Panasonic PVD4745S Manual de usuario

Marca: Panasonic

Modelo: PVD4745S

Categoría: Reproductores de DVD

Tipo: Manual de usuario

PV-D4735S

DVD/VCR DECK

Operating Instructions

Model No.

Connections and Initial Setup Procedures are on pages 12 to 17.

Please read these instructions carefully before attempting to connect,

operate or adjust this product. Please save this manual.

Spanish Quick Use Guide is included.

(Guía para rápida consulta en español está incluida.)

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

LSQT0907 A

MULTI FORMAT PLAYBACK

Ability to play back may depend on recording conditions.

For Your InformationVCR Operation DVD OperationBasic OperationInitial Setup

As an ENERGY STAR Partner, Panasonic Corporation of North

America has determined that this product or product model meets the

ENERGY STAR guidelines for energy efficiency.

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:161

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from a power source indicated on the unit or in this

manual. If necessary, have your Electric Utility Service

Company or Video Products Dealer verify the power source in

your home.

2 POLARIZED OR GROUNDING PLUG

As a safety feature, this product comes with either a polarized

power cord plug (one blade is wider than the other), or a three-

wire grounding type plug.

POLARIZED PLUG CAUTION:

This plug will only fit into an outlet one way. If you cannot fully insert

the plug, try reversing it. If it still will not fit, have an electrician

install the proper wall outlet. Do not defeat the safety feature by

tampering with the plug.

GROUNDING PLUG CAUTION:

This plug will only fit into a three-hole grounding outlet. If necessary,

have an electrician install the proper outlet. Do not defeat the safety

feature by tampering with the plug.

3 POWER CORD

Make sure power cords are routed so that they are not likely to

have anything rest on them, roll over them, or be in the way of

walking traffic. If an extension cord is used, make sure it also

has either a polarized or grounded plug and that the cords can

be securely connected. Frayed cords, damaged plugs, and

damaged or cracked wire insulation are hazardous and should

be replaced by a qualified service technician.

Overloaded outlets and extension cords are fire hazards and

should be avoided.

4 DO NOT BLOCK VENTILATION HOLES

Ventilation openings in the cabinet release heat generated during

operation. If they are blocked, heat build-up inside the unit can

cause failures that may result in a fire hazard or heat damage to

cassettes or discs.

For protection, follow these rules:

a. Never cover ventilation slots or the unit while in use, or

operate the unit when placed on a bed, sofa, rug, or other

soft surface.

b. Avoid built-in installation, such as a book case or rack,

unless proper ventilation is provided.

5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS OR

SUDDEN TEMPERATURE CHANGES

Do not place the unit over or near heater or radiator, in direct

sunlight, inside closed vehicles, in high temperature [over 104°F

(40°C)], or in over 75% humidity. If the unit is suddenly moved

from a cold place to a warm one, moisture may condense in the

unit and on the tape causing damage. Never subject the unit to

vibration, impact, or place it so that the surface is tilted as

internal parts may be seriously damaged.

6 TO AVOID PERSONAL INJURY

• Do not place unsecured equipment on a

sloping surface.

• Do not place this unit on any support that

is not firm, level, and adequately strong.

The unit could fall causing serious injury

to a child or adult and damage to the unit.

• An appliance and cart combination should

be moved with care. Quick stops, excessive force, and

uneven surfaces may cause the appliance and cart

combination to overturn.

• Carefully follow all operating instructions and use the

manufacturer's recommended accessories when operating

this unit or connecting it to any other equipment.

USING THE UNIT

If the unit has been in storage or moved to a new location, refer first to the

INSTALLATION section of these safeguards.

1 KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.

2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR STRONG

IMPACT, unplug the unit and have it inspected by a qualified service technician

before use.

3 DURING AN ELECTRICAL STORM

During a lightning storm, whether indoors or outdoors, or before leaving the unit

unused for extended periods of time, disconnect all equipment from the power

source as well as the antenna and cable system.

4 WHEN THE UNIT IS PLUGGED IN

• Never expose the unit to rain or water. DO NOT OPERATE if liquid has been

spilled into the unit. Immediately unplug the unit, and have it inspected by a

service technician. Fire and shock hazards can result from electrical shorts

caused by liquid contact inside.

• Never drop or push any object through openings in the unit. Some internal parts

carry hazardous voltages and contact can cause electric shock or fire hazard.

Do not put any foreign object on the disc tray.

• Avoid placing the unit directly above or below your TV set as this may cause

electrical interference. Keep all magnets away from electronic equipment.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire,

shock, or other hazards.

6 CLEANING THE UNIT

Unplug the unit. Then, use a clean, dry, chemically untreated cloth to gently

remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that

could over-spray, or seep into the unit and cause electrical shock. Any substance

such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to

greasy, humid, or dusty areas may adversely affect internal parts.

SERVICE

1 DO NOT SERVICE THIS PRODUCT YOURSELF

If, after carefully following the detailed operating instructions, this product

does not operate properly, do not attempt to open or remove covers, or make

any adjustments not described in the manual. Unplug the unit and contact a

qualified service technician.

2 IF REPLACEMENT PARTS ARE REQUIRED

Make sure the service technician uses only parts specified by the

manufacturer, or those having the same safety characteristics as the original

parts. The use of unauthorized substitutes may result in fire, electric shock,

or other hazards.

3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK

After any service or repairs to the unit, request the service technician to

conduct a thorough safety check as described in the manufacturer’s service

literature to ensure that the unit is in safe operating condition.

Important Safeguards and Precautions

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL

ELECTRICAL CODE

OUTDOOR ANTENNA INSTALLATION

1 SAFE ANTENNA AND CABLE CONNECTION

If an outside antenna or cable system is connected to the equipment, be sure the

antenna or cable system is grounded so as to provide some protection against

built up static charges and voltage surges.

Section 810 of the National

Electrical Code, ANSI/NFPA 70

(in Canada, part 1 of the Canadian Electrical

Code) provides information with respect to

proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an

antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes and requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR

CIRCUITS

An outside antenna system should be located well away from power lines,

electric light or power circuits and where it will never come into contact with

these power sources if it should happen to fall. When installing an outside

antenna, extreme care should be taken to avoid touching power lines, circuits or

other power sources as this could be fatal. Because of the hazards involved,

antenna installation should be left to a professional.

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO

THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL

WARNINGS IN THE MANUAL AND ON THE PRODUCT.

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:162

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol warns the user that uninsulated voltage within the unit may

have sufficient magnitude to cause electric shock. Therefore, it is

dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the

operation and maintenance of this unit has been included.

Therefore, it should be read carefully in order to avoid any problems.

Safety Precautions/Mesures de sécurité

To prevent fire or shock hazard, do not expose this equipment to rain

or moisture.

To prevent electric shock, match wide blade of plug to wide slot, fully insert.

AVERTISSEMENT:

Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas

exposer cet appareil à la pluie ou à une humidité excessive.

ATTENTION:

Pour éviter les chocs électriques, introduire la lame la plus large de la

fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.

THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE

HAZARDOUS RADIATION EXPOSURE IF DIRECTED.

BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE

YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER

OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

CAUTION:

LASER RADIATION

WHEN OPEN. DO NOT

STARE INTO BEAM.

ATTENTION:

RAYONNEMENT

LASER EN CAS

D’OUVERTURE.

NE PAS REGARDER

DANS LE FAISCEAU.

(Inside of product)

FCC NOTE:

This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference when operated in a

residential environment. If this equipment does cause interference to radio or television reception,

which can be determined by turning the equipment off and on, use the equipment in another

location and/or utilize an electrical outlet different from that used by the receiver.

If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find

the booklet, “Something About Interference” available from FCC local regional offices helpful.

FCC Caution:

To assure continued compliance, (example- use only shielded interface cables when connecting

to other devices.) Any changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate this equipment.

Region Management Information:

This DECK is designed and manufactured to respond to the

Region Management Information that is recorded on a DVD

disc. If the Region number described on the DVD disc does

not correspond to the Region number of this DECK, this

DECK cannot play this disc.

● The Region number for this DECK is “1”.

● The Player will play DVD-Video marked with labels

containing “1” or “ALL”.

Example:

ALL

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:163

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Before Using

Congratulations

on your purchase of one of the most

sophisticated and reliable products on the

market today. Used properly, it will bring you

years of enjoyment. Please fill in the information

below. The serial number is on the tag located

on the back of your DECK.

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.

PV-D4735S

• Serial No.

Only use tapes with the mark in this DECK.

Record/ Playback Time

(Standard Play)

SLP

(Super Long Play)

Type of Video Cassette

Tape Speed

Setting

T180T160T120

2 Hours

40 Minutes

2 Hours

6 Hours 8 Hours

3 Hours

9 Hours

Accessories

RF Coaxial Cable

LSJA0418

Batteries 2 “AA”

Remote Control

EUR7724KE0

To order accessories,

call toll free

1-800-332-5368.

Video Head Clog Sensor

During playback, this screen

appears if clogging is detected.

To remove screen, press PLAY

on the remote or DECK.

Playing older or damaged tapes may eventually

cause video heads to become clogged.

Head Cleaning

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.

Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your

nearest servicenter by visiting our Web Site

(see p. 61).

Digital Auto Picture

Automatically controls the video output signal for

less noise depending on the tape condition.

Digital Auto Tracking

Continuously analyzes the signal and adjusts for

optimum picture quality.

Manual Tracking Control

(to reduce picture noise)

Use during Playback and Slow Motion mode to

reduce picture noise.

Press CH (TRACKING) / on the remote control

or on DECK until the picture clears up.

To return to Auto Tracking, press POWER off, then

on again a few seconds later.

V-Lock Control (to reduce picture jitter)

In Still mode, CH (TRACKING) / operate as a

V-Lock control.

Features for a Quality Picture (VCR)

Cleaning DECK

Use a soft cloth or dusting attachment of a vacuum

cleaner to remove dust from the ventilation holes on

the back sides and bottom of the cabinet.

Plastic surfaces are easily scratched and can be

marred by alcohol and various solvents.

Avoid excessive use of oil-based furniture polishes

since the materials used in the cabinet will

accumulate more dust. We recommend using a

non-abrasive, antistatic cleaner and polisher.

Loading the Batteries

Battery replacement caution

• Do not mix old and new batteries.

• Do not mix alkaline with manganese batteries.

1) Open cover.

3) Close cover.

2) Insert batteries as

marked.

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:164

Table of Contents

Timer Recording ................................................................. 24, 25

MTS Broadcast/ VHS Hi-Fi Stereo System ....................... 26, 27

Multi-Brand Control Feature .............................................. 28, 29

Tape Operation (Search System) .......................................... 30 ~ 32

Special VCR Features ........................................................ 33, 34

Copying Your Tapes (Dubbing) ............................................................ 35

Important Safeguards and Precautions ............................... 2, 3

Before Using ...............................................................................4

DECK & Cassette Information .............................................. 6 , 7

Location of Controls .......................................................... 8 ~ 10

On Screen Displays / Light-up Indicators............................... 11

Connections ..................................................................... 12 ~ 15

Initial Setup for Basic Connections (Ready to Play) ............. 16, 17

Reset Language, Channels, Clock, VCR’s Output Channel ........ 18, 19

Playback/ Record on a Tape.............................................. 20, 21

Initial Setup (Connection)

DVD / VCR

Basic Operation

VCR

DVD

Basic DVD Operation ......................................................... 22, 23

VCR Operation

Disc Operation .................................................................. 36 ~ 41

DVD-RAM Operation (DVD-RAM only) .................................... 42, 43

DVD Operation using On-Screen Displays .................... 44 ~ 48

MP3/JPEG Playback Operation ....................................... 49 ~ 51

Settings for DVD Operation ............................................. 52 ~ 55

Language Code List .................................................................56

DVD Operation

For Your Information

Warning and Instruction Displays...........................................57

Before Requesting Service................................................ 58, 59

Limited Warranty ................................................................ 60, 61

Customer Services Directory .................................................. 61

Spanish (Español) Quick Use Guide............................... 62 ~ 69

Index .................................................................................... 70, 71

Initial Setup Basic Operation VCR Operation DVD Operation For Your Information

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:165

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

DECK & Cassette Information

Prevent Accidental Tape Erasure

Record Tab

Cover the hole

with cellophane tape.

To record again

Break off the tab to

prevent recording.

Screw driver

DVD-RAM discs

DVD-RAM discs must meet the following conditions

for this unit to be able to play them.

Type

• Non-cartridge discs

• Discs that can be removed from

their cartridges (TYPE 2 and 4)

Capacity

• 12 cm (5”) 9.4 GB (double-sided)

and 4.7 GB (single-sided)

• 8 cm (3”) 2.8 GB (double-sided)

• Remove TYPE 2 and 4 discs from their cartridges

before use, then return them when you are finished.

Read the instructions for the disc carefully.

• Some parts of the disc, for example where one program

ends and another begins, may not play smoothly.

If disc is brought from a cold to a warm

environment, moisture may form on the disc

Wipe away moisture with a soft, dry, lint-free cloth

before using disc. (See above.)

Improper disc storage

Discs could be damaged if stored or left in areas:

• exposed to direct sunlight.

• that are humid or dusty.

• near heat (i.e. heater, radiator, etc.).

Disc Handling

To clean disc surface

With a soft, damp (water only) cloth,

gently wipe from the center hole to the

outer edge as shown below. (Wiping in a

circular pattern will scratch the surface.)

• DVD-RAM, DVD-R :

Clean only with the DVD-RAM disc

cleaner available. Never use cloths or

cleaners for CDs etc.

Handling precautions

• Sticking a label on the disc may impair DVD-R playback.

• Do not attach sticker to discs. (Do not use discs with

exposed adhesive from tape or left over peeled-off

stickers.)

• Only hold disc by edges as shown below. Fingerprints,

dirt and scratches can cause skipping and distortion.

• Do not write on label side of disc.

• Never use record cleaning

sprays, benzine, thinner,

static electricity prevention

liquids, or any other solvent.

• Do not try to close disc tray when disc is not

properly placed.

Disc tray

Disc

DECK can play back discs bearing any of the

following marks:

Discs which cannot be played

• DVD with Region No. other than “1” or “ALL”

• PAL discs, DVD-ROM, DVD-Audio, DVD-RW,

DVD+R, DVD+RW, CD-ROM, CDV, CD-G, CVD,

SVCD, SACD, CD-TEXT, Divx Video Disc,

Photo-CD and MPEG4 Video Disc

[Discs Played 8cm (3") or 12cm (5")]

DVD (DVD-Video)

CD (CD-DA)

Logo Disc type

DVD-R (DVD-Video formatted

discs [finalized])

Disc formats supported by this DECK

DVD-RAM (Version 1.1 of the

Video Recording Format a

unified video recording

standard)

Notes

• Do not use irregularly shaped discs (e.g. heart-

shaped), as these can damage the unit.

• It may not be possible to play CD-R, CD-RW,

DVD-R and DVD-RAM in all cases due to the

type of disc or condition of the recording.

CD-R/CD-RW

• CD-DA format

• MP3/JPEG file

and finalized.*

*A process that allows play on compatible equipment.

Video CD

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:166

Specifications

Power Source: 120 V AC, 60 Hz

Power Consumption: Power On: Approx. 22 watts, Power Off: Approx. 0.9 watts

Video Signal: EIA Standard NTSC color

Video Recording System: 4 rotary heads helical scanning system

Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)

Tuner

Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69

CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)

Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)

Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125

Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output

Input Terminal: Audio/Video Line Input (Front)

Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)

Audio Output 2 (L), (R)

Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)

Operating Humidity: 10 % ~ 75 %

Weight: 3.7 kg (8.2 lbs.)

Dimensions: 430 (W) x 93 (H) x 255 (D) mm

16-15/16” (W) x 3-11/16” (H) x 10-1/16” (D) inch

Discs Played

(1) DVD-Video Disc 5” (12 cm) single-sided single-layer

5” (12 cm) single-sided double-layer

5” (12 cm) double-sided double-layer (one layer per side)

3” (8 cm) single-sided single-layer

3” (8 cm) single-sided double-layer

3” (8 cm) double-sided double-layer (one layer per side)

DVD-RAM Disc 5” (12 cm) 9.4 GB (double-sided) and 4.7 GB (single-sided)

3” (8 cm) 2.8 GB (double-sided)

(2) Compact Disc 5” (12 cm) disc

(CD-DA, Video CD) 3” (8 cm) disc

(CD-R/CD-RW, MP3, JPEG)

Digital Audio Output: Digital Optical Connector

Pickup: Wavelength : 655 nm (DVD), 790 nm (Video CD/CD)

Laser power: CLASS II

Note: Designs and specifications are subject to change without notice.

Definition of Terms (DVD)

Angle: Some DVD discs feature scenes simultaneously shot from different angles.

The ANGLE button can be used to view the scene from different angles.

Chapter Number:Titles are subdivided into numbered sections. You can quickly search for

a favorite scene using these numbers.

DVD: A high-density optical disc on which high-quality pictures and sound have been

digitally recorded. DVD incorporates video compression technology (MPEG II)

and high-density recording technology which allow entire movies to be recorded

with incredible playback quality.

Playback Control:With Video CD (version 2.0), scenes or information may be selected for viewing or

listening from an interactive menu that appears on the TV screen.

Subtitles: Written dialogue which appears at the bottom of the screen.

Time Number: The elapsed play time from the start of a disc or title. Use to quickly find scenes.

(May not work with some discs.)

Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.

Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks to be

quickly located.

Video CD: CD containing picture and sound with same quality level as video tape.

This DECK also supports Video CDs with playback control (version 2.0).

Initial Setup

U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098; 4,907,093; 5,315,448; and 6,516,132.

This product incorporates copyright protection technology that is protected by U.S. Patents and other

intellectual property rights. Use of this copyright protection technology must be authorized by

Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized

by Macrovision. Reverse engineering or disassembly is prohibited.

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:167

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Location of Controls

EJECT button: When this button is pressed in VCR mode, the tape is ejected.

This button is inoperative if pressed during recording.

