Alliance Laundry Systems HC50BN2 Manual de usuario

Marca: Alliance Laundry Systems

Modelo: HC50BN2

Categoría: Lavadoras

Tipo: Manual de usuario

Installation

www.comlaundry.com

Washer-Extractors

Cabinet Hardmount

Refer to Page 5 for Model Identification

CHM166C

NOTA: El manual en

español aparece después

del manual en inglés.

Part No. F232135R6

June 2005

Keep These Instructions for Future Reference.

(If this machine changes ownership, this manual must accompany machine.)

means without the expressed written consent of the publisher.

F232135

Table of

Contents

Safety Information.............................................................................. 3

Explanation of Safety Messages........................................................... 3

Important Safety Instructions ............................................................... 3

Introduction......................................................................................... 5

Model Identification ............................................................................. 5

Delivery Inspection............................................................................... 6

Nameplate Location.............................................................................. 6

Replacement Parts ................................................................................ 8

Customer Service.................................................................................. 8

Remove After Shipment (OPL Models Only)...................................... 8

Specifications and Dimensions........................................................... 9

Gap Setting for Vibration Switch

(Variable-Speed and Fixed-Speed Models) ................................... 12

Installation........................................................................................... 23

Dimensional Clearances ....................................................................... 23

Machine Foundation ............................................................................. 24

Machine Anchoring .............................................................................. 27

Direct-to-Finished-Floor Installation............................................... 27

Mounting Bolt Template Part Numbers

(Without Elevated Base Frame) ......................................................... 30

Mounting Bolt Hole Locations (Without Elevated Base Frames)........ 31

Mounting Bolt Hole Locations (Without Elevated Base Frames)........ 32

Mounting Bolt Hole Locations (With Elevated Base Frames)............. 33

Mounting Bolt Hole Locations (With Elevated Base Frames)............. 34

Elevated Base Frame Installation..................................................... 35

Concrete Foundation Installation..................................................... 37

Drain Connection.................................................................................. 40

Water Connection Requirements.......................................................... 42

Electrical Installation Requirements..................................................... 43

Input Voltage Requirements ............................................................ 43

Circuit Breakers ............................................................................... 43

Connection Specifications ............................................................... 44

Grounding ........................................................................................ 44

Phase Adder ..................................................................................... 44

Thermal Overload Protector ............................................................ 44

Troubleshooting ............................................................................... 50

Steam Requirements (Steam Heat Option Only).................................. 50

Supply Dispensing (OPL Machines Only) ........................................... 51

Connection of External Liquid Supplies.......................................... 51

Control Function Test........................................................................... 54

F232135

Notes

F232135

Safety Information

Explanation of Safety Messages

Precautionary statements (“DANGER,” “WARNING,”

and “CAUTION”), followed by specific instructions,

are found in this manual and on machine decals. These

precautions are intended for the personal safety of the

operator, user, servicer, and those maintaining the

machine.

Additional precautionary statements (“IMPORTANT”

and “NOTE”) are followed by specific instructions.

IMPORTANT: The word “IMPORTANT” is used

to inform the reader of specific procedures where

minor machine damage will occur if the procedure

is not followed.

NOTE: The word “NOTE” is used to communicate

installation, operation, maintenance or servicing

information that is important but not hazard

related.

Important Safety Instructions

1. Read all instructions before using the washer.

2. Refer to the GROUNDING INSTRUCTIONS in

the INSTALLATION manual for the proper

grounding of the washer.

3. Do not wash textiles that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, kerosene, waxes, cooking oils, dry-

cleaning solvents, or other flammable or

explosive substances as they give off vapors that

could ignite or explode.

4. Do not add gasoline, dry-cleaning solvents, or

other flammable or explosive substances to the

wash water. These substances give off vapors that

could ignite or explode.

5. Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for two weeks or more. HYDROGEN GAS

IS EXPLOSIVE. If the hot water system has not

been used for such a period, before using a

washing machine or combination washer-dryer,

turn on all hot water faucets and let the water

flow from each for several minutes. This will

release any accumulated hydrogen gas. The gas is

flammable, do not smoke or use an open flame

during this time.

6. Do not allow children to play on or in the washer.

Close supervision of children is necessary when

the washer is used near children. This is a safety

rule for all appliances.

7. Before the washer is removed from service or

discarded, remove the door to the washing

compartment.

8. Do not reach into the washer if the wash drum is

moving.

DANGER indicates the presence of a

hazard that will cause severe personal

injury, death, or substantial property

damage if the danger is ignored.

DANGER

WARNING indicates the presence of a

hazard that can cause severe personal

injury, death, or substantial property

damage if the warning is ignored.

WARNING

CAUTION indicates the presence of a

hazard that will or can cause minor

personal injury or property damage if the

caution is ignored.

CAUTION

To reduce the risk of fire, electric shock,

serious injury or death to persons when

using your washer, follow these basic

precautions:

W023

WARNING

Safety Information

F232135

9. Do not install or store the washer where it will be

exposed to water and/or weather.

10. Do not tamper with the controls.

11. Do not repair or replace any part of the washer, or

attempt any servicing unless specifically

recommended in the user-maintenance

instructions or in published user-repair

instructions that the user understands and has the

skills to carry out.

12. To reduce the risk of an electric shock or fire, DO

NOT use an extension cord or an adapter to

connect the washer to the electrical power source.

13. Use washer only for its intended purpose,

washing textiles.

14. ALWAYS disconnect the washer from electrical

supply before attempting any service. Disconnect

the power cord by grasping the plug, not the cord.

15. Install the washer according to the

INSTALLATION INSTRUCTIONS. All

connections for water, drain, electrical power and

grounding must comply with local codes and be

made by licensed personnel when required.

16. To reduce the risk of fire, textiles which have

traces of any flammable substances such as

vegetable oil, cooking oil, machine oil,

flammable chemicals, thinner, etc., or anything

containing wax or chemicals such as in mops and

cleaning cloths, must not be put into the washer.

These flammable substances may cause the

fabric to catch on fire by itself.

17. Do not use fabric softeners or products to

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

18. Keep washer in good condition. Bumping or

dropping the washer can damage safety features.

If this occurs, have washer checked by a qualified

service person.

19. Replace worn power cords and/or loose plugs.

20. Be sure water connections have a shut-off valve

and that fill hose connections are tight. CLOSE

the shut-off valves at the end of each wash day.

21. Loading door MUST BE CLOSED any time the

washer is to fill, tumble or spin. DO NOT

bypass the loading door switch by permitting the

washer to operate with the loading door open.

22. Always read and follow manufacturer’s

instructions on packages of laundry and cleaning

aids. Heed all warnings or precautions. To reduce

the risk of poisoning or chemical burns, keep

them out of the reach of children at all times

(preferably in a locked cabinet).

23. Always follow the fabric care instructions

supplied by the textile manufacturer.

24. Never operate the washer with any guards and/or

panels removed.

25. DO NOT operate the washer with missing or

broken parts.

26. DO NOT bypass any safety devices.

27. Failure to install, maintain, and/or operate this

washer according to the manufacturer’s

instructions may result in conditions which can

produce bodily injury and/or property damage.

NOTE: Underloading can cause out-of-balance

conditions that can shorten life of machine.

NOTE: The WARNINGS and IMPORTANT

SAFETY INSTRUCTIONS appearing in this

manual are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining, or operating the washer.

Any problems or conditions not understood should be

reported to the dealer, distributor, service agent or the

manufacturer.

F232135

Introduction

Model Identification

Information in this manual is applicable to these

models:

