Hitachi DV PF74U Manual de usuario

Hitachi
Marca
Hitachi
Modelo
DV PF74U
Categoría
Reproductores de DVD
Tipo
Manual de usuario
English
Español
POWER/STANDBY
LINES
VIDEO IN L [mode] AUDIO IN R
REW F. FWD
STOP/EJECT
PLAY
REC/OTR
REC TIMER
PROGRESSIVE SCAN
DIGITAL AUTO TRACKING
DVD/VCR Combo DV-PF74U
MP3 / JPEG PLAY BACK DVD / CD / CD-R / CD-RW COMPATIBLE
STOP PLAY
OPEN/CLOSE
CHANNEL
VCR
OUTPUT
DVD
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
DVD/VCR Combo (DVD PLAYER with VIDEO
CASSETTE RECORDER)
INSTRUCTION MANUAL
Instruction manual
To obtain the best performance and ensure years of trouble-
free use, please read this instruction manual completely.
MODEL
DV-PF74U
HITACHI AMERICA, LTD.
HOME ELECTRONICS DIVISION
900 Hitachi Way
Chula Vista, CA 91914-3556
Service Hotline: 1-800-HITACHI
H9651UD.qx3 04.3.2 8:53 PM Page 1
–
2
–
EN
1L25
WARNING
:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to
possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO
NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the pres-
ence of important operating and maintenance
(servicing) instructions in the literature accom-
panying the appliance.
CAUTION
:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.
The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
H9651UD.qx3 04.3.2 8:53 PM Page 2
–
3
–
EN
1L25
English
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol clean-
ers. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted ser-
vice and, that for some specific reason, such as the possibil-
ity of the loss of an authorization code for a CATV convert-
er, is not intended to be unplugged by the user for cleaning
or any other purpose, may exclude the reference to unplug-
ging the appliance in the cleaning description otherwise
required in item 5.
6. Attachments - Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
8. Accessories - Do not place this video product on an unstable
cart, stand, tripod, bracket, or table. The
video product may fall, causing serious
injury to a child or adult, and serious
damage to the appliance. Use only with a
cart, stand, tripod, bracket, or table rec-
ommended by the manufacturer, or sold
with the video product. Any mounting of
the appliance should follow the manufac-
turer's instructions and should use a
mounting accessory recommended by the manufacturer. An
appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the appliance and cart combination to overturn.
AMEUBLES- Cet appareil ne doit être placé que sur un
meuble (avec ou sans roulettes) recommandé par le fabri-
cant. Si vous l’installez sur un meuble à roulettes, déplacez
les deux ensembles avec précaution. Un arrêt brusque, l’u-
tilisation d’une force excessive et des surfaces irrégulières
risquent de déstabiliser l’ensemble et de le renverser.
9. Ventilation - Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the video
product and to protect it from overheating, and these open-
ings must not be blocked or covered. The openings should
never be blocked by placing the video product on a bed,
sofa, rug, or other similar surface. This video product should
not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the manufac-
turer's instructions have been adhered to.
10. Power Sources - This video product should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power compa-
ny. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is equipped
with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your elec-
trician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be rout-
ed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular atten-
tion to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or cable
system is connected to the video product, be sure the anten-
na or cable system is grounded so as to provide some pro-
tection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
No. 70, provides information with regard to proper ground-
ing of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding
electrode. (Fig. A)
14. Lightning - For added protection for this video product dur-
ing a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall out-
let and disconnect the antenna or cable system. This will pre-
vent damage to the video product due to lightning and
power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other elec-
tric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the video product.
18. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19. Damage Requiring Service - Unplug this video product from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any
way.
f. When the video product exhibits a distinct change in perfor-
mance this indicates a need for service.
20. Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteris-
tics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to
this video product, ask the service technician to perform
safety checks to determine that the video product is in prop-
er operating condition.
22. Heat - This video product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND
CLAMP
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
H9651UD.qx3 04.3.2 8:53 PM Page 3
–
4
–
EN
1L25
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in accordance with
your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concern-
ing chemical wastes.
Alliance: www.eiae.org
The serial number of this product may be found on the back of the DVD/VCR. This serial number is unique to your machine.
You should record the number and other vital information here and retain this book as a permanent record of your purchase
to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protec-
tion technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings
: Description refers to playback or recording of video cassette tapes.
: Description refers to playback of DVD video discs.
: Description refers to playback of audio CDs.
: Description refers to playback of MP3 discs.
: Description refers to viewing of JPEG discs.
: Description refers to the items to be set in the QUICK mode.
QUICK
JPEG
MP3
CD
DVD
VCR
SUPPLIED ACCESSORIES
Remote control
DV-RMPF74U(TS18856)
Two AA batteries A/V cables
(approx. 3 feet (100 cm)
long) (TE14751)
+
1
0
3
M
O
D
E
2
S
E
A
R
C
H
9
Z
O
O
M
D
I
S
P
L
A
Y
8
A
U
D
I
O
0
T
O
P
M
E
N
U
S
E
T
U
P
P
L
A
Y
S
K
I
P
C
H
C
H
56
1
A
-
B
R
E
P
E
A
T
R
E
P
E
A
T
7
C
L
E
A
R
/
C
.
R
E
S
E
T
S
U
B
T
I
T
L
E
/
T
I
M
E
R
M
O
D
E
A
N
G
L
E
D
V
D
V
C
R
/
T
V
D
I
S
C
N
A
V
I
G
A
T
I
O
N
V
C
R
S
L
O
W
S
P
E
E
D
R
E
C
R
E
T
U
R
N
M
E
N
U
S
T
O
P
T
V
P
O
W
E
R
V
I
D
E
O
/
T
V
4
S
U
R
R
O
U
N
D
P
A
U
S
E
/
S
T
E
P
V
O
L
TV
E
N
T
E
R
E
J
E
C
T
O
P
E
N
/
C
L
O
S
E
(5857952)
RF Cable
NOTICE FOR PROGRESSIVE SCAN OUTPUTS
Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be dis-
played in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the ‘stan-
dard definition’ output. If there are questions regarding our TV set compatibility with this model 525p DVD player, please contact our cus-
tomer service center.
H9651UD.qx3 04.3.2 8:53 PM Page 4
–
5
–
EN
1L25
English
TABLE OF CONTENTS
■ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
■ IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
NOTICE FOR PROGRESSIVE SCAN OUTPUTS . . . . . . . . . 4
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4
■ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
■ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
■ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PLAYABLE DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
■ OPERATING CONTROLS AND FUNCTIONS . . . . . . . . . . . 8
FRONT PANEL DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 12
LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 12
■ VCR/DVD SWITCHING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
■ HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DVD/VCR TO TV CONNECTION . . . . . . . . . . . . . . . . . . . . 13
RF OUTPUT CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
CONNECTION TO AN AUDIO SYSTEM . . . . . . . . . . . . . . 14
CONNECTION TO A TV (FOR VIDEO) . . . . . . . . . . . . . . . 15
■ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 16
TO CHANGE THE ON-SCREEN LANGUAGE . . . . . . . . . . 17
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
■ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NORMAL PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 18
SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
■ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 19
NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OTR (One Touch Recording) . . . . . . . . . . . . . . . . . . . . . . . . . 19
TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 20
■ SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 21
MTS (Multi-Channel Television Sound) SYSTEM. . . . . . . . . 21
AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
REAL TIME TAPE COUNTER . . . . . . . . . . . . . . . . . . . . . . 22
■ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
INDICE
■ CONTROLES DEL FUNCIONAMIENETO Y SUS FUNCIONES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
■ CAMBIO DE VCR/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
■ CONEXIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DVD/VCR A CONEXION DE TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CANAL DE SALIDA RF
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONEXION A UN SISTEMA DE AUDIO
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
CONEXION A UN TV (PARA VIDEO)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
■
PREPARACIÓN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
PREPARACION DE UN CANAL AUTOMATICO
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
PREPARACION DE RELOJ
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
■ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
REPRODUCCIÓN BÁSICA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
DISC NAVIGATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DISC MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 23
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
FAST FORWARD / REVERSE SEARCH . . . . . . . . . . . . . . . 23
SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . . . . . . 24
ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TRACK SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
TITLE / CHAPTER SEARCH. . . . . . . . . . . . . . . . . . . . . . . . 24
TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . 25
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
PROGRAM (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
RANDOM PLAYBACK (CD) . . . . . . . . . . . . . . . . . . . . . . . . 26
MP3 / JPEG PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SLIDE SHOW MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PROGRAM (MP3 / JPEG) . . . . . . . . . . . . . . . . . . . . . . . . . . 27
RANDOM PLAYBACK (MP3 / JPEG) . . . . . . . . . . . . . . . . . 27
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 28
PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
■ DVD SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
AUDIO SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 30
VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
TO RETURN ALL SELECTIONS OF SETUP
(except for PARENTAL) TO THEIR DEFAULT SETTINGS
. . 31
■ TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . 32
■ MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
■ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
H9651UD.qx3 04.3.2 8:53 PM Page 5
–
6
–
EN
1L25
FEATURES
Mode
¡Progressive Scan system
¡Dolby Digital sound
By hooking this DVD/VCR up to a Multi-channel Dolby
Digital decoder, you can enjoy high-quality Dolby Digital
5.1ch surround sound as heard in the movie theaters.
¡Still/fast/slow/step playback
¡Random playback for audio CD, MP3, and JPEG
¡Program playback for audio CD, MP3, and JPEG
¡DVD menus in a desired language
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input from
the DVD/VCR for five minutes in the stop mode. When the
screen saver program is activated for 30 minutes, the power is
automatically turned off.
¡Subtitles in a desired language
¡Selecting a camera angle
¡Choices for audio language and sound mode
¡Parental lock
¡Automatic detection of discs
This DVD/VCR automatically detects if the loaded disc is
DVD, audio CD, MP3, or JPEG disc.
¡Playing an MP3 disc
¡Displaying a JPEG picture
This DVD/VCR plays back still images stored in JPEG
format on CD-R/RW.
¡Direct Search
¡DTS (Digital Theater System)
You can enjoy 5.1 channel surround system developed by
the Digital Theater System co. which reproduces the orig-
inal sound as truthfully as possible.
External DTS decoder required.
¡On-screen display
Information about the current operation can be displayed on
the TV screen, allowing you to confirm the currently active
functions (such as program playback), on the TV screen using
the remote control.
¡Search
Chapter search / Title search / Track search / Time search
¡Repeat
Chapter / Title / Track / Group / All / A-B
DVD
¡Zoom
¡Marker
The part designated by user can be called back.
¡
Disc Navigation
Displays the first scenes of each chapter in a title.
¡Resume Play
¡Virtual Surround
¡Component Video Out Jacks
Jacks located on the back of the DVD/VCR which are used
to send high-quality video to a TV via Component Video In
Jacks.
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Black Level Setting
Mode
Hardware specifications
¡Auto Head Cleaner
¡4 Head HiFi Stereo
¡Trilingual on-screen menu display selectable in
English, French, or Spanish
¡181 channel capability PLL frequency synthesizer
tuner with direct station call
(A cable converter box may be necessary to view scrambled
cable channels.)
Automatic functions
¡Auto power on system
Automatically turns on the DVD/VCR when you insert a
cassette.
¡Digital Auto Tracking (DTR)
Playback
¡Auto Repeat
¡2 Step Picture Search Operation
¡Index Search
¡Time Search
Recording
¡1 Year, 8 events (including Daily and Weekly Timer
Recording)
¡OTR (One Touch Recording)
VCR
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
Selecting Progressive Scan (525p/480p or Interlaced 525i/480i) Playback
¡If your TV is compatible with progressive scanning (525p/480p), connect the TV to the COMPONENT
VIDEO OUT jacks of this unit (refer to page 15), and set to the progressive scanning mode by pressing PLAY
for more than 5 seconds on the front of the unit. “P. SCAN” will appear on display of the unit.
¡To set to the interlace mode, press PLAY for more than 5 seconds on the front of the unit. “P.SCAN” will
disappear on display of the unit.
¡If your TV is not compatible with progressive scanning, keep this unit in the interlace mode (Make sure that
“P.SCAN” on display of the unit lights off).
¡Use a commercially available adaptor if the video input jacks of your TVs or monitors are the BNC type.
What is Progressive Scanning?
¡Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in
higher resolution than that of traditional (525i/480i) television signals.
“DTS” and “DTS Digital Out” are trademarks of Digital
Theater Systems, Inc.
H9651UD.qx3 04.3.2 8:53 PM Page 6
–
7
–
EN
1L25
English
ABOUT THE DISCS
The following discs can be played back on this DVD/VCR.
¡
DVD video
¡
DVD-R*
¡
Audio CD
¡
CD-R/RW*
¡
MP3 disc*
¡
JPEG disc
* Depending on the types or the writing method of the medium some
discs may not be played.
• Some DVD-R or CD-R/RW discs made on personal computers, or
on DVD recorders may not be played back properly due to factors
such as scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played back proper-
ly due to different environments or the settings of the application you
use. We recommend always to use the standardized, properly formatted
discs. (Please contact the sales agency for more detail).
• You can play back discs which bear the marks on page 33. If you
use nonstandardized discs, this unit may not play them back.
Even if they are played back, the sound or video quality will be
compromised.
•
This DVD/VCR conforms to the NTSC color system. You cannot play
discs recorded in other color systems such as PAL or SECAM.
¡Some discs include region codes as shown below.
¡The number inside the symbol refers to a region of the world, and
a disc encoded in a specific region format can only be played back
on DVD/VCR with the same region code.
¡
On the following discs, only the sound can be heard
(picture cannot be viewed).
CDV
CD-G
¡
NEVER play back the following discs. Otherwise, mal-
function may result!
DVD-RAM
CD-I
Photo CD
Video CD
DVD with region codes other than 1 or ALL
DVD-ROM for personal computers
CD-ROM for personal computers
¡
On the following disc, the sound may not be heard.
Super Audio CD
Note: Only the sound recorded on the normal CD
layer can be delivered.
The sound recorded on the high density Super
Audio CD layer cannot be delivered.
¡
Any other discs without compatibility indications.
PLAYABLE DISCS
[
DVD
]
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions on
some DVDs take priority over user operations on this
DVD/VCR. If a function you select does not run as
desired, refer to the manual accompanying the disc.
DISC TYPES
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Chapter 4
[
AUDIO CD
]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
[
MP3/JPEG
]
Data on an MP3 or JPEG disc is divided into sections
called "groups", and then into subsections called "tracks",
each of which is given a group or track number.
Example
Group 1 Group 2
Track 1 Track 2 Track 5 Track 6Track 3 Track 4
INSTALLATION LOCATION
For safety and optimum performance of your DVD/VCR:
• Install the DVD/VCR in a horizontal and stable position. Do not
place anything directly on top of the DVD/VCR. Do not place the
DVD/VCR directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of
intense heat. Avoid dusty or humid places. Avoid places with
insufficient ventilation for proper heat dissipation. Do not block the
ventilation holes on the sides of the DVD/VCR. Avoid locations
subject to strong vibration or strong magnetic fields.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
PRECAUTIONS
• Do not pull on the power cord when disconnecting it from AC wall
outlet. Grasp it by the plug.
• If, by accident, water is spilled on your DVD/VCR, unplug the power
cord immediately and take the unit to our Authorized Service
Center for servicing.
• Do not put your fingers or objects into the DVD/VCR cassette hold-
er.
MOISTURE CONDENSATION WARNING
Moisture condensation may occur inside the unit when it is moved
from a cold place to a warm place, or after heating a cold room or
under conditions of high humidity. Do not use the DVD/VCR at least
for 2 hours until its inside is dry.
