Panasonic PVD4763S Instrucciones de operación

Marca: Panasonic

Modelo: PVD4763S

Categoría: Reproductores de DVD

Tipo: Instrucciones de operación

PV-D4763S

DVD/VCR DECK

Operating Instructions

LSQT0676A

Model No.

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Initial Setup

(Connection)

Basic

Operation

VCR

Operation

For Your

Information

DVD

Operation

Connections and Initial Setup Procedures are on pages 12 to 17.

Please read these instructions carefully before attempting to connect, operate or adjust this

product. Please save this manual.

Spanish Quick Use Guide is included.

(Guía para rápida consulta en español está incluida.)

As an ENERGY STAR Partner, Matsushita Electric Corporation

of America has determined that this product or product model

meets the ENERGY STAR guidelines for energy efficiency.

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:471

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the

unit or in this manual. If necessary, have your

Electric Utility Service Company or Video Products

Dealer verify the power source in your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either

a polarized power cord plug (one blade is wider

than the other), or a three-wire grounding type plug.

POLARIZED PLUG CAUTION:

This plug will only fit into an outlet one way. If you cannot

fully insert the plug, try reversing it. If it still will not fit,

have an electrician install the proper wall outlet. Do not

defeat the safety feature by tampering with the plug.

GROUNDING PLUG CAUTION:

This plug will only fit into a three-hole grounding

outlet. If necessary, have an electrician install the

proper outlet. Do not defeat the safety feature by

tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they

are not likely to have anything rest on them, roll

over them, or be in the way of walking traffic.

If an extension cord is used, make sure it also

has either a polarized or grounded plug and that

the cords can be securely connected.

Frayed cords, damaged plugs, and damaged or

cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire

hazards and should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat

generated during operation. If they are blocked,

heat build-up inside the unit can cause failures that

may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in

use, or operate the unit when placed on a bed,

sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book case

or rack, unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS

OR SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or

radiator, in direct sunlight, inside closed vehicles,

in high temperature [over 104°F (40°C)], or in over

75% humidity. If the unit is suddenly moved from

a cold place to a warm one, moisture may

condense in the unit and on the tape causing

damage. Never subject the unit to vibration,

impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a sloping

surface.

• Do not place this unit on any support that is not

firm, level, and adequately strong.

The unit could fall causing serious

injury to a child or adult and

damage to the unit.

• An appliance and cart

combination should be moved

with care. Quick stops,

excessive force, and uneven

surfaces may cause the appliance and cart

combination to overturn.

• Carefully follow all operating instructions and

use the manufacturer's recommended

accessories when operating this unit or

connecting it to any other equipment.

FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY

AND OPERATING INSTRUCTIONS. HEED ALL

WARNINGS IN THE MANUAL AND ON THE UNIT

USING THE UNIT

If the unit has been in storage or moved to a new location,

refer first to the INSTALLATION section of these safeguards.

KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR

STRONG IMPACT, unplug the unit and have it inspected by a

qualified service technician before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or

before leaving the unit unused for extended periods of time,

disconnect all equipment from the power source as well as

the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE

if liquid has been spilled into the unit. Immediately unplug

the unit, and have it inspected by a service technician.

Fire and shock hazards can result from electrical shorts

caused by liquid contact inside.

• Never drop or push any object through openings in the unit.

Some internal parts carry hazardous voltages and contact

can cause electric shock or fire hazard.

Do not put any foreign object on the disc tray.

• Avoid placing the unit directly above or below your TV set

as this may cause electrical interference. Keep all magnets

away from electronic equipment.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to

avoid risk of fire, shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated

cloth to gently remove dust or debris. DO NOT USE cleaning

fluids, aerosols, or forced air that could over-spray, or seep

into the unit and cause electrical shock. Any substance such

as wax, adhesive tape, etc. may mar the cabinet surface.

Exposure to greasy, humid, or dusty areas may adversely

affect internal parts.

SERVICE

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating

instructions, this product does not operate properly, do not

attempt to open or remove covers, or make any

adjustments not described in the manual. Unplug the unit

and contact a qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified

by the manufacturer, or those having the same safety

characteristics as the original parts. The use of unauthorized

substitutes may result in fire, electric shock, or other hazards.

HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service

technician to conduct a thorough safety check as

described in the manufacturer’s service literature to ensure

that the unit is in safe operating condition.

Important Safeguards and Precautions

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC

- NATIONAL

ELECTRICAL CODE

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the

equipment, be sure the antenna or cable system is grounded

so as to provide some protection against built up static

charges and voltage surges.

Section 810 of the National Electrical

Code, ANSI/NFPA 70 (in Canada,

part 1 of the Canadian Electrical

Code) provides information

with respect to proper grounding

of the mast and supporting

structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes and requirements for the grounding electrode.

KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

An outside antenna system should be located well away from

power lines, electric light or power circuits and where it will never

come into contact with these power sources if it should happen

to fall. When installing an outside antenna, extreme care should

be taken to avoid touching power lines, circuits or other power

sources as this could be fatal. Because of the hazards involved,

antenna installation should be left to a professional.

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:472

Region Management Information:

This DECK is designed and manufactured to respond to the

Region Management Information that is recorded on a DVD

disc. If the Region number described on the DVD disc does

not correspond to the Region number of this DECK, this

DECK cannot play this disc.

●The Region number for this DECK is “1”.

●The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

ALL

Example:

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol warns the user that uninsulated voltage

within the unit may have sufficient magnitude to cause

electric shock.

Therefore, it is dangerous to make any kind of contact

with any inside part of this unit.

This symbol alerts the user that important literature

concerning the operation and maintenance of this unit

has been included. Therefore, it should be read

carefully in order to avoid any problems.

Safety Precautions/Mesures de sécurité

WARNING: To prevent fire or shock hazard, do not expose this

equipment to rain or moisture.

CAUTION: To prevent electric shock, match wide blade of plug to

wide slot, fully insert.

Avertissement: Afin de prévenir tout risque d’incendie ou de chocs

électriques, ne pas exposer cet appareil à la pluie ou

à une humidité excessive.

Attention: Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de la

prise et pousser jusqu’au fond.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.

HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD

CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.

BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE

YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER

OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION

WHEN OPEN DO NOT

STARE INTO BEAM.

ATTENTION:

RAYONNEMENT

LASER EN CAS

D’OUVERTURE.

NE PAS REGARDER

DANS LE FAISCEAU.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when operated in a residential

environment. If this equipment does cause interference to radio or television reception, which can be

determined by turning the equipment off and on, use the equipment in another location and/or utilize

an electrical outlet different from that used by the receiver.

If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the

booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting to

other devices.) Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s

authority to operate.

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:473

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Before Using

Accessories

RF Coaxial Cable

LSJA0372

Batteries 2 “AA”

Remote Control

LSSQ0377

Loading the Batteries

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

1) Open cover.

3) Close cover.

2) Insert batteries as

marked.

Only use tapes with the mark in this DECK.

Record/ Playback Time

(Standard Play)

2 Hours

40 Minutes

1 Hour 2 Hours

5 Hours

20 Minutes

2 Hours 4 Hours

(Long Play)

3 Hours 6 Hours 8 Hours

SLP

(Super Long Play)

Type of Video Cassette

Tape Speed

Setting

T160T120T60

Congratulations

on your purchase of one of the most

sophisticated and reliable products on the

market today. Used properly, it will bring you

years of enjoyment. Please fill in the information

below. The serial number is on the tag located

on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

PV-D4763S

• Serial No.

To order accessories,

call toll free

1-800-332-5368.

Video Head Clog Sensor

During playback, this screen

appears if clogging is detected.

To remove screen, press PLAY

on the remote or DECK.

Playing older or damaged tapes may eventually cause

video heads to become clogged.

EO HEADS

EED

CLE

PLEASE

NSERT

HEAD

CLE

CASSE

REFER

MANUAL

END

Head Cleaning

Digital Auto Picture

Automatically controls the video output signal for

less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for

optimum picture quality.

Manual Tracking Control

(to reduce picture noise)

Use during Playback and Slow Motion mode to

reduce picture noise.

Press CH (TRACKING) / on the remote control

or on DECK until the picture clears up.

To return to Auto Tracking, press POWER off, then

on again a few seconds later.

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a

V-Lock control.

Features for a Quality Picture (VCR)

Built-in Head Cleaner

A clean video head helps produce a clear picture.

So, we have equipped your DECK with a built-in,

non-chemical head cleaning system that helps

prevent clogging of the video heads.

Cleaning is performed each time you load or unload

a video cassette.

• This feature is preventative only, If your video heads

are seriously clogged, consider the use of a chemical

non-abrasive head cleaning kit or take your DECK to

a Servicenter.

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.

Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your

nearest servicenter by visiting our Web Site

(see p. 65).

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:474

Table of Contents

Timer Recording..............................................................24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System ....................26, 27

Multi-Brand Control Feature ...........................................28, 29

Tape Operation (Search System) .......................................30 ~ 32

Special VCR Features .....................................................33, 34

Copying Your Tapes (Dubbing) .........................................................35

Disc Operation ...............................................................36 ~ 41

DVD-RAM Operation (DVD-RAM only).................................42, 43

DVD Operation using On-Screen Displays .................44 ~ 48

MP3/WMA/JPEG Playback Operation ..........................49 ~ 51

DVD Lock Feature .................................................................52

Settings for DVD Operation ..........................................53 ~ 57

SD Card............................................................................58, 59

Language Code List..............................................................60

DVD / VCR

Warning and Instruction Displays........................................61

Before Requesting Service.............................................62, 63

Limited Warranty .............................................................64, 65

Customer Services Directory ...............................................65

Spanish (Español) Quick Use Guide............................66 ~ 71

Index..................................................................................... BC

DVD / VCR

Important Safeguards and Precautions ............................2, 3

Before Using............................................................................4

DECK / Disc / Cassette Information .................................. 6 , 7

Location of Controls .......................................................8 ~ 10

Displays (On Screen Displays and Multi Function Display) ....................11

Connections ..................................................................12 ~ 15

Initial Setup for Basic Connections (Ready to Play) ..........16, 17

VCR

Reset Language, Channels, Clock, VCR’s Output Channel ...18, 19

Playback/ Record on a Tape...........................................20, 21

DVD

Basic DVD Operation ......................................................22, 23

Initial Setup

(Connection)

Basic

Operation

VCR

Operation

For Your

Information

DVD

Operation

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:475

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

DECK / Disc / Cassette Information

Prevent Accidental Tape Erasure

Record Tab

Cover the hole

with cellophane tape.

To record again

Break off the tab to

prevent recording.

Screw driver

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum

cleaner to remove dust from the ventilation holes on

the back sides and bottom of the cabinet. Plastic

surfaces are easily scratched and can be marred

by alcohol and various solvents. Avoid excessive

use of oil-based furniture polishes since the

materials used in the cabinet will accumulate more

dust. We recommend using a non-abrasive,

antistatic cleaner and polisher.

DVD-RAM discs

DVD-RAM discs must meet the following conditions

for this unit to be able to play them.

Type

• Non-cartridge discs

• Discs that can be removed from

their cartridges (TYPE 2 and 4)

Capacity

• 12 cm (5”) 9.4 GB (double-sided)

and 4.7 GB (single-sided)

• 8 cm (3”) 2.8 GB (double-sided)

• Remove TYPE 2 and 4 discs from their cartridges

before use, then return them when you are finished.

Read the instructions for the disc carefully.

• Some parts of the disc, for example where one program

ends and another begins, may not play smoothly.

DECK can play back discs bearing any of the

following marks:

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs (the audio on DVD-Audio can be

played), DVD-ROM, DVD-RW, DVD+RW,

CD-ROM, CDV, CD-G, CVD, SVCD, SACD,

Divx Video Disc and Photo-CD

[Discs Played 8cm (3") or 12cm (5")]

DVD (DVD-Video)

Video CD

CD (CD-DA)

CD-R/CD-RW (CD-DA,Video

CD formatted discs [finalized])

WMA, MP3, JPEG

DVD-Audio

Logo Disc type

DVD-R (DVD-Video formatted

discs [finalized])

Disc formats supported by this DECK

DVD-RAM (Version 1.1 of the

Video Recording Format a

unified video recording

standard)

Notes

• Do not use irregularly shaped discs (e.g. heart-

shaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW,

DVD-R and DVD-RAM in all cases due to the

type of disc or condition of the recording.

If disc is brought from a cold to a warm

environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth

before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Disc Handling

To clean disc surface

With a soft, damp (water only) cloth,

gently wipe from the center hole to the

outer edge as shown below. (Wiping in a

circular pattern will scratch the surface.)

• DVD-RAM, DVD-R :

Clean only with the DVD-RAM disc

cleaner available. Never use cloths or

cleaners for CDs etc.

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with

exposed adhesive from tape or left over peeled-off

stickers.)

• Only hold disc by edges as shown below. Fingerprints,

dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning

sprays, benzine, thinner,

static electricity prevention

liquids, or any other solvent.

• Do not try to close disc tray when disc is not

properly placed.

Disc tray

Disc

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:476

Power Source: 120 V AC, 60 Hz

Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts

Video Signal: EIA Standard NTSC color

Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)

Tuner:

Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69

CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)

Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output

Input Terminal: Audio/Video Line Input (Front)

Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Audio Output 2 (L), (R)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)

Operating Humidity: 10 % ~ 75 %

Weight: 4.9 kg (10.8 lbs).

Dimensions: 430 (W) x 95.5 (H) x 344 (D) mm

16-15/16” (W) x 3-12/16” (H) x 13-9/16” (D) inch

Discs Played

(1) DVD-Video Disc 5” (12 cm) single-sided single-layer

DVD-Audio Disc 5” (12 cm) single-sided double-layer

5” (12 cm) double-sided double-layer (one layer per side)

3” (8 cm) single-sided single-layer

3” (8 cm) single-sided double-layer

3” (8 cm) double-sided double-layer (one layer per side)

DVD-RAM Disc 5” (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)

3” (8 cm) 2.8 GB (double-sided)

(2) Compact Disc 5” (12 cm) disc

(CD-DA, Video CD) 3” (8 cm) disc

(CD-R/CD-RW, MP3, WMA, JPEG)

Digital Audio Output: Digital Optical Connector

Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)

Laser power: CLASS II

Specifications

Note: • Designs and specifications are subject to change without notice.

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

The ANGLE button can be used to view the scene from different angles.

(ANGLE Indicator lights on DECK when a scene recorded at different angles

is detected.)

Chapter Number: Titles are subdivided into numbered sections. You can quickly search for

a favorite scene using these numbers.

DVD: A high-density optical disc on which high-quality pictures and sound have

been digitally recorded. DVD incorporates new video compression technology

(MPEG II) and high-density recording technology which allow entire movies to

be recorded with incredible playback quality.

Playback Control: With Video CD (version 2.0), scenes or information may be selected for viewing

or listening from an interactive menu that appears on the TV screen.

Subtitles: Written dialogue which appears at the bottom of the screen.

Time Number: The elapsed play time from the start of a disc or title. Use to quickly find

scenes. (May not work with some discs.)

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.

Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to

be quickly located.

Video CD: CD containing picture and sound with same quality level as video tape.

This DECK also supports Video CDs with playback control (version 2.0).

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098 and 4,907,093,

licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method claims of

certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and

other rights owners. Use of this copyright protection technology must be authorized by Macrovision

Corporation, and is intended for home and other limited viewing uses only unless otherwise

authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Initial Setup

(Connection)

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:477

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Location of Controls

Remote Control

Bold: VCR Function

Italic

DVD Function

Bold Italic

VCR and DVD Functions

Normal: Others

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

This button is inoperative if pressed during recording.

If pressed in DVD mode, the disc tray opens or closes.

ZOOM

. 37

POWER

DSS

CABLE mode

p. 28

SPEED

PAGE

pp. 21,

NUMBER keys

TV mode

p. 28

EJECT

OPEN

pp. 20,

ACTION

pp. 18

, 53

PAUSE

STILL

pp. 20,

COUNTER

RESET

p. 32

PROGRAM

p. 24

RECORD

p. 21

ADD/DELETE

CLEAR

pp. 19,

39, 52

VCR mode

p. 28

VOLUME

p. 28

CHANNEL

TRACKING

V-LOCK

pp. 4, 21

PLAY

pp. 20,

REWIND

SLOW-

pp. 20,

DVD mode

p. 28

INPUT

p. 35

COMMERCIAL SKIP

ZERO SEARCH

pp. 31, 32

DISPLAY

pp. 11,

STOP

pp. 20,

ANGLE

. 37

SUB TITLE

. 36

VCR/TV

p. 21

RETURN

. 22,

AUDIO

(SAP / Hi-Fi)

pp. 27,

SELECT

SKIP

. 23

FAST FORWARD

SLOW+

pp. 20,

TITLE

Direct Navigator

pp.

38, 42

Play List

pp.

38, 43

SET

Virtual Surround Sound (V.S.S.)

ENTER

23,

TAPE POSITION

VOLUME ADJUST

pp. 34,

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:478

Initial Setup

(Connection)

Front View of DECK

Audio/Video

Input Connector 2

(LINE 2)

p. 35

CHANNEL /

TRACKING/V-LOCK

pp. 4, 21

POWER

PAUSE

OPEN/CLOSE

STOP/EJECT

p. 20

Multi Function

Display

p. 11

REC

p. 21

Disc Tray

Cassette

Compartment

PLAY

p. 20

Remote

Sensor

FAST FORWARD/SEARCH

p. 20

REWIND/SEARCH

p. 20

Front View of DECK

SKIP

STOP

Bold: VCR Function

Italic

DVD Function

Bold Italic

VCR and DVD Functions

Normal: Others

PROGRESSIVE

p. 10

PLAY

SD Card slot

p. 58

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid

wire (e.g. an extended paper clip) and,

applying moderate force, insert it straight

into the hole at the base of the tray.

The tray will eject a little. Now, pull the tray

all the way out and remove the disc.

Over 2 inches

Use when moving DECK to new location, or if a mistake was made in the Initial

Setup section (return to Factory Setting).

• Make sure a tape is not inserted in the DECK.

Reset All Memory Functions

Press and hold both VCR PLAY

and CHANNEL

on the DECK for

more than 5 seconds.

• The power shuts off.

Turn DECK Power on.

Do “Initial Setup (Ready to Play)”

on page 16.

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:479

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Location of Controls (continued)

Rear View of DECK

AC Power Plug

S-Video Out

Connector

(DVD Only)

pp.

10, 13

Component Video Output

Connector (Y, P

, P

) (DVD Only)

Audio Output 2

Connector (L/R)

Optical Digital Audio

Output Connector

(DVD Only)

Video Input

Connector

p. 35

Video Output

Connector

Audio Output 1

Connector (L/R)

VHF/UHF Antenna Input Terminal

p. 12

VHF/UHF Antenna Output Terminal

p. 12

• While plugged into an AC outlet,

this DECK consumes 4 W of

electrical power in off mode.

••

The following table shows the status of the output jacks when in VCR or DVD mode.

Bold: VCR Function

Italic

DVD Function

Bold Italic

VCR and DVD Functions

Note

• PROG functions on the remote are not available when using Component Video Output

and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press

PROG.

Video Output

Audio Out 1

Audio Out 2

Component

Video Output

S-VIDEO OUT

VCR

DVD

YES

N/A

To enjoy PROGRESSIVE SCAN video

(1).Connect

Component Video Output

to the component video input terminals of a television.

(See p. 13.)

(2).When the PROGRESSIVE button is pressed, the ON lamp lights up (see p. 9) and the

PROGRESSIVE SCAN signal is output from the

Component Video Output Connector

Notes

• The PROGRESSIVE button can be operated when the DECK is in DVD function mode.

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• The DECK outputs video signals (not PROGRESSIVE SCAN) from the “VIDEO OUT” and

“S-VIDEO OUT” terminals when the ON lamp is lit.

YES

Audio Input

Connector (L/R)

•

5.1ch Analog Audio Output

Connector (CENTER, SUB WOOFER,

SURROUND L/R, FRONT L/R)

(DVD Only)

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4710

VCR

TIMER REC

DIGIT

DVD

MP3

WMA

ANGLE

REC

SAP

ONO

VCR Status & Clock Displays

Blank Tape/ No Video Signal

Indications

Whenever a blank section of a tape

comes up in Play mode, or when the

selected channel has no broadcast

signal with Weak Signal Display

Feature (p. 33) set to OFF, the TV

screen will turn solid blue.