HC18MD2 HC25NR2 HC35SN2 HC60ACV HC80NRV SC25MD2 SC40AY2 SC60BNF UC20VN2

HC18MN2 HC25NX2 HC35VC2 HC60AL2 HC80NXV SC25ML2 SC40BC2 SC60BX2 UC25MN2

HC18MX2 HC25SN2 HC35VX2 HC60ALF HC80VCV SC25MN2 SC40BL2 SC60BXF UC27MN2

HC18NC2 HC25VC2 HC40AC2 HC60ALV HC80VNV SC25MX2 SC40BN2 SC60BY2 UC27PN2

HC18NR2 HC25VX2 HC40ACV HC60AX2 HC80VXV SC25MY2 SC40BX2 SC60BYF UC27VN2

HC18NX2 HC27MD2 HC40AL2 HC60AXF HC125BYV SC25NC2 SC40BY2 SC60MD2 UC27VNV

HC18SN2 HC27MN2 HC40ALV HC60AXV NC18NP2 SC25NR2 SC40MD2 SC60ML2 UC30BN2

HC18VC2 HC27MX2 HC40AX2 HC60AY2 NC27NP2 SC25NX2 SC40ML2 SC60MN2 UC30ML2

HC18VX2 HC27NC2 HC40AXV HC60AYF NC80NPV SC27MD2 SC40MN2 SC60MX2 UC30MN2

HC20AC2 HC27NR2 HC40AY2 HC60AYV SC125BYV SC27MN2 SC40MX2 SC60MY2 UC30MX2

HC20ACV HC27NX2 HC40AYV HC60BC2 SC125VNV SC27MX2 SC40MY2 SC60NC2 UC30PN2

HC20AL2 HC27SN2 HC40BC2 HC60BCF SC18MD2 SC27NC2 SC40NC2 SC60NCF UC30VN2

HC20ALV HC27VC2 HC40BL2 HC60BL2 SC18MN2 SC27NR2 SC40NR2 SC60NR2 UC35MD2

HC20AX2 HC27VX2 HC40BN2 HC60BLF SC18MX2 SC27NX2 SC40NX2 SC60NX2 UC35MN2

HC20AXV HC30AC2 HC40BX2 HC60BN2 SC18NC2 SC27VN2 SC40VN2 SC60NXF UC35PN2

HC20AY2 HC30ACV HC40BY2 HC60BNF SC18NR2 SC30AC2 SC40VNV SC60VN2 UC35VN2

HC20AYV HC30AL2 HC40MD2 HC60BX2 SC18NX2 SC30AL2 SC50BC2 SC60VNF UC35VNV

HC20BC2 HC30ALV HC40ML2 HC60BXF SC18VN2 SC30AY2 SC50BL2 SC60VNV UC40BN2

HC20BL2 HC30AX2 HC40MN2 HC60BY2 SC20AC2 SC30AX2 SC50BN2 SC80ACV UC40MN2

HC20BN2 HC30AXV HC40MX2 HC60BYF SC20AL2 SC30BC2 SC50BX2 SC80ALV UC40PN2

HC20BX2 HC30AY2 HC40MY2 HC60MD2 SC20AX2 SC30BL2 SC50BY2 SC80AXV UC40VN2

HC20BY2 HC30AYV HC40NC2 HC60ML2 SC20AY2 SC30BN2 SC50MD2 SC80AYV UC40VNV

HC20MD2 HC30BC2 HC40NR2 HC60MN2 SC20BC2 SC30BX2 SC50ML2 SC80BCV UC50BN2

HC20ML2 HC30BL2 HC40NX2 HC60MX2 SC20BL2 SC30BY2 SC50MN2 SC80BLV UC50MN2

HC20MN2 HC30BN2 HC40SN2 HC60MY2 SC20BN2 SC30MD2 SC50MX2 SC80BNV UC50PN2

HC20MX2 HC30BX2 HC40VC2 HC60NC2 SC20BX2 SC30ML2 SC50MY2 SC80BXV UC50VN2

HC20MY2 HC30BY2 HC40VX2 HC60NCF SC20BY2 SC30MN2 SC50NC2 SC80BYV UC50VNV

HC20SN2 HC30MD2 HC50BC2 HC60NR2 SC20MD2 SC30MX2 SC50NR2 SC80NCV UC60BN2

HC20VC2 HC30ML2 HC50BL2 HC60NX2 SC20ML2 SC30MY2 SC50NX2 SC80NRV UC60BNF

HC20VX2 HC30MN2 HC50BN2 HC60PN2 SC20MN2 SC30NC2 SC50VN2 SC80NXV UC60MN2

HC25AC2 HC30MX2 HC50BX2 HC60SN2 SC20MX2 SC30NR2 SC50VNV SC80NYV UC60PN2

HC25AL2 HC30MY2 HC50BY2 HC60VC2 SC20MY2 SC30NX2 SC60AC2 SC80VNV UC60VN2

HC25AX2 HC30NC2 HC50MD2 HC60VX2 SC20NC2 SC30VN2 SC60ACF UC125VNV UC60VNF

HC25AY2 HC30NR2 HC50ML2 HC80ACV SC20NR2 SC35MD2 SC60AL2 UC18MN2 UC60VNV

HC25BC2 HC30NX2 HC50MN2 HC80ALV SC20NX2 SC35MN2 SC60ALF UC18MX2 UC80BNV

HC25BL2 HC30SN2 HC50MX2 HC80AXV SC20VN2 SC35MX2 SC60AX2 UC18PN2 UC80VNV

HC25BX2 HC30VC2 HC50MY2 HC80AYV SC25AC2 SC35NC2 SC60AXF UC18VN2

HC25BY2 HC30VX2 HC50NC2 HC80BCV SC25AL2 SC35NR2 SC60AY2 UC18VNV

HC25MD2 HC35MD2 HC50NR2 HC80BLV SC25AX2 SC35NX2 SC60AYF UC20BN2

HC25ML2 HC35MN2 HC50NX2 HC80BNV SC25AY2 SC35VN2 SC60BC2 UC20MD2

HC25MN2 HC35MX2 HC50SN2 HC80BXV SC25BC2 SC35VNV SC60BCF UC20ML2

HC25MX2 HC35NC2 HC50VC2 HC80BYV SC25BL2 SC40AC2 SC60BL2 UC20MN2

HC25MY2 HC35NR2 HC50VX2 HC80NCF SC25BX2 SC40AL2 SC60BLF UC20MX2

HC25NC2 HC35NX2 HC60AC2 HC80NCV SC25BY2 SC40AX2 SC60BN2 UC20PN2

Introduction

F232135

This manual is designed as a guide to the installation

of the Cabinet Hardmount Washer-Extractor.

NOTE: All information, illustrations, and

specifications contained in this manual are based

on the latest product information available at the

time of printing. We reserve the right to make

changes at any time without notice.

Delivery Inspection

Upon delivery, visually inspect crate, protective cover,

and unit for any visible shipping damage. If the crate,

protective cover, or unit is damaged or signs of

possible damage are evident, have the carrier note the

condition on the shipping papers before the shipping

receipt is signed, or advise the carrier of the condition

as soon as it is discovered.

Remove the crate and protective cover as soon after

delivery as possible. If any damage is discovered upon

removal of the crate and/or protective cover, advise the

carrier and file a written claim immediately.

Nameplate Location

The nameplate is located at the rear of the machine and

inside door. Always provide the machine’s serial

number and model number when ordering parts or

when seeking technical assistance. Refer to Figure 1.

Figure 1

CHM167R

1 Nameplate

CHM167R

Introduction

F232135

* Denotes Brand

Figure 2

Model Number Familiarization Guide

Sample Model Number: *C40AC2OU60001

Model Number Prefix

Washer-Extractor Capacity (pounds dry weight of laundry)

Type of Electrical Control

Actuation (C = Coin drop)

Washer-Extractor Speed Capability (2 = 2 speed)

Electrical Characteristics

Design Series

0001

Option Identification (varies from machine to machine)

CHM2008N

*C40AC2OU60001

00000000000

500000

208 – 240

60 3 3

N/A N/A

470

EXAMPLE OF NAMEPLATE

Introduction

F232135

Replacement Parts

If literature or replacement parts are required, contact

the source from which the machine was purchased or

contact Alliance Laundry Systems at (920) 748-3950

for the name and address of the nearest authorized

parts distributor.

Customer Service

For technical assistance, call (920) 748-3121, Ripon,

Wisconsin U.S.A.

Remove After Shipment (OPL

Models Only)

A yellow retainer has been inserted in the door locks

of all cabinet hardmount on-premise laundry washer-

extractors to prevent the door from locking during

shipment. Remove the yellow retainer during

installation by pulling it off.

NOTE: Once retainer is removed, machine must be

powered to unlock door.

A tag has been attached to the washer-extractor’s door

handle as a reminder that the retainer must be removed

before operation. Refer to Figure 3.

Figure 3

CFS503N

Remove Yellow Retainer

Before Starting Machine.

Note: A Retainer has been

inserted to prevent the door from

locking during shipment.

F232135

Specifications and Dimensions

2 Speed Models

Specification 18, 20 25 27, 30 35 40 50 60

Overall Dimensions

Overall width, in. (mm) 26

(660)

(737)

30-1/8

(765)

30-5/8

(778)

34-1/16

(865)

34-1/16

(865)

Overall height, in. (mm) 42-7/8

(1089)

(1143)

45-7/8

(1165)

47-1/4

(1200)

47-7/8

(1216)

50-13/16

(1291)

50-13/16

(1291)

Overall depth, in. (mm) 29-13/16

(757)

33-7/8

(860)

34-13/16

(884)

38-1/2

(978)

40-3/16

(1021)

41-13/16

(1087)

42-13/16

(1087)

Weight and Shipping Information

Net weight, lbs. (kg) 390

(177)

435

(198)

498

(226)

650

(295)

706

(321)

820

(373)

826

(375)

Domestic shipping weight,

lbs. (kg)

428

(194)

470

(214)

545

(245)

680

(309)

744

(338)

875

(398)

881

(400)

Domestic shipping

volume, ft

)

(0.8)

(0.9)

(1.0)

(1.09)

42.6

(1.19)

(1.5)

Export shipping weight

lbs. (kg)

480

(218)

530

(241)

588

(267)

760

(345)

846

(385)

1020

(464)

1027

(466)

Export shipping volume,

)

30.1

(0.86)

36.7

(1.03)

39.6

(1.11)

47.1

(1.32)

54.1

(1.51)

58.7

(1.67)

58.7

(1.67)

Wash Cylinder Information

Cylinder diameter,

in. (mm)

(533)

(610)

26-1/4

(667)

26-1/4

(667)

(762)

Cylinder depth, in. (mm) 13-3/4

(349)

18-3/4

(476)

(406)

18-3/8

(467)

20-1/4

(514)

(508)

(559)

Cylinder volume, ft

(l) 2.76

(78.1)

3.76

(106.5)

4.19

(118.6)

5.76

(163.1)

6.34

(180)

8.18

(231.6)

9.00

(255)

Perforation size, in. (mm) 0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

Perforation open area, % 17 17 23 17 17.5 18 18

Specifications and Dimensions

F232135

2 Speed Models (Continued)

Specification 18, 20 25 27, 30 35 40 50 60

Door Opening Information

Door opening diameter,

in. (mm)

(305)

14-11/32

(364)

14-11/32

(364)

16-1/4

(413)

16-1/4

(413)

16-1/4

(413)

Height of door bottom above

floor, in. (mm)

14-3/8

(365)

14-3/8

(365)

(356)

(406)

14-1/2

(368)

13-1/2

(343)

13-1/2

(343)

Power Consumption

Average power used per cycle,

kW-hr

0.20 0.25 0.25 0.30 0.34 0.42 0.61

Average HVAC load, Btu/hr 425 400 400 510 510 700 700

Drive Train Information

Number of motors in drive

train

1111111

Wash/reverse power, HP (kW) 0.18

(0.13)

0.25

(0.19)

0.25

(0.19)

0.40

(0.30)

0.40

(0.30)

0.55

(0.41)

0.55

(0.41)

High extract power, HP (kW) 1.0

(0.746)

1.4

(1.04)

1.4

(1.04)

1.8

(1.3)

1.8

(1.3)

2.7

(2.01)

2.7

(2.01)

Cylinder Speeds

Wash/reverse speed, RPM53554747474444

High extract speed, RPM 525 540 480 470 470 450 450

Centrifugal Force Data

Wash/reverse centrifugal

force, Gs

0.85 0.90 0.75 0.82 0.82 0.825 0.825

High extract centrifugal force,

82.1 86.8 78.4 82.3 82.3 86.3 86.3

Specifications and Dimensions

F232135

2 Speed Models (Continued)

Specification 18/20 25 27, 30 35 40 50 60

Balance Detection

Vibration switch installed N/A N/A N/A N/A N/A N/A N/A

Direct Steam Heating (Optional)

Steam inlet connection size,

in. (mm)

1/2

(13)

1/2

(13)

1/2

(13)

1/2

(13)

1/2

(13)

1/2

(13)

1/2

(13)

Number of steam inlets 1111111

Steam required to raise

bath water temperature

°F (6°C)

LOW 1.05 (0.75) 1.4 (1.01) 1.44 (1.03) 2.06 (1.48) 2.09 (1.51) 2.76 (1.99) 2.76 (1.99)

HIGH 1.4 (1.01) 1.59 (1.15) 1.91 (1.37) 2.69 (1.94) 2.84 (2.04) 3.59 (2.59) 3.59 (2.59)

Average steam use per cycle,

bhp (kg)

0.71

(11.1)

0.87

(13.6)

0.97

(15.2)

1.4

(21.6)

1.43

(22.4)

1.84

(28.9)

1.84

(28.9)

Electrical Heating (Optional)

Total electrical heating capacity,

7.8 7.8 7.8 15.6 15.6 23.4 23.4

Electrical heating elements 3336399

Electrical heat element size, kW 2.6 2.6 2.6 2.6 5.2 2.6 2.6

Specifications and Dimensions

F232135

Gap Setting for Vibration Switch (Variable-

Speed and Fixed-Speed Models)

After the machine has been properly installed, the

vibration switch gap must be measured before

conducting the Control Function Test. Locate the gap

found between the vibration switch and the machine

structure. Refer to Figures 4, 5, 6, 7 and 8. To check

the gap setting of the switch, proceed as follows:

1. Remove the front panel on 18-50 models.

Remove the rear panel on 60-80 models. Remove

the top cover on the 125 model. The switch can

be seen inside the bottom right corner of the A-

frame, mounted on a bracket. Refer to Figures 4,

5, 6, 7 and 8.

2. Measure the gap distance when the switch is in

both the open and closed positions. The

specifications should be at the minimum switch

gap setting when the switch is open and at the

maximum switch gap setting when the switch is

closed. If these distances are not correct, adjust

the balance switch to these specifications.

NOTE: The standard position of the switch is open,

or non-tripped.

3. Tighten nuts on switch extension after adjusting

the gap. Measure the gap distance to verify

accurate setting.

18, 20 27, 30 35 40 50 60 80 125

Switch gap setting*,

in. (mm)

0.015-0.025

(0.38-0.64)

0.025-0.035

(0.64-0.89)

0.030-0.040

(0.76-1.02)

0.020-0.030

(0.51-0.64)

0.025-0.035

(0.64-0.89)

0.013-0.015

(0.20-0.25)

0.009-0.011

(0.23-0.28)

0.006-0.008

(0.15-0.20)

* Gap setting should be made with “GO-NO-GO” type feeler gauge. Lower value must not trip switch. Upper value must trip switch.

