DVD utilizando
visualizaciones en pantalla
Presione
DISPLAY
en el modo reproducción
o parada para visualizar las visualizaciones en
pantalla.
Cada vez que se presione
DISPLAY
,la
visualización en pantalla cambia como se
muestra a continuación.
2
3
Presione (o ) para seleccionar el ítem
deseado.
Presione
SET
para ajustar.
Spanish Quick Use Guide/ Guía para rápida consulta
1
Para buscar una escena particular
Búsqueda hacia adelante
Presione
FF/SLOW+
en el modo de reproducción.
Búsqueda hacia atrás
Presione
REW/SLOW-
en el modo de reproducción.
(Para liberar, presione
PLAY
)
Para saltar un capítulo o una pista
Salto hacia adelante
Presione
SKIP
l en el modo de reproducción.
Un capítulo (Vídeo DVD) o una pista (Audio
DVD/Vídeo CD/CD) se salta cada ves que se
oprime la tecla.
Salto hacia atrás
Presione l
SKIP
en el modo de reproducción.
Para ver una imagen fija
Presione
PAUSE/STILL
durante la reproducción.
(Para liberar, presione
PLAY
)
Para ver imágenes cuadro a cuadro
(DVD/Vídeo CD)
Presione
PAUSE/STILL
en el modo de imagen fija.
La imagen avanza un cuadro cada vez que
presiona la tecla. (Para volver a la
reproducción normal, presione
PLAY
)
Para ver en cámara lenta (DVD/Vídeo CD)
Presione
FF/SLOW+
o
REW/SLOW-
en el modo
de imagen fija.
(Para liberar, presione
PLAY
)
3
4
5
6
Operaciones básicas del DVD
7
2
Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]
Presione
POWER
en el control remoto o el
aparato.
Presione
DVD
para seleccionar el modo DVD.
1) Presione
OPEN/CLOSE
.
2) Ponga un disco en la bandeja de disco.
Sujete el disco sin tocar ninguna de sus
superficies, póngalo con el lado donde esté
impreso el título hacia arriba, alinéelo con las
guías y póngalo en su posición apropiada.
Disco de 3 (8 cm) / Disco de 5 (12 cm)
Presione
PLAY
para iniciar la reproducción.
La bandeja del disco se cierra
automáticamente.
Si está usando un DVD interactivo (Interactive
DVD) o un Vídeo CD con contol de
reproducción (playback control) y aparece un
menú de títulos (TITLE MENU) en la pantalla,
siga al paso 5.
Presione o las teclas numéricas para
seleccionar el artículo deseado.
Presione
SET
o
PLAY
para la reproducción.
Si usa las teclas numéricas, la
reproducción comienza automáticamente.
Presione
STOP
para parar la reproducción.
Presione
OPEN/CLOSE
para expulsar el disco.
Cuando se presiona DISPLAY, la visualización en
pantalla muestra la información del disco (título / capítulo
/ número de lista, tiempo transcurrido de reproducción,
audio / idioma del subtítulo, y ángulo) e información
(repetir la reproducción, modo reproducción, Karaoke
vocal encendido / apagado, etc.).
Información seleccionada del disco
Información seleccionada del DECK
Pantalla normal
<Ejemplo (Vídeo DVD)>
<Ejemplo (Vídeo CD)>
GRUPO
: 1 DVD-AUDIO
P I STA
: 1 00:12:34
ELEGIR:
FIJAR : SET
TERMINAR
:DISPLAY
GRUPO
: 1 DVD-AUDIO
P I STA
: 1 00:12:34
ENTRAR: 0
-
9
FIJAR : SET
TERMINAR
:DISPLAY
<Ejemplo (Audio DVD)>
ELEGIR:
FIJAR : SET SIGUIENTE: DISPLAY
TITULO : 12 DVD
CAPITULO:11 00:12:34
ELEGIR:
FIJAR : SET SIGUIENTE: DISPLAY
TITULO : 12 DVD
CAPITULO: 24 00:12:34
PISTA : 12 VIDEO CD
PBC : INACTIVO 00:12: 34
FIJAR : SET SIGUIENTE: DISPLAY
PISTA : 17 VIDEO CD
PBC : INACTIVO 00:12: 34
FIJAR : SET SIGUIENTE: DISPLAY
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4768
69
1
Cambio del idioma de subtítulos
[Vídeo DVD solamente]
EI idioma de los subtítulos seleccionado al hacer las
fijaciones iniciales se puede cambiar por otro idioma
diferente, si éste se encuentra disponible.
