Panasonic TC-22LH1 El manual del propietario

Marca: Panasonic

Modelo: TC-22LH1

Tipo: El manual del propietario

PanasoniC °

} _ _ !_ L !i_! _ :_; _ _: __

:_ ! • _ _!!_il ;i!!i_ !i!! i¸I

LCD TV

Operating Instructions

Model No. TC-22LH1

For assistance, please call : 1-800-211-PANA (7262)

or send e-mail to : [email protected]

or visit us at www.panasonic.com (U.S.A)

For assistance, please call : 787-750-4300

or visit us at www.panasonic.com (Puerto Rico

For assistance, please call : 1-800-561-5505

or visit us at www.panasonic.ca (Canada)

Before connecting, operating or adjusting this product, please read these instructions completely.

Please keep this manual for future reference.

English

TQBC0633-1

Important Safety Instructions

CAUTION

,_ The lightning flash with arrow ,_

head within atriangle isintended

to tell the user that parts inside

the product are a risk of electric

shock to persons.

The exclamation point within a

triangle is intended to tell the

user that important operating

and servicing instructions ere in

the papers with the appliance.

• Note to CATV System Installer: This reminder is provided to direct the CATV system installer's

attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the grounding system of the building,as close to the

point of cable entry as practical.

• Important Safety Instructions for LCD TV

1) Read these instructions.

All the safety and operating instructions should be read before the appliance is operated.

2) Keep these instructions.

The safety and operating instructions should be retained for future reference.

3) Heed all warnings.

All wamings on the appliance and in the operating instructionsshould be adhered to.

4) Follow all instructions.

All operating and use instructions should be followed.

5) Do not use this apparatus near water.

For exampte, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a

swimming pool, and the like.

6) Clean only with dry cloth.

Do not use liquidcleaners or aerosol cleaners. Use a dry cloth for cleaning.

7) Do not block any ventilationopenings. Install in accordance withthe manufacturer's instructions.

Slots and Openings in the cabinet are provided for ventilation and to ensure reliable operation ofthe

product and to protect it from overheating. The openings should never be blocked by placing the

product on a bed, sofa, rug, or other similar surface.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

This product should not be placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided or the manufacturer's instructionshave been adhered to.

9) Protect the power cord from being walked on or pinched particularlyat plugs, convenience receptacles,

and the point where they exit from the apparatus.

10) Only use attachments / accessories specified by the Manufacturer.

11) Use only with the cart, stand, tripod, bracket, or table specified bythe manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid

injuryfrom tip-over.

Quick stops, excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn. _1_'_

12) Unplug this apparatus during lightning storms or when unused for long periods of time.

This will prevent damage to the product due to lightning and power-line surges.

13) Refer allservicing to qualified service personnel. Servicing is requiredwhen the apparatus hasbeen damaged in

any way,such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain ormoisture, does notoperate normally, or has been dropped.

14) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.

Important Safety Instructions

15) If an outside antenna is connected to the

television equipment, be sure theantenna system

is grounded so as to provide some protection

against voltage surges and built up static

charges. In the U.S. Selection 810-21 of the

National Electrical Code provides information

with respect to proper grounding of the mast and

supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit,

connection to grounding electrodes, and

requirements for the grounding electrode.

16) An outside antenna system should not be located

in the vicinity of overhead power lines or other

EXAMPLE OFANTENNA

GROUNDING AS PER (NEC)

NATIONAL ELECTRICAL _._

CODE

L EQUIPMENT_ _ J_

ANTENNA

LEAD-IN WIRE

_ ANTENNA

•,-- DISCHARGE UNIT

(NECSECTION810-20)

_'J GROUNDINGCONDUCTORS

(NECSECTION810-21)

GROUND CLAMPS

_-- POWERSERVlCEGROUNDING

ELECTRODESYSTEM

(NECART250, PARTH)

electric light or power circuits, or where it can fall into such power lines or circuits. When installing an

outside antenna system extreme care should be taken to keep from touching such power lines or circuits

as contact with them might be fatal.

17) Unplug this LCD TV from the wall outlet, and refer servicing to qualified service personnel under the

following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the LCD TV.

c. If the LCD TV has been exposed to rain or water.

d. If the LCD TV does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions as improper adjustment of other

controls may result in damage and will often require extensive work by a qualified technician to restore

the LCD TV to normal operation.

e. If the LCD TV has been dropped or the cabinet has been damaged.

f. When the LCD TV exhibits a distinct change in performance - this indicates a need for service.

18) When replacement parts are required, be sure the service technician uses replacement parts specified by

the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may

result in fire, electric shock, or other hazards.

19) WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPARATUS TO RAIN OR MOISTURE.

DO NOT PLACE LIQUID CONTAINERS (FLOWER VASES, CUPS, COSMETICS, ETC.) ABOVE THE

SET. (INCLUDING ON SHELVES ABOVE, ETC.)

20) CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS PLUG WITH A RECEPTACLE OR

OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE: • This equipment is designed to operate in the U.S.A. and other countries where the broadcasting

system and AC house current is exactly the same as in the U.S.A.

• The marking or retained image on the LCD panel resulting from fixed image use is not an operating

defect and as such is not covered by Warranty. This product is not designed to display fixed image

patterns for extended periods of time.

• Important Information Regarding Use of Video Games, Computers, Captions or Other Fixed Image Displays.

The extended useof fixed image programmaterial can cause a permanent "shadowimage"on the LCD panel.

This background image is viewable on normal programs in the form of a stationary fixed image. This type of

irreversibleLCD panel deteriorationcan be limitedby observingthe followingsteps:

A. Reduce the bdghtness/contrast setting to a minimum viewing level.

B, Do not display the fixed image for extended periods of time.

C. Turn the power off when not in actual use.

• Thisproduct utilizestin-lead solder,and hasa fluorescent lampcontaining a small amountof memury. Disposal

ofthese materials may be regulated in your community due to environmental considerations. Fordisposal or

recyclinginformationplease contact your localauthorities,or the ElectronicsIndustriesAlliance:www.eiae.orq.

Dear Panasonic Customer

Welcome to the Panasonic family of customers.

We hope that you will have many years of enjoyment from yotlr izew LCD TV.

To obtain maximum benefit from your set, please read these instructions before

making any adjustments, and retain them for future reference.

Retain your purchase receipt, and record the model number and serial number

of your set in the space provided on the rear cover of these instructions.

For assistance, please call : 1-800-211-PANA (7262)

or send e-mail to : [email protected]

or visit us at www.panasonic.com (U.S.A)

For assistance, please call • 787-750-4300

or visit us at www.panasonic.com (Puerto Rico)

For assistance, please call : 1-800-561-5505

or visit us at www.panasonic.ca (Canada)

I Federal Communication Commission Information I

This equipment has been tested and found to comply with the limits for a TV Broadcast Receiver, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause or receive interference, which can be determined by turning

equipment off and on, the user is encouraged to try to correct the interference by one er more of the

following measures:

Reorient or relocate the TV antenna.

Increase the separation between TV and other equipment.

Connect TV into separate outlet from other equipment.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Pursuant to 47CFR, Part 15.21 of the FCC rules, any changes or modifications not expressly

approved by the party responsible for compliance could void the user's authority to operate this equipment.

_ HDMI, the HDMI logo and High-Definition Multimedia Interface

are trademarks or registered trademarks of HDMI Licensing LLC.

HIGH-DEFINITION MULTIMEDIA INTERFACE

Table of Contents

Important Safety Instructions .............................. 2

Installation ............................................................. 6

SUPPLIED ACCESSORIES ................................ 6

Remote control battery installation ...................... 7

Maintenance .......................................................... 7

Connections .......................................................... 8

ConnectingtheAntennaCableto theAntennaTerminal.... 8

Antenna cover removal and fitting ....................... 8

Antenna / Cable Connection ................................ 8

Cable cover removal and fitting ......................... 10

How to connect the input terminals ................... 10

How to connect the HDMI Terminal ................... 12

Power ON/OFF ................................................... 13

Connecting the Plug to the Wall Outlet .............. 13

How to Turn the Power On ................................ 13

Location of Controls ........................................... 14

Illuminated Remote Control ............................... 14

Flow Chart of MENU ............................................ 16

Tuning channels

(Automatic channel programming) ............. 18

Tuning channels

(Manual channel programming) ................... 19

ASPECT Controls ................................................ 20

Picture Adjustments ........................................... 21

Position / Size Adjustment ................................. 23

Audio Adjustments ............................................. 24

Lock Feature ........................................................ 25

Closed Captions .................................................. 29

Customizing the VIDEO INPUT labels ............... 30

OTHER ADJUST .................................................. 30

Operating peripheral equipment

using the remote control ........................... 31

Programming The Illuminated

Remote Control Using Access Codes .......... 31

Programming Without A Code

(When the code is not known) ...................... 32

infrared Codes Index ......................................... 33

IMode Operational Key Chart ............................ 35

--Manual de instrucciones [ Resumen ] --

Preparacion .................................................. 36

Instalaci6n de las pilas en el control remoto .... 36

Conexibn ....................................................... 37

C0nexiondelcabledeantenaalterminaldeentradadeRF. 37

Desmontajeeinstalaci6ndelacubiefladela antena.........37

Conexi6n de antena / cable ........................... 37

Para quitar y colocar la cubierta del cable ..... 38

Como conectar el termino del entrada/salida .... 38

Conexi6n/desconexibn de la alimentaci6n ... 39

Conexi6n de la clavija a latoma de corriente ... 39

C6mo conectar la alimentaci6n ...................... 39

Ubicacion de los controles ......................... 40

Control remoto iluminado ............................... 40

Organigrama de ment_s de televisibn ........ 42

Sintonizacibn de canales

(Programaci6nautomdtica de canales) ..... 44

Sintonizacion de canales

(Programaci6n manual de canales) ...... 45

Troubleshooting .................................................. 46

Specifications ...................................................... 47

I Installation

Receiver Location

Locateforcomfortableviewing.Avoidplacingwheresunlightor otherbrightlight(includingreflections)willfallon thescreen.