Function Status

Rec Time Remaining

(OTR mode only,

see p. 21.)

Current Time

Channel

Tape Speed

(See p. 4.)

Broadcast Audio

Being Received

(See p. 26.)

When a function button

is pressed, e.g. PLAY,

or you change

channels, a 5-second

display appears.

Counter

Displays (On Screen & Multi Function)

To display or remove

overlay at right,

➛➛

➛ press DISPLAY.

Multi Function Display

On Screen Displays (VCR)

Function & Channel Displays

CH 0

VCR mode Indicator

Lights up when

DECK is VCR mode.

Hi-Fi Indicator

Lights up when

Hi-Fi audio is

monitored in Play

mode.

Timer Indicator

Lights up when

DECK is set for

Timer Recording,

or when One

Touch Recording

(OTR) is used.

Flashes when

Timer Recording is

set, but a tape has

not been inserted

into DECK and

when a power

interruption occurs

during Timer

Programming.

VCR REC Indicator

Lights up during

recording.

DTS Indicator

Lights up when DTS

formatted DVD is played.

(DVD only)

Dolby Digital

Indicator

Lights up when “Dolby Digital”

formatted DVD is played.

(DVD only)

Clock/ Status/ Channel/ Speed Display

Displays the current time. Briefly displays DECK

status when a function button is pressed. Briefly

displays the channel number, or “L1” or “L2”

when a channel or line input is selected. Briefly

displays the recording speed when SPEED is

pressed.

DVD mode Indicator

Lights up when

DECK is DVD mode.

AM/PM

Indicator

Initial Setup

(Connection)

ANGLE Indicator

Lights up when a

scene recorded at

different angles is

detected.

(See p. 37.)

(DVD only).

CD/MP3/WMA

Indicator

:Lights when a

Video or Audio

CD is inserted.

MP3/WMA :

Lights when an

MP3 or WMA

file is played.

Tape Indicator

Lights up when a tape

is inserted.

DISC Indicator

Lights up when a

disc is inserted.

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4711

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Connections

1 Disconnect antenna or cable from TV

and connect to DECK.

WARNING

When using “Nut type” RF coaxial cables, tighten with

fingers only. Overtightening may damage terminals.

Basic Connections

• Connect DECK and TV with an RF Coaxial Cable

(supplied) or an AV Cable

(not supplied) as shown in the figure below.

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

FROM

ANT.

OUT

AUDIO

IN 1

OUT

DVD/VCR DECK

VHF/UHF

VIDEO

VHF/

UHF

VIDEO

AUDIO IN

AV CABLE

(not supplied)

2 Connect DECK to TV with RF Coaxial Cable.

DSS

Receiver

OUT

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the

NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as practical.

OUT

Antenna or Cable

Cable Box

■ ■

■ DECK TV

■ ■

■ DSS Receiver DECK TV

■ ■

■ Cable Box DECK TV

RF COAXIAL CABLE

(supplied)

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4712

You CannotYou Can

• record and view

both scrambled

and unscrambled

channels if

additional

equipment is

added.

This connection

requires: two

converter boxes,

an A/B switch,

and a 2-way

splitter.

• view a channel

other than the

one selected

for any type of

recording.

• do a Timer

recording of a

channel unless

you select it on

the Cable Box.

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

IN 2IN 1

Cable Box

OUTIN

OUT 2

OUT 1

2-Way Splitter

OUT

A/B Switch

■■

■

Connect With Two Cable Boxes

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

Cable Box

OUTIN

OUT

VIDEO

AUDIO

ANT or CATV

You CannotYou Can

• record

scrambled

channels.

• view any

(including

scrambled)

channel.

• use Remote

Control to select

channels without

using Multi-brand

control feature.

ANT

CATV

VIDEO

AUDIO

OUT

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT

or S-VIDEO mode).

If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to

S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

Connections For DVD Only (enjoying higher picture quality)

Other Connections

Notes

DVD/VCR DECK

VHF/

UHF

Cable Box

VHF/

UHF

■ ■

■ With a Cable Box (DECK

Cable Box TV)

Initial Setup

(Connection)

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,

and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only

from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT

Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use

PROGRESSIVE mode. Consult your TV operating instructions.

VIDEO

AUDIO

COMPONENT

VIDEO OUT

AUDIO OUT2

S-VIDEO OUT

DVD OUTPUT

P R

S-VIDEO

From DECK’s

A/V OUTPUT

DVD/VCR DECK

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4713

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected,

off before proceeding with connection.

Do not block ventilation holes of any of the equipment and arrange them so that air can

circulate freely.

Read through the instructions before connecting other equipment.

Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system)

Speaker

Amplifier

Speaker

AUDIO OUT2

AUDIO IN

R L

DVD/VCR DECK

Notes on audio output from the optical digital audio output connector

Enjoying digital audio output from the digital audio output connector

*1 The type of audio output from the connector can be selected by the Settings for DVD

Operation. (See p. 54.)

*2 Sound having 96/192 kHz sampling is converted into 48 kHz sampling (or 88.2/176.4 kHz

sampling is converted into 44.1 kHz sampling) when it is output from the DECK’s optical digital

audio output connector.

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories

Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel)

sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,

DVDs are recorded in 44.1 kHz/16 bit ~ 192 kHz/24 bit.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942, 5,956,674,

5,974,380, 5,978,762 and other world-wide patents issued and pending. “DTS” and “DTS Digital

Disc

DVD

Video CD

MP3

WMA

Sound recording format

Dolby Digital

Linear PCM

(48/96/192/44.1/88.2/

176.4 kHz 16/20/24bit)

DTS

MPEG 1

Linear PCM

MP3

WMA

Optical digital audio output from connector

Dolby Digital bitstream (1 - 5.1 ch)

or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2 ch)

(48 kHz sampling/16 bit or 44.1 kHz sampling/

16 bit)*

Bitstream or PCM (48 kHz sampling/16 bit only)*

PCM (44.1 kHz sampling)

Linear PCM (44.1 kHz sampling)

Linear PCM (It depends on the MP3 file)

Linear PCM (It depends on the WMA file)

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4714

Enjoy the powerful movie theater and hall-like sound available with multiple

channel audio found on DVDs by connecting an amplifier and speakers.

There are two types of connection, digital and analog.

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not

contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital”

and “PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 54).

Otherwise, any attempt to play DVDs may cause such a high level of noise that it may

be harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or

“Dolby Digital” of the Settings for DVD Operation “Audio Output”.

If “PCM” is selected, there will be stereo sound. (See p. 54.)

• Video CDs and CDs can be played as usual.

Note:

• Some DTS decoders which do not support DVD-DTS interface may not work properly with

DECK.

■ Connecting Amplifier (5.1 ch Surround system)

A.Digital connection (DECK OPTICAL Digital Audio Output Connector)

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS

bitstream is output from the DECK OPTICAL Digital Audio Output Connector. When DECK

is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality

audio in your home. [An optical digital audio cable (optional) is required when an optional

Dolby Digital decoder or DTS decoder is used.]

B.Analog connection (5.1 ch Analog Audio Output Connector)

Connect an amplifier with multi-channel audio input terminals. This DECK can decode

Dolby Digital and DTS. There are no limitations on sampling frequency with this kind of

connection.

Initial Setup

(Connection)

DVD/VCR DECK (Rear)

Decoder with Dolby

Digital /DTS processing

Optical Digital Audio

Cable (optional)

To Optical Digital Audio

Input Connector

Notes on connecting an optical

digital audio cable (optional)

• Firmly connect the cable to the

connector.

A.Digital connection

Front

Speaker

Front

Speaker

Surround

Speaker

Surround

Speaker

Center

Speaker

Subwoofer

B.Analog connection

Amplifier

To multi-channel audio

input terminals

[5.1 ch Surround system]

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4715

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Before doing Initial Setup

Initial Setup for Basic Connections (Ready to Play)

Turn TV on.

See connections

RF Coaxial Cable Connection and

AV Cable Connection on page 12.

Set TV to channel 3.

Set TV to VIDEO.

[DECK

➛➛

➛ TV]

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

➛➛

➛ DECK

➛➛

➛ TV], [DSS

➛➛

➛ DECK

➛➛

➛ TV]

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

in your time zone.

• If you use a DSS Receiver, it must be turned off.

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel

and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

channel 3, try switching it to channel 4.

• To change VCR’s output channel, please refer to “VCR’s Output Channel” on page 19.

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

CH AUTO SET PROCEEDING

CANCEL : STOP

Plugging the AC Power Plug into

an AC outlet

Initial Setup (Ready to Play)

• Function buttons are inoperative during Initial Setup.

• To remove a cassette during Auto Set, press EJECT on

the remote or STOP/EJECT twice on the DECK.

In this case, settings must be made manually. (See p. 18.)

• Depending on conditions, Auto Clock Set may take longer

than 30 minutes. If so, press STOP to stop setup and

perform settings manually. (See p. 18.)

Notes

Continued on next page...

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4716

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Settings are made automatically.

When setup is done, this screen appears.

If “AUTO CLOCK SET IS INCOMPLETE”

appears, manually set clock. See below.

SUN

20P

SETT

: CH

AUTO CLOCK SET

PLETED

If Auto Clock Set was incomplete.

Press ACTION* on remote to display

CLOCK screen.

Press

to select the month and SET to

set. In the same manner, select and set the

date, year, time, and DST (Daylight Saving

Time).

Press ACTION to start clock and exit.

ET BACK :

ACT

2003

SUN

SET

Manual Clock Set

AUTO CLOCK SET IS

PLETE

PLEASE SET CLOCK BY

PRESSING

ACT

ON KEY

DST

/ /

SELE

SET

EXIT

ACT

SET

VCR

ACTION

SET

SELECT

Initial Setup

(Connection)

EJECT

STOP

dy to Play)

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4717

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

Clock

2) Press to select

“MANUAL,” and press SET.

(For Auto Clock Set, select

“AUTO CLOCK SET.”)

3) Press and to

select, then set the date,

time, and DST (Daylight

Saving Time).

4) Press ACTION to start

Clock and exit this

mode.

(“TIME ZONE ADJUST”

appears only when auto

clock is set.)

SEL.

QUITTER

: ACTION

REGLER:SET

REGLAGE MAGNETOSCOPE

REGLAGE HORLOGE

REGLAGE CANAL

SD CARD LECTURE

LANGUAGE/IDIOMA:FRANÇAIS

CA SORTIE : 3

ELEGIR

SALIR

: ACTION

FIJAR : SET

PREPARAR VCR

FIJAR RELOJ

FIJAR CANAL

SD CARD REPRODUCCION

LANGUE/LANGUAGE:ESPAÑOL

CANAL DE SALIDA : 3

SELECT

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

Language

2) Press SET repeatedly to

change language item as

shown below.

For English

For Spanish

For French

1) Press to select

language item.

Reset Language, Channels, Clock, VCR’s

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

Channels

2) Press to select

“ANTENNA,” then

press SET to set your

antenna system

(“TV” or “CABLE.”)

3) Press to select

“AUTO SET,” then

press SET.

• If you use a Cable Box,

set it to the PBS channel

in your time zone.

• After Channel Auto Set

is finished, Auto Clock

Set will be performed.

Press ACTION*

to display MENU.

SELECT

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

3) Press ACTION to exit.

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

SELE

SET

EXIT

ACT

ANT

ENN

CABLE

SPLA

OFF

ABLE

DSS

X SET UP

Plus

H SET UP

SET UP

NNE

AUT

K SET

NUNU

JUS

SELE

SET

EXIT

ACT

SET

20032003

SUN

1212

SELECT

OUROUR

SET

SELE

SET

SET BACK :

EXIT

ACT

1) Press to select

“SET UP CHANNEL,”

and press SET.

1) Press to select

“SET CLOCK,” and

press SET.

• PROGRAM functions are not available

when using COMPONENT Video Output

and S-VIDEO OUT. Please set TV to

either RF INPUT or VIDEO INPUT, and

then press PROGRAM.

CH AUTO SET PROCEEDING

CANCEL : STOP

➡

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4718

Add or Delete a Channel

To add channel:

Select channel with NUMBER keys

and press ADD/DLT.

To delete channel:

Select channel with CH / or

NUMBER keys and press ADD/DLT.

HANNEL

ADDED

HANNEL

Time Zone Adjust

2) Press to select

“TIME ZONE ADJUST,”

VCR’s Output

Channel

1) Press to select

“VCR’S OUTPUT CH.,”

and press SET.

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

2) Press SET.

3) Press ACTION.

After 3 seconds

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

• To Make Corrections,

repeat steps 1) ~ 3).

DST (Daylight Saving Time)

DECK auto adjusts clock for DST.

(p. 17.)

Spring (First Sunday in April)

DST:ON

➛➛

➛ Sets clock ahead one hour.

Autumn (Last Sunday in October)

DST:ON

➛➛

➛ Turns clock back one hour.

• If your area does not observe

Daylight Saving Time, select

DST:OFF.

• Keep these time changes in mind

when programming DECK for

timer recordings.

1) Press to select

“SET CLOCK,” and

press SET.

and press SET to

subtract or add hour(s)

as necessary.

*Important: If a remote control button does not work

when pressed, press the VCR button

on the remote and try the button again.

(Only when Auto Clock is set.)

3) Press ACTION twice.

•“TIME ZONE ADJUST”

returns to “0” if clock is

set manually.

YOU

PRESS

ACT

KEY, VCR’

UTPUT

TCHES

PLEASE

TUNE

SELE

SET

EXIT

ACT

SET

AUT

K SET

JUS

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

ADD/DLT

NUMBER

keys

POWER

ACTION

VCR

SET

SELECT

➡

Basic

Operation

k, VCR’s Output Channel

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4719

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Playback/ Record on a Tape

Insert a tape.

Playback using DECK buttons

Press PLAY.

Multi Function Display

Press STOP/EJECT to stop

and/ or eject a tape.

Ready Checklist

All connections are made. (pp. 12 ~ 15)

TV and DECK are plugged in.

TV is on and tuned to CH 3, 4, or VIDEO.

Remote is in VCR mode. (Press VCR.)

Insert a tape.

• DECK power comes on. If Auto VCR/TV (see

p. 32) is set to “OFF,” press VCR/TV on the

remote to be VCR mode.

• If tape has no rec. tab (p. 6), auto play begins.

Special Features During Play

Press REW/SLOW- or FF/SLOW+ in Stop

mode to rewind or fast forward a tape.

Press EJECT on remote, or STOP/EJECT

on DECK to eject a tape.

Press STOP to stop a tape.

Press PLAY* to play a tape.

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛

➛ Press PLAY to release.

After search has begun, each additional press of

FF or REW changes speed as shown below.

[SLP] : Approx. 21X

↔ Approx. 9X

[LP] : Approx. 9X

↔ Approx. 7X

[SP] : Approx. 7X

↔ Approx. 3X

If at 21X, 9X, or 7X speed the picture is

interrupted, change speed to 9X, 7X, or 3X.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛

➛ Press PLAY to release.

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛

➛ Press PLAY to release.

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

REW/SLOW- (decrease speed) in Still

mode.

➛➛

➛ Press PLAY to release.

Playback a Tape

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary

depending on current tape position.

Notes

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual Tracking

Control” on page 4.

• After DECK is in Still or Slow mode for 3 minutes,

it will switch to Stop mode automatically to

protect the tape and the video head.

Notes

PAUSE/

STILL

REW/SLOW-

STOP

FF/SLOW+

EJECT

CH /

SPEED

REC

VCR/TV

PLAY

DVD

VCR

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4720

Insert a tape with a record tab (p. 6).

• DECK power comes on. If Auto VCR/TV (see p. 32)

is set to “OFF,” press VCR/TV on the remote to be

VCR mode.

Press CH , or NUMBER keys

to select the channel.

• For “LINE” input, see p. 35.

• If channel is over 100, press 100 key then press

the remaining 2 digits.

Press SPEED

to select the record speed (p. 4).

SP = Standard Play LP = Long Play

SLP = Super Long Play

Press REC

to start recording.

(The VCR REC indicator lights up on Multi Function

Display),

• To edit out unwanted scenes, press PAUSE/STILL

to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

• It is not possible to record from DVD/ Video

CD/ CD to VHS tape using DECK.

• Watching one channel and recording another

is not possible when using Cable Box or

DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to

protect a tape and video heads.

• Speed appears on-screen and on Multi Function Display.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Remove loose or peeling

labels from tapes to prevent

tape jam.

Multi Function Display

Record using DECK buttons

Select

Channel.

Press REC

to start

recording.

Press STOP/EJECT to stop.

This video recorder, equipped with HQ

(High Quality) system, is compatible

with existing VHS equipment. Only use

tapes with the mark. Only tapes

tested and inspected for use in 2, 4, 6,

and 8 hour machines are

recommended.

Normal Rec

0:30 1:00

1:302:003:004:00

Insert a tape.

Note

Notes

One Touch Recording (recording in progress),

➛➛

➛ press REC repeatedly to set the recording length

➛➛

➛ (30 min. ~ 4 hours).

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV on the remote

(change to TV mode),

➛➛

➛ select channels at TV (recording continues).

Select Channels at DECK (In STOP or

REC. PAUSE mode),

➛➛

➛ press VCR/TV on the remote

(change to TV mode),

➛➛

➛ select channels at DECK.

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛

➛ press

DVD

, and then press

PLAY

Basic

Operation

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4721

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15)

DECK is plugged in.

If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

Interactive DVD...

May include multiple camera angles,

stories, etc.

Video CD with playback control...

Particular scenes or information can be

interactively selected from a menu that

appears on the screen.

Operation using DECK buttons

Press PLAY.

Insert a disc.

Press

OPEN/CLOSE.

Press STOP.

Press

POWER.

3, 7

Press or

NUMBER keys

(see

below) to select title,

and press

SET

PLAY

to start playing.

Press

POWER*

on the remote or DECK.

Press

DVD

to select DVD mode.

Press

OPEN/CLOSE

and then place a disc into the disc tray.

• If a disc is already inserted, go to step 4.

(Depending on the disc, playback may

start automatically.)

Press

PLAY

to start playing.

Disc tray closes automatically.

If an interactive DVD*

a Video CD with playback

control*

is used and TITLE

MENU appears, go to step 5.

• You may also close tray by

pressing

OPEN/CLOSE

• Data reading time differs with

each disc.

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

1 digit number 1 ••• 1

2 digit number 12 ••• 10 1 2

3 digit number 123 •••100 1 2 3

Press

SKIP

| or | to go to next or previous

menu screen.

• SKIP function not available with all discs.

Please refer to disc jacket for operation information.

To return to menu (play stops)

Press

TITLE, MENU,

RETURN

. (DVD-Video/

DVD-Audio)

Press

RETURN

. (Video CD)

Press

STOP

to stop playing.

Press

OPEN/CLOSE

to eject the disc.

• Hold disc by its edges

only (p. 4) with printed

side up and use guides

to place into tray.

Use 3” (8 cm)

or 5” (12 cm) disc.

READING

TLE MENU

Cas

Love

Dogs

•“Pressing

SET

PLAY

”

is not necessary when

using

NUMBER keys.

<Input

Example>

OPEN/

SET

FF/

SLOW+

STOP

RETURN

POWER

REW/

SLOW-

NUMBER

keys

TITLE

PLAY

DVD

PAUSE/

STILL

SELECT

VSS

SKIP

DVD-RAM ➡ see p. 42

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4722

■ Forward/Reverse Scene Search

Press

FF/SLOW+

REW/SLOW-

during play.

Press

PLAY

to release.

• Starting forward/reverse search during play

started from menu on Video CDs may recall menu.

• Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

■ Forward/Reverse Chapter/Track Skip

Press

SKIP

| or |

SKIP

during play.

Each press skips a chapter (DVD-Video) or

track (DVD-Audio/Video CD/CD).

• Pressing |

SKIP

once midway through a

chapter/track returns to the start of that

chapter/track. Each additional press skips

back one chapter/track.

• Pressing

SKIP

| or | during play started

from menu on Video CDs may recall menu.

■Still Picture or Pause

Press

PAUSE/STILL

during play.

Press

PLAY

to release.

•DVD/Video CD : DECK will enter still picture mode.

•CD : DECK will enter pause mode.

