Capkold DHINA2 El manual del propietario

Capkold
Marca
Capkold
Modelo
DHINA2
Tipo
El manual del propietario
NOMBRE DEL PROYECTO:
EMPLAZAMIENTO:
ELEMENTO Nº:
CANT:
MODELO Nº:
AIA Nº:
SIS Nº:
CAPKOLD
®
SISTEMAS COOK-CHILL
Marmita inclinable, a gas, autónoma
con agitador no inclinable
Marmitas CapKold
CKDH/1NA/2-100 160590 RevA
Revisión 10/13
MODELOS DISPONIBLES:
DH/INA/2-100 (100 GALONES (378,5 LITROS))
CONSTRUCCIÓN
• Camisa de fondo hemisférico de marmita a 50 PSI
(3,45 bares), según código ASME, e inscrita en la
National Board.
• C.S.A. Diseño certificado e inscrito en NSF
• Intercambiador de calor a gas con aletas de alta
eficiencia, con potencia de entrada máxima de
360.000 BTU/h
• Reborde reforzado y labio de control de caudal
de vertido
• Inclinación del cuerpo de la marmita y del conjunto
del agitador mediante husillo de tornillo accionado
eléctricamente para el vertido y limpieza
• Ignición electrónica
• Válvula neumática de descarga de producto de
acero inoxidable de 3" (7,62 cm) al ras con el
fondo de la marmita.
• Interior de la marmita y todas las piezas que se
mojan de acero inoxidable tipo 316. Tipo 304
todas las demás.
• Grifo de llenado de agua de chorro giratorio
de 3/4" (1,9 cm) montado en el borde
• Conexión de aire comprimido de la bomba/estación
de llenado CapKold® (ver CKPF/3)
• Capacidad de trabajo 100 galones (378,5 litros)
• Listado NSF
DISEñO DEL AgITADOR:
• Agitador fijo, con entrada inclinada a 45º respecto
a la línea de centros
• Agitador de velocidad variable, con transmisión
de 2 CV, con control de precisión entre 4-36 RPM
• El conjunto del agitador se inclina junto con el
cuerpo de la marmita
Marmita CapKold® modelo DH/INA/2-100, con capacidad de trabajo 100 galones (378,5 litros), autónoma,
con alta eciencia, 360.000 BTU/h de gas, fondo hemisférico con camisa de vapor, con agitador inclinable.
Inclinación del cuerpo de la marmita mediante husillo de tornillo accionado eléctricamente para simplicar
la carga de producto, la limpieza de la marmita y la transferencia de productos no bombeables. El conjunto
del agitador se inclina junto con el cuerpo de la marmita. Presión máxima en la camisa 50 PSI (3,45 bares),
válvula neumática de descarga de producto de 3" (7,62 cm) y transmisión de agitador de velocidad variable.
MARMITA A GAS CON AGITADOR NO INCLINABLE MODELO DH/INA/2
PAqUETE DE CONTROL INTEgRAL:
• Indicador/control digital de la temperatura
del producto
• Indicador luminoso
• Conmutador doble de seguridad de inicio
del agitador
• Control del agitador de velocidad variable
• Botón de paro de emergencia del agitador
• Piloto indicador de corriente
• Interruptor e indicador de la inclinación del
cuerpo de la marmita
• Luz indicadora de nivel bajo de agua
(camisa de la marmita)
• Medidor automático de agua preconfigurado
• Botón de desplazamiento del agitador (rotación
parcial a 4 RPM)
ORIgEN DE FABRICACIÓN: Diseño
y fabricación en Estados Unidos.
OPCIONALES/
ACCESORIOS:
Gráfico de registro de la
temperatura del producto
Tapa de 2 piezas con bisagra
Filtro desmontable del producto
en el labio vertedor
Paquete cerrado
Labio de vertido
888-994-7636, unifiedbrands.net
© 2016 Unified Brands. Todos los derechos reservados. Unified Brands es una empresa filial propiedad de Dover Corporation.
DH/INA/2
* ALLOW SAFETY VALVE LEVER TO SNAP DOWN.
STOP
AGITATOR SPEED
FORWARD
JOGRUN
START
BACK
HIGH
TILT
E-STOP
START/JOG
HEAT
SIMMER
OFF
* LIFT SAFETY VALVE LEVER TO VENT KETTLE
* HEAT KETTLE UNTIL PRESSURE GAUGE READS 5 PSI.