Presione
SUBTITLE
durante
la reproducción.
Cuando no haya subtítulos
grabados, se visualizará - en
lugar del número de idioma.
Presione para
seleccionar el idioma deseado.
Presione para
seleccionar ACTIVO o
INACTIVO.
Selección de IDIOMAS DEL
DISCO [DVD solamente]
Presione para seleccionar el artículo deseado.
Presione
SET
.
4
1
2
3
IDIOMAS DEL DISCO
Todos los idiomas ofrecidos en el disco pueden ser
ajustados. Si el idioma ajustado no es ofrecido en el
disco, se seleccionará el idioma original del disco.
SALIDA DE AUDIO
Puede usted ajustar la salida audio procedente del
terminal de salida audio digital.
DETENER RASTREO
Para seleccionar CAMPO o CUADRO fijo para prevenir
inestabilidad o para permitir ver textos pequeños o
patrones finos claramente en el modo de imagen fija.
TV PREFERENCIA
Para seleccionar cuando el material del vídeo es para
pantalla ancha y se quiere reproducir en el estilo
Pan&Scan, en el estilo Letterbox o en el estilo 16:9 en
la pantalla.
5
Volver a visualizar el menú de DVD para
continuar el ajuste.
Presione
ACTION
y pase al paso 3 para ajustar otro
ajuste o, para salir, presione
ACTION
tres veces.
Presione DVD para seleccionar el modo DVD.
Presione ACTION en el modo de parada para
visualizar MENU.
Presione para seleccionar el artículo deseado.
Presione
SET
.
Seleccione AUDIO
(Fijación de fábrica : inglés)
Inglés / Español / Francés / Japonesa :
Original : Se seleccionará el idioma
original de cada disco.
OTRO
✱✱✱✱
:Se puede seleccionar el otro
idioma.
Seleccione SUBTITULO
AUTO : Se seleccionará el mismo que fue
seleccionado en la preparación de
AUDIO. (Fijación de fábrica)
Si el idioma seleccionado en la preparación
de AUDIO se utiliza durante la
reproducción, los subtítulos no aparecerán.
Si se utiliza otro idioma durante la
reproducción, los subtítulos aparecerán en el
idioma seleccionado en la preparación de
AUDIO
Inglés / Español / Francés / Japonesa :
OTRO
✱✱✱✱
:Se puede seleccionar el otro
idioma.
Seleccione MENU
(Fijación de fábrica : inglés)
Inglés / Español / Francés / Japonesa :
OTRO
✱✱✱✱
:Se puede seleccionar el otro
idioma.
Fijaciones iniciales
2
1
Cambio del idioma de la pista
de sonido [DVD solamente]
EI idioma de la pista de sonido seleccionado al hacer
las fijaciones iniciales se puede cambiar por otro
idioma diferente, si éste se encuentra disponible.
Presione
AUDIO
durante la reproducción
para visualizar
SONIDO en la pantalla.
2
Presione para
seleccionar idioma.
1
Visión desde otro ángulo
[DVD solamente]
Algunos discos DVD tienen escenas que han sido
filmadas simultáneamente desde ángulos diferentes.
Con estos discos, la misma escena podrá verse desde
cada uno de estos ángulos diferentes utilizando el botón
ANGLE.
Presione
ANGLE
durante la
reproducción para visualizar
la selección del ángulo.
2
Presione para
seleccionar el ángulo
deseado.
Selección de vocal para los
discos de Karaoke [DVD/Vídeo CD]
Presione
AUDIO
durante la reproducción
para visualizar la pantalla AUDIO.
Presione (o )
para seleccionar el ajuste
deseado.
Presione (o ) para
ajustar. (DVD solamente)
1
2
Guía para rápida
consulta
ELEGIR :
ACTIVO / INACTIVO :
TERMINAR : SUB TITLE
ELEGIR :
ACTIVO / INACTIVO :
TERMINAR : SUB TITLE
ANGULO
: 1
ELEGIR :
ANGULO
: 2
ELEGIR :
ELEG
I
R:
TERMI
NAR : AUDIO
ELEG
I
R:
TERMI
NAR : AUDIO
ELEG
I
R:
TERMI
NAR : AUDIO
DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF
DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF
Video CD LR L R
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4769
70
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Algunos discos con películas, vienen con dos o más
títulos. Por ejemplo, si el disco tiene un menú de
títulos grabados, el botón TITLE podrá utilizarse
para seleccionar el título de la película.