■ Frame by Frame Picture

(DVD/Video CD)

Press

PAUSE/STILL

in still mode.

Press

PLAY

to release.

•Each press advances picture one frame.

•Hold button down for consecutive frame advance.

•Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 57.)

■Slow Motion Picture

(DVD/Video CD)

Press

FF/SLOW+

REW/SLOW-

in still mode.

Press

PLAY

to release.

•Slow motion speed, slow at first, is increased

with each additional press of the button up to

5 levels.

•Reverse slow motion is not available for Video CDs.

• When appears on the screen while a button

is being operated, it means that the

corresponding operation is prohibited by DECK

or the disc.

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Reverse Skip Forward Skip

Current playback position

Chapter/Track Chapter/Track Chapter/

rackChapter/

rack

Power turns off after DECK has been in

Stop mode (DVD) for about 5 minutes.

Auto-Power Off Function

Basic

Operation

• Please read the disc jacket for operation

information.

• If a single sided disc is placed in upside

down, “THIS TYPE OF DISC CANNOT BE

PLAYED. PLEASE INSERT A DIFFERENT

DISC” is displayed.

• Remove disc and press DECK POWER off

when not in use.

• Disc continues to rotate with menu displayed

even after play is done.

Press STOP to clear menu display when

finished with menu.

DECK memorizes the point where STOP is

pressed (STOP is displayed on screen).

Press

PLAY

to resume play from this point.

Pressing

STOP

again or opening the tray

cancels RESUME, however, RESUME is not

canceled when power is turned off and on.

• RESUME works only with discs for which

elapsed play time is displayed during play.

Resume Function

Notes

1. Do steps 1-4 (previous page).

When menu appears, press

STOP

2. Press

NUMBER keys

to select desired

track (play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,

Press

STOP

and press

PLAY

, then the

menu will be displayed.

Now, go to step 5 (previous page).

Enjoy Video CDs featuring

playback control without using

menus (Video CDs only)

V.S.S. (Virtual Surround Sound)

Press

VSS

in DVD mode.

• The Surround sound effects can be

changed by pressing VSS repeatedly as

shown by the figure below.

• Surround sound effects is available in DVD

mode only.

• Turn off the surround effects on the other

equipment.

• V.S.S. will not work, or will have less effect,

with some discs.

• Turn V.S.S. off if it causes distortion.

• Sound will only come from the two front

speakers if V.S.S. is on.

Enjoy a surround-like effect if you are

using two front speakers only. The effect

is broadened and sound seems to come

from virtual speakers on either side if the

disc has surround signals recorded on it.

Note

VSS OFF

VSS OFF (default)

VSS1

VSS3

VSS2

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4723

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Timer Recording

Press PROG*

to display Program.

Press PROG

to end programming.

DAILY

SELECT /

Selection Order

WEEKLY

(SAT)

WEEKLY

(MON)

WEEKLY

(SUN)

Example

Today

2) To set remaining items,

press

to select and

press SET

to set START/ STOP times,

CH (channel) or LINE

input (p. 35), and tape

speed (SP, LP, SLP).

To Enter More Programs,

press

to select and

press SET

to set an unused program

number, and then repeat

step 2.

Press PROG

to exit.

1) To set record DATE,

press

to select:

1~31= one time, or

DAILY= MON~ FRI, or

WEEKLY= same time

each week and

press SET.

• See selection order left.

START

SUN

--:--

DATE START ST

SLP

SELE

SET

END

STA

SPD

13 10

DLT

SELECT 1-8

NTER

: SET

EXIT

Ready Checklist

All connections are made. (pp. 12 ~ 15)

TV and DECK are plugged in.

Clock set correctly. (p. 18)

Tape has rec.tab. (p. 6)

Remote is in VCR mode. (Press VCR.)

Sufficient tape remaining for recording time.

• The “Timer” Indicator lights up on DECK.

• You can do Timer Recording with the power on or off.

•“TIMER REC WILL START SOON” appears on-screen for 2 minutes

before Timer Recording starts. If DECK is in DVD mode, no message

appears, but the VCR REC Indicator, the VCR mode indicator and

“REC” will flash on Multi function Display.

VCR REC Indicator

VCR mode Indicator

TIMER Indicator

ADD/DLT

POWER

SET

PROG

SELECT

VCR

TIMER REC

VCR

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4724

To Replace program...

To Clear program...

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Important notes when using DSS Receiver

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

DLT

SELECT

1-8 :

ENTER : SET

EXIT

: PROG

STA

SPD

7 9

DLT

SELECT

1-8 :

ENTER : SET

EXIT

: PROG

STA

SPD

Press ADD/DLT.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Press

to select number and

press SET

to display.

To cancel a Timer

Recording in progress...

Repeat Step 2 (p. 24)

to set new programs.

Press PROG

to end the programming.

Hold down STOP in VCR mode for

a few seconds to cancel the Timer

Recording.

(The “TIMER” Indicator goes out

on Multi Function Display.)

• Any future daily or weekly recording

will be performed as programmed.

SUN

00A

----------------------------------------

DATE

TART

TOP

START

SELE

SET

BACK :

END

Notes

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to

the Cable Box input channel and Cable Box must be manually set to the desired

channel. Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER

REC” appears and Timer Indicator flashes.

Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be

canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION”

appears on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back,

Timer Recording will not be performed.

Press PROG

to display Program List.

VCR

Operation

D4763S P1-25 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4725

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

MONO broadcast

Normal monaural sound broadcast.

SAP broadcast

Secondary Audio Program (sub

language) broadcast. Select SAP

audio mode for the sub language.

MTS Stereo broadcast

Multi-channel Television Sound

Stereo broadcast. Select STEREO

audio mode.

• If stereo broadcast is weak and

display flickers, select MONO audio

mode for possible better results.

MTS Stereo and SAP broadcast

Multi-channel Television Sound

Stereo (main language) and

Secondary Audio Program (sub

language) broadcasts are being

received simultaneously.

Select STEREO or SAP audio mode.

The following are possible audio broadcast types and on-

screen displays.

The signal being received is indicated with an “

” mark

while the selected audio mode is indicated with an arrow.

Receivable Broadcast Types

MTS Broadcast/ VHS Hi-Fi Stereo System

Equipped with

-TV

Noise Reduction for

true MTS reproduction.

-TV Noise

Reduction is required

for good stereo

separation and audio

fidelity.

is a

registered trademark,

and is licensed by

Technology Licensing.

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

To display the broadcast signal being received,

➛➛

➛ press DISPLAY*.

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

STER

SAP

ONO

AUDIO

(SAP/Hi-Fi)

DISPLAY

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4726

Audio Mode for Recording

Make a recording.

See page 21.

Audio Mode for Playback

Start playback.

See page 20.

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard

stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to

a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

• Arrow indicates

selection.

• Refer to “Receivable Broadcast Types” on page 26.

• Arrow indicates selection.

• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo

recordings in stereo sound.

Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

to select desired mode.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

Press AUDIO (SAP/Hi-Fi) repeatedly

to select desired mode.

STER

SAP

ONO

Notes

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

: L

ORM

VCR

Operation

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4727

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Multi-Brand Control Feature

DSS/

CABLE

POWER

ENTER

NUMBER

keys

VCR

DVD

The Remote Control can be set to control some TV and

Cable Box/DSS functions.

Find your TV and Cable Box/DSS Receiver

Brand Code Number on the following page.

Set up for TV control,

➛➛

➛ hold down TV button,

➛➛

➛ enter code with NUMBER keys.

Multi-Brand Control Setup

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

Set up for Cable or DSS control,

➛➛

➛ hold down DSS/CABLE button,

➛➛

➛ enter code with NUMBER keys.

• If code number is 100 or greater,

➛ e.g., press 1 - 0 - 2 for 102.

• Repeat setup after remote battery replacement.

• Remote will not control every TV, Cable Box, or

DSS made by the manufacturer listed. If you get

no response, your particular unit cannot be

controlled. There are NO additional codes for the

products listed. If your product is not listed, then

the remote is not compatible with that product.

Notes

Mode

Unit

DVD/VCR TV

DVD/VCR

All

POWER, INPUT,

NUMBER keys,

ENTER,

CH / ,

VOL

EJECT/

OPEN/CLOSE

DISPLAY

PLAY

STOP

FF/SLOW+

REW/SLOW-

VCR/TV, PAUSE

/STILL

SKIP

AUDIO

, CM/ZERO,

TAPE POSITION,

COUNTER RESET, SPEED,

REC,

PAGE

After remote is set up, you can select VCR, DVD, TV, or

DSS/CABLE for the desired function.

Press VCR,

DVD

, TV, or DSS/CABLE on the remote.

(Table below shows available remote buttons for each mode.)

CABLE/ DSS

Using Multi-Brand Control

CABLE/

DSS

POWER, ENTER,

NUMBER keys

(except 100key),

CH /

• Not all functions listed may be controllable.

• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing

NUMBER keys for channel selection.

Notes

VOL

VOL +/-

* Bold: VCR Function

Bold Italic: VCR and DVD Functions

Italic: DVD Function

Normal: TV, Cable Box or DSS Receiver

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4728

• Some manufacturers use several codes for one brand. If the first code entered fails, try the

next one listed.

• Some TV, Cable Box and DSS Receiver brands require you to turn on the power manually.

Cable Box Brand Code Numbers

Panasonic ....................... 01, 02

Quasar ............................ 01, 02

RCA ....................................... 03

GE ......................................... 03

Zenith .................................... 04

Magnavox.............................. 05

TV Brand Code Numbers

Sylvania ................................ 05

Sharp ............................... 06, 07

Sony ...................................... 08

Toshiba ................................. 09

Sanyo .................................... 10

Fisher .................................... 10

JVC........................................ 11

Hitachi ................................... 12

Mitsubishi ........................ 07, 13

Samsung ............................... 14

Gold Star...................15, 16, 17

DSS Brand Code Numbers

Important Notes

Archer ......................... 44, 06, 01, 120, 05, 63, 126

Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30

52, 04, 124, 126

Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126

Curtis ..................................... 08, 09, 25, 61, 53, 87

Century ...................................... 44, 51, 75, 59, 126

Cabletenna .................. 29, 09, 01, 63, 120, 44, 126

Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126

Diamond ...................... 29, 09, 01, 63, 120, 44, 126

Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107

Eastern ................................................... 28, 29, 130

Explorer.................................. 08, 09, 25, 61, 53, 87

Gemini .....................................................30, 04, 124

General Electric ......................................01, 57, 120

General Instruments . 01, 84, 83, 34, 03, 02, 04, 55

65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124

Gerrard............................................... 44, 51, 75, 59

GC Electronics ............... 44, 42, 63, 29, 30, 52, 04

124, 126

Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130

Hitachi ................................................................... 31

Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66

67, 68, 120, 106, 121, 122, 115, 117, 118, 124

Jasco ...................................................... 30, 04, 124

Macom ................................................................... 31

Magnavox...................................................... 26, 112

Matsushita ................................. 17, 16, 08, 87, 109

Movietime ...................... 32, 39, 42, 44, 126, 38, 40

Maestro ........................................................... 74, 35

NEC .................................................... 40, 19, 38, 32

NSC .................................................... 40, 19, 38, 32

Novavision ............................. 08, 09, 25, 61, 53, 87

Next Level...........01, 84, 83, 34, 03, 02, 04, 55, 65

66, 67, 68, 120, 106, 121, 122

Oak................................................. 46, 11, 129, 101

Oak Sigma ..................................... 46, 11, 129, 101

Panasonic .................................. 17, 16, 08, 87, 109

Philips ................... 23, 24, 20, 13, 07, 50, 128, 129

Pioneer...................................................... 06, 05, 12

Pulsar.................... 04, 42, 63, 44, 30, 52, 124, 126

Quest ........................................................ 06, 05, 12

Radio Shack ............................... 44, 51, 75, 59, 126

RCA ............................................ 17, 16, 08, 87, 109

Realistic ..................................... 44, 51, 75, 59, 126

Recoton...................................... 44, 51, 75, 59, 126

Regal ................. 41, 14, 15, 28, 102, 104, 103, 130

Regency ..................................................28, 29, 130

Rembrandt ....... 44, 42, 63, 29, 01, 32, 39, 120, 126

Samsung ...................................... 42, 06, 32, 05, 40

Scientific Atlanta ................... 08, 09, 25, 61, 53, 87

Sheritech............................................................... 27

Signal ............................................................ 26, 112

SL Marx............. 42, 06, 32, 40, 43, 44, 52, 63, 126

Sprucer ...................................... 17, 16, 08, 87, 109

Standard Components ............... 32, 39, 42, 44, 126

Stargate ..............04, 42, 32, 40, 63, 44, 30, 52, 06

124, 126

Sylvania .......................................................... 19, 18

Teknika ........................................................... 74, 35

Telecaption.................................................... 77, 127

Teleview ................................. 40, 19, 38, 32, 42, 06

Texscan .......................................................... 19, 18

Tocom ...................................34, 33, 01, 42, 66, 120

Toshiba ................................................................. 36

Unika ........................... 44, 42, 63, 29, 01, 126, 120

Universal ..............................52, 43, 44, 63, 42, 126

Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107

Videoway.......................................... 07, 23, 50, 129

Vidtek.................................................................... 64

Zenith ............................................... 07, 23, 50, 129

Toshiba....................................................... 90

Hitachi/ Hughes.................................... 91, 99

Primestar .................................................... 92

Drake .......................................................... 93

Magnavox............................................. 94, 95

Uniden................................................... 94, 95

Optimus ................................................94, 95

Panasonic................................................... 96

ProScan...................................................... 97

RCA............................................................. 97

SONY.................................................. 98, 105

VCR

Operation

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4729

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Index Search

Note

• If Index Search is started very close to an

index mark, that index mark may not be

counted in the search.

Tape Operation

Search System

For each recording, an invisible index mark is placed on the tape. A program index and

information are also included for timer recordings. These marks are used to access or

scan recordings.

Program End Search

Fig. 1

Fig. 2

Fig. 3

Note

Locates end point of recording for continuity.

Examples of Program End Search.

If search exceeds

a few seconds in

BLANK area.

➛➛

➛ search continues 7 sec. past end point,

➛➛

➛ tape rewinds to 10 sec. before end point,

➛➛

➛ tape plays to end point and stops.

Upon locating end point,

• If Program End Search is started very close to

an index mark, that mark may be skipped over.

PROGRAM END SEARCH

SEARCH START : FF

EXIT

:SEARCH

Program 2 or BLANK

Program 1

the current tape position

Press SEARCH button

INDEX

End Point

Program 2

Program 1

the current tape position

Press SEARCH button

INDEX

BLANK

End Point

Program 2

Program 1

the current tape position

Press SEARCH button

BLANK

INDEX

End Point

INDEX SEARCH

ENTER INDEX NUMBER :1

USING

9 KEYS

FORWARD SEARCH :FF

REVERSE

SEARCH :REW

NEXT :SEARCH

EXIT

:STOP

INDEX SEARCH

FORWARD SEARCH : FF

REVERSE

SEARCH : REW

Press SEARCH*

to display SEARCH

in Stop or Play

mode, and then

press NUMBER

keys

to select recording

number.

• To calculate

number, see below.

Press FF/SLOW+

or REW/SLOW- on

the remote to start

search.

Press SEARCH twice

to display SEARCH in Stop or Play

mode.

Press FF/SLOW+

on the remote to

start PROGRAM

END SEARCH.

• To cancel, press

PLAY or STOP.

Play begins at

search end.

To search forward

or back 1 index,

press FF/SLOW+ or

REW/SLOW- on the

remote while

screen left is

displayed (10 sec.).

• To cancel, press

PLAY or STOP.

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

NOTE: indicates start points of each recording.

61572 34

17534 62

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4730

Auto Play

Insert a tape ➛ Power comes on,

➛ Play starts if there is no record tab

(see p. 6).

Auto Rewind

Play

Fast Forward

Play Auto Eject

(Repeat Play must be off)

Play

➛ ➛

➛ Tape end

➛ ➛

➛ Rewind

➛ ➛

➛ Tape ejects if set some programs

Auto Operation Functions

Commercial Skip

VCR fast forwards (skips) over 1~3 minutes

of recorded tape.

Press CM/ZERO in Play mode.

PLAY

1st Press

2nd Press

3rd Press

1 min Skip

2 min Skip

3 min Skip

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

• No indication appears on-screen.

• The skip time can be changed by

pressing CM/ZERO repeatedly as

shown by the figure below.

➛ Tape end ➛ Rewind

REW/SLOW-

FF/SLOW+

PLAY

NUMBER

keys

CM/ZERO

STOP

VCR

Operation

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4731

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Tape Operation (continued)

Repeat Play

Set to playback a recording over and over.

Zero Search

To quickly return to a specified tape location.

Continue to record, playback etc.

Press STOP.

• DECK will go into FF or REW mode and stop

at the last point the Counter was set to 0:00:00.

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

PLAY

Press ACTION*

to display MENU.

Press

to select “SET UP VCR,” and

press SET.

• Play repeats at tape end or if unrecorded portion

over 30 sec. is detected.

Press ACTION twice

to return to normal screen.

Press DISPLAY during play

to display Counter.

Press COUNTER RESET

at desired position to reset

to “0:00:00”.

Press CM/ZERO

in Stop mode

to start Zero Search.

Press

to select “REPEAT PLAY,”

and press SET

to set “ON” or “OFF.”

REPEAT

PLAY

OTE

ARN

AUT

SHU

OFF

AUT

VCR/TV

SELE

SET

END

ACT

SET

UP V

Note

• For repeat play in DVD mode, see page 48.

REW

STOP

VCR/TV Selector FeatureVCR/TV Selector Feature

The VCR/TV selection can be set to

auto or manual.

REPEAT

PLAY

OTE

ARN

AUT

SHU

OFF

AUT

VCR/TV

SELE

SET

END

ACT

SET

UP V

Press ACTION

to display MENU.

Press

to select

“AUTO VCR/

TV,” and

press SET

to set “ON”

or “OFF.”

Press ACTION

to return to normal screen.

Note

• OFF(Manual):You select “VCR” or

“TV” mode using the

VCR/TV button on the

remote.

• ON(Auto): “VCR” mode is

automatically set when

VCR is turned on, or in

Play mode.

• For more on VCR/TV selection, see

“Record one station, watch another”

and “Select channels at DECK”

sections (see p. 21).

Press

to select

“SET UP

VCR,” and

press SET.

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4732

Weak Signal Display Feature

When “ON,” picture is displayed regardless of signal

strength.

• ON: Picture is displayed regardless of signal

condition, and may not always be clearly visible.

OFF: Screen turns solid blue when signal is weak or

non-existent.

• Selecting ON has no effect on connected equipment

with blue back feature.

Press ACTION twice

to return to normal screen.

Press

to select “SET UP

CHANNEL,” and

press SET.

Press

to select “WEAK SIGNAL

DISPLAY,” and

press SET

to set “ON” or “OFF.”

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

Press ACTION

to display MENU.

SELE

SET

EXIT

ACT

ANT

ENN

ABLE

SPLA

OFF

SET UP

NNE

Special VCR Features

*Important: If a remote control button does not work

when pressed, press the VCR button

on the remote and try the button again.

When set to ON, all operations

except for timer record and tape

eject are prohibited. Useful for

households with small children.

VCR Lock Feature

K ACT

TED

• VCR Lock cancels in 24 hours if

clock is set.

To turn off, repeat above.

To turn on, hold down REC on

DECK in Stop mode with no

tape inserted for 7 seconds.

(Please ignore “NO CASSETTE”

warning.)

REC

Auto Shut-Off Feature

The power shuts off at a preset time.

Press

to select “AUTO SHUT-OFF.”

Press SET repeatedly to

change shutoff time as

shown below.

Press ACTION twice

to return to normal screen.

Press ACTION

to display MENU.

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

Press

to select “SET UP VCR,” and

press SET.

REPEAT

PLAY

OTE

ARN

AUT

SHU

OFF

AUT

VCR/TV

SELE

SET

EXIT

ACT

SET

UP V

OFF

2 Hours

6 Hours

4 Hours

• The shut-off countdown will not function during Play or

Record.

Note

COUNTER

RESET

DISPLAY

ACTION

SET

CM/ZERO

STOP

SELECT

VCR

Operation

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4733

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Special VCR Features (continued)

If Multi-brand feature is used (p. 28), and this feature is

set to on, a warning appears whenever an invalid key

is pressed in TV, DSS or CABLE mode.