If pressed in DVD mode, the disc tray opens or closes.

Remote Control

ZOOM

. 37

POWER

TV mode

p. 28

EJECT

OPEN

pp. 20,

PLAY

pp. 20,

VCR/TV

p. 21

ANGLE

. 37

SUB TITLE

. 36

SELECT

Bold: VCR Function /

Bold Italic

VCR and DVD Functions

Italic

DVD Function

/ Normal: Others

CHANNEL

TRACKING

V-LOCK

pp. 4, 21,

VOLUME

p. 28

PLAY LIST

. 41, 43

DVD mode

ACTION

pp. 18

, 52

SET

VCR mode

p. 28

STOP

pp. 20,

ADD/DELETE

CLEAR

pp. 19,

38, 40

NUMBER keys

REWIND

SLOW-

pp. 20,

FAST FORWARD

SLOW+

pp. 20,

PAUSE

STILL

pp. 20,

Virtual Surround Sound (V.S.S.)

ENTER

23,

TITLE

DIRECT NAVIGATOR

. 41, 42

AUDIO

(SAP / Hi-Fi)

pp. 27,

INPUT

p. 35

DISPLAY

p. 11,

RETURN

. 22,

SPEED

p. 21

RECORD

p. 21

COUNTER RESET

p. 30

PROGRAM

p. 24

SKIP+

SKIP-

. 23

TAPE POSITION

STATUS

p. 32

COMMERCIAL SKIP

ZERO SEARCH

p. 30

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:168

Audio/Video

Input Connector 2

(LINE 2)

p. 35

CHANNEL /

TRACKING/V-LOCK

pp. 4, 21

POWER

OPEN/CLOSE

STOP/EJECT

p. 20

Light-up

Indicators

p. 11

REC

p. 21

Disc Tray

Cassette

Compartment

PLAY

p. 20

Remote

Sensor

Front View of DECK

STOP

Bold: VCR Function

Italic

DVD Function

Bold Italic

VCR and DVD Functions

Normal: Others

PLAY

If the disc cannot be removed...

First, unplug DECK. Then, prepare a rigid

wire (e.g. an extended paper clip) and,

applying moderate force, insert it straight

into the hole at the base of the tray.

The tray will eject a little. Now, pull the tray

all the way out and remove the disc.

Over 2 inches

Returns to factory setting. Use if relocating DECK, or if Initial Setup needs to be redone.

• Make sure a tape is not inserted in the DECK.

Reset All Memory Functions

Press and hold both VCR PLAY

and CHANNEL on the DECK for

more than 5 seconds.

• The power shuts off.

Turn DECK Power on.

Perform “Initial Setup (Ready to Play)”

on page 16.

Initial Setup

REWIND

SKIP

20,

FAST FORWARD

SKIP

20,

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:169

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Location of Controls (continued)

The following table shows the status of the output jacks when in VCR or DVD mode.

Bold: VCR Function

Italic

DVD Function

Bold Italic

VCR and DVD Functions

• PROG functions on the remote are not available when using Component Video Output and

S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

Video Output

Audio Out 1

Audio Out 2

Component

Video Output

S-VIDEO OUT

VCR

DVD

YES

N/A

YES

To enjoy PROGRESSIVE SCAN video

(1). Connect

Component Video Output

to the component video input terminals of a television.

(See p. 13.)

(2). When PROGRESSIVE OUT is set to “ON” in the DVD Main Menu (p. 55), a Progressive Scan

signal is output from the

Component Video Output Connector

Notes

• The screen may shift off-center when using progressive output. Please adjust the screen

position if this occurs. (Refer to your TV manual.)

• If the television is not progressive compatible, a progressive scan picture is not available.

Connect the Video Output or S-Video Output connector (see p. 12, 13) and

set PROGRESSIVE OUT to “OFF” in the DVD Main Menu. (See p. 55.)

Rear View of DECK

AC Power Plug

S-Video Out Connector

(DVD Only)

pp.

10, 13

Component Video Output

Connector (Y, P

B, PR)

(DVD Only)

Audio Output 1

Connector (L/R)

Optical Digital Audio

Output Connector

(DVD Only)

Video Input

Connector

p. 35

Video Output

Connector

Audio Output 2

Connector (L/R)

VHF/UHF Antenna Input Terminal

p. 12

VHF/UHF Antenna Output Terminal

p.12

• While plugged into an AC outlet,

this DECK consumes 0.9 W of

electrical power in off mode.

•

Audio Input

Connector (L/R)

p. 35

•

Note

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1610

On Screen Displays / Light-up Indicators

Initial Setup

VCR Status & Clock Displays

Blank Tape/ No Signal Indications

Whenever a blank section of a tape comes

up in Play mode, or when the selected

channel has no broadcast signal with Weak

Signal Display Feature (p. 33) set to OFF,

the TV screen will turn solid blue.

Function Status

Cassette inserted

(Rec Time Remaining

is displayed in OTR

mode, e.g.“0:25”.

See p.21.)

Current Time Channel

Tape Speed

(See p. 4.)

Broadcast Audio

Being Received

(See pp. 26, 27.)

When a function button

is pressed, e.g. PLAY,

or you change channels,

and also if a cassette is

inserted, a 5-second

display appears.

Counter

To display or remove

screen shown at right,

➛➛

➛ press DISPLAY.

On Screen Displays (VCR)

Function & Channel Displays

VCR mode Indicator

Lights when output

selection is VCR mode.

Flashes in Auto Clock

Set or Channel Auto Set.

DVD mode Indicator

Lights when output

selection is DVD mode.

Light-up Indicators

Timer Indicator

Lights up when DECK is set for Timer Recording, or

when One Touch Recording (OTR) is used. Flashes

when Timer Recording is set, but a tape has not been

inserted into DECK and when a power interruption

occurs during Timer Programming.

VCR REC Indicator

Lights up during

recording. Flashes in

Rec. Pause mode.

PLAY Indicator

Lights during playback in

either VCR mode or

DVD mode. Flashes in

Still, Frame by Frame, or

Slow mode.

Light-up indicators allow easy confirmation

of current DECK function status.

<Light-up combination example>

VCR +

PLAY

VCR

REC

VCR

TIMER

VCR

TIMER

REC

DVD

PLAY

Light-up Indicator Function Status

VCR playback in progress [See p. 20]

VCR recording in progress [See p. 21]

VCR timer setting in progress [See pp. 24, 25]

VCR Timer Recording in progress [See pp. 24, 25]

DVD playback in progress [See pp. 22, 23]

VCR fast forward in progress [See p. 20]

VCR rewind in progress [See p. 20]

• For on Screen Displays in

DVD mode, see p. 44.

Note

Date

(When clock is set, a 5-second

display appears.)

VCR

➛➛

➛

REC

TIMER PLAY

➛➛

➛

➛➛

➛

PLAY

➛➛

➛

TIMER

REC VCR

➛➛

➛

➛➛

➛

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1611

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Connections

1 Disconnect antenna or cable from TV

and connect to DECK.

Basic Connections

• Connect DECK and TV with an RF Coaxial Cable

(supplied) or an AV Cable

(not supplied) as shown in the figure below.

• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher

quality picture and sound.

• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo

amplifier to DECK.

FROM

ANT.

OUT

AUDIO

IN 1

OUT

DVD/VCR DECK

VHF/UHF

VIDEO

VHF/

UHF

VIDEO

AUDIO IN

AV CABLE

(not supplied)

2 Connect DECK to TV with RF Coaxial Cable.

RF COAXIAL CABLE

(supplied)

DSS

Receiver

OUT

Note to CABLE system installer

This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the

NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper

grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as practical.

OUT

Antenna or Cable

Cable Box

■ ■

■ DECK TV

■ ■

■ DSS Receiver DECK TV

■ ■

■ Cable Box DECK TV

When using “Nut type” RF coaxial cables, tighten with

fingers only. Overtightening may damage terminals.

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1612

You CannotYou Can

• record and view

both scrambled

and unscrambled

channels if

additional

equipment is

added.

This connection

requires: two

converter boxes,

an A/B switch,

and a 2-way

splitter.

• view a channel

other than the

one selected

for any type of

recording.

• set a Timer

recording of a

channel unless

you select it on

the Cable Box.

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

IN 2IN 1

Cable Box

OUTIN

OUT 2

OUT 1

2-Way Splitter

OUT

A/B Switch

■■

■

Connect With Two Cable Boxes

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

Cable Box

OUTIN

OUT

VIDEO

AUDIO

ANT or CATV

You CannotYou Can

• record

scrambled

channels.

• view any

(including

scrambled)

channel.

• use Remote

Control to select

channels without

using Multi-brand

control feature.

ANT

CATV

VIDEO

AUDIO

OUT

Connect AUDIO OUT2 (L, R) to the AUDIO IN (L, R) of the TV. (audio input for COMPONENT or

S-VIDEO mode).

If your TV has COMPONENT VIDEO INPUT, connect to COMPONENT VIDEO OUT.

If your TV does not have COMPONENT VIDEO INPUT but has S-VIDEO INPUT, connect to

S-VIDEO OUT.

When in DVD mode, set your TV to either COMPONENT VIDEO IN or S-VIDEO IN.

Connections For DVD Only (enjoying higher picture quality)

Other Connections

Notes

DVD/VCR DECK

VHF/

UHF

Cable Box

VHF/

UHF

■ ■

■ With a Cable Box (DECK

Cable Box TV)

Initial Setup

• You can watch DVDs through the S-VIDEO or COMPONENT VIDEO, VHF/UHF OUT TO TV,

and VIDEO OUT connections to your TV. The VCR and TUNER pictures are available only

from the VIDEO OUT and VHF/UHF OUT TO TV connections to your TV.

• PROG functions on the remote are not available when using S-VIDEO OUT and COMPONENT

Video Output. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROG.

• TV must have capability to accept and display a progressive scan signal to use

PROGRESSIVE mode. Consult your TV operating instructions.

VIDEO

AUDIO

COMPONENT

VIDEO OUT

AUDIO OUT2

S-VIDEO OUT

DVD OUTPUT

P R

S-VIDEO

From DECK’s

A/V OUTPUT

DVD/VCR DECK

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1613

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Connections (continued)

Audio Connections

Ready Checklist

Turn down the volume, then turn DECK, as well as other equipment to be connected, off before

proceeding with connection.

Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely.

Read through the instructions before connecting other equipment.

Ensure that you observe the color coding when connecting audio and video cables.

■ Connecting Amplifier (2ch stereo system) [Analog connection]

Speaker

Amplifier

Speaker

AUDIO OUT2

AUDIO IN

R L

DVD/VCR DECK

Notes on audio output from the optical digital audio output connector

Enjoying digital audio output from the digital audio output connector

*1 The type of audio output from the connector can be selected by the Settings for DVD Operation.

(See p. 53.)

*2 When “LPCM(DVD)” is set to OFF in the DVD Main Menu, only 48 kHz sampling/16 bit is ouput.

When set to ON, sampling of sound quality greater than 48 kHz/16 bit is reduced to 48 kHz/16

bit. (See page 53.)

For your reference:

• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories

Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel)

sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,

DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from

the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from titles

with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic Surround

Sound Decoders please contact your local dealer.

Disc

DVD-Video

DVD-RAM

Video CD

MP3

Sound recording format

Dolby Digital

Linear PCM

(48/96 kHz 16/20/24 bit)

DTS

Dolby Digital

Linear PCM(48 kHz/16 bit)

MPEG1

Linear PCM

MP3

Optical digital audio output from connector

Dolby Digital bitstream (1 - 5.1 ch)

or PCM (48 kHz sampling/16 bit only)*

Linear PCM (2 ch)

(48 kHz sampling/16 bit only)*

Bitstream or PCM (48 kHz sampling/16 bit only)*

Dolby Digital bitstream (1 - 5.1 ch)

or PCM (48 kHz sampling/16 bit only)

Linear PCM (2 ch)

PCM (44.1 kHz sampling)

Linear PCM (44.1 kHz sampling)

PCM (It depends on the MP3 file)

Manufactured under license from Digital Theater Systems, Inc. US Pat. No’s. 5,451,942, 5,956,674,

5,974,380, 5,978,762, 6,487,535 and other US. and world-wide patents issued and pending. “DTS”

and “DTS 2.0 + Digital Out” are trademarks of Digital Theater Systems, Inc.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby Laboratories.

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1614

When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS

bitstream is output from the DECK OPTICAL digital audio output connector. When DECK

is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality

audio in your home. [An optical digital audio cable (optional) is required when an optional

Dolby Digital decoder or DTS decoder is used.]

Notes on connecting an optical

digital audio cable (optional)

• Remove the attached cap, and

firmly connect the cable to the

connector.

Caution for optical digital audio output connector:

• When connecting an amplifier (with an Optical Digital Input Connector) which does not

contain the Dolby Digital or DTS decoder, be sure to select “PCM” at “Dolby Digital” and

“PCM” at “dts” of the Settings for DVD Operation “Audio Output” (see p. 53).

Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be

harmful to your ears and damage your speakers.

• When a Dolby Digital/DTS decoder is connected, please select “Bitstream” at “dts” or

“Dolby Digital” of the Settings for DVD Operation “Audio Output”.

If “PCM” is selected, there will be stereo sound. (See p. 53.)

• Video CDs and CDs can be played as usual.

Amplifier

DVD/VCR DECK

(Rear)

Front

Speaker

Front

Speaker

Surround

Speaker

Surround

Speaker

Center

Speaker

Subwoofer

Decoder with

Dolby Digital /DTS

processing (optional)

Optical Digital

Audio Cable

(optional)

To Optical

Digital Audio

Input Connector

■ Connecting Amplifier (5.1 ch Surround system) [Digital connection]

DECK Dolby Digital Decoder Amplifier Speaker

DECK DTS (Digital Theater Systems) Decoder Amplifier Speaker

[5.1ch Surround system]

Initial Setup

• Some DTS decoders which do not support DVD-DTS interface may not work properly with DECK.

Note

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1615

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Before doing Initial Setup

Initial Setup for Basic Connections (Ready to Play)

Turn TV on.

See connections RF Coaxial Cable Connection and AV Cable Connection on page 12.

ÖSet TV to channel 3.

ÖSet TV to VIDEO.

[DECK

➛➛

➛ TV]

• Go to “Initial Setup (Ready to Play).” (See below.)

[Cable Box

➛➛

➛ DECK

➛➛

➛ TV], [DSS

➛➛

➛ DECK

➛➛

➛ TV]

• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel

in your time zone.

• If you use a DSS Receiver, it must be turned off.

Press VCR on remote for VCR mode.

Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel

and clock set starts.

• If screen below does not appear, check DECK - TV connection and, if TV is tuned to

channel 3, try switching it to channel 4.

• To change VCR’s output channel, please see “VCR’s Output Channel” on page 19.

Plug VCR Power plug into an AC wall outlet.

Initial Setup (Ready to Play)

• Function buttons are void during Initial Setup.

• To eject a tape during Auto Set, press EJECT on remote

or STOP/EJECT twice on DECK.

Then make settings manually. (See p. 18.)

• If Auto Clock Set takes more than 30 minutes,

press STOP and perform settings manually. (See p. 18.)

Notes

Continued on next page...

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1616

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Settings are made automatically.

When complete, this screen appears.

If “AUTO CLOCK SET IS INCOMPLETE” appears,

manually set clock (below).

If Auto Clock Set was incomplete.

Press ACTION* on remote to display

CLOCK screen.

Press

to select the month and SET to set.

In the same manner, select and set the date,

year, time, and DST (Daylight Saving Time).

Press ACTION to start clock and exit.

Manual Clock Set

VCR

ACTION

SET

SELECT

EJECT

STOP/EJECT

dy to Play)

Initial Setup

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1617

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Clock

2) Press to select

“MANUAL,” and press SET.

(For Auto Clock Set, select

“AUTO CLOCK SET.”)

3) Press and to

select, then set the date,

time, and DST (Daylight

Saving Time).

4) Press ACTION to start

Clock and exit this

mode.

(“TIME ZONE ADJUST”

appears only when auto

clock is set.)

Language

2) Press SET repeatedly to

change language item as

shown below.

For English

For Spanish

For French

1) Press to select

language item.

Reset Language, Channels, Clock, VCR’s O

Channels

2) Press to select

“ANTENNA,” then

press SET to set your

antenna system

(“TV” or “CABLE.”)

3) Press to select

“AUTO SET,” then

press SET.

• If you use a Cable Box,

set it to the PBS channel

in your time zone.

• After Channel Auto Set

is finished, Auto Clock

Set will be performed.

Press ACTION*

to display MENU.

3) Press ACTION to exit.

1) Press to select

“SET UP CHANNEL,”

and press SET.

1) Press to select

“SET CLOCK,” and

press SET.

• PROGRAM functions are not available

when using COMPONENT Video Output

and S-VIDEO OUT. Please set TV to

either RF INPUT or VIDEO INPUT, and

then press PROGRAM.

➡

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1618

Add or Delete a Channel

To add channel:

Select channel with NUMBER keys

and press ADD/DLT.

To delete channel:

Select channel with CH / or

NUMBER keys and press ADD/DLT.

Time Zone Adjust

2) Press to select

“TIME ZONE ADJUST,”

VCR’s Output

Channel

1) Press to select

“VCR’S OUTPUT CH.,”

and press SET.

2) Press SET.

3) Press ACTION.

After 3 seconds

• To Make Corrections,

repeat steps 1) ~ 3).

DST (Daylight Saving Time)

DECK auto adjusts clock for DST.

(p. 17.)

Spring (First Sunday in April)

DST:ON

➛➛

➛ Sets clock ahead one hour.

Autumn (Last Sunday in October)

DST:ON

➛➛

➛ Turns clock back one hour.

• If your area does not observe

Daylight Saving Time, select

DST:OFF.

• Keep these time changes in mind

when programming DECK for timer

recordings.

1) Press to select

“SET CLOCK,” and

press SET.

and press SET to

subtract or add hour(s)

as necessary.

*Important: If a remote control button does not work

when pressed, press the VCR button

on the remote and try the button again.

