Arcair SLICE® NEW Exothermic Cutting Equipment Manual de usuario

Marca: Arcair

Modelo: SLICE® NEW Exothermic Cutting Equipment

Tipo: Manual de usuario

SAFETY AND

OPERATING

INSTRUCTIONS

SLICE

EXOTHERMIC

CUTTING EQUIPMENT

English

French

Spanish

Italian

SLICE

TORCH

SLICE

PACKAGE

SLICE

STRIKER

Art# A-13635

Revision: AC Issue Date: 24-01-2019 Manual No.: 89250840

WE APPRECIATE YOUR BUSINESS!

Congratulations on your new Arcair

product. We are proud to have you as our customer and

will strive to provide you with the best service and support in the industry. This product is

backed by our extensive warranty and world-wide service network. To locate your nearest

distributor or service agency visit us on the web at www.esab.com/arcair.

This Manual has been designed to instruct you on the correct installation and use of your Arcair

product. Your satisfaction with this product and its safe operation is our ultimate concern.

Therefore, please take the time to read the entire manual, especially the Safety Precautions.

They will help you to avoid potential hazards that may exist when working with this product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

Arcair is a Global Brand of cutting Products for ESAB. We manufacture and supply to major

welding industry sectors worldwide including; Manufacturing, Construction, Mining, Automotive,

Aerospace, Engineering, Rural and DIY/Hobbyist.

We distinguish ourselves from our competition through market-leading, dependable products

that have stood the test of time. We pride ourselves on technical innovation, competitive prices,

excellent delivery, superior customer service and technical support, together with excellence

in sales and marketing expertise.

Above all, we are committed to develop technologically advanced products to achieve a safer

working environment within the welding industry.

WARNING

Read and understand this entire Manual and your employer’s safety

practices before installing, operating, or servicing the equipment.

While the information contained in this Manual represents the Manu-

facturer's best judgment, the Manufacturer assumes no liability for its

use.

SLICE

Exothermic Cutting Equipment

Safety and Operating Instructions

Manual Number: 89250840

Published by:

ESAB Group Inc.

2800 Airport Rd.

Denton, TX. 76208

(940) 566-2000

www.esab.com/arcair

U.S. Customer Care: (800) 426-1888

International Customer Care: (940) 381-1212

Reproduction of this work, in whole or in part, without written permission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage

caused by any error or omission in this Manual, whether such error results from negligence, accident,

or any other cause.

For Printing Material Speciﬁcation in the Americas refer to document 47X1920

For Printing Material Speciﬁcation in Europe refer to document 47X1953

Publication Date: 08-03-2018

Revision Date: 24-01-2019

Record the following information for Warranty purposes:

Where Purchased:

Purchase Date:

Be sure this information reaches the operator.

You can get extra copies through your supplier.

CAUTION

These INSTRUCTIONS are for experienced operators. If you are not fully familiar

with the principles of operation and safe practices for arc welding and cutting equip-

ment, we urge you to read our booklet, "Precautions and Safe Practices for Arc

Welding, Cutting, and Gouging," Form 52-529. Do NOT permit untrained persons to

install, operate, or maintain this equipment. Do NOT attempt to install or operate this

equipment until you have read and fully understand these instructions. If you do not

fully understand these instructions, contact your supplier for further information. Be

sure to read the Safety Precautions before installing or operating this equipment.

USER RESPONSIBILITY

This equipment will perform in conformity with the description thereof contained in this manual and accompanying labels and/

or inserts when installed, operated, maintained and repaired in accordance with the instructions provided. This equipment must

be checked periodically. Malfunctioning or poorly maintained equipment should not be used. Parts that are broken, missing,

worn, distorted or contaminated should be replaced immediately. Should such repair or replacement become necessary, the

manufacturer recommends that a telephone or written request for service advice be made to the Authorized Distributor from

whom it was purchased.

This equipment or any of its parts should not be altered without the prior written approval of the manufacturer. The user of this

equipment shall have the sole responsibility for any malfunction which results from improper use, faulty maintenance, damage,

improper repair or alteration by anyone other than the manufacturer or a service facility designated by the manufacturer.

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR

OPERATING.

PROTECT YOURSELF AN D OTHERS!

iii

ASSUREZ-VOUS QUE CE DOCUMENT D’INFORMATION EST DISTRIBUÉ À L’OPÉRATEUR.

DES COPIES SUPPLÉMENTAIRES SONT DISPONIBLES CHEZ VOTRE FOURNISSEUR.

MISE EN GARDE

Les INSTRUCTIONS suivantes sont destinées aux opérateurs qualiés seulement.

Si vous n’avez pas une connaissance approfondie des principes de fonctionnement

et des règles de sécurité applicables au soudage à l’arc et à l’équipement de

coupage, nous vous suggérons de lire notre brochure « Précautions et pratiques

de sécurité pour le soudage à l’arc, le coupage et le gougeage », Formulaire 52-

529. Ne permettez PAS aux personnes non qualiées d’installer, d’utiliser ou

d’effectuer des opérations de maintenance sur cet équipement cet équipement. Ne

tentez PAS d’installer ou d’utiliser cet équipement avant d’avoir lu et bien compris

ces instructions. Si vous ne comprenez pas bien les instructions, renseignez-vous

auprès de votre fournisseur. Assurez-vous de lire les Règles de Sécurité avant

d’installer ou d’utiliser cet équipement.

RESPONSABILITÉS DE L’UTILISATEUR

Cet équipement fonctionnera conformément à la description contenue dans ce manuel, les étiquettes d’accompagnement et/

ou les feuillets d’information à condition d’être installé, utilisé, entretenu et réparé selon les instructions fournies. L’équipement

doit être contrôlé de manière périodique. Ne jamais utiliser un équipement qui ne fonctionne correctement bien ou n’est pas

bien entretenu. Les pièces qui sont brisées, usées, déformées ou contaminées doivent être remplacées immédiatement. Dans

le cas où une réparation ou un remplacement est nécessaire, e fabricant recommande de faire une demande de conseil de

service écrite ou par téléphone auprès du distributeur agréé où l’équipement a été acheté.

Cet équipement ou ses pièces ne doivent pas être modiés sans permission préalable écrite du fabricant. L’utilisateur de

l’équipement sera le seul responsable de toute défaillance résultant de toute utilisation, maintenance, réparation incorrectes,

de dommages ou encore de modication apportées par une personne autre que le fabricant ou un centre de service désigné

par ce dernier.

ASSUREZ-VOUS DE LIRE ET DE COMPRENDRE LE MANUEL D’UTILISATION AVANT

D’INSTALLER OU D’UTILISER L’UNITÉ.

PROTÉGEZ-VOUS ET LES AUTRES!

DECLARATION OF CONFORMITY

According to

The Low Voltage Directive 2014/35/EU, entering into force 20 April 2016

The EMC Directive 2014/30/EU, entering into force 20 April 2016

The RoHS Directive 2011/65/EU, entering into force 2 January 2013

Type of equipment

EXOTHERMIC CUTTING SYSTEM

Type designation etc.

SLICE Exothermic Torch Cutting System

Brand name or trade mark

Arcair SLICE

Manufacturer or his authorised representative

Name, address, telephone No:

ESAB Group Inc.

2800 Airport Rd

Denton TX 76207

Phone: +01 800 426 1888, FAX +01 603 298 7402

The following harmonised standard in force within the EEA has been used in the

design:

IEC/EN 60974-11:2010 Arc Welding Equipment Part II: Electrode Holders

IEC/EN 60974-10:2014 + AMD 1:2015 Published 2015-06-19 Arc Welding Equipment - Part

10: Electromagnetic compatibility (EMC) requirements

Additional Information: Restrictive use, Class A equipment, intended for use in location

other than residential.

By signing this document, the undersigned declares as manufacturer, or the

manufacturer’s authorised representative, that the equipment in question complies

with the safety requirements stated above.

