Panasonic PV 20D53 Manual de usuario

Advanced Operation

Initial Setup

DVD Operation

TV Operation

For Your Information

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

TV

/

DVD

Combination

Operating Instructions

Model No.

PV-20D53/PV-27D53

LSQT0669B

This operating instruction book is designed for use with models PV-20D53 and PV-27D53. Illustrations

in this manual show the PV-27D53. Fea tures may vary, so please read care ful ly.

• Initial Setup and Connection Procedures are on pages 10 to 11.

As an ENERGY STAR

®

Partner, Matsushita Electric Corporation

of America has determined that this product or product model

meets the ENERGY STAR

®

guidelines for energy efﬁ ciency.

Please read these instructions carefully before attempting to connect,

operate or adjust this product. Please save this manual.

Spanish Quick Use Guide is included.

(Guía para rápida consulta en español está incluida.)

MULTI FORMAT PLAYBACK

*Ability to play back may depend on recording conditions.

2

Important Safeguards and Pre cau tions

OUTDOOR ANTENNA INSTALLATION

USING THE UNIT

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from power source indicated on unit

or in this manual. If uncertain, have your Electric

Utility Service Company or Video Products Dealer

verify your home power source.

2 POWER CORD PLUG

For safety, this unit has a polarized type plug (one

wide blade), or a three-wire grounding type plug.

Always hold the plug ﬁ rmly and make sure your

hands are dry when plugging in or unplugging the AC

power cord.

Regularly remove dust, dirt, etc. on the plug.

POLARIZED PLUG CAUTION:

The plug ﬁ ts into outlet only one way. If it cannot be

fully inserted, try reversing it. If it still will not ﬁ t, have an

electrician install the proper wall outlet. Do not tamper

with the plug.

GROUNDING PLUG CAUTION:

The plug requires a three-hole grounding outlet.

If necessary, have an electrician install the proper

outlet. Do not tamper with the plug.

3 POWER CORD

To avoid unit malfunction, and to protect against

electrical shock, ﬁ re or personal injury:

- Keep power cord away from heating appliances and

walking trafﬁ c. Do not rest heavy objects on, or roll

such objects over the power cord.

- Do not tamper with the cord in any way.

- An extension cord should have the same type plug

(polarized or grounding) and must be securely

connected.

- Overloaded wall outlets or extension cords are ﬁ re

hazards.

- Frayed cords, damaged plugs, and damaged or

cracked wire insulation are hazardous and should

be replaced by a qualiﬁ ed electrician.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat

generated during operation. If blocked, heat

build-up may result in a ﬁ re hazard or heat

damage to discs.

For your protection:

a.Never cover ventilation slots while unit is ON,

or operate unit while placed on a bed, sofa, rug,

or other soft surface.

b.Avoid built-in installation, such as a book case

or rack, unless properly ventilated.

5 AVOID EXTREMELY HOT LOCATIONS OR

SUDDEN TEMPERATURE CHANGES

Do not place unit over or near a heater or radiator, in

direct sunlight, inside closed ve hi cles, in high

temperature [over 95 °F (35 °C)], or in over 75%

humidity. If unit is suddenly moved from a cold place

to a warm one, moisture may con dense in unit and on

the disc causing dam age. Never sub ject unit to

vibration, im pact, or place it so that the sur face is tilted

as in ter nal parts may be se ri ous ly dam aged.

6 TO AVOID PERSONAL INJURY

• Never place unit on support or

stand that is not ﬁ rm, level, and

adequately strong. The unit could

fall causing serious injury to a

child or adult and damage to the

unit.

• Move any appliance and cart

combination with care.

Quick stops, excessive force, and uneven surfaces

may cause objects to overturn.

• Carefully follow all operating instructions.

Before unit is brought out of storage or moved to a new location,

refer again to the INSTALLATION section of these safe guards.

1 KEEP UNIT WELL AWAY FROM WATER OR MOISTURE,

such as vases, sinks, tubs, etc.

2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT,

unplug unit and have it inspected by a qualiﬁ ed service

technician before use.

3 ELECTRICAL STORMS

During a lightning storm, or before leaving unit unused for

extended periods of time, disconnect all equipment from the

power source as well as the antenna and cable system.

4 WHEN UNIT IS PLUGGED IN

• DO NOT OPERATE IF:

- liquid has spilled into unit.

- unit was dropped or otherwise damaged.

- unit emits smoke, odours, or noises.

Immediately unplug unit, and have it inspected by a service

technician to avoid potential ﬁ re and shock hazards.

• Never drop or push any object through openings in unit.

Touching internal parts may cause electric shock or ﬁ re

hazard. Do not put any foreign object on the tray.

• Keep magnetic objects, such as speakers, away from unit to

avoid electrical interference.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to

avoid risk of ﬁ re, shock, or other hazards.

6 CLEANING UNIT

Unplug unit. Use a clean, dry, chemically untreated cloth to

gently remove dust or debris. DO NOT USE cleaning ﬂ uids,

aerosols, or forced air that could over-spray, or seep into unit

and cause electrical shock. Any substance, such as wax,

adhesive tape, etc. may mar the cabinet surface. Exposure to

greasy, humid, or dusty areas may adversely affect internal

parts.

READ AND RETAIN ALL SAFETY AND

OPERATING INSTRUCTIONS. HEED ALL

WARNINGS IN THE MANUAL AND ON UNIT

SERVICE

1 DO NOT SERVICE PRODUCT YOURSELF

If, after carefully following detailed operating in struc tions, the unit

does not operate properly, do not attempt to open or remove

covers, or make any adjustments not described in the manual.

Unplug unit and contact a qualiﬁ ed service tech ni cian.

2 REPLACEMENT OF PARTS

Make sure the service technician uses only parts speciﬁ ed by the

manufacturer, or have equal safety char ac ter is tics as original

parts. The use of unauthorized substitutes may result in ﬁ re,

electric shock, or other hazards.

3 SAFETY CHECK AFTER SERVICING

After unit is serviced or repaired, request that a thorough safety

check be done as described in the manufacturer’s service

literature to ensure video unit is in safe operating condition.

1 SAFE ANTENNA AND CABLE CONNECTION

An outside antenna or cable system must be properly grounded

to provide some protection against built up static charges and

voltage. Section 810 of the National Electrical Code,

ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical

Code) provides information regarding

proper grounding of the mast and

supporting structure, grounding of the

lead-in wire to an antenna discharge

unit, size of grounding conductors,

location of antenna discharge unit,

con nec tion to grounding electrodes,

and requirements for the grounding

electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES

OR CIRCUITS

Locate an outside antenna system well away from power lines

and electric light or power circuits so it will never touch these

power sources should it ever fall. When installing antenna,

absolutely never touch power lines, circuits or other power

sources as this could be fatal.

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC

- NATIONAL ELECTRICAL CODE

3

CAUTION:

LASER RADIATION

WHEN OPEN. DO NOT

STARE INTO BEAM.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.

HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD

CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE

SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT

PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY

AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE

UNIT YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

Safety Precautions/Mesures de sécurité

This symbol warns the user that uninsulated voltage within the

unit may have sufﬁ cient magnitude to cause electric shock.

Therefore, it is dangerous to make any kind of contact with any

inside part of this unit.

This symbol alerts the user that important literature concerning

the operation and main te nance of this unit has been included.

Therefore, it should be read carefully in order to avoid any

problems.

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead.

Disposal of these materials may be regulated in your community due to environmental considerations.

For disposal or recycling information please contact your local authorities, or the Electronics Industries

Alliance: <http://www.eiae.org.>

ATTENTION:

RAYONNEMENT LASER

EN CAS D’OUVERTURE.

NE PAS REGARDER

DANS LE FAISCEAU.

(Inside of product)

FCC NOTICE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when operated in a residential

environment. If this equipment does cause interference to radio or television reception, which can be

determined by turning the equipment off and on, use the equipment in another location and/or utilize an

electrical outlet different from that used by the receiver. If necessary, consult the dealer or an experienced

radio/TV technician for help. You may ﬁ nd the booklet, “Something About Interference” available from

FCC local regional ofﬁ ces helpful.

This television receiver provides display of television closed captioning.

Warning : To prevent ﬁ re or shock hazard, do not expose this equipment to rain or

mois ture.

Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert.

Avertissement : Aﬁ n de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer

cet appareil à la pluie ou à une humidité excessive.

Attention : Pour éviter les chocs électriques, introduire la lame la plus large de la ﬁ che dans

la borne correspondante de la prise et pousser jusqu’au fond.

FCC WARNING : Any unauthorized changes or modiﬁ cations to this equipment would void the

user’s authority to operate.

Region Management Information

This unit is designed and man u fac tured to respond to the

Region Management Information that is recorded on a DVD

disc. If the Region number described on the DVD disc does

not cor re spond to the Region number of this unit, this unit

cannot play this disc.

• The region number of this player is “1.”

• The player will play DVD-Video marked with labels containing “1”

or “ALL.”

1

Example:

4

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

4

Before Using

Congratulations

On your purchase of one of the most sophisticated

and reliable products on the market today. Used

properly, it will bring you and your family years of

enjoyment. Please ﬁ ll in the information below.

The serial number is on the tag located on the

back of your unit.

Date of Purchase

Dealer Purchased From

Dealer Address

Dealer Phone No.

Model No.

Serial No.

Accessories

Loading the Batteries

Batteries 2 “AA”

To order accessories,

call toll free

1-800-332-5368.

Features for a Quality Picture

Apparatus Claims of U.S. Patent Nos. 4,631,603,

4,577,216, 4,819,098, and 4,907,093, licensed

for limited viewing uses only.

This product incorporates copyright protection

technology that is protected by method claims of

certain U.S. Patents and other intellectual

property rights owned by Macrovision

Corporation and other rights owners. Use of this

copyright protection technology must be

authorized by Macrovision Corporation, and is

intended for home and other limited viewing

uses only unless otherwise authorized by

Macrovision Cor po ra tion. Reverse engineering

or dis as sem bly is prohibited.

Remote Control

LSSQ0373

PanaBlack™ Picture Tube (PV-27D53 only)

This unit uses a PanaBlack™ picture tube for better

color reproduction and picture contrast.

1) Open the cover.

3) Close the cover.

2) Insert batteries as

marked.

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

55

Initial Setup

Table of Contents

TV Operation

Advanced Operation

For Your Information

Initial Setup

Important Safeguards and Precautions ........................................2

Safety Precautions/Mesures de sécurité.......................................3

Before Using ....................................................................................4

Information (Unit, Disc)...................................................................6

Location of Controls .......................................................................8

Initial Setup (Ready to Play) .........................................................10

Reset Language, Channels, Clock, Time Zone Adjust...............12

Audio Connections........................................................................14

Basic DVD Operation ....................................................................16

TV Operation..................................................................................18

MTS Broadcast/TV Stereo System...............................................19

Closed Caption System ................................................................20

TV Timer Features .........................................................................22

On-Screen Display (OSD) .............................................................23

FM Radio ........................................................................................24

Special Features............................................................................26

V-Chip Control Feature ................................................................28

Video/Audio Menu .........................................................................32

Video/Audio Adjustment...............................................................33

Disc Operation ..............................................................................34

DVD Operation using On-Screen Displays .................................39

MP3/WMA/JPEG Playback Operation..........................................42

DVD Lock Feature..........................................................................45

Settings for DVD Operation..........................................................46

Language Code List ......................................................................49

Before Requesting Service...........................................................50

Warning and Instruction Displays ...............................................52

Spanish Quick Use Guide/Guía para rápida consulta................53

Limited Warranty ...........................................................................60

Customer Services Directory .......................................................61

Index ...............................................................................................62

DVD

TV

DVD

TV

DVD Operation

6

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

6

Information (Unit, Disc)

Speciﬁ cations

• Designs and spec i ﬁ ca tions are sub ject to change

without no tice.

Note

Display

Picture Tube

20 inch measured diagonal 90°

deﬂ ection Picture Tube (PV-20D53)

27 inch measured diagonal 100°

deﬂ ection Picture Tube (PV-27D53)

Tuner

Broad cast Channels VHF 2 ~ 13, UHF 14 ~ 69

CA BLE Channels

Midband A through I (14 ~ 22)

Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64)

Lowband A-5 ~ A-1 (95 ~ 99)

Special CABLE channel 5A (01)

Ultraband 65 ~ 94, 100 ~ 125

FM Radio

Band Range 87.5 MHz ~ 108.1 MHz

General

Power Source 120 V AC, 60 Hz

Power

Consumption

Power

On

Approx. 117 W (PV-20D53)

Approx. 150 W (PV-27D53)

Power

Off

Approx. 3.5 W

Television System EIA Standard NTSC color

Speak er

2 pieces 3 W (PV-20D53)

2 pieces 5 W (PV-27D53)

Op er at ing

Temperature

5 °C ~ 35 °C (41 °F ~ 95 °F)

Op er at ing Humidity 10 % ~ 75 %

Weight

23 k

g

(50.6 lbs.) (PV-20D53)

39 k

g

(85.8 lbs.) (PV-27D53)

Di men sions

(W x H x D)

515 mm (20-5/16

″

) x 505 mm (19-7/8

″

) x

474 mm (18-11/16

″

) (PV-20D53)

688 mm (27-1/16″) x 653 mm (25-11/16″) x

550 mm (21-11/16″) (PV-27D53)

Discs played

DVD disc

(DVD-Video, DVD-R)

12 cm (5

″

) single-sided, single-layer

12 cm (5

″

) single-sided, double-layer

12 cm (5

″

) double-sided, double-layer

(one layer per side)

8 cm (3

″

) single-sided, single-layer

8 cm (3

″

) single-sided, double-layer

8 cm (3

″

) double-sided, double-layer

(one layer per side)

Compact disc

(CD-DA, VIDEO CD,

CD-R, CD-RW)

5

″

(12 cm) disc

3

″

(8 cm) disc

MP3, WMA, JPEG

Digital audio output

Optical digital output Optical connector

Pickup

Wavelength

655 nm (DVD)

790 nm (Video CD/CD)

Laser power: CLASS II

Discs which cannot be played with this unit

• CD-ROM

• CDV

• CVD

• CD-G

• CD-TEXT

• SACD

• Photo-CD

• DVD with Region No.

other than “1” or

“ALL”

• DVD of PAL system

• DVD-ROM

• DVD-AUDIO

• DVD-RW

• DVD+RW

Disc type Disc Logo

Disc formats

supported by

this unit

DVD-Video

• DVD-Video

format

DVD-R

• DVD-Video

formatted discs

(ﬁ nalized*)

It may not be

possible to play

these discs in all

cases due to the

type of disc or

condition of the

recording.

Video CD

• Video-CD format

CD-DA

• CD-DA format

CD-R

• CD-DA format

• Video-CD format

• MP3/WMA/JPEG

ﬁ le and ﬁ nalized*.

CD-RW

Discs that can be played

• Discs played 8 cm (3

″

) or 12 cm (5

″

)

• * A process that allows play on compatible equipment.

77

Initial Setup

Handling precautions

• Sticking a label on the disc may impair DVD-R

playback.

• Do not attach sticker to discs. (Do not use discs with

exposed adhesive from tape or left over peeled-off

stickers.)

• Only hold disc by edges as

shown. Fingerprints, dirt, and

scratches can cause skipping

and distortion.

• Do not write on label side of

disc.

• Never use record cleaning

sprays, benzine, thinner,

static electricity prevention

liquids, or any other

solvent.

• Be careful not to drop or bend disc.

• Do not place more than 1 disc on disc tray.

• Do not try to close disc

tray when disc is not

properly placed.

• Always store discs in

their proper cases

when not in use.

Angle

Some DVD discs feature scenes si mul ta ne ous ly

shot from different angles. The ANGLE button can

be used to view the scene from different angles.

(ANGLE Indicator lights up on the unit when a

scene recorded at different angles is detected.)

Chapter Number

Titles are subdivided into numbered sections. You can

quickly search for a favorite scene using these

numbers.

DVD

A high-density optical disc on which high-quality

pictures and sound have been digitally recorded.

DVD incorporates new video compression technology

(MPEG II) and high-density recording technology

which allow entire movies to be recorded with

incredible playback quality.

Playback Control

With Video CD (version 2.0), scenes or in for ma tion

may be selected for viewing or listening from an

interactive menu that appears on the TV screen.

Subtitles

Written dialogue which appears at the bottom of the

screen.

Time Number

The elapsed play time from the start of a disc or

title. Use to quickly ﬁ nd scenes.

(May not work with

some discs.)

Title Number

For DVD discs with two or more titles, the title is

numbered as title 1, title 2, etc.

Track Number

Numbers assigned to tracks on Video CDs and

CDs to allow speciﬁ c tracks to be quickly located.

Video CD

CD containing picture and sound with same quality

level as video tape. This unit also supports Video

CDs with playback control (version 2.0).

Deﬁ nition of Terms

If the disc cannot be removed,

First unplug unit.

Then, prepare a rigid wire (e.g. an

extended paper clip, etc.) and,

applying moderate force, insert it

straight into the hole at the base of

the tray. The tray will eject a little.

Now, pull the tray all the way out

and remove the disc.

If disc is brought from a cold to a warm

environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth

before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Disc Handling

Disc tray

Disc

To clean disc surface

With a soft, damp (water only) cloth, gently wipe

from the center hole to the outer edge as shown

below. (Wiping in a circular pattern will scratch the

surface.)

8

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

8

Location of Controls

Remote Control Buttons

OPEN/CLOSE

Opens or closes the disc tray.

POWER

Turns the unit on or off.

DISPLAY

Displays the TV status and

clock. In DVD mode, displays

disc and unit information.

RAPID TUNE

Displays the last channel

you were watching.

MUTE

Mutes the sound instantly.

TIMER

Sets ON TIMER or SLEEP TIMER.