(Only when Auto Clock is set.)

3) Press ACTION.

•“TIME ZONE ADJUST”

returns to “0” if clock is

set manually.

➡

k, VCR’s Output Channel

Basic Operation

VCR

ACTION

SET

SELECT

POWER

NUMBER

keys

ADD/DLT

CH /

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1619

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Playback/ Record on a Tape

Ready Checklist

All connections are made. (pp. 12 ~ 15)

TV and DECK are plugged in.

TV is on and tuned to CH 3, 4, or VIDEO.

Remote is in VCR mode. (Press VCR.)

(

➛ ➛

➛ The VCR mode Light-up Indicator lights on DECK)

Playback a Tape

• These features work best in SP or SLP mode.

• The sound will be muted.

• To reduce picture noise, see “Manual

Tracking Control” on page 4.

• After 3 minutes in Still or Slow mode, VCR

stops to protect the tape and the video heads.

Notes

Insert a tape.

Playback using DECK buttons

Press PLAY.

Light-up Indicators

Press STOP/EJECT to stop

and/ or eject a tape.

VCR

DVD

EJECT

CH /

REW/

SLOW-

FF/

SLOW+

PLAY

PAUSE/

STILL

VCR/TV

STOP

REC

SPEED

Insert a tape.

• DECK power comes on. If Auto VCR/TV (see

p. 34) is set to “OFF,” press VCR/TV on the

remote for VCR mode.

• If tape has no rec. tab (p. 6), auto play begins.

• The PLAY Light-up Indicator lights on DECK.

Special Features During Play

Press PLAY* to play a tape.

Forward/Reverse Scene Search

➛➛

➛ Press FF/SLOW+ or REW/SLOW-.

➛➛

➛ Press PLAY to release.

After search has begun, each additional press

of FF/SLOW+ or REW/SLOW- changes speed

as shown below.

• Picture interruption may occur with some TVs.

• FF and REW search speed may vary depending

on current tape position.

• After 10 minutes in search mode, VCR returns to

Play mode to protect the tape and the video heads.

Notes

Press REW/SLOW- or FF/SLOW+ in Stop

mode to rewind or fast forward a tape.

Press STOP to stop a tape.

Press EJECT on remote,

or STOP/EJECT on DECK to eject a tape.

Still (Freeze) Picture

➛➛

➛ Press PAUSE/STILL.

➛➛

➛ Press PLAY to release.

Frame by Frame Picture

➛➛

➛ Press PAUSE/STILL in Still mode.

➛➛

➛ Press PLAY to release.

Slow Motion Picture

➛➛

➛ Press FF/SLOW+ (increase speed) or

REW/SLOW- (decrease speed) in Still

mode.

➛➛

➛ Press PLAY to release.

[SP] : Approx. 5X ↔ Approx. 7X

[SLP] : Approx. 11X

↔ Approx. 21X

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1620

Insert a tape with a record tab (p. 6).

• DECK power comes on. If Auto VCR/TV (see p. 34)

is set to “OFF,” press VCR/TV on the remote for

VCR mode.

Press CH , or NUMBER keys

to select the channel.

• If channel number is over 100, first press 100 key

then the other 2 digits.

• For “LINE” input, see p. 35.

Press SPEED

to select the record speed (p. 4).

SP = Standard Play

SLP = Super Long Play

Press REC

to start recording.

(The VCR REC Light-up Indicator lights on DECK),

• To edit out unwanted scenes, press PAUSE/STILL

to pause, and again to resume recording.

• You cannot view another channel during recording.

Press STOP

to stop recording.

• It is not possible to record from DVD/ Video CD/ CD

to VHS tape using DECK.

• Watching one channel and recording another is not

possible when using Cable Box or DSS Receiver.

• After 5 minutes in Pause mode, DECK stops to protect a

tape and video heads.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Record on a Tape

Remove loose or peeling labels

from tapes to prevent tape jam.

Light-up

Indicators

Record using DECK buttons

Select

Channel.

Press REC

to start

recording.

Press STOP/EJECT to stop.

This video recorder, equipped with HQ

(High Quality) system, is compatible

with existing VHS equipment.

Only use tapes with the mark.

Only tapes tested and inspected for

use in 2, 4, 6, and 8 hour machines

are recommended.

Insert a tape.

Note

Notes

One Touch Recording (recording in progress),

➛➛

➛ press REC repeatedly to set the recording length

(30 min. ~ 4 hours) (see right).

• DECK shuts off after the preset record length.

Record one station, watch another,

➛➛

➛ press VCR/TV on the remote

(change to TV mode),

➛➛

➛ select channels at TV (recording continues).

Select Channels at DECK

(In Stop or Rec. Pause mode)

➛➛

➛ press VCR/TV on the remote

(change to TV mode),

➛➛

➛ select channels at DECK.

Play a disc while recording a tape.

➛➛

➛ insert a disc during recording,

➛➛

➛ press

DVD

, and then press

PLAY

Basic Operation

Normal Rec

0:30 1:00

1:302:003:004:00

Press REC repeatedly

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1621

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Basic DVD Operation

Ready Checklist

All connections are made. (pp. 12 ~ 15)

DECK is plugged in.

If DECK is connected to an audio amplifier,

turn the stereo system’s power on.

Interactive DVD...

May include multiple camera angles,

stories, etc.

Press or

NUMBER keys

(see

below) to select title,

and press

SET

PLAY

to start playing.

Press

PLAY

to start playing.

Disc tray closes automatically.

• The PLAY Light-up Indicator

lights on DECK.

• You may also close tray by

pressing

OPEN/CLOSE

• Data reading time differs with

each disc.

• Pressing

SET

PLAY

is not necessary when

using

NUMBER keys.

Operation using DECK buttons

Press PLAY.

Insert a disc.

Press

OPEN/CLOSE.

Press STOP.6

Press

POWER.

3, 7

DVD

REW/

SLOW-

FF/

SLOW+

PLAY

PAUSE/

STILL

STOP

POWER

OPEN/

NUMBER

keys

VSS

SET

SELECT

TITLE

RETURN

Press

DVD

to select DVD mode.

• The DVD mode Light-up Indicator lights on

DECK.

• If a disc is already inserted, go to step 3.

(Depending on the disc, playback may start

automatically.)

Press

OPEN/CLOSE

and then place a disc into the disc tray.

• Hold disc by its edges

only (p. 6) with printed

side up and use guides

to place into tray.

Use 3” (8 cm)

or 5” (12 cm) disc.

DVD-RAM ➡ see p. 42

To return to menu (play stops)

Press

TITLE, MENU,

RETURN

. (DVD)

Press

RETURN

. (Video CD)

Press

STOP

to stop playing.

Press

OPEN/CLOSE

to eject the disc.

<Input

Example>

Using NUMBER keys starts play automatically.

The number of available titles varies with each disc.

1 digit number 1 •••• 1

2 digit number 12 ••• 10 ➛ 1 ➛ 2

Press

SKIP+

| or

SKIP-

| to go to next or

previous menu screen.

• SKIP function not available with all discs.

Please refer to disc jacket for operation information.

SKIP+

SKIP

Video CD with playback control...

Particular scenes or information can be

interactively selected from a menu that

appears on the screen.

If an interactive DVD*

a Video CD with playback

control*

is used and TITLE

MENU appears, go to step 4.

Cats

Samurai

Friend

Music

TITLE MENU

Cats

Samurai

Friend

Music

TITLE MENU

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1622

• Please read the disc jacket for operation information.

• If a single sided disc is placed in upside down, “THIS

TYPE OF DISC CANNOT BE PLAYED. PLEASE

INSERT A DIFFERENT DISC” is displayed.

• Remove disc and press DECK POWER off when not

in use.

• Disc continues to rotate with menu displayed even

after play is done. Press STOP to clear menu display

when finished with menu.

■ Forward/Reverse Scene Search

Press

FF/SLOW+

REW/SLOW-

during play.

Press

PLAY

to release.

• Starting forward/reverse search during play

started from menu on Video CDs may recall menu.

• Search speed, slow at first, increases with each

additional press of the button up to 5 levels.

■ Forward/Reverse Chapter/Track Skip

Press

SKIP+

| or

SKIP-

during play.

Each press skips a chapter (DVD), track (Video

CD/CD) or Program/Play List/Marker (DVD-RAM).

[DVD / Video CD / CD]

• Pressing

SKIP-

once midway through a

chapter/track returns to the start of that chapter/

track. Each additional press skips back one

chapter/track.

• Pressing

SKIP

| or | during play started

from menu on Video CDs may recall menu.

Notes

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

V.S.S. (Virtual Surround Sound)

Press

VSS

in DVD mode.

• The Surround sound effect can be changed by pressing

VSS repeatedly as shown by the figure below.

• Surround sound effect is available in DVD mode only.

• Turn off the surround effects on the other equipment.

• V.S.S. will not work, or will have less effect, with some

discs.

• Turn V.S.S. off if it causes distortion.

• Sound will only come from the two front speakers if

V.S.S. is on.

Enjoy a surround-like effect if you are using two

front speakers only. The effect is broadened

and sound seems to come from virtual

speakers on either side if the disc has surround

signals recorded on it.

Note

Power turns off after DECK has been in

Stop mode (DVD) for about 5 minutes.

Auto-Power Off Function

• When appears on the screen while a button is

being operated, it means that the corresponding

operation is prohibited by DECK or the disc.

DECK memorizes the point where STOP is

pressed (STOP is flashing on screen).

Press

PLAY

to resume play from this point.

Pressing

STOP

again or opening the tray

cancels RESUME, however, RESUME is not

canceled when power is turned off and on.

• RESUME works only with discs for which elapsed

play time is displayed during play.

• When a DVD-RAM still picture is played back, the

counter will not be displayed, however RESUME will

function.

Resume Function

■ Still Picture or Pause

Press

PAUSE/STILL

during play.

Press

PLAY

to release.

• DVD/Video CD : DECK will enter still picture mode.

• CD : DECK will enter pause mode.

■ Frame by Frame Picture (DVD/Video CD)

Press

PAUSE/STILL

in still mode.

Press

PLAY

to release.

• Each press advances picture one frame.

• Hold button down for consecutive frame advance.

• Whether pictures are advanced by “FRAME” or

“FIELD” is selected automatically. (See p. 54.)

■ Slow Motion Picture (DVD/Video CD)

Press

FF/SLOW+

REW/SLOW-

in still mode.

Press

PLAY

to release.

• Slow motion speed, slow at first, is increased

with each additional press of the button up to

5 levels.

• Reverse slow motion is not available for Video CDs.

[DVD-RAM]

• Pressing

SKIP-

once midway through a

program/play list returns to the start of that

program/play list. Each additional press skips

back one program/play list.

Reverse Skip Forward Skip

Current playback position

Chapter/Track Chapter/Track Chapter/Track

Program/Play List Program/Play List Program/Play List

Reverse Skip Forward Skip

Current playback position Marker

Basic Operation

1. Do steps 1-4 (previous page).

When menu appears, press

STOP

2. Press

NUMBER keys

to select desired track

(play begins).

• Check disc for track numbers.

• Press “1” to start at beginning of disc.

To Resume Menu use,

Press

STOP

and press

PLAY

, then the menu

will be displayed.

Now, go to step 4 (previous page).

Enjoy Video CDs featuring

playback control without using

menus (Video CDs only)

SURROUND OFF

SURROUND1

SURROUND3

SURROUND2

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1623

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Timer Recording

Press PROG*

to display Program.

Press PROG

to end programming.

DAILY

SELECT /

Selection Order

WEEKLY

(SA)

WEEKLY

(MO)

WEEKLY

(SU)

Example

Today

3) Set remaining items,

press SET

to set START/ STOP times,

CH (channel) or LINE

input (p. 35), and tape

speed (SP, SLP).

Then press

to select.

To Enter More Programs,

press

to select and

press SET

to set an unused program

number, and then repeat

step 2.

Press PROG

to exit.

Ready Checklist

All connections are made. (pp. 12 ~ 15)

TV and DECK are plugged in.

Clock set correctly. (p. 18)

Tape has record tab intact. (p. 6)

Remote is in VCR mode. (Press VCR.)

(

➛➛

➛

The VCR mode Light-up Indicator lights on DECK)

Sufficient tape remaining for recording time.

• When timer is set, the TIMER Light-up Indicator lights on DECK.

• When timer recording starts, the VCR REC Light-up Indicator lights

on DECK.

• You can set Timer Recording with the power on or off.

•“TIMER REC WILL START SOON” appears on-screen for 2 minutes

before Timer Recording starts. If DECK is in DVD mode, no message

appears, but the VCR REC Light-up Indicator will flash.

VCR

SET

SELECT

ADD/DLT

POWER

PROG

Light-up Indicators

1) Press .

2) Set record DATE,

press

to select:

1~31= one time, or

DAILY=Monday~Friday,

or WEEKLY= same time

each week.

• See selection order left.

VCR REC Indicator

VCR mode Indicator

TIMER Indicator

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1624

To Replace program...

To Clear program...

Review, Replace or Clear Program Contents:

(Recording is not in progress)

Press ADD/DLT.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Press

to select number.

To cancel a Timer

Recording in progress...

Repeat Step 2 (p. 24)

to set new programs.

Press PROG

to end the programming.

Hold down STOP in VCR mode for

a few seconds to cancel the Timer

Recording.

( The TIMER Light-up Indicator

goes out on DECK.)

• Any future daily or weekly recording

will be performed as programmed.

Notes

Press PROG

to display Program List.

VCR Operation

Important notes when using DSS Receiver

• When recording programs via DSS Receiver, DSS Receiver must be left on.

• When recording programs via an antenna or cable, DSS Receiver must be turned off.

• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to the

Cable Box input channel and Cable Box must be manually set to the desired channel.

Cable Box power must be left on.

• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER REC”

appears and TIMER Light-up Indicator flashes.

Be sure a cassette with record tab is loaded and DECK is in Stop mode.

• If a power interruption occurs while programming the timer, the timer program(s) may be

canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears

on-screen, please re-enter the timer programs.

• If the start time for Timer Recording comes up during recording and playing back,

Timer Recording will not be performed.

PV-D4735S P1-25 (041224).p65 2004/12/24, 13:1625

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

MONO broadcast

Normal monaural sound broadcast.

SAP broadcast

Secondary Audio Program (sub

language) broadcast. Select SAP

audio mode for the sub language.

MTS Stereo broadcast

Multi-channel Television Sound

Stereo broadcast. Select STEREO

audio mode.

• If stereo broadcast is weak and

display flickers, select MONO audio

mode for possible better results.

MTS Stereo and SAP broadcast

Multi-channel Television Sound

Stereo (main language) and

Secondary Audio Program (sub

language) broadcasts are being

received simultaneously.

Select STEREO or SAP audio mode.

The following are possible audio broadcast types and on-

screen displays.

The signal being received is indicated with a “

” mark while

the selected audio mode is indicated with an arrow.

Receivable Broadcast Types

MTS Broadcast/ VHS Hi-Fi Stereo System

Equipped with

-TV

Noise Reduction for

true MTS reproduction.

-TV Noise

Reduction is required

for good stereo

separation and audio

fidelity.

is a

registered trademark,

and is licensed by

Technology Licensing.

Connection

Make the Audio/Video Connection as shown on pp. 12 ~ 15.

• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.

To display the broadcast signal being received,

➛➛

➛ press DISPLAY*.

AUDIO

(SAP/Hi-Fi)

DISPLAY

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1626

VCR Operation

Audio Mode for Recording

Make a recording.

See p. 21.

Audio Mode for Playback

Start playback.

See p. 20.

• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound.

Standard stereo tapes will playback in monaural sound.

• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to a stereo

TV or an external stereo amplifier and speakers. (See pp. 12, 14.)

• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.

• Hi-Fi and normal audio playback volume level may differ.

• Arrow indicates

selection.

• Refer to “Receivable Broadcast Types”

on p. 26.

• Arrow indicates selection.

• Select “HIFI (L/R)” or “HIFI (L)” or

“HIFI (R)” to listen to stereo recordings

in stereo sound.

Select “NORMAL” for monaural sound.

• Display disappears after 5 seconds.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

(Display disappears after 5 seconds.)

Press AUDIO (SAP/Hi-Fi) repeatedly

to select desired mode.

Press AUDIO (SAP/Hi-Fi)

to display audio mode.

Press AUDIO (SAP/Hi-Fi) repeatedly

to select desired mode.

Notes

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1627

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Multi-Brand Control Feature

The Remote Control can be set to control some Televisions.

Find your TV Brand Code Number on the

following page.

Set up for TV control,

➛➛

➛ hold down TV button,

➛➛

➛ enter code with NUMBER keys.

Multi-Brand Control Setup

Confirm code entry,

➛ press POWER to turn selected unit on or off.

• See table below for controllable functions in each mode.

• Repeat setup after remote battery replacement.

• Remote will not control every TV made by the

manufacturer listed. If you get no response, your

particular unit cannot be controlled.

There are NO additional codes for the products listed.

If your product is not listed, then the remote is not

compatible with that product.

Notes

Mode

Unit

DVD/VCR TV

DVD

VCR

All

POWER, INPUT, NUMBER keys,

ENTER, CH / , VOL

EJECT/

OPEN/CLOSE

DISPLAY

PLAY

STOP

FF/SLOW+

REW/SLOW-

VCR/TV, PAUSE

/STILL

SKIP

AUDIO

CM/ZERO, SPEED, REC, TAPE

POSITION,

PAGE

, COUNTER RESET

After remote is set up, you can select VCR, DVD, or TV

for the desired function.

Press VCR,

DVD

, or TV on the remote.

(Table below shows available remote buttons for each mode.)

Using Multi-Brand Control

• Not all functions listed may be controllable.

• In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel

selection.

Notes

VOL

* Bold: VCR Function

Bold Italic: VCR and DVD Functions

Italic: DVD Function

Normal: TV

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1628

VCR Operation

• Some manufacturers use several codes for one brand.

If the first code entered fails, try the next one listed.

• Some Televisions require you to turn on the power manually.

Panasonic ............................................... 01, 02

Quasar.................................................... 01, 02

RCA ................................................................ 03

GE .................................................................. 03

Zenith ............................................................. 04

Magnavox ...................................................... 05

Sylvania ......................................................... 05

Sharp....................................................... 06, 07

Sony ............................................................... 08

TV Brand Code Numbers

Important Notes

VCR

POWER

ENTER

NUMBER

keys

DVD

Toshiba .......................................................... 09

Sanyo ............................................................. 10

Fisher............................................................. 10

JVC ................................................................ 11

Hitachi ............................................................ 12

Mitsubishi ................................................ 07, 13

Samsung ....................................................... 14

Gold Star .......................................... 15, 16, 17

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1629

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Commercial Skip

DECK fast forwards (skips) over 1, 2, or 3 minutes

of recorded tape as desired.

Press CM/ZERO in Play mode.

PLAY

1st Press

2nd Press

3rd Press

1 min Skip

2 min Skip

3 min Skip

• No indication appears on-screen.

• The skip time can be changed by pressing

CM/ZERO repeatedly as shown by the

figure below.

Index Search

Note

• If Index Search is started very close to an

index mark, that index mark may not be

counted in the search.

Tape Operation

Search System

For each recording, an invisible index

mark is placed on the tape. A program

index and information are also included

for timer recordings. These marks are

used to access or scan recordings.

Press SEARCH*

to display SEARCH

in Stop or Play

mode, and then

press NUMBER

keys to select

recording number.

• To calculate number,

see below.

Press FF/SLOW+ or

REW/SLOW- on the

remote to start

search.

Play begins at

search end.

To search forward

or back 1 index,

press FF/SLOW+ or

REW/SLOW- on the

remote while

screen left is

displayed (10 sec.).

• To cancel, press

PLAY or STOP.

To Calculate Index Number

Example 1:

To go to rec. 2 from rec. 4, enter 3 and press REW.

Example 2:

To go to rec. 6 from rec. 2, enter 4 and press FF.

NOTE: indicates start points of each recording.

61572 34

17534 62

Zero Search

To quickly return to a specified tape location.

Continue to record, playback etc.

Press STOP.

• DECK will go into FF or REW mode and

stop at the last point the Counter was set

to 0:00:00.

Press DISPLAY during play

to display Counter.

Press COUNTER

RESET on remote at

desired position to

reset to “0:00:00”.

Press CM/ZERO

in Stop mode to start

Zero Search.

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1630

VCR Operation

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

Repeat Play

Set to playback a recording over and over.

Press ACTION

to display MENU.

Press

to select “SET UP

VCR,” and press

SET.

• Playback repeats at tape end or if

unrecorded portion over 30 sec. is detected.

Press ACTION

to return to normal screen.

Press

to select “REPEAT

PLAY,” and press

SET to set “ON” or

“OFF.”

Note

• For repeat play in DVD mode, see page 47.

Auto Operation Functions

REW/

SLOW-

FF/

SLOW+

PLAY

STOP

NUMBER

keys

SET

SELECT

ACTION

DISPLAY

COUNTER

RESET

CM/ZERO

Auto Play

Insert a tape ➛ Power comes on,

➛ Play starts if there is no record tab

(see p. 6).

Auto Rewind

Play

Fast Forward

Play Auto Eject

(Repeat Play must be off)

Play

➛ ➛

➛ Tape end

➛ ➛

➛ Rewind

➛ ➛

➛ Stop

➛➛

➛ Tape ejects

(If there is no record tab or some timer

programs are set.)

➛

Tape end

➛

Rewind

➛➛

➛

Stop

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1631

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Tape Operation (continued)

DETECTING TAPE POSITION

To find out the present tape position and amount of tape

remaining.

•“DETECTING TAPE POSITION”

only appears the first time a

cassette is inserted and it takes

several seconds for correct

indication to appear.

• The present tape position

indication and amount of tape

remaining (according to tape

speed) are displayed.

Tape remaining time display may

not be precise.

Tape Position Display

Press TAPE POSITION

to detect current tape position.

Tape position is displayed incorrectly in the following cases:

• If VHS-C type cassettes, tapes under 30 minutes, tapes

over 180 minutes, or incompatible tapes are used.

• If the correct tape length is not selected.

(See “Tape Select” section above.)

Tape Select

Select your tape length so the tape position and amount

of tape remaining are properly displayed.

(See “Tape Position Display” section below.)

Press ACTION

to display MENU.

Press

to select

“SET UP VCR,” and

press SET.

Press ACTION

to return to normal screen.

Press to select “TAPE

SELECT,” and press SET

to set

“T-120,” “T-160” or “T-180.”

• Select “T-120” for tapes 120 minutes or less,

“T-160” if 140 or 160 minutes, and “T-180”

if 180 minutes.

T-120 T-160 T-180

Press TAPE POSITION

(or wait 5 seconds) to return to normal screen.

*Important:If a remote control button does

not work when pressed, press

the VCR button on the remote

and try the button again.

ACTION

SET

SELECT

TAPE

POSITION

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1632

VCR Operation

Weak Signal Display Feature

When “ON,” picture is displayed regardless of signal

strength.

• ON: Picture is displayed regardless of signal

condition, and may not always be clearly visible.

OFF: Screen turns solid blue when signal is weak or

non-existent.

• Selecting ON has no effect on connected equipment

with blue back feature.

Press ACTION

to return to normal screen.

Press

to select “SET UP

CHANNEL,” and

press SET.

Press

to select “WEAK SIGNAL

DISPLAY,” and

press SET

to set “ON” or “OFF.”

Press ACTION

to display MENU.

Auto Shut-Off Feature

The power shuts off at a preset time.

Press

to select “AUTO SHUT-OFF.”

Press SET repeatedly to

change shut-off time as

shown below.

Press ACTION

to return to normal screen.

Press ACTION

to display MENU.

Press

to select “SET UP VCR,” and

press SET.

OFF

2 Hours

6 Hours

4 Hours

• The shut-off countdown will not function during Play or

Record.

Note

ACTION

SET

SELECT

Special VCR Features

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1633

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Special VCR Features (continued)

*Important:If a remote control button does

not work when pressed, press

the VCR button on the remote

and try the button again.

VCR/TV Selector FeatureVCR/TV Selection Feature

The VCR/TV selection can be set to auto or manual.

Press ACTION*

to display MENU.

Press

to select “AUTO VCR/TV,”

and

press SET

to set “ON” or “OFF.”

Press ACTION

to return to normal screen.

Note

• OFF(Manual): You select “VCR” or “TV” mode using

the VCR/TV button on the remote.

• ON(Auto): “VCR” mode is automatically set when

VCR is turned on, or in Play mode.

• For more on VCR/TV selection, see “Record one

station, watch another” and “Select channels at DECK”

sections (see p. 21).

Press

to select “SET UP VCR,”

and

press SET.

ACTION

SET

SELECT

INPUT

STOP

REC

STILL/

PAUSE

VCR

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1634

VCR Operation

Copying Your Tapes (Dubbing)

Insert a pre-recorded tape.

Insert a blank tape with record tab.

Press REC, then STILL/PAUSE

immediately to enter REC/PAUSE mode.

Press INPUT to set DECK Input mode to

LINE for Video Input.

(See “Selecting the Input Mode” below.)

Press PLAY to start dubbing.

Playing VCR starts playback.

Press STILL/PAUSE to start dubbing.

DECK starts recording.

Press STOP to stop dubbing.

Caution: • Unauthorized exchanging and/or copying of copyrighted recordings may be

• Please note that some tapes cannot be dubbed on DECK.

Also, it is not possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.

• When appears on the screen while a button is being operated, it means that

the corresponding operation is prohibited by DECK or the disc.

Playing (Source) VCR

Recording (Editing) DECK

To Monitor Dubbing on TV

1 Turn TV on and tune to the Recording VCR

channel (CH 3 or CH 4).

2 If Auto VCR/TV (see p. 34) is set to “OFF,”

press VCR/TV on the remote for VCR

mode.

• Dubbing tapes protected with Copy

Guard will result in poor quality

recordings.

Connection

Press STOP to stop dubbing.

Press PLAY, then PAUSE immediately

to enter PLAY/PAUSE mode.

Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.

To monitor the dubbing, also connect TV as shown.

Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN

terminals on DECK.

In place of Playing VCR, you can use other equipment, such as a Camcorder.

Simply connect the unit’s Audio/Video outputs to DECK.

Selecting the Input Mode

Method 1: Press INPUT repeatedly.

Channel Number

➛➛

➛ LINE1

➛➛

➛ LINE2

Method 2: Press CH / .

Display will change as below.

Front of DECK

VIDEO IN 2

L-AUDIO IN2-R

(Audio/Video In Terminals

on the front of DECK are

available)

FROM

ANT.

OUT

IN 1

VHF/UHF

OUT

VHF/

UHF

DVD/VCR DECK

VIDEO

AUDIO

VCR/ Camcorder (Hi-Fi)

VIDEO

AUDIO

• LINE1: For rear audio/video connection.

LINE2: For front audio/video connection.

125

LINE1

(CABLE)

(TV)

LINE2

Press

The operation of steps 4 and 5 must be done on the

playing and recording VCRs at the same time.

Note

PV-D4735S P26-35 (041224).p65 2004/12/24, 13:1635

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Disc Operation

Ready Checklist

Please read “Basic DVD Operation”

on page 22.

[Subtitle language]

[Audio sound track language]

• Change the No. by pressing ,

and press

SET

[Audio attribute 1 type, sampling

frequency, bit No. of the disc (see p. 53.)]

• If, after several presses of the AUDIO

button the language does not change,

language selection is not offered on

the disc.

• When disc is removed, language

reverts to initial setting. If this language

is not recorded on the disc, the

language recorded will be heard.

• With DVD-RAM, Audio Soundtrack

Language cannot be set. Audio stream

and Audio mode (LR/L/R) setting can

be made. Audio stream operation

method is the same as Audio

Soundtrack Language. Press to

move the cursor to Audio mode, then

press AUDIO or to select LR/ L/ R.

Notes

You can select a different subtitle language (if offered) than

the one set at the Settings for DVD Operation. (See p. 52.)

Subtitle Language (DVD only)

• Display disappears after

5 seconds.

Press

SUB TITLE

in Play mode to display

the subtitle selection

on-screen.

Notes

• If after several presses of the button the language does

not change, language selection is not offered on the disc.

• When disc is removed, subtitles revert to initial setting

language. If the initial language is not recorded on the

disc, the disc’s priority language will appear.

• With DVD-RAM, the subtitle can only be set to ON/OFF.

The subtitle language cannot be selected.

• Subtitles may not change to the selected language

immediately.

You can change the audio soundtrack language, selected

at the Settings for DVD Operation, to a different language

if available. (See p. 52.)

(This operation works only with discs on which multiple

audio soundtrack languages are recorded.)

Press

AUDIO

in Play mode to display the

audio selection on-screen.

Audio Soundtrack Language (DVD only)

Information of the audio stream

currently being played back is

displayed. (See page 53.)

• Display disappears after

5 seconds.

Audio soundtrack language

being played back (see chart,

above right).

LPCM

Dolby Digital

DTS

96 kHz

48 kHz

1c h - 5.1 ch

1 ch - 5.1 ch

16 bit

20 bit

24 bit

Linear PCM disc

Dolby Digital disc

DTS disc

ENG

FRA

DEU

ITA

ESP

NLD

SVE

NOR

DAN

POR

RUS

JPN

CHI

KOR

MAL

VIE

THA

∗

English

French

German

Italian

Spanish

Dutch

Swedish

Norwegian

Danish

Portuguese

Russian

Japanese

Chinese

Korean

Malay

Vietnamese

Thai

Other

Press

SUB TITLE

repeatedly, , or

NUMBER keys

to select

desired language.

Subtitle language being played

back (see chart, right).

Press

AUDIO

repeatedly,

, or

NUMBER keys

select desired language.

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1636

When appears on the screen while

a button is being operated, it means

that the corresponding operation is

prohibited by DECK or the disc.

Press

AUDIO

in Play mode

to display the audio screen.

Vocal Selection for Karaoke Discs (DVD/Video CD)

DVDs may contain scenes shot from multiple camera

angles allowing the same scene to be viewed at different

angles. You can view these angles, if available, using the

ANGLE button.

Press

ANGLE

in Play mode to display the

angle selection on-screen.

• Display disappears after

5 seconds.

Multiple Angle Viewing (DVD only)

Press to select VOCAL

and

press

AUDIO

or to

select as shown below.

Number of angle being played back.

You can enlarge specific portions of a picture and select

the zoom ratio using the ZOOM button during DVD

playback.

Press

ZOOM

repeatedly to change display

as follows.

Picture Zoom (DVD only)

• You can enlarge the center portion of the image to one of

2 magnifications.

■ Use the , , and buttons to move the position

up, down, left and right.

Notes

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

This function not available with DVD-RAM.

Note

• The subtitle cannot be enlarged or

moved.

• The picture zoom feature does not

work with a Video CD.

• During picture zoom, “ZOOM1” or

“ZOOM2” appears on-screen for 5

seconds.

• Zooming, on some discs, may result

in poor picture quality, or may not

operate at all.

DVD Operation

SET

SELECT

AUDIO

ANGLE

SUB TITLE

ZOOM

NUMBER

keys

• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF

• DVD Karaoke (2 vocals) VOCAL V1 VOCAL V2 VOCAL V1+V2 VOCAL OFF

• Video CD LR L R

Press

ANGLE

repeatedly,

, or

NUMBER keys

select desired language.

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1637

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

You can program specific tracks and order of play.

Program Play (Video CD/CD only)

Ready Checklist

DECK is in DVD mode, press DVD.

Video CD or CD is inserted.

Press

ACTION

to display DVD MAIN MENU.

Press

to select

“PLAY MODE,” and

press

SET

to display.

Press

to select

“PROGRAM PLAY,”

and

press

SET

to display.

Press

to select “START,” and

press

SET

to start play of programs in

the sequence selected.

• To cancel, press

STOP

during play, then press

CLEAR

Press

to select a track number

(Track numbers on disc

are displayed.), and

press

SET

• Repeat step 4 to select another track.

• The selected track is added on the right side.

Disc Operation (continued)

CLEAR

ACTION

SET

SELECT

STOP

DISPLAY

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1638

Notes

Program Repeat Play

(Video CD/CD only)

Press

SET

to enter Select mode.

Press to select “DISC.”

(DECK Information Screen)

Do operation steps 1 through 5

on the previous page.

Press

DISPLAY

to display Disc Information

screen.

(Disc Information Screen)

Press

DISPLAY

to display DECK Information

screen.

Press

SET

to set mode.

Cursor moves to “REPEAT.”

To cancel, select “REPEAT : OFF”

in step 5, then press

SET

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

• Up to 16 tracks can be programmed.

•“ ” or “ ” (depending on disc)

indicates additional PROGRAM PLAY

screen. Press for next or

previous screen.

• To clear the last program one by

one

Press to move to “CLEAR

LAST” and press

SET

. (Pressing

CLEAR

on remote control also clears

last program.)

• To clear all programs

Press to move to “CLEAR ALL”

and press

SET.

(Programs are also

cleared when the power is turned off or

the disc is removed.)

DVD Operation

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1639

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Tracks are played in a random order.

Random Play (Video CD/CD only)

Press

ACTION

to display DVD MAIN MENU.

Disc Operation (continued)

Press

to select “PLAY MODE,”

and

press

SET

to display.

Press

to select

“RANDOM PLAY,” and

press

SET

to begin random play.

• To cancel, press

STOP

during play, then press

CLEAR

Ready Checklist

DECK is in DVD mode, press DVD.

STOP

PLAY

NUMBER

keys

TITLE

CLEAR

ACTION

SET

SELECT

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1640

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

DVD Operation

Some DVDs have more than one title, e.g. movies.

If the disc offers a title menu, you can select the desired

title number. (Operation may vary according to the disc.)

Press

TITLE

in Play mode

to display the title screen.

Title Menu (DVD only)

DVDs may offer a special menu. This menu may include

guides to unique contents, audio/subtitle languages, etc.

Although contents and operation may vary, the following

steps show basic procedure for using the menu.

Press

in Play mode to display

DVD MENU.

Press

NUMBER keys

to select an item, and

press

SET

PLAY

to perform.

DVD Menu (DVD only)

Press or

NUMBER keys

to select a title, and

press

SET

PLAY

to start playing.

•“Pressing

SET

PLAY

” is

not necessary when using

NUMBER keys.

Repeat step 2 if there is

more than one menu.

• Pressing

SET

PLAY

not necessary when using

NUMBER keys.

Cats

Samurai

Friend

Music

TITLE MENU

Music

Cats

Samurai

Friend

TITLE MENU

Music

of the world

1 SUBTITLE

2 AUDIO

3 ANGLE

DVD MENU

1 SUBTITLE

2 AUDIO

3 ANGLE

DVD MENU

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1641

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

DVD-RAM Operation (DVD-RAM only)

• This DECK was designed for playback only. DVD-RAM recording is not possible.

You can enjoy playing your personally recorded/edited DVD-RAM discs on this DECK.

Note

Press

D.NAVI

in Play/Stop mode to display the Direct Navigator

menu.

Press to select a page and press

select a title (Program No.).

Then, press

SET

PLAY

to start playing.

If the DVD-RAM features Direct Navigator, a list of recorded titles is displayed. Simply select a title

number and start playback. (Operation can vary with disc used.)

Direct Navigator

•“Pressing SET or PLAY” is not necessary when

using NUMBER keys.

Program No.

Titles

Recording

time length

Recording time

and date

Page No.

<Input

Example>

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

1 digit number 1 ••• 1

2 digit number 12 ••• 10 ➛ 1 ➛ 2

Press

D.NAVI

to clear Direct navigator menu.

(Example)

Do steps 1 ~ 3 on page 22.

Press

D.NAVI*

PLAY LIST

to display Direct

Navigator or Play List menu for easy title or

scene selection.

Press

STOP

to stop playing.

Press

OPEN/CLOSE

to eject the disc.

Play a DVD-RAM

• Play begins from the first program title recorded on

the DVD-RAM.

• See below for “Direct Navigator” or next page for

“Play List information”.

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1642

Press

PLAY LIST

in Play/Stop mode to display the Play List menu.

Press to select a page and press

select a title (Play List No.).

Then, press

SET

PLAY

to start playing.

If the DVD-RAM features a Play List, your preselected list of favorite scenes is displayed for easy

access. (Operation can vary according to how you edited the DVD-RAM.)

Play List

•“Pressing SET or PLAY” is not necessary when

using NUMBER keys.

TitlesRecording time

and date

Page No.

<Input

Example>

Using NUMBER keys starts playing automatically.

The number of available titles varies with each disc.

1 digit number 1 ••• 1

2 digit number 12 ••• 10 ➛ 1 ➛ 2

Press

PLAY LIST

to clear Play List menu.

Play List No.

Established

time length

(Example)

• Titles of Direct Navigator and Play List cannot be changed using this DECK.

• With Direct Navigator, up to 99 programs can be displayed. With Play List, up to 99 titles (999

scenes) can be displayed.

• While DVD MAIN MENU is displayed, Direct Navigator and Play List display will not appear even

if TITLE or MENU is pressed.

• When appears on the screen while a button is being operated, it means that the

corresponding operation is prohibited by DECK or the disc.

Notes

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

DVD Operation

NUMBER

keys

PLAY LIST

SET

SELECT

D.NAVI

STOP

PLAY

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1643

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

DVD Operation using On-Screen Displays

Press

DISPLAY*

in Play or Stop mode

to display “On-Screen Displays.”

When

DISPLAY

is pressed, On-Screen Displays show disc

information (title/chapter/track number, elapsed playing

time) and DECK information (repeat play, play mode).

• Each press of

DISPLAY

changes the on-screen

display as follows. (Refer to pp. 44 ~ 48.)

Note

Press or

NUMBER keys

to select the setting, and press

SET

Press

to select an item, and

press

SET

• When numbers are

displayed (e.g. title

number),

NUMBER

keys

are also available.

• If the number entered is

not on the disc, the

entry will have no

effect. Re-enter the

correct number.

• For more details, refer

to the disc operation

information.

To return to normal

screen,

press

DISPLAY

repeatedly.

Ready Checklist

DECK is in DVD mode, press DVD.

Selected Disc information

Selected DECK information

Normal Screen

➡

(See pp. 45, 46.)

(See pp. 47, 48.)

•

DISPLAY

button does not function while main menu of

DVD, title menu of DVD, Direct Navigator or Play List

is displayed.

NUMBER

keys

SET

SELECT

DISPLAY

• When

DISPLAY

button is pressed

during playback of a Video CD with

Playback control,

NUMBER keys

are

not available on the displayed screen.

In this case, press

DISPLAY

again to

remove the displayed screen.

• When appears on the screen while

a button is being operated, it means

that the corresponding operation is

prohibited by DECK or the disc.

Notes

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1644

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

Detailed Descriptions of each On-Screen Display

■■

■ Disc information screen (for DVD-Video)

1. TITLE No.

Go directly to a preset title number.

• Select “TITLE”, and press

SET

• Change the No. by pressing

NUMBER keys

, and press

SET

2. CHAPTER No.

Go directly to a preset chapter number.

• Select “CHAPTER”, and press

SET

• Change the No. by pressing or

NUMBER keys

, and press

SET

• This function does not work with some discs.

3. Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press

SET

• Change the elapsed time by pressing

NUMBER keys

Enter time starting with seconds.

If the time entered is not on the disc, the entry will have no effect.

Re-enter the correct time.

e.g., press 0 ➛ 1 ➛ 2 ➛ 3 ➛ 4 ➛ 5 ➛ SET for “01 : 23 : 45”.

press 3 ➛ 0 ➛ SET for “00 : 00 : 30”.

• This function does not work with some discs.

4. Disc currently being played

The type of disc currently inserted is displayed.

5. Operating mode

The current operation is displayed.

■■

■ Disc information screen (for Video CD/ CD)

A.TRACK No.

Go directly to a preset track number.

• Select “TRACK”, and press

SET

• Change the No. by pressing or

NUMBER keys

, and press

SET

B.Elapsed playing time

When disc information screen is displayed, it is not possible

to enter an elapsed playing time.

C.Disc currently being played

The type of disc currently inserted is displayed.

D.Operating mode

The current operation is displayed.

E. Playback control ON/OFF

F. Play mode (See p. 38, 40.)

When Play mode is set (p. 38, 40), the mode name is displayed.

Note

DVD Operation

• Track No. and the elapsed playing time are not displayed during play started from

menu of Video CDs with playback control.

<CD>

PBC ON Video CD menu play is displayed.

PBC OFF Video CD menu play is not displayed.

PROGRAM PLAY program play

RANDOM PLAY random play

---- normal play

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1645

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

■■

■ Disc information screen (for DVD-RAM)

1. Direct Navigation (PROGRAM) or PLAY LIST No.

Go directly to a preset title number.

• Select “PROGRAM” or “PLAY LIST”, and press

SET

• Change the No. by pressing or

NUMBER keys

, and press

SET

2. Elapsed playing time

The screen may be changed by selecting the elapsed time.

• Select the elapsed playing time (“xx:xx:xx”), and press

SET

• Change the elapsed time by pressing

NUMBER keys

Enter time starting with seconds.

If the time entered is not on the disc, the entry will have no effect.

Re-enter the correct time.

e.g., press 0 ➛ 1 ➛ 2 ➛ 3 ➛ 4 ➛ 5 ➛ SET for “01 : 23 : 45”.

press 3 ➛ 0 ➛ SET for “00 : 00 : 30”.

• This function does not work with some discs.

3. Disc currently being played

The type of disc currently inserted is displayed.

4. Operating mode

The current operation is displayed.

Direct Navigation

(PROGRAM)

PLAY LIST

DVD Operation using On-Screen Displays (continued)

• When appears on the screen while a button is being operated, it means that the

corresponding operation is prohibited by DECK or the disc.

Note

NUMBER

keys

SET

SELECT

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1646

. Repeat Play mode (see p. 48)

Repeat play mode can be selected.

• Select “REPEAT”, and press

SET

• Change the desired mode during play by pressing , and press

SET

. SURROUND (see p. 23)

■■

■ DECK information screen (for DECK)

• For repeat play in VCR mode, see p. 31.

Note

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

DVD Operation

SET

SELECT

Repeat Play mode

DVD-Video CHAPTER TITLE OFF (NORMAL)

DVD-RAM (PROGRAM) PROGRAM DISC OFF (NORMAL)

(PLAY LIST) PLAY LIST ALL PLAY LISTS OFF (NORMAL)

Video CD/CD TRACK DISC OFF (NORMAL)

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1647

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

TITLE

chapter

CHAPTER REPEAT

TITLE REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

PROGRAM

PROGRAM REPEAT

DISC REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

PROGRAM

PLAY LIST

PLAY LIST REPEAT

ALL PLAY LIST REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

PLAY LIST

DVD Operation using On-Screen Displays (continued)

• CHAPTER/TITLE REPEAT PLAY (DVD-Video)

For your reference

Important: if a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

• PROGRAM/DISC REPEAT PLAY (DVD-RAM [PROGRAM])

• PLAY LIST/ALL PLAY LIST REPEAT PLAY (DVD-RAM [PLAY LIST])

OPEN/

POWER

PAUSE

STOP

PLAY

NUMBER

keys

ACTION

SET

SELECT

REW

track

TRACK REPEAT

DISC REPEAT

NORMAL PLAY

CURRENT PLAYBACK POSITION

• TRACK/DISC REPEAT PLAY (Video CD/CD)

Repeat Play mode example (see p. 47)

• For repeat play in VCR mode, see p. 31.

Note

SKIP+

SKIP

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1648

MP3/JPEG Playback Operation

• Only File (not Folder) area

operation is possible.

• Files are displayed in the

following order:

(!...0,1....9,A,B......Z).

Notes

• Select file (During STOP mode)

1)Press to select an MP3 file (

➡ MP3 Playback (see right)

2)Press to select a JPEG file ( ).

➡ JPEG Playback (see p. 50)

3)Press

SKIP+

| (next) or

SKIP-

(previous) to skip a file/folder page (7 files)

in the File area.

• Select folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

SET

to display files/folders

contained in the folder.

• Select parent folder (During STOP mode)

1)Press to select a folder ( ).

2)Press

SET

to make changes to the

previous directory display.

Press

ACTION

to return the DVD MAIN

MENU. (➛ Press

ACTION

again to

return to the MP3/JPEG MENU.)

MP3 Playback

■ Forward/Reverse Search

Press

FF/SLOW+

REW/SLOW-

during play.

Press

PLAY

to release.

• Search speed, slow at first, increases with

each additional press of the button up to 5

levels.

■ Forward/Reverse Track Skip

Press

SKIP+

| or

SKIP-

| during play.

Each press skips a track.

• If pressed within first 3 seconds of playback,

skips to the previous track. If over 3 seconds,

returns to top of track. (

SKIP-

| only.)

• Put DECK in Stop mode before performing

folder/file selection (see step 4.)

■ Pause

Press

PAUSE

during play.

Press

PLAY

to release.

Press to select an MP3 file (

(During STOP mode)

Press

SET

PLAY

to start playback.

Press

STOP

to stop play.

Do steps 1~3 at left.

[PLAY MODE]

NORMAL:

All MP3 files are selected and played back

one time only.

SINGLE REPEAT:

The selected MP3 file is played back

repeatedly.

FOLDER REPEAT:

The MP3 files contained in the selected folder

are played back repeatedly.

However, folders below the selected folder

are not played back.

DISC REPEAT:

All MP3 files are played back repeatedly.

■ Select PLAY MODE [MP3 Playback]

(During STOP mode)

Press to select the desired PLAY MODE

(see below).

Function

Status

PLAY MODE

Folder area

File area

Parent

folder

(Current folder

appears green.)

(Selected file/

folder is

highlighted.

Titles are

displayed

up to 11

characters.)

(Diagram left shows CD directory

structure as displayed in example

OSD above.)

:MP3 file :JPEG file

:Folder :Parent folder

Press

POWER

* on the remote or DECK.

Press

OPEN/CLOSE

then place an MP3/JPEG disc into the

disc tray.

Press

OPEN/CLOSE

to close.

This unit can play MP3/JPEG format CD-R or

CD-RW recorded for personal use on a PC, etc.

Some discs may not play due to the condition of

the recording.

• MP3/JPEG MENU is displayed.

• Playback starts automatically

(except JPEG files).

• CD directory is displayed.

Press

OPEN/CLOSE

to eject the disc.

The MP3/JPEG MENU is closed

automatically.

• Copyright protected files and files containing

errors cannot be played back. The DECK

skips to the next file.

Note

ROOT

TECHNO

POPS

AZZ

END

ALTZ

DD_CUB I C

CTURNE

DVD Operation

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1649

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

MP3/JPEG Playback Operation (continued)

JPEG Playback

Press to select a JPEG file ( ).

■ Returned on the MP3/JPEG MENU

➡ Press

STOP

. (See p. 49)

■ Next/Previous Search

➡ Press

SKIP+

| or

SKIP-

| .

■ Start Slide-show ➡ Press

FF/SLOW+

REW/SLOW-

. (below)

■ Enlarging an image ➡ Press

ZOOM

. (P. 51)

■ Rotating an image ➡ Press

ANGLE

. (P. 51)

[JPEG Playback Screen]

Do steps 1~3 on page 49.

Press

SET

PLAY

Selected JPEG file is displayed.

You can play back JPEG images.

Displayable Image Size: 32x32~7680x7680 pixels

Image changes every 3 seconds.

JPEG Slide-show

Press

FF/SLOW+

REW/SLOW-

JPEG files are displayed automatically

(about every 3 seconds) as a slide-show.

Press

ACTION

to return to

the DVD MAIN MENU.

(During JPEG Playback.)

■ Cancel slide show

➡ Press

STOP

to return the MP3/JPEG

MENU. (See p. 49)

■ Still picture

➡ Press

STILL

(only SLIDE).

➡ Press

PLAY

to release.

■ Forward/Reverse File Skip

➡ Press

SKIP+

| or

SKIP-

| .

Each press skips a file.

Operation can be done when files are in order,

such as in the diagram below.

• Some JPEG format may not be played

back.

Note

Press

STOP

to return to the MP3/JPEG

MENU.

[PLAY MODE]

NORMAL:

All JPEG files are selected and played back

one time only.

SINGLE REPEAT:

The selected JPEG file is played back

repeatedly.

FOLDER REPEAT:

The JPEG files contained in the selected

folder are played back repeatedly.

However, folders below the selected folder

are not played back.

DISC REPEAT:

All JPEG files are played back repeatedly.

■ Select PLAY MODE [JPEG Slide-show]

(During STOP mode)

Press to select the desired PLAY MODE

(See below).

REW/SLOW-

FF/SLOW+

REW/SLOW-

FF/SLOW+

ROOT

AAA

DDD

TTT

UUU

VVV

WWW

ZZZ

01 PIC

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1650

You can enlarge specific portions of a JPEG picture

and select the zoom ratio using the ZOOM button

on the remote during JPEG Playback screen.

Set Zoom size.

Press

ZOOM

repeatedly to change display

as follows.

➡

Press

STOP

to return the MP3/JPEG MENU.

• You can enlarge the center portion of the image

to one of 2 magnifications.

• Operation can be done during Rotation (below).

X 1.0 (ORIGINAL)

1st press

2nd press

3rd press

X 1.5 (ZOOM 1) X 2.0 (ZOOM 2)

■ Use the , , and buttons to move the

position up, down, left and right.

(Position cannot be changed on X1.0

ORIGINAL images.)

JPEG Zoom

JPEG Rotation

(During JPEG Playback.)

Set rotation.

Press

ANGLE

repeatedly to change display

as below.

➡

Press

STOP

to return the MP3/JPEG MENU.

(During JPEG Playback.)

You can rotate a JPEG picture using the ANGLE

button on the remote during JPEG Playback

screen. (The JPEG picture will be rotated 90°

clockwise.)

2nd press 3rd press

• Operation can be done during Zoom (above).

• The vertical/horizontal ratio of rotated JPEG

images may vary when they are displayed.

1st press

4th press

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and

Thomson multimedia.

REW/

SLOW-

FF/

SLOW+

PLAY

STILL

STOP

SET

SELECT

ACTION

ZOOM

ANGLE

SKIP+

SKIP

DVD Operation

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1651

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

“AUDIO” selections

(Factory preset: English)

To select the audio soundtrack language.

English/Spanish/French/Japanese

Original: Original disc language

OTHER 0000: Other language selection*

“SUBTITLE” selections

(Factory preset: AUTO)

To select the subtitle language.

AUTO:Same language selected for “AUDIO”

• If language set for “AUDIO” is used in

playback, subtitles will not appear.

• If another language is used during

playback, the subtitles will appear in the

language selected at “AUDIO” setup.

English/Spanish/French/Japanese

OTHER 0000: Other language selection*

“MENUS” selections

(factory preset: English)

To select the language used in title menus or

DVD menus.

English/Spanish/French/Japanese

OTHER

0000

Other language selection*

To enter OTHER ✱✱✱✱

code number,

Press

NUMBER keys

(Please refer to

language codes on p. 56).

To make corrections, press repeatedly to

delete language code number, and correct.

Settings for DVD Operation

Once initial settings are done, they remain in

memory (even after power is turned off) until

changed. This means DECK will operate

under the same conditions (especially DVDs)

each time.

If the selected language is not offered,

the original disc language is selected.

Ready Checklist

DECK is in DVD mode, press DVD.

Press

ACTION

to display DVD MAIN MENU.

Press

to select an item, and

press

SET

DISC LANGUAGES (See below)

All languages offered on the disc can be set.

If a language not offered is set, the original disc

language will be selected.

AUDIO OUTPUT (See p. 53.)

You can set the audio output that comes from the

digital audio output terminal.

STILL MODE (See p. 54.)

To select “FIELD” (Field still) or “FRAME” (Frame

still) to prevent jitter or make small text or fine

patterns clearly visible in a still picture.

When “AUTO” is set, “FIELD” or “FRAME” is

selected automatically.

TV MODE (See p. 54.)

To select whether the video material for a wide-

screen will be played back in the Pan & Scan style,

Letterbox style or 16 : 9 style.

Disc Languages (DVD only)

To select and set the language of the audio

soundtrack, subtitles, or title/DVD menus for all

discs to be played.

Press

to select

“DISC LANGUAGES,”

and

press

SET

to display screen.

Press

to select an item, and

press

SET

repeatedly

for desired language.

(Please refer right.)

Press

ACTION

to redisplay DVD MAIN

MENU and go to step 2 to setup another

item.

Or, press

ACTION

twice to exit.

ACTION

NUMBER

keys

SET

SELECT

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1652

Audio Output (DVD only)

Select the digital output to be output from the optical

digital audio output connector of DECK.

■■

■ “LPCM (DVD)” selections

OFF: Linear PCM of less than 48 kHz/16 bit is

output. When playing DVDs recorded in linear

PCM of over 48 kHz/20 bit, no digital audio is

output. (Factory preset)

PCM: When playing DVDs recorded in linear PCM

of 48 kHz/20 bit/24 bit or more, digital audio

converted to 48 kHz/16 bit is output.

(Digital output of PCM audio is restricted to

48 kHz/16 bit or below for copyright

protection.)

■■

■ “Dolby Digital” selections

Bitstream: Dolby Digital bitstream (1 ch - 5.1 ch)

is output. (Factory preset)

PCM: When you have connected an amplifier that

doesn’t have a built-in Dolby Digital decoder.

■■

■ “dts” selections

Bitstream: DTS bitstream is output. (Factory preset)

PCM: When you have connected an amplifier that

doesn’t have a built-in DTS decoder.