Date Signature Position

15 September, 2016

Flavio Santos General Manager

Accessories and Adjacencies

2018

Table of Contents

SECTION 1: INTRODUCTION ........................................................................................1

1.01 How to Use this Manual ............................................................1

1.02 Receipt of Equipment ................................................................1

1.03 Description ...............................................................................1

SECTION 2: SAFETY PRECAUTIONS ...........................................................................2

SECTION 3: PROCESS FUNDAMENTALS .....................................................................5

SECTION 4: EQUIPMENT .............................................................................................6

4.01 SLICE Torch ..............................................................................6

4.02 SLICE Striker ............................................................................6

4.03 SLICE Packs .............................................................................6

4.04 Cutting Rods ............................................................................. 7

4.05 SLICE Components ...................................................................8

4.06 Charging the Ignition Source .....................................................9

SECTION 5: CUTTING DATA ......................................................................................10

5.01 Material Cutting Rates ............................................................10

5.02 Cutting Electrode Types ..........................................................11

5.03 SLICE Cutting Torches .............................................................11

SECTION 6: OPERATION ............................................................................................12

6.01 Cutting without Power ............................................................12

6.02 Cutting with Power .................................................................13

6.03 Hole Piercing ..........................................................................14

6.04 Copper and Copper Alloys ....................................................... 15

SECTION 7: IMPORTANT PROCESS VARIABLES .......................................................16

7.01 Oxygen Pressure.....................................................................16

7.02 Amperage ...............................................................................17

7.03 Travel Speed ...........................................................................17

7.04 Electrode-To-Work Angle ........................................................17

SECTION 8: APPLICATIONS ......................................................................................18

SECTION 9: TROUBLESHOOTING ..............................................................................19

9.01 General troubleshooting ..........................................................19

9.02 Ignition source led display guide ............................................. 20

SECTION 10: PARTS LISTING ....................................................................................22

SECTION 11: STATEMENT OF WARRANTY ................................................................25

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

This Page Intentionally Blank

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 1: INTRODUCTION

1.01 How to Use this Manual

To ensure safe operation, read the entire manual, including the chapter on safety instructions and

warnings.

Throughout this manual, the words WARNING, CAUTION, and NOTE may appear. Pay particular

attention to the information provided under these headings. These special annotations are easily

recognized as follows:

NOTE!

An operation, procedure, or background information which requires

additional emphasis or is helpful in efcient operation of the system.

CAUTION

A procedure which, if not properly followed, may cause damage to the

equipment.

WARNING

A procedure which, if not properly followed, may cause injury to the

operator or others in the operating area.

WARNING

Gives information regarding possible electrical shock injury. Warnings

will be enclosed in a box such as this.

1.02 Receipt of Equipment

When you receive the equipment, check it against the invoice to make sure it is complete and

inspect the equipment for possible damage due to shipping. If there is any damage, notify the carrier

immediately to ﬁle a claim. Furnish complete information concerning damage claims or shipping

errors to the location in your area, listed on the back cover of this manual. Include a full description

of the parts in error.

If you want additional or replacement copies of this manual, please contact Arcair at the address

and phone number in your area listed on the inside back cover of this manual. Include the Manual

number (Page i).

1.03 Description

Arcair

SLICE

systems can cut, burn or pierce almost any metallic, non-metallic or composite

material. The SLICE exothermic torch cuts right through hard-to-cut materials such as mild, stainless

and alloy steels, cast iron, aluminum, magnesium and other non-ferrous metals, slag and refractory

materials, and concrete or brick.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 2: SAFETY PRECAUTIONS

WARNING

SERIOUS INJURY OR DEATH may result if welding and cutting equipment

is not properly installed, used, and maintained. Misuse of this equipment

and other unsafe practices can be hazardous. The operator, supervisor, and

helper must read and understand the following safety warnings and instruc-

tions before installing or using any welding or cutting equipment, and be

aware of the dangers of the welding or cutting process. Training and proper

supervision are important for a safe work place. Keep these instructions for

future use. Additional recommended safety and operating information is refer-

enced in each section.

WARNING

This product contains chemicals, including lead, or otherwise produces

chemicals known to the State of California to cause cancer, birth defects

and other reproductive harm. Wash hands after handling.

ELECTRIC SHOCK CAN CAUSE INJURY OR DEATH

The purchaser is responsible for the safe installation, operation, and use of all products

purchased, including compliance with all applicable ISO standards and local codes in

the country of use. Do not service or repair equipment with power on. Do not operate

equipment with protective insulators or covers removed. Service or repair to equipment

must be done by qualiﬁed and/or trained personnel only.

Do not contact electrically live parts. Always wear dry welding gloves that are in good condition.

Aluminized, protective clothing can become part of the electrical path. Keep oxygen cylinders, chains,

wires, ropes, cranes, and hoists away from any part of the electrical path. All ground connections must

be checked periodically to determine if they are mechanically strong, and electrically adequate for the

required current. When engaged in AC welding/cutting under wet conditions or where perspiration

is a factor, the use of automatic controls for reducing the no load voltage is recommended to reduce

shock hazards. Accidental contact must be prevented when using open circuit voltage exceeding 80

volts AC, or 100 volts DC by adequate insulation or other means. When welding is to be suspended for

any length of time, such as during lunch or overnight, all electrode holders and electrodes should be

removed from the electrode holder and the power supply should be turned off to prevent accidental

contact. Keep MIG Guns, electrode holders, TIG torches, Plasma torches, and electrodes away from

moisture and water. See safety and operating references 1, 2, and 8.

SMOKE, FUMES, AND GASES CAN BE DANGEROUS TO YOUR HEALTH

Ventilation must be adequate to remove smoke, fumes, and gases during operation to

protect operators and others in the area. Vapors of chlorinated solvents can form the

toxic gas "Phosgene" when exposed to ultraviolet radiation from an electric arc. All

solvents, degreasers, and potential sources of these vapors must be removed from the

operating area. Use air-supplied respirators if ventilation is not adequate to remove all

fumes and gases. Oxygen supports, and vigorously accelerates ﬁre and should never be used for

ventilation. See safety and operating references 1, 2, 3, and 4.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

ARC RAYS, HOT SLAG, AND SPARKS CAN INJURE EYES AND BURN SKIN

Welding and cutting processes produce extreme localized heat and strong ultraviolet

rays. Never attempt to weld/cut without a federally compliant welding helmet with the

proper lens. A number 12 to 14 shade ﬁlter lens provides the best protection against arc

radiation. When in a conﬁned area, prevent the reﬂected arc rays from entering around

the helmet. Approved shielding curtains and appropriate goggles should be used to

provide protection to others in the surrounding area. Skin should be protected from arc rays, heat, and

molten metal. Always wear protective gloves and clothing. All pockets should be closed and cuffs sewn

shut. Leather aprons, sleeves, leggings, etc. should be worn for out-of-position welding and cutting, or

for heavy operations using large electrodes. Hightop work shoes provide adequate protection from foot

burns. For added protection, use leather spats. Flammable hair preparations should not be used when

welding/cutting. Wear ear plugs to protect ears from sparks. Where work permits, the operator should

be enclosed in an individual booth painted with a low reﬂective material such as zinc oxide. See safety

and operating references 1, 2, and 3.

WELDING SPARKS CAN CAUSE FIRES AND EXPLOSIONS

Combustibles reached by the arc, ﬂame, ﬂying sparks, hot slag, and heated materials can

cause ﬁre and explosions. Remove combustibles from the work area and/or provide a ﬁre

watch. Avoid oily or greasy clothing as a spark may ignite them. Have a ﬁre extinguisher

nearby, and know how to use it. If welding/cutting is to be done on a metal wall, partition,

ceiling, or roof, precautions must be taken to prevent ignition of nearby combustibles on the other side.

Do not weld/cut containers that have held combustibles. All hollow spaces, cavities, and containers

should be vented prior to welding/cutting to permit the escape of air or gases. Purging with inert gas is

recommended. Never use oxygen in a welding torch. Use only inert gases or inert gas mixes as required

by the process. Use of combustible compressed gases can cause explosions resulting in personal injury

or death. Arcing against any compressed gas cylinder can cause cylinder damage or explosion. See

safety and operating references 1, 2, 5, 7, and 8.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SAFETY AND OPERATING REFERENCES

1. Code of Federal Regulations (OSHA) Section 29, Part 1910.95, 132, 133, 134, 139, 251, 252,

253, 254 and 1000. U.S. Government Printing Ofﬁce, Washington, DC 20402.