BETWEEN 20-30 in. Hg BELOW ZERO (WHEN KETTLE IS COLD)
* CHECK FOR VACUUM IN KETTLE. PRESSURE GAUGE SHOULD READ
** WARNING STEAM WILL ESCAPE **
ESTABLISH VACUUM
BEFORE OPERATION
SPEED CONTROL
LOW WATER CUTOFF
POWER
4. 1" NPT GAS SUPPLY
11.
24" SERVICE CLEARANCE REQUIRED
9. APPROX. SHIPPING WEIGHT: 1750 LBS
8. ELECTRIC MOTOR DRIVEN POWER TILT FEATURE
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
10. COLD WATER SUPPLY - 3/4" HOSE CONNECTION
6. 3" AIR ACTUATED BOTTOM DROP DOWN VALVE
7. 2 H.P. VARIABLE SPEED AGITATOR MOTOR
5. 50 PSI ASME APPROVED
KETTLE
2. ELECTRICAL CONNECTION 1/2" CONDUIT
ELECTRICAL SUPPLY VOLTAGE: 208/240/480 VAC
3 PHASE 60 Hz
3.
PRODUCT SPECIFICATIONS:
P/N 115211 REV. E
3/8" NPT AIR SUPPLY: 100 PSI MAX.
C
L
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW REAR VIEW
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
INCOMING GAS SUPPLY
PRESSURES
GAS TYPE
NATURAL
PROPANE
MINIMUM
7" W.C.
11" W.C.
MAXIMUM
14" W.C.
14" W.C.
POWER SUPPLY
VOLTAGE 3 PHASE
208 11 AMPS
240 10 AMPS
--
5 AMPS480
1. INPUT RATE: 360,000 BTU/HR
12.
UNIT MUST BE MOUNTED ON NON-COMBUSTIBLE
FLOORING.
MOUNTING HOLE
FLOOR PATTERN
C
L
KETTLE
13.
PRODUCT OVERFLOW WHEN KETTLE IS STOPPED
DURING TILT CYCLE
14.
42" DRAIN RECOMMENDED
0.34 GPM @ 30 PSI
(SUPPLY 30 PSI MIN. & 60 PSI MAX.)
FULL TILT POSITION
15. RECOMMENDED LOCATION FOR ACCESS TO
4-20 MA FOOD PROBE OUTPUT ON CONTROLLER.
KETTLE
L
C
KETTLE
L
C
64 1/4"
53-3/8"
34"DIA
54 1/4"
31"
3/4" NPT WATER SPOUT
12"
38"
33-3/4"
35-3/4"
12-1/2"
4 10
5"3
2
3-1/2"
2
8
47 13/32
5 1/2
16"
7
6
SEE NOTE 14
71"
6-1/2"
22" MIN. COMBUSTIBLE
MATERIAL CLEARANCE
1-1/2"
2-1/2"
10-1/4"
7/8"
16"
4-5/32"
4"
6-5/8"
11
11
BOTTOM OF BOTH SERVICE ACCESS PANELS
30"
POUR PATH
SEE NOTE 14
4"
SEE NOTE 13
15
15
SELF-CONTAINED, GAS HEATED, TILTING KETTLE
WITH NON-TILT OUT INCLINED AGITATOR
3"
32-1/8"
* ALLOW SAFETY VALVE LEVER TO SNAP DOWN.
STOP
AGITATOR SPEED
FORWARD
JOGRUN
START
BACK
HIGH
TILT
E-STOP
START/JOG
HEAT
SIMMER
OFF
* LIFT SAFETY VALVE LEVER TO VENT KETTLE
* HEAT KETTLE UNTIL PRESSURE GAUGE READS 5 PSI.
BETWEEN 20-30 in. Hg BELOW ZERO (WHEN KETTLE IS COLD)
* CHECK FOR VACUUM IN KETTLE. PRESSURE GAUGE SHOULD READ
** WARNING STEAM WILL ESCAPE **
ESTABLISH VACUUM
BEFORE OPERATION
SPEED CONTROL
LOW WATER CUTOFF
POWER
4. 1" NPT GAS SUPPLY
11.
24" SERVICE CLEARANCE REQUIRED
9. APPROX. SHIPPING WEIGHT: 1750 LBS
8. ELECTRIC MOTOR DRIVEN POWER TILT FEATURE
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
10. COLD WATER SUPPLY - 3/4" HOSE CONNECTION
6. 3" AIR ACTUATED BOTTOM DROP DOWN VALVE
7. 2 H.P. VARIABLE SPEED AGITATOR MOTOR
5. 50 PSI ASME APPROVED
KETTLE
2. ELECTRICAL CONNECTION 1/2" CONDUIT
ELECTRICAL SUPPLY VOLTAGE: 208/240/480 VAC
3 PHASE 60 Hz
3.