• If “OFF,” remote warning will not appear

when invalid key is pressed.

Press ACTION*

to display MENU.

Press

to select

“REMOTE WARNING,” and

press SET

to set “ON” or “OFF.”

Press ACTION twice

to return to normal screen.

Remote Warning Feature

Press

to select “SET UP VCR,”

and

press SET.

SELECT

EXIT

: ACTION

SET : SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

REPEAT

PLAY

OTE

ARN

AUT

SHU

OFF

AUT

VCR/TV

SELE

SET

EXIT

ACT

SET

UP V

*Important: If a remote control button does not work

when pressed, press the VCR button

on the remote and try the button again.

To find out the present tape position and amount of tape remaining.

Tape position is displayed for VHS-C type Cassettes, tapes

under 30 minute long, and some other tapes, but the

position is not correct.

• Tape remaining time display may not be

precise.

END

R 120 M

•“DETECTING TAPE POSITION” is displayed

only when a cassette is first inserted, and it

takes several seconds for correct tape

position to appear.

Tape Position and Tape Status Feature

Press TAPE POSITION

to return to normal screen.

• The present tape position indication and

amount of tape remaining (according to

tape speed) is displayed.

DETECTING TAPE POSITION

Press TAPE POSITION

to detect current tape position.

This function cannot display exact amount of tape remaining for

tapes 30 minutes or less, or for tapes over 120 minutes in length.

Note

INPUT

ACTION

SET

TAPE

POSITION

SELECT

STOP

REC

PAUSE/

STILL

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4734

Copying Your Tapes (Dubbing)

Insert a pre-recorded tape.

Insert a blank tape with record tab.

Press REC, then PAUSE/STILL

immediately to enter REC/PAUSE

mode.

Press INPUT to set DECK Input mode to

LINE for Video Input.

(See “Selecting the Input Mode” below.)

Press PLAY to start dubbing.

Playing VCR starts playback.

Press PAUSE/STILL to start dubbing.

DECK starts recording.

Press STOP to stop dubbing.

Caution:• Unauthorized exchanging and/or copying of copyrighted recordings may be

• Please note that some tapes cannot be dubbed on DECK. Also, it is not

possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.

Playing (Source) VCR Recording (Editing) DECK

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording

VCR channel (CH 3 or CH 4).

2 If Auto VCR/TV (see p. 32) is set to

“OFF,” press VCR/TV on the remote to

be VCR mode.

Note

• Dubbing tapes protected with Copy

Guard will result in poor quality

recordings.

Connection

Press STOP to stop dubbing.

Press PLAY, then PAUSE/STILL

immediately to enter PLAY/PAUSE

mode.

The operation of steps 4 and 5 must be done on the

playing and recording VCRs at the same time.

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.

To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R”

AUDIO IN terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder.

Simply connect the unit’s Audio/Video outputs to DECK.

Selecting the Input Mode

Method 1: Press INPUT repeatedly.

Channel Number

↔↔

↔ LINE1

↔↔

↔ LINE2

Method 2: Press CH / .

Display will change as below.

Front of DECK

VIDEO IN 2

L-AUDIO IN2-R

(Audio/Video In Terminals

on the front of DECK are

available)

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

VHF/

UHF

DVD/VCR DECK

VIDEO

AUDIO

VCR/ Camcorder (Hi-Fi)

VIDEO

AUDIO

•“L1” or “L2” lights up on Multi Function Display

(about 4 seconds) when LINE1 or LINE2 is selected.

• LINE1: For rear audio/video connection.

LINE2: For front audio/video connection.

125

LINE1

(CABLE)

(TV)

LINE2

Press

VCR

Operation

D4763S P26-35 (030512 –§”Ô•Ï•X).p65 2003/05/14, 13:4735

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

AUDIO: 3 ESP

3 ESP

Dolby Digital 3/2.1ch

Hola

SELECT

END

:AUDIO

AUDIO

AUDIO: 1 ENG

1 ENG

Dolby Digital 3/2.1ch

Hello

SELECT

END

:AUDIO

AUDIO

Te amo

You can select a different subtitle language (if offered) than

the one set at the Settings for DVD Operation.

(See p. 53.)

Press

to select a language.

Press

to select “ON” or “OFF.”

Subtitle Language (DVD only)

• Display disappears after

5 seconds.

• When no subtitles are offered,

“-” will be displayed instead of

the language number.

Press

SUB TITLE

in Play mode to display

the subtitle selection

on-screen.

Ready Checklist

Please read “Basic DVD Operation”

on page 22.

You can change the audio soundtrack language, selected

at the Settings for DVD Operation, to a different language

if available. (See p. 53.)

(This operation works only with discs on which multiple

audio soundtrack languages are recorded.)

Press

AUDIO

in Play mode to display the

audio selection on-screen.

Audio Soundtrack Language (DVD only)

Disc Operation

Subtitle language being played back (see chart, right).

Press

to select desired language.

Audio soundtrack language being played back (see chart,

above right).

• Display disappears after

5 seconds.

Audio attribute 1 type, sampling

frequency, bit No. of the disc or

number of speaker channel.

• If after several presses of the button the language does not

change, language selection is not offered on the disc.

• When disc is removed, subtitles revert to initial setting

language. If the initial language is not recorded on the disc,

the disc’s priority language will appear.

• With DVD-RAM, the subtitle can only be set to ON/OFF.

The subtitle language cannot be selected.

Notes

[Subtitle language]

[Audio sound track language]

• Change the No. by pressing ,

and press

SET

[Audio attribute 1 type, sampling

frequency, bit No. of the disc (see p. 54.)]

LPCM

Dolby Digital

DTS

44.1 kHz

192 kHz

1 ch - 5.1 ch

16 bit

20 bit

24 bit

Linear PCM disc

Dolby Digital disc

DTS disc

• If, after several presses of the AUDIO

button the language does not change,

language selection is not offered on the

disc.

• When disc is removed, language

reverts to initial setting. If this language

is not recorded on the disc, the

language recorded will be heard.

• With DVD-RAM, Audio Soundtrack

Language cannot be set. Audio stream

and Audio mode (LR/L/R) setting can

be made. Audio stream operation

method is the same as Audio

Soundtrack Language. Press to

move the cursor to Audio mode, then

press to select LR/ L/ R.

Notes

AUDIO: 1 LR

Dolby Digital 3/2.1ch

SELECTSELECT

END END :AUDIOAUDIO

ENG

FRA

DEU

ITA

ESP

NLD

English

French

German

Italian

Spanish

Dutch

SVE

NOR

DAN

POR

RUS

JPN

Swedish

Norwegian

Danish

Portuguese

Russian

Japanese

CHI

KOR

MAL

VIE

THA

∗

Chinese

Korean

Malay

Vietnamese

Thai

Other

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4736

SELECT :

When appears on the screen while

a button is being operated, it means

that the corresponding operation is

prohibited by DECK or the disc.

• The ANGLE Indicator lights up on

DECK when a scene recorded at

different angles is detected.

• The angle number can be set

beforehand so that the angle is

switched whenever the ANGLE

Indicator lights up.

ANGLE Indicator

Press

AUDIO

in Play mode

to display the audio screen.

Vocal Selection for Karaoke Discs

(DVD/Video CD)

DVDs may contain scenes shot from multiple camera

angles allowing the same scene to be viewed at different

angles. You can view these angles, if available, using the

ANGLE button.

Press

ANGLE

in Play mode to display the

angle selection on-screen.

• Display disappears after

5 seconds.

Multiple Angle Viewing (DVD only)

Press

to select the desired

angle.

Press (or )

to select as shown below,

and

press

(or ) to set.

(DVD only)

Number of angle being played back.

You can enlarge specific portions of a picture and

select the zoom ratio using the ZOOM button during

DVD playback.

Press

ZOOM

repeatedly to change display

as follows.

Picture Zoom (DVD-Video/DVD-RAM only)

• You can enlarge the center portion of the image

to one of 2 magnifications.

• The subtitle cannot be enlarged nor

can it’s position be changed.

• The picture zoom feature does not

work with a Video CD.

• During picture zoom, “ZOOM1” or

“ZOOM2” appears on-screen for 5

seconds.

• Zooming, on some discs, may result

in poor picture quality, or may not

operate at all.

■ Use the , , and buttons to move the position

up, down, left and right.

Notes

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

AUDIO

SET

ANGLE

SUB TITLE

ZOOM

SELECT

DVD

Operation

SELECT :

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

• Video CD LR L R

SELECT :

END :AUDIO

This function not available with DVD-RAM.

Note

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4737

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Some DVDs have more than one title, e.g. movies.

If the disc offers a title menu, you can select the desired

title number. (Operation may vary according to the disc.)

Press

TITLE

in Play mode

to display the title screen.

Title Menu (DVD only)

DVDs may offer a special menu. This menu may include

guides to unique contents, audio/subtitle languages, etc.

Although contents and operation may vary, the following

steps show basic steps for using the menu.

Press

in Play mode to display

DVD MENU.

Press or

NUMBER keys

to select an item, and

press

SET

PLAY

to perform.

DVD Menu (DVD only)

Press or

NUMBER keys

to select a title, and

press

SET

PLAY

to start playing.

Disc Operation (continued)

•“Pressing

SET

PLAY

” is

not necessary when using

NUMBER keys.

T I TLE MENU

Cas

Love

Dogs

TLE MENU

Cas

Love

Dogs

DVD MENU

3 . ANGLE

1 . SUBT

TLE

2 . AUD

DVD MENU

3 . ANGLE

1 . SUBT

TLE

2 . AUD

rds

of the world

Repeat step 2 if there is

more than one menu.

•“Pressing

SET

PLAY

” is

not necessary when using

NUMBER keys.

SET

STOP

PLAY

NUMBER

keys

TITLE

CLEAR

ACTION

SELECT

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4738

You can program specific tracks and order of play.

Program Play (Video CD/CD only)

Ready Checklist

DECK is in DVD mode, press DVD.

Video CD or CD is inserted.

Press

ACTION

to display DVD MAIN MENU.

Press

to select

“PLAY MODE,” and

press

SET

to display.

Press

to select

“PROGRAM PLAY,”

and

press

SET

to display.

Press

to select “START,” and

press

SET

to start play

of programs in the

sequence selected.

• To cancel, press

STOP

during play, then press

CLEAR

Press

to select a track

number (Track

numbers on disc are

displayed.), and

press

SET

• Repeat step 4 to select another track.

• The selected track is added on the right side.

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STI LL MODE : AUTO

TV MODE : 4:3 Letterbox

PARENTAL

LOCK

LEVEL 8

PLAY MODE

SELECT :

SET : SET

END : ACTION

PROGRAM PLAY

RANDOM PLAY

SELECT :

SET : SET

END : ACTION

DISC PROGRAM

1 61116 5 8

2 7 12 17 15 6

3 8 13 18 1 13

4 91419 3 2

5101520 2

CLEAR LAST

CLEAR ALL START

PROGRAM PLAY

SELECT :

SET : SET

END : ACTION

DISC PROGRAM

1 61116 5 8

2 7 12 17 15 6

3 8 13 18 1 13

4 9 14 19 3 2

5101520 2

CLEAR LAST

CLEAR ALL START

Notes

Program Repeat Play

(Video CD/CD only)

Press

SET

to enter Select mode.

Cursor move to “OFF.”

Press to select “DISC.”

(DECK Information Screen)

Do operation steps 1 through 5

at left on this page.

Press

DISPLAY

to display Disc

Information screen.

(Disc Information Screen)

Press

DISPLAY

to display

DECK Information screen.

Press

SET

to set mode.

Cursor move to “REPEAT.”

To cancel, select “REPEAT :

OFF” in step 5, then press

SET

SELECT:

SET : SET END : DISPLAY

PLAY

REPEAT : DISC

PROGRAM PLAY

SET : SET END :DISPLAY

SET : SET NEXT:DISPLAY

TRACK : 1 VIDEO CD

PBC : OFF 01:35 :12

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

• Up to 15 tracks can be programmed.

•“ ” or “ ” (depending on disc) indicates additional

PROGRAM PLAY screen.

Press for next or previous screen.

• To clear the last program one by one

Press to move to “CLEAR LAST” and

press

SET

. (Pressing

CLEAR

on remote control

also clears last program.)

• To clear all programs

Press to move to “CLEAR ALL” and press

SET.

(Programs are also cleared when the power

is turned off or the disc is removed.)

DVD

Operation

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4739

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Tracks are played in a random order.

Random Play (Video CD/CD only)

Press

ACTION

to display DVD MAIN MENU.

Disc Operation (continued)

Press

to select “PLAY MODE,”

and

press

SET

to display.

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STI LL MODE : AUTO

TV MODE : 4 :3 L et t er b ox

PARENTAL

LOCK

LEVEL 8

PLAY MODE

Press

to select

“RANDOM PLAY,” and

press

SET

to begin random play.

• To cancel, press

STOP

during play, then press

CLEAR

PLAY MODE

SELECT :

SET : SET

END : ACTION

PROGRAM PLAY

RANDOM PLAY

Ready Checklist

DECK is in DVD mode, press DVD.

Notes

SELECT

STOP

CLEAR

ACTION

SET

VOLUME

ADJUST

DISPLAY

NUMBER

keys

PAGE

•“ON” is set ..... When a DVD is played back, the average volume is increased.

•“OFF” is set.... The volume level recorded on the disc is played back just as it is.

Setting the VOLUME ADJUST

Press

VOL.ADJ

repeatedly to change “ON”

↔↔

↔ “OFF.”

•“ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when

press VOL.ADJ.

Some DVD

[Volume level is low]

VOLUME ADJUST “OFF”

Volume is the original level.

VOLUME ADJUST “ON”

Volume level is increased

when played back.

Some DVDs are recorded in lower than average volume levels.

For these DVDs, this DECK can be set so that the average volume

is increased.

• This feature is available only for Dolby Digital sound tracks.

• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.

• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4740

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

DVD

Operation

DVD-Audio Operation

Bonus Group playback

Some DVD-Audio discs contain Bonus Group tracks which can be played by entering a

4-digit secret code.

Press

DISPLAY

in stop mode to display “On-Screen Displays.”

Press to select “GROUP,” and press

SET

Press or

NUMBER keys

to select bonus group

number, and press

SET

(see pp. 44, 45.)

Press

NUMBER keys

to enter bonus group secret code, and press

SET

To Make Corrections

Press

repeatedly to move the cursor.

Press

NUMBER keys

to make the correction.

Notes

Press

CLEAR

to return to normal screen.

Note

• When the proper secret code has been entered, Bonus Group track 1 playback

begins. If a mistake is made, the secret code enter screen is redisplayed.

• If the proper secret code is already entered, Bonus Group tracks can be

selected. (Secret code enter screen is skipped.)

• This code is specifically for the disc and differs from Parental Lock secret code

(p. 52). Please refer to disc jacket instructions.

• During playback, Bonus Group tracks cannot be selected.

SELECT:

SET : SET NEXT : DISPLAY

GROUP : 2 DVD-AUDIO

TRACK : 1 00: 12: 34

BONUS GROUP

ENTER 4

CODE

----

This DECK, equipped with a 192 kHz/ 24 bit Audio D/A converter, supports DVD-Audio

recorded with high quality sound.

The DVD-Audio feature includes “Still Image Skip” and “Bonus Group Playback”

functions. (See below.)

Please refer to “Basic DVD Operation” on pages 22 and 23.

Still Image Skip

DVD-Audio still images (only if contained) can be skipped over.

Press

PAGE

in Play or Pause mode to display the still image and page

number.

PAGE : 1

SELECT :

Each press of PAGE changes page number as shown below.

• Pressing PAGE on the last page returns to PAGE 1.

SELECT :

PAGE : 2

• Still Image Skip function not available with all discs.

PAGE

1 PAGE

2 PAGE

3 ....... PAGE

Press PAGE

Note

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4741

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Page 1/4

Direct Navigator

No. Date Length Title

2002/12/24

5:15:41AM

00:01:00

Drama

2002/12/25

4:31:49AM

00:03:12

Pana NEWS

2002/12/25

8:24:25AM

00:15:01

Tigers vs.Giants

2002/12/25

12:45:00AM

00:03:00

Dinosaur

SET : SET END:TITLE

SELECT:

DVD-RAM Operation (DVD-RAM only)

Do steps 1 ~ 3 on page 22.

• This DECK was designed for playback only. DVD-RAM recording is not possible.

You can enjoy playing your personally recorded/edited DVD-RAM discs on this DECK.

Note

Press

TITLE*

to display Direct Navigator

or Play List menu for easy title or scene selection.

Press

STOP

to stop playing.

Press

OPEN/CLOSE

to eject the disc.

Press

TITLE

in Play/Stop mode to display the Direct Navigator

menu.

Press to select a page and press

select a title (Program No.).

Then, press

SET

PLAY

to start playing.

If the DVD-RAM features Direct Navigator, a list of recorded titles is displayed. Simply select a title

number and start playback. (Operation can vary with disc used.)

Direct Navigator

•“Pressing SET or PLAY” is not necessary when

using NUMBER keys.

Program No.

Titles

Recording

time length

Recording time

and date

Page No.

<Input

Example>

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

1 digit number 1 ••• 1

2 digit number 12 ••• 10 1 2

3 digit number 123 •••100 1 2 3

Press

TITLE

to clear Direct navigator menu.

(Press

ACTION

to display DVD MAIN menu.)

Play a DVD-RAM

• Play begins from the first program title recorded on

the DVD-RAM.

• See below for Direct Navigator or next page for Play

List information.

(Example)

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4742

Page 1/5

Play List

No.

Date

Length

Title

2002/12/24

5:15:41AM

00:01:00

Movie Picture

Playback

2002/12/25

4:31:49AM

00:03:12

Still Picture

Playback

2002/12/25

8:24:25AM

00:15:01

Hybrid Playback

SELECT:

SET :SET

END:MENU

2002/12/25

12:45:00AM

00:03:00

Partial Playback

Press

in Play/Stop mode to display the Play List menu.

Press to select a page and press

select a title (Play List No.).

Then, press

SET

PLAY

to start playing.

If the DVD-RAM features a Play List, your preselected list of favorite scenes is displayed for easy

access. (Operation can vary according to how you edited the DVD-RAM.)

Play List

•“Pressing SET or PLAY” is not necessary when

using NUMBER keys.

TitlesRecording time

and date

Page No.

<Input

Example>

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

1 digit number 1 ••• 1

2 digit number 12 ••• 10 1 2

3 digit number 123 •••100 1 2 3

Press

to clear Play List menu.

(Press

ACTION

to display DVD MAIN menu.)

Play List No.

Established

time length

(Example)

• Titles of Direct Navigator and Play List cannot be changed using this DECK.

• With Direct Navigator, up to 99 programs can be displayed. With Play List, up to 99 titles (999

scenes) can be displayed.

• While DVD MAIN MENU is displayed, Direct Navigator and Play List display will not appear even

if TITLE or MENU is pressed.

• When appears on the screen while a button is being operated, it means that the

corresponding operation is prohibited by DECK or the disc.

Notes

SET

STOP

NUMBER

keys

TITLE

PLAY

SELECT

DVD

Operation

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4743

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Notes

• When

DISPLAY

button is pressed

during playback of a Video CD with

Playback control,

NUMBER keys

are

not available on the displayed screen.

In this case, press

DISPLAY

again to

remove the displayed screen.

• When appears on the screen while

a button is being operated, it means

that the corresponding operation is

prohibited by DECK or the disc.

DVD Operation using On-Screen Displays

Ready Checklist

DECK is in DVD mode, press DVD.

SET

NUMBER

keys

DISPLAY

SELECT

CLEAR

Press

DISPLAY*

in Play or Stop mode

to display “On-Screen Displays.”

When

DISPLAY

is pressed, On-Screen Displays show

disc information (title/chapter/track number, elapsed

playing time) and DECK information (repeat play, play

mode).

• Each press of

DISPLAY

changes the on-screen

display as follows. (Refer to pp. 44 ~ 48.)

Note

Press or

NUMBER keys

to select the setting, and press

SET

Press (or )

to select

an item, and

press

SET

Selected disc information

Selected DECK information

Normal Screen

➡

•

DISPLAY

button does not function while DVD MAIN

MENU or Direct Navigator or Play List is displayed.

