Yamaha MCR-N470 El manual del propietario

Marca: Yamaha

Modelo: MCR-N470

Tipo: El manual del propietario

Este manual también es adecuado para

Network CD Receiver

OWNER’S MANUAL

2 En

IMPORTANT SAFETY INSTRUCTIONS

• Explanation of Graphical Symbols

The lightning ﬂ ash with arrowhead symbol, within an equilateral triangle, is

intended to alert you to the presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufﬁ cient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the

presence of important operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including ampliﬁ ers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a

third grounding prong. The wide blade or the third prong are provided for your safety. If the

provided plug does not ﬁ t into your outlet, consult an electrician for replacement of the obsolete

outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories speciﬁ ed by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table speciﬁ ed by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused for long periods

of time.

14 Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s Consumer Electronics

Group want you to get the most out of your equipment by playing it at a safe

level. One that lets the sound come through loud and clear without annoying

blaring or distortion – and, most importantly, without affecting your sensitive

hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and

the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

3 En

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual,

meets FCC requirements. Modiﬁ cations not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2 IMPORTANT: When connecting this product to accessories and/or another product use

only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow

all installation instructions. Failure to follow instructions could void your FCC authorization

to use this product in the USA.

3 NOTE: This product has been tested and found to comply with the requirements listed

in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to

the instructions found in the users manual, may cause interference harmful to the operation

of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all

installations. If this product is found to be the source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of

the following measures:Relocate either this product or the device that is being affected by the

interference.Utilize power outlets that are on different branch (circuit breaker or fuse) circuits

or install AC line ﬁ lter/s.In the case of radio or TV interference, relocate/reorient the antenna.

If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.If

these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America A/V Division, 6600 Orangethorpe Avenue, Buena

Park, CA 90620.The above statements apply ONLY to those products distributed by Yamaha

Corporation of America or its subsidiaries.

FCC CAUTION

Change or modiﬁ cations not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide slot and fully insert.

CAN ICE-3 (B)/NMB-3 (B)

IMPORTANT

Please record the serial number of this unit in the space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit. Retain the Owner’s Manual in a safe place

for future reference.

COMPLIANCE INFORMATION STATEMENT

Responsible Party: Yamaha Corporation of America A/V Division

Address: 6600 Orangethorpe Avenue, Buena Park, CA 90620

Telephone: 714-522-9011

Type of Equipment: Network CD Receiver

Model Name: CRX-N470

This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of

the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated

keeping the radiator at least 20cm or more away from person’s body.

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

The FDA-related label is located on the bottom of the unit.

4 En

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1 To assure the ﬁ nest performance, please read this manual carefully. Keep it in a safe place for

future reference.

2 Install this sound system in a well ventilated, cool, dry, clean place - away from direct sunlight,

heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following

minimum clearances.

Top: 10 cm (4 in), Rear: 6 cm (2.5 in), Sides: 6 cm (2.5 in)

3 Locate this unit away from other electrical appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate

this unit in an environment with high humidity (i.e. a room with a humidiﬁ er) to prevent

condensation inside this unit, which may cause an electrical shock, ﬁ re, damage to this unit,

and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be

exposed to liquid dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or discoloration on the surface of this

unit.

– Burning objects (i.e. candles), as they may cause ﬁ re, damage to this unit, and/or personal

injury.

– Containers with liquid in them, as they may fall and liquid may cause electrical shock to the

user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat

radiation. If the temperature inside this unit rises, it may cause ﬁ re, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all connections are complete.

8 Do not operate this unit upside-down. It may overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage the ﬁ nish. Use a clean, dry

cloth.

12 Only voltage speciﬁ ed on this unit must be used. Using this unit with a higher voltage than

speciﬁ ed is dangerous and may cause ﬁ re, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use of this unit with a voltage other

than speciﬁ ed.

13 To prevent damage by lightning, keep the power cable and outdoor antennas disconnected

from a wall outlet or this unit during a lightning storm.

14 Do not attempt to modify or ﬁ x this unit. Contact qualiﬁ ed Yamaha service personnel when

any service is needed. The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC

power plug from the wall outlet.

16 Be sure to refer to the “Troubleshooting” section for common operating errors before

concluding that this unit is faulty.

17 Before moving this unit, press A to set it to standby mode and disconnect the AC power plug

from the wall outlet.

18 Condensation will form when the surrounding temperature changes suddenly. Disconnect the

power cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become warm. Turn the power off, then

leave this unit alone for cooling.

20 Install this unit near the AC outlet and where the AC power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such as sunshine, ﬁ re or the like. When you

dispose of batteries, follow your regional regulations.

22 Excessive sound pressure from earphones and headphones can cause hearing loss.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS UNIT TO RAIN OR MOISTURE.

This unit is not disconnected from the AC power source as long as it is connected to the wall

outlet, even if this unit itself is turned off by A. This state is called the standby mode. In this

state, this unit is designed to consume a very small quantity of power.

Radio waves may affect electro-medical devices. Do not use this unit near medical devices or

inside medical facilities.

Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or

deﬁ brillator implant.

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

–dusty places

• Insert the battery according to the polarity markings (+ and -).

• Change all batteries if you notice the following condition:

– the operation range of the remote control narrows

• If the batteries run out, immediately remove them from the remote control to prevent an

explosion or acid leak.

• If you ﬁ nd leaking batteries, discard the batteries immediately, taking care not to touch the

leaked material. If the leaked material comes into contact with your skin or gets into your

eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery compartment

thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries

or cause old batteries to leak.

5 En

• Do not use different types of batteries (such as alkaline and manganese batteries) together.

Speciﬁ cation of batteries may be different even though they look the same. Danger of explosion

may happen if batteries are incorrectly replaced.

• Before inserting new batteries, wipe the compartment clean.

• Dispose of batteries according to your regional regulations.

• Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor

immediately.

• When not planning to use the remote control for long periods of time, remove the batteries

from the remote control.

• Do not charge or disassemble the supplied batteries.

The user shall not reverse engineer, decompile, alter, translate or disassemble the software used

in this unit, whether in part or in whole. For corporate users, employees of the corporation itself

as well as its business partners shall observe the contractual bans stipulated within this clause.

If the stipulations of this clause and this contract cannot be observed, the user shall immediately

discontinue using the software.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a qualiﬁ ed service person

should remove the cover or attempt to service this device.

DANGER

This unit emits visible laser radiation when open. Avoid direct eye exposure to beam.

When this unit is plugged into the wall outlet, do not place your eyes close to the

opening of the disc tray and other openings to look into inside.

CAUTION

Use of controls or adjustments or performance of procedures other than those

speciﬁ ed herein may result in hazardous radiation exposure.

The laser component in this product is capable of emitting radiation exceeding the

limit for Class 1.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should

be cut off and an appropriate 3 pin plug ﬁ tted. For details, refer to the instructions described below.

Note

The plug severed from the mains lead must be destroyed, as a plug with bared ﬂ exible cord is

hazardous if engaged in a live socket outlet.

■ Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH

THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond

with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked

with the letter N or coloured BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth terminal of the three pin plug.

6 En

Information for users on collection and disposal of old equipment

and used batteries:

These symbols on the products, packaging, and/or accompanying documents

mean that used electrical and electronic products and batteries should not be

mixed with general household waste.

For proper treatment, recovery and recycling of old products and used

batteries, please take them to applicable collection points, in accordance

with your national legislation.

By disposing of these products and batteries correctly, you will help to save

valuable resources and prevent any potential negative effects on human

health and the environment which could otherwise arise from inappropriate

waste handling.

For more information about collection and recycling of old products and

batteries, please contact your local municipality, your waste disposal service

or the point of sale where you purchased the items.

Information on Disposal in other Countries outside the European

Union:

These symbols are only valid in the European Union. If you wish to discard

these items, please contact your local authorities or dealer and ask for the

correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this

case it complies with the requirement set by the EU Battery Directive for the

chemical involved.

We, Yamaha Music Europe GmbH hereby declare that this unit is in compliance with the

essential requirements and other relevant provisions of Directive 1999/5/EC.

Yamaha Music Europe GmbH

Siemensstr. 22-34 25462 Rellingen, Germany

Tel: +49- 4101-303-0

Handling USB devices

• Yamaha is not liable for any loss or corruption of data in USB devices that are used. It is

recommended that you make backups of data for restoring in the event of data loss.

• Some USB devices may not function properly.

Handling Bluetooth communications

• The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many

types of equipment. While Bluetooth compatible devices use a technology minimizing the

inﬂ uence of other components using the same radio band, such inﬂ uence may reduce the speed

or distance of communications and in some cases interrupt communications.

• The speed of signal transfer and the distance at which communication is possible differs

according to the distance between the communicating devices, the presence of obstacles, radio

wave conditions and the type of equipment.

• Yamaha does not guarantee all wireless connections between this unit and devices compatible

with Bluetooth function.

Bluetooth

• Blue tooth is a technology for wireless communication between devices within an area of about

10 meters (33 ft) employing the 2.4 GHz frequency band, a band which can be used without a

license.

7 En

Table of Contents

What you can do with this unit······8

Introduction······9

Accessories······9

About this manual······9

Part names······10

Front panel······10

Rear panel······11

Front panel display······12

Remote control······13

Preparations······14

Connecting speakers······14

Connecting the antenna······15

Preparing to connect to a network ······15

Turning on the power······16

Connecting to a network······17

Selecting connection method······17

Connecting using MusicCast CONTROLLER······18

Connecting to a wireless network······19

Connecting to a wired network······21

Updating the firmware······22

Listening to music······23

Listening to CDs······23

Playing back music on USB devices······24

Playing back music via Bluetooth connection······25

Playing back music from external devices······27

Listening to DAB stations (CRX-N470D only)······28

Listening to FM radio stations······31

Radio Data System (U.K. and Europe models only)······33

Listening to the Internet radio······34

Playing back songs in the computer······35

Presetting network content······37

Playing back music with AirPlay······38

Connect the unit directly with a

mobile device

······39

More on playback

Features such as shuffle/repeat playback, displaying song information, and presetting favorites make this unit even more convenient to use.

Shuffle/Repeat

playback

Press during playback.

• The shuffle indicator in the front panel display switches

as shown below each time you press the button.

* The range of shuffle depends on the media being played

back.

Press during playback.

• The repeat indicator in the front panel display switches

as shown below each time you press the button.

* The range of repeat depends on the playback media.

Shuffle (Random) playback

Performs shuffle playback.*

Not displayed Does not perform shuffle playback.

Repeat playback

Repeats the song being played back.

Performs repeat playback.*

Not displayed Does not perform repeat playback.

REPEAT

SHUFFLE

• Operation is the same for playback of content

from PCs (servers), USB devices, AirPlay, and CDs.

Note

More on playback

41 En

Playback information

While content from a PC (server), a USB device, AirPlay, or

a CD is being played back, the song title, elapsed time, etc.

can be shown on the front panel display.

Press during playback.

• The display switches in the order shown below each

time you press the button.

*1 If the song title cannot be obtained, the file name may be

displayed.

*2 Only when playing an audio CD.

*3 Only when playing an audio CD and when there is

information to display.

USB/AirPlay/Server CD

Song title*

Playing time

Artist name

Remaining time of the

song

Album title

Remaining time of the

disc*

Playing time Song title*

Artist name*

Album title*

eora

DISPLAY

• Characters shown on the front panel display are

alphanumerics only.

Note

More on playback

42 En

Presetting content to

FAVORITES

You can register your favorite content to the FAVORITES

buttons (A to C) so that it can be played back easily in the

future.

Press and hold any of the FAVORITES

buttons during the playback of the

content.

• The content being played back is registered to that

FAVORITES button.

Press the FAVORITES button to which the

content that you want to play back is

registered.

• The content that is registered to the pressed FAVORITES

button is played back.

* To play back content from this input source, the connected

device must be configured.

Presetting content

Selecting content that is registered to

FAVORITES

(A C)

• When presetting content to a FAVORITES

button, any content that is already registered to

that button will be replaced.

• Pressing a FAVORITES button triggers one of the

actions below, depending on the input source

of the content registered to it.

Input sources

What happens when the

FAVORITES buttons are pressed

PC (Server)

The registered songs are played

back.

NetRadio

The registered radio station is

played back.

AirPlay*

The input source is switched to

AirPlay.

Bluetooth*

The input source is switched to

Bluetooth.

