Dolby Laboratories DVD960/P02 Manual de usuario

Marca: Dolby Laboratories

Modelo: DVD960/P02

Categoría: Reproductores de DVD

Tipo: Manual de usuario

DVD VIDEO PLAYER & VIDEO

CASSETTE RECORDER

SD-V396SU

OWNER’S MANUAL

Introduction

Connections

Basic setup

Playback

(VCR)

Recording

(VCR)

Other functions

(VCR)

DIGITAL VIDEO

Basic playback

(DVD)

Advanced

playback

(DVD)

Function setup

(DVD)

This device does not tape-record copy protected DVD Video Discs.

Others

2C53601A (E)COV 3/10/04, 11:301

Introduction

IMPORTANT SAFEGUARDS

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain

or moisture.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN

BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Changes or modifications not expressly approved by the partly responsible for compliance with the

FCC Rules could void the user's authority to operate this equipment.

CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CARE-

FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTE-

NANCE, CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLO-

SURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.

DO NOT STARE INTO BEAM.

The lightning flash with arrowhead symbol, within an

equilateral triangle is intended to alert the user to the presence

of uninsulated dangerous voltage within the product's

enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature

accompanying the appliance.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

Location of the required Marking

The rating sheet and the safety caution are on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE

STANDARDS, 21 CFR SUBCHAPTER J.

2C53601A (E)p02-13 3/10/04, 11:302

Introduction

1. READ INSTRUCTIONS

All the safety and operating instructions should be read before the unit is operated.

2. RETAIN INSTRUCTIONS

The safety and operating instructions should be retained for future reference.

3. HEED WARNINGS

All warnings on the unit and in the operating instructions should be adhered to.

4. FOLLOW INSTRUCTIONS

All operating and use instructions should be followed.

5. CLEANING

Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning the exterior cabinet only.

6. ATTACHMENTS

The manufacturer of this unit does not make any recommendations for attachments, as they may cause

hazards.

7. WATER AND MOISTURE

Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet

basement, or near a swimming pool.

8. ACCESSORIES

Do not place this unit on an unstable cart, stand, tripod, bracket, or table.

The unit may fall, causing serious injury, and serious damage to the unit.

8A. An appliance and cart combination should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the appliance and cart

combination to overturn.

9. VENTILATION

Slots and openings in the cabinet back or bottom are provided for ventilation,

to ensure reliable operation of the unit, and to protect it from overheating.

These openings must not be blocked or covered. The openings should never be blocked by placing the unit

on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat

source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided and/or the manufacturer’s instructions have been adhered to.

10. POWER SOURCE

This unit should be operated only from the type of power source indicated on the rating plate. If you are not

sure of the type of power supply to your home, consult your appliance dealer or local power company. For

units intended to operate from battery power, or other sources, refer to the operating instructions.

11. GROUNDING OR POLARIZATION

This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the

other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to

insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your

electrician to replace your obsolete outlet. Instead of the polarized alternating-current line plug, your unit

may be equipped with a 3-wire grounding-type plug (a plug having a third (grounding) pin). This plug will

only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug

into the outlet, contact your electrician to replace your obsolete outlet.Do not defeat the safety purpose of

the grounding-type plug.

12. POWER-CORD PROTECTION

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed

upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point

where they exit from the appliance.

S3125A

PORTABLE CART WARNING

(symbol provided by RETAC)

IMPORTANT SAFEGUARDS

2C53601A (E)p02-13 3/10/04, 11:303

Introduction

IMPORTANT SAFEGUARDS

13. LIGHTNING

To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the

unit due to lightning and power line surges.

14. POWER LINES

An outside antenna system should not be located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an

outside antenna system, extreme care should be taken to keep from touching such power lines or circuits,

as contact with them might be fatal.

15. OVERLOADING

Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

16. OBJECT AND LIQUID ENTRY

Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short

out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

17. OUTDOOR ANTENNA GROUNDING

If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is

grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the

National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for

the grounding electrode.

18. SERVICING

Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified service personnel.

For example:

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating instructions. Adjust only those controls

that are covered by the operating instructions, as an improper adjustment of other controls may result in

damage and will often require extensive work by a qualified technician to restore the unit to its normal

operation.

e. If the unit has been dropped or the cabinet has been damaged.

f . When the unit exhibits a distinct change in performance, this indicates a need for service.

19. REPLACEMENT PARTS

When replacement parts are required, be sure the service technician uses replacement parts specified by

the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

20. SAFETY CHECK

Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to

determine that the unit is in proper operating condition.

21. HEAT

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

22. DISC TRAY

Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

23. CONNECTING

When you connect the product to other equipment, turn off the power and unplug all of the equipment from

the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's

manual of the other equipment carefully and follow the instructions when making any connections.

2C53601A (E)p02-13 3/10/04, 11:304

Introduction

EXAMPLE OF ANTENNA GROUNDING AS PER THE

NATIONAL ELECTRICAL CODE

24. LASER BEAM

Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the

laser beam. It may cause sight damage.

25. DISC

Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious

personal injury and product malfunction.

26. NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-

nected to the grounding system of the building, as close to the point of cable entry as practical.

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert

the AC cord plug into a standard 120V 60Hz polarized AC outlet.

Notes:

•

Never connect the AC line cord plug to other than the specified

voltage (120V 60Hz). Use the attached power cord only.

•

If the polarized AC cord does not fit into a non-polarized AC

outlet, do not attempt to file or cut the blade. It is the user’s

responsibility to have an electrician replace the obsolete outlet.

•

If you cause a static discharge when touching the unit and the

unit fails to function, simply unplug the unit from the AC outlet

and plug it back in. The unit should return to normal operation.

Polarized AC Cord Plug

(One blade is wider than the other.)

AC Outlet

Wider Hole

and Blade

Power source

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

ANTENNA LEAD IN WIRE

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUND CLAMP

ELECTRIC SERVICE

EQUIPMENT

NEC-NATIONAL ELECTRICAL CODE

S2898A

IMPORTANT SAFEGUARDS / Power source

2C53601A (E)p02-13 3/10/04, 11:305

Introduction

Notes on handling

When shipping the DVD/VCR, the original shipping

carton and packing materials come in handy. For

maximum protection, repack the unit as it was

originally packed at the factory.

Do not use volatile liquids, such as insect spray, near

the DVD/VCR. Do not leave rubber or plastic

products to contact the DVD/VCR for a prolonged

period. They will leave marks on the finish.

The top and rear panels of the DVD/VCR may

become warm after a long period of use. This is not a

malfunction.

When the DVD/VCR is not in use, be sure to remove

the disc and the video cassette turn off the power.

If you do not use the DVD/VCR for a long period, the

unit may not function properly in the future. Turn on

and use the DVD/VCR occasionally.

Notes on locating

Place the DVD/VCR on a level surface. Do not use it

on a shaky or unstable surface such as a wobbling

table or inclined stand. The loaded disc or the video

tape may become dis-aligned and damage the DVD/

VCR.

When you place this DVD/VCR near a TV, radio, or

VCR, the playback picture may become poor and the

sound may be distorted. In this case, place the DVD/

VCR away from the TV, radio, or VCR.

Notes on cleaning

Use a soft, dry cloth for cleaning.

For stubborn dirt, soak the cloth in a weak detergent

solution, wring well and wipe. Use a dry cloth to wipe

it dry.

Do not use any type of solvent, such as thinner and

benzine, as they may damage the surface of the

DVD/VCR.

If you use a chemical saturated cloth to clean the unit,

follow that product’s instructions.

To obtain a clear picture

The DVD/VCR is a high technology, precision device. If

the video head, the head drum, the optical pick-up lens

or disc drive parts are dirty or worn down, the picture

quality will deteriorate. To obtain a clear picture, we

recommend regular inspection and maintenance

(cleaning or parts replacement) every 1,000 hours of

use depending on the operating environment. For

details, contact your nearest dealer.

Notes on moisture condensation

Moisture condensation damages the DVD/VCR.

Please read the following carefully.

Moisture condensation occurs, for example, when you

pour a cold drink into a glass on a warm day. Drops of

water form on the outside of the glass. In the same way,

moisture may condense on the head drum or the optical

pick-up lens inside this unit, one of the most crucial

internal parts of the DVD/VCR.

Moisture condensation occurs during the

following cases.

When you bring the DVD/VCR directly from a cold

place to a warm place.

When you use the DVD/VCR in a room where you

just turned on the heater, or a place where the cold

wind from the air conditioner directly hits the unit.

In summer, when you use the DVD/VCR in a hot and

humid place just after you move the unit from an air

conditioned room.

When you use the DVD/VCR in a humid place.

Do not use the DVD/VCR when moisture

condensation may occur.

If you use the DVD/VCR in such a situation, it may

damage discs and internal parts. Remove the disc or

the video tape, connect the power cord of the DVD/

VCR to the wall outlet, turn on the DVD/VCR, and

leave it for two or three hours. After two or three

hours, the DVD/VCR will have warmed up and

evaporated any moisture. Keep the DVD/VCR

connected to the wall outlet and moisture

condensation will seldom occur.

Precautions

Tape

Head drum

It’s too

warm!

Wait!

Wall outlet

2C53601A (E)p02-13 3/10/04, 11:306

Introduction

Notes on discs

On handling discs

Do not touch the playback side of the disc.

Do not attach paper or tape to discs.

On cleaning discs

Fingerprints and dust on the disc cause picture and

sound deterioration. Wipe the disc from the center

outwards with a soft cloth. Always keep the disc

clean.

If you cannot wipe off the dust with a soft cloth, wipe

the disc lightly with a slightly moistened soft cloth and

finish with a dry cloth.

Do not use any type of solvent such as thinner,

benzine, commercially available cleaners or antistatic

spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight

or near heat sources.

Do not store discs in places subject to moisture and

dust such as a bathroom or near a humidifier.

Store discs vertically in a case. Stacking or placing

objects on discs outside of their case may cause

warping.

Playback side

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

Track 1 Track 2 Track 3 Track 4 Track 5

Structure of disc contents

Normally, DVD video discs are divided into titles, and

the titles are sub-divided into chapters. VIDEO CDs and

audio CDs are divided into tracks.

DVD video disc

Video CD/Audio CD

Each title, chapter or track is assigned a number, which

is called “title number”, “chapter number” or “track

number” respectively.

There may be discs that do not have these numbers.

Notes on copyright

It is forbidden by law to copy, broadcast, show,

broadcast on cable, play in public, and rent copyrighted

material without permission.

This device does not tape-record copy protected DVD

Video Discs.

The device is not to be used for copying copyrighted

content without the express written permission of the

Obtaining such permission is the sole responsibility of

the user.

This product incorporates copyright protection

technology that is protected by method claims of certain

U.S. patents and other intellectual property rights

owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology

must be authorized by Macrovision Corporation, and is

intended for home and other limited viewing uses only

unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is

prohibited.

Video CD/Audio CD

2C53601A (E)p02-13 3/10/04, 11:307

Introduction

DIGITAL VIDEO

About this owner’s manual

This owner’s manual explains the basic instructions of

this DVD/VCR. Some DVD video discs are produced in

a manner that allows specific or limited operation during

playback. As such, the DVD/VCR may not respond to all

operating commands. This is not a defect in the DVD/

VCR. Refer to instruction notes of discs.

“

” may appear on the TV screen during operation.

A “

” means that the operation is not permitted by the

DVD/VCR or the disc.

For example, sometimes it is unable to stop the

playback of copyright message of the disc when the

STOP (3) button is pressed. Alternatively, the “

” may

also indicate that the feature is not available for the disc.

Notes on region numbers

The region number of this DVD/VCR is 1. If region

numbers, which stand for their playable area, are printed

on your DVD video disc and you do not find

ALL

disc playback will not be allowed by the player. (In this

case, the DVD/VCR will display a message on-screen.)

On Video CDs

This DVD/VCR supports Video CDs equipped with the

PBC (Version 2.0) function. (PBC is the abbreviation of

Playback Control.) You can enjoy two playback

variations depending on types of discs.

• Video CD not equipped with PBC function

(Version 1.1)

Sound and movie can be played on this DVD/VCR in

the same way as an audio CD.

• Video CD equipped with PBC function

(Version 2.0)

In addition to operation of a Video CD not equipped

with the PBC function, you can enjoy playback of

interactive software with search function by using the

menu displayed on the TV screen (Menu Playback).

Some of the functions described in this owner’s

manual may not work with some discs.

Playable discs

This DVD/VCR can play the following discs.

• You cannot play discs other than those listed above.

• You cannot play discs of DVD-RAM, DVD-ROM,

Photo CD, etc., or non standardized discs even if they

may be labeled as above.

• Some CD-R/RWs can not be played back depending

on the recording conditions.

• This DVD/VCR uses the NTSC color system, and

cannot play DVD video discs recorded in any other

color system (PAL, SECAM, etc.).

Notes on discs (continued)

DVD

video

discs

Disc Mark

Contents

Disc

Size

Maximum

playback time

Video

CDs

Approx. 4 hours

(single sided disc)

Approx. 8 hours

(double sided disc)

Approx. 80 minutes

(single sided disc)

Approx. 160 minutes

(double sided disc)

Approx. 74 minutes

Approx. 20 minutes

8 cm

12 cm

8 cm

12 cm

Audio

Video

(moving

pictures)

Audio

Video

(moving

pictures)

Audio

CDs

Approx. 74 minutes

Approx. 20 minutes

8 cm

(CD

single)

12 cm

Audio

The following discs are also available.

