PPA Dz Cube 500 Jetflex 24V Manual de usuario

Marca: PPA

Modelo: Dz Cube 500 Jetflex 24V

Categoría: Abridor de puerta

Tipo: Manual de usuario

OPERATOR FOR

GATES

SLIDING | OVERHEAD | PIVOTING

P31264 - 12/2022

Rev. 0

ATTENTION

Do not use the equipment without

reading the instruction manual.

USER MANUAL

Before using the OPERATOR, read and strictly follow all the instructions contained

in this manual.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities or by persons lacking experience and knowledge, unless they have received instructions

on how to use the appliance or are supervised by a person responsible for your safety. It is recommended that

children are supervised and guided, ensuring that they do not play with the product.

It is important for people's safety to follow all instructions. Please keep these

instructions.

-For correct use, read this user manual carefully.

-All data referred to in this manual are for information purposes only.

-PPA reserves the right to modify this information without prior notice.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Important Safety Instructions. Follow all instructions in this manual.

Incorrect installation can lead to serious injury.

-Do not allow children to handle the equipment's remote control. Keep the remote

control away from children, avoiding unnecessary openings and, consequently, reducing

the safety of the place;

-Do not activate the operator, at least when you are sure that there are no children,

animals, objects or obstacles in the path of the gate or in its vicinity;

-Do not automate gates that have built-in pedestrian doors;

-Turn o the mains (power supply) when performing cleaning or any maintenance. Maintenance/installation

of the operators by a PPA specialized technician is mandatory;

-Frequently, examine the installation, security system, xing brackets, mechanical wear, damage or

imbalance, good mechanical condition (proper opening and closing). Periodically clean the gate guide to

prevent it from rusting and requiring more power from the operator. Do not carry out repairs or adaptations

at your own expense. Look for a specialized technician to carry out the repairs, as a failure in the installation

or improper repair can cause injury to the user;

-This appliance is considered suitable for use in countries with a hot climate and constant humidity. It can also

be used in other countries as long as the temperature range described in the technical specications found in

the technical manual available at www.ppa.com.br is respected;

-It is very important to wait for the end of the operator's movement course and keep people away until the

gate is completely open or closed;

WARNING: Gate operator- The gate may operate unexpectedly, so do not allow

anything to get in the way of the mover.

-If the power cord is damaged, ask the specialized technician for its replacement, in order to avoid risks. The

use of the Ground Wire is mandatory;

-Before installation, it is necessary to check, on the identication label, if the temperature range of the

equipment is suitable for the installation location;

-Be careful when using the operator unlocking system for manual movement of the gate;

-Operators must be installed internally and must not move onto public roads.

REMOTE CONTROL

The PPA remote control is made of special and sturdy material. When it is not responding

to commands and the LED signals with reduced intensity or, depending on the model, the LED

changes to red, it may be necessary to change the battery.

When inserting the new battery, observe the polarity (+ and -) indicated on the base of the

transmitter.

Remote control functions:

Depending on the model, PPA remotes have two to four command buttons. In this way, a single control

can open two or more dierent gates.

The remote control functions are descibed below:

Note: To encode the remote control, look for a PPA specialized technician.

OPERATOR FOR SLIDING GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

ATTENTION

Always check the condition of the labels. If the stickers become damaged or

illegible, purchase others from a PPA Dealer.

Shutdown means:

For the total shutdown of the operator, it is necessary to use a shutdown device that must be

incorporated into the xed wiring and located close to the operator.

Examples of total shutdown devices: Circuit breakers, ON/OFF switch, etc.

Note: The total disconnection device incorporated in the xed wiring must guarantee the disconnection

of all mains conductors, except the Earth.

Functioning:

To activate your operator, press

the PPA remote control button that

comes with the machine for 1 second.

If the remote control is activated while the gate is opening, the operator will stop and remain in this way

until the remote control is activated again. When this happens, the gate will be closed

If the remote control is activated while the gate is closing, for safety

reasons, the gate will stop and open automatically.

Unlocking system:

In the event of a power outage, the equipment has an unlocking system that allows you to manually

open and close the gate. To do this, check the model of your operator below:

DZ HOME

1) To operate the gate in manual mode, turn the key in the unlocking hole and move

the gate leaf.

2) To operate the gate in automatic mode, turn the key in the opposite direction.

DZ HUB, DZ CUBE, DZ RIO, DZ RIO NEXUS, DZ PREDIAL, DZ PREDIAL NEXUS, DZ FORT, EURUS 2000,

DZ 1300 IND, DZ 1500 IND, DZ 800 CONDOMINIUM, DZ CONDOMINIUM, DZ 1500 NEXUS, DZ IND 2.2

BRUSHLESS, DZ BRUTALLE

1) To operate the gate in manual mode, turn the key counterclockwise;

2) Move the lever to the left;

3) Move the gate leaf;

4) To operate in automatic mode again, return the handle to the starting position and

turn the key clockwise.

EURUS STEEL

1) To operate the gate in manual mode, remove the

unlocking cover;

2) Turn the key clockwise;

3) Move the lever to the right;

4) Move the gate leaf;

5) To operate in automatic mode again, return the

handle to the starting position, turn the key clockwise

and counterclockwise and t the cover.