PRODUCT SPECIFICATIONS:
P/N 115211 REV. E
3/8" NPT AIR SUPPLY: 100 PSI MAX.
C
L
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW REAR VIEW
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
INCOMING GAS SUPPLY
PRESSURES
GAS TYPE
NATURAL
PROPANE
MINIMUM
7" W.C.
11" W.C.
MAXIMUM
14" W.C.
14" W.C.
POWER SUPPLY
VOLTAGE 3 PHASE
208 11 AMPS
240 10 AMPS
--
5 AMPS480
1. INPUT RATE: 360,000 BTU/HR
12.
UNIT MUST BE MOUNTED ON NON-COMBUSTIBLE
FLOORING.
MOUNTING HOLE
FLOOR PATTERN
C
L
KETTLE
13.
PRODUCT OVERFLOW WHEN KETTLE IS STOPPED
DURING TILT CYCLE
14.
42" DRAIN RECOMMENDED
0.34 GPM @ 30 PSI
(SUPPLY 30 PSI MIN. & 60 PSI MAX.)
FULL TILT POSITION
15. RECOMMENDED LOCATION FOR ACCESS TO
4-20 MA FOOD PROBE OUTPUT ON CONTROLLER.
KETTLE
L
C
KETTLE
L
C
64 1/4"
53-3/8"
34"DIA
54 1/4"
31"
3/4" NPT WATER SPOUT
12"
38"
33-3/4"
35-3/4"
12-1/2"
4 10
5"3
2
3-1/2"
2
8
47 13/32
5 1/2
16"
7
6
SEE NOTE 14
71"
6-1/2"
22" MIN. COMBUSTIBLE
MATERIAL CLEARANCE
1-1/2"
2-1/2"
10-1/4"
7/8"
16"
4-5/32"
4"
6-5/8"
11
11
BOTTOM OF BOTH SERVICE ACCESS PANELS
30"
POUR PATH
SEE NOTE 14
4"
SEE NOTE 13
15
15
SELF-CONTAINED, GAS HEATED, TILTING KETTLE
WITH NON-TILT OUT INCLINED AGITATOR
3"
32-1/8"
* ALLOW SAFETY VALVE LEVER TO SNAP DOWN.
STOP
AGITATOR SPEED
FORWARD
JOGRUN
START
BACK
HIGH
TILT
E-STOP
START/JOG
HEAT
SIMMER
OFF
* LIFT SAFETY VALVE LEVER TO VENT KETTLE
* HEAT KETTLE UNTIL PRESSURE GAUGE READS 5 PSI.
BETWEEN 20-30 in. Hg BELOW ZERO (WHEN KETTLE IS COLD)
* CHECK FOR VACUUM IN KETTLE. PRESSURE GAUGE SHOULD READ
** WARNING STEAM WILL ESCAPE **
ESTABLISH VACUUM
BEFORE OPERATION
SPEED CONTROL
LOW WATER CUTOFF
POWER
4. 1" NPT GAS SUPPLY
11.
24" SERVICE CLEARANCE REQUIRED
9. APPROX. SHIPPING WEIGHT: 1750 LBS
8. ELECTRIC MOTOR DRIVEN POWER TILT FEATURE
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
10. COLD WATER SUPPLY - 3/4" HOSE CONNECTION
6. 3" AIR ACTUATED BOTTOM DROP DOWN VALVE
7. 2 H.P. VARIABLE SPEED AGITATOR MOTOR
5. 50 PSI ASME APPROVED
KETTLE
2. ELECTRICAL CONNECTION 1/2" CONDUIT
ELECTRICAL SUPPLY VOLTAGE: 208/240/480 VAC
3 PHASE 60 Hz
3.
PRODUCT SPECIFICATIONS:
P/N 115211 REV. E
3/8" NPT AIR SUPPLY: 100 PSI MAX.
C
L
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW REAR VIEW
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
INCOMING GAS SUPPLY
PRESSURES
GAS TYPE
NATURAL
PROPANE
MINIMUM
7" W.C.
11" W.C.
MAXIMUM
14" W.C.
14" W.C.
POWER SUPPLY
VOLTAGE 3 PHASE
208 11 AMPS
240 10 AMPS
--
5 AMPS480
1. INPUT RATE: 360,000 BTU/HR
12.