DVD-R/RW discs of DVD video format

CD-R/CD-RW discs of CD-DA, Video CD, SVCD,

MP3, WMA or JPEG format

Kodak Picture CD and FUJICOLOR CD format

Some of these discs may be incompatible.

2C53601A (E)p02-13 3/10/04, 11:308

Introduction

IMPORTANT SAFEGUARDS .......................... 2

Power source ................................................... 5

Precautions ...................................................... 6

Notes on discs.................................................. 7

Contents. .......................................................... 9

Identification of controls ................................. 10

Antenna connections...................................... 14

CATV (CABLE TV) connections..................... 16

Connecting to a TV ........................................ 18

Connecting to optional equipment.................. 20

Introduction

Recording a TV program ................................ 34

One-touch Timer Recording (OTR) ................ 36

Timer recording .............................................. 37

Recording (VCR)

Stereo recording and playback ...................... 39

Second Audio Program (SAP)........................ 39

Duplicating a video tape ................................. 40

Recording a DVD/CD disc.............................. 41

Other functions (VCR)

Loading and unloading a cassette tape ......... 29

Cassette tape playback .................................. 30

Special playback ............................................ 31

Convenience function..................................... 32

Playback (VCR)

Setting the video channel ............................... 22

Setting the language ...................................... 23

Clock setting................................................... 24

Tuner setting .................................................. 27

Basic setup

Playing a disc ................................................. 42

Basic playback (DVD)

MP3/WMA/JPEG playback ............................ 45

Zooming ......................................................... 50

Locating desired scene .................................. 50

Marking desired scenes ................................. 51

Repeat playback ............................................ 52

A-B Repeat playback ..................................... 52

Program playback (CD).................................. 53

Random playback (CD) .................................. 53

Changing angles ............................................ 54

Title selection ................................................. 54

DVD menu...................................................... 54

Advanced playback (DVD)

Language code list ......................................... 67

Troubleshooting ............................................. 68

Specifications ................................................. 69

Limited warranty ............................................. 70

Others

Contents

Connections

Function setup (DVD)

Changing soundtrack language ..................... 55

Setting surround sound .................................. 55

Setting subtitles .............................................. 56

Karaoke playback........................................... 56

E.B.L. (Enhanced Black Level) ...................... 57

Setting the aspect ratio of TV screen ............. 58

Setting on screen display ............................... 59

Status display of disc ..................................... 59

Dynamic Range Control ................................. 60

Parental control setting .................................. 61

To change the parental level .......................... 62

Temporary disabling of rating level by DVD disc ..

Setting OSD language ................................... 64

Setting language ............................................ 65

Selecting PROGRESSIVE scan..................... 66

2C53601A (E)p02-13 3/10/04, 11:309

Introduction

Identification of controls

See the page in for details.

Front panel

Rear panel

When connecting the optical digital cable, remove

the cap and fit the connector into the jack firmly.

When not using the jack, keep the cap inserted

to protect it from dust intrusion.

ON/STANDBY

button

AUDIO (L/R)/VIDEO IN

(LINE IN 2) jacks

EJECT button

Cassette loading slot

Disc tray

Display window

REC button

CHANNEL M/? buttons

OPEN/CLOSE button

STOP button

PLAY button

FF (Fast Forward)

button

REW (Rewind) button

VCR/DVD mode selector button

Remote sensor

VCR indicator

DVD indicator

DVD S-VIDEO

OUT jack

S-VIDEO/COMPONENT

Video selector switch

AC power cord

DVD OPTICAL DIGITAL AUDIO

OUT jack (dust protection cap)

DVD AUDIO (L/R)

OUT jacks

DVD COAXIAL DIGITAL

AUDIO OUT jack

DVD COMPONENT

OUT jacks

RF OUT jack

RF IN jack

AUDIO (L/R)/VIDEO

IN (LINE IN1) jacks

DVD/VCR common AUDIO

(L/R)/VIDEO OUT jacks

2C53601A (E)p02-13 3/10/04, 11:3110

Introduction

VCR operation status

CH 125

8 : 47

MON

00 : 00 : 00 SP

STEREO SAP

While watching TV

DAY OF THE WEEK

CHANNEL

TAPE SPEED

REAL TIME COUNTER

CLOCK

STEREO AND

SECOND

AUDIO

PROGRAM

(SAP)

While operating a tape

OPERATING

MODE

TAPE IN

AUTO REPEAT

HI-FI STEREO

DVD/CD/VCD operation status

Display window

Press CALL to display information on screen.

To cancel the display, press CALL again.

Recording :

Rec/Pause

Play :

Stop :

Eject :

VCR Icons

34:56 71:33

Track 11/99

00:34:56 01:12:33

Each press of DISPLAY, the status display of the disc will appear on the screen and change as follows.

DVD

00:34:56 01:12:33

1/9

Title 1/99

1/8

1/32

Chapter 1/999

Eng DolbyDigital

Eng

CD/VCD

DISC

OPERATION

TRACK NO.

ELAPSED TIME

CHAPTER NO.

ANGLE NO.

A KIND OF AUDIO

DISC OPERATION

TITLE NO.

ELAPSED

TIME

TOTAL

TIME

TOTAL

TIME

OUTPUT SELECTION

Timer Recording indicator (VCR)

Multifunctional indicator

Recording

indicator (VCR)

Track indicator (CD)

Tape loaded indicator (VCR)

Play indicator

VCR indicator (VCR)

Still indicator

Disc inserted indicator (DVD)

Disc inserted

indicator (CD)

AM/PM indicator

(AM is not displayed)

Progressive indicator

AUDIO LANGUAGE

SUBTITLE LANGUAGE

2C53601A (E)p02-13 3/10/04, 11:3111

Introduction

Remote control

* MENU button

Use the MENU button to display the menu included on

many DVD video discs. To operate a menu, follow the

instructions in “DVD Menu.”

Identification of Controls (continued)

The instructions in this manual describe the functions on the remote control. See the page in for details.

FWDREW

STOP

PAUSE/STILL

VCR

DVD

CALL

DISPLAY

TV/VCR

AUDIO SELECT

AUDIO

ATR

SUBTITLE

A-B RPT

CLOCK/COUNTER

SP/SLP

PLAY MODE

COUNTER RESET

ANGLE

INPUT SELECT

PROGRESSIVE

INDEX

SKIP

INDEX

SKIP

TIMER REC

REC/OTR

OPEN/CLOSE

EJECT

MARKER

SET

–

TOP MENU RETURN

ZERO RETURN

JUMP

VCR MENU

SETUP

CM SKIP

ZOOM

CANCEL

ENTER

PLAY

654

321

SLOW

+–

OPEN/CLOSE button (DVD)

ENTER button

RETURN button

CANCEL button

CLOCK/COUNTER button

CM SKIP button

ZOOM button

MARKER button

INPUT SELECT button

PROGRESSIVE button

PAUSE/STILL button

SLOW button

VCR DVD selector button

SP/SLP button

PLAY MODE button

AUDIO SELECT button

AUDIO button

FWD button

INDEX + button

SKIP button

A-B RPT button

PLAY button

Channel +/– buttons

CALL button

DISPLAY button

INDEX – button

SKIP button

TIMER REC button

SET +/

buttons

EJECT button (VCR)

TOP MENU button

VCR MENU button

SETUP button

TV/VCR button

ATR button

SUBTITLE button

COUNTER RESET button

ANGLE button

REW button

ZERO RETURN button

JUMP button

STOP button

REC button

OTR button

*MENU button

( / / / )

Direction buttons

Direct channel

selection buttons

Number buttons

) buttonPower (

2C53601A (E)p02-13 3/10/04, 11:3112

Introduction

Operation

• Aim the remote control at the remote sensor and press control buttons to

operate.

• Operate the remote control within 30° angle on either side of the remote

sensor, up to a distance of Approx. 7 meters.

Replace the compartment

cover.

Install two “R03/AAA” batteries

(supplied),

paying attention to the

polarity diagram in the battery

compartment.

Slide the battery compartment

cover in the direction of the

arrow.

Approx. 7 meters

Battery precautions

The precautions below should be followed when using batteries in this device:

1. Use only the size and type of batteries specified.

2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.

Re-

versed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.

Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.

4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from

possible battery leakage.

5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery

manufacturer’s directions.)

• Press POWER (

) to turn the DVD VCR on or off.

• Select your desired operating mode (DVD or VCR) using VCR DVD.

(DVD or VCR indicator on the front panel will show you which mode is selected.)

• Press CH + or CH – to move through the channels one channel at a time.

• The CH +/– (

/ ) and SET +/– ( / ) are also used to navigate on-screen menu system.

• You can directly access specific channels using Number buttons.

• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the

DVD screen (DVD mode).

Remote control basics

Inserting batteries

2C53601A (E)p02-13 3/10/04, 11:3113

Connections

OUT

(TV)

(ANT)

Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to

the DVD/VCR properly.

• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type

antenna is required.

• If you are not sure about the connection, please refer to qualified service personnel.

The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV and

connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna

system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.

If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and

one 75 ohm output.

Note:

Combination VHF/UHF Antenna with 75 ohm Coaxial Cable

Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire

Separate VHF and UHF Antennas

DVD/VCR

VHF

UHF

300 ohm Twin Lead (Flat) Wire

(not supplied)

Matching Transformer 300 ohm Input 75

ohm output (not supplied)

300 ohm Twin Lead (Flat) Wire

(not supplied)

75 ohm Coaxial Cable

Combiner 75/300 ohm Inputs 75 ohm output

(not supplied)

DVD/VCR

Antenna connections

If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber, skip ahead to page 16

for the proper connections.

Antenna to DVD/VCR connection

2C53601A (E)p14-17 3/10/04, 11:3114

Connections

UHF

VHF

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to

the “TV” mode.

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to

the “TV” mode.

Note: If a VHF or UHF antenna is used,

set the TV/CATV menu option to

the “TV” mode.

75 ohm Coaxial Cable (supplied)

Splitter 75 ohm Input

75/300 ohm outputs

(not supplied)

Splitter 75 ohm Input

300 ohm outputs

(not supplied)

TV with single 75 ohm VHF/UHF antenna

input

TV with 300 ohm UHF and 75 ohm VHF

antenna inputs

TV with 300 ohm UHF and 300 ohm VHF

antenna inputs

After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.

Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the

connection diagram.

This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna

inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.

75 ohm Coaxial Cable

(supplied)

75 ohm Coaxial Cable

(supplied)

DVD/VCR to TV connection

2C53601A (E)p14-17 3/10/04, 11:3115

Connections

CATV (CABLE TV) connections

Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This

DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company

supplied converter box, except for those premium channels which are intentionally scrambled. If you subscribe to a

premium channel which is scrambled, you must have a descrambler box for proper reception.

Allows:

Recording of nonscrambled channels.

Use of the programmable timer.

Recording of one channel while watching another.

Allows:

Recording of channels through the converter box

(scrambled and unscrambled).

Using the programmable timer to record only the

channel selected at the converter box.

Prevents:

Recording one channel while watching another.

Using the DVD/VCR tuner to select channels.

DVD/VCR

Incoming Cable

Converter/

Descrambler

Incoming

Cable

To record from converter/descrambler,

DVD/VCR tuner must be tuned to the con-

verter output channel, usually channel 3

or 4.

Note:

DVD/VCR

Note: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of

the Converter/Descrambler box, usually channel 3 or 4.

Incoming Cable

Converter/Descrambler

Allows:

Recording of nonscrambled channels.

Use of the programmable timer.

Recording an unscrambled channel while watching

any channel selected at the converter box.

Prevents: Recording scrambled channels.

If you are playing a tape or using the tuner

built into the DVD/VCR, the converter must

be set to the video channel output of the

DVD/VCR (either 3 or 4).

Note:

2C53601A (E)p14-17 3/10/04, 11:3116

Connections

This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scram-

bled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Con-

sult your local cable company for more information concerning connection to their descrambler equipment. There are

many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.

IMPORTANT: Make sure the TV/CATV menu option is set to the “CATV” mode.

Incoming Cable

Allows:

Recording of one channel while watching another.

Using the programmable timer to record only the channel selected at the converter box.

Recording of all channels through the converter box.

Prevents:

Watching scrambled channels while recording another channel.

Using the DVD/VCR tuner to select channels.

DVD/VCR

Splitter

Converter/Descrambler

DVD/VCR

Converter/Descrambler

A/B Switch

Incoming Cable

Splitter

Allows:

Recording of nonscrambled channels.

Recording of one channel while watching another.

Watching premium channels through the converter while recording nonscrambled channels.

Using the programmable timer.

Prevents: Recording scrambled channels.

DVD/VCR

Splitter

Converter/Descrambler

A/B Switch

Allows:

Recording of all channels through the converter box.

Recording a scrambled or unscrambled channel while watching another (scrambled or

unscrambled) channel.

Using the programmable timer to record only the channel selected at the converter box.

Prevents: Using the DVD/VCR tuner to select channels.

A/B Switch

Incoming Cable

Converter/Descrambler

2C53601A (E)p14-17 3/10/04, 11:3117

Connections

Connecting to a TV

Connect the DVD/VCR to your TV.

To VIDEO

OUT

To ANALOG AUDIO OUT

(red) (white)

(yellow)

Signal flow

To wall outlet

To video input

(yellow)

(red)

(white)

Audio/video cable (supplied)

To audio inputs

Notes:

• Refer to the owner’s manual of the connected TV as well.