H9651UD.qx3 04.3.2 8:53 PM Page 7
–
8
–
EN
1L25
OPERATING CONTROLS AND FUNCTIONS
POWER/STANDBY
LINES
VIDEO IN L [mode] AUDIO IN R
REW F.FWD
STOP/EJECT
PLAY
REC/OTR
REC TIMER
PROGRESSIVE SCAN
DIGITAL AUTO TRACKING
DVD/VCR Combo DV-PF74U
MP3 / JPEG PLAY BACK DVD / CD / CD-R / CD-RW COMPATIBLE
STOP PLAY
OPEN/CLOSE
CHANNEL
VCR
OUTPUT
DVD
1
3
4
2
681012
14
20
791113
17
15
5
18
16
19
FRONT PANEL
REMOTE CONTROL
+10
EJECT
32
SEARCH MODE
OPEN/CLOSE
9
ZOOM
DISPLAY
8
AUDIO
0
TOP MENU
SETUP
PLAY
SKIP
CH
56
1
A-B REPEAT
REPEAT
7
CLEAR/C. RESET
SUBTITLE
MODE
ANGLE
DVD
VCR/TV
DISC
NAVIGATION
VCR
SLOW SPEED REC/OTR
RETURN
MENU
STOP
4
SURROUND
PAUSE/STEP
ENTER
TIMER
22
21
23
24
25
26
27
28
29
30
32
31
33
52
53
51
48
49
50
35
38
37
46
44
45
47
43
42
39
41
40
36
34
1. POWER/STANDBY Button [page 16]
Press to turn the power on and off.
2. CASSETTE COMPARTMENT
3. OPEN/CLOSE Button [page 22]
Press to insert discs into or remove them from the tray.
4. Disc loading tray
5. PLAY Button (DVD) [page 22]
Press to begin playback.
Press to switch between progressive mode and interlace
modes.
6. STOP Button (DVD) [page 22]
Stops operation of the disc.
7. DVD OUTPUT Light (Green) [page 12]
This light appears when the DVD output mode is selected.
You can only watch DVDs when the green DVD OUTPUT
Light is on. To make the green DVD OUTPUT light come
on, press DVD on the remote control or OUTPUT on the
front panel.
8. OUTPUT Button [page 12]
Press to select DVD mode or VCR mode.
● You can switch the output mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However, if you press
OUTPUT on the front panel first, you need to re-
select the corresponding mode by pressing DVD or
VCR on the remote control.
9.
VCR OUTPUT Light (Green) [page 12]
This light appears when the VCR output mode is selected.
You can only watch tapes when the green VCR OUTPUT
light is on. To make the green VCR OUTPUT light come
on, select VCR on the remote control or OUTPUT on the
front panel.
10. CHANNEL Buttons [page 19]
In VCR mode, press to change TV channels on the DVD/VCR;
press to adjust the tracking during normal or slow motion play-
back; press to remove vertical jitter in a Still picture.
11. Display, Remote Sensor Window
12. TIMER Light [page 20]
This light glows when the DVD/VCR is in standby mode or
off for a timer recording or during an One Touch Recording.
It flashes if TIMER is pressed for a timer recording, but
there is no tape in the DVD/VCR. It flashes when all timer
recordings or One Touch Recordings are finished.
13. REC/OTR Button
Press once to start a recording. Press repeatedly to start an
One Touch Recording.
14. REC Light [page 20]
Lights up during recording.
15. PLAY Button(VCR) [page 18]
Press to begin playback.
16. STOP/EJECT Button (VCR) [page 18]
EJECT Button
Press to remove the tape from the DVD/VCR.
STOP Button
Press to stop the tape motion.
17. F.FWD Button (VCR) [page 18]
Press to rapidly advance the tape, or view the picture rapid-
ly in forward during playback. (Forward Search).
18. REW Button (VCR) [page 18]
Press to rewind the tape, or to view the picture rapidly in
reverse during the playback mode (Rewind Search).
19. AUDIO In Jacks
Connect audio cables coming from the audio out jacks of a
camcorder, another VCR, or an audio source here.
20. VIDEO In Jack
Connect a video cable coming from the video out jack of a
camcorder, another VCR, or a video source (laser disc
player, camcorder, etc.) here.
21. SURROUND Button [page 30]
Press to activate the 3D sound.
22.
yy
/I(POWER/STANDBY) Button
Press to turn the power on and off.
(As to the indication of the Operate switch,
“I” shows ON
and “
yy
/I
” shows electrical power stand-by.
)
23. A-B REPEAT Button [page 25]
Repeats playback of a selected section.
24. REPEAT Button [page 25]
Repeats playback of the current disc, title, chapter or track.
25. MODE Button [page 26, 30]
Activates program playback or random playback mode
when playing Audio CD, MP3 or JPEG on discs. Sets
Black level and Slide Show Mode.
H9651UD.qx3 04.3.2 8:54 PM Page 8
–
9
–
EN
1L25
English
26. ZOOM Button [page 24]
Enlarges a part of the DVD-reproduced image.
27. CLEAR/C.RESET Button
● DVD mode [page 24]
Press to reset the setting.
● VCR mode [page 18]
Press to reset the counter. Press to exit from the MENU
screen.
28. ANGLE Button [page 28]
Press to change the camera angle to see the sequence being
played back from a different angle.
29. SUBTITLE Button [page 27]
Press to select the desired subtitle language.
30. TIMER Button [page 20]
Press to put the VCR into standby mode for a timer record-
ing.
30. MENU Button
● DVD mode [page 23]
Press to display the menu of the Disc.
● VCR mode [page 16]
Press to access the VCR menu.
31. Arrow Buttons
● DVD mode
32.
p / o /
B
/
s
Buttons
Move the cursor and determines its position.
● VCR mode
32.
p / o Buttons
Press to enter digits when setting program (For example:
setting clock or timer program). Press to select the setting
modes from the on screen menu.
B Button
When setting program (For example: setting clock or timer
program), press to determine your selection and proceed to
the next step you want to input. Press to determine the set-
ting modes from the on screen menu. Press to add or delete
channel numbers during channel preset.
s Button
Press to cancel a setting of timer program. Press to correct
digits when setting program (For example: setting clock or
timer program). Press to add or delete channel numbers
during channel preset.
32. ENTER Button
Press to accept a setting.
33. RETURN Button
Returns to the previous operation.
34. VCR/TV Button [page 20]
Use to select VCR or TV position.
This DVD/VCR does not have VCR/TV light. If noise
appears on your TV when you turn on DVD/VCR(VCR
mode), press this button.
● VCR Position
To view playback, to monitor video recordings or to
watch TV using the VCR tuner.
● TV Position
To watch TV or to view one program while recording
another.
DISC NAVIGATION Button [page 22]
Press to display the first scene of each chapter of the title
being played.
35. VCR Button [page 12]
Press to select VCR mode for the remote control.
● You can switch the OUTPUT mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However,
if you press
OUTPUT on the front panel first, you need to re-
select the corresponding mode by pressing DVD or
VCR on the remote control.
36.
SLOW Button [page 18]
During tape playback, press to view the video tape in slow
motion. Press PLAY to resume normal playback. This but-
ton does not affect DVD playback.
37. SKIP Buttons
● DVD mode
Press to skip Chapters or Tracks.
38. STOP Button
● DVD mode
Press to stop the disc motion.
● VCR mode
Press to stop the tape motion.
39. h Button
● DVD mode
Press to view the DVD picture in fast reverse motion or
to reverse playback of an Audio CD, MP3 or JPEG on
discs. For DVD, press PAUSE/STEP, then press this but-
ton to begin slow reverse motion playback. Press this
button repeatedly to change the reverse speed of slow
reverse motion.
● VCR mode
Press to rewind the tape, or to view the picture rapidly in
reverse during the playback mode (Rewind Search).
40. PAUSE/STEP Button
● DVD mode [page 23]
Press to pause Disc playback. Press repeatedly to
advance the DVD picture step by step (or one frame at a
time).
● VCR mode [page 18]
While recording, press to temporarily stop the recording
(pause). Press again to resume normal recording. You can-
not pause an One Touch Recording. Press during tape
playback to freeze the picture. Press to advance the pic-
ture one frame at a time during still mode
.
41. D Button
● DVD mode
Press to fast forward the Disc. Press PAUSE/STEP, then
press this button to begin slow motion playback. Press
this button repeatedly to change the forward speed of
slow motion.
● VCR mode
Press to rapidly advance the tape, or view the picture
rapidly in forward during playback (Forward Search).
42. PLAY Button
● DVD mode
Press to begin playback.
● VCR mode
Press to begin playback.
43. CH Button
● VCR mode
Press to change TV channels on the DVD/VCR.
44. REC/OTR Button
Press once to start a recording.
Press repeatedly to start an One Touch Recording.
45. SPEED Button [page 19]
Press to select the VCR’s recording speed (SP or SLP)
46. DVD Button [page 12]
Press to select DVD mode for the remote control.
● You can switch the OUTPUT mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However,
if you press
OUTPUT on the front panel first, you need to re-
select the corresponding mode by pressing DVD or
VCR on the remote control.
47.
SETUP Button [page 29]
Press to enter the setup mode.
48. TOP MENU Button [page 23]
Press to call up the title menu.
49. DISPLAY Button
● DVD mode [page 28]
Press to access or remove the display screen during
DVD, Audio CD, MP3 or JPEG playback.
● VCR mode [page 21]
Press to access or remove the VCR’s on-screen status
display.
50. AUDIO Button [page 27]
Press to select a desired audio language or sound mode.
51. Number Buttons
● DVD mode [page 24]
Press to directly select a Chapter or a Title for play-
back. (DVD)
Press to directly select a Track for playback. (Audio
CD, MP3 or JPEG on discs)
H9651UD.qx3 04.3.2 8:54 PM Page 9
–
10
–
EN
1L25
●VCR mode [page 16]
Press to select TV channels on the DVD/VCR.
To select channels, enter channel numbers as a two-digit
number for the quickest results. For example, to select
channel 6, press 0 then 6.
52. OPEN/CLOSE Button
Press to open or close the disc loading tray.
57. EJECT Button
Press to eject the video cassette from the DVD/VCR.
53. SEARCH MODE Button
● DVD mode [page 24]
Press to access or remove the Search display,
which allows you to go directly to a specific
Title/Chapter/Track/Time/Marker.
● VCR mode [page 18]
Press to perform a Time Search or an Index Search.
Caution: Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent damage
to the DVD/VCR.
Notes
¡To use the remote control to operate the DVD/VCR and its features, press DVD on the remote control before pressing other
DVD’s operation buttons. Verify that the green DVD OUTPUT Light is on.
¡To use the remote control to operate the VCR and its features, press VCR on the remote control before pressing other
VCR’s operation buttons. Verify that the green VCR OUTPUT Light is on.
POWER/STANDBY Button
A-B REPEAT Button
REPEAT Button
MODE Button
SUBTITLE/ TIMER Button
DVD VCRCD
• To turn on and of the
DVD/VCR
ZOOM Button
• To set black level on/off.
• To magnify part of a
picture (x2/x4)
ANGLE Button
AUDIO Button
DISPLAY Button
• Το access various audio
functions on a disc.
• To select STEREO, L-CH
or R-CH
SURROUND Button
OPEN/CLOSE/EJECT Button
SEARCH MODE Button
Tour of the Remote Control
Buttons on remote control work in different ways for DVD, CD and VCR :
Refer to the following table for correct use.
• To turn on and of the
DVD/VCR
• To mark a segment to repeat
between A and B
• To mark a segment to repeat
between A and B
• To repeat play a Chapter
or Title
• To repeat play a Track
or Disc
• To program a specific order
or random playback
• To select camera angles
on a disc
• To select a subtitle on a disc
• To put the VCR into standby
mode for a timer recording
• To display the current
disc mode
• To display the current
disc mode
• To display the current time,
tape counter, channel
• To set virtual surround on/off
• To set virtual surround on/off
• To search chapter or time
• To rapidly return to a location
of disc
• To search the chapter markers
• To search track or time
• To rapidly return to a location
of disc
• To search the track markers
• To call up the index or time
search menu
• To open or close the disc tray • To open or close the disc tray • To eject the video cassette
from the VCR
SUBTITLE
TIMER
ZOOM
DISPLAY
AUDIO
A-B REPEAT
REPEAT
MODE
ANGLE
SURROUND
EJECT
OPEN/CLOSE
NUMBER Buttons
+10
32
98
0
56
1
7
4
• To turn on and of the
DVD/VCR
• To select chapter directly • To select track directly • To select channel.
• The +10 button cannot be
used in VCR mode.
SEARCH MODE
H9651UD.qx3 04.3.2 8:54 PM Page 10
–
11
–
EN
1L25
English
Tour of the Remote Control
• To use the remote control in
DVD mode
ENTER/Arrow Button
(UP/DOWN or LEFT/RIGHT
Button)
SEARCH Buttons
DVD VCRCD
SETUP Button
SKIP Buttons
CH Buttons
• To skip Chapters
STOP Button
PLAY Button
PAUSE/STEP Button
• To skip Tracks
DVD Button
• To select VCR or TV position
• To bring up the DVD Setup
menu
• To bring up the DVD Setup
menu
• To change channels.
• To adjust the tracking manually
during playback
• To search forward/backward
through a disc
• To search forward/backward
through a disc
• To search forward/backward
through a tape
• To stop playback • To stop playback
• To stop playback or record
• To begin disc play • To begin disc play
• To begin tape play
• To advance playback one
frame at a time
• To pause disc play
• To advance playback one
frame at a time
• To pause disc play
• To pause tape play or record
• To use the remote control in
DVD mode
• To select the DVD output mode
• To use the remote control in
DVD mode
• To select the DVD output mode
SETUP
PLAY
SKIP
CH
DVD
STOP
PAUSE/STEP
ENTER
CLEAR/C.RESET Button
MENU Button
TOP MENU Button
RETURN Button
TOP MENU
RETURN
MENU
CLEAR/C. RESET
• To clear the chapter makers.
• To clear the number that is
entered incorrectly
• To clear the track makers
• To remove the most recently
entered program
• To clear the number that is
entered incorrectly
• To exit the VCR menu
• To reset the tape counter
• To bring up the Menu on
a disc
• To call up the VCR menu
• To bring up the DVD's main
menu
• To move the cursor and
determine its position
• To move the cursor and
determine its position
• To select an item on the VCR
menu
• To move to the next VCR
menu
• To go back one step during
clock and timer setting
• To return to a previous menu
•
To view the tape in slow motion
• To select the recording speed
• To start a recording or One
Touch Recording.
VCR Button
SLOW Button
SPEED Button
REC/OTR Button
DISC NAVIGATION Button
VCR/TV Button
VCR
SLOW
SPEED
REC/OTR
VCR/TV
DISC
NAVIGATION
• To display the first scenes of
each chapter of the title being
played
• To select the VCR output mode
• To use the remote control
in VCR mode
H9651UD.qx3 04.3.2 8:54 PM Page 11
–
12
–
EN
1L25
FROM PANEL DISPLAY DISPLAYS DURING OPERATION
LOADING THE BATTERIES
Lights up when the inserted
disc is being played back.
Displays a type of the disc
which is inserted on the tray.
• DVD: DVD disc
• CD: Audio CD, MP3, JPEG
Lights up when the
inserted disc comes
to a pause.
Lights up when the
A-B repeat function
is on.
Lights up when the
repeat function is on.
Lights up when playing back
in slow mode. (DVD)
Displays how long the current title
or track has been played back. When
a chapter or track is switched, the
number of a new title, chapter or
track is displayed.
Lights up when
the ALL repeat
function is on.
GROUP P.SCAN
DVD
CD
Lights up when the
progressive scan
system is activated.
Lights up when the inserted
cassette is being played
back.
Lights up when
the playback is
in still or slow mode.
Lights up during
playback when
the repeat function
is on.
Works as a tape counter(hour,minute,second).
Also displays a channel number,
tape speed, remaining time for OTR or
current time.
VCR REC
PM
Lights up
when a tape is
in the DVD/VCR.
Lights up when
the DVD/VCR is
in VCR position.
This light does not
appear when the
DVD/VCR is in
TV position.
Lights up during a recording.
Flashes when a recording
is paused.
Lights up when
current time is P.M.
Lights up when
the timer recording or an
OTR recording has been set.
No disc inserted or
cannot read the disc
Tray open
Tray closed
Loading the Disc
When a disc is being
Play back
DVD
1. Open the battery compartment
cover.
2. Insert two AA batteries, with each
one oriented correctly.