UNIT MUST BE MOUNTED ON NON-COMBUSTIBLE
FLOORING.
MOUNTING HOLE
FLOOR PATTERN
C
L
KETTLE
13.
PRODUCT OVERFLOW WHEN KETTLE IS STOPPED
DURING TILT CYCLE
14.
42" DRAIN RECOMMENDED
0.34 GPM @ 30 PSI
(SUPPLY 30 PSI MIN. & 60 PSI MAX.)
FULL TILT POSITION
15. RECOMMENDED LOCATION FOR ACCESS TO
4-20 MA FOOD PROBE OUTPUT ON CONTROLLER.
KETTLE
L
C
KETTLE
L
C
64 1/4"
53-3/8"
34"DIA
54 1/4"
31"
3/4" NPT WATER SPOUT
12"
38"
33-3/4"
35-3/4"
12-1/2"
4 10
5"3
2
3-1/2"
2
8
47 13/32
5 1/2
16"
7
6
SEE NOTE 14
71"
6-1/2"
22" MIN. COMBUSTIBLE
MATERIAL CLEARANCE
1-1/2"
2-1/2"
10-1/4"
7/8"
16"
4-5/32"
4"
6-5/8"
11
11
BOTTOM OF BOTH SERVICE ACCESS PANELS
30"
POUR PATH
SEE NOTE 14
4"
SEE NOTE 13
15
15
SELF-CONTAINED, GAS HEATED, TILTING KETTLE
WITH NON-TILT OUT INCLINED AGITATOR
3"
32-1/8"
* ALLOW SAFETY VALVE LEVER TO SNAP DOWN.
STOP
AGITATOR SPEED
FORWARD
JOGRUN
START
BACK
HIGH
TILT
E-STOP
START/JOG
HEAT
SIMMER
OFF
* LIFT SAFETY VALVE LEVER TO VENT KETTLE
* HEAT KETTLE UNTIL PRESSURE GAUGE READS 5 PSI.
BETWEEN 20-30 in. Hg BELOW ZERO (WHEN KETTLE IS COLD)
* CHECK FOR VACUUM IN KETTLE. PRESSURE GAUGE SHOULD READ
** WARNING STEAM WILL ESCAPE **
ESTABLISH VACUUM
BEFORE OPERATION
SPEED CONTROL
LOW WATER CUTOFF
POWER
4. 1" NPT GAS SUPPLY
11.
24" SERVICE CLEARANCE REQUIRED
9. APPROX. SHIPPING WEIGHT: 1750 LBS
8. ELECTRIC MOTOR DRIVEN POWER TILT FEATURE
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
10. COLD WATER SUPPLY - 3/4" HOSE CONNECTION
6. 3" AIR ACTUATED BOTTOM DROP DOWN VALVE
7. 2 H.P. VARIABLE SPEED AGITATOR MOTOR
5. 50 PSI ASME APPROVED
KETTLE
2. ELECTRICAL CONNECTION 1/2" CONDUIT
ELECTRICAL SUPPLY VOLTAGE: 208/240/480 VAC
3 PHASE 60 Hz
3.
PRODUCT SPECIFICATIONS:
P/N 115211 REV. E
3/8" NPT AIR SUPPLY: 100 PSI MAX.
C
L
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW REAR VIEW
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
INCOMING GAS SUPPLY
PRESSURES
GAS TYPE
NATURAL
PROPANE
MINIMUM
7" W.C.
11" W.C.
MAXIMUM
14" W.C.
14" W.C.
POWER SUPPLY
VOLTAGE 3 PHASE
208 11 AMPS
240 10 AMPS
--
5 AMPS480
1. INPUT RATE: 360,000 BTU/HR
12.
UNIT MUST BE MOUNTED ON NON-COMBUSTIBLE
FLOORING.
MOUNTING HOLE
FLOOR PATTERN
C
L
KETTLE
13.
PRODUCT OVERFLOW WHEN KETTLE IS STOPPED
DURING TILT CYCLE
14.
42" DRAIN RECOMMENDED
0.34 GPM @ 30 PSI
(SUPPLY 30 PSI MIN. & 60 PSI MAX.)
FULL TILT POSITION
15. RECOMMENDED LOCATION FOR ACCESS TO
4-20 MA FOOD PROBE OUTPUT ON CONTROLLER.