• When you connect the DVD/VCR to your TV, be sure to turn off the power and unplug both units from the wall outlet before

making any connections.

• If your television set has one audio input, connect the left and right audio outputs of the DVD/VCR to a Y cable adapter (not

supplied) and then connect to your TV.

• Connect the DVD/VCR directly to your TV. If you connect the DVD/VCR to a VCR, TV/VCR combination or video selector, the

playback picture may be distorted as DVD video discs are copy protected.

TV or monitor with

audio/video inputs

Connecting to a TV

Note: This method transports VHS and DVD-video signals. For enhanced DVD-video performance, we recommend you

also connect the S-video or ColorStream

component video outputs to your TV/monitor

2C53601A (E)p18-25 3/10/04, 11:3118

Connections

Notes:

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the

wall outlet before making any connections.

• If you place the DVD/VCR near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD/

VCR away from the tuner and radio.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate

listening level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the

speakers may be damaged.

• When connecting to a TV using the Video or S-video jack, make sure that the Progressive indicator “ ” on the

display window is not lit. If it is lit, the Video and S-video outputs do not feed the correct signals and you cannot see

any picture. To turn off the Progressive indicator, select PROGRESSIVE scan Off

Note: The S-video output and component video output transports the DVD-video signal exclusively and will deliver

enhanced DVD video picture performance.

If you connect the DVD/VCR to your TV

with the DVD OUT jacks, select the

corresponding video input on your

television to watch DVD video discs.

TV or monitor with

ColorStream

component video inputs

PR/CR

video input

To PR/CR

VIDEO

OUT

Signal flow

To wall outlet

To audio inputs of

the amplifier

(red)

(white)

(red)

(white)

To Y

VIDEO

OUT

To PB/CB

VIDEO

OUT

To Y video input

PB/CB

video input

Audio system

To ANALOG

AUDIO OUT

To S-

VIDEO

OUT

Component video

cable (not supplied)

To S-video input

S-video cable (not supplied)

When you make this connection, set the S-VIDEO/

COMPONENT Video selector switch to the desired

position.

And also you must select the corresponding video

input on your TV.

Audio cable (not supplied)

S-video output/input

An S-Video connection is superior to Video (Yellow) output. Use this method for DVD playback when the connected television has S-

Video input, and does not have component video inputs.

Component video outputs/inputs

PROGRESSIVE outputs/inputs

Some TVs or monitors are equipped with component video inputs that are capable of reproducing a progressively scanned video

signal. Connecting to these inputs allows you to view the highest quality pictures with less flicker.

INTERLACED outputs/inputs

Some TVs or monitors are equipped with component video inputs. Connecting to these inputs allows you to enjoy the highest quality

DVD picture playback.

Notes:

• Actual labels for component video inputs may vary depending on the TV manufacturer. (ex. Y, R-Y, B-Y or Y, CB, CR)

• In some TVs or monitors, the color levels of the playback picture may be reduced slightly or the tint may change. In such a

case, adjust the TV or monitor for optimum performance.

Connecting to an audio system and TV equipped with S-video input/component video inputs

2C53601A (E)p18-25 3/10/04, 11:3119

Connections

75 Ω coaxial cable

Connecting to optional equipment

You can enjoy high quality dynamic sounds of DVD video discs or

audio CDs by connecting the DVD/VCR to optional audio

equipment.

For connection to your TV, see “Connecting to a TV”

: Front speaker

: Rear speaker

: Sub woofer

: Center speaker

: Signal flow

Connecting to an amplifier equipped with a Dolby Digital decoder

Connecting to an amplifier equipped with Dolby Surround Pro Logic

Dolby Surround Pro Logic

You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an amplifier and speaker system (right and left

front speakers, a center speaker, and one or two rear speakers).

Connecting to an amplifier equipped with a DTS decoder

Digital Theater Systems (DTS)

DTS is a high quality surround technology used in theaters and now available for home use,

on DVD video discs or audio CDs.

If you have a DTS decoder or processor, you can obtain the full benefit of 5.1 channel DTS

encoded sound tracks on DVD video discs or audio CDs.

Manufactured under license from

Dolby Laboratories. “Dolby” “Pro

Logic” and the double-D symbol are

trademarks of Dolby Laboratories.

• Use DVD video discs encoded via

the Dolby Digital recording

system.

• Use DVD video discs or audio

CDs encoded via the DTS

recording system.

Connect one or two rear speakers.

The output sound from the rear speakers

will be monaural even if you connect two

rear speakers.

“DTS” and “DTS Digital Out” are trademarks

of Digital Theater Systems, Inc.

With an amplifier equipped with Dolby Digital

Connect the equipment the same way as described in “Connecting to an amplifier

equipped with a Dolby Digital decoder.” Refer to that amplifier’s owner’s manual and set

the amplifier so you can enjoy Dolby Surround Pro Logic sound.

With an amplifier not equipped with Dolby Digital

Connect the equipment as follows.

• This connectin is only suitable for Video CDs and Audio CDs.

Dolby Digital

Dolby Digital is the surround sound technology used in theaters showing the latest movies,

and is now available to reproduce this realistic effect in the home. You can enjoy motion

picture and live concert DVD video discs with this dynamic realistic sound by connecting the

DVD/VCR to a 6 channel amplifier equipped with a Dolby Digital decoder or Dolby Digital

processor. If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of

Pro Logic from the same DVD movies that provide full 5.1-channel Dolby Digital

soundtracks, as well as from titles with the Dolby Surround mark.

Connect either.

To OPTICAL

type digital

audio input

Amplifier equipped with a

Dolby Digital decoder

Optical digital cable

75 Ω coaxial cable

To COAXIAL

type digital

audio input

Amplifier equipped with

Dolby Surround Pro Logic

Amplifier equipped with a

DTS decoder

Connect either.

To OPTICAL

type digital

audio input

Optical digital cable

To COAXIAL

type digital

audio input

• This selection uses the following reference mark.

Audio cable

To ANALOG AUDIO OUT

To Audio

input

2C53601A (E)p18-25 3/10/04, 11:3120

Connections

75 Ω coaxial cable

Optical digital cable

75 Ω coaxial cable

Warning

When playing DTS-encoded discs (audio CDs), excessive noise may be output from the analog stereo jacks. To avoid

possible damage to the audio system, you should take proper precautions when the ANALOG AUDIO OUT (L/R) jacks of the

DVD/VCR are connected to an amplification system. (Do not leave the ANALOG AUDIO OUT (L/R) wires dangling.) To enjoy

DTS Digital Surround™ playback, an external 5.1 channel DTS Digital Surround™ decoder system must be connected to the

BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR.

Connecting to an amplifier equipped with an MPEG2 audio decoder

MPEG2 sound

You can enjoy motion picture and live concert DVD video discs with dynamic realistic sound by connecting an amplifier equipped with

an MPEG2 audio decoder or MPEG2 audio processor.

Connecting to an amplifier equipped with a digital audio input

2 channel digital stereo

You can enjoy the dynamic sound of 2 channel digital stereo by connecting an amplifier equipped with a digital audio input and speaker

system (right and left front speakers).

Notes:

• DO NOT connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the AC-3 RF input of a Dolby Digital Receiver.

This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the BITSTREAM/PCM AUDIO

OUT jack of the DVD/VCR.

• Connect the BITSTREAM/PCM AUDIO OUT jack of the DVD/VCR to the “OPTICAL” or “COAXIAL” input of a Receiver or

Processor.

• Refer to the owner’s manual of the connected equipment as well.

• When you connect the DVD/VCR to other equipment, be sure to turn off the power and unplug all of the equipment from the

wall outlet before making any connections.

• The output sound of the DVD/VCR has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening

level. Otherwise, the speakers may be damaged by a sudden high volume sound.

• Turn off the amplifier before you connect or disconnect the DVD/VCR’s power cord. If you leave the amplifier power on, the

speakers may be damaged.

• Use DVD video discs encoded via

the MPEG2 recording system.

Amplifier equipped with an

MPEG2 audio decoder

Connect either.

To OPTICAL

type digital

audio input

Optical digital cable

To COAXIAL

type digital

audio input

Amplifier equipped with

a digital audio input

Connect either.

To OPTICAL

type digital

audio input

To COAXIAL

type digital

audio input

2C53601A (E)p18-25 3/10/04, 11:3121

Basic setup

Setting the video channel

When a TV is connected with the 75 ohm coaxial cable only.

To view playback of a recorded tape or DVD disc, or to watch a

program selected by the VCR's channel selector, the TV must be set to

channel 3 or 4 (video channel).

Setting the video channel

Press POWER to turn on the DVD/VCR.

Press VCR DVD selector to select the VCR mode.

Turn ON the TV and set to CH 3 or 4 to corre-

spond with the channel selected in step 1.

Press TV/VCR to select the VCR position.

Select any channel to receive a TV station in your area.

The channel number will appear on the screen for

about 4 seconds.

The VCR indicator on the

front panel will light.

The VCR indicator will

appear in the display

window.

For a push-button TV tuner

If CH 3 or 4 corresponding to the video channel cannot

be tuned on your TV, proceed as follows: set the VCR

3/4 channel selector and the TV to CH 3 or 4, play

back a prerecorded tape and tune the TV to receive a

sharp color picture from the video cassette recorder.

Refer to your TV owner's manual for details.

Note:

If the unit does not operate properly, or No key operation

(by the unit and/or the remote control): Static electricity, etc.,

may affect the player's operation. Disconnect the AC power cord

once, then connect it again.

POWER

VCR DVD

TV/VCR

Press and hold 3 or 4 on the remote for 3

seconds in standby mode.

The video channel will

start to flash for 3

seconds in the display

window.

VCR

DVD

TV/VCR

2C53601A (E)p18-25 3/10/04, 11:3122

Basic setup

Press SET + or – to select “LANGUAGE”, then

press ENTER.

Press VCR MENU.

The VCR menu screen will appear.

Press SET + or – to select “SYSTEM

SETUP”, then press ENTER.

If you use the unit for the first time and

press VCR MENU, instead of the main

menu screen the “SYSTEM SETUP”

menu screen in step 2 may appear.

Setting the language

You can choose from three different languages (English,

French and Spanish) for the on-screen displays.

Press SET + or – to select the desired language:

English (ENGLISH), Spanish (ESPAÑOL) or

French (FRANCAIS), then press ENTER.

Press VCR MENU until the MENU screen is

cleared.

Notes:

• Both the VCR and the DVD have their own player menus

• If no buttons are pressed for more than 60 seconds, the VCR

MENU screen will return to normal TV-operation automatically.

Preparation:

• Turn ON the TV and select to the corresponding

video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

1–3

1,4

VCR DVD

1–3

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

2C53601A (E)p18-25 3/10/04, 11:3123

Basic setup

Connect the Antenna or Cable system.

• If you use a cable box, turn it on.

Clock setting

The AUTO CLOCK function will automatically set the built-in clock

(Month, Day, Year and Time) when the DVD/VCR is connected to an

Antenna or Cable system and it is turned off. The DVD/VCR searches for

a station in your area containing the necessary AUTO CLOCK setting

signals. Once received, it will take approximately 4 minutes for the clock

to set itself automatically.

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

AUTO CLOCK setting

Plug the AC Power cord to the AC outlet.

Make sure the DVD/VCR is turned off.

• If you press POWER, the Auto Clock

set is not programmed.

Wait at least three minutes and press

POWER.

Press CALL to check the clock setting on

the on screen display.

If the clock is not set, check the antenna

condition. The AUTO CLOCK may not

function properly if the reception condition

is not good.

AUTO CLOCK adjustment

To set AUTO CLOCK to off

The auto clock adjustment will be updated at 6:00

AM, 12:00 PM and 6:00 PM everyday when the

DVD/VCR turned off.

• If you use a cable box and you want AUTO CLOCK

adjustment to be performed, the cable box must be

left on.

• The AUTO CLOCK adjustment is not effective when

there is a difference of more than 5 minutes exists

between the built-in clock time and the actual time.

When shipped from factory the AUTO CLOCK is set to “ON”.

But if you do not want AUTO CLOCK setting:

Press VCR MENU.

Press SET + or – to select “SYSTEM SETUP”,

then press ENTER.

Press SET + or – to select “AUTO CLOCK”.

Press ENTER to select “OFF”.

Press VCR MENU repeatedly to return to the

normal screen.

• When the AUTO CLOCK is set to

“OFF”, the AUTO CLOCK adjust-

ment does not function.

• Set the clock manually

CH 125

8 : 47

AM MON

00 : 00 : 00 SP

STEREO SAP

POWER

2,3

2,4

1,5

CALL

VCR DVD

CALL

DISPLAY

VCR MENU

SETUP

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

2C53601A (E)p18-25 3/10/04, 11:3124

Basic setup

Press VCR MENU.

Press SET + or – to select “SYSTEM SETUP”,

then press ENTER.

Press

SET + or –

to select “STANDARD TIME”

then press ENTER.

Press SET + or – to select your time zone,

then press ENTER.

Press VCR MENU twice to return to the

normal screen.

In the rare event that you live within broadcast range of two

stations in two different time zones, the DVD/VCR may

recognize the wrong station for the AUTO CLOCK setting.

To correct the situation:

Notes:

• To be able to select the standard time, the clock must first be

set by AUTO CLOCK once.

• If you live in Newfoundland and the AUTO CLOCK does not

function properly, set the AUTO CLOCK menu option to “OFF”

and set the clock manually.