2. ANSI Z49.1-2012 "Safety in Welding, Cutting, and Allied Processes".

3. ANSI Z87.1-2015 "American National Standard for Occupational and Educational Personal

Eye and Face Protection Devices".

4. ANSI/ASSE Z88.2-2015 "American National Standard Practices for Respiratory Protection".

American National Standards Institute Inc., 1430 Broadway, New York, NY 10018.

5. AWS F4.1:2017. "Safe Practices for the Preparation of Containers and Piping for Welding,

Cutting, and Allied Processes"

6. AWS C5.3:2000 (R2011) "Recommended Practices For Air Carbon Arc Gouging And Cutting".

American Welding Society, 8669 NW 36 Street, PO Box 130, Miami, Florida 33166-6672

7. NFPA 51B:2014 "Standard for Fire Prevention During Welding, Cutting, and Other Hot Work"

National Fire Protection Association (NFPA), 1 Batterymarch Park, Quincy, Massachusetts,

USA 02169-7471

8. NFPA-70:2017 "National Electrical Code". National Fire Protection Association (NFPA), 1

Batterymarch Park, Quincy, Massachusetts, USA 02169-7471

9. CAN/CSA-W117.2-12 (R2017) "Safety in Welding, Cutting and Allied Processes". Canadian

Standards Association, 178 Rexdale Blvd., Rexdale, Ontario, Canada M9W 1R3.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 3: PROCESS FUNDAMENTALS

The SLICE Exothermic Cutting process uses an exothermic chemical reaction that burns, melts or

vaporizes most materials. The reaction begins with an electrical arc or alternate energy source that

causes a steel cutting rod to burn. Oxygen ﬂows through the center of the rod.

Because of the rod’s design, the burning makes excess heat ("exo - thermic") which cuts the

workpiece. Once started, the burn will continue as long as oxygen ﬂows through the rod. The heat

created melts the material being cut. The velocity of oxygen through the rod blows the molten material

away, creating the kerf or cut line.

This arc ignition process led to invention of the oxy-arc torch and design of equipment for underwater

construction and salvage.

The electrical arc that starts the burn can be from a welding power source that delivers at least 100

amps, a 12-volt lead acid or similar low-impedance battery. The cutting process can run without

power, using the heat of the reaction only, or with power, cutting with an electrical arc from a welding

power source providing more heat.

HISTORY

The exothermic cutting rod is a small oxygen lance. A prime example of the combustion triangle is one

side being fuel (the steel lance); the oxygen source (pure oxygen being forced through the lance); the

heat of combustion (some external source of heat). However, when the lance pierces a slag puddle,

the puddle becomes the source of heat until the lance is withdrawn, at which time burning stops.

In 1888, a published paper described passing oxygen through a steel tube and heating the tube to

a bright red. Heat resulted. In 1901, Ernst Henner ﬁled a German patent on an early oxygen lance

made of two concentric tubes. In 1902, documentation shows that the oxygen lance replaced oil

and gas torches for opening furnace taps in steel blast furnaces. The oxygen lance has since been

used to cut rocks and concrete structures. An example is cutting up reinforced concrete structures

such as bunker emplacements and tank traps built in Europe during World War II.

An ideal way to start the lance, workers found, was to use a welding power source on conductive

material to strike an arc and start the burn. This process worked well in construction, even in mud

and water.

Around 1940, the burning bar or exothermic lance was ﬁrst marketed as a cutting tool. A ﬂexible

version made of an insulated cable was introduced around 1960. Not until the early 1980’s were

smaller burning bars designed for hand torch use, above and below water. A one-piece unit now

allows for adequate rod surface exposure to an oxygen supply for exothermic cutting. Arcair, an ESAB

brand, is a world leader in metal removal and cutting and sells this exothermic cutting equipment

under the trade name Arcair SLICE.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 4: EQUIPMENT

4.01 SLICE Torch

The SLICE Torch, a gun-shaped tool, provides a means of gripping the rod and supplying the oxygen

and power to the cutting rod. The basic torch includes 10 ft. (3.05 m) of power cable and oxygen

hose. The power cable can carry 200 amps in a power cutting operation. The oxygen hose includes

a standard size oxygen ﬁtting and is ready to be connected to the user’s oxygen regulator. This

standard torch has a ﬂexible hand shield which is easily replaceable if damaged, plus the torch is

molded from a super tough Thermo plastic.

An optional 6" (152 mm) collet extension and 6" (152 mm) diameter extension shield is available

to help reduce torch wear or damage when piercing. Also available is a 3/8" (9.5 mm) adapter kit

consisting of a collet chuck, Collet Nut, washer, and ﬂashback arrestor needed to adapt the torch for

using the 3/8" (9.5 mm) diameter cutting rods.

4.02 SLICE Striker

A SLICE Striker is available for cutting without power. The striker is an insulated piece of copper

plate with a serrated surface. By scratching the rod against the copper plate an arc is initiated and

the cutting process begins. Striker wear can be extended by using the smallest exposed portion of

the copper plate and gradually increasing.

SLICE Striker

1” open

SLICE Striker

2” open

SLICE Striker

Full open

The SLICE striker comes standard with a 10 ft. (3.05 m) cable.

4.03 SLICE Packs

SLICE

Utility Pack

Includes a rugged carrying case. Power connections (12 volt battery only), tong style

battery clamps makes power connection quick and easy. Industrial oxygen hose

connected to the torch; industry standard Oxygen hose supplies the torch with oxygen

and standard ﬁttings used to connect to oxygen regulators.

SLICE

Battery Pack

Includes a rugged carrying case. Power connections twist-lock style connection;

easy to connect to battery ignition source for both torch and striker and color coded

connectors. Industrial oxygen hose connected to the torch; industry standard Oxygen

hose supplies the torch with oxygen, standard ﬁttings used to connect to oxygen

regulators, and color coded connections.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SLICE

Industrial Pack

Versatility for industrial type applications. Industrial cart capable of carrying a 9"

diameter oxygen cylinder. Packed with the basic items needed to do a cutting job; SLICE

Torch Assembly - 10 ft leads, striker assembly, oxygen regulator, battery charger, and

cutting rod holder. Industrial oxygen hose connected to the torch; industry standard

Oxygen hose supplies the torch with oxygen and standard ﬁttings used to connect to

oxygen regulators.

SLICE

Complete Pack

Rugged aluminum carrying case; packed with the basic items needed to do a

cutting job. Self-contained cutting system lends itself well to the emergency

type cutting situations where seconds count. Complete unit weights 70

lbs (31.75 kg). Storage compartment with hinged door for parts storage

during transportation. Power connections twist-lock style connection; easy

to connect to battery ignition source assembly for both torch and striker

and color coded connectors. Industrial oxygen hose connected to the torch;

industry standard Oxygen hose supplies the torch with oxygen. Standard

ﬁttings used to connect to oxygen regulators.

4.04 Cutting Rods

SLICE Cutting Rods are made of carbon steel, by rolling a steel strip into a rod, and are coated or

uncoated. The coating is made of arc stabilizers and a binder. Several advantages to using the

coated rods with power include:

• More efﬁcient cutting rates (more cut per inch of rod burnt and more cut per minute of burn time)

• Easier rod operation

• Protection from burning out on the side of the rod, especially when piercing

Rod Size Uses

1/4" x 22"

6.4 mm x 558.8 mm

Standard size cutting rods used in a variety of jobs. Recommended for

all straight-line cutting and most general-cutting applications. Coated

or uncoated.

1/4" x 44"

6.4 mm x 1117.6 mm

Used when greater length is needed to reach the cutting area or when

piercing holes in materials thicker than 18" (457,2 mm). Uncoated.

3/8" x 18"

9.5 mm x 457.2 mm

Used for heavy piercing with a large bore. Coated or uncoated.

3/8" x 36"

9.5 mm X 914.4 mm

Used when added length is needed to complete cutting. Uncoated.

NOTE!

All SLICE cutting torches come ready to use the 1/4" (6.4 mm) diameter

rods. Use of the 3/8" (9.5 mm) diameter rods requires the 3/8" (9.5 mm)

conversion kit, Part Number 94-463-032.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

4.05 SLICE Components

Art# A-13635

Figure 1: SLICE Torch

SLICE Torch

Oxygen Valve Lever

Oxygen Hose

Connection

Torch Cable

Power Assisted Torch End

Collet Nut

Black Male Connector

Striker Cable

SLICE Striker

Art# A-13637

Red Male Connector

Figure 2: SLICE Torch and Striker

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

Art # A-13638

FAULT CHARGING CHARGED

STRIKER

TEST

TORCH

22-30V

Cam Lock Female

Terminal F/ Torch

Cam Lock Female

Terminal F/ Striker

Test Button

DC Input

Fault / Charge Status Gauge

CAUTION

THIS UNIT CONTAINS A LEAD ACID BATTERY WHICH RELEASES EXPLOSIVE

HYDROGEN GAS WHEN BEING CHARGED. CHARGE THIS BATTERY ONLY IN A

VENTILATED LOCATION DESIGNATED AS A LEAD-ACID BATTERY CHARGING

AREA. DO NOT CHARGE THIS BATTERY WHILE OPERATING THIS TORCH.

Figure 3: SLICE Battery Ignition Source

4.06 Charging the Ignition Source

There are 3 LEDs on the Ignition Source panel (FAULT, CHARGING, and CHARGED). Fully charged

status will display all LEDs green. For explanation of LED readouts refer to Section 9.2 Ignition Source

LED Display Guide. The AC/DC Power Adapter (p/n 96-076-043) is required to complete these steps.

NOTE!

It is recommended that the unit be recharged after every use or when-

ever the Charge Status LEDs shows 50% or less.

Charging the Ignition Source:

1. Press the TEST button on the Ignition Source panel to check status. If the LEDs do not present

all green LEDs then proceed with the steps below.

2. Insert the AC/DC Power Adapter Output connector into the DC Input socket on the Ignition Source

panel and plug the Power Adapter input cord into a 120 V, 60Hz or 240 V 50Hz wall outlet.

3. Keep the unit plugged in until fully charged. Charging time can be between 2-5 hours. On the

Ignition Source panel amber LEDs will display when fully charged.

4. Disconnect the AC/DC Power Adapter connector from the Ignition Source and push the Test

button to conﬁrm full charge status. All the LEDs will display green.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 5: CUTTING DATA

The following chart helps determine the best settings for a speciﬁc use as a result of extensive

laboratory testing of the SLICE Equipment to determine the best cutting rates. Actual cutting results

obtained in the ﬁeld vary due to conditions and experience of the user. Various usages of SLICE

Equipment return various results. Adjust the settings for any use. Use the following chart as a guide.

Oxygen pressure of 80 psi (551.6 kPa) achieves the best cutting. Some operations may require higher

or lower oxygen pressures - minimum 40 psi (275.8 kPa); maximum 100 psi (689.5 kPa). Amperage

over 200 amps does not improve cutting speed.

Find the right metal and thickness. For composites or unlisted metals, locate the listed type that most

resembles the material to be cut.

NOTE!

All these cutting values are based on 1/4" (6.4 mm) diameter ux-

coated rods. Cutting rates with 1/4" (6.4 mm) bare rods are slightly

less than the values listed in the chart.

5.01 Material Cutting Rates

Material Type Material Thickness

Length of Cut per

Inch Rod Used

Cutting Speed

in(mm) in(cm) in/min cm/min

Carbon Steel

1/8 (3.2) 2.25 (5.7) 72 183

1/4 (6.4) 1.5 (3.8) 52 132

3/8 (9.5) 1.38 (3.5) 42 106

1/2 (12.7) 1.25 (3.2) 35 89

3/4 (19.1) .75 (1.9) 22 56

Stainless

1/8 (3.2) 2.0 (5.1) 65 165

1/4 (6.4) 1.13 (2.9) 36 91

Aluminum

1/4 (6.4) 1.75 (4.4) 58 147

3/8 (9.5) 1.25 (3.2) 38 97

3/4 (19.1) .75 (1.9) 23 58

SAMPLE SELECTIONS:

The approximate cut/inch rod x amount of cut per rod = cut per rod used

Data: Cutting 3/8" (9.5 mm) aluminum with 1/4" (6.4 mm) ﬂuxed rod

1.25" (3.2 cm) x 19" (48.3 cm) = 23.8" (60.5 cm). Approximate cut/min arc time = 38" (97 cm)

Data: Cutting 1/4" (6.4 mm) carbon steel with 1/4" ﬂuxed rod

1.5" (3.8 cm) x 19" (48.3 cm) = 28.5" (72.4 cm). Approximate cut/min arc time = 52" (132 cm)

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

5.02 Cutting Electrode Types

Cutting rates in this chart were obtained using 80 PSI (551.6 kPa) oxygen pressure and 1/4" x 22"

(6.4 mm x 559 mm) cutting rods. These rates are averaged values based on multiple cutting tests.

Actual cutting rates may vary due to parameters used and operator expertise.

Part No.

Diameter

in(mm)

Length

in(mm)

Coated or

Uncoated.

Package

Quantity

Oxygen

Flow Rate

CFM(CMM)

Burn

Time

(sec)

42-049-002 1/4 (6.4) 22 (559) Coated 25 7.5 (.21) 40-45

42-049-003 1/4 (6.4) 22 (559) Coated 100 7.5 (.21) 40-45

43-049-002 1/4 (6.4) 22 (559) Uncoated 25 7.5 (.21) 40-45

43-049-003 1/4 (6.4) 22 (559) Uncoated 100 7.5 (.21) 40-45

43-049-005 1/4 (6.4) 44 (1117) Uncoated 25 7.5 (.21) 80-90

42-049-005 3/8 (9.5) 18 (457) Coated 50 12 (.34) 30-35

43-049-007 3/8 (9.5) 18 (457) Uncoated 50 12 (.34) 30-35

43-049-009 3/8 (9.5) 36 (914) Uncoated 25 12 (.34) 60-70

5.03 SLICE Cutting Torches

Part No.

Cable

Size

Power Cable

Length ft(m)

Oxygen

Hose Length

ft(m)

Cutting with

Power

Cutting without

Power

03-003-010 #1

10 (3.05) 10 (3.05)

Recommended Can Be Used

03-003-011 #6 Limited Use Only Recommended

03-003-012 #10 Not Recommended Recommended

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 6: OPERATION

SLICE Exothermic Cutting uses heat from a chemical reaction between a consumable steel rod and

oxygen ﬂowing through the rod. Test data show that little or no oxygen remains. The oxygen not

used in the reaction blows the molten material out of the cut area. This action creates the kerf that

allows cut progression.

6.01 Cutting without Power

Cutting without power uses the heat reaction from the rod and the oxygen to cut. To initiate this type

of cutting, ignite the rod from a spark supplied by a 12-volt battery or by a welding power source

capable of delivering a 100-amp surge. Once this spark has ignited the rod, the electrical path is

broken and the heat of the reaction melts the material and cuts it.

Battery

+ -

SLICE Torch

Striker

Oxygen Supply

Art# A-13639

Figure 4: Cutting without Power

Cutting without power can be done in remote areas. Support equipment and bulky power sources

are not needed.

1. Connect the torch to either terminal of a 12-volt battery or constant-current welding power

source, then connect the striker or a strike plate to the other terminal. If using a welding

power source, set output level for 100 amps.

2. Turn ON the oxygen supply and adjust the regulator to the proper working pressure. Insert

the cutting rod into the collet and tighten the Collet Nut.