3. Close the cover.
Notes
¡Do not mix alkaline and manganese batteries.
¡Do not mix old and new batteries.
DVD
VCR
VCR/DVD SWITCHING
Since this product comprises VCR and DVD players, it is necessary to select the correct output mode.
Press VCR on the remote control.
(Verify that the VCR OUTPUT Light is lit.)
SWITCHING TO VCR MODE
Notes
¡Pressing only OUTPUT on the front panel does not
switch the mode of the remote control. You always
need to select the correct mode on the remote con-
trol too.
Press DVD on the remote control.
(Verify that the DVD OUTPUT Light is lit.)
SWITCHING TO DVD MODE
+10
EJECT
32
SEARCH MODE
OPEN/CLOSE
9
ZOOM
DISPLAY
8
AUDIO
0
TOP MENU
SETUP
PLAY
SKIP
CH
56
1
A-B REPEAT
REPEAT
7
CLEAR/C. RESET
SUBTITLE
MODE
ANGLE
DVD
VCR/TV
DISC
NAVIGATION
VCR
SLOW SPEED REC/OTR
RETURN
MENU
STOP
4
SURROUND
PAUSE/STEP
ENTER
TIMER
POWER/STANDBY
LINES
VIDEO IN L [mode] AUDIO IN R
REW F.FWD
STOP/EJECT
PLAY
REC/OTR
RECTIMER
PROGRESSIVE SCAN
DIGITAL AUTO TRACKING
DVD/VCR Combo DV-PF74U
MP3 / JPEG PLAY BACK DVD / CD / CD-R / CD-RW COMPATIBLE
STOP PLAY
OPEN/CLOSE
CHANNEL
VCR
OUTPUT
DVD
VCR
OUTPUT
DVD
OUTPUT button
VCR OUTPUT Light
DVD OUTPUT Light
VCR button
DVD button
H9651UD.qx3 04.3.2 8:54 PM Page 12
–
13
–
EN
1L25
English
DVD/VCR TO TV CONNECTION
1. Disconnect the AC power cord of the TV from the AC outlet.
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of the DVD/VCR.
4. Connect the DVD/VCR to the TV using the RF cable.
5. Plug the AC power cords of the DVD/VCR and TV into the AC outlets.
UHF/VHF
ANT-IN
ANT-OUT
[VHF/UHF
combination antenna]
[Back of the DVD/VCR]
IN
OUT
[Cable box or satellite box]
OR
[Indoor antenna]
[Back of the
UHF/VHF combination TV]
RF cable
(supplied)
From Cable or
Satellite Company
OR
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
HOOKUPS
CAUTION:
¡Be sure to turn off the DVD/VCR and equipment to be connected before connecting.
¡Read through the operation manual for the equipment to be connected.
¡Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.
¡Be sure to keep the DVD/VCR connection cables separate from the TV antenna cable when you install the
DVD/VCR, because it may cause electrical interference when you are watching television programs.
¡DTS audio cannot be produced with an analogue connection.
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD VCR
DVD/VCR
S-VIDEO
OUT
AUDIO OUT
COMPONENT
VIDEO OUT
AUDIO IN
VIDEO OUT
LY
C
B/
PB
CR/
PR
R
L
R
L
R
ANT-IN
ANT-OUT
VIDEO IN
0VM204468
1 2 3 8 9 1154
6 7 10
1. AC Power Cord
Connect to a standard AC outlet to supply power to the
DVD/VCR.
2. COAXIAL Jack (DVD only)
Use coaxial digital audio out to connect to a compat-
ible Dolby Digital receiver. Use to connect to a
Dolby Digital decoder or DTS decoder.
3. DVD AUDIO OUT Jacks (DVD only)
Connect the supplied audio cables here and to the Audio
In jacks of a television or other audio equipment (DVD
only).
4. S-VIDEO OUT Jack (DVD only)
Connect an optional S-Video cable here and to the S-
Video In jack of a television.
5. COMPONENT VIDEO OUT Jacks (DVD only)
Connect optional component video cables here and to
the component Video In jacks of a television.
6. DVD/VCR AUDIO OUT Jacks
Connect the supplied audio cables here and to the Audio
In jacks of a television or other audio equipment.
7. AUDIO IN Jacks (VCR only)
Connect audio cables coming from the audio out jacks
of a camcorder, another VCR, or an audio source here.
8. DVD/VCR VIDEO OUT Jack
Connect the yellow video cable (supplied) here and to
the TV’s Video In jack.
9. VIDEO IN Jack (VCR only)
Connect a cable coming from the video out jack of a
camcorder, another VCR, or an audio-visual source
(laser disc player, video disc player, etc.) here.
10. ANT-IN (Antenna In) Jack
Connect your antenna, RF INPUT Cable Box, or Direct
Broadcast System.
11. ANT-OUT (Antenna Out) Jack
Use the supplied RF coaxial cable to connect this jack
to the ANTENNA IN Jack on your TV.
Notes
¡The S-VIDEO OUT jack, COAXIAL jack and COM-
PONENT VIDEO OUT jack are only useful in DVD
mode.
REAR VIEW
H9651UD.qx3 04.3.2 8:54 PM Page 13
–
14
–
EN
1L25
Notes
¡
When using a AV amplifier with a built in decoder (AV control centre) or Dolby Digital or DTS decoder as shown
in the Method 2, set
“
DOLBY DIGITAL
”
or
“
DTS
”
to
“
BITSTREAM” accordingly for audio output in the setup
mode. (See page 29.) Set “DOLBY DIGITAL”to "PCM" or “DTS” to “OFF” if the decoder is not used. Playing
a DVD using incorrect settings may generate noise distortion, and may also damage the speakers.
¡ The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound
by an MD or DAT deck.
¡
Set “Dolby Digital” to “PCM” and “DTS” to “OFF” for audio output in the setup mode for connecting to an MD
deck or DAT deck. (
See page 29.)
• Method 1 DVD/VCR + Stereo system
• Method 2 DVD/VCR + Dolby Digital decoder or DTS decoder
If your TV does not have A/V terminals:
1. Connect the DVD/VCR to a TV using RF cable (see DVD/VCR TO TV CONNECTION).
2. Select channel 3 on your TV.
3. Insert a pre-recorded tape into the unit.
4. Press OUTPUT on the DVD/VCR.
¡
If VCR OUTPUT light lights up and “VCR” appears on the front panel display. If not, press DVD/VCR on the remote control.
5. Press PLAY.
¡ If noise appears, it means channel 3 is already occupied for broadcasting. In such case, change the RF
output channel of the DVD/VCR to channel 4 with the following steps.
If channel 3 is already occupied for broadcasting,
1. Press PLAY once.
2. After a few seconds, press PLAY button on the DVD/VCR for 3 seconds.
¡ The RF output channel will be changed to channel 4 and you will see a playback picture. “ch4” appears
in the front panel display.
¡ If a picture does not appear, repeat these steps.
¡ If there is a power failure or the DVD/VCR is unplugged for more than 30 seconds, the RF output chan-
nel setting will return to channel 3.
RF OUTPUT CHANNEL
Stereo system
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
L
Y
C
B
/
P
B
C
R
/
P
R
R
COAXIAL
AUDIO
DVD/VCR
Method 1
(Analog)
AUDIO OUT
DIGITAL
AUDIO OUT
Method 2
Dolby Digital decoder,
DTS decoder, MD deck
or DAT deck
CONNECTION TO AN AUDIO SYSTEM
H9651UD.qx3 04.3.2 8:54 PM Page 14
–
15
–
EN
1L25
English
CONNECTION TO A TV (FOR VIDEO)
• Method 1 DVD/VCR + TV with Video Input Jack
•
Method 2 DVD/VCR + TV with S-Video Input Jack
• Method 3 DVD/VCR + TV with Component Video Jacks
Notes
¡Connect the DVD/VCR directly to a TV. If the A/V cables are connected to a VCR, pictures may be
distorted due to the copy protection system.
¡
The COAXIAL,
DVD AUDIO OUT,
S-VIDEO OUT, and COMPONENT VIDEO OUT jacks are only useful in
DVD mode.
DIGITAL
AUDIO OUT
COAXIAL
ANT-OUT
ANT-IN
AUDIO
OUT
DVD VCR
DVD/VCR
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
L
LY
C
B/
P
B
C
R/
P
R
L
RR
R
AUDIO IN
LR
VCRDVD/VCR
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
L
L
R
R
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
S-VIDEO
OUT
COMPONEN
VIDEO OUT
L
R
or
VIDEO IN
VCRDVD/VCR
AUDIO IN
VIDEO IN
AUDIO OUT
VIDEO OUT
L
L
R
R
S-VIDEO IN
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
L
R
Y
C
B/
P
B
C
R/
P
R
DIGITAL
AUDIO OUT
CB
Y
C
R
COMPONENT
VIDEO IN
or
COAXIAL
AUDIO
OUT
DVD
S-VIDEO
OUT
COMPONENT
VIDEO OUT
L
R
Y
C
B/
P
B
C
R/
P
R
PB
Y
P
R
(Analog) AUDIO OUT
VIDEO OUT
TV
Method 1
Good pictureBasic Audio
Method 2 Method 3
Better picture Best picture
S-VIDEO OUT
COMPONENT VIDEO OUT
Video
cable
(supplied)
Audio cable
(supplied)
S-Video
cable
(commercially
available)
Component
Video cables
(commercially
available)
DVD/VCR
H9651UD.qx3 04.3.2 8:54 PM Page 15
–
16
–
EN
1L25
6 After scanning, the tuner stops on the low-
est memorized channel. The TV screen
returns to TV mode.
¡If “AUTO SET UP” appears on the TV screen again,
check the cable connections. Press B once again and
the DVD/VCR will begin preset again.
AUTOMATIC CHANNEL SET UP
SETUP
You can automatically program the tuner to scan only
the channels you receive in your area.
¡Channel memory programming is NOT needed when
you connect the DVD/VCR to a cable box or a satel-
lite box as in "DVD/VCR TO TV CONNECTION"
on page 14. In this case, select channel 3 on your TV.
Then, the channel you want to record or view may be
selected at the cable box or satellite box.
¡If noise appears, change the RF output channel of
the DVD/VCR to channel 4 by pressing PLAY for
3 seconds during playback. Then select the same
channel (CH4) on your TV.
¡Follow the steps below once. Repeat only if there is
a power failure or if the DVD/VCR is unplugged for
more than 30 seconds. (In these cases, the pro-
grammed channels are erased.)
¡You must follow the steps below before attempting
to play or record a video tape. If you want to play
or record a video tape BEFORE programming the
tuner, you can cancel it by pressing
CLEAR/C.RESET.
1 You need to connect the antenna or cable to
the DVD/VCR first. Then, connect the
DVD/VCR power plug to a standard AC outlet.
2 Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV. (See “RF Output Channel”
on page 14 for more details.)
3 Turn on the DVD/VCR by pressing y/I.
4 Select the On Screen Language (“ENG-
LISH”, “FRANCAIS” or
“ESPAÑOL”) by pressing
K
or L. Then, press B.
5 Begin channel preset by pressing B once.
The tuner scans and memo-
rizes all active channels in
your area.
¡The DVD/VCR distinguishes
between standard TV channels
and cable channels.
VCR
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using CH (o/p)
or by directly entering channel numbers using the
Number buttons.
Note for using the Number buttons:
¡When selecting cable channels which are higher
than 99, enter channel numbers as a three-digit num-
ber.(For example: 117, press 1,1,7)
¡You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
TO PRESET THE CHANNELS AGAIN
1 Press MENU until the main menu appears.
2 Select “CHANNEL SET UP” by pressing K
or L. Then, press B.
3 Select “AUTO SET UP” by pressing K or L.
Then, press
B.
¡After scanning, the tuner stops on the lowest memo-
rized channel.
LANGUAGE SELECT
ENGLISH [ON]
FRANCAIS
ESPAÑOL
AUTO SET UP
CH 01
H9651UD.qx3 04.3.2 8:54 PM Page 16
–
17
–
EN
1L25
English
Español
CLOCK SET UP
1 Select main menu by pressing MENU.
¡If the clock is not set, the CLOCK SET menu
appears first. In this case, follow step [3].
2 Select "CLOCK SET" by pressing K or L.
Then, press
B.
3 Set the clock.
¡To go back one step, press s.
4 Start the clock by pressing
CLEAR/C.RESET or
B.
VCR
CLOCK SET
MONTH DAY YEAR
03 / 17 WED 2004
HOUR MINUTE AM/PM
05 : 40 PM AM
PM
1) Set the month
Press K or L repeatedly.
Then, press B.
2) Set the day
Press K or L repeatedly.
Then, press B.
3) Set the year
Press K or L repeatedly.
Then, press B.
The day of the week will appear automatically.
4) Set the hour
Press K or L repeatedly.
Then, press B.
5) Set the minute
Press K or L repeatedly.
Then, press B.
6) Set AM or PM
Press K or L repeatedly.
TO CHANGE THE ON-SCREEN
LANGUAGE
1 Press MENU repeatedly until the main
menu appears.
2 Select "LANGUAGE SELECT" by pressing K
or L. Then, press B.
3 Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing
K or L. Then, press
CLEAR/C.RESET.
¡If you accidentally select Spanish or French and
need English: Press MENU and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press B,
and select ENGLISH by pressing K or L. Finally,
press CLEAR/C.RESET.
VCR
TO ADD/DELETE CHANNELS
When scanning, some channels may be skipped due to
a weak signal. In such cases, you can add the channels
to the DVD/VCR memory manually.
1 Press MENU until the main menu appears.
2 Select "CHANNEL SET UP" by pressing K
or L. Then, press B.
3 Select "MANUAL SET UP" by pressing K or
L. Then, press B.
4 Enter the desired channel number by press-
ing
K or L.
5 Add or Delete it from memory by pressing
B or s so that "ADD" or "DELETE" flashes
on the TV screen accordingly.
6 Exit the Preset mode by pressing
CLEAR/C.RESET.
- MENU -
TIMER PROGRAMMING
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
SAP
[OFF]
[ON]
H9651UD.qx3 04.3.2 8:54 PM Page 17
–
18
–
EN
1L25
PICTURE SEARCH
If you want to skip or repeat a scene during playback,
press D or E.
¡Press it again and the DVD/VCR will now search at
super high speed. (in the LP/SLP modes only).
INDEX SEARCH
An index mark will be assigned at the beginning of each
recording you make. You may skip to a specific marked
point by following the steps below.
1 Press SEARCH MODE so that the Index
Search menu appears.
2 Enter the number of recordings you wish to
skip by pressing
K or L
within 30 seconds.
3 Press B or { to start index search.
¡If you want to go in the forward direction, press B.
If you want to go in the reverse direction, press {.
¡If you want to stop search function, press STOP.
¡After index search, the DVD/VCR will play the tape
automatically.
TIME SEARCH
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
1 Press SEARCH MODE so that the Time
Search menu appears.
2 Enter your desired time to
skip by pressing
K or L
within 30 seconds.
3 Press B or { to start time search.
¡If you want to go in the forward direction, press B.
¡If you want to go in the reverse direction, press {.
¡If you want to stop search function, press STOP.
¡After time search, the DVD/VCR will play the tape
automatically.
VCR
PLAYBACK FUNCTION
NORMAL PLAYBACK
1 Insert a prerecorded tape. The DVD/VCR will
turn on.
¡If the safety tab has been removed, the
DVD/VCR will start playback automatically.
¡If a cassette is in DVD/VCR, STOP sym-
bol appears in TV screen when turning on the
DVD/VCR(VCR mode), and “ ” appears in the
front panel display.
2 Turn on the TV and set the TV to channel 3.
¡
If noise appears, change the RF output channel of the
DVD/VCR to channel 4 by pressing PLAY for 3 seconds
during playback. Then select the same channel (CH4) on
your TV. (See “RF Output Channel” on page 14 for more
details.)
¡If you connect a TV to the DVD/VCR using AV
cable, set the TV to channel AUX. (VIDEO)
3 Begin playback by pressing PLAY.
¡Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press SKIP/CH on
the remote or CHANNEL (o/p) on the DVD/VCR.
