Minka-Aire F745-DK Instrucciones de operación

Marca: Minka-Aire

Modelo: F745-DK

Categoría: Ventiladores domésticos

Tipo: Instrucciones de operación

Este manual también es adecuado para

CERTIFICATE

Sabot

Manual design and all elements of manual design are protected by U.S. Federal and/or State Law, including Patent, Trademark and/or Copyright laws.

The Minka-Aire® warranty is for one (1) year from the date of purchase from an authorized Minka-Aire® dealer.

This warranty is only valid to the original purchaser or user against all defects in material and workmanship light bulbs (

excluded for one full year. Additionally, Minka-Aire® warrants the motor only for the lifetime of the Minka Aire ceiling ) (1)

fan excluding wall controls and electrical components , to the original purchaser or user. ( )

* The warranty is voided with the use of any non- Minka-Aire®electrical devices, e.g., wall controls or electrical dimmer switches, etc…

* The warranty is void once the original purchaser or user ceases to own the fan or the fan is moved from its original point of installation.

* The warranty is void with the use of any hanger bracket (non-Minka Aire or non-fan specific other than the hanger bracket supplied )

& installed

with this specific fan.

Date Purchased Store Purchased Model Number Serial Number

F745

Warranty Service Information

To obtain warranty service during the warranty period, the purchaser should return the fan with the sales receipt to the original place of

purchase. The authorized Minka-Aire® dealer, at its sole discretion, will either repair or replace the fan after verifying the legitimacy of the warranty

claim. Replacement is subject to availability of the same model. If the model is unavailable it will be replaced by one of equal value. This is a limited

warranty; the original purchaser or user is responsible for the cost of removal and reinstallation of repaired or replacement product.

To obtain the name of the Minka-Aire® authorized dealer nearest you call the Minka-Aire® customer care department at 1-800-307-3267, or

contact Minka-Aire® through www.minkagroup.net and select FAQ to answer any questions or if you require additional assistance submit the question

form found there.

CONTENTS

FINISHING THE INSTALLATION

OPERATING THE REMOTE CONTROL/WALL CONTROL

CARE OF YOUR FAN

TROUBLESHOOTING

SPECIFICATIONS

SAFETY RULES

PACKAGE CONTENTS

INSTALLING THE FAN

BLADE INSTALLATION

HANGING THE FAN

ELECTRICAL CONNECTIONS

........................................................

...............

...............................................................................

...........................................................................

...................................................................................

...................................................

......................................

...................................

..........................................

..........................

SAFETY RULES

2. Be cautious! Read all instructions and safety information before installing your new fan. Review accompanying assembly diagrams.

3. Make sure that all electrical connections comply with local codes, ordinance, or National Electrical Codes. Hire a qualified electrician or

consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.

4. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet

from the floor and 18 inches from the top of the blades to the wall.

5. If you are mounting the fan to a ceiling fan outlet box, use a U.L Listed metal octagonal outlet box marked"Acceptable For Fan Support".

Secure the box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at

least 50 pounds). Do not use a plastic box.

6. Caution: To reduce the risk of injury use only the screws provided with the outlet box in conjunction with the lock washers provided with

the fan.

7. If you are mounting the fan to a joist, make sure it is able to support the moving weight of the fan (at least 50 pounds).

8. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.

9. Do not insert anything into the fan blades while the fan is operating.

10. Turn the fan off and wait for the blades to stop completely before performing any maintenance or cleaning.

Before you begin installing the fan, shut power off the circuit breaker of the fuse box.

NOTE: The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and

situations that may occur. It must be understood that common sense, caution and care are factors which cannot be built into

this product. These factors must be supplied by the person(s) installing, caring for and operating the unit.

NOTE: READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF FIRE,ELECTRIC SHOCK OR OTHER PERSONAL INJURY, MOUNT FAN ONLY TO A U.L LISTED OUTLET BOX OR SUPPORTING

SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX IN CONJUCTION WITH THE

LOCK WASHERS PROVIDED WITH THE FAN. MOST OUTLET BOXS COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURES ARE NOT

ACCEPTABLE FOR FAN SUPPORT AND NEED TO BE REPLACED. CONSULT A QUALIFIDE ELECTRICIAN IF IN DOUBT.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE HOLDERS WHILE INSTALLING BALANCING THE BLADES OR CLEANING

THE FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.

