Panasonic MP3 Player PV-D4762 Manual de usuario

Marca: Panasonic

Modelo: MP3 Player PV-D4762

Categoría: Reproductores de DVD

Tipo: Manual de usuario

Este manual también es adecuado para

PV-D4762

PV-D4762

DVD/VCR DECK

Operating Instructions

Model No.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Initial Setup

(Connection)

Basic

Operation

VCR

Operation

For Your

Information

DVD

Operation

Connections and Initial Setup Procedures are on pages 12 to 17.

Please read these instructions carefully before attempting to connect, operate or

adjust this product. Please save this manual.

Spanish Quick Use Guide is included.

(Guía para rápida consulta en español está incluida.)

LSQT0525A

As an ENERGY STAR Partner, Matsushita Electric Corporation of

America has determined that this product or product model meets the

ENERGY STAR guidelines for energy efficiency.

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the

unit or in this manual. If necessary, have your

Electric Utility Service Company or Video Products

Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either

a polarized power cord plug (one blade is wider

than the other), or a three-wire grounding type plug.

POLARIZED PLUG CAUTION:

This plug will only fit into an outlet one way. If you cannot

fully insert the plug, try reversing it. If it still will not fit,

have an electrician install the proper wall outlet. Do not

defeat the safety feature by tampering with the plug.

GROUNDING PLUG CAUTION:

This plug will only fit into a three-hole grounding

outlet. If necessary, have an electrician install the

proper outlet. Do not defeat the safety feature by

tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they

are not likely to have anything rest on them, roll

over them, or be in the way of walking traffic.

If an extension cord is used, make sure it also

has either a polarized or grounded plug and that

the cords can be securely connected.

Frayed cords, damaged plugs, and damaged or

cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire

hazards and should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat

generated during operation. If they are blocked,

heat build-up inside the unit can cause failures that

may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in

use, or operate the unit when placed on a bed,

sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS

OR SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or

radiator, in direct sunlight, inside closed vehicles,

in high temperature [over 104°F (40°C)], or in over

75% humidity. If the unit is suddenly moved from

a cold place to a warm one, moisture may

condense in the unit and on the tape causing

damage. Never subject the unit to vibration,

impact, or place it so that the surface is titled as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping

surface.

• Do not place this unit on any support that is not

firm, level, and adequately strong.

The unit could fall causing serious

injury to a child or adult and

damage to the unit.

• An appliance and cart

combination should be moved

with care. Quick stops,

excessive force, and uneven

surfaces may cause the appliance and cart

combination to overturn.

• Carefully follow all operating instructions and

use the manufacturer's recommended

accessories when operating this unit or

connecting it to any other equipment.

FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY

AND OPERATING INSTRUCTIONS. HEED ALL

WARNINGS IN THE MANUAL AND ON THE UNIT

USING THE UNIT

If the unit has been in storage or moved to a new location,

refer first to the INSTALLATION section of these safeguards.

KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT, unplug the unit and have it inspected by a

qualified service technician before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or

before leaving the unit unused for extended periods of time,

disconnect all equipment from the power source as well as

the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE

if liquid has been spilled into the unit. Immediately unplug

the unit, and have it inspected by a service technician.

Fire and shock hazards can result from electrical shorts

caused by liquid contact inside.

• Never drop or push any object through openings in the unit.

Some internal parts carry hazardous voltages and contact

can cause electric shock or fire hazard.

Do not put any foreign object on the disc tray.

• Avoid placing the unit directly above or below your TV set

as this may cause electrical interference. Keep all magnets

away from electronic equipment.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to

avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated

cloth to gently remove dust or debris. DO NOT USE cleaning

fluids, aerosols, or forced air that could over-spray, or seep

into the unit and cause electrical shock. Any substance such

as wax, adhesive tape, etc. may mar the cabinet surface.

Exposure to greasy, humid, or dusty areas may adversely

affect internal parts.

SERVICE

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating

instructions, this product does not operate properly, do not

attempt to open or remove covers, or make any

adjustments not described in the manual. Unplug the unit

and contact a qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified

by the manufacturer, or those having the same safety

characteristics as the original parts. The use of unauthorized

substitutes may result in fire, electric shock, or other hazards.

HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service

technician to conduct a thorough safety check as

described in the manufacture’s service literature to ensure

that the unit is in safe operating condition.

Important Safeguards and Precautions

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC

- NATIONAL

ELECTRICAL CODE

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the

equipment, be sure the antenna or cable system is grounded

so as to provide some protection against built up static

charges and voltage surges.

Section 810 of the National Electrical

Code, ANSI/NFPA 70 (in Canada,

part 1 of the Canadian Electrical

Code) provides information

with respect to proper grounding

of the mast and supporting

structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes and requirements for the grounding electrode.

KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

An outside antenna system should be located well away from

power lines, electric light or power circuits and where it will never

come into contact with these power sources if it should happen

to fall. When installing an outside antenna, extreme care should

be taken to avoid touching power lines, circuits or other power

sources as this could be fatal. Because of the hazards involved,

antenna installation should be left to a professional.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol warns the user that uninsulated voltage

within the unit may have sufficient magnitude to cause

electric shock.

Therefore, it is dangerous to make any kind of contact

with any inside part of this unit.

This symbol alerts the user that important literature

concerning the operation and maintenance of this unit

has been included. Therefore, it should be read

carefully in order to avoid any problems.

FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

Safety Precautions/Mesures de sécurité

WARNING: To prevent fire or shock hazard, do not expose this

equipment to rain or moisture.

CAUTION: To prevent electric shock, match wide blade of plug to

wide slot, fully insert.

Avertissement: Afin de prévenir tout risque d’incendie ou de chocs

électriques, ne pas exposer cet appareil à la pluie ou

à une humidité excessive.

Attention: Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la

prise et pousser jusqu’au fond.

Region Management Information:

This DECK is designed and manufactured to respond to the

Region Management Information that is recorded on a DVD

disc. If the Region number described on the DVD disc does

not correspond to the Region number of this DECK, this

DECK cannot play this disc.

The Region number

for this DECK is 1.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.

HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD

CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.

BE SURE TO OPERATE THE UNIT CORRECTLY INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE

YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER

OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE UNIT

YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION

WHEN OPEN DO NOT

STARE INTO BEAM.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited

viewing uses only.

ATTENTION:

RAYONNEMENT

LASER EN CAS

D’OUVERTURE.

NE PAS REGARDER

DANS LE FAISCEAU.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when operated in a residential

environment. If this equipment does cause interference to radio or television reception, which can be

determined by turning the equipment off and on, use the equipment in another location and/or utilize

an electrical outlet different from that used by the receiver.

If necessary, consult the dealer or an experienced ratio/TV technician for help. The user may find the

booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to

other devices.) Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Congratulations

on your purchase of one of the most

sophisticated and reliable products on the

market today. Used properly, it will bring you

years of enjoyment. Please fill in the

information below. The serial number is on the

tag located on the back of your DECK.

Before Using

Accessories

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No. PV-D4762

• Serial No.

To order accessories, call toll free

1-800-332-5368.

If disc is brought from a cold to a warm

environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth

before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Disc Handling

To clean disc surface

With a soft, damp (water only) cloth, gently wipe

from the center hole to the outer edge as shown

below. (Wiping in a circular pattern will scratch the

surface.)

Handling precautions

• Only hold disc by edges as shown below.

Fingerprints, dirt and scratches can cause

skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning sprays, benzine,

thinner, static electricity prevention liquids, or any

other solvent.

• Be careful not to drop or bend disc.

• Do not place more than

1 disc on disc tray.

• Do not try to close

disc tray when disc

is not properly placed.

• Always store discs in

their proper cases

when not in use.

Disc formats supported by this DECK

DECK can play back discs bearing any of the

following marks:

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• DVD of PAL system • DVD-R/DVD-RAM

• DVD-ROM • CD-ROM

• CDV • CD-G

DVD

3” (8 cm) disc / 5” (12 cm) disc

Video CD

3” (8 cm) disc / 5” (12 cm) disc

is a registered trademark.

Do not try to play Photo CD.

Disc tray

Disc

RF Coaxial Cable

VJAS0196

Batteries 2 “AA”

Remote Control

LSSQ0334

1) Open cover.

3) Close cover.

Loading the Batteries

2) Insert

batteries as

marked.

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese

batteries.

Table of Contents

Timer Recording..............................................................24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System ....................26, 27

Multi-Brand Control Feature ...........................................28, 29

Tape Operation ( and ) ...30 ~ 36

Special VCR Features .....................................................37, 38

Copying Your Tapes (Dubbing) .........................................................39

Disc Operation ...............................................................40 ~ 44

DVD Operation using On-Screen Displays .................45 ~ 46

MP3 Playback Operation.......................................................47

DVD Lock Feature .................................................................48

Settings for DVD Operation ..........................................49 ~ 51

Language Code List..............................................................52

DVD / VCR

Warning and Instruction Displays........................................53

Before Requesting Service.............................................54, 55

Servicenter List......................................................................56

Limited Warranty ...................................................................57

Spanish (Español) Quick Use Guide.............................58 ~63

Index.......................................................................Back Cover

DVD / VCR

Important Safeguards and Precautions ............................2, 3

Before Using............................................................................4

DECK & Cassette Information........................................... 6 , 7

Location of Controls .......................................................8 ~ 10

Displays (On Screen Displays and Multi Function Display) ....................11

Connections ..................................................................12 ~ 15

Initial Setup for Basic Connections (Ready to Play) ..........16, 17

VCR

Reset Language, Channels, Clock, VCR’s Output Channel ...18, 19

Playback/ Record on a Tape...........................................20, 21

DVD

Basic DVD Operation ......................................................22, 23

Initial Setup

(Connection)

Basic

Operation

VCR

Operation

For Your

Information

DVD

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

DECK & Cassette Information

Video Head Clog Sensor

During playback, this

screen appears if

clogging is detected.

To remove screen,

press PLAY on the

remote or DECK.

Playing older or damaged tapes may eventually

cause video heads to become clogged.

EO HEADS

EED

CLE

PLEASE

NSERT

HEAD

CLE

CASSE

REFER

MANUAL

END

• Use “dry” type head cleaning cassette

only. (Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.

Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your

nearest Factory Servicenter or authorized

Servicenter (see p. 56).

Head Cleaning

Only use tapes with the mark in this DECK.

Prevent Accidental Tape Erasure

Record/ Playback Time

Record Tab

Cover the hole

with cellophane tape.

To record again

Break off the tab to

prevent recording.

(Standard Play)

2 Hours

40 Minutes

1 Hour 2 Hours

5 Hours

20 Minutes

2 Hours 4 Hours

(Long Play)

3 Hours 6 Hours 8 Hours

SLP

(Super Long Play)

Type of Video Cassette

Tape Speed

Setting

T160T120T60

Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes

on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be

marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since

the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive,

antistatic cleaner and polisher.

Cleaning DECK

Digital Auto Picture

Automatically controls the video output signal for less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for optimum picture quality.

Manual Tracking Control

(to reduce picture noise)

Use during Playback and Slow Motion mode to reduce picture noise.

Press CH (TRACKING) / on the remote control or on DECK until the picture clears up.

To return to Auto Tracking, press POWER off, then on again a few seconds later.

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a V-Lock control.

Features for a Quality Picture (VCR)

Built-in Head Cleaner

A clean video head helps produce a clear

picture.

So, we have equipped your DECK with

a built-in, non-chemical head cleaning system

that helps prevent clogging of the video

heads. Cleaning is performed each time you

load or unload a video cassette.

• This feature is preventative only, If your video

heads are seriously clogged, consider the use

of a chemical non-abrasive head cleaning kit

or take your DECK to a Servicenter.

Screw driver

Power Source: 120 V AC, 60 Hz

Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts

Video Signal: EIA Standard NTSC color

Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)

Tuner:

Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69

CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)

Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output

Input Terminal: Audio/Video Line Input (Front)

Output Terminal: S-VHS Output (DVD only), Component Video Output (DVD only)

Audio Output 2 (L), (R)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)

Operating Humidity: 10 % ~ 75 %

Weight: 6.9 kg (15.2 lbs).

Dimensions: 430 (W) x 118 (H) x 364 (D) mm

16-15/16” (W) x 4-5/8” (H) x 14-5/16” (D) inch

Discs Played

(1) DVD-VIDEO Disc 5” (12 cm) single-sided single-layer

5” (12 cm) single-sided double-layer

5” (12 cm) double-sided double-layer (one layer per side)

3” (8 cm) single-sided single-layer

3” (8 cm) single-sided double-layer

3” (8 cm) double-sided double-layer (one layer per side)

(2) Compact Disc 5” (12 cm) disc

(CD-DA, VIDEO CD) 3” (8 cm) disc

Digital Audio Output: Digital Optical Connector

Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)

Laser power: CLASS II

Specifications

Note: • Designs and specifications are subject to change without notice.

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

The ANGLE button can be used to view the scene from different angles.

(ANGLE Indicator lights on DECK when a scene recorded at different

angles is detected.)

Chapter Number:Titles are subdivided into numbered sections. You can quickly search for

a favorite scene using these numbers.

DVD: A high-density optical disc on which high-quality pictures and sound have

been digitally recorded. DVD incorporates new video compression

technology (MPEG II) and high-density recording technology which allow

entire movies to be recorded with incredible playback quality.

Playback Control:With Video CD (version 2.0), scenes or information may be selected for

viewing or listening from an interactive menu that appears on the TV screen.

Subtitles: Written dialogue which appears at the bottom of the screen.

Time Number: The elapsed play time from the start of a disc or title. Use to quickly find

scenes. (May not work with some discs.)

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.

Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks

to be quickly located.

Video CD: CD containing picture and sound with same quality level as video tape.

This DECK also supports Video CDs with playback control (version 2.0).

Initial Setup

(Connection)

This product incorporates copyright protection technology that is protected by method claims of

certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and

other rights owners. Use of this copyright protection technology must be authorized by Macrovision

Corporation, and is intended for home and other limited viewing uses only unless otherwise

authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Location of Controls

Remote Control

ZOOM

p. 41

POWER

DSS/CABLE mode

p. 28

SPEED

p. 21

NUMBER keys

TV mode

p. 28

TAPE POSITION/

AUDIO CONTROL

p. 38,

EJECT/

OPEN/CLOSE

pp. 20,

ACTION

pp. 18

, 49

PAUSE

/STILL

pp. 20,

COUNTER

RESET

p. 35

PROGRAM

p. 24

RECORD

p. 21

ADD/DELETE/

CLEAR

pp. 19,

43, 48

VCR mode

p. 28

VOLUME

p. 28

CHANNEL /

TRACKING/V-LOCK

pp. 21, 6

PLAY

pp. 20,

REWIND/

SLOW-

pp. 20,

DVD mode

p. 28

INPUT

p. 39

DISPLAY

p. 11,

STOP

pp. 20,

FAST FORWARD/

SLOW+

pp. 20,

ANGLE

p. 41

SUB TITLE

p. 40

SURROUND/

ENTER

pp.

23,

p. 42

SET

VCR/TV

p. 21

RETURN

MOVIE ADVANCE/

pp. 22,

33, 34

TITLE

p. 42

AUDIO

(SAP/ Hi-Fi)

pp. 27,

SELECT

SKIP

p. 23

Bold: VCR Function

Italic

DVD Function

Bold Italic

VCR and DVD Functions

Normal: Others

Light button: When Light button is pressed, (DVD, TV, VCR, PLAY, STOP, REW, FF) buttons will light

up for 5 seconds for easy button location.

If no button is pressed in 5 seconds, the light goes out to conserve the battery.

EJECT button: When this button is pressed in VCR mode, the tape is ejected. This button is inoperative if

pressed during recording. If pressed in DVD mode, the disc tray opens or closes.