¡
When a tape has reached the end, the DVD/VCR will rewind
the tape to the beginning and eject the tape automatically.
4 To stop playback, press STOP.
¡If no corresponding symbols appear on the display
when you press buttons such as PLAY, REC/OTR,
D or E, that means no cassette tape is in the
DVD/VCR. Please insert a tape.
VCR
STILL/SLOW
You can freeze the picture on TV screen by pressing
PAUSE/STEP during playback.
¡You can advance the picture one frame at a time by
pressing PAUSE/STEP during the Still mode.
¡You cannot manually adjust the tracking of a still pic-
ture. However, if the picture begins to vibrate vertical-
ly during the still mode, you can stabilize the picture by
pressing CH (
o/p).
¡If the picture is distorted or rolling vertically, adjust the
vertical hold control on your TV, if so equipped.
¡You can watch in the slow motion by pressing SLOW
during playback or the still mode.
¡If a noise bar appears on the TV screen, you can reduce
it by pressing CH (
o/p).
¡After the DVD/VCR has been in Still/Slow mode for 5
minutes, it will stop automatically to protect the tape
and the video head from damage.
¡To return to playback, press PLAY.
AUTO REPEAT PLAYBACK
This feature allows you to play a tape over and over.
1 Select main menu by pressing MENU.
2 Select "AUTO REPEAT" by pressing K or L.
3 Begin auto repeat playback by pressing B
so that ON appears next to "AUTO REPEAT".
¡If the on-screen menu still remains, press
CLEAR/C.RESET to exit the menu.
¡To cancel the Auto repeat mode, press B at step [3]
so that OFF appears next to "AUTO REPEAT".
VCR
SEARCH FUNCTIONS
TIME SEARCH
2 : 50
INDEX SEARCH
03
Counter Reset
¡You can reset the counter by pressing
CLEAR/C.RESET on the remote control.
H9651UD.qx3 04.3.2 8:54 PM Page 18
–
19
–
EN
1L25
English
RECORDING FUNCTION
It may be UNLAWFUL to record copyrighted material with-
out the consent of the copyright owner.
Accidental Erasure Prevention
To prevent accidental recording on a recorded
cassette, remove its record safety tab. To record
on it later, cover the hole with cellophane tape.
Before recording, make sure:
¡The desired channel is selected by
pressing the Number buttons on the remote control or
CHANNEL (o/p). (If you connected the DVD/VCR
to a cable box or satellite box as in "DVD/VCR TO
TV CONNECTION" on page 13, select channel 3 on
your TV. Then, select the channel you want to record
with the cable box or satellite box. In this case, you can
ONLY record and view the SAME channel.)
¡If noise appears, change the RF output channel of
the DVD/VCR to channel 4 by pressing PLAY for
3 seconds during playback. Then select the same
channel (CH4) on your TV.
¡There is a tape with a safety tab in the DVD/VCR.
¡The desired recording speed is selected in SP (stan-
dard play) or SLP (super long play) mode by press-
ing SPEED on the remote control.
¡TV STEREO or SAP is selected.
VCR
Type of tape T60 T120 T160
SP mode 1 hour 2 hours 2-2/3 hours
SLP mode 3 hours 6 hours 8 hours
Tape Speed Recording/Playback Time
1 Begin the recording by pressing REC/OTR.
The REC Light lights up and “REC” appears
in the front panel display.
¡To temporarily stop recording or to resume it, press
PAUSE/STEP. After the DVD/VCR has been in
Pause mode for 5 minutes, it will stop automatically
to protect the tape and the video head from damage.
2 Press STOP when the recording is completed.
Note
¡While you are recording on the DVD/VCR, press the
VCR/TV button so that the “VCR” in the display
panel disappears on the DVD/VCR.
VCR
OTR (One Touch Recording)
This feature allows you to set the recording length sim-
ply by pressing REC/OTR.
3 Press REC/OTR to begin OTR. “REC” and
“”appear in the front panel display.
Change the recording length by pressing
REC/OTR repeatedly.
VCR
¡If a tape ends during OTR, the DVD/VCR will stop,
eject the tape, and switch to the DVD mode automati-
cally as the TIMER light blinks. (If the DVD power is
off, the VCR will go into the STANDBY mode).
¡When OTR is finished , the VCR turns off automat-
ically. To use the VCR again, press TIMER on the
remote, or STOP/EJECT on the DVD/VCR.
TIMER RECORDING
You may set the DVD/VCR to start recording while
you are away. You can set eight programs to record on
specific days, daily or weekly within 1 year period.
If you have not yet set the clock, "CLOCK SET"
appears. If so, follow the steps [3] and [4] in "CLOCK
SET" section on page 18. Then, set the timer record-
ing.
1 Insert a tape with its safety tab into the
DVD/VCR.
2 Select main menu by pressing MENU.
3 Select "TIMER PROGRAMMING" by press-
ing
K or L. Then, press B.
The set up screen is dis-
played.
4 Set the timer.
¡To go back one step, press s.
VCR
PROGRAM NUMBER 4
ONCE
DAILY
WEEKLY
PROGRAM NUMBER 4
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
PROGRAM NUMBER 4
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
ONE TIME PROGRAM
1) Set the program number (1-8)
Program number which is not set up
flashes. Press K or L repeatedly
for the desired program number.
Then, press B.
2) Set the frequency of the recording
For once: Press K or L to point to
"ONCE".
For daily (Monday~Friday): Press K
or L to point to "DAILY".
For weekly: Press K or L to point
to "WEEKLY".
Then, press B.
3) Set the date
First, press K or L for the month.
Then, press B. Next, press K or
L for the day. Then, press B.
Record safety tab
PROG 12345678
DATE -
START TIME
END TIME
CHANNEL
REC SPEED
TIMER PROGRAMMING
REC OTR(0:30) OTR(1:00).....
(Normal recording)
OTR(8:00) OTR(7:30)
NORMAL RECORDING
H9651UD.qx3 04.3.2 8:54 PM Page 19
–
20
–
EN
1L25
HINTS FOR TIMER
RECORDING
¡If there is a power failure or the DVD/VCR is
unplugged for more than 30 seconds, the clock set-
ting and all timer settings will be lost.
¡If a tape ends during timer recording, the DVD/VCR
will stop, eject the tape, and switch to the DVD
mode automatically as the TIMER light lights up on
the DVD/VCR and “REC” and “ ” in the front
panel display flash. (If the DVD is not in use, the
VCR will be on STANDBY mode).
¡
If a tape is not in the
DVD/VCR
or does not have a
safety tab, the TIMER light flashes and timer recording
will not operate. Please insert a recordable
tape.
¡
When all timer recordings are finished, the TIMER light
will flash. To use the DVD/VCR again as usual, press
TIMER to disable the flashing TIMER light, “REC”,
and “ ”, then press VCR/TV to select the VCR posi-
tion. Select either VCR or DVD mode, then continue
with the other features as described in this manual.
VCR
¡When timer recordings are set, the TIMER light will
light up, and “REC” and “ ” will appear in the
front panel display. To use the DVD/VCR as usual
until the time of the recording, press TIMER so that
the TIMER light turns off and “REC” and “ ” dis-
appear. Press VCR/TV to choose the VCR position.
Select either VCR or DVD mode, then continue with
the other features as described in this manual.
If you want to use the DVD player during a
timer recording or while the TIMER light,
“REC” and “ ” are on or flash.
¡
You can use the DVD player while the TIMER light,
“REC” and “
”
are on or flashes, or during a timer
recording. Press y/I to turn on the DVD/VCR.
Press DVD on the remote control to choose DVD
mode, then continue with the other DVD features as
described in this manual. You don’t have to set the .
TIMER off to use the DVD only.
PROGRAM NUMBER 4
DATE 05 /12 WED
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05 /12 WED
START TIME 07: 30 PM
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05 /12 WED
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL - -
REC SPEED - -
ONE TIME PROGRAM
Press K or L repeatedly for the
desired channel number. Then,
press B.
PROGRAM NUMBER 4
DATE 05 /12 WED
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL
16
REC SPEED SP
SP
SLP
ONE TIME PROGRAM
4) Set the start time
First, press K or L for the hour.
Then, press B. Next, press K or L
for the minute. Then, press B. And
then, press K or L for AM or PM. Then, press B.
5) Set the end time
Follow the instructions of
"Set the start time" to set
the end time.
7) Set the tape speed
Press K or L repeatedly for the
desired tape speed. Then, press B.
6) Set the channel number
If you connected the DVD/VCR to a cable box or satellite box
as in "DVD/VCR TO TV CONNECTION" on page 14, select
the DVD/VCR to channel 3 or 4 the same channel as RF
output channel of the DVD/VCR. Then, select the channel you
want to record on the cable box or satellite box.
Leave the cable box or satellite box on for timer recording.
5 To set another program, repeat step [4]. To
exit, press CLEAR/C.RESET.
6 Press TIMER to set the timer.
¡The TIMER light on the DVD/VCR lights up, and
“REC” and “ ” appear in the front panel display.
TIMER RECORDING WILL NOT BE ACTIVAT-
ED UNLESS YOU PRESS TIMER.
TO STOP AN AUTOMATIC TIMER PRO-
GRAM ALREADY STARTED
Press STOP/EJECT on the DVD /VCR.
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
1 Press TIMER.
¡If the power of the DVD/VCR is off, press y/I
instead of TIMER, then go on to the next step.
¡If the DVD output mode is selected, you have to
switch it to the VCR mode by pressing the VCR on the
remote control or the OUTPUT on the DVD/VCR.
2 Select main menu by pressing MENU.
3 Select "TIMER PROGRAMMING" by press-
ing
K or L. Then, press B.
4 Select the program number you want to
check by pressing
K or L.
¡The details of the selected program appears on the
TV screen.
¡Go to the digit you want to change by pressing B or
s. Then, enter correct numbers by pressing o or p.
¡You may cancel the entire program by pressing s
while the program number flashes.
5 Press CLEAR/C.RESET to exit.
6 Press TIMER to return to timer stand-by
mode.
H9651UD.qx3 04.3.2 9:33 PM Page 20
–
21
–
EN
1L25
English
COPYING A VIDEO TAPE
SPECIAL FEATURES
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning:
Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording DVD/VCR (this unit), the play-
ing VCR (another source) and your TV using the fol-
lowing diagram.
¡You can use the AUDIO/VIDEO input jacks on the
front panel of the DVD/VCR instead of using the
jacks on the back.
VCR
[Playing VCR]
(another source)
IN
LEFT
RIGHT
OUT
AUDIO
VIDEO
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD VCR
DVD/VCR
S-VIDEO
OUT
AUDIO OUT
COMPONENT
VIDEO OUT
AUDIO IN
VIDEO OUT
LY
C
B/
PB
CR/
PR
R
L
R
L
R
ANT-IN
ANT-OUT
VIDEO IN
0VM204468
Audio/Video cables
(not supplied)
[Recording DVD/VCR]
(this unit)
ANT in
[TV set]
(Use for monitoring)
RF cable
(supplied)
MTS (Multi-Channel Television
Sound) SYSTEM
When you play a VHS tape, or receive a broadcast on
the DVD/VCR tuner channel
you are watching, the current
status will appear when you
press DISPLAY on the remote
control. When you record a
MTS broadcast signal, you need
to set it to MTS mode.
1)* Press MENU and select "TV STEREO" or
"SAP" by pressing
K or L. Then, press B.
To exit, press CLEAR/C.RESET.
¡Although a program may be broadcast in both stereo
and sub audio, you must select the Recording mode
to TV STEREO or SAP before you record a broad-
cast.
2)* Press MENU and select "AUDIO OUT" by
pressing
K or L. Then, press B.Next,
select "HIFI" or "MONO" by pressing
K or
L.To exit, press CLEAR/C.RESET.
¡While the DVD/VCR is set in HIFI stereo mode,
HIFI appears on the TV screen. While the DVD/
VCR is set in monaural (MONO) mode, HIFI disap-
pears from the TV screen.
VCR
MTS RECORDING/MONITOR MODE
Type of
broadcast
Hi-Fi audio track
(2-channel)
Normal audio
track
Regular
(
monaural
audio)
-None-
Mono
Stereo
broadcast
STEREO L+R
Bilingual
broadcast
SAP
Main audio
program
Sub audio
program
Stereo &
Bilingual
broadcast
STEREO
SAP
L+R
I
STEREO/SAP
Selection
-Invalid-
- nvalid-
TV STEREO*
SAP*
TV STEREO*
SAP*
L-channel
Mono
L
Main audio
program
Sub audio
program
L
Sub audio
program
R-channel
Mono
R
Main audio
program
Sub audio
program
R
Sub audio
program
Sub audio
program
*
Display on the
TV screen
STOP 12:00AM
CH 32
STEREO
SAP
SP 0:00:00 HIFI
1)*
2)*
1 Insert a pre-recorded tape into the playing
VCR.
2 Insert a tape with a safety tab into the
recording DVD/VCR.
3 Press SPEED on the recording DVD/VCR to
select the desired recording speed
(SP/SLP).
4 Select the “L1” or “L2”position on the
recording DVD/VCR by pressing the CHAN-
NEL (
K/L ).
¡
When you use the A/V input jacks on the back of the
DVD/VCR, select "L1" position by pressing [0], [0],
[1] or the CHANNEL(o/p) on the DVD/VCR.
¡
When you use the A/V input jacks on the front of the
DVD/VCR, select "L2" position by pressing [0], [0],
[2] or the CHANNEL(o/p) on the DVD/VCR.
Note
“L1” and “L2” are found before the lowest memo-
rized channel. (Example: CH2)
5 Press REC/OTR on the recording DVD/VCR.
6 Begin playback of the tape in the playing
VCR.
¡For best results during dubbing, use the DVD/VCR’s
front panel controls whenever possible. The remote
control might affect the playing VCR’s operation.
TO MONITOR THE RECORDING
1 Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the DVD/VCR to channel 4 by pressing PLAY for 3
seconds during playback. Then select the same
channel (CH4) on your TV. (See “RF Output
Channel” on page 14 for more details).
2 Press VCR/TV on the remote control of the
recording DVD/VCR.
¡Always use video-quality shielded cables with
RCA-type connectors. Standard audio cables are not
recommended.
¡You can use a video disc player, satellite receiver,
camcorder or other audio/video component with
A/V outputs in place of the playing VCR.
H9651UD.qx3 04.3.2 8:54 PM Page 21
–
22
–
EN
1L25
BASIC PLAYBACK
Getting started
¡Turn on the power of the TV, amplifier and any other
components which are connected to the DVD/VCR.
¡Make sure the TV and audio receiver (commercially
available) are set to the correct channel.
¡Select DVD mode by pressing DVD on the remote
control or output on the front panel. The DVD OUT-
PUT light lights up.
1 Press y/I.
¡“Load” will appear briefly in the front panel display.
¡Check that the DVD OUTPUT Light is lit. If not,
press DVD on the Remote control to switch to DVD
mode.
2 Press OPEN/CLOSE to open disc loading
tray.
3 Place the chosen disc in the tray, with the
label facing up.
JPEG
MP3
CD
DVD
PLAYING A DISC
AUTO REWIND
When a tape reaches the end during recording, play-
back, or fast-forward, the tape will automatically
rewind to the beginning. After rewinding finishes, the
DVD/VCR will eject the tape and switch itself off.
¡The DVD/VCR will not rewind the tape automati-
cally during timer recording or One Touch
Recording.
REAL TIME TAPE COUNTER
¡ The elapsed recording or play time (in hours, min-
utes, and seconds) will be displayed on the TV dis-
play. No time is displayed when playing back the
blank portion of the cassette.
4 Press PLAY.
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
PLAY.
¡When you playback the DVD with a title menu, it
may appear on the screen. In this case, refer to
“TITLE MENU” on page 23.
5 Press STOP to stop playback.
Notes
¡A prohibited icon “ ” may appear at the top-right
on the TV screen during operation, warning that a
prohibited operation has been encountered by the
DVD/VCR or the disc.