USB

The registered songs are played

back.

The registered songs are played

back.

DAB (CRX-N470D

only)

The registered radio/DAB station is

played back.

AUX 1, 2*

Depending on the content that is

registered, the input source is

switched to AUX1 or AUX2.

Note

More on playback

43 En

Adjusting sound

quality

The unit’s sound quality can be adjusted. Refer to “Option

menu for sound quality” at right.

1 Press .

2 Press S/T to select the desired item

and press .

3 Press S/T to change the setting and

press .

• To set other items, repeat steps 2 and 3.

4 Press to exit the Option settings.

Using the sleep timer

You can set the time after which the unit automatically

enters standby mode. The time can be selected from 120/

90/60/30 min., or OFF.

Press repeatedly to select the time.

• The SLEEP indicator lights up when the sleep timer is

set.

Option menu for sound quality

SLEEP

2, 3





ENTER

1, 4

OPTION

• To cancel audio quality configuration, press

OPTION.

(Bold: default)

Equalizer

Adjusts low frequency [Bass] and high frequency [Treble].

The setting is also applied when using headphones.

(-10 to 0 to +10)

Balance

Adjusts the volume balance of the left and right speakers.

This setting is not applied when using headphones.

(Lch. +10 to --center-- to Rch.+10)

Music Enhancer

Regenerates musical elements that are lost through

compression.

(On, Off)

When playing back a high quality music source, such as

FLAC or WAV, it is recommended to set this function to

[Off]. When playing back an audio CD that has not been

compressed, this function is not available even if [On] is

set.

• To cancel the sleep timer, press SLEEP again.

Note

More on playback

44 En

Option settings

Option settings allow you to configure the unit to suit

how you will use it.

1 Press .

• The Option menu list is shown on the front panel

display. Refer to “Option menu list” (& P.45).

2 Select a desired option menu with S/

T and press .

3 Change the setting with S/T and

press .

• Repeat step 3 if there is a sub menu.

• Press W to cancel the setting and return to the

previous level.

• Repeat steps 2 and 3 if you want to set another

menu item.

4 Press to exit the Option settings.

1, 4

OPTION

2, 3







ENTER

More on playback

45 En

*1 Only when the radio is played back

*2 CRX-N470D only

Option menu list

Menu Sub menu Default Function

Preset Delete

(& P.32) Deletes preset stations.

Auto Preset

Sets the Auto Preset.

Equalizer

(& P.43)

Bass 0 Adjusts low frequency.

Treble 0 Adjusts high frequency.

Balance (& P.43) center

Adjusts the volume balance of the left and

right speakers.

Music Enhancer (& P.43) Off Enables/disables Music Enhancer.

Initial Scan

*1,*2

(& P.28)

Scans all receivable frequencies and

registers them in the unit.

Tune Aid

*1,*2

(& P.30) Shows the level of received DAB signal.

Network

Info

Status

Shows the connection status of the

NETWORK jack.

LAN MAC Address Shows MAC address.

WiFi MAC Address Shows MAC address.

Bluetooth Addr Confirms the Bluetooth address.

MusicCast Info Shows the information on MusicCast.

SSID Confirms the SSID.

Direct Info Shows the information for Wireless Direct.

Network Name

Shows the name of the unit that appears on

the network.

vTuner ID Confirms the vTuner ID.

IP Address 0.0.0.0 Confirms the IP address.

Network

Info

Subnet Mask 0.0.0.0 Confirms the subnet mask.

Default Gateway 0.0.0.0 Confirms the default gateway.

DNS Server(P) 0.0.0.0 Confirms the primary DNS server.

DNS Server(S) 0.0.0.0 Confirms the secondary DNS server.

Network

Config

Select Network Wired Selects a network connection method.

DHCP On Enables/disables DHCP.

System

Config

AutoPowerStby

Sets the unit to enter standby mode

automatically (& P.16).

Net Standby On

Sets the network status for when the unit is

in standby mode (& P.16).

Bluetooth On Sets Bluetooth.

Initialize Set

Resets to the factory default settings.

Firmware

Update

Version Shows the firmware version of the unit.

Update

Network

Updates the firmware of the unit (& P.22).

Menu Sub menu Default Function

46 En

Troubleshooting

Refer to the table below when the unit does not function properly. If your problem is not listed below or if the instruction below does not help, turn off the unit,

disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.

First, check that the connectors of each cable are securely inserted in to jacks on each device. Check also that the power cable is plugged into an outlet.

General

Problem Cause Solution

The unit enters the standby mode soon

after the power is turned on.

The unit does not operate properly.

The power cable is not properly connected. Connect the power cable firmly.

The unit got a strong electric shock from an outside source, such as lighting

or excessive static electricity.

Hold down A on the front panel for more than 10 seconds to initialize and

reboot the unit. (If the problem persists, unplug the power cable from the

wall outlet and plug it again after 30 seconds or more.)

No sound.

No appropriate source has been selected.

Select an appropriate source with INPUT on the front panel or the source

buttons on the remote control (& P.10, 13).

Speaker connections are not secure. Secure the connections (& P.14).

The volume is minimum or mute. Turn up the volume.

Sound is heard from the speaker on one

side only.

Source device or speakers are not connected properly.

Connect the source device or speaker cables properly (& P.14, 27). If the

problem persists, the cables may be defective.

Noise is heard.

This unit is too close to digital or radio-frequency equipment. Move this unit away from such equipment.

The audio cable between this unit and Source device is defective.

Connect the audio cable firmly. If the problem persists, use another audio

cable.

The power suddenly turns off.

The sleep timer may be set (& P.43).

Turn on the unit and play the source again.

Auto Power Standby function is activated. (& P.16).

There is noise interference from digital or

high-frequency equipment.

This unit is too close to the digital or high-frequency equipment. Place this unit farther away from such equipment.

The remote control does not work or does

not function properly.

The remote control may be outside its operation range. Operate the remote control within its operation range (& P.16).

The remote control sensor on this unit may be exposed to direct sunlight or

strong lighting such as an inverter type fluorescent lamp.

Change the orientation of lighting or the unit, or location of the unit.

The battery may be worn out. Replace the batteries with new ones (& P.13).

There are obstacles between the sensor of this unit and the remote control. Remove the obstacles.

Troubleshooting

47 En

Network

Problem Cause Solution

The network feature does not function. The network parameters (IP address) have not been obtained properly.

Enable the DHCP server function of the router. In addition, in the [Network

Config] of the option settings of the unit, set [DHCP] to [On]. If you want to

configure the network parameters manually, check that you are using an IP

address which is not used by other network devices in your network

(& P.45). For details on how to set the router, contact the manufacturer of

the router.

Playback stops (songs cannot be played

back continuously).

There are unsupported files in the server.

Remove the files (including image files or hidden files) which the unit does

not support from the folder being played back.

The unit does not detect the PC.

The media sharing setting is not correct.

Configure the sharing setting and select the unit as a device to which music

contents are shared (& P.35).

Some security software installed on your PC is blocking the access of the

unit to your PC.

Check the setting of the security software installed in your PC.

The unit and PC are not in the same network.

Check the network connections and your router settings, and then connect

the unit and the PC to the same network.

The files in the PC cannot be viewed or

played back.

The files are not supported by the unit or the media server.

Use the file format supported by both the unit and the media server

(& P.53).

Internet radio cannot be played.

The selected Internet radio station is currently not available.

There may be a network problem at the radio station, or the service may

have been stopped. Try the station later or select another station.

The selected Internet radio station is currently broadcasting silence.

Some Internet radio stations broadcast silence at certain of times of the day.

In this case, no sound is output even if the signal is received. Try the station

later or select another station.

Access to the network is restricted by the firewall settings of your network

devices (such as the router).

Check the firewall settings of your network devices. Internet radio can be

played only when it passes through the port designated by each radio

station. The port number varies depending on the radio station.

The dedicated application for mobile

devices does not detect the unit.

The unit and mobile devices are not in the same network.

Check the network connections and your router settings, and then connect

the unit and the PC to the same network.

Update of the firmware via network failed. The network connection is unstable.

Try updating again after a while. Or update the firmware via USB memory

device (& P.22).

Troubleshooting

48 En

Bluetooth

The iPhone does not recognize the unit

when using AirPlay.

A multi-SSID supported router is used.

The network separation function of the router may prevent the iPhone

from accessing the unit. When connecting an iPhone, use SSID that can

access the unit.

The unit cannot connect to the Internet

via a wireless router (access point).

The wireless router is turned off. Turn on the wireless router.

The unit is placed too far from the wireless router. Place the unit and the wireless router closer to each other.

There is an obstacle between the unit and the wireless router. Remove the obstacles.

Wireless network is not found.

Wireless communication is interrupted by the electromagnetic waves

emitted from a microwave oven or other wireless devices.

When using the unit via wireless connection, place it away from devices

emitting electromagnetic waves.

Access to the network is restricted by the firewall settings of your wireless

router.

Check the firewall setting of the wireless router.

Problem Cause Solution

Cannot make the unit pair with a

Bluetooth device.

The unit is turned off. Turn the unit on and perform the pairing (& P.25).

The [Bluetooth] of the option settings is set to [Off]. Set it to [On].

Another Bluetooth device is connected.

Terminate current Bluetooth connection, and perform pairing with the new

device.

This unit and the device are too far apart. Pair the unit and device within a distance of 10 m (33 ft).

There is a device (microwave oven, wireless LAN, etc.) that outputs signals

in the 2.4 GHz frequency band nearby.

Move this unit away from the device that is emitting radio-frequency

signals.

A Bluetooth adapter, etc., that you want to pair with this unit has a passkey

other than “0000.”

Use a device whose passkey is “0000.”

The Bluetooth device does not support A2DP. Perform pairing with a device which supports A2DP.

Cannot make a Bluetooth connection.

The [Bluetooth] of the option settings is set to [Off]. Set it to [On].

Another Bluetooth device is connected.

Terminate current Bluetooth connection, then establish a Bluetooth with

that device again.

The Bluetooth function of the device is turned off. Turn on the Bluetooth function of the device.

The pairing information has been deleted.

Delete the Bluetooth device's pairing information and perform pairing

again.

This unit is not registered on the device’s Bluetooth connection list. Perform pairing again (& P.25).

Troubleshooting

49 En

Disc

USB devices

No sound is produced, or the sound is

interrupted during playback.

The volume of the Bluetooth device is set too low. Turn up the volume of the Bluetooth device.

The Bluetooth device is not set to send Bluetooth audio signals to the unit.

Switch the output of Bluetooth audio signals of the Bluetooth device to the

unit.

The Bluetooth connection of the unit with the device has terminated. Perform Bluetooth connection operations again (& P.25).

There is a device (microwave oven, wireless LAN, etc.) that outputs signals

in the 2.4 GHz frequency band nearby.

Move this unit away from the device that is emitting radio-frequency

signals.

This unit and the Bluetooth device are too far apart. Move the Bluetooth device to within 10 m (33 ft) of the unit.

The Bluetooth function of the device is turned off. Turn on the Bluetooth function of the device.

The

Bluetooth

device is not set to send

Bluetooth

audio signals to this unit.

Check that the Bluetooth function of the Bluetooth device is set properly.

Problem Cause Solution

Playback does not start after a disc is

inserted.

Some button operations do not work.

The disc inserted in the unit may not be supported. Use a disc supported by the unit (& P.52).

Playback does not start (or stops

immediately) after pressing on

the unit or on the remote control.

The disc may be dirty. Wipe the disc clean (& P.52).

The disc inserted in the unit may not be supported. Use a disc supported by the unit (& P.52).

If the unit was moved from a cold to warm place, condensation may have

formed on the disc reading lens.

Wait for an hour or two until the unit adjusts to the room temperature, and

try again.

Problem Cause Solution

The unit does not detect the USB device.

The USB device is not connected to the USB jack securely.

Turn off the unit, reconnect your USB device, and turn the unit on again

(& P.24).

A USB device in a format other than FAT16/32 format is used. Use a USB device with FAT16 or FAT32 format.

Folders and files in the USB device cannot

be viewed.

The data in the USB device is protected by encryption. Use a USB device without an encryption function.

Troubleshooting

50 En

DAB reception (CRX-N470D only)

FM reception

Problem Cause Solution

Cannot tune into any DAB stations. The initial scan operations were not performed. Perform the initial scan operations (& P.28).