Press VCR MENU.

Press SET + or – to select “SYSTEM SETUP”,

then press ENTER.

Press SET + or – to select “DAYLIGHT

SAVING TIME”, then press ENTER.

Press SET + or – to select one of the

options, then press ENTER. Press VCR

MENU until the MENU screen is cleared.

Notes:

• When shipped from factory, the DAYLIGHT SAVING TIME is

set to “AUTO” position.

• When the clock is not set, DAYLIGHT SAVING TIME setting

is not available.

• When there is no DAYLIGHT SAVING TIME in your area, al-

ways select “OFF” position in step 3.

When you want to set the

DAYLIGHT

SAVING TIME

manually, on the first

Sunday in April you set to “ON”, and

on the last Sunday in October you set

to “OFF”.

ON:

OFF:

AUTO:

for manual setting

(forward one hour)

for manual setting

(back one hour)

for automatic setting

(read XDS in the signal)

ATLANTIC : GMT–4hours

EASTERN : GMT–5hours

CENTRAL : GMT–6hours

MOUNTAIN : GMT–7hours

PACIFIC : GMT–8hours

ALASKA : GMT–9hours

HAWAII : GMT–10hours

AUTO : AUTO SET

(GMT: Greenwich Mean Time)

To set DAYLIGHT SAVING TIME

You can set the DAYLIGHT SAVING TIME automatically or

manually.

To set STANDARD TIME

VCR MENU

SETUP

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

SET

–

ENTER

2C53601A (E)p18-25 3/10/04, 11:3125

Basic setup

CANCEL

Press VCR MENU.

EXAMPLE: Setting the clock to “8:30 AM” March,

27 (SAT), 2004.

8 : 30AM SAT

Manual clock setting

After setting the clock, date and time starts

functioning automatically.

Note:

After a power failure or disconnection of the power, the timer

settings will be lost. In this case, reset the present time.

To make corrections any time during the process

Press CANCEL repeatedly until the item you want to

change blinks, then press SET + or –.

Press SET + or – to select “SYSTEM SETUP”,

then press ENTER.

Press SET + or – to select “CLOCK SET”,

then press ENTER.

Press SET + or – to set the month, then press

ENTER.

Set the day, year and time as in step 4.

Clock setting (continued)

If the AUTO CLOCK process did not set the date and time correctly,

you must set them manually for timer recording and DAYLIGHT

SAVING TIME.

2–4

〈+/

–

/ENTER/CANCEL/MENU

〉

MONTH

DAY

YEAR

TIME

1 (MON)

2004

12 : 00

–

/ENTER/CANCEL/MENU

MONTH

DAY

YEAR

TIME

27 (SAT)

2004

8 : 30

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

2–4

2C53601A (E)p26-31 3/10/04, 11:3226

Basic setup

Tuner setting

This DVD/VCR is equipped with a channel memory feature which allows

channels to skip up or down to the next channel set into memory,

skipping over unwanted channels. Before selecting channels, they must

be programmed into the DVD/VCR’s memory. In addition to normal

VHF and UHF channels, this DVD/VCR can receive up to 113 Cable

TV channels. To use this DVD/VCR with an antenna, set the TV/CATV

menu option to the TV mode. When shipped from the factory, this menu

option is in the CATV mode.

Press VCR MENU. Press

SET + or –

to select

“CH SETUP”, then press ENTER.

Press SET + or – to select “TV/CATV”.

TV/CATV selection Setting channels automatically

Repeat left step 1 and press SET + or – to

select “AUTO CH MEMORY”.

Press ENTER.

Auto tuning will begin. The channel dis-

play will count up and when finished,

the screen returns to normal.

CH 002

Note:

You can’t select “CH SETUP” if you set the channel to “L1” or

“L2”.

Press ENTER to select the TV or CATV mode.

The arrow indicates the selected mode.

Press VCR MENU until the menu screen is

cleared.

TV - VHF/UHF channels

CATV - CABLE TV channels

1,2

1,3

1,4

VCR DVD

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

Preparation:

• Turn ON the TV and select to the corresponding

video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

2C53601A (E)p26-31 3/10/04, 11:3227

Basic setup

Repeat the step 1 on page 27. Then press SET +

or – to select the “ADD/DELETE” and press

ENTER.

To ADD/DELETE channels

Press VCR MENU until the menu screen is

cleared.

To Add or Delete desired channels

CH SETUP

TV CATV

AUTO CH MEMORY

ADD/DELETE

/ENTER/MENU

654

321

Press Number buttons or SET + or – to select

a channel number you want to add or delete.

To add channels

Press ENTER until “ADD” appears on the

screen.

To delete channels

Press ENTER until “DELETE” appears on the

screen. The channel number will blink.

Repeat to to add or delete other channel.

1 2

Tuner setting (continued)

Noise elimination

When you don't want to receive a weak signal broadcast, a

Blue back screen can be obtained by selecting the NO NOISE

BACKGROUND “ON”. When the unit is shipped from the fac-

tory, the NO NOISE BACKGROUND is set to “ON”.

Repeat the steps 1~2 on page 26 and press

SET + or – to select “NO NOISE

BACKGROUND”.

Press ENTER to select “ON” or “OFF” position.

Press VCR MENU until the menu screen is

cleared.

NUMBER BUTTONS

1,2

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

2C53601A (E)p26-31 3/10/04, 11:3228

Basic setup

Loading and unloading a cassette tape

Use only video cassette tapes marked and .

Remove the erase prevention tab with a screwdriver.

Cover the hole with a piece of adhesive tape.

To record again

Screwdriver

Automatic tape eject

This DVD/VCR will automatically rewind the tape when the tape has ended. Once the tape is rewound to its beginning,

the cassette tape will be ejected automatically.

Press EJECT on the front panel or on the Remote.

Push the center of the tape until it is automatically

inserted.

Insert the cassette tape with its labeled side facing up

and the erase prevention tab positioned at your left. An

inverted cassette tape cannot be inserted.

Automatic playback

When loading a cassette tape without an erase prevention tab, playback will start automatically.

Automatic power ON

When you insert a cassette tape the DVD/VCR power will turn ON automatically.

Erase prevention tab

Adhesive tape

Remove the cassette tape.

Erase prevention tab

Unloading

To prevent accidental erasure

Tape speed and maximum recording time

Video cassette tape

Tape Speed

SLP (Super Long Play)

T-160 T-120 T-90 T-60 T-30

2-2/3 hours 2 hours 1-1/2 hours 1 hour 30 minutes

8 hours 6 hours 4-1/2 hours 3 hours 1-1/2 hours

SP (Standard Play)

Playback (VCR)

EJECT

Playback (VCR)

2C53601A (E)p26-31 3/10/04, 11:3229

Playback (VCR)

Cassette tape playback

To play a prerecorded tape.

Load a prerecorded tape

(When loading a cassette tape without the erase

prevention tab, playback will start automatically).

Preparation:

• Turn ON the TV and select the corresponding video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light).

Press PLAY.

Playback will start. “ ” will appear

on the screen for about 4 seconds.

Press STOP once.

The tape will stop but remain fully

loaded and ready to play.

“ ” will appear on the screen for

about 4 seconds.

To stop playback

Stop the playback or recording via STOP on remote.

To discontinue the tape-winding, press STOP. To switch to

playback directly (without STOP), press PLAY.

Notes:

• This VCR selects the playback tape speed SP, LP or SLP au-

tomatically.

• The Cassette tape and DVD disc can be played back simulta-

neously. If you press VCR DVD selector, the tape playback

and DVD playback alternate with each other on the screen

(via CH3, 4 or video connection).

To start playback

Playback Rewind or forward the tape

To rewind the tape:

Press REW.

To forward the tape:

Press FWD.

Forward/Reverse picture search mode

When the tape is being winded, you can switch to picture

search mode (see next page). To do this, press REW or

FWD and hold it down. The unit will resume the tape

advance or rewinding as soon as the button is released.

PLAY

STOP

FWD

REW

VCR DVD

PLAY

FWD

REW

2C53601A (E)p26-31 3/10/04, 11:3230

Playback (VCR)

Special playback

Picture search

Reverse picture search function

Press REW once or twice during playback.

Forward picture search function

Press FWD once or twice during playback.

To return to playback, press PLAY.

Press PAUSE/STILL during playback.

To resume normal playback, press PLAY or PAUSE/STILL.

During playback press SLOW.

To return to playback, press PLAY or SLOW.

Whenever you insert a tape and start playback, the

automatic tracking feature continuously analyzes the signal

to enable optimum picture quality during playback.

Press PAUSE/STILL during playback.

Press SLOW repeatedly: The picture advances frame by

frame.

To return to playback, press PLAY or PAUSE/STILL.

Slow tracking and vertical lock adjustment

If noise bars appear in the picture during slow motion,

press the SET + /– to reduce the noise bars.

If the still picture jitters excessively, press SET +/– to

stabilize the still picture.

Automatic tracking adjustment

If automatic tracking cannot eliminate noises well during

playback, press SET +/– to eliminate the noise. “MANUAL

TR.” will appear on the screen. Press it briefly for a fine

adjustment, or press and hold for a coarse adjustment.

Manual tracking adjustment

SPEED SEARCH TIMES

Adjusting tracking condition

Still picture

Slow motion

Frame by frame picture

Notes:

•

The audio output is muted during SPEED SEARCH, STILL,

FRAME ADVANCE and SLOW MOTION.

• During picture search mode there will be noise bars. This is

not a defect.

• Playback will commence after approx. 5 minutes to protect

the video tape against excessive wear during pause mode.

Press ATR to reactivate automatic tracking again.

“AUTO TR.” will appear on the screen.

PICTURE SEARCH SPEED

PRESS TWICE

TAPE SPEED

PRESS ONCE

SP (Standard Play)

LP (Long Play)

SLP (Super Long Play)

5 X

9 X

15 X

3 X

7 X

9 X

REW

PLAY

FWD

SLOW

ATR

SET +/–

PAUSE/STILL

Video head cleaning

Video head clogging

The video heads are the means by

which the DVD/VCR reads the picture

from the tape during playback. In the

unlikely event that the heads become

dirty enough to be clogged, no picture

will be displayed. This can easily be

determined if, during playback of a

known good tape, there is good sound,

but no picture (picture is extremely

snowy). If this is the case, have the

DVD/VCR checked and cleaned by

qualified service personnel.

Notes:

•

DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR

SERVICE THE UNIT BY REMOVING THE REAR COVER.

•

Video heads may eventually wear out and should be re-

placed when they fail to produce clear pictures.

•

To help prevent video head clogging, use only good qual-

ity VHS tapes. Discard worn out tapes.

Good Picture

Snowy Picture

CM skip

Press CM SKIP during playback. The DVD/VCR will search

forward through approximately 30 seconds of the tape (e.g.

unwanted commercial time) for each press of CM SKIP

(maximum six presses) and then resume normal playback.

For example : 1 press: 30 seconds of tape

2 press: 60 seconds of tape

3 press: 90 seconds of tape

CM SKIP

2C53601A (E)p26-31 3/10/04, 11:3231

Playback (VCR)

Convenience function

To cancel repeat mode:

Follow the above step 1, then press ENTER to select

“OFF” position. Press VCR MENU to return to the TV.

Press VCR MENU.

Press SET + or – to select “AUTO

REPEAT”.

Press ENTER to select “ON” or “OFF”.

If “ON” is selected, the playback

will be repeated endlessly.

Press VCR MENU until the menu screen is

cleared.

If you press CALL, “ ” will

appear on the screen

To commence playback, press PLAY.

The playback will be repeated

endlessly.

This function rewinds the tape to the

“00:00:00”

counter position

automatically.

Press CLOCK/COUNTER.

The counter display shows the tape run-

ning time during playback or recording.

Press COUNTER RESET at the desired tape

position.

The counter display will be reset to

“00:00:00” position (e.g. the beginning

of recording).

Press STOP when playback or recording is

completed.

Press ZERO RETURN.

The tape will automatically rewind or fast

forward to the “00:00:00” counter posi-

tion.

Repeat playback

The entire video tape will play until its end. The tape will

automatically rewind to the beginning and the playback will

be repeated.

Zero return function

COUNTER RESET

PLAY

VCR MENU

SET +/–

ENTER

STOP

ZERO RETURN

CLOCK/COUNTER

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

PLAY

CLOCK/COUNTER

COUNTER RESET

ANGLE

ZERO RETURN

JUMP

CALL

2C53601A (E)p32-37 3/10/04, 11:3232

Playback (VCR)

This function enables you to locate the beginning of any recording

made on the VCR.

Recording an INDEX mark

The Index Search function auto-

matically records an INDEX mark

on the tape whenever a recording

is initiated.

Index search

Press INDEX + or – during stop or play mode.

For Succeeding programs: Press INDEX +.

For Preceding programs: Press INDEX –.

(As many as 9 index points can be accessed via this

method.)

When the INDEX + or – is pressed,

the unit starts searching the INDEX

NO. selected and finds the portion,

then playback starts automatically.

To stop the Index Search, press

STOP.

CH 001

INDEX

SQPB (S-VHS Quasi Playback)

You can playback video cassette tapes recorded in the

S-VHS system.

However, the picture will not have the high resolution of

S-VHS system.

Note: You cannot record S-VHS video format with this VCR.

Notes:

• When you record an INDEX mark at the very beginning of the

tape, the mark may not be found.

• During INDEX search, the tape may stop and begin to play at a

slightly different location.