DZ IND 2.2 ROBUST HARDWORKING

1) Using a tool, open and remove the front cover;

2) To operate the gate in manual mode, turn the key counterclockwise;

3) Move the lever to the left;

4) Move the gate leaf;

5) To operate in automatic mode again, return the handle to the

starting position and turn the key clockwise and reposition the front

cover.

2500 HARDWORKING

1) To operate in manual mode, remove the front cover by removing

the screw using a 4mm allen wrench;

2) Insert the key and turn it counterclockwise;

3) Move the lever to the left;

4) Move the gate leaf;

5) To operate in automatic mode again, return the handle to the

starting position, turn the key clockwise, re-insert the front cover

and return the xing screw.

LIGER UNIVERSAL

1) To operate the gate in manual mode,

remove the unlocking cover;

2) Unlocking is done by turning the Allen key

6 mm.

DZCT PORTAL

OPERATOR

1) Remove the Cotter pin

from the Unlock Pin

Housing.

2) Remove the Unlocking Pin.

3) Pull back the Unlocking Lever.

4) Manually move the Gate Leaf.

5) To operate in Automatic Mode, carry out the reverse process.

AUTOMATIZADOR DF

1 - Remove the cotter pin from the unlocking pin seat.

2 - Remove the unlocking pin.

3 - Turn the unlocking lever.

4 - Manually move the gate leaf.

5 - to operate in automatic mode, reverse the process.

Command board:

The electronic board allows the installation of other accessories that add functions to the operator and

provide more comfort and safety to the user:

PHOTOCELL: Prevents a person or vehicle from

being caught by surprise on the way to the gate.

When detecting an obstruction in its line of pas-

sage, the photocell (active infrared sensor) prevents the

closing or stops the closing movement by automatically

opening the gate, thus avoiding collision with people,

objects, cars or animals.

GARAGE LIGHT: Turns on the light of the garage where the automation is installed, as soon as it is

activated for opening, making it possible to check if there is someone close to the residence.

The light turns o only after the gate is completely closed, with an adjustable delay time.

SIGNAL: Alerts the pedestrian of the exit or

entry of vehicles in a certain location.

The signal goes into operation when the gate

is activated for opening and turns o as soon as it

is fully closed.

The accessories described above are optional and are not included with the product.

The use of photocells and signals is recommended to increase safety in the operator’s

operation. Contact a representative or visit the website (www.ppa.com.br) to learn

about the models available..

OPERATOR FOR OVERHEAR GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

Identication tag

Slide unlock identication label

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Command

button 1

Command

button 1

Command

button 3

Command

button 2

Command

button 4

Command

button 2

Identication tag

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Overhead unlock identication label

Chave

Alavanca

Conduit

Shutdown device

Key

Lever

Cover

Manual Unlocking

Insert the key into the

lever by turning it

Pull the lever until

the end

Remove the cupula and remove

the down unlocking pin

Lift the lever latch Release the lever

by pushing

OPERATOR FOR

GATES

SLIDING | OVERHEAD | PIVOTING

P31264 - 12/2022

Rev. 0

ATTENTION

Do not use the equipment without

reading the instruction manual.

USER MANUAL

Before using the OPERATOR, read and strictly follow all the instructions contained

in this manual.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities or by persons lacking experience and knowledge, unless they have received instructions

on how to use the appliance or are supervised by a person responsible for your safety. It is recommended that

children are supervised and guided, ensuring that they do not play with the product.

It is important for people's safety to follow all instructions. Please keep these

instructions.

-For correct use, read this user manual carefully.

-All data referred to in this manual are for information purposes only.

-PPA reserves the right to modify this information without prior notice.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Important Safety Instructions. Follow all instructions in this manual.

Incorrect installation can lead to serious injury.

-Do not allow children to handle the equipment's remote control. Keep the remote

control away from children, avoiding unnecessary openings and, consequently, reducing

the safety of the place;

-Do not activate the operator, at least when you are sure that there are no children,

animals, objects or obstacles in the path of the gate or in its vicinity;

-Do not automate gates that have built-in pedestrian doors;

-Turn o the mains (power supply) when performing cleaning or any maintenance. Maintenance/installation

of the operators by a PPA specialized technician is mandatory;

-Frequently, examine the installation, security system, xing brackets, mechanical wear, damage or

imbalance, good mechanical condition (proper opening and closing). Periodically clean the gate guide to

prevent it from rusting and requiring more power from the operator. Do not carry out repairs or adaptations

at your own expense. Look for a specialized technician to carry out the repairs, as a failure in the installation

or improper repair can cause injury to the user;

-This appliance is considered suitable for use in countries with a hot climate and constant humidity. It can also

be used in other countries as long as the temperature range described in the technical specications found in

the technical manual available at www.ppa.com.br is respected;

-It is very important to wait for the end of the operator's movement course and keep people away until the

gate is completely open or closed;

WARNING: Gate operator- The gate may operate unexpectedly, so do not allow

anything to get in the way of the mover.

-If the power cord is damaged, ask the specialized technician for its replacement, in order to avoid risks. The

use of the Ground Wire is mandatory;

-Before installation, it is necessary to check, on the identication label, if the temperature range of the

equipment is suitable for the installation location;

-Be careful when using the operator unlocking system for manual movement of the gate;

-Operators must be installed internally and must not move onto public roads.