Light Tower Universal Remote Control

COMMERCIAL ADVANCE/

ZERO

pp. 30, 35

LIGHT

p. 8

Front View of DECK

Audio/Video

Input Connector 2

(LINE 2)

p. 39

CHANNEL /

TRACKING/V-LOCK

pp. 21, 6

POWER

PAUSE

p. 23

OPEN/CLOSE

p. 22

VCR/TV

p. 21

STOP/EJECT

p. 20

Multi Function

Display

p. 11

REC

p. 21

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid

wire (e.g. an extended paper clip) and,

applying moderate force, insert it straight

into the hole at the base of the tray.

The tray will eject a little. Now, pull the tray

all the way out and remove the disc.

Disc Tray

Over 2 inches

Cassette

Compartment

PLAY

p. 20

Remote

Sensor

FAST FORWARD/SEARCH

p. 20

REWIND/SEARCH

p. 20

Front View of DECK

Initial Setup

(Connection)

SKIP

p. 23

PLAY

p. 22

STOP

p. 22

Bold: VCR Function

Italic

DVD Function

Bold Italic

VCR and DVD Functions

Normal: Others

PROGRESSIVE

p. 10

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Location of Controls (continued)

Rear View of DECK

AC Power Plug

S-Video Out

Connector

(DVD Only)

pp. 10, 13

Component Video Output

Connector (Y, P

, P

) (DVD Only)

p. 13

Audio Output 2

Connector (L/R)

p. 13

Optical Digital Audio

Output Connector

(DVD Only)

p. 15

Video Input

Connector

p. 39

Video Output

Connector

p. 12

Audio Input

Connector (L/R)

p. 39

Audio Output 1

Connector (L/R)

p. 12

VHF/UHF Antenna Input Terminal

p. 12

VHF/UHF Antenna Output Terminal

p.12

DVD OUTPUT

DIGITAL

AUDIO OUT

(PCM/BITSTREAM)

OPTICAL

S-VIDEO OUT

SELECT

COMPONENT

VIDEO OUT

VIDEO

AUDIO1

OUT IN1

IN FROM ANT.

OUT TO TV

VHF/UHF

OUT

AUDIO2

SEE MANUAL

• While plugged into an AC outlet,

this DECK consumes 4 W of

electrical power in off mode.

••

The following table shows the status of the output jacks when in VCR or DVD mode.

Bold: VCR Function

Italic

DVD Function

Bold Italic

VCR and DVD Functions

Note

• PROG functions on the remote are not available when using Component Video Output

and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press

PROG.

SELECT SW (DVD Only)

p. 13

Video Output

Audio Out 1

Audio Out 2

Component

Video Output

S-VIDEO OUT

VCR

DVD

YES

YES YES

SELECT SW

(Switchable)➛YES

N/A N/A

To enjoy PROGRESSIVE SCAN video

➛

(1).Connect

Component Video Output

to the component video input terminals of a television.

(See p. 13.)

(2).Set the “COMPONENT VIDEO OUT”/“S-VIDEO OUT”

SELECT SWITCH

, in the back of the

DECK, to “COMPONENT VIDEO OUT.” (See above.)

(3).When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the

PROGRESSIVE SCAN signal is output from the

Component Video Output Connector

Note

• The PROGRESSIVE button can be operated when the DECK is in DVD function mode.

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• The unit does not output video signals from the “VIDEO OUT” or “S-VIDEO OUT” terminals

when the ON lamp is lit.

REC

SAP

ONO

VCR Status & Clock Displays

Blank Tape/ No Video Signal

Indications

Whenever a blank section of a tape

comes up in Play mode, or when the

selected channel has no broadcast

signal with Weak Signal Display

Feature (p. 37) set to OFF, the TV

screen will turn solid blue.

Function Status

Rec Time Remaining

(OTR mode only,

see p. 21.)

Current Time

Channel

Tape Speed

(See p. 6.)

Broadcast Audio

Being Received

(See p. 26.)

When a function button

is pressed, e.g. PLAY,

or you change

channels, a 5-second

display appears.

Counter

Displays (On Screen & Multi Function)

To display or remove

overlay at right,

➛➛

➛ press DISPLAY.

VCR

VCR REC

DVD

ANGLE

VCR

Hi-Fi

TIMER

•

Hi-Fi Indicator

Lights up when Hi-Fi audio

is monitored in Play mode.

VCR mode Indicator

Lights up when

DECK is VCR mode.

Power Indicator

Lights up when power is on.

Clock/ Status/ Channel/ Speed Display

Displays the current time. Briefly displays VCR

status when a function button is pressed. Briefly

displays the channel number, or “L1” or “L2” when

a channel or line input is selected. Briefly displays

the recording speed when SPEED is pressed.

ANGLE Indicator

Lights up when a scene

recorded at different

angles is detected.

See p. 41. (DVD only).

DVD mode Indicator

Lights up when

DECK is DVD mode.

VCR REC Indicator

Lights up during

recording.

Multi Function Display

On Screen Displays (VCR)

VCR Indicator

Lights up when the

VCR/TV selector is

set to VCR.

Timer Indicator

Lights up when DECK is set for

Timer Recording, or when One

Touch Recording (OTR) is

used. Flashes when Timer

Recording is set, but a tape has

not been inserted into DECK and

when a power interruption

occurs during Timer

Programming.

Lights up before noon.

PM is not displayed.

Function & Channel Displays

Initial Setup

(Connection)

CH 0

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Connections

1 Disconnect antenna or cable from TV

and connect to DECK.

WARNING

When using “Nut type” RF coaxial cables, tighten with

fingers only. Overtightening may damage terminals.

Basic Connections

• Connect DECK and TV with an RF Coaxial Cable

(supplied) or an AV Cable

(not supplied) as shown in the figure below.

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

FROM

ANT.

OUT

AUDIO

IN 1

OUT

DVD/VCR DECK

VHF/UHF

VIDEO

VHF/

UHF

VIDEO

AUDIO IN

AV CABLE

(not supplied)

2 Connect DECK to TV with RF Coaxial Cable.

RF COAXIAL CABLE

DSS

Receiver

OUT

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the

NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as practical.

OUT

Antenna or Cable

Cable Box

■ ■

■ DECK TV

■ ■

■ DSS Receiver DECK TV

■ ■

■ Cable Box DECK TV

You CannotYou Can

• record and view

both scrambled

and unscrambled

channels if

additional

equipment is

added.

This connection

requires: two

converter boxes,

an A/B switch,

and a 2-way

splitter.

• view channel

other than the

one selected

for any type of

recording.

• do a Timer

recording of a

channel unless

you select it on

the Cable Box.

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

IN 2IN 1

Cable Box

OUTIN

OUT 2

OUT 1

2-Way Splitter

OUT

A/B Switch

■■

■

Connect With Two Cable Boxes

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

Cable Box

OUTIN

OUT

VIDEO

AUDIO

ANT or CATV

You CannotYou Can

• record

scrambled

channels.

• view any

(including

scrambled)

channel.

• use Remote

Control to select

channels without

using Multi-brand

control feature.

ANT

CATV

VIDEO

AUDIO

OUT

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

or S-VIDEO mode).

If your TV has COMPONENT VIDEO INPUT, set SELECT SW to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, set SELECT

SW to S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

Connections For DVD Only

Other Connections

VIDEO

AUDIO

COMPONENT

VIDEO OUT

AUDIO OUT2

S-VIDEO OUT

SELECT

DVD OUTPUT

P R

S-VIDEO

From DECK’s

A/V OUTPUT

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,

and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only

from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT

Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

Notes

DVD/VCR DECK

VHF/

UHF

Cable Box

Note

• The picture will not be displayed if the SELECT SW is not set to the correct video output.

VHF/

UHF

Initial Setup

(Connection)

■ ■

■ With a Cable Box (DECK

Cable Box TV)

When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or

dts bitstream is output from the DECK OPTICAL digital audio output connector.

When DECK is connected to a Dolby Digital decoder or dts decoder, you can enjoy

theater-quality audio in your home. [An optical digital audio cable (optional) is

required when an optional Dolby Digital decoder or dts decoder is used.]

Notes on connecting an optical

digital audio cable (optional)

• Firmly connect the cable to the

connector.

Caution for optical digital audio output connector:

• When connecting an amplifier (with an optical digital input connector) which does not

contain the Dolby Digital or dts decoder, be sure to select “OFF” at “Dolby Digital” and

“OFF” at “dts” of the Settings for DVD Operation “AUDIO OUTPUT” (see p. 50).

Otherwise, any attempt to play DVDs may cause such a high level of noise that it may

be harmful to your ears and damage your speakers.

• When a dts decoder is connected, please select “Bitstream” at “dts” of the Settings for

DVD Operation “AUDIO OUTPUT”.

If “OFF” is selected, there will be no sound. (See p. 50).

• Video CDs and CDs can be played as usual.

Note:

• Some dts decoders which do not support DVD-dts interface may not work properly with DECK.

Amplifier

OPTICAL

DVD/VCR DECK

Front

Speaker

Front

Speaker

Surround

Speaker

Surround

Speaker

Center

Speaker

Subwoofer

Decoder with Dolby

Digital dts processing

(optional)

Optical Digital

Audio Cable

(optional)

To Optical

Digital Audio

Input Connector

Initial Setup

(Connection)

■ DECK Dolby Digital Decoder Amplifier Speaker

DECK dts (digital theater systems) Decoder Amplifier Speaker

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Before doing Initial Setup

Turn TV on.

See connections

RF Coaxial Cable Connection and

AV Cable Connection on p. 12.

Set TV to channel 3.

Set TV to VIDEO.

[DECK

➛➛

➛ TV]

• Go to “Doing Initial Setup (Ready to Play).” (See below.)

[Cable Box

➛➛

➛ DECK

➛➛

➛ TV], [DSS

➛➛

➛ DECK

➛➛

➛ TV]

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

in your time zone.

• If you use a DSS Receiver, it must be turned off.

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel

and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

channel 3, try switching it to channel 4.

• To change VCR’s output channel, please refer to “VCR’s Output Channel” on p. 19.

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

CH AUTO SET PROCEEDING

CANCEL : STOP

Plugging the AC Power Plug into

an AC outlet

Doing Initial Setup (Ready to Play)

Initial Setup for Basic Connections (Ready to Play)

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

ACTION

SET

SELECT

Settings are made automatically.

When setup is done, this screen appears.

If “AUTO CLOCK SET IS INCOMPLETE”

appears, manually set clock. See below.

SUN

20P

SETT

: CH

AUTO CLOCK SET

PLETED

If Auto Clock Set was incomplete.

Press ACTION* on remote to display

CLOCK screen.

Press

to select the month and SET to

set. In the same manner, select and set the

date, year, time, and DST (daylight saving

time).

Press ACTION to start clock and exit.

ET BACK :

ACT

2002

SUNSUN

SETSET

SET

Manual Clock Set

AUTO CLOCK SET IS

PLETE

PLEASE SET CLOCK BY

PRESSING

ACT

ON KEY

DST

THTH

/ /

SELE

SET

EXIT

ACT

SET

Initial Setup

(Connection)

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

Clock

2) Press to select

“MANUAL,” and press SET.

(For Auto Clock Set, select

“AUTO CLOCK SET.”)

3) Press and to

select, then set the date,

time, and DST (Daylight

Saving Time).

4) Press ACTION to start

Clock and exit this

mode.

(“TIME ZONE ADJUST”

appears only when auto

clock is set.)

SEL.

QUITTER

: ACTION

REGLER:SET

REGLAGE MAGNETOSCOPE

REGLAGE HORLOGE

REGLAGE CANAL

REGLAGE

COMMERCIAL

ADV.

LANGUAGE/IDIOMA:FRANÇAIS

CA SORTIE : 3

ELEGIR

SALIR

: ACTION

FIJAR : SET

PREPARAR VCR

FIJAR RELOJ

FIJAR CANAL

FIJAR PARA

ERC.

ADV.

LANGUE/LANGUAGE:ESPAÑOL

CANAL DE SALIDA : 3

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

Language

2) Press SET repeatedly.

For English

For Spanish

For French

1) Press

to select

language item.

Reset Language, Channels, Clock

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

Channels

2) Press to select

“ANTENNA,” then

press SET to set your

antenna system

(“TV” or “CABLE.”)

3) Press

to select

“AUTO SET,” then

press SET.

• If you use a Cable Box,

set it to the PBS channel

in your time zone.

• After Channel Auto Set

is finished, Auto Clock

Set will be performed.

Press ACTION*

to display MENU.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

3) Press ACTION to exit.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

SELE

SET

EXIT

ACT

ANT

ENNENN

CABLE

SPLA

OFF

ABLE

DSS

X SET UP

Plus

H SET UP

SET UP

NNE

AUT

K SET

JUS

SELE

SET

EXIT

ACT

SET

2002

SUN

SELECT

OUR

SET

SELE

SET

SET BACK :

EXIT

ACT

Press

to select

“SET UP CHANNEL,”

and

press SET

Press

to select

“SET CLOCK,” and

press SET

• PROGRAM functions are not available

when using COMPONENT Video Output

and S-VIDEO OUT. Please set TV to

either RF INPUT or VIDEO INPUT, and

then press PROGRAM.

CH AUTO SET PROCEEDING

CANCEL : STOP

Add or Delete a Channel

To add channel:

Select channel with NUMBER keys

and press ADD/DLT.

To delete channel:

Select channel with CH / or

NUMBER keys and press ADD/DLT.

HANNEL

ADDED

HANNEL

Time Zone Adjust

2) Press to select

“TIME ZONE ADJUST,”

VCR’s Output

Channel

1) Press to select

“VCR’S OUTPUT CH.,”

and press SET.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

2) Press SET.

3) Press ACTION.

After 3 seconds

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:4

• To Make Corrections,

repeat steps 1) ~ 3).

DST (Daylight Saving Time)

DECK auto adjusts clock for DST.

(p. 17.)

Spring (First Sunday in April)

DST:ON

➛➛

➛ Sets clock ahead one hour.

Autumn (Last Sunday in October)

DST:ON

➛➛

➛ Turns clock back one hour.

• If your area does not observe

Daylight Saving Time, select

DST:OFF.

• Keep these time changes in mind

when programming DECK for

timer recordings.

1) Press to select

“SET CLOCK,” and

press SET.

and press SET to

subtract or add hour(s)

as necessary.

*Important: If a remote control button does not work

when pressed, press the VCR button

on the remote and try the button again.

(Only when Auto Clock is set.)

3) Press ACTION twice.

• “TIME ZONE ADJUST”

returns to “0” if clock is

set manually.

YOU

PRESS

ACT

KEY, VCR’

UTPUT

TCHES

PLEASE

TUNE

SELE

SET

EXIT

ACT

SET

AUT

K SET

JUS

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

k VCR’s Output Channel

ADD/DLT

NUMBER

keys

POWER

ACTION

VCR

SET

SELECT

Basic

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Playback/ Record on a Tape

PAUSE/

STILL

REW/SLOW-

STOP

FF/SLOW+

EJECT

Insert a tape.

Playback using DECK buttons

Press PLAY.

CH /

SPEED

REC

VCR/TV

PLAY

Multi Function Display

Press STOP/EJECT to stop

and/ or eject a tape.

DVD

Insert a tape.

• DECK power comes on.

The VCR mode and “VCR” indicator light up

on Multi Function Display.

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

Press PLAY* to play a tape.

Playback a Tape

Ready Checklist

All connections are made (pp. 12 ~ 15).

TV and DECK are plugged in.

TV is on and tuned to CH3, 4, or VIDEO.

Remote is in VCR mode. (Press VCR.)

Press REW/SLOW- or FF/SLOW+ in Stop

mode to rewind or fast forward a tape.

Press EJECT on remote, or STOP/EJECT

on DECK to eject a tape.

Press STOP to stop a tape.

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛

➛ Press PLAY to release.

After search has begun, each additional press of

FF or REW changes speed as shown below.

