2999-18
Call Us First!
DO NOT RETURN TO STORE.
For immediate help with assembly or product information
Call our toll-free number:
1-866-890-2211
April through October M - F 8:00 AM to 6:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
or email:
customerservice@backyard-play.com
Our staff is ready to provide assistance.
- NOTICE -
This playset product is not intended for public use. It is intended for
residential application and is not warranted for public or commercial use.
STOP!
STOP!
(This page intentionally left blank.)
02/18/2018
- BEFORE YOU BEGIN -
Your premium playset is manufactured from wood which has many natural characteristics and blemishes that may be present in some of the pieces in your playset. These natural characteristics may include knots or mi-
nor cracks/splits. All individual parts have been cut to provide a smooth and safe surface. All parts have been inspected to assure we pack only the safest, most durable wood product. Any minor blemishes in your playset
will not affect the strength, durability, or structural integrity of the nished product. Our limited warranty does not cover the imperfections not resulting in structural failure.
2999-18
Playset
First...
Check with your homeowner’s association before
assembling.
Read instructions thoroughly before you begin. If you
have purchased accessories to accompany this play
set, please read all installation instructions before
beginning assembly of this structure.
Check All Parts
If a part is missing, circle the part in question and call.
Important
In a drawing, a dotted line represents a part hidden
from view (like a part under a panel).
Adult Assistance required
Assistance is necessary to handle, t
and secure some components.
Squareness is very Important!
Start with a level surface and keep 90° corners and 90°
perpendiculars throughout the assembly to ensure all
components t together.
Safety!
Check for protruding screws and bolts, verify all screw
and bolt lengths during assembly.
Always wear OSHA-APPROVED safety
glasses throughout assembly process.
Tools Required
Socket Set
Hammer
9/16" Combination
Wrench
3/16" Allen Wrench
#2 Square Drive
Bit
T-20 Torque Drive
Bit
#3 Phillips Bit
Cordless Drill
w/Charger
1/8" Drill Bit
7/16" Drill Bit
1/4" Drill Bit
3/8" Drill Bit
Tape Measure
Level
C - Clamps
8' Step Ladder
Framing/Speed
Square
- BEFORE YOU BEGIN -
Recommended for Ages 3 to 11
Backyard Play Systems
Customer Service
1-866-890-2211
1000 Ternes Drive
Monroe, MI 48162
- NOTICE -
This playset product is not intended for public use. It is intended for
residential application and is not warranted for public or commercial use.
Model 4429
2
Wear safety glasses during drilling, assembly of your playset.
Children should not be allowed in the playset assembly and build area.
Note the hole orientation on parts to avoid having to take parts
apart later.
Some steps require the assistance of two people to ensure proper
assembly, safety during assembly, as well as preventing any damage
to the playset.
All hex bolts and lag bolts require a lock washer or lock nut.
To properly install lock nuts, two to three threads must protrude past the
lock nut and be exposed once tightened.
Due to wood characteristics and the manufacturing process hex bolts
may protrude past a surface. If this condition occurs add additional
supplied washers to eliminate bolt protrusion.
To aid in proper assembly pound T-nuts into their respective hole
prior to assembly
Pound in T-nuts while the part is on the ground to ensure proper seating.
Use a soft material under parts when pounding in T-nuts to ensure
no scratching or de-facing of parts.
Make sure all fasteners used are as specied. Using a fastener not
specied in a particular application may result in too much thread
exposure or not enough thread engagement.
ASSEMBLY SAFETY and HELPFUL HINTS
STOP!!! Check all parts and hardware before beginning. If any parts are
missing or damaged please circle and call the phone number listed.
DO NOT CONTACT THE STORE OR RETURN YOUR PLAYSET !
KEEP THIS INSTALLATION MANUAL FOR FUTURE CARE
AND MAINTENANCE REFERENCE.
To aid in making your playset assembly easier,
here is a listing of some helpful hints.
*IMPORTANT HARDWARE INFORMATION*
3
SAFETY WARNINGS
This playset has been designed for use by a maximum of 12 occupants at one time having a
combined weight of 1,260 pounds. (This weight does not include occupants in the sandbox area.)
This playset is recommended for children (3) through (11) years of age.
On-site adult supervision for children of all ages is recommended.
Instruct children not to walk close to, in front of, behind, or between moving items.
Instruct children not to twist swing chains or ropes or loop them over the top support bar since this may
reduce the strength of the chain or rope.
Instruct children to avoid swinging empty seats.
Teach children to sit in the center of the swings with their full weight on the seats.
Instruct children not to use the equipment in a manner other than intended.
Instruct children not to get off equipment while it is in motion.
Parents should dress children appropriately (examples would include the use of well-tting shoes and
the avoidance of ponchos, scarves, and other loose-tting clothing that is potentially hazardous
while using equipment).
Instruct children not to climb when the equipment is wet. Slippery surfaces may cause a hazard.
Verify that suspended climbing ropes, chain, or cable are secured at both ends.
Verify that suspended climbing ropes, chain, or cable cannot be looped back on itself.
Instruct children not to attach items to the playground equipment that are not specically designed for
use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and
chain as they may cause a strangulation hazard.
Instruct children to remove their bike or other sports helmet before playing on the playground equipment.
Instruct children to not walk or run up slides.
Instruct children to not pick up slides or ramps as this may cause damage or breakage.
Place the equipment on level ground not less than six (6) feet from any obstructions. Be sure to look
overhead for any obstructions above the playset.
Do not use the equipment until fully erected per this playset instruction manual, bolts tightened and
the playset is anchored to the ground.
NOTICE:
This playset product is not intended for public use. It is intended for residential application
and is not warranted for public or commercial use.
Please read carefully. Observing the following statements and warnings
reduces the likelihood of serious or fatal injury.
4
Periodic maintenance is required to ensure safe enjoyment
of your playset and optional accessories.
Observing the following procedures reduces the likelihood of serious or fatal injury.
PLAYSET CHECKLIST
At the beginning of each play season:
Twice a month during play season:
Once a month during play season:
MAINTENANCE
Activity on your playset and optional accessories may loosen fasteners. Check all lock nuts, hex and
lag bolts, quick clips, spring clips, acorn nuts, wood screws, and swing hangers for tightness and
tighten as required. T-nuts should be inspected for full and proper seating into the wood.
Checking, splitting and surface cracking are characteristics of all wooden playsets. This is caused by varying
seasonal temperatures and moisture conditions. To minimize this checking and/or cracking you may coat your
playset with a water repellent.
Tighten all hardware.
Lubricate all metallic moving parts per manufacturer’s instructions.
Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.
Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioration. Replace as needed.
Check metal parts for rust. If found, sand and repaint using a nonleaded-based paint meeting the requirements of 16 CFR 1303.
Check all wood members for deterioration and splinters. Sand down splinters and replace deteriorating wood members.
Reinstall any plastic parts, such as swing seats or any other items that were removed for the cold season.
Rake and check depth of loose ll protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.
Tighten all hardware.
Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.
Rake and check depth of loose ll protective surfacing materials to prevent compaction and to maintain appropriate depth. Replace as necessary.
Lubricate all metallic moving parts per manufacturer’s instructions.
Check all moving parts including swing seats, ropes, cables, and chains for wear, rust, or other deterioration. Replace as needed.
At the end of each play season or when the temperature drops below 10°F remove plastic swing seats, tents, sandbox cover, tire swing,
slide and other items as specied by the manufacturer and take indoors or do not use.
Rake and check depth of loose ll protective surfacing materials to prevent compaction and to maintain appropriate depth.Replace as necessary.
When you are ready to dispose of your playset, make sure that all metal, plastic and wood components are disposed of in
accordance with local waste ordinances.
Buyer and/or owner should disassemble and dispose of the playground equipment in such a way that no unreasonable hazards will
exist at the time the swing set is discarded.
5
PLAYGROUND SURFACING MATERIALS
SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME
PLAYGROUND SAFETY HANDBOOK9
Select Protective Surfacing
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under
and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with
ASTM Specication F 1292. There are different types of surfacing to choose from; whichever product you select, follow these guidelines:
NOTE: Do not install home playground equipment over concrete, asphalt, or any other hard surface. A fall onto a hard surface can result in
serious injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environmental factors can reduce
their shock absorbing effectiveness. Carpeting and thin mats are generally not adequate protective surfacing. Ground level equipment – such as
a sandbox, activity wall, playhouse or other equipment that has no elevated play surface – does not need any protective surfacing.
Loose-Fill Materials:
Maintain a minimum depth of 9 inches of loose- ll materials such as wood mulch/chips, engineered wood ber (EWF), or shredded/recycled
rubber mulch for equipment up to 8 feet high; and 9 inches of sand or pea gravel for equipment up to 5 feet high. NOTE: An initial ll level of
12 inches will compress to about a 9- inch depth of surfacing over time. The surfacing will also compact, displace, and settle, and should be
periodically relled to maintain at least a 9- inch depth.
Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be
adequate. (At depths less than 6 inches, the protective material is too easily displaced or compacted.)
Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to account for
water drainage. U.S Consumer Product Safety Commission, Washington, D.C., 20207 or call the toll-free hotline :1-800-638-2772
Check and maintain the depth of the loose-ll surfacing material. To maintain the right amount of loose-ll materials, mark the correct level on
play equipment support posts. That way you can easily see when to replenish and/or redistribute the surfacing.
Do not install loose ll surfacing over hard surfaces such as concrete or asphalt.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles:
You may be interested in using surfacing other than loose-ll materials – like rubber tiles or poured-in-place surfaces.
Installations of these surfaces generally require a professional and are not "do-it-yourself" projects.
Review surface specications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that the product
has been tested to the following safety standard: ASTM F 1292 Standard Specication for Impact Attenuation of Surfacing Materials within the
Use Zone of Playground Equipment. This report should show the specic height for which the surface is intended to protect against serious head
injury. This height should be equal to or greater than the fall height – vertical distance between a designated play surface (elevated surface for
standing, sitting, or climbing) and the protective surfacing below – of your play equipment.
Check the protective surfacing frequently for wear.
Placement
Proper placement and maintenance of protective surfacing is essential. Be sure to
Extend surfacing at least 6 feet from the equipment in all directions.
For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar from which
the swing is suspended.
For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all directions.
2H 2H
H
L
6 ft.
6 ft.
6 ft. 6 ft.
L+6 ft.
6 ft.
6 ft.
Use Zone for Single-Axis Swings Use Zone for Multi-Axis Swings
Denotes Use Zone with Protective Surfacing
Denotes Use Zone with Protective Surfacing
9 This information has been extracted from the CPSC publications "Playground Surfacing—Technical Information Guide" and "Handbook for Public
Playground Safety." Copies of these reports can be obtained by sending a postcard to the: Ofce of Public Affairs, U.S. Consumer Product Safety
Commission, Washington, D.C., 20207 or call the toll-free hotline: 1-800-638-2772
6
ORIENTATION
*Hint*
Throughout this manual references made to the Left Side,
the Right Side, the Front Side and the Back Side of the playset serve
as a consistent reminder to help with assembly.
PLAYSET
LEFT SIDE
FRONT SIDE
BACK SIDE
RIGHT SIDE
7
IMPORTANT!
A
A
B
B
Use these Assembly Procedure Hints throughout the installation process.
1. All Lag Bolts must have pre-drilled holes. Use a 1/4” drill bit for all 3/8” Lag Bolts.
Use a 3/16” drill bit for all 5/16” Lag Bolts. Pre-drilling pilot holes will help prevent Screws
and Lag Bolts from breaking and wood from splitting during assembly.
2. In areas where drilling a larger 1/2” hole is neccessary, such as when installing T- Nuts,
(Fig. 1) the recommended procedure is to first drill-through a 1/4” pilot hole from the
Hex Bolt side and then drill the larger 1/2” hole from the opposite T-Nut side. This will
help avoid splintering the wood. The “Drill Both Sides ICON” (Fig. 1) will remind you to
drill according to this procedure. Be sure to clean through-holes of debris before
inserting Hex Bolts.
3. When assembling parts that are difficult to hold in position while pre-drilling pilot holes
or assembling, use a clamp to keep parts aligned or in position. The “Clamp ICON”
(Fig. 2) will advise you to use this procedure.
Fig. 1 (example)
Fig. 2
Drill Both Sides
ICON
Clamp ICON
1/4” pilot hole
1/2” drill through
DO NOT OVER-TIGHTEN LAG BOLTS
8
WOOD PARTS LIST
x1
x1
WOOD PARTS
x2
x6
x1
x4
x1
x2
x16
x1
x1
x1
x1
3/4 x 5-3/8 x 23-3/4"
x2
x1
3/4 x 3 x 38-7/8"
1 x 3-3/8 x 45-1/8"
1-3/8 x 3-3/8 x 51"
1-3/8 x 3-3/8 x 47-3/4"
2899-CC
2502-CC
2521-CC
2522-CC
2966-CC
x4
x1 x1
1 x 3-1/2 x 15-3/8"
1-1/2 x 2-1/2 x 24" 1-3/8 x 3-3/8 x 17-1/4"
2524-CC
2490-CC PF 6295
2974-CC
2976-CC
2955-CC
2953-CC
x2
x1
2962-CC
1816-CC
2505-CC
2969-CC
2971-CC
2972-CC
2523-CC
2977-CC
3/4 x 3-3/8 x 27"
x1
2967-CC
x2
x2
2954-CC
2525-CC
3/4 x 3-3/8 x 28-5/8"
1-3/8 x 3-3/8 x 51"
3 x 3 x 45-1/8"1 x 5-1/2 x 45-1/8"
3/4 x 3-3/8 x 47"
1 x 3-3/8 x 47-1/8"
3/4 x 3-3/8 x 47-1/8"
5/8 x 3-1/4 x 29-3/4"
x1
3/4 x 3-3/8 x 17"
2965-CC
x2
3/4 x 5-3/8 x 23-3/4"
2960-CC
3/4 x 2-1/2 x 45"
x1
2516-CC
x7
2961-CC
3/4 x 5-1/2 x 44-7/8"
x1
2978-CC
1-3/8 x 3-3/8 x 18"
x4
2970-CC
1-3/8 x 3-3/8 x 51"
3 x 3 x 95"
3/4 x 3-3/8 x 53-7/8"
1 x 3-3/8 x 68-1/2"
3-3/8 x 5-3/8 x 95"
3 x 3 x 95"
3 x 3 x 95"
3/4 x 3-3/8 x 45-1/8"
x1
2968-CC
x2
3/4 x 3-3/8 x 12"
2975-CC
x2x6
x5
x2
1 x 3-3/8 x 40-1/2"3/4 x 5-3/8 x 23-3/4"
3/4 x 3-3/8 x 45-1/8"
1 x 3-3/8 x 37-1/8"
2963-CC2950-CC
2973-CC
2964-CC
9
ACCESSORIES
HARDWARE
Safety Handle
IN BAG
x2
x3
x6
x1
Rope Plaque
Trapeze
Swing
Climbing Rocks
x1
x4
Telescope Steering Wheel
x1
WS 4885 WS 4545
SA 4220 WS 4410
WS 4610 WS 4412
x6
Swing Hanger
2631-B
x1
WS 1501
x1
x1
x4
x1
x1
x2
x1
90
o
Angle Bracket Plate
L-Bracket
Swing Beam Flat Plate
Swing Beam Angled Plate Left Swing Beam Angled Plate RightSwing Beam 90
o
Plate
2411
2448
WS 4521
2447
2485
2412 2449
Anchor Stake
x1
SA 3097
x4
Safety Warning Plate
x1
SA 4294
10
PLAYSET FASTENERS
1"
3/8" T - NUT
5/16" T - NUT
3/8" FLAT WASHER
3/16" x 1" FENDER WASHER
3/8" LOCK WASHER
5/16" FLAT WASHER
5/16" LOCK
WASHER
1/4" LOCK
WASHER
TRUSS HEAD
SCREW
3/4"
3/8" LOCK NUT
2-1/2"
PAN HEAD
SCREW
2-1/2"
1-3/4"
PAN HEAD
SCREW
1-3/4"
3/8"
3/8"
3/8"
5/16"
5/16"
1/4"
1/4" ROCK WALL HARDWARE
T - Nut
Lock
Washer
Hex Bolt
Flat
Washer
1-1/2"
x19
x4
x20
x48
x28
x4
x10
x10
x4
x8
x12
x4
x4
11
PLAYSET FASTENERS
3/8"
LAG BOLT
WOOD SCREWS
4"
2-1/2"
3"
30 mm
2"
3/8"
5"
3/8"
2"
3/8"
3/8” HEX HEAD BOLTS
3-3/4"
1-1/4"
3/8"
1"
3/8"
3/8"
LAG BOLT
3"
x4
x4
x8
x2 x1
x12
x195
x95
x12
x1
x2
12
3/8" TORQUE
WASHER
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3/8"
3"
3-3/4"
4-1/2" 6-1/2"6" 8-1/2"
x5
x2 x6 x2 x2 x2 x1
1-1/2”
3/8”
BUTTON HD.
SCREW
1-1/2”
3/8”
BUTTON HD.
SCREW
1-1/2”
3/8”
BUTTON HD.
SCREW
1-1/2”
3/8”
BUTTON HD.
SCREW
x2
x2
3/8”
LAG BOLT
WOODSCREWS
4”
2-1/2”
3”
1-1/4”
1-5/8”
2”
3/8”
3/8”
2-1/2”
3/8”
2-1/4”
3/8”
2”
3/8”
3/8” HEX HEAD BOLTS
3-3/4”
1-1/2”
3/8”
1-1/4
”
3/8”
1-3/4”
3/8”
6”
3/8”
LAG BOLT
2-1/2”
3/8”
LAG BOLT
3”
5/16" 5/16"
13
CLUBHOUSE PARTS
CLUBHOUSE PARTS LIST
L-Bracket
x2
2412
3/4 x 3-3/8 x 19-1/4"
5/8 x 3-1/4 x 5"
5/16 x 2-15/16 x 16-13/16"
3/4 x 3 x 6-15/16"
3/4 x 3 x 10-5/16"
x4
x2
x2
x1
1806-CC
x1
1807-CC
1814-CC
1811-CC
2864-CC2852-CC
x2
2853-CC
x5
2855-CC
x8
1813-CC
x9
1808-CC
x2
1810-CC
x2
1809-CC
x2
PF-2990
x5
1826-CC
x1
5/8 x 1-7/8 x 12-7/16"
5/8 x 3/1/4 x 12-7/16"
5/8 x 3-1/4 x 14-3/4"
5/8 x 3-1/4 x 17"
5/8 x 3-1/4 x 9-1/2"
5/8 x 4-7/8 x 29-3/4"
3/4 x 3-3/8 x 45-1/8"
1 x 5-3/8 x 45-1/2"
1-3/8 x 3-3/8 x 51"
1812-CC
x2
Window
14
CLUBHOUSE FASTENERS
WOOD SCREWS
2-1/2"
2"
3/4"
1-3/16"
30 mm
1-1/2”
3/8”
BUTTON HD.
SCREW
1-1/2”
3/8”
BUTTON HD.
SCREW
1-1/2”
3/8”
BUTTON HD.
SCREW
1-1/2”
3/8”
BUTTON HD.
SCREW
x2
x2
3/8”
LAG BOLT
WOODSCREWS
4”
2-1/2”
3”
1-1/4”
1-5/8”
2”
3/8”
3/8”
3/8”
3/8”
3/8”
1-1/2”
3/8”
1-1/4
”
3/8”
3/8”
6”
3/8”
LAG BOLT
2-1/2”
3/8”
LAG BOLT
3”
5/16" 5/16"
5/16" T - NUT
5/16" FLAT WASHER
5/16" LOCK
WASHER
5/16"
5/16"
CLUBHOUSE HARDWARE
x4
x4
x4
x54
x100
x16 x20
15
PLAYSET SET-UP SAFETY AREA
29'- 4"
28'- 6"
6' SAFETY AREA
6' SAFETY AREA
6' SAFETY AREA
6' SAFETY AREA
16'- 6"
10'- 8"
HEIGHT
13'- 4"
13'- 4"
FRONT SIDE
BACK SIDE
LEFT SIDE
RIGHT SIDE
SWINGS
SLIDE
TERRACE
LADDER
ROCK
WALL
MONKEY BARS
(This space intentionally left blank.)