REMOTE CONTROL

The PPA remote control is made of special and sturdy material. When it is not responding

to commands and the LED signals with reduced intensity or, depending on the model, the LED

changes to red, it may be necessary to change the battery.

When inserting the new battery, observe the polarity (+ and -) indicated on the base of the

transmitter.

Remote control functions:

Depending on the model, PPA remotes have two to four command buttons. In this way, a single control

can open two or more dierent gates.

The remote control functions are descibed below:

Note: To encode the remote control, look for a PPA specialized technician.

OPERATOR FOR SLIDING GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

ATTENTION

Always check the condition of the labels. If the stickers become damaged or

illegible, purchase others from a PPA Dealer.

Shutdown means:

For the total shutdown of the operator, it is necessary to use a shutdown device that must be

incorporated into the xed wiring and located close to the operator.

Examples of total shutdown devices: Circuit breakers, ON/OFF switch, etc.

Note: The total disconnection device incorporated in the xed wiring must guarantee the disconnection

of all mains conductors, except the Earth.

Functioning:

To activate your operator, press

the PPA remote control button that

comes with the machine for 1 second.

If the remote control is activated while the gate is opening, the operator will stop and remain in this way

until the remote control is activated again. When this happens, the gate will be closed

If the remote control is activated while the gate is closing, for safety

reasons, the gate will stop and open automatically.

Unlocking system:

In the event of a power outage, the equipment has an unlocking system that allows you to manually

open and close the gate. To do this, check the model of your operator below:

DZ HOME

1) To operate the gate in manual mode, turn the key in the unlocking hole and move

the gate leaf.

2) To operate the gate in automatic mode, turn the key in the opposite direction.

DZ HUB, DZ CUBE, DZ RIO, DZ RIO NEXUS, DZ PREDIAL, DZ PREDIAL NEXUS, DZ FORT, EURUS 2000,

DZ 1300 IND, DZ 1500 IND, DZ 800 CONDOMINIUM, DZ CONDOMINIUM, DZ 1500 NEXUS, DZ IND 2.2

BRUSHLESS, DZ BRUTALLE

1) To operate the gate in manual mode, turn the key counterclockwise;

2) Move the lever to the left;

3) Move the gate leaf;

4) To operate in automatic mode again, return the handle to the starting position and

turn the key clockwise.

EURUS STEEL

1) To operate the gate in manual mode, remove the

unlocking cover;

2) Turn the key clockwise;

3) Move the lever to the right;

4) Move the gate leaf;

5) To operate in automatic mode again, return the

handle to the starting position, turn the key clockwise

and counterclockwise and t the cover.

DZ IND 2.2 ROBUST HARDWORKING

1) Using a tool, open and remove the front cover;

2) To operate the gate in manual mode, turn the key counterclockwise;

3) Move the lever to the left;

4) Move the gate leaf;

5) To operate in automatic mode again, return the handle to the

starting position and turn the key clockwise and reposition the front

cover.

2500 HARDWORKING

1) To operate in manual mode, remove the front cover by removing

the screw using a 4mm allen wrench;

2) Insert the key and turn it counterclockwise;

3) Move the lever to the left;

4) Move the gate leaf;

5) To operate in automatic mode again, return the handle to the

starting position, turn the key clockwise, re-insert the front cover

and return the xing screw.

LIGER UNIVERSAL

1) To operate the gate in manual mode,

remove the unlocking cover;

2) Unlocking is done by turning the Allen key

6 mm.

DZCT PORTAL

OPERATOR

1) Remove the Cotter pin

from the Unlock Pin

Housing.

2) Remove the Unlocking Pin.

3) Pull back the Unlocking Lever.

4) Manually move the Gate Leaf.

5) To operate in Automatic Mode, carry out the reverse process.

AUTOMATIZADOR DF

1 - Remove the cotter pin from the unlocking pin seat.

2 - Remove the unlocking pin.

3 - Turn the unlocking lever.

4 - Manually move the gate leaf.

5 - to operate in automatic mode, reverse the process.

Command board:

The electronic board allows the installation of other accessories that add functions to the operator and

provide more comfort and safety to the user:

PHOTOCELL: Prevents a person or vehicle from

being caught by surprise on the way to the gate.

When detecting an obstruction in its line of pas-

sage, the photocell (active infrared sensor) prevents the

closing or stops the closing movement by automatically

opening the gate, thus avoiding collision with people,

objects, cars or animals.

GARAGE LIGHT: Turns on the light of the garage where the automation is installed, as soon as it is

activated for opening, making it possible to check if there is someone close to the residence.

The light turns o only after the gate is completely closed, with an adjustable delay time.

SIGNAL: Alerts the pedestrian of the exit or

entry of vehicles in a certain location.

The signal goes into operation when the gate

is activated for opening and turns o as soon as it

is fully closed.

The accessories described above are optional and are not included with the product.

The use of photocells and signals is recommended to increase safety in the operator’s

operation. Contact a representative or visit the website (www.ppa.com.br) to learn

about the models available..