TO REDUCE THE RISK OF FIRE OR ELECTRONIC SHOCK, THIS FAN ONLY CAN USE DL-4510 REMOTE CONTROL ONLY.

ATTENTION: The Energy Policy Act of 2005 requires this fan to be equipped with a 190 watt limiting device, If lamping exceeds

190watts, the ceiling fan’s light kit will shut off automatically.

PACKAGE CONTENTS

1. Fan blades(5)

2. Hanger bracket

3. Canopy

4. Canopy cover

5. Coupling cover

6. Standard downrod assembly(6")

Minimum-length downrod(3.5")

7. Fan motor/housing assembly

8. Transmitter + holder + 2mounting

screws + A23 12 volt battery

9. Power cord

10. Balancing kit

A. Mounting hardware:

Wire nuts(3)

#8x3/4”Machine screws (2)

#10x1.5Wood screws (2)

4mm Star washers (2)

Metal washers (2)

Lock washers (2)

B. Blade attachment hardware:

3/16“x8mm Screws(16)

Fiber washers (16)

Unpack your fan and check the contents. You should have the following items:

INSTALLING THE FAN

MOUNTING OPTIONS

If there isn't an existing mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building structure. Use appropriate fasteners and

building materials. The outlet box and its support must be able to fully support the moving

weight of the fan (at least 50 lbs.).Use a UL listed metal outlet box.

Do not use a plastic outlet box.

Figure1,2 and 3 are examples of different ways to mount the outlet box.

Note: You may need a longer downrod to maintain proper blade clearance when installing on

a steep, sloped ceiling. Longer downrods are available from your Minka-Aire dealer.

To hang your fan where there is an existing fixture but no ceiling joist, you may need to

install a hanger bar as shown in Fig.4(available at your Minka Aire dealer or local hardware store)

Tools Required: Philips screw driver, slotted screw driver, step-ladder, wire cutters, electrical tape.

FIG. 1

CROSS BRACE

CEILING

JOIST

CEILING

jOIST

OUTLET

BOX

FIG. 2

PARALLEL

WOOD BRACE

(MIN. 2’’ THICK)

OUTLET

BOX

CEILING

JOIST OR

CROSS BRACE

FIG. 3

ANGLED CEILING

MAXIMUM 18°ANGLE

PROVIDE

STRONG

SUPPORT

RECESSED

OUTLET

BOX

HANGER

OPENING

must be

FACING

UPSIDE

FIG. 4

CEILING

JOIST

OUTLET BOX

HANGER BAR

(OPTIONAL)

HANGER

BRACKET

BLADE INSTALLATION

Step 1.

removing five screws.(Fig.5)

Step 2.Insert the blades through the slots on the fan motor

assembly. Attach the fan blades to the fan motor assembly using

the blade screws and fiber washer and tighten them securely.

(Fig. 6)

Step 3. Install the up housing to the fan motor assembly with the

screws previously removed.

Remove the up housing from the fan motor assembly by

Blade

Fiber Washer

Screw

Fig. 5

Fig. 6

Screws

Up housing

Fan motor

assembly

Fan motor

assembly

HANGING THE FAN

WARNING: All of the parts, hardware and components such as the

hanger bracket and hanger ball have been provided for your safety and

the proper installation of your new ceiling fan. The use of other

parts,hardware or components not supplied by Minka Aire with the fan

will void the Minka Aire Warranty.

REMEMBER to turn off the power. Follow the steps below to hang your

fan properly:

Step 2.Lossen the two set screws and remove the hitch pin and lock pin

from the top coupling of the motor assembly.(Fig 8)

Step 3.Remove hanger ball from downrod assembly by loosening set

screw,removing the cross pin, and sliding ball off rod.(Fig 9)

Step 1.Secure the hanger bracket to the ceiling outlet box using screws

and washers included with mounting hardware.(Fig.7)

Step 4.Carefully feed fan wires up through the downrod(Fig 10).

Thread the rod into the coupling, next line up holes and replace lock

pin and hitch pin. Tighten set screws.

