Before beginning the installation, thoroughly & completely read these instructions & the enclosed
driver’s WARNING NOTICE. Affix the WARNING decal in the passenger compartment in clear view
of all occupants. Please refer to the Parts List to insure that all parts & hardware are received prior
to the disassembly of the vehicle. If any parts are found to be missing, contact SKYJACKER®
Customer Service at 318-388-0816 to obtain the needed items. If you have any questions or
reservations about installing this product, contact SKYJACKER® Technical Assistance at 318-388-
0816.
Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is not
level (side-to-side) from the factory & is usually not noticed until a lift kit has been installed, which
makes the difference more visible. Using a measuring tape, measure the front & rear (both sides)
from the ground up to the center of the fender opening above the axle. Record this information
below for future reference.
Driver Side Front: Passenger Side Front:
Driver Side Rear: Passenger Side Rear:
Important Notes:
• If larger tires (10% more than the OEM diameter) are installed, speedometer recalibration will be
necessary. Contact your local Jeep dealer or an authorized dealer for details.
• After installation, a qualified alignment facility is required to align the vehicle to the OEM
specifications.
1997- 2006 Jeep TJ Wrangler
2.5" - 3" Suspension Lift
Installation Instructions
REQUIRED TOOL LIST:
• Safety Glasses
• Metric / Standard Wrenches & Sockets
• Drill / Assorted Drill Bits
• Floor Jack
• Jack Stands
• Measuring Tape
• Torque Wrench
I-TJ2530 REV1 9-15 Pg 1
www.skyjacker.com
Component Box Breakdown:
Part #: TJ250 / TJ25BPH / TJ30BPH
Hardware Bag Breakdown:
Part # HB-TJ25
Item # Description Qty Item # Description Qty
10MMX70MMB 10MM X 70MM METRIC BOLT 4 12FTN 1/2 FINE THREAD LOCK NUT 1
12X70MMB 12MM X 70MM METRIC BOLT 1 12SAEW 1/2 SAE WASHER 3
12MMN 12MM METRIC NUT 1 BPS20-B BUMP STOP SPACER 4
12X112FTB 1/2 X 1 1/2 FINE THREAD BOLT 1 SSTJRTB CRUSH SLEEVE 1
Item # Description Qty Item # Description Qty
TJ25FS 2.5" TJ FRONT COIL SPRING 2 H7016 FRONT HYDRO SHK / RED BOOT 2
(Included With TJ25BPH) (Included With TJ25BPH & TJ30BPH)
TJ25RS 2.5" TJ REAR COIL SPRING 2 H7018 REAR HYDRO SHK / RED BOOT 2
(Included With TJ25BPH) (Included With TJ25BPH & TJ30BPH)
TJ30FS 3" TJ FRONT COIL SPRING 2 CAM500 CAM BOLT / UPPER REAR 1
(Included With TJ30BPH) TJRTB-B REAR TRACK BAR BRACKET 1
TJ30RS 3" TJ REAR COIL SPRING 2 HB-TJ25 HDWR BAG: HB-TJ25 1
(Included With TJ30BPH) I-TJ2530 INST SHT: TJ250 / TJ25/30BPH 1
I-TJ2530 Pg 2
Front Installation:
1. Park the vehicle on a level concrete or asphalt surface, set the
emergency brake & block the rear tires / wheels.
2. Raise the front of the vehicle & support securely using jack stands.
3. Remove the front tires / wheels & OEM front shocks.
4. Disconnect the OEM front track bar from the passenger side axle
bracket. (See Photo # 1)
5. Disconnect the OEM drag link assembly from the OEM pitman arm.
6. Disconnect the OEM sway bar end links from the axle brackets. (See
Photo # 2)
7. While supporting the front axle, lower the
front axle until the OEM front coil springs
become loose & remove the OEM
bottom bolt & clip from the left front OEM
coil spring. (See Photo # 3)
Photo # 1
Photo # 2
Photo # 3
I-TJ2530 Pg 3
Photo # 4
8. Remove the OEM front coil springs & OEM upper bump stops. Note:
Use channel lock pliers working the OEM bump stop back & forth to
remove.
9. Remove the OEM 10mm bolt from inside the OEM bump stop cups.
Install the new Skyjacker bump stop spacers & OEM bump stop cups
using the supplied 10mm x 70mm bolts. Reinstall the OEM bump
stops in the OEM bump stop cups. (See Photo # 4)
10. Install the new Skyjacker front coil springs & raise the front axle until
enough load is applied to hold the new front coil springs in place.