3. Tap the cutting rod on a hard, ungrounded surface to seat the rod in the torch.

4. Depress the torch oxygen valve lever and check for oxygen leaks around the Collet Nut.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

NOTE!

If oxygen is leaking, repeat the procedure until no oxygen is leaking.

5. Put the torch in one hand and striker in the other. Depress the oxygen lever and touch the

cutting rod to the striker.

6. Once the rod is ignited, remove the striker, then move the burning rod to the workpiece and

begin cutting.

NOTE!

Hold the cutting rod at a 45° to 80° drag angle from the workpiece

surface. The angle depends on the thickness and type of material

being cut.

7. Make slight contact between the burning rod tip and the workpiece as the cut progresses.

This placement requires two motions:

a. Inward towards the workpiece as the rod is consumed

b. In the direction of cut

Use a protective lens shade #5 since there is no electrical arc.

6.02 Cutting with Power

Cutting with power requires an electrical arc from a welding power supply and increases the heat

created exothermically. Almost all constant-current welding power supplies can be used in powered

exothermic cutting. Cutting with power is faster than cutting without power.

Art# A-13111_AB

SLICE Torch

Oxygen Supply

Work Piece

Ground Clamp

Power Supply

Figure 5: Cutting with Power

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

CAUTION

Constant-voltage power supplies should not be used with exothermic cut-

ting equipment. When the exothermic cutting rod contacts the workpiece,

the power supply is dead shorted, causing maximum amperage output of

the power supply. This surge can exceed the rated output of the machine

and the recommended amperage for powered exothermic cutting.

1. Connect the torch to one terminal, then connect a welding ground clamp to the other terminal

of a CC (Constant Current) welding power source.

2. Attach the ground clamp to the workpiece. Unlike other processes, this process uses either

a welding power source set for DCEP (reverse polarity) or DCEN (straight polarity). AC

(alternating current) power supplies can also be used without affecting cutting performance.

Do not cut with power using a constant-potential power source.

3. Insert the cutting rod into the collet and tighten. Start the oxygen ﬂow, touch the rod tip to

the workpiece, and begin cutting. Hold the cutting rod at a 45° to 80° drag angle from the

workpiece surface.

4. Depress the torch oxygen valve lever and check for oxygen leaks around the Collet Nut.

5. As the cut proceeds, make slight contact between the burning rod and the workpiece. This

placement requires two motions:

a. Inward towards the workpiece as the rod is consumed

b. In the direction of cut

Use a protective lens shade #10 or higher to protect from arc ﬂash.

6.03 Hole Piercing

Perform most piercing operations without power.

1. Remove the Collet Nut Assembly from the front of the torch and remove the brass collet,

washer and spark arrestor from the torch.

2. Attach the Collet Extension Assembly to the front end of the torch and once tightened re-

install the spark arrestor, washer and brass collet into the assembly.

3. Slide the Extension Shield over the Collet Extension Assembly until it bottoms out against

the metal ring on the assembly.

4. Reinstall the Collet Nut Assembly onto the Collet Extension Assembly.

5. Insert the SLICE cutting rod into the torch and tighten the Collet Nut Assembly. Tap the SLICE

rod against the work surface and tighten the Collet Nut again, this ensures the cutting rod

is seated against the rubber washer.

6. Ignite the cutting rod as explained in the "Cutting without Power" section.

7. Move the burning rod to the pierce point and, with the rod angled away from the operator,

begin piercing the hole.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

8. Once the hole is under way, bring the cutting rod perpendicular to the surface of the workpiece.

Keep the cutting rod deep enough in the hole to feel slight resistance from the non-molten

material at the base of the hole. Use a slight circular motion while piercing the hole to keep

the rod free of molten material coming out of the hole.

9. Move the rod in and out of the hole occasionally to maintain an open path for the molten

material.

CAUTION

The molten material travels back up the rod while piercing. Wear proper

clothing for protection from the molten spray. Hold the torch at arm’s length

to keep the operator as far away from the molten material as possible. An

optional 6" (152.4 mm) collet extension and extension shield are available

for the SLICE cutting torch to protect the operator and torch.

NOTE!

Piercing in the at position is more difcult than piercing horizontally. Pierc-

ing at progresses more slowly. For example, piercing a hole in a oor is

more difcult and slower than piercing a hole in a wall.

6.04 Copper and Copper Alloys

CUTTING Because of the very rapid heat absorption of copper and its alloys, cut with power on these

materials. Use a maximum of 300 amps since copper quickly absorbs the heat created from the

exothermic reaction, reducing the effectiveness of the cutting process. Cutting with power releases

more heat so it is possible to cut some copper pieces. The larger the size of the part the more

difﬁcult it is to cut. A sawing motion into the cut kerf speeds cutting. Brass, bronze and other alloys

are slightly easier to cut, but these alloys should be cut using power, if possible.

PIERCING Use power when piercing copper and its alloys. This results in extremely fast rod

consumption. The higher the copper content of the part, the harder the material is to cut.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 7: IMPORTANT PROCESS VARIABLES

Exothermic cutting is easier than most cutting processes. Certain variables reduce the efﬁciency of

this process, resulting in poor cutting. The most important variables are listed and discussed below.

7.01 Oxygen Pressure

Oxygen maintains the exothermic burn and removes the molten material from the cut. Eighty psi

(551.6 kPa) yields the most efﬁcient cutting rates (amount of cut per inch of rod burned) on materials

up to 3" (76.2 mm) thick. Using pressures less than 80 psi (551.6 kPa) on such materials reduces

cutting rates due to inadequate pressure to remove the molten material.

However, scarﬁng is most efﬁcient using pressures under 80 psi (551.6 kPa). Lower pressures offer

a more controllable scarﬁng action. With material thicker than 3" (76.2 mm), pressures over 80 psi

(551.6 kPa) can be used to give the oxygen enough velocity to blow away molten material at the

bottom of the cut. Using higher pressures on thicker materials causes a more forceful oxygen jet

and faster rod consumption. A sawing motion at 80 psi (551.6 kPa) or a larger diameter rod may help

cut these materials more efﬁciently.

When piercing, 80 psi (551.6 kPa) is the best pressure to use. To pierce, an operator should reduce

the pressure slightly to control the distance the molten material travels. Once there is a hole, full

pressure should be used.

The operator can vary pressure by using the torch’s oxygen lever. When the thickness of the material

- usually more than 12" (304.8 mm) - needs added pressure to blow the molten material out of a

pierced hole, pressures above 80 psi (551.6 kPa) are used. This is the only exception.

The SLICE cutting process uses standard industrial-grade oxygen to support the exothermic reaction

and to remove molten metal. All SLICE equipment uses standard oxygen ﬁttings. SLICE torches are

equipped with 10 ft. (3.05 m) of 1/4" (6.4 mm) I.D. oxygen hose. The usual operating pressure is

80 psi (551.6 kPa). Applications such as cutting material sections 3" (76.2 mm) and thicker might

require higher operating pressures. Pressures as low as 40 psi (275.8 kPa) have been used to do

jobs such as washing off rivet heads and scarﬁng out small cracks for repair.

The oxygen consumption rate for SLICE cutting rods at 80 psi (551.6 kPa) is 7 to 7.5 cfm (0.21 cmm)

for the 1/4" (6.4 mm) diameter cutting rods and 12 to 13 cfm (0.34 to 0.37 cmm) for the 3/8" (95 mm)

diameter cutting rods. This rate varies if a different operating pressure is used.

WARNING

DO NOT use compressed air for exothermic cutting. Compressed air does

not contain enough oxygen to support the burn; therefore, impurities can

damage or destroy the torch and components. The torch could burn from

the inside or even explode from the buildup of dirt from the compressed air

in the oxygen-supply tube and cause serious injury to the operator.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

7.02 Amperage

Electrical current increases the heat from the reaction in exothermic cutting, allowing faster cutting.

200 amps yields the most efﬁcient cutting rates with power. When cutting with power and using less

than 200 amps, the amount of cut per minute will be lower. Amperage above 200 amps consumes

the rod faster, reducing the cut per inch of rod burned. Exothermic cutting equipment uses around

200 amps. Exceeding this amperage could cause equipment damage.