16
FORT BOTTOM FRAME BRACE
FLIP ASSEMBLY OVER TO INSTALL BOTTOM BRACE.
Flush
Flush
2-1/2"
Wood Screws
x6
x1
2969-CC
90°
FORT
CORNER POSTS
2-1/2" Wood Screw
Align braces with pre-drilled holes.
Ensure all bracing is square before
installing wood screws.
Hole for
Climbing Rope
BOTTOM
BOTTOM
T-Nut
x1
x1
2954-CC
2953-CC
3 x 3 x 95"
3 x 3 x 95"
x1
1 x 3-3/8 x 45-1/8"
x1
3/4 x 3-3/8 x 45-1/8"
2968-CC
2899-CC
x2
x2
3" Lag Bolt
Lock Washer
Flat Washer
3-3/4" Hex Bolt
Lock Washer
Flat Washer
90°
47-1/4"
79-1/4"
12-5/8"
1 x 5-1/2 x 45-1/8"
Flush
Flush
Flush
x2
x2
Note hole location.
2953-CC
17
FORT
FRAME BRACING
Align braces with
pre-drilled holes.
Flush
Flat Washer
x4
x1
1 x 3-3/8 x 45-1/8"
3/4 x 3-3/8 x 45-1/8"
x10
x2
Ensure all bracing is
square before installing
wood screws.
Flush
2899-CC
2973-CC
2-1/2"
Wood Screw
BOTTOM
x1
2969-CC
3/4 x 5-3/8 x 45-1/8"
x1
3/4 x 5-3/8 x 45-1/8"
2969-CC
FORT
FRAME BRACING
x2
Align braces with pre-drilled holes.
Flush
2-1/2" Wood Screw
Flush
Flush
Flush
3-3/4" Hex Bolt
Lock Washer
Flat Washer
x1
2953-CC
3 x 3 x 95"
x1
3/4 x 3-3/8 x 45-1/8"
2973-CC
x1
1 x 3-3/8 x 45-1/8"
2899-CC
Ensure all bracing is square before
installing wood screws.
90°
T-Nut
x2
x4
5" Hex Bolt
x4
x2
BOTTOM
47-1/4"
Lock Nut
Flat Washer
Note hole location.
Note hole location.
x1
2954-CC
3 x 3 x 95"
79-1/4"
18
FORT
BOTTOM FRAME BRACE
Align brace with pre-drilled holes.
FLIP ASSEMBLY OVER TO INSTALL BOTTOM BRACE.
Flush
Flush
2-1/2"
Wood
Screw
x1
2969-CC
3/4 x 5-3/8 x 45-1/8"
Ensure all bracing is square before
installing wood screws.
90°
x6
FORT
CONNECT FRAME SECTIONS
Align braces with pre-drilled holes.
Lock
Nut
Flat
Washer
ENSURE THESE
HOLES ARE ON
THIS SIDE.
x4
x2
x2
Flat Washer
5" Hex Bolt
2-1/2"
Wood Screw
x20
47-1/4"
47-1/4"
19
FORT
DECK CLEAT
Flush
Flush
EQUAL
EQUAL
EQUAL
EQUAL
3/4 x 2-1/2 x 45"
x1
2516-CC
2-1/2" Wood Screws
30 mm Wood Screws
(In center of planks)
x28
x14
FORT
DECK PLANKS
Flush
evenly spaced
x7
2961-CC
3/4 x 5-3/8 x 44-7/8"
Flush with
post.
To avoid splitting wood
pre-drill (2) 11/64" holes
2-1/2" Wood Screws
x4
3/8"
20
FORT
DECK PLANKS
30 mm Wood Screws
3/4 x 3 x 38-7/8"
x2
2962-CC
x8
x4
2-1/2" Wood Screws
FORT
DECK SUPPORT
Flush along
outer edge
Flush to
inside of 3x3
3" Wood Screws
x8
(3" screws into 3x3 posts)
(2" screws into deck frame)
Look for pre drills
2" Wood Screws
x8
1-3/8 x 3-3/8 x 18"
x4
2970-CC
2" Wood
Screws
3" Wood
Screws
Flush
2" Wood Screws
from inside
21
FORT
BALUSTER SUPPORTS
Flush at
all corners
Bottom rests ush
on lower brace
x6
x1
2-1/2" Wood Screws
2" Wood
Screw
RIGHT SIDE
FRONT SIDE
FORT
SWING BEAM SUPPORT
Small Holes UP
6" Carriage Bolt
Flat Washer
Lock Nut
Torque Washer
x2
x2
x1
2505-CC
3 x 3 x 45-1/8"
SET ON RAIL
Look for pre-drills
Flat Washer
Lock Nut
Torque Washer
6" Carriage Bolt
x1
3/4 x 3-3/8 x 45-1/8"
2973-CC
x1
3/4 x 3-3/8 x 19-1/4"
1814-CC
Note this
rope-hole
location
SWING BEAM
SUPPORT
Part 1814-CC is used in several applications.
Do not use the holes on the right side.
1814-CC
Pre-Drill 1/8" hole
3/8" up from lower
edge of 1814-CC.
3/8"
22
FORT
FORT
BALUSTER SUPPORT
UPPER BRACES
x1
2" Wood Screw
Flush
Flush
Flush
Bottom rests ush
on lower brace.
x2
2-1/2" Wood Screw
x8
2-1/2" Wood Screw
x2
3/4 x 3-3/8 x 45-1/8"
1812-CC
x1
3/4 x 3-3/8 x 19-1/4"
1814-CC
SWING BEAM
SUPPORT
Part 1814-CC is used in several applications.
Do not use the holes on the left side.
1814-CC
Note this
rope-hole
location
BACK SIDE
LEFT SIDE
Pre-Drill 1/8" hole 3/8"
up from lower edge of
1814-CC.
3/8"
23
FORT
Flush at
corners
Flush
AUX. FLOOR SUPPORT
x1
2973-CC
3/4 x 3-3/8 x 45-1/8"
FORT
ROOF SUPPORT
x2
3/4 x 3-3/8 x 53-7/8"
2976-CC
59-1/4"
2-1/2" Wood Screw
x4
2-1/2" Wood Screws
x12
4-3/8"
4-3/8"
LEFT SIDE FRONT SIDE
24
ROCK WALL ASSEMBLE
5-1/4"
23-3/4"
23-3/4"
2-1/2" Wood Screws
x4
Flush
Flush
5-1/4"
Outside
Dimension
Outside
Dimension
ROCK WALL ASSEMBLE
2-1/2"
Wood Screws
x28
HOLE
23-3/4"
3/4 x 5-3/8 x 23-3/4"
x1
2974-CC
3/4 x 5-3/8 x 23-3/4"
x5
2950-CC
Place planks onto rails (1826-CC) as shown.
If rails are fully pre-drilled, align all planks and screws with pre-drills.
If rails are not pre-drilled, install planks ush to each other.
Secure planks using 2-1/2" wood screws.
All Flush
Flush
Maintain Dimension
Rail (1826-CC) may have full or partiallly pre-drilled holes.
Align screws with the pre-drilled holes in rails (1826-CC).
3/4 x 5-3/8 x 23-3/4"
x1
2960-CC
1-3/8 x 3-3/8 x 51"
x2
1826-CC
3/4 x 5-3/8 x 23-3/4"
x1
2960-CC
25
ROCK WALL ROCKS
1/4" x 1-1/2" Hex Bolts
1/4" Lock Washers
T-Nuts
1/4" Flat Washers
x3 BAG
WS 4545
Do NOT attach top
board at this time.
ROCK WALL BRACKETS
5/16 x 1-1/2"
Button Head Screw
5/16" Lock Washer
5/16" Flat Washer
L-Bracket
5/16"
T-Nut
x2
x2
2412
x2
Install rocks at pre-drilled hole locations.
26
ROCK WALL INSTALL
Pre-drill two 1/4" pilot holes at marked locations.
Re-drill holes from opposite side using 3/8" bit.
SEE PAGE 7
FRONT SIDE
Rock Wall
ROCK WALL INSTALL
Mark (2) bracket holes.
3-3/4"
Mark
FRONT SIDE
27
ROCK WALL INSTALL
ROCK WALL INSTALL
2-1/2"
Wood
Screws
x2
5/16" x 1-1/4" Button
Head Screw
5/16" Lock Washer
5/16" Flat Washer
x2
BEGIN
HERE
x1
3/4 x 3-3/8 x 27"
2967-CC
2" Wood Screws
2-1/2" Wood Screws
x2
x2
5/16" T-Nut
x2
FRONT SIDE
Rock Wall
28
STEP LADDER
ASSEMBLE
ANGLE BRACE
INSTALL
Pre drill 3/16" pilot hole
2" deep for 4" lag bolt.
x1
1-3/8 x 3-3/8 x 47-3/4"
2966-CC
Flush
2-1/2" Wood
Screws
x4
Lock Washer
Flat Washer
x1
2966-CC
1-3/8 x 3-3/8 x 47-3/4"
3/4 x 5-3/8 x 23-3/4"
x1
2950-CC
3/4 x 3-3/8 x 28-5/8"
x1
2955-CC
3/4 x 3-3/8 x 28-5/8"
x1
2955-CC
3/4 x 3-3/8 x 28-5/8"
x1
2955-CC
2-1/2" Wood
Screws
2" Wood
Screws
x2
x2
2966-CC: Flush
angle to inner
corner of 3x3 post
Flush
Flush
BACK SIDE
4"
Lag Bolt
2-1/2" Wood Screws x16
Back side
of ladder
Before Assembling Step Ladder:
If 2521-CC has thru-hole, skip these steps.
1. Stack and align parts as shown with 2522-CC
on top.
2. Hold parts and drill 3/8" hole through 2521-CC
using 2522-CC as a guide.
3. Holes must be exactly aligned.
x4
1 x 3-1/2 x 15-3/8"
2524-CC
x1
1-3/8 x 3-3/8 x 51"
2521-CC
Flush to
front face.
1-3/8 x 3-3/8 x 51"
x1
2522-CC
Flush
Flush
29
ASSEMBLE
STEP LADDER
STEP LADDER
ASSEMBLE
5/16 x 1-1/2"
Button Head Screw
5/16" Lock Washer
5/16" L-Bracket
5/16" Flat Washer
5/16" T-Nut
x2
2-1/2" Wood screws
1/2" From Angle
x1
3/4 x 3-3/8 x 17"
2965-CC
x4
30
STEP LADDER
INSTALL
STEP LADDER
INSTALL
4-3/4"
Ladder Rail
Flush
Flush
Flush
Mark Bracket Hole
Locations.
Pre-drill two 1/4" pilot holes at marked locations.
Re-drill holes from opposite side using 3/8" bit.
SEE PAGE 7
BACK SIDE
BACK SIDE
31
STEP LADDER
INSTALL
STEP LADDER
INSTALL
BACK SIDE
Ladder
5/16" x 1-1/4"
Button Head Screw
5/16" Lock Washer
5/16" Flat Washer
x2
5/16" T-Nut
x2
32
SWING BEAM SWING HANGERS
Lock Nut
Cap
1-3/8"
Washer
2 Threads MIN.
Use a socket
wrench to tighten
Lock Nut securely
against washer.
Place Cap on threads
after tightening
Swing Hanger Bolt must protrude at least
TWO Threads beyond Lock Nut.
IMPORTANT!
Lock Nut
1-3/8" Washer
HOLD position of
Swing Hanger while
tightening Lock Nut.
Final position of each Spring Clip is
perpendicular to swing beam.
Swing Beam
IMPORTANT!
x1
3-3/8 x 5-3/ x 95"
2502-CC
SWING BEAM SWING HANGERS - INSTALL
You may need to tap with hammer to get though holes.
Swing Hanger Bolt
Flat Washer
Spring Clip
Swing Hanger
Swing Hanger
Swing Beam
Flat Washer
Final position of each Spring Clip is
perpendicular to swing beam.
IMPORTANT!
2631
x6
33
UPRIGHT INSTALL
EQUAL
EQUAL
Center 2977-CC. Mark and Pre drill 7/16" through holes for hex bolt.
x1
2977-CC
1 x 3-3/8 x 47"
SWING BEAM
SUPPORT
2505-CC
A - FRAME ASSEMBLE
T-Nut x2
30 mm Hex Bolt
Flush
x2
T-Nut
Flat Washer
Lock Washer
x2
3 x 3 x 95"
2525-CC
Rotate 2525-CC 180
o
after
installing T-Nuts.
34
FLAT PLATESWING BEAM
Flat Washer
Lock Nut
3" Carriage Bolt
x2
x2
2411
x1
A - FRAME ASSEMBLE
x1
1 x 3-3/8 x 68-1/2"
2978-CC
Pre-installed T-Nuts
are underneath.
2-1/2"
Wood Screws
x4
3-3/4" Hex Bolt
Lock Washer
Flat Washer
x2
35
A - FRAME
90
o
PLATE
3-3/4" Carriage Bolt
Lock Nut
Flat Washer
x2
2525-CC
2449
x1
SWING BEAM ANGLED PLATES
4-1/2" Carriage Bolt
Flat Washer
Lock Nut
x2
x2
x1
3-3/8 x 5-3/8 x 95"
2502-CC
2448
2447
x1
x1
DO NOT FULLY TIGHTEN
CARRIAGE BOLTS AT THIS TIME
NOTE: You may need to tap bolts with
hammer to get though holes.
Clean all debris from bolt threads
before installing lock nuts
36
3-3/4" Carriage Bolt
Flat Washer
Lock Nut
x4
x4
DO NOT FULLY TIGHTEN
CARRIAGE BOLTS AT THIS TIME
Align holes and insert carriage bolt.
Repeat where arrows are shown.
NOTE: You may need to tap bolts
with hammer to get though holes.
Clean all debris from bolt threads
before installing lock nuts
SWING BEAM ASSEMBLE
SWING BEAM ASSEMBLE
Position swing beam assembly resting upon A-frame.
37
Flat Washer
Lock Nut
6-1/2" Carriage Bolt
Torque Washer
You may need to tap with
hammer to get though holes.
SWING BEAM ASSEMBLE
Flat Washer
Lock Nut
6-1/2" Carriage Bolt
Torque Washer
x1
x1
x2
Position swing beam assembly resting upon
plate and align with holes.
2485
x1
NOTE: You may need to tap bolts
with hammer to get though holes.
Clean all debris from bolt threads
before installing lock nuts
SWING BEAM INSTALL
8-1/2" Carriage Bolt
x1
38
x1
x1
T-Nut
1" Hex Bolt
Lock Washer
Flat Washer
SWING BEAM INSTALL
2. Re-drill from opposite
side using 7/16" bit.
1. Pre-drill using 3/16" bit.
SEE PAGE 7
SWING BEAM
INSTALL
39
x2
2-1/2" Pan Head Screw
1/4" Lock Washer
SWING BEAM
ASSEMBLE
2977-CC
1"
1"
1"
1"
1"
1"
1"
1"
30 mm Wood Screws
x32
x8
2523-CC
5/8 x 3-1/4 x 29-3/4"
BALUSTERS
FORT
Install end-balusters rst,
1" from upright.
Flush
40
WINDOW
FORT
ROCK WALL SIDE BALUSTERS
FORT
3/4"
Wood Screws
x10
x1
2990
Place window centered
over opening and secure
using 3/4" screws.
OUTSIDE VIEW
VIEW
30 mm
Wood Screws
x16
x2
1811-CC
5/8 x 3-1/4 x 29-3/4"
x2
1810-CC
5/8 x 3-1/4 x 9-1/2"
x2
1809-CC
5/8 x 4-7/8 x 29-3/4"
Install end-baluster rst:
Flush tightly against
fort 3x3" corner post.
BEGIN
HERE
Flush
(ALL)
3x3"
INSIDE VIEW
VIEW
Flush
41
AT THIS TIME YOU WILL BUILD YOUR MONKEY BAR.
REFER TO THE MANUAL IN MONKEY BAR KIT FOR ASSEMBLY.
AFTER ASSEMBLY,
CONTINUE ON TO NEXT PAGE FOR INSTALLATION.
ACCESSORY NOTICE
STOP!
STOP!
42
MONKEY BAR
MONKEY BAR
INSTALL POSITION
INSTALL - STEP 1
* USE CARE WHEN INSTALLING
MONKEY BARS
* TWO PEOPLE AND A STEP LADDER ARE
RECOMMENDED FOR THIS STEP
SWING
BEAM
SIDE
TERRACE
SIDE
*Hint – Clamp Monkey Bar Assembly
in place while marking holes.
Flush at
TOP
Mark two drill-holes.
Ensure
inner side of
Top Ladder
Rail is ush
with inside
of 3x3 corner
post.
Flush
3x3
LADDER
43
MONKEY BAR
MONKEY BAR
INSTALL - STEP 2
INSTALL - STEP 3
Drill-Through 3/16" marked locations.
Re-Drill through using 7/16" bit from inside fort.
Flat Washer
LockWasher
T-Nut
1" Hex Bolt
x2
Flush at
TOP
Bolts must not protrude beyond T-Nut.
Add at washers as needed.
44
ANCHOR STAKES
INSTALL
Monkey Bar installation is
complete after installing
Anchor Stakes.
1/4 x 1-1/2"
Lag Bolts x2
Flat Washers x2
Metal Straps x2
x2
WS 4522
Install on Bottom Rail.
Instructions for anchoring your playset product to the ground.
1. Determine the nal location of your playset product.
2. Place the Anchor Stakes adjacent to the base and near
the corners of your playset product (at the bottom of
the legs on swing sets) and twist the auger-style Anchor
Stakes into the ground until only the loop is exposed.
3. Place the metal strap through the loop of the
Anchor Stake and secure it to the unit with a lag screw
and washer as shown.
Note: Attach the strap to the unit with as little play as
possible using whatever holes in the strap work the best.
45
LADDER SIDE BALUSTERS
LADDER SIDE BALUSTERS
FORT
FORT
INSTALLATION:
FROM INSIDE FORT
INSTALLATION:
FROM INSIDE FORT
VIEW
VIEW
30 mm
Wood Screws
x16
30 mm
Wood Screws
x36
x4
2523-CC
5/8 x 3-1/4 x 29-3/4"
x9
1813-CC
5/8 x 3-1/4 x 17"
13/16"
1" T Y P. 1" T Y P.
13/16" 13/16"
13/16"
INSIDE VIEW
3 x 3"
3 x 3"
INSIDE VIEW
BEGIN
HERE
BEGIN
HERE
Flush
Flush
MONKEY BAR WILL
NOT BE SHOWN FOR
BETTER CLARITY
DURING ASSEMBLY.
46
FORT
BAY WINDOW
FORT
BAY WINDOW
2" Wood Screws
x4
x1
1807-CC
3/4 x 3 x 10-5/16"
Flush
Flush
x1
1806-CC
3/4 x 3 x 6-15/16"
2-1/2" Wood Screws
x8
x2
1808-CC
1 x 5-3/8 x 45-1/8"
Flush
47
YOU WILL BUILD YOUR TERRACE AT THIS TIME.
GO TO NEXT PAGE.
TERRACE NOTICE
STOP!
STOP!