The initial scan operations are not

successful and [Not Found] is shown on

the front panel display.

The DAB signals are too weak.

Use the DAB Tune Aid feature to conform the best position of the antenna

(& P.30).

The positioning of the antenna is not optimal for DAB reception.

There is no DAB coverage in your area.

Check with your dealer or WorldDMB online at http://www.worlddab.org

for a listing of the DAB coverage in your area.

There is noise interference (e.g. hiss,

crackle or jitter)

The antenna needs to be repositioned. Readjust the position of the antenna (& P.15).

The DAB signals are too weak.

Use the DAB Tune Aid feature to conform the best position of the antenna

(& P.30).

The DAB station information is not shown

or is inaccurate.

The DAB station may be temporarily out of service, or the DAB station

information is not provided by the DAB broadcaster.

Contact the DAB broadcaster.

Problem Cause Solution

FM stereo reception is noisy.

The antenna is not connected properly.

Make sure the antenna is connected properly and change the position of

the antenna (& P.15).

The radio station you selected may be far from your area, or the antenna

input is poor.

Use a commercially available outdoor antenna. For details, consult a

specialist store.

Automatic tuning does not work.

The radio station you selected may be far from your area, or the antenna

input is poor.

Use a commercially available outdoor antenna. For details, consult a

specialist store.

Use the manual tuning method (& P.31).

Cannot select a preset radio station. The preset (memory) may have been erased. Preset radio stations again (& P.31, 32).

There is distortion, and clear reception

cannot be obtained even with a good FM

antenna or an outdoor antenna.

Multipath reflection or other radio interference may be occurring. Change the height, direction, or placement of the antenna.

Troubleshooting

51 En

Messages on the front panel display

Message Cause Solution

Access Denied Access to the PC is denied.

Configure the sharing settings and select the unit as a device to which

music contents are shared (& P.35).

Access Error

The unit cannot access the USB device.

Turn off the unit and reconnect your USB device. If the problem persists, try

another USB device.

There is a problem with the signal path from the network to the unit.

Make sure your router and modem are turned on. Check the connection

between the unit and your router (or hub) (& P.17).

Initializing The unit is starting up.

Wait until the message disappears. If the message stays more than 3

minutes, turn off the unit and turn it on again.

Loading... The unit is loading the specified file/content. Wait until the unit finishes loading.

No Content Selected folder does not contain playable files. Select a folder with playable files (& P.53).

No Disc

The disc inserted in the unit may not be supported. Use a disc supported by the unit (& P.52).

The disc may be dirty, or foreign matter may be attached to it.

Wipe the disc clean. Alternatively, remove foreign matter adhered to the

disc.

Disc is set upside-down. Set the disc with the labeled side facing up.

No Songs The disc does not contain playable files. Set a disc with playable files (& P.52).

Not Connected The unit is not connected to the network. Check the network connection.

Overcurrent

The connected USB device is not supported by the unit.

Disconnect the USB device, turn off the unit, and turn it on again. If this

does not solve the problem for the USB device, it is not playable on the unit.

USB device is not connected properly.

Unable to play

The unit cannot play back the songs stored on the USB devices or the

computer for some reason.

Check if the format of files you are trying to play is supported by the unit

(& P.53).

Version Error Firmware update has failed. Update the firmware again.

52 En

Supported devices/media and file formats

Supported devices/

media

PC with Windows Media Player 11 or Windows Media

Player 12 installed.

NAS compatible with DLNA version 1.5.

• The unit is compatible with USB mass storage class

devices (e.g., flash memories or portable audio players)

using FAT16/FAT32 format.

• Do not connect devices other than the USB mass

storage class devices (USB charger, USB hub, etc.), PCs,

card readers, and external hard discs.

• USB devices with encryption cannot be used.

• Depending on the manufacturer or type of the USB

device, the unit may not recognize the USB device or

some functions may be unavailable.

• This unit is designed for use with audio CD, CD-R/RW

(ISO 9660 format) with any of the following logos

printed on the disc or the disc jacket.

Audio CD

CD-R/RW*

* Discs which bear one of the following.

FOR CONSUMER

FOR CONSUMER USE

FOR MUSIC USE ONLY

• 8-cm discs are playable with this unit.

Set a disc in the inner recessed area of the disc tray.

Notes on discs

• Do not set any other type of disc other than stated

above in this unit. Doing so may damage the unit.

• CD-R/RW cannot be played back unless finalized.

Finalization means the process for making a disc to be

ready for playback on a compatible device .

• Some discs cannot be played back depending on the

disc characteristics or recording conditions.

• Do not use any non-standard shaped discs such as a

heart-shaped disc.

• Do not use discs with many scratches or a crack on their

surface, or warped/glued discs.

Handling discs

• Do not touch the surface of the disc.

Hold a disc by its edge or center hole.

• Use a soft-tipped pen when writing

on the label side of a disc.

• Do not put tape, seal, glue, etc., on a disc.

• Do not use a protective cover to prevent scratches.

• Do not set foreign object on the disc tray.

• Do not set more than one disc in this unit at one time.

This could cause damage to both this unit and the discs.

• If a disc becomes dirty, wipe it

with a clean, dry soft cloth from

the center out to the edge. Do not

use record cleaner or paint

thinner.

• Do not use any lens cleaners as

they may cause malfunction.

• Do not expose discs to direct sunlight, high

temperature, high humidity, or dust.

• When a disc is not being used, remove it from this unit

and store in an appropriate case.

PCs

NAS

USB devices

Discs

Supported devices/media and file formats

53 En

File format

File format the unit supporting is as follows.

* Linear PCM format only

• To play back FLAC files, you need to install server software that supports sharing of FLAC

files via DLNA on your PC or use a NAS that supports FLAC files.

• Digital Rights Management (DRM) files cannot be played back.

DLNA/USB

Format

Sampling

frequency

(kHz)

Quantization

bitrate (bit)

Bitrate

(kbps)

Number of

channels

Gapless

playback

supported

WAV

32/44.1/48/

88.2/96/176.4/

192

16/24 - 2 3

MP3 32/44.1/48 - 8-320 2 -

WMA 32/44.1/48 - 8-320 2 -

MPEG-4 AAC 32/44.1/48 - 8-320 2 -

FLAC

32/44.1/48/

88.2/96/176.4/

192

16/24 - 2 3

ALAC

32/44.1/48/

88.2/96

16/24 - 2 3

AIFF

32/44.1/48/

88.2/96/176.4/

192

16/24 - 2 3

Disc

Format Sampling frequency (kHz) Quantization bitrate

MP3 8-48 16

WMA 16-48 16

54 En

Specifications

The contents of this manual apply to the latest specifications as of the publishing date. To

obtain the latest manual, access the Yamaha website then download the manual file.

Input

AUX IN

AUX 1 Stereo L/R: RCA

AUX 2 3.5 mm stereo mini jack

Laser

Type Semiconductor laser GaAs/GaAlAs

Wave length 790 nm

Output power 7 mW

Media CD, CD-R/RW

Audio format Audio CD, MP3, WMA

USB

Supported file format MP3, WMA, MPEG4 AAC, WAV, FLAC, ALAC, AIFF

Network

Interface 100Base-TX/10Base-T

Internet radio vTuner service supported

PC client function DLNA Ver. 1.5 (DMP/DMR function) supported

Supported file format Same as USB supported file format

AirPlay AirPlay supported

Wi-Fi

Wireless network standards IEEE802.11 b/g/n

Radio frequency 2.4 GHz

Available security methods WEP, WPA2-PSK (AES), Mixed Mode

Tuner

Preset memory 30

Tuning range FM

U.S.A. and Canada models: 87.5 MHz to 107.9 MHz

Other models: 87.5 MHz to 108.0 MHz

DAB (CRX-N470D ONLY)

Preset Memory 30

Tuning range DAB 174 to 240 MHz (Band III)

Compatibility DAB/DAB+

Bluetooth

Bluetooth version Ver. 2.1+EDR

Supported profile

A2DP (Advanced Audio Distribution Profile)

AVRCP (Audio/Video Remote Control Profile)

Compatible codecs SBC, AAC (AAC is Sink only)

Operating modes Sink or Source

Wireless output Bluetooth Class 2

Maximum communication range 10 m (33 ft) (without interference)

Amplifier section

Maximum output power 22 W + 22 W (6 Ω, 1 kHz, 10% THD)

Frequency response 20 Hz to 20 kHz (0±3 dB)

Total harmonic distortion ≤ 0.05 % (10 W/6 Ω 1 kHz)

Headphones

500 mV/32 Ω

Input: 1 kHz 300 mV, 32 Ω terminated

Subwoofer output power 1.5 V/1 kΩ

General

Power supply/Frequency AC 100 to 240 V, 50/60 Hz

Power consumption 25 W

Standby power consumption

Network standby off: 0.4 W

Network standby on

Wired (Ethernet): 1.8 W

Wireless (Wi-Fi/Wireless Direct/Bluetooth):

1.9W/1.9W/1.7W

Dimensions (W × H × D)

(with wireless antenna upright)

270 × 110 × 330 mm

(270 × 179 × 330 mm)

Weight 3.0 kg

55 En

Trademarks

AirPlay, iPad, iPhone, iPod, iPod touch and iTunes are trademarks of Apple Inc., registered in the

U.S. and other countries.

AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac with OS X Mountain

Lion or later, and Mac and PC with iTunes 10.2.2 or later.

(as of July 2015)

DLNA™ and DLNA CERTIFIED™ are trademarks or registered trademarks of Digital Living Network

The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.

The Wi-Fi Protected Setup Identifier Mark is a mark of the Wi-Fi Alliance.

Wi-Fi, Wi-Fi Alliance, Wi-Fi CERTIFIED, Wi-Fi Protected Setup, WPA and WPA2 are trademark or

regitstered trademark of Wi-Fi Alliance.

The Bluetooth

word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and

any use of such marks by Yamaha Corporation is under license.

Bluetooth protocol stack (Blue SDK)

(For CRX-N470D)

The unit supports DAB/DAB+ tuning.

Explanations regarding GPL

This product utilizes GPL/LGPL open-source software in some sections. You have the right to

obtain, duplicate, modify, and redistribute this open-source code only. For information on GPL/

LGPL open source software, how to obtain it, and the GPL/LGPL license, refer to the Yamaha

Corporation website (http://download.yamaha.com/sourcecodes/musiccast/).

Windows™

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

Internet Explorer, Windows Media Audio and Windows Media Player are either registered trademarks

or trademarks of Microsoft Corporation in the United States and/or other countries.

Android™

Android and Google Play are trademarks of Google Inc.

MusicCast is a trademark or registered trademark of Yamaha Corporation.

56 En

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai asetusten muutto saattaa altistaa vaaralliselle

säteilylle tai muille vaarallisille toiminnoille.

Advarsel: Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå

utsættelse for stråling.

Bemærk: Netafbryderen A er sekundært indkoblet og ofbryder ikke strømmen fra nettet. Den

indbyggede netdel er derfor tilsluttet til lysnettet så længe netstikket sidder i stikkontakten.

Observer: Nettbryteren A er sekundert innkoplet. Den innebygdenetdelen er derfor ikke frakoplet

nettet så lenge apparatet er tilsluttet nettkontakten.

Klass 1 laseraparat

Varning! Om apparaten används på annat sättþän i denna bruksanvisning speciﬁ cerats, kan

användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.

Observera! Strömbrytaren A är sekundärt kopplad och inte bryter inte strömmen från nätet. Den

inbyggda nätdelen är därför ansluten till elnätet så länge stickproppen sitter i vägguttaget.

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa

altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja roiskevedelle.

Huom. Toiminnanvalitsin A on kytketty toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.

Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon aina silloin, kun pistoke on

pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR

URKOPPLAD. BETRAKTA EJ STRÅLEN.

OBSERVERA

Apparaten kopplas inte bort från växelströmskällan (nätet) så länge som den är ansluten till

vägguttaget, även om själva apparaten har stängts av.

ADVARSEL

Netspæendingen til dette apparat er IKKE afbrudt, sålæenge netledningen siddr i en stikkontakt,

som er t endt - også selvom der or slukket på apparatets afbryder.

VAROITUS

Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta.