■■

■ “DRC (Dynamic Range Compression)”

selections

OFF: Normal audio range is selected. (Factory preset)

ON: For dynamic sound even at low volume,

this is useful for late-night listening.

[Dolby Digital DVDs only].

Press

to select an item,

and

press

SET

repeatedly for

output. (See below.)

Press

to select

“AUDIO OUTPUT,”

and

press

SET

to display screen.

Recommended setting

LPCM

(DVD)

PCM

Dolby

Digital

PCM*

Bitstream

DTS

PCM*

PCM

Bitstream

No amplifier is

connected

AV amplifier (with

digital audio input

connector) without

Dolby Digital/DTS

decoder

AV amplifier

including Dolby

Digital decoder

AV amplifier

including Dolby

Digital/DTS

decoder

Type of amplifier

to be connected

Press

ACTION

to display DVD MAIN MENU.

Ready Checklist

DECK is in DVD mode, press DVD.

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

• Make settings according to amplifier

connected to optical audio output as shown

in above table.

*1 When connecting an amplifier (with an

optical digital input connector) which does

not contain the Dolby Digital or DTS

decoder, be sure to select “PCM”.

If “Bitstream” is selected, starting DVD

play may cause such a high level of noise

as to be harmful to your ears and damage

the speakers.

*2 When a dts decoder is connected, please

select “Bitstream” in “dts.”

If “PCM” is selected, there will be stereo

sound.

When a Dolby Digital decoder is

connected, please select “Bitstream” in

“Dolby Digital.”

If “PCM” is selected, there will be stereo

sound.

Press

ACTION

to redisplay DVD MAIN

MENU and go to step 2 to setup another

item.

Or, press

ACTION

twice to exit.

DVD Operation

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1653

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Still Mode (DVD only)

Press

to select “STILL MODE,”

and

press

SET

repeatedly

for mode. (See below.)

AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is

automatically selected during the still mode.

(Factory preset)

FIELD: “FIELD” (Field still) is always selected.

This setting will reduce jitter when compared

with “AUTO” on some discs.

FRAME:“FRAME” (Frame still) is always selected.

Some texts and fine patterns will be seen clearly

when compared with “AUTO” on some discs.

TV Mode (DVD only)

Press

to select “TV MODE,”

and press

SET

repeatedly for mode.

(See below.)

4:3 Pan & Scan (Factory preset) :

Wide-screen video data is played in Pan & Scan

style (left and right of screen is trimmed.)

• Video data not formatted in Pan & Scan will play

in letterbox style.

4:3 Letterbox :

Wide-screen video data is played in Letterbox

style (top and bottom of screen has black margin).

16:9 : Set “16:9” when using Wide-screen TV.

Set the screen display style for wide-screen video

material playback.

Set to reduce jitter in a displayed still picture or a motion

picture.

Press

ACTION

to exit this mode.

Press

ACTION

to exit this mode.

Press

ACTION

to display DVD MAIN MENU.

Press

ACTION

to display DVD MAIN MENU.

• Pan & Scan (Factory preset)

• Letterbox

Example

Settings for DVD Operation (continued)

SET

ACTION

SELECT

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1654

*Important: If a remote control button does not work when pressed,

press the DVD button on the remote and try the button again.

PROGRESSIVE OUT

Press to select

“PROGRESSIVE OUT,”

and

press

SET

repeatedly

for mode. (See below.)

OFF: Progressive scan signal is not output.

ON: Progressive scan signal is output from the

Component Video Output Connector.

Sets the Component Video Output Connector (p. 10, 13)

to output the Progressive scan signal.

Press

ACTION

to exit this mode.

Press

ACTION

to display DVD MAIN MENU.

• If the television is not progressive compatible, a

progressive scan picture is not available. Connect the

Video Output or S-Video Output connector (see p. 12,

13) and set PROGRESSIVE OUT to “OFF”.

• CONSUMERS SHOULD NOTE THAT NOT ALL HIGH

DEFINITION TELEVISION SETS ARE FULLY

COMPATIBLE WITH THIS PRODUCT AND MAY

CAUSE ARTIFACTS TO BE DISPLAYED IN THE

PICTURE.

IN CASE OF 525 PROGRESSIVE SCAN PICTURE

PROBLEMS, IT IS RECOMMENDED TO SET

PROGRESSIVE OUT TO “OFF”.

IF THERE ARE QUESTIONS REGARDING OUR TV

SET COMPATIBILITY WITH THIS MODEL 525p DVD/

VCR DECK, PLEASE CONTACT OUR CUSTOMER

SERVICE CENTER.

Notes

DVD Operation

SET

ACTION

SELECT

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1655

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Language Code List

Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or

“MENUS” (see p. 52).

Code Language

8375 Slovak

8376 Slovenian

8377 Samoan

8378 Shona

8379 Somali

8381 Albanian

8382 Serbian

8385 Sundanese

8386 Swedish

8387 Swahili

8465 Tamil

8469 Telugu

8471 Tajik

8472 Thai

8473 Tigrinya

8475 Turkmen

8476 Tagalog

8479 Tonga

8482 Turkish

8484 Tatar

8487 Twi

8575 Ukrainian

8582 Urdu

8590 Uzbek

8673 Vietnamese

8679 Volapük

8779 Wolof

8872 Xhosa

8979 Yoruba

9072 Chinese

9085 Zulu

Code Language

7678 Lingala

7679 Laothian

7684 Lithuanian

7686 Latvian, Lettish

7771 Malagasy

7773 Maori

7775 Macedonian

7776 Malayalam

7778 Mongolian

7779 Moldavian

7782 Marathi

7783 Malay

7784 Maltese

7789 Burmese

7865 Nauru

7869 Nepali

7876 Dutch

7879 Norwegian

7982 Oriya

8065 Panjabi

8076 Polish

8083 Pashto, Pushto

8084 Portuguese

8185 Quechua

8277

Rhaeto-Romance

8279 Romanian

8285 Russian

8365 Sanskrit

8368 Sindhi

8372

Serbo-Croatian

8373 Singhalese

Code Language

7079 Faroese

7082 French

7089 Frisian

7165 Irish

7168 Scots Gaelic

7176 Galician

7178 Guarani

7185 Gujarati

7265 Hausa

7273 Hindi

7282 Croatian

7285 Hungarian

7289 Armenian

7365 Interlingua

7378 Indonesian

7383 Icelandic

7384 Italian

7387 Hebrew

7465 Japanese

7473 Yiddish

7487 Javanese

7565 Georgian

7575 Kazakh

7576 Greenlandic

7577 Cambodian

7578 Kannada

7579 Korean

7583 Kashmiri

7585 Kurdish

7589 Kirghiz

7665 Latin

Code Language

6565 Afar

6566 Abkhazian

6570 Afrikaans

6577 Ameharic

6582 Arabic

6583 Assamese

6588 Aymara

6590 Azerbaijani

6665 Bashkir

6669 Byelorussian

6671 Bulgarian

6672 Bihari

6678 Bengali;

Bangla

6679 Tibetan

6682 Breton

6765 Catalan

6779 Corsican

6783 Czech

6789 Welsh

6865 Danish

6869 German

6890 Bhutani

6976 Greek

6978 English

6979 Esperanto

6983 Spanish

6984 Estonian

6985 Basque

7065 Persian

7073 Finnish

7074 Fiji

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1656

These displays will alert you to a missed operation or provide further instructions.

Warning and Instruction Displays

PLEASE SET CLOCK BY

PRESSING ACTION KEY

CHECK CASSETTE

RECORD TAB

NO CASSETTE

VIDEO HEADS MAY

NEED CLEANING

PLEASE INSERTHEAD

CLEANING CASSETTE

OR REFER TO MANUAL

END : PLAY

Page

CautionOSD

If you attempt to set or review a Timer Recording

and the Clock is not set...

PLEASE PREPARE

FOR TIMER REC

PLEASE CHECK THE DISC,

AND FOR STAINS OR

SCRATCHES ON DISC

TO CANCEL TIMER REC

HOLD DOWN STOP KEY

FOR APPROX 3 SEC

THIS DISC MAY NOT BE PLAYED

IN YOUR REGION

THIS TYPE OF DISC CANNOT BE

PLAYED. PLEASE INSERT A

DIFFERENT DISC

CANNOT PLAY THIS FILE

If you press REC on the remote control or DECK,

and a cassette is inserted with no record tab...

If you press PLAY, FF, REW, or REC on the

remote control or DECK without a cassette

inserted...

If you press STOP or POWER during a Timer

Recording...

(visible in VCR mode only)

If head cleaning becomes necessary while playing

back a tape...

If you press PLAY, and DECK reads data from

a stained or scratched disc in DVD mode.

Playback of a disc with different region number was

attempted. Only discs marked region “1”, “ALL”, or

those that include “1” are playable on this DECK.

An unusable disc is inserted in the unit, or the disc

is not installed with label side up.

This file format cannot be played.

(Appears during MP3/JPEG file playback)

If the DECK is not in Stop mode, or cassette is not

inserted, or cassette has no record tab, or tape is

at its end 2 minutes before a Timer Recording is

about to begin...

For Your Information

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1657

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Before Requesting Service

Power

No power…

Power turns itself off...

Recording & Playback

TV program cannot be recorded...

Timer recording cannot be

performed…

There is no playback picture, or the

playback picture is noisy or contains

streaks...

During special effects playback

picture may contain some vertical

jitter when using a TV with an

Automatic Vertical Hold Control...

DECK cannot be controlled...

Check the following points if you are having trouble with your DECK.

Solution

• Completely insert Power Plug into an AC outlet.

• Press POWER button on.

• Make sure power source is active.

• Auto power-off (shutoff) occurs after about 5 min. in

DVD mode with no operation, or if there is no

broadcast signal in TV or Playback mode.

Turn the power back on. (pp. 23, 33)

Solution

• Check connections between DECK, external antenna,

and TV.

• Check channel selections.

• Make sure your antenna system (CABLE or TV) is

correctly set. (Channels [p. 18])

• Make sure cassette record tab is intact. (p. 6)

• Confirm that clock is set to current time and date.

• Make sure Cable/DSS box (if used) is left on and tuned

to channel to be recorded.

• Set recording start/stop times correctly. (p. 24)

• Timer recording may not be performed or continued if a

power interruption occurs before or during a Timer

Recording, even after power is restored.

• Select channel 3 or 4 on TV to match VCR output

channel (3 or 4) (p. 16) or select LINE.

• Set VCR/TV selector to “VCR.”

• Adjust TRACKING control in either direction. (p. 4)

• Try Head Cleaning. (p. 4)

• Set TV’s Vertical Hold Control to MANUAL, then adjust.

• Make sure DECK power is on.

• Check Remote batteries.

• Make sure Remote is in proper mode. (p. 28)

• Make sure Timer Recording is not in progress.

Remote Control

DECK cannot be remote controlled...

PROG buttons do not respond...

Solution

• Make sure DECK power is on.

• Make sure Remote is in VCR mode.

• Aim Remote Control directly at remote sensor on DECK. (p.9)

• Avoid any object blocking signal path.

• Check Remote batteries. (p. 4)

• Exposing DECK remote sensor to direct fluorescent

or outdoor light may cause signal interference.

• PROG functions are not available in COMPONENT

Video Output and S-VIDEO OUT. Set TV to either RF

IN or VIDEO IN. (p. 10)

• Check Remote batteries. (p. 4)

• Press VCR or DVD button for DVD/VCR mode. (p. 28)

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1658

If you cannot resolve the problem, please call the Customer Call Center for product

assistance at 1-800-211-PANA (7262).

To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).

or, contact us via the web at:http://www.panasonic.com/contactinfo

Miscellaneous

Programs cannot be viewed on TV...

Video cassette cannot be inserted...

Video cassette ejects when a

recording is started or the power is

turned off for timer recording...

In Stop mode, the motor (CYLINDER)

continues to rotate...

The disc cannot be removed..

Solution

• Make sure TV is tuned to VCR's output channel (3 or 4).

• Check connections between DECK, external antenna,

and TV.

• Set VCR/TV selector to “TV.” (p. 21)

• Make sure proper signal source is selected.

• If the television is not progressive compatible, a

progressive scan picture is not available.

Connect the Video Output or S-Video Output

connector (pp. 12, 13) and set PROGRESSIVE OUT

to “OFF” in the DVD Main Menu. (p. 55)

• Insert the cassette with window side up; record tab

facing you.

• Make sure cassette record tab is intact. (p. 6)

• To enable Quick play mechanism, the cylinder will

rotate for about 3 minutes. This reduces response

time from Stop to Play mode.

• First, unplug DECK. Then, prepare a rigid wire

(e.g. an extended paper clip) and, applying moderate

force, insert it straight into the hole at the base of the

tray. The tray will eject a little. Now, pull the tray all the

way out and remove the disc. (p. 9)

DVD/ Video CD/ CD

Play fails to start even when PLAY is

pressed...

Picture is distorted during rapid

advance or rapid reverse...

No Forward/Reverse Scene Search

play...

Solution

• This DECK cannot play discs other than DVDs, Video CDs

and CDs.

• The disc may be dirty and require cleaning.

• The picture will be somewhat distorted at times:

this is normal.

• Some discs may have sections which prohibit

Forward/Reverse Scene Search. (p. 23)

Audio soundtrack and/or subtitle

language is not the one selected at

the initial settings...

No subtitles...

Alternative audio soundtrack

(or subtitle) language cannot be

selected...

Angle cannot be changed...

• If the audio soundtrack and/or subtitle language

selected at DVD initial settings does not exist

on the disc, it will not be accessible.

• Subtitles appear only when available on disc.

•“OFF” is selected at the changing subtitle language.

Select “ON” at the “Subtitle Languages” section

(p. 36) to display the subtitles.

• Alternative language cannot be selected with discs

which do not contain more than one language.

• For some discs, alternative language cannot be selected

with the AUDIO or SUB TITLE button.

Try selecting it from the DVD MAIN MENU if available.

• This function is dependent on software availability.

Even if disc has multiple angles, they may be recorded

for specific scenes only. (p. 37)

For Your Information

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1659

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Limited Warranty

PANASONIC CONSUMER ELECTRONICS COMPANY,

DIVISION OF PANASONIC CORPORATION OF

NORTH AMERICA

One Panasonic Way

Secaucus, New Jersey 07094

Panasonic DVD/VCR Deck Limited Warranty

Limited Warranty Coverage

If your product does not work properly because of a defect in materials or workmanship, Panasonic

Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)

will, for the length of the period indicated on the chart below, which starts with the date of original purchase

(“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b)

replace it with a new or a refurbished product. The decision to repair or replace will be made by the

warrantor.

During the “Labor” Limited Warranty period there will be no charge for labor. During the “Parts” warranty

period, there will be no charge for parts. You must mail-in your product during the warranty period.

If non-rechargeable batteries are included, they are not warranted. This Limited Warranty only applies to

products purchased and serviced in the United States or Puerto Rico. This Limited Warranty is extended

only to the original purchaser and only covers product purchased as new. A purchase receipt or other

proof of original purchase date is required for Limited Warranty service.

Mail-In Service

For assistance in the continental U.S.A. in obtaining repairs please ship the product to:

Panasonic Services Company

Customer Servicenter

Suite B

4900 George McVay Drive

McAllen, TX 78503

For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.

When shipping the unit carefully pack and send it prepaid, adequately insured and preferably in the original

carton. Include a letter detailing the complaint and provide a day time phone number where you can be

reached.

IF REPAIR IS NEEDED DURING THE LIMITED WARRANTY PERIOD THE PURCHASER WILL BE

REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF

PURCHASE, AMOUNT PAID AND PLACE OF PURCHSE. CUSTOMER WILL BE CHARGED FOR THE

REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.

Limited Warranty Limits And Exclusions

This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT

COVER normal wear and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT COVER damages

which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures

which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-

up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage,

modification, or commercial use (such as hotel, office, restaurant, or other business), rental use of the product, or

service by anyone other than a Factory Servicenter or other Authorized Servicer, or damage that is attributable to

acts of God.

Product or Part Name

DVD/VCR Deck

Rechargeable Batteries

(in exchange for defective item)

Labor

Ninety (90) Days

Not Applicable

Parts

One (1) Year

Ten (10) Days

PANASONIC SALES COMPANY, DIVISION

OF PANASONIC PUERTO RICO, INC.,

AVE. 65 de Infantería, Km. 9.5

San Gabriel Industrial Park

Carolina, Puerto Rico 00985

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1660

For Your Information

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY

COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH

OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove

or re-install an installed unit if applicable, travel to and from the servicer, loss of or damage to media or

images, data or other recorded content. The items listed are not exclusive, but are for illustration only.)

ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY,

ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on

how long an implied Limited Warranty lasts, so the exclusions may not apply to you.

This Limited Warranty gives you specific legal rights and you may also have other rights which vary from

state to state. If a problem with this product develops during or after the Limited Warranty period, you may

contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the

warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR

RESPONSIBILITY.

Obtain Product Information and Operating Assistance; locate your nearest Dealer

or Servicenter; purchase Parts and Accessories; or make Customer Service and

Literature requests by visiting our Web Site at:

http://www.panasonic.com/consumersupport

or, contact us via the web at:

http://www.panasonic.com/contactinfo

You may also contact us directly at:

1-800-211-PANA (7262),

Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.

Customer Services Directory

Purchase Parts, Accessories and Instruction Books online for all Panasonic

Products by visiting our Web Site at:

http://www.pasc.panasonic.com

or, send your request by E-mail to:

[email protected]

You may also contact us directly at:

1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday - Friday 9 am to 8 pm, EST.)

Panasonic Services Company

20421 84th Avenue South,

Kent, WA 98032

(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)

For hearing or speech impaired TTY users, TTY : 1-877-833-8855

Accessory Purchases

For hearing or speech impaired TTY users, TTY : 1-866-605-1277

Service in Puerto Rico

Panasonic Puerto Rico, Inc. Panasonic Sales Company

Factory Servicenter:

Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,

Carolina, Puerto Rico 00985

Phone (787)750-4300 Fax (787)768-2910

As of December 2004

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1661

INSTALACIÓN

1 PRECAUCIÓN CON LA FUENTE DE ALIMENTACIÓN

El equipo solo debe hacerse funcionar desde una fuente de a

limentación que se indique en la unidad o en este manual.