Use ofsome typesof fluorescentlightingcan reduceremotecontroltransmitterrange.

Adequateventilationis essentialtopreventinternalcomponentfailure.Keepawayfrom areasofexcessiveheator moisture.

Optional External Equipment

The Video/Audio connection between components can be made with shielded video and audio cables. For

best performance, antenna cables should utilize 75 ohm coaxial shielded wire. Cables are available from

your dealer or electronic supply store.

Before you purchase any cables, be sure you know what type of output and input connectors your various

components require. Also determine the length of cable you'll need.

For optimum quality picture

When the LCD is exposed to light from outdoors or lighting fixtures, high-contrast pictures may not bedisplayed

clearly. Turn off florescent lamps near the LCD and place in a location not exposed to outdoor light.

Row to use the LCD stand

Adjust the stand to your desired angle. The stand angle can be adjusted between 5 ° front to 15 ° back.

SUPPLIED ACCESSORIES

Check the accessories before installations.

• Operating Instruction book • Remote Control Transmitter

tllatl=le_

• Batteries for the Remote

Control Transmitter

• Warranty Card

• AC Adaptor & AC Cord • Coaxial Antenna Plug

Installation

Remote control battery installation

Replacing batteries

Replace batteries by following the steps below:

Requires two AA batteries.

1. Open the battery cover.

2. Install the batteries as shown

in the battery compartment.

(Polarity + or- must match the

markings in the compartment).

JJ2 -.Two AA size

3. Replace the cover.

/_ Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control

transmitter.

Observe the following precautions:

1. Always use new batteries when replacing the old set.

2. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

3. Battery replacement is necessary when remote control acts sporadically or stops operating this unit.

Notes:

• Do not drop, apply shock to or step on the remote control.

• Do not spill water on the remote control.

• Do not place objects between the remote control and remote control receiver.

• Do not use remote controls for other equipment at the same time.

• If the TV does not operate even when operating the remote control from a close range, it is time to

replace the batteries.

Refer to the label on back of the remote control for directions on replacing batteries.

I Maintenance

To clean this unit, wipe with a soft, dry cloth.

If the surfaces are extremely dirty, use a soft cloth dipped in a soap and

water solution or a weak detergent solution.

• Use eyeglass cleaner to remove stubborn dirt from the LCD.

• Never use alcohol, paint thinner or benzine to clean this unit.

• Before using a chemically treated cloth, read the instructions that came

with the cloth carefully.

CAUTION :

If water or similar substances get inside the monitor via the liquid crystal panel surface, a malfunction may result.

I Connections

Connecting the Antenna Cable to the Antenna Terminal

Antenna Connection - For proper reception of VHF/UHF channels, an external antenna is required. For best

reception an outdoor antenna is recommended. Antenna Mode must be set to TV.

VHF Antenna

UHF Antenna

Ca4

Antenna Terminal

(ANT or VHF/UHF)

Coaxial Antenna Plug

Antenna cover removal and fitting

•Hook

(_ Removal

1.Push up hooks and pull the cover slightly towards yourself to

disengage the claws (at 4 points)•

2.Slowly pull out in the downward direction•

(_ Fitting

1,Insert the claws (at 4 points) at the bottom end.

2.Push ituntil hook is locked.

Note:

To avoid interference appearing on the screen, do not bundle the antenna wire and AC adapter wire together.

Antenna / Cable Connection

Incoming 75 Ohm Cable from Home Antenna / Cable Company

F-TypeAntennaAdapter (supplied)

ANT (VHF/UHF) __

onthe BackoftheTV

Cable Connection- Forreceptionof cablechannels (01 * 125) connectthe cablesuppliedby yourlocalcable company•

Antenna Mode must be set to CABLE•(Refer to Antenna Mode section.)

Note:

Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable

converter box is required for proper reception. Check with your local Cablecompany for its compatibility requirements.

Connections

I Antenna Connection (Cable Box, no VCR) 1

Use this configuration when connecting the TV to a cable TV system using a Cable Box.

ANTENNA TERMINAL

(ANT or VHF/UHF)

ON THE BACK OF

THE TV

CABLE BOX

[,, ,J

-I

[

.......... I

i Connect the cable from the Output

terminal on the back of the Cable

Box to the ANTENNA terminal on

the back of the TV.

TERMINALS ON THE BACK OF

THE CABLE BOX

Incoming Cable from

Antenna or Cable TV

System

I Antenna (Cable Box, VCR)

Connection and

Use this configuration when connecting the "IV to a cable TV system using a Cable Box and VCR,

CABLE BOX

ANTENNATERMINAL

(ANT or VHF/UHF)

ON THE BACK OF

THE TV

Connect the cable from the

Output terminal on the back

of the Cable Box to the

Antenna Input terminal on

the back of the VCR.

Connect the

cable from the

Antenna Output

terminal on the

back of the VCR

to the Antenna

terminal (ANT or

VHF/UHF) on the

back of the TV,

TERMINALS ON THE BACK OF

THE CABLE BOX

--I

Connect the cable from the

antenna or cable system to the

Input terminal on the back of the

CABLE BOX.

VCR

4/ TOVCR {_O r[' ._J]o 4

Incoming Cable from

Antenna or Cable TV

System

_)INPUT r_ OUTPUT

(_OUTPUT _QG_

SVIDEO VIDEO L-i_UI_3-R

Note:

When the antenna cable is connected to the TV antenna terminal via a cable box or VCR, set the TV

channel to CH3 or CH4, cable. This does not apply when signal is input from VIDEO INPUT.

Connections

Cable cover removal and fitting

FittingRemoval

1. Disengage the claws at

the uppermost end.

2. Slowly pull out in the

upward direction.

1. Insert the claws (at 2

points) at the bottom.

2. Push in the TOP.

Note:

Dependingonthetypeofcableuseditmaynotbe possibletoclosethecover,Insuchcasesthecabtemaybe routed

throughthe antennacover,

How to connect the input/output terminals

Connect camcorder and video game console.

INPUT

COMPONENTVIDEO

o o

00 ÷

GO÷

CAMCORDER

VIDEO GAME CONSOLE

(Optional)

S-VIDEO cable

VIDEO cable

t t t

Connections

Connect VCR and other peripheral equipment

INPUT

212

COMPONENT VIDEO

INPUT

1 2

®@

VIDEO VIDEO

©©

AUDIO AUDIO

®®

____ ,super-VRSVOR,

0 .0000(30

[]

®® ®®® @

Audio Audio Video S Video

L IN R L OUT R OUT OUT

$ ,!, $ $ $ _-

S-VIDEO

cable

VIDEO

AUDIO

l_ ;innectionexample

INPUT1connection

INPUT2 connection.

Connect the

S-VIDEO or

VIDEO

Terminal

Connection example

component VIDEO

INPUT1 connection

component VIDEO

INPUT2 connection.

(DVD/STB)

o ,,0(30 (30

% []

COMPONENT VIDEO OUT A_io

L OUT R

Y Pb Pr

®®®®®

,I,

VIDEO

AUDIO

Notes:

eWhen connecting video cables, priority is given to the S-Video cable when the S-Video input terminal

and the video input terminal are connected at the same time.

OThe volume control output of the LCD TV will be fixed.(SOUND,ADJUST, VOLUME UP/DOWN and

SURROUND ON/OFF are not functional for output signals from the AUDIO OUT terminals.)"

I How to connect the HDMI Terminal

HDMI _1(HDMI : High Definition Multimedia Interface) isthe first all digital consumer electronics A/V interface

that supports uncompressed standard. One jack supports both video and audio information.

This HDMI '_`_input can be connected to an EIA/CEA-861/861B `_2compliant consumer electronic device,

such as a Set Top Box or DVD player equipped with HDMI or DVI output connection.

By inputting a High-bandwidth Digital Content Protection (HDCP) high-definition picture source to the HDMI

terminal of this television, high-definition pictures can be displayed on the screen in their digital form.

Audio Cable

(not included) y _j

I f

I If the external device has DVI output only, use a HDMI-DVl

conversion cable .3 to connect to the HDMI jack on the LCD.

Also, connect the Audio out signal from the external device.

(Set Top Box or DVD player) to the AUDIO IN'_4jacks beside

the HDMI input.