Reinstall the OEM spring bolt & clip at the bottom of the left front coil
spring.
11. Install the new Skyjacker front shocks using the supplied hardware &
OEM hardware. (See Photo # 5)
12. Attach the OEM drag link to the OEM pitman arm using the OEM
hardware.
13. Attach the OEM sway bar end links to the the axle brackets using the
OEM hardware.
14. Install the front tires / wheels & lower the front of the vehicle to the
ground.
Rear Installation:
15. Block the front tires / wheels, raise the rear of the vehicle, & support
securely using jack stands.
16. Remove the rear tires / wheels & OEM rear shocks.
17. Disconnect the OEM rear track bar & OEM sway bar end links from
the rear axle.
18. While supporting the rear axle, lower the rear axle until the OEM rear coil springs become loose
& remove the OEM rear coil springs & the OEM upper bump stops. Note: Use channel lock
pliers working the OEM bump stop back & forth to remove.
19. Remove the OEM 10mm bolt from inside the OEM bump stop cups. Install the new bump stop
spacers & OEM bump stop cups using the supplied 10mm x 70mm bolts. Reinstall the OEM
bump stops in the OEM bump stop cups. (See Photo # 6)
Photo # 5
Photo # 6
Pg 4
20. Install the new Skyjacker rear track bar bracket over the OEM rear
track bar bracket & place the OEM rear track bar in the new rear
track bar bracket. Install the supplied 12mm x 70mm bolt through the
OEM lower track bar location using the supplied spacer sleeve,
12mm nut & tighten the bolt to hold the new rear track bar bracket in
place. (See Photo # 7)
21. Drill a 1/2" hole through the hole in the end of the new Skyjacker rear
track bar bracket. Remove the 12mm x 70mm bolt (installed before
drilling) & install the supplied 1/2" x 1 1/2" bolt, with a washer on each
side, through the newly drilled hole & tighten the 1/2" nut. Reinstall
the supplied 12mm x 70mm bolt through the OEM rear track bar
location using the supplied crush sleeve & 12mm nut. Note: Do not
tighten at this time. (See Arrow in Photo # 8)
22. Install the new Skyjacker rear coil springs. Raise the rear axle until
enough load is applied to hold the new rear coil springs in place.
23. Attach the OEM rear track bar to the new Skyjacker rear track bar
bracket using the OEM hardware. Note: Do not tighten at this time.
24. Attach the OEM sway bar end links to the rear axle using the OEM
hardware.
25. Install the new Skyjacker rear shocks using the supplied hardware &
OEM hardware. (See Photo # 9)
26. One side at a time, disconnect the OEM rear upper link from the rear
axle. Note: The OEM hole is notched so it can become a slotted hole.
Knock out the notches on the front & rear half of the OEM hole of the
rear upper link mount. (See Arrows in Photo # 10)
27. Attach the OEM rear upper link to the rear axle using the supplied
cam bolt, eccentric washers, & nut. Note: Do not tighten at this time.
(See Photo # 11) Repeat Step # 26 & # 27 for the opposite side.
28. Install the rear tires / wheels & lower the rear of the vehicle to the
ground.
I-TJ2530
Photo # 7
Photo # 8
Photo # 9
Photo # 10
Photo # 11
29. Tighten the new Skyjacker rear track bar bracket hardware & OEM rear track bar hardware.
30. Tighten the new Skyjacker rear upper link cam bolts. Note: These new cam bolts can be rotated
to adjust the rear axle pinion angle to eliminate any driveline vibration.
Final Notes:
• After the installation is complete, double check that all nuts & bolts are tight. Refer to the following
chart for the proper torque specifications. (Do not retighten nuts & bolts where thread lock
compound was used.)
• With the vehicle placed on the ground, cycle the steering lock to lock & inspect the steering,
suspension, brake lines, front & rear drivelines, fuel lines, & wiring harnesses for proper operation,
tightness, & adequate clearance.
• Have the headlights readjusted to the proper settings.
• Have a qualified alignment center realign the vehicle to the OEM specifications.
• After the first 100 miles, check all hardware for the proper torque & periodically thereafter.
Seat Belts Save Lives, Please Wear Your Seat Belt.