48
TERRACE PARTS
TERRACE PARTS LIST
5/8 x 3-1/4 x 29-3/4"
1 x 3-3/8 x 45-1/8”
5/8 x 3-1/4 x 27-1/2"
3/4 x 2-1/2 x 45-1/8"
5/8 x 3-3/8 x 45-1/8"
x10
x1
x10
x1
x3
2516-CC
1817-CC
2523-CC
1815-CC
2873-CC1816-CC
1818-CC
1820-CC
2879-CC
SP 2680
2660
1819-CC
1821-CC
PF 6295
SA 4211
1822-CC
1823-CC
x1
x2
x2
x2
x1
x1
x6
x5
x1
x2
x1
x2
5/8 x 5-3/8 x 38"
3/4 x 5-3/8 x 30-1/2"
3/4 x 3-3/8 x 45-1/2"
5/8 x 3-1/4 x 32-3/4"
SLIDE
FLAG
3/4 x 5-3/8 x 30-1/2"
3/4 x 3-3/8 x 33-1/2"
1-3/8 x 3-3/8 x 17"
3/4 x 5-1/2 x 45-1/8"
1-3/8 x 3-3/8 x 95"
3 x 3 x 45-1/8”
Green
Yellow
x1
1824-CC
49
FASTENERS
WOOD SCREWS
2-1/2"
1-3/16"
30 mm
2"
3/8"
3/8"
HEX BOLT
3/8"
HEX BOLT
1-3/4"
5"
3/8"
3/8” T - NUT
3/8” FLAT WASHER
3/8” LOCK WASHER
1"
1/4" x 1" FENDER WASHER
3/8" LOCK NUT
1-3/4"
PAN HEAD
SCREW
1-3/4"
3/8"
3/8”
3/8”
ACTUAL
SIZE
HARDWARE PARTS LIST
x2
x8
x2
x2
x3
x3
x115 x40 x70
x4
x2
50
BALUSTERS
INSTALL
FRAME
ASSEMBLE
Note hole locations (2)
BOTTOM
Flush
Flush
Flush
90°
90°
T-Nut
T-Nut
x2
1-3/4" Wood Screws
x24
Flush
Flush
Flush
Flush
Flush
62-3/4"
90-1/2"
27-1/2"
x2
3/4 x 3-3/8 x 45-1/8"
1820-CC
x2
5/8 x 3-3/8 x 45-1/8"
1817-CC
FLIP FRAME OVER TO
INSTALL BALUSTERS
Ensure Frame is square before
installing wood screws.
Space all Balusters 1/2" apart.
End balusters 5/8" from frame uprights.
Flush along bottom
BOTTOM
1/2" 1/2" 1/2" 1/2" 1/2"
1/2" 1/2" 1/2" 1/2"
5/8" 5/8"
30 mm Wood Screws
x40
x10
5/8 x 3-1/4 x 27-1/2"
2873-CC
Ensure Balusters are evenly spaced
installing wood screws.
x2
1-3/8 x 3-3/8 x 95"
1823-CC
51
SIDE RAILS
SIDE RAILS
INSTALL
INSTALL
90°
90°
90°
90°
90°
90°
59-1/4"
59-1/4"
27-1/2"
Ensure Side Rails are square
before installing wood screws.
Ensure Side Rails are square
before installing fasteners.
x5
3/4 x 3-3/8 x 33-1/2"
1821-CC
2-1/2" Wood Screws
x10
1-3/4" Wood Screws
x8
2" Hex Bolt
Lock Washer
Flat Washer
x2
Flush
Flush
Flush
Flush
Flush
Flush
Flush
x1
5/8 x 3-3/8 x 45-1/8"
1817-CC
x1
1 x 3-3/8 x 45-1/8"
1815-CC
Flush
Flush
Flush
Note hole
pattern
52
SLIDE SUPPORT
INSTALL
TERRACE
ASSEMBLE
Flush
LEFT
SIDE
RIGHT
SIDE
Approx.
28"
TILT FRAME UP
TO INSTALL TERRACE
Attach Terrace to
playset tower frame.
2-1/2" Wood Screws
x15
Flush
Flush
59-1/4" 59-1/4"
LEVEL
LEVEL
LEVEL
LEVEL
Flush
Flush
Flush
Ensure side rails are level
before installing wood
screws.
EQUAL
EQUAL
Center slide block (2490-ST)
between 3x3 posts
Flush
2490-CC
2-1/2" Wood Screws
x2
x1
1-1/2 x 2-1/2 x 24"
2490-CC
Pre-drill 1/8"
holes to avoid
splitting
53
DECK PLANKS
INSTALL
DECK SUPPORT & BAR TOP
INSTALL
30 mm Wood Screws
x8
30 mm Wood Screws
x4
End Screws: 2-1/2" (8)
End Screws: 2-1/2"
Middle Screws: 30 mm (4)
x2
3/4 x 5-3/8 x 30-1/2"
1818-CC
Ensure deck planks are ush
with side rails before installing
wood screws.
Top View
Flush with outer rails
1-3/4" Wood Screws
x6
Flush to top
of 2490-CC
slide block
Screws into baluster top rails.
x1
5/8 x 5-3/8 x 33"
1816-CC
x1
3/4 x 2-1/2 x 42-1/2"
1825-CC
Top View
15-3/4"
2-1/2" Wood Screws
x4
Pre-drill 1/8" holes
to avoid splitting
2-1/2" Wood Screws
x2
2490-CC
Pre-drill 1/8"
holes to avoid
splitting
54
TERRACE BALUSTERS
30 mm Wood Screws
x20
x5
5/8 x 3-1/4 x 29-3/4"
2523-CC
3"
3"
3"
3"
BACK
SIDE
DECK PLANKS
INSTALL
2-1/2" Wood Screws
x24
30 mm Wood Screws
x12
End Screws: 2-1/2" (24)
End Screws: 2-1/2"
Middle Screws: 30 mm (12)
x6
3/4 x 5-3/8 x 30-1/2"
1819-CC
Ensure equal spacing
of deck planks before
installing wood screws.
Top View
Equally spaced
Flush
Note hole
location.
Flush
55
TERRACE
BALUSTERS
TERRACE
ENTRY ARCH
30 mm
Wood
Screws
x24
Ensure balusters are
spaced evenly before
installing wood screws.
3-1/4"
LEFT
SIDE
EQUALEQUAL
Use a baluster as a spacer to
ensure correct baluster placement.
BEGIN MEASURING
AT CENTER SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
x6
5/8 x 3-1/4 x 29-3/4"
2523-CC
2-1/2" Wood Screws
x6
x1
3/4 x 5-1/2 x 45-1/8"
1822-CC
Flush
Flush
Install Entry Arch ush up against
bottom of playset roof rail.
Flush
56
FORT
SAFETY BARRIER
FORT
BALUSTER SUPPORTS
Flush
EQUAL
EQUAL
LEVEL
VIEW FROM UNDER
TERRACE
x1
2973-CC
3/4 x 3-3/8 x 45-1/8"
INSTALLATION:
UNDER TERRACE
2-1/2" Wood Screws
x4
Flush
Flush
2-1/2 Wood
Screws
x4
x2
2975-CC
3/4 x 3-3/8 x 12"
57
FORT
BALUSTERS
FORT
BAY WINDOW
30 mm
Wood Screws
x16
VIEW FROM INSIDE
FORT
INSTALLATION:
FROM INSIDE FORT
3x3"
3x3"
BEGIN
HERE
BEGIN
HERE
VIEW
Flush
Flush
Flush
x4
2523-CC
5/8 x 3-1/4 x 29-3/4"
2-1/2" 2-1/2"
30 mm Wood Screws
x16
x4
2853-CC
5/8 x 3-1/4 x 12-7/16"
Flush at top
Flush at top
Flush at corner.
Flush
BEGIN
HERE
58
FORT
BAY WINDOW
FORT
BAY WINDOW
30 mm Wood Screws
x8
EQUAL EQUAL
x1
2853-CC
5/8 x 3-1/4 x 12-7/16"
x2
FlushFlush Flush
Flush
2852-CC
5/8 x 1-7/8 x 12-7/16"
OUTSIDE VIEW
30 mm Wood Screws
x8
x4
2855-CC
5/8 x 3-1/4 x 12-7/16"
Flush Flush
Flush
OUTSIDE VIEW
59
FORT
BAY WINDOW
FORT
SWING BEAM SIDE WINDOWS
#8 x 3/4" Flat Head
Phillips Screws
x20
x2
PF2990
2855-CC
EQUAL
SIDE VIEW
EQUAL
EQUAL
EQUAL
OUTSIDE VIEW
30 mm Wood Screws
x16
x4
2855-CC
5/8 x 3-1/4 x 14-3/4"
x2
2864-CC
5/8 x 2-15/16 x 16-13/16"
2977-CC
1-11/16
1-11/16
Flush
INSTALLATION:
FROM INSIDE
FORT
INSIDE VIEW
60
FORT
SWING BEAM SIDE WINDOWS
ROOF FRAME
1-1/8"
OUTSIDE VIEW
#8 x 3/4" Flat Head
Phillips Screws
x20
x2
PF2990
EQUAL
SIDE VIEW
EQUAL
2855-CC PF2290
1-1/8"
VIEW
x2
2964-CC
1 x 3-3/8 x 37-1/8"
Flush
x2
2963-CC
1 x 3-3/8 x 40-1/2"
Orient 2963-CC so that pre-drilled holes at the top are horizontal.
If the holes are not horizontal, rotate the board.
Secure 2964-CC and 2963-CC using 3" screws.
T-Nut
x4
x4
2" Hex Bolt
Flat Washer
Lock Washer
Flush
Flush
Flush
Look for Pre-Drill
at end of 2963-CC
2964-CC
3" Wood Screw
x2
61
ROOF FRAME
Flush
3/4"
Pre-drill 1/8" x 1" deep for
screws to avoid splitting.
2-1/2" Wood Screws
x8
x1
2971-CC
1 x 3-3/8 x 47-1/8"
x1
2972-CC
3/4 x 3-3/8 x 47-1/8"
INSTALL THE WOOD ROOF ON YOUR PLAYSET AT THIS TIME.
REFER TO THE WOOD ROOF MANUAL FOR INSTALLATION.
ACCESSORIES NOTICE
STOP!
STOP!
Use pre-drills
62
SWINGS
INSTALL
8" Minimum when occupied.
Adjust chains at Top.
8"
53"
Adjust chains at Top
Attach Playset Plaque using one 1" philips head screw (provided) at each corner of plaque.
WS 4885
SWING
WS 4885
SWING
WS 1501
TRAPEZE
x1
SA 4220
63
TELESCOPE INSTALL
STEERING WHEEL INSTALL
1-1/2" Lag Bolt
Flat Washer
Steering Wheel Cap
DO NOT OVER-TIGHTEN LAG BOLT.
x1
WS 4412
Install WS 4412 inside fort.
Telescope and Bracket
Telescope
Bracket
Any Top Rail
Mounting Screw
x1
WS 4610
1. Position Mounting Bracket in desired location
(any Top Rail).
2. Attach Mounting Bracket to Top Rail using the
Mounting Screw provided.
3. Insert the Telescope into the Mounting Bracket
as shown.
64
FORT
Instructions for anchoring your playset product to the ground.
1. Determine the nal location of your playset product.
2. Place the Anchor Stakes adjacent to the base and near
the corners of your playset product (at the bottom of
the legs on swing sets) and twist the auger-style Anchor
Stakes into the ground until only the loop is exposed.
3. Place the metal strap through the loop of the
Anchor Stake and secure it to the unit with a lag screw
and washer as shown.
Note: Attach the strap to the unit with as little play as
possible using whatever holes in the strap work the best.
STAKES
TOWER UPRIGHT A FRAME
Install stakes into 3 x 3" uprights.
Locate stakes as shown.
Make sure all base pieces and uprights
are resting at on the ground.
It may be necessary to loosen the soil
beneath Playset to make everything level.
1-1/2" Lag Bolts
x2
Flat Washers
x2
Metal Anchor
Straps x2
x2
WS 4521
SWINGS
Flat Washers x2
1-1/2"
Lag Bolts x2
x2
WS 4521
Metal Anchor
Straps x2
65
CLIMBING ROPEACCESSORIES
Feed top of Climbing Rope through front of
Upper Rail (2968-CC) and tie a double knot
on the back side (Fig. 1).
For Safety, insure that the rope is
tight enough so that it can not be
looped back on itself.
Feed lower end of Climbing Rope through
hole in Rock Wall board (2974-CC) and tie a
double knot on the back side (Fig. 1).
Keep tying double knots at the
bottom end of rope until there is
no remaining loose rope.
Do not cut ends of rope.
Step 1
Step 2
Fig. 1
2968-CC
2974-CC
OPTIONAL:
Tie several single knots in
locations to allow logical
hand-grab points.
66
ACCESSORIES
ACCESSORIES
SAFETY HANDLES - STEP LADDER
SAFETY HANDLE - ROCK WALL
x3
WS 4410
1-1/2" Lag Bolt
Flat Washer
x6
DO NOT OVER-TIGHTEN LAG BOLTS.
Flat
Washer
1-1/2" Lag Bolt
DO NOT
OVER-TIGHTEN
LAG BOLTS!
x1
WS 4410
x2
67
FLAGS
ACCESSORIES
TUBE SLIDEACCESSORIES
IMPORTANT!
THE FOLLOWING STEPS ARE USED TO ASSEMBLE THE MOUNTING FRAME
FOR THE TUBE SLIDE.
THIS PROCEDURE SUPERCEDES THE FRAME MOUNTING INSTRUCTIONS
ORIGINALLY PACKAGED WITH THE TUBE SLIDE.
USE THE TUBE SLIDE INSTRUCTIONS TO ASSEMBLE THE TUBE SLIDE.
Locate ag base EQUALLY from top, bottom
and end of upper top rail (Fig. 1).
Attach each ag with 4 screws.
1
2
Fig. 1
3/4" Truss Head
Screws
x4
EQUAL
EQUAL
FRONT SIDE
STOP!
STOP!
68
PARTS LISTTUBE SLIDE
MOUNTING FRAMETUBE SLIDE
2" Wood Screws
3" Wood Screws
3/4 x 3-3/8 x 27-3/4"
1-1/4" Wood Screws
3/4 x 3-3/8 x 23"
3/4 x 5-3/8 x 23"
3/4 x 2 x 23"
1-3/4 x 3-3/8 x 33-1/2"
1-3/8 x 3 x 11-1/4"
3 x 3 x 18"
x45
x6
x10
Flush
Flush
2" Wood Screws
x3
3/4 x 3-3/8 x 27-3/4"
2888-CC
3/4 x 3-3/8 x 34-5/8"
x1
2893-CC
x1
2892-CC
x1
2891-CC
x2
2888-CC
x1
2887-CC
x1
2894-CC
x1
2890-CC
x2
2889-CC
69
MOUNTING FRAMETUBE SLIDE
MOUNTING FRAMETUBE SLIDE
1-1/4" Wood Screws
x10
1-1/4" Wood Screws
x10
3/4 x 3-3/8 x 23"
2887-CC
3/4 x 3-3/8 x 34-5/8"
2889-CC
3/4 x 3-3/8 x 34-5/8"
3/4 x 5-3/8 x 23"
2890-CC
2889-CC
70
MOUNTING FRAME
MOUNTING FRAME
TUBE SLIDE
TUBE SLIDE
1-1/4" Wood Screws
x12
3/4 x 3-3/8 x 27-3/4"
3/4 x 2 x 23"
2888-CC
NOTE:
Three screws from
FRONT SIDE
Deck Boards removed for clarity.
2891-CC
1-3/8 x 3-3/8 x 33-1/2"
2894-CC
3"
Wood
Screws
x5
28-3/4"
71
SLIDE SUPPORT TUBE SLIDE
3" Wood Screws
x2
1-3/8 x 3 x 11-1/4"
3 x 3 x 18"
2893-CC
2892-CC
NOTE:
Refer to the tube slide instruction
manual for steps to assemble
and attach the tube slide and tube
slide supports to the playset.
WARRANTY
WARRANTY REGISTRATION
Please complete your warranty registration to properly validate your warranty.
Register your product online at:www.OnlineWarranty.net.
Backyard Play Systems warrants the following:
1. All wood components have a Limited Five Year Warranty.
2. All non-wood components* have a three year Limited Warranty.
*Ropes carry a one year Limited Warranty.
3. Installation labor has a three year Limited Warranty applicable on playsets installed by Backyard Play
Systems. Labor warranty does NOT apply to Do-It-Yourself playset kits or kits installed by a third party.
Backyard Play Systems will repair, replace or pay for the affected part at our discretion. In no event shall
Backyard Play Systems pay the cost of labor or installation or any other costs related thereto.
Non-residential use of the system is prohibited and will void this warranty as the system is designed
for residential use only.
Conditions
The warranty is effective only when:
1. The unit has been erected in accordance with the assembly instructions.
2. The unit has been regularly and properly maintained and inspected.
3. The failure occurs when the unit is owned by the original purchaser.
4. This warranty is non-transferable
5. Backyard Play Systems has received a copy of your original proof of purchase with any claims in writing.
6. Backyard Play Systems has had reasonable opportunity during the sixty (60) days following the
receipt of notication to inspect and verify the failure prior to commencement of any repair work.
7. "Signicant color changes" to wood components is at the discretion of Backyard Products and
require proof in the form of photographs or inspection by Backyard Play Systems.
Wooden components may have imperfections such as checks and knots. These are natural
blemishes and imperfections which are inherent to wood. The imperfections not resulting in structural
failure are not covered under this warranty.
Requirements
To validate your warranty it is necessary to ll out and mail in the enclosed warranty card. And also to maintain
and inspect your playset regularly. Regularly is dened as once per start and end of season.
Claim Procedure
To make a claim under this warranty, you can either call 1-866-890-2211 or prepare a letter.
Please have ready the information below when you call or include the information in writing:
1. The model and size of the product.
2. A list of the part(s) for which the claim is made.
3. Proof of purchase of the Backyard Play Systems item, as shown on the original invoice.
4. Run Code, as listed on the enclosed warranty card.
Mail the above information to:
Backyard Play Systems
Attn: Customer Service
1000 Ternes Dr.
Monroe, MI 48162
Please feel free to call our Consumer Help Line Toll Free
1-866-890-2211
April through October M - F 8:00 AM to 6:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
No warranty is offered on the following: (1) equipment subject to abuse, negligence,
improper installation, vandalism, acts of God, unauthorized alteration or attachment to
equipment other than our own: or (2) equipment subjected to improper use, service or
repair by customer or any third party.
To the maximum extent permitted by law, this warranty and the remedies set forth
herein are exclusive and expressly in lieu of all other warranties, expressed or
implied, including warranties of merchantability or tness for a particular purpose.
If Backyard Play Systems cannot disclaim or exclude implied warranties under
applicable law, then to the extent possible any claims under any such implied
warranties shall expire on expiration of the applicable warranty period. Some
states do not allow limitations on how long an implied warranty lasts, so the above
limitation may or may not apply to you. Backyard Play Systems does not assume,
or authorize any person to assume for us, any other liability in connection with the
sale of our products.
To the maximum extent of the law, Backyard Play Systems assumes no
responsibility for incidental or consequential damages which may arise from
the purchase or use of our playset or equipment. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
If any provision of this limited warranty is invalid, void or unenforceable in any instance or
respect, the unenforceable provision will be severed and reformed to effect the intent of
this limited warranty to the maximum extent possible, and the remaining provisions shall
continue in full force and effect and shall be enforced to the full extent permitted by law.
This warranty gives you specic legal rights, and you may also have other rights which
vary from state to state.
WARRANTY TERMS MAY VARY OUTSIDE THE U.S.A.
This manual is your warranty certicate. Please retain your original proof of
purchase and this manual for any warranty claims.
WARRANTY
2695-RF
Call Us First!
DO NOT RETURN TO STORE.
For immediate help with assembly or product information
Call our toll-free number:
1-866-890-2211
April through October M - F 8:00 AM to 6:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
or email:
Our staff is ready to provide assistance.
- NOTICE -
This playset product is not intended for public use. It is intended for
residential application and is not warranted for public or commercial use.
IMPORTANT: THIS MANUAL SUPERSEDES THE MANUAL PACKED IN YOUR KIT.
USE IT TO ASSEMBLE YOUR MONKEY BARS!