Step 6. Now lift motor assembly into position and place hanger ball

into hanger bracket. Rotate until the check groove has dropped into

the registration slot and seats firmly.(Fig 12)Rod should not rotate

if this is done correctly.

Step5.Slip coupling cover, canopy cover, and canopy onto downrod

(Fig.11).Carefully reinstall hanger ball onto rod being sure that cross

pin is in the correct position, set screws are tighten and wires are

not twisted.

Fig. 12

REGISTRATION

SLOT

Fig. 10

DOWNROD

SUPPLY

WIRES

Fig. 9

CROSS PIN

HANGER

BALL

DOWNROD

SET SCREW

Fig. 8

HITCH

LOCK

SET SCREWS

Fig. 7

OUTLET BOX

HANGER BRACKET

Fig. 11

LOCK PIN

CANOPY

COVER

DOWNROD

CANOPY

SCREWS

HITCH PIN

COUPLING

ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock be sure electricity is turned off at the main fuse or

breaker box before wiring.

NOTE: The Aire Control® System for this DC motor fans is equipped with a learning frequency

function which has 32 code combinations to prevent potential interference from other remote

units.

The frequency on your Receiver and Transmitter units have been preset at the factory. (Fig. 13)

No frequency change is necessary, should you desire to install another Minka Aire DC motor fan

within the same home or area with a separate frequency code please see the "frequency

interference" troubleshooting section of this instruction manual to learn how to change the

frequency.

Step 1. Motor to House Supply Wires Electrical Connections: Firmly snap the wire connection

plugs from the motor and the power cord together. (Fig. 14)

Connect the WHITE wire (Neutral) from the outlet box to the WHITE wire marked "AC in N" in the

power cord. Connect the BLACK wire (Hot) from the outlet box to the BLACK wire marked "AC in

L" in the power cord. Secure all wire connections with the plastic wire nuts provided. (Fig. 15)

Fig. 13

Step 2. If your outlet box has a GROUND wire

(Green or Bare Copper) connect this wire to the

Hanger Ball and Hanger Bracket Ground wires. If

your outlet box does not have a Ground Wire,

then connect the Hanger Ball and Hanger

Bracket Ground Wires together. Secure wire

connection with the plastic wire nut provided.

(Fig. 15)

After all splices are made, check to make sure

there are no loose strands. As an additional

precaution we suggest to secure the plastic wire

connectors to the wires with electrical tape.

Fig. 15

Connection plug

Power cord

Fig. 14

FINISHING THE INSTALLATION

Fig. 16

OUTLET BOX

HANGER

BRACKET

HANGER

BALL

CANOPY

COVER

″

Step 1. Tuck connections neatly into ceiling outlet box.

Step 2. Remove one screw from the hanger bracket and loosen the other screw

around 1/4” .

Step 3. Align the canopy up to ceiling and over the loose screw. Place the canopy into

key hole and rotate canopy clockwise. (Figure 16)

Step 4. Secure the canopy by use previous removed screw.

Step 5. Place the canopy cover to the canopy and rotate canopy cover clockwise until

it is locked into right position. (Figure 16)

OPERATING THE REMOTE CONTROL/WALL CONTROL

cool

Note: The auto learning function will only

mandate within 60 seconds when turning the

fan’s AC power ON.

1. Select desired frequency from the back of

transmitter.

2. Press the transmitter’s “Off” button, and

hold the “Off” button for over 10 seconds.

Once the receiver has detected the frequency,

the down light of your fan if applicable will

blink twice. (There is no indication if your fan

is not equipped with a light).

Note: The learning frequency function will

continue to retain the last set frequency even

when the AC power is shut off.

The DC motor has a built in safety feature

against obstruction during operation, if the fan motor

senses a obstruction for 60 seconds or more it will get

locked and will not rotate until the obstruction has

been removed and the power has been disconnected for

5 seconds.

2. Over 60W protection: When the receiver detects

motor power consumption which is greater than 60W,

the receiver’s power will stop and operation will be

immediately discontinued. If you want to re-start the

fan, Please remove obstacles and disconnect the power

by turning off the circuit breaker . And turn the power

on after 5 seconds.