• When numbers are

displayed (e.g. title

number),

NUMBER keys

are also available.

• If the number entered is

not on the disc, the entry

will have no effect.

Re-enter the correct

number.

• For more details, refer to

the disc operation

information.

To return to normal

screen,

press

CLEAR

DISPLAY

repeatedly.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4744

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

DVD

Operation

Detailed Descriptions of each On-Screen Display

■■

■ Disc information screen (for DVD-Video)

1. TITLE No.

•Select “TITLE”, and press

SET

•Change the No. by pressing or

NUMBER keys

, and press

SET

2. CHAPTER No.

•Select “CHAPTER”, and press

SET

•Change the No. by pressing or

NUMBER keys

, and press

SET

3. Disc currently being played

4. Elapsed playing time

The screen may be changed by selecting the elapsed time.

•Select the elapsed playing time (“xx:xx:xx”), and press

SET

•Change the elapsed time by pressing

NUMBER keys

Hours ➛ Minutes ➛ Seconds are entered in order.

If the time entered is not on the disc, the entry will have no effect.

Re-enter the correct time.

e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

•This function does not work with some discs.

Hour Minutes Seconds

■■

■ Disc information screen (for DVD-Audio)

A.GROUP No.

•Select “GROUP”, and press

SET

•Change the No. by pressing or

NUMBER keys

, and press

SET

B.TRACK No.

•Select “TRACK”, and press

SET

•Change the No. by pressing or

NUMBER keys

, and press

SET

C.Disc currently being played

D.Elapsed playing time

The screen may be changed by selecting the elapsed time.

•Select the elapsed playing time (“xx:xx:xx”), and press

SET

•Change the elapsed time by pressing

NUMBER keys

Hours ➛ Minutes ➛ Seconds are entered in order.

If the time entered is not on the disc, the entry will have no effect.

Re-enter the correct time.

e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

•This function does not work with some discs.

Hour Minutes Seconds

• When appears on the screen while a button is being operated, it means that the

corresponding operation is prohibited by DECK or the disc.

Note

SELECT:

SET : SET NEXT:DISPLAY

TI TLE : 1 DVD

CHAPTER: 12 01 :12: 55

ENTER : 0

SET : SET NEXT:DISPLAY

TI TLE : 1 DVD

CHAPTER: 12 01 :

ENTER : 0

SET : SET NEXT:DISPLAY

GROUP : 1 DVD-AUDIO

TRACK : 1 01:

If SET is pressed while

making entries, unit returns

to the condition it was in

before entries were made.

If SET is pressed

while making entries,

unit returns to the

condition it was in

before entries were

made.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4745

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

SET : SET NEXT:DISPLAY

TRACK : 1 VIDEO CD

PBC : OFF 01:35 :12

PLAY L

ST: 1 DVD-RAM

00:12:34

SET : SET NEXT : DISPLAY

SELECT:

ENTER : 0

SET : SET NEXT:DISPLAY

PROGRAM: 1 DVD-RAM

01:

■■

■ Disc information screen (for Video CD/ CD)

1. TRACK No.

•Select “TRACK”, and press

SET*

•Change the No. by pressing or

NUMBER keys

, and press

SET

2. Playback control ON/OFF

[Video CD with playback control only]

3. Disc currently being played

4. Elapsed playing time

• Track No. and the elapsed playing time are not displayed during play started from

menu of Video CDs with playback control.

• When appears on the screen while a button is being operated, it means that the

corresponding operation is prohibited by DECK or the disc.

■■

■ Disc information screen (for DVD-RAM)

A.Direct Navigation (PROGRAM) or PLAY LIST No.

•Select “PROGRAM” or “PLAY LIST”, and press

SET

•Change the No. by pressing or

NUMBER keys

, and press

SET

B.Disc currently being played

C.Elapsed playing time

The screen may be changed by selecting the elapsed time.

•Select the elapsed playing time (“xx:xx:xx”), and press

SET

•Change the elapsed time by pressing

NUMBER keys

Hours ➛ Minutes ➛ Seconds are entered in order. If the time

entered is not on the disc, the entry will have no effect.

Re-enter the correct time.

e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.

•This function does not work with some discs.

Hour Minutes Seconds

If SET is pressed while

making entries, unit

returns to the condition

it was in before entries

were made.

Direct Navigation

(PROGRAM)

PLAY LIST

DVD Operation using On-Screen Displays (continued)

Notes

Video CD CD

ON Video CD menu play is displayed.

OFF Video CD menu play is not displayed.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4746

DVD

Operation

. Repeat Play

■■

■ DECK information screen (for DECK)

DVD-Video CHAPTER TITLE OFF

DVD-Audio TRACK GROUP OFF

DVD-RAM (PROGRAM) PROGRAM DISC OFF

(PLAY LIST) PLAY LIST ALL PLAY LIST OFF

Video CD/CD TRACK DISC OFF

•Select “REPEAT”, and press

SET

•Change the desired mode during play by pressing , and press

SET

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

. Play mode [Video CD/ CD only] (See p. 39 or 40.)

SELECT:

SET : SET END : DISPLAY

PLAY

REPEATREPEAT : OFF

SET : SET END :DISPLAY

PLAY

REPEAT REPEAT : DISC

RANDOM PLAY

NUMBER

keys

SELECT

SET

PROGRAM PLAY program play

RANDOM PLAY random play

----

normal play

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4747

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

DVD Operation using On-Screen Displays (continued)

•

CHAPTER/TITLE REPEAT PLAY (DVD-Video)

•

TRACK/DISC REPEAT PLAY (Video CD/CD)

For your reference

•

TRACK/GROUP REPEAT PLAY (DVD-Audio)

• For repeat play in VCR mode, see p. 32.

Note

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

•

PROGRAM/DISC REPEAT PLAY (DVD-RAM [PROGRAM])

•

PLAY LIST/ALL PLAY LIST REPEAT PLAY (DVD-RAM [PLAY LIST])

TITLE

chapter

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

track

TRACK REPEAT

DISC REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

track

TRACK REPEAT

GROUP REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

track

GROUP

PROGRAM

PROGRAM REPEAT

DISC REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

PROGRAM

PLAY LIST

PLAY LIST REPEAT

ALL PLAY LIST REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

PLAY LIST

OPEN/

SET

POWER

PLAY

SELECT

SKIP

NUMBER

keys

ACTION

FF/REW

PAUSE

STOP

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4748

MP3/WMA/JPEG Playback Operation

DVD

Operation

ROOT

TECHNO

POPS

AZZ

END

ALTZ

DD_CUB I C

CTURNE

• Select file (During STOP mode)

1)Press to select an MP3/WMA file (

➡ MP3/WMA Playback (see right)

2)Press to select a JPEG file ( ).

➡ JPEG Playback (see p. 50)

3)Press

SKIP

| (next) or |

SKIP

(previous) to skip a file/folder page (7files)

in the File area.

• Select folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

SET

to display files/folders contained

in the folder.

• Select parent folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

SET

to make changes to the previous

directory display.

• Only File (not Folder) area

operation is possible.

• Files are displayed in the

following order:

(!...0,1....9,A,B......Z).

Press

ACTION

to return to the DVD MAIN

MENU. (➛ Press

ACTION

again to return

to the MP3/WMA/JPEG MENU.)

[PLAY MODE]

NORMAL:

All MP3/WMA files are selected and

played back one time only.

SINGLE REPEAT:

The selected MP3/WMA file is played

back repeatedly.

FOLDER REPEAT:

The MP3/WMA files contained in the

selected folder are played back

repeatedly. However, folders below the

selected folder are not played back.

DISC REPEAT:

All MP3/WMA files are played back

repeatedly.

Notes

MP3/WMA Playback

■ Forward/Reverse Search

Press

FF/SLOW+

REW/SLOW-

during play.

Press

PLAY

to release.

•Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

■ Forward/Reverse Track Skip

Press

SKIP

| or |

SKIP

during play.

Each press skips a track.

•If pressed within first 3 seconds of playback,

skips to the previous track. If over 3 seconds,

returns to top of track. (|

SKIP

only.)

•Put DECK in Stop mode before performing

folder/file selection (see step 4.)

■ Pause

Press

PAUSE

during play.

Press

PLAY

to release.

Press to select an MP3/WMA file (

(During STOP mode)

Press

SET

PLAY

to start playback.

Press

OPEN/CLOSE

to eject the disc.

The MP3/WMA/JPEG MENU is closed

automatically.

Press

STOP

to stop play.

Do steps 1~3 on left.

• Copyright protected files and files

containing errors cannot be played

back. The DECK skips to the next file.

Note

■ Select PLAY MODE [MP3/WMA Playback]

(During STOP mode)

1) Press to move cursor to

PLAY MODE.

2) Press to select the desired PLAY

MODE (see below).

PLAY

PLAY MODE : NORMAL

ROOT

. .

END

ALTZ

TECHNO

CUB I C

POPS

CTURNE

AZZ

Function

Status

Counter

PLAY MODE

Folder area

File area

Parent

folder

(Current folder

appears green.)

(Selected file/

folder is

highlighted.

Titles are

displayed

up to 11

characters.)

(Diagram left shows CD directory

structure as displayed in example

OSD above.)

:MP3 file :WMA file

:Folder :Parent folder

:JPEG file

Notes

Press

POWER*

on the remote or DECK.

Press

OPEN/CLOSE

then place an MP3/WMA/JPEG disc into

the disc tray.

Press

OPEN/CLOSE

to close.

This unit can play MP3/WMA/JPEG format CD-R or

CD-RW recorded for personal use on a PC, etc.

Some discs may not play due to the condition of the

recording.

• MP3/WMA/JPEG menu is displayed.

• Playback starts automatically

(except JPEG files).

• CD directory is displayed.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4749

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

MP3/WMA/JPEG Playback Operation (continued)

JPEG Playback

Press to select an JPEG file ( ).

■ Returned on the MP3/WMA/JPEG MENU

➡ Press

STOP

. (See p. 49)

■ Next/Previous Search

➡ Press

SKIP

| or |

SKIP

■ Start Slide-show ➡ Press

FF/SLOW+

REW/SLOW-

. (below)

■ Enlarging an image ➡ Press

ZOOM

. (P. 51)

■ Rotating an image ➡ Press

ANGLE

. (P. 51)

[JPEG Playback Screen]

Do steps 1~3 on page 49.

Press

SET

PLAY

Selected JPEG file is displayed.

You can play back JPEG images.

Displayable Image Size: 32x32~7680x7680 pixels

Image changes every 3 seconds.

JPEG Slide-show

Press

FF/SLOW+

REW/SLOW-

JPEG files are displayed automatically

(about every 3 seconds) as a slide-show.

Press

ACTION

to return to the DVD MAIN

MENU.

(During JPEG Playback.)

■ Cancel slide show

➡ Press

STOP

to return to the MP3/WMA/

JPEG MENU. (See p. 49)

■ Still picture

➡ Press

STILL

(only SLIDE).

➡ Press

PLAY

to release.

■ Forward/Reverse File Skip

➡ Press

SKIP

| or |

SKIP

Each press skips a file.

REW/SLOW-

FF/SLOW+

Operation can be done when files are in

order, such as in the diagram below.

REW/SLOW-

FF/SLOW+

[PLAY MODE]

NORMAL:

All JPEG files are selected and

played back one time only.

SINGLE REPEAT:

The selected JPEG file is played back

repeatedly.

FOLDER REPEAT:

The JPEG files contained in the

selected folder are played back

repeatedly. However, folders below the

selected folder are not played back.

DISC REPEAT:

All JPEG files are played back

repeatedly.

ROOT

AAA

DDD

TTT

UUU

VVV

WWW

ZZZ

01 PIC

• Some JPEG format may not be played

back.

Note

Press

STOP

to return to the MP3/WMA/

JPEG MENU.

■ Select PLAY MODE [JPEG Slide-show]

(During STOP mode) (See p. 49)

1) Press to move cursor to

PLAY MODE.

2) Press to select the desired PLAY

MODE (see below).

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4750

DVD

Operation

You can enlarge specific portions of a JPEG picture

and select the zoom ratio using the ZOOM button

on the remote during JPEG Playback screen.

Set Zoom size.

Press

ZOOM

repeatedly to change display as

follows.

➡

Press

STOP

to return to the MP3/WMA/JPEG MENU.

• You can enlarge the center portion of the image to

one of 2 magnifications.

• Operation can be done during Rotation (below).

X 1.0 (ORIGINAL)

1st press

2nd press

3rd press

X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)

■ Use the , , and buttons to move the

position up, down, left and right.

(Position cannot be changed on X1.0

ORIGINAL images.)

JPEG Zoom

JPEG Rotation

(During JPEG Playback.)

Set rotation.

Press

ANGLE

repeatedly to change display

as below.

➡

Press

STOP

to return to the MP3/WMA/JPEG

MENU.

(During JPEG Playback.)

You can rotate a JPEG picture using the ANGLE

button on the remote during JPEG Playback

screen. (The JPEG picture will be rotated 90 °

clockwise.)

2nd press 3rd press

• Operation can be done during Zoom (above).

• The vertical/horizontal ratio of rotated JPEG

images may vary when they are displayed.

1st press

4th press

SET

FF/

SLOW+

STOP

REW/

SLOW-

PLAY

SELECT

SKIP

STILL

ACTION

ZOOM

ANGLE

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and

Thomson multimedia.

Windows Media, and the Windows logo are trademarks, or registered

trademarks of Microsoft Corporation in the United States and/or other countries.

WMA is a compression format developed by Microsoft Corporation. It achieves

the same sound quality as MP3 with a file size that is smaller than that of MP3.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4751

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

DVD Lock (DVD-Video only)

LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs, Video

CDs, WMA, MP3 and JPEG is prohibited.

(Use to prohibit play of mature theme DVDs not

encoded with rating level.)

LEVEL 1 : mature theme DVDs

LEVEL 2 : DVDs expressly for children can be played back.

LEVEL 3 to 7 : DVDs for general audiences/children can be

played back. (DVDs with mature content

are prohibited.)

LEVEL 8 : NO LIMIT: (Factory preset)

All DVDs can be played back.

You can prevent playback of DVDs of a specific

rating level which may be unsuitable for children.

• Some DVDs are encoded with a rating level. If the disc

rating is higher (stricter) than the one you preset,

playback will be prohibited.

After DVD Lock is set and a

blocked DVD is played, this

message will appear.

The message may differ

depending on the disc.

To continue viewing a blocked

program for now,

Press to select “YES” and

SET. Then, enter your 4 digit

secret code (see step 3 left).

When “NO” is selected, blocked

programs cannot be viewed.

DVD Lock Feature

SELECT:

SET : SET END : DISPLAY

YOUR SELECTION EXCEEDS THE

PLAYER S RATING LIMIT.

DO YOU WANT TO CHANGE THE

LIMIT?

YES

Discs not encoded with rating

level will play even if the jacket

states it is for mature

audiences. For these discs, the

DVD Lock Ratings will not work.

Caution

Press

to select rating level, and

press

SET

to select “LOCKED” or

“UNLOCKED.”

A 4-digit code must be entered to view a blocked

program or change rating settings.

Press

ACTION

to display DVD MAIN MENU.

Press

to select “PARENTAL LOCK,”

and

press

SET

to display.

1) Press

NUMBER keys

to enter your secret code.

2) Enter same secret code

again for confirmation.

3) Press

SET

to display.

• Step 2) not necessary when

changing rating or secret

code.

• Take care that you are not

observed entering the

secret code.

To Make Corrections

Press repeatedly to

move the cursor.

Press

NUMBER keys

make the correction.

Change your secret code

• You will need your current code.

Do steps 1 ~ 2 left.

Enter current secret code.

Press

CLEAR

to clear the code.

Do step 4 to enter new code.

• DO NOT forget your secret code.

Note

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STILL MODE : AUTO

TV MODE : 4:3 Letterbox

PARENTAL LOCK : LEVEL 8

*Important: If a remote control button does not work when

pressed, press the DVD button on the remote

and try the button again.

Ready Checklist

DECK is in DVD mode, press DVD.

ENTER

END

ACT

ENTER 4

CODE

----

PROGRAM RATING EXCEEDED

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4752

Disc Languages (DVD only)

To select and set the language of the audio

soundtrack, subtitles, or title/DVD menus for all discs

to be played.

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese

Original: Original disc language

OTHER ✱✱✱✱: Other language selection*

“SUBTITLE” selections

(Factory preset: AUTO)

To select the subtitle language.

AUTO: Same language selected

for “AUDIO”

• If language set for “AUDIO” is used in

playback, subtitles will not appear.

• If another language is used during

playback, the subtitles will appear

in the language selected at “AUDIO”

setup.

English/Spanish/French/Japanese

OTHER ✱✱✱✱: Other language selection*

“MENUS” selections

(factory preset: English)

To select the language used in title

menus or DVD menus.

English/Spanish/French/Japanese

OTHER ✱✱✱✱:

Other language selection*

To enter OTHER ✱✱✱✱

code

number,

Press

NUMBER keys

(Please refer to

language codes on page 60).

To make corrections, press

repeatedly to delete language code

number, and correct.

Settings for DVD Operation

Once initial settings are done, they

remain in memory (even after power off)

until changed. This means DECK will

operate under the same conditions

(especially DVDs) each time.

DISC LANGUAGES (See below)

All languages offered on the disc can be set.

If the language not offered is set, the original disc

language will be selected.

AUDIO OUTPUT (See p. 54.)

You can set the audio output that comes from the

digital audio output terminal.

STILL MODE (See p. 57.)

To select “FIELD” (Field still) or “FRAME” (Frame

still) to prevent jitter or make small text or fine

patterns clearly visible in a still picture. When

“AUTO” is set “FIELD” or “FRAME” is selected

automatically.

TV MODE (See p. 57.)

To select whether the video material for a wide-

screen will be played back in the Pan & Scan style,

Letterbox style or 16 : 9 style.

Press

to select

“DISC LANGUAGES,”

and

press

SET

to display screen.

Press

ACTION

to display DVD MAIN MENU.

Press

to select an item, and

press

SET

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STILL MODE :

AUTO

TV MODE : 4:3 Letterbox

PARENTAL

LOCK

LEVEL 8

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STILL MODE :

AUTO

TV MODE : 4:3 Letterbox

PARENTAL

LOCK

LEVEL 8

Press

to select an item, and

press

SET

repeatedly

for desired language.

(Please refer right.)

DISC LANGUAGES

SELECT :

SET : SET

END : ACTION

AUDIO : Engl is h

SUBTITLE : AUTO

MENUS : English

Press

ACTION

to redisplay DVD MAIN

MENU and go to step 2 to setup another

item.

Or, press

ACTION

twice to exit.

If the selected language is not offered,

the original disc language is selected.

Ready Checklist

DECK is in DVD mode, press DVD.

DVD

Operation

SET

NUMBER

keys

CLEAR

ACTION

SELECT

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4753

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

• Make settings according to amplifier

connected to optical audio output as shown

in above table.

*1 When connecting an amplifier (with an

optical digital input connector) which does

not contain the Dolby Digital or DTS

decoder, be sure to select “PCM”.

If “Bitstream” is selected, starting DVD play

may cause such a high level of noise as to

be harmful to your ears and damage the

speakers.

*2 When a DTS decoder is connected, please

select “Bitstream” in “dts”.

Audio Output

Select the digital output to be output from the optical

digital audio output connector of DECK.

■■

■ “LPCM (DVD)” selections

OFF: Linear PCM of less than 48 kHz/16 bit is

output. When playing DVDs recorded in linear

PCM of over 48 kHz/20 bit, no digital audio is

output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM of

48 kHz/20 bit/24 bit or more, digital audio

converted to 44.1 kHz/16 bit or 48 kHz/16 bit is

output.

(Digital output of PCM audio is restricted to

48 kHz/16 bit or below for copyright protection.)

■■

■ “Dolby Digital” selections

Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch) is

output. (Factory preset)

PCM: When you have connected a amplifier that

doesn’t have a built-in Dolby Digital decoder.

■■

■ “dts” selections

Bitstream: DTS bitstream is output. (Factory preset)

PCM: When you have connected a amplifier that

doesn’t have a built-in DTS decoder.