• INDEX may not function properly with old or worn out video tapes.

• INDEX marks may not be found if it is extremely close to the point

where the search began.

• In recording, if you stop recording temporarily, the INDEX mark

is not recorded on the tape.

Video index search system

Press CLOCK/COUNTER. The clock and tape counter

alternate with each other in the display window.

Notes:

• If you rewind the tape beyond “00:00:00”, a minus sign (“–”)

will be displayed in front of the time.

• When you load a tape, the counter will reset to “00:00:00”.

• The counter does not function on nonrecorded (blank)

sections of the tape. When you rewind, fast forward or play

tapes through blank sections, the counter stops.

Clock/counter display

COUNTER

CLOCK

Press VCR DVD selector. The DVD mode and the

VCR mode alternate with each other in the display.

DVD mode

VCR mode

INDEX NO. (up to 9)

or is displayed

STOP

VCR DVD

INDEX

–

CLOCK/COUNTER

INDEX

SKIP

–

INDEX

SKIP

VCR

DVD

2C53601A (E)p32-37 3/10/04, 11:3233

Recording (VCR)

Recording a TV program

Recording and viewing the same TV program.

Recording a TV program

Load a cassette tape with the erase prevention

tab intact.

The DVD/VCR will automatically turn on.

00 : 00 : 00 SP

CH 110

INDEX

Press SP/SLP to select the desired tape speed

SP or SLP.

The tape counter and “SP” or “SLP”

will appear on the screen for about 4

seconds.

Select “TV” or “CATV” to the appropriate

position

TV - VHF/UHF channels

CATV - CABLE TV channels

Press Number buttons or CH +/– to select the

channel to be recorded.

Press REC/OTR.

“ ” will appear on the screen

for about 4 seconds and “REC” will

appear on the display window.

VHF/UHF/CATV CHANNELS

TV CATV

VHF

2-13

UHF

14-69

VHF

2-13

STD/HRC/IRC

14-36 (A) (W)

37-59 (AA) (WW)

60-85 (AAA) (ZZZ)

86-94 (86) (94)

95-99 (A-5) (A-1)

100-125 (100)(125)

01 (5A)

TV mode direct channel selection:

All channels can be instantly selected by using two

buttons. (for example, to select channel 2, press “0”, then

“2”. If you press only “2”, channel selection will be delayed

for two seconds.) For channels 10 and above, press the 2

digits in order.

CATV mode direct channel selection:

1-9 Press 0 twice and then 1-9 as required.

Example: To select “2”, Press 002.

10-12 Press 0 first and then the remaining 2 digits in

order from left to right.

Example: Press 012 for “12”.

13-99 Press 2 digits in order.

Example: Press 22 for “22”.

100-125 Press the 3 digits in order.

Example: Press 110 for “110”.

654

321

VCR DVD

SP/SLP

PLAY MODE

SET

–

ENTER

REC/OTR

Preparation:

• Turn ON the TV and select to the corresponding

video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

2C53601A (E)p32-37 3/10/04, 11:3234

Recording (VCR)

Recording one program while

watching another

Press STOP to stop recording.

“ ” will appear on screen for about

4 seconds.

Press PAUSE/STILL to avoid recording unwanted

material. Press again to continue the recording.

“ ” will appear on screen for

about 4 seconds.

Notes:

•

The pause function will be released after 5 minutes to prevent

damage to the tape or the VCR. The VCR will change to the

STOP mode.

• You can select a recording channel in the recording pause

mode.

To stop recording temporarily

While the VCR is recording, select your desired channel

on the TV.

When a TV is connected with an antenna cable only,

press TV/VCR to select the TV position.

The “VCR” display will go off and recording will continue.

Select the TV channel you want to watch by using the

TV channel selector.

Note:

Some CATV hookups do not permit viewing one channel

while recording another. See pages

and

This VCR will automatically rewind the tape when the tape

has ended (except during OTR and timer recording). It will

also eject the tape.

Auto Rewind feature

To stop recording

TV/VCR

STOP

PAUSE/STILL

2C53601A (E)p32-37 3/10/04, 11:3235

Recording (VCR)

One-touch Timer Recording (OTR)

The One-touch Timer Recording feature provides a simple and

convenient way to make a timed recording.

One-touch Timer Recording (OTR)

Press

once

twice

3 times

4 times

5 times

NORMAL REC

0:30

1:00

1:30

2:00

3:00

4:00

5:00

6:00

NORMAL REC

Recording time

Press

6 times

7 times

8 times

9 times

10 times

Recording time

Load a cassette tape with the erase

prevention tab intact.

The VCR will automatically turn on.

Press SP/SLP to select the desired tape speed

SP or SLP.

The tape counter and “SP” or “SLP”

will appear on the screen for about 4

seconds.

Set “TV” or “CATV” option to the appropriate

position

00 : 00 : 00 SP

CH 110

INDEX

OTR 0 : 30

TV - VHF/UHF channels

CATV - CABLE TV channels

Press Number buttons or CH +/– to select the

channel to be recorded.

Press

REC/OTR

. Recording begins. Press the

button again to stop recording after 30 minutes.

Each additional press of

REC/OTR

will increase

recording time as shown in the chart below, up

to a maximum of 6 hours.

The OTR and recording time will

appear on the screen for about 4

seconds. And, “ ” will appear on

the display.

To cancel OTR

Press STOP or turn off the power.

“ ” will appear on screen for about 4 seconds.

Note:

If you wish to watch the DVD playback during OTR or standard

recording, press VCR DVD selector to change to DVD mode and

perform the DVD playback

VCR DVD

STOP

654

321

SP/SLP

PLAY MODE

SET

–

ENTER

REC/OTR

Preparation:

• Turn ON the TV and select to the corresponding

video input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

Example: One-touch Timer Recording for 30 minutes.

2C53601A (E)p32-37 3/10/04, 11:3236

Recording (VCR)

Timer recording

Timer recording can be programmed on-screen with the remote control.

The built-in timer allows automatic unattended recording of up to 8

programs within 1 month.

Timer recording

Notes:

• Press CANCEL to move cursor backward for correction.

• To record from external source set the channel to “L1” or

“L2”.

Notes:

• If the timer symbol ( ) blinks when the timer recording ended,

the TV program has not been completely recorded because of

an insufficient tape length. Press TIMER REC to cancel the

timer program or press EJECT to remove the cassette tape.

• During timer recording standby mode, the VCR mode cannot be

operated. To use the VCR, press TIMER REC at first, then press

VCR DVD selector to change to VCR mode. After you use the

VCR, press TIMER REC again to put the VCR into timer

recording standby mode.

• If you press TIMER REC during timer recording, the recording

operation will be interrupted. If you press TIMER REC again

within the programmed time, the recording operation will start

again.

• After a power failure or disconnection of the power plug, all

programmed recording settings and time display will be lost

upon resumption of power. In this case, reset the clock

and

reprogram any timer recording.

Press VCR MENU. Select “TIMER REC SET”,

then press ENTER.

Preparation:

• Press VCR DVD selector to select the VCR mode.

• Load a cassette tape with the erase prevention tab

intact.

• Check the time and date are correct

Example: Program a timer recording for the 26th day,

channel 125

(CATV), 11:00 - 11:30 PM on timer program

number 1 (Tape speed: SLP).

Press SET + or – to select one of the program

line, then press ENTER.

Press SET + or – to select the date, then press

ENTER.

Set the start time, end time, channel and tape

speed as in step 3.

To enter other programs, repeat step 2

through 4.

• To return to the normal screen,

press VCR MENU twice.

Press TIMER REC. The timer symbol ( ) will

appear on the display and the VCR stands by

for recording.

At the same time, VCR mode will

change to DVD mode automatically.

You can use DVD even if the VCR is

in the timer recording mode.

If you do not use the DVD, turn the

power off.

Notes:

• The timer recording will start at 5 seconds before the time

you predetermined.

• If the timer symbol( ) does not appear on the display in

spite of the pressing of TIMER REC, the cassette may not

have been loaded.

• If the cassette is ejected in spite of the pressing of TIMER

REC, the erase prevention tab of the cassette may have

been removed.

2,3

1–3

VCR DVD

TIMER REC

CANCEL

1,5

EJECT

SET

–

ENTER

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

TIMER REC

2C53601A (E)p32-37 3/10/04, 11:3237

Recording (VCR)

Setting procedure

To set daily/weekly timer

To confirm Timer program:

At step 1 on the previous page select “TIMER REC

SET” and press ENTER.

The timer program list will appear on the screen.

The current day (Friday) SU-SA (Sunday to Saturday)

MO-SA (Monday to Saturday)

MO-FR (Monday to Friday)

WKL-WE WKL-TH (Weekly Thursday)

(Weekly Wednesday)

One month later

minus one day

Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g. MO-

SA: Monday to Saturday) Timer recording

Follow the procedure of timer recording on the previous

page. At step 3 press SET + or – repeatedly until the

desired setting appears. Then press ENTER.

When you press SET – repeatedly, the

DATE indicator will change as follows, in

this case the day is Friday.

If the programs overlap another

Do not overlap timer programs as portions of the

conflicting programs will be lost. The first recording

time has priority over the next recording time as shown

in the diagram below.

Notes:

• The daily/weekly recording can be made continuously until the

recording is canceled or the tape reaches the end.

• During timer recording the automatic rewinding mechanism

does not function.

8 : 00

11 : 00

9 : 00

10 : 00

Program 1

Prog.1

Deleted Parts

Non Recorded Portion Parts

Prog.2 Prog.3

Program 2

Program 3

Recording

Control Settings

–

/ENTER/CANCEL/MENU

DATE START END CH

WKL-WE

–

/ENTER/CANCEL/MENU

DATE START END CH

26(SU)

:00

:30

125

SLP

Notes:

• If there are other timer record programs remaining, TIMER

REC must be pressed to reactivate the timer, otherwise the

remaining timer record programs will be ignored.

• You cannot confirm the Timer program during timer recording

operation.

• You can correct or cancel a programmed setting in program

confirm mode.

If the Timer has been activated, press TIMER

REC to deactivate the Timer.

The timer symbol ( ) will

disappear. Then press VCR DVD

selector to change to VCR mode.

To cancel Timer program:

Press SET + or – to select the unwanted program,

then press CANCEL to cancel the program.

Press VCR MENU repeatedly until the menu

screen is cleared.

Timer recording (continued)

To confirm or cancel a program

SET +/–

ENTER

VCR MENU

CANCEL

VCR DVD

TIMER REC

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

CANCEL

VCR

DVD

2C53601A (E)p38-41 3/10/04, 11:3238

Other functions (VCR)

Stereo recording and playback /

Second Audio Program (SAP)

When a MTS STEREO broad-

cast is received, “STEREO” will

appear on the screen for about 4

seconds and the program can

be viewed or recorded in stereo.

The Hi-Fi stereo recording pro-

cedure is the same as for normal

recordings.

Notes:

• When playing back a tape that is not recorded in Hi-Fi stereo

mode, the audio will automatically be monaural.

• When listening to a VHS Hi-Fi video tape or MTS broadcast

through the VHF/UHF jack (Audio/Video cable not connected),

the sound will be monaural.

When viewing an MTS stereo TV program, or playing a

prerecorded VHS Hi-Fi stereo videotape, press AUDIO

SELECT to select how the audio will be heard through

the speakers. Normally set to the Hi-Fi stereo position,

this button can be set to the MONO position if the stereo

broadcast or videotape audio is of poor quality. The “R”

and “L” positions allow the audio from the Right or Left Hi-

Fi channel to be heard over both TV speakers. This

button has no effect when viewing a MONO videotape or

TV program. Each time when you press the button,

OUTPUT SELECTION display appears on the screen for

several seconds. Refer to the chart below.

Output selection

Your DVD/VCR is fitted with a SAP broadcast system which

enables you to switch to a second audio program when

viewing a selected channel.

This function applies only when the program is broadcast

in multi-languages through the SAP broadcast system.

When the VCR is turned on or a channel selection is

made, make certain the letters “SAP” appears on the

screen for about 4 seconds. This means that the “Second

Audio Program” broadcasting is available.

Listening to SAP

Stereo recording and playback

The VHS Hi-Fi audio system permits high fidelity record-

ing of MTS STEREO TV broadcasts.

Second Audio Program (SAP)

OUTPUT

SELECTION

STEREO

L CH

R CH

MONO

SOUND HEARD ON BOTH

SPEAKERS

STEREO

LEFT CHANNEL AUDIO

RIGHT CHANNEL AUDIO

MONO

Press VCR MENU. Then press SET + or – to

select “SAP”.

Press ENTER to select “ON”.

Then press VCR MENU until the

menu screen is cleared.

STEREO SAP SAP

SET +/–

ENTER

CANCEL

VCR MENU

Other functions (VCR)

Note:

When using a CATV system, stereo TV programs may be

transmitted over a mono cable channel. In this case

“STEREO” will not appear and the sound will be in mono.

AUDIO SELECT

AUDIO

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

VCR MENU

SETUP

2C53601A (E)p38-41 3/10/04, 11:3339

Other functions (VCR)

To AUDIO (L) OUT

AUDIO/VIDEO cable (supplied)

Playback VCR

To VIDEO OUT To AUDIO (R) OUT

Recording VCR

To AUDIO (L) IN

To VIDEO IN

To AUDIO (R) IN

Duplicating a video tape

If you connect the DVD/VCR to another VCR or Camcorder, you can duplicate

a previously recorded tape. Make all connections before turning on the power.