3. “DIMMER” and “ON/OFF” dip switch:

The “DIMMER” selection is the light dimmable selection

and is to be used with all bulbs except for CFL bulbs. The

“ON/OFF” selection is For CFL bulbs.

Fig. 17

Fig. 19Fig. 18

Speed settings for warm or cold weather depend on

factors such as room size, ceiling height and number

of fans.

NOTE: to change the direction of the rotation of the

blades the fan must be in operation mode.

Warm Weather (forward)

A DOWNWARD airflow creates a cooling effect as

shown in Figure 18. This allows you to set your air

conditioner on a warmer setting without affecting

your comfort.

Cool Weather (Reverse)

An UPWARD airflow moves warmer air off the

ceiling area as shown in Figure 19. This allows you

to set your heating unit on a cooler setting without

affecting your comfort.

SUMMER OPERATION

COUNTER CLOCKWISE

WINTER OPERATION

CLOCKWISE

CARE OF YOUR FAN

SYMPTOM

Fan will not start

SOLUTION

Check to make sure the wall switch is turned on.

Check circuit fuses or breakers.

Caution! Make sure the power is turned off before performing the

following steps.

Remove canopy and check wire connections.

Check wall control transmitter connections(if applicable).

Note: Fan must be installed at a maximum distance of 40 feet from

the transmitting unit for proper signal transmission between the

transmitting unit and the fan’s receiving unit.

SYMPTOM

Fan Sounds Noisy

SOLUTION

Allow a 24 - hour “ break in ” period. Most noises associated

with a new fan will go away during this time.

Make sure the screws that attach the fan blade holder to the

motor hub is tight.

Make sure outlet box is secured to building structure, if

necessary use the wood screws provided to further secure

outlet box to joist.

Make sure hanger bracket is secure to the outlet box, screws are

tight.

TROUBLESHOOTING

SYMPTOM

Fan Wobble

SOLUTION

NOTE: All blade sets are grouped by weight. Because wood and plastic

blades vary in density, the fan may wobble even though blades are

matched.

Make sure outlet box is secured to building structure, if necessary use

the wood screws provided to further secure outlet box to joist.

Make sure hanger bracket is secure to the outlet box, screws are tight.

If a Balancing kit is provided follow the instructions included with the

balancing kit to help correct any excessive wobble.

SYMPTOM

Lights shut off and will not come back on

SOLUTION

This unit is equipped with a wattage limiting device. Lamping in

excess of 190 watts will disable your ceiling fan’s light kit. To reset

your light kit you must turn the power off and re lamp, keeping the

wattage under 190 watts.

SYMPTOM

Fans/Light Turn on and Off Unexpectedly

SOLUTION

This is caused by interference. Please see “frequency interference” for

step to charge the frequency.

SYMPTOM

Frequency Interference

SOLUTION

1.Turn the power off to your ceiling fan.

2.Please use a small size tool to change the frequency settings on the control system.

3.Returm power to the unit.

Note: After the AC power is on, do not press any other button on the transmitter before pressing the “Stop” button, doing so will cause the procedure to fail.

4.Within 60 seconds of turning the fan’s AC power ON. Press the transmitter’s “Stop” button and hold the “Stop” button for 10 seconds.

5.Once the receiver has detected the set frequency, the down light of your fan if applicable will blink twice.(there is no indication if your fan is not equipped

with a light).

6.The receiver has now learn the frequency which has been selected on the transmitter. After completing the steps above, you should be able to operate the

ceiling fan and light. If the fan is not responding to the transmitter. please turn the power off to the receiver, and repeat the process.

SPECIFICATIONS

These are typical readings. Your actual fan may vary.

They do not include amps and wattage used by

the light (s).

For any additional information about your

Minka Aire Ceiling fan, please write to:

52"

0.043

0.07

0.11

0.18

0.27

0.42

2.7

4.6

7.6

12.7

20.0

33.0

122

145

173

1635

2566

3396

4221

4918

5779

5.72

kgs

6.66

kgs

1.175’

1635

2566

3396

4221

4918

5779

2.7

4.6

7.6

12.7

20.0

33.0

606

558

447

332

246

175

Sabot

MANUAL DE INSTRUCCIONES CERTIFICADO DE GARANTIA

Diseño del manual y todos los elementos del diseño de manual están protegidos por EE.UU. y / o federales del Estado de Derecho, incluyendo

patentes, marcas y / o derechos de autor.