NOTE: YOU MAY HAVE EXTRA FASTENERS AFTER FINISHING ASSEMBLY.
STOP!
STOP!
(This page intentionally left blank.)
- BEFORE YOU BEGIN -
- NOTICE -
This playset product is not intended for public use. It is intended for
residential application and is not warranted for public or commercial use.
10/24/20172695-RF
Monkey Bar Accessory
Backyard Play Systems
First...
Check with your homeowner’s association before
assembling.
Read instructions thoroughly before you begin. If you
have purchased accessories to accompany this
playset, please read all installation instructions before
beginning assembly of this structure.
Check All Parts
If a part is missing, circle the part in question and call.
Important
In a drawing, a dotted line represents a part hidden
from view (like a part under a panel).
Adult Assistance required
Assistance is necessary to handle,
t and secure some components.
Squareness is very Important!
Start with a level surface and keep 90° corners and 90°
perpendiculars throughout the assembly to ensure all
components t together.
Safety!
Check for protruding screws and bolts, verify all screw
and bolt lengths during assembly.
Always wear OSHA-APPROVED safety
glasses throughout assembly process.
Customer Service
1-866-890-2211
1000 Ternes
Monroe, MI 48162
Recommended for Ages 3 to 11
Your premium playset is manufactured from wood which has many natural characteristics and blemishes that may be present in some of the pieces in your playset. These natural characteristics may include knots or minor cracks/
splits. All individual parts have been cut to provide a smooth and safe surface. All parts have been inspected to assure we pack only the safest, most durable wood product. Any minor blemishes in your playset will not affect the
strength, durability, or structural integrity of the nished product. Our limited warranty does not cover the imperfections not resulting in structural failure.
Tools Required
Socket Set
Ratchet
Socket
Extension
Hammer
Phillips Bit
Combo Drive Bit
Cordless Drill
w/Charger
Drill Bits
Tape Measure
Level
C - Clamps
8’ Step Ladder
Model 34037
2
MONKEY BAR PARTS LIST
x2
x2
1-3/8 x 3-3/8 x 80-1/2"
x2
End Ladder Bottom Support
x1
1-3/8 x 3-3/8 x 78"
1-3/8 x 3-3/8 x 57"
x2
Anchor
2983-CC
2985-CC
2984-CC
2986-CC
WS 4522
Top Ladder Rail Support
End Ladder Angle Brace
1-3/8 x 3-3/8 x 81-1/16"
End Ladder Rail Support
3
1-1/2"
3/8
"
x2
3/8
"
HEX HEAD BOLTS
2-3/4"
3-1/4"
1"
3/8" T NUT
3/8" FLAT WASHER
3/8" LOCK WASHER
3/8" x 1-1/2"
BUTTON HD.
SCREW
x2
x2
3-3/4"
x2
x2
x18
x26
x18
4-3/4"
x2
1-1/2"
x6
ACTUAL SIZE
MONKEY BAR HARDWARE
- NOTICE -
Depending on your playset model, you will have extra hardware left over.
4
MONKEY BAR METAL PARTS
x2
Flat Metal Bracket
Top Rung End Rung
x5
18-1/2" 21-1/2"
x3
2023 PF 4972 PF 3297
FASTENERS FOR METAL RUNGS
x16
x16
1/4"
2-1/2"
Lock
Washer
Flat
Washer
x2
L-Bracket
Pan Head Screw
2084
Space intentionally left blank.
5
MONKEY BARS
TOP RAIL
2-1/2" Pan Head Screw
1/4" Lock Washer
x2
1-3/8 x 3-3/8 x 78"
2984-CC
x5
PF 4972
1" x 18-1/2"
PLAYSET ORIENTATION
LEFT SIDE
RIGHT SIDE
6' SAFETY AREA
6' SAFETY AREA
FRONT SIDE
BACK SIDE
REFER TO PLAYSET
INSTRUCTION MANUAL
FOR SAFETY AREA
x10
Flat side against wood.
Align with
pre-drilled holes
6
TOP RAIL / BRACKETS
ASSEMBLY
Leave Middle Hole OPEN
1-1/2" Hex Bolt (x4)
1-1/2" Hex Bolt (x2)
Flat Washer
Flat Washer
Lock Washer
Lock Washer
T-Nut (x8)
x2
1-3/8 x 3-3/8 x 78"
2984-CC
END RAIL ASSEMBLY
2-1/2" Pan Head Screw
1/4" Lock Washer
x3
PF 3297
1 x 21-1/2"
x2
1-3/8 x 3-3/8 x 81-1/16"
2986-CC
x2
2023
x6
Flat side against wood.
Align with
pre-drilled holes
7
END LADDER / TOP LADDER ASSEMBLY
1-1/2" Button
Head Screw
Flat Washer
Lock Washer
END RAIL
TOP RAIL
T-Nut
1-1/2" Button
Head Screw
Lock Washer
Flat Washer
Lock Washer
Flat Washer
3-1/4"
Hex Bolt
3-1/4"
Hex Bolt
Lock Washer
Flat Washer
T-Nut
8
ANGLE BRACES / BOTTOM SUPPORT
INSTALL
3-3/4"
Hex Head Bolt (x2)
Lock Washer
Flat Washer (x2)
T-Nut
T-Nut
Lock Washer
Flat Washer (x2)
T-Nut (x2)
2-1/2"
Hex Head Bolt (x2)
Lock Washer
Flat Washer
T-Nut
x2
1-3/8 x 3-3/8 x 57"
2983-CC
4-3/4"
Hex Head Bolt (x2)
x1
1-3/8 x 3-3/8 x 80-1/2"
2985-CC
NOTE:
Counter-bore of
2985-CC toward
rear side of ladder.
2-1/2"
Hex Head Bolt
9
MONKEY BAR
MONKEY BAR
INSTALL POSITION
INSTALL - STEP 1
* USE CARE WHEN INSTALLING
MONKEY BAR ASSEMBLY
* TWO PEOPLE AND A STEP LADDER ARE
RECOMMENDED FOR THIS STEP
SWING
BEAM
SIDE
SLIDE
SIDE
*Hint – Clamp Monkey Bar Assembly
in place while marking holes.
Flush at
TO P.
Mark two drill-holes.
10" FROM INSIDE OF
3x3 CORNER POST.
10"
10
MONKEY BAR
MONKEY BAR
INSTALL - STEP 2
INSTALL - STEP 3
Drill-Through 3/16" marked locations.
Re-Drill through using 7/16" bit from inside fort.
Flat
Washer
Lock
Washer
T-Nut
1" Hex Bolt
(x2)
Flush at
TOP
11
ANCHOR STAKES
INSTALL
1/4 x 1-1/2"
Lag Bolts x2
Flat Washers x2
Metal Straps x2
x2
WS 4522
Install on Bottom Rail.
Instructions for anchoring your playset product to the ground.
1. Determine the nal location of your playset product.
2. Place the Anchor Stakes adjacent to the base and near
the corners of your playset product (at the bottom of
the legs on swing sets) and twist the auger-style Anchor
Stakes into the ground until only the loop is exposed.
3. Place the metal strap through the loop of the
Anchor Stake and secure it to the unit with a lag screw
and washer as shown.
Note: Attach the strap to the unit with as little play as
possible using whatever holes in the strap work the best.
12
WARRANTY
Backyard Play Systems warrants the following:
1. All wood components have a Limited Five Year Warranty.
• Treated Wood - Backyard Play Systems will replace treated wood which becomes structurally unt
due solely to damage caused by fungal decay or termites.
2. All non-wood components* have a three year Limited Warranty.
*Ropes carry a one year Limited Warranty.
3. Installation labor has a one year Limited Warranty applicable on playsets installed by Backyard Play
Systems. Labor warranty does NOT apply to Do-It-Yourself playset kits or kits installed by a third party.
Backyard Play Systems will repair, replace or pay for the affected part at our discretion. In no event shall
Backyard Play Systems pay the cost of labor or installation or any other costs related thereto.
Non-residential use of the system is prohibited and will void this warranty as the system is designed
for residential use only.
Conditions
The warranty is effective only when:
1. The unit has been erected in accordance with the assembly instructions.
2. The unit has been regularly and properly maintained and inspected.
3. The failure occurs when the unit is owned by the original purchaser.
4. This warranty is non-transferable
5. Backyard Play Systems has received a copy of your original proof of purchase with any claims in writing.
6. Backyard Play Systems has had reasonable opportunity during the sixty (60) days following the
receipt of notication to inspect and verify the failure prior to commencement of any repair work.
7. “Signicant color changes” to wood components is at the discretion of Backyard Products and
require proof in the form of photographs or inspection by Backyard Play Systems.
Wooden components may have imperfections such as checks and knots. These are natural
blemishes and imperfections which are inherent to wood. The imperfections not resulting in structural
failure are not covered under this warranty.
Requirements
To validate your warranty it is necessary to ll out and mail in the enclosed warranty card. And also to maintain and
inspect your playset regularly. Regularly is dened as once per start and end of season.
Claim Procedure
To make a claim under this warranty, you can either call 1-866-890-2211 or prepare a letter.
Please have ready the information below when you call or include the information in writing:
1. The model and size of the product.
2. A list of the part(s) for which the claim is made.
3. Proof of purchase of the Backyard Play Systems item, as shown on the original invoice.
4. Run Code, as listed on the enclosed warranty card.
Mail the above information to:
Backyard Play Systems
Attn: Customer Service
1000 Ternes Dr.
Monroe, MI 48162
13
Please feel free to call our Consumer Help Line Toll Free
1-866-890-2211
April through October M - F 8:00 AM to 7:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
No warranty is offered on the following: (1) equipment subject to abuse, negligence,
improper installation, vandalism, acts of God, unauthorized alteration or attachment to
equipment other than our own: or (2) equipment subjected to improper use, service or
repair by customer or any third party.
To the maximum extent permitted by law, this warranty and the remedies set forth
herein are exclusive and expressly in lieu of all other warranties, expressed or
implied, including warranties of merchantability or tness for a particular purpose.
If Backyard Play Systems cannot disclaim or exclude implied warranties under
applicable law, then to the extent possible any claims under any such implied
warranties shall expire on expiration of the applicable warranty period. Some
states do not allow limitations on how long an implied warranty lasts, so the above
limitation may or may not apply to you. Backyard Play Systems does not assume,
or authorize any person to assume for us, any other liability in connection with the
sale of our products.
To the maximum extent of the law, Backyard Play Systems assumes no
responsibility for incidental or consequential damages which may arise from
the purchase or use of our playset or equipment. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
If any provision of this limited warranty is invalid, void or unenforceable in any instance or
respect, the unenforceable provision will be severed and reformed to effect the intent of
this limited warranty to the maximum extent possible, and the remaining provisions shall
continue in full force and effect and shall be enforced to the full extent permitted by law.
This warranty gives you specic legal rights, and you may also have other rights which
vary from state to state.
WARRANTY TERMS MAY VARY OUTSIDE THE U.S.A.
This manual is your warranty certicate. Please retain your original proof of
purchase and this manual for any warranty claims.
WARRANTY
2694-RF
Call Us First!
DO NOT RETURN TO STORE.
For immediate help with assembly or product information
Call our toll-free number:
1-800-890-2211
April through October M - F 8:00 AM to 6:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
or email:
Our staff is ready to provide assistance.
- NOTICE -
This playset product is not intended for public use. It is intended for
residential application and is not warranted for public or commercial use.
STOP!
STOP!
(This page intentionally left blank.)
- BEFORE YOU BEGIN -
- NOTICE -
This playset product is not intended for public use. It is intended for
residential application and is not warranted for public or commercial use.
01/29/20182694-RF
Cedar Roof Accessory
Backyard Play Systems
First...
Check with your homeowner’s association before
assembling.
Read instructions thoroughly before you begin. If you
have purchased accessories to accompany this
playset, please read all installation instructions before
beginning assembly of this structure.
Check All Parts
If a part is missing, circle the part in question and call.
Important
In a drawing, a dotted line represents a part hidden
from view (like a part under a panel).
Adult Assistance required
Assistance is necessary to handle,
t and secure some components.
Squareness is very Important!
Start with a level surface and keep 90° corners and 90°
perpendiculars throughout the assembly to ensure all
components t together.
Safety!
Check for protruding screws and bolts, verify all screw
and bolt lengths during assembly.
Always wear OSHA-APPROVED safety
glasses throughout assembly process.
Customer Service
1-866-890-2211
1000 Ternes
Monroe, MI 48162
Recommended for Ages 3 to 11
Your premium playset is manufactured from wood which has many natural characteristics and blemishes that may be present in some of the pieces in your playset. These natural characteristics may include knots or minor cracks/
splits. All individual parts have been cut to provide a smooth and safe surface. All parts have been inspected to assure we pack only the safest, most durable wood product. Any minor blemishes in your playset will not affect the
strength, durability, or structural integrity of the nished product. Our limited warranty does not cover the imperfections not resulting in structural failure.
Tools Required
Phillips Bit
Combo Drive Bit
Cordless Drill
w/Charger
Drill Bits
Tape Measure
Level
8’ Step Ladder
Model 4185,
4332, 4333,
4334, 4335,
6246, 6351,
6352, 6353,
6354, 6371
2
WOOD PARTS
SUB-ASSEMBLED DORMER PARTS
HARDWARE
Roof Slat Top
Roof Slat Mid
Roof Slat Bottom
Sun Decoration
Dormer Roof RIGHT
#8 Screw#8 Screw #8 Screw
Sun Brace
Dormer Roof LEFT
Sun Brace Center
Dormer Face
x2
x12
x2
5/8 x 5-1/8 x 51-1/8"
5/8 x 5-1/2 x 51-1/8"
5/8 x 5-1/8 x 51-1/8"
5/8 x 5-1/2 x 13-3/16"
2"30 mm 1-5/8"
2987-CC
2989-CC
2988-CC
x2
x1
2992-CC
3181-CC
x12
x1
x2
x1
x36 x74 x8
2990-CC
3180-CC
2991-CC
3182-CC
5/8 x 1-1/2 x 15-1/8"5/8 x 1-1/2 x 20-3/8"
3
ROOF FRAME INSTALL
Flush
3/4"
x1
2971-CC
1 x 3-3/8 x 47-1/8"
Pre-drill 1/8" x 1" deep for
screws to avoid splitting.
2-1/2" Wood Screws
x12
EQUAL
EQUAL
SUN DECORATION INSTALL
LEVEL
2500-CC
x2
5/8 x 5-1/2 x 13-3/16"
2992-CC
1-3/4"
Pre-drill 1/8" pilot holes.
x2
2972-CC
3/4 x 3-3/8 x 47-1/8"
30 mm Wood Screws
x2
4
Flush at top.
CENTER
Flush at top.
Install 2931-CC First.
SUN DECORATION
SUN DECORATION
INSTALL
INSTALL
x2
5/8 x 2 x 15-1/8"
2990-CC
x4
5/8 x 2 x 15-1/8"
2990-CC
Install 2991-CC centered and ush using two 30 mm screws as shown.
Install 2990-CC centered and ush using two 30 mm screws as shown.
Center remaining 2990-CC's as shown.
Measure and mark rafter as shown. Install two 2990-CC's between marks using two 30 mm screws.
Repeat installation of 2991-CC and 2990-CC at opposite side of playset.
2-1/2"
2-1/2"
13-1/2"
13-1/2"
CENTER
CENTER
CENTER
CENTER
30 mm Wood Screws
x6
30 mm Wood Screws
x8
x1
5/8 x 2 x 20-3/8"
2991-CC
ROOF PLANKS INSTALL
5
BEGIN HERE
1-5/8" Wood Screws
x8
5/8 x 5-1/8 x 51-1/8"
x2
2987-CC
ROOF PLANKS INSTALL
5/8 x 5-1/2 x 51-1/8"
x3
2989-CC
5/8 x 5-1/2 x 51-1/8"
x3
2989-CC
Install all roof
boards Flush.
Insert panels fully
seated.
Flush at
peak.
Center 2987-CC roof boards on rafters.
Ensure equal overhang on both sides; about 1".
47-1/8"
Maintain 47-1/8" dimension
between rafters.
1"
1"
1-5/8" Wood Screws
x24
DORMER ASSEMBLE
ROOF PLANKS INSTALL
6
BEGIN HERE
Align brace of 3181-CC ush with right frame of 3182-CC. Ensure ush at peak, all along edge and at corner.
Attach 3181-CC using #8 1-5/8" screws into middle of 3182-CC right frame.
x1
3181-CC
Flush
Flush
Flush along
inner edge.
Flush along
inner edge.
Pre-drill 1/8" holes
through 3182-CC.
1-5/8" Wood Screws
x3
x1
3182-CC
Flush
5/8 x 5-1/2 x 51-1/8"
x3
2989-CC
5/8 x 5-1/8 x 51-1/8"
x1
2988-CC
5/8 x 5-1/2 x 51-1/8"
x3
2989-CC
5/8 x 5-1/8 x 51-1/8"
x1
2988-CC
1-5/8" Wood Screws
x32
DORMER ASSEMBLE
DORMER INSTALL
7
STOP
Align bottom of
dormer frame with top
of 2nd roof plank.
(Fig. 1)
Align brace of 3180-CC ush with left frame of 3182-CC. Ensure ush at peak, all along edge and at corner.
Attach 3180-CC using #8 1-5/8" screws into middle of 3182-CC left frame.
Attach assembled dormer using #8 2" screws into roof planks as shown.
x1
3180-CC
Flush
Flush along
inner edge.
Pre-drill 1/8" holes
through 3180-CC.
2" Wood Screws
x6
1-5/8" Wood Screws
x3
x1
3182-CC
Flush
Flush
RETURN TO PLAYSET INSTRUCTION MANUAL
ROCK WALL SIDE
Install screws through dormer roof frame (Fig. 1).
25-1/2"
25-1/2"
Pre-drill 1/8"
holes.
8
9
WARRANTY
Backyard Play Systems warrants the following:
1. All wood components have a Limited Five Year Warranty.
• Treated Wood - Backyard Play Systems will replace treated wood which becomes structurally unt
due solely to damage caused by fungal decay or termites.
2. All non-wood components* have a three year Limited Warranty.
*Ropes carry a one year Limited Warranty.
3. Installation labor has a one year Limited Warranty applicable on playsets installed by Backyard Play
Systems. Labor warranty does NOT apply to Do-It-Yourself playset kits or kits installed by a third party.
Backyard Play Systems will repair, replace or pay for the affected part at our discretion. In no event shall
Backyard Play Systems pay the cost of labor or installation or any other costs related thereto.
Non-residential use of the system is prohibited and will void this warranty as the system is designed
for residential use only.
Conditions
The warranty is effective only when:
1. The unit has been erected in accordance with the assembly instructions.
2. The unit has been regularly and properly maintained and inspected.
3. The failure occurs when the unit is owned by the original purchaser.
4. This warranty is non-transferable
5. Backyard Play Systems has received a copy of your original proof of purchase with any claims in writing.
6. Backyard Play Systems has had reasonable opportunity during the sixty (60) days following the
receipt of notication to inspect and verify the failure prior to commencement of any repair work.
7. “Signicant color changes” to wood components is at the discretion of Backyard Products and
require proof in the form of photographs or inspection by Backyard Play Systems.
Wooden components may have imperfections such as checks and knots. These are natural
blemishes and imperfections which are inherent to wood. The imperfections not resulting in structural
failure are not covered under this warranty.
Requirements
To validate your warranty it is necessary to ll out and mail in the enclosed warranty card. And also to maintain and
inspect your playset regularly. Regularly is dened as once per start and end of season.
Claim Procedure
To make a claim under this warranty, you can either call 1-866-890-2211 or prepare a letter.