ACTION

Displays Main Menu.

CHANNEL UP/DOWN

Selects a channel.

SKIP-

|

Skips back one chapter or track.

Goes to previous menu screen.

STOP

Stops playback.

PAUSE

Pauses picture in Play mode and

frame advance picture in Still mode.

SEARCH /SLOW

Decreases slow motion speed in Still

mode. Reverses raid scene search in

Play mode.

AUDIO

Selects the desired audio mode.

ANGLE

Selects the desired angle in DVD mode.

RETURN

Returns to Menu screen.

FM/TV

Sets to TV mode.

Receives FM radio signal.

DVD

Sets to DVD mode.

NUMBER Keys

Selects a channel directly.

ADD/DELETE/CLEAR

Adds or deletes a channel.

Cancels an item on the screen.

MENU

Displays DVD menu.

SELECT

Controls navigation around

on-screen menu.

SET

Sets a selected menu.

VOLUME UP/DOWN

Adjusts volume.

PLAY

Begins playback.

SKIP+

|

Skips one chapter or track. Goes

to next menu screen.

TITLE

Selects the desired title by

number on some DVDs.

SEARCH/SLOW

Increases slow motion speed in

Still mode. Forwards raid scene

search in Play mode.

SURROUND/V.S.S.

Creates a deeper, 3-D sound

effect.

SUB TITLE

Selects a different subtitle

language.

ZOOM

Enlarges speciﬁ c portions of

picture.

99

Initial Setup

Rear View of the unit

Front View of the unit and Indicators

Phones Jack

Connect an earphone

or headphones.

Audio/Video Input Connector 2

(LINE 2)

Connect from other component.

Disc Tray

AC Power Plug

When plugged into

an AC outlet, this

unit consumes

3.5 W of electric

power in OFF

condition.

VHF/UHF Antenna Input Terminal

In from your Antenna or Cable.

Audio/Video Input Connector 1

(LINE 1)

Connect from other component.

Optical digital audio output connector

Connect to Dolby Digital decoder or dts

decoder. For details, see page 14.

Audio Output Connector (L/R)

Connect to other component.

Remote Sensor

ANGLE Indicator

Lights when a scene

recorded at a different

angles is detected.

ON TIMER Indicator

Lights when the On-Timer

is set.

SLEEPTIMER Indicator

Lights when the

Sleep-Timer is set.

POWER

Turns the unit on or off.

CHANNEL UP/DOWN

Selects a channel.

VOLUME UP/DOWN

Adjusts volume.

STOP

Stops playback.

SKIP

|

Skips back one chapter or

track. Goes to previous menu

screen.

PLAY

Begins playback.

SKIP

|

Skips one chapter or track.

Goes to next menu screen.

PAUSE

Pauses picture in Play mode

and frame advance picture in

Still mode.

OPEN/CLOSE

Opens or closes the disc tray.

10

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

10

Initial Setup (Ready to Play)

2

/

6

/

2003

THU

12

:

00

P

M

DST

:

O

N

A

UTO

C

L

OCK SET

CO

M

P

L

ETED

SETT

I

N

G

:

CH

1

0

PLEASE

SET

CLOCK BY

P

R

ESS

I

NG

ACT

I

ON

KEY

A

UTO

C

L

OCK SET

I S I NCO

M

P

L

ETE

Plug the unit power cord into an AC

wall outlet.

1

3

2

• If you use a cable box, turn it on and set it to the

Public Broadcasting Service (PBS) channel in your

time zone. If you use a DSS receiver, it must be

turned off.

Initial Setup (Ready to Play)

Please make all cable or antenna connections before powering on.

Press POWER* on the remote or unit.

The unit comes on and auto channel

and clock set starts.

Settings are made automatically. When

setup is done, this screen appears.

If AUTO CLOCK SET IS INCOMPLETE

screen appears, set the clock using MANUAL

CLOCK SET procedure on next page.

• Function buttons are inoperative during Initial Setup.

• Depending on conditions, Auto Clock Set may take

longer than 30 minutes. If so, press STOP to stop

setup and perform settings manually. (See page

12-13.)

Connections

For ANT./Cable

Connect the cable from Antenna/Cable to

the VHF/UHF terminal on the unit.

For DSS/Cable Box

Connect the OUT jack on your cable box

to the VHF/UHF terminal on the unit with

a RF cable.

Overtightening “Nut type” RF coaxial cables

may damage jacks. Finger tighten only.

WARNING

Notes

PROCEEDING

AUTO CLOCK SET

CANCEL : PRESS STOP KEY

CH AUTO SET PROCEEDING

IN from

ANT./CABLE

VHF/UHF

IN

from

ANT./CABL

E

Cable TV

Converter Box

VHF/UHF

1111

Initial Setup

Note to CABLE system installer:

This re mind er is pro vid ed to call the CABLE

(Cable TV) System Installers at ten tion to Article

820-40 of the NEC that pro vides guide lines for

proper grounding and, in par tic u lar, speciﬁ es

that the cable ground shall be con nect ed to the

ground ing system of the build ing, as close to

the point of cable entry as practical.

THU

SET

:

SET

SE

L

E

C

T

:

END

:

ACT

I

O

N

SET

C

L

OC

K

DST

:

O

N

SE

L

E

C

T

M

O

N

TH

*

Important:

If a remote control button does not work when pressed, press the FM/TV button on

the remote and try the button again.

Manual Clock Set

If AUTO CLOCK SET was incomplete, manually

set the clock as follows.

Press ACTION on

the remote to

display SET

CLOCK Menu

screen.

1

Press to

select the month

and press SET to

set. In the same

manner, select

and set the date,

year, time, and

DST (Daylight

Saving Time).

2

Press ACTION twice to start CLOCK and

exit.

3

Reset all unit Memory Functions

When moving unit to a new location, or if a mistake

was made in the Initial Setup section.

Turn the unit Power

on.

1

Press and hold both PLAY and on the unit

for more than 5 seconds.

• The power will shut off.

2

Perform “Initial Setup” on page 10.

3

Unit auto adjusts clock for DST (Daylight Saving

Time.)

DST (Daylight Saving Time)

• If your area does not observe Daylight Saving Time,

select DST : OFF (see “Clock” on pages 12 and 13).

■ Spring (First Sunday in April)

DST: ON

➞

Sets clock ahead one hour.

■ Autumn (Last Sunday in October)

DST: OFF

➞

Turns clock back one hour.

STOP

POWER

ACTION

POWER

SELECT

SET

12

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

12

Reset Language, Channels, Clock,

3)Press to select

“MANUAL,” then

press SET.

(For Auto Clock Set,

select “AUTO CLOCK

SET,” and press SET.)

3) Press to select

“ANTENNA,” then

press SET to set

your antenna system

(“TV” or “CABLE”).

4) Press to select

“AUTO SET,” then

press SET.

• After Channel Auto Set is

ﬁ nished, Clock Auto Set will be

performed.

(If clock is set manually, Clock

Auto Set will not be performed.)

(“TIME ZONE ADJUST”

appears only when

auto clock is set.)

1) Press to

select language

icon.

2) Press SET

repeatedly.

■ Language ■ Channels ■ Clock

Press ACTION*

to display MAIN MENU.

3) Press ACTION

to exit.

1) Press to

select “CH.”

2) Press SET.

1) Press to

select “CLOCK.”

2) Press SET.

1

2

For English

For Spanish

For French

<Example MANUAL

CLOCK SET screen>

Continued on

the next page.

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

MENU PR

I

NCIPAL

DVD

BLOQUEO

CANAL

RELOJTV

ID

I

OMA

TERM

I

NAR :

ACT

I

O

N

ELEG

I

R

:

F

I

JAR

:

SET

5

3

1

HOLA

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

HELLO

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END

:

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

ANT

ENN

A

:

C

ABLE

A

U

T

O

S

E

T

W

EAK

S

I

GNAL

D

I

SPLAY

:

OFF

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

SET UP

CH

A

NNE

L

AUT

O

C

L

OC

K SET

M

A

NU

AL

T

I

M

E

ZO

N

E

A

D

JUS

T

:

0

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

SET

C

L

OC

K

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END

:

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

MENU

DVD

BLOCAGE

CANAL

HORLOGETELE

LANGUE

FIN :

ACT

I

O

N

SEL.

:

REGLER

:

SET

5

3

1

BONJOUR

SET

:

SET

BACK

:

START

:

ACT

I

O

N

SET

C

L

OC

K

DST

:

O

N

2 / 6/

:

2003

THU

12

00

PM

SE

L

E

C

T

HOUR

SE

L

E

C

T

:

1313

Initial Setup

Time Zone Adjust

AUT

O

C

L

OC

K SET

M

A

NU

AL

T

I

M

E

ZO

N

E

A

D

JUS

T

:

0

SELE

C

T

:

SET

:

END

:

ACT

I

O

N

SET

C

L

OC

K

AUT

O

C

L

OC

K SET

M

A

NU

AL

T

I

M

E

ZO

N

E

A

D

JUS

T

:

+1

SELE

C

T

:

SET

:

END

:

ACT

I

O

N

SET

C

L

OC

K

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END

:

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

4)Press and

press SET to

select and set the

month, date, year,

time, and DST

(Daylight Saving

Time)

.

To Make

Corrections,

repeatedly press

to move to error,

then correct.

5)Press ACTION

twice to start the

clock and exit this

mode.

3)Press to

select “TIME

ZONE ADJUST”

and press or

to subtract or

add hour(s) as

necessary.

4)Press ACTION

twice to exit.

• “TIME ZONE ADJUST”

returns to “0” if clock is set

manually.

(Only when Auto Clock is set.)

Add or Delete a Channel

■ Time Zone Adjust

1) Press to

select “CLOCK.”

2) Press SET.

To add channel:

Select channel with NUMBER

keys and press ADD/DLT.

To delete channel:

Select channel with CH

or NUMBER keys and press

ADD/DLT.

C

HANNEL

08

ADDED

C

HANNEL

08

DE

L

E

T

ED

*Important:

If a remote control button does not work when pressed, press

the FM/TV button on the remote and try the button again.

ADD/DLT

ACTION

NUMBER

keys

SELECT

SET

CH

14

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

14

Enjoy the powerful movie theater and hall-like sound available with multiple channel audio found on DVDs

by connecting an ampliﬁ er and speakers. There are two types of connection, digital and analog.

Connect an ampliﬁ er to enjoy high-quality stereo

sound with sampling frequencies of 96 kHz.

■ Analog connection

Connect an ampliﬁ er with Dolby Digital and

DTS decoders to enjoy surround sound.

You can also enjoy stereo sound with sampling

frequencies of 48 kHz if the material is not

copy-protected and the equipment you connect

is compatible with these signals.

■ Digital connection

Audio Connections

Firmly

connect the

cable to the

connector.

Speakers (example)

Connect three or

more speakers for

surround sound.

Speakers (example)

OPTICAL

1515

Initial Setup

IMPORTANT NOTE:

Caution for optical digital audio

output connector:

• When connecting an ampliﬁ er (with an Optical

digital input connector) which does not contain

the Dolby Digital or dts decoder, be sure to

select “PCM” at “Dolby Digital” and “PCM” at

“dts” of the Settings for DVD Operation “AUDIO

OUTPUT” (see page 47). Otherwise, any

attempt to play DVDs may cause such a high

level of noise that it may be harmful to your

ears and damage your speakers.

• When a dts decoder is connected, please

select “Bitstream” at “dts” of the Settings for

DVD Operation “AUDIO OUTPUT.” If “PCM” is

selected, there will be stereo sound. (See

page 47).

• Video CDs and CDs can be played as usual.

• Some dts decoders which do not support

DVD-dts Interface may not work properly with

the unit.

Notes on audio output from the optical

digital audio output con nec tor

Enjoying digital audio output from the

digital audio output con nec tor

*

1

The type of audio output from the connector can be

selected by the Settings for DVD Operation. (See

page 47.)

*

2

Sound having 96 kHz sampling is converted into

48 kHz sampling when it is output from the unit’s

optical digital audio output connector.

For your reference:

• Dolby Digital is a digital sound compression technique

developed by the Dolby Laboratories Licensing Corporation.

Supporting 5.1-channel surround sound, as well as stereo

(2-channel) sound, this technique enables a large quantity of

sound data to be efﬁ ciently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While

CDs are recorded in 44.1 kHz/16 bit, DVDs are recorded in

48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will

obtain the full beneﬁ t of Pro Logic from the same DVD

movies that provide full 5.1 channel Dolby Digital

soundtracks, as well as from titles with the Dolby Surround

mark. For information on Panasonic or Technics Dolby Pro

Logic Surround Sound Decoders please contact your local

dealer.

Disc

Sound

recording

format

Optical digital audio output

from connector

DVD

Dolby Digital

Dolby Digital bitstream

(1-5.1 ch) or PCM (48 kHz

sampling/16 bit only)*

1

Linear PCM

(48/96 kHz

16/20/24 bit)

Linear PCM (2ch)

(48 kHz sampling/16 bit

only)*

2

dts

Bitstream or PCM (48 kHz

sampling/16 bit only)*

1

Video CD MPEG 1

PCM

(44.1 kHz sampling)

CD Linear PCM

Linear PCM

(44.1 kHz sampling)

MP3 MP3

Linear PCM

(It depends on the MP3 ﬁ le)

WMA WMA

Linear PCM

(It depends on the WMA ﬁ le)

Note

Turn down the volume, then turn this unit, as well

as other equipment to be connected, off before

pro ceed ing with connection.

Do not block ventilation holes of any equipment

and arrange them so that air can circulate freely.

Read through the instructions before connecting

other equipment.

Ensure that you observe the color coding when

connecting audio and video cables.

Check List

Manufactured under license from Digital

Theater Systems, Inc. US Pat. No.

5,451,942, 5,956,674, 5,974,380,

5,978,762 and other world-wide patents

issued and pending. “DTS” is a registered

trademark of Digital Theater Systems,

Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D

symbol are trade marks of Dolby

Laboratories.

16

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

16

*

1

Interactive DVD...

May include multiple camera angles, stories, etc.

*

2

Video CD with playback control...

Particular scenes or information can be

interactively selected from a menu that appears

on the screen.

Operation using unit buttons

Basic DVD Operation

NUMBER

keys

POWER

OPEN/

CLOSE

DVD

10

TITLE

MENU

PLAY

SEARCH/

SLOW

RETURN

SKIP+

SEARCH

/SLOW

STOP

PAUSE

SKIP-

Press PLAY.

Insert disc.

Press

OPEN/CLOSE.

2

•

6

3

2

Press STOP.

5

Press POWER.

1

Insert a disc.

• If a disc is already inserted, go to step 3.

(Depending on the disc, playback may start

automatically.)

1) Press OPEN/CLOSE.

2) Place disc into disc tray.

2

• Hold disc by its edges only (page

7) with printed side up and use

guides to place into tray. Use

1

3″(8 cm) or

2

5″ (12 cm) disc.

To return to MENU (play stops)

Press TITLE, MENU, or RETURN. (DVD)

Press RETURN. (Video CD)

Press STOP to stop play.

5

6

Press OPEN/CLOSE to eject the disc.

1

2

Press POWER* on the remote or unit.

Press or

NUMBER key(s)

(see below) to

select title, and

press SET or PLAY

to start playing.

• “Pressing SET or

PLAY” is not

necessary when using

NUMBER keys.

4

Press PLAY to start play. Disc tray

closes automatically.

3

CLOSE

If an interactive DVD*

1

or a Video CD with

playback control*

2

is

used and a TITLE MENU

appears, go to step 4.

• You may also close the

tray by pressing

OPEN/CLOSE.

• Data reading time differs

with each disc.

T

I

TLE MENU

Cas

t

l

es

Love

r

s

B

i

r

ds

Dogs

T

I

TLE MENU

Cas

t

l

es

Love

r

s

B

i

r

ds

Dogs

Dogs

of the world

1 digit number 1 ••• 1

2 digit number 12 ••• 10

➞

1

➞

2

3 digit number 123 •••100

➞

1

➞

2

➞

3

Press SKIP+

|

or SKIP-

|

to go to next or

previous menu screen.

• SKIP function not available with all discs.

Please refer to disc jacket for operation information.

Using NUMBER key(s) starts play automatically.

The number of available titles varies with each disc.

READING

SELECT

SET

Cable or antenna is connected.

Power cord is plugged in.

If unit is connected to an audio ampliﬁ er, turn

the stereo system’s power on.

Check List

1717

DVD Operation

• Please read the disc jacket for operation information.

• If a single sided disc is placed in upside down, “THIS

TYPE OF DISC CANNOT BE PLAYED. PLEASE

INSERT A DIFFERENT DISC” is displayed.

• Remove disc and press unit POWER off when not in

use.

• Disc continues to rotate with menu displayed even

after play is done. Press STOP to clear menu display

when ﬁ nished with menu.

■ Forward/Reverse rapid scene search

➞

Press SEARCH/SLOW

or

SEARCH/SLOW

during play.

➞

Press PLAY to release.

• Starting forward/reverse search during play started from

menu on Video CDs may recall menu.

• Search speed, slow at ﬁ rst, increases with each

additional press of the button up to 5 levels.

• When appears on the screen while a

button is being pressed, it means that the

corresponding operation is prohibited by the

unit or the disc.

The unit memorizes the point where STOP is

pressed.

Press PLAY to resume play from this point.

Pressing STOP again or opening the tray cancels

RESUME, however, RESUME is not canceled

when power is turned off and on.

• RESUME works only with discs for which elapsed

play time is displayed during play.

RESUME function

Power turns off after unit has been in Stop mode

(DVD) for about 5 minutes.

Auto-Power Off function

1. Do steps 1-3 (previous page).

When menu appears, press STOP.

2. Press NUMBER key(s) to select desired

track (play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,

Press STOP, and press PLAY, then the menu

appears. Now, go to step 4 (previous page).