When cutting without power, current from the battery ignites the rod. To ignite the rod a surge of

at least 100 amps is needed. If the battery has not been properly charged it will not have enough

amperage to ignite the cutting rod.

7.03 Travel Speed

The cutting rod burns constantly without an electrical arc. Therefore, cut as fast as possible without

losing the cut kerf. If the travel speed is too fast, the material will not cut completely through and

molten slag will be blown back from the workpiece.

7.04 Electrode-To-Work Angle

The electrode-to-work angle is the most ﬂexible process variable. However, use of an improper angle

can cause reduced cutting efﬁciency. For most cutting jobs the ideal angle is between 45° and 80°.

For thicker material, hold the rod closer to an 80° angle. The electrode-to-work angle is typically a

drag angle - the rod is held so the tip of the burning rod is away from the direction of travel. Cutting

sheet metal is one exception since it is usually faster and better controlled when the user keeps a

45° angle or slightly less, and pushes the rod in the direction of cut. Aluminum, regardless of its

thickness, requires a 70° to 80° drag angle.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 8: APPLICATIONS

Industry Applications

Construction

Bridge repair. Cutting structural steel. Pierce and remove rivets and bolts without

damaging surrounding material. Punch holes in concrete, crack rocks. Highway

maintenance. Repair of highway guardrails. Cut reinforcing rods. Cut plaster or

concrete insulated pipes. Repairs on heavy equipment. Removing old structural

steel. Scrap clean up. Salvage work.

Plant Maintenance

Equipment/machinery repair. Remove headless bolts or frozen pins. Remove

seized bearings. Plant renovation. Removing old piping systems. Punch lag holes

to secure machinery. Repair machine bases. Remove old machinery. Cut up or

repair storage tanks.

Heavy Equipment

Maintenance

General maintenance (ﬁeld or shop repairs). Repair buckets. Remove seized or

worn pins. Cut worn or frayed control cables. Cut badly corroded material.

Foundry

Remove core sand trapped in holes of castings. Remove areas of imbedded sand.

Cut gates, risers, ﬁns from castings. Cut small multiple castings from runners.

Cut through slag in furnace cleanup. Punch relief holes in molds. Cut up spilled

materials for remelting. Cut up scrap castings. General plant maintenance.

Fire Service Rescue

Departments

Rapid entry into buildings. Cut through steel doors, dead bolts, barred windows,

overhead doors. Cut through debris (metal, concrete, plaster, rock) from building

collapse. Rescue operations.

Police/Swat

Rapid entry into buildings. Cut through steel doors, dead bolts, barred windows,

overhead doors. Rescue operations.

Railroad

Rail car repair and maintenance. Track maintenance/cut damaged sections of

track. Repairs in remote yard locations. Remove old rail loading docks.

Mining

Equipment maintenance (ﬁeld and shop repairs). Cut steel cables. Repair coal

tipples. Belt repairs. Remove abandoned piping and railways. Piercing holes in

rock to set blasting charges.

Metal Fabrication

Pierce starter holes in thick plates. Rough-cut pieces of material from large plates.

Field construction.

Demolition

Cut through rebar. Pierce concrete. Remove rivets and frozen bolts. Cut steel

imbedded in concrete. Equipment maintenance/repair. Cut corroded material.

Power Plants

General maintenance. Removal of piping. Cut out scrap feeder pans. Remove old

grating covered with refractory. Remove old boilers. Remove or repair storage

tanks.

Farming

General maintenance. Equipment/machinery repair. Repair stainless steel fertilizer

tanks. Cut metal encrusted with rust and/or mud.

Scrap/Salvage Yards

Cut all types of scrap metal, including cast iron, stainless steel, and aluminum.

Cut up scrap cars in remote areas of yard. Equipment maintenance. Cut badly

corroded or crusted material.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 9: TROUBLESHOOTING

9.01 General troubleshooting

Problem Solution

Rod burns but with no cut

progression.

1. Too much gap between the burning rod tip and the workpiece.

Must maintain slight pressure against workpiece.

2. Travel speed too slow.

3. Oxygen pressure too low.

Molten material not being

blown out of cut area.

1. Insufﬁcient oxygen pressure being used.

2. Rubber washer behind collet chuck worn and needs to be

replaced.

3. Travel speed too fast.

Battery will only start a few

rods before charge is depleted.

1. Battery was not given sufﬁcient time to recharge.

2. Battery needs to be replaced.

3. Battery left exposed to subfreezing temperatures.

Torch shield is being burnt off

around Collet Nut.

1. Rod is not properly seated in torch. Refer to Section 6 on

operating techniques to properly seat rod.

2. Collet extension not used when piercing holes.

When piercing anything but

copper and its alloys, the rod

consumes extremely fast.

1. Operator is piercing with power. All piercing operations

except ones on copper and its alloys should be done without

power.

Arced collet chuck and/or rod

is burned off just outside of

collet chuck.

1. Using a CC type welding power source.

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

9.02 IGNITION SOURCE LED DISPLAY GUIDE

Condition #

Charger

Connected

Test

Button

Left

LED

Center

LED

Right

LED

Condition Action

1 No Un-pressed Off Off Off Standby None

2 Yes Un-pressed Off Off Off

Wall power disconnected /

Internal electronics fault

Verify electrical outlet is energized.

Verify AC/DC Power Adapter Output connector is

fully inserted into DC Input socket.

Return unit for repair.

3 Yes Un-pressed Off Amber Amber Analyzing battery (30 seconds)

Wait 30 seconds for charge status. New LED

conﬁguration will appear.

4 Yes Un-pressed Off Amber Off Charging battery

Wait up to 2-5 hours for a fully discharged

battery.

5 Yes Un-pressed Off Off Amber

Battery fully charged /

Trickle mode

Disconnect charger and store or keep charger

connected or use unit.

6 Yes Un-pressed Red Off Off

Thermal fuse tripped /

Battery fault /

Battery missing

Disconnect charger and wait 10 minutes for fuse

to reset / Replace battery /

Return unit for repair

7 Yes Un-pressed

Red

(Flash)

Off Off Battery temperature high

Wait for unit to cool down /

Move to cooler location

8 No Pressed Off Off Off Battery <20% capacity Unit not recommended for use / Connect charger

9 No Pressed Off Green Off Battery 20% to 60% capacity

Unit needs charging / Can be operated / Connect

charger

10 No Pressed Green Off Off Battery 60% to 80% capacity Connect charger / Unit ready for use

11 No Pressed Green Green Green Battery >80% capacity Unit ready for use

12 Yes Pressed Off Off Off Battery <20% capacity None

13 Yes Pressed Green Off Off Battery 20% to 60% capacity None

14 Yes Pressed Off Green Off Battery 60% to 80% capacity None

9 Yes Pressed Green Green Green Battery >80% capacity Disconnect Charger / Unit ready for use

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

9.02 IGNITION SOURCE LED DISPLAY GUIDE

Condition #

Charger

Connected

Test

Button

Left

LED

Center

LED

Right

LED

Condition Action

1 No Un-pressed Off Off Off Standby None

2 Yes Un-pressed Off Off Off

Wall power disconnected /

Internal electronics fault

Verify electrical outlet is energized.

Verify AC/DC Power Adapter Output connector is

fully inserted into DC Input socket.

Return unit for repair.

3 Yes Un-pressed Off Amber Amber Analyzing battery (30 seconds)

Wait 30 seconds for charge status. New LED

conﬁguration will appear.

4 Yes Un-pressed Off Amber Off Charging battery

Wait up to 2-5 hours for a fully discharged

battery.

5 Yes Un-pressed Off Off Amber

Battery fully charged /

Trickle mode

Disconnect charger and store or keep charger

connected or use unit.