Please have ready the information below when you call or include the information in writing:
1. The model and size of the product.
2. A list of the part(s) for which the claim is made.
3. Proof of purchase of the Backyard Play Systems item, as shown on the original invoice.
4. Run Code, as listed on the enclosed warranty card.
Mail the above information to:
Backyard Play Systems
Attn: Customer Service
1000 Ternes Dr.
Monroe, MI 48162
10
Please feel free to call our Consumer Help Line Toll Free
1-866-890-2211
April through October M - F 8:00 AM to 7:00 PM EST
Saturday 8:30 AM to 4:30 PM EST
November through March M - F 8:00 AM to 5:00 PM EST
No warranty is offered on the following: (1) equipment subject to abuse, negligence,
improper installation, vandalism, acts of God, unauthorized alteration or attachment to
equipment other than our own: or (2) equipment subjected to improper use, service or
repair by customer or any third party.
To the maximum extent permitted by law, this warranty and the remedies set forth
herein are exclusive and expressly in lieu of all other warranties, expressed or
implied, including warranties of merchantability or tness for a particular purpose.
If Backyard Play Systems cannot disclaim or exclude implied warranties under
applicable law, then to the extent possible any claims under any such implied
warranties shall expire on expiration of the applicable warranty period. Some
states do not allow limitations on how long an implied warranty lasts, so the above
limitation may or may not apply to you. Backyard Play Systems does not assume,
or authorize any person to assume for us, any other liability in connection with the
sale of our products.
To the maximum extent of the law, Backyard Play Systems assumes no
responsibility for incidental or consequential damages which may arise from
the purchase or use of our playset or equipment. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
If any provision of this limited warranty is invalid, void or unenforceable in any instance or
respect, the unenforceable provision will be severed and reformed to effect the intent of
this limited warranty to the maximum extent possible, and the remaining provisions shall
continue in full force and effect and shall be enforced to the full extent permitted by law.
This warranty gives you specic legal rights, and you may also have other rights which
vary from state to state.
WARRANTY TERMS MAY VARY OUTSIDE THE U.S.A.
This manual is your warranty certicate. Please retain your original proof of
purchase and this manual for any warranty claims.
WARRANTY
Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545
Visit our web site at: www.swing-n-slide.com or call us at
(("!-#()'*)$#(
)=@357AB3@G=C@>@=2C1B/<22=E<:=/2C<7BA>317471)C@0=)C03(:7237<AB@C1B7=<A
D7A7B
6BB>EEEAE7<5<A:7231=;
Other benefits include information on product warranties, assembly plan updates, joining our mailing
list for new products and promotions, and providing feedback on products.
"%$')#)
PLEASE READ BEFORE BEGINNING ASSEMBLY!!
Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing
anything, please
$#$)')*'#
to the store where purchased. Please call our Customer
Service Department at the number below.
#=B3This accessory is designed to fit a Z31963756B=<:G.
* ) $ #
•
Do not climb on the
outside of the slide
• This slide is designed for
home use only, not for
Public Playgrounds
• Product intended for
children ages from 2-10
years old.
5' Turbo Tube Slide
!
WARNING:
Assembly by an adult.
2
"
7
<7
;C;
(/43BG.=<3
)C@0=)C03(:723
7;3<A7=<A
3
(:
7
2
3(/43BG
.
=
<
3
(E7<53/;
(/43BG.=<3
(E7<53/;
(/43BG.=<3
(E7<53/;
(:723(/43BG
.=<3
%@=>3@%:/13;3<B=4)C@0=)C03(:723=<
)63)=E3@
(:723(/43B
G
.=<3
$>B7=<
$>B7=<
$>B7=<
#$)
This diagram is based
on a 47-1/2’’ square
deck.
-(
-(
#$
4
Installation Safety – Have You:
Consulted the assembly instructions supplied with your particular model?
Noted this accessory is to be used only on Swing•N•Slide approved designs? (Do not alter its design or add/remove components.)
Made sure all hardware is tightened securely? (Supplied bolt covers must also be fastened securely.)
Using a hacksaw, cut off all protruding threaded ends of bolts and other fasteners and remove any sharp edges with
a metal file as needed, and coated fastener ends with lead free paint?
Placed the equipment on level ground, not less than six feet (1.8 meters) from any structure or obstruction such as a fence, garage,
house, overhanging branches, laundry lines, or electrical wires?
Made sure home playground equipment is not installed over concrete, asphalt, packed earth or any other hard surface? (A fall onto
a hard surface can result in serious injury to the equipment user.)
Verified that suspended climbing ropes, chain,or cable are securely anchored at both ends and cannot be looped back unpon itself?
Consulted in assembly instructions of your particular model for minimum use zones?
Used a water sealant on your play set to protect the wood and prevent cracking and warping?
Followed all anchoring and shock absorbing surfacing requirements on the back of this sheet as they apply?
Made sure not to allow children to use equipment until it is properly installed?
Made sure to adjust all swings so there is a minimum 8'' clearance between the swing and the ground surface?
Operating Safety – Have You:
Determined that on-site adult supervision is provided for children of all ages?
Warned children the following before allowing them to use the equipment?
Not to walk close to, in front of, behind or between moving items.
Not to twist swing or any other accessory chains or ropes or loop them over the top support bar since this will reduce the
strength of chain or rope.
Not to swing empty seats or other accessories.
Not to slide down swing chains.
Be sure to sit in the center of the swing seat and other accessories with full weight on the seat.
Not to attach items to the playground equipment that are not specifically designed for use with the equipment such as but not
limited to, jump ropes, clotheslines, pet leashes, cables and chain. They may cause a strangulation hazard.
Not to climb or walk on the top of swing beams, railings or roof.
Not to use equipment in a manner other than intended.
Not to get off equipment while it is in motion.
Not to climb on the equipment when it is wet.
Be sure to go down slides feet first.
Determined that only one child per planned occupant seat should be allowed on this set at one time.
Determined children must be dressed appropriately for play. Avoid hooded jackets, bicycle or other sports helmets, clothing with
draw strings and loose fitting clothes which could become entangled or snagged on equipment.
Determined that suspended climbing ropes, chain, or cable are securely anchored at both ends and cannot be looped back upon
itself.
Made certain the slide is placed so that is is not in direct sunlight.
Safety Maintenance – Follow these preventive maintenance instructions at the intervals required:
To prevent the deterioration of materials, remove plastic swing seats and other plastic accessories when outdoors temp dips down to
or below 32° F and take indoors. Reinstall these plastic elements at the beginning of each play season.
At the beginning of each play season check metal parts for rust. If found, sand and repaint using a non lead-based paint meeting the
requirements of 16 CFR 1303 or SOR/2005-109.
At the beginning of each play season and once a month during each play season, check all moving parts for wear, rust or other
deterioration. Replace as needed. If any of these conditions exist, call 1-800-888-1232 to order replacement accessories.
At the beginning of each play season and once a month during each play season lubricate metallic moving parts.
At the beginning of each play season and twice a month during each play season, check all protective coverings on bolts, pipes,
edges, and corners. Replace if they are loose, cracked, or missing.
At the beginning of each play season and twice a month during each play season, rake and check depth of loose fill protective
surfacing material to prevent compaction and maintain appropriate depth. Replace as necessary.
At the beginning of each play season and twice a month during each play season tighten all hardware.
At the beginning of each play season and twice a month during each play season, check all wood members for deterioration and
splinters. Sand down splinters and replace deteriorating wood members.
Disposal Instructions
When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at
the time the set is discarded.
Important!
Additional Safety Instructions for all Swing-N-Slide Playground Equipment.
Save this instruction sheet in the event the manufacturer needs to be contacted.
Observing the following statements and warnings reduces the likelihood of serious or fatal injury
Safety Checklist for Swing-N-Slide Play Sets and Accessories
5
This product is intended for single family home/residential use only and not intended for use in any public setting.
Placement in any public setting constitutes a misuse of this product.
IMPORTANT!
ADDITIONAL REQUIRED SAFETY INSTALLATION INSTRUCTIONS
According to ASTM requirements, all kits must be anchored to the ground and, if the unit has a climbing rope, the rope end must be anchored to the ground. If soil conditions
permit stakes to be pulled out easily, cementing into ground is necessary.
•
To anchor the unit to the ground, Follow the instructions included in this plan for applying Anchor-It devices to your unit, or use 2" x 4" x 18" (45mm x 95mm x 457mm) pressure-
t
reated stakes. Pound stakes into ground at least 12" (305mm) at all inside corners of the posts (including A-frame legs and climbing unit posts). Attach with four (4) 16D (3-1/2")
g
alvanized nails per stake into each tower and/or A-frame upright.
•
If the unit has a climbing rope, securely anchor the rope at both ends.
• Once the unit is completely assembled and before children are allowed to play on it, proper shock-absorbing surfacing material must be installed. This may be accomplished by
using loose-fill materials at a sufficient depth. The Consumer Product Safety Commission “Handbook for Public Playground Safety” lists the following materials and required
depths that are sufficient for home/residential application. Supplemental information may be found in ASTM F1292. For fall height protection up to 9 ft. (2.742m) [recommended
for Swing•N•Slide kits]:
LOOSE FILL MATERIAL REQUIRED (UNCOMPRESSED) DEPTH
1
in. (mm)
Wood Mulch 9" (229mm)
Double Shredded Bark Mulch 9" (229mm)
Uniform Wood Chips 12" (305mm)
These depths were derived from the CPSC Handbook. Swing•N•Slide has not done independent tests to determine these required depths.
When properly installed, shock absorbing material will completely cover the horizontal baseboards on climbing units. This protective surfacing must extend a minimum of 6 ft.
(1.828m) in all directions from the perimeter of the equipment or from the outermost edges of any component. For example, a slide extending beyond the platform must have
protective surfacing at least 6 ft. (1.828mm) out from both sides as well as the end. For swings, the protective surface must extend at least 14 ft. (6m)
out from both the back and
front of the swing when the swing is in its rest position.
Swing-N-Slide® MANUFACTURERS LIMITED WARRANTY
Swing-N-Slide® takes great pride in the quality and durability of our products. Our Manufacturer’s Limited Warranty provides confidence and demonstrates our commitment
to providing quality residential playground products.
MANUFACTURER’S LIFETIME LIMITED WARRANTY
Swing-N-Slide® warrants its thermoformed slides and climbing mountains to be free from defects in workmanship and materials, under normal use and conditions, for the
lifetime of the product.
MANUFACTURER’S 5 YEAR LIMITED WARRANTY
Swing-N-Slide® warrants its Custom Ready-to-Build Play Set kits and accessories to be free from defects in workmanship and materials, under normal use and conditions,
for a period of 5 years.
MANUFACTURER’S 5 YEAR LIMITED WARRANTY
Swing-N-Slide® warrants its No-Cut and Wood Complete Ready-to-Assemble Play Set kits against wood rot and termite damage, and to be free from defects in
workmanship and materials, under normal use and conditions, for a period of 5 years for structural wood components.
Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or
any other physical properties of wood that do not present a safety hazard, are not covered by this warranty.
MANUFACTURER’S ONE YEAR WARRANTY
Swing-N-Slide® warrants its canopy roofs and/or tarps, and Timber GLOVE lumber wrap to be free from defects in workmanship and materials, under normal use and
conditions, for a period of one year.
Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials. This decision is subject
to verification of the defect upon delivery of the defective part to Swing-N-Slide® at 1212 Barberry Drive, Janesville, Wisconsin, 53545. Any part(s) returned to Swing-N-
Slide® must have prior approved Return Authorization Number and proof of purchase, including the date of purchase. This warranty is valid only if the product is used for
the purpose for which it was designed and installed at a residential, single family dwelling. This warranty is void if the product is put to commercial or institutional use. This
warranty does not cover (a) products which have been damaged by acts of Nature, negligence, misuse, or accident, or which have been modified or repaired by
unauthorized persons; (b) the cost of labor; or the cost of shipping the product, any part, or any replacement product or part.
Swing-N-Slide® DISCLAIMS ALL OTHER REPRESENTATIONS AND WARRANTIES OF ANY KIND, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. Swing-N-Slide® WILL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. This warranty is non-transferable and does not extend to the owners of the product subsequent to the original purchaser. Some states do not
allow limitations on implied warranties or exclusion of incidental or consequential damages, so these restrictions may not be applicable to you. This warranty gives you
specific legal rights. You may also have other rights, which vary from state to state.
This warranty also does not apply to:
• Structures not erected, maintained or inspected in conformance with Swing-N-Slide® installation plans
• Structures that have had parts added or substituted not in conformance with Swing-N-Slide® installation plans
• Parts that have been modified, altered or misused
• Parts that have not been used as designed or intended
• Damage due to acts of Nature, vandalism, abnormal use or abuse as determined by Swing-N-Slide®
=@4C@B63@7<4=@;/B7=<=<>:/G5@=C<2A/43BG
the Consumer Product Safety Commission
(CPSC) publishes the Outdoor Home Playground Safety Handbook which can be downloaded for free
from EEE1>A15=D. An additional resource is the American Society of Testing and Materials (ASTM)
Standard Consumer Safety Performance Specification for Home Playground Equipment (ASTM F1148)
which can be purchased and downloaded from EEE/AB;=@5.
6
Assembly Instructions
TOOLS REQUIRED
(1) 2'' x 4'' x 96''
25''
25''
23'' 23''
(1) 2'' x 4'' x 96''
18'' 18'' 18''
11-1/4''
8-1/4'' 8-1/4''
(2) 2'' x 4'' x 96''
LUMBER REQUIRED: (4) 2'' x 4'' x 96''
(
&*'
'*!'(,
'!!
)%"(*'
()-!(((
*()"(
($ ),'#
5/16'' Flat Washers
5/16'' loc nuts
5/16'' x 3/4" Hex
Head Bolts
2-1/2" Wood Screw
2" Wood Screw
2" Lag Screw
','#!*
1-1/4'' Lag Screw
T30 Torx® Bit
T20 Torx® Bit
!*"'*)!()
)$#!!*"'%*'((%')!-
,'#
7
Assembly Instructions
Entrance Piece LH
Entrance Piece RH
Elbow
Exit Elbow
Exit
Elbow Support
Bracket
Entrance Bracket
(!$"%$##)(
T-Bar Support Bracket
8
Assembly Instructions
75
ENTRANCE SECTION ASSEMBLY
NOTES:
• At least two individuals are needed to assemble the 5' Turbo Tube Slide.
• To aid in aligning holes when assembling sections, insert a screwdriver through adjacent holes to maintain hole
alignment.
1. Assemble the Entrance Section by securing the top seam first, as shown in (Fig. 1) and (Fig. 1a). Join sections using a
hex head bolt, two flat washers, and a loc nut at each hole junction.
2. When securing the bottom seam make certain to attach the Entrance Bracket to the left side of the seam as shown in
(Fig. 1) securing in place as shown in (Fig. 1a).
3. Tighten all hardware.
Hex Head Bolt
Washer
Washer
Loc Nut
Entrance Section - 8 bolts
Entrance Bracket
75/
9
Assembly Instructions
Washer
Washer
Loc Nut
75/
75
750
Elbow Support
Bracket
Exit Section - 9 bolts
Elbow Section - 9 bolts each
F
ELBOW AND EXIT SECTION ASSEMBLY
1. Assemble the Elbow Section by securing as shown in
(Fig. 2) and (Fig. 2a). Join sections using a hex head
bolt, two flat washers, and a loc nut at each hole
junction.
NOTE: Fasten each loc nut finger tight. Each time you
join parts be sure each flanged lip is mating with a flat
lip.
2. Repeat step 1 to assemble (3) remaining Elbow Sections.
3. Assemble and secure the Exit Section as shown in
(Fig. 2a) and (Fig. 2b). Make certain to attach the
Elbow Support Bracket to the bottom of the flange,
as shown in (Fig. 2b).
4. Tighten all hardware.
NOTE: Interlocking design of flanges on Elbow pieces
will assist in assembly.
!#)!
:/<53$>3<7<5
Hex Head Bolt
10
Assembly Instructions
Slide Elbows
1. Align the first elbow section to the Entrance
Section with the seams aligned and the exit facing
downward. Rotate the Elbow (2) holes to the right
as shown in (Fig. 3) and secure in place. Look
for the Flange Opening shown in (Fig. 3a).
2. Align second elbow so that Hole #1 aligns with
the flange opening as shown in (Fig. 3c) and
(Fig. 3d) and secure in place.
NOTE: Interlocking design of flanges on Elbow
pieces will assist in assembly.
NOTE: Hand tighten the loc nuts only.
Elbow Section - 12 bolts
Elbow Section - 12 bolts
!#)!
Washer
Washer
Loc Nut
751
Hole #1
:/<53$>3<7<5
75
:/<53$>3<7<5
75/
752
750
Hex Head Bolt
11
Assembly Instructions
Washer
Washer
Loc Nut
75/
Slide Elbows
1. Align third elbow so that Hole #1 aligns with the
flange opening as shown in (Fig. 4) and
(Fig. 4c) and secure in place.
2. Align fourth elbow so that Hole #1 aligns with the
flange opening, as shown in (Fig. 4b) and
(Fig. 4c) and secure in place.
NOTE: Interlocking design of flanges on Elbow
pieces will assist in assembly.
NOTE: Hand tighten the loc nuts only.
Elbow Section - 12 bolts
75
750
Flange Opening
Hole #1
751
Elbow Section - 12 bolts
Hex Head Bolt
12
Assembly Instructions
Washer
Washer
Loc Nut
75/
Slide Exit
1. Align Exit Elbow Section so that Hole #1 aligns
with the opening in the flange, as shown in
(Fig. 5) and (Fig. 5b) and secure in place.
2. Attach the Exit to the Exit Elbow Section so that
the top of the exit matches the seams, as shown in
(Fig. 5c) and secure in place.
3. Tighten all hardware.
NOTE: Interlocking design of flanges on Elbow
pieces will assist in assembly.
Exit Elbow Section - 12 bolts
Exit - 6 bolts
75
Flange Opening
Hole #1
750
751
Align Top Edge of
Slide Base with Exit
Section Seam.
Hex Head Bolt
13
Assembly Instructions
75
Slide Barrier Construction
1. Carefully remove your Barrier Support Boards
from the barrier where you would like to place
your slide, making certain you will have a clear
72'' Safety Zone for your slide. (Fig. 6).
Retain this lumber and fasteners as you will need
them in a later step.
2. Cut to length and install (2) 2'' x 4'' Barrier
Support Boards as shown in (Fig. 6a), making
certain the opening between them is 25''.
3. Cut (1) 2'' x 4'' Barrier Board to the height of
your barrier railing and create a slide opening of
23'', as shown in (Fig. 6a).
4. Reattach your barrier boards, making certain
they are evenly spaced and do not have a gap
larger than 3'' between each board, as shown in
(Fig. 6a).
75/
2'
'
x 4'
'
Cut T
o Width of Y
our
Unit
2-1/2''
screws
per joint
25''
23''
3-1/4'' Gap
Between Each
Barrier Board
2
''
x
4
''
Cut To Wid
th
o
f Yo
u
r Un
it
#$)
)67A>:/<CA3A/53<3@71B=E3@B=
7::CAB@/B3B63)C@0=)C03(:723037<5
/BB/1632=E3D3@B67AA/;3>@=132C@3
7AB=03CA324=@/<G(E7<5#(:723
Z)=E3@%:/GA3B
5' DECK HEIGHT
2'' x 4''
Barrier Board
Cut to Height
of Rail
2-1/2''
screws
per barrier
board
14
Assembly Instructions
2'' x 4'' x 25''
75
#(+,
*#),('$))`$')(+,
2''
x
4''
x
23''
(4)
2-1/2'' screws
per board
75/
(4)
2
-1/2'' screws
per board
Slide Barrier Cont.
1. Install (2) 2'' x 4'' x 25'' Boards as shown in
(Fig. 7).
2. Install (2) 2'' x 4'' x 23'' Slide Support Boards on
the inside of your barrier as shown in (Fig. 7a).
2'' x 4'' x 25''
2'' x 4'' x 23''
15
Assembly Instructions
75
2'
'
x 4'
'
Cut T
o Width of Y
our
Unit
31-1/2''
Slide Barrier Cont.
1. Install a 2'' x 4'' board, cut to the width of your unit, as shown in (Fig. 8).
2-1/2''
screws
per joint
16
Assembly Instructions
1-1/4'' lag screws
2'' lag screws
Slide Installation
1. Lift and attach 5’ Turbo to units, as shown in
(Fig. 9).
Note: Two people will be required to properly
align the Turbo Tube Slide with your tower.
2. On either side of the Slide Entrance there is a
dimple. Insert (1) 2'' Screw in either side, so
that the screw goes into the support board
behind, as shown in (Fig. 9a).
3. Secure Elbow Bracket to 2'’ x 4'' as shown in
(Fig. 9b).
Note: The lower edge of the Elbow Bracket
must sit tightly against the top of the 2'' x 4''
support board.
' )($*!))
#()F
75
*#' +,
!*(
!*(
750
Approximate
1-1/4''
G
ap
2'' x 4''
2'' screw
per side
75/
2'' lag screws
5/16'' Flat
Washers
17
Assembly Instructions
*'
2" x 4" x 8-1/4"
2" x 4" x 11-1/4''
2" x 4" x 18"
2" x 4" x 18"
2-1/2" Screws
2-1/2" Screws
2" x 4" x 8-1/4"
(2) 2" Lag Screws
Support Bracket
75
75/
750
SUPPORT AND BRACKET
ASSEMBLY
1. Assemble the support base as shown in (Fig. 10).
2. Attach the support bracket to the support base using
two lag bolts (Fig. 10a).
NOTE: Pre-drill 1/8" pilot holes.
3. Place the support beneath the Exit and determine its
final position. NOTE: Slide support should fit tightly
beneath the slide to assure proper support. Remove
corresponding nut and bolt, attach support to the slide
as indicated in (Fig. 10b). Re-attach hardware.
4. Level grade at the bottom of the slide.
%@3@7::
Loc Nut
Washer
Hex Head
Bolt
FLUSH
19
Instrucciones de ensamblaje / Instructions d’assemblage
*'
2" x 4" x 8-1/4"
2" x 4" x 11-1/4''
2" x 4" x 18"
2" x 4" x 18"
T
ornillos de 2-1/2"
V
is de 2 1/2 po
T
ornillos de 2-1/2"
V
is de 2 1/2 po
2" x 4" x 8-1/4"
(2) Tornillo de
compresión de 2"
(2) Tire-fonds de 2 po
Abrazadera de soporte
Patte de support
75
75/
750
ENSAMBLAJE DEL APOYO Y DE LA
ABRAZADERA
1. Ensamble la base del soporte como se muestra en la (Fig. 10).
2. Una la abrazadera de soporte a la base del soporte usando
dos pernos con cabeza cuadrada (Fig. 10a)
NOTA: Perfore previamente los agujeros pilotos de 1/8".
3. Colocar el soporte por debajo de la salida y determinar su
ubicación final. NOTA: El soporte del tobogán debe encajar
firmemente por debajo del tobogán para asegurar un apoyo
adecuado. Retire la tuerca y el perno correspondientes y una
el soporte al tobogán como se indica en la (Fig. 10b).
Vuelva a colocar los herrajes.
4. Gradúe la pendiente en la parte inferior del tobogán.
ASSEMBLAGE DU SUPPORT ET DE LA
FIXATION
1. Assemblez la base de support comme indiqué sur la (Fig. 10).
2. Attachez la fixation de support à la base de support à l’aide
de deux tire-fonds (Fig. 10a).
REMARQUE : Percez d’abord des trous préliminaires de
guidage de 1/8 po.
3. Placez le support en dessous de la sortie de glissoire et
déterminez sa position finale. REMARQUE : Le support doit
s’ajuster parfaitement sous la glissoire pour offrir un support
adéquat. Retirez le boulon et l’écrou correspondants et fixez
le support à la glissoire comme indiqué sur la (Fig. 10b).
Posez de nouveau la quincaillerie.
4. Égalisez le sol à la sortie de la glissoire.
%3@4=@/17=<3A>@3D7/A
)@=C2N8L>3@1N
!
Tuerca de
seguridad
Contre-écrou
Arandela
Rondelle
Perno con
cabeza
hexagonal
Boulon à tête
hexagonale
NIVEL
À ÉGALITÉ
18
Instrucciones de ensamblaje / Instructions d’assemblage
t
ornillos de
compresión de 1-1/4"
T
ire-fonds de
1]1/4]po
Tornillos de
compresión
de 2"
Tire-fonds
de 2]po
Instalación del tobogán
1. Levante el Turbo de 5’ y únalo a las unidades, como se muestra en
la (Fig. 9).
Nota: Se necesitan dos personas para alinear el tobogán Turbo
Tube con la torre de forma apropiada.
2. Hay un hoyito en cada lado de la entrada del tobogán. Inserte (1)
tornillo de 2" en cualquiera de los dos lados, para que el tornillo
llegue a la tabla de soporte de atrás, como se muestra en la (Fig. 9a).
3. Asegure la abrazadera del codo a 2" x 4", como se muestra en la
(Fig. 9b).
Nota: El borde inferior de la abrazadera del codo debe apoyarse
firmemente contra la parte superior de la tabla de soporte de 2" x 4".
Installation de la glissade
1. Soulevez et fixez la glissoire Turbo Tube de 5 pi à l’unité, tel
qu’illustré sur la (Fig. 9).
Remarque : Il faut deux personnes pour aligner correctement la
glissoire Turbo Tube à votre tour.
2. Il y a une fossette de chaque côté de l’entrée de la glissoire. Insérez
(1) vis de 2 po de chaque côté, de sorte que la vis s’insère dans
la planche de support en arrière, tel qu’illustré sur la (Fig. 9a).
3. Fixez le support de coude de 2 po x 4 po tel qu’illustré sur la
(Fig. 9b).
Remarque : Le bord inférieur du support de coude doit s’appuyer
solidement contre le haut de la planche de support de 2 po x 4 po.
!'.'()'
%')$#)'F
!
(*%%$')$)[)'$!!IX
!%!#>=FW>=
75
+()%$'$
!%!)$'"
+**(($*(
!)''((
#+!
XI!)I
#+!
XI!)I
750
Abertura
1-1/4"
aproximada
Espace
d’environ
1 1/4 po
2'' x 4''
T
ornillo de 2"
por cada lado
Vis de 2]po
par côté
75/
!
!
Tornillo de
compresión de 2"
arandelas
p
lanas
de 5/16"
Tire-fonds de 2
po
Rondelles
plates
de 5/16]po
"
17
Instrucciones de ensamblaje / Instructions d’assemblage
75
2
"
x
4
"
Co
rt
e
se
g
ú
n
a
n
ch
o
d
e
su
u
n
id
a
d
2
p
o
]
x]
4
]
p
o
Co
u
p
e
z
à
la
la
rg
e
u
r
d
e
vo
t
re
u
n
it
é
31-1/2''
Barrera del tobogán (cont.)
1. Instale una tabla de 2" x 4", corte al ancho de su unidad, como se muestra en la (Fig. 8).
Construction de la barrière de la glissoire, suite
1. Installez une planche 2 po x 4 po, coupez à la largeur de votre unité, tel qu’illustré sur la (Fig. 8).
Tornillos
de 2-1/2
Vis de 2 1/2 po
par joint
16
Instrucciones de ensamblaje / Instructions d’assemblage
2'' x 4'' x 25''
75
+()#)'#
(.$''!*#%'
$)#'()+()
+*!Z#)I'*'
))!!*()')$#%'I(#)
!Z#("!%+$)IU
2''
x
4''
x
23''
(4)
Tornillos de
2-1/2"
por tabla
(4)
Vis de
2 1/2 po
par planche
75/
(4)
Tornillos de
2
-1/2"
por tabla
(4)
V
is de
2 1/2 po par
planche
Barrera del tobogán (cont.)
1. Instale las (2) tablas de 2" x 4" x 25" como se
muestra en la (Fig. 7).
2. Instale las (2) tablas de soporte del tobogán de
2" x 4" x 23" en el interior de la barrera como
se muestra en la (Fig. 7a).
Construction de la barrière de la
glissoire, suite
1. Installez (2) planches de 2 po x 4 po x 25 po
tel qu’illustré sur la (Fig. 7).
2. Installez (2) planches de support de glissoire
de 2 po x 4 po x 23 po à l’intérieur de votre
barrière, tel qu’illustré sur la (Fig. 7a).
2'' x 4'' x 25''
2" x 4" x 23"
Instrucciones de ensamblaje / Instructions d’assemblage
15
75
Construcción de la barrera del tobogán
1. Retire con cuidado las tablas de soporte de la barrera donde desea
colocar el tobogán, asegurándose de tener una zona de seguridad
despejada de 72" para el tobogán. (Fig. 6).
Guarde la madera y los sujetadores porque los necesitará en los pasos
siguientes.
2. Cortar a medida e instalar (2) tablas de soporte de la barrera de 2" x
4" como se muestra en la (Fig. 6a), asegurándose de que la abertura
que quede entre ellas sea de 25".
3. Corte (1) tabla de barrera de 2" x 4" a la altura de los rieles de su
barrera y cree una apertura de tobogán de 23", como se muestra en la
(Fig. 6a).
4. Vuelva a unir las tablas de barrera asegurándose de que el espacio
que quede entre ellas sea parejo, y que no quede un agujero que supere
las 3" entre cada tabla, como se muestra en la (Fig. 6a).
Construction de la barrière de la glissoire
1. Retirez délicatement vos planches de support de la barrière là où vous
souhaitez installer votre glissoire, en vous assurant de conserver un espace
de sécurité dégagé de 72 po pour la glissoire (Fig. 6).
Conservez ces planches et attaches puisque vous en aurez besoin
ultérieurement.
2. Coupez à la longueur et installez les (2) supports des planches de
barrière de 2 po x 4 po tel qu’illustré sur la (Fig. 6a) en vous assurant
que l’espace entre les planches soit de 25 po.
3. Coupez (1) planche de barrière de 2 po x 4 po à la hauteur de votre
rampe de barrière et créez une ouverture de 23 po pour la glissoire, tel
qu’illustré sur la (Fig. 6a).
4. Fixez à nouveau vos planches de barrière, en vous assurant qu’elles
sont également espacées et ne présentent pas d’espace supérieur à 3 po
entre chaque planche, tel qu’illustré sur la (Fig. 6a).
75/
2-1/2"
tornillos
por junta
Vis de 2 1/2 po
par joint
25''
23''
Abertura de
3-1/4" entre cada tabla
de la barrera
Espace de 3]1/4]po
entre chaque planche
de barrière
2" x 4"
Corte según ancho de su unidad
2 po]x]4]po
Coupez à la largeur de votre unité
#$)
AB3>:/<=CB7:7H/C</B=@@353<N@71/>/@/
7:CAB@/@3:B=0=5K<)C@0=)C0323Z?C3
3ABKB@/B/<2=23C<7@3B=2=A;=2=A
3AB3;7A;=>@=1327;73<B=>C323
A35C7@A3>/@/1C/:?C73@3?C7>=238C35=
1=<B=@@323Z23(E7<5#(:723
'"'&*W
3>:/<CB7:7A3C<3B=C@AB/<2/@2>=C@
7::CAB@3@:/47F/B7=<23:/5:7AA=7@3)C@0=
)C0323W>7)=CB34=7A:/;P;3
>@=1N2C@32=7BPB@33;>:=GN3>=C@B=CB
3<A3;0:32383C(E7<5#(:723
LB=C@23W>7
Altura de Plataforma de 5'
Hauteur de plate-forme de 5 pi
2-1/2"
tornillos
por cada tabla
de barrera
Vis de 2 1/2 po
par planche de
barrière
2
"
x
4
"
Co
rt
e
se
g
ú
n
a
n
ch
o
d
e
su
u
n
id
a
d
2
p
o
]
x]
4
]
p
o
Co
u
p
e
z
à
la
la
rg
e
u
r
d
e
vo
t
re
u
n
it
é
2" x 4"
Tabla de barrera
Corte a la altura del riel
Planche de barrière
de 2 po x 4 po
Coupez à la hauteur
de la rampe
14
Instrucciones de ensamblaje / Instructions d’assemblage
75/
Salida del tobogán
1. Alinee la sección de salida del codo para que el agujero n.° 1 quede
alineado con la abertura de la pestaña, como se muestra en la
(Fig. 5) y la (Fig. 5b) y ubíquelo en su lugar.
2. Fije la salida con la sección de salida del codo para que la parte
superior de la salida coincida con las uniones, como se muestra en
la (Fig. 5c) y ubíquela en su lugar.
3. Ajuste todos los herrajes.
NOTA: El diseño entrelazado de las pestañas en las piezas del codo
lo ayudará en el ensamblaje.
Sortie de la glissoire
1. Alignez la section de coude de sortie de sorte que le trou n° 1 s’aligne
avec l’ouverture de la bride, tel qu’illustré sur les (Fig. 5) et (Fig. 5b)
et fixez-la.
2. Fixez la sortie à la section du coude de sortie de sorte que le haut de la
sortie soit aligné avec les bords, tel qu’illustré sur la (Fig. 5c) et fixez-la.
3. Serrez toute la quincaillerie.
REMARQUE : Le concept d’interverrouillage des brides sur les parties du
coude vous aidera lors de l’assemblage.
S
ecciones de codo de salida - 12 pernos
Section de sortie – 12 boulons
Salida - 6 pernos
Sortie – 6 boulons
75
Agujero n.º 1
Trou n
o
1
750
751
Alinee el borde superior de la
base del tobogán con la unión de
la sección de salida.
Alignez le bord supérieur de la
base de la glissoire avec le bord
de la section de sortie.
Perno con cabeza hexagonal
Boulon à tête hexagonale
A
randela
Rondelle
A
randela
Rondelle
T
uerca de seguridad
Contre-écrou
Apertura de la pestaña
Ouverture de bride
Instrucciones de ensamblaje / Instructions d’assemblage
13
75/
Codos del tobogán
1. Alinee el tercer codo para que el agujero n.º 1 quede alineado con
la apertura de la pestaña, como lo muestra la (Fig. 4) y la (Fig. 4c)
y ubíquelo en su lugar.
2. Alinee el cuarto codo para que el agujero n.º 1 quede alineado con
la apertura de la pestaña, como lo muestra la (Fig. 4b) y la (Fig. 4c)
y ubíquelo en su lugar.
NOTA: El diseño entrelazado de las pestañas en las piezas del codo lo
ayudará en el ensamblaje.
NOTA: Solo las tuercas de seguridad se deben apretar con los dedos.
Coudes de la glissoire
1. Alignez le troisième coude de sorte que le trou n° 1 s’aligne avec
l’ouverture de la bride illustrée sur les (Fig. 4) et (Fig. 4c) et fixez-le.
2. Alignez le quatrième coude de sorte que le trou n° 1 s’aligne avec
l’ouverture de la bride illustrée sur les (Fig. 4b) et (Fig. 4c) et fixez-le.
REMARQUE : Le concept d’interverrouillage des brides sur les parties du
coude vous aidera lors de l’assemblage.
REMARQUE : Serrez à la main les contre-écrous seulement.
Sección de codo - 12 pernos
Section en coude – 12 boulons
75
750
Apertura de la pestaña
Ouverture de bride
Agujero n.º
1Trou n
o
1
751
Sección de codo - 12 pernos
Section en coude – 12 boulons
Perno con cabeza hexagonal
Boulon à tête hexagonale
A
randela
R
ondelle
A
randela
Rondelle
Tuerca de seguridad
C
ontre-écrou
12
Instrucciones de ensamblaje / Instructions d’assemblage
Codos del tobogán
1. Alinee el primer codo con la sección de entrada con las uniones
alineadas y la salida hacia abajo. Rote los (2) agujeros del codo hacia
la derecha como se muestra en la (Fig. 3) y ubíquelos en su lugar.
Busque la abertura de la pestaña como lo muestra la (Fig. 3a).
2. Alinee el segundo codo para que el agujero n.° 1 quede alineado con la
apertura de la pestaña, como lo muestra la (Fig. 3c) y la (Fig. 3d) y
ubíquelo en su lugar.
NOTA: El diseño entrelazado de las pestañas en las piezas del codo lo
ayudará en el ensamblaje.
NOTA: Solo las tuercas de seguridad se deben apretar con los dedos.
Coudes de la glissoire
1. Alignez la première section de coude avec la section d’entrée, avec les
bords alignés et la section de sortie vers le bas. Faites tourner les (2)
orifices du coude vers la droite tel qu’illustré sur la (Fig. 3) et fixez-les.
Recherchez l’ouverture de la bride illustrée sur la (Fig. 3a).
2. Alignez le second coude de sorte que le trou n° 1 s’aligne avec
l’ouverture de la bride illustrée sur les (Fig. 3c) et (Fig. 3d) et fixez-le.
REMARQUE : Le concept d’interverrouillage des brides sur les parties du
coude vous aidera lors de l’assemblage.
REMARQUE : Serrez à la main les contre-écrous seulement.
Sección de codo - 12 pernos
S
ection en coude – 12 boulons
Sección de codo - 12 pernos
Section en coude – 12 boulons
751
Trou n
o
1
>3@BC@/23:/>3AB/R/
$CD3@BC@3230@723
75
>3@BC@/23
:/>3AB/R/
$CD3@BC@3
230@723
75/
752
750
Perno con cabeza hexagonal
Boulon à tête hexagonale
Arandela
R
ondelle
Arandela
R
ondelle
T
uerca de seguridad
Contre-écrou
)!!!%()J
I)!!'
11
Instrucciones de ensamblaje / Instructions d’assemblage
75/
75
750
Sección de salida - 9 pernos
Section de sortie – 9 boulons
Secciones de 9 codos cada una
S
ection en coude – 9 boulons chacune
F
ENSAMBLAJE DE LAS SECCIONES DE SALIDA Y DEL CODO
1. Ensamble la sección de los codos asegurándolos como se muestra en la (Fig. 2) y
la (Fig. 2a). Una las secciones con un perno de cabeza hexagonal, dos arandelas
planas y una tuerca de seguridad en cada unión de agujeros.
NOTA: Apriete fuerte cada tuerca de seguridad con los dedos. Cada vez que junte
las partes, asegúrese de que cada borde de pestaña coincida con un borde plano.
2. Repita el paso 1 para ensamblar las (3) secciones de codos restantes.
3. Ensamble y asegure la sección de salida como se muestra en la
(Fig. 2a) y la (Fig. 2b). Asegúrese de fijar la abrazadera de soporte del
codo a la parte inferior de la pestaña, como se muestra en la (Fig. 2b).
4. Ajuste todos los herrajes.
NOTA: El diseño entrelazado de las pestañas en las piezas del codo lo ayudará en
el ensamblaje.
ASSEMBLAGE DE LA SECTION EN COUDE ET DE LA SORTIE
1. Assemblez la section du coude en la fixant tel qu’illustré sur les (Fig. 2) et
(Fig. 2a). Joignez les sections à l’aide d’un boulon à tête hexagonale, deux
rondelles plates et un contre-écrou à la jonction de chaque trou.
REMARQUE : Serrez bien à la main chaque contre-écrou. À chaque fois qu’une
section est jointe, assurez-vous que chaque bride avec rebord s’accouple avec
une bride plate.
2. Répétez l’étape 1 pour assembler les (3) sections de coude restantes.
3. Assemblez et fixez la section de la sortie en la fixant tel qu’illustré sur les
(Fig. 2a) et (Fig. 2b). Assurez-vous de fixer la fixation de support du coude
au bas de la bride, tel qu’illustré sur la (Fig. 2b).
4. Serrez toute quincaillerie.
REMARQUE : Le concept d’interverrouillage des brides sur les parties du coude vous aidera
lors de l’assemblage.
)!!!%()J
I)!!'
>3@BC@/23:/>3AB/R/
$CD3@BC@3230@723
P
erno con cabeza hexagonal
Boulon à tête hexagonale
A
randela
Rondelle
Arandela
R
ondelle
T
uerca de seguridad
Contre-écrou
Coderas
Abrazadera
Fixation de
support
de coude
10
Instrucciones de ensamblaje / Instructions d’assemblage
75
ENSAMBLAJE DE LA SECCIÓN DE ENTRADA
NOTAS:
• Se necesitan por lo menos dos personas para armar el tobogán Turbo Tube de 5’.
• Para ayudar a alinear los agujeros al unir las secciones, se debe introducir un destornillador a través de los agujeros adyacentes para mantener la
alineación de estos.
1. Ensamble la sección de entrada asegurando primero la unión superior, como se muestra en la (Fig. 1) y la (Fig. 1a). Una las secciones con un perno de
cabeza hexagonal, dos arandelas planas y una tuerca de seguridad en cada unión de agujeros.
2. Cuando asegure la unión inferior asegúrese de fijar la abrazadera de entrada al lado izquierdo de la unión como se muestra en la (Fig. 1),
ubicándolo en su lugar como se muestra en la (Fig. 1a).
3. Ajuste todos los herrajes.
ASSEMBLAGE DE LA SECTION D’ENTRÉE
REMARQUES :
• Il faut au moins deux personnes pour assembler la glissoire Turbo Tube de 5 pi.
• Pour faciliter l’alignement des trous lors de l’assemblage des sections, insérez un tournevis dans les trous adjacents pour maintenir l’alignement.
1. Assemblez la section d’entrée en fixant le bord supérieur en premier, tel qu’illustré sur les (Fig. 1) et (Fig. 1a). Joignez les sections à l’aide d’un boulon à
tête hexagonale, deux rondelles plates et un contre-écrou à la jonction de chaque trou.
2. En fixant le bord inférieur, assurez-vous d’attacher la fixation d’entrée du côté gauche, tel qu’illustré sur la (Fig. 1), en la fixant de la manière indiquée
sur la (Fig. 1a).
3. Serrez toute quincaillerie.
P
erno con cabeza hexagonal
B
oulon à tête hexagonale
Arandela
R
ondelle
Arandela
R
ondelle
T
uerca de seguridad
Contre-écrou
Sección de entrada - 8]pernos
Section d’entrée – 8 boulons
Abrazadera de entrada
Fixation d’entrée
75/
9
Pieza de entrada del lado izquierdo
Panneau d’entrée gauche
Pieza de entrada del lado derecho
Panneau d’entrée droit
Codo
Coude
Codo de salida
Coude de sortie
Salida
Sortie
Coderas Abrazadera
Fixation de support
de coude
Abrazadera de entrada
Fixation d’entrée
$"%$##)(!)$$\#$"%$(#)(!!(($'
Abrazadera de soporte en T
Fixation de support de barre en T
8
HERRAMIENTAS REQUERIDAS / OUTILS REQUIS
(1) 2'' x 4'' x 96''
25''
25''
23'' 23''
(1) 2'' x 4'' x 96''
18'' 18'' 18''
11-1/4''
8-1/4'' 8-1/4''
(2) 2'' x 4'' x 96''
MADERA NECESARIA/BOIS D'ŒUVRE REQUIS : (4) 2'' x 4'' x 96''
(*'
I&*''
('''*!'
(
'*!'
)!'$
%
'*(
#)"I)'
'
*#X"(*''
((*'
-"\('#)%$!+$
!*#))((I*')I
)"(&*
#)%$*((]'(
*$($#*#
!
!+*$(
$*!!)!IX"$!))
W%$
arandelas planas
de 5/16"
Rondelles plates
de 5/16]po
tuercas de
seguridad
de 5/16"
Contre-écrous
de 5/16]po
pernos de cabeza
hexagonal de 5/16" x 3/4"
Boulons à tête hexagonale
de 5/16]po x]3/4]po
tornillos para madera de 2-1/2"
Vis à bois de 2]1/2]po
tornillo para madera de 2"
Vis à bois de 2 po
tornillo de compresión de 2"
Tire-fonds de 2 po
(#!*-#!$(($'$(&*#!!'$"%'(
tornillos de compresión de 1-1/4"
Tire-fonds de 1 1/4 po
broca T30 Torx
®
Foret Torx
MD
T30
broca T20 Torx
®
Foret Torx
MD
T20
!()$')"'(!()($*%($(ZY*+'
!"'$#!($"%'%$'(%'$$(ZY*+'(*%%!I"#)'X)'(I%'I"#)
!
!+*$(
!I#!(
Este producto ha sido ideado para su uso en una residencia u hogar de una sola familia y no para usarse en lugares públicos.
Su uso en lugares públicos constituye una mala utilización de este producto.
¡IMPORTANTE!
INSTRUCCIONES ADICIONALES DE SEGURIDAD PARA LA INSTALACIÓN
Según establece la Sociedad Americana de Pruebas y Materiales (American Society for Testing and Materials, ASTM), todos los equipos deben anclarse al suelo y, si la unidad tiene además una cuerda
p
ara escalar, el extremo de la cuerda deberá anclarse al suelo. Si las condiciones del terreno permiten que las estacas se salgan con facilidad, será entonces necesario cementarlas al suelo.
•
Para anclar la unidad al suelo, siga las instrucciones contenidas en el presente plan para aplicar los dispositivos de anclaje a su unidad, o utilice estacas tratadas a presión de 2" x 4" x
1
8"(45mm x 95mm x 457mm). Martille las estacas en el suelo a una profundidad de al menos 12" (305 mm) en todas las esquinas internas de los postes (incluidas las patas del marco en A y
l
os postes de la unidad para escalar). Fije con cuatro (4) clavos galvanizados de 16D (3-1/2") por estaca en cada poste de la torre y/o del marco en “A”.
• Si la unidad incluye una soga para escalar, ancla la soga en ambos extremos.
•
Una vez que la unidad esté completamente armada y antes de que se le permita a los niños jugar en ella, se debe instalar una superficie de material adecuado para
a
mortiguar golpes. Esto se consigue usando materiales de relleno suelto a una profundidad adecuada. La “Guía para la seguridad en las zonas de recreo públicas” (Handbook for Public
P
layground Safety) publicada por la Comisión de Seguridad para los Productos de Consumo (Consumer Product Safety Commission, CPSC) cita los siguientes materiales y las profundidades
r
equeridas que se consideran suficientes para uso en residencias y hogares. Información adicional puede encontrarse en ASTM F1292.Para protegerse de caídas de hasta 9 pies (2.742m) de
altura [recomendado para los equipos Swing•N•Slide]:
MATERIALES DE RELLENO SUELTO PROFUNDIDAD (SIN COMPRIMIR) REQUERIDA
1
pulgada (mm)
M
antillo de madera 9" (229 mm)
Mantillo de corteza de doble trituración 9" (229 mm)
Viruta de madera uniforme 12" (305 mm)
E
stas profundidades se han extraído de la Guía de la CPSC. Swing•N•Slide no ha realizado estudios independientes para determinar estas profundidades recomendadas.
Cuando el material para amortiguar golpes se instala adecuadamente, éste cubre completamente todas las superficies horizontales de las unidades para escalar. Esta superficie protectora
deberá extenderse al menos 6 pies (1.828mm) en todas las direcciones, desde el perímetro del equipo o desde los bordes externos de cualquiera de los componentes. Por ejemplo, un
tobogán que se extiende por fuera de la plataforma deberá tener una superficie protectora de al menos 6 pies (1.828mm) a ambos lados y en el extremo. Para columpios, la superficie
protectora se debe extender por lo menos 14 pies (6 m) a partir de tanto la parte trasera
como
delantera del columpio cuando éste se encuentre en posición de reposo.
GARANTÍA LIMITADA DEL FABRICANTE DE Swing-N-Slide
®
Swing-N-Slide® se enorgullece de la calidad y la durabilidad de nuestros productos. Nuestra garantía limitada del fabricante ofrece confianza y demuestra
nuestro compromiso con la entrega de productos de calidad para zonas de recreo residenciales.
GARANTÍA LIMITADA DE POR VIDA DEL FABRICANTE
Swing-N-Slide® garantiza que sus toboganes termoformados y montañas para escalar estarán libres de defectos de mano de obra y materiales, bajo condiciones y
uso normales, durante la vida útil del producto.
GARANTÍA LIMITADA DE 5 AÑOS DEL FABRICANTE
Swing-N-Slide® garantiza que sus kits de conjunto de juegos personalizados listos para armar y sus accesorios permanecerán libres de defectos de mano de
obra y materiales, bajo condiciones y uso normales, durante un período de 5 años.
GARANTÍA LIMITADA DE 5 AÑOS DEL FABRICANTE
Swing-N-Slide® garantiza que sus kits de conjunto de juegos No-Cut and Wood Complete Ready-to-Assemble Play Set no experimentarán deterioro debido
a putrefacción de la madera o termitas, y que permanecerán libres de defectos de mano de obra y materiales, bajo condiciones y uso normales, durante un
período de 5 años en el caso de los componentes estructurales de madera.
Los defectos estéticos que no afecten la integridad estructural del producto o los defectos naturales de la madera como la torsión, la rajadura, la fisuración, el
pandeo, contracción, hinchamiento o cualquier otra propiedad física de la madera que no presente un riesgo de seguridad, no están cubiertos por esta garantía.
GARANTÍA DE UN AÑO DEL FABRICANTE
Swing-N-Slide® garantiza que sus techos y/o lonas impermeabilizadas de cubierta y envoltura para madera Timber-GLOVE permanecerán libres de defectos de
mano de obra y materiales, bajo condiciones y uso normales, durante un período de un año.
Swing-N-Slide® reparará, o según su criterio, reemplazará, dentro del período de garantía señalado, cualquier pieza que presente defectos de mano de obra o
materiales. Esta decisión está sujeta a verificación del defecto luego del envío de la pieza defectuosa a Swing-N-Slide® a 1212 Barberry Drive, Janesville,
Wisconsin, 53545. Toda pieza devuelta a Swing-N-Slide® primero debe tener un Número de autorización de devolución aprobado y una prueba de compra,
incluida la fecha de compra. Esta garantía es válida sólo si el producto se utiliza para el objetivo que se diseñó y se instala en una vivienda unifamiliar residencial.
Esta garantía queda nula si al producto se le da un uso comercial o institucional. Esta garantía no cubre (a) productos que hayan sido dañados por hechos de la
naturaleza, negligencia, uso indebido o accidente, o que hayan sido modificados o reparados por personas no autorizadas; (b) el costo de la mano de obra o el
costo de envío del producto, alguna pieza o un producto o pieza de reemplazo.
Swing-N-Slide® DESCONOCE TODAS LAS DEMÁS DECLARACIONES Y GARANTÍAS DE CUALQUIER TIPO, EXPRESAS, IMPLÍCITAS, ESTATUTARIAS U OTRAS,
INCLUIDAS LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILIDAD Y APTITUD PARA UN FIN ESPECÍFICO. Swing-N-Slide® NO SERÁ RESPONSABLE DE NINGÚN DAÑO
FORTUITO O CONSECUENTE. Esta garantía no es transferible y no se extiende a los propietarios del producto posteriores al comprador original. Algunos estados
no permiten limitaciones en las garantías implícitas ni la exclusión de daños fortuitos o consecuentes, por tanto es posible que estas restricciones no se apliquen
en su caso. Esta garantía le otorga derechos legales específicos. Es posible que tenga otros derechos, que pueden variar de un estado a otro.
Esta garantía tampoco se aplica a:
• Estructuras no levantadas, mantenidas ni inspeccionadas en conformidad con los planos de instalación de Swing-N-Slide®
• Estructuras en las que se ha agregado o sustituido piezas que no están en conformidad con los planos de instalación de Swing-N-Slide®
• Piezas que se han modificado, alterado o usado indebidamente
• Piezas que no se han usado según su diseño u objetivo
• Daño debido a hechos de la naturaleza, vandalismo, uso anormal o abuso según lo determine Swing-N-Slide®
%/@/=0B3<3@7<4=@;/17S</2717=</:A=0@3A35C@72/23<:/AH=</A23@31@3=
la Comisión de Seguridad para los Productos de
Consumo (Consumer Product Safety Commission, CPSC) publica el Manual para la seguridad en las zonas de recreo domésticas al aire
libre (Outdoor Home Playground Safety Handbook) que se puede descargar en forma gratuita de EEE1>A15=D. Un recurso adicional es la
Especificación Estándar de Rendimiento de la Seguridad del Consumidor de la Sociedad de EE. UU. de Pruebas y Materiales (ASTM)
Para Equipos de Patios de Recreo en el Hogar (ASTM F1148) que se puede adquirir y descargar en EEE/AB;=@5.
7
6
L
iste de vérification de sécurité pour les ensembles de jeu et les accessoires Swing-N-Slide
¡Importante!
Instrucciones de seguridad adicionales para todos los equipos de juego Swing-N-Slide.
Guardar esta hoja de instrucciones en caso de que se requiera contactar al fabricante.
A
tender los siguientes enunciados y advertencias reduce la posibilidad de lesiones graves o fatales.
Seguridad durante la instalación – Usted:
¿
Ha consultado las instrucciones de ensamblaje suministradas con su modelo en particular?
¿
Ha notado que este accesorio se debe usar solamente con diseños aprobados por Swing•N•Slide? (No altere su diseño ni añada/retire componentes).
¿Se ha asegurado de que todos los accesorios hayan sido ajustados firmemente? (Las cubiertas de los pernos suministradas también se deben
a
segurar firmemente).
¿
Se ha asegurado de cortar con una sierra de mano todos los extremos roscados sobresalientes de los pernos y demás sujetadores, así como de haber eliminado
cualquier borde filoso usando una lima para metales, según haya sido necesario, y recubierto los extremos de los sujetadores con pintura sin plomo?
¿Ha colocado el equipo a nivel del piso, a no menos de seis pies (1.8 metros) de cualquier estructura u obstrucción tal como una cerca, garaje, casa,
r
amas colgantes, sogas para tender la ropa o cables eléctricos?
¿
Se ha asegurado de que el equipo de juego no haya sido instalado sobre concreto, asfalto, tierra prensada o cualquier otra superficie dura?
(Una caída sobre una superficie dura puede provocar una lesión grave al usuario del equipo).
¿Ha verificado que las cuerdas para escalar, la cadena o el cable suspendidos estén sujetados en ambos extremos?
¿
Ha consultado las zonas mínimas de uso en las instrucciones de ensamblaje de su modelo en particular?
¿Ha usado un sellador de agua en su conjunto de juego para proteger la madera y prevenir que se agriete y se tuerza?
¿Ha seguido todos los requisitos que se encuentran en el reverso de esta página relacionados con el anclaje y el recubrimiento amortiguador de golpes,
s
egún corresponda?
¿
Se ha asegurado de no permitir que los niños usen los equipos hasta que éstos queden correctamente instalados?
¿Se ha asegurado de ajustar todos los columpios de manera que haya un espacio mínimo de 8'' entre el columpio y la superficie del suelo?
Seguridad durante la operación – Usted:
¿
Se ha asegurado de que en el sitio de juegos haya supervisión por parte de un adulto para los niños de todas las edades?
Antes de permitirles usar los equipos, ¿les ha enseñado a los niños lo siguiente? No caminar cerca, enfrente, por detrás o entre objetos móviles.
No retorcer el columpio ni cualquiera de las cadenas o cuerdas accesorias ni enrollarlas sobre la barra de soporte superior, ya que esto reduciría la
f
uerza de la cadena o la cuerda.
N
o columpiar los asientos vacíos u otros accesorios.
No deslizarse hacia abajo por las cadenas de los columpios.
Asegurarse de sentarse en el centro del columpio y en los otros accesorios, con todo el peso sobre el asiento.
No unir accesorios al equipo de juego que no estén diseñados específicamente para el mismo, como los siguientes, entre otros: cuerdas para saltar,
sogas para tender la ropa, correas para mascotas, cables y cadenas. Éstos pueden provocar peligro de estrangulamiento.
No trepar ni caminar sobre la parte superior de las vigas de los columpios, los pasamanos o el techo.
No usar los equipos de manera diferente a aquella para la cual fueron diseñados.
No saltar de los equipos cuando están en movimiento.
No subirse a los equipos cuando estén mojados.
Asegurarse de bajar por los toboganes con los pies por delante.
¿Ha determinado que sólo se puede permitir un niño por asiento en un mismo momento?
¿Has determinado que los niños deben estar vestidos en forma adecuada para el juego? Evita chaquetas con capucha, cascos para bicicletas u otros
deportes, ropa con cordones y suelta que podría hacer que se enreden o se enganchen en el equipo.
¿Has determinado que las sogas, cadenas o cables para escalar están anclados firmemente en ambos extremos y no pueden entrelazarse?
¿Se ha asegurado de que el tobogán se ubique de manera que no esté bajo la luz directa del sol?
Mantenimiento de Seguridad–Sigue estas instrucciones preventivas de mantenimiento en los intervalos
requeridos:
Para evitar el deterioro de los materiales, retira los asientos de plástico de los columpios y otros accesorios de plástico cuando la temperatura exterior
baje a 32° F o menos y llévalos a un lugar bajo techado. Reinstala estos elementos plásticos al inicio de cada temporada de juego.
Al inicio de cada temporada de juego verifica que las piezas de metal no se hayan oxidado. Si se encuentran indicios de corrosión, lija y vuelve a pintar
usando una pintura que no sea a base de plomo y que cumpla con los requisitos 16 CFR 1303 o SOR/2005-109.
Al inicio de cada temporada de juego y una vez al mes durante la misma, verifica que las piezas movibles no se hayan desgastado, oxidado o
deteriorado de otra manera. Reemplázala si es necesario. Si existe alguna de estas condiciones, llama al 1-800-888-1232 para ordenar los accesorios de
repuesto.
Al inicio de cada temporada de juego y una vez al mes durante la misma, lubrica las piezas de metal en movimiento.
Al inicio de cada temporada de juego y dos veces al mes durante la misma, revisa todas las cubiertas protectores de pernos, tubos, bordes y esquinas.
Reemplázalas si están sueltas, rotas o si faltan.
Al inicio de cada temporada de juego y dos veces al mes durante la misma, rastrilla y verifica la profundidad del material protector de relleno de superficies
para que no esté flojo, evitar la compactación y mantener la profundidad adecuada. Reemplaza según sea necesario.
Al inicio de cada temporada de juego y dos veces al mes durante la misma, ajusta todos los herrajes.
Al inicio de cada temporada de juego y una vez al mes durante misma, verifica que las piezas de madera no estén deterioradas y astilladas. Lija las
astilladuras y reemplaza las partes de madera deterioradas.
Instrucciones de desecho
Cuando el equipo sea retirado de servicio, se debe desarmar y desechar de tal manera que no presente peligros no razonables al momento de desecharlo.
Ce produit est destiné à un usage résidentiel et familial seulement et n'est pas conçu pour une utilisation dans un endroit public.
L'installation de ce centre de jeu dans un endroit public constitue une mauvaise utilisation de ce produit.
I
MPORTANT!
I
NSTRUCTIONS SUPPLÉMENTAIRES POUR UNE INSTALLATION SÉCURITAIRE
L
es normes établies par l’organisme américain ASTM spécifient que toutes les unités de jeu doivent être ancrées solidement au sol et que si l’unité comprend une corde d’escalade,
l
’extrémité de celle-ci doit également être ancrée au sol. Si les conditions de sol permettent aux piquets d’ancrage d’être arrachés facilement, ceux-ci devront être encastrés dans du
b
éton.
• Pour ancrer l’unité au sol, respecter les instructions incluses dans le présent plan concernant l’utilisation des ancrages « Anchor-It » à votre unité, ou utiliser des piquets en bois
traité sous pression de 2 x 4 x 18 po (45 x 95 x 457 mm). Enfoncer les piquets dans le sol à au moins 12 po (305 mm) à chacun des coins intérieurs des poteaux (incluant les pattes
d
es cadres en « A » et les poteaux des ensembles d’escalade). Fixer au moyen de quatre (4) clous galvanisés 16D de 3,5 po (89 mm) par piquet dans chaque montant de tour et(ou)
c
adre en A.