Si fuera necesario, haga revisar la fuente de alimentación de

su hogar por parte de la Compañia de Suministro Eléctrico

o por parte de su Distribuidor de Productos de Vídeo.

2 CONECTOR POLARIZADO O CON TOMA A TIERRA

Como característica de seguridad, este producto de vídeo

viene equipado con un enchufe de cable de alimentación

polarizado (solo una pata es más ancha que la otra), o con

un enchufe del tipo con toma a tierra de tres patas.

PRECAUCIÓN CON EL ENCHUFE POLARIZADO

Este enchufe sólo entrará en la toma en un sentido.

Si no pudiera introducir el enchufe a fondo, intente darle la

vuelta. Si aún así no entrara, llame a un técnico electricista

para que le instale una toma de red adecuada. No desactive

esta función de seguridad manipulando el enchufe de ninguna

manera.

PRECAUCIÓN CON ENCHUFES CON TOMA A TIERRA

Este enchufe sólo entrará en una toma con conexión a tierra de

tres orificios. Si fuera necesario, que un técnico electricista le

instale la toma de red adecuada. No desactive esta función de

seguridad manipulando el enchufe de ninguna manera.

3 CABLE DE ALIMENTACIÓN

Asegúrese de que los cables de alimentación son dispuestos

de tal forma que no se apoye nada sobre ellos, no ruede

nada sobre ellos, o que estén en el paso de tráfico al

caminar. Si se utilizara un cable alargador, asegúrese de

que también disponga de un enchufe polarizado o con toma

a tierra y de que puede conectarse firmemente. Los cables

pelados, los enchufes averiados o hilos quebrados

constituyen un peligro y deben ser reemplazados por un

técnico cualificado del servicio técnico. Las tomas eléctricas

de la red general sobrecargadas y los cables de extensión

constituyen riesgos de incendio y han de evitarse en lo

posible.

4 NO BLOQUEE LOS ORIFICIOS DE VENTILACIÓN

Las aberturas de ventilación del mueble liberan el calor

generado durante el funcionamiento de la unidad. Si se

bloquearan, el calor acumulado dentro de la unidad podría

ocasionar fallos que pueden llevar a riesgos de incendio o

daños por calor en las cassettes utilizadas.

5 EVITE UBICACIONES MUY CALIENTES O SOMETIDA

A CAMBIOS BRUSCOS DE TEMPERATURA

No coloque la unidad encima o cerca de cual quier tipo de

calefactor o regulador, bajo la luz solar directa, dentro de

vehículos, etc… No traslade la unidad súbitamente entre

sitios con variaciones extremas de temparatura. Si la unidad

es llevada bruscamente de un sitio frío a otro cálido, la

humedad puede condensarse en la unidad y en la cinta.

6 PARA EVITAR LESIONES PERSONALES

• No coloque equipos no fijados en superficies inclinadas.

• No coloque esta unidad sobre ningún soporte que no esté

firme, nivelado y que sea adecuadamente

fuerte. La unidad podría caerse y

producir graves lesiones a niños o

adultos y dañarse la unidad misma.

• La combinación de aparato y carrito

debe moverse con cuidado. Las paradas

súbitas, una fuerza excesiva ya las

superficies irregulares pueden ocasionar el vuelco de la

combinación de aparato y carrito.

• Siga atentamente las instrucciones de funcionamiento y

utilice los accesorios recomendados por el fabricante al

hacer funcionar esta unidad o al conectaria a otros

equipos.

UTILIZACIÓN DE LA UNIDAD DE VÍDEO

Si la unidad ha estado almacenada o es trasladada a una nueva ubicación, remítase

primero a la sección de INSTALACIÓN de estas medidas de seguridad.

1 MANTENGA ESTA UNIDAD DE VÍDEO ALEJADA DEL AGUA O DE

HUMEDAD DE CUALQUIER TIPO

2 SI EL EQUIPO ES EXPUESTO A LA LLUVIA, HUMEDAD, O FUERTES

IMPACTOS, desenchufe la unidad y que sea revisada por un técnico cualificado

antes de volver a utilizarla.

3 DURANTE UNA TORMENTA ELÉCTRICA

Durante una tormenta con rayos, tanto en interiores como en el exterior, o antes de

dejar la unidad sin utilizar durante largos períodos de tiempo, desconecte todos los

equipos de la fuente de alimentación así como la antena y el sistema de cableado.

4 AL ENCHUFAR LA UNIDAD

•No exponga nunca la unidad a la lluvia o el agua. NO LA HAGA FUNCIONAR

si se ha derramado líquido dentro de la unidad. Desenchufe la unida

inmediatamente ya que sea revisada por un técnico. Pueden producirse

incendios o sacudidas eléctricas derivadas de cortocircuitos eléctricos

causados por el contacto de líquidos con el interior de la unidad.

•No deje caer ni introduzca ningún objeto por las aberturas de la unidad. Algunas

piezas internas tienen un voltaje peligroso y el contacto con ellas puede producir

sacudidas eléctricas o incendios.

•Evite colocar la unidad directamente encima o debajo del televisor, ya que esto

prodría causar interferencias eléctricas. Mantenga cualquier tipo de imán

alejados de equipos electrónicos.

5 UTILIZACIÓN DE ACCESORIOS

Utilice sólo accesorios recomendados por el fabricante para así evitar riesgos de

incendio, sacudidas eléctricas y otros peligros.

6 LIMPIEZA DE LA UNIDAD

Desenchufe la unidad. Luego utilice un paño limpio y seco, sin tratamiento

químico para quitar suavemente el polvo o suciedad. NO UTILICE productos de

limpieza, aerosoles, o aire comprimido que pudieran causar un exceso de

pulverización o introducirse en la unidad y ocasionar sacudidas eléctricas.

Caulquier substancia, como cera, cinta adhesiva, etc., podría arruinar el acabado

de la superficie. La exposición a substancias grasosas, áreas húmedas o

polvorientas puede afectar de manera adversa a las piezas intemas.

INSTALACIÓN DE LA ANTENA EXTERIOR

1 CONEXIÓN SEGURA DE LA ANTENA Y DE LOS CABLES

Si se conectara una antena exterior o sistema de cable conectado al equido, el

usuario deberá asegurarse de que la antena o el

sistema de cable disponen de toma a tierra

como forma de proporcinar protección contra

la acumulación de cargas estábicas y saltos

de corrientes. La sección 810 del Código

Eléctrico Nacional, ANSI/NFPA 70 (en

Canadá, la parte 1 del Código Eléctrico

Canadiense) proporciona información con respecto a la

conexión a tierra correcta del mástil y la estructura de soporte, conexión a

tierra de los cables de bajada de antena a una unidad de descarga, tamaño de

los conductores a tierra, ubicación de la unidad de descarga de antena,

conexión de los electrodos a tierra y requisitos del electrodo de toma a tierra.

MANTENGA LA ANTENA LIBRE DE LÍNEAS O CIRCUITOS DE ALTO VOLTAJE

Un sistema de antena exterior deberá ser colocado bien alejado de líneas de

alimentación, luz eléctrica o circuitos de alimentación para que nunca esté en

contacto con tales fuentes de alimentación si se cayera. Al instalar una antena

exterior, debe tenerse muchísimo cuidado para evitar las líneas de alimentación,

circuitos u otras fuentes de alimentación ya que esto podría resultar mortal.

Debido a los riesgos implicados en la instalación de una antena, tal operación

debe dejarse a un profesional.

Medidas de seguridad y precauciones importantes

EMPALMADOR

DE CONEXIÓN

A TIERRA

EQUIPO DE

SERVICIO

ELÉCTRICO

BAJADA DE ANTENA

UNIDAD DE DESCARGA

DELA ANTENA (SECCIÓN

S10-20 DEL NEC)

CONDUCTORES CONEXIÓN

A TIERRA (SECCIÓN

S10-20 DEL NEC)

SISTEMA DE ELECTRODOS DE

CONEXIÓN A TIERRA DEL SERVICIO

ELÉCTRICO (ART, 250 DEL NEC, PARTE H)

CÓDIGOO ELÉCTRICO

NEC-NATIONAL

EMPALMADOR DE

CONEXIÓN A TIERRA

SERVICIO

1 EL USUARIO NO DEBE REALIZAR NINGUNA OPERACIÓN DE

SERVICIO TÉCNICO POR SÍ MISMO

Si, después de observar atentamente las detalladas instrucciones de

funcionamiento, este producto de vídeo no funcionara correctamente, no intente

abrir o extraer las tapas, o realizar cualquier ajuste no indicado en este manual.

Desenchufe la unidad y llévela a un técnico cualificado de servicio técnico.

2 SI FUERAN NECESARIAS PIEZAS DE RECAMBIO

Asegúrese de que el técnico de servicio utiliza sólo piezas especificadas

por el fabricante, o de las mismas características que las piezas originales.

La utilización de subsitutos no autorizados puede ser causa de incendios,

sacudidas eléctricas, u otros peligros.

3 QUE EL TÉCNICO DE SERVICIO TÉCNICO REALICE UNA

COMPROBACIÓN DE SEGURIDAD

Después de cualquier servicio o reparación de la unidad, solicite al técnico de

servicio que realice una completa comprobación de seguridad tal como se

describe en la literatura de servicio técnico del fabricante para asegurarse así

que la unidad de vídeo se encuentra en condiciones de funcionamiento seguras.

PARA REDUCIR EL RIESGO DE GOLPES ELÉCTRICOS, INCENDIOS, HERIDAS O DAÑOS A

ESTE PRODUCTO, LEA Y GUARDE TODAS LAS INSTRUCCIONES DE SEGURIDAD Y

FUNCIONAMIENTO. TENGA EN CUENTA TODAS LAS ADVERTENCIAS INDICADAS EN EL

MANUAL Y EN EL PRODUCTO.

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1662

PRECAUCIONES DE SEGURIDAD

PRECAUCION: PARA EVITAR LA POSIBILIDAD DE

UNA DESCARGA ELECTRICA NO DESMONTAR LA

CUBIERTA (O LA PARTE TRASERA). ESTE APARATO

NO PUEDE SER REPARADO POR EL PROPIETARIO.

PARA CUALQUIER TRABAJO DE SERVICIO SE

DEBE RECURRIR A UN TECNICO ESPECIALIZADO.

PELIGRO DE DESCARGA

ELECTRICA NO ABRIR

PRECAUCION

Este símbolo advierte al usuario de que hay voltaje sin

aislamiento dentro de la unidad de suficiente magnitud

como para ocasionar sacudidas eléctricas. Por lo tanto,

resultará peligroso realizar cualquier tipo de contacto

con toda pieza interna de la unidad.

Este símbolo alerta al usuario de que se ha incluido

importante literatura sobre el funcionamiento y

mantenimiento de esta unidad. Por tanto, debe leerse

atentamente tal literatura a fin de evitar cualquier

problema.

Advertencia FCC: Cualquier cambio o modificación no autorizado de este

equipo anulará la autorización al usuario para hacer

funcionar la unidad.

FCC Warning: Any unauthorized changes or modifications to this

equipment would void the user’s authority to operate.

PARA PREVENIR INCENDIOS O CHOQUES ELÉCTRICOS NO

EXPONGA ESTE APARATO A LA LLUVIA O LA HUMEDAD.

PARA PREVENIR CHOQUES ELÉCTRICOS, ASEGURASE QUE LA

CLAVIJA HAGA JUEGO CON EL ENCHUFE Y CONÉCTELO

COMPLETAMENTE.

Guía para rápida consulta

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1663

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

DVD/VCR

VHF/UHF

Estuche convertidor

de TV por cable

Televisor

Terminal

IN FROM ANT.

Entrada (IN) desde

ANT./CABLE

Terminal

OUT TO TV

Terminal IN FROM ANT.

Televisor

DVD/VCR

VHF/UHF

Terminal

OUT TO TV

Entrada (IN) desde

ANT./CABLE

Spanish Quick Use Guide/ Guía para rápida consulta

Para ajustar el idioma, canal yPara ajustar el idioma, canal y

CONEXIONES/CONFIGURACION INICIAL (READY TO PLAY)

Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.

El DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA.

CONEXIONES

Conecte el cable de la antena al terminal IN

FROM ANT del DVD/VCR.

Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con

el cable RF incluido.

Para Ant/Cable

➛➛

➛

DVD/VCR

➛➛

➛

Para Sistema Digital de Satelite (DSS)/ Convertidor de cable

➛➛

➛ DVD/VCR

➛➛

➛ TV

Conecte la salida de convertidor de cable

al terminal IN FROM ANT.

Conecte el terminal OUT TO TV del DVD/VCR

a la entrada de la antena VHF/UHF del TV con

el cable RF incluido.

CONFIGURACION INICIAL

Encienda el TV y cambie al canal 3.

Enchufe el cable de CA.

El DVD/VCR se encenderá e iniciará las

fijaciones de los canales y del reloj.

• Si no aparece la pantalla de abajo, compruebe

la conexión del DVD/VCR-TV y si el canal del

TV está a 3, intennte cambiando al canal 4.

• Para cambiar el canal de salida del DVD/VCR,

consulte las instrucciones de “Canal de salida

del VCR” (informaciones en inglés página 19).

Enchufe el cable de CA.

Si está usanndo un convertidor de TV por cable y

en su area hay un canal de Public Broadcast

Station (PBS), ajuste su convertidor al canal PBS

de su area. Si está usando un receptor DSS, este

debe estar apagado.

Al inicio, el idioma de la

pantalla está fijado a

inglés.

Para cambiar el idioma,

seleccione la pantalla

MENU (informaciones en

inglés página 18).

Nota

• Los botones de funciones no funcionan durante

la configuración inicial.

• Para retirar un cassette durante el ajuste

automático, presione EJECT en el control remoto

o STOP dos veces en el aparato. En este caso,

los ajustes de los canales y la hora se deben

hacer manualmente. Para los ajustes seleccione

la pantalla MENU (informaciones en inglés

página 18).

• Dependiendo de las condiciones, el ajuste

automático puede durar más de 30 minutos.

En ese caso, presione STOP para detener el

ajuste automático y realice los ajustes

manualmente en la pantalla MENU.

AJUSTE MANUAL DEL RELOJ

Si la fijación ha sido incompleta.

Presione la tecla ACTION en el control remoto

para visualizar la pantalla del menú SET

CLOCK.

Presione para seleccionar el mes y SET

para ajustar. De la misma forma, seleccione y

ajuste la fecha, año, hora y DST (hora de

verano).

Presione dos veces la tecla ACTION para

poner el RELOJ en marcha y salir.

Las fijaciones se realizan automáticamente.

Cuando termina las fijaciones, aparecerá la

siguiente pantalla.

Si aparece en la pantalla “AUTO CLOCK SET

IS INCOMPLETE (FIJACION AUTOMATICA

DEL RELOJ ES INCOMPLETO)”, Ajuste el

reloj como se describe a continuación.

Al usar cables coaxiales RF del tipo “tuerca”,

apriételos solamente con los dedos. Un apriete

excesivo puede dañar los terminales.

Para solicitar ayuda, por favor llame al: 1-800-211-PANA(7262) o consúltenos a través de página web en:http: //www.panasonic.com/contactinfo

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1664

Operaciones básicas para la reproducción

Inserte un cassette,

• La alimentación del DECK se activa. Si Auto

VCR/TV (consulte la página 34) está en

“INACT (OFF)”, presione VCR/TV en el control

remoto para el modo VCR.

Detalles especiales durante la grabación

Presione STOP para detener el cassette.

Presione REW/SLOW- o FF/SLOW+ en el

modo de parada para rebobinado/avance

rápido del cassette.

Presione EJECT en el control remoto,

o STOP/EJECT en el DECK para expulsar

el cassette.

Operaciones básicas para la grabación

Inserte el cassette con lengüeta de

protección de grabación (página 6).

Presione CH / , o las teclas de números

para seleccionar el canal.

Presione SPEED para seleccionar la

velocidad de grabación (página 4)

Presione STOP para detener la grabación.

• SP = Reproducción normal

• SLP = Reproducción extra larga

Grabación de un toque

Presione REC repetidamente para ajustar la

hora de grabación (30 min - 4 horas).

• La videograbadora termina la grabación

a una hora programada.

Grabación normal

0:30 1:00

1:302:003:004:00

Programación fácil para la

grabación con temporizador

1) Presion .

2) Para ajustar la FECHA

de grabación,

presione

para seleccionar:

1-31 = una vez, o

DIARIO = a la misma

hora de lunes a viernes,

SEMANA = a la misma

hora cada semana.

Presione

para seleccionar un

número que no está

usando para ingresar

mas programas y

presione SET

para ajustar.

Luego repita el paso 2.

Presione nuevamente

PROG para salir.

Fecha de hoy

Orden para elegir

Ejemplo

DIARIO

68 9

/ Orden para elegir

SEMANAL

(

)

SEMANAL

(

)

SEMANAL

(

)

Presione PLAY para reproducir el cassette.

• Si el cassette no tiene la lengüeta de

prevención de grabación (página 6), se inicia

la reproducción automáticamente.

Presione FF/SLOW+ o REW/SLOW- para

búsqueda de escenas hacia delante/ hacia

atrás. Presione PLAY para liberar.

Presione PAUSE/STILL para imagen Fija

(Congelada).

Presione PLAY para liberar.

Presione PAUSE/STILL en el modo de

imagen fija para imágenes cuadro a cuadro.

Presione PLAY para liberar.

Presione FF/SLOW+ o REW/SLOW- en el

modo de imagen fija para cambiar la

velocidad de las imágenes a cámara lenta.

Presione REC para comenzar a grabar.

• Para eliminar escenas indeseadas, presione

PAUSE/STILL para hacer una pausa, y al

presionar nuevamente continua la grabación.

• No podrá ver otro canal durante la grabación.

Presione PROG

para visualizar la pantalla de Programacion.