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title, or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
GENERAL FEATURES
DVD may contain menus to navigate the disc and access
special features. Press appropriate Number button or use
Arrow (L/K/B/s) to highlight your selection in the
DVD main menu and press ENTER to confirm.
Note
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
DVD
DISC NAVIGATION
1 Press DISC NAVIGATION.
DURING TITLE PLAYBACK OR WHEN RESUME IS ON:
¡A shot from each chapter including the one current-
ly being played will be displayed on the screen.
¡
The chapter currently being played is selected in yellow.
IN STOP MODE (RESUME OFF):
¡The first scene of each chapter of the first title will
be displayed.
2 Press Arrow (K/L/s/B) to select your
desired chapter.
¡Up to 6 chapters can be displayed at one time. If
the title has more than 6 chapters, press SKIP G
to go to the next page. Press SKIP H to go back
to the previous page.
¡You can change the title by moving up to the field
where the title number is shown with Arrow (K),
and entering a title number of your choice.
3 Press ENTER or PLAY.
¡Playback of the selected chapter will start.
Notes
¡Pressing DISC NAVIGATION before pressing ENTER or
PLAY at step 3 will cease the DISC NAVIGATION func-
tion, and the playback will be stopped. The resume infor-
mation will be lost.
¡When a disc menu is shown, the DISC NAVIGATION fea-
ture does not function.
¡DISC NAVIGATION takes a few seconds to respond.
¡With some discs, part of the DISC NAVIGATION screen
may not be displayed properly. This is not a malfunction.
¡Some discs do not support DISC NAVIGATION feature.
¡While the DISC NAVIGATION is on the screen, the
sound is muted.
¡It takes about 15 seconds to display 6 shots.
DVD
¡
If a disc is dirty or has scratches, the pictures may
appear distorted and the playback operation may stop.
In such cases, clean the disc and unplug the power cord
and then plug it again before resuming playback.
H9651UD.qx3 04.3.2 8:54 PM Page 22
–
23
–
EN
1L25
English
TITLE MENU
1 Press TOP MENU.
¡The title menu will appear.
2 If the feature is not available, symbol
may appear on the TV screen.
3 Press Arrow (L/K/B/s) to select an item,
and ENTER to confirm selection.
DVD
STEP BY STEP PLAYBACK
1 During playback, press PAUSE/STEP.
¡Playback will pause and sound will be muted.
2 The disc goes forward by one frame each
time PAUSE/STEP is pressed.
3 To exit step by step playback, press PLAY.
Note
¡Set STILL MODE to FIELD on the display menu if
pictures during step by step playback are blurred.
(Refer to page 30.)
DVD
RESUME
1 During playback, press STOP.
¡Resume message will appear on the TV screen.
2 Press PLAY, playback will resume from the
point at which playback was stopped.
¡To cancel resume, press STOP twice.
Notes
¡The resume information stays on even when the
power is turned off.
¡For MP3 and JPEG, playback will resume from the
beginning of the track at which playback was
stopped
.
JPEGMP3
CD
DVD
DISC MENU
1 Press MENU.
¡The DVD main menu will appear.
2 If the feature is not available, symbol
may appear on the TV screen.
3 If disc menu is available on the disc, audio
language, subtitle options, chapters for the
title and other options will appear for selec-
tion.
4 Press Arrow (L/K/B/s) to select an item,
and ENTER to confirm selection.
DVD
CALLING UP A MENU SCREEN
DURING PLAYBACK
¡Press MENU to call up the DVD menu.
¡Press TOP MENU to call up the title menu.
Note
¡Contents of menus and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
1 During playback, press g or h repeat-
edly to select the required forward or
reverse speed.
¡For DVDs, fast forward or reverse search speed is
different depending on the disc. Approximate speed
is 1(x2),2(x8),3(x50),4(x100).
¡For Audio CDs, the approximate speed is x16.
¡For MP3, the approximate speed is x8.
2 To return to normal playback, press PLAY.
MP3
CD
DVD
FAST FORWARD/REVERSE
SEARCH
PAUSE
1 During playback, press PAUSE/STEP.
¡Playback will pause and sound will be muted.
2 To continue playback, press PLAY.
Note
¡Set STILL MODE to FIELD on the display menu if
pictures in the pause mode are blurred. (Refer to
page 30.)
JPEGMP3
CD
DVD
H9651UD.qx3 04.3.2 8:54 PM Page 23
–
24
–
EN
1L25
TRACK SEARCH
There are three ways to begin playback on an Audio
CD, MP3 or JPEG disc at a specific Track.
Using the Number buttons
1 Press the Number buttons to enter the
desired Track number.
¡Playback will start at the selected track.
JPEGMP3
CD
ZOOM
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
1 Press ZOOM during playback.
¡Playback will continue.
2 Press ZOOM repeatedly to select the
required zoom factor: x2, x4 or OFF.
3 Use the Arrow (K/L/s / B) to move the
zoomed picture across the screen.
4 To exit zoom mode, press ZOOM.
Notes
¡Zooming function does not work while disc menu is
shown.
¡x4 zoom is not available on some discs.
¡Only x2 zoom is available on JPEG.
JPEGDVD
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡To play track 26, press +10, 2, 6 on the Number but-
tons.
Using SEARCH MODE
1 Press SEARCH MODE.
¡The track search display appears.
2 Within 30 seconds, select a desired track
number using the Number buttons.
¡For single digits press 0 first if the total tracks on the
disc are 10 or more.
¡Playback will start at the selected track.
¡Press CLEAR/C.RESET to erase the incorrect input.
Using SKIP
H
,
G
¡During playback, press SKIP G to move the next
track. Press it repeatedly to skip subsequent tracks.
Press SKIP H to go back to beginning of the current
track. Press it repeatedly to go to the previous tracks.
¡Track number will appear briefly in the front display
panel.
¡If SKIP HGis pressed while the playback is
paused, the playback will be paused again after skip-
ping to the next track.
Note
¡SKIP HG are not available when playback is
stopped.
TITLE / CHAPTER SEARCH
1 During playback, press SEARCH MODE
repeatedly until you see the Title or Chapter
search screen.
2 Enter the desired chapter/title number using
the Number buttons.
¡Playback will start at the selected Chapter or Title.
¡Press CLEAR/C.RESET to erase the incorrect input.
¡For single digits, press 0 first if the total tracks on
the disc are 10 or more.
DVD
_/2
TIME SEARCH
1
During playback, press SEARCH MODE repeat-
edly until the Time Search screen appears.
2 Within 30 seconds, enter a desired disc
time using the Number buttons.
¡Playback will start at the specified time.
¡Press CLEAR/C.RESET to erase the incorrect input.
Note
¡When there is no need to enter a number, “0”
appears automatically. For example, “0:0_:_ _”
appears in the Time Search display if the total time
of the disc is less than 10 minutes.
CD
DVD
SLOW FORWARD /
SLOW REVERSE
1 During playback, press PAUSE/STEP.
2 Press g or h .
¡ Slow motion playback will begin and sound will be
muted.
3 Press g or h .
¡ Slow forward or reverse speed is different depend-
ing on the disc. Approximate speed is
1(1/16),2(1/8),3(1/2).
4 To return to normal playback, press PLAY.
Note
¡
Set STILL MODE to FIELD on the Display menu if pictures
in the slow playback mode are blurred. (refer to page 30)
DVD
H9651UD.qx3 04.3.2 8:54 PM Page 24
–
25
–
EN
1L25
English
REPEAT TRACK
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
CD
TRACK ALL OFF
(current track repeat) (entire disc repeat)
(repeat
off)
Notes
¡Track repeat setting will be cleared by moving to
other track.
¡Repeat playback does not function during A-B
REPEAT playback.
A-B REPEAT
1 Press A-B REPEAT at your chosen starting
point.
¡ A- appears briefly on the TV screen.
2 Press A-B REPEAT again at your chosen
end point.
¡ A-B appears briefly on the TV screen, and the
repeat sequence begins.
3 To exit the sequence, press A-B REPEAT.
Notes
¡The A-B REPEAT section can only be set within the
current title (for DVDs), or current track (for audio
CDs).
¡A-B REPEAT is not available with some scenes on
some DVDs.
¡To cancel the A point which was set, press
CLEAR/C.RESET.
¡A-B REPEAT playback does not function during
title, chapter, track or all repeat playback.
CD
DVD
MARKER SETUP SCREEN
Use markers to memorize your favorite places on a
disc.
1 Press SEARCH MODE repeatedly until
Markers appear on the TV screen.
2 Press Arrow (s / B) to select 1, 2, 3, 4, 5, 6,
7, 8, 9, or 10 and ensure that “- : - - : - -”
appears in the display.
3 When you reach the desired point, press
ENTER.
¡The Title or Track and elapsed playing time will
appear in the TV screen.
4 To return to the Marker later, press SEARCH
MODE repeatedly during playback until
Makers appears. Use Arrow (
s/ B) to
choose the desired marker, then press
ENTER.
Notes
¡Opening the tray, turning off the power, or selecting
AC (ALL CLEAR) then pressing ENTER will erase
all Markers.
¡To clear a marker, using Arrow (s/ B
)
, position the
cursor on to the marker number to be cleared and
press CLEAR/C.RESET.
¡You can mark up to 10 points.
5 Press SEARCH MODE or RETURN to exit.
CD
DVD
REPEAT
REPEAT TITLE / CHAPTER
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
DVD
REPEAT is available only during playback.
CHAPTER TITLE OFF
(current chapter repeat) (current title repeat)
(repeat
off)
Notes
¡Track Repeat Title/Chapter is not available on some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
JPEGMP3
TRACK GROUP OFF
(current track
repeat)
(current folder
repeat)
(repeat
off)
ALL
(entire disc
repeat)
H9651UD.qx3 04.3.2 8:54 PM Page 25
–
26
–
EN
1L25
RANDOM PLAYBACK (CD)
SLIDE SHOW MODE
This shuffles the play order of tracks instead of play-
back of the original sequence.
1 In stop mode, press MODE repeatedly until
the RANDOM
screen appears.
2 Press PLAY to start random playback.
Note
¡To repeat the current track in the random selection,
press REPEAT repeatedly until TRACK appears
during playback. To repeat the entire random selec-
tion press REPEAT repeatedly until ALL appears
during playback.
CD
PLAY
CD-DA TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
RANDOM
Insert an MP3 or JPEG disc, then press MENU to call
up the MP3 menu on the TV screen.
1 In stop mode, press Arrow (K/L) to select
the desired group track.
¡If a group is selected,
press
B
or ENTER to go
on to the track selection
screen. Press Arrow (K/L)
to choose a track, then
press
B
or ENTER.
¡If a track is selected,
press PLAY or ENTER to start playing tracks.
Starting from the one you’ve just chosen the subse-
quent tracks will be played.
¡Press TOP MENU to return to the first item.
2 Press STOP to stop playback.
Notes
¡Folders are known as Groups; files are known as
Tracks.
¡Folders are accompanied by icon.
¡MP3 files are accompanied by icon.
¡JPEG files are accompanied by icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 512 files can be recognized.
¡Up to 8 hierarchies can be created.
This DVD/VCR recommends the use of files record-
ed at the below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
JPEG
MP3
MP3 / JPEG PLAYBACK
PLAY
ENTER
FILE LIST
FOLDER
MP3
JPEG
DISC NAME
folder name 1
folder name 2
folder name 3
folder name 4
file name 1
file name 2
file name 3
folder name 1
1/2
PROGRAM (CD)
You may determine the order in which tracks will play.
1 In stop mode, press MODE.
¡The PROGRAM screen will appear.
2 Press Arrow (K/L) to select a track, then
press ENTER.
¡Press CLEAR/C.RESET
to erase the most recently
entered program.
3 Press PLAY to play the programmed tracks.
Notes
¡Press STOP once and then PLAY again, playback
will restart from the point where STOP was pressed.
¡Press STOP twice and then PLAY. Playback starts
from the first track in the original order. However,
the program can be called back when you follow the
above steps. Your programs will be stored unless
either the disc tray is opened or power is turned off.
¡Up to 99 programs can be entered.
¡To repeat the current track in the program, press
REPEAT repeatedly until TRACK appears during
playback. To repeat the entire program, press
REPEAT repeatedly until ALL appears during
playback.
¡To erase all programs at once, select ALL CLEAR
and press ENTER at step 2.
CD
CD-DA TOTAL 0:08:00
ENTER
ALL CLEAR
8 3:30
8 3:30
9 2:30
10 1:30
2/2
You can switch to the slide show mode during play-
back.
1 Press MODE during playback.
¡The slide show mode screen will appear.
¡The slide show mode cannot be switched when it is
stopped, or from the file list screen.
2 Press ENTER.
¡The slide show mode will change.
CUT IN/OUT:
The entire image appears in one time.
FADE IN/OUT: The image appears gradually and
then disappears.
3 Press MODE to exit.
JPEG
H9651UD.qx3 04.3.2 8:54 PM Page 26
–
27
–
EN
1L25
English
RANDOM PLAYBACK (MP3 / JPEG)
1 In stop mode, press MODE repeatedly until
the RANDOM screen appears.
2 Press PLAY to play the tracks in random
order.
JPEGMP3
This feature allows you to program an MP3 or JPEG
disc to play in a desired sequence.
1 Press MODE in the stop mode.
¡The PROGRAM screen will appear.
2 Press Arrow (K/L) to select a track, then
press ENTER, to save it in a program.
¡Press CLEAR/C.RESET to erase the incorrect input.
3 Press PLAY to start programmed playback.
Note
¡To erase all programs at once, select ALL CLEAR
and press ENTER at step 2.
JPEGMP3
PROGRAM (MP3 / JPEG)
AUDIO LANGUAGE
The DVD/VCR allows you to select a language (if
multiple languages are available) during DVD disc
playback.
1 Press AUDIO during playback.
2 Press AUDIO repeatedly to select your
desired language.
Note
¡Pressing AUDIO may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
DVD
STEREO SOUND MODE
1 Press AUDIO repeatedly during playback to
select between STEREO, L-CH or R-CH.
¡STEREO - both right and left channels are active
(stereo)
L-CH - only left channel is active
R-CH - only right channel is active
Note
¡If the Virtual Surround setting is 1 or 2, the sound
mode will be fixed to STEREO, and cannot be
changed.
CD
DVDs allow you to select a language for subtitles (if
available) during DVD disc playback.
1 Press SUBTITLE during playback.
2 Press SUBTITLE repeatedly to select your
desired subtitle language.
¡The selected language will be displayed on the dis-
play bar at the top of the screen.
3 To turn off subtitles, press SUBTITLE
repeatedly until OFF appears.
Notes
¡Some discs allow audio language setting/subtitle
language setting on the disc menu. (Operation varies
between discs, so refer to the manual accompanying
the disc.)
¡If the desired language is not shown after pressing
SUBTITLE several times, the disc does not have
subtitles in that language.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, “---” will be displayed instead.
(Refer to page 31.)
¡ It may take time to display the subtitles in the
selected language.
DVD
SUBTITLE LANGUAGE
H9651UD.qx3 04.3.2 8:54 PM Page 27
–
28
–
EN
1L25
1 Press SETUP in STOP mode.
2 Press Arrow (s/B) to select CUSTOM, then
press ENTER.
3 Press Arrow (s/B) to select PARENTAL,
then press ENTER.
PARENTAL
RATING LEVEL ALL
CHANGE
CHANGING THE ON-SCREEN
DISPLAY
You can check the information about the current disc
by pressing DISPLAY on the remote control.
1 Press DISPLAY during playback to show
current Chapter.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
2 Press DISPLAY again to show current Title.
¡The elapsed and remaining playing time of the cur-
rent title will be displayed.
3 Press DISPLAY for the third time.
¡The BIT RATE and the current repeat setting will be
displayed.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
4 Press DISPLAY for the fourth time to
remove the display.
DVD
9/49 0:03:21 –0:02:15
CAMERA ANGLE
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change
the camera angle when the ( ) mark appears on the
screen.
If the “ANGLE MARK” setting is “OFF” in the
Display setting, the
()
icon will not appear. (Refer to
page 30.)