•
Si l'unité comporte une corde d'escalade, ancrez solidement cette corde aux deux bouts.
• Une fois le centre de jeu complètement assemblé et avant de permettre aux enfants d'y jouer, un matériau de surfaçage pouvant absorber les chocs doit être
installé. Cela peut être réalisé par l’utilisation d’un matériau de remplissage en vrac d’une épaisseur suffisante. Le manuel « Handbook for Public Playground Safety »
de la commission de la sécurité des produits de consommation (Consumer Product Safety Commission, CPSC) fait l’énumération des matériaux suivants et définit les épaisseurs
minimales pour des applications résidentielles. On peut trouver des informations complémentaires dans le document ASTM F1292. Pour une protection antichute allant jusqu’à
9 pi (2,74 m) [recommandée pour les ensembles Swing•N•Slide] :
M
ATÉRIAUX DE REMPLISSAGE EN VRAC
P
ROFONDEUR REQUISE (NON COMPACTÉE) 1 PO (25 MM)
Paillis de bois 9" (229mm)
P
aillis d’écorce à déchiquetage double 9" (229mm)
C
opeaux de bois uniformes 12" (305mm)
Ces épaisseurs proviennent du manuel de la CSPC. Pour déterminer ces profondeurs, Swing•N•Slide n’a réalisé aucun test indépendant.
L
orsqu’il est adéquatement installé, le matériau de surfaçage pour absorption de choc devrait recouvrir complètement les bases de bois horizontales des ensembles d’escalade. Ces
surfaces protectrices doivent s’étendre jusqu’à un minimum de 6 pi (1,828 m) dans toutes les directions à partir du périmètre de l’équipement ou de la limite extérieure de tout
composant. Par exemple, une glissoire s’étendant au-delà de la plate-forme doit comporter une surface protectrice sur au moins 6 pi (1,828 m) sur les deux côtés, de même qu’à son
extrémité. Pour les balançoires, la surface de protection doit s’étendre d’au moins 14 pi (6 m) à partir de l’avant et de l’arrière de la balançoire lorsqu’elle est en position de repos.
GARANTIE LIMITÉE DU FABRICANT Swing-N-Slide®
Swing-N-Slide® est fière de la qualité et de la durabilité de ses produits. Notre garantie limitée du fabricant donne l'assurance et démontre notre engagement envers la
fabrication d'articles pour terrain de jeu résidentiel de qualité.
GARANTIE LIMITÉE À VIE DU FABRICANT
Swing-N-Slide® garantit ses glissoires thermoformées et murs d’escalade contre toute défectuosité de matériaux et de fabrication, lorsqu'utilisés dans des conditions et
pour un usage normaux, pour la durée de vie du produit.
GARANTIE LIMITÉE DE CINQ (5) ANS DU FABRICANT
Swing-N-Slide® garantit ses ensembles et accessoires de jeu personnalisés prêt-à-monter contre toute défectuosité de matériaux et de fabrication, lorsqu'utilisés dans des
conditions et pour un usage normaux, pour une période de cinq (5) ans.
GARANTIE LIMITÉE DE CINQ (5) ANS DU FABRICANT
Swing-N-Slide® garantit les composants structurels en bois de ses ensembles et accessoires de jeu sans coupe et tout bois contre les dommages causés par la pourriture
et les termites, et contre toute défectuosité de matériaux et de fabrication, lorsqu'utilisés dans des conditions et pour un usage normaux, pour une période de cinq (5) ans.
Les défauts de fabrication apparents qui n'influencent pas l'intégrité structurale du produit, ou les défauts naturels du bois tels que la déformation, les fissures, les
gerçures, la torsion, le retrait, l'enflure ou d'autres propriétés physiques du bois qui ne constituent pas un danger pour la sécurité, ne sont pas couverts par cette garantie.
GARANTIE D'UN (1) AN DU FABRICANT
Swing-N-Slide® garantit ses bâches de toit et/ou ses bâches, et la toile protectrice pour bois Timber GLOVE contre toute défectuosité de matériaux et de fabrication,
lorsqu'utilisés dans des conditions et pour un usage normaux, pour une période d'un (1) an.
Swing-N-Slide® réparera, ou à sa discrétion, remplacera toute pièce présentant un défaut de matériaux et de fabrication au cours de la période de garantie mentionnée.
Cette décision est sous réserve d'une vérification de la défectuosité à la livraison de la pièce défectueuse à Swing-N-Slide® à 1212 Barberry Drive, Janesville,
Wisconsin, 53545 É.-U. Toute pièce retournée à Swing-N-Slide® doit être accompagnée d'un numéro d'autorisation de retour approuvé au préalable et d'une preuve
d'achat datée. Cette garantie est valide uniquement si le produit est utilisé aux fins pour lesquelles il est conçu et s'il est installé sur un terrain unifamilial et résidentiel. Elle
est nulle si le produit est à usage commercial ou collectif. Cette garantie ne couvre pas (a) les produits qui ont été endommagés par des calamités naturelles, de la
négligence, une mauvaise utilisation ou par accident, ou qui ont été modifiés ou réparés par des personnes non autorisées; (b) le coût de la main-d'oeuvre; ou le coût de
l'envoi du produit, de toute pièce ou de tout produit ou pièce de rechange.
Swing-N-Slide® RENONCE À TOUTES AUTRES REPRÉSENTATIONS ET GARANTIES DE TOUTES SORTES, EXPLICITES, IMPLICITES, RÉGLEMENTAIRES OU AUTRES, Y
COMPRIS LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE ET D'ADÉQUATION À UN USAGE PARTICULIER. Swing-N-Slide® N’EST PAS RESPONSABLE DES
DOMMAGES ACCESSOIRES OU INDIRECTS. Cette garantie n'est pas cessible, ni transférable à un propriétaire subséquent. Certains États interdisent les limitations sur les
garanties implicites ou l'exclusion de dommages accessoires ou indirects, il est donc possible que ces restrictions ne s'appliquent pas dans le cas présent. Cette garantie
vous donne des droits juridiques spécifiques. Vous pouvez également disposer d'autres droits, qui peuvent varier d'un État à l'autre.
De plus, cette garantie ne s'applique pas à :
• Des structures qui ne sont pas érigées, entretenues ou inspectées conformément aux plans d'installation de Swing-N-Slide®;
• Des structures auxquelles des pièces, ne respectant pas les plans d'installation de Swing-N-Slide®, ont été ajoutées ou substituées;
• Des pièces qui ont été modifiées ou mal utilisées;
• Des pièces qui n'ont pas été utilisées à des fins pour lesquelles elles ont été conçues;
• Des dommages dus à des calamités naturelles, au vandalisme, à un usage anormal ou abusif tel qu'établi par Swing-N-Slide®.
%=C@23>:CA/;>:3A@3<A375<3;3<BAAC@:/AN1C@7BN23AB3@@/7<A2383C télécharger gratuitement le manuel «
Handbook for Public Playground Safety]» de la commission de la sécurité des produits de consommation (CPSC) qui se
trouve à l'adresse EEE1>A15=D. Une ressource supplémentaire est offerte par
la spécification sur le rendement en matière de la sécurité des consommateurs des terrains de jeux résidentiels (ASTM
F1148) de l'American Society of Testing and Materials (ASTM - société américaine pour les essais et les matériaux), que
l'on peut acheter ou télécharger de EEE/AB;=@5.
5
4
Lista de control de seguridad para los juegos y accesorios Swing-N-Slide
I
Installation sécuritaire - Avez-vous :
Consulté les instructions d’assemblage fournies avec l’unité de jeu?
Noté que cet accessoire convient uniquement aux unités de jeu Swing•N•Slide approuvées? (ne modifiez pas sa composition et n'ajoutez ni ne retirez de composantes);
Vérifié que toute la quincaillerie est solidement fixée en place? (les capuchons protecteurs de boulons fournis doivent également être solidement fixés);
Utilisé une scie à métaux pour couper les extrémités des boulons ou autres fixations qui dépassent, limé tous les bords tranchants avec une lime métallique et recouvert
l'extrémité des attaches avec de la peinture sans plomb?
Placé l’équipement sur une surface plane et de niveau à une distance d’au moins 6 pieds (1,8 m) de toute structure ou de tout objet, comme une clôture, un garage, une maison,
des branches d’arbre surplombantes, une corde à linge ou des fils électriques?
Vérifié que l’équipement de jeu n’est pas installé sur un sol en béton, en asphalte, en terre compactée ni sur toute autre surface dure? (une chute sur une surface dure peut
entraîner de sérieuses blessures à l'utilisateur de cet équipement);
Vérifié que les cordes d'escalade suspendues, les chaînes ou câbles sont solidement ancrés aux deux bouts et ne peuvent pas s'enrouler sur eux-mêmes?
Consulté les directives d’assemblage du modèle afin de connaître les zones d’utilisation minimales?
Utilisé un scellant hydrofuge pour protéger le bois et prévenir l'apparition de fissures et de déformation sur votre ensemble de jeu?
Respecté toutes les exigences d’ancrage et de recouvrement amortissant pertinentes qui figurent au verso de cette feuille?
Interdit aux enfants d’utiliser l’équipement tant que l’assemblage n’est pas complètement terminé?
Veillé à ajuster toutes les balançoires, afin qu'il y ait une distance minimum de 8 po (200 mm) entre la balançoire et la surface du sol?
Précautions d’utilisation – Vous devez :
Assurer qu’un adulte est présent pour surveiller les enfants de tous âges.
Aviser les enfants de respecter les consignes qui suivent avant de leur permettre d’utiliser l’équipement.
Ne pas marcher près ni en face des éléments mobiles, ni derrière ceux-ci.
Ne pas tordre la balançoire ou toute autre chaîne et corde accessoires et ne pas les entortiller sur la barre de soutien supérieure, car cela réduirait la résistance de la chaîne
ou de la corde.
Ne pas balancer les sièges de balançoire ou d'autres accessoires lorsqu'ils sont vides.
Ne pas glisser le long des chaînes de la balançoire.
Vous assurer d'être assis bien au centre du siège de la balançoire et des autres accessoires avec votre poids entier sur le siège.
Ne pas attacher d’objets sur l’équipement de jeu qui ne sont pas spécifiquement conçus pour cet équipement tels que, mais sans s'y limiter, cordes à sauter, cordes à linge,
laisses d’animaux, câbles et chaînes. Ils pourraient présenter des risques de strangulation.
Ne pas grimper ou marcher sur le dessus des poutres, des rampes ou du toit de la balançoire.
Veiller à ne pas utiliser l’équipement à des fins autres que celles prévues.
Ne pas descendre de l'équipement lorsqu'il est en mouvement.
Ne pas grimper sur l'équipement lorsqu'il est mouillé.
Veiller à descendre les pieds devant.
Vous assurer qu'un seul enfant à la fois, par siège, doit être permis sur cet équipement.
Déterminé que les enfants doivent être habillés convenablement pour jouer. Évitez les vestes à capuchon, casques de bicyclette ou d'autres sports, les vêtements avec des cordons
et les vêtements amples qui pourraient s'emmêler ou s'accrocher sur l'équipement.
Déterminé que les cordes d'escalade suspendues, les chaînes ou câbles sont solidement ancrés aux deux bouts et ne peuvent pas s'enrouler sur eux-mêmes.
Vous assurer que la glissoire est installée de façon à ne pas être exposée à un ensoleillement direct.
Entretien de sécurité – Suivez ces consignes d'entretien préventif aux intervalles de temps requis :
Pour empêcher la détérioration des matériaux, retirez les sièges de balançoire en plastique et les autres accessoires en plastique lorsque les températures extérieures descendent
jusqu'à ou en dessous de 0 °C (32 °F) et rentrez-les à l'intérieur. Réinstallez ces éléments en plastique au début de chaque saison de jeux à l'extérieur.
Au début de chaque saison de jeux à l'extérieur, inspectez les pièces métalliques à la recherche de rouille. Si vous trouvez des parties rouillées, poncez-les et repeignez-les avec
une peinture sans plomb conforme aux exigences de la norme 16 CFR 1303 ou SOR/2005-109.
Au début de chaque saison de jeux à l'extérieur et une fois par mois pendant chaque saison, inspectez les pièces mobiles à la recherche d'usure, de rouille ou toute autre
détérioration. Remplacez-les selon les besoins. Si une de ces conditions existe, appelez le 1 800 888-1232 pour commander les accessoires de rechange.
Au début de chaque saison de jeux à l'extérieur et une fois par mois pendant chaque saison, lubrifiez les pièces métalliques mobiles.
Au début de chaque saison de jeux à l'extérieur et deux fois par mois pendant chaque saison, inspectez toutes les protections couvrant les boulons, tuyaux, rebords et coins.
Remplacez-les si elles sont desserrées, fissurées ou manquantes.
Au début de chaque saison de jeux à l'extérieur et deux fois par mois pendant chaque saison, ratissez et vérifiez la profondeur du matériau particulaire de revêtement de protection
pour en prévenir le compactage et maintenir une profondeur appropriée. Remplacez si nécessaire.
Au début de chaque saison de jeux à l'extérieur et deux fois par mois pendant chaque saison, resserrez toutes les pièces de quincaillerie.
Au début de chaque saison de jeux à l'extérieur et deux fois par mois pendant chaque saison, inspectez tous les éléments en bois à la recherche de détérioration et d'échardes.
Poncez les échardes pour les éliminer et remplacez les éléments en bois détériorés.
Instructions pour la mise au rebut
Lorsque l’équipement est mis hors service, il doit être démonté et conditionné de sorte qu’aucun danger justifié ne sera présent lors de la mise
au rebut de l’ensemble.
Important! Instructions supplémentaires de sécurité pour tous les centres de jeu Swing-N-Slide. Conserver ce feuillet
d’instruction au cas où vous devriez prendre contact avec le fabricant.
L’observation des déclarations et des avertissements suivants réduit les risques de blessures graves ou mortelles
3
.=</23A35C@
72/2
23:B=0=5K<
.=<323AN1C@
7BN
23:/5:7AA=7@3
.=</23
A35C@72/223:/
D75/23:1=:C;>7=
.=<323AN1C@7BN
23:/>=CB@323:/
0/:/<M=7@3
.=</23
A35C@72/223:/
D75/23:1=:C;>7=
.=<323AN1C@7BN
23:/>=CB@323:/
0/:/<M=7@3
+75/23:
1=:C;>7=
%=CB@323:/
0/:/<M=7@3
.
=
<
/
2
3
A
3
5
C
@7
2
/
2
2
3
:
B
=
0
=
5
K
<
.
=
<
3
2
3
A
N
1
C
@7
B
N
2
3
:
/
5
:
7
A
A
=
7
@3
=:=1/17S<1=@@31B/23:B=0=5K<)C@0=)C033<:/B=@@3
;>:/13;3<B/>>@=>@7N23:/5:7AA=7@3)C@0=)C03AC@:/B=C@
.=</23A35C@
7
2/2
23:
B=0=5K<
.=<323AN1C@
7
BN
23:
/5:
7
AA=7
@
3
$>17S<
$>B7=<
$>17S<
$>B7=<
$>17S<$>B7=<
#$)
AB327/5@/;/3ABK
0/A/2=3<C</
>:/B/4=@;/1C/2@/2/
23
'"'&*W
!3A16N;/3AB4/7B
3<4=<1B7=<2ZC<3
>:/B34=@;31/@@N3
23WW>=
(^
$*
(^
$*
#$
#$#
2
.=</;Q
<7
;/23
A35C@72/
2
.=<3
23
AN1
C@7
BN
;7
<7
;/:
3
7;3<A7=<3A23:B=0=5K<)C@0=)C03
7;3<A7=<A23:/5:7AA=7@3)C@0=)C03
#()'*$#(#("!
#()'*)$#(Z(("!
#=B/Este accesorio está diseñado para colocarse en >:/B/4=@;/A23>73A23/:B=T<71/;3<B3.
'3;/@?C3WCet accessoire est conçu pour s’adapter à C<3>:/B34=@;36/CB323W>7A3C:3;3<B.
% ' * _ #
•
No trepar por el exterior del
tobogán
• Este tobogán está diseñado
para ser usado en casa, no
para sitios públicos de juego.
• Producto diseñado para
niños de 2 a 10 años.
Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545
Visite nuestro sitio Web en: www.swing-n-slide.com o llámenos al
Consultez notre site Internet à l’adresse suivante]: www.swing-n-slide.com ou téléphonez-nous au
%/@/@357AB@/@AC>@=2C1B=G23A1/@5/@:/A7<AB@C117=<3A3A>31Q471/A23:/C<72/2B=0=5K<)C@0=)C03D7A7B3
http://www.swing-n-slide.com
Se incluyen otros beneficios, como información sobre las garantías del producto, actualizaciones del plan de ensamblaje, unirse
a nuestra lista de correo para nuevos productos y promociones y proporcionar comentarios sobre los productos.
%=C@3<@357AB@3@D=B@3>@=2C7B3BBN:N16/@53@:3A7<AB@C1B7=<A>/@B71C:7O@3AL:/5:7AA=7@3)C@0=)C03D7A7B3H:3A7B3,30W
http://www.swing-n-slide.com
Vous y trouverez également des informations au sujet des garanties des produits, des mises à jour concernant les plans
d’assemblage, et vous pourrez également vous abonner à notre liste d’envoi afin de connaître les nouveaux produits et les
promotions que nous offrons et nous faire part de vos commentaires et suggestions concernant les produits.
V"%$')#)
¡LEA ANTES DE COMENZAR EL ENSAMBLAJE!
Asegúrese de que todas las piezas de madera, los herrajes y los accesorios estén incluidos. Si falta algo,
#$+*!+! )
a la tienda
donde lo compró. Llame a nuestro Departamento de Servicio al Cliente, al número que aparece abajo.
"%$')#)
VEUILLEZ LIRE AVANT DE COMMENCER L’ASSEMBLAGE!
Veuillez vous assurer d’avoir toutes les pièces de bois, de quincaillerie ainsi que tous les accessoires. S’il vous manque quoi que ce soit,
#')$*'#.%(
l’article au magasin où vous l’avez acheté. Veuillez communiquer avec notre service à la clientèle en téléphonant au numéro ci-dessous.
© PlayCore Inc. 2013 Printed In USA LA 7035
Tobogán Turbo Tube de 5'
Glissoire Turbo Tube de 5 pi
!
WARNING:
Assembly by an adult.
!
ADVERTENCIA:
El ensamblaje lo
debe hacer un adulto.
!
AVERTISSEMENT:
L’assemblage doit être
exécuté par un adulte.
!
WARNING:
Assembly by an adult.
!
ADVERTENCIA:
El ensamblaje lo
debe hacer un adulto.
!
AVERTISSEMENT:
L’assemblage doit être
exécuté par un adulte.
" ( # '
•
Ne pas grimper sur l’extérieur
de la glissoire
• Cette glissoire est conçue
pour une utilisation
résidentielle seulement et
non pour être utilisée sur
des terrains de jeu publics.
• Ce produit est conçu pour
les enfants de 2 à 10*ans.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
Swing-N-Slide Playsets 6039 Instrucciones de operación
- Tipo
- Instrucciones de operación
- Este manual también es adecuado para
En otros idiomas
Documentos relacionados
-
Swing-N-Slide Playsets PB 9240S Instrucciones de operación
-
-
-
-
-
-
-
-
Swing-N-Slide Playsets NE 3052 Instrucciones de operación
-
Swing-N-Slide Playsets WS 5007 Instrucciones de operación
Otros documentos
-
Swing-N-Slide NE 4692-T Guía de instalación
-
Lifetime 90918 El manual del propietario
-
-
-
Lifetime 90136 El manual del propietario
-
Lifetime 90612 El manual del propietario
-
-
-
-