La garantía de Minka-Aire® es de un año a partir de la fecha de compra de un distribuidor autorizado de (1)

Minka-Aire®. Esta garant a sólo es válida para el comprador original o al usuario contra cualquier defecto de material y í

mano de obra focos no incluidos por año completo. Adem s, Minka-Aire® garantiza por vida el motor del ventilador ( ) (1) á

de techo únicamente por vida con exclusi n de los controles de la pared y componentes el ctricos , al comprador ( ó é )

original o al usuario.

* La garant a queda anulada con el uso de los equipos el ctricos que no son de Minka-Aire®, controles de ejemplo, interruptoresí é de pared o

interruptores eléctricos regulador, etc ...

* La garant a no es v lida una vez que el comprador original o el usuario deja de poseer el ventilador o el ventilador se mueveí á

desde su punto de

instalaci n original. ó

* La garant a es vac a con demandar de cualquier soporte de suspensi n (non-Minka Aire o no abanico espec fico) adem s del sopoí í ó í á

rte de suspensi n ó

suministrado e instalado con este abanico especificamente.

Fecha de Compra Tienda Donde Lo Compro Num. De Modelo Num. De Serie

F745

Para obtener servicio de garant a durante el per odo de garant a, el comprador debe devolver el ventilador con el recií í í bo de compra al lugar

original de compra. El distribuidor autorizado de Minka-Aire®, a su discreci n, puede reparar o reemplazar el ventilador despuó és de verificar la

legitimidad de la reclamaci n de garant a. Reemplazo est sujeto a la disponibilidad del mismo modelo. Si el modelo no est disó í á á

ponible ser , á

sustituido por uno de igual valor. Esta es de una garant a limitada, el comprador original o usuario es responsable por el costí o de quitar y reinstalar

del producto reparado o reemplazado.

Informaci n de Servicio de Garant aó í

Para obtener el nombre del distribuidor Minka-Aire® autorizado m s cercano se llama a Minka-Aire® departamento de atená

ci n al cliente al ó

1-800-307-3267, ó é o p ngase en contacto Minka-Aire® a trav s de www.minkagroup.net y seleccione FAQ para responder a cualquier pregunta, o si

necesita ayuda adicional, envie el formulario de preguntas que encontró alli.

LA SEGURIDAD PRIMERO

CONTENIDO DEL PAQUETE

COMENZANDO LA INSTALACION

INSTALACION DE LAS ASPAS

COLGANDO EL VENTILADOR

CONEXIONES ELECTRICAS

.....................................................

OPERACION DEL CONTROL REMOTO O EL TRANSMISOR DE PARED

......

MANTENIMIENTO DE SU VENTILADOR

.........................................

SOLUCION DE PROBLEMAS

...............................................................

ESPECIFICACIONES

.............................................................................

...............................

...........................

...............

........................

.............................

TERMINANDO LA INSTALACION

10.Apague el ventilador y espere a que las aspas se detengan por completo antes de realizar cualquier tarea de mantenimiento o limpieza.

PARA REDUCIR EL RIESGO DE INCENDIO O DESCARGA ELÉCTRICA, ESTE VENTILADOR SÓLO SE PUEDE UTILIZAR DL-4510 CONTROL

REMOTO SOLAMENTE.

CONTENIDOS EN PAQUETE

Desempaquete su ventilador y verifique los contenidos. Usted debe tener los siguientes elementos:

1. Aspa de ventilador

(

2. Soporte de suspensión

3. Dosel

4. Cubierta de dosel

5. Cubierta de acoplamiento

6. Asamblea de barra estándar (6 ")

Barra más corta (3.5 ")

7. Motor de ventilador/asamblea de

caja protectora

8. Transmisor con portatransmisores

+ 2 tornillos de montaje + bateria

A23 de 12 voltios

9. Cable de alimentación

10.Juego de Equilibrio

A. Hardware de montaje:

Tuercas de alambre (3)

#8x3/4” Tornillos de la máquina (2)