Enjoy Video CDs featuring

playback control without using

menus (Video CDs only)

*Important: I

f a remote control button does not work when pressed, press the DVD button on the

remote and try the button again.

Chapter/Track Chapter/Track Chapter/

T

rackChapter/

T

rack

Current playback position

Reverse Skip Forward Skip

■ Still (Pause) Picture

➞

Press PAUSE during play.

➞

Press PLAY to release

.

• DVD/Video CD : The unit will enter Still picture mode.

• CD : The unit will enter Pause mode.

■ Forward/Reverse Chapter/Track Skip

➞

Press SKIP+

|

or SKIP-

|

during

play.

Each press skips a chapter (DVD) or track

(Video CD/CD).

Pressing SKIP-

|

once midway through a

chapter/track returns to start of that chapter/track.

Each additional press skips back one chapter/track.

• Pressing SKIP+

|

or SKIP-

|

during play

started from menu on Video CDs may recall menu.

■ Frame by Frame picture (DVD/Video

CD)

➞

Press PAUSE in Still mode.

➞

Press PLAY to release.

• Each press advances picture one frame.

• Hold down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically (see page 48).

■ Slow Motion picture (DVD/Video CD)

➞

Press SEARCH/SLOW or

SEARCH/SLOW

(DVD only) in Still

mode.

➞

Press PLAY to release.

• Slow motion speed, slow at ﬁ rst, is increased with

each additional press of the button up to 5 levels.

• Reverse slow motion is not available for video CDs.

Notes

18

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

18

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

TV Operation

1

Press POWER* on the remote or unit.

■ Using the 100 key

When selecting CABLE channels 100 to 125 with

the NUMBER keys, ﬁ rst press the 100 key, and

then enter the remaining two digits.

■ Rapid Tune

Press R-TUNE to display the last channel you

were watching.

■ Audio Mute

Press MUTE to instantly mute the sound. Press

again to restore the previous sound level.

■ Phones

Connect an earphone (not supplied) or headphones

(not supplied) to the Phones Jack.

*

Important:

If a remote control button does not work

when pressed, press the FM/TV button on

the remote and try the button again.

Use CH or

NUMBER keys to

select a channel.

2

3

Press VOL + or

VOL - to adjust

volume.

24

CH08

Cable or antenna is connected.

Power cord is plugged in.

Check List

PHONES

Jack

POWER

VOL +/VOL -

CH

VOL+/-

NUMBER

keys

POWER

MENU

RAPID

TUNE

100 Key

CH

MUTE

1919

TV Operation

MTS Broadcast/TV Stereo System

Receivable Broadcast Types

The following are possible audio broadcast types and on-screen

displays. The signal being received is indicated with an “

”

mark while the selected audio mode is indicated with an arrow.

To change the audio mode for these broadcasts, see the “Audio

Mode for TV Viewing” section below.

Press DISPLAY to display the broadcast signal being

received.

MTS Stereo and SAP broadcast

Multi-channel Television Sound Stereo

(main language) and Secondary Audio

Program (sub language) broadcasts

are being received simultaneously.

Select the STEREO or SAP audio

mode.

MTS Stereo broadcast

Multi-channel Television Sound Stereo

broadcast. Select STEREO audio

mode.

• If stereo broadcast is weak and the

display ﬂ ickers, select MONO audio mode

for possible improvement.

SAP broadcast

Secondary Audio Program (sub

language). Select SAP audio mode for

the sub language.

Audio Mode for TV Viewing

Press AUDIO to select the desired audio mode as described above.

(Arrow shows selection.)

• Each press of AUDIO will change the audio mode as shown below.

• “SAP” is selected with ﬁ rst press of AUDIO.

MONO broadcast

Normal monaural sound broadcast.

1

2

:

0

A

M

CH08

STER

EO

SAP

M

ONO

1

2

:

0

A

M

CH08

STER

EO

SAP

M

ONO

STER

EO

SAP

M

ONO

1

2

:

0

A

M

CH08

STER

EO

SAP

M

ONO

1

2

:

0

A

M

CH08

< Example >

STER

EO

SAP

M

ONO

Press AUDIO

Equipped with -TV Noise

Reduction for true MTS

reproduction.

-TV Noise Reduction is

required for good stereo separation

and audio ﬁ delity.

is a registered trademark, and

is licensed by

Technology

Licensing.

STER

EO

SAP

M

ONO

STER

EO

SAP

M

ONO

DISPLAY

AUDIO

20

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

20

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Closed Caption Mode Feature

1

Closed Caption is ...

This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes

useful information from TV stations available to everyone.

Press ACTION* to display MAIN MENU.

Closed Caption Mode Selections

Caption Mode: CAP C1 or C2

A narration of selected TV

programs is displayed.

Check TV program listings for CC

(Closed Caption) broadcasts.

Caption Mode: TEXT C1 or C2

Most of the screen will be

blocked out. When the TV station

broadcasts information, such as

program listings, it will appear in

this space.

Caption Mode: OFF

Closed Caption/Text narration will

not be displayed.

5

Press ACTION three times to return to

the normal screen.

2

1) Press

to select

“TV.”

2) Press SET to

display SET

UP TV screen.

3

1) Press to

select

“CAPTION.”

2) Press SET to

display

CAPTION

screen.

OFF

CAP C1

TEXT C1

CAP C2

TEXT C2

4

1) Press to

select

CAPTION

MODE.

2) Press SET

repeatedly to

select mode.

(See left.)

CAPT

I

ON

CA

PT

I

O

N

MODE

:

CAP C1

CC ON MUTE

:

CAP C1

SET

:

SET

SE

L

E

C

T

:

END

:

ACT

I

O

N

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

Closed Caption System

• The closed caption or text signal may be

broadcast over C1, C2, or both. Also, text

contents can vary so you may wish to try

different settings.

Note

SELE

C

T

:

END

:

ACT

I

O

N

SET

UP TV

SET

:

SET

CA

PT

I

O

N

I

NP

UT

SELE

C

T

:

T

UNER

SET

UP

V

I

DEO

/

A

UD

I

O

DVD

VOL

AD

JU

ST

:

+

2

F

M

ANT

ENN

A

:

I

NT

2121

TV Operation

1

Caption On Mute Feature

Closed Caption narration, if available, is displayed when

MUTE button is pressed.

Press ACTION to display MAIN MENU.

• When a disc supporting closed caption is

used, the subtitle and the closed caption may

overlap. In this case, turn the subtitle or

caption on mute mode off. (See page 34.)

2

1) Press to

select “TV.”

2) Press SET to display

SET UP TV screen.

6

Press ACTION three times to return to the normal

screen.

7

Press MUTE to mute the sound and display

closed captioning.

• To cancel, press MUTE again.

3

1) Press to select

“CAPTION.”

2) Press SET to display

CAPTION screen.

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

4

1) Press to select

CAPTION MODE.

2) Press SET repeatedly

to select “OFF.”

NO

CAP C1

CAP C2

5

1) Press to select

CC ON MUTE.

2) Press SET repeatedly

to select desired mode.

• Each press of SET will change

the display as shown left.

• The caption may be broadcast

over CAP C1 or C2.

CAPT

I

ON

CA

PT

I

O

N

MODE

:

OFF

CC ON MUTE

:

CAP C1

SET

:

SET

SE

L

E

C

T

:

END

:

ACT

I

O

N

*Important: I

f a remote control button does not work when pressed, press the FM/TV button

on the remote and try the button again.

MUTE

ACTION

Note

SELECT

SET

SELE

C

T

:

END

:

ACT

I

O

N

SET

UP TV

SET

:

SET

CA

PT

I

O

N

I

NP

UT

SELE

C

T

:

T

UNER

SET

UP

V

I

DEO

/

A

UD

I

O

DVD

VOL

AD

JU

ST

:

+

2

F

M

ANT

ENN

A

:

I

NT

22

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

22

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

TV Timer Features

1

ON-TIMER with Alarm

This unit can be set to automatically power on in one of

3 modes (TV, FM radio, or DVD/Video CD/CD.) You

can also combine the On-Timer with a one minute

alarm that gradually increases in volume.

• If no button on the remote or unit (including a

button used to turn off the alarm) is pressed

within 60 minutes after unit turns itself on, it will

turn itself back off.

Press TIMER* to display SET TIMER screen.

To Cancel ON-TIMER,

Repeat steps 1 and 2. Then, press ADD/DLT to clear

the time in step 3. Now, press TIMER to end.

“ON TIMER END” brieﬂ y appears on-screen.

2

1) Press to select

“ON TIMER.”

2) Press SET to

display ON TIMER

screen.

3

• ON-TIMER mode

selection order

1) Press to select

desired settings.

2) Press SET to set

the ON-TIMER

time or ON-TIMER

mode.

• Make sure a disc is

inserted if DVD

(DVD/Video CD/CD)

mode is selected.

• See “FM Radio” on pages

24 and 25 for instructions

on how to preset FM

stations.

4

Press to select

ALARM “ON” or

“OFF.”

When “ON” is selected,

an alarm will gradually increase in volume for one

minute or until canceled by pressing any button

(including VOL + -).

To Make Corrections,

use

and to move back and correct.

5

Press TIMER to set ON TIMER.

• “ON TIMER SET” is displayed.

• ON-TIMER Indicator lights up on the unit.

Sleep Timer

This unit can be set for auto power off.

Press TIMER to display SET TIMER

screen.

1

To cancel,

press SET repeatedly until 00 appears.

2

1) Press to

select SLEEP

TIMER.

2) Press SET

repeatedly to

select the

desired time.

3

Press TIMER to return to the

normal screen.

• Pressing DISPLAY with sleep timer set

displays remaining time.

• SLEEP TIMER Indicator lights up on the

unit.

SLEEP TIMER 30 60 90 00

SLEEP TIMER Indicator

ON TIMER Indicator

SET

:

SET

SE

L

E

C

T

:

END

:

T I MER

SET TIMER

ON T

I

MER

S

LEEP

T

I

MER : 00

SET

:

SET

SE

L

E

C

T

:

END

:

T I MER

SET TIMER

ON T

I

MER

S

LEEP

T

I

MER : 00

O

N T

I

M

E

R

SE

L

E

C

T

H

OU

R

SET

:

SET

SE

L

E

C

T

:

END

:

T I MER

ALAR

M

:

O

N

O

N T

I

M

E

R

SE

L

E

C

T

ALARM

SET

:

SET BACK

:

SE

L

E

C

T

:

END

:

T I MER

ALAR

M

:

O

N

C

ANCEL

:

ADD / DLT

FM1

C

H

01

C

H

125

FM8

FM9

C

H

02

C

H

03

DVD

Note

The clock is set to the correct time.

Check List

2323

TV Operation

TV Status & Clock Display

Press DISPLAY to display or remove the overlay.

Blue Screen Display

When you change channels, the channel number will be

displayed.

Channel Display

Whenever the selected channel has no broadcast signal with the

Weak Signal Display Feature set to “OFF” (see page 26), the

screen will turn solid blue.

*

Important: If a remote control button does not work when pressed, press the

FM/TV

button on the remote and

try the button again.

DISPLAY

ADD/DLT

TIMER

CH08

STER

EO

SAP

M

ONO

Current Time

Receivable

Broadcast Types

(See page 19.)

Channel

CH08

On-Screen Display (OSD)

SELECT

SET

24

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

24

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

1) Press CH to

select the desired

radio station.

(Each

press changes

frequency by 200

kHz.)

2) Press ADD/DLT to

set the radio

station.

Hold down CH

or

for a few

seconds, then

release to quickly

scan for FM

stations in your

area.

• To cancel, press CH

or

while in search

mode.

FM Radio

F

M

1 87. 5

M

Hz

1

2

:

0

P

M

F

M

1 8

7.

7

M

Hz

MEM

O

RY

:

PRESS

ADD

/

DLT

KEY

1

2

:

0

P

M

F

M

1 8

7.

7

M

Hz

MEM

O

R

I

ZED

1

2

:

0

P

M

2

Press a NUMBER

key (1~9) to select the

FM preset number.

1

To Make Corrections,

select station with a NUMBER key, then do step 3

again.

To exit FM mode,

press FM/TV or DVD on the remote.

3

FM Radio Setup

Press FM/TV* on the remote to display FM

radio mode.

FM Radio is ...

This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1

MHz. You can set the On-Timer (page 22) to wake up to your favorite radio station.

CH

2525

TV Operation

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

FM Antenna Setup

1

2

Make sure FM tuning is done correctly (see FM

Radio Setup).

Press ACTION to display MAIN MENU.

1) Press to

select “TV.”

2) Press SET to

display SET UP TV

screen.

3

4

■

For cable TV users

➞

“INT”

■

For antenna users

➞

“EXT”

2

1

To exit FM mode,

press FM/TV or DVD on the remote.

Press a NUMBER key

(1~9) to select a preset

FM number

(see FM Radio Setup

on page 24).

Using FM Radio

Press ACTION twice to end setup.

Press FM/TV on the remote to display

FM radio mode.

• You may get better reception by repositioning

the unit.

• You cannot select FM Radio mode while a blue

back screen (ACTION, MENU) is displayed.

• Once stations are set, the selected station and

current time are displayed when FM Radio mode

is entered. To remove time, press DISPLAY. If

DISPLAY is pressed again, the unit status

screen appears.

Audio Mode for FM Radio

Press AUDIO

repeatedly to

select “STEREO”

or “MONO” in FM

Radio mode.

1) Press to

select FM

ANTENNA.

2) Press SET to

select “INT

(INTERNAL)” or

“EXT

(EXTERNAL)” to

determine which

one sounds best.

F

M

1 87. 5

M

Hz

1

2

:

0

P

M

STERE

O

M

ONO

F

M

1 8

7.

7

M

Hz

1

2

:

0

P

M

FM/TV

DVD

CH

NUMBER

keys

ADD/DLT

DISPLAY

AUDIO

ACTION

Notes

SELECT

SET

SELE

C

T

:

END

:

ACT

I

O

N

SET

UP TV

SET

:

SET

CA

PT

I

O

N

I

NP

UT

SELE

C

T

:

T

UNER

SET

UP

V

I

DEO

/

A

UD

I

O

DVD

VOL

AD

JU

ST

:

+

2

F

M

ANT

ENN

A

:

I

NT

26

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

26

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Special Features

■ Auto Shut Off

No broadcast signal in TV mode (Only when Weak

Signal Display is set to OFF.), DVD stops for 5

minutes.

➞

Power turns off

• This feature is canceled if any button is pressed

during above conditions.

Auto Operation Functions

ADD/DLT

ACTION

CH

SURROUND/

VSS

When “ON” is selected, the picture is displayed

even when a broadcast signal is weak or

non-existent.

Weak Signal Display Feature

1

2

3

• “ON” = Picture is displayed regardless of signal

condition, and may not always be clearly

visible.

“OFF” = Screen turns solid blue when signal is absent

or weak.

• If unit is connected to equipment which has blue back

feature, selecting “ON” will have no effect on the other

equipment.

4

Press ACTION* to display MAIN MENU.

1) Press

to select

“CH.”

2) Press SET to

display SET

UP CHANNEL

screen.

Press ACTION twice to return to the

normal screen.

1) Press to

select WEAK

SIGNAL

DISPLAY.

2) Press SET to

set “ON” or

“OFF.”

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END

:

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

ANT

ENN

A

:

C

ABLE

A

U

T

O

S

E

T

W

EAK S

I

GNAL

D

I

SPLAY

:

OFF

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

SET UP

CH

A

NNE

L

Notes

Selecting Input Mode

Method 1:

Press CH . The display will change as

follows.

1

2

3

125LINE1

(CABLE)

69

(TV)

or

LINE2

Method 2:

a Press ACTION for MAIN MENU.

b Press

to select “TV,” then press SET

for SET UP TV screen.

c Press

to select “INPUT SELECT,” and

then press SET to select “TUNER,” “LINE1” or

“LINE2.”

d Press ACTION twice to exit this mode.

SELECT

SET

2727

Advanced Operation

*

Important:

If a remote control button does not work when pressed, press the FM/TV button on

the remote and try the button again.

DVD Volume Adjust

1

Some DVDs are recorded in lower average volume

level. For these DVDs, this unit can be set so that

the average volume is increased automatically.

Press ACTION to display MAIN MENU.

2

1) Press

to select

“TV.”

2) Press SET to

display SET UP

TV screen.

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

3

1) Press to

select DVD

VOL ADJUST.

2) Press SET to

set the level (0,

+1, or +2).

4

Press ACTION twice to return to the

normal screen.

VSS OFF

Enjoy a surround-like effect if you are using two

front speakers only. The effect is broadened and

sound seems to come from virtual speakers on

either side if the disc has surround signals

recorded on it.

Press VSS in DVD mode.

• The Surround sound effects can be changed by

pressing VSS repeatedly as shown by the ﬁ gure

below.

• V.S.S. effects is available in DVD mode only.

• Turn off the surround effects on the other equipment.

• V.S.S. will not work, or will have less effect, with some

discs.

• Turn V.S.S. off if it causes distortion.

V.S.S. (Virtual Surround Sound)

[DVD only]

You can hear a deeper, 3-D sound effect using just

the unit’s two front speakers.

Press SURROUND.

• “SURROUND ON” is displayed.

SURROUND ON

To Cancel,

press SURROUND.

• Surround sound effect is not available for normal

(mono) broadcasts.

• The surround effect (TV mode only) is not output to

Audio Output L/R Connector.

Surround Sound System

SURROUND OFF

VSS1

VSS3

VSS2VSS OFF (default)

Notes

SELE

C

T

:

END

:

ACT

I

O

N

SET

UP TV

SET

:

SET

CA

PT

I

O

N

I

NP

UT

SELE

C

T

:

T

UNER

SET

UP

V

I

DEO

/

A

UD

I

O

DVD

VOL

AD

JU

ST

:

+

2

F

M

ANT

ENN

A

:

I

NT

28

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

28

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Press ACTION* to display MAIN MENU.