Pg 5I-TJ2530
TORQUE SPECIFICATIONS
INCH SYSTEM
Bolt Size Grade 5 Grade 8
5/16 15 FT LB 20 FT LB
3/8 30 FT LB 35 FT LB
7/16 45 FT LB 60 FT LB
1/2 65 FT LB 90 FT LB
9/16 95 FT LB 130 FTLB
5/8 135 FT LB 175 FT LB
3/4 185 FT LB 280 FT LB
METRIC SYSTEM
Bolt Size Class 8.8 Class 10.9
6MM 5 FT LB 9 FT LB
8MM 18 FT LB 23 FT LB
10MM 32 FT LB 45 FT LB
12 MM 55 FT LB 75 FT LB
14MM 85 FT LB 120 FT LB
16MM 130 FT LB 165 FT LB
18MM 170 FT LB 240 FT LB
• The above specifications are not to be used when the bolt is being installed with a bushing.
Check out our favorite ministries at:
www.innministries.org
www.familychurch.org
www.kcm.org
Jesus Forgives,
Rocks Don’t
Jesus Christ Died For You.
John 3:16
For God so loved the world that He gave His only Son, so that everyone who
believes in Him should not perish, but have everlasting life.
Romans 3:23
For all have sinned; all fall short of God’s glorious standard.
Ephesians 2:8
God saved you by his special favor when you believed. And you can’t take
credit for this; it is a gift from God.
Psalms 18:2
The Lord is my Rock, my fortress, and my savior; my God is my Rock, in
whom I find protection. He is my shield, the strength of my salvation, and
my stronghold.
Romans 10:9-10
That if you shall confess with thy mouth the Lord Jesus, and shall believe in
your heart that God hath raised him from the dead, you shall be saved.
For with the heart man believeth unto righteousness; and with the mouth
confession is made unto salvation.
Pray This Simple Prayer:
God, I come to You admitting I have sinned against You and I need you to
take control of my life. The Bible says anyone who calls on the name of the
Lord will be saved. I am calling on You, Jesus. I ask that You come live in
my heart and be the Lord over my life today. I do believe You died on the
cross for me and came back to life to give me life! Thank You, Lord Jesus
for a new life in You!
Now, go and tell somebody about your new life in Jesus, get a Bible, begin
to read it, and go to a Bible believing church.
If you would like someone to pray with you, call Kenneth Copeland
Ministries anytime at 800-600-7395.
To listen to commercial free Christian radio on the web, go to
www.887fm.org
Juan 3:16
“Porque tanto amó Dios al mundo, que dio a su Hijo unigénito, para que todo
el que cree en él no se pierda, sino que tenga vida eterna.”
Romanos 3:23
“Pues todos han pecado y están privados de la gloria de Dios.”
Efesios 2:8
“Porque por gracia ustedes han sido salvados mediante la fe; esto no procede
de ustedes, sino que es el regalo de Dios.”
Salmos 18:2
“El Señor es mi roca, mi amparo, mi libertador; es mi Dios, el peñasco
en que me refugio. Es mi escudo, el poder que me salva, ¡mi más alto
escondite!”
Romanos 10:9-10
“9 Que si confi esas con tu boca que Jesús es el Señor, y crees en tu corazón
que Dios lo levantó de entre los muertos, serás salvo. 10 Porque con el
corazón se cree para ser justifi cado, pero con la boca se confi esa para ser
salvo.”
Ahora dí esta simple oración:
Dios, vengo a Ti y admito que he pecado contra Ti, necesito que tomes el
control de mi vida. La Biblia dice que todo aquel que invoca el nombre del
Señor escapará con vida. En este momento yo clamo ante Ti, Jesús; te pido
que vengas a vivir en mi corazón y que tomes el control de mi vida. ¡Yo creo
que tu moriste en la cruz y resucitaste para darme vida! ¡Gracias Señor Jesús,
por una nueva vida que tengo en Ti! Amen.
Ahora ve y dile a alguien sobre la nueva vida que tienes en Cristo. Compra
una Biblia y empieza a leerla. Busca una Iglesia que cree en la Biblia y hazte
parte de esa Iglesia.
Si te gustaría orar con alguien, puedes llamar a este número 800-600-7395
Puedes ir a este sitio de Internet para escuchar música Cristiana sin anuncios,
www.887fm.org
Jesús murió por ti.
www.skyjacker.com
-
1
-
2
-
3
-
4
-
5
-
6