Presione
TITLE
durante la reproducción.
Ahora se visualiza una lista de los títulos del
disco.
Utilización de un menú de títulos
[DVD solamente]
T
I
TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
Presione o las
teclas de números para
seleccionar el título
deseado.
Presione
SET
para elegir.
1
Algunos discos DVD ofrecen un menú especial.
Este menú incluye guías para contenidos únicos,
audio, subtitulos, idiomas, etc. Aunque los
contenidos y las operaciones se cambian, los
siguientes son unos pasos básicos para el uso del
menú.
Presione
MENU
durante la reproducción.
El menú de DVD introducido en el disco se
visualiza ahora.
Dogs
of the world
2
Presione o las
teclas de números
para
seleccionar el ítem deseado.
Presione
SET
para elegir.
Ampliación de la imagen [Vídeo DVD solamente]
Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la
relación de zoom usando el botón ZOOM.
Presione
ZOOM
repetidamente para cambiar el
tamaño de la imagen como se indica a continuación:
2da
3da
Use los botones , , y para desplazar
la posición hacia arriba, hacia abajo, hacia la
izquierda o hacia la derecha.
1
2
Utilización de un menú de DVD
[DVD solamente]
DVD MENU
3 . ANGLE
1 . SUBT
I
TLE
2 . AUD
I
O
Spanish Quick Use Guide/ Guía para rápida consulta
Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]
REPROD
MODE DE REPRODUCCION:
NORMAL
00
:
00
:
00
ROOT
. .
VA
VA
END
_
W
ALTZ
TECHNO
DD
_
CUB I C
POPS
N
O
CTURNE
J
AZZ
N
O
RN
Presione
POWER
en el control remoto o DECK.
Presione
OPEN/CLOSE
y a continuacion
coloque un disco MP3/WMA/JPEG en la bandeja
de discos.
Presione
OPEN/CLOSE
para cerrarla.
Puede utilizar esta unidad para reproducir audio de
formato MP3/WMA/JPEG, grabado para uso personal
con una computadora, etc., en un CD-ROM o CD-RW.
La ejecución no podrá realizarse en algunos casos,
debido a las condiciones de la grabación.
Se visualizará el MENU MP3/WMA/JPEG y la
ejecución se iniciará automáticamente. (Se
visualizará el directorio del CD.)
Estado de la
función
Contador
MODO DE REPRODUCCIÓN
Area de las
carpetas
Area de
archivos
Carpeta
principal
(La carpeta
visualizada
actualmente se
volverá verde)
(El archivo/ la
carpeta se
visualiza con
un cursor.)
:Archivo MP3 :Archivo WMA :Archivo JPEG
:Carpeta :Carpeta principal
4
Ejecución MP3/WMA/JPEG (Durante el modo STOP)
Presione para seleccionar un archivo MP3/WMA
(
/
) o un archivo JPEG ( ), y presione
SET
o
PLAY
.
MP3/WMA
Búsqueda hacia adelante/hacia atrás
Presione
FF/SLOW+
o
REW/SLOW-
durante la ejecución.
Salto de pista hacia adelante/hacia atrás
Presione
SKIP
| o |
SKIP
durante la ejecución.
JPEG
Búsqueda siguiente/anterior
Presione
SKIP
| o |
SKIP
.
Inicie la muestra-diapositiva
Presione
FF/SLOW+
o
REW/SLOW-
.
Ampliar una imagen Presione
ZOOM
.
Girar una imagen Presione
ANGLE
.
Presione
STOP
para detener la operación descrita arriba.
Seleccione MODO DE REPRODUCCION
(Durante el modo STOP)
Presione para mover el cursor a MODO DE
REPRODUCCION, y Presione
para seleccionar el
MODO DE REPRODUCCIÓN deseado.
[MODO DE REPRODUCCIÓN]
NORMAL: Todos los archivos se reproducen sólo una vez
REPETICION DE UNA MUSIC:
El archivo seleccionado se reproduce repetidamente.
REPETICION DE UN ARCHIVO:
Los archivos que se encuentran en la carpeta
seleccionada se reproducen repetidamente.