Enter Secret Code

A 4-digit code must be entered to view a blocked

program or change rating settings.

1

• DO NOT forget your secret code.

• Once ratings are set, restricted programs

cannot be accessed unless the secret code is

entered.

Changing your secret code

• You will need your current code.

Do steps 1 ~ 3. In step 4, press CLEAR to clear

current code.

Repeat steps 3 and 4 to enter new code.

Process of V-Chip Control Feature

Setup Blocking

Enter Code

Press SET to display

US Ratings menu (see

pages 29, 30).

Or

Press ACTION twice

to exit.

4

1) Press NUMBER

keys to enter your

secret code.

2) Enter same code

again for

conﬁ rmation.

3

• Step 2) not necessary when changing rating or

secret code.

• Take care that you are not observed entering the

secret code.

To Make Corrections

Press

repeatedly to move the cursor.

Press NUMBER keys to make the correction.

1) Press to

select “LOCK.”

2) Press SET to

display LOCK

screen.

2

V-Chip Control Feature is...

This unit has a built-in V-Chip Control which allows you

to block unwanted TV usage based on US MOVIES and

US TV PROGRAMS Ratings.

LOCK

RECOGN

I

ZED

CHANGE

CODE

:

ADD

/

DLT

CONT

I

NUE

:

SET

END

:

ACT

I

O

N

CONF

I

RM 4

-

D

I

G

I

T CODE

****

BACK SPACE

:

ENTER

:

0

-

9

END

:

ACT

I

O

N

LOCK

ENTER 4

-

D

I

G

I

T

CODE

-

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

V-Chip Control Feature

NUMBER

key

CLEAR

ACTION

SELECT

SET

Notes

2929

Advanced Operation

1

1) Press to select

US MOVIES.

2) Press SET to set

“ON” or “OFF.”

If LOCK menu is not displayed, perform “Enter

Secret Code” steps on page 28.

■ “ON”

➞

V-Chip Control is activated.

■ “OFF”

➞

V-Chip Control is deactivated.

US MOVIES Ratings

US MOVIES RATINGS

*

Important:

If a remote control button does not work when pressed, press the FM/TV button on the

remote and try the button again.

2

1) Press to select

CHANGE

SETTINGS.

2) Press SET to

display screen.

3

1) Press to select

VIEW NR

PROGRAMS?.

2) Press SET to set

“YES” or “NO.”

NR (Not Rated) PROGRAMS

Some movies, such as old movies or foreign

movies usually have no ratings.

4

Press to select

and SET to set

ratings to be blocked.

(See ratings chart on

this page.)

5

Press ACTION to redisplay LOCK

menu and continue with US TV

PROGRAMS Ratings (page 30).

Or,

press ACTION three times to exit.

• “NEXT PAGE” displays CANADIAN V-Chip setting

menu. Not necessary except when viewing

Canadian discs or broadcasts.

US MOV

I

ES

:

O

FF

CHANGE

SET

T

I

NGS

US

TV

PROGRAMS

:

O

FF

CHANGE

SET

T

I

NGS

DVD

LOCK

:

O

FF

CHANGE

SET

T

I

NGS

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

LOCK

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

LOCK

US MOV

I

ES

:

O

FF

CHANGE

SET

T

I

NGS

US

TV

PROGRAMS

:

O

FF

CHANGE

SET

T

I

NGS

DVD

LOCK

:

O

FF

CHANGE

SET

T

I

NGS

Process of V-Chip Control Feature

Setup

BlockingEnter Code

G

GENERAL AUDIENCE:

All ages admitted.

PG

PARENTAL GUIDANCE:

Some material may not be suitable

for children.

PG-13

PARENTS CAUTIONED:

Some material may be inappropriate

for children under 13.

R

RESTRICTED:

Children under 17 must be

accompanied by a parent or adult.

NC-17

OVER AGE 17 ONLY:

No one 17 and under admitted.

X ADULTS ONLY:

Note

30

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

30

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

US TV PROGRAMS RATINGS: Chart 1

US TV PROGRAMS RATINGS: Chart 2

1

1) Press * to

select US TV

PROGRAMS.

2) Press SET to set

“ON” or “OFF.”

US TV PROGRAMS Ratings

If LOCK menu is not displayed, do “Enter

Secret Code” steps on page 28.

US MOV

I

ES

:

O

FF

CHANGE

SET

T

I

NGS

US

TV

PROGRAMS

:

O

FF

CHANGE

SET

T

I

NGS

DVD

LOCK

:

O

FF

CHANGE

SET

T

I

NGS

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

LOCK

2

1) Press to select

CHANGE

SETTINGS.

2) Press SET to

display screen.

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

LOCK

US MOV

I

ES

:

O

FF

CHANGE

SET

T

I

NGS

US

TV

PROGRAMS

:

O

FF

CHANGE

SET

T

I

NGS

DVD

LOCK

:

O

FF

CHANGE

SET

T

I

NGS

NR (Not Rated) PROGRAMS

Some TV shows, such as news, sports, weather,

bulletins, emergency information usually have no

ratings.

3

1) Press to select

VIEW NR

PROGRAMS?.

2) Press SET to set

“YES” or “NO.”

TV

-

Y

TV

-

Y7

TV

-

G

TV

-

PG

TV

-

1

4

TV

-

MA

FV

V

S L D

V

S L D

V

S L

UNLOCKED

V

I

E

W

NR

PROGRAMS

?

:

YES

CONTA

I

NS NO RAT

I

NG

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

• You may select from standard TV ratings (chart 1), or

customize to a speciﬁ c content rating (chart 2).

4

Press to select

and SET to set ratings

to be blocked.

(See ratings charts on

this page.)

• Ratings highlighted in

green will be blocked.

Ratings in white letters

will not be blocked.

V

I

E

W

NR

PROGRAMS

?

:

YES

FOR

ALL

CH

I

LDREN

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

TV

-

Y

TV

-

Y7

TV

-

G

TV

-

PG

TV

-

1

4

TV

-

MA

FV

V

S L D

V

S L D

V

S L

UNLOCKED

5

Press ACTION three times to exit this mode.

• “NEXT PAGE” displays CANADIAN V-Chip setting

menu. Not necessary except when viewing Canadian

discs or broadcasts.

V-Chip Control Feature (continued)

FV Fantasy Violence

V Violence

S Sexual Situations

L Adult Language

D Sexually Suggestive Dialogue

TV-Y FOR ALL CHILDREN:

Content speciﬁ cally geared to young

viewers ages 2-6.

TV-Y7 FOR AGE 7 AND OLDER:

May contain mild physical or comedic

violence which may frighten children

under 7.

TV-G GENERAL AUDIENCE:

Contains little or no violence, strong

language, or sexual dialogue or

situations.

TV-PG PARENTAL GUIDANCE:

May contain infrequent coarse

language, limited violence, some

suggestive sexual dialogue and

situations.

TV-14 PARENTS CAUTIONED:

May contain sophisticated themes,

sexual situations, strong language,

and more intense violence.

TV-MA MATURE AUDIENCE:

May contain mature themes, profane

language, graphic violence, and

sexual situations.

■ “ON”

➞

V-Chip Control is activated.

■ “OFF”

➞

V-Chip Control is deactivated.

Note

Process of V-Chip Control Feature

Setup

BlockingEnter Code

Note

3131

Advanced Operation

*

Important:

If a remote control button does not work when pressed, press the FM/TV button on the

remote and try the button again.

Blocking Message

• If a program or movie

exceeds the ratings you

have set, a message will

appear on a black

background and sound is

muted.

To View a Blocked Program/Movie

[Temporarily Deactivate V-Chip Control]

Enter your secret code (ACCESS CODE) in the

Blocking Message screen.

• V-Chip Control is reactivated when power is turned off

or power failure occurs.

[Deactivate V-Chip Control]

Enter your secret code (steps 1-3 page 28). Then,

set US MOVIES and/or US TV PROGRAMS to

“OFF” using

and SET. (Ratings set on pages

29 and 30 is retained and will be in effect when

V-Chip Control is activated again.)

CH08

RAT

I

NG

:

PG

-

1

3

ACCESS

CODE

----

PROGRAM

RAT

I

NG

EXCEEDED

ENTER :

0

-

9

Process of V-Chip Control Feature

Setup

Blocking

Enter Code

ACTION

SELECT

SET

32

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

32

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

1

Press ACTION* to display MAIN MENU.

Audio Menu

Video Menu

a

Do steps 1 - 3 left.

This feature allows easy setting of picture and sound suitable for each program source.

1) Press to

select “AUDIO

MENU.”

2) Press SET to

select desired

mode. (See

below.)

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

SET

UP

V

I

DEO

/

A

UD

I

O

V

I

D

E

O

MENU

:

NO

RM

A

L

V

I

D

E

O

AD

J

UST

A

UD

I

O

MENU

:

MU

S

I

C

A

UD

I

O

AD

J

UST

b

c

Press ACTION three times to end setup.

• The effects of this feature on the signal is not output

to the Audio/Video Output Connector.

• When AUDIO MENU mode is “AUTO,” the AUDIO

ADJUST setting will be “STANDARD.”

• AUDIO MENU settings remain in memory.

• VIDEO MENU settings do not remain in memory.

1) Press to

select “VIDEO

MENU.”

2) Press SET

repeatedly to

select desired

mode. (See

below.)

4

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

SET

UP

V

I

DEO

/

A

UD

I

O

V

I

D

E

O

MENU

:

NO

RM

A

L

V

I

D

E

O

AD

J

UST

A

UD

I

O

MENU

:

MU

S

I

C

A

UD

I

O

AD

J

UST

5

Press ACTION three times to end setup.

1) Press

to select “TV.”

2) Press SET to

display SET

UP TV screen.

2

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

1) Press to

select

“SET UP

VIDEO/AUDIO.”

2) Press SET to

display.

3

[Audio Menu]

■ NORMAL

■ AUTO

[Audio AGC (Auto Gain Control)]

The sound level is automatically adjusted to suit

the program source (see below left).

■ MOVIE

Sound suited to movies.

■ MUSIC

Sound suited to music. (Factory setting)

■ SPEECH

Sound suited to dialogue.

[Video Menu]

■ NORMAL

Factory setting.

■ MOVIE

Picture is adjusted for a movie-like feel.

■ NIGHT

Color and picture intensity are adjusted to be

easier on the eyes for night viewing.

Low

Standard

High

Volume level

TV TV

CD

AUDIO MENU : NORMAL

Volume level

Low

Standard

High

TV TV

CD

AUDIO MENU : AUTO

Video/Audio Menu

ACTION

Notes

SELECT

SET

SELE

C

T

:

END

:

ACT

I

O

N

SET

UP TV

SET

:

SET

CA

PT

I

O

N

I

NP

UT

SELE

C

T

:

T

UNER

SET

UP

V

I

DEO

/

A

UD

I

O

DVD

VOL

AD

JU

ST

:

+

2

F

M

ANT

ENN

A

:

I

NT

3333

Advanced Operation

*

Important:

If a remote control button does not work when pressed, press the FM/TV button on the remote

and try the button again.

1

Press ACTION to display MAIN MENU.

Audio Adjustment

Video Adjustment

6

Press ACTION four times to end setup.

1) Press

to select “TV.”

2) Press SET to

display SET

UP TV screen.

2

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

1) Press to

select

“SET UP

VIDEO/AUDIO.”

2) Press SET to

display.

3

1) Press to

select “VIDEO

ADJUST.”

2) Press SET to

display.

4

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

SET

UP

V

I

DEO

/

A

UD

I

O

V

I

D

E

O

MENU

:

NO

RM

A

L

V

I

D

E

O

AD

J

UST

A

UD

I

O

MENU

:

MU

S

I

C

A

UD

I

O

AD

J

UST

To Reset VIDEO Controls,

press

and SET to select and set

“STANDARD.” All controls return to their factory

settings.

5

CO

L

OR

T

I

NT

B

R

I

GH

T

N

E

SS

P

I

C

T

UR

E

SH

A

R

P

N

E

SS

ST

A

N

D

ARD

ADJUST

:

SE

L

E

C

T

:

END

:

ACT

I

O

N

V

I

DEO ADJUST

1) Press to

select an item.

(See below.)

2) Press

to

adjust.

[VIDEO Adjustment]

■ COLOR Control

Adjust color intensity.

■ TINT Control

Adjust for natural ﬂ esh tones.

■ BRIGHTNESS Control

Adjust picture brightness.

■ PICTURE Control

Adjust picture intensity by adjusting both

contrast and color level in the proper balance.

■ SHARPNESS Control

Adjust picture sharpness.

f

Press ACTION four times to end setup.

d

e

BASS

TREBLE

BALANCE

ST

A

N

D

ARD

ADJUST

:

SE

L

E

C

T

:

END

:

ACT

I

O

N

AUDIO ADJUST

[AUDIO Adjustment]

■ BASS Control

To adjust the intensity of low frequency sound.

■ TREBLE Control

To adjust the intensity of high frequency sound.

■ BALANCE Control

To adjust the (L/R) unit speaker output level.

• The levels set here do not affect other audio

equipment when connected to the Audio Output

L/R Connector.

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

SET

UP

V

I

DEO

/

A

UD

I

O

V

I

D

E

O

MENU

:

NO

RM

A

L

V

I

D

E

O

AD

J

UST

A

UD

I

O

MENU

:

MU

S

I

C

A

UD

I

O

AD

J

UST

a

Press ACTION to display MAIN MENU.

1) Press

to select “TV.”

2) Press SET to

display SET UP

TV screen.

b

1) Press to

select

“SET UP

VIDEO/AUDIO.”

2) Press SET to

display.

c

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

1) Press to

select “AUDIO

ADJUST.”

2) Press SET to

display.

1) Press to

select an item.

(See below.)

2) Press

to

adjust.

To Reset AUDIO Controls,

press

and SET to select and set

“STANDARD.” All controls return to their factory

settings.

Video/Audio Adjustment

SELE

C

T

:

END

:

ACT

I

O

N

SET

UP TV

SET

:

SET

CA

PT

I

O

N

I

NP

UT

SELE

C

T

:

T

UNER

SET

UP

V

I

DEO

/

A

UD

I

O

DVD

VOL

AD

JU

ST

:

+

2

F

M

ANT

ENN

A

:

I

NT

SELE

C

T

:

END

:

ACT

I

O

N

SET

UP TV

SET

:

SET

CA

PT

I

O

N

I

NP

UT

SELE

C

T

:

T

UNER

SET

UP

V

I

DEO

/

A

UD

I

O

DVD

VOL

AD

JU

ST

:

+

2

F

M

ANT

ENN

A

:

I

NT

34

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

34

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Press SUB TITLE* in

Play mode to display

the subtitle selection

on-screen.

• Display disappears

after 5 seconds.

• When no subtitles are

offered, “-” will be

displayed instead of

the language number.

AUDIO:3 ESP

Dolby Digital 3/2.1ch

Hola

SELECT :

END : AUDIO

AUDIO:1 ENG

Dolby Digital 3/2.1ch

Hello

SELECT :

END : AUDIO

Te amo

• When closed captioning is used along with subtitles, they may

overlap. If so, turn one function off. (See pages 20 and 21.)

• If after several presses of the button the language does not

change, language selection is not offered on the disc.

• Subtitles may not change to the selected language

immediately.

• When disc is removed, subtitles revert to initial setting

language. If the initial language is not recorded on the disc,

the disc’s priority language will appear.

You can select a different subtitle language (if offered)

than the one set at the Settings for DVD Operation. (See

page 46.)

1) Press to select

desired language.

2) Press

(or ) to

select “ON” or

“OFF.”

Subtitle Language (DVD only)

[

Subtitle language]

[Audio soundtrack language]

• Change the No. by pressing , and press

SET.

You can change the audio soundtrack language,

selected at the Settings for DVD Operation, to a

different language if available. (See page 46.)

(This operation works only with discs on which multiple

audio soundtrack languages are recorded.)

Press AUDIO in Play

mode to display the

audio selection

on-screen.

Audio Soundtrack Language (DVD only)

Audio attribute 1 type,

sampling frequency, bit

No. of the disc.

[Audio attribute 1 type, sampling

frequency, bit No. of the disc (see

page 47)

]

1

2

a

b

Number of subtitle language being played back.

Press to select

desired language.

Audio soundtrack

language being played

back.

• If, after several presses of the AUDIO button the

language does not change, language selection is

not offered on the disc.

• When disc is removed, language reverts to initial

setting. If this language is not recorded on the disc,

the language recorded will be heard.

• Display disappears after

5 seconds.

Disc Operation

ENG English

FRA French

DEU German

ITA Italian

ESP Spanish

NLD Dutch

SVE Swedish

NOR Norwegian

DAN Danish

POR Portuguese

RUS Russian

JPN Japanese

CHI Chinese

KOR Korean

MAL Malay

VIE Vietnamese

THA Thai

Other

LPCM

96 kHz

or

48 kHz

16 bit

Linear PCM disc20 bit

24 bit

Dolby

Digital

1 ch - 5.1 ch Dolby Digital disc

dts 1 ch - 5.1 ch dts disc

Notes

Please read “Basic DVD Operation” on

page 16.

Check List

3535

Advanced Operation

SELECT :

END : AUDIO

When

appears on the screen while a

button is being pressed, it means that the

corresponding operation is prohibited by

the unit or the disc.

• ANGLE Indicator lights up on the unit when

a scene recorded at different angles is

detected.

• The angle number can be set beforehand

so that the angle is switched whenever

ANGLE Indicator lights up.

a

Press AUDIO in Play mode to display the audio

screen.