• La alimentación del DECK se activa. Si Auto

VCR/TV (consulte la página 32) está en

“INACT (OFF)”, presione VCR/TV en el control

remoto para el modo VCR.

3) Ajustes los ítems restantes,

presione SET para ajustar los tiempos de

INICIO/PARADA, CANAL o entrada de

LINEA (página 35), y la velocidad de la cinta

(SP, SLP).

Luego presione para seleccionar.

Presione PROG para finalizar PROGRAM.

PARADA

VEL

ELEG

FIJAR : SET

TERM

NAR

: PROG

Guía para rápida consulta

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1665

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Presione para seleccionar el ajuste

deseado.

Presione

SET

para ajustar.

Para volver a la pantalla normal,

Presione repetidamente

DISPLAY

Funcionnamiento del DVD utilizando

visualizaciones en pantalla

Presione

DISPLAY

en el modo reproducción

o parada para visualizar las visualizaciones

en pantalla.

• Cada vez que se presione

DISPLAY

,la

visualización en pantalla cambia como se

muestra a continuación.

Presione (o ) para seleccionar el

ítem deseado.

Presione

SET

para ajustar.

Spanish Quick Use Guide/ Guía para rápida consulta

■ Para buscar una escena particular

Búsqueda hacia adelante

Presione

FF/SLOW+

en el modo de

reproducción.

Búsqueda hacia atrás

Presione

REW/SLOW-

en el modo de

reproducción.

(Para liberar, presione

PLAY

)

■ Para saltar un capítulo o una pista

Salto hacia adelante

Presione

SKIP

l en el modo de

reproducción.

Salto hacia atrás

Presione l

SKIP

en el modo de

reproducción.

■■

■ Para ver una imagen fija

Presione

PAUSE/STILL

durante la

reproducción.

(Para liberar, presione

PLAY

)

■ Para ver imágenes cuadro a cuadro (DVD/CD-Vídeo)

Presione

PAUSE/STILL

en el modo de imagen fija.

La imagen avanza un cuadro cada vez que

presiona la tecla. (Para volver a la

reproducción normal, presione

PLAY

)

■ Para ver en cámara lenta (DVD/CD-Vídeo)

Presione

FF/SLOW+

REW/SLOW-

en el

modo de imagen fija.

(Para liberar, presione

PLAY

)

Operaciones básicas del DVD

Presione

DVD

para seleccionar el modo DVD.

1) Presione

OPEN/CLOSE

2) Ponga un disco en la bandeja de disco.

• Sujete el disco sin tocar ninguna de sus

superficies, póngalo con el lado donde esté

impreso el título hacia arriba, alinéelo con las

guías y póngalo en su posición apropiada.

Disco de 3” (8 cm) / Disco de 5” (12 cm)

Presione

PLAY

para iniciar la reproducción.

La bandeja del disco se cierra

automáticamente.

• Si está usando un DVD interactivo y aparece

el menú de títulos (TITLE MENU), siga al

paso 4.

Presione o las teclas numéricas

para seleccionar el artículo deseado.

Presione

SET

PLAY

para la reproducción.

Si usa las teclas numéricas, la

reproducción comienza automáticamente.

Presione

STOP

para parar la reproducción.

Presione

OPEN/CLOSE

para expulsar el

disco.

Cuando se presiona DISPLAY, la visualización en

pantalla muestra la información del disco (título /

capítulo / número de lista, tiempo transcurrido de

reproducción, audio / idioma del subtítulo, y ángulo)

e información (repetir la reproducción, modo

reproducción, Karaoke vocal encendido / apagado,

etc.).

Información seleccionada del disco

Información seleccionada del DECK

Pantalla normal

➡

Para solicitar ayuda, por favor llame al: 1-800-211-PANA(7262) o consúltenos a través de página web en:http: //www.panasonic.com/contactinfo

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1666

Cambio del idioma de subtítulos

[Vídeo DVD solamente]

EI idioma de los subtítulos seleccionado al hacer

las fijaciones iniciales se puede cambiar por otro

idioma diferente, si éste se encuentra disponible.

Selección de IDIOMAS DEL

DISCO [DVD solamente]

Presione para seleccionar el artículo

deseado.

Presione

SET

Volver a visualizar el menú de DVD para

continuar el ajuste.

Presione

ACTION

y pase al paso 3 para

ajustar otro ajuste o, para salir,

presione

ACTION

dos veces.

Presione DVD para seleccionar el modo DVD.

Presione ACTION en el modo de parada

para visualizar MENU.

Presione para seleccionar el artículo

deseado.

Presione

SET

Fijaciones iniciales

IDIOMAS DEL DISCO

Todos los idiomas ofrecidos en el disco

pueden ser ajustados. Si el idioma ajustado

no es ofrecido en el disco, se seleccionará el

idioma original del disco.

SALIDA DE AUDIO

Puede usted ajustar la salida audio

procedente del terminal de salida audio digital.

DETENER RASTREO

Para seleccionar “CAMPO”, “CUADRO” o

“AUTO” para prevenir inestabilidad o para

permitir ver textos pequeños o patrones finos

claramente en el modo de imagen fija.

TV PREFERENCIA

Para seleccionar cuando el material del vídeo

es para pantalla ancha y se quiere reproducir

en el estilo Pan&Scan, en el estilo Letterbox o

en el estilo 16:9 en la pantalla.

SALIDA PROGRESIVA

Puede ajustar el conector de salida de video

componente para la emisión de señal de

exploración progresiva.

Presione

SUBTITLE

durante la reproducción.

Cuando no haya subtítulos

grabados, se visualizará “-”

en lugar del número de

idioma.

Seleccione “AUDIO”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonés :

Original : Se seleccionará el idioma original

de cada disco.

OTRO 0000 : Se puede seleccionar el otro

idioma.

Seleccione “SUBTITULO”

AUTO : Se seleccionará el mismo que fue

seleccionado en la preparación de

“AUDIO”. (Fijación de fábrica)

• Si el idioma seleccionado en la preparación de

“AUDIO” se utiliza durante la reproducción, los

subtítulos no aparecerán.

• Si se utiliza otro idioma durante la reproducción,

los subtítulos aparecerán en el idioma

seleccionado en la preparación de “AUDIO”

Inglés / Español / Francés / Japonés :

OTRO 0000 : Se puede seleccionar el otro

idioma.

Seleccione “MENU”

(Fijación de fábrica : inglés)

Inglés / Español / Francés / Japonés :

OTRO 0000 : Se puede seleccionar el otro

idioma.

Visión desde otro ángulo

[DVD solamente]

Presione

ANGLE

durante

la reproducción para

visualizar la selección del

ángulo.

Algunos discos DVD tienen escenas que han

sido filmadas simultáneamente desde ángulos

diferentes.

Con estos discos, la misma escena podrá verse

desde cada uno de estos ángulos diferentes

utilizando el botón ANGLE.

Guía para rápida consulta

Presione

SUB TITLE

repetidamente, , o las

teclas numéricas para

seleccionar el idioma

deseado.

Presione

ANGLE

repetidamente, , o las

teclas numéricas para

seleccionar el ángulo

deseado.

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1667

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Presione

TITLE

durante la reproducción.

Ahora se visualiza una lista de los títulos del

disco.

Utilización de un menú de títulos

[DVD solamente]

TLE MENU

Cas

Love

Dogs

of the world

Ampliación de la imagen [DVD solamente]

Durante la reproducción de un DVD, puede ampliar

partes específicas de una imagen y seleccionar la

relación de zoom usando el botón ZOOM.

Presione

ZOOM

repetidamente para cambiar el

tamaño de la imagen como se indica a continuación:

■ Use los botones , , y para desplazar

la posición hacia arriba, hacia abajo, hacia

la izquierda o hacia la derecha.

Utilización de un menú de DVD

[DVD solamente]

Spanish Quick Use Guide/ Guía para rápida consulta

Algunos discos con películas, vienen con dos o

más títulos. Por ejemplo, si el disco tiene un

menú de títulos grabados, el botón TITLE podrá

utilizarse para seleccionar el título de la película.

Presione o las

teclas de números para

seleccionar el título

deseado.

Presione

SET

PLAY

para elegir.

Algunos discos DVD ofrecen un menú especial.

Este menú incluye guías para contenidos únicos,

audio, subtitulos, idiomas, etc.

Aunque los contenidos y las operaciones se

cambian, los siguientes son unos pasos básicos

para el uso del menú.

Presione

durante la reproducción.

El menú de DVD introducido en el disco se

visualiza ahora.

Presione o las

teclas de números

para

seleccionar el ítem deseado.

Presione

SET

PLAY

para elegir.

DVD MENU

3 . ANGLE

1 . SUBT

TLE

2 . AUD

Cambio del idioma de la pista

de sonido [DVD solamente]

EI idioma de la pista de sonido seleccionado al

hacer las fijaciones iniciales se puede cambiar

por otro idioma diferente, si éste se encuentra

disponible.

Selección de vocal para los discos de

Karaoke [DVD/CD-Vídeo solamente]

Presione

AUDIO

durante la reproducción

para visualizar la pantalla AUDIO.

Presione para

seleccionar VOZ y

presione

AUDIO

para seleccionar tal como

se indica a continuación.

Presione

AUDIO

durante la

reproducción para visualizar

SONIDO en la pantalla.

Para solicitar ayuda, por favor llame al: 1-800-211-PANA(7262) o consúltenos a través de página web en:http: //www.panasonic.com/contactinfo

Presione

AUDIO

repetidamente, , o las

teclas numéricas para

seleccionar el idioma

deseado.

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1668

Presione

POWER

en el control remoto

o DECK.

Presione

OPEN/CLOSE

y a continuacion

coloque un disco MP3/JPEG en la bandeja de

discos.

Presione

OPEN/CLOSE

para cerrarla.

Se visualizará el MENU MP3/JPEG y la

ejecución se iniciará automáticamente.

(Se visualizará el directorio del CD.)

Estado de la

función

MODO DE REPRODUCCIÓN

Area de las

carpetas

Area de

archivos

Carpeta

principal

(La carpeta

visualizada

actualmente

se volverá

verde)

(El archivo/

la carpeta

se visualiza

con un

cursor.)

:Archivo MP3 :Archivo JPEG

:Carpeta :Carpeta principal

■ Ejecución MP3/JPEG (Durante el modo

STOP)

Presione para seleccionar un archivo

MP3 ( ) o un archivo JPEG ( ), y

presione

SET

PLAY

• MP3

Búsqueda hacia adelante/hacia atrás

➡ Presione

FF/SLOW+

REW/SLOW-

durante la ejecución.

Salto de pista hacia adelante/hacia atrás

➡ Presione

SKIP+

| o

SKIP-

durante la ejecución.

• JPEG

Búsqueda siguiente/anterior

➡Presione

SKIP+

| o

SKIP-

| .

Inicie la muestra-diapositiva

➡Presione

FF/SLOW+

REW/SLOW-

Ampliar una imagen ➡ Presione

ZOOM

Girar una imagen ➡ Presione

ANGLE

Presione

STOP

para detener la operación

descrita arriba.

■ Seleccione MODO DE REPRODUCCION

(Durante el modo STOP)

Presione para seleccionar el MODO

DE REPRODUCCIÓN deseado.

[MODO DE REPRODUCCIÓN]

NORMAL:

Todos los archivos se reproducen sólo

una vez.

REPETICION DE UNA MUSIC:

El archivo seleccionado se reproduce

repetidamente.

REPETICION DE UN ARCHIVO:

Los archivos que se encuentran en la

carpeta seleccionada se reproducen

repetidamente.

REPETICION DEL DISCO:

Todos los archivos se reproducen

repetidamente.

Funcionamiento de la ejecución de MP3/JPEG

Puede utilizar esta unidad para reproducir audio de

formato MP3/JPEG, grabado para uso personal

con una computadora, etc., en un CD-ROM o

CD-RW. La ejecución no podrá realizarse en

algunos casos, debido a las condiciones de la

grabación.

Presione

ACTION

para regresar al

DVD MENU PRINCIPAL.

Guía para rápida consulta

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1669

For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo

Index

A ACTION button ................................ 8, 18

Accessories ........................................... 4

ADD/DELETE button

(Add or Delete a Channel) ............ 8, 19

Audio Broadcast types

(Stereo/SAP/Mono) ........................... 26

Audio Mode (Playback, Recording) ... 27

Auto Operation Functions ................... 31

Auto Shut-Off ....................................... 33

B Batteries ................................................ 4

C Channel (“SET UP CHANNEL”) ......... 18

Channel Up/Down,

Tracking/V-Lock Button ....................4, 8

Clock (“SET CLOCK”) ......................... 18

CM/ZERO SEARCH button ............. 8, 30

Commercial Skip ................................. 30

Connections ................................ 12 ~ 15

Copy Your Tapes (Dubbing) ............... 35

COUNTER RESET button............... 8, 30

Customer Services Directory .............. 61

D DISPLAY button .............................. 8, 11

DST (Daylight Saving Time) ............... 19

E EJECT button .................................. 8, 20

ENTER button

(For tuning TV Channel) ............... 8, 28

F FAST FORWARD/SLOW+ button .... 8, 20

H Head Cleaning ...................................... 4

I Index Search ....................................... 30

Initial Setup (Ready to Play) ......... 16, 17

INPUT button ................................... 8, 35

L Limited Warranty .......................... 60, 61

Light-up Indicators .............................. 11

Location of Controls

(Remote, DECK) .......................... 8 ~ 10

M Multi-Brand Control ....................... 28, 29

O On-Screen Displays (VCR) ................. 11

One Touch Recording......................... 21

DECK & VCR

P PLAY button (Playback a Tape) ..... 8, 20

POWER button ...................................... 8

PROG button (PROGRAM) ............. 8, 24

Program Clear, Review, Replace....... 25

Q Quality Picture ....................................... 4

R REC button (Record on a Tape)..... 8, 21

Record Tab............................................ 6

Remote Sensor ..................................... 9

Repeat Play ......................................... 31

Reset All Memory Functions ................. 9

REWIND/SLOW- button .................. 8, 20

S SAP/Hi-Fi ............................................. 27

SEARCH button .............................. 8, 30

Spanish Quick Use Guide........... 62 ~ 69

Specifications ........................................ 7

SPEED button ................................. 8, 21

Still (Freeze) Picture............................ 20

STILL/PAUSE button (Still Picture) .. 8, 20

STOP button .................................... 8, 20

T Tape Position, Tape Status ................. 32

Tape Select ......................................... 32

Timer Recording.................................. 24

Trouble Shooting........................... 58, 59

TV mode button ............................... 8, 28

V VCR mode button ............................ 8, 28

VCR/TV button................................. 8, 21

VCR/TV Selection Feature.................. 34

VOLUME +/- button (TV Volume) ... 8, 28

W Warning and Instruction Displays....... 57

Weak Signal Display ........................... 33

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1670

A ACTION button ................................ 8, 52

ANGLE button

(Multiple Angle Viewing) ......... 8, 37, 51

AUDIO button

(Audio Soundtrack Language) ..... 8, 36

Audio Output

(For Selecting Audio Output) ............ 53

Auto-Power Off Function ..................... 23

C CLEAR button ........................... 8, 38, 40

Component Video Output ............. 10, 13

D Direct Navigator .................................. 42

Disc Languages .................................. 52

DISPLAY button

(“On-Screen Display”) ................... 8, 44

DTS ...................................................... 14

DVD Menu ........................................... 41

DVD mode button ............................ 8, 28

DVD-RAM (DVD-VR) .................... 42, 43

F Frame by Frame Picture ...................... 23

Forward/Reverse Chapter/Track Skip .. 23

Forward/Reverse Scene Search ......... 23

J JPEG ............................................ 49 ~ 51

K Karaoke

(Vocal Selection for Karaoke Discs) ... 37

L Language Code List ........................... 56

M MENU button

(To display DVD Menu)................. 8, 41

MP3 ...................................................... 49

Multiple Angle Viewing ....................... 37

O OPEN/CLOSE button ...................... 8, 22

Optical Digital Audio Output ......... 10, 15

P PLAY button (Play a Disc)............... 8, 22

Play List ............................................... 43

Program Play (For Video CD/ CD) ..... 38

Progressive Scan .................... 10, 13, 55

DVD

R Random Play (For Video CD/ CD) ..... 40

Repeat Play ................................... 47, 48

Resume Function ................................ 23

RETURN button .............................. 8, 22

Rotation ............................................... 51

S SKIP+

l or SKIP- l button

(Forward/Reverse Chapter/Track) . 8, 23

Slide-show........................................... 50

SLOW+/SLOW- button

(Slow Motion Picture) .................... 8, 23

STILL/PAUSE button

(Still Picture or Pause) .................. 8, 23

Still Mode

(For selecting “FIELD” or “FRAME”).54

STOP button .................................... 8, 22

SUB TITLE button

(For selecting Subtitle Language) .. 8, 36

S-Video Out ................................... 10, 13

T TITLE button (Title Menu) ............... 8, 41

TV Mode

(For selecting the screen display style) .. 54

V Video CD ............................................. 23

V.S.S. (Virtual Surround Sound)..... 8, 23

Z ZOOM button (Picture Zoom) .... 8, 37, 51

For Your Information

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1671

Printed in Indonesia

LSQT0907 A

S1204-0

Panasonic Consumer Electronics Company,

Division of Panasonic Corporation of North America

One Panasonic Way Secaucus, New Jersey 07094

Panasonic Sales Company (“PSC”),

Division of Panasonic Puerto Rico, Inc.

Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,

Puerto Rico 00985

LSQT0907 A

PV-D4735S P36-72 (041224).p65 2004/12/24, 13:1672

Panasonic PVD4745S Manual de usuario

Marca: Panasonic

Modelo: PVD4745S

Categoría: Reproductores de DVD

Tipo: Manual de usuario

Descargar PDF

informe

En otros idiomas

English: Panasonic PVD4745S User manual

Panasonic PVD4745S Manual de usuario

Panasonic PVD4745S Manual de usuario

En otros idiomas

Documentos relacionados

Otros documentos