Skyjacker 2-2.5 Dual Rate Long Travel Coil Suspension System Guía de instalación
- Categoría
- Kits de coche
- Tipo
- Guía de instalación
2007-18 Jeep Wrangler JK (2 Door)
2"- 2.5" Suspension Lift
Installation Instructions
www.skyjacker.com
I-JK200BP REV5 1-19 Pg 1
Required Tools List:
• Safety Glasses
• Metric / Standard Wrenches & Sockets
• Assorted Drill Bits
• Floor Jack
• Jack Stands
• Measuring Tape
• Torque Wrench
Before beginning the installation, thoroughly & completely read these instructions & the enclosed
driver’s WARNING NOTICE. Affix the WARNING decal in the passenger compartment in clear view
of all occupants. Please refer to the Parts List to insure that all parts & hardware are received prior
to the disassembly of the vehicle. If any parts are found to be missing, contact SKYJACKER®
Customer Service at 318-388-0816 to obtain the needed items. If you have any questions or
reservations about installing this product, contact SKYJACKER® Technical Assistance at 318-388-
0816.
Make sure you park the vehicle on a level concrete or asphalt surface. Many times a vehicle is not
level (side-to-side) from the factory & is usually not noticed until a lift kit has been installed, which
makes the difference more visible. Using a measuring tape, measure the front & rear (both sides)
from the ground up to the center of the fender opening above the axle. Record this information
below for future reference.
Driver Side Front: Passenger Side Front:
Driver Side Rear: Passenger Side Rear:
Important Notes:
• If larger tires (10% more than the OEM diameter) are installed, speedometer recalibration will be
necessary. Contact your local Jeep dealer or an authorized dealer for details.
• After installation, a qualified alignment facility is required to align the vehicle to the OEM
specifications.
Component Box Breakdown:
Part #: JK20BPBLT / JK20BPMLT / JK200BPBSR / JK200BPHSR / JK200BPMSR /
JK200BPNSR
Item # Description Qty Item # Description Qty
38X234BHB 3/8 X 2 3/4 BUTTON HEAD BOLT 2 716X1FTB 7/16 X 1 FINE TRHEAD BOLT 1
38SAEW 3/8 SAE WASHER 2 716SAEW 7/16 SAE WASHER 1
38CTN 3/8 COARSE N/I LOCK NUT 2 716FTN 7/16 FINE N/I LOCK NUT 1
516X1FTB 5/16 X 1 FINE THREAD BOLT 4 916X3FTB 9/16 X 3 FINE THREAD BOLT 1
516SAEW 5/16 SAE WASHER 8 916SAEW 9/16 SAE WASHER 3
516FTN 5/16 FINE N/I LOCK NUT 4 916FTN 9/16 FINE N/I LOCK NUT 2
12X114FTB 1/2 X 1 1/4 FINE THREAD BOLT 1 CS1625 CRUSH SLEEVE JKRTB 1
12SAEW 1/2 SAE WASHER 1 BSS3020-S BUMP STOP SPACER BLK, 2" 2
12FTN 1/2 FINE N/I LOCK NUT 1 916X312FTB 9/16 X 3 1/2 FINE THREAD BOLT 1
Front Installation:
1. With the vehicle on flat level ground, set the emergency brake, & block the rear tires / wheels.
2. Raise the front of the vehicle & support the frame rails using jack stands.
3. Remove the front tires / wheels.
4. Disconnect the OEM front sway bar end links using a 18mm socket.
5. Disconnect the OEM front track bar from the axle using a 21mm socket.
(See Photo # 1)
6. If installing a new Skyjacker Steering
Stabilizer (Part # 7003), remove the OEM
steering stabilizer using a 18mm socket.
(See Photo # 2)
7. Remove the OEM front shocks using a
18mm socket.
8. Lower the differential & remove the OEM
front coil springs. (See Photo # 3)
Hardware Bag Breakdown:
Part # HB-JK2500
Item # Description Qty Item # Description Qty
JK20FS-SR/JL10FS-DR JK FRT COIL SPRING 2 B8535/H7035/M9535/N8035 FRONT SHOCK 2
JK20RS-DR/JK20RS-SR JK REAR COIL SPRING 2 B8565/M9565 (Long Travel Kits) FRONT SHOCK 2
JK24RTB-B JK REAR TRK BAR BRK 1 B8537/H7037/M9537/N8037 REAR SHOCK 2
JK25RBS-S JK REAR BMP STP BRK 2 B8567/M9567 (Long Travel Kits) REAR SHOCK 2
HB-JK2500 HWR BG: JK 2-2.5" 1 I-JK200BP INST SHT: 2-2.5" JK 1
Pg 2I-JK200BP
Photo # 2
Photo # 1
Photo # 3
9. Place the new Skyjacker bump stop spacers on the center of the OEM
bump stop pad located on the front axle. Mark & drill using a 25/64" drill
bit. (See Photo # 4)