Manual Development Group

Published 06/2016 NV-A0

Yamaha Global Site

http://www.yamaha.com/

Yamaha Downloads

http://download.yamaha.com/

CRX-N470OM/EN

http://europe.yamaha.com/warranty/

AVEEA71102A

Important Notice: Guarantee Information for customers in EEA*

and Switzerland

For detailed guarantee information about this Yamaha product, and Pan-EEA* and

Switzerland warranty service, please either visit the website address below (Printable file is

available at our website) or contact the Yamaha representative office for your country.

* EEA: European Economic Area

English

Transcripción de documentos

N e t wo r k C D R e ce i ve r OWNER’S MANUAL EN IMPORTANT SAFETY INSTRUCTIONS 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. We Want You Listening For A Lifetime Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels. • Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 1 2 3 4 5 6 7 8 9 10 11 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. 2 En COMPLIANCE INFORMATION STATEMENT FCC INFORMATION (for US customers) Responsible Party: Yamaha Corporation of America A/V Division Address: 6600 Orangethorpe Avenue, Buena Park, CA 90620 Telephone: 714-522-9011 Type of Equipment: Network CD Receiver Model Name: CRX-N470 This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA. 3 NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:Relocate either this product or the device that is being affected by the interference.Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America A/V Division, 6600 Orangethorpe Avenue, Buena Park, CA 90620.The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries. NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. FCC CAUTION Change or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. FOR CANADIAN CUSTOMERS The FDA-related label is located on the bottom of the unit. To prevent electric shock, match wide blade of plug to wide slot and fully insert. CAN ICE-3 (B)/NMB-3 (B) IMPORTANT Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain the Owner’s Manual in a safe place for future reference. 3 En CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 18 Condensation will form when the surrounding temperature changes suddenly. Disconnect the power cable from the outlet, then leave this unit alone. 19 When using this unit for a long time, this unit may become warm. Turn the power off, then leave this unit alone for cooling. 20 Install this unit near the AC outlet and where the AC power plug can be reached easily. 21 The batteries shall not be exposed to excessive heat such as sunshine, fi re or the like. When you dispose of batteries, follow your regional regulations. 22 Excessive sound pressure from earphones and headphones can cause hearing loss. 1 To assure the fi nest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place - away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances. Top: 10 cm (4 in), Rear: 6 cm (2.5 in), Sides: 6 cm (2.5 in) 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fi re, damage to this unit, and/or personal injury. 5 Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: – Other components, as they may cause damage and/or discoloration on the surface of this unit. – Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury. – Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit. 6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fi re, damage to this unit, and/or personal injury. 7 Do not plug in this unit to a wall outlet until all connections are complete. 8 Do not operate this unit upside-down. It may overheat, possibly causing damage. 9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable. 11 Do not clean this unit with chemical solvents; this might damage the fi nish. Use a clean, dry cloth. 12 Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fi re, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified. 13 To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a wall outlet or this unit during a lightning storm. 14 Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons. 15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet. 16 Be sure to refer to the “Troubleshooting” section for common operating errors before concluding that this unit is faulty. 17 Before moving this unit, press A to set it to standby mode and disconnect the AC power plug from the wall outlet. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off by A. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power. Radio waves may affect electro-medical devices. Do not use this unit near medical devices or inside medical facilities. Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker implant or defibrillator implant. ■ Notes on remote controls and batteries • • • • • • • • 4 En Do not spill water or other liquids on the remote control. Do not drop the remote control. Do not leave or store the remote control in the following conditions: – places of high humidity, such as near a bath – places of high temperatures, such as near a heater or stove – places of extremely low temperatures – dusty places Insert the battery according to the polarity markings (+ and -). Change all batteries if you notice the following condition: – the operation range of the remote control narrows If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak. If you fi nd leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery compartment thoroughly before installing new batteries. Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak. • • • • • • ■ For U.K. customers Do not use different types of batteries (such as alkaline and manganese batteries) together. Specification of batteries may be different even though they look the same. Danger of explosion may happen if batteries are incorrectly replaced. Before inserting new batteries, wipe the compartment clean. Dispose of batteries according to your regional regulations. Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor immediately. When not planning to use the remote control for long periods of time, remove the batteries from the remote control. Do not charge or disassemble the supplied batteries. If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet. ■ Special Instructions for U.K. Model IMPORTANT THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: The user shall not reverse engineer, decompile, alter, translate or disassemble the software used in this unit, whether in part or in whole. For corporate users, employees of the corporation itself as well as its business partners shall observe the contractual bans stipulated within this clause. If the stipulations of this clause and this contract cannot be observed, the user shall immediately discontinue using the software. Blue: NEUTRAL Brown: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug. LASER SAFETY This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device. DANGER This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into the wall outlet, do not place your eyes close to the opening of the disc tray and other openings to look into inside. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The laser component in this product is capable of emitting radiation exceeding the limit for Class 1. 5 En Handling USB devices Information for users on collection and disposal of old equipment and used batteries: • These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation. • By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. • Handling Bluetooth communications • • For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. The 2.4 GHz band used by Bluetooth compatible devices is a radio band shared by many types of equipment. While Bluetooth compatible devices use a technology minimizing the influence of other components using the same radio band, such influence may reduce the speed or distance of communications and in some cases interrupt communications. The speed of signal transfer and the distance at which communication is possible differs according to the distance between the communicating devices, the presence of obstacles, radio wave conditions and the type of equipment. Yamaha does not guarantee all wireless connections between this unit and devices compatible with Bluetooth function. Bluetooth • Information on Disposal in other Countries outside the European Union: These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Pb Yamaha is not liable for any loss or corruption of data in USB devices that are used. It is recommended that you make backups of data for restoring in the event of data loss. Some USB devices may not function properly. Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the EU Battery Directive for the chemical involved. We, Yamaha Music Europe GmbH hereby declare that this unit is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Yamaha Music Europe GmbH Siemensstr. 22-34 25462 Rellingen, Germany Tel: +49-4101-303-0 6 En Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft) employing the 2.4 GHz frequency band, a band which can be used without a license. Table of Contents What you can do with this unit······8 Introduction······9 Accessories······9 About this manual······9 Part names······10 Front panel······10 Rear panel······11 Front panel display······12 Remote control······13 Connect the unit directly with a mobile device······39 More on playback······40 Shuffle/Repeat playback······40 Playback information······41 Presetting content to FAVORITES······42 Adjusting sound quality······43 Using the sleep timer······43 Option settings······44 Preparations······14 Troubleshooting······46 Connecting speakers······14 Connecting the antenna······15 Preparing to connect to a network ······15 Turning on the power······16 General······46 Network······47 Bluetooth······48 Disc······49 USB devices······49 DAB reception (CRX-N470D only)······50 FM reception······50 Messages on the front panel display······51 Connecting to a network······17 Selecting connection method······17 Connecting using MusicCast CONTROLLER······18 Connecting to a wireless network······19 Connecting to a wired network······21 Updating the firmware······22 Listening to music······23 Listening to CDs······23 Playing back music on USB devices······24 Playing back music via Bluetooth connection······25 Playing back music from external devices······27 Listening to DAB stations (CRX-N470D only)······28 Listening to FM radio stations······31 Radio Data System (U.K. and Europe models only)······33 Listening to the Internet radio······34 Playing back songs in the computer······35 Presetting network content······37 Playing back music with AirPlay······38 Supported devices/media and file formats······52 Supported devices/media······52 File format······53 Specifications······54 Trademarks······55 7 En What you can do with this unit • This unit is a Network CD Receiver, on which you can enjoy playing back music files stored on your media servers (PC or NAS) connected to the same network, USB devices, audio content on Internet radio, FM radio, CD, AirPlay devices (iPhone/iTunes), and external devices including DVD players, by connecting the unit to your home network and audio system. • You can select songs and operate the unit easily by using the free dedicated "MusicCast CONTROLLER" app supporting iOS/Android. When you install the “MusicCast CONTROLLER” app on your mobile device and connect to a network... You can enjoy Internet radio and music files stored in mobile devices, PCs, servers, and other equipment. 1 FM radio DAB (CRX-N470D only) You can control this unit from your mobile device and establish a wireless connection with other devices that are compatible with MusicCast CONTROLLER for vastly expanding your entertainment possibilities. 9 This unit 6 Internet radio Router* 7 PC or NAS 2 External device 4 CD 3 USB device 5 Bluetooth- 8 AirPlay compatible device * You need a commercially available wireless router (access point) when you use a mobile device. 1 Listening to FM radio stations (& P.31) 5 Play back music in a Bluetooth compatible device (& P.25) Listening to DAB stations (CRX-N470D only) (& P.28) 6 Play back Internet radio (& P.34) 2 Play back music in an external device (& P.27) 7 Play back music files stored on your PC or NAS (& P.35) 3 Play back music in a USB device (& P.24) 8 Play back your iPhone with AirPlay (& P.38) 4 Play back a CD (& P.23) 9 Use of MusicCast CONTROLLER (& P.17) 8 En Introduction Confirm the package contents and useful points of this manual. Accessories About this manual • Instructions and illustrations used in this manual refer to the CRX-N470, unless otherwise specified. • How to operate this unit is described mainly using the remote control. • iOS and Android mobile devices are collectively referred to as “mobile devices.” The specific type of mobile device is noted in explanations as needed. • “iPhone” described in this manual may also refer to “iPod” or “iPad.” • Illustrations may differ from actual item depicted. Remote control FM antenna (for CRX-N470) • Symbols: DAB/FM antenna (for CRX-N470D) Note Indicates tips for usage and supplementary information. & Indicates the corresponding reference page(s). This icon appears for features that require a network connection. Batteries (x 2) (AA, R6, UM-3) 9 En Part names Familiarize yourself with all parts and their functions. 1 Power indicator Front panel Lights up when the unit is on. 2 A (Power) (& P.16) 3 PHONES Connect headphones to this jack. ED C • When headphones are connected to it, there is no sound from the speakers or subwoofer. Note B 4 USB jack (& P.24) 5 Disc tray (& P.23) Wi-Fi BLUETOOTH 6 VOLUME INPUT A CONNECT PHONES (& P.23, 24, 36) PRESET 7 / (& P.32) (Play/pause) (& P.23, 24, 36) USB 8 (Stop) (& P.23, 24, 34, 36) CONNECT (& P.18) Use to connect to a network. 9 1 2 3 4 5 6 7 8 9 0 (Open/close the disc tray) (& P.23) 0 INPUT (& P.23, 24) Change the input source. (The source is shown on the front panel display.) A VOLUME Controls the volume. B Remote control sensor C Front panel display (& P.12) D Wi-Fi indicator (& P.19) E Bluetooth indicator (& P.25) 10 En Part names 1 Power cable (& P.16) Rear panel 2 Wireless antenna (& P.19) 3 AUX 1 jacks (RCA input) (& P.27) 4 AUX 2 jack (mini jack input) (& P.27) 5 ANTENNA jack (& P.15) 6 SUBWOOFER jack (& P.14) 7 NETWORK jack (& P.15) Connects to a network using a commercially available network cable. 8 SPEAKERS terminals (& P.14) 1 2 3 4 5 6 7 8 11 En Part names Front panel display 1 1 Multi information display Shows various information, such as music information and the radio frequency. Characters shown on the front panel display are alphanumerics only. 2 STEREO indicator Lights up when the unit is receiving a signal from an FM stereo broadcast. 