1 Press ANGLE during playback.
¡The selected angle will be displayed on the display
bar at the top of the screen.
2 Press ANGLE repeatedly to select your
desired angle.
DVD
PARENTAL CONTROL
Parental Control provides limits for DVDs with extreme
violence or adult themes. (A password you establish
will override the limits.) This feature allows you to pre-
vent discs with objectionable scenes from being played
by your children.
PARENTAL LEVEL
Parental Level allows you to set the rating level of your
DVD discs. Playback will stop if the disc’s ratings
exceed the level you set.
1 Press DISPLAY during playback, the current
Track will be displayed on the TV screen.
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
2 Press DISPLAY again to show the total
Track.
¡The elapsed and remaining playing time of the disc
will be displayed.
3 Press DISPLAY for the third time to remove
the display.
1 Press DISPLAY during playback of an MP3
or JPEG disc.
¡The name of the file currently in play will be dis-
played.
2 Press DISPLAY again to show the track
number, the elapsed time, the repeat status,
and the playback status at the top of the
screen.
¡ will be displayed when the repeat play has been
selected.
T- indicates Track repeat
G- indicates Group (folder) repeat
A- indicates All (disc) repeat
3 Press DISPLAY again to exit.
JPEG
MP3
CD
H9651UD.qx3 04.3.2 8:54 PM Page 28
–
29
–
EN
1L25
English
CONTROL LEVELS
¡
ALL
All parental lock is cancelled.
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
¡
Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
¡
Level 1
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
DVD SETUP
AUDIO SETTINGS
Set your surround modes for DVD player
through your-
receiver or processor. DVD’s audio setup will not affect
CD playback.
1 Press SETUP in STOP mode.
2 Press Arrow (s/B) to select CUSTOM, then
press ENTER.
¡CUSTOM mode will appear.
3 Press Arrow (s / B) to
select AUDIO, then
press ENTER to con-
firm.
4 Press Arrow (K/L) to select an item, then
press ENTER.
DRC (Dynamic Range Control):
¡To compress the range of sound volume.
¡DRC function is available only on the discs that are
recorded in the Dolby Digital format.
¡The default setting is ON.
DVD
DOWN SAMPLING :
¡Set to ON when outputting in 48kHz.
¡Set to OFF when outputting the original sound.
¡The default setting is ON.
¡
When playing disc with copyright protection, the
sound will be down sampled at 48kHz even if you set
it to OFF.
¡
DOWN SAMPLING function is available only on
digital output of a disc recorded in 96kHz, and when
the unit is connected to another source using the digi-
tal out jack.
¡DOWN SAMPLING function is available only on
the discs recorded in the Dolby Digital format.
DOLBY DIGITAL :
¡Set to BITSTREAM when the player is connected
to Dolby Digital Decoder.
(BITSTREAM : Dolby Digital Output)
(PCM : Converts Dolby Digital to PCM)
¡The default setting is BITSTREAM.
DTS:
¡Set to BITSTREAM when connected to DTS
decoder.
¡The default setting is OFF.
4 Press SETUP to exit.
QUICK
QUICK
AUDIO
DRC ON
DOWN SAMPLING ON
DOLBY DIGITAL BITSTREAM
DTS OFF
IF YOU FORGET THE PASSWORD
1 Press 4, 7, 3, 7 at step 4.
¡Password will be cleared and parental level will be
set to ALL.
2 Proceed the above Steps 4-6 again.
4 Enter your four-digit password then press
ENTER.
5 Press Arrow (K/L) to select RATING
LEVEL, then press ENTER.
6 Press Arrow (K/L) to select the desired
level, then press ENTER.
7 Press SETUP to exit
Notes
¡When doing this for the first time, enter any 4 digits
except for 4737. That number will be used as the
password from the second time onward. If the pass-
word is already set, “CHANGE” appears on the dis-
play at step 5.
¡To change the password, press Arrow (K/L) to
select CHANGE, then press ENTER. Enter the four-
digit pass-word, then press ENTER.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
H9651UD.qx3 04.3.2 8:54 PM Page 29
–
30
–
EN
1L25
Adjust the Black Level Settings to make the black
parts of the picture as bright as you prefer.
1 Press MODE during playback.
2 Press ENTER to switch ON/OFF.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
3 Press MODE twice or RETURN to exit.
¡The setting will be saved even if the player is
turned off.
DVD
BLACK LEVEL SETTING
You can enjoy surround-sound effect over two speak-
ers.
1 Press SURROUND during playback.
2 Press SURROUND to set it 1 (Natural effect)
or 2 (Emphasized effect) or OFF.
3 Press MODE or RETURN to exit.
¡The setting will be saved even if the DVD/VCR is
turned off.
Notes
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO (for
CD play only).
¡Turn down the level or turn it “OFF” if the sound is
distorted.
MP3CD
DVD
VIRTUAL SURROUND
ON
OFF
You can change certain aspects of the DVD display
screens, on-screen messages and the display panel on
the front of the DVD/VCR.
1 Press SETUP in STOP mode.
2 Press Arrow (s/B) to select CUSTOM, then
press ENTER.
¡CUSTOM mode will appear.
3 Press Arrow (s / B) to select DISPLAY, then
press ENTER to con-
firm.
4 Press Arrow (K/L) to select the below
items, then press ENTER.
TV ASPECT:
¡Press Arrow (K/L) for an item selection, then
press ENTER.
¡4:3 LETTER BOX displays a theater-like image.
Black bars appear at the top and bottom of the
screen.
¡4:3 PAN-SCAN is the traditional TV mode with a
full height picture with both sides trimmed.
¡Select 16:9 WIDE if a wide-screen TV is connected
to the DVD player.
¡The default setting is 4:3 LETTER BOX.
STILL MODE :
¡Press K or L for an item selection (AUTO, FIELD
or FRAME), then press ENTER.
¡Select “AUTO” usually.
¡If you select FIELD, pictures in the still mode will
be stabilized although they will be coarse due to lit-
tle amount of data.
¡If you select FRAME, pictures in the still mode will
be highly defined although they will be blurred due
to output of two fields at the same time.
¡The default setting is AUTO.
ANGLE MARK:
¡Press ENTER repeatedly to turn Angle mark ON or
OFF.
¡The default setting is ON.
LOGO:
¡Press ENTER to switch ON (opening picture)/
OFF(black).
¡The default setting is ON.
5 Press SETUP to exit.
Notes
¡Be sure to press SETUP, or the setting will not work.
QUICK
DISPLAY SETTING
DISPLAY
TV ASPECT 4:3 L-BOX
STILL MODE AUTO
ANGLE MARK ON
LOGO ON
H9651UD.qx3 04.3.2 8:54 PM Page 30
–
31
–
EN
1L25
English
–
31
–
EN
1L25
Language options are not available on some discs.
1 Press SETUP in STOP mode.
2 Press Arrow (s/B) to select CUSTOM, then
press ENTER.
¡CUSTOM mode will appear.
3 Press Arrow (s / B) to select LANGUAGE,
then press ENTER to
confirm.
4 Press Arrow (K/L) to select an item, then
press ENTER.
¡If you want to return to the LANGUAGE SETTING
MENU, press Arrow(s ).
AUDIO:
¡Sets the audio language.
SUBTITLE:
¡Sets the subtitle language.
DISC MENU:
¡Sets the language for DVD menu.
PLAYER MENU:
¡Sets the language for the On-screen display.
QUICK
LANGUAGE SETTING
To Return All Selections of SETUP (except
for PARENTAL) to their Default Settings
LANGUAGE
AUDIO ORIGINAL
SUBTITLE OFF
DISC MENU ENGLISH
PLAYER MENU ENGLISH
A-B
Abkhazian 4748
Afar 4747
Afrikaans 4752
Albanian 6563
Amharic 4759
Arabic 4764
Armenian 5471
Assamese 4765
Aymara 4771
Azerbaijani 4772
Bashkir 4847
Basque 5167
Bengali;Bangla 4860
Bhutani 5072
Bihari 4854
Bislama 4855
Breton 4864
Bulgarian 4853
Burmese 5971
Byelorussian 4851
C-E
Cambodian 5759
Catalan 4947
Chinese [CHI] 7254
Corsican 4961
Croatian 5464
Czech 4965
Danish [DAN] 5047
Dutch [DUT] 6058
English [ENG] 5160
Esperanto 5161
Estonian 5166
F-H
Faroese 5261
Fiji 5256
Finnish [FIN] 5255
French [FRE] 5264
Frisian 5271
Galician 5358
Georgian 5747
German [GER] 5051
Greek [GRE] 5158
Greenlandic 5758
Guarani 5360
Gujarati 5367
Hausa 5447
Hebrew 5569
Hindi 5455
Hungarian [HUN] 5467
I-K
Icelandic [ICE] 5565
Indonesian 5560
Interlingua 5547
Interlingue 5551
Inupiak 5557
Irish [IRI] 5347
Italian [ITA] 5566
Japanese [JPN] 5647
Javanese 5669
Kannada 5760
Kashmiri 5765
Kazakh 5757
Kinyarwanda 6469
Kirghiz 5771
Kirundi 6460
Korean [KOR] 5761
Kurdish 5767
L-N
Laothian 5861
Latin 5847
Latvian;Lettish 5868
Lingala 5860
Lithuanian 5866
Macedonian 5957
Malagasy 5953
Malay 5965
Malayalam 5958
Maltese 5966
Maori 5955
Marathi 5964
Moldavian 5961
Mongolian 5960
Nauru 6047
Nepali 6051
Norwegian [NOR] 6061
O-R
Occitan 6149
Oriya 6164
Oromo(Afan) 6159
Panjabi 6247
Pashto;Pushto 6265
Persian 5247
Polish 6258
Portuguese [POR] 6266
Quechua 6367
Rhaeto-Romance 6459
Romanian [RUM] 6461
Russian [RUS] 6467
S
Samoan 6559
Sangho 6553
Sanskrit 6547
Scots Gaelic 5350
Serbian 6564
Serbo-Croatian 6554
Sesotho 6566
Setswana 6660
Shona 6560
Sindhi 6550
Singhalese 6555
Siswat 6565
Slovak 6557
Slovenian 6558
Somali 6561
Spanish [SPA] 5165
Sundanese 6567
Swahili 6569
Swedish [SWE] 6568
T
Tagalog 6658
Tajik 6653
Tamil 6647
Tatar 6666
Telugu 6651
Thai 6654
Tibetan 4861
Tigrinya 6655
Tonga 6661
Tsonga 6665
Tur kish [TUR] 6664
Tur kmen 6657
Twi 6669
U-Z
Ukrainian 6757
Urdu 6764
Uzbek 6772
Vietnamese 6855
Volapuk 6861
Welsh 4971
Wolof 6961
Xhosa 7054
Yiddish 5655
Yo r uba 7161
Zulu 7267
Language Code Language Code Language Code Language Code
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change
the Audio or Subtitle language setting on page 27. If you choose any other languages, ‘---’ will be displayed
instead. (3 letter language code is written in bracket.)
5 Press Arrow (K/L) to select a setting, then
press ENTER.
¡If OTHERS is selected on the AUDIO, SUBTITLE
or DISC MENU screen, press four-digit number to
enter the code for the desired language. (Refer to the
language code list below.)
¡Only the languages supported by the disc can be
selected.
6 Press SETUP to exit.
Note
¡Language Setting for Audio and Subtitle is not avail-
able with some discs. Then use the Audio and the
Subtitle button. Details are on page 27.
This allows you to return all selections of SETUP
(except for PARENTAL) to their default settings.
1 Press SETUP in STOP mode.
2 Press Arrow (s/B) to select INITIALIZE,
then press ENTER.
¡INITIALIZE mode will appear.
3
Press
Arrow (K/L)
to select YES, then press
ENTER.
4 Press ENTER to exit.
Note
¡When you cancel to initialize at step
3
, select NO.
DVD
H9651UD.qx3 04.3.2 8:54 PM Page 31
–
32
–
EN
1L25
TROUBLESHOOTING GUIDE
If the DVD/VCR does not perform properly when operated as instructed in this Owner's Manual, check the
DVD/VCR consulting the following checklist.
V
C
R
D
V
D
V
C
R
PROBLEM CORRECTIVE ACTION
No power. • Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
The DVD/VCR does not respond • Check if the power plug is connected to an AC outlet.
to the remote control. • Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles
between the sensor and the remote.
• You have to be within 23 feet of the DVD/VCR.
• Check if the correct mode is selected. If not switch the mode by pressing DVD or VCR,
whichever you need, on the remote control.
• Check if a cassette tape is in the DVD/VCR.
Timer recording is impossible. • Make sure the timer recording is set correctly by pressing TIMER.
• Make sure the TIMER light is on on the front panel, and “REC” and “ ” appear in the front
panel display. If not, press TIMER.
• Make sure the DVD/VCR clock is set correctly.
Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Put the DVD/VCR in VCR mode. Press VCR on the remote control so that the green VCR OUT-
PUT light is lit.
Playback picture is partially noisy
• Adjust tracking control for a better picture by pressing CH (o /p).
Cannot view a tape but the • Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
audio is OK
.
• Make sure the DVD/VCR is not in the Menu mode.
No, or poor, playback picture. • Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
TV programs cannot be seen • Re-check the ANT. IN and ANT. OUT connections. See page 13.
normally.
• Press VCR/TV.
• Press VCR on the remote control to put it in the VCR mode. Check if the green VCR OUTPUT
light is lit. Then, set it to the TV position by pressing VCR/TV.
Video or color fades in and out •
You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
when making a copy of a video tape.
Cannot remove the tape. • Check if the DVD/VCR is in the VCR mode. If not, press VCR on the remote control to switch
the mode.
No picture. • Connect the video cables firmly.
• Insert a correct video disc that plays on this DVD/VCR.
• Press DVD on the remote control. Check if the DVD OUTPUT Light is lit. Then try other DVD
feature.
• Check if the progressive/interlace mode is set correctly according to your TV.
Disc cannot be played
.•Insert the disc.
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
No sound
.•Connect the audio cables firmly.
•Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
No DTS audio is output
.•
Use a DIGITAL AUDIO OUT jack when outputting the DTS audio.
Distorted picture
.•Connect the DVD/VCR directly to the TV.
•
There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language •
The selected language is not available for audio or subtitles on the DVD disc.
does not match the set up.
This is not a malfunction
The camera angle cannot be •
The DVD disc does not
contain sequences recorded from different camera angles.
changed.
This is not a malfunction
Audio or subtitle language • The DVD disc does not contain audio source or subtitles in the selected language.
cannot be changed.
This is not a malfunction.
“Prohibited icon” appears on the • That operation is prohibited by the DVD/VCR or the disc.
screen, prohibiting an operation.
This is not a malfunction.
Notes
¡Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Instruction
Manual for details on correct operations.
¡Playback from a desired track and random playback are not available during program playback.
¡Some functions are prohibited on some discs.
D
V
D
H9651UD.qx3 04.3.2 8:54 PM Page 32
–
33
–
EN
1L25
English
MAINTENANCE
SERVICING
¡Should your DVD/VCR become inoperative, do not
try to correct the problem yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord, and please call our help line at 1-800-
448-2244 to locate an Authorized Service Center.
CLEANING THE CABINET
¡Use a soft cloth slightly moistened with a mild deter-
gent solution. Do not use a solution containing alco-
hol, spirits, ammonia or abrasives.
CLEANING DISCS
¡When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe
in a circular motion.
¡Do not use solvents such as benzine, thinner, com-
mercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for ana-
logue records.
CLEANING THE DISC LENS
¡If the DVD/VCR still does not perform properly
when it is operated while referring to the relevant
sections and to “TROUBLESHOOTING GUIDE” in
this Owner’s Manual, the laser optical pickup unit
may be dirty. Consult your dealer or an Authorized
Service Center for inspection and cleaning of the
laser optical pickup unit.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or remove a cas-
sette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while the TV
program reception is clear. Dirt accumulated on the video heads
after long periods of use, or the usage of rental or worn tapes can
cause this problem. If a streaky or snowy picture appears during
playback, the video heads in your DVD/VCR may need to be
cleaned.