HDMI Cable (not included)

HDMI or DVI

signal out

Set Top Box

DVD player

......................... s

Applicable VIDEO Signal

This model support following format.

Please adjust the format of connecting equipment.

No. of dots (H x V)

1080i

480P

480i

Vertical scanning frequency(Hz)

1,920 x 1,080i 59.94/60

720 x 480P 59.94/60

640 x 480P 59.94/60

720(1,440) x 480i 59.94/60

This input terminal is not intended for use with computers.

AUDIO signal (L.PCM)

When the digital sound signal is included at connecting HDMI equipment, L.PCM sound is available.

Sampling frequency

48KHz / 44.1KHz / 32 KHz

Notes:

(1) This HDMI connector is Type A.

(2) If you cannot display the picture because your Digital Set Top Box does not have a Digital OUT terminal

Output setting, use the component Video input (or the S video Input or Video Input). In this case the picture

will be displayed as an analog signal.

_-1. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks

of HDMI Licensing LLC.

:_-2.EINCEA-861/861B profiles compliance covers profiles for transmission of uncompressed digital video

including high bandwidth digital content protection.

:_-3.HDMI-DVI conversion cable part no. (TY-SCH03DH):available on Panasonic Website (USA only)

(www.panasonic.com)

¢-4.AUDIO-IN, Please refer to page 24. (HDMI-IN)

Power ON / OFF

Connecting the Plug to the Wall Outlet

Note:

The TV's power cord must first be plugged intothe wall outlet.

How to Turn the Power On

Main POWER switch

l__

'_POWER /VIDE0 VOLUME C+HANNEL 1

SAPC)

RETURN

MENU EXIT

0 C)

Press the Main POWER switch on the top of TV to turn

the set on.

POWER-ON: Green

When the set is on or in standby mode press the Main

POWER switch on the TV to turn the set off.

POWER-OFF: No light

Example: The screen below is displayed for a while after

the TV is turned on. (setting condition is an

example.)

ZOOM

CH 6

SAP

MONO

_ Press the POWER button on the remote

control to turn the TV off: Red (standby)

Press the POWER button on the remote

control to turn the TV on: Green

Note:

The TV willstill consume some power as long as the power

cord is stillplugged into the wall outlet.

I Location of Controls I

Illuminated Remote Control

Power button ,-

Press to turn the TV ON or OFF.

Note: The TV's power cord must first be plugged into the walt outlet and

then turned on at the POWER switch (standby mode).

Mode Selection buttons

VCR Mode Selection for Remote

Control

Digital Broadcasting Satellite for Remote

Control / Cable TV Mode Selection for

Remote Control

TV Mode Selection for _ _ _

Remote Control

---- Digital Video Disc Mode

Selection for Remote Control

R-TUNER-TUNE button '

L.) Switches to previously viewed channel or video mode.

Operation of other Device

VCR VCR REW/FF

CABLE/DBS

DVD Skip Search REW/FF

PLAY

Pause

STOP

on s

Device

VCR

CABLE/DBS

DVD

VCR RECORD TV/VCR Switch VCRCH up/down

-- STB--ASPECT PAGE up/down

-- Open / Close Slow/+/-

ASPECTASPECT button

_)R Change of screen size (See page 20).

r JUST-_-_ ZOOM _ FULL _ NORMAL_

Location of Controls

S, hu.on --1

Selects Audio mode (See page 24).

STEREO _ SAP -_ MONO

Changes to the next channel up

Moves cursor upward during menu mode,

O O

RECALL MUTE GUIDE

0 0 0 0

® ®®

® ® ®--

® ® ®

nEW pLAY FF

PAUSE STOP REC

&SPECT

TVNCR VCRIDBSCH

Moves cursor to

the left during

menu mode.

Displays menu

Press to access

TV, DTV, DBS or

DVD menus.

Changes to the next

channel down

Moves cursor downward

during menu mode.

Moves cursor to

the right during

menu mode.

Return

to previous

MENU or EXIT

from menu.

The input mode changes each

time this button is pressed.

TVNIDEO RECALL

C) C>

Press this button to mute the

sound, press again to cancel the

mute

MUTE GUIDE

O O GUIDE button

U___ for DBS.

Press to display the current system status, for example, Aspect

mode, Channel number, Stereo mode, Picture menu, TV/VIDEO,

Power save, Off timer and Color system.

Direct program number

selection buttons

SLEEPPROG dash button / SLEEP TIMER button

P(_ Program dash channel numbers for DTV and DBS,

Sleep timer (MINUTES)

_-_0---* 3o--* 6o-_- 9o

[

I FIow Chart of MENU

All adjustments and setting functions available in this set can be made using the menu buttons.

The menu screen is composed of 2 menus: the ADJUST menu and the SET UP menu.

Press to display MENU

screen, press again to

clear.

PICTURE

ru PICTURE ADJUST

[_E] POSITION / SIZE

AUDIO

J_ AUDIO ADJUST

O VOL

EXIT

TV/VIDEO RECALL MUTE GUIDE

0 0 0 0

®® ®

® ® ®

SLEEP

R-TUNE PROG

o ® ®

Please refer to the On Screen Help

An On Screen Help box is displayed whenever a menu is displayed

on the "IV. This Help box indicates which keys onthe remote control

are used to navigate the menu shown. See above for descriptions

of button functions.

ON SCREEN HELP

'Instruction' box LANGUAGE

MENU selection

PICTURE

PICTURE ADJUST !

POSITION / SIZE I

AUDIO

J_ AUDIO ADJUST

I_) LANGUAGE t

_E] PROGRAM OH

_1 LOCK I

CLOSED CAPTION I

INPUT LABEL

"_ OTHER ADJUST

I I

SET UP

lid LANGUAGE I [

!_3PROGRAM CH I

LOCK I

rd_CLOSEDCAPTIONI <_

I;=_INPUTLABEL 1

"_ OTHER ADJUST I

Flow Chart of MENU

Press to select the desired MENU (ADJUST or SET UP).

Press to select each item.

Press to display each adjustment screen.

Proceed to the adjustment.

• To return to previous screen :

RETURN

EXIT

G- Press to return.

• To end adjustments :

Q - Press to exit from the MENU screen.

This returns the set to the normal viewing condition.

Press to display each

adjustment screen.

,©

RETURN

Press the RETURN

button to return to

previous screen.

TO PICTURE ADJUST

PICTURE

(See page 21)

TO LANGUAGE

TO PROGRAM

CHANNELS

TO AUDIO ADJUST

(See page 24)

TO LOCK

selection screen

Press to display each Allows you to select the

adjustment screen, language used for On

O K Screen Displays.

j Q [_> r ENGLISH'='_'FRAN_;AIS"I

i. "-ESPAI_IOL'-- J

RETURN TO CLOSED

[ ] CAPTION

Press the RETURN

button to return to

previous screen.

(See page 29)

(See page 18,19)

TO OTHER ADJUST

screen

VIDEO NR

3D Y/C

COLOR MATRIX

POWER SAVE

(See page 30)

BLOCK PROGRAMS

CHANGE SE]-i-ING

ENTER CODE FIRST

(See page 25)

TO INPUT LABEL

selection screen

(See page 30)

I Tuningchannels(Automatic channel programming) I

Automatically scans all TV channels and stores them in memory.

Turn the Power on and press the TV/VIDEO button to display the TV channel.

Press the MENU button to display the MENU screen and select SET UE

Press to select PROGRAM CH.

Press to display the PROGRAM

CHANNELS screen.

Press to select MODE.

Press to select TV or CABLE.

SET UP

LANGUAGE J

PROGRAM CH I

I_ LOCK I

CLOSED CAPTION I

r-_ INPUT LABEL I

"_ OTHER ADJUST I

Press to select AUTO PROGRAM.

Press to display the confirmation

screen.

Press to select YES.

__ Press to select NO.

Press to run AUTO PROGRAM.

Channels will automatically advance until all channels have been

scanned. Channel numbers with a video signal present will be stored

in the Channel Scan Memory.

Press to exit from the MENU screen.

This returns the set to the normal viewing condition.

Notes:

• When buttons are pressed with AUTO PROGRAM running, the TV set will return to normal viewing.

(Channels searched up to this point are added.)

• After AUTO PROGRAM is finished, the lowest channel number added will be received.

• When there are no receivable channels, channel 69 is displayed for TV and channel 125 is displayed

for cable TV.

I Tuning channels (Manual channel programming)

Use this setting when changing setting of receiving channels or changing the channel display.

Turn the TV on and select the broadcast channel. Follow the steps on the previous page to display the I

PROGRAM CHANNELS screen.

Press to select MANUAL PROGRAM.

Press to display the MANUAL

PROGRAM screen.

Adding or deleting channels

Press to select channel

(or number keys).

Press to add channels to memory (Channel

number turns blue).

Press to delete channels from memory

(Channel number turns yellow).

Repeat steps 2 and 3 to continue adding or deleting channels.

Press to exit from the MENU screen.

This returns the set to the normal viewing condition.

I ASPECT Controls

The color monitor will allow you to enjoy viewing the picture at its maximum size, including wide screen

cinema format picture.

o ® ®

REW PLAY FF

F---qr_-I r_l

PAUSE STOP REC

nn r--_ rr_

VCR_I)BS CH

ASPECT

TV/VCR

ASPECT button

The aspect mode changes each time the ASPECT button

is pressed.