Table 1

Specifications and Dimensions

F232135

For 18, 20, 25, 27, 30 and 35 Pound

Capacity Machines

Figure 4

CHM1995N

1 Sump 3 Vibration Switch

2 Gap Distance 4 Switch Extension

CHM1995N

Specifications and Dimensions

F232135

For 40 and 50 Pound Capacity Variable-Speed

and Fixed-Speed Machines

Figure 5

CHM2000N

1 Sump 3 Vibration Switch

2 Gap Distance 4 Switch Extension

Specifications and Dimensions

F232135

For 60 Pound Capacity Variable-Speed and

Fixed-Speed Machines

Figure 6

CHM1999N

1 Lower Bracket 4 Balance Bolt

2 Upper Bracket 5 Lock Nut

3 Vibration Switch 6 Gap Distance

CHM1999N

Specifications and Dimensions

F232135

For 80 Pound Capacity Machines

Figure 7

CHM1998N

1 Switch Extension 3 Vibration Switch

2 Gap Distance

CAB1998N

Specifications and Dimensions

F232135

For 125 Pound Capacity Machines

Figure 8

CHM1993N

1 Vibration Switch 3 Switch Extension

2 Gap Distance

Specifications and Dimensions

F232135

Variable-Speed and Fixed-Speed Models

Specification 20 30 35 40 50 60 80 125

Overall Dimensions

Overall width, in. (mm) 26

(660)

(737)

30-1/8

(765)

30-5/8

(778)

34-1/16

(865)

34-1/16

(865)

41-1/2

(1054)

(1219)

Overall height, in. (mm) 42-7/8

(1089)

45-7/8

(1165)

47-1/4

(1200)

47-7/8

(1216)

50-13/16

(1291)

50-13/16

(1291)

(1422)

70-1/2

(1791)

Overall depth, in. (mm) 29-13/16

(757)

34-13/16

(884)

38-1/2

(978)

40-3/16

(1021)

42-13/16

(1087)

42-13/16

(1087)

51-5/8

(1311)

56-3/4

(1441)

Weight and Shipping Information

Net weight, lbs. (kg) 386

(175)

498

(226)

621

(282)

706

(321)

767

(348)

773

(350)

1406

(633)

2346

(1066)

Domestic shipping weight, lbs. (kg) 424

(191)

545

(245)

670

(301)

744

(338)

818

(371)

824

(373)

1456

(655)

2421

(1098)

Domestic shipping volume, ft

)28

(0.8)

(1.0)

(1.09)

42.6

(1.19)

(1.5)

(2.7)

153

(4.3)

Export shipping weight, lbs. (kg) 476

(215)

588

(267)

731

(332)

846

(385)

967

(439)

1020

(463)

1506

(678)

2701

(1225)

Export shipping volume, ft

)30.1

(0.86)

39.6

(1.11)

47.1

(1.32)

54.1

(1.51)

58.7

(1.67)

58.7

(1.67)

109.5

(3.1)

173

(4.8)

Wash Cylinder Information

Cylinder diameter, in. (mm) 21

(533)

(610)

26-1/4

(667)

26-1/4

(667)

(762)

(914)

(1060)

Cylinder depth, in. (mm) 13-3/4

(349)

(406)

18-3/8

(467)

20-1/4

(514)

(508)

(559)

(609)

Cylinder volume, ft

(l) 2.76

(78.1)

4.19

(118)

5.76

(163.1)

6.34

(180)

8.18

(232)

9.00

(255)

12.96

(367)

19.24

(545)

Perforation size, in. (mm) 0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

0.188

(4.76)

Perforation open area, % 17231717.518182717

Door Opening Information

Door opening size, in. (mm) 12

(305)

14-11/32

(364)

14-11/32

(364)

16-1/4

(413)

16-1/4

(413)

16-1/4

(413)

18-1/2

(470)

(508)

Height of door bottom above floor, in. (mm) 14-3/8

(365)

(356)

(406)

14-1/2

(368)

13-1/2

(343)

13-1/2

(343)

17-3/4

(451)

(737)

Power Consumption

Average power used per cycle, kW-hr 0.05 0.07 0.20 0.34 0.37 0.21 0.40 0.60

Average HVAC load, Btu/hr 400 450 510 510 750 750 950 1200

Specifications and Dimensions

F232135

* Refer to Gap Setting for Vibration Switch (Variable-Speed and

Fixed-Speed Models) section for specifications.

Drive Train Information

Number of motors in drive train 11111111

Drive motor power, HP (kW) 2

(1.5)

(2.2)

(3.7)

7.5

(5.6)

Cylinder Speeds

Gentle wash/reverse speed, RPM 2927262624242227

Wash/reverse speed, RPM 5248464743434037

Distribution speed, RPM 8286737368776362

Low extract speed, RPM 366 343 328 328 307 307 280 260

Medium extract speed, RPM

(Not available on Electronic Control models.)

534 500 478 478 447 447 408 380

High extract speed, RPM 685 641 613 614 573 574 524 485

Centrifugal Force Data

Gentle wash centrifugal force, Gs 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.43

Wash/reverse centrifugal force, Gs 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8

Distribution centrifugal force, Gs 22222222

Low extract centrifugal force, Gs 40 40 40 40 40 40 40 40

Medium extract centrifugal force, Gs 85 85 85 85 85 85 85 85

High extract centrifugal force, Gs 140 140 140 140 140 140 140 140

Balance Detection

Vibration switch installed* Standard Standard Standard Standard Standard Standard Standard Standard

Direct Steam Heating (Optional)

Steam inlet connection size,

in. (mm)

1/2

(13)

1/2

(13)

1/2

(13)

1/2

(13)

1/2

(13)

1/2

(13)

1/2

(13)

3/4

(19)

Number of steam inlets 11111111

Steam required to raise bath water

temperature 10°F (6°C), lbs. (kg)

LOW 0.62

(0.28)

0.92

(0.42)

2.1

(1.51)

2.09

(1.51)

2.8

(2.0)

3.6

(1.63)

4.1

(2.93)

6.8

(4.9)

HIGH 0.88

(0.4)

1.31

(0.6)

2.69

(1.96)

2.84

(2.04)

3.6

(2.59)

5.5

(2.49)

6.0

(4.34)

8.9

(6.4)

Average steam use per cycle, bhp (kg) 0.54

(8.3)

0.73

(11.3)

1.4

(21.6)

1.43

(22.4)

1.8

(28.9)

2.32

(36.4)

2.93

(45.9)

4.5

(71)

Electrical Heating (Optional)

Total electrical heating capacity, kW 7.8 7.8 15.6

15.6

23.4 23.4 31.2 N/A

Electrical heating elements 33639912N/A

Electrical heat element size, kW 2.6 2.6 2.6 5.2 2.6 2.6 2.6 N/A

Variable-Speed and Fixed-Speed Models (Continued)

Specification 20 30 35 40 50 60 80 125

Specifications and Dimensions

F232135

Figure 9

CHM2019N

1 Supply Dispenser 5 Hot Water Inlet

2 Input Power Block 6 Extra Inlet Valve

3 External Chemical Supply Signal Terminal Strip

(OPL only)

7 External Chemical Supply Inlet (OPL only)

8 Vacuum Breaker

4 Cold Water Inlet 9 Drain Outlet

CHM2019N

18, 20, 25, 27, 30, 35, 40, 50, 60 AND 80 POUND CAPACITY MACHINES

Specifications and Dimensions

F232135

Machine Capacity Dimensions

Dimensions 18, 20 25 27, 30 35 40 50 60 80

22-15/16

in.

(583 mm)

23 in.

(584 mm)

24 in.

(610 mm)

26 in.

(660 mm)

25-3/4 in.

(654 mm)

26-3/8 in.

(670 mm)

26-3/8 in.

(670 mm)

30-5/8 in.

(777 mm)

17-1/4

in.

(438 mm)

17-1/4 in.

(438 mm)

17 in.

(432 mm)

19 in.

(483 mm)

18 in.

(457 mm)

18-1/4 in.

(464 mm)

18-1/4

in.

(464 mm)

21-5/8

in.

(549 mm)

14-3/8

in.

(365 mm)

14-3/8 in.

(365 mm)

14 in.

(356 mm)

16 in.

(406 mm)

14-1/2 in.

(368 mm)

13-1/2 in.

(343 mm)

13-1/2 in.

(343 mm)

17-3/4 in.

(451 mm)

in.

(660 mm)

26 in.

(660 mm)

29 in.

(737 mm)

30-1/8 in.

(765 mm)

30-5/8 in.

(778 mm)

34-1/16 in.

(865 mm)

34-1/16 in.

(865 mm)

41-1/2 in.

(1054 mm)

25-5/8

in.

(650 mm)

30 in.

(762 mm)

30-5/8 in.

(775 mm)

34 in.

(864 mm)

36 in.

(914 mm)

37-3/4

in.

(959 mm)

38-3/4 in.

(984 mm)

48 in.

(1219 mm)

29-13/16

in.

(757 mm)

34-3/16 in.

(868 mm)

34-13/16 in.

(884 mm)

38-1/8 in.

(968 mm)

40-3/16 in.

(1021 mm)

41-13/16

in.

(1062 mm)

42-13/16 in.

(1087 mm)

in.

(1295 mm)

0001-1/8

in.

(29 mm)

1/2 in.

(13 mm)

1/2 in.

(13 mm)

1/2 in.

(13 mm)

1/2 in.

(13 mm)

in.

(1062 mm)

45 in.

(1143 mm)

45 in.

(1143 mm)

47 in.

(1194 mm)

47 in.

(1194 mm)

49-15/16 in.

(1268 mm)

49-15/16 in.

(1268 mm)

56 in.

(1422 mm)

12-1/2

in.

(318 mm)

12-1/2

in.

(318 mm)

15-1/4

in.

(387 mm)

14-1/4 in.

(362 mm)

15-7/16 in.

(392 mm)

20-3/4 in.

(527 mm)

20-3/4 in.

(527 mm)

22-1/4 in.

(572 mm)

11-1/2

in.

(292 mm)

11-1/2 in.

(292 mm)

14-3/4 in.

(375 mm)

10-13/16

in.

(275 mm)

14-7/16 in.

(367 mm)

19-3/4

in.

(502 mm)

19-3/4 in.

(502 mm)

14-7/16 in.

(378 mm)

3-1/2

in.

(89 mm)

3-1/2 in.

(89 mm)

3-3/4 in.

(95 mm)

2-3/4

in.

(70 mm)

3-13/16 in.

(97 mm)

3-1/2 in.

(89 mm)

3-1/2 in.

(89 mm)

3-7/16 in.

(87 mm)

34-1/2

in.

(876 mm)

37-1/2 in.

(952 mm)

37-11/16

in.

(957 mm)

40-1/8

in.

(1020 mm)

39 in.

(990 mm)

41-1/2 in.

(1054 mm)

41-1/2 in.

(1054 mm)

44-1/2 in.

(1130 mm)

5-3/4

in.

(146 mm)

5-3/4 in.

(146 mm)

5-7/8 in.

(149 mm)

7-5/16 in.

(186 mm)

5-1/2 in.

(140 mm)

6-7/16 in.

(163 mm)

6-7/16 in.

(163 mm)

6-3/8 in.

(162 mm)

4-1/2

in.

(114 mm)

4-1/2 in.

(114 mm)

4 in.

(102 mm)

4-3/4 in.

(121 mm)

4-3/4 in.

(121 mm)

5 in.

(127 mm)

in.

(127 mm)

5-3/4

in.

(146 mm)

in.

(51 mm)

2 in.

(51 mm)

2 in.

(51 mm)

in.

(51 mm)

3 in.

(76 mm)

in.

(76 mm)

3 in.

(76 mm)

3 in.

(76 mm)

36-3/16

in.

(919 mm)

39-3/16 in.

(995 mm)

38-15/16

in.

(989 mm)

41-15/16

in.

(1064 mm)

42-1/8 in.

(1070 mm)

43-3/16 in.

(1097 mm)

43-3/8 in.

(1102 mm)

42-3/4 in.

(1086 mm)

38-1/2 in.

(978 m)

41-1/2 in.

(1054 mm)

41 in.

(1041 mm)

41-15/16 in.

(1064 mm)

43-3/16 in.

(1097 mm)

45-1/2 in.

(1156 mm)

45-1/2 in.

(1156) mm)

50 in.

(1270 mm)

1-3/16 in.

(30 mm)

1-3/16 in.

(30 mm)

1-3/16 in.

(30 mm)

1-3/16 in.

(30 mm)

1-3/16 in.

(30 mm)

1-3/16 in.

(30 mm)

1-3/16 in.

(30 mm)

1-3/16 in.

(30 mm)

3 in.

(76 mm)

3 in.

(76 mm)

3 in.

(76 mm)

3 in.

(76 mm)

3 in.

(76 mm)

3 in.

(76 mm)

3 in.

(76 mm)

3 in.