[SLP] : Approx. 21X

↔ Approx. 9X

[LP] : Approx. 9X

↔ Approx. 7X

[SP] : Approx. 7X

↔ Approx. 3X

If at 21X, 9X, or 7X speed the picture is

interrupted, change speed to 9X, 7X, or 3X.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛

➛ Press PLAY to release.

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛

➛ Press PLAY to release.

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

REW/SLOW- (decrease speed) in Still

mode.

➛➛

➛ Press PLAY to release.

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary

depending on current tape position.

Notes

• These features work best in SP or SLP

mode.

• The sound will be muted.

• To reduce picture noise, see “Manual

Tracking Control” on p. 6.

• After DECK is in Still or Slow mode for 3

minutes, it will switch to Stop mode

automatically to protect the tape and the

video head.

Notes

Insert a tape with a record tab (p. 6).

• DECK power comes on.

The VCR mode and “VCR” indicator light up

on Multi Function Display.

Press CH , or NUMBER keys

to select the channel.

• For “LINE” input, see p. 39.

• If channel is over 100, press 100 key then press

the remaining 2 digits.

Press SPEED

to select the record speed (p. 6).

SP = Standard Play LP = Long Play

SLP = Super Long Play

Press REC

to start recording.

(The VCR REC indicator lights up on Multi Function

Display),

• To edit out unwanted scenes, press PAUSE/STILL

to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

• It is not possible to record from DVD/ Video

CD/ CD to VHS tape using DECK.

• Watching one channel and recording another

is not possible when using Cable Box or

DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to

protect a tape and video heads.

• Speed appears on-screen and on Multi Function Display.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Remove loose or peeling

labels from tapes to prevent

tape jam.

Multi Function Display

Record using DECK buttons

Select

Channel.

VCR/TV

Press REC

to start

Recording.

Press STOP/EJECT to stop.

This video recorder, equipped with HQ

(High Quality) system, is compatible

with existing VHS equipment. Only use

tapes with the mark. Only tapes

tested and inspected for use in 2, 4, 6,

and 8 hour machines are

recommended.

Normal Rec

0:30 1:00

1:302:003:004:00

Insert a tape.

Note

Notes

Basic

Operation

One Touch Recording (recording in progress),

➛➛

➛ Press REC repeatedly to set the recording length

➛➛

➛ (30 min. ~ 4 hours).

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV

(“VCR” goes out on Multi Function Display),

➛➛

➛ select channels at TV (recording continues).

Select Channels at DECK (In STOP or

REC. PAUSE mode),

➛➛

➛ press VCR/TV

(“VCR” lights up on Multi Function Display),

➛➛

➛ select channels at DECK.

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛

➛ press

DVD

, and then press

PLAY

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15)

DECK is plugged in.

If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

Interactive DVD...

May include multiple camera angles,

stories, etc.

Video CD with playback control...

Particular scenes or information can be

interactively selected from a menu that

appears on the screen.

Operation using DECK buttons

Press PLAY.

Insert a disc.

Press

OPEN/CLOSE.

Press STOP.6

Press

POWER

3, 7

OPEN/

SET

FF/

SLOW+

STOP

RETURN

POWER

REW/

SLOW-

NUMBER

keys

TITLE

PLAY

DVD

PAUSE/

STILL

SELECT

SURROUND

SKIP

Press or

NUMBER keys

(see

below) to select title,

and

press

SET

to play.

Press

POWER*

on the remote or DECK.

Press

DVD

to select DVD mode.

Press

OPEN/CLOSE

and then place a disc into the disc tray.

• If a disc is already inserted, go to step 4.

(Depending on the disc, playback may

start automatically.)

Press

PLAY

to start playing.

Disc tray closes automatically.

If an interactive DVD*

a Video CD with playback

control*

is used and TITLE

MENU appears, go to step 5.

• You may also close tray by

pressing

OPEN/CLOSE

• Data reading time differs with

each disc.

Using NUMBER keys starts playing automatically.

<Example> 1 digit number 1 ••• 1

2 digit number 12 ••• 10 1 2

3 digit number 123 •••100 1 2 3

Press

SKIP

| or | to go to next or previous

menu screen.

• SKIP function not available with all discs.

Please refer to disc jacket for operation information.

To return to menu (play stops)

Press

TITLE, MENU,

RETURN

. (DVD)

Press

RETURN

. (Video CD)

Press

STOP

to stop playing.

Press

OPEN/CLOSE

to eject the disc.

• Hold disc by its edges

only (p. 4) with printed

side up and use guides to

place into tray.

Use 3”(8 cm)

or 5” (12 cm) disc.

READING

TLE MENU

Cas

Love

Dogs

TLE MENU

Cas

Love

Dogs

of the world

• Please read the disc jacket for operation

information.

• If a single sided disc is placed in upside

down, “PLEASE CHECK THE DISC, AND

FOR STAINS OR SCRATCHES ON

DISC” is displayed.

• Remove disc and press DECK POWER

off when not in use.

• Disc continues to rotate with menu

displayed even after play is done.

Press STOP to clear menu display when

finished with menu.

■ Forward/Reverse Scene Search

Press

FF/SLOW+

REW/SLOW-

during play.

Press

PLAY

to release.

•Starting forward/reverse search during play

started from menu on Video CDs may recall

menu.

• Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

■ Forward/Reverse Chapter/Track Skip

Press

SKIP

| or |

SKIP

during play.

Each press skips a chapter (DVD) or

track (Video CD/CD).

• Pressing |

SKIP

once midway through a

chapter/track returns to the start of that

chapter/track. Each additional press skips

back one chapter/track.

• Pressing

SKIP

| or | during play started

from menu on Video CDs may recall menu.

■ Still Picture or Pause

Press

PAUSE/STILL

during play.

Press

PLAY

to release.

•DVD/Video CD : DECK will enter still picture

mode.

•CD : DECK will enter pause mode.

■ Frame by Frame Picture

(DVD/Video CD)

Press

PAUSE/STILL

in still mode.

Press

PLAY

to release.

•Each press advances picture one frame.

•Hold button down for consecutive frame advance.

•Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 51)

■ Slow Motion Picture (DVD/Video CD)

Press

FF/SLOW+

REW/SLOW-

in still mode.

Press

PLAY

to release.

•Slow motion speed, slow at first, is increased

with each additional press of the button up to

5 levels.

•Reverse slow motion is not available for Video

CDs.

• When appears on the screen while a button

is being operated, it means that the

corresponding operation is prohibited by DECK

or the disc.

DECK memorizes the point where STOP is

pressed ( flashes on screen).

Press

PLAY

to resume play from this point.

Pressing

STOP

again or opening the tray

cancels RESUME, however, RESUME is not

canceled when power is turned off and on.

• RESUME works only with discs for which

elapsed play time is displayed during play.

Resume Function

Notes

Power turns off after DECK has been in

Stop mode (DVD) for about 5 minutes.

Auto-Power Off Function

1. Do steps 1-4 (previous page).

When menu appears, press

STOP

2. Press

NUMBER keys

to select desired

track (play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,

Press

STOP

and press

PLAY

, then the

menu will be displayed.

Now, go to step 5 (previous page).

Enjoy Video CDs featuring

playback control without using

menus (Video CDs only)

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Surround Sound System

Press

SURROUND

to set Surround sound.

To cancel,

press

SURROUND

• Surround sound effects is available in

DVD mode only.

Note

SURROUND ON

SURROUND OFF

Reverse Skip Forward Skip

Current playback position

Chapter/Track Chapter/Track Chapter/

rack

Chapter/

rack

Basic

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Timer Recording

ADD/DLT

Press PROG*

to display Program.

Press PROG

to end programming.

DAILY

SELECT /

Selection Order

WEEKLY

(SAT)

WEEKLY

(MON)

WEEKLY

(SUN)

Example

Today

2) To set remaining items,

press

to select and

press SET

to set START/ STOP times,

CH(channel) or LINE input

(p. 39), and tape speed

(SP, LP, SLP).

To Enter More Programs,

press

to select and

press SET

to set an unused program

number, and then repeat

step 2.

Press PROG

to exit.

1) To set record DATE,

press

to select:

1~31= one time, or

DAILY= MON~ FRI, or

WEEKLY= same time

each week and

press SET.

• See selection order left.

START

SUN SUN

--:--

DATE START ST

SLP

SELE

SET

END

STA

SPD

13 1013 10

0000

1212

0000

DLT

SELECT 1-8

NTER

: SET

EXIT

POWER

SET

PROG

SELECT

Ready Checklist

All connections are made (pp. 12 ~ 15).

TV and DECK are plugged in.

Clock set correctly.

Tape has rec.tab. (p. 6)

Remote is in VCR mode. (Press VCR.)

Sufficient tape remaining for rec time.

• The “Timer” Indicator lights up on DECK.

• You can do Timer Recording with the power on or off.

• “TIMER REC WILL START SOON” appears on-screen for 2 minutes

before Timer Recording starts. If DECK is in DVD mode, no message

appears, but the VCR REC Indicator, the VCR mode indicator and

“REC” will flash on Multi function Display.

VCR REC Indicator

VCR mode Indicator

VCR

VCR REC

DVD

ANGLE

VCR

Hi-Fi

TIMER

•

Multi Function Display

TIMER Indicator

To Replace program...

To Clear program...

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Important notes when using DSS Receiver

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

DLT

SELECT

1-8 :

ENTER : SET

EXIT

: PROG

STA

SPD

7 9 7 9

0000

12 12

0000

0808

DLT

SELECT

1-8 :

ENTER : SET

EXIT

: PROG

STA

SPD

Press ADD/DLT.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Press

to select number and

press SET

to display.

To cancel a Timer

Recording in progress...

Repeat Step 2 (p. 24)

to set new programs.

Press PROG

to end the programming.

Hold down STOP on VCR mode for

a few seconds to cancel the Timer

Recording.

(The “TIMER” Indicator goes out

on Multi Function Display.)

• Any future daily or weekly recording

will be performed as programmed.

SUN

00A00A

00A

08 08

----------------------------------------

DATE

TART

TOP

SESE

START

SELE

SET

BACK :

END

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to

the Cable Box input channel and Cable Box must be manually set to the desired

channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER

REC” appears and Timer Indicator flashes.

Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be

canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION”

appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back,

Timer Recording will not be performed.

Press PROG

to display Program List.

VCR

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

MONO broadcast

Normal monaural sound broadcast.

SAP broadcast

Secondary Audio Program (sub

language) broadcast. Select SAP

audio mode for the sub language.

MTS Stereo broadcast

Multi-channel Television Sound

Stereo broadcast. Select STEREO

audio mode.

• If stereo broadcast is weak and

display flickers, select MONO audio

mode for possible better results.

MTS Stereo and SAP broadcast

Multi-channel Television Sound

Stereo (main language) and

Secondary Audio Program (sub

language) broadcasts are being

received simultaneously.

Select STEREO or SAP audio mode.

The following are possible audio broadcast types and on-

screen displays.

The signal being received is indicated with an “

” mark

while the selected audio mode is indicated with an arrow.

Receivable Broadcast Types

MTS Broadcast/ VHS Hi-Fi Stereo System

Equipped with

-TV

Noise Reduction for

true MTS reproduction.

-TV Noise

Reduction is required

for good stereo

separation and audio

fidelity.

is a

registered trademark,

and is licensed by

Technology Licensing.

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

To display the broadcast signal being received,

➛➛

➛ press DISPLAY*.

AUDIO

(SAP/Hi-Fi)

DISPLAY

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

Audio Mode for Recording

Do a recording.

See p. 21.

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard

stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to

a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14, 15.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

• Refer to “Receivable Broadcast Types” on p. 26.

• Arrow indicates selection.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

to select desired mode.

STER

SAP

ONO

Notes

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

VCR

Operation

Audio Mode for Playback

Start playback.

See p. 20.

• Arrow indicates

selection.

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo

recordings in stereo sound.

Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

Press AUDIO (SAP/Hi-Fi) repeatedly

to select desired mode.

: L

ORM

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Multi-Brand Control Feature

The Remote Control can be set to control some TV and

Cable Box/DSS functions.

Find your TV and Cable Box/DSS Receiver

Brand Code Number on the following page.

Setup for TV control,

➛➛

➛ hold down TV button,

➛➛

➛ enter code with NUMBER keys.

Multi-Brand Control Setup

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

Setup for Cable or DSS control,

➛➛

➛ hold down DSS/CABLE button,

➛➛

➛ enter code with NUMBER keys.

• If code number is 100 or greater,

➛ e.g., press 1 - 0 - 2 for 102.

• Repeat setup after remote battery replacement.

• Remote will not control every TV, Cable Box, or

DSS made by the manufacturer listed. If you get

no response, your particular unit cannot be

controlled. There are NO additional codes for the

products listed. If your product is not listed, then

the remote is not compatible with that product.

Notes

Mode

Unit

DVD/VCR TV

DVD/VCR

All

POWER, INPUT,

NUMBER keys,

ENTER,

CH / ,

VOL

EJECT/

OPEN/CLOSE

DISPLAY

PLAY

STOP

FF/SLOW+

REW/SLOW-

VCR/TV, PAUSE

/STILL

SKIP

AUDIO

, CA/ZERO,

TAPE POSITION,

COUNTER RESET , SPEED,

REC

After remote is set up, you can select VCR, DVD, TV, or

DSS/CABLE for the desired function.

Press VCR,

DVD

, TV, or DSS/CABLE on the remote.

(Table below shows available remote buttons for each mode.)

CABLE/ DSS

Using Multi-Brand Control

CABLE/

DSS

POWER, ENTER,

NUMBER keys

(except 100key),

CH /

• Not all functions listed may be controllable.

• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing

NUMBER keys for channel selection.

Notes

VOL

VOL +/-

* Bold: VCR Function

Bold Italic: VCR and DVD Functions

Italic: DVD Function

Normal: TV, Cable Box or DSS Receiver

DSS/

CABLE

POWER

ENTER

NUMBER

keys

VCR

DVD

• Due to changes in infra-red commands used by manufacturers, some brands have several

codes. If your unit does not respond to the first code, please try the next one.

• Some TV, Cable Box and DSS Receiver brands require you to turn on the power manually.