Duplicating a video tape

For duplicating a previously recorded tape from a

camcorder, follow the camcorder manufacturer’s

instructions. A typical camcorder dubbing hookup is

shown above.

AUDIO/VIDEO cable (not supplied)

To AUDIO (R) IN

To AUDIO (L) IN

To VIDEO IN

Recording VCR

To AV Jack

Playback Camcorder

Connection with second VCR

Connection with Camcorder

Press SP/SLP to select the desired tape speed

SP or SLP.

It is recommended that you set the

tape speed to the SP mode on the

recording VCR for best results.

Press INPUT SELECT once or twice to select

AUDIO/VIDEO input position.

“L1” or “L2” will appear in the display.

Press REC/OTR on the recording VCR.

The duplicating process begins.

Press PLAY on the playback VCR or Camcorder.

Press STOP after duplicating a video tape.

L1: on the rear panel

L2: on the front panel

Preparation:

• Turn ON the TV and select the corresponding video

input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

• Load a cassette tape with the erase prevention tab

intact.

• Load a previously recorded tape into the playback

VCR or Camcorder.

VCR DVD

SP/SLP

PLAY MODE

INPUT SELECT

PROGESSIVE

REC/OTR

2C53601A (E)p38-41 3/10/04, 11:3340

Other functions (VCR)

Press REC/OTR to start recording.

The DVD/VCR will change to the

VCR mode automatically and the

playback picture or sound will be

duplicated on the video cassette

tape.

Recording a DVD/CD disc

You can record disc material in DVD, Audio CD, etc. onto a Video

tape with this DVD/VCR.

Duplicating a DVD or CD disc

Press SP/SLP to select the desired tape speed

SP or SLP.

Preparation:

• Turn ON the TV and select the corresponding video

input.

• Press VCR DVD selector to select the VCR mode.

(The VCR indicator will light.)

•

Load a cassette tape with the erase prevention tab intact.

• Load a DVD/CD disc.

Press VCR DVD selector to select the DVD mode.

The DVD indicator will light.

Press PLAY to start playback.

Press STOP if you finish recording.

If you wish to stop a DVD/CD disc,

press VCR DVD selector to change

the DVD mode, then press STOP.

Notes:

• You may not be able to record the beginning of the disc.

Begin VCR recording once program playback commences

on the DVD.

• When the scanning mode is set to the progressive mode,

you cannot duplicate a disc material onto a video tape.

When REC/OTR is pressed, the PROGRESSIVE indicator

“ ” on the display window will flash and “Please Set

Off” will appear on the screen.

• You can not record discs encoded with copy guard

function. The following icon and text will show up on the

TV screen.

DISC IS COPY PROTECTED

00 : 00 : 00 SP

SP/SLP

PLAY MODE

VCR

DVD

PLAY

REC/OTR

2C53601A (E)p38-41 3/10/04, 11:3341

Press OPEN/CLOSE or PLAY on the unit.

The disc tray closes automatically.

On the TV-screen, “ ”

changes to

“Reading” and then playback

commences.

• A menu screen will appear on the TV screen, if

the disc has a menu feature.

Press / or / to select title.

Press ENTER.

• Title is selected and play

commences.

Press STOP to end playback.

• The unit records the stopped point,

depending on the disc. “

”

appears on the screen. Press

PLAY

to resume playback (from

the scene point).

• If you press STOP again or unload

the disc (“

” appears on the

screen.), the unit will clear the

stopped point.

Reading

Playing a disc

This section shows you the basics on how to play a disc.

CAUTION

Keep your fingers well clear of the disc tray as it is closing.

Neglecting to do so may cause serious personal injury.

Basic playback

Preparations:

• When you want to view a disc, turn on the TV and select the corresponding video input connected to the DVD/VCR. This

may include S-video or component video inputs which are exclusive to DVD playback.

• When you want to enjoy the sound of discs from the audio system, turn on the audio system and select the input

connected to the DVD/VCR.

Press ON/STANDBY (I / ).

The DVD/VCR turns on.

Press VCR/DVD SELECT to select the DVD mode.

The DVD indicator will light.

Press OPEN/CLOSE.

The disc tray opens.

Place the disc on the disc tray.

With the playback

side down

• There are two different disc sizes. Place the disc

in the correct guide on the disc tray. If the disc is

out of the guide, it may damage the disc and

cause the DVD/VCR to malfunction.

• Do not place a disc which is unplayable in this

DVD/VCR.

DVD

VCD

Display window STOP PLAY

To start playback in the stop mode

Press PLAY.

Basic playback (DVD)

SET

–

ENTER

SET

–

ENTER

2C53601A (E)p42-45 3/10/04, 11:3342

Basic playback (DVD)

To pause playback (still mode)

Press PAUSE/STILL during playback.

To resume normal playback, press

the PLAY button.

• The sound is muted during still

mode.

To stop playback

Press STOP.

To remove the disc

Press OPEN/CLOSE.

Remove the disc after the disc tray

opens completely.

Be sure to press the OPEN/CLOSE button to close

the disc tray after you remove the disc.

Playing a Disc while the VCR section is recording

or standing by for timer recording

1) Start to record.

Follow steps 1~5 on page 34.

• If the DVD/VCR is standing by for recording, turn on

the DVD/VCR.

2) Press VCR DVD selector to select DVD mode. The

DVD indicator will light.

3) Play a disc.

Follow steps 3 ~ 5 on page 42.

• Press PLAY if the DVD/VCR does not start to play a

disc automatically.

4) Stop to play.

Press STOP to stop play back a disc.

Notes:

• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen

according to the type of loaded disc. In this case, check your disc again (See pages 8 and 61).

• Some discs may take a minute or so to start playback.

• When you set a single-faced disc label downwards (ie. the wrong way up) and press the OPEN/CLOSE button or the PLAY

button on the unit, “Reading” will appear on the display for 30 seconds and then “Incorrect Disc” will continue to be displayed.

• Some discs may not work the resuming facility.

• Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see above.

• Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according

to the disc contents the software producers designed, some playback features may not be available. Also refer to the

instructions supplied with the DVDs.

• Do not move the DVD/VCR during playback. Doing so may damage the disc.

• Use the OPEN/CLOSE button to open and close the disc tray. Do not push the disc tray while it is moving. Doing so may

cause the DVD/VCR to malfunction.

• Do not push up on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD/VCR to

malfunction.

• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen

menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press the

ON/STANDBY (I / ) button on your remote control once the movie is completed.

• There may be a slight delay between you pressing the button and the function activating.

To obtain a higher quality picture

Occasionally, some picture noise not usually visible during a normal broadcast

may appear on the TV screen while playing a DVD video disc because the high

resolution pictures on these discs include a lot of information. While the amount of

noise depends on the TV you use with this DVD/VCR, you should generally

reduce the sharpness adjustment on your TV when viewing DVD video discs.

About

The icons on the heading bar show the playable discs for the

function described under that heading.

: You can use this function with DVD video discs.

: You can use this function with Video CDs.

: You can use this function with Audio CDs and CD-R/RW CDs.

OPEN/CLOSE

STOP

PAUSE/STILL

VCR DVD

PLAY

Screen saver function

The screen saver operates when you leave the unit in

DVD stop mode for about five minutes.

The screen will repeatedly get dark gradually and back

to normal.

To turn off the PBC

Press number button 1 in the stop mode, then press

ENTER.

ENTER

2C53601A (E)p42-45 3/10/04, 11:3343

FWD

Playing a disc (continued)

You can play discs at various speeds.

Playing frame by frame

REW

PLAY

PAUSE/STILL

SKIP /

SLOW

Basic playback (DVD)

DVD

VCD

DVD

VCD

REW

FWD

SLOW

PLAY

INDEX

SKIP

INDEX

SKIP

–

Playing in fast reverse or fast forward directions

Press REW or FWD during playback.

REW: Fast reverse playback

FWD: Fast forward playback

Each time you press the REW or

FWD button, the playback speed

changes.

To resume normal playback

Press PLAY.

Notes:

• The DVD/VCR mutes sound and subtitles during reverse

and forward scan of DVD video discs. However, the DVD/

VCR plays sound during fast forward or fast reverse play

of audio CDs.

• The playback speed may differ depending on the disc.

Press PAUSE/STILL during still playback.

Each time you press the PAUSE/

STILL button, the picture advances

one frame.

To resume normal playback

Press PLAY.

Note:

The sound is muted during frame by frame playback.

Press SLOW during playback.

Each time you press the SLOW

button, the slow-motion speed

changes.

To resume normal playback

Press PLAY.

Note:

The sound is muted during slow-motion playback.

Press SKIP or repeatedly to display the chapter or track number you want.

Playback starts from the selected chapter or track.

To locate succeeding chapters or

tracks.

Playback starts from the beginning of

the current chapter or track.

When you press twice in quick successions,

playback starts from the beginning of

the preceding chapter or track.

• A “Prohibition” symbol may appear at the upper left of the screen. This symbol means either the feature you tried is not

available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate a problem with the DVD/

VCR.

• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave

the still video image or On screen display image displayed on your TV for an extended period of time, you risk permanent

damage to your television screen. Projection televisions are very susceptible.

Notes:

Locating a chapter or track

Playing in slow-motion

DVD

VCD

DVD

VCD

2C53601A (E)p42-45 3/10/04, 11:3344

Basic playback (DVD)

Reading

Advanced playback (DVD)

ENTER

PLAY

OPEN/CLOSE

STOP

MP3/WMA playback

MP3/WMA/JPEG CD Information

654

321

▲ / ▼ / /

/72

--:--

/0-9/Enter/Play Mode

Japan

CD-R

Bay Bridge

CLOSE MY EYES

DIVE TO BLUE

Honey

flower

Lies and Truth-

winter fall

Rain

Strawberry

BLUE EYES

Welcome party

Blurry Eyes

Thailand

Pops

/0-9/Enter/Play Mode

/72

Japan

CD-R

Bay Bridge

CLOSE MY EYES

DIVE TO BLUE

Honey

flower

Lies and Truth-

winter fall

Rain

Strawberry

BLUE EYES

Welcome party

Blurry Eyes

Thailand

Pops

--:--

/0-9/Enter/Play Mode

/72

Mother

CD-R

Hold Your Last

Pops

--:--

PLAY

SET

–

ENTER

SET

–

ENTER

PLAY

Advanced playback (DVD)

Limitations on display

• The maximum number for display is 16 letters. Available

letters for display are the following: capital or small

alphabets of A through Z, numbers of 0 through 9, and _

(under score).

• Other letters than those above are replaced in hyphen.

Notes on MP3/WMA/JPEG files

To play back MP3/WMA/JPEG CD in the recorded order,

1. Use MP3/WMA/JPEG software that records data

alphabetically or numerically.

2. Name each file including two-digit or three-digit number

(e.g. “01” “02” or “001” “002”).

3. Refrain from making too many sub-folders.

WMA disc compatibility with this player is limited as follows:

1) Sampling Frequency: within 32 -- 48 kHz

2) Bit Rate: within 48 -- 192kbps.

Mono WMA files and WMA files (under 48kbps) cannot

be played back on this player.

CAUTION:

• Some MP3/WMA/JPEG CDs can not be played back

depending on the recording conditions.

• The CD-R/RW that has no music data or non-MP3/WMA/

JPEG files can not be played back.

Press STOP to end playback.

MP3/WMA/JPEG playback

This player can play back the MP3/WMA/JPEG-data which has been recorded

on CD-R or CD-RW. To produce the MP3/WMA/JPEG-data, you need a

Windows-PC with CD-ROM drive and a MP3/WMA/JPEG-encoding Software

(not supplied).

The Apple-HFS-System can not be played.

Limitations on MP3/WMA/JPEG CD playback

• MP3/WMA/JPEG CD is the disc that is standardized by

ISO9660, its file name must include 3-digits extension

letters, “mp3”, “wma”, “jpg”.

• The directory and file names of the MP3/WMA/JPEG CD

must be correspond to the ISO standardized files.

• This unit can read 200 files per disc. If a disc has more than

200 files, it reads up to 200 files, the remaining files will be

omitted.

• The unit is able to recognize up to a maximum of 50

directories per disc.

• MP3/WMA CDs cannot be used for playback for the

purpose of recording.

• If the CD has both audio tracks and MP3/WMA/JPEG files,

only audio tracks are played.

• It may take more than one minute for this unit to read MP3/

WMA/JPEG files depending on its structure.

• Music recorded by “Joliet Recording Specification” can be

played back, the file name is displayed (within 16 letters) on

the screen. Long file names will be condensed.

• The music files recorded by “Hierarchical File System”

(HFS) cannot be played.

• The unit can play back baseline and progressive JPEG files.

Press OPEN/CLOSE.

The disc tray will open.

Place a disc on which MP3

or WMA files have been

recorded onto the tray.

Press OPEN/CLOSE or PLAY.

The disc tray closes automatically.

On the TV-screen,“Reading” will appear.

Reading will take as

much time as the

number of file.

A file menu screen will appear on the TV screen.

Press or to select folder.

Press / or / or Number keys to select

the desired file, then press ENTER.

The file is selected and play commences.

• In case the folder includes more than

15 tracks, press or to display

next file list.

• When PLAY has been pressed after

displaying the file menu, or when the

disc tray has been closed after pressing

PLAY in step 2, playback begins

automatically starting from the first file.

In this case, if the first file is an MP3/

WMA file, only MP3/WMA files are

played back in order.