#10x1.5 Tornillos de madera (2)

Arandelas de seguridad (2)

Arandelas de estrella (2)

Arandelas de metálica (2)

B. Hardware para montaje de

accesorios de aspa:

Tornillos de 3/16“x8mm (16)

Arandelas de fibra (16)

INSTALACIÓN DE LAS ASPAS

Paso 1.

quitando los cinco tornillos.(Fig.5)

Paso 2.Inserte las aspas a través de las ranuras encima del conjunto

del motor del ventilador. Fije las hojas del ventilador en el

conjunto del motor del ventilador por utilizando los tornillos de

aspa y la arandela de fibra, entonces los aprieten fuertemente.

(Fig. 6)

Paso 3. Reinstale la carcasa

Quite la carcasa de la unidad del motor del ventilador

Fig. 5

Fig. 6

CARCASA

CONJUNTO DEL MOTOR

DEL VENTILADOR

ASPA

TORNILLOS

ARANDELAS

DE FIBRA

TORNILLOS

CONJUNTO DEL MOTOR

DEL VENTILADOR

CUBIERTA

DE DOSEL

Fig. 9 Fig. 10

Fig. 11

Fig. 12

CONEXIONES ELECTRICAS

RECORDAR: Apagar la energia electrica en el circuito principal o en la caja de fusibles.

NOTA: El Control de Aire® para los ventiladoeres de motor de corriente directa está equipado

con una función de aprendizaje de frecuencia que tiene 32 combinaciones de códigos para

evitar la posible interferencia de otras unidades de control remoto.

La frecuencia de su receptor y transmisor de las unidades han sido ajustados en la fábrica. (Fig.

13) No cambio de frecuencia es necesario, si usted desea instalar otro Minka Aire ventilador con

motor de corrienta directa dentro de la misma casa o en la misma área con un código de

frecuencia diferent por favor consulte la "interferencia de frecuencia" sección de solución de

problemas de este manual de instrucciones para aprender a cambiar la frecuencia.

Paso 1. Haga las conexiones de la caja de distribucion a el Receptor de la manera siguiente;

Se encajan las clavijas de conexión de cables.(Fig.14)

Conecte el Alambre blanco (neutral) de la caja de distribucion al alambre blanco marcado "AC in

N" del receptor. Conecte el Alambre Negro (corriente) de la caja de distribucion al alambre Negro

marcado "AC in L" del Receptor. Asegure las conexiones con los conectores de plastico proveidos.

(Fig. 15)

FRECUENCIA

Fig. 13

Paso 2. Si su caja de distribucion tiene un

alambre a tierra (verde o cobre) conectelo a los

alambres a tierra (verdes) de la Esfera de

Soporte y la Abrazadera de Montaje. Si su caja

de distribucion no tiene un alambre a tierra,

entonces unicamente conecte los dos alambres a

tierra de la Esfera de Soporte y la Abrazadera de

Montaje. Asegure la conexion con un conector

de plastico proveido. (Fig. 15)

Despues de terminar las conexiones del

alambrado, revise que no haiga hebras de

alambre sueltas. Como una precaucion mas,

sugerimos que asegure los conectores de

plastico a los alambres usando cinta aislante

electrica.

CONEXIÓN DE CABLES

CABLE DE ALIMENTACIÓN

Fig. 14 Fig. 15

FINALIZAR LA INSTALACIÓN

Paso 1. Hace conexión perfecta en la caja de salida del techo.

Paso 2. Quita un tornillo por el soporte colgante y afloje el tornillo contrario.

Paso 3. Alinea el dosel hacia arriba al techo,y sobre el tornillo suelto. Coloque el dosel en

el agujero clave y gira el dosel en sentido del horario. (Figura 16)

Paso 4. Asegúre el dosel usando el tornillo quitado anteriormente.

Paso 5. Coloque la cubierta de dosel por encima del dosel y girar la cubierta del dosel

en sentido el horario hasta que quede el la posición correcta. (Figura 16)

Fig. 16

CUBIERTA

DE DOSEL

Nota: La función de aprendizaje automático

sólo es dentro de los 60 segundos al encender

la corriente electrica al ventilador .

1. Seleccione la frecuencia deseada en la parte

posterior del transmisor.