KETTLE
L
C
KETTLE
L
C
64 1/4"
53-3/8"
34"DIA
54 1/4"
31"
3/4" NPT WATER SPOUT
12"
38"
33-3/4"
35-3/4"
12-1/2"
4 10
5"3
2
3-1/2"
2
8
47 13/32
5 1/2
16"
7
6
SEE NOTE 14
71"
6-1/2"
22" MIN. COMBUSTIBLE
MATERIAL CLEARANCE
1-1/2"
2-1/2"
10-1/4"
7/8"
16"
4-5/32"
4"
6-5/8"
11
11
BOTTOM OF BOTH SERVICE ACCESS PANELS
30"
POUR PATH
SEE NOTE 14
4"
SEE NOTE 13
15
15
SELF-CONTAINED, GAS HEATED, TILTING KETTLE
WITH NON-TILT OUT INCLINED AGITATOR
3"
32-1/8"
* ALLOW SAFETY VALVE LEVER TO SNAP DOWN.
STOP
AGITATOR SPEED
FORWARD
JOGRUN
START
BACK
HIGH
TILT
E-STOP
START/JOG
HEAT
SIMMER
OFF
* LIFT SAFETY VALVE LEVER TO VENT KETTLE
* HEAT KETTLE UNTIL PRESSURE GAUGE READS 5 PSI.
BETWEEN 20-30 in. Hg BELOW ZERO (WHEN KETTLE IS COLD)
* CHECK FOR VACUUM IN KETTLE. PRESSURE GAUGE SHOULD READ
** WARNING STEAM WILL ESCAPE **
ESTABLISH VACUUM
BEFORE OPERATION
SPEED CONTROL
LOW WATER CUTOFF
POWER
4. 1" NPT GAS SUPPLY
11.
24" SERVICE CLEARANCE REQUIRED
9. APPROX. SHIPPING WEIGHT: 1750 LBS
8. ELECTRIC MOTOR DRIVEN POWER TILT FEATURE
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
10. COLD WATER SUPPLY - 3/4" HOSE CONNECTION
6. 3" AIR ACTUATED BOTTOM DROP DOWN VALVE
7. 2 H.P. VARIABLE SPEED AGITATOR MOTOR
5. 50 PSI ASME APPROVED
KETTLE
2. ELECTRICAL CONNECTION 1/2" CONDUIT
ELECTRICAL SUPPLY VOLTAGE: 208/240/480 VAC
3 PHASE 60 Hz
3.
PRODUCT SPECIFICATIONS:
P/N 115211 REV. E
3/8" NPT AIR SUPPLY: 100 PSI MAX.
C
L
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW REAR VIEW
MOTOR AND BRIDGE ASS'Y. NOT SHOWN IN THIS VIEW
INCOMING GAS SUPPLY
PRESSURES
GAS TYPE
NATURAL
PROPANE
MINIMUM
7" W.C.
11" W.C.
MAXIMUM
14" W.C.
14" W.C.
POWER SUPPLY
VOLTAGE 3 PHASE
208 11 AMPS
240 10 AMPS
--
5 AMPS480
1. INPUT RATE: 360,000 BTU/HR
12.
UNIT MUST BE MOUNTED ON NON-COMBUSTIBLE
FLOORING.
MOUNTING HOLE
FLOOR PATTERN
C
L
KETTLE
13.
PRODUCT OVERFLOW WHEN KETTLE IS STOPPED
DURING TILT CYCLE
14.
42" DRAIN RECOMMENDED
0.34 GPM @ 30 PSI
(SUPPLY 30 PSI MIN. & 60 PSI MAX.)
FULL TILT POSITION
15. RECOMMENDED LOCATION FOR ACCESS TO
4-20 MA FOOD PROBE OUTPUT ON CONTROLLER.