Cable Box Brand Code Numbers

Panasonic ....................... 01, 02

Quasar ............................ 01, 02

RCA ....................................... 03

GE ......................................... 03

Zenith .................................... 04

Magnavox.............................. 05

TV Brand Code Numbers

Sylvania ................................ 05

Sharp ............................... 06, 07

Sony ...................................... 08

Toshiba ................................. 09

Sanyo .................................... 10

Fisher .................................... 10

JVC........................................ 11

Hitachi ................................... 12

Mitsubishi ........................ 07, 13

Samsung ............................... 14

Gold Star................... 15, 16, 17

DSS Brand Code Numbers

Important Notes

Archer ......................... 44, 06, 01, 120, 05, 63, 126

Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30

52, 04, 124, 126

Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126

Curtis ..................................... 08, 09, 25, 61, 53, 87

Century ...................................... 44, 51, 75, 59, 126

Cabletenna .................. 29, 09, 01, 63, 120, 44, 126

Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126

Diamond ...................... 29, 09, 01, 63, 120, 44, 126

Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107

Eastern ................................................... 28, 29, 130

Explorer.................................. 08, 09, 25, 61, 53, 87

Gemini .....................................................30, 04, 124

General Electric ......................................01, 57, 120

General Instruments . 01, 84, 83, 34, 03, 02, 04, 55

65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124

Gerrard............................................... 44, 51, 75, 59

GC Electronics ............... 44, 42, 63, 29, 30, 52, 04

124, 126

Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130

Hitachi ................................................................... 31

Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66

67, 68, 120, 106, 121, 122, 115, 117, 118, 124

Jasco ......................................................30, 04, 124

Macom ................................................................... 31

Magnavox...................................................... 26, 112

Matsushita ................................. 17, 16, 08, 87, 109

Movietime ...................... 32, 39, 42, 44, 126, 38, 40

Maestro ........................................................... 74, 35

NEC .................................................... 40, 19, 38, 32

NSC .................................................... 40, 19, 38, 32

Novavision ............................. 08, 09, 25, 61, 53, 87

Next Level...........01, 84, 83, 34, 03, 02, 04, 55, 65

66, 67, 68, 120, 106, 121, 122

Oak................................................. 46, 11, 129, 101

Oak Sigma ..................................... 46, 11, 129, 101

Panasonic .................................. 17, 16, 08, 87, 109

Philips ................... 23, 24, 20, 13, 07, 50, 128, 129

Pioneer......................................................06, 05, 12

Pulsar.................... 04, 42, 63, 44, 30, 52, 124, 126

Quest ........................................................ 06, 05, 12

Radio Shack............................... 44, 51, 75, 59, 126

RCA ............................................ 17, 16, 08, 87, 109

Realistic ..................................... 44, 51, 75, 59, 126

Recoton...................................... 44, 51, 75, 59, 126

Regal ................. 41, 14, 15, 28, 102, 104, 103, 130

Regency ..................................................28, 29, 130

Rembrandt .......44, 42, 63, 29, 01, 32, 39, 120, 126

Samsung ...................................... 42, 06, 32, 05, 40

Scientific Atlanta ................... 08, 09, 25, 61, 53, 87

Sheritech............................................................... 27

Signal ............................................................ 26, 112

SL Marx............. 42, 06, 32, 40, 43, 44, 52, 63, 126

Sprucer ...................................... 17, 16, 08, 87, 109

Standard Components ............... 32, 39, 42, 44, 126

Stargate ..............04, 42, 32, 40, 63, 44, 30, 52, 06

124, 126

Sylvania .......................................................... 19, 18

Teknika ........................................................... 74, 35

Telecaption.................................................... 77, 127

Teleview ................................. 40, 19, 38, 32, 42, 06

Texscan .......................................................... 19, 18

Tocom ...................................34, 33, 01, 42, 66, 120

Toshiba ................................................................. 36

Unika ........................... 44, 42, 63, 29, 01, 126, 120

Universal ..............................52, 43, 44, 63, 42, 126

Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107

Videoway.......................................... 07, 23, 50, 129

Vidtek.................................................................... 64

Zenith ............................................... 07, 23, 50, 129

Toshiba....................................................... 90

Hitachi/ Hughes.................................... 91, 99

Primestar .................................................... 92

Drake .......................................................... 93

Magnavox............................................. 94, 95

Uniden................................................... 94, 95

Optimus ................................................ 94, 95

Panasonic................................................... 96

ProScan...................................................... 97

RCA............................................................. 97

SONY..................................................98, 105

VCR

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Marking

When C/A RECORD: ON, VCR automatically rewinds

the tape after a recording has been made and marks the

beginning and end of any detected commercial blocks.

After marking is done, the tape is returned to the end of

recording. Commercials are not erased from the tape.

Press

to select “SET UP

COMMERCIAL ADV.,”

and press SET to

display.

Press

to select “C/A RECORD,”

and press SET to set

“ON” or “OFF”.

ON Timer Recording and One Touch recordings are marked automatically.

When STOP is pressed during normal recording, Select One of a)

or b) or c).

a) Press 1 key to mark the recording now.

“NOW MARKING COMMERCIALS” appears.

b) Press 2 key to mark the recording later (after the power has

been turned off).

• If the tape is rewound and another recording started before the

power is turned off, commercials may not be marked correctly.

c) Press ACTION to cancel the marking of this recording.

• When using the timer to record two

adjacent shows on the same

channel, better accuracy can be

obtained by programming each

shows separately.

detects and marks the

beginning and end points of commercials on your tape

for recordings over 15 minutes in length.

When

marked tape is played

back, the VCR automatically advances through the

commercial segments at high speed. You can also set

this feature to Manual so as to have more control over

the advance process. The effectiveness of this system

can vary due to differences in the way television stations

broadcast. See page 32 for answers to the most

commonly asked questions about this feature.

OFF The VCR will not mark commercials.

When you are editing or dubbing a tape, or when you do not wish to use this feature,

OFF should be selected.

Press ACTION twice

to return to normal screen.

Tape Operation

Note

Ready Checklist

All connections are made.

One time Setup completed.

VCR is plugged in.

TV is turned on and set to CH3, 4

or Video on TV.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

SELE

SET

EXIT

ACT

SET UP COMMERCIAL ADV.

C/A RECORD

:ON

C/A PLAYBACK

:AUTO

THE VCR IS WAITING TO

MARK COMMERCIALS IN THE

PROGRAM YOU RECORDED.

MARKING

NOW : PRESS 1

LATER

: PRESS 2

CANCEL : PRESS ACTION

SET

NUMBER

keys

SELECT

ACTION

Press ACTION*

to display MENU.

Playback

When playing back recording which have been

marked using

feature, you can

either set VCR to automatically advance through

marked commercial blocks, or set it so that

commercials are only skipped on your command.

AUTO : VCR will automatically advance through

marked commercial blocks recorded on the

tape and then resume playback.

MANUAL: VCR will advance through commercials only

when CA/ZERO is pressed. Playback will

resume when the end mark of a commercial

block is found, or a new recording or blank

portion is detected, or after 8 minutes.

• The selection mode in step 3 remains set unless there is a power outage in which case the

original factory setting will be restored.

• If playback is started in the middle of a commercial, only a single commercial is shown, or an

individual commercial is longer than 1 minute, a commercial may not be skipped.

Press FF to quickly advance through the commercial.

• Part of a recorded program may be skipped over if the program portion between commercials

is less than 1 minute or there are frequent dark and quiet scenes during the program. To view

the portion of tape being incorrectly skipped, press PLAY while the VCR is skipping, reverse

the tape to a point just prior to where the skipping began and press PLAY again. This time the

group will not be automatically skipped. Automatic skipping will be re-enabled when the end of

the marked group is detected.

Press ACTION twice

to return to normal screen.

PLAY

*Important: If a remote control button does not work when pressed, press

the VCR button on the remote and try the button again.

and

are

registered trademarks of SRT, Inc.

A Jerry lggulden invention licensed

in association with Arthur

D. Little Enterprises, Inc.

U.S.Pat. No. 5,333,091;

5,692,093; 5,696,866

other patents pending

Notes

VCR

Operation

SET

NUMBER

keys

SELECT

ACTION

CA/ZERO

Press

to select “SET UP

COMMERCIAL ADV.,”

and press SET to

display.

Press

to select “C/A

PLAYBACK,”

and press SET to set

“AUTO” or “MANUAL”.

Press ACTION

to display MENU.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

SELE

SET

EXIT

ACT

SET UP COMMERCIAL ADV.

C/A RECORD

:ON

C/A PLAYBACK

:AUTO

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Tape Operation (continued)

The most commonly asked questions about are answered below.

Question

How fast does the VCR advance

through commercials?

Are commercials advanced through only

when I playback a recording?

Are commercials still recorded on the

tape in case I choose to view them

sometime?

Does work in

all recording speeds?

Does the VCR advance through

commercials each time I playback tapes

which were recorded using

After marking commercials, does the

VCR stop at the end of the tape, or

rewind to the beginning?

Can I play my

recordings in non-

VCRs?

Does the marking process interfere with

other programmed recordings?

What happens if I cancel the marking in

progress so I can use the VCR?

What if part of my program is advanced

through along with the commercials?

Answer

The VCR advances through a 3-minute commercial

block in about 8 to 12 seconds if the tape speed is

SLP. In SP, it takes about 25 to 35 seconds.

Yes. The commercials are not marked until after the

recording is finished.

Yes. By setting the C/A PLAYBACK to MANUAL (see

page 31), you can view or advance through

commercials as desired.

Yes. works in SP, LP, and

SLP.

Yes. As long as C/A PLAYBACK is set to AUTO (see

page 31), the VCR should advance through

commercials each time the tape is played back.

The tape stops at the end of the recording so that

any additional timer recordings can be performed.

Yes. marked recordings will

play in non- VCRs, but

commercials will not be advanced through.

No. If the interval between 2 or more timer programs

is not sufficient to mark the recording, marking will be

done after all recordings are complete and the power

goes off.

Marking will be resumed when the VCR's power is

turned off as long as the tape has not been ejected.

Please see the 3rd note on page 31.

Additional Notes:

• Because of the various ways in which commercials are broadcast, the VCR may not be able

to recognize all commercials.

• If a timer recording is scheduled for the middle of the night, please be aware that the VCR will

make some noise as it rewinds and fast forwards the tape while marking commercials.

and are registered trademarks of SRT, Inc.

A Jerry lggulden invention licensed in association with Arthur D. Little Enterprises, Inc.

U.S.Pat. No. 5,333,091;

5,692,093; 5,696,866

other patents pending

helps you locate certain

parts of prerecorded movies (rented or

purchased). The feature works in two ways.

• You can go to the beginning of the movie.

• You can skip from one preview to the next.

works only on tapes

recorded in SP speed with the record tab

removed.

Insert a tape

without record tab.

Press SEARCH/ M/A SKIP* three times to

display MOVIE ADVANCE.

Select “GO TO START MOVIE,” if you want

to advance directly to beginning of the

movie.

➛➛

➛ continue with step 4.

Select “GO TO PREVIEW,” if you want to

view the first (next) preview.

➛➛

➛ go to “To Search for Preview” at right.

Press FF

to start searching.

• To cancel,

press STOP.

Press PLAY

to start playback.

When the movie is found...

• To cancel,

press STOP.

Start preview searching.

When a preview is detected, VCR

will start playback.

To Search for Preview.

Start next preview searching.

1) In step 3 at left, select “GO

TO PREVIEW.”

2) Press FF.

Press SEARCH/ M/A SKIP.

• To cancel, press STOP.

You can override the operation of

SEARCH FOR

PREVIEWS mode by pressing SEARCH/ M/A

SKIP during tape searching.

works by searching

the tape past each preview and then reversing

back to the start of the detected preview.

While the tape is reversing back, if SEARCH/ M/

A SKIP is pressed,

will

begin searching for the next preview.

While searching for the next preview, if you see

the start of a preview which you wish to watch,

press SEARCH/ M/A SKIP and

will immediately

reverse back to the start of that preview,

instead of searching further past the preview

start point. Once the VCR is playing a preview,

press SEARCH/ M/A SKIP to advance to the

next preview, long commercial or the start of

the movie (whichever is next).

• If you want to playback, press PLAY.

Press to select

“GO TO START

MOVIE” or “GO TO

PREVIEW.”

*Important: If a remote control button does not work when pressed, press

the VCR button on the remote and try the button again.

Ready Checklist

All connections are made.

One time Setup completed.

VCR is plugged in.

TV is turned on and set to CH3, 4

or Video on TV.

GO TO START MOVIE

GO TO PREVIEW

SEARCH START : FF

SELECT

EXIT :

SEARCH M/A SK

MOVIE ADVANCE

SEARCHING FOR START

OF MOVIE

CANCEL :

STOP

MOVIE ADVANCE

THE MOVIE IS READY

START :

PLAY

CANCEL :

STOP

MOVIE ADVANCE

VCR

Operation

SET

STOP

SELECT

SEARCH/

M/A SKIP

PLAY

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Index Search

Note

• If Index Search is started very close to an

index mark, that index mark may not be

counted in the search.

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and

information are also included for timer recordings. These marks are used to access or

scan recordings.

Program End Search

Fig. 1

Fig. 2

Fig. 3

Note

Locates end point of recording for continuity.

Examples of Program End Search.

If search exceeds

a few seconds in

BLANK area.

➛➛

➛ search continues 7 sec. past end point,

➛➛

➛ tape rewinds to 10 sec. before end point,

➛➛

➛ tape plays to end point and stops.

Upon locating end point,

• If Program End Search is started very close to

an index mark, that mark may be skipped over.

PROGRAM END SEARCH

SEARCH START : FF

EXIT

:SEARCH

Program 2 or BLANK

Program 1

the current tape position

Press SEARCH button

INDEX

End Point

Program 2

Program 1

the current tape position

Press SEARCH button

INDEX

BLANK

End Point

Program 2

Program 1

the current tape position

Press SEARCH button

BLANK

INDEX

End Point

INDEX SEARCH

ENTER INDEX NUMBER :1

USING

9 KEYS

FORWARD SEARCH :FF

REVERSE

SEARCH :REW

NEXT :SEARCH/ M/A

EXIT

:STOP

INDEX SEARCH

FORWARD SEARCH : FF

REVERSE

SEARCH : REW

Press SEARCH/

M/A SKIP*

to display SEARCH

in Stop or Play

mode, and then

press NUMBER

keys

to select recording

number.

• To calculate

number, see below.

Press FF/SLOW+

or REW/SLOW- on

the remote to start

search.

Press SEARCH/ M/A SKIP twice

to display SEARCH in Stop or Play

mode.

Press FF/SLOW+

on the remote to

start PROGRAM

END SEARCH.

• To cancel, press

PLAY or STOP.

Play begins at

search end.

To search forward

or back 1 index,

press FF/SLOW+ or

REW/SLOW- on the

remote while

screen left is

displayed (10 sec.).

• To cancel, press

PLAY or STOP.

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

NOTE: indicates start points of each recording.

61572 34

17534 62

Auto Play

Insert a tape ➛ Power comes on,

➛ Play starts if no record tab

(see p. 6).

Auto Rewind

Play

Fast Forward

Play Auto Eject

(Repeat Play must be off)

Play

➛ ➛

➛ Tape end

➛ ➛

➛ Rewind

➛ ➛

➛ Tape ejects if no record tab

Auto Operation Functions

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

REW/SLOW-

FF/SLOW+

PLAY

SEARCH/

M/A SKIP

NUMBER

keys

CA/ZERO

STOP

VCR

Operation

➛ Tape end ➛ Rewind

Zero Search

To quickly return to a specified tape location.

Continue to record, playback etc.

Press STOP.

• DECK will go into FF or REW mode and stop

at the last point the Counter was set to 0:00:00.

PLAY

Press DISPLAY during play

to display Counter.

Press COUNTER RESET

at desired position to reset

to “0:00:00”.

Press CA/ZERO in Stop

mode to start Zero Search.

REW

STOP

COUNTER

RESET

DISPLAY

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Tape Operation (continued)

Repeat Play

Set to playback a recording over and over.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

Press ACTION*

to display MENU.

Press

to select “SET UP VCR,” and

press SET.

• Play repeats at tape end or if unrecorded portion

over 30 sec. is detected.

Press ACTION twice

to return to normal screen.

ACTION

SET

Press

to select “REPEAT PLAY,”

and press SET

to set “ON” or “OFF.”

REPEAT

PLAY

OTE

ARN

AUT

SHU

OFF

SELE

SET

END

ACT

SET

UP V

SELECT

Note

• For repeat play in DVD mode, see page 46.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

ACTION

SET

Special VCR Features

SELECT

*Important: If a remote control button does not work

when pressed, press the VCR button

on the remote and try the button again.

When set to ON, all operations

except for timer record and tape

eject are prohibited. Useful for

households with small children.

VCR Lock Feature

K ACT

TED

• VCR Lock cancels in 24 hours if

clock is set.

To turn off, repeat above.

To turn on, hold down REC on

DECK in Stop mode with no

tape inserted for 7 seconds.

(Please ignore “NO CASSETTE”

warning.)

REC

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

VCR

Operation

Weak Signal Display Feature

When “ON,” picture is displayed regardless of signal

strength.

• ON: Picture is displayed regardless of signal

condition, and may not always be clearly visible.

OFF: Screen turns solid blue when signal is weak or

non-existent.

• Selecting ON has no effect on connected equipment

with blue back feature.

Press ACTION twice

to return to normal screen.

Press

to select “SET UP

CHANNEL,” and

press SET.

Press

to select “WEAK SIGNAL

DISPLAY,” and

press SET

to set “ON” or “OFF.”