■■

■

“DRC (Dynamic Range Compression)”

selections

OFF: Normal audio range is selected. (Factory preset)

ON: For dynamic sound even at low volume, this is

useful for late-night listening. [Dolby Digital

DVDs only].

■■

■

SPEAKER SETUP

➡

See pages 55, 56, 57.

Press

to select an item,

and

press

SET

repeatedly for

output. (See below.)

Press

to select

“AUDIO OUTPUT,”

and

press

SET

to display screen.

Settings for DVD Operation (continued)

Recommended setting

LPCM

(DVD)

PCM

Dolby

Digital

PCM*

Bitstream

DTS

PCM*

PCM

Bitstream

No amplifier is connected

AV amplifier (with digital

audio input connector)

without Dolby Digital/DTS

decoder

AV amplifier including

Dolby Digital decoder

AV amplifier including

Dolby Digital/DTS decoder

Type of amplifier

to be connected

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STI LL MODE : AUTO

TV MODE : 4:3 Letterbox

PARENTAL

LOCK

LEVEL 8

AUDIO OUTPUT

SELECT :

SET : SET

END : ACTION

LPCM(DVD) : OFF

Dolby Digital : Bitstream

dts : Bitstream

DRC : OFF

SPEAKER SETUP

Press

ACTION

to redisplay DVD MAIN

MENU and go to step 2 to setup another

item.

Or, press

ACTION

twice to exit.

Press

ACTION

to display DVD MAIN MENU.

Ready Checklist

DECK is in DVD mode, press DVD.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4754

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

AUDIO OUTPUT

SELECT :

SET : SET

END : ACTION

LPCM(DVD) : OFF

Dolby Digital : Bitstream

dts : Bitstream

DRC : OFF

SPEAKER SETUP

Speaker Size Setup

Speaker frequency properties and the existence of speakers is set.

Press

to select “SPEAKER SIZE,” and press

SET

to display SPEAKER SIZE screen.

Press

to select an item, and press

SET

repeatedly. (See below table.)

DVD

Operation

SET

ACTION

SELECT

SPEAKER SETUP

SELECT :

SET : SET

END : ACTION

SPEAKER OUTPUT : MULTI-CHANNEL

SPEAKER SIZE

OUTPUT BALANCE

DELAY TIME

Menu item

FRONT

CENTER

SURROUND

SUBWOOFER

Remark

Setting

LARGE(factory preset)

SMALL

LARGE(factory preset)

SMALL

NONE

LARGE(factory preset)

SMALL

NONE

ON(factory preset)

OFF

When the front speakers (R/L) supports low-frequency (under 100 Hz) reproduction.

Select when the front speakers (R/L) does not support low-frequency reproduction.

When the surround speakers (R/L) supports low-frequency (under 100 Hz) reproduction.

Select when the surround speakers (R/L) does not support low-frequency reproduction.

When the center speaker supports low-frequency (under 100 Hz) reproduction.

Select when the center speaker does not support low-frequency reproduction.

If there is no center speaker.

If there is no surround speaker.

If there is no subwoofer speaker.

If there is a subwoofer.

SPEAKER SIZE

SELECT :

SET : SET

END : ACTION

FRONT

: LARGE

CENTER : LARGE

SURROUND : LARGE

SUBWOOFER :

Press

ACTION

four times to exit.

Speaker Output Setup

Press

to select “SPEAKER

SETUP,” and

press

SET

to display

SPEAKER SETUP

screen.

Set the number of speakers connected to the receiver

(amplifier, decoder.) (See pp. 14, 15.)

Do steps 1~3 on page 54.

Press

to select “SPEAKER

OUTPUT,”

and

press

SET

repeatedly.

(See below.)

■■

■SPEAKER OUTPUT

MULTI-CHANNEL: (Factory preset)

Use this setting when 3 or more speakers are

connected. In this case, it is necessary to set

[SPEAKER SIZE], [OUTPUT BALANCE], and

[DELAY TIME].

2-CHANNEL:

When 2 speakers are connected, it is not

necessary to set [SPEAKER SIZE], [OUTPUT

BALANCE], and [DELAY TIME] (these setting

menu are not displayed.)

Press

ACTION

three times to exit.

**If SUBWOOFER is set to “OFF,”

the front speakers are set to

“LARGE” automatically.

Do steps 1~2 of “Speaker Output Setup” above.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4755

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Output Balance Setup

Adjust the volume level output from the speakers. To adjust, play a disc or set the “TEST SIGNAL”

(p.57) to ON. Then adjust while confirming the volume. (Even if “OFF” or "NONE" is set in “SPEAKER

SIZE,” the speaker OUTPUT BALANCE can still be set.)

Settings for DVD Operation (continued)

Delay Time Setup

To enjoy 5.1 CH sound, it is ideal to place all

speakers, except the subwoofer, in a circular

arrangement. (See <Speaker Position> p. 57.)

If this is not possible, setting Delay Time gives the

sound output a delayed effect which gives you the

illusion of the ideal listening position. (See right.)

Press

ACTION

three times to exit.

Press

to select “OUTPUT BALANCE,” and press

SET

to display OUTPUT BALANCE screen.

Press

to select an item, and press

SET

repeatedly.

(See below table.)

Press

to select “DELAY TIME,” and press

SET

to display DELAY TIME screen.

Press

to select an item, and press

SET

repeatedly. (See below.)

OUTPUT BALANCE

SELECT :

SET : SET

END : ACTION

CENTER

: 0dB

SURROUND(R) : 0dB

SURROUND(L) : 0dB

SUBWOOFER : 0dB

TEST SIGNAL : OFF

Menu item

SURROUND

CENTER

Remark

Setting

0ms 1ms 2ms 3ms 4ms 5ms

0ms(Factory preset)

Setting a delay effect.

0ms 5ms 10ms 15ms 20ms

Distance

Setting

Approx. 50 cm (1 feet)

Approx. 100 cm (3 feet)

1.3 ms

2.6 ms

3.9 ms

5.3 ms

Approx. 150 cm (5 feet)

Approx. 200 cm (6 feet)

Distance

Setting

Approx. 200 cm (6 feet)

Approx. 400 cm (12 feet)

5.3 ms

10.6 ms

15.9 ms

Approx. 600 cm (18 feet)

Center speaker

Surround speaker

• , : Delay time as 0ms

(Factory prest)

• , < : Find the distance

in the

table (below) and change to

the recommended setting.

[See <Speaker Position> p.57.]

Press

ACTION

four times to exit.

Menu item

SUBWOOFER

SURROUND(L)

SURROUND(R)

CENTER

Remark

Setting

-6dB

+6dB

0dB(factory preset)

Adjust so that the center speaker volume is virtually the same

level (-6dB ~ +6dB) as the front speakers.

Adjust so that the surround speaker(R) volume is virtually

the same level (-6dB ~ +6dB) as the front speakers.

Adjust so that the surround speaker(L) volume is virtually

the same level (-6dB ~ +6dB) as the front speakers.

Adjust so that the subwoofer speaker volume is optimum.

However, because no test sound will come from the

subwoofer, play a disc to confirm, then adjust.

TEST SIGNAL : Switch test signal used for OUTPUT BALANCE setting to “OFF” or “FRONT(L)”....

➡ See page 57.

Do steps 1~2 of “Speaker Output Setup” on page 55.

Do steps 1~2 of “Speaker Output

Setup” on page 55.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4756

Press to select “TV

MODE,” and press

SET

repeatedly for

mode.

(See below.)

4:3 Pan & Scan (Factory preset) :

Wide-screen video data is played in

Pan & Scan style (left and right of screen

is trimmed.)

•Video data not formatted in Pan & Scan

will play in letterbox style.

4:3 Letterbox :

Wide-screen video data is played in

Letterbox style (top and bottom of screen

has black margin).

16:9 :

Set “16:9” when using Wide-screen TV.

Press

ACTION

to exit this mode.

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

[Letterbox]

TV Mode

Example

DVD

Operation

[Pan & Scan (Factory preset)]

Test Signal Setup

This feature assists in the setting of

OUTPUT BALANCE. Starting with (L) front

speaker, a test sound is output in clockwise

order. While the test signal is output, adjust

the output of the center speaker and

Surround speaker (R/L).

(See “OUTPUT BALANCE.” P. 56.)

Press

to select “TEST

SIGNAL,” and

press

SET

(See below.)

Press

ACTION

four times to exit.

No sound will come from the subwoofer.

Adjust as desired when playing a disc.

While the TEST SIGNAL is output, if the

setting change in the OUTPUT BALANCE (p.

56) is under 2 seconds, the output will switch

to the next speaker. The speaker name from

which the TEST SIGNAL is currently being

output is displayed.

(Example; "TEST SIGNAL : CENTER")

OUTPUT BALANCE

SELECT :

SET : SET

END : ACTION

CENTER : 0dB

SURROUND(R) : 0dB

SURROUND(L) : 0dB

SUBWOOFER : 0dB

TEST SIGNAL

: OFF

Still Mode

Press

to select “STILL MODE,”

and

press

SET

repeatedly

for mode. (See below.)

AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is

automatically selected during the still mode.

(Factory preset)

FIELD: “FIELD” (Field still) is always selected.

This setting will reduce jitter when compared

with “AUTO” on some discs.

FRAME:“FRAME” (Frame still) is always selected.

Some texts and fine patterns will be seen clearly

when compared with “AUTO” on some discs.

TV Mode

Set the screen display style for wide-screen video

material playback.

Set to reduce jitter in a displayed still picture or a motion

picture.

Press

ACTION

to exit this mode.

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STI

MODE

: AUTO

TV MODE : 4 :3 L et t er b ox

PARENTAL

LOCK

LEVEL 8

Press

ACTION

to display DVD MAIN MENU.

Press

ACTION

to display DVD MAIN MENU.

CENTER

FRONT(R)

SUBWOOFER

FRONT(L)

Listening

position

SURROUND(R)

SURROUND(L)

FRONT(L) CENTER FRONT(R)OFF

SURROUND(L) SURROUND(R)

2sec 2sec

2sec

DVD MAIN MENU

SELECT :

SET : SET

END : ACTION

DISC LANGUAGES

AUDIO OUTPUT

STI LL MODE : AUTO

TV MODE : 4:3 L et t er b ox

PARENTAL

LOCK

LEVEL 8

Do steps 1~2 of “Output

Balance Setup” on page 56.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4757

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

TIMER REC

SELECT : SET : SET

EXIT : ACTION PAGE : SKIP

SINGLE

SLIDE

SD Card

JPEG Playback

Still image data (JPEG) made with a digital camera, digital video camera, or PC can be played back

using an SD Memory Card/MultiMediaCard.

Compatible Card : An SD Memory Card and MultiMediaCard can be used in this DECK.

Displayable Image Formats : DCF format 1.1 compliant

Baseline JPEG format Y Cb Cr (compressed format)

(Sampling ratios 4:4:4, 4:2:0, 4:2:2, 4:1:1)

(80 x 60 ~ 5120 x 3840 pixels)

Exif2.1 image data contained in [IMEXPORT] folder used for data

transfer bitween the equipment with SD Memory Card.

• JPEG files altered and saved on a PC as “grayscale” format cannot be displayed.

• Some parts of an image may not be displayed or the image may be displayed on a

smaller scale depending on the size of the image.

Notes

Insert the SD Card.

SD MENU is displayed

automatically. If SD

MENU is not displayed,

reinsert the SD Card.

<If in VCR mode with SD

card already inserted.>

Press ACTION.

Press

to select “SD CARD

PLAYBACK.”

Press SET

to display.

• During Timer REC, the above menu

is not displayed. To display the SD

Menu, reinsert the SD Card.

Note

SELECT :

EXIT

: ACTION

SET:SET

SET UP VCR

SET CLOCK

SET UP CHANNEL

SD CARD PLAYBACK

IDIOMA/LANGUE : ENGLISH

VCR’S OUTPUT CH:3

“SD” appears when in SD mode.

Multi Function Display

INDEX AREA

This area is used to

display the files stored

within the SD Card.

■ Return to VCR Mode,

➡ Press ACTION.

SD MENU DISPLAY

■ SINGLE PLAY

A single image, selected from the index area, can be enlarged and played back. Also, functions,

such as zoom, rotation and applying image information can be performed.

➡ See “SINGLE PLAY mode” on page 59.

■ SLIDE SHOW

A slide show presentation can be composed, including various image transition effects and

transition speeds.

➡ See “SLIDE SHOW mode” on page 59.

SINGLE PLAY

SLIDE SHOW

DISPLAY

PAGE No.

• Up to 1000 files can be

displayed.

Note

•“SD” blinks while data is being read.

Note

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4758

DVD

Operation

DVD

Operation

SINGLE PLAY mode

Press to select

“SINGLE,” and press SET.

Press

to move

cursor to desired file in

INDEX AREA.

(Press SKIP +/

to display

next/previous page of 9

thumbnail files),

Press SET to display file in

large size.

Press SKIP+

➡ next image.

Press SKIP-

➡ previous image.

■ZOOM (Enlarge Image)

Image can be displayed 2 or 4 times normal size.

➡ Press ZOOM repeatedly.

■ROTATE

Image can be rotated clockwise in 90° increments.

➡ Press ANGLE repeatedly.

■Start Slide-show ➡ Press PLAY. (See below.)

■Display file information screen ➡ Press DISPLAY.

Do steps 1 - 2 on p. 58.

Press ACTION

to exit this mode.

SELECT : SET : SET

END : ACTION PAGE : SKIP

SINGLE

SLIDE SHOW mode

Do steps 1 - 2 on p. 58.

Press to select

“SLIDE,” and press SET.

Press

to move

cursor to desired file in

INDEX AREA.

(Press SKIP +/

to display

next/previous page of 9

thumbnail files).

Press SET to display

SLIDE MENU.

Press

to select an

item (see right), and press

SET repeatedly to set.

START SLIDE SHOW.

Press ACTION

to exit this mode.

■PAUSE

Press PAUSE. ➡ Press PLAY to relese.

■Press SET to return SLIDE MENU (above).

SLIDE MENU

SELECT : SET : SET

END : ACTION

START

SPEED : FAST 2S

TRANSITION : NORMAL

...

• Once selected, image is displayed

in about 3 sec. (“ ” appears while

data is read. DO NOT remove SD

Card during data reading.)

• Deck buttons are inoperative.

Use remote control.

• If cursor is at top of the INDEX

AREA, pressing “ ” selects previous

page. If cursor is at bottom of the

INDEX AREA, pressing “ ” selects

next page.

• If Rotate is operated while Zoom (X2

or X4) is displayed, the unit will revert

to X1 (ORIGINAL) magnification.

Notes

X 1.0 (ORIGINAL)

1st press

2nd press

3rd press

X 2 (ZOOM 1) X 4 (ZOOM 2)

F I LE : 12345

DATA : 05/16/2003

SIZE : 500KBYTE

PIXEL : 640✕480

ZOOM : NORMAL

ROTATE: 0

NEXT : SKIP+

ZOOM : ZOOM

SLIDE : PLAY

PREV : SKIP-

ROTATE

: ANGLE

END : ACTION

File information screen

[START]

Starts slide show.

[SPEED]

FAST:

Image transition every

2 seconds.

MEDIUM:

Image transition every

5 seconds.

SLOW:

Image transition every

10 seconds.

[Transition]

NORMAL:

Image transition one by one.

WIPE:

Image transition from top to bottom.

SPLIT:

Image transition beginning at the center

and splitting to the left and right.

BLIND:

Image transition in a series of band-like

shapes that resemble window blinds.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4759

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or

“MENUS” (see p. 53).

Code Language

7079 Faroese

7082 French

7089 Frisian

7165 Irish

7168 Scots Gaelic

7176 Galician

7178 Guarani

7185 Gujarati

7265 Hausa

7273 Hindi

7282 Croatian

7285 Hungarian

7289 Armenian

7365 Interlingua

7378 Indonesian

7383 Icelandic

7384 Italian

7387 Hebrew

7465 Japanese

7473 Yiddish

7487 Javanese

7565 Georgian

7575 Kazakh

7576 Greenlandic

7577 Cambodian

7578 Kannada

7579 Korean

7583 Kashmiri

7585 Kurdish

7589 Kirghiz

7665 Latin

Code Language

7678 Lingala

7679 Laothian

7684 Lithuanian

7686

Latvian, Lettish

7771 Malagasy

7773 Maori

7775 Macedonian

7776 Malayalam

7778 Mongolian

7779 Moldavian

7782 Marathi

7783 Malay

7784 Maltese

7789 Burmese

7865 Nauru

7869 Nepali

7876 Dutch

7879 Norwegian

7982 Oriya

8065 Panjabi

8076 Polish

8083

Pashto, Pushto

8084 Portuguese

8185 Quechua

8277

Rhaeto-Romance

8279 Romanian

8285 Russian

8365 Sanskrit

8368 Sindhi

8372

Serbo-Croatian

8373 Singhalese

Code Language

8375 Slovak

8376 Slovenian

8377 Samoan

8378 Shona

8379 Somali

8381 Albanian

8382 Serbian

8385 Sundanese

8386 Swedish

8387 Swahili

8465 Tamil

8469 Telugu

8471 Tajik

8472 Thai

8473 Tigrinya

8475 Turkmen

8476 Tagalog

8479 Tonga

8482 Turkish

8484 Tatar

8487 Twi

8575 Ukrainian

8582 Urdu

8590 Uzbek

8673 Vietnamese

8679 Volapük

8779 Wolof

8872 Xhosa

8979 Yoruba

9072 Chinese

9085 Zulu

Code Language

6565 Afar

6566 Abkhazian

6570 Afrikaans

6577 Ameharic

6582 Arabic

6583 Assamese

6588 Aymara

6590 Azerbaijani

6665 Bashkir

6669 Byelorussian

6671 Bulgarian

6672 Bihari

6678

Bengali; Bangla

6679 Tibetan

6682 Breton

6765 Catalan

6779 Corsican

6783 Czech

6789 Welsh

6865 Danish

6869 German

6890 Bhutani

6976 Greek

6978 English

6979 Esperanto

6983 Spanish

6984 Estonian

6985 Basque

7065 Persian

7073 Finnish

7074 Fiji

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4760

These displays will alert you to a missed operation or provide further instructions.

Warning and Instruction Displays

PLEASE SET CLOCK BY

PRESSING ACTION KEY

CHECK CASSETTE

RECORD TAB

NO CASSETTE

VIDEO HEADS MAY NEED

CLEANING PLEASE INSERT

HEAD CLEANING CASSETTE

OR REFER TO MANUAL

END : PLAY

VCR LOCK ACTIVATED

Page

CautionOSD

If you attempt to set or review a Timer

Recording and the Clock is not set...

REMOTE CONTROL IS SET

TO TV MODE

USE VCR : VCR KEY

USE DVD : DVD KEY

REMOTE CONTROL IS SET

TO CABLE/DSS MODE

USE VCR : VCR KEY

USE DVD : DVD KEY

PLEASE PREPARE FOR TIMER

REC

PLEASE CHECK THE DISC,

AND FOR STAINS OR

SCRATCHES ON DISC

IT IS PROHIBITED TO COPY

DVD/VIDEO CD/CD TO VHS

TO CANCEL TIMER REC

HOLD DOWN STOP KEY

FOR APPROX 3 SEC

For Your

Information

THIS DISC MAY NOT BE PLAYED

IN YOUR REGION

THIS TYPE OF DISC CANNOT BE

PLAYED. PLEASE INSERT A

DIFFERENT DISC

CANNOT PLAY THIS FILE

DATA ERROR

CARD ERROR

If DECK is not in Stop mode or a cassette with

record tab is not inserted 2 minutes before a

Timer Recording is about to begin...

If you press REC on the remote control or DECK,

and a cassette is inserted with no record tab...

If you press PLAY, FF, REW, or REC on the

remote control or DECK without a cassette

inserted...

If you press STOP or POWER during a Timer

Recording...

(visible in VCR mode only)

If head cleaning becomes necessary while

playing back a tape...

If you press a function button other than STOP/

EJECT or POWER while DECK is

in VCR Lock mode...

If you press an invalid key on the remote while

in CABLE/DSS mode...

If you press an invalid key on the remote while

in TV mode...

If you press PLAY, and DECK reads data from a

stained or scratched disc in DVD mode.

Playback of a disc with different region number

was attempted. Only discs marked region “1”,

“ALL”, or those that include “1” are playable on

this DECK.