OPERATOR FOR OVERHEAR GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

Identication tag

Slide unlock identication label

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Command

button 1

Command

button 1

Command

button 3

Command

button 2

Command

button 4

Command

button 2

Identication tag

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Overhead unlock identication label

Chave

Alavanca

Conduit

Shutdown device

Key

Lever

Cover

Manual Unlocking

Insert the key into the

lever by turning it

Pull the lever until

the end

Remove the cupula and remove

the down unlocking pin

Lift the lever latch Release the lever

by pushing

OPERATOR FOR

GATES

SLIDING | OVERHEAD | PIVOTING

P31264 - 12/2022

Rev. 0

ATTENTION

Do not use the equipment without

reading the instruction manual.

USER MANUAL

Before using the OPERATOR, read and strictly follow all the instructions contained

in this manual.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities or by persons lacking experience and knowledge, unless they have received instructions

on how to use the appliance or are supervised by a person responsible for your safety. It is recommended that

children are supervised and guided, ensuring that they do not play with the product.

It is important for people's safety to follow all instructions. Please keep these

instructions.

-For correct use, read this user manual carefully.

-All data referred to in this manual are for information purposes only.

-PPA reserves the right to modify this information without prior notice.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Important Safety Instructions. Follow all instructions in this manual.

Incorrect installation can lead to serious injury.

-Do not allow children to handle the equipment's remote control. Keep the remote

control away from children, avoiding unnecessary openings and, consequently, reducing

the safety of the place;

-Do not activate the operator, at least when you are sure that there are no children,

animals, objects or obstacles in the path of the gate or in its vicinity;

-Do not automate gates that have built-in pedestrian doors;

-Turn o the mains (power supply) when performing cleaning or any maintenance. Maintenance/installation

of the operators by a PPA specialized technician is mandatory;

-Frequently, examine the installation, security system, xing brackets, mechanical wear, damage or

imbalance, good mechanical condition (proper opening and closing). Periodically clean the gate guide to

prevent it from rusting and requiring more power from the operator. Do not carry out repairs or adaptations

at your own expense. Look for a specialized technician to carry out the repairs, as a failure in the installation

or improper repair can cause injury to the user;

-This appliance is considered suitable for use in countries with a hot climate and constant humidity. It can also

be used in other countries as long as the temperature range described in the technical specications found in

the technical manual available at www.ppa.com.br is respected;

-It is very important to wait for the end of the operator's movement course and keep people away until the

gate is completely open or closed;

WARNING: Gate operator- The gate may operate unexpectedly, so do not allow

anything to get in the way of the mover.

-If the power cord is damaged, ask the specialized technician for its replacement, in order to avoid risks. The

use of the Ground Wire is mandatory;

-Before installation, it is necessary to check, on the identication label, if the temperature range of the

equipment is suitable for the installation location;

-Be careful when using the operator unlocking system for manual movement of the gate;

-Operators must be installed internally and must not move onto public roads.

REMOTE CONTROL

The PPA remote control is made of special and sturdy material. When it is not responding

to commands and the LED signals with reduced intensity or, depending on the model, the LED

changes to red, it may be necessary to change the battery.

When inserting the new battery, observe the polarity (+ and -) indicated on the base of the

transmitter.

Remote control functions:

Depending on the model, PPA remotes have two to four command buttons. In this way, a single control

can open two or more dierent gates.

The remote control functions are descibed below:

Note: To encode the remote control, look for a PPA specialized technician.

OPERATOR FOR SLIDING GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

ATTENTION

Always check the condition of the labels. If the stickers become damaged or

illegible, purchase others from a PPA Dealer.

Shutdown means:

For the total shutdown of the operator, it is necessary to use a shutdown device that must be

incorporated into the xed wiring and located close to the operator.

Examples of total shutdown devices: Circuit breakers, ON/OFF switch, etc.

Note: The total disconnection device incorporated in the xed wiring must guarantee the disconnection

of all mains conductors, except the Earth.

Functioning:

To activate your operator, press

the PPA remote control button that

comes with the machine for 1 second.

If the remote control is activated while the gate is opening, the operator will stop and remain in this way

until the remote control is activated again. When this happens, the gate will be closed

If the remote control is activated while the gate is closing, for safety

reasons, the gate will stop and open automatically.

Unlocking system:

In the event of a power outage, the equipment has an unlocking system that allows you to manually

open and close the gate. To do this, check the model of your operator below:

DZ HOME

1) To operate the gate in manual mode, turn the key in the unlocking hole and move

the gate leaf.

2) To operate the gate in automatic mode, turn the key in the opposite direction.

DZ HUB, DZ CUBE, DZ RIO, DZ RIO NEXUS, DZ PREDIAL, DZ PREDIAL NEXUS, DZ FORT, EURUS 2000,

DZ 1300 IND, DZ 1500 IND, DZ 800 CONDOMINIUM, DZ CONDOMINIUM, DZ 1500 NEXUS, DZ IND 2.2

BRUSHLESS, DZ BRUTALLE

1) To operate the gate in manual mode, turn the key counterclockwise;

2) Move the lever to the left;

3) Move the gate leaf;

4) To operate in automatic mode again, return the handle to the starting position and

turn the key clockwise.

EURUS STEEL

1) To operate the gate in manual mode, remove the

unlocking cover;

2) Turn the key clockwise;

3) Move the lever to the right;

4) Move the gate leaf;

5) To operate in automatic mode again, return the

handle to the starting position, turn the key clockwise

and counterclockwise and t the cover.