Vocal selection for Karaoke discs (DVD/Video CD)

DVDs may contain scenes shot from multiple camera

angles allowing the same scene to be viewed at different

angles. You can view these angles, if available, using the

ANGLE button.

1

Press ANGLE in Play

mode to display the angle

selection on-screen.

• Display disappears after 5

seconds.

Multiple Angle Viewing (DVD only)

2

Press to select the

desired angle.

b

1) Press (or ) to

select as shown below.

2) Press

(or ) to set.

(DVD only)

Number of angle being played back.

You can enlarge speciﬁ c portions of a picture and select the

zoom ratio using the ZOOM button on the remote during

DVD playback.

Set Zoom size.

Press ZOOM repeatedly to change display as follows.

Picture Zoom (DVD only)

• You can enlarge the center portion of the image to one of 2

magniﬁ cations.

• Closed captioning will not be displayed

while Picture Zoom is used. To see

subtitles, set the subtitle feature to ON (see

page 34).

• The subtitle cannot be enlarged nor can it’s

position be changed.

• The picture zoom feature does not work

with a Video CD.

• During picture zoom, “ZOOM1” or “ZOOM2”

appears on-screen for 5 second.

• Zooming, on some discs, may result in poor

picture quality, or may not operate at all.

X 1.0 (ORIGINAL)

1st press

2nd press

3rd press

X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)

ZOOM 1

ZOOM 2

■ Use the , , and buttons to move the

position up, down, left and right.

*

Important:

If a remote control button does not work when pressed, press the DVD button on the

remote and try the button again.

ANGLE Indicator

ANGLE

SUB TITLE

AUDIO

ZOOM

Notes

SELECT

SET

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1

+

V2 VOCAL OFF

• Video CD LR L R

36

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

36

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Some DVDs have more than one title, e.g. movies. If

the disc offers a title menu, you can select the desired

title number. (Operation may vary according to the disc.)

1

Press TITLE* in Play

mode to display title

screen.

Title menu (DVD only)

DVDs may offer a special menu. This menu may

include guides to unique contents, audio/subtitle

languages, etc. Although contents and operation may

vary, the following steps show basic steps for using the

menu.

a

b

Press MENU in Play

mode to display DVD

menu.

1) Press or

NUMBER key(s) to

select an item.

2) Press SET or

PLAY to access.

DVD menu (DVD only)

2

1) Press or

NUMBER key(s) to

select a title.

2) Press SET or

PLAY to start play.

• Step 2) not necessary

when using NUMBER

key(s).

• Step 2) not necessary

when using NUMBER

key(s).

Repeat step “b” if there is more than one menu.

T I TLE MENU

Cas

t

l

es

Love

r

s

B

i

r

ds

Dogs

T

I

TLE MENU

Cas

t

l

es

Love

r

s

Dogs

B

i

r

ds

DVD MENU

3 . ANGLE

1 . SUBT

I

TLE

2 . AUD

I

O

DVD MENU

3 . ANGLE

1 . SUBT

I

TLE

2 . AUD

I

O

B

i

rds

of the world

Disc Operation (continued)

NUMBER

key

CLEAR

TITLE

MENU

ACTION

PLAY

STOP

SELECT

SET

DISPLAY

3737

Advanced Operation

• Up to 15 tracks can be programmed.

• “

” or “ ” (depending on disc) indicates additional

PROGRAM PLAY screen. Press

for next or

previous screen.

• To clear the last program one by one,

Press

to move to “CLEAR LAST” and press

SET. (Pressing CLEAR also clears last program.)

• To clear all programs,

Press

to move to “CLEAR ALL” and press SET.

(Programs are also cleared when the power is turned off or the

disc is removed.)

You can program speciﬁ c tracks and order of

play.

Program Play (Video CD/CD)

1

Press ACTION in Stop mode to display MAIN

MENU.

6

1) Press to

select “START.”

2) Press SET to start

play of programs in

the sequence

selected.

•To cancel, press STOP during play, then press CLEAR.

*

Important:

If a remote control button does not work when pressed, press the FM/TV, DVD button

on the remote and try the button again.

2

1) Press to

select “DVD.”

2) Press SET to

display screen.

3

1) Press to select

“PLAY MODE.”

2) Press SET to

display screen.

4

1) Press to select

“PROGRAM

PLAY.”

2) Press SET to

display screen.

5

1) Press to

select a track

number. (Track

numbers on disc

are displayed.)

2) Press SET to set.

•Repeat step 5 to select another track.

•The selected track is added on the right side.

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

4:3 Pan & Scan

PLAY MODE

SELECT :

SET : SET

END : ACTION

PROGRAM PLAY

SELECT :

SET : SET

END : ACTION

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6

3 8 13 18 1 13

4 9 14 19 3 2

5101520 2

CLEAR LAST

CLEAR ALL START

PROGRAM PLAY

SELECT :

SET : SET

END : ACTION

DI SC PROGRAM

1 61116 5 8

2 7 12 17 15 6

3 8 13 18 1 13

4 91419 3 2

5101520 2

CLEAR LAST

CLEAR ALL START

Program Repeat Play

(Video CD/CD)

d

Press SET to enter Select mode.

Cursor move to “OFF.”

e

Press to select “DISC.”

(Unit Information Screen)

a

Do steps 1 through 6 on this page.

b

Press DISPLAY to display Disc

Information screen.

(Disc Information Screen)

c

Press DISPLAY again to display Unit

Information screen.

f

Press SET to set mode. Cursor move

to “REPEAT.” To cancel, select

“REPEAT: OFF” in step e, then press

SET.

SELECT :

SET : SET END : DISPLAY

PLAY

REPEAT: DISC

PROGRAM PLAY

SET : SET END : D ISPLAY

SET : SET NEXT : DISPLAY

TRACK : 1 VIDEO CD

PBC : OFF 1 : 35 : 12

Notes

Unit is in TV mode, press FM/TV.

Video CD or CD is inserted.

Check List

38

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

38

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Tracks are played in a random order.

Random Play (Video CD/CD)

Press ACTION* in Stop mode to display

MAIN MENU.

1

1) Press

to select “DVD.”

2) Press SET to

display screen.

2

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

1) Press to select

“PLAY MODE.”

2) Press SET to

display screen.

3

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

4:3 Pan & Scan

1) Press to select

“RANDOM PLAY.”

2) Press SET to begin

random play.

• To cancel, press STOP during play, then press CLEAR.

4

PLAY MODE

SELECT :

SET : SET

END : ACTION

*

Important: If a remote control button

does not work when pressed,

press the FM/TV button on

the remote and try the button

again.

Disc Operation (continued)

CLEAR

ACTION

STOP

SELECT

SET

3939

Advanced Operation

1

Press DISPLAY in Play or Stop mode to display

“On-Screen Display.”

When DISPLAY is pressed, On-Screen Displays show disc

information (title/chapter/track number, elapsed playing

time) and unit information (Repeat Play, Play mode).

• Each press of DISPLAY changes the on-screen display

as follows. (Please refer to page 40 or 41.)

3

1) Press to select the setting.

2) Press SET to set.

To return to the

normal screen,

press CLEAR or

DISPLAY repeatedly.

SELECT :

SET : SET NEXT : DISPLAY

T I TLE : 12 DVD

CHAPTER : 11 0:12:34

SELECT :

SET : SET NEXT : DISPLAY

T I TLE : 12 DVD

CHAPTER : 24 0:12:34

2

1) Press (or ) to select an item.

2) Press SET to set.

SET : SET NEXT : DISPLAY

TRACK : 12 VIDEO CD

PBC : OFF 0 : 12 : 34

SET : SET NEXT : DISPLAY

TRACK : 17 VIDEO CD

PBC : OFF 0 : 12 : 34

• When DISPLAY is pressed during

play of a Video CD with Play control,

the NUMBER keys are not available

on the displayed screen. In this case,

press DISPLAY again to remove the

displayed screen.

• When

appears on the screen while

a button is being pressed, it means

that the corresponding operation is

prohibited by the unit or the disc.

• DISPLAY button does not function while DVD TITLE MENU

is displayed.

DVD Operation using On-Screen Displays

NUMBER

keys

CLEAR

DISPLAY

Note

Notes

SELECT

SET

Selected disc information

Normal Screen

Selected unit information

• When numbers are

displayed (e.g. title

number), the NUMBER

keys are also available.

• If the number entered

is not on the disc, the

entry will have no effect.

Re-enter the correct

number.

• For more details, refer

to the disc operation

information.

Unit is in DVD mode, press DVD.

Check List

40

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

40

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Detailed Descriptions of Each On-Screen Display

SELECT :

SET : SET NEXT : DISPLAY

T I TLE : 1 DVD

CHAPTER : 12 1 : 12 : 55

3

4

SET : SET NEXT : DISPLAY

TRACK : 1 V IDEO CD

PBC : OFF 1 : 35 : 12

C

D

DVD Operation using On-Screen Displays (continued)

NUMBER

keys

Disc information screen (for DVD)

• Track No. and elapsed playing time are not displayed during

play started from menu of Video CDs with playback control.

• When

appears on the screen while a button is being pressed,

it means that the corresponding operation is prohibited by the

unit or the disc.

Disc information screen (for Video CD/ CD)

Notes

A. Track No.

• Select “TRACK,” and press SET.

• Change the No. by pressing or NUMBER keys, and

press SET.

B. Playback control ON/OFF

[Video CD with playback control only]

ON Video CD menu play is displayed.

OFF Video CD menu play is not displayed.

C. Disc currently being played

Video CD CD

D. Elapsed playing time

1. TITLE No.

• Select “TITLE,” and press SET*.

• Change the No. by pressing or NUMBER keys, and

press SET.

2. Chapter No.

• Select “CHAPTER,” and press SET.

• Change the No. by pressing or NUMBER keys, and

press SET.

3. Disc currently being played

4. Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press SET.

• Change the elapsed time by pressing NUMBER keys.

Hours

➞

Minutes

➞

Seconds are entered in order.

If the time entered is not on the disc, the entry will have

no effect.

Re-enter the correct time.

e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

Hour Minutes Seconds

• This function does not work with some discs.

1

2

A

B

SELECT

SET

SELECT :

SET : SET NEXT : DISPLAY

T I TLE : 1 DVD

CHAPTER : 12 1 :

--

:

--

If SET is pressed while

making entries, unit returns

to the condition before

entries were made.

4141

Advanced Operation

SET : SET END : DISPLAY

PLAY

REPEAT : CHAPTER

SET : SET END : DISPLAY

PLAY

REPEAT : DISC

RANDOM PLAY

TITLE

chapter

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

•

CHAPTER/TITLE REPEAT PLAY (DVD)

•

TRACK/DISC REPEAT PLAY (Video CD/CD)

For your reference

a. Repeat Play

Detailed Descriptions of Each On-Screen Display

*

Important:

I

f a remote control button does not work when pressed, press the DVD button on the

remote and try the button again.

b. Play mode [Video CD/ CD only] (See page 37 or 38.)

a

b

track

TRACK REPEAT

DISC REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

DVD CHAPTER REPEAT TITLE REPEAT REPEAT OFF

Video CD/CD TRACK REPEAT DISC REPEAT REPEAT OFF

PROGRAM PLAY program play

RANDOM PLAY random play

---- normal play

Unit information screen

• Select “REPEAT,” and press SET.

• Change the desired mode during play by pressing , and press SET.

42

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

42

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

MP3/WMA/JPEG Playback Operation

PLAY

PLAY MODE : NORMAL

00

:

00

:

00

ROOT

. .

My favorite

CAR1

TECHNO

CAR2

POPS

END

_

W

ALTZ

J

AZZ

PICTURES

1

Press POWER* on the

remote or unit.

Press OPEN/CLOSE, and

then place an

MP3/WMA/JPEG disc into

the disc tray. Press

OPEN/CLOSE to close.

2

This unit can play MP3/WMA/JPEG

format CD-R or CD-RW recorded for

personal use on a PC, etc.

Some discs may not play due to

recording condition.

3

• MP3/WMA/JPEG menu

is displayed.

• Playback starts

automatically (except

JPEG ﬁ les).

• CD directory is displayed.

ROOT

My favorite

TECHNO

POPS

J

AZZ.wma

CAR1.jpg

CAR2.jpg

END

_

W

ALTZ.mp3

PICTURES

picture1.jpg

picture2.jpg

picture3.jpg

picture4.jpg

Function

Status

Counter

PLAY MODE

Folder area

(Current folder

appears green.)

File area

(Selected

ﬁ le/folder is

highlighted.

Titles are

displayed up to

11 characters.)

:MP3 ﬁ le :WMA ﬁ le

:JPEG ﬁ le

:Folder

:Parent folder

Press to select the desired

PLAY MODE.

Press to move cursor to

File area or PLAY MODE.

(In STOP mode)

4

Select an MP3/WMA ﬁ le ( / ).

MP3/WMA Playback (See next page)

Select a Parent folder (

).

Make changes to the previous

directory display.

Select a folder ( ).

Display ﬁ les/folders contained in the

folder.

Select an JPEG ﬁ le (

).

JPEG Playback (See next page)

5

Press ACTION to return to

the DVD MAIN MENU.

(Press ACTION again to

return to the

MP3/WMA/JPEG MENU.)

PLAY

MODE:

MP3/WMA Playback

JPEG Playback

- Slide-show -

NORMAL

All MP3/WMA ﬁ les are

selected and played back

one time only.

All JPEG ﬁ les are selected

and played back one time

only.

SINGLE

REPEAT

The selected MP3/WMA ﬁ le

is played back repeatedly.

The selected JPEG ﬁ le is

played back repeatedly.

FOLDER

REPEAT

The MP3/WMA ﬁ les

contained in the selected

folder are played back

repeatedly. However, folders

below the selected folder are

not played back.

The JPEG ﬁ les contained in

the selected folder are played

back repeatedly.

However, folders below the

selected folder are not played

back.

DISC

REPEAT

All MP3/WMA ﬁ les are played

back repeatedly.

All JPEG ﬁ les are played

back repeatedly.

PLAY MODE selection

Press to select items and SET

or PLAY to start.

MP3/WMA/JPEG MENU SCREEN

Windows Media, and the Windows logo are trademarks,

or registered trademarks of Microsoft Corporation in the

United States and/or other countries. WMA is a

compression format developed by Microsoft Corporation.

It achieves the same sound quality as MP3 with a ﬁ le size

that is smaller than that of MP3.

Example: If the CD-R/CD-RW

ﬁ le hierarchy is displayed on the

PC as shown in diagram at left,

MP3/WMA/JPEG Menu Screen,

like the one below is displayed.

• File names are displayed in

ascending order (1, 2, 3...9, A, B,

C...Y, Z) in the MP3/WMA/JPEG

MENU Screen ROOT.

■

File area Operation

(In STOP mode)

■

Play mode Operation

(In STOP mode)

Explanation of Icons

MPEG Layer-3 audio decoding technology licensed from

Fraunhofer IIS and Thomson multimedia.

Press SKIP+

|

(next) or

SKIP-

|

(previous) to skip a

ﬁ le/folder page (7ﬁ les) in the File

area.

Note

4343

Advanced Operation

SELECT

SET

POWER

OPEN/

CLOSE

ANGLE

PLAY

ZOOM

SKIP+

|

STOP

PAUSE

SKIP-

|

ACTION

MP3/WMA Playback

JPEG Playback

Press to select an JPEG ﬁ le (

)

.

Press SET or PLAY. Selected ﬁ le is

displayed.

1

2

■

Next/Previous Search

Press SKIP+

|

or SKIP-

|

JPEG Playback Screen

<Example: CAR1>

Do steps 1~3 on page 42.

Press ACTION to return to the DVD MAIN

MENU.

3

■

Start Slide-show

Press SEARCH/SLOW or

SEARCH/SLOW .

(see next page)

■

Enlarging an image

Press ZOOM. (see next page)

■

Rotating an image

Press ANGLE. (see next page)

■

Returned on the MP3/WMA/JPEG MENU

Press STOP. (see previous page)

PLAY

PLAY MODE : NORMAL

00

:

00

:

00

ROOT

. .

My favorite

CAR1

TECHNO

CAR2

POPS

END

_

W

ALTZ

J

AZZ

PICTURES

ROOT

My favorite

CAR1.jpg

CAR2.jpg

END

_

W

ALTZ.mp3

PICTURES

picture1.jpg

SKIP+

|

SKIP-

|

<Example: CAR1> <Example: CAR2>

Only the JPEG

ﬁ les in a folder that

were saved while

being displayed

are displayed.

You can play JPEG images.

Displayable Image Size: 32x32~7680x7680 pixels

• Some JPEG format may not be played back.

■

Forward/ Reverse Search

Press SEARCH/SLOW or

SEARCH/SLOW during play.

Press PLAY to release.

• Search speed, slow at ﬁ rst, increases with

each additional press of the button up to 5

levels.

■

Forward/ Reverse Track Skip

Press SKIP+

|

or SKIP-

|

during play.

Each press skips a track.

• If pressed within ﬁ rst 3 seconds of playback,

skips to the previous track. If over 3 seconds,

returns to top of track. (SKIP-

|

only.)

• Put unit in Stop mode before performing

folder/ﬁ le selection (see step 4 on previous

page.)

■

Pause

Press PAUSE during play.

Press PLAY to release.

Press SET or PLAY to start playback.

2

3

4

Press OPEN/CLOSE to eject the disc.

The MP3 MENU is closed automatically.

Press STOP to stop play.

• Copyright protected ﬁ les and ﬁ les containing errors

cannot be played back. The unit skips to the next ﬁ le.

Press to select an MP3/WMA ﬁ le

(

/ ) in STOP mode.

1

Do steps 1~3 on page 42.