An unusable disc is inserted in the DECK.

This file format cannot be played.

(Appears during MP3/WMA/JPEG file playback)

THIS FILE IS PROTECTED

This file is copyright protected and cannot be

played back. (Playback is prohibited.)

(WMA only)

If you press REC in DVD mode...

An image file could not be displayed. The file is

corrupt or the format is incompatible.

SD Memory Cards that have been formatted to

FAT32 specifications cannot be used.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4761

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Before Requesting Service

Power

No power…

Power turns itself off...

Recording & Playback

TV program cannot be recorded...

Timer recording cannot be

performed…

There is no playback picture, or the

playback picture is noisy or contains

streaks...

During special effects playback,

picture may contain some vertical

jitter when using a TV with an

Automatic Vertical Hold Control...

DECK cannot be controlled...

Check the following points if you are having trouble with your DECK.

Correction

• Completely insert Power Plug into an AC outlet.

• Set POWER button to on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min.

in DVD mode with no operation, or if there is no

broadcast signal in TV or Playback mode.

Turn the power back on. (pp. 23, 33)

Correction

• Check connections between DECK, external

antenna, and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is

correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and

tuned to channel to be recorded.

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued

if a power interruption occurs before or during a

Timer Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output

channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

• Adjust TRACKING control in either direction. (p. 4)

• Try Head Cleaning. (p. 4)

• Set TV’s Vertical Hold Control to MANUAL, then

adjust.

• Make sure DECK power is on.

• Check Remote batteries.

• Make sure VCR LOCK is set to off. (p. 33)

• Make sure Remote is in proper mode. (p. 28)

• Make sure Timer Recording is not in progress.

Remote Control

DECK cannot be remote controlled...

PROG buttons do not respond...

Correction

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p.9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent

or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT

Video Output and S-VIDEO OUT. Set TV to either RF

IN or VIDEO IN. (p. 10)

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4762

Check the following points if you are having trouble with your DECK.

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Video cassette ejects when

a recording is started or the power is

turned off for timer recording...

In Stop mode, the motor (CYLINDER)

continues to rotate...

The disc cannot be removed..

Correction

• Make sure TV is set to output of DECK.

• Check connections between DECK,

external antenna, and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• Insert the cassette with window side up; record

tab facing you.

• Make sure cassette record tab is intact. (p. 6)

• To enable Quick play mechanism, the cylinder will

rotate for about 3 minutes. This reduces response

time from Stop to Play mode.

• First, unplug DECK. Then, prepare a rigid wire

(e.g. an extended paper clip) and, applying

moderate force, insert it straight into the hole at the

base of the tray. The tray will eject a little. Now, pull

the tray all the way out and remove the disc. (p. 9)

DVD/ Video CD/ CD

Play fails to start even when PLAY is

pressed...

Play starts but then stops immediately...

Picture is distorted during rapid

advance or rapid reverse...

No Forward/Reverse Scene Search

play...

Play does not start even when title is

selected...

Audio soundtrack and/or subtitle

language is not the one selected at

the initial settings...

No subtitles...

Alternative audio soundtrack

(or subtitle) language cannot be

selected...

Angle cannot be changed...

Correction

• This DECK cannot play discs other than DVDs,

Video CDs and CDs.

• The disc may be dirty and require cleaning.

• Be sure disc is installed with label side up.

• The picture will be somewhat distorted at times:

this is normal.

• Some discs may have sections which prohibit

Forward/Reverse Scene Search. (p. 23)

• Confirm the “DVD LOCK” setting. (p. 52)

• If the audio soundtrack and/or subtitle language

selected at DVD initial settings does not exist

on the disc, it will not be accessible.

• Subtitles appear only when available on disc.

•“OFF” is selected at the changing subtitle

language. Select “ON” at the “Subtitle Languages”

section (p. 36) to display the subtitles.

• Alternative language cannot be selected with discs

which do not contain more than one language.

• For some discs, alternative language cannot be

selected with the AUDIO or SUB TITLE button.

Try selecting it from the DVD MAIN MENU if available.

• This function is dependent on software availability.

Even if disc has multiple angles, they may be

recorded for specific scenes only (ANGLE

indicator on DECK lights up). (p. 37)

If you cannot resolve the problem, please call the Customer Call Center for product

assistance at 1-800-211-PANA (7262).

To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).

or send e-mail to : [email protected]

For Your

Information

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4763

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Limited Warranty

PANASONIC CONSUMER ELECTRONICS COMPANY,

DIVISION OF MATSUSHITA ELECTRIC

CORPORATION OF AMERICA

One Panasonic Way

Secaucus, New Jersey 07094

PANASONIC SALES COMPANY,

DIVISION OF MATSUSHITA

ELECTRIC OF PUERTO RICO, INC.,

AVE. 65 de Infantería, Km. 9.5

San Gabriel Industrial Park

Carolina, Puerto Rico 00985

Panasonic DVD/VCR Deck Limited Warranty

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or workmanship, Panasonic

Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)

will, for the length of the period indicated on the chart below, which starts with the date of original purchase

(“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b)

replace it with a new or a refurbished product. The decision to repair or replace will be made by the

warrantor.

During the “Labor” Limited Warranty period there will be no charge for labor. During the “Parts” warranty

period, there will be no charge for parts. You must mail-in your product during the warranty period.

If non-rechargeable batteries are included, they are not warranted. This Limited Warranty only applies to

products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended

only to the original purchaser and only covers product purchased as new. A purchase receipt or other

proof of original purchase date is required for Limited Warranty service.

Mail-In Service

For assistance in the continental U.S.A. in obtaining repairs please ship the product to:

Panasonic Services Company

Customer Servicenter

Suite B

4900 George McVay Drive

McAllen, TX 78503

For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.

When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original

carton. Include a letter detailing the complaint and provide a day time phone number where you can be

reached.

IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE PURCHASER WILL BE

REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF

PURCHASE, AMOUNT PAID AND PLACE OF PURCHSE. CUSTOMER WILL BE CHARGED FOR THE

REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.

Product or Part Name

DVD/VCR Deck

Rechargeable Batteries

(in exchange for defective item)

Labor

Ninety (90) Days

Not Applicable

Parts

One (1) Year

Ten (10) Days

D4763S P36-60 (030610 –§”Ô•Ï•X2nd).p65 2003/06/10, 18:5964

For Your

Information

Limited Warranty Limits And Exclusions

This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES

NOT COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT

COVER damages which occurred in shipment, or failures which are caused by products not supplied

by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling,

misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls,

improper maintenance, power line surge, lightning damage, modification, or commercial use (such as

hotel, office, restaurant, or other business), rental use of the product, or service by anyone other than

a Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY

COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY

BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having

someone remove or re-install an installed unit if applicable, travel to and from the servicer, loss of or

damage to media or images, data or other recorded content. The items listed are not exclusive, but

are for illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF

MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or

limitations on how long an implied Limited Warranty lasts, so the exclusions may not apply to you.

This Limited Warranty gives you specific legal rights and you may also have other rights which vary

from state to state. If a problem with this product develops during or after the Limited Warranty period,

you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then

write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR

RESPONSIBILITY.

Customer Services DirectoryCustomer Services Directory

For Product Information, Operating Assistance, Literature Request, Dealer Locations, and

Customer Service inquiries please visit Web Site:

http://www.panasonic.com

You can purchase parts, accessories, locate your nearest servicenter and more by visiting our Web Site

or E-mail us via web:

http://www.panasonic.com/consumer_electronics/support/customerfeedback.asp

Contact:

1-800-211-PANA (7262),

Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.

Service in Puerto Rico

Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

1-800-332-5368 (Customer Orders Only)

1-800-237-9080 (Fax Only)

(Monday-Friday 9 am-8 pm, EST.) Panasonic Services Company

20421 84th Avenue South, Kent, WA 98032

(Accepts Visa, MasterCard, Discover Card, American Express, and Personal Check)

http://www.pasc.panasonic.com or email to [email protected]

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

As of May 2003

Accessory Purchases

For hearing or speech impaired TTY users, TTY : 1-866-605-1277

Customer Services Directory

D4763S P36-60 (030610 –§”Ô•Ï•X2nd).p65 2003/06/10, 18:5965

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Spanish Quick Use Guide/ Guía para rápida consulta

Para ajustar el idioma, canal yPara ajustar el idioma, canal y

CONEXIONES/CONFIGURACION INICIAL (READY TO PLAY)

Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.

EL DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.

CONEXIONES

Conecte el cable de la antena al terminal IN

FROM ANT del DVD/VCR.

Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con

el cable RF incluido.

Para Ant/Cable

➛➛

➛ DVD/VCR

➛➛

➛ TV

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable

➛➛

➛ DVD/VCR

➛➛

➛ TV

Conecte la salida de convertidor de cable

al terminal IN FROM ANT.

Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con

el cable RF incluido.

CONFIGURACION INICIAL

Encienda el TV y cambie al canal 3.

Enchufe el cable de CA.

El DVD/VCR se encenderá e iniciará las

fijaciones de los canales y del reloj.

• Si no aparece la pantalla de abajo, compruebe

la conexión del DVD/VCR-TV y si el canal del

TV está a 3, intennte cambiando al canal 4.

• Para cambiar el canal de salida del DVD/VCR,

consulte las instrucciones de “Canal de salida

del VCR” (informaciones en inglés página 19).

Enchufe el cable de CA.

DVD/VCR

VHF/UHF

Estuche convertidor

de TV por cable

Televisor

Terminal

IN FROM ANT.

Entrada (IN) desde

ANT./CABLE

Terminal

OUT TO TV

Terminal IN FROM ANT.

Televisor

DVD/VCR

VHF/UHF

Terminal

OUT TO TV

Entrada (IN) desde

ANT./CABLE

Si está usanndo un convertidor de TV por cable y

en su area hay un canal de Public Broadcast

Station (PBS), ajuste su convertidor al canal PBS

de su area. Si está usando un receptor DSS, este

debe estar apagado.

AJUSTE MANUAL DEL RELOJ

Si la fijación ha sido incompleta.

Presione la tecla ACTION en el control remoto

para visualizar la pantalla del menú SET

CLOCK.

Presione para seleccionar el mes y SET

para ajustar. De la misma forma, seleccione y

ajuste la fecha, año, hora y DST (hora de

verano).

Presione dos veces la tecla ACTION para

poner el RELOJ en marcha y salir.

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]

Al inicio, el idioma de la

pantalla está fijado a

inglés.

Para cambiar el idioma,

seleccione la pantalla

MENU (informaciones en

inglés página 18).

AUTO CLOCK SET

PROCEEDING

CANCEL : STOP

CH AUTO SET PROCEEDING

CANCEL : STOP

PRECAUCIÓN

Al usar cables coaxiales RF del tipo “tuerca”,

apriételos solamente con los dedos. Un apriete

excesivo puede dañar los terminales.

Nota

• Los botones de funciones no funcionan durante

la configuración inicial.

• Para retirar un cassette durante el ajuste

automático, presione EJECT en el control remoto

o STOP dos veces en el aparato. En este caso,

los ajustes de los canales y la hora se deben

hacer manualmente. Para los ajustes seleccione

la pantalla MENU (informaciones en inglés

página 18).

• Dependiendo de las condiciones, el ajuste

automático puede durar más de 30 minutos.

En ese caso, presione STOP para detener el

ajuste automático y realice los ajustes

manualmente en la pantalla MENU.

2003

SUN

SET

DST

SESE

/ /

SELE

SET

EXIT

ACT

SET

Las fijaciones se realizan automáticamente.

Cuando termina las fijaciones, aparecerá la

siguiente pantalla.

Si aparece en la pantalla “AUTO CLOCK SET IS

INCOMPLETE (FIJACION AUTOMATICA DEL

RELOJ ES INCOMPLETO)”, Ajuste el reloj

como se describe a continuación.

AUTO CLOCK SET IS

PLETE

PLEASE SET CLOCK BY

PRESSING

ACT

ON KEY

SUN

20P

SETT

: CH

AUTO CLOCK SET

PLETED

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4766

Operaciones básicas para la reproducción

Inserte un cassette,

• La alimentación del DECK se activa.

En la Pantalla de Visualización Multi

Función se ilumina “VCR”.

Presione PLAY para reproducir el cassette.

• Si el cassette no tiene la lengüeta de

prevención de grabación (página 6), se

inicia la reproducción automáticamente.

Detalles especiales durante la grabación

Presione FF/SLOW+ o REW/SLOW- para

búsqueda de escenas hacia delante/ hacia

atrás. Presione PLAY para liberar. Durante

la búsqueda, cada vez que presione FF/

SLOW+ o REW/SLOW- se cambia la

velocidad como sigue:

[SLP] aprox. 21X

↔↔

↔ aprox. 9X

[LP] aprox. 9X

↔↔

↔ aprox. 7X

[SP] aprox. 7X

↔↔

↔ aprox. 3X

Si la imágen se interrumpe con la velocidad de

21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x.

Presione PAUSE/STILL para imagen Fija

(Congelada).

Presione PLAY para liberar.

Presione PAUSE/STILL en el modo de

imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar.

Presione FF/SLOW+ o REW/SLOW- en el

modo de imagen fija para cambiar la

velocidad de las imágenes a cámara lenta.

Presione STOP para detener el cassette.

Presione REW/SLOW- o FF/SLOW+ en el

modo de parada para rebobinado/avance

rápido del cassette.

Presione EJECT en el control remoto,

o STOP/EJECT en el DECK para expulsar

el cassette.

Operaciones básicas para la grabación

Inserte el cassette con lengüeta de

protección de grabación (página 6).

Presione CH / , o las teclas de números

para seleccionar el canal.

Presione SPEED para seleccionar la

velocidad de grabación (página 6).

Presione REC para comenzar a grabar.

• Para eliminar escenas indeseadas, presione

PAUSE/STILL para hacer una pausa, y al

presionar nuevamente continua la grabación.

• No podrá ver otro canal durante la

grabación.

Presione STOP para detener la grabación.

• SP = Reproducción estándar,

• LP = Larga duración,

• SLP = Superlarga duración.

Grabación de un toque

Presione REC repetidamente para ajustar la

hora de grabación (30 min - 4 horas).

• La videograbadora termina la grabación

a una hora programada.

Grabación normal

0:30 1:00

1:302:003:004:00

Programación fácil para la

grabación con temporizador

Presione PROG

para visualizar la pantalla de Programacion.

1) Para ajustar la FECHA de

grabación, presione

para seleccionar:

1-31 = una vez, o

DIARIO = a la misma hora

de lunes a viernes, o

SEMANA = a la misma

hora cada semana y

presione SET para ajustar.

2) Para ajustar los ítems que quedan,

presione para seleccionar y presione

SET para ajustar los tiempos de INICIO/

PARADA, CANAL, o entrada de LINEA (página

35), y velocidad del cassette (SP, LP, SLP).

Presione PROG para finalizar PROGRAM.

Presione

para seleccionar un número

que no está usando para

ingresar mas programas y

presione SET

para ajustar.

Luego repita el paso 2.

Presione nuevamente

PROG para salir.

Fecha de hoy

Orden para elegir

Ejemplo

FECHA

PARADA

SAB

--:--

HOY

ELEGIR

FIJAR

SET

TERMINAR

PROG

SLP

ELEGIR FECHA DE I

DIARIO

68 9

/ Orden para elegir

SEMANAL

(

SAB

)

SEMANAL

(

LUN

)

SEMANAL

(

DOM

)

ELAR

DLT

ELEGIR 1- 8 :

ENTRAR

: SET

SAL

PROG

PARADA

VEL

2 : 00

02 SLP

Guía para rápida

consulta

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4767

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Presione para seleccionar el ajuste

deseado.

Presione

SET

para ajustar.

Para volver a la pantalla normal,

Presione repetidamente

CLEAR

DISPLAY

Funcionnamiento del DVD utilizando

visualizaciones en pantalla

Presione

DISPLAY

en el modo reproducción

o parada para visualizar las visualizaciones en

pantalla.

• Cada vez que se presione

DISPLAY

,la

visualización en pantalla cambia como se

muestra a continuación.

Presione (o ) para seleccionar el ítem

deseado.

Presione

SET

para ajustar.

Spanish Quick Use Guide/ Guía para rápida consulta

■Para buscar una escena particular

Búsqueda hacia adelante

Presione

FF/SLOW+

en el modo de reproducción.

Búsqueda hacia atrás

Presione

REW/SLOW-

en el modo de reproducción.

(Para liberar, presione

PLAY

)

■Para saltar un capítulo o una pista

Salto hacia adelante

Presione

SKIP

l en el modo de reproducción.

Un capítulo (Vídeo DVD) o una pista (Audio

DVD/Vídeo CD/CD) se salta cada ves que se

oprime la tecla.

Salto hacia atrás

Presione l

SKIP

en el modo de reproducción.

■■

■Para ver una imagen fija

Presione

PAUSE/STILL

durante la reproducción.

(Para liberar, presione

PLAY

)

■Para ver imágenes cuadro a cuadro

(DVD/Vídeo CD)

Presione

PAUSE/STILL

en el modo de imagen fija.

La imagen avanza un cuadro cada vez que

presiona la tecla. (Para volver a la

reproducción normal, presione

PLAY

)

■Para ver en cámara lenta (DVD/Vídeo CD)

Presione

FF/SLOW+

REW/SLOW-

en el modo

de imagen fija.

(Para liberar, presione

PLAY

)

Operaciones básicas del DVD

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]

Presione

POWER

en el control remoto o el

aparato.

Presione

DVD

para seleccionar el modo DVD.

1) Presione

OPEN/CLOSE

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus

superficies, póngalo con el lado donde esté

impreso el título hacia arriba, alinéelo con las

guías y póngalo en su posición apropiada.

Disco de 3” (8 cm) / Disco de 5” (12 cm)

Presione

PLAY

para iniciar la reproducción.

La bandeja del disco se cierra

automáticamente.

• Si está usando un DVD interactivo (Interactive

DVD) o un Vídeo CD con contol de

reproducción (playback control) y aparece un

menú de títulos (TITLE MENU) en la pantalla,

siga al paso 5.

Presione o las teclas numéricas para

seleccionar el artículo deseado.

Presione

SET

PLAY

para la reproducción.

Si usa las teclas numéricas, la

reproducción comienza automáticamente.

Presione

STOP

para parar la reproducción.

Presione

OPEN/CLOSE

para expulsar el disco.

Cuando se presiona DISPLAY, la visualización en

pantalla muestra la información del disco (título / capítulo

/ número de lista, tiempo transcurrido de reproducción,

audio / idioma del subtítulo, y ángulo) e información

(repetir la reproducción, modo reproducción, Karaoke

vocal encendido / apagado, etc.).

Información seleccionada del disco

Información seleccionada del DECK

Pantalla normal

➡

GRUPO

: 1 DVD-AUDIO

P I STA

: 1 00:12:34

ELEGIR:

FIJAR : SET

TERMINAR

:DISPLAY

GRUPO

: 1 DVD-AUDIO

P I STA

: 1 00:12:34

ENTRAR: 0

FIJAR : SET

TERMINAR

:DISPLAY

ELEGIR:

FIJAR : SET SIGUIENTE: DISPLAY

TITULO : 12 DVD

CAPITULO:11 00:12:34

ELEGIR:

FIJAR : SET SIGUIENTE: DISPLAY

TITULO : 12 DVD

CAPITULO: 24 00:12:34

PISTA : 12 VIDEO CD

PBC : INACTIVO 00:12: 34

FIJAR : SET SIGUIENTE: DISPLAY

PISTA : 17 VIDEO CD

PBC : INACTIVO 00:12: 34

FIJAR : SET SIGUIENTE: DISPLAY

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4768

Cambio del idioma de subtítulos

[Vídeo DVD solamente]

EI idioma de los subtítulos seleccionado al hacer las

fijaciones iniciales se puede cambiar por otro idioma

diferente, si éste se encuentra disponible.

Presione

SUBTITLE

durante

la reproducción.

Cuando no haya subtítulos

grabados, se visualizará “-” en

lugar del número de idioma.

Presione para

seleccionar el idioma deseado.

Presione para

seleccionar “ACTIVO” o

“INACTIVO.”

Selección de IDIOMAS DEL

DISCO [DVD solamente]

Presione para seleccionar el artículo deseado.