DZ IND 2.2 ROBUST HARDWORKING

1) Using a tool, open and remove the front cover;

2) To operate the gate in manual mode, turn the key counterclockwise;

3) Move the lever to the left;

4) Move the gate leaf;

5) To operate in automatic mode again, return the handle to the

starting position and turn the key clockwise and reposition the front

cover.

2500 HARDWORKING

1) To operate in manual mode, remove the front cover by removing

the screw using a 4mm allen wrench;

2) Insert the key and turn it counterclockwise;

3) Move the lever to the left;

4) Move the gate leaf;

5) To operate in automatic mode again, return the handle to the

starting position, turn the key clockwise, re-insert the front cover

and return the xing screw.

LIGER UNIVERSAL

1) To operate the gate in manual mode,

remove the unlocking cover;

2) Unlocking is done by turning the Allen key

6 mm.

DZCT PORTAL

OPERATOR

1) Remove the Cotter pin

from the Unlock Pin

Housing.

2) Remove the Unlocking Pin.

3) Pull back the Unlocking Lever.

4) Manually move the Gate Leaf.

5) To operate in Automatic Mode, carry out the reverse process.

AUTOMATIZADOR DF

1 - Remove the cotter pin from the unlocking pin seat.

2 - Remove the unlocking pin.

3 - Turn the unlocking lever.

4 - Manually move the gate leaf.

5 - to operate in automatic mode, reverse the process.

Command board:

The electronic board allows the installation of other accessories that add functions to the operator and

provide more comfort and safety to the user:

PHOTOCELL: Prevents a person or vehicle from

being caught by surprise on the way to the gate.

When detecting an obstruction in its line of pas-

sage, the photocell (active infrared sensor) prevents the

closing or stops the closing movement by automatically

opening the gate, thus avoiding collision with people,

objects, cars or animals.

GARAGE LIGHT: Turns on the light of the garage where the automation is installed, as soon as it is

activated for opening, making it possible to check if there is someone close to the residence.

The light turns o only after the gate is completely closed, with an adjustable delay time.

SIGNAL: Alerts the pedestrian of the exit or

entry of vehicles in a certain location.

The signal goes into operation when the gate

is activated for opening and turns o as soon as it

is fully closed.

The accessories described above are optional and are not included with the product.

The use of photocells and signals is recommended to increase safety in the operator’s

operation. Contact a representative or visit the website (www.ppa.com.br) to learn

about the models available..

OPERATOR FOR OVERHEAR GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

Identication tag

Slide unlock identication label

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Command

button 1

Command

button 1

Command

button 3

Command

button 2

Command

button 4

Command

button 2

Identication tag

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Overhead unlock identication label

Chave

Alavanca

Conduit

Shutdown device

Key

Lever

Cover

Manual Unlocking

Insert the key into the

lever by turning it

Pull the lever until

the end

Remove the cupula and remove

the down unlocking pin

Lift the lever latch Release the lever

by pushing

OPERATOR FOR

GATES

SLIDING | OVERHEAD | PIVOTING

P31264 - 12/2022

Rev. 0

ATTENTION

Do not use the equipment without

reading the instruction manual.

USER MANUAL

Before using the OPERATOR, read and strictly follow all the instructions contained

in this manual.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities or by persons lacking experience and knowledge, unless they have received instructions

on how to use the appliance or are supervised by a person responsible for your safety. It is recommended that

children are supervised and guided, ensuring that they do not play with the product.

It is important for people's safety to follow all instructions. Please keep these

instructions.

-For correct use, read this user manual carefully.

-All data referred to in this manual are for information purposes only.

-PPA reserves the right to modify this information without prior notice.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Important Safety Instructions. Follow all instructions in this manual.

Incorrect installation can lead to serious injury.

-Do not allow children to handle the equipment's remote control. Keep the remote

control away from children, avoiding unnecessary openings and, consequently, reducing

the safety of the place;

-Do not activate the operator, at least when you are sure that there are no children,

animals, objects or obstacles in the path of the gate or in its vicinity;

-Do not automate gates that have built-in pedestrian doors;

-Turn o the mains (power supply) when performing cleaning or any maintenance. Maintenance/installation

of the operators by a PPA specialized technician is mandatory;

-Frequently, examine the installation, security system, xing brackets, mechanical wear, damage or

imbalance, good mechanical condition (proper opening and closing). Periodically clean the gate guide to

prevent it from rusting and requiring more power from the operator. Do not carry out repairs or adaptations

at your own expense. Look for a specialized technician to carry out the repairs, as a failure in the installation

or improper repair can cause injury to the user;

-This appliance is considered suitable for use in countries with a hot climate and constant humidity. It can also

be used in other countries as long as the temperature range described in the technical specications found in

the technical manual available at www.ppa.com.br is respected;

-It is very important to wait for the end of the operator's movement course and keep people away until the

gate is completely open or closed;

WARNING: Gate operator- The gate may operate unexpectedly, so do not allow

anything to get in the way of the mover.

-If the power cord is damaged, ask the specialized technician for its replacement, in order to avoid risks. The

use of the Ground Wire is mandatory;

-Before installation, it is necessary to check, on the identication label, if the temperature range of the

equipment is suitable for the installation location;

-Be careful when using the operator unlocking system for manual movement of the gate;

-Operators must be installed internally and must not move onto public roads.