Press ACTION

to display MENU.

Auto Shut-Off Feature

The power shuts off at a preset time.

Press

to select “AUTO SHUT-OFF.”

Press SET repeatedly to

change shutoff time as

shown below.

Press ACTION twice

to return to normal screen.

Press ACTION

to display MENU.

Press

to select “SET UP VCR,” and

press SET.

• The shut-off countdown will not

function during Play or Record.

Note

SELE

SET

EXIT

ACT

ANT

ENN

ABLE

SPLA

OFF

SET UP

NNE

REPEAT

PLAY

OTE

ARN

AUT

SHU

OFF

SELE

SET

EXIT

ACT

SET

UP V

OFF

2 Hours

6 Hours

4 Hours

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Special VCR Features (continued)

INPUT

ACTION

SET

TAPE

POSITION

SELECT

If Multi-brand feature is used (p. 28), and this feature is

set to on, a warning appears whenever an invalid key

is pressed in TV, DSS or CABLE mode.

• If “OFF,” remote warning will not appear

when invalid key is pressed.

Press ACTION*

to display MENU.

Press

to select

“REMOTE WARNING,” and

press SET

to set “ON” or “OFF.”

Press ACTION twice

to return to normal screen.

Remote Warning Feature

Press

to select “SET UP VCR,”

and

press SET.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SET UP C

OMM

ADV.

IDIOMA/LANGUE : ENGL

VCR’S OUTPUT CH:3

REPEAT

PLAY

OTE

ARN

AUT

SHU

OFF

SELE

SET

EXIT

ACT

SET

UP V

*Important: If a remote control button does not work

when pressed, press the VCR button

on the remote and try the button again.

PAUSE/

STILL

STOP

REC

To find out the present tape position and amount of tape remaining.

Tape position is displayed for VHS-C Cassettes type, tapes

under 30 minutes, and some other tapes, but the position is

not correct.

• Tape remaining time display may not be

precise.

END

R 120 M

• “DETECTING TAPE POSITION” is displayed

only when a cassette is first inserted, and it

takes several seconds for correct tape

position to appear.

Tape Position and Tape Status Feature

Press TAPE POSITION

to return to normal screen.

• The present tape position indication and

amount of tape remaining (according to

tape speed) is displayed.

DETECTING TAPE POSITION

Press TAPE POSITION

to detect current tape position.

This function cannot display exact amount of tape remaining for

tapes 30 minutes or less, or for tapes over 120 minutes in length.

Note

Copying Your Tapes (Dubbing)

Insert a pre-recorded tape.

Insert a blank tape with record tab.

Press REC, then PAUSE/STILL

immediately to enter REC/PAUSE

mode.

Press INPUT to set DECK Input mode to

LINE for Video Input.

(See “Selecting the Input Mode” below.)

Press PLAY to start dubbing.

Playing VCR starts playback.

Press PAUSE/STILL to start dubbing.

DECK starts recording.

Press STOP to stop dubbing.

Caution:• Unauthorized exchanging and/or copying of copyrighted recordings may be

• Please note that some tapes cannot be dubbed on DECK. Also, it is not

possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.

Playing (Source) VCR Recording (Editing) DECK

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording

VCR channel (CH 3 or CH 4).

2 Set the VCR/TV Selector on DECK to

“VCR.”

Note

• Dubbing tapes protected with Copy

Guard will have poor quality results.

Connection

Press STOP to stop dubbing.

Press PLAY, then PAUSE/STILL

immediately to enter PLAY/PAUSE

mode.

The operation of steps 4 and 5 must be done on both

playing and recording VCRs at the same time.

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.

To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R”

AUDIO IN terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder.

Simply connect the unit’s Audio/Video outputs to DECK.

Selecting the Input Mode

Method 1: Press INPUT repeatedly.

Channel Number

↔↔

↔ LINE1

↔↔

↔ LINE2

Method 2: Press CH / .

Display will change as below.

Front of DECK

VIDEO IN 2

L-AUDIO IN2-R

(Audio/Video In Terminals

on the front of DECK are

available)

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

VHF/

UHF

DVD/VCR DECK

VIDEO

AUDIO

VCR/ Camcorder (Hi-Fi)

VIDEO

AUDIO

• “L1” or “L2” lights up on Multi Function Display

(about 4 seconds) when LINE1 or LINE2 is selected.

• LINE1: For rear audio/video connection.

LINE2: For front audio/video connection.

VCR

Operation

125

LINE1

(CABLE)

(TV)

LINE2

Press

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

AUDIO:3 ESP

Dolby Digital 3/2.1ch

SELECT : SET:SET

Hola

AUDIO:1 ENG

Dolby Digital 3/2.1ch

SELECT

: SET:

SET

Hello

ESP

Te amo

• If after several presses of the button the language does not

change, language selection is not offered on the disc.

• When power is turned on again or disc is removed, subtitles

revert to initial setting language. If the initial language is not

recorded on the disc, the disc’s priority language will appear.

You can select a different subtitle language (if offered) than

the one set at the Settings for DVD Operation.

(See p. 49.)

Press

to select a language.

Press

(or )

to set.

Press

to select “ON” or “OFF.”

Subtitle Language (DVD only)

• Display disappears after

5 seconds.

• When no subtitles are offered,

“-” will be displayed instead of

the language number.

Press

SUB TITLE

in Play mode to display

the subtitle selection

on-screen.

ENG

FRA

DEU

ITA

ESP

NLD

English

French

German

Italian

Spanish

Dutch

SVE

NOR

DAN

POR

RUS

JPN

Swedish

Norwegian

Danish

Portuguese

Russian

Japanese

CHI

KOR

MAL

VIE

THA

∗

Chinese

Korean

Malay

Vietnamese

Thai

Other

[Subtitle language (No.)]

[Audio sound track language (No.)]

• Change the No. by pressing ,

and press

SET

Ready Checklist

Please read “Basic DVD Operation”

on p. 22.

You can change the audio soundtrack language, selected

at the Settings for DVD Operation, to a different language

if available. (See p. 49.)

(This operation works only with discs on which multiple

audio soundtrack languages are recorded.)

Press

AUDIO

in Play mode to display the

audio selection on-screen.

Audio Soundtrack Language (DVD only)

Audio attribute 1 type,

sampling frequency, bit No. of

the disc.

[Audio attribute 1 type, sampling

frequency, bit No. of the disc (see

p. 50.)]

Disc Operation

Number of subtitle language being played back.

Press

to select desired language.

Number of the audio soundtrack

language being played back.

• If, after several presses of the

AUDIO button the language does not

change, language selection is not

offered on the disc.

• When power is turned on again or

disc is removed, language reverts to

initial setting. If this language is not

recorded on the disc, the language

recorded will be heard.

LPCM

Dolby Digital

DTS

96KHz

48KHz

1ch - 5.1ch

16bit

20bit

24bit

Linear PCM disc

Dolby Digital disc

DTS disc

Notes

• Display disappears after

5 seconds.

When appears on the screen while

a button is being operated, it means

that the corresponding operation is

prohibited by DECK or the disc.

• The ANGLE Indicator lights up on

DECK when a scene recorded

at different angles is detected.

• The angle number can be set

beforehand so that the angle is

switched whenever the ANGLE

Indicator lights up.

ANGLE Indicator

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1

V2 VOCAL V1 VOCAL V2 VOCAL OFF

• Video CD LR L R

Press

AUDIO

in Play mode

to display the audio screen.

Vocal Selection for Karaoke Discs

(DVD/Video CD)

DVDs may contain scenes shot from multiple camera

angles allowing the same scene to be viewed at different

angles. You can view these angles, if available, using the

ANGLE button.

Press

ANGLE

in Play mode to display the

angle selection on-screen.

• Display disappears after

5 seconds.

Multiple Angle Viewing (DVD only)

Press

to select the desired

angle.

Press (or )

to select as shown below,

and

press

(or ) to set.

(DVD only)

Number of angle being played back.

ANGLE : 1ANGLE : 1

SELECTSELECT : : SESET:T:SETSET

SELECT : SET:SET

AUDIO:2 ENG VOCAL ON

VOCAL ON

You can enlarge specific portions of a picture and

select the zoom ratio using the ZOOM button during

DVD playback.

Press

ZOOM

repeatedly to change display

as follows.

Picture Zoom (DVD only)

• You can enlarge the center portion of the image

to one of 2 magnifications.

• The subtitle cannot be enlarged nor

can it’s position be changed.

• The picture zoom feature does not

work with a Video CD.

• During picture zoom, “ZOOM1” or

“ZOOM2” is displayed on-screen.

• Zooming, on some discs, may result

in poor picture quality, or may not

operate at all.

■ Use the , , and buttons to move the position

up, down, left and right.

Notes

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

AUDIO

SET

ANGLE

SUB TITLE

ZOOM

SELECT

DVD

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Some DVDs have more than one title, e.g. movies.

If the disc offers a title menu, you can select the desired

title number. (Operation may vary according to the disc.)

Press

TITLE

in Play mode

to display the title screen.

Title Menu (DVD only)

DVDs may offer a special menu. This menu may include

guides to unique contents, audio/subtitle languages, etc.

Although contents and operation may vary, the following

steps show basic steps for using the menu.

Press

in Play mode to display

DVD MENU.

Press or

NUMBER keys

to select an item, and

press

SET

PLAY

to perform.

DVD Menu (DVD only)

Press or

NUMBER keys

to select a title, and

press

SET

PLAY

to start playing.

Disc Operation (continued)

• “Pressing

SET

PLAY

” is

not necessary when using

NUMBER keys.

T I TLE MENU

Cas

Love

Dogs

TLE MENU

Cas

Love

Dogs

DVD MENU

3 . ANGLE

1 . SUBT

TLE

2 . AUD

DVD MENU

3 . ANGLE

1 . SUBT

TLE

2 . AUD

rds

of the world

Repeat step 2 if there is

more than one menu.

• “Pressing

SET

PLAY

” is

not necessary when using

NUMBER keys.

SET

STOP

PLAY

NUMBER

keys

TITLE

CLEAR

ACTION

SELECT

You can program specific tracks and order of play.

Program Play (Video CD/CD)

Ready Checklist

DECK is in DVD mode, press DVD.

Video CD or CD is inserted.

Press

ACTION

to display MENU.

Press

to select

“PLAY MODE,” and

press

SET

to display.

Press

to select

“PROGRAM PLAY,”

and

press

SET

to display.

Press

to select “START,” and

press

SET

to start play

of programs in the

sequence selected.

• To cancel, press

STOP

during play, then press

CLEAR

Press

to select a track

number (Track

numbers on disc are

displayed.), and

press

SET

• Repeat step 4 to select another track.

• The selected track is added on the right side.

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STI LL MODE : FIELD

TV MODE : Letterbox 4:3

PARENTAL

LOCK

LEVEL 8

PLAY MODE

SELECT :

SET : SET

END : ACTION

PROGRAM PLAY

RANDOM PLAY

SELECT :

SET : SET

END : ACTION

DISC PROGRAM

1 61116 5 8

2 7 12 17 15 6

3 8 13 18 1 13

4 91419 3 2

5101520 2

CLEAR LAST

CLEAR ALL START

PROGRAM PLAY

SELECT :

SET : SET

END : ACTION

DISC PROGRAM

1 61116 5 8

2 7 12 17 15 6

3 8 13 18 1 13

4 9 14 19 3 2

5101520 2

CLEAR LAST

CLEAR ALL START

Notes

Program Repeat Play

(Video CD/CD)

Press

SET

to enter Select mode.

“REPEAT OFF” will flash.

Press to select “DISC

REPEAT.”

(DECK Information Screen)

Do operation steps 1 through 5

at left on this page.

Press

DISPLAY

to display Disc

Information screen.

(Disc Information Screen)

Press

DISPLAY

to display

DECK Information screen.

Press

SET

to set mode. (“DISC

REPEAT” will stop flashing.)

To cancel, select “REPEAT

OFF” in step 5, then press

SET

SELECT:

SET : SET END : DISPLAY

PLAY

DISC REPEAT

PROGRAM PLAY

SET : SET END : DISPLAY

PLAY

REPEAT OFF

PROGRAM PLAY

SET : SET NEXT :DISPLAY

TRACK

: 1 VIDEO CD

PBC : OFF 1 :35: 12

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

• Up to 15 tracks can be programmed.

•“ ” or “ ” (depending on disc) indicates additional

PROGRAM PLAY screen.

Press for next or previous screen.

• To clear the last program one by one

Press to move to “CLEAR LAST” and

press

SET

. (Pressing

CLEAR

on remote control

also clears last program.)

• To clear all programs

Press to move to “CLEAR ALL” and press

SET.

(Programs are also cleared when the power

is turned off or the disc is removed.)

DVD

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Tracks are played in a random order.

Random Play (Video CD/CD)

Press

ACTION

to display MENU.

Disc Operation (continued)

Pess

to select “PLAY MODE,”

and

press

SET

to display.

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STILL MODE : FIELD

TV MODE : L etterbox 4:3

PARENTAL

LOCK

LEVEL 8

PLAY MODE

Press

to select

“RANDOM PLAY,” and

press

SET

to begin random play.

• To cancel, press

STOP

during play, then press

CLEAR

PLAY MODE

SELECT :

SET : SET

END : ACTION

PROGRAM PLAY

RANDOM PLAY

*Important:

If a remote control button does not

work when pressed, press the

DVD button on the remote and try

the button again.

SELECT

STOP

CLEAR

ACTION

SET

AUDIO

CONTROL

Ready Checklist

DECK is in DVD mode, press DVD.

Setting the Sound Output Level

Press

AUDIO CONTROL

repeatedly to change “ON”

↔↔

↔ “OFF.”

• “ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when

press AUDIO CONTROL.

DVD /Video CD

Music CD

Audio Control “OFF”

Volume level is low.

Audio Control “ON”

Volume level is increased

automatically when played back.

• “ON” is set ..... When a DVD or Video CD is played back, the average volume is increased.

• “OFF” is set.... The volume level recorded on the disc is played back just as it is.

• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.

• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”

Notes

Audio recorded on a DVD or Video CD often incorporates

a dynamic range of sound.

This means that, when compared to a music CD, etc.,

the average volume is generally lower and the peaks

may be higher. This unit can be set so that the average

volume is increased automatically.

SET : SET NEXT:DISPLAY

TRACK : 12 VIDEO CD

PBC : OFF 0:12 :34

SELECT:

SET : SET NEXT:DISPLAY

TITLE : 12 DVD

CHAPTER: 11 0:12:34

Press

DISPLAY

in Play or Stop mode

to display “On-Screen Displays.”

When

DISPLAY

is pressed, On-Screen Displays show

disc information (title/chapter/track number, elapsed

playing time) and DECK information (repeat play, play

mode).

• Each press of

DISPLAY

changes the on-screen

display as follows. (refer to p. 46.)

DISPLAY

button does not function while DVD

TITLE MENU is displayed.

Note

Press

to select the setting, and

press

SET

To make corrections,

press

and

SET

repeatedly to move to

the error, then correct.

• Pressing is effective

for elapsing time

instead of the above

buttons. Press

repeatedly to delete the

error, then correct.

• For some functions the

setting will be registered

immediately without

pressing

SET

• When numbers are

displayed (e.g. title

number),

NUMBER keys

are also available.

To return to normal

screen,

press

CLEAR

DISPLAY

repeatedly.

Press (or )

to select

an item, and

press

SET

Notes

• When

DISPLAY

button is

pressed during playback of a

Video CD with Playback control,

NUMBER keys

are not available

on the displayed screen. In this

case, press

DISPLAY

again to

remove the displayed screen.

• When appears on the screen

while a button is being operated,

it means that the corresponding

operation is prohibited by DECK

or the disc.