3 TUNED indicator 2 3 45 6 6 Shuffle/repeat indicator Lights up when you shuffle or repeat music of your CD, USB device or computer. Note Adjusting display brightness You can adjust the brightness of the display by pressing the DIMMER button on the remote control (& P.13). • Each press of the button changes the brightness: bright (default), mid dim, or dim. Lights up when the unit is receiving a signal from an FM station. 4 MUTE indicator Lights up when the sound is muted (& P.13). 5 SLEEP indicator Lights up when the sleep timer is set (& P.43). 12 En Part names 1 Infrared signal transmitter Remote control 2 (Open/close the disc tray) (& P.23) 3 Source buttons 1 2 Installing batteries Switch the input source to be played. A 4 Numeric buttons (& P.23, 37) 5 MEMORY (& P.31, 37) 3 6 Audio control, cursor control buttons (& P.23, 24, 34, 36) 4 Check the “+” and “-” of the batteries and insert them facing the correct directions. 7 REPEAT (& P.40) 8 SHUFFLE (& P.40) 5 B Note 9 DIMMER (& P.12) 0 FAVORITES (& P.42) A A (Power) (& P.16) 6 B OPTION (& P.44) C D 7 8 9 0 E F G C VOLUME +/– Controls the volume. D MUTE Turns mute on or off. E DISPLAY (& P.41) F HOME (& P.34, 36) G SLEEP (& P.43) 13 En • Change both batteries when the operation range of the remote control decreases. Preparations Connect speakers, the antenna, etc. and turn the unit on. Do not connect the power cable of the unit until you have finished connecting all cables. Connecting speakers 1 Right speaker Left speaker Remove the insulation from the ends of the speaker cables to expose the bare wires. 1 3 15 mm (5/8 in.) 2 2 Speaker cable Connect speakers to the unit, as the illustration shows. Subwoofer • Prepare speakers, subwoofer and speaker cables separately. Monaural pin cable • For connection of the speakers, refer to the owner’s manual supplied with them. Caution • If the bare speaker wires touch each other or any metal part of the unit, it could damage the unit and/or the speakers. • Use speakers of at least 6 Ω impedance. Note • Make sure that left and right (L, R) connections and polarity (red: +, black: -) are correct. If connections are incorrect, the sound will be unnatural. • You can also connect a subwoofer to the unit (it must have a built-in amplifier). 14 En Preparations Connecting the antenna 1 2 Connect the supplied antenna to the unit. Install it with pins where the unit can obtain good reception. Supplied antenna Preparing to connect to a network Connecting to a wireless network Connecting to a wired network Raise the wireless antenna. Connect the unit to a router, as the illustration shows. • Raise the wireless antenna on the rear panel. • Connect using a commercially available network cable (CAT-5 or higher straight cable). 2 1 Caution • Do not apply excessive force to the wireless antenna. • Do not remove the antenna. Network cable LAN Router Note • Be sure to stretch out the antenna as the illustration shows. • If radio reception with the supplied antenna is not satisfactory, a commercially available outdoor antenna may improve reception. 15 En Preparations Option menu regarding power (System Config) Turning on the power (Bold: default) For details on operating the option menu, refer to "Option settings" (& P.44). Plug the power cable into a power outlet, and press . AutoPowerStby • The unit turns on. • Press Within 6 m (20 ft) again to turn the unit off (standby mode). • When the power of the unit is turned on for the first time after purchase, the network settings preparation message (Share WiFi Set) may appear. If it appears, refer to step 6 in “Sharing the settings of an iOS device” (& P.20). 30° 30° This configures whether the unit automatically enters the standby mode. (On, Off) When set to On, the unit automatically enters the standby mode under the following conditions according to the input source: • Network/Bluetooth/CD/USB: When no operation or playback is performed for 20 minutes • Other sources: When no operation is performed for 8 hours Net Standby This configures whether the unit performs network operations while in the standby mode. (On, Off) When set to Off, network operations while the unit is in standby mode are stopped, and power consumption is reduced. When Net Standby is Off, the following features cannot be used while the unit is in standby mode: - Using the MusicCast CONTROLLER app (& P.18) to turn on the unit's power - Charging of USB devices - AirPlay - Bluetooth 16 En Connecting to a network You can play back music files stored on your PC, mobile devices, DLNA*-compatible NAS, or audio content on the Internet by connecting this unit to a network. * Digital Living Network Alliance Selecting connection method Using the MusicCast CONTROLLER app is the most simple and recommended way to connect to a network. Note • When playing back high-resolution audio sources, it is recommended to use a wired network in order to maintain a stable connection. Connecting using MusicCast CONTROLLER • For details on Internet connection, refer to the owner’s manuals of your network devices. • Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the unit to the network devices or the Internet. In this case, change the setting of the security software or network devices. This unit can be controlled from your mobile device. Go to "Connecting using MusicCast CONTROLLER" (& P.18) 17 En Connecting without using MusicCast CONTROLLER Connecting to a wireless network Connecting to a wired network Go to "Connecting to a wireless network" (& P.19) Go to "Connecting to a wired network" (& P.21) Connecting to a network Connecting using MusicCast CONTROLLER Note • For setting up MusicCast CONTROLLER, you can also refer to the "MusicCast Setup Guide", which is available on the following site: Yamaha Downloads http://download.yamaha.com/ 1 Connect this unit to the same home network as your mobile devices. 1 2 3 Install the “MusicCast CONTROLLER” app on your mobile device. • This app can be downloaded for free from the App Store or Google Play. 2 Start “MusicCast CONTROLLER” and tap “Setup”. • Follow the app’s instructions. Press and hold seconds. for about 5 Wi-Fi • The Wi-Fi indicator starts flashing. Configure the settings by following the app’s instructions. • For more information about MusicCast CONTROLLER, refer to the following site: http://www.yamaha.com/musiccast/ BLUETOOTH 3 18 En Connecting to a network Connecting to a wireless network About WPS WPS (Wi-Fi Protected Setup) is a standard established by the Wi-Fi Alliance, which allows easy establishment of a wireless home network. Setup can be performed using a WPS (Wi-Fi Protected Setup) button, or by sharing settings from an iOS device (iPhone, etc.). Note • If the unit is placed far away from the wireless router (access point), a connection may not be able to be established. In that case, place them closer together. Setup using a WPS button • A wireless router (access point) with a WPS button is required. 1 2 3 4 5 6 Press . 1 OPTION Select [Network Config] with S/T, and press . Select [Select Network] with S/T, and press . 2, 3, 4, 5 /, ENTER Select [Wireless] with S/T, and press . Select [WPS] with S/T, and press • You cannot simultaneously use this setting with a wired network connection or Wireless Direct (& P.39). . Press the WPS button on the wireless router (access point). • Once connected, the Wi-Fi indicator stays lit. 19 En Connecting to a network Note Sharing the settings of an iOS device This applies the network settings of your iOS device to the unit. • An iOS device with iOS 7.1 or later is required. • Before starting setup, check that your iOS device is connected to the wireless router. 1 2 3 4 5 6 Press . Select [Network Config] with S/T, and press . Select [Select Network] with S/T, and press . 1 OPTION Select [Wireless] with S/T, and press . Select [Share WiFi Set] with S/T, and press . 2, 3, 4, 5 /, ENTER • A message about the initialization of the network will be shown on the front panel display. Press ENTER. Display the Wi-Fi setup screen on the iOS device and select the unit from “SETUP A NEW AIRPLAY SPEAKER...”. • Follow the on-screen instructions displayed on the iOS device. • Once connected, the Wi-Fi indicator stays lit. 20 En • If the network settings of an iOS device are applied, all network and Bluetooth connection settings as well as account information for streaming services will be initialized. Connecting to a network Note Connecting to a wired network 1 2 3 4 Press • If you are using a router that does not support DHCP, configure the network settings from [Network Config] within Option settings (& P.44). • When setting the subnet manually, each server must be connected to the same subnet as the unit (& P.45). . Select [Network Config] with S/T, and press . Select [Select Network] with S/T, and press . Select [Wired] with S/T, and press . 1 OPTION • By default, [Wired] is set for the unit. 2, 3, 4 /, ENTER 21 En Connecting to a network Note Updating the firmware • When Internet speed is not fast enough or the unit is connected to the wireless network via a wireless network adapter, network update may not be possible depending on the condition of the wireless connection. In this case, try again or update the firmware using a USB memory device. The firmware can be downloaded from the Yamaha Website. When a new firmware for the unit is released, a message to update your current firmware will be shown on the front panel display (when the unit is connected to the Internet only). If this message is shown, follow the steps below to perform the update. 1 2 3 4 Press . To update the firmware using a USB memory device Select [Firmware Update] with S/T, and press . 1 OPTION Select [Update] with S/T and press . Select [Network] with S/T, and press . 2, 3, 4 / ENTER • Press ENTER again to begin the update. 5 • Do not operate the unit or disconnect the power cable and network cables while updating. • When the update finishes, messages are shown in the following order: “UPDATE SUCCESS”, “PLEASE ...”, and “POWER OFF!” Press A (Power) on the front panel. • The update is applied. 22 En You can download the firmware to a USB memory device, and connect that USB memory device to the USB jack on the unit. • Select [USB] in step 4 to start the update. Listening to music Note Listening to CDs 1 2 3 2 Press INPUT to select [CD]. Or, press on the remote control. 1 INPUT • When CD playback is stopped, playback will resume from the beginning of the song last played. Pressing while playback is stopped will clear resume playback. Set a CD in the disc tray. • Press • You can cancel the song number selected with the numeric buttons by pressing W. to open/close the disc tray. 1 CD Playback starts. The remote control functions are shown below. Play/pause Stop Skip to the beginning of the song being played back, or skip to the previous song. Press and hold to fast rewind. Skip to the next song. Press and hold to fast forward. SHUFFLE Starts shuffle playback (& P.40). REPEAT Starts repeat playback (& P.40). 1 - 9, 0 Specify the song number. ENTER Confirmation of the song number selected with the numeric buttons. • This unit allows playback of audio CDs, and data CDs in which MP3/WMA files are recorded. For details on playable CDs, see “Supported devices/media” (& P.52). 3 23 En • If you turn off the unit with CD selected as the input source and a CD set in it, the unit automatically plays back the set CD next time you turn on the unit. Listening to music Note Playing back music on USB devices 1 2 3 Press INPUT to select [USB] or press on the remote control. Connect a USB device to the USB jack. Browse and select a song. S T Shows other items. ENTER/X Confirms the selected item and proceeds to the next level or starts playback. HOME Shows the top-level item. W Returns to the previous item. DISPLAY Finishes browsing and displays information about the content being played back. 4 • Some USB devices may not work properly even if they meet the requirements. Playability of and power supply to all USB devices are not guaranteed. 1 INPUT • Stop playback before disconnecting the USB device. 2 1 USB liability for the loss of data saved on a USB device connected to the unit. As a precaution, it is recommended to make backup copies of important files. 3, 4 Play/pause Moves to the next or previous song in the folder. Stop SHUFFLE Starts shuffle playback (& P.40). REPEAT Starts repeat playback (& P.40). • A USB device is automatically charged when it is connected to the unit (except when Net Standby is Off (& P.16)). However, some devices may not charge when connected. Caution • Yamaha and suppliers do not accept any Playback starts. / • This unit allows playback from USB devices on which music files are saved. For details on playable USB devices, see “Supported devices/ media” (& P.52). 24 En Listening to music Note Playing back music via Bluetooth connection Pairing a Bluetooth device and playing back music When connecting a Bluetooth device to the unit for the first time, the device must be registered (paired) to the unit. After pairing has been performed once, it is easy to reconnect after the Bluetooth connection has been disconnected. Set the Bluetooth setting of your Bluetooth device to ON before connecting. 1 2 3 Press • If the device does not connect to the unit automatically after the pairing is completed, select the unit again in the Bluetooth setting on your device. • If pairing information for a device is deleted, you will need to perform pairing of that device again in order to connect it again. 1 BLUETOOTH • If another device is already connected to the unit, press and hold BLUETOOTH to terminate the Bluetooth connection, then perform pairing with the new device. • If a passkey is required during the pairing operation, enter the number “0000.” • For details on connecting, see the owner’s manual of your device. Bluetooth device . Select this unit in the Bluetooth settings of your device. • The Bluetooth indicator lights up when a connection is established. Play back music using your Bluetooth device. 25 En Listening to music Connecting a paired Bluetooth device and playing back music Note 1 • If connecting from the unit, the unit searches for the Bluetooth device connected the last time. In this case, make sure that device's Bluetooth function is turned on. If the unit is connected to another device via Bluetooth connection, terminate that connection (see “Terminating the Bluetooth connection” on the right) before connecting to the target device. 