10. Install the new bump stop spacers & new Skyjacker front coil springs.
Attach the new bump stop spacers to the axle using the supplied 3/8" x
2 3/4" button head bolts, washers, & nuts. (See Photo # 5)
11. Raise the differential in order to load the new front coil springs & attach
the OEM front track bar to the axle using the OEM hardware.
12. Attach the OEM front sway bar end links using the OEM hardware.
13. If installing a new Skyjacker steering stabilizer (Part # 7003), install it at
this time. (See Photo # 6)
14. Install the new Skyjacker front shocks using the supplied hardware. (See
Photo # 7)
15. Install the front tires / wheels & lower the vehicle to the ground.
Rear Installation:
16. Block the front tires / wheels,
raise the rear of the vehicle, &
properly support the frame
rails using jack stands.
17. Remove the rear tires / wheels.
18. Remove the OEM rear shocks using a 16mm socket. (See Photo # 8)
19. Disconnect the OEM rear track bar from the axle using a 21mm socket. (See Photo # 9)
Photo # 4
Pg 3I-JK200BP
Photo # 5
Photo # 6
Photo # 7 Photo # 8 Photo # 9
Pg 4I-JK200BP
20. Disconnect the OEM rear sway bar end links using a 18mm socket.
21. Disconnect the OEM ABS line & brake line from the frame. (See
Photo # 10)
22. Lower the differential & remove the OEM rear coil springs.
23. Place the new Skyjacker rear track bar bracket over the OEM track
bar bracket on the axle. With the new track bar bracket seated flush,
clamp the new track bar bracket in place, mark with a center punch,
& drill the new center mounting holes using a 15/32" drill bit. (See
Photo # 11)
24. Install the new track bar bracket using the supplied 7/16" x 1" fine
thread bolt, washer, & nut. (See Photo # 12)
25. It will be necessary to drill through the driver side bottom of the OEM
track bar bracket & through the new track bar bracket. Drill using a
17/32" drill bit. Once drilled, install the supplied 1/2" x 1 1/4" fine
thread bolt, washer, & nut. Install the supplied 9/16" x 3 1/2" bolt,
washers, & nut at the bottom location being sure to use the supplied
crush sleeve. (See Arrow in Photo # 13)
26. Install the new Skyjacker rear coil springs. Note: Be sure to re-use
the OEM upper rubber isolator pads.
27. Attach the new Skyajcker rear bump stop spacers to the OEM
location on the axle using the supplied 5/16" x 1" fine thread bolts,
washers, & nuts. (See Photo # 14) Note: Be sure to install the new
bump stop spacers so the angled end is towards the rear of the
vehicle.
28. Raise the differential in order to load the new rear coil springs & attach
the OEM rear track bar to the lower mounting hole of the new rear track
bar bracket using the supllied 9/16" x 3" fine thread bolt, washer, & nut.
29. Attach the OEM rear sway bar end links using the OEM hardware.
30. Attach the OEM ABS line & brake line to
the frame using the OEM hardware.
Photo # 10
Photo # 12
Photo # 11
Photo # 13
Photo # 14
Pg 5I-JK200BP
31. Install the new Skyjacker rear shocks using the supplied hardware.
(See Photo # 15)
32. Install the rear tires / wheels & lower the vehicle to the ground.
Final Notes:
• After the installation is complete, double check that all nuts & bolts are
tight. Refer to the following chart for the proper torque specifications.
(Do not retighten the nuts & bolts where thread lock compound was
used.)
• With the vehicle placed on the ground, cycle the steering lock to lock & inspect the steering,
suspension, brake lines, front & rear drivelines, fuel lines, & wiring harnesses for proper operation,
tightness, & adequate clearance.
• Have the headlights readjusted to the proper settings.
• Have a qualified alignment center align the vehicle to the OEM specifications.
• After the first 100 miles, check all hardware for the proper torque & periodically thereafter.
Seat Belts Save Lives, Please Wear Your Seat Belt.