2. Presione el botón "Off" del transmisor, y

mantenga presionado el botón "Off" durante

más de 10 segundos. Cuando el receptor ha

detectado la frecuencia, la luz inferior de su

ventilador se parpadeará dos veces si procede.

(No hay indicios si el ventilador no está

equipado con una luz).

Nota: La función de frecuencia de aprendizaje

continuará manteniendo la última frecuencia

ajustada, incluso si la fuente de alimentación

de CA está apagada.

1. El motor de corriente continua cuenta con

una caracteristica de seguridad contra la

durante la operación, si el motor del ventilador detecta

una obstrucción durante 60 segundos como mínimo,

será bloqueado y no girará hasta que la obstrucción

haya sido retirada y la potencia se haya desconectado

durante 5 segundos.

2. Protección contra más de 60W: Cuando el receptor

detecta el consumo de potencia del motor que es

superior a 60 W, la fuente de alimentación del receptor

se apagará y la operación se interrumpirá

inmediatamente. Si desea volver a encender el

ventilador, retire los obstáculos y desconecte la

alimentación apagando el disyuntor. Y encienda

después de 5 segundos.

3. Interruptor “DIMMER” y “ON/OFF”:

La selección “DIMMER” es la selección de luz atenuada y

se utiliza con todas las bombillas excepto bombillas

CFL. La selección “ON/OFF” es para las bombillas CFL.

obstrucción

Fig. 17

Fig. 19Fig. 18

La configuración de velocidad de aire caliente o frío depende

de factores como el tamaño de la habitación, la altura de

techo y el número de ventiladores.

NOTA: Espere a que se detengan el ventilador antes de

cambiar la configuración del interruptor deslizante.

Aire cálido (adelante)

Un flujo de aire hacia ABAJO crea un efecto refrescante como

se muestra en Figura 18. Eso le permite definir su

acondicionador de aire en una configuración más cálida sin

afectar a su comodidad.

Aire fresco (Reverso)

Un flujo de aire hacia ARRIBA mueve el aire caliente fuera de

la zona de techo como se muestra en la Figura 19. Esto le

permite configurar su unidad de calefacción en una

configuración más fría, sin afectar su comodidad.

OPERACIÓN EN VERANO

SENTIDO ANTIHORARIO

OPERACIÓN EN INVIERNO

SENTIDO HORARIO

ESPECIFICACIONES

52"

0.043

0.07

0.11

0.18

0.27

0.42

2.7

4.6

7.6

12.7

20.0

33.0

122

145

173

1635

2566

3396

4221

4918

5779

5.72

kgs

6.66

kgs

1.175’

RENDIMIENTO Y INFORMACIÓN

DE ENERGÍA

Para cualquier información adcional sobre su ventilador

de Techo de Minka Aire por favor escriba a:

VELOCIDAD DE

VENTILADOR

FLUJO DE

AIRE(CFM)*

USO DE POTENCIA

(vatios)

EFICIENCIA DE FLUJO

DE AIRE(CFM/vatio)

Baja

2nd

3rd

Media

5th

Alta

El flujo de ventilador de techo se mide en pies cúbicos por minuto(CFM).

El uso de potencia se mide en vatios. Para maximizar los ahorros de energía:

Seleccione un ventilador con alta eficiencia de flujo(CFM/vatio).

Use -etiquetada iluminando en su ventilador.

Recuerde a apagar su ventilador cuando sala de la habitación

el método de ensayo de

Estado Sólido aprobado

por

Medido de acuerdo con

1635

2566

3396

4221

4918

5779

2.7

4.6

7.6

12.7

20.0

33.0

606

558

447

332

246

175

Minka-Aire F745-DK Instrucciones de operación

Marca: Minka-Aire

Modelo: F745-DK

Categoría: Ventiladores domésticos

Tipo: Instrucciones de operación

Este manual también es adecuado para

Descargar PDF

informe

En otros idiomas

English: Minka-Aire F745-DK Operating instructions

Minka-Aire F745-DK Instrucciones de operación

Este manual también es adecuado para

Minka-Aire F745-DK Instrucciones de operación

En otros idiomas

Documentos relacionados

Otros documentos