1 Terminating the Bluetooth connection Perform Bluetooth connection. • Bluetooth connection can be terminated by any of the following methods: • Connecting from the unit: Press BLUETOOTH. - Terminate the Bluetooth connection from the connected device. • Connecting from the Bluetooth device: Turn on the Bluetooth function of the Bluetooth device, and select the unit from the available device list. 2 • Decrease the volume of the unit before playback. Otherwise, playback volume may be too loud. 1, 2 - Change to another input source. - Press and hold BLUETOOTH. - Set the unit to standby mode. • The Bluetooth indicator lights up when a connection is established. Play back music using your Bluetooth device. Wi-Fi BLUETOOTH 26 En Listening to music Playing back music from external devices 2 This unit allows playback from external devices, such as a DVD player. 1 2 3 4 3 Unplug the power cable of the unit and connect the external device to the unit. 1 Stereo pin cable (RCA connector) 3.5 mm stereo mini-plug cable • Prepare commercially available cables for connection. Plug the power cable of the unit back into the wall outlet and press to turn the unit on. DVD player, etc. Portable music player, etc. Change the input source. • Each time AUX is pressed, the input source switches between AUX 1 and AUX 2. Play back the connected external device. Note • Decrease the volume of the unit and the connected external device before connection. Otherwise, playback volume may be too loud. • Use the jacks (AUX 1 or AUX 2) according to the device to be connected (& P.11). For the connection of each external device, refer to its supplied owner’s manual. • For details on playback, refer to the owner’s manual supplied with the external device. 27 En Listening to music Note Listening to DAB stations (CRX-N470D only) 1 Press 2 Press S/T to select [Initial Scan] and press 1 TUNER Initial scan repeatedly to select [DAB]. OPTION • Initial scan starts automatically when you select [DAB] for the first time. 2 / Tuning in DAB stations 2 Press . - Initial scan starts and finishes automatically. • If an initial scan is performed, stored DAB station information and preset DAB stations are cleared. • This unit can receive only Band III DAB frequencies. Frequency in MHz/Channel label • When scanning is completed, the number of receivable DAB stations is shown on the front panel display momentarily, and the first station stored is played. 1 when the source is DAB. - Option menu is shown on the front panel display. See “Connecting the antenna” (& P.15) for connecting the supplied antenna to the unit. Press • You can also perform an initial scan from the Option settings. repeatedly to select [DAB]. • When the unit cannot receive the DAB signal, “Off Air” is shown on the front panel display. Press W/X to select a DAB station. 28 En Listening to music Note Presetting DAB stations Use the preset function to store your favorite 30 DAB stations. 1 Tune in a DAB station you want to preset (& P.28) and press . • The preset number flashes on the front panel display. 1 MEMORY OPTION 2 / 3 ENTER • To cancel the DAB preset setting, press . • You can change the information of the DAB station shown on the front panel display by pressing the DISPLAY button. The display switches in the order shown below each time you press the DISPLAY button. STATION (default) DLS (Dynamic Label Segment) ENSEMBLE CHANNEL/FREQ (Channel label and frequency) SIGQ. (signal quality) AUDIO FORMAT 2 3 DISPLAY Press S/T to select the desired preset number. Press Use the Option settings to delete a preset station. 1 Press to complete presetting. 1 TUNER Selecting preset DAB stations 1 2 Deleting a preset station when the source is DAB. - The Option menu is shown on the front panel display. 2 Press S/T to select [Preset Delete] and press . 3 Press S/T to select the preset number to be Press deleted. repeatedly to select [DAB]. 2 / Press S/T to select a preset station. 4 Press - The preset station is deleted. 5 Press 29 En . to exit the Option settings. Listening to music Note Confirming the reception You can confirm the DAB signal level. This is useful when setting up the antenna. 1 2 3 Press when the source is [DAB]. • Option menu is shown on the front panel display. Press S/T to select [Tune Aid] and press . Press S/T to change the channel label. 1, 4 OPTION • The measured DAB signal reception level is displayed. 2, 3 4 S/T ENTER • The level is from 0 (none) to 100 (best). Press to exit the Option settings. 30 En • When performing Tune Aid and the DAB signal is weak, try adjusting the position of the antenna to obtain good reception. Listening to music Listening to FM radio stations Note • If station reception is weak, you can tune into a station manually by pressing the W/X button repeatedly. Playback in this case is monaural. Note • Auto preset replaces all currently-stored stations with newly-stored stations. 1 TUNER See “Connecting the antenna” (& P.15) for connecting the supplied antenna to the unit. Tuning in FM stations 1 2 Press 2 / . Press and hold W/X. • Automatic tuning starts, then stops automatically when a station is tuned in. STEREO TUNED 1 TUNER Presetting FM stations Auto preset Tunes in stations with good reception and presets them automatically. 1 2 3 Press • To cancel the auto preset, press . • You can also preset stations automatically from the Option menu (& P.44). . Press more. Press • You can preset up to 30 FM stations. 2, 3 MEMORY and hold for 2 seconds or . • Auto preset starts, and when it finishes, “Completed!” is shown on the front panel display. 31 En Listening to music Manual preset 1 2 Note Tune into a station you want to preset (& P.31). Press . • To cancel manual preset setting, press . Deleting a preset station 2 MEMORY Use the option settings to delete a preset station. OPTION 1 Press OPTION when the source is FM. - The Option menu is shown on the front panel display. • The preset number flashes on the front panel display. 4 ENTER 3 / - To cancel deleting preset stations, press OPTION. 2 Press S/T to select [Preset Delete] and press ENTER. 3 4 3 Press S/T to select the preset number to be Press S/T to select the desired preset number. Press deleted. 4 Press ENTER. - The preset station is deleted and [Deleted!] is shown on the front panel display. to preset the station. 5 Press OPTION to exit the Option settings. Selecting preset FM stations 1 2 Press . 1 TUNER Press S/T to select a station. • The number of a registered preset can also be selected using the numeric buttons. 2 / 32 En Listening to music Note Radio Data System (U.K. and Europe models only) The unit can receive Radio Data System information. Press when the source is FM. • Each press of the button changes the information displays shown below. PService (Program Service) PTY (Program Type) RT (Radio Text) CT (Clock Time) Frequency DISPLAY 33 En • If the signal transmission of the Radio Data System station is too weak, this unit may not be able to receive Radio Data System information completely. In particular, RT (Radio Text) information uses a lot of bandwidth, so it may be less available compared to other types of information. Listening to music Note Listening to the Internet radio Make sure that the unit is connected to the Internet properly (& P.17). 1 2 Radio station name (default) 1 NET Playing time Song title • You can register your favorite Internet radio stations to the “Bookmarks” folder by accessing the following website with the web browser on your PC. http://yradio.vtuner.com Press repeatedly and select [NetRadio]. Browse the Internet and select a radio station. - Before registering Internet radio stations, play back any of the Internet radio stations with the unit. - To use this feature, you need the vTuner ID of the unit and your e-mail address to create your personal account. You can check the vTuner ID in [Network Info] (& P.45) in the option settings. • The remote control functions are shown below. 3 S/T Shows other items. ENTER/X Confirm the selected item and proceed to the next level or start playback. HOME Show the top-level item. W Back to the previous item. DISPLAY Finish browsing and display information about the content being played back. • Some Internet radio stations may not be receivable during certain time periods. 2, 3 • This feature makes use of the vTuner radio station database. • This service may be canceled without prior notice. • The stations of the Internet radio can be preset (& P.37). Playback starts. • To stop playback, press • Playback information can be shown by pressing the DISPLAY button while Internet radio is played back, as shown below. . 34 En Listening to music Playing back songs in the computer Note • For details on media sharing settings, refer to the Help of Windows Media Player. 2 For a PC or a NAS with other DLNA server software installed Refer to the owner’s manual of your device or software and configure the media sharing settings. Setting the media sharing of music files To play back music files in your computer with this unit, you need to configure the media sharing settings between the unit and computer (with Windows Media Player 11 or later). (Example: Windows Media Player 12 (Windows 7)) 1 2 3 4 5 Start Windows Media Player 12 on your PC. 3 Select “Stream,” then “Turn on media streaming.” • The control panel window of your PC is shown. Click “Turn on media streaming.” Select “Allowed” from the drop-down list next to the unit's model name. • For details on the file formats that this unit can play back, refer to “File Formats” (& P.53). 4 Click “OK” to exit. 35 En Listening to music Note Playing back songs in the PC 1 2 3 Press repeatedly and select [Server]. Browse and select a song. S/T Shows other items. ENTER/X Confirm the selected item and proceed to the next level or start playback. HOME Show the top-level item. W Back to the previous item. DISPLAY Finish browsing and display information about the content being played back. • The music files in your PC can be preset (& P.37). 1 NET Playback starts. Play/pause / Move to the next or previous song in the folder. 2, 3 Stop SHUFFLE Starts shuffle playback (& P.40) REPEAT Starts repeat playback (& P.40) • If playback is not possible, check the network connections and your router settings, and then connect the unit and the PC to the same network. 36 En Listening to music Note Presetting network content • If is pressed during presetting, the preset is canceled. Presetting network content allows it to be played back more easily in the future. Presetting network content 2 The following types of network content can be preset: • Internet radio • Music files stored in a PC (server) 1 2 3 1, 3 MEMORY Press during the playback of the network content. Enter the desired preset number using the numeric buttons. • The numbers from 1 to 37 are available for presets. Press to preset the station. 1 NET Selecting preset network content 1 2 2 Press • If the input preset number already has content registered, the content is overwritten. . Enter the preset number using the numeric buttons. • The content that is preset for the number is played back when the unit is connected to the network. 37 En Listening to music Playing back music with AirPlay Make sure that the unit and your PC or iPhone are connected to the same router (& P.17). Note (Example) When the iPhone recognizes the unit, on the screen. appears • For an iPhone with iOS7/iOS8/iOS9 installed, the indication is displayed within the control center. To display the control center, swipe the iPhone screen in an upward direction. • You can also use the unit and remote control to play back, pause, stop, and skip songs. 1 Canceling AirPlay Playing back songs with an iPhone 1 2 3 Turn on the unit and display the playback screen on the iPhone. Tap 3 2 and select the unit's name. iPhone CRX-N470 XXXX • The input source switches to [AirPlay] (except when Net Standby is Off (& P.16)). Play back songs with the iPhone. Playing back songs with iTunes 1 2 • Tap/click on the iPhone/iTunes screen and select a device other than the unit from the speaker list. Or, change the unit’s input source to something other than AirPlay. iPhone iOS7/iOS8/iOS9 Turn on the unit and start iTunes. Click and select the unit's name. (Example) When iTunes recognizes the unit, the iTunes window. 1 • The input source switches to [AirPlay] (except when Net Standby is Off (& P.16)). Play back songs with iTunes. 2 My Computer CRX-N470 XXXX 38 En appears on Connect the unit directly with a mobile device Connect the unit directly with a mobile device wirelessly (Wireless Direct). Put up the wireless antenna of the unit in advance (& P.15). 1 2 3 4 5 6 Press . Note Select [Network Config] with S/T, and press . Select [Select Network] with S/T, and press . Select [Direct] with S/T, and press . • You cannot simultaneously use this setting with a wired network connection or a wireless network connection. Mobile device This unit Select desired security method with S/T, and press . 1 OPTION • Refer to the Note at right. Check the SSID and the security key. • These are required for step 7. • You can check the values from the option menu [Network Info] - [Direct Info]. 7 • The security methods selectable in step 5 are [OPEN] and [WPA2-PSK(AES)]. If [OPEN] is selected, the connection may be insecure since the communication is not encrypted. 2, 3, 4, 5 /, ENTER Configure the Wi-Fi settings of the mobile device. • Enable the Wi-Fi function of the mobile device. • When the access points are listed, select the SSID you have checked in step 6. • When the mobile device prompts you to enter a password, enter the security key you have checked in step 6. 39 En • When using Wireless Direct, you cannot connect the unit to the Internet. Therefore, the Internet services, such as Internet radio, are unavailable. • For details about how to set up the Wi-Fi connection of the mobile device, see the user's guide of your mobile device. More on playback Features such as shuffle/repeat playback, displaying song information, and presetting favorites make this unit even more convenient to use. Note Shuffle/Repeat playback Shuffle (Random) playback Press during playback. • The shuffle indicator in the front panel display switches as shown below each time you press the button. Performs shuffle playback.* Not displayed Does not perform shuffle playback. * The range of shuffle depends on the media being played back. Repeat playback Press during playback. REPEAT SHUFFLE • The repeat indicator in the front panel display switches as shown below each time you press the button. Repeats the song being played back. Performs repeat playback.* Not displayed Does not perform repeat playback. * The range of repeat depends on the playback media. 40 En • Operation is the same for playback of content from PCs (servers), USB devices, AirPlay, and CDs. More on playback Note Playback information While content from a PC (server), a USB device, AirPlay, or a CD is being played back, the song title, elapsed time, etc. can be shown on the front panel display. Press during playback. AL B U M M e t eora • The display switches in the order shown below each time you press the button. USB/AirPlay/Server CD 1 Song title* Playing time Artist name Remaining time of the song*2 Album title Remaining time of the disc*2 Playing time Song title*1,*3 DISPLAY Artist name*3 Album title*3 *1 If the song title cannot be obtained, the file name may be displayed. *2 Only when playing an audio CD. *3 Only when playing an audio CD and when there is information to display. 41 En • Characters shown on the front panel display are alphanumerics only. More on playback Note Presetting content to FAVORITES • When presetting content to a FAVORITES button, any content that is already registered to that button will be replaced. • Pressing a FAVORITES button triggers one of the actions below, depending on the input source of the content registered to it. You can register your favorite content to the FAVORITES buttons (A to C) so that it can be played back easily in the future. Input sources Presetting content Press and hold any of the FAVORITES buttons during the playback of the content. • The content being played back is registered to that FAVORITES button. Selecting content that is registered to FAVORITES Press the FAVORITES button to which the content that you want to play back is registered. FAVORITES (A ∼ C) • The content that is registered to the pressed FAVORITES button is played back. What happens when the FAVORITES buttons are pressed PC (Server) The registered songs are played back. NetRadio The registered radio station is played back. AirPlay* The input source is switched to AirPlay. Bluetooth* The input source is switched to Bluetooth. USB The registered songs are played back. CD The registered songs are played back. FM DAB (CRX-N470D only) The registered radio/DAB station is played back. AUX 1, 2* Depending on the content that is registered, the input source is switched to AUX1 or AUX2. * To play back content from this input source, the connected device must be configured. 42 En More on playback Adjusting sound quality Note 1, 4 OPTION The unit’s sound quality can be adjusted. Refer to “Option menu for sound quality” at right. 1 2 3 4 Press (Bold: default) Adjusts low frequency [Bass] and high frequency [Treble]. The setting is also applied when using headphones. (-10 to 0 to +10) . 2, 3 / ENTER Press S/T to change the setting and press . Balance Adjusts the volume balance of the left and right speakers. This setting is not applied when using headphones. (Lch. +10 to --center-- to Rch.+10) Music Enhancer Regenerates musical elements that are lost through compression. (On, Off) When playing back a high quality music source, such as FLAC or WAV, it is recommended to set this function to [Off]. When playing back an audio CD that has not been compressed, this function is not available even if [On] is set. • To set other items, repeat steps 2 and 3. to exit the Option settings. Using the sleep timer You can set the time after which the unit automatically enters standby mode. The time can be selected from 120/ 90/60/30 min., or OFF. Press Option menu for sound quality Equalizer Press S/T to select the desired item and press . Press • To cancel audio quality configuration, press OPTION. SLEEP repeatedly to select the time. • The SLEEP indicator lights up when the sleep timer is set. 43 En Note • To cancel the sleep timer, press SLEEP again. More on playback Option settings Option settings allow you to configure the unit to suit how you will use it. 1 2 Press . • The Option menu list is shown on the front panel display. Refer to “Option menu list” (& P.45). Select a desired option menu with S/ T and press . 1, 4 OPTION 3 Change the setting with S/T and press . 2, 3 // ENTER • Repeat step 3 if there is a sub menu. • Press W to cancel the setting and return to the previous level. 4 • Repeat steps 2 and 3 if you want to set another menu item. Press to exit the Option settings. 44 En More on playback Option menu list Menu Sub menu Default Deletes preset stations. Auto Preset*1 Sets the Auto Preset. Equalizer (& P.43) Default Function 0.0.0.0 Confirms the subnet mask. Default Gateway 0.0.0.0 Confirms the default gateway. DNS Server(P) 0.0.0.0 Confirms the primary DNS server. 0 Adjusts low frequency. Treble 0 Adjusts high frequency. DNS Server(S) 0.0.0.0 Confirms the secondary DNS server. Adjusts the volume balance of the left and right speakers. Select Network Wired Selects a network connection method. Music Enhancer (& P.43) *1,*2 center Off Network Config Enables/disables Music Enhancer. Scans all receivable frequencies and registers them in the unit. (& P.28) Tune Aid*1,*2 (& P.30) Network Info Network Info Sub menu Subnet Mask Bass Balance (& P.43) Initial Scan Menu Function Preset Delete*1 (& P.32) System Config Shows the level of received DAB signal. DHCP On Enables/disables DHCP. AutoPowerStby On Sets the unit to enter standby mode automatically (& P.16). Net Standby On Sets the network status for when the unit is in standby mode (& P.16). Bluetooth On Status Shows the connection status of the NETWORK jack. LAN MAC Address Shows MAC address. WiFi MAC Address Shows MAC address. Bluetooth Addr Confirms the Bluetooth address. *1 Only when the radio is played back MusicCast Info Shows the information on MusicCast. *2 CRX-N470D only SSID Confirms the SSID. Direct Info Shows the information for Wireless Direct. Network Name Shows the name of the unit that appears on the network. vTuner ID Confirms the vTuner ID. IP Address 0.0.0.0 Firmware Update Confirms the IP address. 45 En Sets Bluetooth. Initialize Set Resets to the factory default settings. Version Shows the firmware version of the unit. Update Network Updates the firmware of the unit (& P.22). Troubleshooting Refer to the table below when the unit does not function properly. If your problem is not listed below or if the instruction below does not help, turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. First, check that the connectors of each cable are securely inserted in to jacks on each device. Check also that the power cable is plugged into an outlet. General Problem The unit enters the standby mode soon after the power is turned on. The unit does not operate properly. No sound. Sound is heard from the speaker on one side only. Noise is heard. The power suddenly turns off. There is noise interference from digital or high-frequency equipment. The remote control does not work or does not function properly. Cause Solution The power cable is not properly connected. Connect the power cable firmly. The unit got a strong electric shock from an outside source, such as lighting or excessive static electricity. Hold down A on the front panel for more than 10 seconds to initialize and reboot the unit. (If the problem persists, unplug the power cable from the wall outlet and plug it again after 30 seconds or more.) No appropriate source has been selected. Select an appropriate source with INPUT on the front panel or the source buttons on the remote control (& P.10, 13). Speaker connections are not secure. Secure the connections (& P.14). The volume is minimum or mute. Turn up the volume. Source device or speakers are not connected properly. Connect the source device or speaker cables properly (& P.14, 27). If the problem persists, the cables may be defective. This unit is too close to digital or radio-frequency equipment. Move this unit away from such equipment. The audio cable between this unit and Source device is defective. Connect the audio cable firmly. If the problem persists, use another audio cable. The sleep timer may be set (& P.43). Turn on the unit and play the source again. Auto Power Standby function is activated. (& P.16). This unit is too close to the digital or high-frequency equipment. Place this unit farther away from such equipment. The remote control may be outside its operation range. Operate the remote control within its operation range (& P.16). The remote control sensor on this unit may be exposed to direct sunlight or strong lighting such as an inverter type fluorescent lamp. Change the orientation of lighting or the unit, or location of the unit. The battery may be worn out. Replace the batteries with new ones (& P.13). There are obstacles between the sensor of this unit and the remote control. Remove the obstacles. 46 En Troubleshooting Network Problem Cause Solution The network feature does not function. The network parameters (IP address) have not been obtained properly. Enable the DHCP server function of the router. In addition, in the [Network Config] of the option settings of the unit, set [DHCP] to [On]. If you want to configure the network parameters manually, check that you are using an IP address which is not used by other network devices in your network (& P.45). For details on how to set the router, contact the manufacturer of the router. Playback stops (songs cannot be played back continuously). There are unsupported files in the server. Remove the files (including image files or hidden files) which the unit does not support from the folder being played back. The media sharing setting is not correct. Configure the sharing setting and select the unit as a device to which music contents are shared (& P.35). Some security software installed on your PC is blocking the access of the unit to your PC. Check the setting of the security software installed in your PC. The unit and PC are not in the same network. Check the network connections and your router settings, and then connect the unit and the PC to the same network. The files are not supported by the unit or the media server. Use the file format supported by both the unit and the media server (& P.53). The selected Internet radio station is currently not available. There may be a network problem at the radio station, or the service may have been stopped. Try the station later or select another station. The selected Internet radio station is currently broadcasting silence. Some Internet radio stations broadcast silence at certain of times of the day. In this case, no sound is output even if the signal is received. Try the station later or select another station. Access to the network is restricted by the firewall settings of your network devices (such as the router). Check the firewall settings of your network devices. Internet radio can be played only when it passes through the port designated by each radio station. The port number varies depending on the radio station. The dedicated application for mobile devices does not detect the unit. The unit and mobile devices are not in the same network. Check the network connections and your router settings, and then connect the unit and the PC to the same network. Update of the firmware via network failed. The network connection is unstable. Try updating again after a while. Or update the firmware via USB memory device (& P.22). The unit does not detect the PC. The files in the PC cannot be viewed or played back. Internet radio cannot be played. 47 En Troubleshooting Problem The iPhone does not recognize the unit when using AirPlay. The unit cannot connect to the Internet via a wireless router (access point). Wireless network is not found. Cause Solution A multi-SSID supported router is used. The network separation function of the router may prevent the iPhone from accessing the unit. When connecting an iPhone, use SSID that can access the unit. The wireless router is turned off. Turn on the wireless router. The unit is placed too far from the wireless router. Place the unit and the wireless router closer to each other. There is an obstacle between the unit and the wireless router. Remove the obstacles. Wireless communication is interrupted by the electromagnetic waves emitted from a microwave oven or other wireless devices. When using the unit via wireless connection, place it away from devices emitting electromagnetic waves. Access to the network is restricted by the firewall settings of your wireless router. Check the firewall setting of the wireless router. Bluetooth Problem Cannot make the unit pair with a Bluetooth device. Cannot make a Bluetooth connection. Cause Solution The unit is turned off. Turn the unit on and perform the pairing (& P.25). The [Bluetooth] of the option settings is set to [Off]. Set it to [On]. Another Bluetooth device is connected. Terminate current Bluetooth connection, and perform pairing with the new device. This unit and the device are too far apart. Pair the unit and device within a distance of 10 m (33 ft). There is a device (microwave oven, wireless LAN, etc.) that outputs signals in the 2.4 GHz frequency band nearby. Move this unit away from the device that is emitting radio-frequency signals. A Bluetooth adapter, etc., that you want to pair with this unit has a passkey other than “0000.” Use a device whose passkey is “0000.” The Bluetooth device does not support A2DP. Perform pairing with a device which supports A2DP. The [Bluetooth] of the option settings is set to [Off]. Set it to [On]. Another Bluetooth device is connected. Terminate current Bluetooth connection, then establish a Bluetooth with that device again. The Bluetooth function of the device is turned off. Turn on the Bluetooth function of the device. The pairing information has been deleted. Delete the Bluetooth device's pairing information and perform pairing again. This unit is not registered on the device’s Bluetooth connection list. Perform pairing again (& P.25). 