1. Please visit your local Audio/Video store and purchase a good
quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call
our help line at 1-800-448-2244 to locate an Authorized Service
Center.
NOTES:
• Remember to read the instructions included with the video head
cleaner before use.
• Clean video heads only when problems occur.
RecordableRecordable
ReWritableReWritable
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your city office or consult the yellowpages for details.
DISC HANDLING
¡Use discs which have the following logos on them.
(Optical audio digital discs.)
¡Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
¡Always store the disc in its protective case when it is
not used.
¡To clean-off, use a soft cloth.
¡Do not use a hard cloth since this will mar the disc.
¡Wipe the disc in a straight line from center to edge.
¡Never wipe with a circular motion.
¡Do not use detergent or abrasive cleaning agents.
H9651UD.qx3 04.3.2 8:54 PM Page 33
–
34
–
EN
1L25
SPECIFICATIONS
Product type: DVD/VCR Combo (DVD player with Video Cassette Recorder)
Discs: DVD video
Audio CD
Video Cassette tape (VHS)
Converter output: VHF Channel 3 or 4.
Power source: 120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption: 21 W (standby: 3.6 W)
Operating temperature: 41°F (5°C) to 104°F (40°C)
Dimensions: W 17-3/16” (435 mm)
H 3-3/4” (94 mm)
D 9-3/16” (233 mm)
Weight: 6.0 lbs (2.7 kg)
¡Designs and specifications are subject to change without notice.
¡If there is a discrepancy between languages, the default language will be English.
H9651UD.qx3 04.3.2 8:54 PM Page 34
POWER/STANDBY
LINES
VIDEO IN L [mode] AUDIO IN R
REW F.FWD
STOP/EJECT
PLAY
REC/OTR
REC TIMER
PROGRESSIVE SCAN
DIGITAL AUTO TRACKING
DVD/VCR Combo DV-PF74U
MP3 / JPEG PLAY BACK DVD / CD / CD-R / CD-RW COMPATIBLE
STOP PLAY
OPEN/CLOSE
CHANNEL
VCR
OUTPUT
DVD
1
3
4
2
681012
14
20
791113
17
15
5
18
16
19
+10
EJECT
32
SEARCH MODE
OPEN/CLOSE
9
ZOOM
DISPLAY
8
AUDIO
0
TOP MENU
SETUP
PLAY
SKIP
CH
56
1
A-B REPEAT
REPEAT
7
CLEAR/C. RESET
SUBTITLE
MODE
ANGLE
DVD
VCR/TV
DISC
NAVIGATION
VCR
SLOW SPEED REC/OTR
RETURN
MENU
STOP
4
SURROUND
PAUSE/STEP
ENTER
TIMER
22
21
23
24
25
26
27
28
29
30
32
31
33
52
53
51
48
49
50
35
38
37
46
44
45
47
43
42
39
41
40
36
34
–
35
–
Español
SP
1L25
CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES
PANEL DELANTERO
PANEL REMOTO
1. Botón POWER/STANDBY
Presione para conectar y desconectar la alimentación.
2. COMPARTIMIENTO DE CASETES
3. Botón OPEN/CLOSE
Presione para insertar discos en o removerlos de la
bandeja de carga del disco.
4. Bandeja de carga del disco
5. Botón PLAY (DVD)
Presione para comenzar la reproducción.
Para activar / disactivar la exploración progresiva.
6. Botón STOP (DVD)
Detiene la operación del disco.
7. Luz DVD OUTPUT (verde)
Esta luz aparece cuando se selecciona el modo DVD.
Usted sólo puede mirar DVDs cuando la luz DVD
OUTPUT verde se encienda. Para que se encienda la luz
DVD OUTPUT verde, presione el DVD en el control
remoto o el OUTPUT en el panel delantero.
8. Botón OUTPUT
Presione para seleccionar el modo DVD o el modo VCR.
●
Usted puede cambiar el modo de salida ya sea presionando
el OUTPUT en el panel delantero o el DVD o VCR en el
control remoto. Sin embargo,
si usted presiona el
OUTPUT en el panel delantero primero, usted necesita
volver a seleccionar el modo correspondiente
presionando el DVD o el VCR en el control remoto.
9. Luz VCR OUTPUT (verde)
Esta luz aparece cuando se selecciona el modo VCR.
Usted sólo puede mirar cintas cuando la luz VCR
OUTPUT verde esta encendida. Para hacer que la luz
VCR OUTPUT verde se encienda, presione el VCR en el
control remoto o el OUTPUT en el panel delantero.
10. Botones CHANNEL
En el modo VCR, presione para cambiar canales de TV en la
DVD/VCR; presione para ajustar el seguimiento durante la
reproducción normal o en movimiento lento; presione para
remover las fluctuaciones verticales en una imagen fija.
11. Visualizador, ventanilla del sensor remoto
12. Luz TIMER
Esta luz se enciende cuando el DVD/VCR está en el
modo de espera o apagada para una grabación con
temporizador o durante una grabación de Un-Toque.
Parpadea si se presiona el TIMER para una grabación con
temporizador pero no hay cinta en el DVD/VCR.
Parpadea cuando todas las grabaciones con temporizador
o grabaciones de Un-Toque han terminado.
13. Botón REC/OTR
Presione una vez para iniciar una grabación. Presione
repetidamente para iniciar un Grabación de Un-Toque.
14. Luz REC
Se enciende durante la grabación.
15. Botón PLAY (VCR)
Presione para comenzar la reproducción.
16. Botón STOP/EJECT (VCR)
Botón de expulsion (EJECT)
Presione para sacar la cinta de la DVD/VCR.
Botón de parada (STOP)
Presione para detener el movimiento de la cinta.
17. Botón F.FWD (VCR)
Presione para avanzar rápidamente la cinta o ver la imagen
rápidamente en avance durante la reproducción (Búsqueda en
avance).
18. Botón REW (VCR)
Presione para rebobinar la cinta o para ver la imagen
rápidamente en inversión durante el modo de reprodución
(Búsqueda en rebobinado).
19. Toma de entrada de AUDIO
Conecte aquí cables de audio procedentes de las tomas de
salida de audio de un camcorder, otra videograbadora o
una fuente de video.
20. Toma de entrada de VIDEO
Conecte aquí un cable de video procedente de la toma de
salida de video de un camcorder, otra videograbadora o una
fuente de video (reproductor de discos láser, camcorder, etc.)
21. Botón SURROUND
Presione para activar el sonido tridimensional.
22. Botón
yy
/I (POWER/STANDBY)
Presione para conectar y desconectar la alimentación.
(Para las indicaciones del interruptor de funcionamiento,
“I” indica la conexión y “
yy
/I” indica el estado de espera
de alimentación eléctrica.
23. Botón A-B REPEAT
Cepite la reproducción de una sección seleccionada.
H9651UD.qx3 04.3.2 8:54 PM Page 35
–
36
–
SP
1L25
24. Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
25. Botón MODE
Activa el modo de reproducción de progama o reproducción
aleatoria cuando se reproducen CDs de audio o discos de
MP3/JPEG. Ajusta el nivel del negro y el Mode de
Presentación (Slide Show Mode).
26. Botón ZOOM
Amplía parte de una imagen reproducida en DVD.
27. Botón CREAR/C.RESET
●
Modo DVD
Presione para reponer el ajuste.
●
Modo VCR
Presione para reponer el contador. Presione para salir de la
pantalla MENU.
28. Botón ANGLE
Presione para cambiar el ángulo de cámara para ver la secuencia
que se está reproduciendo desde un ángulo diferente.
29. Botón SUBTITLE
Presione para seleccionar un idioma de subtítulo deseado.
Botón TIMER
Presione para poner la videograbadora en el modo de espera
para una grabación con temporizador.
30. Botón MENU
●
Modo DVD
Presione para visualizar el menú del disco.
●
Modo VCR
Presione para tener acceso al menú VCR.
31. Botones de flecha
● Modo DVD
Botones
p
/
o
/
B
/
s
Mueve el cursor y determina su posición.
● Modo VCR
Botones
p
/
o
Presione para entrar dígitos cuando ajuste el programa. (Por
ejemplo, ajuste el reloj o programa con temporizador.) Presione
para seleccionar los modos de ajuste del menú en pantalla.
Botón B
Cuando ajuste el programa (Por ejemplo: ajuste el reloj o
programa con temporizador), presione para determinar su
selección y proceder al siguiente paso que usted desea entrar.
Presione para determinar los modos de ajuste del menú en
pantalla. Presione para añadir o cancelar números de canal
durante el preajuste de canal.
Botón s
Presione para cancelar un ajuste de programa con
temporizador. Presione para corregir dígitos cuando ajuste el
programa. (Por ejemplo: ajuste de reloj o programa con
temporizador.) Presione para añadir o cancelar números de
canal durante el preajuste de canal.
32. Botón ENTER
Presione para aceptar un ajuste.
33. Botón RETURN
Vuelve a la operación previa.
34. Botón VCR/TV
Utilice para seleccionar la posición VCR o TV.
Este DVD/VCR no tiene una luz VCR/TV. Si aparece ruido
en su TV cuando enciende el DVD/VCR (modo VCR),
presione este botón.
●
Posición VCR
Para mirar la reproducción, para monitorear las
grabaciones de video o para mirar un TV utilizando el
sintonizador VCR.
●
Posición TV
Para mirar la TV o para mirar un programa mientras graba
otro.
Botón DISC NAVIGATION
Púlselo para visualizar las primeras ascenas de cada capítulo
del título que astá siendo reprocido.
35. Botón VCR
Presione para seleccionar el modo VCR para el control remoto.
●
Usted puede cambiar el modo OUTPUT ya sea
presionando el OUTPUT en el panel delantero o el DVD o
VCR en el control remoto. Sin embargo,
si usted presiona
el OUTPUT en el panel delantero primero, usted
necesita volver a seleccionar el modo correspondiente
presionando el DVD o el VCR en el control remoto.
36. Botón SLOW
Durante la reproducción de la cinta, presione para mirar
la cinta de video en movimiento lento. Presione el PLAY
para reanudasr la reproducción normal. Este botón no
afecta la reproducción de DVD.
37. Botones SKIP
●
Modo DVD
Presione para saltar capítulos o pistas.
38. Botón STOP
●
Modo DVD
Presione para detener el movimiento del disco.
●
Modo VCR
Presione para detener el movimiento de la cinta.
39. Botón h
●
Modo DVD
Presione para ver la imagen DVD en movimiento de
inversión rápida o para inversión rápida o para invertir
la reproducción de un CD de audio.
●
Modo VCR
Presione para rebobinar la cinta o para ver la imagen
rápidamente en inversión durante el modo de
reproducción (Búsqueda en Rebobinado).
40. Botón PAUSE/STEP
●
Modo DVD
Presione para hacer una pausa en la reproducción del
disco. Presione repetidamente para avanzar la imagen
DVD paso a paso (o un fotograma a cada vez).
●
Modo VCR
Mientras graba, presione para detener provisionalmente
la grabación (pausa). Presione por segunda vez para
reanudar la grabación normal. Usted no puede hacer
una pausa en la grabación de Un-Toque. O presione
durante la reprodución de la cinta para congelar la
imagen.
41. Botón g
●
Modo DVD
Presione para avanzar rápidamente el disco. Presione el
PAUSE/SETP, luego presione este botón para comenzar
la reproducción en movimiento lento. Presione este
botón repetidamente para cambiar la velocidad de
avance del movimiento lento.
●
Modo VCR
Presione para avanzar rápidamente la cinta o ver la
imagen rápidamente en avance durante la reproducción
(Búsqueda de avance).
42. Botón PLAY
●
Modo DVD
Presione para comenzar la reproducción.
●
Modo VCR
Presione para comenzar la reproducción.
43. Botones CH
●
Modo VCR
Presione para cambiar canales de TV en la
videograbadora.
44. Botón REC/OTR
Presione una vez para comenzar una grabación. Presione
repetidamente para comenzar una grabación de Un-Toque.
45. Botón SPEED
Presione para seleccionar la velocidad de grabación de
VCR (SP o SLP).
H9651UD.qx3 04.3.2 8:54 PM Page 36
–
37
–
Español
SP
1L25
46. Botón DVD
Presione antes de utilizar el control remoto para el modo DVD.
●
Usted puede cambiar el modo de salida ya sea presionando
el OUTPUT en el panel delantero o el DVD o VCR en el
control remoto. Sin embargo,
si usted presiona el
OUTPUT en el panel delantero primero, usted necesita
volver a seleccionar el modo correspondiente
presionando el DVD o el VCR en el control remoto.
47. Botón SETUP
Presione para entrar en el modo de preparación.
48. Botón TOP MENU
Presione para llamar el menú de título.
49. Botón DISPLAY
●
Modo DVD
Presione para tener acceso o remover la pantalla de
visualización durante la reproducción DVD o CD de
audio.
●
Modo VCR
Presione para tener acceso o remover la visualización
de estado en pantalla de la videograbadora.
50. Botón AUDIO
Presione para seleccionar un idioma de audio deseado o
modo de sonido.
51. Botones numéricos
●
Modo DVD
Presione para seleccionar directamente un capítulo o
título (DVD), o una pista (CD de audio o disco de
MP3/JPEG) para su reproducción.
●
Modo VCR
Presione para seleccionar canales de TV en la videograbadora.
Para seleccionar canales, entre el número de canal
como un número de dos dígitos para los resultados más
rápidos. Por ejemplo, para seleccionar el canal 6,
presione 0 y después 6.
52. Botón OPEN/CLOSE
Presione para abrir o cerrar la bandeja de carga del disco.
58. Botón EJECT
Presione para que salga el videocasete de la videograbadora.
53. Botón SEARCH MODE
●
Modo DVD
Presione para tener acceso o remover la indicación de
búsqueda que le permite ir directamente a un
título/capítulo/pista/tiempo/marcadore especificado.
●
Modo VCR
Presione para realizar una Búsqueda de tiempo o
Búsqueda de índice.
Precaución: No toque los pasadores interiores de las tomas
en el panel trasero. La descarga electroestática puede
dañar permanentemente el DVD/VCR.
DIGITAL
AUDIO OUT
COAXIAL
AUDIO
OUT
DVD V CR
DVD/VCR
S-VIDEO
OUT
AUDIO OUT
COMPONENT
VIDEO OUT
AUDIO IN
VIDEO OUT
LY
C
B/
PB
CR/
P
R
R
L
R
L
R
ANT-IN
ANT-OUT
VIDEO IN
0VM204468
1 2 3 8 9 1154
6 7 10
VISIÓN TRASERA
Nota
¡La toma S-VIDEO OUT, toma COAXIAL, y tomas COMPONENT VIDEO OUT son sólo útiles en el modo
DVD.
1. Cable de alimentación de CA
Conecte a una toma de corriente CA estándar para
suministrar corriente al DVD/VCR.
2. Toma COAXIAL (sólo DVD)
Conecte aquí un cable de audio digital coaxial opcional y
a la toma de entrada Audio Digital Coaxial de un
decodificador o receptor de audio.
3. Tomas DVD AUDIO OUT (sólo DVD)
Conecte aquí los cables de audio provistos y a las tomas de
entrada de audio de un televisor u otro equipo de audio (sólo
DVD).
4. Toma S-VIDEO OUT (sólo DVD)
Conecte aquí un cable de S-Video opcional y a la toma de
entrada de S-Video de un televisor.
5. Tomas COMPONENT VIDEO OUT (sólo DVD)
Conecte aquí los cables de videó componente opcionales y a
las tomas de entrada de Videó componente de un televisor.
6. Tomas DVD/VCR AUDIO OUT
Conecte aquí los cables de audio provistos y a las tomas
de entrada de audio de un televisor u otro equipo de
audio.
7. Tomas AUDIO IN
Conecte aquí los cables de audio procedentes de las
tomas de salida de audio de un camcorder, otra
videograbadora o una fuente de audio.
8. Toma DVD/VCR VIDEO OUT
Conecte aquí el cable de video amarillo (provisto) y a la
toma de entrada de video de TV.