REPETICION DEL DISCO:
Todos los archivos se reproducen repetidamente.
1
2
3
Funcionamiento de la ejecución de MP3/WMA/JPEG
5
Presione
ACTION
para regresar al DVD MENU
PRINCIPAL.
<ejemplo>
<ejemplo>
<ejemplo>
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4770
71
ELEG
I
R : F
I
JAR: SET
SAL
I
R : ACTION PAG
I
NA: SK
I
P
+/
-
SINGLE
SLIDE
1
/
3
Ejecución de JPEG con Tarjeta SD
Los datos de imagen fija (JPEG) creados mediante la
cámara digital, la cámara de video digital o el PC se
pueden ejecutar utilizando una tarjeta SD/MMC.
Inserte la tarjeta SD <El modo VCR y la tarjeta SD
ya han sido insertados.>
Cambia la pantalla
MENU SD
automaticamente.
o
Presione ACTION.
Presione para
seleccionar SD CARD
REPRODUCCION,
y presione SET para
visualizar la pantalla del
MENU SD.
Durante la grabación el
menú de arriba no se
visualiza. Para visualizar el
menú SD, reinserte la
tarjeta SD.
Nota
ELEGIR
:
SALIR
: ACTION
FIJAR : SET
MENU
PREPARAR VCR
FIJAR RELOJ
FIJAR CANAL
SD CARD REPRODUCCION
LANGUE/LANGUAGE:ESPAÑOL
CANAL DE SALIDA : 3
Configuración de los altavoces
1
Presione para
seleccionar AJUSTE DE
ALTAVOCES, y
Presione
SET
para
visualizar la pantalla
AJUSTE DE ALTAVOCES.
3
AJUSTE DE ALTAVOCES
ELEG
I
R:
F
I
JAR : SET
TERM
I
NAR : ACTION
SAL
I
DA PARA ALTAVOCES :
MULT
I
-
CANALES
TAMAÑO DEL ALTAVOZ
BALANCE DE SAL
I
DA
T
I EMPO ATRAZADO
Presione para seleccionar, y presione
SET
para fijar.
SALIDA PARA ALTAVOCES
Fije el número de altavoces conectados al DECK.
MULTI-CANALES (Predeterminado en fábrica)
Cuando están conectados 3 o más altavoces.
2 CANALES
Cuando están conectados 2 altavoces.
TAMAÑO DEL ALTAVOZ
Se determinan las propiedades de frecuencia del
altavoz y la existencia de los altavoces.
FRENTE (GRANDE [predeterminado en fábrica]/
PEQUEÑO)
CENTRO (GRANDE [predeterminado en fábrica]/
PEQUEÑO/NINGUNO)
ENVOLVENTE (GRANDE [predeterminado en
fábrica]/PEQUEÑO/NINGUNO)
SUBWOOFER (ENCENDIDO [predeterminado en
fábrica]/APAGADO)
BALANCE DE SALIDA
Ajuste la salida de nivel de volumen para los altavoces.
CENTRO, ENVOLVENTE(DER)/(IZQ), SUBWOOFER
-6db ~ +6db (0db: predeterminado en fábrica)
SEÑAL PRUEBA
El sonido de prueba es la salida en sentido de las
manecillas del reloj.
TIEMPO ATRAZADO
Configurar el tiempo atrazado. Da a la salida de
sonido un efecto retrasado que le ofrece la ilusión de
encontrarse en la posición de escucha ideal.
4
Presione
ACTION
tres o cuatro veces
para salir.
5
1
VISUALIZACION DEL MENU SD.
2
AREA DEL
INDICE
Este área se
utiliza para
visualizar los
archivos
almacenados
en la tarjeta
SD.
EJECUCION
UNICA
MUESTRA-
DIAPOSITIVA
SINGLE (EJECUCIÓN ÚNICA)
Este modo permite ampliar y ejecutar una sola imagen
seleccionada del índice de visualización. Además, este
modo permite aplicar a la imagen varias funciones,
incluidas el zoom, la rotación e información de la imagen.
Ampliar una imagen (ZOOM) Presione ZOOM
PARA GIRAR Presione ANGLE
Iniciar la muestra-diapositiva
Presione PLAY (vea debajo)
Visualizar la pantalla de información del archivo
Presione DISPLAY.