F-. JUST-_ ZOOM _ FULL _ NORMAL_

Note:

When a 1080i signal is being received, the mode is set to

FULL, and aspect switching is not possible.

NORMAL

JUST

ZOOM

FULL

I-- 4 _1 I,._.-t 6_

3 °]-,4a !

o oi [

4 _1 I-._16_

o o[

Normal mode will display a 4:3 picture

at its standard 4:3 size.

JUST mode will display a 4:3 picture

at its maximum size but with aspect

correction applied to the sides of the

screen so that elongation is only

apparent at the left and right edges of

the screen. The size of the picture will

depend on the original signal.

ZOOM mode magnifies the central

section of the picture.

FULL will display the picture at its

maximum size but with slight

elongation.

I Picture Adjustments

Press the MENU button to display the

MENU screen and select ADJUST.

__ _ Press to select

PICTURE

ADJUST.

ADJUST

PICTURE

PICTURE ADJUST I

L_] POSITION / SIZE I

AUDIO

AUDIO ADJUST J

Press to display the PICTURE

ADJUST screen.

Press to select the menu to adjust.

Select the desired level by looking at

the picture behind the menu.

NORMAL is displayed at default.

AI PICTURE

PIC MODE

PICTURE MODE is stored for TV, VIDEO1, VIDEO2, COMPONENT1,

COMPONENT2 and HDMI individually.

_- STANDARD_ CINEMA"_,'- VIVID

MODE Function

STANDARD Displays standard image.

CINEMA Ideal for watching movies in a dark room.

VIVID Displays a clear screen with contrast of light and dark.

BACK LIGHT, PICTURE, BRIGHTNESS, COLOR, TINT, SHARPNESS, AI PICTURE, COLOR TEMP

You can change the level of each Item (BACK LIGHT, PICTURE, BRIGHTNESS, COLOR, TINT,

SHARPNESS, AI PICTURE and COLOR TEMP) for each MENU (STANDARD, CINEMA, and VIVID )

according to your personal preference,

Item Function

BACK LIGHT Luminance of the back light is adjusted.

PICTURE Selects proper brightness and density for the room.

BRIGHTNESS Adjusts for easier viewing of dark pictures such as night scenes.

COLOR Adjusts the level of color.

TINT Adjusts for flesh tone color.

SHARPNESS Adjusts the degree of sharpness.

AI PICTURE Displays black and white colors more clearly when turned ON.

COLOR TEMP Increase or decrease WARM (red) and COOL (blue) colors to suit personal

preference.

• To reset to standard setting :

Press to select

NORMALIZE.

Press OK.

Picture Adjustments

ADVANCED ADJUST

Press to select PIC MODE.

Select STANDARD or CINEMA.

PICTURE

Press down to PAGE 2 and select

ADVANCED ADJUST.

Press to select ADVANCED

ADJUST ON.

Press to go to NEXT PAGE.

ADVANCED ADJUST will be shown.

MPEG NR

Press to select the menu to adjust.

Select the desired level by looking at

the picture behind the menu.

NORMAL is displayed at default.

Item Function

BLACKEXTENSION Contrast level will be improved.

WHITE CHAR CORR It makes white characters brighter.

MPEG NR Noise unique to DVD, STB etc will be reduced.

Position / Size Adjustment

This function will adjust the picture position / size for easy viewing.

Press MENU button to display MENU screen

and select adjust.

Press to select POSITION/SIZE.

Press to display POSITION/SIZE control.

ADJUST

PICTURE

PICTURE ADJUST I

[] POSITION / SIZE J

AUDIO

I_ AUDIO ADJUST J

2 [Picture Position Adjustment ]

Itwill work for "ZOOM" mode only.

Press to move picture vertically for the best view.

[ Picture Size Adjustment ]

I,f

Itwill work for "NORMAL" and "JUST" mode only,

_ Press to select.

size 1: reduced black bar.

size 2: widened black bar.

-- Size1

Size2

• To return to previous screen :

RETURN

EXIT

G-- Press to return.

• To reset to standard setting : o=._

Press OK.

I Audio Adjustments

Press the MENU button to display the MENU screen and select ADJUST.

Press to select AUDIO ADJUST.

Press to display the AUDIO ADJUST

screen.

ADJUST

PICTURE

[_ PICTURE ADJUST [

POSITION / SIZE I

AUDIO

AUDIO ADJUST I

Press to select the menu to adjust.

Select the desired level by listening

to the sound.

NORMAL is displayed at default.

MODE

[--_ AUTO_ STANDARD_ DYNAMIC

MODE

AUTO

STANDARD

DYNAMIC

Function

Automatically adjusts quiet sound

and loudsound for easeof listening.

Emits the original sound.

Gives contrast to sound.

BASS, TREBLE, BALANCE, SURROUND

You can change the level of each Item ( BASS,

TREBLE, BALANCE and SURROUND ) for each

MODE (AUTO, STANDARD and DYNAMIC )

according to your personal preference.

Item Function

BASS Adjusts low sounds

TREBLE Adjusts high sounds

BALANCE Adjusts left and right volume

SURROUND Toenjoy a concert hall effect,

turn SURROUND to ON when a

stereo signal isavailable.

Selecting STEREO/SAP/MONO

STEREO _ SAP _ MONO

Note:

Red display : With signal

White display : No signal

White display : MONO

MODE Function

STEREO Two c.hannel Audio reception.

Second Audio Programming

SAP ( typically used for bilingual audio ).

MONO Use when stereo signal is weak.

HDMI IN

Perform input switching of analog audio input (for DVI) and digital audio input (for HDMI) when using

the HDMI terminal.

_'- AUTO_ DIGITAL 4---,-- ANALOG

AUTO Set use of analog audio input when digital audio signal is not available.

DIGITAL Forces use of digital audio input signal transmitted via the HDMI terminal.

ANALOG Forces use of analog audio input signal transmitted via separate RCA terminals.

I Lock Feature

In the United States, the V-CHIP consists of two rating systems, which are MPAA

(MOTION PICTURE) and TV PARENTAL GUIDELINES. Its function is to block programs

by the rating data in the XDS data packets sent from broadcasting stations. The user

can select which rating programs should be blocked by the LOCK MENU options.

0 0 0 0

Looo®i

®®®1

Press the MENU button to display the MENU screen and select SET UP.

Press to select LOCK.

Press to display the

LOCK screen.

Input code

Enter any 4-digit number as a password.

These numbers will be needed when

deactivating the LOCK function.

While entering a code, by pressing the

up _ or down _ buttons you can

input a new code again.

After entering your secret code for the first time, the onscreen

display will change to CHANGE CODE. And you can change the

Input code.

Note: Use a code that is easy to remember and record it in a

safe place.

Selecting broadcasts to lock.

Press to select BLOCK PROGRAMS.

Pressto select U.S MOVIES, U.S. TV

PROGRAMS, CANADIAN ENGLISH

or CANADIAN FRENCH.

U.S. MOVIES "_" U.S.TV PROGRAMS "=-'-_]

ADIAN ENGLISH"=_"CANADIAN FRENCH_

Press to select STATUS.

Press to select ON or OFF.

Press to select CHANGE SETTING.

Press to display the next screen.

STATUS

Lock Feature

for U,S.TV PROGRAM to lock

Press to select VIEW NR PROGRAMS?.

Press to select NO or YES.

NO : Cannot view programs with NR signals.

YES : Can view programs with NR signal.

Press to select SEr-FING.

Press to select BASIC or DETAILED.

_" BASIC-.=-_ DETAILED "_

Press to select rating.

BASIC: Change the selected title.

DETAILED :The cursor selecting the title

can be moved to select options

displayed on the right.

Press to lock or unlock the rating.

Lock: Red

Unlock : Green

_:[][][][]

Locking and unlocking

• When a title field is selected, all ratings below this rating are selected.

• When options within an option field are selected, ratings below this rating within the same field are

selected.

• Ratings displayed in green are unlocked and those displayed in red are blocked programs.

1. Ratings for children: These ratings are divided into ranks as follows.

I _[_-_'_1 TV-Y7-FV J

[TV-Y71 I FV

2. Ratings for teenagers: These ratings can be created out of these major categories to form vadous

combinations. These combinations are described in the below diagram. Ratings for all ages are on

top and ratings for adults are on the bottom.

• To return to previous screen :

• To end adjustments :

RETURN

EXIT

G Press to return.

Press to exit from the MENU screen.

This returns the set to the normal viewing condition.

Lock Feature

for U.S.MOVIES to lock

Press to select VIEW NR PROGRAMS?.

Press to select NO or YES.

NO : Cannot view programs with NR signals.

YES : Can view programs with NR signal.

Press to select rating.

Press to lock or unlock the rating.

Lock: Red

Unlock : Green

Rating

G : General audience

PG : Parental guidance suggested

PG-13 : Parental guidance needed

under 13 years otd

R : Restricted

NC17 : No one under 17 is admitted

X : Pornography

for CANADIAN ENGLISH / CANADIAN FRENCH to lock

Press to select VIEW E PROGRAMS?.