9. Toma VIDEO IN (sólo VCR)
Conecte un cable procedente de la toma de salida de
video de un camcorder, otra videograbadora o una fuente
de audio-visual (reproductor de disco láser, reproductor
de disco de video, etc.) aquí.
10. Toma ANT-IN (Entrada de antena)
Conecte su antena, caja de cable o sistema de
radiodifusión directa.
11. Toma ANT-OUT (salida de antena)
Utilice el cable coaxial RF provisto para conectar esta
toma a la toma ANTENNA IN en su TV.
H9651UD.qx3 04.3.2 8:54 PM Page 37
–
38
–
SP
1L25
CAMBIO DE VCR/DVD
Como este producto utiliza videograbadoras y reproductores DVD, es necesario seleccionar el modo de
salida correcto.
+10
EJECT
32
SEARCH MODE
OPEN/CLOSE
9
ZOOM
DISPLAY
8
AUDIO
0
TOP MENU
SETUP
PLAY
SKIP
CH
56
1
A-B REPEAT
REPEAT
7
CLEAR/C. RESET
SUBTITLE
MODE
ANGLE
DVD
VCR/TV
DISC
NAVIGATION
VCR
SLOW SPEED REC/OTR
RETURN
MENU
STOP
4
SURROUND
PAUSE/STEP
ENTER
TIMER
POWER/STANDBY
LINES
VIDEO IN L [mode] AUDIO IN R
REW F.FWD
STOP/EJECT
PLAY
REC/OTR
REC TIMER
PROGRESSIVE SCAN
DIGITAL AUTO TRACKING
DVD/VCR Combo DV-PF74U
MP3 / JPEG PLAY BACK DVD / CD / CD-R / CD-RW COMPATIBLE
STOP PLAY
OPEN/CLOSE
CHANNEL
VCR
OUTPUT
DVD
VCR
OUTPUT
DVD
Bot n OUTPUT
Luz DVD OUTPUT
Luz VCR OUTPUT
Bot n DVD
Bot n VCR
Presione el VCR en el control remoto.
(Verifique que la luz VCR OUTPUT está encendida.)
CAMBIO AL MODO VCR
Notas
¡Presionando sólo el OUTPUT en el panel delantero no cambia el modo del control remoto. Usted siempre
necesita seleccionar el modo correcto en el control remoto, también.
Presione el DVD en el control remoto.
(Verifique que la luz DVD OUTPUT está encendida.)
CAMBIO AL MODO DVD
H9651UD.qx3 04.3.2 8:54 PM Page 38
–
39
–
Español
SP
1L25
CONEXION A UN SISTEMA DE AUDIO
DVD/VCR A CONEXION DE TV
1. Desconecte el cable de alimentación CA de la toma de corriente CA.
2. Desconecte la antena o cable del TV.
3. Conecte la antena o cable a la toma ANT-IN del DVD/VCR.
4. Conecte el DVD/VCR al TV utilizando el cable RF.
5. Enchufe los cables de alimentación CA del DVD/VCR y TV dentro de las tomas de corriente CA.
CANAL DE SALIDA RF
CONEXIONES
Por favor, vea la página 14 para detalles.
CONEXION A UN TV (PARA VIDEO)
Por favor vea la página 15 para detalles.
PREPARACION DE UN CANAL AUTOMATICO
PREPARACIÓN
1 Es necesario conectar primero la antena o
cable a la videograbadora. Luego conecte el
enchufe eléctrico de DVD/VCR a una toma
de corriente CA.
2 Encienda el TV y ponga el TV en el canal 3.
¡
Si aparece ruido, cambie el canal de salida RF de la
videograbadora al canal 4 presionando PLAY durante
3 segundos durante la reproducción. Luego seleccione
el mismo canal (4) en su TV. (Vea el “Canal de salida
RF” Para más detalles.)
3 Encienda la videograbadora presionando
yy
/I. Se encenderá la luz POWER.
4 Seleccione el idioma en la pantalla
(“INGLES”, “FRANCÉS” o ESPAÑOL”)
presionando
K o L. Luego presione B.
5 Comience el preajuste de canal presionando
B una vez. El sintonizador explora y
memoriza todos los canales activos en su
área.
¡La videocámara distingue entre los canales de TV
normales y los canales de cable.
6 Después de explorar, el sintonizador se
detiene en el canal memorizado más bajo. La
pantalla de TV retorna al modo TV.
¡Si aparece otra vez “AUTO SET UP” en la pantalla
de TV, inspeccione las conexiones de cable.
Presione nuevamente
B y la videograbadora
volverá a hacer el preajuste.
VCR
Si su TV no tiene terminales A/V:
1. Conecte el DVD/VCR a una TV mediante un cable RF (consulte CONEXIÓN DE DVD/VCR A TV).
2. Seleccione el canal 3 de su TV.
3. Inserte una cinta pregrabada en la unidad.
4. Pulse OUTPUT en el DVD/VCR para que se ilumine la luz VCR OUTPUT.
¡Si la luz “VCR” no aparece en la pantalla del panel delantero, pulse DVD/VCR en el mando a distancia.
5. Pulse PLAY.
¡Si aparece ruido, significa que el canal 3 ya está ocupado con otra emisión. En tal caso, cambie el canal de
salida de RF del VCR al canal 4 con los siguientes paso.
Si el canal 3 ya está ocupado con otra emisión,
1. Pulse PLAY una vez.
2. Tras unos segundos, pulse el botón PLAY en el DVD/VCR durante 3 segundos.
¡El canal de salida RF se cambiará al canal 4 y verá la imagen que se esté reproduciendo.
¡Si no aparece ninguna imagen, repita estos pasos.
¡Si hay un fallo de alimentación o el DVD/VCR está desenchufado durante más de 30 segundos, la
configuración del canal de salida de RF volverá al canal 3.
H9651UD.qx3 04.3.2 8:54 PM Page 39
–
40
–
SP
1L25
PREPARACION DE RELOJ
1 Seleccione el menú principal presionando
MENU.
¡
Si el reloj no está ajustado, aparece priemero el
menú CLOCK SET. En este caso, siga el paso (3).
2 Seleccione “CLOCK SET” presionando K o
L. Luego presione B.
3 Ajuste el reloj.
¡Para retroceder un paso, presione {.
4 Ponga en marcha el reloj presionando
CLEAR/C.RESET o
B.
VCR
AJUSTE DE RELOJ
MES DIA AÑO
03 / 17 MIE 2004
HORA MINUTO AM/PM
05 : 40 PM AM
PM
1) Ajuste el mes
Presione o o p repetidamente.
Luego presione B.
2) Ajuste el día
Presione o o p repetidamente.
Luego presione B.
3) Ajuste el año
Presione o o p repetidamente.
Luego presione B.
El día de la semana aparecerá automáticamente.
4) Ajuste la hora
Presione o o p repetidamente.
Luego presione B.
5) Ajuste el minuto
Presione o o p repetidamente.
Luego presione B.
6) Ajuste el AM o PM
Presione o o prepetidamente.
REPRODUCCIÓN BÁSICA
Para empezar
¡Conecte la alimentación del TV, amplificador y
cualquier otro componente que se encuentre
conectado al DVD/VCR.
¡Asegúrese que el TV y el receptor de audio (de venta
en los comercios) están en el canal correcto.
¡Seleccione el modo DVD presionando DVD en el
control remoto o la salida en el panel delantero.
1 Presione
yy
/I.
¡Aparecerá “Load” brevemente en el visualizador.
¡Asegúrese que la luz DVD OUTPUT está
encendida. Si no lo está, presione el botón DVD en
el control remoto para cambiar al modo DVD.
2 Presione OPEN CLOSE para abrir la
bandeja de carga del disco.
3 Ponga el disco elegido en la bandeja, con la
etiqueta hacia arriba.
4 Presione PLAY.
¡La bandeja se cerrará automáticamente y la
reproducción empezará luego desde el primer
capítulo o pista del disco. Si la reproduccón no
comienza automáticamente, presione PLAY.
5 Presione STOP para detener la
reproducción.
Notas
Puede aparecer un “icono de prohibición” O en la parte
superior derecha de la pantalla de TV durante el
funcionamiento, para avisar que hubo una operación
prohibida en el DVD/VCR o el disco.
¡Con los DVD que utilicen títulos para las señales de
programa de reproducción, la reproducción puede
empezar del segundo título o puede saltar estos
títulos.
¡Durante la reproducción de un disco de dos capas,
las imágenes pueden detenerse un momento. Esto
sucede cuando la primera capa cambia a la segunda
capa. Esto no es una avería.
¡Si un disco estás sucio o tiene rayas, las imágenes
pueden aparecer distorsionadas y la reproducción
puede detenerse. En estos casos, limpie el disco y
desenchufe el cable de corriente y enchufe
nuevamente antes de continuar con la reproducción.
JPEGMP3CDDVD
REPRODUCCIÓN DE UN DISCO
H9651UD.qx3 04.3.2 8:54 PM Page 40
MEMO
H9651UD.qx3 04.3.2 8:54 PM Page 41
–
42
–
Hitachi has made every effort to assure you hours of trouble free operation from your unit . However , should you require
service , a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico . Each
facility will provide you with convenient and expedient assistance . Our service "Hot line" operator will direct you to the
Hitachi Authorized Service Facility nearest you . Just present proof of purchase and/or delivery receipts to the Hitachi
Authorized Service Facility and service will be rendered in accordance with the terms of the limited warranty as stated
on your warranty card or operating guide .
Should you have any questions regarding in-warranty service, operation or technical assistance, please contact:
HITACHI AMERICA, LTD.
HOME ELECTRONICS DIVISION
900 Hitachi way,
Chula Vista, CA 91914-3556
Tel: 1-800-HITACHI
(1-800-448-2244)
HITACHI CANADA LTD .
DIGITAL MEDIA DIVISION
2495 Meadowpine Blvd., Mississauga,
Ontario L5N 6C3 CANADA
Tel: 1-800-HITACHI
(1-800-448-2244)
during the business hours
Monday - Friday EST 9:00am~7:00pm
Saturday EST 9:00am~5:00pm
durant les heures de hureau:
Lundi au Vedredi 9:00am~7:00pm (h.n.e.)
Samedi 9:00am~5:00pm (h.n.e.)
DECLARATION OF CONFORMITY
with FCC Rules for Electromagnetic Compatibility
Products: DVD PLAYER with VIDEO
CASSETTE RECORDER
Models: DV-PF74U
Trade Name: HITACHI
This device complies with part 15 of FCC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party: HITACHI AMERICA, LTD.
HOME ELECTRONICS DIVISION
900 Hitachi way,
Chula Vista, CA 91914-3556
Tel: 619-591-5200
H9651UD.qx3 04.3.2 8:54 PM Page 42
U.S.A. ONLY
NOT VALID IN CANADA
HITACHI
Warranty Limitations
The Limited Warranty provided by Hitachi does not cover:
A. Cabinet (exterior finish items), Battery packs, Accessories,
Lens Cleanings, Head Cleanings, DVD Disc Damage,
Video Tape Damage, or Software Modifications.
B. Any defect, malfunction, or failure caused by or resulting
from improper service, maintenance, repair, use of DVD
Cleaning Disks, use of Video Cleaning Cassettes, software,
or from abuse, neglect, accident or any other cause beyond
the control of Hitachi
C. Unpacking, set-up or installation, adjustment of customer
operated controls, user instruction.
D. Any product with Serial Numbers altered or removed
E. New products purchased or service performed outside of
the continental United States or its possessions
F. Product used for a commercial or industrial purpose.
NO PERSON, AGENT, DISTRIBUTOR, DEALER, SERVICE FACILITY, OR COMPANY IS
AUTHORIZED TO CHANGE, MODIFY, OR AMEND THE TERMS OF THIS LIMITED WAR-
RANTY IN ANY MANNER OR FASHION WHATSOEVER, EXCEPT AND TO THE EXTENT
PROVIDED IN THIS LIMITED WARRANTY, HITACHI MAKES NO EXPRESS WARRANTY
REGARDING THIS HITACHI PRODUCT. FURTHER, ALL IMPLIED WARRANTIES RELAT-
ING TO ANY PORTION OF THIS PRODUCT, INCLUDING ANY WARRANTY OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO 90
DAYS FOR LABOR AND ONE YEAR FOR PARTS, THE DURATION OF THE APPLICABLE
EXPRESS WARRANTY CONTAINED ABOVE. HITACHI SHALL
NOT BE LIABLE TO THE PURCHASER OR TO ANY OTHER PERSON FOR ANY INCI-
DENTAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFIT OF PRODUCT
RESULTING FROM ANY DEFECT IN OR MALFUNCTION OR FAILURE OF THIS
HITACHI PRODUCT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
Important Notice:
Retain your sales receipt for warranty purposes. Please complete
the section below for your records as it may be needed in the
event of loss.
Attach your sales receipt to this card.
DVD, VCR, Camcorder Products, AC Adapter
Charger Limited Warranty Registration
(for your records)
Model No.
Serial No.
Date of Purchase
Dealer Name
Dealer Address
City State Zip
✄
REGISTER YOUR PRODUCT ON-LINE AT
HITACHI.COM/TV
OR MAIL IN TO ADRESS ON THIS CARD.
HITACH
I
“In order to allow Hitachi to better serve customer needs, please
complete this card and return it to Hitachi America, Ltd., Home
Electronics Division Completion of this card is not required in order
to validate your Hitachi limited warranty, but would assist us in
developing better services and programs for our customers.”
(Please print or type)
✄
Model No.
Serial No.
Customer Name
Date of purchase
Customer Address
City
State Zip
Phone No.
( )
Dealer name
Dealer address
City
State Zip
H9651UD.qx3 04.3.2 8:54 PM Page 43
U.S.A. ONLY
NOT VALID IN CANADA
✄
✄
HITACHI
• DVD Products
• VCR Products
• CAMCORDER Products
• AC ADAPTER CHARGER
Conditions of Hitachi Limited Warranty
These Hitachi Products are warranted to be free of defects in
parts and workmanship at the time of purchase by the original
owner. If this product is found to be defective, Hitachi will repair or
replace defective parts at no charge to the original owner. Parts
used for replacement are warranted for the remainder of the origi-
nal Limited Warranty period. For 90 days from the date of original
purchase, Hitachi will provide labor for the repair or replacement
of defective parts without charge, subject to the following condi-
tions:
1. Owner must provide verification of the date of purchase when
requesting Limited Warranty Service. (Dated Sales Receipt
Required)
2. All repairs must be performed by a Hitachi Authorized Service
Facility.
3. This warranty is valid only in the U.S.A.
LIMITED WARRANTY
Hitachi America, Ltd., Home Electronics Division (“Hitachi,”) war-
rants this component in duration as stated below:
Register your product on-line at hitachi.com/tv
or mail this portion to the following address
Attn: Warranty Department
Hitachi America, Ltd., Home Electronics Division
900 Hitachi Way
Chula Vista, CA 91914-3556
QT15271
Printed in China
TJ17533
©Hitachi, Ltd. 2004
0VMN04193
H9651UD
★★★★★
Hitachi America, Ltd.
Home Electronics Division
• 90 DAYS LABOR (Carry-in)
• 1 YEAR PARTS (Except Battery)
For information concerning repairs, operation, technical assis-
tance or for referral to the location of your nearest Authorized
Service Facility or Parts Distributor, call: 1-800-HITACHI (1-800-
448-2244)
HITACHI AMERICA, LTD
HOME ELECTRONICS DIVISION
900 Hitachi Way
Chula Vista, CA 91914-3556
Tel: 1-800-HITACHI
REGISTER YOUR HITACHI PRODUCT ON-LINE AT
HITACHI.COM/TV
(Continued on reverse side)
H9651UD.qx3 04.3.2 8:54 PM Page 44
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Hitachi DV PF74U Manual de usuario

Hitachi
Marca
Hitachi
Modelo
DV PF74U
Categoría
Reproductores de DVD
Tipo
Manual de usuario
Descargar PDF
informe

En otros idiomas

Documentos relacionados

Otros documentos