KETTLE
L
C
KETTLE
L
C
64 1/4"
53-3/8"
34"DIA
54 1/4"
31"
3/4" NPT WATER SPOUT
12"
38"
33-3/4"
35-3/4"
12-1/2"
4 10
5"3
2
3-1/2"
2
8
47 13/32
5 1/2
16"
7
6
SEE NOTE 14
71"
6-1/2"
22" MIN. COMBUSTIBLE
MATERIAL CLEARANCE
1-1/2"
2-1/2"
10-1/4"
7/8"
16"
4-5/32"
4"
6-5/8"
11
11
BOTTOM OF BOTH SERVICE ACCESS PANELS
30"
POUR PATH
SEE NOTE 14
4"
SEE NOTE 13
15
15
SELF-CONTAINED, GAS HEATED, TILTING KETTLE
WITH NON-TILT OUT INCLINED AGITATOR
3"
32-1/8"
MaRMITa
C
VIsTa LaTERaL DERECHa VIsTa TRasERa
VIsTa DEsDE aRRIBa
MaRMITa
C
L
MaRMITa
C
L
DIÁM 34"
(86,4 CM)
GRIfO aGUa 3/4" (1,9 CM) NPT
PaRTE BaJa DE LOs PaNELEs DE aCCEsO
PaRa MaNTENIMIENTO
VER NOTa 13
VERTIDO
30" (76,2 CM)
VER NOTa 14
POsICIÓN TOTaLMENTE
INCLINaDa
HUECO MÍN. MaTERIaL
COMBUsTIBLE 22"(56 CM)
CONJUNTO MOTOR Y PUENTE. NO sE MUEsTRa EN EsTa VIsTa.
PLaNTILLa DE
ORIfICIOs DE MONTaJE
VER NOTa 14
14,0 CM
120,4 CM
16,8 CM
10,6 CM
2,2 CM
40,6
CM
10,2 CM
CONJUNTO MOTOR Y PUENTE. NO sE MUEsTRa EN EsTa VIsTa.
EsPECIfICaCIONEs DEL PRODUCTO:
1. fLUJO ENTRaDa: 360.000 BTU/H
2. CONEXIÓN ELÉCTRICa CONDUCTO DE aLIMENTaCIÓN DE
ELECTRICIDaD 1/2" (1,27 CM), TENsIÓN: 208/240/480 VCa
TRIfÁsICa 60 HZ
3. aLIMENTaCIÓN DE aIRE 3/8" (0,9 CM) NPT: MÁX. 100 PsI (6,9
BaREs)
4. aLIMENTaCIÓN DE Gas 1" (2,54 CM) NPT
5. HOMOLOGaCIÓN asME 50 PsI (3,45 BaREs)
6. VÁLVULa NEUMÁTICa DE DEsCaRGa POR EL fONDO 3" (7,62 CM)
7. MOTOR DE aGITaDOR DE VELOCIDaD VaRIaBLE DE 2 CV
8. MOTOR ELÉCTRICO PaRa INCLINaCIÓN
9. PEsO aPROX. DE EXPEDICIÓN: 1750 LBs (794 KG.)
10. aLIMENTaCIÓN aGUa fRÍa: TUBO DE CONEXIÓN 3/4" (1,9 CM)
0,34 GPM (3,8 LITROs/MIN) @ 30 PsI (2,1 BaREs). (aLIMENTaCIÓN
MÍN. 30 PsI (2,1 BaREs) Y MÁX. 60 PsI (4,1 BaREs))
11. HUECO NECEsaRIO PaRa MaNTENIMIENTO 24" (61 CM)
12. La UNIDaD DEBE MONTaRsE sOBRE sUELO NO INfLaMaBLE
13. REBOsE DE PRODUCTO sI sE DETIENE La MaRMITa DURaNTE
EL CICLO DE INCLINaCIÓN
14. sE RECOMIENDa DEsaGÚE 42" (107 CM)
15. EM PLaZaMIENTO RECOMENDaDO PaRa sONDa DE aCCEsO
a aLIMENTOs 4-20 Ma EN CONTROLaDOR
PREsIONEs DE
aLIMENTaCIÓN DE Gas
TIPO DE Gas MÍNIMa MÁXIMa
NaTURaL
17,8 CM
Ca
35,6 CM
Ca
PROPaNO
27,9 CM
Ca
35,6 CM
Ca
aLIMENTaCIÓN DE
RED ELÉCTRICa
TENsIÓN TRIfÁsICa
208 11 aMP.
240 10 aMP.
- -
480 5 aMP.
90,8 CM
31,7 CM
85,7 CM
6,3 CM
3,8 CM
135,6 CM
78,7 CM
11
7
8
11
180,3
CM
6
81,6 CM
163,2 CM
26,0 CM
8,9 CM
16,5 CM
30,5
CM
96,5
CM
137,8 CM
10,2 CM
7,6
CM
15
2
2
15
3
12,7 CM
10"
4
40,6
CM
MaRMITa
C
L
VIsTa fRONTaL
  • Page 1 1
  • Page 2 2

Capkold DHINA2 El manual del propietario

Capkold
Marca
Capkold
Modelo
DHINA2
Tipo
El manual del propietario
Descargar PDF
informe

Documentos relacionados

Otros documentos