If the first file is a JPEG file, the first

JPEG file is played back.

0–9

• The unit records the stopped point.

“ ” appears on the screen. Press

PLAY to resume playback (from the

scene point).

• If you press STOP again or unload the

disc, the unit will clear the stopped point.

2C53601A (E)p42-45 3/10/04, 11:3345

Press OPEN/CLOSE.

The disc tray will open.

Place a disc on which

JPEG files have been

recorded onto the tray.

Press OPEN/CLOSE or PLAY.

The disc tray closes automatically.

On the TV-screen, “Reading” will appear.

Reading will take

as much time as

the number of file.

A file menu screen will appear on the TV screen.

Press or to select folder.

Press / or / or Number keys to select

the desired file.

To display a picture menu, press MENU.

(To return to a file menu, press TOP MENU.)

Press / or / to select the desired file.

• To display next list, press SKIP or .

• When PLAY has been pressed after displaying the

file menu, or when the disc tray has been closed

after pressing PLAY in step 2, playback begins

automatically starting from the first file. In this

case, if the first file is a JPEG file, the first JPEG

file is played back. If the first file is an MP3/WMA

file, only MP3/WMA files are played back in order.

Reading

MP3/WMA/JPEG playback (continued)

You can select your desired JPEG file on the file menu and picture menu.

The selected JPEG file is automatically adjusted to the TV screen. (When the

aspect ratio of the JPEG file is different to your TV screen, the black bar will

appear at the top and bottom, or the both sides of the TV screen.

Advanced playback (DVD)

ENTER

▲ / ▼ /

STOP

PLAY

0–9

SKIP

OPEN/CLOSE

TOP MENU

JPEG CD playback

Press ENTER.

The selected picture appears on the TV

screen.

Press STOP to end playback.

The file menu appears on the TV

screen.

If you want to watch the other file,

repeat steps 4~5.

/36

Pic-1

CD-R

Pic-2

Pic-3

Pic-4

Pic-5

Pic-8

Pic-9

Pic-10

Pic-11

Pic-12

Pic-6

Pic-13

Pic-7

Pic-14

Collection

/0-9/Enter/Play Mode/Menu

/36

Pic-1

CD-R

Pic-2

Pic-3

Pic-4

Pic-5

Pic-8

Pic-9

Pic-10

Pic-11

Pic-12

Pic-6

Pic-13

Pic-7

Pic-14

Collection

/0-9/Enter/Play Mode/Menu

Notes:

• The picture menu is displayed when the FUJICOLOR CD or

the Kodak Picture CD are played. To display the file menu

press TOP MENU.

• During MP3/WMA/JPEG-Playback, you can not use SEARCH,

A-B Repeat functions.

• You can use Repeat (Track or All), Random functions and

Program playback for MP3/WMA/JPEG CD Playback. (See

pages 52 and 53.)

• In the case of a CD containing a mixture of MP3, WMA and

JPEG files, the files are played back by selecting them from the

file menu.

Operation

Media type

Folder

File number

Elapsed time

: Indicates MP3 file

: Indicates WMA file

: Indicates JPEG file

/Menu

File menu information

PLAY

654

321

SET

–

ENTER

TOP MENU

SET

–

ENTER

Microsoft, Windows Media, and Windows Logo are

trademarks or registered trademarks of Microsoft

Corporation in both the United States and other countries.

2C53601A (E)p46-47 3/10/04, 11:3346

Basic playback (DVD)

Setting the JPEG Interval

Press SETUP in the stop mode. Press or to

select “Picture”, then press ENTER.

Press or to select “JPEG Interval”.

Press ENTER or / to select your desired time.

Off:

Plays back one file at a time.

5 Seconds:

Plays back images in the form of a slide show at 5

second intervals.

10 Seconds:

Plays back images in the form of a slide show at 10

second intervals.

15 Seconds:

Plays back images in the form of a slide show in 15

second intervals.

To make SETUP screen disappear, press SETUP.

ENTER

▲ / ▼ /

SETUP

/Enter/Setup/Return

Language Picture Parental OtherSound

Tv Screen

Display

JPEG Interval

Select Files

/Enter/Setup/Return

Language Picture Parental OtherSound

Off

All

4:3

E.B.L.

Tv Screen

Display

JPEG Interval

Select Files

All

/Enter/Setup/Return

Language Picture Parental OtherSound

5 Seconds

4:3

Off

E.B.L.

You can continuously play back all JPEG files automatically.

After the setting below, start playing the disc on which JPEG files have been recorded.

SET

–

ENTER

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

Advanced playback (DVD)

2C53601A (E)p46-47 3/10/04, 11:3347

Setting the Select Files

Press SETUP in the stop mode.

Press

or to select “Picture”, then press

ENTER.

Press or to select “Select Files”.

Press ENTER or / to select your desired

file type.

All:

Displays all files.

Music Only:

Displays only MP3/WMA files.

Pictures Only:

Displays only JPEG files.

To make SETUP screen disappear, press

SETUP.

Advanced playback (DVD)

MP3/WMA/JPEG playback (continued)

/Enter/Setup/Return

Language Picture Parental OtherSound

Tv Screen

Display

JPEG Interval

Select Files

4:3

/Enter/Setup/Return

Language Picture Parental OtherSound

Off

All

Off

E.B.L.

Tv Screen

Display

/Enter/Setup/Return

Language Picture Parental OtherSound

JPEG Interval

Select Files

Off

Pictures Only

4:3

Off

E.B.L.

ENTER

▲ / ▼ /

SETUP

When playing back a CD containing a mixture of MP3, WMA and JPEG files, only MP3/WMA or JPEG files can be displayed on

the file menu.

SET

–

ENTER

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

2C53601A (E)p48-49 3/10/04, 11:3348

Basic playback (DVD)

Zooming (JPEG CD)

Press ZOOM during playback.

Enlarged JPEG images are displayed.

You can make the images even larger

by repeatedly pressing ZOOM.

Changing angles (JPEG CD)

ANGLE

ZOOM

This unit will allow you to zoom in on the JPEG image.

Off

Press ANGLE during playback.

Images are rotated 90 degrees to the right.

Press ANGLE repeatedly until the desired

angle is selected.

Pressing ANGLE four times returns the image

to its original angle.

• Images are displayed at the

same angle until the disc is

removed.

You can display JPEG images rotating at 90 degree intervals.

Press / / / to view a different part of the

frame.

You may move the frame from the

centre position to UP, DOWN, LEFT or

RIGHT direction.

In the zoom mode press ZOOM repeatedly to

return to a 1:1 view (

Off).

▲ / ▼ / /

CM SKIP

ZOOM

COUNTER RESET

ANGLE

SET

–

ENTER

CM SKIP

ZOOM

COUNTER RESET

ANGLE

Advanced playback (DVD)

2C53601A (E)p48-49 3/10/04, 11:3349

Zooming

Press ZOOM during playback.

The centre part of the image will be

zoomed in.

Each press of ZOOM will change the

ZOOM 1 (x 1.3), 2 (x 1.5) and 3

(x 2.0).

▲ / ▼ / /

Zooming/Locating desired scene

Advanced playback (DVD)

DVD

VCD

This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the

frame.

Press / / / to view a different part of the

frame.

You may move the frame from the

centre position to UP, DOWN, LEFT or

RIGHT direction.

In the zoom mode press ZOOM repeatedly to

return to a 1:1 view ( Off).

Notes:

• You can select the Pause, Slow or Search playback in the zoom mode.

• Some discs may not respond to zoom feature.

ZOOM

CANCEL

0–9

ENTER

JUMP

DISPLAY

Locating desired scene

DVD

VCD

Use the title, chapter and time recorded on the disc to locate the desired point to play back.

To check the title, chapter and time, press DISPLAY.

Press JUMP during playback or stop mode.

Press or to select the “Time”, “Title” or

“Chapter”.

Press Numbered buttons (0–9) to change the

number.

• If you input a wrong number, press

CANCEL.

• Refer to the package supplied with

the disc to check the numbers.

Press ENTER. Playback starts.

• When you change the title,

playback starts from Chapter 1

of the selected title.

• Some discs may not work in the

above operation.

654

321

Note:

In case of the Video-CD playback with PBC, the JUMP does not work. To turn off PBC, see page

CM SKIP

ZOOM

SET

–

ENTER

CM SKIP

ZOOM

ZERO RETURN

JUMP

SET

–

ENTER

SET

–

ENTER

2C53601A (E)p50-53 3/10/04, 11:3450

Basic playback (DVD)

Returning to the scenes

DVD

VCD

Marking the scenes

DVD

VCD

Press MARKER during playback.

Select the blank Marker using or .

Then press ENTER at the desired scene.

• Repeat this procedure to set

the other 2 scenes.

Press MARKER to remove this display.

Press MARKER during playback or stop mode.

Press or to select the Marker 1-3.

Press ENTER.

Playback starts from the marked

scene.

Marking desired scenes

The unit stores the points that you want to watch again up to 3 points.

You can resume playback from each scene.

Notes:

Some discs may not work with the marking operation.

The marking is canceled when you

open the disc tray or turn

the power off.

Some subtitles recorded around the marker may fail to

appear.

•

ENTER

CANCEL

To cancel the Marker

Follow the above steps 1~2, then press CANCEL.

MARKER

SET

–

ENTER

SET

–

ENTER

▲ / ▼

SET

–

ENTER

Advanced playback (DVD)

2C53601A (E)p50-53 3/10/04, 11:3451

Repeat playback of Title, Chapter and Track

Press PLAY MODE during playback or stop mode.

DVD

Press

/ or ENTER once or twice to select

“Chapter” or “Title”.

ENTER

▼ /

Repeat playback/A-B Repeat playback

CD/VCD

Press

to select “Repeat”.

Press

/ or ENTER once or twice to select

“Track” or “All”.

Press PLAY MODE again to make the screen

disappear.

Press PLAY to start Repeat playback.

To resume normal playback, select Repeat “Off”.

Note:

Some discs may not work with the repeat operation.

A-B Repeat playback

Press A-B RPT during playback.

The start point is selected.

Press A-B RPT again.

The end point is selected. Playback

starts at the point that you selected.

Playback stops at the end point, re-

turns to Point A automatically, then

starts again.

A-B repeat playback allows you to repeat material between

two selected points.

PLAY MODE

A-B RPT

Advanced playback (DVD)

Repeat

/Enter/Play Mode

Off

Chapter

Repeat

/Enter/Play Mode

Repeat

Title

/Enter/Play Mode

Play Mode Off

Repeat Off

/Enter/Play Mode

Track

Play Mode Off

Repeat

/Enter/Play Mode

Repeat

Play Mode Off

All

/Enter/Play Mode

DVD

VCD

Notes:

• In A-B repeat mode, subtitles near point A or B may not

appear.

• A-B Repeat playback is not available in multi-angle scenes.

• A-B Repeat playback does not work when Repeat playback

is on.

• You may not be able to set A-B Repeat, depending on the

scenes of the DVD.

• A-B repeat does not work with an interactive DVD, MP3/

WMA/JPEG CD and Video CD with PBC.

To resume normal playback

Press A-B RPT again.

“

Off

” appears on the screen.

DVD

VCD

SP/SLP

PLAY MODE

SET

–

ENTER

SET

–

ENTER

A-B RPT

2C53601A (E)p50-53 3/10/04, 11:3452

Basic playback (DVD)

SET

–

ENTER

Program playback

Press PLAY MODE in the stop mode.

Press or to select Play Mode, then press

/ or ENTER to select “Program”.

Press / or / to select the programming

position. Use Numbered buttons (0–9) to input

the Track numbers.

• To program others, repeat Step 3.

• If you input a wrong number, press

CANCEL.

Press / or / to select “Program

Playback”

and press ENTER.

The programmes you selected will start

to playback in the order.

To return to normal playback, select

Play Mode: “Off”.

To cancel program playback

Select “Clear” and press ENTER.

• The program is canceled when

you open the disc tray or turn the

power off.

Program playback/Random playback (CD)

You can arrange the order of tracks on the disc.

VCD

Program Playback

23 5 8 11

16 9 12

4710

Repeat

Off

Play Mode

Program

/Enter/0 9/Cancel/Play Mode

Clear

Random playback

VCD

Press PLAY MODE in the stop mode.

Press / to select Play Mode, then press

/ to select “Random”.

Press PLAY

The Random Playback will start.

Repeat

Play Mode

Random

Off

/Enter/Play Mode

ENTER

▲ / ▼ /

PLAY MODE

PLAY

0–9

654

321

Clear Program Playback

5811

16 9 12

4710

Repeat

Off

Play Mode

Program

/Enter/0 9/Cancel/Play Mode

Note:

In playing back the Video CD with PBC, you can not set

Random playback.

Note:

In playing back the Video CD with PBC, you can not set

Program playback.

SET

–

ENTER

SET

–

ENTER

SP/SLP

PLAY MODE

SP/SLP

PLAY MODE

SET

–

ENTER

SET

–

ENTER

PLAY

CANCEL

Advanced playback (DVD)

2C53601A (E)p50-53 3/10/04, 11:3453

Press TOP MENU during playback.

Title menu appears on the screen.

Press / or / to select the desired title.

Changing angles/Title selection/DVD menu

Changing angles

Press ANGLE during playback.

The current angle will appear.

Advanced playback (DVD)

When playing back a disc recorded with multi-angle facility,

you can change the angle that you are viewing the scene from.

1/9

Press ANGLE repeatedly until the desired angle

is selected.