6 Yes Un-pressed Red Off Off

Thermal fuse tripped /

Battery fault /

Battery missing

Disconnect charger and wait 10 minutes for fuse

to reset / Replace battery /

Return unit for repair

7 Yes Un-pressed

Red

(Flash)

Off Off Battery temperature high

Wait for unit to cool down /

Move to cooler location

8 No Pressed Off Off Off Battery <20% capacity Unit not recommended for use / Connect charger

9 No Pressed Off Green Off Battery 20% to 60% capacity

Unit needs charging / Can be operated / Connect

charger

10 No Pressed Green Off Off Battery 60% to 80% capacity Connect charger / Unit ready for use

11 No Pressed Green Green Green Battery >80% capacity Unit ready for use

12 Yes Pressed Off Off Off Battery <20% capacity None

13 Yes Pressed Green Off Off Battery 20% to 60% capacity None

14 Yes Pressed Off Green Off Battery 60% to 80% capacity None

9 Yes Pressed Green Green Green Battery >80% capacity Disconnect Charger / Unit ready for use

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 10: PARTS LISTING

SLICE STRIKER REPLACEMENT PARTS

Art# A-13642

Item No. Part No. Description

1 94-370-198 Handle Halves - LH / RH

2 94-370-202 SLICE Striker Slider Knob

3 96-070-033 Striker Bar

4 96-130-320 Cable Assembly

5 96-070-034 Striker Shield

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

BATTERY IGNITION SOURCE

Art# A-13640

CAUTION

THIS UNIT CONTAINS A LEAD ACID BATTERY WHICH RELEASES EXPLOSIVE

HYDROGEN GAS WHEN BEING CHARGED. CHARGE THIS BATTERY ONLY IN A

VENTILATED LOCATION DESIGNATED AS A LEAD-ACID BATTERY CHARGING

AREA. DO NOT CHARGE THIS BATTERY WHILE OPERATING THIS TORCH.

CAUTION

THIS UNIT CONTAINS A LEAD ACID BATTERY WHICH RELEASES EXPLOSIVE

HYDROGEN GAS WHEN BEING CHARGED. CHARGE THIS BATTERY ONLY IN A

VENTILATED LOCATION DESIGNATED AS A LEAD-ACID BATTERY CHARGING

AREA. DO NOT CHARGE THIS BATTERY WHILE OPERATING THIS TORCH.

Item No. Part No. Description

1 94-134-038 Battery Pack Case Back Half

2 94-134-039 Battery Pack Case Front Half

3 96-162-758 Circuit Board Assembly

4 96-076-018 Battery Assembly

5 96-169-374 Red Female Panel Receptacle

6 96-169-375 Black Female Panel Receptacle

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SLICE TORCH REPLACEMENT PARTS

7 6 5 4

Art# A-13641_AB

Item No. Part No. Description

1 94-370-197 SLICE Handle - RH & LH (w/screws)

3 94-777-112 Shield

94-168-022 1/4" Collet Nut Assembly

95-168-024 3/8" Collet Nut Assembly

94-158-048 1/4" Collet Chuck

94-158-045 3/8" Collet Chuck

6 94-940-109 Washer

7 94-305-009 Flashback Arrestor

8 94-378-338 Head/Body Assembly

9 94-476-086 Lever Assembly

10 94-396-193 Oxygen Hose - 10 ft. (3m)

96-130-279 Cable Assembly for SLICE Torch Part No. 03-003-010

96-130-276 Cable Assembly (Utility & Industrial Pack)

96-130-319 Cable Assembly (Battery & Complete Pack)

12 94-463-032 3/8" Collet Conversion Kit

SLICE EXOTHERMIC CUTTING EQUIPMENT

89250840

SECTION 11: STATEMENT OF WARRANTY

LIMITED WARRANTY: Arcair, an ESAB brand, warrants that its products will be free of defects in

workmanship or material. Should any failure to conform to this warranty appear within the time

period applicable to the Arcair products as stated below, Arcair shall, upon notiﬁcation thereof and

substantiation that the product has been stored, installed, operated, and maintained in accordance

with Arcair’s speciﬁcations, instructions, recommendations and recognized standard industry practice,

and not subject to misuse, repair, neglect, alteration, or accident, correct such defects by suitable

repair or replacement, at Arcair’s sole option, of any components or parts of the product determined

by Arcair to be defective.

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE.

LIMITATION OF LIABILITY: Arcair, an ESAB brand, shall not under any circumstances be liable

for special or consequential damages, such as, but not limited to, damage or loss of purchased or

replacement goods, or claims of customers of distributor (hereinafter the "Purchaser") for service

interruption. The remedies of the Purchaser set forth herein are exclusive and the liability of Arcair

with respect to any contract, or anything done in connection therewith such as the performance or

breach thereof, or from the manufacture, sale, delivery, resale, or use of any goods covered by or

furnished by Arcair whether arising out of contract, negligence, strict tort, or under any warranty, or

otherwise, shall not, except as expressly provided herein, exceed the price of the goods upon which

such liability is based.

THIS WARRANTY BECOMES INVALID IF REPLACEMENT PARTS OR ACCESSORIES ARE USED

WHICH MAY IMPAIR THE SAFETY OR PERFORMANCE OF ANY ARCAIR PRODUCT.

THIS WARRANTY IS INVALID IF THE PRODUCT IS SOLD BY NON-AUTHORIZED PERSONS.

This warranty is effective for the time stated in the Warranty Schedule beginning on the date that the

authorized distributor delivers the products to the Purchaser.

Warranty repairs or replacement claims under this limited warranty must be submitted by an authorized

Arcair repair facility within thirty (30) days of the repair. No transportation costs of any kind will be

paid under this warranty. Transportation charges to send products to an authorized warranty repair

facility shall be the responsibility of the Purchaser. All returned goods shall be at the Purchaser’s risk

and expense. This warranty supersedes all previous Arcair warranties.

www.esab.com

Europe

AUSTRIA

ESAB Ges.m.b.H

Vienna-Liesing

Tel: +43 1 888 25 11

Fax: +43 1 888 25 11 85

BELGIUM

S.A. ESAB N.V.

Heist-op-den-Berg

Tel: +32 70 233 075

Fax: +32 15 257 944

BULGARIA

ESAB Kft Representative Ofﬁce

Soﬁa

Tel/Fax: +359 2 974 42 88

THE CZECH REPUBLIC

ESAB VAMBERK s.r.o.

Vamberk

Tel: +420 2 819 40 885

Fax: +420 2 819 40 120

DENMARK

Aktieselskabet ESAB

Herlev

Tel: +45 36 30 01 11

Fax: +45 36 30 40 03

FINLAND

ESAB Oy

Helsinki

Tel: +358 9 547 761

Fax: +358 9 547 77 71

FRANCE

ESAB France S.A.

Cergy Pontoise

Tel: +33 1 30 75 55 00

Fax: +33 1 30 75 55 24

GERMANY

ESAB Welding & Cutting

GmbHZweigstelle

Langenfeld

Tel.: +49 2173 3945 0

Fax.: +49 2173 3945 218

GREAT BRITAIN

ESAB Group (UK) Ltd

Waltham Cross

Tel: +44 1992 76 85 15

Fax: +44 1992 71 58 03

ESAB Automation Ltd

Andover

Tel: +44 1264 33 22 33

Fax: +44 1264 33 20 74

HUNGARY

ESAB Kft

Budapest

Tel: +36 1 20 44 182

Fax: +36 1 20 44 186

ITALY

ESAB Saldatura S.p.A.

Bareggio (Mi)

Tel: +39 02 97 96 8.1

Fax: +39 02 97 96 87 01

THE NETHERLANDS

ESAB Nederland B.V.

Amersfoort

Tel: +31 33 422 35 55

Fax: +31 33 422 35 44

NORWAY

AS ESAB

Larvik

Tel: +47 33 12 10 00

Fax: +47 33 11 52 03

POLAND

ESAB Sp.zo.o.

Katowice

Tel: +48 32 351 11 00

Fax: +48 32 351 11 20

PORTUGAL

ESAB Lda

Lisbon

Tel: +351 8 310 960

Fax: +351 1 859 1277

ROMANIA

ESAB Romania Trading SRL

Bucharest

Tel: +40 316 900 600

Fax: +40 316 900 601

RUSSIA

LLC ESAB

Moscow

Tel: +7 (495) 663 20 08

Fax: +7 (495) 663 20 09

SLOVAKIA

ESAB Slovakia s.r.o.