Photo # 15
TORQUE SPECIFICATIONS
INCH SYSTEM
Bolt Size Grade 5 Grade 8
5/16 15 FT LB 20 FT LB
3/8 30 FT LB 35 FT LB
7/16 45 FT LB 60 FT LB
1/2 65 FT LB 90 FT LB
9/16 95 FT LB 130 FTLB
5/8 135 FT LB 175 FT LB
3/4 185 FT LB 280 FT LB
METRIC SYSTEM
Bolt Size Class 8.8 Class 10.9
6MM 5 FT LB 9 FT LB
8MM 18 FT LB 23 FT LB
10MM 32 FT LB 45 FT LB
12 MM 55 FT LB 75 FT LB
14MM 85 FT LB 120 FT LB
16MM 130 FT LB 165 FT LB
18MM 170 FT LB 240 FT LB
• The above specifications are not to be used when the bolt is being installed with a bushing.
Check out our favorite ministries at:
www.innministries.org
www.familychurch.org
www.kcm.org
Jesus Forgives,
Rocks Don’t
Jesus Christ Died For You.
John 3:16
For God so loved the world that He gave His only Son, so that everyone who
believes in Him should not perish, but have everlasting life.
Romans 3:23
For all have sinned; all fall short of God’s glorious standard.
Ephesians 2:8
God saved you by his special favor when you believed. And you can’t take
credit for this; it is a gift from God.
Psalms 18:2
The Lord is my Rock, my fortress, and my savior; my God is my Rock, in
whom I find protection. He is my shield, the strength of my salvation, and
my stronghold.
Romans 10:9-10
That if you shall confess with thy mouth the Lord Jesus, and shall believe in
your heart that God hath raised him from the dead, you shall be saved.
For with the heart man believeth unto righteousness; and with the mouth
confession is made unto salvation.
Pray This Simple Prayer:
God, I come to You admitting I have sinned against You and I need you to
take control of my life. The Bible says anyone who calls on the name of the
Lord will be saved. I am calling on You, Jesus. I ask that You come live in
my heart and be the Lord over my life today. I do believe You died on the
cross for me and came back to life to give me life! Thank You, Lord Jesus
for a new life in You!
Now, go and tell somebody about your new life in Jesus, get a Bible, begin
to read it, and go to a Bible believing church.
If you would like someone to pray with you, call Kenneth Copeland
Ministries anytime at 800-600-7395.
To listen to commercial free Christian radio on the web, go to
www.887fm.org
Juan 3:16
“Porque tanto amó Dios al mundo, que dio a su Hijo unigénito, para que todo
el que cree en él no se pierda, sino que tenga vida eterna.”
Romanos 3:23
“Pues todos han pecado y están privados de la gloria de Dios.”
Efesios 2:8
“Porque por gracia ustedes han sido salvados mediante la fe; esto no procede
de ustedes, sino que es el regalo de Dios.”
Salmos 18:2
“El Señor es mi roca, mi amparo, mi libertador; es mi Dios, el peñasco
en que me refugio. Es mi escudo, el poder que me salva, ¡mi más alto
escondite!”
Romanos 10:9-10
“9 Que si confi esas con tu boca que Jesús es el Señor, y crees en tu corazón
que Dios lo levantó de entre los muertos, serás salvo. 10 Porque con el
corazón se cree para ser justifi cado, pero con la boca se confi esa para ser
salvo.”
Ahora dí esta simple oración:
Dios, vengo a Ti y admito que he pecado contra Ti, necesito que tomes el
control de mi vida. La Biblia dice que todo aquel que invoca el nombre del
Señor escapará con vida. En este momento yo clamo ante Ti, Jesús; te pido
que vengas a vivir en mi corazón y que tomes el control de mi vida. ¡Yo creo
que tu moriste en la cruz y resucitaste para darme vida! ¡Gracias Señor Jesús,
por una nueva vida que tengo en Ti! Amen.
Ahora ve y dile a alguien sobre la nueva vida que tienes en Cristo. Compra
una Biblia y empieza a leerla. Busca una Iglesia que cree en la Biblia y hazte
parte de esa Iglesia.
Si te gustaría orar con alguien, puedes llamar a este número 800-600-7395
Puedes ir a este sitio de Internet para escuchar música Cristiana sin anuncios,
www.887fm.org
Jesús murió por ti.
www.skyjacker.com
-
1
-
2
-
3
-
4
-
5
-
6
Skyjacker 2-2.5 Dual Rate Long Travel Coil Suspension System Guía de instalación
- Categoría
- Kits de coche
- Tipo
- Guía de instalación