Presione

SET

IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco pueden ser

ajustados. Si el idioma ajustado no es ofrecido en el

disco, se seleccionará el idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio procedente del

terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO” o “CUADRO fijo” para prevenir

inestabilidad o para permitir ver textos pequeños o

patrones finos claramente en el modo de imagen fija.

TV PREFERENCIA

Para seleccionar cuando el material del vídeo es para

pantalla ancha y se quiere reproducir en el estilo

Pan&Scan, en el estilo Letterbox o en el estilo 16:9 en

la pantalla.

Volver a visualizar el menú de DVD para

continuar el ajuste.

Presione

ACTION

y pase al paso 3 para ajustar otro

ajuste o, para salir, presione

ACTION

tres veces.

Presione DVD para seleccionar el modo DVD.

Presione ACTION en el modo de parada para

visualizar MENU.

Presione para seleccionar el artículo deseado.

Presione

SET

Seleccione “AUDIO”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa :

Original : Se seleccionará el idioma

original de cada disco.

OTRO

✱✱✱✱

:Se puede seleccionar el otro

idioma.

Seleccione “SUBTITULO”

AUTO : Se seleccionará el mismo que fue

seleccionado en la preparación de

“AUDIO”. (Fijación de fábrica)

• Si el idioma seleccionado en la preparación

de “AUDIO” se utiliza durante la

reproducción, los subtítulos no aparecerán.

• Si se utiliza otro idioma durante la

reproducción, los subtítulos aparecerán en el

idioma seleccionado en la preparación de

“AUDIO”

Inglés / Español / Francés / Japonesa :

OTRO

✱✱✱✱

:Se puede seleccionar el otro

idioma.

Seleccione “MENU”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonesa :

OTRO

✱✱✱✱

:Se puede seleccionar el otro

idioma.

Fijaciones iniciales

Cambio del idioma de la pista

de sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al hacer

las fijaciones iniciales se puede cambiar por otro

idioma diferente, si éste se encuentra disponible.

Presione

AUDIO

durante la reproducción

para visualizar

SONIDO en la pantalla.

Presione para

seleccionar idioma.

Visión desde otro ángulo

[DVD solamente]

Algunos discos DVD tienen escenas que han sido

filmadas simultáneamente desde ángulos diferentes.

Con estos discos, la misma escena podrá verse desde

cada uno de estos ángulos diferentes utilizando el botón

ANGLE.

Presione

ANGLE

durante la

reproducción para visualizar

la selección del ángulo.

Presione para

seleccionar el ángulo

deseado.

Selección de vocal para los

discos de Karaoke [DVD/Vídeo CD]

Presione

AUDIO

durante la reproducción

para visualizar la pantalla AUDIO.

Presione (o )

para seleccionar el ajuste

deseado.

Presione (o ) para

ajustar. (DVD solamente)

Guía para rápida

consulta

ELEGIR :

ACTIVO / INACTIVO :

TERMINAR : SUB TITLE

ELEGIR :

ACTIVO / INACTIVO :

TERMINAR : SUB TITLE

ANGULO

: 1

ELEGIR :

ANGULO

: 2

ELEGIR :

ELEG

TERMI

NAR : AUDIO

ELEG

TERMI

NAR : AUDIO

ELEG

TERMI

NAR : AUDIO

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

• Video CD LR L R

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4769

For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]

Algunos discos con películas, vienen con dos o más

títulos. Por ejemplo, si el disco tiene un menú de

títulos grabados, el botón TITLE podrá utilizarse

para seleccionar el título de la película.

Presione

TITLE

durante la reproducción.

Ahora se visualiza una lista de los títulos del

disco.

Utilización de un menú de títulos

[DVD solamente]

TLE MENU

Cas

Love

Dogs

Presione o las

teclas de números para

seleccionar el título

deseado.

Presione

SET

para elegir.

Algunos discos DVD ofrecen un menú especial.

Este menú incluye guías para contenidos únicos,

audio, subtitulos, idiomas, etc. Aunque los

contenidos y las operaciones se cambian, los

siguientes son unos pasos básicos para el uso del

menú.

Presione

durante la reproducción.

El menú de DVD introducido en el disco se

visualiza ahora.

Dogs

of the world

Presione o las

teclas de números

para

seleccionar el ítem deseado.

Presione

SET

para elegir.

Ampliación de la imagen [Vídeo DVD solamente]

Durante la reproducción de un DVD, puede ampliar partes específicas de una imagen y seleccionar la

relación de zoom usando el botón ZOOM.

Presione

ZOOM

repetidamente para cambiar el

tamaño de la imagen como se indica a continuación:

2da

3da

■ Use los botones , , y para desplazar

la posición hacia arriba, hacia abajo, hacia la

izquierda o hacia la derecha.

Utilización de un menú de DVD

[DVD solamente]

DVD MENU

3 . ANGLE

1 . SUBT

TLE

2 . AUD

Spanish Quick Use Guide/ Guía para rápida consulta

Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]

REPROD

MODE DE REPRODUCCION:

NORMAL

ROOT

. .

END

ALTZ

TECHNO

CUB I C

POPS

CTURNE

AZZ

Presione

POWER

en el control remoto o DECK.

Presione

OPEN/CLOSE

y a continuacion

coloque un disco MP3/WMA/JPEG en la bandeja

de discos.

Presione

OPEN/CLOSE

para cerrarla.

Puede utilizar esta unidad para reproducir audio de

formato MP3/WMA/JPEG, grabado para uso personal

con una computadora, etc., en un CD-ROM o CD-RW.

La ejecución no podrá realizarse en algunos casos,

debido a las condiciones de la grabación.

Se visualizará el MENU MP3/WMA/JPEG y la

ejecución se iniciará automáticamente. (Se

visualizará el directorio del CD.)

Estado de la

función

Contador

MODO DE REPRODUCCIÓN

Area de las

carpetas

Area de

archivos

Carpeta

principal

(La carpeta

visualizada

actualmente se

volverá verde)

(El archivo/ la

carpeta se

visualiza con

un cursor.)

:Archivo MP3 :Archivo WMA :Archivo JPEG

:Carpeta :Carpeta principal

■ Ejecución MP3/WMA/JPEG (Durante el modo STOP)

Presione para seleccionar un archivo MP3/WMA

(

) o un archivo JPEG ( ), y presione

SET

PLAY

• MP3/WMA

Búsqueda hacia adelante/hacia atrás

➡Presione

FF/SLOW+

REW/SLOW-

durante la ejecución.

Salto de pista hacia adelante/hacia atrás

➡Presione

SKIP

| o |

SKIP

durante la ejecución.

• JPEG

Búsqueda siguiente/anterior

➡Presione

SKIP

| o |

SKIP

Inicie la muestra-diapositiva

➡Presione

FF/SLOW+

REW/SLOW-

Ampliar una imagen ➡ Presione

ZOOM

Girar una imagen ➡ Presione

ANGLE

Presione

STOP

para detener la operación descrita arriba.

■ Seleccione MODO DE REPRODUCCION

(Durante el modo STOP)

Presione para mover el cursor a MODO DE

REPRODUCCION, y Presione

para seleccionar el

MODO DE REPRODUCCIÓN deseado.

[MODO DE REPRODUCCIÓN]

NORMAL: Todos los archivos se reproducen sólo una vez

REPETICION DE UNA MUSIC:

El archivo seleccionado se reproduce repetidamente.

REPETICION DE UN ARCHIVO:

Los archivos que se encuentran en la carpeta

seleccionada se reproducen repetidamente.

REPETICION DEL DISCO:

Todos los archivos se reproducen repetidamente.

Funcionamiento de la ejecución de MP3/WMA/JPEG

Presione

ACTION

para regresar al DVD MENU

PRINCIPAL.

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4770

ELEG

R : F

JAR: SET

SAL

R : ACTION PAG

NA: SK

SINGLE

SLIDE

Ejecución de JPEG con Tarjeta SD

Los datos de imagen fija (JPEG) creados mediante la

cámara digital, la cámara de video digital o el PC se

pueden ejecutar utilizando una tarjeta SD/MMC.

Inserte la tarjeta SD <El modo VCR y la tarjeta SD

ya han sido insertados.>

Cambia la pantalla

MENU SD

automaticamente.

Presione ACTION.

Presione para

seleccionar “SD CARD

REPRODUCCION,”

y presione SET para

visualizar la pantalla del

MENU SD.

• Durante la grabación el

menú de arriba no se

visualiza. Para visualizar el

menú SD, reinserte la

tarjeta SD.

Nota

ELEGIR

SALIR

: ACTION

FIJAR : SET

PREPARAR VCR

FIJAR RELOJ

FIJAR CANAL

SD CARD REPRODUCCION

LANGUE/LANGUAGE:ESPAÑOL

CANAL DE SALIDA : 3

Configuración de los altavoces

Presione para

seleccionar “AJUSTE DE

ALTAVOCES,” y

Presione

SET

para

visualizar la pantalla

AJUSTE DE ALTAVOCES.

AJUSTE DE ALTAVOCES

ELEG

JAR : SET

TERM

NAR : ACTION

SAL

DA PARA ALTAVOCES :

MULT

CANALES

TAMAÑO DEL ALTAVOZ

BALANCE DE SAL

I EMPO ATRAZADO

Presione para seleccionar, y presione

SET

para fijar.

■ SALIDA PARA ALTAVOCES

Fije el número de altavoces conectados al DECK.

MULTI-CANALES (Predeterminado en fábrica)

Cuando están conectados 3 o más altavoces.

2 CANALES

Cuando están conectados 2 altavoces.

■ TAMAÑO DEL ALTAVOZ

Se determinan las propiedades de frecuencia del

altavoz y la existencia de los altavoces.

FRENTE (GRANDE [predeterminado en fábrica]/

PEQUEÑO)

CENTRO (GRANDE [predeterminado en fábrica]/

PEQUEÑO/NINGUNO)

ENVOLVENTE (GRANDE [predeterminado en

fábrica]/PEQUEÑO/NINGUNO)

SUBWOOFER (ENCENDIDO [predeterminado en

fábrica]/APAGADO)

■ BALANCE DE SALIDA

Ajuste la salida de nivel de volumen para los altavoces.

CENTRO, ENVOLVENTE(DER)/(IZQ), SUBWOOFER

-6db ~ +6db (0db: predeterminado en fábrica)

SEÑAL PRUEBA

El sonido de prueba es la salida en sentido de las

manecillas del reloj.

■ TIEMPO ATRAZADO

Configurar el tiempo atrazado. Da a la salida de

sonido un efecto retrasado que le ofrece la ilusión de

encontrarse en la posición de escucha ideal.

Presione

ACTION

tres o cuatro veces

para salir.

VISUALIZACION DEL MENU SD.

AREA DEL

INDICE

Este área se

utiliza para

visualizar los

archivos

almacenados

en la tarjeta

SD.

EJECUCION

UNICA

MUESTRA-

DIAPOSITIVA

■ SINGLE (EJECUCIÓN ÚNICA)

Este modo permite ampliar y ejecutar una sola imagen

seleccionada del índice de visualización. Además, este

modo permite aplicar a la imagen varias funciones,

incluidas el zoom, la rotación e información de la imagen.

Ampliar una imagen (ZOOM) ➡ Presione ZOOM

PARA GIRAR ➡ Presione ANGLE

Iniciar la muestra-diapositiva

➡ Presione PLAY (vea debajo)

Visualizar la pantalla de información del archivo

➡ Presione DISPLAY.

■ SLIDE SHOW (MUESTRA DIAPOSITIVA)

Este modo permite que se visualice una secuencia de

imágenes, una detrás de la otra. Además, también

permite seleccionar imágenes para visualizarlas, y la

selección de ajuste para los efectos de transición de la

pantalla y la velocidad de transición.

Presione para seleccionar “SINGLE” o

“SLIDE”, y presione SET.

Presione

para seleccionar (vea a la

derecha), y presione SET

repetidamente.

ELEG

R: F

JAR: SET

TERMINAR : ACTION

COM

ENZO

VELOC

DAD : ALTA 2S

TRANSICION : NORMAL

[VELOCIDAD]

Fije el tiempo de transición

ALTA(2 seg)/MEDIANA(5 seg)/BAJA(10 seg)

[TRANSICION]

NORMAL: Para que las imágenes pasen una

a una.

DESLIZAR: Para que las imágenes pasen de

arriba abajo.

DIVICIONES: Para que las imágenes pasen

empezando por el centro y

partiéndose a la izquierda y la

derecha.

COLUMNAS: Para que las imágenes pasen en

una serie de formas tipo bandas

asemejándose a las persianas de

una ventana.

presione ACTION para salir de cada

modo.

Presione

POWER

en el control remoto o el

aparato.

Presione

DVD

para seleccionar el modo DVD.

Guía para rápida

consulta

2 D4763S P36-60 (030512 –§”Ô•Ï•X2nd).p65 2003/05/14, 13:4771

Printed in Indonesia

LSQT0676A

S0303-2073

Panasonic Consumer Electronics Company,

Division of Matsushita Electric Corporation of America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”),

Division of Matsushita Electric of Puerto Rico, Inc.

Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,

Puerto Rico 00985

A ACTION button ...................................................................... 8, 18

Accessories ............................................................................... 4

ADD/DELETE button (Add or Delete a Channel) .................. 8, 19

Audio Broadcast types (Stereo/SAP/Mono) .............................. 26

Audio Mode (Playback, Recording) .......................................... 27

Auto Operation Functions .......................................................... 31

Auto Shut-Off .............................................................................33

B Batteries ..................................................................................... 4

C Channel (“SET UP CHANNEL”) ..............................................18

Channel Up/Down, Tracking/V-Lock Button ............................ 4, 8

Clock (“SET CLOCK”) .............................................................18

Commercial Skip......................................................................31

Connections ..................................................................... 12 ~ 15

Copy Your Tapes (Dubbing) ..................................................... 35

COUNTER RESET button .................................................... 8, 32

Customer Services Directory ...................................................65

D DISPLAY button .................................................................... 8, 11

DSS/CABLE mode button ...................................................... 8, 28

DST (Daylight Saving Time) ....................................................19

E EJECT button ........................................................................ 8, 20

ENTER button (For tuning TV Channel) ............................... 8, 28

F FAST FORWARD/SEARCH button ..................................... 8, 20

H Head Cleaning ............................................................................ 4

I Index Search .............................................................................30

Indicator (Multi Function Display) .............................................11

Initial Setup (Ready to Play) ................................................ 16, 17

INPUT button ........................................................................ 8, 35

L Limited Warranty ............................................................... 64, 65

Location of Controls (Remote, DECK) ............................... 8 ~ 10

M Multi-Brand Control ............................................................ 28, 29

O On-Screen Displays (VCR) ......................................................11

One Touch Recording ............................................................... 21

DECK & VCR

P PAUSE/STILL button (Still Picture) ....................................... 8, 20

PLAY button (Playback a Tape) ............................................. 8, 20

POWER button ........................................................................... 8

PROG button (PROGRAM) .................................................. 8, 24

Program Clear, Review, Replace ............................................. 25

Program End Search................................................................. 30

Q Quality Picture ............................................................................. 4

R REC button (Record on a Tape) ............................................ 8, 21

Record Tab ................................................................................ 6

Remote Sensor .......................................................................... 9

Remote Warning ...................................................................... 34

Repeat Play ...............................................................................32

Reset All Memory Functions ..................................................... 9

REWIND/SEARCH button .................................................... 8, 20

S SAP/Hi-Fi .................................................................................27

SEARCH (Index and Program End Search).............................. 30

SLOW+/SLOW- button (Slow Motion Picture) ..................... 8, 20

Spanish Quick Use Guide ................................................ 66 ~ 71

Specifications ............................................................................ 7

SPEED button ....................................................................... 8, 21

Still (Freeze) Picture ................................................................20

STOP button .......................................................................... 8, 20

T Tape Position, Tape Status .......................................................34

Timer Recording ......................................................................24

Trouble Shooting ................................................................. 62, 63

TV mode button ..................................................................... 8, 28

V VCR Lock .................................................................................33

VCR mode button.................................................................. 8, 28

VCR/TV button ...................................................................... 8, 21

VCR/TV Selector Feature ......................................................... 32

VOLUME +/- button (TV Volume) ......................................... 8, 28

W Warning and Instruction Displays ............................................. 61

Weak Signal Display................................................................. 33

Z ZERO SEARCH button ......................................................... 8, 32

INDEX

A ACTION button ...................................................................... 8, 53

ANGLE button (Multiple Angle Viewing) .................... 8, 37, 51, 59

AUDIO button (Audio Soundtrack Language) ........................ 8, 36

Audio Output (For Selecting Audio Output) ............................... 54

Auto-Power Off Function ...........................................................23

B Bonus Group (For DVD-Audio) ................................................. 41

C CLEAR button ................................................................. 8, 39, 52

Component Video Output .................................................... 10, 13

D Delay Time Setup .....................................................................56

Disc Languages ........................................................................ 53

Direct Navigator .......................................................................42

DISPLAY button (“On-Screen Display”) ............................... 8, 44

DTS ..........................................................................................14

DVD-Audio................................................................................41

DVD Lock Ratings .................................................................... 52

DVD Menu ................................................................................38

DVD mode button .................................................................. 8, 28

DVD-RAM ................................................................................42

F 5.1ch Analog Audio Output .................................................. 15, 51

Frame by Frame Picture ..........................................................23

Forward/Reverse Chapter/Track Skip ......................................23

Forward/Reverse Scene Search ...............................................23

J JPEG ................................................................................ 49 ~ 51

JPEG Playback (SD) ................................................................58

K Karaoke (Vocal Selection for Karaoke Discs) ...........................37

L Language Code List ...................................................................60

M MENU button (To display DVD Menu) ................................. 8, 38

MP3 ..........................................................................................49

Multiple Angle Viewing ............................................................. 37

Multi-channel speaker system ............................................ 15, 55

O OPEN/CLOSE button ............................................................ 8, 22

Optical Digital Audio Output ................................................ 10, 15

Output Balance Setup ................................................................56

DVD

P PAGE button (Still Image Skip) ............................................. 8, 41

PLAY button (Play a Disc) .................................................... 8, 22

Play List .................................................................................... 43

Program Play (For Video CD/ CD) ..........................................39

PROGRESSIVE button .............................................................. 9

Progressive Scan...................................................................... 10

R Random Play (For Video CD/ CD) ...........................................40

Repeat Play ......................................................................... 47, 48

Resume Function...................................................................... 23

RETURN button .................................................................... 8, 22

Rotation............................................................................... 51, 59

S SD Card.............................................................................. 58, 59

SEARCH button

(Forward/Reverse Scene Search) ...................................... 8, 23

SINGLE PLAY Mode ................................................................. 59

SKIP l or l button

(Forward/Reverse Chapter/Track) ..................................... 8, 23

Slide-show ..........................................................................50, 59

SLOW+/SLOW- button (Slow Motion Picture) ..................... 8, 23

Speaker Output Setup ................................................................55

Speaker Position ....................................................................... 57

Speaker Size Setup ...................................................................55

STILL button (Still Picture or Pause) ..................................... 8, 23

Still Mode (For selecting “FIELD” or “FRAME”) ......................57

STOP button .......................................................................... 8, 22

SUB TITLE button

(For selecting Subtitle Language) ........................................ 8, 36

S-Video Out ......................................................................... 10, 13

T Test Signal Setup ...................................................................... 57

TITLE button (Title Menu) ..................................................... 8, 38

TV Mode (For selecting the screen display style) ....................57

2-channel speaker system .................................................. 15, 55

V Video CD ..................................................................................23

VOLUME ADJUST button ..................................................... 8, 40

V.S.S. (Virtual Surround Sound) ........................................... 8, 23

W WMA .........................................................................................49

Z ZOOM button (Picture Zoom) .................................... 8, 37, 51, 59

D4763S P36-60 (030610 –§”Ô•Ï•X2nd).p65 2003/06/10, 18:5972

Panasonic PVD4763S Instrucciones de operación

Marca: Panasonic

Modelo: PVD4763S

Categoría: Reproductores de DVD

Tipo: Instrucciones de operación

Descargar PDF

informe

en otros idiomas

English: Panasonic PVD4763S Operating instructions

Panasonic PVD4763S Instrucciones de operación

Panasonic PVD4763S Instrucciones de operación

en otros idiomas

Artículos relacionados

Otros documentos