(76 mm)

Specifications and Dimensions

F232135

B023I

1 Dry Chemical Dispenser

(Optional – OPL Models Only)

4 Hot Water Inlet

5 Liquid Chemical Inlet

2 Cold Water Inlet 6 Steam Inlet (Optional)

3 Extra Water Inlet (Optional) 7 Drain Outlet

B023I

125 POUND CAPACITY MACHINES

Machine Capacity Dimensions for 125 Pound Models

in. (1016 mm)

41 in. (1041 mm)

30-1/4

in. (768 mm)

38-1/2 in. (978 mm)

in. (737 mm)

33-1/2 in. (851 mm)

in. (203 mm)

29-3/4 in. (756 mm)

in. (1219 mm)

24 in. (610 mm)

50-1/2

in. (1283 mm)

13 in. (330 mm)

56-3/4

in. (1422 mm)

4-7/8 in. (124 mm)

in. (25 mm)

63-7/8 in. (1622 mm)

70-1/2

in. (1791 mm)

64-7/8 in. (1648 mm)

44-1/2

in. (1130 mm)

66-5/8 in. (1692 mm)

F232135

Installation

Dimensional Clearances

U158M

FRONT

Machine Capacity Dimensional Clearances

Dimensions 18, 20 25 27, 30 35 40 50 60 80 125

2 in.

(50 mm)

2 in.

(50 mm)

2 in.

(50 mm)

2 in.

(50 mm)

2 in.

(51 mm)

2 in.

(50 mm)

2 in.

(50 mm)

2 in.

(50 mm)

24 in.

(600 mm)

26 in.

(660 mm)

26 in.

(660 mm)

29 in.

(737 mm)

30-1/8 in.

(765 mm)

30-5/8 in.

(778 mm)

34-1/16 in.

(865 mm)

34-1/16 in.

(865 mm)

41-1/2 in.

(1054 mm)

48 in.

(1219 mm)

1 in.

(25 mm)

1 in.

(25 mm)

1 in.

(25 mm)

1 in.

(25 mm)

1 in.

(25 mm)

1 in.

(25 mm)

1 in.

(25 mm)

1 in.*

(25 mm)

12 in.

(300 mm)

16-3/8 in.

(416 mm)

16-3/8 in.

(416 mm)

19-1/4 in.

(490 mm)

19-1/4 in.

(490 mm)

22 in.

(560 mm)

22 in.

(560 mm)

22 in.

(560 mm)

25 in.

(635 mm)

26-1/4 in.

(667 mm)

25-5/8 in.

(650 mm)

29-7/16 in.

(705 mm)

30-1/2 in.

(775 mm)

34 in.

(864 mm)

36 in.

(914 mm)

37-1/2 in.

(953 mm)

38-3/4 in.

(984 mm)

51-5/8 in.

(1311 mm)

56-3/4 in.

(1441 mm)

12 in.

(305 mm)

12 in.

(305 mm)

12 in.

(305 mm)

18 in.

(457 mm)

12 in.

(305 mm)

12 in.

(305 mm)

12 in.

(305 mm)

24 in.

(610 mm)

24 in.

(610 mm)

*For 80 pound models intended for standard mounting, clearance should be 6 in. (150 mm).

Installation

F232135

Machine Foundation

NOTE: Do not mount on wooden floors, above

ground level, or over basements or crawl spaces

because of the high extract speed and the G-forces

exerted.

The floor must be 3500 psi minimum reinforced

concrete set firmly in clean, compacted fill dirt.

The machine must be anchored to a smooth, level

surface so that the entire base of the machine is

supported and rests on the mounting surface. (Do not

support the machine on only four points.)

An elevated foundation must not exceed 8 inches

(203 mm).

Refer to Table 2 for foundation and anchoring

requirements.

Machine Foundation Requirements

Models

Foundation

Thickness

Floor

Thickness

Installation

Foundation

Method(s)

Anchoring

Method(s)

Requirement

Anchoring

Bolt

Diameter

Size

(minimum)

2 Speed and Fixed-Speed

(20-60 Models)

in.

(102 mm)

4 in.

(102 mm)

Direct-to-finished-floor,

elevated base frame, or

concrete foundation

Expansion bolt

or J-bolt

5/8 in.

Variable-Speed

(20-60 Models)

6 in.

(152 mm)

6 in.

(152 mm)

Direct-to-finished-floor

or concrete foundation

J-bolt or

mounting bolt

5/8 in.

Variable-

Speed

80 Models 9 in.

(229 mm)

6 in.

(152 mm)

Direct-to-finished-floor

or concrete foundation

J-bolt, mounting

bolt, or rebar

frame

3/4 in.

125 Models 12 in.

(304 mm)

6 in.

(152 mm)

Table 2

Installation

F232135

NOTE: For 80 and 125 pound models, a

bolt-locator fixture or rebar frame is available as

an option. This is designed to be embedded in

concrete. Refer to Figure 10.

IMPORTANT: Do not install any variable-speed

machine on an elevated base frame.

Figure 10

P035I

1 Machine Base

2 Mounting Bolt Threads

3 Grouting

4 Bolt-Locator Fixture or Rebar Frame

P035I

Installation

F232135

Refer to Table 3 and Table 4 for static and dynamic

loads on the floor or foundation.

Floor Load Data, 2 Speed Models

Specification 18, 20 25 27, 30 35 40 50 60

Static floor load,

lbs. (kN)

476

(2.12)

549

(2.44)

653

(2.90)

804

(3.58)

873

(3.88)

1041

(4.63)

1015

(4.53)

Static pressure,

lbs-ft

(kN-m

)

104

(4.96)

103

(4.94)

106.3

(5.10)

113

(5.41)

123

(5.89)

117

(5.62)

115

(5.5)

Dynamic load,

lbs. (kN)

296

(1.31)

420

(1.87)

427

(1.90)

581

(2.58)

987

(4.4)

860

(3.83)

1418

(6.3)

Dynamic pressure,

lbs-ft

(kN-m

)

64.4

(3.08)

79.3

(3.80)

(3.33)

(3.91)

139

(6.7)

(4.64)

161

(7.6)

Dynamic load

frequency, Hz

8.75 9.00 8.00 7.83 7.80 7.50 7.50

Maximum moment

about machine base,

lbs-ft (kN-m)

565

(0.769)

832

(1.0)

847

(1.16)

1247

(1.6)

2118

(2.9)

1894

(2.4)

2470

(3.35)

Table 3

Floor Load Data, Variable-Speed Models

Specification 20303540506080125

Static floor load, lbs. (kN) 513

(2.27)

688

(3.01)

934

(4.1)

873

(3.88)

1136

(5.0)

914

(4.07)

1972

(8.8)

2316

(10.3)

Static pressure, lbs-ft

(kN-m

)112

(5.35)

112

(5.35)

132

(6.3)

123

(5.89)

128

(6.1)

103

(4.95)

144

(6.9)

145

(6.93)

Dynamic load, lbs. (kN) 512

(2.27)

7.55

(3.36)

979

(4.35)

1123

(5)

1397

(6.25)

1428

(6.3)

2243

(9.98)

3500

(15.5)

Dynamic pressure, l

bs-ft

(kN-m

)

112

(5.35)

123

(5.88)

138

(6.60)

158

(7.6)

159

(7.5)

161

(7.6)

164

(7.84)

364

(17.4)

Dynamic load frequency, Hz 11.5 10.7 10.22 10.2 9.58 9.58 8.73 8.08

Maximum moment about

machine base, lbs-ft (kN-m)

979

(1.33)

1510

(2.05)

2122

(2.7)

2410

(3.3)

3071

(3.9)

3138

(4.25)

5749

(7.2)

11,667

(14.7)

Table 4

Installation

F232135

Machine Anchoring

Before anchoring the machine, refer to Table 2 to

determine the appropriate method of anchoring for the

machine.

NOTE: Improper installation may void the

warranty. Consult the manufacturer or distributor

before varying from a procedure.

Direct-to-Finished-Floor Installation

Installing With Expansion Bolts

(2 Speed Models, Fixed-Speed and

A-Control Variable-Speed Models)

NOTE: Expansion bolts are not suitable VNV

machine installations.

1. Verify the floor meets the requirements given in

the Machine Foundation section.

2. Mounting surface should be level and machine

must be properly grouted.

NOTE: If replacing a 35 pound machine with a

40 pound machine, note differences in cabinet size.

Refer to pages 20, 21 and 32.

NOTE: If replacing a 50 pound machine with a

60 pound machine, note differences in cabinet size.

Refer to pages 20, 21 and 32.

3. Use the base of the machine as a template by

positioning the machine in the desired location

and marking the pre-drilled mounting holes on

the floor. Metal templates are available at cost

through Alliance Laundry Systems. Refer to

Table 5 for ordering information.

4. Set the drill depth gauge to 2-9/16 inches

(65 mm).

5. Drill the holes to the set depth. Refer to Figure

11.

6. Use compressed air or a squeeze bulb to clean out

each hole.

7. Install the machine anchors, using the included

tool.

8. Secure the machine to the floor, using the bolts

furnished with the anchors. Tighten the locknuts

by even increments – one after the other – until

all are tightened evenly and the machine is

fastened securely to the floor. Refer to Figure 12.

Figure 11

Figure 12

The completed expansion bolt installation is shown in

Figure 13.

Figure 13

U137I

H029I

CHM2032N

1 Washer

2 Locknut

3 Machine Base

4 5/8 in. (19 mm) Diameter Expansion Bolt

U137I

2-9/16 in.

(65 mm)

H029I

CHM203

2-9/16 in.

(65 mm)

Installation

F232135

Installing With J-Bolts

1. Verify the floor meets the requirements given in

the Machine Foundation section.

2. Install J-bolts in concrete as shown in the

mounting bolt layouts (Figure 18 and Figure 19)

following these instructions.

NOTE: If replacing a 35 pound machine with a

40 pound machine, note differences in cabinet size.

Refer to pages 20, 21 and 32.

NOTE: If replacing a 50 pound machine with a

60 pound machine, note differences in cabinet size.

Refer to pages 20, 21 and 32.

NOTE: There are two different mounting bolt

layouts which may be used for the 80 pound

capacity machine. Refer to Figure 19. The bolt holes

marked “A” are to be used for close mounting –

machines installed with a 1 inch (25.4 mm)

clearance between machines. The bolt holes marked

“B” are to be used for standard mounting –

machines installed with a minimum clearance of

8 inches (203 mm) between machines.

3. Adjust the drill depth gauge to match the length

of the J-bolt, minus 1-1/2 inches (38 mm).

4. Drill and chisel out a conical hole large enough to

accept the J-bolt. Refer to Figure 14.

Figure 14

5. Use compressed air or a squeeze bulb to remove

debris from each hole. Anchor J-bolt in place,

using an industry-accepted anchoring compound.

Verify that the J-bolts are in the correct locations

and that 1-1/2 inches (38 mm) of each J-bolt

protrude from the floor. Refer to Figure 15.

Figure 15

6. Place the machine carefully over the J-bolts.

Never attempt to lift the machine by the door

handle or by pushing on the cover panels.

H031I

H032I

1-1/2 in.

(38 mm)

Installation

F232135

7. If grouting is not desired, position washers and

locknuts on J-bolts and tighten the locknuts by

even increments – one after the other – until all

are tightened evenly and the machine is fastened

securely to the floor. Refer to Figure 16.

8. If grouting is desired (or required by the

condition of the mounting surface), proceed

to step 11.

9. If the machine is a variable-speed model, the

machine must be grouted. Proceed to step 11.

10. Raise and level the machine 1/2 inch (13 mm) off

the floor on three points, using spacers such as

nut fasteners.

11. Fill the space between the machine base and the

floor with a good quality non-shrinking

machinery grout to ensure a stable installation.

Grout completely under all frame members.

12. Remove the spacers carefully, allowing the

machine to settle into the wet grout.

13. Before grout sets completely, make a drain

opening in the rear of the machine grouting with

a stiff piece of wire. This opening should be

approximately 1/2 inch (13 mm) wide to allow

any surface water build-up under the base of the

machine to drain away. Do not omit this step.

14. Position washers and locknuts on J-bolts and

fingertighten nuts to machine base.

15. After the grout is completely dry, tighten the

locknuts by even increments – one after the

other – until all are tightened evenly and the

machine is fastened securely to the floor.

16. Balance Switch Adjustment: After mounting,

reset balance switch to the correct gap switch

setting. Refer to Table 1.

NOTE: Be sure to recheck the J-bolts 1 week after

installation.

Figure 16

Figure 17 shows the completed J-bolt installation with

grout.

Figure 17

H033I

U139I

1 Foundation

2 Locknut

3 Machine Base

4 1/2 in. (13 mm) Machinery Grout

5 J-Bolt

H033I

U139I

1-1/2 in.