SLIDE SHOW (MUESTRA DIAPOSITIVA)
Este modo permite que se visualice una secuencia de
imágenes, una detrás de la otra. Además, también
permite seleccionar imágenes para visualizarlas, y la
selección de ajuste para los efectos de transición de la
pantalla y la velocidad de transición.
Presione para seleccionar SINGLE o
SLIDE, y presione SET.
Presione
para seleccionar (vea a la
derecha), y presione SET
repetidamente.
ELEG
I
R: F
I
JAR: SET
TERMINAR : ACTION
COM
I
ENZO
VELOC
I
DAD : ALTA 2S
TRANSICION : NORMAL
[VELOCIDAD]
Fije el tiempo de transición
ALTA(2 seg)/MEDIANA(5 seg)/BAJA(10 seg)
[TRANSICION]
NORMAL: Para que las imágenes pasen una
a una.
DESLIZAR: Para que las imágenes pasen de
arriba abajo.
DIVICIONES: Para que las imágenes pasen
empezando por el centro y
partiéndose a la izquierda y la
derecha.
COLUMNAS: Para que las imágenes pasen en
una serie de formas tipo bandas
asemejándose a las persianas de
una ventana.
presione ACTION para salir de cada
modo.
3
2
Presione
POWER
en el control remoto o el
aparato.
Presione
DVD
para seleccionar el modo DVD.
Guía para rápida
consulta
2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4771
Printed in Indonesia
LSQT0676A
S0303-2073
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company (PSC),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
P
A ACTION button ...................................................................... 8, 18
Accessories ............................................................................... 4
ADD/DELETE button (Add or Delete a Channel) .................. 8, 19
Audio Broadcast types (Stereo/SAP/Mono) .............................. 26
Audio Mode (Playback, Recording) .......................................... 27
Auto Operation Functions .......................................................... 31
Auto Shut-Off .............................................................................33
B Batteries ..................................................................................... 4
C Channel (“SET UP CHANNEL”) ..............................................18
Channel Up/Down, Tracking/V-Lock Button ............................ 4, 8
Clock (“SET CLOCK”) .............................................................18
Commercial Skip......................................................................31
Connections ..................................................................... 12 ~ 15
Copy Your Tapes (Dubbing) ..................................................... 35
COUNTER RESET button .................................................... 8, 32
Customer Services Directory ...................................................65
D DISPLAY button .................................................................... 8, 11
DSS/CABLE mode button ...................................................... 8, 28
DST (Daylight Saving Time) ....................................................19
E EJECT button ........................................................................ 8, 20
ENTER button (For tuning TV Channel) ............................... 8, 28
F FAST FORWARD/SEARCH button ..................................... 8, 20
H Head Cleaning ............................................................................ 4
I Index Search .............................................................................30
Indicator (Multi Function Display) .............................................11
Initial Setup (Ready to Play) ................................................ 16, 17
INPUT button ........................................................................ 8, 35
L Limited Warranty ............................................................... 64, 65
Location of Controls (Remote, DECK) ............................... 8 ~ 10
M Multi-Brand Control ............................................................ 28, 29
O On-Screen Displays (VCR) ......................................................11
One Touch Recording ............................................................... 21
DECK & VCR
P PAUSE/STILL button (Still Picture) ....................................... 8, 20
PLAY button (Playback a Tape) ............................................. 8, 20
POWER button ........................................................................... 8
PROG button (PROGRAM) .................................................. 8, 24
Program Clear, Review, Replace ............................................. 25
Program End Search................................................................. 30
Q Quality Picture ............................................................................. 4
R REC button (Record on a Tape) ............................................ 8, 21
Record Tab ................................................................................ 6
Remote Sensor .......................................................................... 9
Remote Warning ...................................................................... 34
Repeat Play ...............................................................................32
Reset All Memory Functions ..................................................... 9
REWIND/SEARCH button .................................................... 8, 20
S SAP/Hi-Fi .................................................................................27
SEARCH (Index and Program End Search).............................. 30
SLOW+/SLOW- button (Slow Motion Picture) ..................... 8, 20
Spanish Quick Use Guide ................................................ 66 ~ 71
Specifications ............................................................................ 7
SPEED button ....................................................................... 8, 21
Still (Freeze) Picture ................................................................20
STOP button .......................................................................... 8, 20
T Tape Position, Tape Status .......................................................34
Timer Recording ......................................................................24
Trouble Shooting ................................................................. 62, 63
TV mode button ..................................................................... 8, 28
V VCR Lock .................................................................................33
VCR mode button.................................................................. 8, 28