Note

SEARCH/

SLOW

SEARCH/

SLOW

44

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

44

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

MP3/WMA/JPEG Playback Operation (continued)

■

Still picture

Press PAUSE (only SLIDE)

■

Forward/Reverse Track Skip

Press SKIP+

|

or SKIP-

|

. Each press

skips a ﬁ le.

■

Cancel slide show

Press STOP to return to the MP3/WMA/JPEG

MENU.

(During JPEG Playback.)

JPEG ﬁ les are displayed automatically (about

every 3 seconds) as a slide-show.

Image changes every 3 seconds.

JPEG Playback - Slide-show -

Press

SEARCH/SLOW

or

SEARCH/SLOW

.

1

SEARCH/

SLOW

SEARCH/

SLOW

Press ACTION to return to the DVD MAIN

MENU.

2

(During JPEG Playback.)

You can enlarge speciﬁ c portions of a JPEG

picture and select the zoom ratio using the ZOOM

button on the remote during JPEG Playback.

Set Zoom size.

Press ZOOM repeatedly to change display as

follows.

Press STOP to return to the MP3/WMA/JPEG

MENU.

• You can enlarge the center portion of the image to

one of 2 magniﬁ cations.

• Operation can be done during Rotation (below).

■

Use the , , and buttons to move the

position up, down, left and right.

JPEG Playback - Zoom -

JPEG Playback - Rotation -

(During JPEG Playback.)

You can rotate a JPEG picture using the ANGLE

button on the remote during JPEG Playback. (The

JPEG picture will be rotated 90° clockwise.)

Set rotation.

Press ANGLE repeatedly to change display

as below. (During JPEG Playback screen)

Press STOP to return to the MP3/WMA/JPEG

MENU.

1st

Press

2nd

Press

3rd

Press

ROOT

My favorite

TECHNO

CAR1.jpg

CAR2.jpg

END

_

W

ALTZ.mp3

PICTURES

picture1.jpg

picture2.jpg

picture3.jpg

picture4.jpg

X 1.0 (ORIGINAL)

3rd press

X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)

1st press

2nd press

Image changes every 3 seconds.

picture 1 picture 2 picture 3 picture 4

picture 3 picture 2 picture 1

• Operation can be done during ZOOM (above).

• The vertical/horizontal ratio of rotated JPEG

images may vary when they are displayed.

• Position cannot be changed on X1.0 ORIGINAL

images.

If SEARCH/SLOW is pressed while picture 1 is

displayed.

If SEARCH/SLOW

is pressed while picture 3 is

displayed.

Only the JPEG ﬁ les in a folder that were saved

while being displayed are displayed.

4th

Press

Note

Notes

4545

Advanced Operation

1

1) Press to select

“DVD LOCK.”

2) Press SET to set “ON”

or “OFF.”

DVD Lock Ratings (DVD only)

■ “ON”

➞

DVD Lock is activated.

■ “OFF”

➞

DVD Lock is deactivated.

LEVEL 1: LOCK ALL:

Playback of all DVDs, CDs and Video CDs

is prohibited. (Use to prohibit play of

mature theme DVDs not encoded with a

rating level.)

LEVEL 2: DVDs expressly for children can be played

back.

LEVEL 3 to 7: DVDs for general audiences/children can

be played back. (DVDs with mature

content are prohibited.)

LEVEL 8: NO LIMIT: (Factory preset)

All DVDs can be played back.

You can prevent playback of DVDs with a speciﬁ c rating level which may be unsuitable for children.

• Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback

will be prohibited.

After DVD Lock is set and a blocked DVD

is played, this message will appear. The

message may differ depending on the

disc.

To continue viewing a blocked

program for now,

Press

to select “YES” and SET.

Then, enter your 4-digit secret code.

When “NO” is selected, blocked programs

cannot be viewed.

• Ratings which are highlighted in Green will be blocked; those

not highlighted (white letters) will not be blocked.

Perform DVD Lock setting in TV mode.

Enter your secret code to display LOCK menu.

(Perform “Enter Secret Code” steps on page 28.)

US MOV

I

ES

:

O

FF

CHANGE

SET

T

I

NGS

US

TV

PROGRAMS

:

O

FF

CHANGE

SET

T

I

NGS

DVD

LOCK

:

O

FF

CHANGE

SET

T

I

NGS

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

LOCK

SELECT :

SET : SET END : DISPLAY

,

YOUR SELECTION EXCEEDS THE

PLAYER S RATING LIMIT.

DO YOU WANT TO CHANGE THE

LIMIT?

YES

NO

Discs not encoded with a rating level will play even if the jacket states it is for mature audiences.

For these discs, the DVD Lock Ratings will not work.

Caution

2

1) Press to select

“CHANGE SETTINGS.”

2) Press SET to display

screen.

US MOV

I

ES

:

O

FF

CHANGE

SET

T

I

NGS

US

TV

PROGRAMS

:

O

FF

CHANGE

SET

T

I

NGS

DVD

LOCK

:

O

FF

CHANGE

SET

T

I

NGS

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

LOCK

3

1) Press to select

rating level.

2) Press SET to select

“LOCKED” or

“UNLOCKED.”

LOCK ALL

SELE

C

T

:

SET

:

SET

END

:

ACT

I

O

N

1

2

3

4

5

6

7

8

UNLOCKED

4

Press ACTION three times to exit.

To change DVD LOCK settings

After entering your secret code in

step 3 on page 28, select “OFF” to

deactivate DVD Lock or change

the rating level.

DVD Lock Feature

*

Important:

If a remote control button does not work when

pressed, press the FM/TV, DVD button on the

remote and try the button again.

ACTION

PROGRAM RATING EXCEEDED

SELECT

SET

46

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

46

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

DISC LANGUAGES (DVD only)

To select and set the language of the audio soundtrack,

subtitles, or title/DVD menus for all discs to be played.

“AUDIO” selections

To select the audio soundtrack language.

(Factory preset: English)

English/Spanish/French/Japanese

Original: Original disc language

OTHER

✱✱✱✱

: Other language selection*

1

“SUBTITLE” selections

To select the subtitle language.

(Factory preset: AUTO)

AUTO: Same language selected for “AUDIO”

• If language set for “AUDIO” is

used in playback, subtitles will not

appear.

• If another language is used during

playback, the subtitles will appear

in the language selected at “AUDIO”

setup.

English/Spanish/French/Japanese

OTHER

✱✱✱✱

: Other language selection*

1

“MENUS” selections

(Factory preset: English)

To select the language used in title menus or

DVD menus.

English/Spanish/French/Japanese

OTHER

✱✱✱✱

: Other language selection*

1

To enter OTHER ✱✱✱✱ code number,

Press NUMBER keys (Please refer to

language codes on page 49).

To make corrections, press

repeatedly to

delete language code number, and correct.

1

3

Once initial settings are done, they remain

in memory (even after the power is off) until

changed. This means the unit will always

operate under the same conditions (especially

DVDs) each time.

DISC LANGUAGES (See below.)

Any languages offered on the disc can be set. If a

language not offered is set, the original disc language

will be selected.

AUDIO OUTPUT (See page 47.)

You can set the audio output that comes from the

digital audio output terminal.

STILL MODE (See page 48.)

To select “FIELD” or “FRAME” to prevent jitter or to

make small text or ﬁ ne patterns clearly visible in a still

picture. When “AUTO” is set, “FIELD” or “FRAME” is

selected automatically.

TV MODE (See page 48.)

To select whether the video material for a wide-screen

will be played back in Pan & Scan style or in Letterbox

style.

4

1) Press to

select “DISC

LANGUAGES.”

2) Press SET to

display screen.

Press ACTION* in Stop mode to display

MAIN MENU.

1) Press to

select an item.

2) Press SET to set.

2

1) Press to

select “DVD.”

2) Press SET to

display screen.

1) Press to

select an item.

2) Press SET

repeatedly for

desired language.

(Please refer right.)

5

6

Press ACTION to redisplay DVD MAIN

MENU and go to step 3 to setup another item.

Or, press ACTION three times to exit.

*

1

If the selected language is not offered, the

original disc language is selected.

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

ST I L L MODE : AUTO

TV MODE :

4:3 Pan & Scan

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

ST I L L MODE : AUTO

TV MODE :

4:3 Pan & Scan

M

A

I

N

M

EN

U

DVD

LOCK

CH

C

L

OC

K

TV

LANGUAGE

END :

ACT

I

O

N

SE

L

E

C

T

:

SET

:

SET

5

3

1

Settings for DVD Operation

DISC LANGUAGES

SELECT :

SET : SET

END : ACTION

AUDIO : English

SUBT I TLE : AUTO

MENUS : English

Unit is in TV mode, press FM/TV.

Check List

4747

Advanced Operation

*

Important:

If a remote control button does not work when pressed, press the FM/TV, DVD button

on the remote and try the button again.

• Make settings according to ampliﬁ er

connected to optical audio output as shown

in above table.

*1 When connecting an ampliﬁ er (with an

optical digital input connector) which

does not contain the Dolby Digital or

dts decoder, be sure to select “PCM.”

If “Bitstream” is selected, starting DVD

play may cause such a high level of noise

as to be harmful to your ears and damage

the speakers.

*2 When a dts decoder is connected, please

select “Bitstream” in “dts.” If “PCM” is

selected, there will be stereo sound.

AUDIO OUTPUT

Select the digital output to be output from the optical

digital audio output connector of the unit.

Do steps 1 and 2 on page 46.

■ “LPCM (DVD)” selections

OFF: Linear PCM of less than 48 kHz/16 bit

is output. When playing DVDs recorded

in linear PCM of over 48 kHz/20 bit, no

digital audio is output. (Factory preset)

PCM: When playing DVDs recorded in

linear PCM of 48 kHz/20 bit/24 bit or

more, digital audio converted to 44.1

kHz/16 bit or 48 kHz/16 bit is output.

(Digital output of PCM audio is restricted

to48 kHz/16 bit or below for copyright

protection.)

■ “Dolby Digital” selections

Bitstream: Dolby Digital bitstream (1ch-5.1ch) is

output. (Factory preset)

PCM: When you have connected a ampliﬁ er

that doesn’t have a built-in Dolby Digital

decoder.

■ “dts” selections

Bitstream: dts bitstream is output. (Factory preset)

PCM: When you have connected a ampliﬁ er

that doesn’t have a built-in dts decoder.

■ “DRC (Dynamic Range Compression)”

selections

OFF: Normal audio range is selected. (Factory

preset)

ON: For dynamic sound even at low volume,

this is useful for late-night listening.

[Dolby Digital DVDs only].

1) Press to

select an item.

2) Press SET

repeatedly for

output. (See

below.)

1) Press to

select “AUDIO

OUTPUT.”

2) Press SET to

display screen.

1

3

2

4

Press ACTION to redisplay DVD MAIN MENU

and go to step 2 to setup another item. Or,

press ACTION three times to exit.

AUDIO OUTPUT

SELECT :

SET : SET

END : ACTION

LPCM(DVD) : OFF

Dolby Digital : Bitstream

dts : Bitstream

DRC : OFF

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

ST I L L MODE : AUTO

TV MODE :

4:3 Pan & Scan

Type of

ampliﬁ er

to be

connected

Recommended setting

LPCM

(DVD)

Dolby

Digital

dts

No ampliﬁ er

is connected

AV ampliﬁ er

without Dolby

Digital/dts

decoder

PCM PCM*

1

PCM*

1

AV ampliﬁ er

including

Dolby Digital

decoder

PCM Bitstream PCM

AV ampliﬁ er

including

Dolby

Digital/dts

decoder

PCM Bitstream Bitstream*

2

ACTION

SELECT

SET

48

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

48

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

STILL MODE

1

1) Press * to select

“STILL MODE.”

2) Press SET repeatedly

for mode. (See below)

2

Do steps 1 and 2 on page 46.

AUTO: “FIELD” (Field still) or “FRAME” (Frame still)

is automatically selected during the still mode.

(Factory preset)

FIELD: “FIELD” (Field still) is always selected.

This setting will reduce jitter when compared

with “AUTO” on some discs.

FRAME: “FRAME” (Frame still) is always selected.

Some texts and ﬁ ne patterns will be seen clearly

when compared with “AUTO” on some discs.

Selecting TV MODE

a

1) Press to select “TV

MODE.”

2) Press SET repeatedly

for mode. (See below.)

b

Do steps 1 and 2 on page 46.

4:3 Pan & Scan : Widescreen video data is played in Pan

& Scan style (left and right of screen is

trimmed.)

• Video data not formatted in Pan &

Scan will play in letterbox style.

4:3 Letterbox : Widescreen video data is played in

Letterbox style (top and bottom of

screen has black margin).

Set the screen display style for widescreen video material

playback.

4:3 Pan & Scan (Factory preset)

4:3 Letterbox

Set to reduce jitter in a displayed still picture or a motion

picture.

3

Press ACTION twice to exit this mode.

c

Example

(Factory preset)

*

Important:

If a remote control button does not

work when pressed, press the DVD

button on the remote and try the

button again.

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

ST I L L MODE : AUTO

TV MODE :

4:3 Pan & Scan

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

ST I L L MODE : AUTO

TV MODE :

4:3 Pan & Scan

Settings for DVD Operation (continued)

ACTION

SELECT

SET

4949

Advanced Operation

Code Language

6565

Afar

6566

Abkhazian

6570

Afrikaans

6577

Ameharic

6582

Arabic

6583

Assamese

6588

Aymara

6590

Azerbaijani

6665

Bashkir

6669

Byelorussian

6671

Bulgarian

6672

Bihari

6678

Bengali;Bangla

6679

Tibetan

6682

Breton

6765

Catalan

6779

Corsican

6783

Czech

6789

Welsh

6865

Danish

6869

German

6890

Bhutani

6976

Greek

6978

English

6979

Esperanto

6983

Spanish

6984

Estonian

6985

Basque

7065

Persian

7073

Finnish

7074

Fiji

Code Language

7678

Lingala

7679

Laothian

7684

Lithuanian

7686

Latvian, Lettish

7771

Malagasy

7773

Maori

7775

Macedonian

7776

Malayalam

7778

Mongolian

7779

Moldavian

7782

Marathi

7783

Malay

7784

Maltese

7789

Burmese

7865

Nauru

7869

Nepali

7876

Dutch

7879

Norwegian

7982

Oriya

8065

Panjabi

8076

Polish

8083

Pashto, Pushto

8084

Portuguese

8185

Quechua

8277

Rhaeto-Romance

8279

Romanian

8285

Russian

8365

Sanskrit

8368

Sindhi

8372

Serbo-Croatian

8373

Singhalese

Code Language

7079

Faroese

7082

French

7089

Frisian

7165

Irish

7168

Scots Gaelic

7176

Galician

7178

Guarani

7185

Gujarati

7265

Hausa

7273

Hindi

7282

Croatian

7285

Hungarian

7289

Armenian

7365

Interlingua

7378

Indonesian

7383

Icelandic

7384

Italian

7387

Hebrew

7465

Japanese

7473

Yiddish

7487

Javanese

7565

Georgian

7575

Kazakh

7576

Greenlandic

7577

Cambodian

7578

Kannada

7579

Korean

7583

Kashmiri

7585

Kurdish

7589

Kirghiz

7665

Latin

Code Language

8375

Slovak

8376

Slovenian

8377

Samoan

8378

Shona

8379

Somali

8381

Albanian

8382

Serbian

8385

Sundanese

8386

Swedish

8387

Swahili

8465

Tamil

8469

Telugu

8471

Tajik

8472

Thai

8473

Tigrinya

8475

Turkmen

8476

Tagalog

8479

Tonga

8482

Turkish

8484

Tatar

8487

Twi

8575

Ukrainian

8582

Urdu

8590

Uzbek

8673

Vietnamese

8679

Volapük

8779

Wolof

8872

Xhosa

8979

Yoruba

9072

Chinese

9085

Zulu

Enter the appropriate code number for the initial settings “AUDIO,” “SUBTITLE” and/or “MENUS” (see

page 46).

Language Code List

50

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

50

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Check the following points once again if you are having trouble with your unit.

Before Requesting Service

Power Correction

No power…

• Completely insert Power Plug into an AC outlet.

• Set POWER button to ON.

Power turns itself

off...

• Auto power-off (shut off) occurs after about 5 min. in DVD mode with

no operation, or if there is no broadcast signal in TV mode. Turn the

power back on. (P. 17, 26)

Monitor Correction

No picture or sound...

• Make sure your antenna system (TV or CABLE), is correctly set.

(P. 10)

• Completely insert Power Plug into an AC outlet.

• Set POWER button to ON.

Poor picture with

normal sound...

• Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the

SET UP Video Adjustment. (P. 33)

Poor sound with

normal picture...

• Adjust VOLUME control. (P. 18)

Poor TV reception...

• Adjust SHARPNESS and PICTURE controls in the SET UP Video

Adjustment. (P. 33)

No color or poor

color...

• Adjust TINT and COLOR controls in the SET UP Video Adjustment.

(P. 33)

Ghost (multiple)

images...

• Install a directional antenna.

TV programs cannot

be watched...

• Make sure the selected channel is in unit’s memory. (P. 12)

Remote Control Correction

Unit cannot be

controlled...

• Aim Remote directly at the remote sensor on the unit. (P. 9)

• Avoid any object blocking signal path.

• Inspect the remote batteries. (P. 4)

• Exposing unit remote sensor to direct ﬂ uorescent or outdoor light may

cause signal interference.

ACTION, SELECT,

SET POWER, etc.

buttons cannot be

selected...

• Press FM/TV for TV mode. (P. 18)

• Press DVD for DVD mode. (P. 16)

• Press FM/TV for FM mode. (P. 24)

• Check remote batteries.

5151

For Your Information

If you cannot resolve the problem, please call the Customer Satisfaction Center for product

assistance at 1-800-211-PANA(7262).

To locate an authorized servicenter call toll free 1-800-211-PANA(7262)

or send e-mail to : [email protected].

DVD/Video CD/

CD

Correction

Play fails to start

even when PLAY is

pressed...

• This unit cannot play discs other than DVDs, Video CDs and CDs.

• The disc may be dirty and require cleaning.

Play starts but then

stops

immediately...

• Be sure disc is installed with label side up.

Picture is distorted

during rapid advance

or rapid reverse...

• The picture will be somewhat distorted at times: this is normal.

No Forward/Reverse

search play...

• Some discs may have sections which prohibit Forward/Reverse

search. (P. 17)

Play does not start

even when title is

selected...

• Conﬁ rm the “DVD LOCK” setting. (P. 45)

Audio soundtrack

and/or subtitle

language is not the

one selected at the

initial settings...

• If the audio soundtrack and/or subtitle language selected at DVD

initial settings does not exist on the disc, it will not be accessible.

No subtitles...

• Subtitles appear only when available on disc.

• Select “ON” at the “Subtitle language” section (P. 34) to display

subtitles.

Alternative audio

soundtrack

(or subtitle) language

cannot be selected...

• Alternative language cannot be selected with discs which do not

contain more than one language.

• For some discs, alternative language cannot be selected with the

AUDIO or SUB TITLE button. Try selecting it from the DVD MAIN

MENU if available.

Angle cannot be

changed...

• This function is dependent on software availability. Even if disc has

multiple angles, they may be recorded for speciﬁ c scenes only (ANGLE

Indicator on unit lights up). (P. 35)

Miscellaneous Correction

The disc cannot be

removed...

• First, unplug unit. Then, prepare a rigid wire (e.g. an extended paper

clip, etc.) and, applying moderate force, insert it straight into the hole

at the base of the tray. The tray will eject a little. Now, pull the tray all

the way out and remove the disc. (P. 7)

52

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

52

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

These displays will alert you of a missed operation or provide further instructions.

Warning and Instruction Displays

OSD Caution

PLEASE SET CLOCK

BEFORE TIMER

SETTING

If you attempt to set the On-Timer and the Clock is not set... (P.12)

PLEASE CHECK

THE DISC, AND

FOR STAINS OR

SCRATCHES ON

DISC

If you press PLAY, or the unit reads data from a stained or scratched

disc in DVD mode. Also, if the type of disc is other than DVD, Video CD

or CD... (P.6)

THIS DISC MAY NOT

BE PLAYED IN YOUR

REGION

Playback of a disc with different region number was attempted. Only

discs marked region “1,” “ALL,” or those that include “1” are playable on

this unit. (P.3)

THIS TYPE OF DISC

CANNOT BE PLAYED.

PLEASE INSERT A

DIFFERENT DISC

An unusable disc is inserted in the unit. (P.6)

CANNOT PLAY THIS

FILE

This ﬁ le format cannot be played.

(Appears during MP3/WMA/JPEG ﬁ le playback)(P.42)

THIS FILE IS

PROTECTED

This ﬁ le is copyright protected and cannot be played back.

(Playback is prohibited.)(P.42)

5353

For Your Information

■ Conexión para Ant./Cable

Conecte Ant./Cable a la entrada de antena de la

TV (VHF/UHF).

Conecte por favor todas las conexiones del cable o de la antena antes de energizar los aparatos.

1

Conecte el cable electrico de la unidad

en el enchufe de pared de la CA.

Realizando Conﬁ guración Inicial

2

Encienda la TV

mediante el

control o

directamente en

la unidad. La

unidad inicia la

busqueda de

canales y ajusta

el tiempo

automaticamente.

■ Conexión para Sistema Digital de

Satelite (DSS)/Convertidor de cable

Conecte la salida del convertidor de cable la

entrada “VFH/UHF” con el RF cable.

Presione FM/TV para la modalidad TV.

3

Selecciones se

realizaran

automaticamente,

cuando la

conﬁ guracion

termine la pantalla

2

/

6

/

2003

THU

12

:

00

P

M

DST

:

O

N

A

UTO

C

L

OCK SET

CO

M

P

L

ETED

SETT

I

N

G

:

CH

1

0

PLEASE

SET

CLOCK BY

P

R

ESS

I

NG

ACT

I

ON

KEY

A

UTO

C

L

OCK SET

I S I NCO

M

P

L

ETE

Spanish Quick Use Guide/Guía para rápida consulta

• Si usa convertidor de cable, enciendala y seleccione

el Servicio Publico de Canales de Television (PBS) en

su horario de uso o tiempo de su zona. Si utiliza

receptor DSS este debe de estar apagado.

• Si “AUTO CLOCK

SET IS

INCOMPLETE”

aparece en pantalla,

coloque el tiempo

usando el

procedimiento manual

(MANUAL CLOCK

SET), vealo

enseguida.

• Los botones de funciones son inoperantes durante la

Conﬁ guración inicial.

• Dependiendo de las condiciones, puede que el Ajuste

automático del reloj tarde más de 30 minutos. En ese

caso, pulse STOP para detener la conﬁ guración y

realice los ajustes manualmente. (Vea la p.12-13 de

Libro de operaciones avanzadas).

Nota

VHF/UHF

Ant./Cable

VHF/UHF

Ant./Cable

Convertidoe de cable

VHF/UHF

Conectando

CH AUTO SET PROCEEDING

PROCEEDING

AUTO CLOCK SET

CANCEL : PRESS STOP KEY

54

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

54

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Spanish Quick Use Guide/Guía para rápida consulta

Presione dos veces la tecla

ACTION para poner el RELOJ en

marcha y salir.

Presione ▲▼ para seleccionar el

mes y SET para colocarlo. De la

misma forma, seleccione y ajuste

la fecha, año, hora y DST (Hora de

Verano).

Ajustar de nuevo el reloj

1

Presione ACTION para visualizar el

menú.

2

Presione

▲▼◄ ► para

seleccionar

“RELOJ,” y

luego Presione

SET.

3

Presione ▲▼

para

seleccionar

“MANUAL” y

luego presione

SET.

4

Presione ▲▼ y

SET para

seleccionar y

ajustar la hora y

la fecha.

5

Presione ACTION dos veces para

que el reloj comience a funcionar

y

salir de este modo.

Ajuste Manual del Reloj

1

Si el ajuste automático del reloj no se ha

completado, ajuste el reloj manualmente de la

siguiente manera.

2

3

5

3

1

MENU PR

I

NCIPAL

DVD

BLOQUEO

CANAL

RELOJTV

ID

I

OMA

TERM

I

NAR :

ACT

I

O

N

ELEG

I

R

:

F

I

JAR

:

SET

FIJACION AUTOMATICA

M

A

NU

AL

AJUSTE ZONA HORA

:

0

ELEGIR :

FIJAR : SET

TERMINAR : ACTI ON

FIJAR RELOJ

Presione ACTION en el control

remoto para visualizar la pantalla

del menú RELOJ.

FIJAR RELOJ

VERANO

:

ACT

2 / 6/

:

2003

JUE

12

00

PM

ELEGIR HORA

ELEGIR:

FIJAR : SET

I NIC IAR : ACTI ON

RETROCEDER:

5555

For Your Information

■

Para buscar una escena en particular

Búsqueda hacia adelante

Presione SEARCH/SLOW

en el modo de

reproducción.

Búsqueda hacia atrás

➞

Presione SEARCH/SLOW

en el modo de

reproducción. (Para liberar, presione PLAY)

■

Para saltar un capítulo o una pista Salto

hacia adelante

Presione SKIP+

l en el modo de

reproducción. Un capítulo (DVD) o una pista

(Vídeo CD/CD) se salta cada ves que se

oprime la tecla.

Salto hacia atrás

➞

Presione SKIP- l

en el modo de

reproducción.

■

Para ver una imagen ﬁ ja

Presione PAUSE durante la reproducción. (Para

liberar, presione PLAY)

■

Para ver imágenes cuadro a cuadro

(DVD/Vídeo CD)

Presione PAUSE en el modo de imagen ﬁ ja.

La imagen avanza un cuadro cada vez que

presiona la tecla. (Para volver a la reproducción

normal, presione PLAY.)

■

Para ver en cámara lenta

(DVD/Vídeo CD)

Presione SEARCH/SLOW

o SEARCH/SLOW

en el modo de imagen ﬁ ja. (Para liberar,

presione PLAY)

1

2

3

4

5

6

Presione POWER en el control remoto o

el aparato y luego el boton DVD.

Introducir un disco.

1) Presione OPEN/CLOSE.

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus

superﬁ cies, póngalo con el lado donde esté

impreso el título hacia arriba, alinéelo con las

guías y póngalo en su posición apropiada.

Disco de 3”(8 cm) Disco de 5” (12 cm)

Presione PLAY para Iniciar la

reproducción. La bandeja del disco se

cierra automáticamente.

• Si está usando un DVD interactivo (Interactive

DVD) o un Vídeo CD con contol de reproducción

(playback control) y aparece un menú de títulos

(TITLE MENU) en la pantalla, siga al paso 4.

Presione OPEN/CLOSE para expulsar el

disco.

1) Presione ▲▼◄ ► o las teclas

numéricas para seleccionar el

artículo deseado.

2) Presione SET para la reproducción.

Si usa las teclas numéricas,

la reproducción comienza

automáticamente.

Presione STOP para parar la

reproducción.

Operaciones básicas del DVD

1

Cambio del idioma de subtítulos

[DVD solamente]

EI idioma de los subtítulos seleccionado al hacer

las ﬁ jaciones iniciales se puede cambiar por otro

idioma diferente, si éste se encuentra disponible.

Presione SUB TI TLE

durante la

reproducción.

• Cuando no haya

subtítulos grabados, “-”

se visualizará en lugar

del número de idioma.

2

1

Presione AUDIO

durante la

reproducción para

visualizar la pantalla

AUDIO.

EI idioma de la pista de sonido seleccionado al

hacer las ﬁ jaciones iniciales se puede cambiar

por otro idioma diferente, si éste se encuentra

disponible.

2

Presione ▲▼ para

seleccion el idioma

deseado.

Cambio del idioma de la pista de sonido

[DVD solamente]

SUBTITULO : 1 ENG ACTIVO

I love you

ELEGIR :

ACTIVO/INACTIVO :

TERMINAR : SUB TITLE

SUBTITULO : 3 ESP ACTIVO

Te amo

ELEGIR :

ACTIVO/INACTIVO :

TERMINAR : SUB TITLE

SONIDO: 1 ENG

Dolby Digital 3/2.1ch

Hello

ELEGIR :

TERMINAR : AUDIO

SONIDO: 3 ESP

Dolby Digital 3/2.1ch

Hola

ELEGIR :

TERMINAR : AUDIO

1) Presione ▲▼ para

seleccionar el

idioma deseado.

2) Presione ► (o ◄)

para seleccionar

“ACTIVO” o

“INACTIVO.”

56

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

56

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Spanish Quick Use Guide/Guía para rápida consulta

1

2

Presione AUDIO durante la reproducción

para visualizar la pantalla AUDIO.

1) Presione ▲▼ (o ◄►)

para seleccionar el

ajuste deseado.

2) Presione ► (o ◄)

para ajustar. (DVD

solamente)

Selección de vocal para los discos de Karaoke

[DVD/Video CD]

Durante la reproducción de un DVD, puede ampliar a

imagen seleccionando la relación de zoom usando el

botón ZOOM mediante control remoto.

Seleccione el tamaño de la imagen.

Presione ZOOM repetidamente para cambiar el

tamaño de la imagen como se indica a continuación:

■

Use los botones

, , y para desplazar

la posición hacia arriba, hacia abajo, hacia la

izquierda o hacia la derecha.

1

Presione ANGLE

durante la

reproducción para

visualizar la pantalla

de ángulo.

Algunos discos DVD tienen escenas que han sido ﬁ lmadas

simultáneamente desde un número de ángulos diferentes.

Con estos discos, la misma escena podrá verse desde

cada uno de estos ángulos diferentes utilizando el botón

ANGLE.

2

Presione ▲▼ para

seleccionar el ángulo

deseado.

Visión desde otro ángulo [DVD solamente]

Ampliación de la imagen [DVD solamente]

Algunos discos con películas, por ejemplo,

vienen con dos o más títulos. Si el disco tiene

un menú de títulos grabados, el botón TITLE

podrá utilizarse para seleccionar el título de la

película.

1

2

Presione TITLE durante la

reproducción. Ahora se visualiza una

lista de los títulos del disco.

1) Presione

▲▼◄ ►

o las

teclas numéricas

para seleccionar

el título deseado.

2) Presione SET o

PLAY.

Utilización de un menú de títulos

[DVD solamente]

1

Algunos discos DVD tienen estructuras

únicas de menús llamadas menús DVD.

Por ejemplo, los DVDs programados con un

contenido complejo proporcionan menús guía,

y los grabados con varios idiomas proporcionan

menús para audio e idiomas de subtítulos.

Aunque los contenidos de los menús DVD

y la operación cambian de disco a disco, a

continuación se explica la operación básica

cuando se utiliza esta característica.

Presione MENU durante la

reproducción. El menú de DVD

introducido en el disco se visualiza

ahora.

2

1) Presione

▲▼◄ ► o

las teclas

numéricas para

seleccionar

el articulo

deseado.

2) Presione SET o

PLAY.

Utilización de un menu de DVD

[DVD solamente]

ANGULO

: 1

ELEGIR :

ANGULO

: 2

SONIDO: 2 ENG VOZ ACTIVO

ELEGIR

:

TERMINAR : AUDIO

T

I

TLE MENU

Cas

t

l

es

Love

r

s

B

i

r

ds

Dogs

of the world

DVD MENU

3 . ANGLE

1 . SUBT

I

TLE

2 . AUD

I

O

• DVD Karaoke (1 vocal)

VOCAL ON➞VOCAL OFF

• DVD Karaoke (2 vocales)

VOCAL V1➞VOCAL V2➞VOCAL V1+V2➞VOCAL OFF

• Video CD

LR➞L➞R

5757

For Your Information

Puede usted programar pistas especíﬁ cas y el orden de

reproducción.

Presione ACTION en el modo paro (STOP)

para visualizar MAIN MENU.

1) Presione ▲▼

para seleccionar

“MODO DE

REPRODUCCION.”

2) Presione SET para

visualizar.

1) Presione ▲▼

para seleccionar

“REPRODUCCION

DE PROGRAMAS.”

2) Presione SET para

visualizar.

1) Presione

▲▼◄ ► para

seleccionar “DVD.”

2) Presione SET para

visualizar.

1) Presione ▲▼◄ ►

para seleccionar el

número de la pista

deseada. (Se

visualizan los

números de la pista

del disco).

2) Presione SET para

seleccionar.

• Repita el paso 5 para

seleccionar otra pista.

• La pista seleccionada se

añade a la parte derecha.

1) Presione ▲▼◄ ►

para seleccionar

“INICIAR.”

2) Presione SET.

• La reproducción

comienza en la secuencia

programada.

• Para cancelar, presione

STOP durante la

reproducción y luego

presione CLEAR.

1

3

4

2

5

6

Las pistas se reproducen de forma arbitraria.

Repita los pasos 1-3 de la

“Reproduccion programa”.

1) Presione

▲▼ para

seleccionar

“REPRODUCCION

ALEATORIA.”

2) Presione SET.

• Comienza la

reproducción

arbitraria.

• Para cancelar,

presione STOP

durante la

reproducción y

luego presione

CLEAR.

1

2

Reproducción programada

[Vídeo CD/CD]

Reproducción arbitraria

[Vídeo CD/CD]

MENU PR

I

NCIPAL

DVD

BLOQUEO

CANAL

RELOJTV

ID

I

OMA

TERM

I

NAR :

ACT

I

O

N

ELEG

I

R

:

F

I

JAR

:

SET

5

3

1

DVD MENU PRINCIPAL

ELEGIR :

FIJAR : SET

TERMINAR : ACTION

IDIOMAS DEL DI SCO

SALIDA DE AUDIO

DETENER RASTREO : CAMPO

4:3 PREFERENCIA : Letterbox

MODO DE REPRODUCCION

ELEGIR :

FIJAR : SET

TERMINAR : ACTION

REPRODUCCION DE PROGRAMAS

REPRODUCCION ALEATORIA

REPRODUCCION DE PROGRAMAS

ELEGIR :

FIJAR : SET

TERMINAR : ACTION

DISCO

PROGRAMA

1 61116 5 8

2 7 12 17 15 6

3 8 13 18 1 13

4 91419 3 2

5101520 2

BORRAR EL ULTIMO

BORRAR TODO INICIAR

REPRODUCCION DE PROGRAMAS

ELEGIR :

FIJAR : SET

TERMINAR : ACTION

DISCO

PROGRAMA

1 61116 5 8

2 7 12 17 15 6

3 8 13 18 1 13

4 91419 3 2

5101520 2

BORRAR EL ULTIMO

BORRAR TODO INICIAR

MODO DE REPRODUCCION

ELEGIR :

FIJAR : SET

TERMINAR : ACTION

REPRODUCCION DE PROGRAMAS

REPRODUCCION ALEATORIA

58

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

58

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Spanish Quick Use Guide/Guía para rápida consulta

1) Presione st para seleccionar el artículo

deseado.

2) Presione SET.

4

1

2

3

5

Volver a visualizar el menú de

DVD para continuar el ajuste.

Presione ACTION y pase al paso 3 para ajustar

otro

articulo o, para salir, presione ACTION

tres veces.

Presione ACTION en el modo de paro

(STOP) para visualizar MAIN MENU.

1) Presione ▲▼◄ ► para seleccionar

“DVD.”

2) Presione SET para visualizar.

1) Presione st para seleccionar el artículo

deseado.

2) Presione SET.

IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco pueden ser

ajustados, Si el idioma ajustado no es ofrecido en el

disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio procedente de la

terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO” o “CUADRO” para

prevenir inestabilidad o para permitir ver textos

pequeños o patrones ﬁ nos claramente en el modo de

imagen ﬁ ja.

4 : 3 PREFERENCIA

Para seleccionar si el material del vídeo para pantalla

ancha será vuelto a reproducir en el estilo Pan&Scan

o en el estilo Letterbox en la pantalla.

Seleccione “AUDIO”

Inglés/Español/Francés/Japones: (Fijación de fábrica : inglés)

Original : Se seleccionará el idioma original de cada

disco.

OTRO **** : Se puede seleccionar el otro idioma.

Seleccione “SUBTITULO”

AUTO : Se seleccionará el mismo que fue seleccionado

en la preparación de “AUDIO”. (Fijación de fábrica)

• Si el idioma seleccionado en la preparación de

“AUDIO” se utiliza durante la reproducción, los

subtítulos no aparecerán.

• Si se utiliza otro idioma durante la reproducción,

los subtítulos aparecerán en el idioma

seleccionado en la preparación de “AUDIO”

Inglés/Español/Francés/Japones

OTRO **** : Se puede seleccionar el otro idioma.

Seleccione “MENU”

Inglés/Español/Francés/Japones : (Fijación de fábrica : inglés)

OTRO **** : Se puede seleccionar el otro idioma.

Selección de IDIOMAS DEL DISCO

[DVD solamente]

2

3

1) Presione ▲▼ (o ◄► ) para

seleccionar el articulo deseado.

2) Presione SET para colocar.

1

Cuando se presiona DISPLAY, la visualización

en pantalla muestra la información del disco

(título / capítulo / número de lista, tiempo

transcurrido de reproducción, audio / idioma

del subtítulo, y ángulo) e información (repetir

la reproducción, modo reproducción, Karaoke

vocal encendido / apagado, etc.).

Presione DISPLAY en el modo

reproducción o parada para visualizar

en pantalla.

• Cada vez que se presione DISPLAY, la

visualización en pantalla cambia como se

muestra a continuación.

Para volver

a la pantalla

normal,

presione

repetidamente

CLEAR o

DISPLAY.

Funcionamiento del DVD utilizando

visualizaciones en pantalla

1)Presione

▲▼

para

seleccionar

el ajuste

deseado.

2)Presione

SET para

colocar.

Fijaciones iniciales

ELEGIR :

FIJAR : SET SIGUIENTE: DISPLAY

T I TULO : 12 DVD

CAPITULO

: 11 0:12:34

PISTA : 12 VIDEO CD

PBC : INACTI VO 0 : 12 : 34

FIJAR : SET SIGUIENTE: DISPLAY

PISTA : 17 VIDEO CD

PBC : INACTI VO 0 : 12 : 34

FIJAR : SET SIGUIENTE: DISPLAY

ELEGIR :

FIJAR : SET SIGUIENTE: DISPLAY

T I TULO : 12 DVD

CAPITULO:

24 0:12:34

Información seleccionada del disco

Pantalla normal

Información seleccionada de la unidad

5959

For Your Information

Selección de DETENER RASTREO

AUTO : Durante el modo de imagen ﬁ ja se

seleccionarán automáticamente

“Campo ﬁ jo” o “Cuadro ﬁ jo” (Fijacion

de fabrica)

CAMPO : Seleccione este ajuste cuando ocurra

“distorsión” en las imagenes, incluso

cuando se haya seleccionado “AUTO”.

CUADRO : “Cuadro ﬁ jo” esta siempre

seleccionado. Se utiliza cuando no

se puedan ver claramente textos

pequeño o patrones ﬁ nos incluso

cuando esté seleccionado “AUTO”.

Selección de 4 : 3 PREFERENCIA

4:3 Pan&Scan : Datos de la pantalla ancha

de vídeo son reproducidos

en el estilo Pan & Scan (la

parte derecha e izquierda de

la pantalla son recortadas).

(Fijación de fábrica)

• Datos de vídeo no

formateados en Pan & Scan

serán reproducidos en el estilo

letterbox.

4:3 Letterbox : Datos de la pantalla ancha de

vídeo son reproducidos en el

estilo Letterbox (la parte de

arriba y abajo de la pantalla

tienen un margen negro).

Funcionamiento de la ejecución de MP3/WMA/JPEG

Puede utilizar esta unidad para reproducir audio

de formato MP3/WMA/JPEG, grabado para uso

personal con una computadora, etc., en un

CD-ROM o CD-RW.

La ejecución puede no tener lugar en algunos

casos, debido a las condiciones de la grabación.

Presione POWER en el control remoto o

unidad.

Presione OPEN/CLOSE y a continuacion

coloque un disco MP3/WMA/JPEG en la

bandeja de discos.

Presione OPEN/CLOSE para cerrarla.

Se visualizará el MENU MP3/WMA/JPEG

y la ejecución se iniciará

automáticamente.

(Se visualizará el directorio del CD.)

Estado de

la función

Área de las

carpetas

(La carpeta

visualizada

actualmente

se volverá

verde)

Contador

Carpeta

principal

Área de

archivos

(El

archivo/ la

carpeta se

visualiza

con un

cursor.)

MODO DE REPRODUCCIÓN

1

2

3

REPROD

MODE DE REPRODUCCION:

NORMAL

00

:

00

:

00

ROOT

. .

My favorite

CAR1

TECHNO

CAR2

POPS

END

_

W

ALTZ

J

AZZ

PICTURES

:

Archivo MP3

:

Archivo WMA

:

Archivo JPEG

:

Carpeta

:

Carpeta principal

■

Ejecución MP3/WMA/JPEG (Durante el modo STOP)

Presione para seleccionar un archivo

MP3/WMA

( / ) o un archivo JPEG

(

)

, y

presione SET o PLAY.

• MP3/WMA

Búsqueda hacia adelante/hacia atrás

➞Presione

SEARCH/SLOW

o

SEARCH/SLOW

durante la ejecución.

Salto de Pista hacia adelante/hacia atrás

➞Presione SKIP+

|

o SKIP-

|

durante la

ejecución.

• JPEG

Búsqueda siguiente/anterior

➞Presione SKIP+

|

o SKIP-

|

.

Inicie la muestra-diapositiva

➞

Presione

SEARCH/SLOW

o

SEARCH/SLOW

.

Ampliando una imagen ➞Presione ZOOM.

Rotando una imagen

➞Presione ANGLE.

Presione STOP para detener la operacion descrita

arriba.

■Seleccione MODO DE REPRODUCCION

(Durante el modo STOP)

Presione

para mover el cursor a MODO DE

REPRODUCCION, y Presione

para

seleccionar el

MODO DE REPRODUCCIÓN deseado.

[MODO DE REPRODUCCIÓN]

NORMAL: Todos los archivos se reproducen sólo

una vez

REPETICION DE UNA MUSIC:

El archivo seleccionado se reproduce

repetidamente.

REPETICION DE UN ARCHIVO:

Los archivos que se encuentran en la carpeta

seleccionada se reproducen repetidamente.

REPETICION DEL DISCO:

Todos los archivos se reproducen repetidamente.

4

Presione ACTION para regresar al DVD

MAIN PRINCIPAL.

60

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

60

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

PANASONIC CONSUMER ELECTRONICS

COMPANY, DIVISION OF MATSUSHITA ELECTRIC

CORPORATION OF AMERICA

One Panasonic Way Secaucus, New Jersey 07094

PANASONIC SALES COMPANY, DIVISION OF

MATSUSHITA ELECTRIC OF PUERTO RICO, INC.,

AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial

Park, Carolina, Puerto Rico 00985

Panasonic/Quasar Video Products

Limited Warranty

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or workmanship, Panasonic

Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)

will, for the length of the period indicated on the chart below, which starts with the date of original

purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, or

(b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the

warrantor.

During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period,

there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home

service, as applicable, during the warranty period.

If non-rechargeable batteries are included, they are not warranted. This warranty only ap plies to

products purchased and serviced in the United States or Puer to Rico. This warranty is extended only to

the original purchaser of a new product which was not sold “as is.” A purchase receipt or other proof of

the original purchase date is required for warranty service.

Carry-In, Mail-in or In-Home Service

For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact

number listed above or visit Panasonic Web Site: http://www.panasonic.com

For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.

In-Home service, if applicable, requires clear, complete and easy access to the product by the

authorized servicer and does not include removal or re-installation of an installed product. It is possible

that certain in-home repairs will not be completed in-home, but will require that the product, or parts of

the product, be removed for shop diagnosis and/or repair and then re turned.

Limited Warranty

Product

Parts Labor Service Contact Number

Camcorder

One (1) Year (except CCD

Image Sensor)

CCD Image Sensor - 6 (Six)

Months

Ninety (90) Days

Carry-In or Mail-In 1-800-211-PANA(7262)

DVD/VCR Deck,

A/V Mixer

One (1) Year Ninety (90) Days Carry-In or Mail-In 1-800-211-PANA(7262)

TV/VCR, TV/DVD,

TV/DVD/VCR

Combination

One (1) Year (except CRT)

CRT - Two (2) Years

Ninety (90) Days

Carry-In: 21″ CRT and Smaller

In-Home or Carry-In: 22″ CRT and

Larger

1-800-211-PANA(7262)

TV/HDR

Combination

One (1) Year (except CRT)

CRT - Two (2) Years

Ninety (90) Days

In-Home or Carry-In 1-888-843-9788

Rechargeable

Batteries

(in exchange for

defective item)

Ten (10) Days Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262)

Tape

(in exchange for

defective item)

Five (5) Days Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262)

Memory Cards

(in exchange for

defective item)

Ninety (90) Days Not Applicable Carry-In or Mail-In 1-800-211-PANA(7262)

6161

For Your Information

Customer Services Directory

Web Site: http://www.panasonic.com

You can purchase parts, accessories or locate your

nearest servicenter by vis it ing our Web Site.

For Product Information, Operating Assistance, Literature Request, Dealer

Lo ca tions, and all Customer Service inquiries please contact:

1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm,

EST. or send e-mail : [email protected]

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/

Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,

Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

1-800-332-5368 (Customer Orders Only)

For hearing or speech impaired TTY users, TTY : 1-866-605-1277

Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032

(Monday-Friday 6 am-5 pm; Saturday 6 am-10:30 am, PST)

(Visa, MasterCard, Discover Card, American Express, Check)

Accessory Purchases:

Limited Warranty Limits And Exclusions

This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT

COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on

the picture tube resulting from viewing ﬁ xed images (including, among other things, letterbox pictures

on standard 4:3 screen TV’s, or non-expanded standard 4:3 pic tures on wide screen TV’s, or onscreen

data in a stationary and ﬁ xed location). The warranty ALSO DOES NOT COVER damages which

occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures

which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty

installation, set-up ad just ments, misadjustment of consumer controls, improper maintenance, power

line surge, lightning damage, modiﬁ cation, or commercial use (such as in a hotel, ofﬁ ce, restaurant, or

other business), rental use of the product, service by anyone other than a Factory Servicenter or other

Authorized Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY

COVERAGE.” THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH

OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone

remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of media or

images, data or other memory or recorded content. The items listed are not exclusive, but are for

illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF

MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or

limitations on how long an implied warranty lasts, so the exclusions may not apply to you.

This warranty gives you speciﬁ c legal rights and you may also have other rights which vary from state

to state. If a problem with this product develops during or after the warranty period, you may contact

your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the warrantor’

s Consumer Affairs Department at the addresses listed for the warrantor.

PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE

APPLICABLE) WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR

RESPONSIBILITY.

As of August 2002

62

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

62

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

TV

Index

A Accessories......................................... 4

AC Power Plug.................................... 9

ACTION button.............................. 8, 12

ADD/DLT/CLEAR button ............... 8, 13

Audio Adjustment.............................. 33

Audio Auto Gain Control (AGC) ........ 32

AUDIO button.......................... 8, 19, 25

Audio Connections....................... 14-15

Audio Features............................. 32-33

Audio Menu....................................... 32

Audio Mode for FM Radio ................. 25

Audio Mode for TV Viewing ............... 19

Audio Mute........................................ 18

Audio/Video Input connector (LINE).... 9

Audio Output Connector (L/R)............. 9

Auto Operation Functions ................. 26

B Batteries.............................................. 4

Before Requesting Service .......... 50-51

Before Using ....................................... 4

Blocking Message............................. 31

Blue Screen Display.......................... 23

Broadcast Types................................ 19

C Caption On Mute .............................. 21

Channel............................ 10, 12-13, 23

CHANNEL UP/DOWN button........ 8, 18

Clock ................................................. 12

Closed Caption ............................ 20-21

Connections ...................................... 10

Connections, Audio ...................... 14-15

Connections, ANT./Cable .................. 10

Customer Services Directory .......... 61

D DISPLAY button ............................ 8, 23

DST (Daylight Saving Time).............. 11

F FM button................................. 8, 24-25

FM Radio ..................................... 24-25

Front Panel Indicators ......................... 9

I

Important Safeguards and Precautions

.. 2

Information (Unit, Disc) .................... 6-7

Initial Setup ....................................... 10

Indicators on the Front Panel .............. 9

Input Mode ........................................ 26

L Language .......................................... 12

Limited Warranty .......................... 60-61

Location of Controls ............................ 8

M MTS Broadcast/TV Stereo System ... 19

MUTE button................................. 8, 18

N NUMBER keys .............................. 8, 18

O 100 Key ............................................. 18

On-Screen Display (OSD)................. 23

ON-TIMER Indicator...................... 9, 22

ON-TIMER with Alarm ...................... 22

P Phones.............................................. 18

POWER button.............................. 8, 10

Q Quality Picture..................................... 4

R Rapid Tune ........................................ 18

R-TUNE button.............................. 8, 18

Remote Control Buttons...................... 8

Remote Sensor ................................... 9

Reset Language, Channels, Clock.... 12

Reset unit.......................................... 11

S Safety Precautions .............................. 3

Secret Code ...................................... 28

SELECT/SET button ..................... 8, 12

Sleep Timer....................................... 22

SLEEP TIMER Indicator................ 9, 22

Spanish Quick Use Guide .......... 53-59

Speciﬁ cations...................................... 6

SURROUND button ...................... 8, 27

Surround Sound................................ 27

T Table of Contents ................................ 5

Time Zone Adjust .............................. 13

TV Timer Features............................. 22

U Unit, Front/Rear View .......................... 9

US MOVIES Ratings ......................... 29

US TV PROGRAMS Ratings............. 30

V Video Adjustment.............................. 33

Video/Audio Menu ............................. 32

Video/Audio Adjust ............................ 33

Video Menu ....................................... 32

V-Chip Control Feature................. 28-31

VHF/UHF Antenna Input Terminal....... 9

VOLUME UP/DOWN button .......... 8, 18

W Warning and Instruction Displays...... 52

6363

For Your Information

DVD

A ANGLE button......................... 8, 35, 44

ANGLE Indicator ........................... 9, 35

Auto-Power Off function .................... 17

AUDIO button.......................... 8, 34, 35

AUDIO OUTPUT ............................... 47

Audio soundtrack language (DVD) .... 34

B Basic DVD Operation ........................ 16

C CLEAR button .......................... 8, 37-39

D Deﬁ nition of terms............................... 7

Disc Audio attribute 1 type, sampling

frequency, bit No................................ 34

Disc format.......................................... 6

Disc handling ...................................... 7

Disc information screen..................... 40

DISC LANGUAGES (DVD)................ 46

Disc Operation ............................. 34-38

Disc Tray.................................... 7, 9, 16

DISPLAY ...................................... 39-41

DISPLAY button ............................ 8, 39

DVD button.................................... 8, 16

DVD Lock Feature (DVD) .................. 45

DVD Lock Ratings (DVD) .................. 45

DVD menu (DVD) .............................. 36

DVD Operation using On-Screen ... 39-41

DVD Volume Adjust........................... 27

F Forward/Reverse Chapter/Track skip... 17

Forward/Reverse rapid scene search ... 17

Frame by Frame picture

(DVD/Video CD)................................ 17

J JPEG Playback ............................ 43-44

K Karaoke (DVD/Video CD).................. 35

L Language Code List.......................... 49

M MENU button ................................ 8, 36

MP3 Playback ................................... 43

Multiple angle viewing (DVD) ............ 35

O OPEN/CLOSE button.................... 8, 16

Optical digital audio output

connector ................................. 9, 14-15

P PAUSE button ............................... 8, 17

Picture Zoom (DVD).......................... 35

Play ................................................... 16

Playback control (Video CDs) ........... 17

PLAY button .................................. 8, 16

Program Play (Video CD/CD) ........... 37

Program Repeat Play (Video CD/CD) .. 37

R Random Play (Video CD/CD)............ 38

Region number.................................... 3

Repeat Play ...................................... 41

RESUME function ............................. 17

RETURN button ............................ 8, 16

S SEARCH/SLOW

/ ...8, 16-17, 43-44

Settings for DVD Operation.......... 46-48

SKIP+

|

/SKIP-

|

... 8, 16-17, 42-44

Slow Motion (DVD/Video CD) ........... 17

STILL MODE..................................... 48

Still (Pause) Picture........................... 17

Subtitle language (DVD) ................... 34

SURROUND/VSS button .............. 8, 27

T TV MODE.......................................... 48

Title menu (DVD)............................... 36

U Unit information screen (Unit) ........... 41

V V.S.S. (Virtual Surround Sound)........ 27

W WMA Playback.................................. 43

Z ZOOM button ................................ 8, 35

LSQT0669B

Panasonic Consumer Electronics Company,

Division of Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”),

Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería, Km. 9.5

San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Printed in Indonesia

LSQT0669B

S0303-1033

P

Panasonic PV 20D53 Manual de usuario

Este manual también es adecuado para

Panasonic PV 20D53 Manual de usuario

en otros idiomas

Artículos relacionados

Otros documentos