(38 mm)

Installation

F232135

Mounting Bolt Template Part

Numbers (Without Elevated Base

Frame)

Metal templates are available at cost through Alliance

Laundry Systems at (920) 748-3121. Refer to Table 5

for specific Part Numbers when ordering.

Machine Part No.

18/20 F608707

25 F608708

27/30 F631796

35 F608709

40 F0637047-00

50/60 F608710

80 F609692

125 F601862

Table 5

Installation

F232135

Mounting Bolt Hole Locations (Without Elevated Base Frames)

Figure 18

CHM2020N

*For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.”

CHM2020N

18 AND 20 POUND

25 POUND

27 AND 30 POUND

26 in.

(660 mm)

31.75 in.

(806 mm)

23.94 in.

(608 mm)

26 in.

(660 mm)

27.94 in.

(710 mm)

20.88 in.

(530 mm)

2.56 in.

(65 mm)

0.75 in.

(19 mm)

2.56 in.

(65 mm)

0.75 in.

(19 mm)

2.56 in.

(65 mm)

20.88 in.

(530 mm)

23.88 in.

(607 mm)

26 in.

(660 mm)

20.66 in.

(525 mm)

18.31 in.

(465 mm)

34.88 in.

(885 mm)

27.69 in.

(705 mm)

2.68 in.

(68 mm)

28.94 in.

(735 mm)

18.44 in.

(468 mm)

2.75 in.

(70 mm)

2.75 in.

(70 mm)

29 in.

(737 mm)

23.5 in.

(597 mm)

37.52 in.

(953 mm)

30.02 in.

(762 mm)

2.56 in.

(65 mm)

2.56 in.

(65 mm)

31.5 in.

(800 mm)

0.75 in.

(19 mm)

50 POUND

34.06 in.

(865 mm)

3.28 in.

(83 mm)

3.28 in.

(83 mm)

27.5 in.

(700 mm)

46.88 in.

(1191 mm)

37.44 in.

(951 mm)

36 in.

(914 mm)

24.07 in.

(611 mm)

0.75 in.

(19 mm)

2.03 in.

(52 mm)

2.03 in.

(52 mm)

30 in.

(760 mm)

37.5 in.

(953 mm)

2.68 in.

(68 mm)

30 in.

(762 mm)

2.56 in.

(65 mm)

Installation

F232135

Mounting Bolt Hole Locations (Without Elevated Base Frames)

Figure 19

CHM2018N

*For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.”

80 POUND* 125 POUND

33.5 in.

(851 mm)

40 in.

(1016 mm)

4 in.

(102 mm)

5 in.

(127 mm)

17 in.

(432 mm)

0.75 in.

(19 mm)

4 in.

(102 mm)

28.5 in.

(724 mm)

41.5 in.

(1054 mm)

33.5 in.

(851 mm)

31.5 in.

(800 mm)

4 in.

(102 mm)

4 in.

(102 mm)

0.75 in.

(19 mm)

5 in.

(127 mm)

9.5 in.

(241 mm)

11 in.

(279 mm)

47.5 in.

(1207 mm)

25 in.

(635 mm)

46.5 in.

(1181 mm)

0.75 in.

(19 mm)

0.75 in.

(19 mm)

10 in.

(254 mm)

15 in.

(381 mm)

15.25 in.

(388 mm)

0.75 in.

(19 mm)

23.25 in.

(591 mm)

23.25 in.

(591 mm)

48 in.

(1219 mm)

48.94 in.

(1243 mm)

61.5 in.

(1562 mm)

48 in.

(1219 mm)

1 in.

(25 mm)

55.47 in.

(1409 mm)

A A

B B

AAB B

35 POUND

30.13 in.

(765 mm)

23.63 in.

(600 mm)

41.63 in.

(1057 mm)

31.88 in.

(810 mm)

3.25 in.

(83 mm)

32.5 in.

(826 mm)

20 in.

(508 mm)

34 in.

(864 mm)

26 in.

(660 mm)

2.06 in.

(52 mm)

2.06 in.

(52 mm)

0.75 in.

(19 mm)

3.25 in.

(83 mm)

32.5 in.

(826 mm)

20 in.

(508 mm)

23.63 in.

(600 mm)

41.63 in.

(1057 mm)

31.88 in.

(810 mm)

3.25 in.

(83 mm)

36 in.

(914 mm)

26 in.

(660 mm)

30.13 in.

(765 mm)

1.5 in.

(38 mm)

40 POUND

2.06 in.

(52 mm)

1 in.

(25 mm)

CHM2005N

60 POUND

34.06 in.

(865 mm)

3.28 in.

(83 mm)

3.28 in.

(83 mm)

27.5 in.

(700 mm)

46.88 in.

(1191 mm)

37.44 in.

(951 mm)

36 in.

(914 mm)

24.07 in.

(611 mm)

0.75 in.

(19 mm)

2.03 in.

(52 mm)

2.03 in.

(52 mm)

30 in.

(760 mm)

37.5 in.

(953 mm)

CHM2005N

Installation

F232135

Mounting Bolt Hole Locations (With Elevated Base Frames)

Figure 20

CHM2021N

*For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.”

CHM2021N

18 AND 20 POUND

25 POUND

27 AND 30 POUND

26.4 in.

(670 mm)

31.75 in.

(806 mm)

23.94 in.

(608 mm)

26.2 in.

(665 mm)

27.94 in.

(710 mm)

20.88 in.

(530 mm)

2.75 in.

(70 mm)

1.13 in.

(29 mm)

2.75 in.

(70 mm)

1.13 in.

(29 mm)

2.75 in.

(70 mm)

20.88 in.

(530 mm)

23.88 in.

(607 mm)

26.4 in.

(670 mm)

20.66 in.

(525 mm)

18.31 in.

(465 mm)

34.88 in.

(885 mm)

27.69 in.

(705 mm)

2.87 in.

(73 mm)

28.94 in.

(735 mm)

18.44 in.

(468 mm)

2.94 in.

(75 mm)

2.94 in.

(75 mm)

29.4 in.

(747 mm)

23.5 in.

(597 mm)

37.52 in.

(953 mm)

30.02 in.

(762 mm)

2.75 in.

(70 mm)

2.75 in.

(70 mm)

31.2 in.

(792 mm)

1.13 in.

(29 mm)

30.5 in.

(775 mm)

3.44 in.

(87 mm)

3.44 in.

(87 mm)

23.63 in.

(600 mm)

41.63 in.

(1057 mm)

31.88 in.

(810 mm)

32.5 in.

(826 mm)

20 in.

(508 mm)

1.13 in.

(29 mm)

2.25 in.

(57 mm)

2.25 in.

(57 mm)

26 in.

(660 mm)

34.75 in.

(883 mm)

2.87 in.

(73 mm)

30.2 in.

(767 mm)

2.75 in.

(70 mm)

20.66 in.

(525 mm)

35 POUND

2.87 in.

(73 mm)

2.87 in.

(73 mm)

14.31 in.

(363 mm)

25.22 in.

(640 mm)

Installation

F232135

Mounting Bolt Hole Locations (With Elevated Base Frames)

Figure 21

CHM2022N

*For close mounting, use mounting bolt pattern labeled “A”; for standard mounting, use “B.”

CHM2022N

40 POUND 50 POUND

60 POUND

23.63 in.

(600 mm)

31.88 in.

(810 mm)

36 in.

(914 mm)

30.88 in.

(784 mm)

2.38 in.

(61 mm)

2.44 in.

(62 mm)

1.13 in.

(29 mm)

2.22 in.

(56 mm)

30 in.

(762 mm)

30 in.

(762 mm)

34.5 in.

(876 mm)

27.5 in.

(700 mm)

24 in.

(610 mm)

46.88 in.

(1191 mm)

37.44 in.

(951 mm)

3.47 in.

(88 mm)

36 in.

(914 mm)

24 in.

(610 mm)

3.47 in.

(88 mm)

3.47 in.

(88 mm)

34.5 in.

(876 mm)

27.5 in.

(700 mm)

46.88 in.

(1191 mm)

37.44 in.

(951 mm)

2.22 in.

(56 mm)

2.22 in.

(56 mm)

38.9 in.

(988 mm)

2.13 in.

(54 mm)

3.47 in.

(88 mm)

38.25 in.

(972 mm)

2.22 in.

(56 mm)

20 in.

(508 mm)

32.5 in.

(826 mm)

3.62 in.

(92 mm)

26 in.

(660 mm)

41.63 in.

(1057 mm)

36 in.

(914 mm)

Installation

F232135

Elevated Base Frame Installation

Factory-built elevated steel base frames are designed

to meet the specifications of the 20-60 2 speed,

F speed and A-control variable-speed model washer-

extractor only. Refer to Figure 22.

Figure 22

Installing With Elevated Base Frame

1. Verify the floor meets the requirements given in

the Machine Foundation section.

2. Use the elevated base frame as a template by

positioning the frame in the desired location and

marking the pre-drilled mounting holes on the

floor.

3. Adjust the drill depth gauge to match the length

of the J-bolt, minus 1-1/2 inches (38 mm).

4. Drill and chisel out a conical hole large enough to

accept the J-bolt. Refer to Figure 23.

Figure 23

5. Use compressed air or a squeeze bulb to remove

debris from each hole. Anchor J-bolt in place,

using an industry-accepted anchoring compound.

Verify that the J-bolts are in the correct locations

and that 1-1/2 inches (38 mm) of each J-bolt

protrude from the floor. Refer to Figure 24.

Figure 24

H035I

H031I

H032I

H031I

H032I

1-1/2 in.

(38 mm)

Installation

F232135

6. Raise and level the base frame 1/2 inch (13 mm)

off the floor on three points, using spacers such

as nut fasteners.

7. Fill the space between the frame base and the

floor with a good quality non-shrinking

machinery grout to ensure a stable installation.

Grout completely under all frame members.

8. Remove the spacers carefully, allowing the base

frame to settle into the wet grout.

9. Before grout sets completely, make a drain

opening in the rear of the base frame grouting

with a stiff piece of wire. This opening should be

approximately 1/2 inch (13 mm) wide to allow

any surface water build-up under the base of the

machine to drain away. Do not omit this step.

10. Position washers and locknuts on J-bolts and

fingertighten nuts to base frame.

11. After the grout is completely dry, tighten locknuts

by even increments – one after the other – until

all are tightened evenly and the base frame is

fastened securely to the floor. Refer to Figure 16.

12. Position the machine over the base frame, aligning

the mounting holes on the machine with the

corresponding holes on the frame.

13. Install a bolt, lockwasher, and nut in each

mounting hole. Use 5/8 inch – 18 x 2

grade 5 mounting bolts with 5/8 inch – 18

grade B nuts and 5/8 inch lockwashers.

14. Handtighten each nut.

15. Tighten the two rear nuts two turns.

16. Tighten the two front nuts two turns.

17. On 25, 27, 30, 35, 40, 50 and 60 models, tighten

the two middle nuts firmly.

18. Tighten the two front nuts firmly; tighten the two

rear nuts firmly.

NOTE: Recheck the elevated base frame

installation one week after installation.

Installation

F232135

Concrete Foundation Installation

A concrete foundation pad may be constructed to

elevate the machines. Refer to Figure 25, Figure 26 or

Figure 27 for a typical concrete foundation

installation.

NOTE: Expansion bolts should not be used in

single-machine concrete foundation installations.

1. Verify that the floor meets the requirements given

in the Machine Foundation section.

2. Excavate the floor to a depth of approximately

9 inches (230 mm) below the floor surface,

making certain that the sides of the hole slope

outwards from top to bottom. The bottom of the

hole should be 6 inches (152 mm) larger all

around than the top.

NOTE: When installation is complete, the top

of the foundation should extend a minimum of

4 inches (102 mm) out from the machine on all

sides.

3. Wet the hole well and brush the bottom and sides

with cement grout.