SET

NUMBER

keys

DISPLAY

SELECT

DVD Operation using On-Screen Displays

Selected disc information

Selected DECK information

Normal Screen

CLEAR

SELECT:

SET : SET NEXT :DISPLAY

TITLE : 12 DVD

CHAPTER

: 2424 0:12:34

SET : SET NEXT:DISPLAY

TRACK : 17 VIDEO CD

PBC : OFF 0:12 :34

Ready Checklist

DECK is in DVD mode, press DVD.

DVD

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

SELECT:

SET : SET NEXT :DISPLAY

TITLE : 1 DVD

CHAPTER: 12 1: 12: 55

DVD Operation using On-Screen Displays (continued)

Detailed Descriptions of each On-Screen Display

■■

■ Disc information screen (for DVD)

1. TITLE No.

• Change the No. by pressing * or

NUMBER keys

, and press

SET

2. Chapter No.

• Change the No. by pressing or

NUMBER keys

, and press

SET

3. Disc currently being played

4. Elapsed playing time

The screen may be changed by selecting the elapsed time.

•Change the elapsed time by pressing

NUMBER keys

e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

•This function does not work with some discs.

■■

■ Disc information screen (for Video CD/ CD)

A.Track No.

• Change the No. by pressing or

NUMBER keys

, and press

SET

B.Playback control ON/OFF

[Video CD with playback control only]

C.Disc currently being played

D.Elapsed playing time

• Track No. and the elapsed playing time are not displayed during play started from menu of Video

CDs with playback control.

• When appears on the screen while a button is being operated, it means that the corresponding

operation is prohibited by DECK or the disc.

OFF Video CD menu play is cleared.

ON Video CD menu play is displayed.

Video CD CD

Note

SET : SET NEXT :DISPLAY

TRACK : 1 VIDEO CD

PBC : OFF 1 :35: 12

a. Repeat Play

■■

■ DECK information screen (for DECK)

• Change the desired mode during play by pressing , and press

SET

b. Play mode [Video CD/ CD only] (See p. 43 or 44.)

Video CD/CD TRACK REPEAT DISC REPEAT REPEAT OFF

DVD CHAPTER REPEAT TITLE REPEAT REPEAT OFF

PROGRAM PLAY program play

RANDOM PLAY random play

----

normal play

SELECT:

SET : SET END : DISPLAY

PLAY

CHAPTER REPEAT

SET : SET END : DISPLAY

PLAY

DISC REPEAT

RANDOM PLAY

TITLE

chapter

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

track

TRACK REPEAT

DISK REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

•

CHAPTER/TITLE REPEAT PLAY (DVD)

•

TRACK/DISC REPEAT PLAY (Video CD/CD)

For your reference

• For repeat play in VCR mode, see p. 36.

Note

DVD

Operation

MP3 Playback Operation

*Important: If a remote control button does not work

when pressed, press the DVD button on

the remote and try the button again.

Press

POWER

on the remote or DECK.

Press

OPEN/CLOSE

and then place a MP3 disc into the disc tray.

Press

OPEN/CLOSE

to close.

MP3 Playback

MP3 MENU is displayed and playback is

started automatically.

(The MP3 CD directory is

displayed.)

You can use this unit to play MP3 format audio recorded for

personal use with a computer etc. onto a CD-R or CD-RW.

Play may not be possible in some cases due to the

condition of the recording.

PLAY

PLAY MODE : NORMAL

MP3

ROOT

. .

VAVA

END

ALTZ

TECHNO

CUB I C

POPS

CTURNE

AZZ

ROOT

TECHNO

POPS

AZZ

END

ALTZ

DD_CUB I C

CTURNE

Function

Status

Counter

PLAY MODE

Folder area

File area

Parent

folder

(The currently

displayed folder

turns green)

(The selected

MP3 file/folder

is displayed

with a cursor.)

(The MP3 CD directory structure

displayed in the above example OSD

is shown in the diagram at left.)

: MP3 file

: Folder

: Parent folder

■ Forward/Reverse Search

Press

FF/SLOW+

REW/SLOW-

during play.

Press

PLAY

to release.

•Search speed, slow at first, increases with each

additional press of the button up to 4 levels.

■ Forward/Reverse Track Skip

Press

SKIP

| or |

SKIP

during play.

Each press skips a track.

•If pressed within first 3 seconds of playback, skips

to the previous track. If over 3 seconds, returns to

first of that track. (|

SKIP

only.)

•Only the

SKIP

| or |

SKIP

button can be used

for track skip selection during playback.

Place unit into Stop mode before performing folder/

file selection (see above right.)

Press

STOP

to stop playing.

Press

OPEN/CLOSE

to eject the disc.

The MP3 MENU is closed automatically.

[PLAY MODE]

NORMAL:

All MP3 files are selected and

played back one time only.

SINGLE REPEAT:

The selected MP3 file is

played back repeatedly.

FOLDER REPEAT:

The MP3 files contained in

the selected folder are played

back repeatedly.

However, folders below the

selected folder are not played

back.

DISC REPEAT:

All MP3 files are played back

repeatedly.

■ MP3 playback (During STOP mode)

1)Press

to select an MP3 file ( ).

2)Press

SET

PLAY

to start playback.

■ Select folder (During STOP mode)

1)Press

to select a folder ( ).

2)Press

SET

to display files/folders

contained in the folder.

■ Select parent folder (During STOP

mode)

1)Press

to select a folder ( ).

2)Press

SET

to make changes to

the previous directory display.

■ Select PLAY MODE (During STOP

mode)

1)Press

to move cursor to PLAY

MODE.

2)Press to select the desired

PLAY MODE (see below).

• Folder area operation cannot be done.

Only file area operation is possible.

Note

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

DVD Lock (DVD only)

LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs and

Video CDs is prohibited.

(Use to prohibit play of mature theme DVDs not

encoded with rating level.)

LEVEL 1 : mature theme DVDs

LEVEL 2 : DVDs expressly for children can be played back.

LEVEL 3 to 7 : DVDs for general audiences/children can be

played back. (DVDs with mature content

are prohibited.)

LEVEL 8 : NO LIMIT: (Factory preset)

All DVDs can be played back.

You can prevent playback of DVDs of a specific

rating level which may be unsuitable for children.

• Some DVDs are encoded with a rating level. If the disc

rating is higher (stricter) than the one you preset,

playback will be prohibited.

After DVD Lock is set and a

blocked DVD is played, this

message will appear.

The message may differ

depending on the disc.

To continue viewing a blocked

program for now,

Press to select “YES” and

SET. Then, enter your 4 digit

secret code. When “NO” is

selected, blocked programs

cannot be viewed.

DVD Lock Feature

SELECT:

SET : SET END : DISPLAY

YOUR SELECTION EXCEEDS THE

PLAYER S RATING LIMIT.

DO YOU WANT TO CHANGE THE

LIMIT?

YES

Discs not encoded with rating

level will play even if the jacket

states it is for mature

audiences. For these discs, the

DVD Lock Ratings will not work.

Caution

Press

to select rating level, and

press

SET

to select “LOCKED” or

“UNLOCKED.”

Press

ACTION

twice

to end setup.

A 4-digit code must be entered to view a blocked

program or change rating settings.

Press

ACTION

to display MENU.

Press

to select “PARENTAL LOCK,”

and

press

SET

to display.

1) Press

NUMBER keys

to enter your secret code.

2) Enter same secret code

again for confirmation.

3) Press

SET

to display.

• Step 2) not necessary when

changing rating or secret

code.

• Take care that you are not

observed entering the

secret code.

To Make Corrections

Press repeatedly to

move the cursor.

Press

NUMBER keys

make the correction.

Change your secret code

• You will need your current code.

Do step 1 ~ 2 left.

Enter current secret code.

Press

CLEAR

to clear the code.

Do step 4 to enter new code.

• DO NOT forget your secret code.

Note

END

ACT

ENTER

ENTER 4

CODE

----

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STILL MODE : FIELD

TV MODE : Let terbox 4:3

PARENTAL LOCK : LEVEL 8

*Important: If a remote control button does not work when

pressed, press the DVD button on the remote

and try the button again.

Ready Checklist

DECK is in DVD mode, press DVD.

Disc Languages (DVD only)

To select and set the language of the audio

soundtrack, subtitles, or title/DVD menus for all discs

to be played.

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese

Original: Original disc language

OTHER ✱✱✱✱: Other language selection*

“SUBTITLE” selections

(Factory preset: AUTO)

To select the subtitle language.

AUTO: Same language selected

for “AUDIO”

• If language set for “AUDIO” is used in

playback, subtitles will not appear.

• If another language is used during

playback, the subtitles will appear

in the language selected at “AUDIO”

setup.

English/Spanish/French/Japanese

OTHER ✱✱✱✱: Other language selection*

“MENUS” selections

(factory preset: English)

To select the language used in title

menus or DVD menus.

English/Spanish/French

/Japanese

OTHER ✱✱✱✱:

Other language selection*

To enter OTHER ✱✱✱✱

code

number,

Press

NUMBER keys

(Please refer to

language codes on p. 52).

To make corrections, press

repeatedly to delete language code

number, and correct.

Settings for DVD Operation

Once initial settings are done, they

remain in memory (even after power off)

until changed. This means DECK will

operate under the same conditions

(especially DVDs) each time.

DISC LANGUAGES (See below)

All languages offered on the disc can be set.

If the language not offered is set, the original disc

language will be selected.

AUDIO OUTPUT (See p. 50.)

You can set the audio output that comes from the

digital audio output terminal.

STILL MODE (See p. 51.)

To select “FIELD” (Field still) or “FRAME” (Frame

still) to prevent jitter or make small text or fine

patterns clearly visible in a still picture. When

“AUTO” is set “FIELD” or “FRAME” is selected

automatically.

TV MODE (See p. 51.)

To select whether the video material for a wide-

screen will be played back in the Pan & Scan style,

Letterbox style or 16 : 9 style.

Press

to select

“DISC LANGUAGES,”

and

press

SET

to display screen.

Press

ACTION

to display MENU.

Press

to select an item, and

press

SET

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DIDISC LANGUAGESSC LANGUAGES

AUDIO OUTPUT

STI LL MODE :

AUTO

TV MODE : Le tt erbox 4:3

PARENTAL

LOCK

LEVEL 8

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DIDISC LANGUAGESSC LANGUAGES

AUDIO OUTPUT

STI LL MODE :

AUTO

TV MODE : Let terbox 4:3

PARENTAL

LOCK

LEVEL 8

Press

to select an item, and

press

SET

repeatedly

for desired language.

(Please refer right.)

DISC LANGUAGES

SELECT :

SET : SET

END : ACTION

AUAUDIDIO : : EnglishEnglish

SUBTI TLE : AUTO

MENUS : English

Press

ACTION

to redisplay DVD menu

and go to step 2 to setup another item.

Or, press

ACTION

twice to exit.

If the selected language is not offered,

the original disc language is selected.

SET

ACTION

SELECT

NUMBER

keys

CLEAR

Ready Checklist

DECK is in DVD mode, press DVD.

DVD

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

• Make settings according to amplifier

connected to optical audio output as shown

in above table.

• When a dts decoder is not connected, to

enjoy dts DVD, please select audio output

other than dts at the dts DVD menu screen.

Otherwise, there will be no sound.

*1 Audio Output 2 from DECK is converted to

48 kHz/16 bit in addition to audio from

digital audio output.

To enjoy high quality sound at 48 kHz/20

bit /24 bit or 96 kHz, connect the amplifier

or decoder directly to the Audio Output 2

connectors, not to the Digital Audio Output

connector. [Select “OFF” at the “LPCM

(DVD)”.]

*2 When connecting an amplifier (with an

optical digital input connector) which does

not contain the Dolby Digital or dts

decoder, be sure to select “OFF”.

If “Bitstream” is selected, starting DVD play

may cause such a high level of noise as to

be harmful to your ears and damage the

speakers.

*3 When a dts decoder is connected, please

select “Bitstream” in “dts”. If “OFF” is

selected, there will be no sound.

Audio Output

Select the digital output to be output from the optical

digital audio output connector of DECK.

■■

■ “LPCM (DVD)” selections

OFF: Linear PCM of less than 48 kHz/16 bit is

output. When playing DVDs recorded in

linear PCM of over 48 kHz/20 bit or 96 kHz,

no digital audio is output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM

of 48 kHz/20 bit/24 bit or 96 kHz, digital

audio converted to 48 kHz/16 bit is output.

(Digital output of PCM audio is restricted to

48 kHz/16 bit or below for copyright

protection.)

■■

■ “Dolby Digital” selections

Bitstream: Dolby Digital bitstream (1ch-5.1ch) is

output. (Factory preset)

OFF: No output.

■■

■ “dts” selections

Bitstream: dts bitstream is output. (Factory preset)

OFF: No output.

■■

■

“DRC (Dynamic Range Compression)” selections

OFF: Normal audio range is selected. (Factory

preset)

ON: For dynamic sound even at low volume, this

is useful for late-night listening. [Dolby Digital

DVDs only].

■■

■ “SURROUND” selections

Surround Sound creates the effect of sound coming

from non-existent rear speakers even when only

connected to a 2-channel stereo system.

OFF: No Surround Sound effect. (Factory preset)

ON: Surround Sound effect.

Press

to select an item,

and

press

SET

repeatedly for

output. (See below.)

Press

to select

“AUDIO OUTPUT,”

and

press

SET

to display screen.

Settings for DVD Operation (continued)

• Turn off other surround effects when using

this surround effect.

• For optimum effect, the distance between

DECK and the listener should be about 3 or 4

times the distance between the right and left

front speakers.

Notes

Recommended setting

LPCM

(DVD)

OFF

PCM*

Dolby

Digital

OFF

OFF*

Bitstream

dts

OFF

OFF*

OFF

Bitstream

No amplifier is connected

AV amplifier (with digital

audio input connector)

without Dolby Digital/dts

decoder

AV amplifier including

Dolby Digital decoder

AV amplifier including

Dolby Digital/dts decoder

Type of amplifier

to be connected

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STILL MODE : F

LED

TV MODE : Letterbox 4:3

PARENTAL

LOCK

LEVEL 8

AUDIO OUTPUT

SELECT :

SET : SET

END : ACTION

LPCM(DVD)

: OFF

Dolby Digital : Bitstream

dt s : OFF

DRC : OFF

SURROUND : OFF

Press

ACTION

to redisplay DVD menu

and go to step 2 to setup another item.

Or, press

ACTION

twice to exit.

Press

ACTION

to display MENU.

Ready Checklist

DECK is in DVD mode, press DVD.

Still Mode

Press

to select “STILL MODE,”

and

press

SET

repeatedly

for mode. (See below.)

AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is

automatically selected during the still mode.

(Factory preset)

FIELD: “FIELD” (Field still) is always selected.

This setting will reduce jitter when compared

with “AUTO” on some discs.

FRAME:“FRAME” (Frame still) is always selected.

Some texts and fine patterns will be seen clearly

when compared with “AUTO” on some discs.

TV Mode

Press

to select “TV MODE,”

and press

SET

repeatedly for mode.

(See below.)

Pan & Scan 4 : 3 (Factory preset) :

Wide-screen video data is played in Pan & Scan

style (left and right of screen is trimmed.)

• Video data not formatted in Pan & Scan will play

in letterbox style.

Letterbox 4 : 3 :

Wide-screen video data is played in Letterbox

style (top and bottom of screen has black margin).

16 : 9 :

Set “16: 9” when using Wide-screen TV.

Set the screen display style for wide-screen video

material playback.

• Pan & Scan (Factory preset)

• Letterbox

Set to reduce jitter in a displayed still picture or a motion

picture.

Press ACTION

to exit this mode.

Press

ACTION

to exit this mode.

Example

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STI

LL MODE : F

ELD

TV MODE : Letterbox 4:3

PARENTAL

LOCK

LEVEL 8

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STILL MODE : F

LED

TV MODE

: Letterbox 4:3

Letterbox 4:3

PARENTAL

LOCK

LEVEL 8

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

SET

ACTION

SELECT

Press

ACTION

to display MENU.

Press

ACTION

to display MENU.

DVD

Operation

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or

“MENUS” (see p. 49).

Code Language

7079 Faroese

7082 French

7089 Frisian

7165 Irish

7168 Scots Gaelic

7176 Galician

7178 Guarani

7185 Gujarati

7265 Hausa

7273 Hindi

7282 Croatian

7285 Hungarian

7289 Armenian

7365 Interlingua

7378 Indonesian

7383 Icelandic

7384 Italian

7387 Hebrew

7465 Japanese

7473 Yiddish

7487 Javanese

7565 Georgian

7575 Kazakh

7576 Greenlandic

7577 Cambodian

7578 Kannada

7579 Korean

7583 Kashmiri

7585 Kurdish

7589 Kirghiz

7665 Latin

Code Language

7678 Lingala

7679 Laothian

7684 Lithuanian

7686

Latvian, Lettish

7771 Malagasy

7773 Maori

7775 Macedonian

7776 Malayalam

7778 Mongolian

7779 Moldavian

7782 Marathi

7783 Malay

7784 Maltese

7789 Burmese

7865 Nauru

7869 Nepali

7876 Dutch

7879 Norwegian

7982 Oriya

8065 Panjabi

8076 Polish

8083

Pashto, Pushto

8084 Portuguese

8185 Quechua

8277

Rhaeto-Romance

8279 Romanian

8285 Russian

8365 Sanskrit

8368 Sindhi

8372

Serbo-Croatian

8373 Singhalese

Code Language

8375 Slovak

8376 Slovenian

8377 Samoan

8378 Shona

8379 Somali

8381 Albanian

8382 Serbian

8385 Sundanese

8386 Swedish

8387 Swahili

8465 Tamil

8469 Telugu

8471 Tajik

8472 Thai

8473 Tigrinya

8475 Turkmen

8476 Tagalog

8479 Tonga

8482 Turkish

8484 Tatar

8487 Twi

8575 Ukrainian

8582 Urdu

8590 Uzbek

8673 Vietnamese

8679 Volapük

8779 Wolof

8872 Xhosa

8979 Yoruba

9072 Chinese

9085 Zulu

Code Language

6565 Afar

6566 Abkhazian

6570 Afrikaans

6577 Ameharic

6582 Arabic

6583 Assamese

6588 Aymara

6590 Azerbaijani

6665 Bashkir

6669 Byelorussian

6671 Bulgarian

6672 Bihari

6678

Bengali; Bangla

6679 Tibetan

6682 Breton

6765 Catalan

6779 Corsican

6783 Czech

6789 Welsh

6865 Danish

6869 German

6890 Bhutani

6976 Greek

6978 English

6979 Esperanto

6983 Spanish

6984 Estonian

6985 Basque

7065 Persian

7073 Finnish

7074 Fiji

These displays will alert you to a missed operation or provide further instructions.

Warning and Instruction Displays

For Your

Information

PLEASE SET CLOCK BY

PRESSING ACTION KEY

CHECK CASSETTE

RECORD TAB

NO CASSETTE

VIDEO HEADS MAY NEED

CLEANING PLEASE INSERT

HEAD CLEANING CASSETTE

OR REFER TO MANUAL

END : PLAY

VCR LOCK ACTIVATED

Page

CautionOSD

If you attempt to set or review a Timer

Recording and the Clock is not set...

If DECK is not in Stop mode or a cassette

with record tab is not inserted 2 minutes

before a Timer Recording is about to

begin...

If you press REC on the remote control or

DECK, and a cassette is inserted with no

record tab...

If you press PLAY, FF, REW, or REC on

the remote control or DECK without a

cassette inserted...

If you press STOP or POWER

during a Timer Recording...

(visible in VCR mode only)

If head cleaning becomes necessary

while playing back a tape...

If you press a function button other than

STOP/EJECT or POWER while DECK is

in VCR Lock mode...

If you press an invalid key on the remote

while in CABLE/DSS mode...

If you press an invalid key on the remote

while in TV mode...

REMOTE CONTROL IS SET

TO TV MODE

USE VCR : VCR KEY

USE DVD : DVD KEY

REMOTE CONTROL IS SET

TO CABLE/DSS MODE

USE VCR : VCR KEY

USE DVD : DVD KEY

PLEASE PREPARE FOR TIMER

REC

PLEASE CHECK THE DISC,

AND FOR STAINS OR

SCRATCHES ON DISC

If you press PLAY, or DECK reads

data from a stained or scratched disc

in DVD mode. Also, if the type of disc

is other than DVD, Video CD or CD...

IT IS PROHIBITED TO COPY

DVD/VIDEO CD/CD TO VHS

If you press REC in DVD mode...

TO CANCEL TIMER REC

HOLD DOWN STOP KEY

FOR APPROX 3 SEC

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Before Requesting Service

Power

No power…

Power turns itself off...

Recording & Playback

TV program cannot be recorded...

Timer recording cannot be

performed…

There is no playback picture, or the

playback picture is noisy or contains

streaks...

Special effects playback, picture may

contain some vertical jitter when using

a TV with an Automatic Vertical Hold

Control...

DECK cannot be controlled...

Check the following points if you are having trouble with your DECK.

Correction

• Completely insert Power Plug into an AC outlet.

• Set POWER button to on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min.

in DVD mode with no operation, or if there is no

broadcast signal in TV or Playback mode.

Turn the power back on. (pp. 23, 37)

Correction

• Check connections between DECK, external

antenna, and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is

correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and

tuned to channel to be recorded.

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued

if a power interruption occurs before or during a

Timer Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output

channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

• Adjust TRACKING control in either direction. (p. 6)

• Try Head Cleaning. (p. 6)

• Set TV’s Vertical Hold Control to MANUAL, then

adjust.

• Make sure DECK power is on.

• Check Remote batteries.

• Make sure VCR LOCK is set to off. (p. 37)

• Make sure Remote is in proper mode.(p. 28)

• Make sure Timer Recording is not in progress.

Remote Control

DECK cannot be remote controlled...

PROG buttons do not respond...

Correction

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p. 9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent

or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT

Video Output and S-VIDEO OUT. Set TV to either RF

IN or VIDEO IN. (p. 10)

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

Check the following points if you are having trouble with your DECK.

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Video cassette ejects when

a recording is started or the power is

turned off for timer recording...

In Stop mode, the motor (CYLINDER)

continues to rotate...

The disc cannot be removed..

Correction

• Make sure TV is set to output of DECK.

• Check connections between DECK,

external antenna, and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• Insert the cassette with window side up; record

tab facing you.

• Make sure cassette record tab is intact. (p. 6)

• To enable Quick play mechanism, the cylinder will

rotate for about 3 minutes. This reduces response

time from Stop to Play mode.

• First, unplug DECK. Then, prepare a rigid wire

(e.g. an extended paper clip) and, applying

moderate force, insert it straight into the hole at the

base of the tray. The tray will eject a little. Now, pull

the tray all the way out and remove the disc. (p. 9)

DVD/ Video CD/ CD

Play fails to start even when PLAY is

pressed...

Play starts but then stops immediately...

Picture is distorted during rapid

advance or rapid reverse...

No Forward/Reverse Scene Search

play...

Play does not start even when title is

selected...

Audio soundtrack and/or subtitle

language is not the one selected at

the initial settings...

No subtitles...

Alternative audio soundtrack

(or subtitle) language cannot be

selected...

Angle cannot be changed...

Correction

• This DECK cannot play discs other than DVDs,

Video CDs and CDs.

• The disc may be dirty and require cleaning.

• Be sure disc is installed with label side up.

• The picture will be somewhat distorted at times:

this is normal.

• Some discs may have sections which prohibit

Forward/Reverse Scene Search. (p. 23)

• Confirm the “DVD LOCK” setting. (p. 48)

• If the audio soundtrack and/or subtitle language

selected at DVD initial settings does not exist

on the disc, it will not be accessible.

• Subtitles appear only when available on disc.

• “OFF” is selected at the changing subtitle

language. Select “ON” at the “Subtitle Languages”

section (p. 40) to display the subtitles.

• Alternative language cannot be selected with discs

which do not contain more than one language.

• For some discs, alternative language cannot be

selected with the AUDIO or SUB TITLE button.

Try selecting it from the DVD MENU if available.

• This function is dependent on software availability.

Even if disc has multiple angles, they may be

recorded for specific scenes only (ANGLE

indicator on DECK lights up). (p. 41)

If you cannot resolve the problem, please call the Customer Call Center for product

assistance at 1-800-211-PANA (7262).

To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).

or send e-mail to : [email protected]

For Your

Information

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Servicenter List

Factory Servicenters Locations

Web Site: http://www.panasonic.com

You can purchase parts, accessories or locate your

nearest servicenter by visiting our Web Site.

For Product Information, Operating Assistance, Literature Request, Dealer

Locations, and all Customer Service inquiries please contact:

1-800-211-PANA (7262), Monday-Friday 9am-9pm Saturday-Sunday 9am-7pm,

EST. or send e-mail to : [email protected]

Service in Puerto Rico

Matsushita Electric of Puerto rico, Inc. Panasonic Sales Company/ Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

Customer Orders Only 800-332-5368 (Customer Orders Only)

Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032

(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)

(Visa, MasterCard, Discover Card, American Express, Check)

Accessory Purchases:

As of Sep. 2001

CALIFORNIA

6550 Katella Avenue

Cypress, CA 90630

800 Dubuque Avenue

S. San Francisco,

CA 94080

3878 Ruffin Road

Suite A

San Diego, CA 92123

FLORIDA

3700 North 29th Avenue

Suite 102

Hollywood, FL 33020

GEORGIA

8655 Roswell Road

Suite 100

Atlanta, GA 30350

ILLINOIS

1709 North Randall Road

Elgin, IL 60123

MASSACHUSETTS

60 Glacier Drive

Suite G

Westwood, MA 02090

MINNESOTA

7850-12th Avenue South

Airport Business Center

Bloomington, MN 55425

OHIO

2236 Waycross Road

Civic Center Plaza

Forest Park, OH 45240

PENNSYLVANIA

2221 Cabot Blvd. West

Suite B

Langhorne, PA 19047

TEXAS

13615 Welch Road

Suite 101

Farmers Branch,

TX 75244

WASHINGTON

20425-84th Avenue

South

Kent, WA 98032

HAWAII

99-859 Iwaiwa Street

Aiea, Hawaii 96701

Phone (808)488-1996

Fax (808)486-4369

Limited Warranty

Panasonic Consumer Electronics Company,

Division of Matsushita Electric Corporation

of America, One Panasonic Way

Secaucus, New Jersey 07094

Panasonic Sales Company,

Division of Matsushita Electric of Puerto Rico, Inc.

AVE. 65 de Infantería, Km. 9.5 San Gabriel

Industrial Park, Carolina, Puerto Rico 00985

PANASONIC/QUASAR Video Products

Limited Warranty

Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the Warrantor”)

will repair or replace this product with new or refurbished parts or equivalent product, free of charge, in the USA or

Puerto Rico, in the event of a defect in materials or workmanship as follows (all time periods commence from the date

of the original purchase):

PRODUCT

CAMCORDER

DVD/VCR DECK

DIGITAL STILL

CAMERA

A/V MIXER

TV/VCR, TV/DVD

TV/DVD/VCR

COMBINATION

TV/HDR

COMBINATION

LABOR

NINETY (90) DAYS

CRT - NINETY (90) DAYS

NINETY (90) DAYS

CRT - NINETY (90) DAYS

PARTS

ONE (1) YEAR, EXCEPT

CCD IMAGE SENSOR

SIX (6) MONTHS

ONE (1) YEAR

ONE (1) YEAR, EXCEPT

CCD IMAGE SENSOR

SIX (6) MONTHS

ONE (1) YEAR

ONE (1) YEAR,

EXCEPT CRT

CRT

TWO (2) YEARS

ONE (1) YEAR,

EXCEPT CRT

CRT

TWO (2) YEARS

CONTACT NUMBER

1-800-211-PANA(7262)

1-800-272-7033

1-800-211-PANA(7262)

1-888-843-9788

SERVICE

Carry-In or Mail-In

Carry-In: 21” CRT

and Smaller

In-Home or Carry-In:

22” CRT and Larger

In-Home or Carry-In

Batteries (if included) - New rechargeable batteries in exchange for defective rechargeable batteries for ten (10)

days. Non-rechargeable batteries are not warranted.

Tape (if included) - New video cassette tape in exchange for a defective video cassette tape for five (5) days.

Memory cards (if included) - Exchange defective item for new one for ninety (90) days.

In-home, carry-in or mail-in service, as applicable, in the USA can be obtained during the warranty period by

contacting a Panasonic Services Company (PASC) Factory Servicenter listed in the Servicenter Directory. Or call toll

free contact number listed above, to locate an authorized PASC Servicenter. Carry-in or mail-in service in Puerto Rico

can be obtained during the warranty period by calling the Panasonic Sales Company telephone number listed in the

Servicenter Directory.

This warranty is extended only to the original purchaser. A purchase receipt or other proof of the date of the original

purchase is requires before warranty service is rendered.

This warranty only covers failures due to defects in materials and workmanship, which occur during normal use and

does not cover normal maintenance, including, but not limited to, video and audio head cleaning. The warranty does

not cover damage which occurs in shipment, or failures which are caused by products not supplied by the warrantor,

or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification,

faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer

controls, improper operation, power line surge, improper voltage supply, lightning damage, commercial use such as

hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a PASC

Factory Servicenter or a PASC authorized Servicenter, or damage that is attributable to acts of God.

LIMITS AND EXCLUSIONS

There are no express warranties except as listed above.

THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

(INCLUDING, WITHOUT LIMITATION, DAMAGE TO RECORDING MEDIA) RESULTING FROM THE USE OF

THIS PRODUCTS, OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED

WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR

PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations

on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.

This warranty gives you specific legal rights and you may also have other rights, which vary, from state to

state. If a problem with this product develops during or after the warranty period, you may contact your

dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the Consumer Affairs

Department at the Panasonic Consumer Electronics Company address above.

SERVICE CALLS WHICH DO NOT INVOLVE DEFECTIVE MATERIALS OR WORKMANSHIP

AS DETERMINED BY THE WARRANTOR, IN ITS SOLE DISCRETION, ARE NOT COVERED.

COSTS OF SUCH SERVICE CALLS ARE THE RESPONSIBILITY OF THE PURCHASER.

warvid 02/ 12/ 2001

For Your

Information

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Spanish Quick Use Guide/ Guía para rápida consulta

Para ajustar el idioma, canal yPara ajustar el idioma, canal y

Conexiones/Configuracion Inicial (READY TO PLAY)

Favor realice la conexion de antena o cable antes de conectar el cordon de AC a la

toma de pared.

Conectando el cordon de AC de la DECK en toma de pared iniciara automaticamente la busqueda

de canales y colocacion de tiempo.

Conectando

Conecte Ant/Cable a la entrada de antena

de la DECK (DECK In).

Conecte la salida de la DECK (DECK Out) a

la entrada de antena de la TV (TV In) con el

cable-accesorio RF incluido.

Para Ant/Cable

➛➛

➛ DECK

➛➛

➛ TV

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable

➛➛

➛ DECK

➛➛

➛ TV

Conecte la salida del convertidor de cable

a la ”DECK In” con el RF cable accesorio

incluido.

Conecte “DECK Out” a la “TV In” con el

cable-accesorio incluido.

Realizando configuracion inicial

Presione el boton DECK del control remoto

para dicha modalidad. Encienda la TV y

cambie a canal 3.

Conecte cordon de AC de la DECK a la

toma de pared. La DECK se activara e

iniciara busqueda de canales y colocacion

de tiempo.

• Si la pantalla abajo no aparece cheque la

conexion DECK-TV y si la TV fue cambiada a

el canal 3,trate cambiando a el canal 4.

• Para cambios a el canal de salida de la DECK

favor hacer referencia a “VCR’s Output

Channel” (p. 19).

Conectando cordon de AC a la toma de pared.

DECK

VHF/UHF

Estuche convertidor

de TV por cable

Televisor

Terminal

IN FROM ANT.

Entrada (IN) desde

ANT./CABLE

Terminal

OUT TO TV

Terminal IN FROM ANT.

Televisor

DECK

VHF/UHF

Terminal

OUT TO TV

Entrada (IN) desde

ANT./CABLE

Si usa convertidor de cable solo enciendala y

seleccione el canal PBS en su horario de uso u

horario de zona. Si utiliza receptor DSS este debe

estar apagado.

PRECAUCION

Si se sobre ajusta “NUT TYPE” el cable coaxial

RF podria dañar las terminales de conexion.

Ajusta ligeramente utiliza solo los dedos.

Selecciones se realizaron automaticamente

cuando la configuracion termino, esta

pantalla aparece.

Si “Auto clock set is incomplete” aparece,

coloque manualmente el tiempo, vealo abajo.

JAC

ON AUTOMATICA

DEL RELOJ ES I

NCOMPLETO

POR FAVOR FIJE

RELOJ

CON LA TECLA ACTION

DOM 2

20P

HORA VERAN I EGA : ACT

CANAL FIJADO

: CA

JAC

ON AUTOMAT

COMPLETO

Realizando configuracion inicial

Si la colocacion de tiempo fue incompleta.

Presione la tecla ACTION en el control remoto

para visualizar la pantalla del menú RELOJ.

Presione para seleccionar el mes y SET

para ajustar. De la misma forma, seleccione y

ajuste la fecha, año, hora y DST (Hora de

Verano).

Presione dos veces la tecla ACTION para

poner el RELOJ en marcha y salir.

VERANO

ACT

ELEGIR

FIJAR

SET

SALIR

ACT

FIJAR RELOJ

----

ELEGIR MES

VERANO

ACT

FIJAR RELOJ

29 /

2002

DOM

12:00PM

FIJACION ES COMPLETO

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]

FIJACION

AUTOMATICA

DEL

RELOJ

PROCESO

CANCELAR : STOP

AUTOPROGRAMACION

EN PROCESO

CANCELAR : STOP

Al inicio, el idioma de

la pantalla está fijado

a inglés.

Para cambiar el

idioma consulte la

página 18.

Operaciones básicas para la reproducción

Grabación de un toque (grabar en

marcha),

Presione REC repetidamente para ajustar la

hora de grabación (30 min - 4 horas).

• La videograbadora termina la grabación

a una hora programada.

Grabación normal

0:30 1:00

1:302:003:004:00

Programación fácil para la

grabación con temporizador

Presione PROG

para visualizar PROGRAM.

1) Para ajustar la FECHA de

grabación, presione

para seleccionar:

1-31 = una vez, o

DIARIO = a la misma hora

de lunes a viernes, o

SEMANA = a la misma

hora cada semana y

presione SET para ajustar.

2) Para ajustar los ítems que quedan,

presione para seleccionar y presione

SET para ajustar los tiempos de INICIO/

PARADA, CANAL, o entrada de LÍNEA (pág.

35), y velocidad del cassette (SP, LP, SLP).

Presione PROG para finalizar PROGRAM.

Presione

para seleccionar un número

que no está usando para

ingresar mas programas y

presione SET

para ajustar.

Luego repita el paso 2.

Presione nuevamente

PROG para salir.

Fecha de hoy

Orden para elegir

Ejemplo

FECHA

PARADA

SAB

--:--

HOY

ELEGIR

FIJAR

SET

TERMINAR

PROG

SLP

ELEGIR FECHA DE I

DIARIO

68 9

/ Orden para elegir

SEMANAL

(

SAB

)

SEMANAL

(

LUN

)

SEMANAL

(

DOM

)

ELAR

DLT

ELEGIR 1- 8 :

ENTRAR

: SET

SAL

PROG

PARADA

VEL

7 7

2 : 002 : 00

3 3

2020

02 SLP

Guía para rápida

consulta

Operaciones básicas para la reproducción

Inserte un cassette,

• La alimentación del DECK se activa.

En la Pantalla de Visualización Multi

Función se ilumina “VCR”.

Presione PLAY para reproducir el cassette.

• Si el cassette no tiene lengüeta de

prevención de grabación (página 6), se

inicia la reproducción automáticamente.

Detalles especiales durante la grabación

Presione FF/SLOW+ o REW/SLOW- para

búsqueda de escenas hacia delante/ hacia

atrás. Presione PLAY para liberar. Luego de

que la búsqueda se ha iniciado, cada vez

que presione FF/SLOW+ o REW/SLOW-

se cambia la velocidad como sigue:

[SLP] aprox. 21X

↔↔

↔ aprox. 9X

[LP] aprox. 9X

↔↔

↔ aprox. 7X

[SP] aprox. 7X

↔↔

↔ aprox. 3X

Si la imágen se interrumpe con la velocidad de

21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x.

Presione PAUSE/STILL para imagen Fija

(Congelada).

Presione PLAY para liberar.

Presione PAUSE/STILL en el modo de

imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar.

Presione FF/SLOW+ o REW/SLOW- en el

modo de imagen fija para imágenes cuadro

a cuadro. Presione PLAY para liberar.

Presione STOP para detener el cassette.

Presione REW/SLOW- o FF/SLOW+ en el

modo de parada para rebobinado/avance

rápido del cassette.

Presione EJECT en el control remoto,

o STOP/EJECT en el DECK para expulsar

el cassette.

Operaciones básicas para la grabación

Inserte el cassette con lengüeta de

protección de grabación (pág. 6).

Presione CH / , o las teclas de números

para seleccionar el canal.

Presione SPEED para seleccionar la

velocidad de grabación (pág.6)

Presione REC para comenzar a grabar.

• Para eliminar escenas indeseadas, presione

PAUSE/STILL para pausar, y al presionar

nuevamente se reanuda la grabación.

• No podrá ver otro canal durante la

grabación.

Presione STOP para detener la grabación.

• SP = Reproducción estándar,

• LP = Larga duración,

• SLP = Superlarga duración.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Spanish Quick Use Guide/ Guía para rápida consulta

Presione

POWER

en el control remoto o el aparato.

Presione

DVD

para seleccionar el modo DVD.

1) Presione

OPEN/CLOSE

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus superficies,

póngalo con el lado donde esté impreso el título

hacia arriba, alinéelo con las guías y póngalo en su

posición apropiada.

Disco de 3”(8 cm) Disco de 5” (12 cm)

Presione

PLAY

para iniciar la reproducción.

La bandeja del disco se cierra automáticamente.

• Si está usando un DVD interactivo (Interactive DVD)

o un Vídeo CD con contol de reproducción

(playback control) y aparece un menú de títulos

(TITLE MENU) en la pantalla, siga al paso 5.

Presione o las teclas numéricas para

seleccionar el artículo deseado.

Presione

SET

para la reproducción.

Si usa las teclas numéricas, la reproducción

comienza automáticamente.

Presione

STOP

para parar la reproducción.

Presione

OPEN/CLOSE

para expulsar el disco.

■ Para buscar una escena particular

Búsqueda hacia adelante

Presione

FF/SLOW+

en el modo de reproducción.

Búsqueda hacia atrás

Presione

REW/SLOW-

en el modo de reproducción.

(Para liberar, presione

PLAY

)

■ Para saltar un capítulo o una pista

Salto hacia adelante

Presione

SKIP

l en el modo de reproducción.

Un capítulo (DVD) o una pista (Vídeo CD/CD) se salta cada ves que se oprime la tecla.

Salto hacia atrás

Presione l

SKIP

en el modo de reproducción.

■■

■ Para ver una imagen fija

Presione

PAUSE/STILL

durante la reproducción.

(Para liberar, presione

PLAY

)

■ Para ver imágenes cuadro a cuadro

(DVD/Vídeo CD)

Presione

PAUSE/STILL

en el modo de imagen fija.

La imagen avanza un cuadro cada vez que presiona la tecla.

(Para volver a la reproducción normal, presione

PLAY

■ Para ver en cámara lenta (DVD/Vídeo CD)

Presione

FF/SLOW+

REW/SLOW-

en el modo de imagen fija.

(Para liberar, presione

PLAY

)

Operaciones básicas del DVD

OPEN/

SET

STOP

POWER

REW/

SLOW-

NUMBER

keys

PLAY

DVD

PAUSE/

STILL

SKIP

SELECT

FF/

SLOW+

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]

Cuando se presiona DISPLAY, la visualización en pantalla

muestra la información del disco (título / capítulo / número de

lista, tiempo transcurrido de reproducción, audio / idioma del

subtítulo, y ángulo) e información (repetir la reproducción,

modo reproducción, Karaoke vocal encendido / apagado, etc.).

Funcionnamiento del DVD utilizando

visualizaciones en pantalla

Presione

DISPLAY

en el modo reproducción o parada

para visualizar Visualizaciones en pantalla.

• Cada vez que se presione

DISPLAY

, la visualización

en pantalla cambia como se muestra a continuación.

Presione para seleccionar el ajuste deseado.

Presione

SET

para ajustar.

Para volver a la pantalla normal,

Presione repetidamente

CLEAR

DISPLAY

Presione (o ) para seleccionar el ítem deseado.

Presione

SET

para ajustar.

ELEGIR :

FIJAR : SET SIGUIENTE: DISPLAY

TI TULO : 12 DVD

CAPIPITULOTULO

: 1111 0:12:34

ELEGIR :

FIJAR : SET SIGUIENTE: DISPLAY

TI TULO : 12 DVD

TULO

: 24

0:12:34

STA

: 12

VIDEO CD

PBC : INACTIVO 0: 12: 34

FIJAR : SET SIGUIENTE: DISPLAY

STA

: 17

VIDEO CD

PBC : INACTIVO 0: 12: 34

FIJAR : SET SIGUIENTE: DISPLAY

Información seleccionada del disco

Información seleccionada de del DECK

Pantalla normal

SELECT

DISPLAY

CLEAR

SET

Guía para rápida

consulta

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Cambio del idioma de subtítulos

[DVD solamente]

EI idioma de los subtítulos seleccionado al hacer las

fijaciones iniciales se puede cambiar por otro idioma

diferente, si éste se encuentra disponible.

Presione

SUBTITLE

durante la reproducción.

Cuando no haya

subtítulos grabados, “-”

se visualizará en lugar

del número de idioma.

Presione para

seleccionar el idioma

deseado.

Presione (o ) para

ajustar.

Presione para

seleccionar “ACTIVO” o

“INACTIVO.”

Cambio del idioma de la pista de

sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al hacer

las fijaciones iniciales se puede cambiar por otro

idioma diferente, si éste se encuentra disponible.

Presione

AUDIO

durante

la reproducción para

visualizar la pantalla

AUDIO.

Presione para

seleccionar idioma.

Selección de IDIOMAS DEL

DISCO [DVD solamente]

Presione para seleccionar el artículo deseado.

Presione

SET

IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco pueden ser

ajustados, Si el idioma ajustado no es ofrecido en el

disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio procedente del

terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO” o “CUADRO fijo” para

prevenir inestabilidad o para permitir ver textos

pequeños o patrones finos claramente en el modo

de imagen fija.

PREFERENCIA

Para seleccionar si el material del vídeo para

pantalla ancha será vuelto a reproducir en el estilo

Pan&Scan, en el estilo Letterbox o en el estilo 16 :

9 en la pantalla.

Volver a visualizar el menú de DVD para

continuar el ajuste.

Presione

ACTION

y pase al paso 3 para ajustar

otro ajuste o, para salir, presione

ACTION

tres

veces.

Presione DVD para seleccionar el mode DVD.

Presione ACTION en el modo de parada para

visualizar MENU.

Presione para seleccionar el artículo deseado.

Presione

SET

Seleccione “AUDIO”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa :

Originl : Se seleccionará el idioma

original de cada disco.

OTRO **** : Se puede seleccionar el otro

idioma.

Seleccione “SUBTITULO”

(Fijación de fábrica)

AUTO : Se seleccionará el mismo que fue

seleccionado en la preparación

de “AUDIO”.

• Si el idioma seleccionado en la

preparación de “AUDIO” se utiliza

durante la reproducción, los subtítulos

no aparecerán.

• Si se utiliza otro idioma durante la

reproducción, los subtítulos aparecerán

en el idioma seleccionado en la

preparación de “AUDIO”

Inglés / Español / Francés / Japonesa :

OTRO **** : Se puede seleccionar el otro

idioma.

Seleccione “MENU”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa :

OTRO **** : Se puede seleccionar el otro

idioma.

Fijaciones iniciales

Spanish Quick Use Guide/ Guía para rápida consulta

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]

Algunos discos con películas, por ejemplo,

vienen con dos o más títulos. Si el disco tiene

un menú de títulos grabados, el botón TITLE

podrá utilizarse para seleccionar el título de la

película.

Presione

TITLE

durante la reproducción.

Ahora se visualiza una lista de los títulos

del disco.

Utilización de un menú de títulos

[DVD solamente]

TLE MENU

Cas

Love

Dogs

Presione o

las teclas de

números para

seleccionar el título

deseado.

Presione

SET

Algunos discos DVD tienen estructuras únicas de

menús llamadas menús DVD. Por ejemplo, los DVDs

programados con un contenido complejo

proporcionan menús guía, y los grabados con varios

idiomas proporcionan menús para audio e idiomas de

subtítulos. Aunque los contenidos de los menús DVD

y la operación cambian de disco a disco, a

continuación se explica la operación básica cuando

se utiliza esta característica.

Presione

durante la reproducción.

El menú de DVD introducido en el disco se

visualiza ahora.

Dogs

of the world

Visión desde otro ángulo

[DVD solamente]

Algunos discos DVD tienen escenas que han

sido filmadas simultáneamente desde un

número de ángulos diferentes. Con estos

discos, la misma escena podrá verse desde

cada uno de estos ángulos diferentes

utilizando el botón ANGLE.

Presione

ANGLE

durante la

reproducción para

visualizar la

pantalla de ángulo.

ANGULO

: 1

ELEGIR : FIJAR :SET

ANGULO

: 2

ELEGIR : FIJAR :SET

Presione

AUDIO

durante la reproducción

para visualizar la pantalla AUDIO.

Selección de vocal para los discos de

Karaoke [DVD/Video CD]

Presione (o )

para seleccionar el ajuste

deseado.

Presione (o ) para

ajustar. (DVD solamente)

Presione o las

teclas de números

para seleccionar el ítem

deseado.

Presione

SET

Ampliación de la imagen [DVD solamente]

Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar

la relación de zoom usando el botón ZOOM.

Presione

ZOOM

repetidamente para cambiar el

tamaño de la imagen como se indica a continuación:

Presione para

seleccionar el

ángulo deseado.

2da2da

3da3da

■ Use los botones , , y para desplazar la posición hacia arriba, hacia abajo, hacia la

izquierda o hacia la derecha.

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1

V2 VOCAL V1 VOCAL V2 VOCAL OFF

• Video CD LR L R

Utilización de un menú de DVD

[DVD solamente]

DVD MENU

3 . ANGLE

1 . SUBT

TLE

2 . AUD

Guía para rápida

consulta

Panasonic MP3 Player PV-D4762 Manual de usuario

Marca: Panasonic

Modelo: MP3 Player PV-D4762

Categoría: Reproductores de DVD

Tipo: Manual de usuario

Este manual también es adecuado para

PV-D4762

Descargar PDF

informe

en otros idiomas

English: Panasonic MP3 Player PV-D4762 User manual

Panasonic MP3 Player PV-D4762 Manual de usuario

Este manual también es adecuado para

Panasonic MP3 Player PV-D4762 Manual de usuario

en otros idiomas

Artículos relacionados

Otros documentos