REMOTE CONTROL

The PPA remote control is made of special and sturdy material. When it is not responding

to commands and the LED signals with reduced intensity or, depending on the model, the LED

changes to red, it may be necessary to change the battery.

When inserting the new battery, observe the polarity (+ and -) indicated on the base of the

transmitter.

Remote control functions:

Depending on the model, PPA remotes have two to four command buttons. In this way, a single control

can open two or more dierent gates.

The remote control functions are descibed below:

Note: To encode the remote control, look for a PPA specialized technician.

OPERATOR FOR SLIDING GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

ATTENTION

Always check the condition of the labels. If the stickers become damaged or

illegible, purchase others from a PPA Dealer.

Shutdown means:

For the total shutdown of the operator, it is necessary to use a shutdown device that must be

incorporated into the xed wiring and located close to the operator.

Examples of total shutdown devices: Circuit breakers, ON/OFF switch, etc.

Note: The total disconnection device incorporated in the xed wiring must guarantee the disconnection

of all mains conductors, except the Earth.

Functioning:

To activate your operator, press

the PPA remote control button that

comes with the machine for 1 second.

If the remote control is activated while the gate is opening, the operator will stop and remain in this way

until the remote control is activated again. When this happens, the gate will be closed

If the remote control is activated while the gate is closing, for safety

reasons, the gate will stop and open automatically.

Unlocking system:

In the event of a power outage, the equipment has an unlocking system that allows you to manually

open and close the gate. To do this, check the model of your operator below:

DZ HOME

1) To operate the gate in manual mode, turn the key in the unlocking hole and move

the gate leaf.

2) To operate the gate in automatic mode, turn the key in the opposite direction.

DZ HUB, DZ CUBE, DZ RIO, DZ RIO NEXUS, DZ PREDIAL, DZ PREDIAL NEXUS, DZ FORT, EURUS 2000,

DZ 1300 IND, DZ 1500 IND, DZ 800 CONDOMINIUM, DZ CONDOMINIUM, DZ 1500 NEXUS, DZ IND 2.2

BRUSHLESS, DZ BRUTALLE

1) To operate the gate in manual mode, turn the key counterclockwise;

2) Move the lever to the left;

3) Move the gate leaf;

4) To operate in automatic mode again, return the handle to the starting position and

turn the key clockwise.

EURUS STEEL

1) To operate the gate in manual mode, remove the

unlocking cover;

2) Turn the key clockwise;

3) Move the lever to the right;

4) Move the gate leaf;

5) To operate in automatic mode again, return the

handle to the starting position, turn the key clockwise

and counterclockwise and t the cover.

DZ IND 2.2 ROBUST HARDWORKING

1) Using a tool, open and remove the front cover;

2) To operate the gate in manual mode, turn the key counterclockwise;

3) Move the lever to the left;

4) Move the gate leaf;

5) To operate in automatic mode again, return the handle to the

starting position and turn the key clockwise and reposition the front

cover.

2500 HARDWORKING

1) To operate in manual mode, remove the front cover by removing

the screw using a 4mm allen wrench;

2) Insert the key and turn it counterclockwise;

3) Move the lever to the left;

4) Move the gate leaf;

5) To operate in automatic mode again, return the handle to the

starting position, turn the key clockwise, re-insert the front cover

and return the xing screw.

LIGER UNIVERSAL

1) To operate the gate in manual mode,

remove the unlocking cover;

2) Unlocking is done by turning the Allen key

6 mm.

DZCT PORTAL

OPERATOR

1) Remove the Cotter pin

from the Unlock Pin

Housing.

2) Remove the Unlocking Pin.

3) Pull back the Unlocking Lever.

4) Manually move the Gate Leaf.

5) To operate in Automatic Mode, carry out the reverse process.

AUTOMATIZADOR DF

1 - Remove the cotter pin from the unlocking pin seat.

2 - Remove the unlocking pin.

3 - Turn the unlocking lever.

4 - Manually move the gate leaf.

5 - to operate in automatic mode, reverse the process.

Command board:

The electronic board allows the installation of other accessories that add functions to the operator and

provide more comfort and safety to the user:

PHOTOCELL: Prevents a person or vehicle from

being caught by surprise on the way to the gate.

When detecting an obstruction in its line of pas-

sage, the photocell (active infrared sensor) prevents the

closing or stops the closing movement by automatically

opening the gate, thus avoiding collision with people,

objects, cars or animals.

GARAGE LIGHT: Turns on the light of the garage where the automation is installed, as soon as it is

activated for opening, making it possible to check if there is someone close to the residence.

The light turns o only after the gate is completely closed, with an adjustable delay time.

SIGNAL: Alerts the pedestrian of the exit or

entry of vehicles in a certain location.

The signal goes into operation when the gate

is activated for opening and turns o as soon as it

is fully closed.

The accessories described above are optional and are not included with the product.

The use of photocells and signals is recommended to increase safety in the operator’s

operation. Contact a representative or visit the website (www.ppa.com.br) to learn

about the models available..