Figure 25

CHM2033N

1 Pad height must not exceed 8 in. (203 mm)

2 1 in. (25 mm) Minimum

3 4 in. (102 mm) Minimum

CHM2033N

18, 20, 25, 27, 30, 35, 40, 50 AND 60 POUND CAPACITY MODELS

Installation

F232135

Figure 26

Figure 27

B153I

1 9 in. (229 mm) 3 47-1/2 in. (1207 mm)

2 6 in. (152 mm) 4 4 ft. 6 in. (1372 mm)

B153I

80 POUND CAPACITY MODELS

LENGTH FOR ONE MACHINE

COMPACTED FILL DIRT 18 in. (457 mm) DEPTH

B154I

1 12 in. (305 mm) 3 48 in. (1219 mm)

2 6 in. (152 mm) 4 6 ft. (1829 mm)

B154I

125 POUND CAPACITY MODELS

COMPACTED FILL DIRT 24 in. (609 mm) DEPTH

LENGTH FOR ONE MACHINE

COMPACTED FILL DIRT 24 in. (609 mm) DEPTH

Installation

F232135

4. Use rebar or other appropriate material to ensure

that the concrete foundation will be sufficiently

connected to the existing floor.

5. If desired, prepare a form for the above-ground

portion of the foundation and fill form and

excavation with concrete to join the foundation.

Verify that top of foundation is level. The height

of the foundation must not exceed 8 inches

(203 mm).

6. Use the mounting bolt layout to properly position

the mounting bolts in the wet concrete. When

using J-bolts, allow 1-1/2 inches

(38 mm) to extend above the surface of the

concrete.

7. Allow concrete to dry.

8. Place the machine carefully over the mounting

bolts. Never attempt to lift the machine by the

door handle or by pushing on the cover panels.

NOTE: Grouting provides a uniform mounting

surface. Grouting is optional for 2 speed models

and is required for variable-speed models installed

on a concrete foundation. If grouting is not

required, proceed to step 13.

9. Raise and level the machine 1/2 inch (13 mm) off

the foundation on three points, using spacers

such as nut fasteners.

10. Fill the space between the machine base and the

foundation with a good quality non-shrinking

machinery grout to ensure a stable installation.

Grout completely under all frame members.

11. Remove the spacers carefully, allowing the

machine to settle into the wet grout.

12. Before grout sets completely, make a drain

opening in the rear of the machine grouting with

a stiff piece of wire. This opening should be

approximately 1/2 inch (13 mm) wide to allow

any surface water build-up under the base of the

machine to drain away. Do not omit this step.

13. Position washers and locknuts on J-bolts or

mounting bolts and fingertighten nuts to machine

base.

14. After the grout is completely dry, tighten the

locknuts by even increments – one after the

other – until all are tightened evenly and the

machine is fastened securely to the concrete

foundation.

Installation

F232135

Drain Connection

Figure 28 and Figure 29 show typical drain trough and

drain line installations.

Connect the drain outlet to a vented drain system using

only a flexible connection. The drain system must be

vented to prevent an air lock or siphoning.

Use the supplied black rubber adapter and clamps to

transition from the machine drain outlet to the two

inch schedule 40 PVC plumbing (20, 25 and 30

models) and the three inch schedule PVC plumbing

(40, 60 and 80 models).

If proper drain size is not available or practical, a surge

tank is required. A surge tank along with a sump pump

should be used when gravity drainage is not possible,

such as in below-ground-level installations.

Figure 28

Figure 29

H050I

1 Drain Hose 4 Drain Tee

2 Drain Valve 5 Floor

3 Overflow Hose 6 Open Drain Trough

H050I

DRAIN TROUGH

CHM2010N

1 Drain Hose 4 Overflow Hose

2 Drain Valve 5 Vent Pipe

3 Drain Tee 6 Water Inlet Valve*

* 1 foot (0.3 m) minimum between water inlet valve and vent pipe.

1 ft.

(0.3 m)

DRAIN LINE

Installation

F232135

IMPORTANT: Increasing the drain hose length,

installing elbows, or causing bends will decrease

drain flow rates and increase drain times,

impairing machine performance.

Refer to Table 6 for capacity-specific drain

information.

NOTE: Installation of additional machines will

require larger drain connections. Refer to Table 7.

* Also works with 3 inch OD PVC pipe if connected to inside of

drain tee connector.

Drain Information

18, 20 25 27, 30 35 40 50 60 80 125

Drain connection

size, OD

2.38 in.

(60 mm)

2.38 in.

(60 mm)

2.38 in.

(60 mm)

2.38 in.

(60 mm)

3.5 in.*

(89 mm)

3.5 in.*

(89 mm)

3.5 in.*

(89 mm)

3.5 in.*

(89 mm)

3.5 in.*

(89 mm)

Number of drain

outlets

111111111

Drain flow

capacity

20 gal-min

(76 l-min)

25 gal-min

(95 l-min)

25 gal-min

(95 l-min)

35 gal-min

(132 l-min)

50 gal-min

(189 l-min)

50 gal-min

(189 l-min)

50 gal-min

(189 l-min)

50 gal-min

(189 l-min)

70 gal-min

(265 l-min)

Recommended

drain pit size

1.80 ft

(51 l)

2.36 ft

(66.8 l)

2.50 ft

(70.3 l)

3.14 ft

(88.9 l)

4.52 ft

(128 l)

4.52 ft

(128 l)

4.52 ft

(128 l)

5.90 ft

(169 l)

13 ft

(368 l)

Table 6

Drain Line Sizing

Minimum Drain ID

Model

Number of Machines

12345

18, 20

in. (52 mm) 3 in. (76 mm) 3 in. (76 mm) 4 in. (102 mm) 4 in. (102 mm)

27, 30

in. (52 mm) 3 in. (76 mm) 3 in. (76 mm) 4 in. (102 mm) 4 in. (102 mm)

in. (76 mm) 3 in. (76 mm) 3-1/2 in. (89 mm) 4 in. (102 mm) 4 in. (102 mm)

in. (76 mm) 4 in. (102 mm) 4 in. (102 mm) 4 in. (102 mm) 6 in. (152 mm)

80, 125

in. (76 mm) 4 in. (102 mm) 4 in. (102 mm) 6 in. (152 mm) 6 in. (152 mm)

Table 7

Installation

F232135

Water Connection Requirements

Connections should be supplied by a hot and a cold

water line of at least the sizes shown in Table 8.

Installation of additional machines will require

proportionately larger water lines.

To connect water service to machine with rubber

hoses, use the following procedure:

1. Before installing hoses, flush the water system

for at least 2 minutes.

2. Check filters in the machine’s inlet hoses for

proper fit and cleanliness before connecting.

3. Hang hoses in a large loop; do not allow them to

kink.

If additional hose lengths are needed, use flexible

hoses with screen filters.

Suitable air cushions should be installed in supply

lines to prevent “hammering.” Refer to Figure 30.

Figure 30

Water Supply Line Sizing

Model

Number

Machines

Supply Line Size

Main Hot/Cold

18 – 60

13/4 in. (19 mm) 1/2 in. (13 mm)

in. (25 mm) 3/4 in. (19 mm)

31-1/4

in. (32 mm) 1 in. (25 mm)

41-1/2

in. (38 mm) 1 in. (25 mm)

11 in. (25 mm) 3/4 in. (19 mm)

21-1/2

in. (38 mm) 1 in. (25 mm)

in. (50 mm) 1-1/4 in. (32 mm)

in. (50 mm) 1-1/2 in. (38 mm)

125

11-1/2 in. (38 mm) 1 in. (25 mm)

in. (50 mm) 1-1/2 in. (38 mm)

in. (50 mm) 2 in. (50 mm)

42-1/2

in. (70 mm) 2 in. (50 mm)

Table 8

MW008J

1 Water Supply Faucets

2 Air Cushions (Risers)

MW008J

Installation

F232135

Electrical Installation Requirements

IMPORTANT: Electrical ratings are subject to

change. Refer to serial decal for electrical ratings

information specific to your machine.

Machines equipped with an AC inverter drive require a

clean power supply, free from voltage spikes and

surges. Use voltage monitor to check incoming power.

The customer’s local power company may provide

such a monitor.

Input Voltage Requirements

If input voltage measures above rated maximum

voltage, ask the power company to lower voltage.

For voltages above or below listed specifications,

contact Customer Service or a distributor for buck/

boost transformer recommendation. Refer to

Electrical Specification section.

If machine is intended for four-wire service, a neutral

leg must be provided by power company.

If a delta supply system is used on a four-wire model,

connect high leg to L3.

IMPORTANT: Alliance Laundry Systems

warranty does not cover components that fail as a

result of improper input voltage.

IMPORTANT: Improper connections will result in

equipment damage and will void warranty.

IMPORTANT: For machines with X voltage: If

input power is single-phase, connect L1 to R of

terminal block and L2 to S of terminal block. Leave

T unconnected on the input terminal block. If input

power is three-phase, connect L1, L2 and L3 to R, S

and T of the terminal block.

Circuit Breakers

Single-phase machines require a single-phase inverse-

time circuit breaker. Three-phase machines and

variable-speed machines require a separate, three-

phase inverse-time circuit breaker to prevent damage

to the motor by disconnecting all legs if one should

be lost accidentally. Check the nameplate decal on

the back of the machine. Refer to Table 9 through

Table 16 in this section for model-specific circuit

breaker requirements.

Hazardous Voltage. Can cause shock,

burn or cause death. Allow machine

power to remain off for two minutes prior

to working in and around AC inverter

drive.

W359

WARNING

Hazardous Voltage. Can cause shock,

burn or death. Verify that a ground wire

from a proven earth ground is connected

to the lug near the input power block on

this machine.

W360

WARNING

Hazardous Rotation Speed. Will cause

serious injury when controlling AC

inverter drive with a parameter unit,

safety features are bypassed allowing

basket to rotate at high speeds with the

door open. Place large sign on front of

machine to warn people of imminent

danger.

W361

DANGER

Installation

F232135

Connection Specifications

IMPORTANT: Connection must be made by a

qualified electrician using wiring diagram provided

with machine, or according to accepted European

standards for CE-approved equipment.

Connect machine to an individual branch circuit not

shared with lighting or other equipment. Shield

connection in a liquid-tight or approved flexible

conduit. Proper conductors of correct size must be

installed in accordance with National Electric Code or

other applicable codes.

Use wire sizes indicated in the Electrical Specifications

chart for runs up to 50 feet (15 m). Use next larger size

for runs of 50 to 100 feet (15 to 30 m). Use two sizes

larger for runs greater than 100 feet (30 m).

Grounding

For personal safety and proper operation, the machine

must be grounded in accordance with state and local

codes. If such codes are not available, grounding must

conform to the National Electric Code, article 250-95.

The ground connection must be made to a proven earth

ground, not to conduit or water pipes.

Do not connect ground to neutral (N-white wire) leg at

terminal strip.

Phase Adder

If three-phase service is unavailable for a 2 speed

model and a Roto-Phase or other phase adder is used,

connect artificial leg to L3 in input power junction

box.

IMPORTANT: Do not use a phase adder on any

variable-speed machine.

Thermal Overload Protector

Two speed machines have thermal overload protectors

in drive motor windings and a separate fuse for control

circuit.

For variable-speed machines, the AC drive provides

overload protection for the drive motor.

Installation

F232135

Electrical Specifications

18 and 20 Pound Capacity Models

Voltage Designation Standard Electric Heat

Code

Voltage

Cycle

Phase

Wire

Full Load

Amps

Circuit

Breaker

AWG

Full Load

Amps

Circuit

Breaker

AWG

2 Speed Models

B 110 – 120 60 1 2 15 20 12 4 N/A

C 380 – 415 50 3 4 4 15 14 2.5 14 15 14 2.5

D 220 – 240 50 3 3 5 15 14 2.5 24 25 10 6

E220 – 2405012102012 4 4245 6 16

F 440 – 480 60 3 3 4 15 14 2.5 16 20 12 4

H 380 60 3 3 4 15 14 2.5 13 15 14 2.5

J 200 50 3 3 5 15 14 2.5 24 25 10 6

O 208 – 240 60 3 3 5 15 14 2.5 24 25 10 6

Y208 – 2406012102012 4 4245 6 16

Variable-Speed Models

Q 200 – 240 50/60 3 3.8 3.8 15 14 2.5 N/A N/A N/A N/A

NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.