Press to select NO or YES.

Press to select rating.

Press to lock or unlock the rating,

Lock: Red

Unlock : Green

Lock Feature

CANADIAN ENGLISH RATINGS CHART

Exempt - Exempt programming includes:news, sports, documentaries and other information

E programming, talk shows, music videos, andvariety programming.

C Programming intended for children under age 8. No offensive language, nudity or sexual

content.

C8+ Programming generally considered acceptable for children 8 years and over. No profanity,

nudity or sexual content.

G General programming, suitable for all audiences.

PG Parental Guidance suggested. Some material may not be suitable for children.

Programming contains themes or content which may not be suitable for viewers under

14+ the age of 14. Parents are strongly cautioned to exercise discretion in permitting viewing

by pre-teens and early teens.

18+ years old. Programming restricted to adults. Contains constant violence or

18+ scenes of extreme violence.

CANADIAN FRENCH RATINGS CHART

E Exempt - Exempt programming.

General - Programming intended for audience of all ages. Contains no violence, or

the violence content is minimal or is depicted appropriately.

8+ General - Not recommended for young children. Programming intended for a broad

8 ANS+

audience but contains light or occasional violence. Adult supervision recommended.

Programming may not be suitable for children under the age of 13 - Contains either a

13ANS+ few violent scenes or one or more sufficiently violent scenes to affect them. Adult

supervision strongly suggested.

16ANS+ Programming may not be suitable for children under the age of 16 - Contains frequent

scenes of violence or intense violence.

18+ years old. Programming restricted to adults. Contains constant violence or

18ANS+

scenes of extreme violence.

RETURN

EXIT

• To return to previous screen : (_-

Press to return.

• To end adjustments :

_-- Press to exit from the MENU screen.

This returns the set to the normal viewing condition.

Closed Captions

This unit has a built in decoder that provides a visual depiction of the audio portion

of a television program in the form of written words across the screen (white or

colored letters on a black background). It allows the viewer to read the dialogue of

a television program or other information.

Press the MENU button to display the MENU screen and select SET UP.

Press to select CLOSED CAPTION.

Press to display the CLOSED

CAPTION screen.

SET UP

[Ik_ LANGUAGE

I_ PROG_MCH

I1_1 LOCK

CLOSED CAPTION

I_::::_iNPUT LABEL

I'_ OTHER ADJUST

[_ ON MUTE

Activates the On-Screen Closed Caption feature, when the MUTE button on the Remote Control is

pressed. To deactivate, press the MUTE button again.

Note:

This feature functions when the Closed Caption Mode is in the "OFF" position.

The program being viewed must be broadcast with Closed Caption.

Press to select [_ ON MUTE.

Press to select from the following:

_---_NO (OFF)'_'_'" C1''--'_ C2"_

3 MODE

Activates the On-Screen Closed Caption feature. When activated this feature will remain on until

OFF is selected in this menu.

Press to select _ MODE.

f __

o_-_ -o_-"_ I_ Press to select from the following:

€ CAPTION OFF -

• CAPTION C1 -

• CAPTION C2 -

Recommended mode when Closed Caption is not being used.

For video related information that can be displayed (up to 4 lines of scriptstrategically

placed on the television screen so that it does not obstruct relevant parts of the picture).

Another mode used for video related information.

• To return to previous screen :

• To end adjustments :

RETURN

EXIT

(_-- Press to return.

(_-- Press to exit from the MENU screen..

This returns the set to the normal viewing condition.

I Customizing the VIDEO INPUT labels I

Display for each VIDEO INPUT can be changed to match with the connected device

(VCR, DVD Player etc.).

Press the MENU button to display the MENU screen and select SET UP.

Press to select INPUT LABEL.

Pressto display the INPUT LABEL screen.

Press to select the VIDEO INPUT.

E_ COMPON ENT1 ,_-_b COMPONENT2 -_-]

HE)MI '_-_ VlDEO2 ,.w,------_Vl DEO1

Press to change the INPUT LABEL.

Each INPUT LABEL has the following choices.

IOID LANGUAGE I

II_ PROGRAM CH I

l t:i LOCK I

tr_ CLOSED CAPTION I

INPUT LABEL .--.I

I'_ OTHER ADJUST I

HDMI

F COMPONENTI(COMPONENT2, VIDEO1,VIDEO2or HDMI).--_ VC R

-[BLANK]= --DTV: =DVD" m'_'_AME _"_

OTHER ADJUST

Pressthe MENU button to display the MENU screen and select SET UE

Press to select OTHER ADJUST.

Press to access OTHER ADJUST.

Press to select the item that you would

like to change.

Press to select desired condition.

VIDEO NR

Reduce video noise in the picture.

Selection condition: ON4._.__OFF

3D Y/C FILTER

Minimizes noise and cross color in the picture.

Not available for COMPONENT VIDEO.

Selection condition: ON..,_--.._OFF

SET UP

I_ LANGUAGE I

If_ PROGRAM CH I

Ia LOCK I

I_a CLOSED CAPTION I

[_:::_INPUT LABEL _1

°_ OTHER ADJUST I

VIDEO NR

3D Y/C

COLOR MATRIX

POWER SAVE

li]'Jll!

COLOR MATRIX

Displays input signals (480p signals) in a natural color.

Automatically adjusts color parameters for HD (high definition) and SD (standard definition).

Selection condition: SD _ HD

POWER SAVE

The POWER SAVE will be suitable for watching at night and power consumption will be reduced.

selection condition: STANDARD--SAVING

I OperatingperipheralequipmentusingtheremotecontrolI

ProgrammingTheIlluminatedRemoteControlUsingAccessCodes

The Universal Remote Control can be programmed to operate many manufacturers' components, using the

component function buttons for TV, VCR, DBS/CABLE or DVD. Follow the procedures for programming

your Remote Control with or without a code for the component.

Determine the manufacturer of the component and look in the table for the code.

Confirm that the external component is plugged in and operating.

Turn the component off.

Press POWER and OK together, for at least 5 seconds.

After 5 seconds, all the illuminated mode keys will begin to flash.

Release the POWER and OK keys.

Press the mode key.

The mode key will illuminate steadily, all others will go out.

®®®1

Enter the 3-digit component code using the Remote Control numeric

keypad.

Press the Remote Control to test the component. If the

procedure is successful, the component will turn on.

Default Modes For Remote Control

VCR

DBS/CBL

DVD

TV (Panasonic Only)

VCR (Preset)

DBS (Preset), CABLE (Preset)

DVD (Preset)

Panasonic TV Codes

Panasonic VCR Codes

Panasonic DBS Codes

Panasonic DVD Codes

Helpfui Hints: UnsuCCessful _ .....

If the component does not operate with the Remote Control, repeat the procedure using

another code. (Some brands have multiple codes).

If an incorrect code is entered, or if the procedure takes longer than 30 seconds,the

programming will fail.

Operating peripheral equipment using the remote control

ProgrammingWithoutACode(Whenthecodeisnotknown)

This procedure searches all codes and is called the "sequence method."

]VNID_O RECALL MUTE GUIDE

0 0 0 0

I® ® ®1

I®®®1

R_ pLAy FF

PAUSE STOP REC

nn c_n r'_

ASPECT

TVNCR VC_$CH

_ 2 Turn the component off.

Confirm that the external component is plugged in and on.

Press POWER and OK together,

for at least 5 seconds.

After 5 seconds, allthe illuminated

mode keys will begin toflash.

Release the POWER and OK key.

Press the mode key.

The mode key will illuminate

steadily, all others will go out.

Press to move forward to the next

code, or to move backward.

Press the Remote Control _ to test the component. If the

procedure was successful, the component will turn on.

Note:

Repeat the above steps until the component code isfound. It may

take many attempts before the correct code isfound.

After the code isfound, press OK to

store the code.

Note:

The step and set mode willstart from the current device (not the

beginning of the list, except for the first time).

Operating peripheral equipment using the remote control

Infrared Codes Index

The remote control is capable of operating many brands of peripheral equipment. Refer to pages 31 and 32

for programming procedures.

Note: The remote control memory is limited and therefore some models may not operate. The remote

control is not designed to control all features available in all models.

Note: After entering the proper infrared code, press the desired Mode Selection Button on the remote control.

Refer to pages 14 and 31 - 32 for details on operating peripheral equipment using the remote control.

Helpful Hint: Write down the code numbers for your components in the space provided below. This will serve as a

handy reference whenever you need to reprogram your remote control.

CABLE _ VCR DBS

Other Component Other Component Other Component

- [o]7t;FJI

;odes for VCR

Admiral

Aiwa

Akai

Audio Dynamic

Bell &Howell

Broksonic

Canon

Citizen

Craig

Curtis Mathes

Daewoo

DBX

Dimensia

Emerson

Fisher

Funai

Goldstar

Gradiente

Hitachi

InstantReplay

Jensen

JVC

Kenwood

LXI

Magnavox

Marantz

Marta

Memorex

MGA

Minolta

Mitsubishi

Multiteeh

NEC

Olympic

Optimus

335

332

314,315,316, 329

311,339

305,313

320,326

323,325

306

305,306,329

324, 345

301,324,343

310,311,339

345

303, 319, 320, 325, 326,343

305,307,308,309,313

320,326,334

324,333, 345

306

334

300,323,345

323, 324

339

310, 311,334, 339

306, 310,311,339

300,305,306,307,308,309

323, 324, 331

310, 311,339

306

309, 324

338, 340, 341,347, 348

300, 345

338, 340, 341,347, 348

304,347

310, 311,334,339

323,324

306,321,328,335

Odon

Panasonic

J.C.Penney

Pentax

Philco

Philips

Pioneer

Proscan

Quasar

Radio Shack

RCA

Realistic

Samsung

Sansui

Sanyo

Scott

Sears

Sharp

Shintom

Signature 2000

Singer

Sony

Sylvania

Ta_hiro

Tatung

Teac

Technics

Teknika

Toshiba

VectorResearch

Wards

Yamaha

Zenith

320, 326

321,322, 323, 324

300, 305, 310, 311,324,

339, 345

300, 311,345

320, 323, 324, 326, 331,343

323, 324, 331

323

300, 301,302, 323, 324,

331,333, 345, 346

321,322, 323, 324

305, 309, 324, 333, 336, 340

300, 301,302, 323, 324,

331,333, 345, 346

305, 309, 324, 336, 340

302, 304, 333

320, 326, 339, 352

305, 369, 313

301,302, 304, 309, 320,

326, 338, 340, 347, 348

300, 305, 306, 307, 308

335, 336

317

335

;317

i328, 329, 330

323, 324, 331

306

310, 311,339

321,322, 323, 324

324

301,346

311

306, 309, 335, 336, 344

305, 310, 311,339

306, 344

Codes for Personal Video Recorders

100

101

102

Operating peripheral equipment using the remote control

Codes for DVD

_ I Ferguson

JVC

Mitsubishi

Nordmende

Panasonic

Philips

Pioneer

RCA

100

101

t09

105

101

100

103

102

101

Saba 101

Samsung 110

Sharp 108

Sony 104

Technics 1O0

Thomson 101

Toshiba 103

Yamaha 100

Zenith 107

Codes for Cable Box

ABC

Archer

Cableview

Citizen

Curtis

Diamond

Eagle

Eastem

GC Brand

Gemini

General

InstrumenVJerrold

Hamlin

Hitachi

Macom

Magnavox

Memorex

Movietime

Oak

Panasonic

Philips

Pioneer

Pulsar

124

125,132

105,132

105,122

112,113

124,125,132

129

134

108,132

122

111,119,120,121,122,

123,

124,125,126,127

112,118,140,141,142,

145

103,124

103,104,105

133

130

105,132

102,137,139

109,110,1!4

106,107,128,129,130

101,116

105,132

Poser

RCA

Realistic

Regal

Regency

Rembrandt

Samsung

Scien_cAtlanta

Slmark 101,

Sprucer 105,

Stargate 105,

Teleview 101,

Texscan 144

Tocom 135

Toshiba 104

Unika 125,

Universal 122,

Videoway 106

Viewstar 129,

Zenith 100,

Zenith/Drae 100

Satellite

132

115

132

112, 118, 140, 141,142,

145

134

105, 132, 137

105

111,112, 113

105

110

132

105

132

130

117

Codes for DBS

Dish Network

(Echostar)

Echo Star

Express VU

G.E.

G.I.

(GeneralInstrument)

Gradiente

Hitachi

HNS (Hughes)

105,115,116

105

105,115

106

108

114

103, 111, 112

103

Panasonic

Philips

Primestar

Proscan

RCA

Sony

Star Choice

Toshiba

Uniden

102

104

101,102

108

106,109,110,113

107

103,108

100

101,102

Operating peripheral equipment using the remote control

Mode Operational Key Chart

This chart defines which keys are operational after programming (if needed), while in the selected remote

control mode TV, DTV, CABLE, DBS, VCR, DVD ...etc.

SAP

MUTE

TV/_,'IDEO

2__'I:]HI_ ,v,[+]i] =IR

POWER

TV MUTE

TV INPUT SW

CABLECHANNEl.

UP/DOWN

ENTER

CABLE VOL + / -

mill :_._LV,[e]m]a

POWER

STBAUDIOTRACK

STB MUTE

"IV INPUT SW

STBNAVIGATION

UP/DOWN

STB ACTION

STB NAVIGATION

RIGHT/LEFT

STB MENU

_ I;m,v,[+]m]_

POWER

SAP ON/OFF

MUTE

TV INPUT SW

CHANNEL

UP/DOWN

ACTION

VOL+/-

DISPLAY

EXIT

mu, i[_;B,v,[+]m]=_

POWER

TV MUTE

TV INPUT SW

TV CHANNEL

UP/DOWN

TV ACTION

TV VOLUME +/-

RECALL ONSCREEN VCR

(_) - - DISPLAY

O - STB EXIT -

GUIDE

(_ - STB GUIDE -

Select Channel

Select Channel Select Channel

0©0

®®®

0®®

Select Channel

li]Yjt] _',{i]I]_| J_,Yt+l.|

POWER

TV MUTE

TV INPUT SW

,NEXT/PREVIOUS

CHAPTER

NEXT/PREVIOUS

CHAPTER

TV VOLUME +/-

R-TUNE PREVIOUS CHAN

0 OR VIDEO MODE iCABLEPREVIOUS STB PREVIOUS - -

SLEEP

PmOG STB PROGRAM/

(_) SLEEP - DASH - -

REW FF SKIP SEARCH

[-_ [_ - - VCR REW/FF <<REW/>>FF

PLAY

I_ - - - PLAY PLAY

PAUSE

- - - PAUSE PAUSE

STOP

- - - STOP STOP

REC

r_ - - - VCR RECORD -

ASPECT

TV/VCR

0 ASPECT - STBASPECT TVNCR SWITCH OPEN/CLOSE

vc_c_sc. VCR CHANNEL

(_ - - PAGE UP/DOWN UP/DOWN SLOW +/-

Manuel de instrucciones [Resumen]

Estimado cliente de Panasonic

Bienvenido a la familia de clientes de Panasonic.

Esperamos sinceramente que disfrute durante inuchos a_os de su nuevo televisor

LCD.

Para obtener el mc'tximo beneficio de su aparato, lea estas instrucciones antes

de hacer cualquier ajuste, y gu6rdelas para poder utilizarlas como referencia

en el futuro.

Guarde tambi_n el recibo de su compra, y anote el n_mero del modelo y el

n_mero de serie de su aparato en el espacio provisto en la cubierta posterior de

estas instrucciones.

I Preparacibn

Instalacibn de las pilas en el control remoto

Cambio de las pilas

Cambie las pilas siguiendo los pasos indicados mds abajo:

Se necesitan dos pilas AA.

1. Abra la cubierta de las pilas. 2. Instalelas pilascomose muestraene[ 3. Vuelva a colocar la cubierta.

compartirnientode laspilas.

(l_aspolaridades+ y- debera ncoincidir

con tas marcas correspondientesdel

compartimiento).

Dos pilas

_'_. tamafioAA

/_ Precauciones relacionadas con la utilizacibn de las pilas

La instalaci6n incorrecta de las pilas puede causar fugas en las mismas que podrian estropear el

transmisor de mando a distancia.

Tome las precauciones siguientes:

1. Utilice siempre pilas nuevas cuando reemplace las viejas.

2. No intente cargar, cortocircuitar,desarmar, calentar o quemar las pilas usadas.

3. Las pilas deberdn cambiarse cuando el mando a distancia funcione esporadicamente o no pueda

controlar esta unidad.

Conexibn

Conexi6ndelcabledeantenaalterminaldeentradadeRF

Conexi6n de antena - Para recibir correctamente los canales de VHF/UHF se requiere una antena externa.

Para obtener la mejor recepcion se recomienda utilizar una antena para exteriores.

El modo de antena debe ajustarse a TV.

Antena de VHF Antena de UHF

Cable coaxia! ._

de 75 ohmios

de antena

(ANT o VHF/UHF)

_ lavija de antena

coaxial

Desmontaje e instalacibn de la cubierta de la antena

Ganchos

(_ Desmontaje

1.Empuje los ganchos hacia arriba y tire ligeramente de la

cubierta hacia usted mismo para soltar las garras (en 4

puntos).

2.Saque lentamente la cubierta hacia abajo.

(_ Instalacibn

1.1nserte las garras (en 4 puntos) en el extremo de la parte

superior.

2.Empuje la cubierta hasta que !os ganchos hagan un ruido

seco.

Nota:

Para evitar que aparezcan interferenciasen la panta!la, nojunte el cable de la antena y el cable del adaptador

de CA.

Conexidn de antena / cable

Cable entrante de 75 ohmios procedente de la antena del hogadcompa6ia de televisi6n por cable

Conexi6n de cable - Para recibir loscanales

de televisibn por cable (01 - 125) conecte el

cable suministrado por su compafi_'a de

televisi6n por cable. El modo de antena debe

ajustarse a CABLE. (Consulte la seccibn

Modo de la antena.)

Adaptador de antenatipo F (nosuministrado)

ANT(VHF/UHF) _)_

en laparte posteriordeltelevisor

Nota:

Ciertossistemasdetelevisi6nporcableneutralizanalgunoscanalespara reducirintefferenciaso tienencanalesespeciales

(codificados).Pararecibircorrectamenteestoscanales se necesitaun sintonizadorde conversibnde televisi6nporcable.

P6ngaseen contacto consu compafiia de televisi6n porcable para conocer losrequerimientosde compatibilidad.

Conexion

Para quitar y colocar la cubierta del cable

Para quitarla

1.Suelte los ganchos del

extremo mAs alto.

2.Sa,quela lentamente hacia

arriba.

Para colocarla

1.Inserte los ganchos (en 2 puntos)

en el extremo mas bajo.

2.Empujela hacia adentro en el

extremo m_.s alto.

Nota:

Dependiendo del tipo de cable utilizado, tal vez no sea posible cerrar la cubierta. En tales casos, el cable

podra instalarse a trav_s de la cubierta de ta antena.

Como conectar el t_rmino del entrada/salida

Reproducci6n en una videograbadora o en otro equipo perif_rico

cable S-VIDEO

VIDEO

AUDIO

cable S-VIDEO

cable VIDEO

Estereof6nico

] •

VideograbadoraSuper-VHS

Video camara

JUEGO DE VIDEO

DVD/STB

AUDIO

Notas,

OCuando se conecten cables de video, y cuando se encuentren hechas conexiones al mismo tiempo al

terminal de entrada de S-video y al terminal de entrada de video, se dar_. prioridad al cable de S-video.

eel control de salida de sonido es fijo (SONIDO, AJUSTE, VOLUMEN subir/abajo Y Ambiente conexi6n/

desconexi6n son no funciona para el terminal de Audio Out).

Conexibnldesconexibn de la alimentacibn ]

Conexibn de la clavija a la toma de corriente

Nota:

El televisor y el adaptador de CA consumir&n algo de energ{a siempre que el cable de alimentacion est_

conectado a la toma de corriente.

Cbmo conectar la alimentacibn

Interruptor POWER principal

t , i•

|=_']gl[=lt,]=I_

RETURN

MENU EXIT

0 0

Presione el interruptor POWER principal del televisor para

encenderlo.

POWER-ON: Verde

Cuando el aparato este en el modo de alimentaci6n

conectada o en espera, pulse el interruptor POWER

principal del televisor para apagarlo.

POWER OFF: Apagado

Ejemplo:La pantalla de abajo se visualiza durante un rato

despues de encenderse el televisor. (La condici6n de ajuste

es un ejemplo.)

ZOOM Canal 6

SPA

MONO

_ Pulse e!bot6n POWER del mandoa distancia

para apagar el televisor: Rojo (espera)

Pulse el bot6n POWER del mando a distancia

para encender el televisor:Verde

Nota:

El cable de la alimentaci6n del televisor deber_

enchufarse primero al tomacorriente, y el televisor

encenderse luego con el interruptor POWER (modo de

espera).

I Ubicacibn de los controles

Control remoto iluminado

Botbn de la alimentaci6n

P_lselo para encender o apagar el televisor.

Nota: El cable de la alimentacion del televisor deber_, enchufarse primero

al tomacorriente, y el televisor encenderse luego con el interruptor

POWER (modo de espera).

Botones de selecci6n de modo

Seleccion del modo de --

videograbadora para el

control remoto

Sat_lite de emision digital para el control

remote

Selecci6n del modo de televisi6n por

cable para el control remoto

Selecci6n del modo de _ _ _

televisor para el control

remoto

'_ elecci6n del modo de disco

de vfdeo digital para el

control remoto

R-TUNEBoton R-TUNE

(,_ Cambia al canal o modo de vfdeo anterior.

Funcionamiento de otro dispositivo

Videograbadora

CABLE/DBS

DVD

Rebobinado/avance rapido

de videof)rabadora

Busqueda con salto en

rebobinado/avance r_pido

Reproducci6n

Pausa

Parada

_Botones I

Apara_

Videograbadora Grabaci0ndevide0grabad0ra

CABLFJDBS

DVD

Conmutaci6n de

:televisorNideoqrabadora

ASPECTO de STB

Abertura/cierre

Subida/ba ada de canal

para vid_ oqrabadora

UP/DOWN de P_.gina

Lentamente/+/-

ASPECTBot6n ASPECT

TVNCR

(_ Cambia el tamaSo de la pantalla (consulte la pdgina 20).

_- JUSTIFICADO _ ACERCAMIENTO _ COMPLETO _ NORMAL_]

Ubicacion de los controles

3 G

TVNIDEO RECALL MUTE GUIDE

0 0 0 0

BotGn SAP

Selecciona el modo de audio.

y ESTEREO _ SPA _ MONO --1

Cambia al siguiente canal superior

Mueve el cursor hacia arriba durante el modo

del men_.

Mueve el cursor

hacia la izquierda

durante el modo del

mene.

Presione para

acceder a los

men_s DTV, DBS

o DVD.

Mueve el cursor

hacia la derecha

durante el modo

del menQ,

-Presione para

votver MENU

anterior o salir de

MENU.

Cambia al siguiente canal

inferior

Mueve el cursor hacia abajo

durante el modo del menU.

® ® ®

® ®®

® ® ®

El modo de entrada cambia

cada vez que se presiona

este botGn. I

TV/VlDEO RECALL

O O

REW PLAY FF Presione para visualizar la hera, el canal, el cronometrados de

_ _ _ apagado y otras opciones.

_ [-_ @ -- Botonesdeseleccibndirectade

_.SPECT ndmeros de programas

TVNCR VCR/DBS CH

_ { O (_ (_ /-- SLEEP Bot6n PROG raya/Bot6n Ternporizador de cancelado

PROG

_iG (_) Programa nl3meros de canales para DTV y DBS.

Temporizador de cancelado (Minutos)

[--_ 0 "_ 30 _ 60 -_ 90 7

Presione este boton para silenciar

el sonido, y pi31selode nuevo para

cancelar el silenciamiento.

MUTE GUIDE

(_ (_ BotGn GUIDE

L__ para DBS.

I Organigrama de mends de televisi6n

Utilizando los botones del menu se pueden hacer todos los ajustes y configuraciones que este aparato es

capaz de realizar. La pantalla de menQ est'. compuesta de 2 menus, el menQ Ajuste y el menu Configu.

PQIselo para visualizar la

pantalla MENU, y pulselo

de nuevo para cancelada.

SAP

vo,O

EXIT

TVNIDEO RECALL G_

®®®

® ® ®

® ®®

SLEEP

R-TUNE PROG

o ® ®

Consulte la ayuda en pantalla

El cuadro de ayuda en pantalla se visualiza siempre que aparece

un menu en la pantalla. Este cuadro de ayuda indica que teclas

del mando a distancia se utilizan para desplazarse pot el men_

mostrado. Consulte m_.sarriba las descripciones de las funciones

de los botones.

Cuadro de instrucciones

de ayuda en pantalla

Seleccion de MEN0

IO Idiema

_3 Pr_. Oanales

a Bio_ueo I

I_ Subtitulos

[:::= Por_a Titulos

"3o Otto AiuSte I

I I

Configu.

Idioma I I

_E3 Prowl.Canales I

_1 Bloqueo I

G Subfltulos

1:= Ponga Tltulos I !

"_ OtroAjuste I

[

Organigrama de mends de television

Pulse para seleccionar el MEN0 deseado (Ajuste o Configu).

Pulse para seleccionar cada elemento.

Pulse para visualizar cada pantalla de ajuste.

Prosiga con el ajuste.

RETURN

EXIT

• Para volver a la pantalla antedor :Q Pulse para volver.

• Para finalizar el ajuste :

Pulseparasalirdela pantallaMENU.

Estohacequeel aparatovuelvaa la condici6ndevisi6nnormal.

Pulse para visualizar cada

pantalla de ajuste.

,©

RETURN

1 5{ ]

Pulse el bot6n

RETURN para volver

ala pantalla antenor.

Men[_

Ajuste Imagen

Luz de Arras

Normalizar

(consulte la pagina 21)

Men=3

Ajuste Sonido

(consulte la pa.gina 24)

Menl3 Idioma

Men0 Pantalla de selecci6n

Prog.Canales Bloqueo

Pulse para visualizar

cada pantalla de Le permite seleccionar el

ajuste, idiomaseleccionadoen las

O K visualizacionesen pantalla.

] 0 [_> E-_SEH_FcR'/_N(_AISG

RETURN

Pantalla e ajuste

] _ I ] Subtftulos

Pulse el bot6n

RETURN para volver

a la pantalla anterior.

I_ ISi

I[SOl'Jll

(consulte la pagina 28)

(consulte la pdgina 18,19)

MenLi

Otro Ajuste

REDUC DE RUIDO

Filtro 3D

Matriz Color

ECON ENERGIA

(consulte la p_igina 30)

P,og

INGRESAR CLAVE

consulte la p_.gina 25)

Ponga Tftulos

(consulte la p&gina 30)

Sint0nizacibndecanales(Pr0gramacibnaut0maticadecanales)I

Explora autom_ticamente todos los canales de TV y los almacena en la memoria.

Conecte la alimentacion y pulse el bot6n TV/VIDEO para visualizar el canal de televisi6n.

Pulse el boton MENU para visualizar la pantalla MENU y seleccione

Configu.

Pulse para seleccionar Prog. Canales.

oK Pulse para visualizar la pantalla

Prog. Canales.

Pulse para seleccionar MODO.

Pulse para seleccionar TV o CABLE.

Configu.

Idioma I

I_ Pro_. Canales I

a Bloqueo I

Subt{tuios I

Pon_aTltulos I

"_ OtroAjuste I

Pulse para seleccionarPROGRAMAAUTO.

Pulse para visualizar la pantalla de

confirmacion.

Pulse para seleccionar Si.

Pulse para seleccionar No.

Pulse para ejecutar PROGRAMAAUTO.

Los canales avanzar_n automaticamente hasta que todos hayan side

explorados. Los nt_meros de canales con una videosefial se

almacenar_,n en la memoria de exploraci6n de canales.

Pulse para salir de la pantalla MENU.

Esto hace que el aparato vuelva a la condici6n de visi6n

normal.

Notas:

• Cuande se pulsen botones mientras se ejecute PROGRAMAAUTO, el televisor volver_, al modo de visibn

normal. (Los canales encontrados hasta este punto se a_adir_.n.)

• Despu@s de terminar PROGRAMA AUTO, se recibira, el canal con el numero ma.s bajo que haya sido

a5adido.

• Cuando no haya canales que puedan ser recibidos se visualizar,_ el canal 69 (canal 125 para la televisi6n

por cable).

t Sintonizacibndecanales(Programaci6nmanualdecanales)I

Utilice este ajuste cuando cambie ajustes de los canales de recepci6n o cuando

cambie la visualizaci6n de los canales.

Encienda el televisor y seleccione el canal de emision. Siga los pasos de la ps.gina anterior para I

visualizar la pantalla Prog. Canales.

Pulsepa_ seleccionarPROGRAMA

MANUAL.

Pulseparavisualizarlapantalla

PROGRAMA MANUAL.

Adicion o borrado de canales

Pulse para seleccionar canal

(o teclas de numeros).

Pulse para afladir canales a la memoria

(el nQmero del canal se pone de color azul).

Pulse para borrar canales de la memoria

(el nt_mero del canal se pone de color

amarillo).

Repita los pasos 2 y 3 para continuar afiadiendo o borrando canales.

Pulse para salir de la pantalla MENU.

Esto hace que el aparato vuelva a la cendici6n de visi6n

normal.

I Troubleshooting

Before requesting service for this LCD TV, check the chart below for a possible cause of the problem you

are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and

restore proper operation. If you are in doubt about some of the check points, or if the remedies indicated in

the chart do not solve the problem, consult your dealer for instructions.

Symptom Cause and remedy pag_

Power supply does not go • Is power supply plug unplugged from the outlet?

on • If power will not go on with the remote control, is the power supply of the TV "Off"? 12

Remote control cannot be • Is battery exhausted, or is battery polarity wrong? 7

operated • Isthe remote control receiver illuminated with strong light from a fluorescent lampetc.?

• Are you using the special-purpose remote control for this equipment? (The unit

will not operate with another remote control.)

Image shakes, or image is • Isthere deterioration, breakage or disconnection of the antenna or antenna wire?

unclear • Is the antenna wire connected correctly? 8, 9

There are spots on the ° Is the system affected (by radio wave interference or induced electromagnetic

picture, or the screen waves) by external sources (automobiles or trains, high-voltage wires, neon,

shakes motors, magnetized steel frame, or iron rain shutters, etc.)?

,-,Turn off the power supply, and try changing the equipment setup location. If

that has no effect, separate magnet-proofing will be required.

The image appears doubled • Is the antenna direction shifted?

or tripled ° Are reflected electromagnetic waves being received from mountains or buildings?

A color pattern appears, or ° Is the equipment being affected by another TV (electromagnetic interference)?

colors disappear ,,,,Changing the TV setup location may lead to improvement.

The channel number ° Has the RECALL button been pressed?

disappears from the screen _ Press the "RECALL button" again.

If the system is switched to external input and there is no external signal video, -

the number will disappear.

When the image is net stable, • This occurs when the signal driving the liquid crystal is lost, and is not a

the screen turns completely malfunction. 15

white for a moment

Thescreengoesdarkmomentarily •The screen is darkened for a moment to conceal noise generated when changing

whenthe channelischanged, channels.

The TV makes a hissing • If the screen and audio are not abnormal, this sound is caused by slight

noise occasionally expansion and contraction of the cabinet due to changes in room temperature. -

It has no effect on performance.

The screen display shakes • When input is switched to "video input", this may occur if there is no signal at

with video input the video/audio input terminal.

A black band appears ° This is due to noise generated when changing channels.

momentarily when selecting 10, 11

channels with video

Both edges of the screen, or • They may appear bent due to the received channel or some DVD software.

columns or window frames, This is not a malfunction.

appear bent

The image from the connected •Are p_ugs securely inserted into each terminal?

equipment does not appear --Securely insert plugs all the way. 10,11

The main unit is hot to the I • The main unit radiates heat, so some parts of the console reach a high

touch temperature. This is not a problem for performance or quality.

• Set up at a location with good ventilation.

Do not cover the ventilation holes of the console with a tablecloth, etc., and do

not place on top of other equipment (like a video deck).

Poor Video • Check HDMI cable is connected securely.

H (Example: Snow noise, no • Turn the power supply of the TV set and connected equipment ON/OFF

picture, picture runs, etc.) • Check compatibility of connected signal. Change settings of connected

D equipment to make signal compatible. 12

M • Is the input source from the equipment that is EIA/CEA-861/861B compliant

consumer electric device?

I Poor Audio • Set audio of connected equipment to L.PCM.

• Check setting of HDMt INPUT under AUDIO ADJUST. 24

• If the problem with the digital audio connection persists, change to an analog

audio connection.

I Specifications

Power Source AC 120 V, 60 Hz

Average use : 92W

Power Consumption Stand-by condition : 1.3 W

TV set DC 15V, 1.6 A max.

LCD 559 mm (22-inch), 16 : 9 aspect ratio LCD panel

487.7 mm (19.20 ") (W) x 274.3 mm (10.80 ") x

Screen Size

559.5 mm (22.03 ") (DIAGONAL)

Channel Capability VHF-12 : UHF-56 : Cable-125

Sound

Speakers

Full-range

Woofer

I Headphones

FEATURES

Operating Conditions

Connection Terminals

INPUT

COMPONENT

VIDEO INPUT

OUTPUT

HDMI

Dimensions ( W x Hx D )

Including TV Stand

TV Set Only

Mass (Weight)

3W + 3W + 5W (10 %THD)

4 cm, 2 pcs

_5cm, 2pcs

M3 (3.5 mm) Jack x 1

CLOSED CAPTION

V-Chip

Temperature : 41 °F - 95 °F (5 °C - 35 °C)

Humidity : 5 % - 90 % RH (non-condensing)

VIDEO (RCA PIN Type x 1) x 2

S-VIDEO (MINI DIN 4pin × 1) x 2

AUDIO L-R (RCA PIN Type x 2) x 2

Yx2

PB/PRX2

AUDIO L-R (RCA PIN Type x 2) x 2

AUDIO L-R (RCA PIN Type x 2)x 1

1.0 Vp-p (75 _)

Y :1 Vp-p(75_). C:0.286Vp-p(75Q)

0.5 Vrms

1.0Vp-p (including synchronization)

_+0.35Vp-p

0.5 Vrms

HDMI TYPE A Connector x 1

586 mm (23.07") x 427.5 mm (16.83 ") x 255 mm (10,04 ")

586 mm (23.07 ") x 387.2 mm (15.25 ") x 91.3 (3.59 " mm)

9.5 kg (20.9 lb.) NET

Note:

Design and Specifications are subjectto change without notice.Weight and Dimensions shownare approximate.

Customer' Record

The model number and serial number of this product can be found on its rear panel. You should

note this serial number in the space provided below and retain this book, plus your purchase

receipt, as a permanent record of your purchase to aid in identification in the event of theft or

loss, and for Warranty Service purposes.

Model Number

Serial Number

Panasonic Consumer Electronics

Company, Division of Matsushita

Electric Corporation of America

One Panasonic Way Secaucus

New Jersey 07094

Panasonic Sales Company,

Division of Matsushita Electric

of Puerto Rico Inc, ("PSC")

Ave. 65 de Infanteria, Km 9.5

San Gabriel Industrial Park,

Carolina, Puerto Rico 00985

Panasonic Canada Inc.

5770 Ambler Drive

Mississauga, Ontario

L4W 2T3

MBS0703S0

Panasonic TC-22LH1 El manual del propietario

Marca: Panasonic

Modelo: TC-22LH1

Tipo: El manual del propietario

Descargar PDF

informe

En otros idiomas

English: Panasonic TC-22LH1 Owner's manual

Panasonic TC-22LH1 El manual del propietario

Panasonic TC-22LH1 El manual del propietario

En otros idiomas

Documentos relacionados

Otros documentos