OPERATOR FOR OVERHEAR GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

Identication tag

Slide unlock identication label

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Command

button 1

Command

button 1

Command

button 3

Command

button 2

Command

button 4

Command

button 2

Identication tag

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Overhead unlock identication label

Chave

Alavanca

Conduit

Shutdown device

Key

Lever

Cover

Manual Unlocking

Insert the key into the

lever by turning it

Pull the lever until

the end

Remove the cupula and remove

the down unlocking pin

Lift the lever latch Release the lever

by pushing

ATTENTION

For greater

security,

replace the

cotter pin with

a padlock.

ATTENTION

Always check the condition of the labels. If the stickers become damaged or

illegible, purchase others from a PPA Dealer.

Equipment shutdown:

For the total shutdown of the operator, it is necessary to use a shutdown device that must be

incorporated into the xed wiring and located close to the operator.

Examples of total shutdown devices: Circuit breakers, ON/OFF switch, etc.

Note: The total disconnection device incorporated in the xed wiring must guarantee the disconnection

of all mains conductors, except the Earth.

Functioning:

To activate your

automation, press the PPA

remote control button

that comes with the

machine for 1 second.

If the remote control is activated while the gate is opening, the operator will stop and remain in this way

until the remote control is activated again. When this happens, the gate will be closed.

If the remote control is

activated while the gate is closing,

for safety reasons, the gate will

stop and open automatically.

Unlocking syem:

In the event of a power outage, the equipment has an unlocking syem that allows you to

manually open and close the gate. To do this, check your operator model below:

PISTON SHARK

To operate the gate in manual mode:

1) Remove the protective cover from the unlocking hole;

2) Insert the key;

3) Turn the key 90° (a quarter turn) clockwise;

4) Raise the lever completely;

5) Move the gate leaf;

6) To operate in automatic mode again, return the lever to its original position, turn the key

counterclockwise and insert the protective cap of the unlocking hole back in.

ATTENTION

Always check the condition of the labels. If the stickers become damaged or

illegible, purchase others from a PPA Dealer.

Equipment shutdown:

For the total shutdown of the operator, it is necessary to use a shutdown device that must be

incorporated into the xed wiring and located close to the operator.

Examples of total shutdown devices: Circuit breakers, ON/OFF switch, etc.

Note: The total disconnection device incorporated in the xed wiring must guarantee the disconnection

of all mains conductors, except the Earth.

Functioning:

To activate your operator, press the PPA remote control button that comes with the machine for 1

second.

If the remote control is activated while the gate is opening, the operator will stop and remain in this way

until the remote control is activated again. When this happens, the gate will be closed.

If the remote control is activated while the gate is closing, for safety

reasons, the gate will stop and open automatically.

Unlocking system:

In the event of a power outage, the equipment has an unlocking system that allows you to manually

open and close the gate. To do this, check your operator model below:

VERTICAL OVERHEAD OPERATOR UNLOCKING BV PRIME

To operate the gate in manual mode:

1) Remove the protective cover from the unlocking hole;

2) Insert the key;

3) Turn the key 90° (a quarter turn) clockwise;

4) Raise the lever completely;

5) Move the gate leaf;

6) To operate in automatic mode again, return the lever to its original position, turn the key

counterclockwise and insert the protective cap of the unlocking hole back in.

AUTOMATIZER WITH UNLOCKING SYSTEM BY COTTER PIN OR PADLOCK

1) To operate the gate in manual mode, remove the cotter pin;

2) Remove the unlocking pin;

3) Move the lever tongue upwards;

4) Release the lever by pushing it down.

5) To operate in automatic mode again, ret the lever and pawl on the drive nut pin, insert the pin and

nally the cotter pin.

HORIZONTAL OVERHEAD OPERATOR

1) To operate the gate in manual mode, pull

the release cord downwards;

2) Firmly pull the cord away from the gate;

3) Move the gate leaf;

4) To operate in automatic mode again,

perform the reverse procedure, pulling the cord

towards the gate.

BH POWER CHAIN OPERATOR

1) To operate the gate in manual mode, pull the

release cord downwards so that the trigger is parked in

an upright position.

2) Move the gate manually.

3) To operate in automatic mode again, perform the

reverse procedure.

TORSION OPERATOR

1) To operate the gate in manual mode, turn the

unlocking lever clockwise (upwards) so that the lever is in

the vertical position.

2) Move the gate manually.

3) To operate in automatic mode again, perform the

reverse procedure.

Command board:

The electronic board allows the installation of other accessories that add functions to the operator and

provide more comfort and safety to the user:

Photocell: Prevents a person or vehicle from

being caught by surprise on the way to the gate.

When detecting an obstruction in its

line of passage, the photocell (active infrared

sensor) prevents the closing or stops the closing

movement, automatically opening the gate, thus

avoiding collision with people, objects, cars or

animals.

Garage light: Turns on the light of the garage where the operator is installed, as soon as it is activated

for opening, making it possible to check if there is any individual close to the residence.

The light turns o only after the gate is completely closed, with an adjustable delay time.

Signal: Alerts the pedestrian of the exit or

entry of vehicles in a certain location.

The signal comes on when the gate is

activated for opening and turns o as soon as it is

fully closed.

The accessories described above are optional and are not included with the product.

The use of photocells and signals is recommended to increase safety in the operator’s

operation. Contact a representative or visit the website (www.ppa.com.br) to learn

about the models available.

OPERATORS FOR SWING GATES

Equipment identication:

For greater user safety, the PPA OPERATOR has some marking, identication and attention labels.

DESTRAVADO

TRAVADO

Made by: Motoppar Indústria e Comércio de Automatizadores Ltda

Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil

CNPJ: 52.605.821/0001-55

www.ppa.com.br | +55 14 3407 1000

1) To operate the gate in manual mode, t the key in the unlocking hole with the latch facing

upwards;

2) Turn the key, moving it downwards by 180°, so that the latch is facing downwards;

3) To operate in automatic mode again, turn the key in the opposite direction, turning it up.

Command board:

The electronic board allows the installation of other accessories that add functions to the operator and

provide more comfort and safety to the user:

Fotocélula: Photocell:

Prevents a person or vehicle

from being caught by

surprise on the way to the

gate.

When detecting an obstruction in its line of passage, the photocell (active infrared sensor) prevents the

closing or stops the closing movement by automatically opening the gate, thus avoiding collision with people,

objects, cars or animals.

Garage light: Turns on the light of the garage where the automation is installed, as soon as it is

activated for opening, making it possible to check if there is any individual close to the residence.

The light turns o only after the gate is completely closed, with an adjustable delay time.

Signal: Alerts the pedestrian of the exit or entry of vehicles in a certain location.

The signal goes into operation when the gate is activated to open and turns o as soon as it is fully

closed.

The accessories described above are optional and are not included with the product.

The use of photocells and signals is recommended to increase safety in the operator’s

operation. Contact a representative or visit the website (www.ppa.com.br) to see the

models available.

Identication tag

CODE

MODEL

LOT

WINDING

INSULATION Class

RATED VOLTAGE

NOMINAL CHAIN

RATED POWER

NOMINAL FREQUENCY

TEMPERATURE RANGE

OPERATION

CYCLE cycles/h

NOMINAL LOAD

TIME OF OPERATIONS

LINEAR SPEED

DEGREE OF PROTECTION

WARNING

Automatic activation

Keep away from the drive area as it may move

unexpectedly.

Manual Unlocked

Step 1: Remove the protective cover from

the unlocking hole.

Step 2: Insert the key

Step 3: Turn the key 90° clockwise. Step 4: Raise the lever completely.

Swing unlocking identication label

(depending on the operator model) PIVO HOME PIVO AVIÃO

PIVO PISTON PREDIAL E

PIVO CONDOMINIUM

Conduit

Shutdown device

Lever

Cotter pin

Unlock pin

UNLOCKED

GENERAL TERMS AND CONDITIONS OF WARRANTY

MOTOPPAR, Indury and Commerce of Automatic Gate Operators Ltd., regiered with the CNPJ (National Regiry of

Legal Entities) under Number 52.605.821/0001-55, located at 3526 Dr. Labieno da Coa Machado Avenue, Indurial

Dirict, Garça – SP – Brazil, Zip Code 17400-000, manufacturer of PPA Products, hereby guarantees this product

again design, manufacturing or assembly defects and/or supportively as a result of material quality aws that could

make its intended use improper or inadequate, within a legal period of ninety days from time of acquisition, provided

that the inallation inructions described in the inruction manual are observed.

Due to the credibility and tru placed on PPA products, we will add 275 more days to the period mentioned above,

reaching a warranty period of one year, likewise counted from the time of acquisition proven by consumer through

proof of purchase (Cuomer Receipt).

In case of defect, within the warranty period, PPA responsibilities are rericted to the repair or subitution of the

product manufactured by the company, under the following conditions:

1. Repair and readjument of equipment may only be carried out by PPA Technical Assiance, which is qualied to

open, remove, and subitute parts or components, as well as repair defects covered by this warranty; thus, failure

on observing this guideline and the veried use of any non-original parts will cause the resignation of this warranty

on the part of the user;

2. The warranty will not extend to accessories such as cables, screw kit, xing brackets, power supplies etc.;

3. Expenses for packaging, transportation and product reinallation will be sole responsibility of the consumer;

4. The equipment mu be sent directly to the Company responsible for the sale (manufacturer's representative),

through the address contained in the purchase invoice, properly packed, thus avoiding loss of the warranty;

5. Within the additional period of 275 days, visits and transportation in places where authorized technical assiance is

not available will be charged. The co of transportation of the product and/or technician will be sole responsibility

of the consumer and

6. The subitution or repair of the product does not prolong the warranty time.

This warranty will be terminated if the product:

1. Is damaged by natural agents, such as atmospheric discharges, oods, wildres, landslides etc.;

2. Is inalled in an improper electric power supply or if it is not according to any of the inallation inructions

displayed on the manual;

3. Shows defects caused by droppings, collisions or any other physical accident;

4. Shows signs of product violation or attempted repair by unauthorized personnel;

5. Is not used for its intended purpose;

6. Is not used under normal conditions;

7. Is damaged by accessories or equipment connected to it.

Recommendation:

We recommend that both the inallation and the maintenance of the operator to be performed by an authorized

PPA technical service. If the product fails or has an improper operation, seek an Authorized Technical Service to x it.

Insert the key into the

lever by turning it

Manual Unlocking

Step 1: Fit the key into the hole,

with the tab facing up.

2 Step: turn the key down 180º so

that the latch is facing down.