Table 9

Electrical Specifications

25, 27 and 30 Pound Capacity Models

Voltage Designation Standard Electric Heat

Code

Voltage

Cycle

Phase

Wire

Full Load

Amps

Circuit

Breaker

AWG

Full Load

Amps

Circuit

Breaker

AWG

2 Speed Models

C 380 – 415 50 3 4 4 15 14 2.5 15 20 12 4

D 220 – 240 50 3 3 6 15 14 2.5 24 25 10 6

E220 – 2405012102012 4 4245 6 16

F 440 – 480 60 3 3 4 15 14 2.5 16 20 12 4

H 380 60 3 3 4 15 14 2.5 14 15 14 2.5

J 200 50 3 3 6 15 14 2.5 20 25 10 6

O 208 – 240 60 3 3 7 15 14 2.5 25 30 10 6

Y 208 – 240 60 1 2 10 20 12 4 43

45616

Variable-Speed Models

Q 200 – 240 50/60 3 3 4.8 15 14 2.5 N/A N/A N/A N/A

NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.

Tabl e 10

Installation

F232135

Electrical Specifications

35 Pound Capacity Models

Voltage Designation Standard Electric Heat

Code

Voltage

Cycle

Phase

Wire

Full Load

Amps

Circuit

Breaker

AWG

Full Load

Amps

Circuit

Breaker

AWG

2 Speed Models

C 380 – 415 50 3 4 5 15 14 2.5 26 30 10 6

D 220 – 240 50 3 3 7 20 12 4 43 50 6 16

F 440 – 480 60 3 3 5 15 14 2.5 26 30 10 6

O 200 – 240 60 3 3 7 20 12 4 43 50 6 16

Y 208 – 240 60 1 2 12 25 10 6 N/A

Variable-Speed Models

N 440 – 480 50/60 3 3 2.3 15 14 2.5 27.3 30 10 6

P 380 – 415 50/60 3 3 2.3 15 14 2.5 24 25 10 6

Q 208 – 240 50/60 3 3 5.9 15 14 2.5 43.4 45 6 16

T 200 – 240 50/60 1 2 5.9 15 14 2.5 N/A

X 200 – 240 50/60 1 or 3 2 or 3 5.9/5.9 15 14 2x2.5

3x2.5

N/A

NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.

Tabl e 11

Electrical Specifications

40 Pound Capacity Models

Voltage Designation Standard Electric Heat

Code

Voltage

Cycle

Phase

Wire

Full Load

Amps

Circuit

Breaker

AWG

Full Load

Amps

Circuit

Breaker

AWG

2 Speed Models

C 380 – 415 50 3 4 5 15 14 2.5 26 30 10 6

D 220 – 240 50 3 3 7 20 12 4 45 50 6 16

F 440 – 480 60 3 3 5 15 14 2.5 29 30 10 6

H 380 60 3 3 3 15 14 2.5 25 30 10 6

J 200 50337201243840616

O 208 – 240 60 3 3 7 20 12 4 45 50 6 16

Y 208 – 240 60 1 2 13.5 30 10 6 N/A

Variable-Speed Models

N 440 – 480 50/60 3 3 6 15 14 2.5 30 30 10 6

P 380 – 415 50/60 3 3 6 15 14 2.5 29 30 10 6

Q 200 – 240 50/60 3 3 5 15 14 2.5 48 60 6 16

X 200 – 240 50/60 1 or 3 2 or 3 11/11 15 14 2.5 N/A

NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.

Tabl e 12

Installation

F232135

Electrical Specifications

50 Pound Capacity Models

Voltage Designation Standard Electric Heat

Code

Voltage

Cycle

Phase

Wire

Full Load

Amps

Circuit

Breaker

AWG

Full Load

Amps

Circuit

Breaker

AWG

2 Speed Models

C 380 – 415 50 3 4 6 15 14 2.5 39 50 6 16

D220 – 2405033122012 4 6470 4 25

E220 – 2405012153010 6 3740 8 10

F 440 – 480 60 3 3 6 15 14 2.5 39 50 6 16

J 200 50 3 3 10 20 12 3 x 4 N/A

O208 – 2406033102012 4 6470 4 25

Y*208 – 2406012153010 6 3740 8 10

Variable-Speed Models

N 440 – 480 50/60 3 3 4 15 14 2.5 41.6 45 8 10

P 380 – 415 50/60 3 3 4 15 14 2.5 36.5 40 8 10

Q 200 – 240 50/60 3 3 6.3 15 14 2.5 62.6 70 4 25

T 200 – 240 50/60 1 2 6.3 15 14 2.5 N/A

X 200 – 240 50/60 1 or 3 2 or 3 6.3/6.3 15 14 2x2.5

3x2.5

N/A

NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.

*Coin models only.

Tabl e 13

Installation

F232135

Electrical Specifications

60 Pound Capacity Models

Voltage Designation Standard Electric Heat

Code

Voltage

Cycle

Phase

Wire

Full Load

Amps

Circuit

Breaker

AWG

Full Load

Amps

Circuit

Breaker

AWG

2 Speed Models

C 380-415 50 3 4 4 15 14 2.5 37 50 8 10.0

D 220-240 50 3 3 7 20 12 4.0 64 70 4 25.0

F 440-480 60 3 3 4 15 14 2.5 41 50 8 10.0

H 380 60 3 3 3 20 12 4.0 33 50 8 10.0

J 200 50 3 3 8 20 12 4.0 55 60 6 16.0

O 208-240 60 3 3 7 20 12 4.0 64 70 4 25.0

X 200-240 50/60 1/3 2/3 9 20 12 4.0 N/A N/A N/A N/A

Variable-Speed Models

N 440-480 50/60 3 3 4 15 14 2.5 42 50 8 10.0

P 380-415 50/60 3 3 5 15 14 2.5 37 40 8 10.0

Q 200-240 50/60 3 3 6 15 14 2.5 65 60 6 16.0

X 200-240 50/60 1/3 2/3 10 20 12 4.0 N/A N/A N/A N/A

NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.

Tabl e 14

Installation

F232135

Electrical Specifications

80 Pound Capacity Models

Voltage Designation Standard Electric Heat

Code

Voltage

Cycle

Phase

Wire

Full Load

Amps

Circuit

Breaker

AWG

Full Load

Amps

Circuit

Breaker

AWG

Variable-Speed Models

N 440 – 480 50/60 3 3 4.5 15 14 2.5 42 45 8 10

P 380 – 415 50/60 3 3 4.5 15 14 2.5 37 40 8 10

Q 200 – 240 50/60 3 3 12.4 20 12 4 87.4 90 2 35

NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.

Tabl e 15

Electrical Specifications

125 Pound Capacity Models

Voltage Designation Standard Electric Heat

Code

Voltage

Cycle

Phase

Wire

Full Load

Amps

Circuit

Breaker

AWG

Full Load

Amps

Circuit

Breaker

AWG

Variable-Speed Models

N 440 – 480 50/60 3 3 5.1 15 14 2.5 N/A

P 380 – 415 50/60 3 3 5.1 15 14 2.5 N/A

Q 200 – 240 50/60 3 3 7.9 25 10 6 N/A

NOTE: Wire sizes shown are for copper, THHN, 90° conductor per NEC article 310.

Tabl e 16

Installation

F232135

Troubleshooting

If machine fails to operate after power is connected,

proceed as follows:

1. Disconnect power.

2. Unlock and raise top cover.

3. Check circuit fuse.

For mechanical timer, P-computer and

S-computer models, control circuit fuse is located

on center brace.

For EDC and V-computer models, dual control

circuit fuses (one primary, one secondary) are in

control module. A decal identifies fuse(s) and

provides fuse-rating appropriate to that specific

model.

For NetMaster models, circuit fuses are located

on side of control box.

For A-control and B-control models, circuit fuses

are located on the output board.

4. If control circuit fuse has blown, replace with

fuse of appropriate rating as identified by decal.

IMPORTANT: Call a qualified electrician if

replacement fuse blows.

Steam Requirements

(Steam Heat Option Only)

For machines equipped with optional steam heat,

install piping in accordance with approved commercial

steam practices. Steam requirements are shown in

Table 17.

IMPORTANT: Failure to install the customer

supplied steam filter may void the warranty.

Steam Supply Information

Steam inlet

connection size

18 – 80 pound 1/2

in. (13 mm)

125 pound 3/4

in. (19 mm)

Number of steam inlets 1

Recommended pressure 30 – 80 psi

(2.0 – 5.4 bar)

Maximum pressure 80 psi

(5.4 bar)

Table 17

Hot Surfaces. Will cause severe burns.

Turn steam off and allow steam pipes,

connections and components to cool

before touching.

W505

WARNING

Installation

F232135

Supply Dispensing

(OPL Machines Only)

IMPORTANT: Undiluted chemical dripping can

damage the machine. All chemical injection supply

dispenser pumps and dispenser tubing should be

mounted below the washer’s injection point. Loops

do not prevent drips if these instructions are not

followed.

IMPORTANT: Failure to follow these instructions

could damage the machine and void the warranty.

Connection of External Liquid Supplies

18 – 80 Pound OPL Models

1. Facing the rear of the machine, locate the

1-1/2 inch (38 mm) opening found at the upper

right-hand side of the valve panel. Refer to

Figure 31.

Figure 31

2. Gather external supply hoses and pull through

opening.

3. Locate the 4 capped nozzles on the rear of the

liquid supply dispenser and remove caps. Refer

to Figure 32.

Supply Dispensing

18 – 80 125

Number of dry supply

compartments

30 or 5

(optional)

Number of liquid supply

connections (OPL only)

Liquid supply connection size 5/16

in.

(8 mm)

5/8 in.

(15.9 mm)

Dangerous Chemicals. May damage eyes

and skin. Wear eye and hand protection

when handling chemicals; always avoid

direct contact with raw chemicals. Read

the manufacturer’s directions for

accidental contact before handling

chemicals. Ensure an eye-rinse facility

and an emergency shower are within easy

reach. Check at regular intervals for

chemical leaks.

W363

WARNING

CHM2002N

1 External Supply Hose Opening

CHM2002N

C VALVE PANEL – REAR VIEW

Installation

F232135

Figure 32

4. Connect hoses to nozzles by pushing each hose

over nozzle lip. Hoses should fit snugly onto

nozzles and then secured with proper clamps.

NOTE: Do not attempt to make chemical injection

supply pump electrical connections to points other

than those provided specifically for that purpose by

the factory.

Machines connected to 200VAC provide L1 and L2

fused outputs rated at 3 amps which may be used to

power 208 – 240VAC supply pumps.

Machines connected to 400VAC do not provide L1 and

L2 outputs. An external power source must be

provided to power the chemical supply pump.

Do not use L1 or L2 with the common line to deliver

120VAC to chemical injection supply pumps if the

machine is equipped with a control transformer.

Consult the supply vendor instructions for operational

details about supply injections.

125 Pound OPL Models

(With Optional Dispenser)

Refer to Figure 33 and Figure 34.

1. Remove plugs from base. Plugs are assembled

inside tubing ring.

2. Install strain reliefs included in seal nut.

3. Insert tubes through base. Do not remove dry

supply cups. Tube should extend into plastic cup,

with exception of softener tube, which should be

routed to outside of cup.

4. Tighten seal nut to prevent tubing from escaping

assembly.

U149M

Nozzles:

1 Detergent

2 Bleach

3 Sour

4 Soft

5 Speciality

U149M

3 AND 4

Dangerous Voltages. Will cause damage

to the machine and microprocessor. Do

not attempt to obtain 110VAC by using L1

or L2 with the common. Do not use a

240VAC power wire in the washer-

extractor and an earth ground to obtain

110VAC.

W365

CAUTION

Installation

F232135

Terminals SUPPLY 1 through SUPPLY 5 provide

120VAC or 240VAC fused at 500mA. Refer to decal at

external supply terminal strip to determine whether

washer-extractor provides 120VAC or 240VAC. These

terminals may be used to provide signals to chemical

injection supply system but must not be used to

provide power to actual pump.

IMPORTANT: Increasing fuse rating may cause

damage to washer-extractor’s circuitry.

IMPORTANT: Any injection system pump that

requires 110VAC must be powered by a separate

external power source.

Consult chemical injection supply system instructions

for operational details.