Bratislava

Tel: +421 7 44 88 24 26

Fax: +421 7 44 88 87 41

SPAIN

ESAB Ibérica S.A.

San Fernando de Henares

Tel: +34 91 878 3600

Fax: +34 91 802 3461

SWEDEN

ESAB Sverige AB

Gothenburg

Tel: +46 31 50 95 00

Fax: +46 31 50 92 22

ESAB international AB

Gothenburg

Tel: +46 31 50 90 00

Fax: +46 31 50 93 60

SWITZERLAND

ESAB AG

Baar

Tel.: +41 44 741 25 25

Fax.: +41 44 740 30 55

UKRAINE

ESAB Ukraine LLC

Kiev

Tel: +38 (044) 501 23 24

Fax: +38 (044) 575 21 88

North and South America

ARGENTINA

CONARCO

Buenos Aires

Tel: +54 11 4 753 4039

Fax: +54 11 4 753 6313

BRAZIL

ESAB S.A.

Contagem-MG

Tel: +55 31 2191 4333

Fax: +55 31 2191 4440

CANADA

ESAB Group Canada Inc.

Missisauga, Ontario

Tel: +1 905 670 02 20

Fax: +1 905 670 48 79

MEXICO

ESAB Mexico S.A.

Monterrey

Tel: +52 8 350 5959

Fax: +52 8 350 7554

USA

ESAB Welding & Cutting

Products

Florence, SC

Tel: +1 843 669 44 11

Fax: +1 843 664 57 48

Asia/Pacific

AUSTRALIA

ESAB South Paciﬁc

Archerﬁeld BC QLD 4108

Tel: +61 1300 372 228

Fax: +61 7 3711 2328

CHINA

Shanghai ESAB A/P

Shanghai

Tel: +86 21 2326 3000

Fax: +86 21 6566 6622

INDIA

ESAB India Ltd

Calcutta

Tel: +91 33 478 45 17

Fax: +91 33 468 18 80

INDONESIA

P.T. ESABindo Pratama

Jakarta

Tel: +62 21 460 0188

Fax: +62 21 461 2929

JAPAN

ESAB Japan

Tokyo

Tel: +81 45 670 7073

Fax: +81 45 670 7001

MALAYSIA

ESAB (Malaysia) Snd Bhd

USJ

Tel: +603 8023 7835

Fax: +603 8023 0225

SINGAPORE

ESAB Asia/Paciﬁc Pte Ltd

Singapore

Tel: +65 6861 43 22

Fax: +65 6861 31 95

SOUTH KOREA

ESAB SeAH Corporation

Kyungnam

Tel: +82 55 269 8170

Fax: +82 55 289 8864

UNITED ARAB EMIRATES

ESAB Middle East FZE

Dubai

Tel: +971 4 887 21 11

Fax: +971 4 887 22 63

Africa

EGYPT

ESAB Egypt

Dokki-Cairo

Tel: +20 2 390 96 69

Fax: +20 2 393 32 13

SOUTH AFRICA

ESAB Africa Welding & Cutting

Ltd

Durbanvill 7570 - Cape Town

Tel: +27 (0)21 975 8924

Distributors

For addresses and phone

numbers to our distributors in

other countries, please visit our

home page

www.esab.eu

ESAB subsidiaries and representative ofﬁces

GUIDE

D'INSTALLATION

D'UTILISATION

ÉQUIPEMENT

DE DÉCOUPAGE

EXOTHERMIQUE SLICE®

Français

(French)

Torche SLICE®

Ensemble SLICE®

Percuteur SLICE®

Art# A-13635

Révision : AC Date d'émission : 24-01-2019 Manuel nº : 89250840FR

NOUS APPRÉCIONS VOTRE FIDÉLITÉ !

Félicitations pour l'achat de votr

produit Arcair®. Nous sommes ﬁers de vous avoir comme

client et nous nous efforcerons de vous fournir le meilleur service possible et d'apporter notre

soutien à l'industrie. Ce produit est protégé par notre large garantie et notre réseau mondial

de service. Pour localiser votre distributeur ou agence de service le plus proche, rendez-vous

sur le site www.esab.com/arcair.

Les instructions du présent manuel donnent des informations sur la façon d'installer et d'utiliser

votre produit Arcair. Notre préoccupation principale est votre satisfaction et l'utilisation appropriée

du produit. Il est donc important de prendre le temps de lire ce guide en entier, en particulier les

Consignes de sécurité. Ceci permet d'éviter les risques possibles liés à l'utilisation du produit.

VOUS ÊTES EN BONNE COMPAGNIE !

La marque de choix des entrepreneurs et des fabricants dans le monde entier.

Arcair® est une marque Internationale de systèmes de coupage d'ESAB. Nos produits sont

destinés aux principaux secteurs industriels spécialisés en soudure notamment les secteurs

de la fabrication, de la Construction, automobile, de l'aérospatiale, de l'ingénierie, de l'industrie

rurale et du bricolage, ainsi qu'aux amateurs.

Nous nous démarquons de nos concurrents grâce à nos produits ﬁables et d'avant-garde qui

ont fait leurs preuves au ﬁl des ans. Nous sommes ﬁers de nos innovations techniques, nos prix

compétitifs, nos délais de livraison hors pair, notre service à la clientèle et notre soutien technique

de qualité supérieure, en plus de l'excellence de notre savoir dans le domaine de la vente.

Avant tout, nous sommes engagés dans la conception de produits aux technologies innovatrices

pour obtenir un environnement de travail plus sûr dans le domaine de la soudure.

AVERTISSEMENT

Lire et assimiler l'intégralité du présent manuel et les consignes

de sécurité de votre employeur avant l'installation, l'exploitation ou

l'entretien de l'équipement. L'information contenue dans ce Guide re-

présente le bon jugement du fabricant, mais celui-ci n'assume aucune

responsabilité lors de l'utilisation.

ÉQUIPEMENT DE DÉCOUPAGE EXOTHERMIQUE SLICE®

GUIDE D'INSTALLATION ET D'UTILISATION

Numéro du manuel 89250840FR

Publié par :

ESAB Group Inc.

2800 Airport Rd.

Denton, TX. 76208

(940) 566-2000

www.esab.com/arcair

ENTRETIEN à la clientèle aux États-Unis : (800) 426-1888

ENTRETIEN à la clientèle Internationale : (940) 381-1212

Il est interdit de reproduire tout ou partie de ce document sans la permission de l'éditeur.

L'éditeur décline toute responsabilité envers les parties en cas de pertes ou de dommages provoqués

par une erreur ou une omission ﬁgurant dans ce Guide, qu'elle soit le résultat d'une négligence, d'un

accident ou d'une autre Cause.

Pour la spéciﬁcation des matériaux d'impression dans les Amériques, voir le document 47X1920

Pour la spéciﬁcation des matériaux d'impression dans les Europe, voir le document 47X1953

Publié le : 08-03-2018

Date de révision: 24-01-2019

Conserver les renseignements suivant pour la garantie :

Endroit de l'achat : _______________________________________

Date de l'achat : _________________________________________

No de série de l'appareil : _________________________________________

ASSUREZ-VOUS QUE CE DOCUMENT D’INFORMATION EST DISTRIBUÉ À L’OPÉRATEUR.

DES COPIES SUPPLÉMENTAIRES SONT DISPONIBLES CHEZ VOTRE FOURNISSEUR.

MISE EN GARDE

Les INSTRUCTIONS suivantes sont destinées aux opérateurs qualiés seulement.

Si vous n’avez pas une connaissance approfondie des principes de fonctionnement

et des règles de sécurité applicables au soudage à l’arc et à l’équipement de

coupage, nous vous suggérons de lire notre brochure " Précautions et pratiques

de sécurité pour le soudage à l’arc, le coupage et le gougeage ", Formulaire 52-