48 En Troubleshooting Problem No sound is produced, or the sound is interrupted during playback. Cause Solution The volume of the Bluetooth device is set too low. Turn up the volume of the Bluetooth device. The Bluetooth device is not set to send Bluetooth audio signals to the unit. Switch the output of Bluetooth audio signals of the Bluetooth device to the unit. The Bluetooth connection of the unit with the device has terminated. Perform Bluetooth connection operations again (& P.25). There is a device (microwave oven, wireless LAN, etc.) that outputs signals in the 2.4 GHz frequency band nearby. Move this unit away from the device that is emitting radio-frequency signals. This unit and the Bluetooth device are too far apart. Move the Bluetooth device to within 10 m (33 ft) of the unit. The Bluetooth function of the device is turned off. Turn on the Bluetooth function of the device. The Bluetooth device is not set to send Bluetooth audio signals to this unit. Check that the Bluetooth function of the Bluetooth device is set properly. Disc Problem Playback does not start after a disc is inserted. Some button operations do not work. Playback does not start (or stops immediately) after pressing on the unit or on the remote control. Cause Solution The disc inserted in the unit may not be supported. Use a disc supported by the unit (& P.52). The disc may be dirty. Wipe the disc clean (& P.52). The disc inserted in the unit may not be supported. Use a disc supported by the unit (& P.52). If the unit was moved from a cold to warm place, condensation may have formed on the disc reading lens. Wait for an hour or two until the unit adjusts to the room temperature, and try again. USB devices Problem The unit does not detect the USB device. Folders and files in the USB device cannot be viewed. Cause Solution The USB device is not connected to the USB jack securely. Turn off the unit, reconnect your USB device, and turn the unit on again (& P.24). A USB device in a format other than FAT16/32 format is used. Use a USB device with FAT16 or FAT32 format. The data in the USB device is protected by encryption. Use a USB device without an encryption function. 49 En Troubleshooting DAB reception (CRX-N470D only) Problem Cannot tune into any DAB stations. The initial scan operations are not successful and [Not Found] is shown on the front panel display. Cause Solution The initial scan operations were not performed. Perform the initial scan operations (& P.28). The DAB signals are too weak. Use the DAB Tune Aid feature to conform the best position of the antenna (& P.30). The positioning of the antenna is not optimal for DAB reception. Check with your dealer or WorldDMB online at http://www.worlddab.org for a listing of the DAB coverage in your area. There is no DAB coverage in your area. There is noise interference (e.g. hiss, crackle or jitter) The antenna needs to be repositioned. Readjust the position of the antenna (& P.15). The DAB signals are too weak. Use the DAB Tune Aid feature to conform the best position of the antenna (& P.30). The DAB station information is not shown or is inaccurate. The DAB station may be temporarily out of service, or the DAB station information is not provided by the DAB broadcaster. Contact the DAB broadcaster. FM reception Problem FM stereo reception is noisy. Automatic tuning does not work. Cause Solution The antenna is not connected properly. Make sure the antenna is connected properly and change the position of the antenna (& P.15). The radio station you selected may be far from your area, or the antenna input is poor. Use a commercially available outdoor antenna. For details, consult a specialist store. The radio station you selected may be far from your area, or the antenna input is poor. Use a commercially available outdoor antenna. For details, consult a specialist store. Use the manual tuning method (& P.31). Cannot select a preset radio station. The preset (memory) may have been erased. Preset radio stations again (& P.31, 32). There is distortion, and clear reception cannot be obtained even with a good FM antenna or an outdoor antenna. Multipath reflection or other radio interference may be occurring. Change the height, direction, or placement of the antenna. 50 En Troubleshooting Messages on the front panel display Message Cause Solution Access to the PC is denied. Configure the sharing settings and select the unit as a device to which music contents are shared (& P.35). The unit cannot access the USB device. Turn off the unit and reconnect your USB device. If the problem persists, try another USB device. There is a problem with the signal path from the network to the unit. Make sure your router and modem are turned on. Check the connection between the unit and your router (or hub) (& P.17). Initializing The unit is starting up. Wait until the message disappears. If the message stays more than 3 minutes, turn off the unit and turn it on again. Loading... The unit is loading the specified file/content. Wait until the unit finishes loading. No Content Selected folder does not contain playable files. Select a folder with playable files (& P.53). The disc inserted in the unit may not be supported. Use a disc supported by the unit (& P.52). The disc may be dirty, or foreign matter may be attached to it. Wipe the disc clean. Alternatively, remove foreign matter adhered to the disc. Access Denied Access Error No Disc Disc is set upside-down. Set the disc with the labeled side facing up. No Songs The disc does not contain playable files. Set a disc with playable files (& P.52). Not Connected The unit is not connected to the network. Check the network connection. The connected USB device is not supported by the unit. USB device is not connected properly. Disconnect the USB device, turn off the unit, and turn it on again. If this does not solve the problem for the USB device, it is not playable on the unit. Unable to play The unit cannot play back the songs stored on the USB devices or the computer for some reason. Check if the format of files you are trying to play is supported by the unit (& P.53). Version Error Firmware update has failed. Update the firmware again. Overcurrent 51 En Supported devices/media and file formats Supported devices/ media PCs Handling discs Discs • This unit is designed for use with audio CD, CD-R/RW (ISO 9660 format) with any of the following logos printed on the disc or the disc jacket. • Do not use a protective cover to prevent scratches. • Do not set foreign object on the disc tray. • Do not set more than one disc in this unit at one time. This could cause damage to both this unit and the discs. CD-R/RW* NAS NAS compatible with DLNA version 1.5. • The unit is compatible with USB mass storage class devices (e.g., flash memories or portable audio players) using FAT16/FAT32 format. * Discs which bear one of the following. FOR CONSUMER FOR CONSUMER USE FOR MUSIC USE ONLY • 8-cm discs are playable with this unit. Set a disc in the inner recessed area of the disc tray. • Do not connect devices other than the USB mass storage class devices (USB charger, USB hub, etc.), PCs, card readers, and external hard discs. Notes on discs • USB devices with encryption cannot be used. • CD-R/RW cannot be played back unless finalized. Finalization means the process for making a disc to be ready for playback on a compatible device . • Depending on the manufacturer or type of the USB device, the unit may not recognize the USB device or some functions may be unavailable. • Use a soft-tipped pen when writing on the label side of a disc. • Do not put tape, seal, glue, etc., on a disc. Audio CD PC with Windows Media Player 11 or Windows Media Player 12 installed. USB devices • Do not touch the surface of the disc. Hold a disc by its edge or center hole. • Do not set any other type of disc other than stated above in this unit. Doing so may damage the unit. • Some discs cannot be played back depending on the disc characteristics or recording conditions. • Do not use any non-standard shaped discs such as a heart-shaped disc. • Do not use discs with many scratches or a crack on their surface, or warped/glued discs. 52 En • If a disc becomes dirty, wipe it with a clean, dry soft cloth from the center out to the edge. Do not use record cleaner or paint thinner. • Do not use any lens cleaners as they may cause malfunction. • Do not expose discs to direct sunlight, high temperature, high humidity, or dust. • When a disc is not being used, remove it from this unit and store in an appropriate case. Supported devices/media and file formats File format File format the unit supporting is as follows. DLNA/USB Format Disc Sampling frequency (kHz) WAV 32/44.1/48/ 88.2/96/176.4/ 192 MP3 WMA * Quantization Bitrate bitrate (bit) (kbps) Number of channels Gapless playback supported 16/24 - 2 3 32/44.1/48 - 8-320 2 - 32/44.1/48 - 8-320 2 - MPEG-4 AAC 32/44.1/48 - 8-320 2 - FLAC 32/44.1/48/ 88.2/96/176.4/ 192 16/24 - 2 3 ALAC 32/44.1/48/ 88.2/96 16/24 - 2 3 AIFF 32/44.1/48/ 88.2/96/176.4/ 192 16/24 - 2 3 Format * Linear PCM format only • To play back FLAC files, you need to install server software that supports sharing of FLAC files via DLNA on your PC or use a NAS that supports FLAC files. • Digital Rights Management (DRM) files cannot be played back. 53 En Sampling frequency (kHz) Quantization bitrate MP3 8-48 16 WMA 16-48 16 Specifications Bluetooth Input AUX IN AUX 1 AUX 2 Stereo L/R: RCA 3.5 mm stereo mini jack Type Wave length Output power Semiconductor laser GaAs/GaAlAs 790 nm 7 mW CD, CD-R/RW Audio CD, MP3, WMA Bluetooth version Supported profile CD Laser Media Audio format Compatible codecs Operating modes Wireless output Maximum communication range Amplifier section Maximum output power Frequency response Total harmonic distortion USB Supported file format MP3, WMA, MPEG4 AAC, WAV, FLAC, ALAC, AIFF Network Headphones Interface Internet radio PC client function Supported file format AirPlay 100Base-TX/10Base-T vTuner service supported DLNA Ver. 1.5 (DMP/DMR function) supported Same as USB supported file format AirPlay supported Subwoofer output power Power supply/Frequency Power consumption Standby power consumption IEEE802.11 b/g/n 2.4 GHz WEP, WPA2-PSK (AES), Mixed Mode Dimensions (W × H × D) (with wireless antenna upright) Weight Tuner Preset memory Tuning range FM 30 U.S.A. and Canada models: 87.5 MHz to 107.9 MHz Other models: 87.5 MHz to 108.0 MHz DAB AC 100 to 240 V, 50/60 Hz 25 W Network standby off: 0.4 W Network standby on Wired (Ethernet): 1.8 W Wireless (Wi-Fi/Wireless Direct/Bluetooth): 1.9 W/1.9 W/1.7 W 270 × 110 × 330 mm (270 × 179 × 330 mm) 3.0 kg The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. DAB (CRX-N470D ONLY) Preset Memory Tuning range Compatibility 22 W + 22 W (6 Ω, 1 kHz, 10% THD) 20 Hz to 20 kHz (0±3 dB) ≤ 0.05 % (10 W/6 Ω 1 kHz) 500 mV/32 Ω Input: 1 kHz 300 mV, 32 Ω terminated 1.5 V/1 kΩ General Wi-Fi Wireless network standards Radio frequency Available security methods Ver. 2.1+EDR A2DP (Advanced Audio Distribution Profile) AVRCP (Audio/Video Remote Control Profile) SBC, AAC (AAC is Sink only) Sink or Source Bluetooth Class 2 10 m (33 ft) (without interference) 30 174 to 240 MHz (Band III) DAB/DAB+ 54 En Trademarks AirPlay, iPad, iPhone, iPod, iPod touch and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries. (For CRX-N470D) The unit supports DAB/DAB+ tuning. AirPlay works with iPhone, iPad, and iPod touch with iOS 4.3.3 or later, Mac with OS X Mountain Lion or later, and Mac and PC with iTunes 10.2.2 or later. (as of July 2015) Explanations regarding GPL This product utilizes GPL/LGPL open-source software in some sections. You have the right to obtain, duplicate, modify, and redistribute this open-source code only. For information on GPL/ LGPL open source software, how to obtain it, and the GPL/LGPL license, refer to the Yamaha Corporation website (http://download.yamaha.com/sourcecodes/musiccast/). DLNA™ and DLNA CERTIFIED™ are trademarks or registered trademarks of Digital Living Network Alliance. All rights reserved. Unauthorized use is strictly prohibited. Windows™ Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Internet Explorer, Windows Media Audio and Windows Media Player are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. Android™ The Wi-Fi Protected Setup Identifier Mark is a mark of the Wi-Fi Alliance. Android and Google Play are trademarks of Google Inc. Wi-Fi, Wi-Fi Alliance, Wi-Fi CERTIFIED, Wi-Fi Protected Setup, WPA and WPA2 are trademark or regitstered trademark of Wi-Fi Alliance. MusicCast is a trademark or registered trademark of Yamaha Corporation. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under license. Bluetooth protocol stack (Blue SDK) Copyright 1999-2014 OpenSynergy GmbH All rights reserved. All unpublished rights reserved. 55 En VAROITUS Muiden kuin tässä esitettyjen toimintojen säädön tai asetusten muutto saattaa altistaa vaaralliselle säteilylle tai muille vaarallisille toiminnoille. OBSERVERA Apparaten kopplas inte bort från växelströmskällan (nätet) så länge som den är ansluten till vägguttaget, även om själva apparaten har stängts av. DK Advarsel: Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå utsættelse for stråling. Bemærk: Netafbryderen A er sekundært indkoblet og ofbryder ikke strømmen fra nettet. Den indbyggede netdel er derfor tilsluttet til lysnettet så længe netstikket sidder i stikkontakten. ADVARSEL Netspæendingen til dette apparat er IKKE afbrudt, sålæenge netledningen siddr i en stikkontakt, som er t endt - også selvom der or slukket på apparatets afbryder. VAROITUS Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta. N Observer: Nettbryteren A er sekundert innkoplet. Den innebygdenetdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten. S Klass 1 laseraparat Varning! Om apparaten används på annat sättþän i denna bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1. Observera! Strömbrytaren A är sekundärt kopplad och inte bryter inte strömmen från nätet. Den inbyggda nätdelen är därför ansluten till elnätet så länge stickproppen sitter i vägguttaget. SF Luokan 1 laserlaite Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja roiskevedelle. Huom. Toiminnanvalitsin A on kytketty toisiopuolelle, eikä se kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon aina silloin, kun pistoke on pistorasiassa. VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄ TEESEEN. ALTTIINA VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN. 56 En AVEEA71102A Important Notice: Guarantee Information for customers in EEA* and Switzerland English For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland warranty service, please either visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your country. * EEA: European Economic Area http://europe.yamaha.com/warranty/ Yamaha Global Site http://www.yamaha.com/ Yamaha Downloads http://download.yamaha.com/ Manual Development Group © 2016 Yamaha Corporation Published 06/2016 NV-A0 CRX-N470OM/EN