Figure 33

Figure 34

P048I

1 Strain Relief for Liquid Chemical Supply

Lines

2 Supply Dispenser Lid

3 Dry Supply Cups

4 Dry Supply Insert

5 Four Way Water Valve

6 Supply Dispenser

P048I

DESIGNS 1-4

CHM2001N

1 Strain Relief for Liquid Chemical Supply

Lines

2 Supply Dispenser Lid

3 Dry Supply Insert

4 Dry Supply Cups

5 Four Way Water Valve

6 Supply Dispenser

PHM2001N

DESIGN 6

Installation

F232135

Control Function Test

1. The machine should be cleaned after the

installation is complete. A function test should

then be executed on the unloaded machine.

2. Check the power supply for correct voltage,

phase, and cycles to be certain they are correct

for the machine.

3. Open manual shut-off valves to the machine.

4. Turn on electric power.

5. Check the door interlock before starting

operation:

a. Open the loading door.

For coin-operated machines, press the round

button on the door handle and turn the door

handle downward.

For machines intended for use in on-premises

laundries, press and hold the door-unlock

button on the left side of the control panel.

Press the round button on the door handle and

turn the door handle downward.

b. Attempt to start the machine with the door

open. The machine should not start with the

door open.

c. Close the door without locking it and attempt

to start the machine. The machine should not

start with the door unlocked.

d. Close and lock the door and start a cycle.

Attempt to open the door while the cycle is in

progress. The door should not open.

If the door lock and interlock are not functioning

properly, call a service technician.

6. Run a complete cycle, checking operation of

water inlet valves, drain, and extract functions.

7. Check that cylinder rotation is counterclockwise

in the extract step. If rotation is not

counterclockwise in the extract step, disconnect

power. For variable-speed models, have a

qualified electrician reverse any two motor leads

at the AC drive terminal block (terminals U, V,

and W). For 2 speed models, have a qualified

electrician use the wiring diagram included with

the machine to determine which input power

leads should be switched.

Instalación

www.comlaundry.com

Lavadoras

extractoras

Montaje fijo en gabinete

Consulte la página 61 para la identificación de

modelos

CHM166C

Pieza No. F232135R6

Junio 2005

Guarde estas instrucciones para referencia en el futuro.

(Si esta máquina cambia de dueño, asegúrese de que este manual vaya con la misma).

Reservados todos los derechos. Ninguna sección del presente manual puede reproducirse o transmitirse en forma

alguna o a través de ningún medio sin el consentimiento expreso por escrito del editor.

F232135 (SP)

Tabla de

contenido

Información de seguridad.................................................................. 59

Explicación de los Mensajes de seguridad ........................................... 59

Instrucciones importantes de seguridad................................................ 59

Introducción ........................................................................................ 61

Identificación de modelos..................................................................... 61

Inspección de entrega ........................................................................... 62

Posición de la placa de identificación................................................... 62

Piezas de recambio ............................................................................... 64

Servicio al cliente ................................................................................. 64

Retirar después del envío (modelos OPL solamente)........................... 64

Especificaciones y dimensiones.......................................................... 65

Ajuste de separación para el interruptor de vibración

(modelos de velocidad variable y modelos de velocidad fija) ....... 68

Instalación ........................................................................................... 79

Dimensiones de separación................................................................... 79

Cimientos de la máquina ...................................................................... 80

Anclaje de la máquina .......................................................................... 83

Instalación directa al piso acabado .................................................. 83

Números de pieza de la plantilla de pernos de montaje

(sin bastidor de base elevada)............................................................. 86

Ubicaciones de los orificios de los pernos de montaje

(sin bastidores de base elevada) ......................................................... 87

Ubicaciones de los orificios de los pernos de montaje

(sin bastidores de base elevada). ........................................................ 88

Ubicaciones de los orificios de los pernos de montaje

(con bastidores de base elevada) ........................................................ 89

Ubicaciones de los orificios de los pernos de montaje

(con bastidores de base elevada) ........................................................ 90

Instalación de bastidor en base elevada ........................................... 91

Instalación en cimiento de concreto................................................. 93

Conexión de drenaje ............................................................................. 96

Requisitos de la conexión de agua........................................................ 98

Requisitos de la instalación eléctrica.................................................... 99

Requisitos de voltaje de entrada ...................................................... 99

Disyuntores ...................................................................................... 99

Especificaciones de conexión .......................................................... 100

Puesta a tierra................................................................................... 100

Dispositivo de adición de fases........................................................ 100

Protector de sobrecarga térmica....................................................... 100

Localización y resolución de problemas.......................................... 106

Requisitos de vapor (opción de calentamiento de vapor solamente).... 106

Distribución de suministro (máquinas OPL solamente)....................... 107

Conexión de suministro de líquido externo ..................................... 107

Prueba de función de control ................................................................ 110

F232135 (SP)

Notas

F232135 (SP)

Información de seguridad

Explicación de los Mensajes de

seguridad

Las medidas de precaución (“PELIGRO,”

“ADVERTENCIA” y “PRECAUCIÓN”), seguidas por

instrucciones específicas, se encuentran en este

manual y en las calcomanías de la máquina. Estas

precauciones sirven para proteger la seguridad del

operador, usuario y aquellas personas responsables del

mantenimiento de dicha máquina.

Otras medidas de precaución tales como

(“IMPORTANTE” y “NOTA”) van seguidas de

instrucciones específicas.

IMPORTANTE: La palabra “IMPORTANTE” se

utiliza para informar al lector acerca de

procedimientos específicos donde se producirán

daños menores en caso de no seguirse el

procedimiento.

NOTA: La palabra “NOTA” se utiliza para

comunicar información de instalación, operación,

mantenimiento o servicio que sea importante pero

que no se relacione con un riesgo.

Instrucciones importantes de

seguridad

1. Lea todas las instrucciones antes de usar la

lavadora.

2. Consulte las INSTRUCCIONES DE PUESTA A

TIERRA en el manual de INSTALACIÓN para

conectar bien a tierra la lavadora.

3. No lave telas que anteriormente se hayan

limpiado, lavado, puesto en remojo o manchado

de gasolina, kerosèn, ceras, aceite de cocina,

disolventes de tintorería u otras sustancias

inflamables o explosivas, ya que desprenden

vapores que pueden inflamarse o estallar.

4. No añada gasolina, disolventes de tintorería u

otras sustancias inflamables o explosivas al agua

de lavado. Estas sustancias desprenden vapores

que pueden inflamarse o estallar.

5. En ciertas condiciones, se puede desprender

hidrógeno en un sistema de agua caliente que no

se haya usado durante dos semanas o más. EL

HIDRÓGENO ES EXPLOSIVO. Si no se ha

usado el sistema de agua caliente durante el

período mencionado, abra todas las llaves de

agua caliente y deje correr el agua por cada una

durante varios minutos antes de usar una lavadora

o combinación de lavadora y secadora. Esto

desprenderá el hidrógeno que pueda estar

acumulado. Este gas es inflamable, por lo que no

se debe fumar ni usar una llama abierta durante

este tiempo.

6. No permita que haya niños jugando en la

lavadora o en sus alrededores. Es necesario

supervisar constantemente a los niños cuando se

utilice la lavadora en su presencia. Ésta es una

regla de seguridad pertinente a todos los aparatos.

PELIGRO indica la presencia de un riesgo

que ocasionará lesiones personales

graves, mortales o daños materiales

importantes en caso de hacerse caso

PELIGRO

ADVERTENCIA indica la presencia de un

riesgo que ocasionará lesiones

personales graves, mortales o daños

materiales importantes en caso de

ADVERTENCIA

PRECAUCIÓN indica la presencia de un

riesgo que ocasionará lesiones

personales menores o daños materiales

en caso de hacerse caso omiso de la

PRECAUCIÓN

Para reducir el riesgo de incendios,

electrocución y lesiones graves o mortales

cuando use la lavadora, tome estas

precauciones básicas:

W023SR1

ADVERTENCIA

Información de seguridad

F232135 (SP)

7. Antes de poner la lavadora fuera de servicio o

desecharla, quite la puerta del compartimento de

lavado.

8. No introduzca las manos en la lavadora si el

cilindro de lavado se encuentra girando.

9. No instale ni guarde la lavadora en lugares donde

quede expuesta al agua o a las inclemencias del

tiempo.

10. No juegue con los controles.

11. No repare ni reemplace ninguna pieza de la

lavadora, ni intente ningún servicio a menos que

se recomiende específicamente en las

instrucciones de mantenimiento del usuario o en

instrucciones publicadas de reparación del

usuario que pueda comprender y siempre que

tenga la habilidad de hacerlo.

12. Para reducir el riesgo de electrocución o

incendio, NO use un cordón de extensión ni un

adaptador para conectar la lavadora a la fuente de

energía eléctrica.

13. Use la lavadora sólo en la aplicación para la que

ha sido diseñada, lavar telas.

14. Desconecte SIEMPRE la lavadora de la fuente de

alimentación eléctrica antes tratar de efectuar

cualquier servicio. Desconecte el cordón de

alimentación agarrando el enchufe, no el cordón.

15. Instale la lavadora según estas

INSTRUCCIONES DE INSTALACIÓN. Todas

las conexiones de agua, drenaje, eléctricas y de

puesta a tierra deben cumplir con los códigos

locales y ser realizadas por personal autorizado

cuando sea necesario.

16. Para reducir el riesgo de incendios, no ponga en

la lavadora telas que puedan tener restos de

sustancias inflamables tales como aceite vegetal,

aceite de cocinar, aceite de máquinas, productos

químicos inflamables, diluyentes, etc. o cualquier

artículo que contenga cera o productos químicos,

como los presentes en fregonas y trapos de

limpieza. Estas sustancias inflamables pueden

hacer que la tela se prenda fuego por sí misma.

17. No utilice productos suavizantes de telas ni

productos que eliminen la electricidad estática, a

menos que lo recomiende el fabricante de dichos

productos.

18. Mantenga la lavadora en buenas condiciones. Los

golpes o caídas de la lavadora pueden dañar los

dispositivos de seguridad. Si ocurre esto, pida a

una persona de servicio cualificada que

inspeccione la lavadora.

19. Sustituya los cordones de alimentación

desgastados y los enchufes aflojados.

20. Asegúrese de que las conexiones de agua tengan

una válvula de cierre y las conexiones de la

manguera de llenado estén apretadas. CIERRE

las válvulas de cierre al final de cada jornada de

lavado.

21. La puerta de carga DEBE ESTAR CERRADA

siempre que la lavadora se llene, se agite o gire a

gran velocidad. NO ponga en derivación el

interruptor de la puerta de carga dejando que la

lavadora funcione con la puerta de carga abierta.

22. Lea y siga siempre las instrucciones del

fabricante de los paquetes de productos de

limpieza para ropa. Respete todas las

advertencias y precauciones. Para reducir el

riesgo de envenenamiento o quemaduras

causadas por productos químicos, manténgalos

fuera del alcance de los niños en todo momento

(preferentemente, en un armario cerrado con

llave).

23. Siga siempre las instrucciones de cuidado de las

telas proporcionadas por el fabricante textil.

24. No opere nunca la lavadora si se han quitado los

protectores o los paneles.

25. NO opere la lavadora con piezas que falten o que

estén rotas.

26. NO ponga en derivación ningún dispositivo de

seguridad.

27. Si la instalación, el mantenimiento o la operación

de esta lavadora no se realiza según las

instrucciones del fabricante, se pueden producir

lesiones graves, mortales o daños materiales.

NOTA: Una carga inferior a lo normal puede

provocar condiciones de falta de equilibrio que

pueden acortar la vida de la máquina.

NOTA: Las ADVERTENCIAS y las

INSTRUCCIONES DE SEGURIDAD

IMPORTANTES que aparecen en este manual no

intentan cubrir todas las condiciones y situaciones

posibles que puedan ocurrir. Hay que hacer uso del

sentido común, tomar precauciones y tener cuidado

al instalar, mantener u operar la lavadora.

Los problemas o condiciones que no se entiendan

deberán hacerse saber al concesionario, distribuidor,

agente de servicio o fabricante.

F232135 (SP)

Introducción

Identificación de modelos

La información de este manual corresponde a estos

modelos: