Transcripción de documentos

6 2.2m-2.5m (7'-8') 1 3 2 PIR & PIR Pet Detectors PIR 868/433MHz Model:RWX95 PIR Pet 868/433MHz Model: RWX95P CR 123, 3V Lithium PIR: 12 A standby Pet: 16 A standby 868.65MHz / 433.92MHz T 0-255 min. -10°C > 40°C (14°F > 104°F) = 3 Y Typical 67.5mm (2.6") 132mm (5.1") 56mm (2.2") -10°C > 40°C (14°F > 104°F) x2 x3 x2 < 36kg (80lb) 3A 4 5 T EN Registering the Detector into the system The iWave must identify itself to the system receiver. This can be done by typing the 11 digit serial number of the detector into the system or using RF mode. To register the detectors using the serial number refer to the system installation manual. Enrolling using RF communication 1.Set the receiver to Learn mode. 2.Insert the batteries and press the tamper switch for at least 3 seconds. The iWAVE will send a WRITE message. A successful learning will be indicated by: (A) The system will sound a confirmation message and indicate the detector allocation in the system. (B) The iWAVE will blink. IT Registrare il rilevatore nel sistema iWave deve essere identificato dal ricevitore del sistema. Per farlo, inserire il numero di serie a 11 cifre del rilevatore nel sistema o utilizzare la modalità RF. Per registrare il rilevatore utilizzando il numero di serie, fare riferimento al manuale di installazione. Acquisizione tramite comunicazione RF 1. Impostare il ricevitore in modalità di apprendimento. 2. Inserire le batterie e premere l’interruttore tamper per almeno 3 secondi. iWAVE invierà un messaggio WRITE se l’apprendimento è riuscito: (A) Il sistema emetterà un segnale acustico con messaggio di conferma indicando l’allocazione del rilevatore nel sistema. (B) iWAVE lampeggia. SP Registro del detector en el sistema El iWave debe identificarse en el receptor del sistema. Esto puede hacerse escribiendo en el sistema el número de serie de 11 dígitos del detector, o bien usando el modo RF (Radio Frecuencia). Para registrar el detector usando el número de serie, consulte el manual de instalación. Alta del detector usando la comunicación RF 1. Ponga al receptor en modo Aprendizaje. 2. Inserte las pilas y pulse el interruptor del tamper durante al menos 3 segundos. El iWAVE enviará un mensaje de Escritura. Si se ha dado de alta correctamente: (A) El sistema emitirá un mensaje de confirmación e indicará la asignación de detector en el sistema. (B) El iWAVE parpadeará. FR Enregistrement du détecteur dans le système Le modèle iWave doit être identifié par le système récepteur. Ceci peut être fait en entrant les 11 chiffres du numéro de série du détecteur dans le système ou en employant le mode RF. Pour enregistrer le détecteur en utilisant le numéro de série, consultez le manuel d'installation. Utilisation de la communication RF pour l'inscription 1.Réglez le récepteur en mode d'apprentissage. 2.Insérez les batteries et appuyez sur le commutateur du dispositif anti-sabotage durant au moins 3 secondes. Le iWAVE enverra un message ECRIT. Le succès de l'apprentissage sera indiqué par : (A) Le système fera retentir un message de confirmation et indiquera l'inscription du détecteur dans le système. (B) Le iWAVE clignotera. PR Registrando o detector no sistema O iWave deve identificar-se ao receptor do sistema. Isto pode ser executado ao digitar o número de série de 11 dígitos do detector no sistema ou utilizando o modo de rádio freqüência. Para registrar o detector utilizando o número de série, consulte o manual de instalação do sistema. Inscrição através de comunicação de rádio freqüência 1.Configure o receptor para o modo "Learn". 2.Introduza as pilhas e pressione o interruptor do tamper por pelo menos 3 segundos. O iWAVE enviará uma mensagem WRITE. Um aprendizado bem sucedido será indicado por : (A) O sistema enviará o som de uma mensagem de confirmação, e indicará a atribuição do detector no sistema. (B) O iWAVE irá piscar. De detector in het systeem registreren NL De iWave moet zichzelf bij de systeemontvanger identificeren. Dit kan worden gedaan door het digitale serienummer 11 van de detector in het systeem of met RF-modus te typen. Om de detectors met het serienummer te registreren, moet u de installatiehandleiding van het systeem raadplegen. Met RF-communicatie registreren: 1.Stel de ontvanger in op de modus Leren 2.Plaats de accu’s en druk op gedurende minstens 3 seconden op de sabotageschakelaar. De iWAVE verzendt een bericht SCHRIJVEN. Een succesvol leerproces wordt door het volgende aangegeven: (A) Het systeem laat een bevestigingsbericht horen en geeft in het systeem de detectortoewijzing aan. (B) De iWAVE knippert. 8 7 9 EN Parameters set by the system: Parameters Sensitivity Operation Supervision LED 0-20Min 5 IT Parametri impostati dalla centrale: Parametri Sensibilita’ Modo operativo Supervisione LED Option Low/High Normal (2.5 min) / Walk Test (0) 0-255 min Off/On For more information refer to the Installer Guide. Normal 2.5 min. A B 10 ft m PIR - TOP VIEW 30 9 20 7 20 6 15 5 15 4 10 10 3 5 2 5 1 0 0 0 5 1 5 10 2 10 3 15 4 15 20 5 20 6 25 7 25 ft 25 8 25 8 30 30 9 0 1 0 2 5 3 10 ft. m 10 3 5 4 15 5 6 20 7 25 8 9 10 11 12 13 14 15 m 35 40 45 50 ft 30 PIR - SIDE VIEW 0 1 EN IT SP FR PR NL 0 0 1 2 5 3 10 4 5 6 15 20 7 8 9 10 11 12 13 14 15 m 25 30 35 40 45 50 ft 7 6 EN50131-1, 5 4 RTC 50131-2-2, EN50131-2-2 Grade 2 Class II 3 EN50130-5 Environmental Class II 2 1 Indice de Protection (IP): IP31 0 1 EN50131-6: Type C 2 Batterie Basse 2.6V 3 5 6 7 8 90 0 1 2 5 3 10 4 15 5 6 20 7 8 25 9 10 11 12 30 35 40 PIR Pet - SIDE VIEW 2 EN50131–5-3 Grade 2 Organisme de certification AFNOR CERTIFICATION: 11 rue Francis de Pressensé 93571 LA PLAINE SAINT-DENIS Cedex, http://www.marque-nf.com CNPP Cert: BP 2265, 27950 ST MARCEL, http://www.cnpp.com Certificate number for RWX95: 2622000015A0 Certificate number for RWX95P: 2622000015B0 1 0 0 IK 04 Consommation électrique: 34 mA max. 4 1 2 5 3 4 5 10 15 6 7 8 20 25 9 10 11 12 m 30 35 40 ft These detection pattern is only assured and approved according to EN50131 in High sensitivity settings. For low sensitivity setting, the actual detection pattern must be assured during the installation. Questo metodo di rilevazione è assicurato e approvato in accordo con la norma EN50131 solo quando il rilevatore è in ALTA SENSIBILITA’. Per il settaggio in bassa sensibilità, questo metodo di rilevazione è assicurato solamente durante l’installazione. Estos patrones de detección sólo están garantizados y aprobados conforme a EN50131 en la configuración de Alta sensibilidad. Para la configuración de Baja sensibilidad, el patrón exacto de detección debe asegurarse durante la instalación. Cette couverture de détection n’est assurée et approuvée selon la norme EN50131 qu’avec un réglage en Haute Sensibilité. Pour un réglage avec une Faible Sensibilité, la couverture de détection devra être vérifiée au cours de l’installation. Este padrão de detecção só é garantido e aprovado de acordo com a EN50131 com o ajuste para alta sensibilidade. Para ajuste de baixa sensibilidade, o padrão real de detecção deve ser certificado durante a instalação. Deze detectie patroon, in lijn met de EN 50131 norm, zijn alleen geldig als de parameters op het maximum gevoeligheid niveau afgesteld zijn. Voor een lager detectie niveau, de detectie patroon zou op het moment van de installatie moeten afgesteld worden. FR Paramètres configurés: Opción Baja / Alta Normal (2,5 min)/Test de Paseo (0) 0-255 min Apagado / Encendido Paramètres Sensibilité Operation Surveillance LED Déclaration de Conformité RTTE Par la présente, RISCO Group déclare que cet accessoire est en conformité avec les conditions essentielles et à d’autres dispositions appropriées de la directive 1999/5/EC. Pour obtenir la copie complète de conformité, référez-vous à notre site web : www.riscogroup.com Option Faible/Elevé Normal (2.5 min)/Test de marche (0) 0-255 min Off/On Para más información, consulte el manual de instalación. Pour plus d'informations, consultez le manuel d'installation. PR Parâmetros do seteo: NL Geprogrammeerde parameters: Parâmetros Sensibilidade *Operação Supervisão LED Geprogrammeerde Gevoeligheid * Bedrijfsmodus Controletijd LED Opção Baixa/Alta Normal (2.5 min)/Teste de Caminhada (0) 0-255 min Desativado/Ativado Para mais informações, consulte o guia de instalação do sistema. [France only]: Déclaration de conformité Par la présente, RISCO Group déclare que la série Agility des centrales et accessoires a été conçue conformément aux normes: PIR Pet - TOP VIEW m 8 ft m 10 3 5 2 0 C 10A Per maggiori informazioni vedere la guida di installazione. SP Parámetros configurados: Parámetros Sensibilidad Funcionamiento Supervisión LED Opzione Bassa/Alta Normale (2.5 min)/Test Sensore (0) 0-255 min Off/On FCC part 15 statement and warnings (Models: RWX95 and RWX95P) Optie Hoog/laag Normaal (2.5 min)/Looptest (0) 0-255 min Uit/Aan Raadpleeg de systeeminstallatiehandleiding voor meer informatie. RISCO Group Limited Warranty NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC ID: JE4AGILITY IC: 6564A-AGILITY APPROVALS (Models: RWX95 and RWX95P) EN50131-1, EN50131-2-2 Grade 2 Class II EN50130-5 Environmental Class II EN50131-6: Type C EN50131–5-3 Grade 2 RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller cannot guarantee the performance of the security system which uses this product. Seller's obligation and liability under this warranty is expressly limited to repairing and replacing, at Seller's option, within a reasonable time after the date of delivery, any product not meeting the specifications. Seller makes no other warranty, expressed or implied, and makes no warranty of merchantability or of fitness for any particular purpose. In no case shall seller be liable for any consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever. Seller's obligation under this warranty shall not include any transportation charges or costs of installation or any liability for direct, indirect, or consequential damages or delay. Seller does not represent that its product may not be compromised or circumvented; that the product will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of burglary, robbery or fire without warning, but is not insurance or a guaranty that such event will not occur or that there will be no personal injury or property loss as a result thereof. Consequently seller shall have no liability for any personal injury, property damage or loss based on a claim that the product fails to give warning. However, if seller is held liable, whether directly or indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of cause or origin, seller's maximum liability shall not exceed the purchase price of the product, which shall be complete and exclusive remedy against seller. No employee or representative of Seller is authorized to change this warranty in any way or grant any other warranty. WARNING: This product should be tested at least once a week. Ce produit répond aux exigences du référentiel de certification NF324-H58 pour la classification 2 boucliers, et de la RTC 50131-2-2 Contacting RISCO Group RISCO Group is committed to customer service and product support. You can contact us through our website www.riscogroup.com or as follows: United Kingdom Tel: +44-161-655-5500 [email protected] Spain Tel: +34-91-490-2133 [email protected] Belgium Tel: +32-2522 7622 [email protected] Brazil Tel: +1-866-969-5111 [email protected] Poland Tel: +48-22-500-28-40 [email protected] Italy Tel: +39-02-66590054 [email protected] France Tel: +33-164-73-28-50 [email protected] USA Tel: +1-631-719-4400 [email protected] China Tel: +86-21-52-39-0066 [email protected] Israel Tel: +972-3963-7777 [email protected] © RISCO Group 04/2014 5IN1089 E