VCR/TV button ...................................................................... 8, 21
VCR/TV Selector Feature ......................................................... 32
VOLUME +/- button (TV Volume) ......................................... 8, 28
W Warning and Instruction Displays ............................................. 61
Weak Signal Display................................................................. 33
Z ZERO SEARCH button ......................................................... 8, 32
INDEX
A ACTION button ...................................................................... 8, 53
ANGLE button (Multiple Angle Viewing) .................... 8, 37, 51, 59
AUDIO button (Audio Soundtrack Language) ........................ 8, 36
Audio Output (For Selecting Audio Output) ............................... 54
Auto-Power Off Function ...........................................................23
B Bonus Group (For DVD-Audio) ................................................. 41
C CLEAR button ................................................................. 8, 39, 52
Component Video Output .................................................... 10, 13
D Delay Time Setup .....................................................................56
Disc Languages ........................................................................ 53
Direct Navigator .......................................................................42
DISPLAY button (“On-Screen Display”) ............................... 8, 44
DTS ..........................................................................................14
DVD-Audio................................................................................41
DVD Lock Ratings .................................................................... 52
DVD Menu ................................................................................38
DVD mode button .................................................................. 8, 28
DVD-RAM ................................................................................42
F 5.1ch Analog Audio Output .................................................. 15, 51
Frame by Frame Picture ..........................................................23
Forward/Reverse Chapter/Track Skip ......................................23
Forward/Reverse Scene Search ...............................................23
J JPEG ................................................................................ 49 ~ 51
JPEG Playback (SD) ................................................................58
K Karaoke (Vocal Selection for Karaoke Discs) ...........................37
L Language Code List ...................................................................60
M MENU button (To display DVD Menu) ................................. 8, 38
MP3 ..........................................................................................49
Multiple Angle Viewing ............................................................. 37
Multi-channel speaker system ............................................ 15, 55
O OPEN/CLOSE button ............................................................ 8, 22
Optical Digital Audio Output ................................................ 10, 15
Output Balance Setup ................................................................56
DVD
P PAGE button (Still Image Skip) ............................................. 8, 41
PLAY button (Play a Disc) .................................................... 8, 22
Play List .................................................................................... 43
Program Play (For Video CD/ CD) ..........................................39
PROGRESSIVE button .............................................................. 9
Progressive Scan...................................................................... 10
R Random Play (For Video CD/ CD) ...........................................40
Repeat Play ......................................................................... 47, 48
Resume Function...................................................................... 23
RETURN button .................................................................... 8, 22
Rotation............................................................................... 51, 59
S SD Card.............................................................................. 58, 59
SEARCH button
(Forward/Reverse Scene Search) ...................................... 8, 23
SINGLE PLAY Mode ................................................................. 59
SKIP l or l button
(Forward/Reverse Chapter/Track) ..................................... 8, 23
Slide-show ..........................................................................50, 59
SLOW+/SLOW- button (Slow Motion Picture) ..................... 8, 23
Speaker Output Setup ................................................................55
Speaker Position ....................................................................... 57
Speaker Size Setup ...................................................................55
STILL button (Still Picture or Pause) ..................................... 8, 23
Still Mode (For selecting “FIELD” or “FRAME”) ......................57
STOP button .......................................................................... 8, 22
SUB TITLE button
(For selecting Subtitle Language) ........................................ 8, 36
S-Video Out ......................................................................... 10, 13
T Test Signal Setup ...................................................................... 57
TITLE button (Title Menu) ..................................................... 8, 38
TV Mode (For selecting the screen display style) ....................57
2-channel speaker system .................................................. 15, 55
V Video CD ..................................................................................23
VOLUME ADJUST button ..................................................... 8, 40
V.S.S. (Virtual Surround Sound) ........................................... 8, 23
W WMA .........................................................................................49
Z ZOOM button (Picture Zoom) .................................... 8, 37, 51, 59
D4763S P36-60 (030610 –§”Ô•Ï•X2nd).p65 2003/06/10, 18:5972
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Panasonic PVD4763S Instrucciones de operación

Categoría
Reproductores de DVD
Tipo
Instrucciones de operación

En otros idiomas