Note:

Depending on the DVD, you may not be able to change the

angles even if multi-angles are recorded on the DVD.

Title selection

Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.

Press ENTER or PLAY.

The playback of the selected title will

start.

Note:

Depending on the DVD, you may not be able to select the title.

Depending on the DVD, a “title menu” may simply be called a

“menu” or “title” in the instructions supplied with the disc.

DVD menu

Press MENU during playback.

The DVD menu appears on the screen.

• Press MENU again to resume

playback at the scene when you

pressed MENU.

Press / or / to select the desired item.

Some DVDs allow you to select the disc contents using the menu.

When you play back these DVDs, you can select the subtitle language and sound-track language, etc. using the menu.

Press ENTER.

The menu continues to another

screen. Repeat steps 2 and 3 to set

the item completely.

ANGLE

ENTER

▲ / ▼ /

TOP MENU

PLAY

COUNTER RESET

ANGLE

COUNTER RESET

ANGLE

TOP MENU

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

PLAY

Note:

Depending on the DVD, you may not be able to resume

playback from the scene point when you pressed MENU.

2C53601A (E)p54-57 3/10/04, 11:3454

Advanced playback (DVD)

During disc playback press AUDIO.

Press or to select “On”.

Changing soundtrack language

Press AUDIO during playback.

The current soundtrack language will

appear.

Press AUDIO repeatedly until the desired lan-

guage is selected.

The on-screen display will disappear

after a few seconds.

Changing soundtrack language/

Setting surround sound

You can select the language when you play a multilingual disc.

Notes:

• If the desired language is not heard after pressing the

button several times, the language is not recorded on

the disc.

• Changing soundtrack language is cancelled when you

open the disc tray. The initial default language or available

language will be heard if the disc is played back again.

AUDIO

In case of Video CD playback

Audio type changes as follows each time you press AUDIO.

Setting surround sound

This DVD/VCR equipped with a “SPATIALIZER VIRTUAL SURROUND”. It can produce the effect of being in a cinema

or a concert hall.

Spatializer

3-Dimensional Sound Processing provided by

Desper Products. Inc.

Certain audio features of this product manufactured under

a license from Desper Products, Inc., Spatializer

and the

circle-in-square device are trademarks owned by Desper

Products, Inc.

To cancel Surround mode:

Follow the left steps 1~2, then press

or to select the

“Off” position.

Note:

The “SPATIALIZER VIRTUAL SURROUND” is effective only

for the sound of disc.

DVD

VCD

DVD

VCD

Function setup (DVD)

AUDIO SELECT

AUDIO

AUDIO SELECT

AUDIO

AUDIO SELECT

AUDIO

SET

–

ENTER

Function setup (DVD)

2C53601A (E)p54-57 3/10/04, 11:3455

During DVD KARAOKE disc playback, press

AUDIO.

On : The primary vocal is output

when it is recorded on the disc.

Off : The primary vocal is not output.

Press

or to select “On” or “Off”.

Function setup (DVD)

Setting subtitles/Karaoke playback

Turning the subtitles on and off

Press SUBTITLE during playback until “Off”

appears.

When playing back a disc recorded with subtitles, you can turn the subtitles on or off.

SUBTITLE

Note:

Depending on the DVD, you may not be able to turn

the subtitles on even if they are recorded on it.

Depending on the DVD, you may not be able to turn

the subtitles off.

Off

Changing the subtitle language

Press SUBTITLE repeatedly during playback until

your desired language appears.

The on-screen display will disappear after a few

seconds.

You can select the language when playing back a disc recorded with multi-lingual subtitles.

Notes:

• Changing subtitle language is cancelled when you open

the disc tray.

• Depending on the DVD, you may not be able to change

the subtitles even if multilingual subtitles are recorded

on it. While playing the DVD, the subtitle may change

when: -you open or close the disc tray -you change the

title.

• In some cases, the subtitle language is not changed to

the selected one immediately.

1/32 Eng

Karaoke playback

You can turn the vocal on or off recorded on the DVD KARAOKE.

Notes:

• The vocal output feature is used during playback of

Dolby Digital (multi-channel) recorded DVD KARAOKE

discs. This feature allows you to turn off vocal audio

tracks, or restore them for background accompaniment.

• When playing Karaoke, connect appropriate audio

equipment such as an amplifier to the DVD/VCR.

▲ / ▼ / /

AUDIO

Press ▲ or ▼ until the KARAOKE symbol ( )

appears.

• If you play non-Karaoke disc, the KARAOKE

symbol (

) does not appear.

ATR

SUBTITLE

ATR

SUBTITLE

AUDIO SELECT

AUDIO

SET

–

ENTER

SET

–

ENTER

2C53601A (E)p54-57 3/10/04, 11:3456

Advanced playback (DVD)

Press SETUP in the stop mode or No Disc.

Press

or to select “Picture”.

Press or ENTER, then press or to select

“E.B.L.”.

Press / or ENTER to select “On” or “Off”.

On: Enhanced grey scale (0 IRE cut off)

Off: Standard grey scale (7.5 IRE cut off)

Setting E.B.L.

ENTER

▲ / ▼ /

E.B.L. (Enhanced Black Level)

To select the black level of playback pictures, set your preference

and monitor’s ability.

RETURN

SETUP

/Enter/Setup/Return

Language Picture Parental OtherSound

To make SETUP screen disappear, press SETUP

r RETURN while the SETUP screen is being dis-

played.

Tv Screen

Display

4:3

/Enter/Setup/Return

Language Picture Parental OtherSound

JPEG Interval

Select Files

All

Off

E.B.L.

Tv Screen

Display

4:3

/Enter/Setup/Return

Language Picture Parental OtherSound

JPEG Interval

Select Files

All

Off

E.B.L.

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

CH – CH

ENTER

VCR MENU

SETUP

RETURN

Function setup (DVD)

2C53601A (E)p54-57 3/10/04, 11:3457

Function setup (DVD)

Press SETUP in the stop mode or No Disc.

Press

or to select “Picture”.

Press or ENTER, then press or to select

“Tv Screen”.

Press or ENTER.

Press or to select your desired screen

type, then press ENTER.

Setting the aspect ratio of TV screen

ENTER

▲ / ▼ /

Setting the aspect ratio of TV screen

You can select the aspect ratio for your TV.

The following pages describe the setup/operation in DVD mode.

RETURN

SETUP

/Enter/Setup/Return

Language Picture Parental OtherSound

You have the following screen sizes to choose from:

4:3

Letter box:

Select this mode when connecting to a conventional TV.

When playing back a wide screen-DVD disc, it displays

the wide picture with black bands at the top and bottom of

screen.

4:3

Pan scan:

It displays the wide picture on the whole screen with left

and right edges automatically cut off.

16:9

Wide:

Select this mode when connecting to a wide-screen TV.

A wide screen picture is displayed full size.

To make SETUP screen disappear, press SETUP

or RETURN while the SETUP screen is being dis-

played.

Note:

If the DVD disc is not formatted in the pan & scan style, it dis-

plays 4:3 style.

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

RETURN

Tv Screen

Display

/Enter/Setup/Return

Language Picture Parental OtherSound

JPEG Interval

Select Files

All

Off

E.B.L.

4:3

4:34:3

16:9

Tv Screen

Display

4:3

/Enter/Setup/Return

Language Picture Parental OtherSound

JPEG Interval

Select Files

All

Off

E.B.L.

2C53601A (E)p58-61 3/10/04, 11:3558

Function setup (DVD)

00:34:56 01:12:33 00:34:56 01:12:33

1/9

Title 1/99

1/8

1/32

Chapter 1/999

Eng DolbyDigital

Eng

Each press of DISPLAY, the status display of the disc

will appear on the screen and change as follows.

DVD

To make status display disappear, press DISPLAY again.

Setting on screen display

Press SETUP in the stop mode or No Disc.

Press

or to select “Picture”.

Press or ENTER, then press or to select

“Display”.

On screen display can be switched on or off when you press the buttons.

/Enter/Setup/Return

Language Picture Parental OtherSound

Status display of disc

DVD

VCD

When you playback the CD disc, the status display will

appear on the screen and continue displaying.

ENTER

▲ / ▼ / /

RETURN

SETUP

DISPLAY

Audio CD

Video CD

34:56 71:33

Track 11/99

00:12 04:32

Tv Screen

Display

Off

/Enter/Setup/Return

Language Picture Parental OtherSound

JPEG Interval

Select Files

All

Off

4:3

Off

E.B.L.

Tv Screen

Display

/Enter/Setup/Return

Language Picture Parental OtherSound

JPEG Interval

Select Files

All

Off

4:3

Off

E.B.L.

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

RETURN

On: On screen displays appear when you press

the buttons (factory setting).

Off: On screen displays do not appear when you

press any buttons.

Press

/ or ENTER to select “On” or “Off”.

To make SETUP screen disappear, press SETUP or

RETURN while the SETUP screen is being displayed.

Setting on screen display/Status display of disc

2C53601A (E)p58-61 3/10/04, 11:3559

Dynamic Range Control

Press SETUP in the stop mode.

Press

or to select “Sound”.

Press or ENTER to select “Dialogue”.

Press or ENTER, then press or to select

desired setting.

To make SETUP screen disappear, press SETUP

or RETURN while the SETUP screen is being

displayed.

Dynamic Range Control

DRC (Dynamic Range Control) enables you to control the dynamic range so as to

achieve a suitable sound for your equipment.

ENTER

▲ / ▼ /

RETURN

SETUP

/Enter/Setup/Return

Language Picture Parental OtherSound

Dialogue

Off

/Enter/Setup/Return

Language Picture Parental OtherSound

Dialogue

On : DRC(TV)

Off : DRC(Std)

/Enter/Setup/Return

Language Picture Parental OtherSound

Off

Notes:

• This function works only during playback of Dolby Digital

recorded discs.

• The level of Dynamic Range Reduction may differ

depending on DVD video disc.

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

RETURN

On: Loud sound such as explosion or the

like is toned down slightly when played

back. This makes it suitable for when it is

connected to a stereo.

Off: It plays back at the recording level on the

disc.

Function setup (DVD)

2C53601A (E)p58-61 3/10/04, 11:3560

Function setup (DVD)

Parental control setting

Some discs are specified not suitable for children. Such discs can be limited

not to play back with the unit.

Parental control setting

Press ENTER to store the password.

Note: Now the rating is locked and the

setting cannot be changed unless you

enter the correct password.

Press SETUP or RETURN to remove the paren-

tal control screen.

Notes:

• If each setup (pages 57~66) has been completed, the

unit can always be worked under the same

conditions (especially with DVD discs).

Each setup will be retained in the memory if you turn

the power off.

• Depending on the discs, the unit cannot limit playback.

• Some discs may not be encoded with specific rating

level information though its disc jacket says “adult.” For

those discs, the age restriction will not work.

ENTER

▲ / ▼ /

RETURN

SETUP

0–9

CANCEL

VCR MENU

SETUP

RETURN

SET

–

ENTER

Press SETUP in the stop mode or No Disc.

Press

or to select “Parental”. Then press

or ENTER.

Press or to select “Parental”, then press

or until the level you require appears.

654

321

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

• Level Off:

The parental control setting does not function.

• Level 8: All DVD software can be played back.

• Level 1: DVD software for adults cannot be played

back.

• Select from the level 1 to level 8. The limitation will be

more severe as the level number is lower.

Press or to select “Password”.

Press Number buttons (0

9) to input a 4-digit password.

Be sure to remember this number!

• If you input a wrong number,

press CANCEL.

2C53601A (E)p58-61 3/10/04, 11:3561

To change the parental level

Press SETUP in the stop

mode or No Disc.

Press

or to select “Parental”.

Then press

or ENTER.

Press Number buttons (0–9) to enter the pass-

word you have stored.

Press ENTER.

The rating is now unlocked.

Press or to select “Parental”, then press

or to change the parental level.

To change the parental level

Function setup (DVD)

Press or to select “Password”, then press

Number buttons (0–9) to enter the password.

Note: You can change the password

if you want.

Press ENTER.

Now the parental level is changed and

locked.

Press SETUP or RETURN

to remove the parental control screen.

Password

Parental

/Enter/Setup/Return

0 9/Cancel

Language Picture Parental OtherSound

ENTER

▲ / ▼ /

RETURN

SETUP

0–9

VCR MENU

SETUP

SET

–

ENTER

654

321

SET

–

ENTER

SET

–

ENTER

654

321

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

RETURN

If you forget the password...

1. Press OPEN/CLOSE to open the disc tray.

2. Remove the disc.

3. Press OPEN/CLOSE again to close the disc tray.

“No Disc” appears on the screen.

4. While holding 7 down on the remote control, press

STOP on the front panel. “PASSWORD CLEAR” ap-

pears on the screen.

5. Enter a new password again.

OPEN/CLOSE

STOP

2C53601A (E)p62-67 3/10/04, 11:3562

Function setup (DVD)

Reading

Temporary disabling of rating level by DVD disc

Depending on the DVD disc, the disc may try to temporarily cancel the rating

level that you have set.

It is up to you to decide whether to cancel the rating level or not.

Temporary disabling of rating level by DVD disc

Load a DVD disc and press PLAY or OPEN/

CLOSE on the unit

If the DVD disc has been designed to temporarily

cancel the Rating level, the screen which follows

the “Reading” screen will change, depending on

which disc is played. If you select “YES” with the

ENTER key, “Your disc exceeds the parental

control level#.” screen will then appear.

If you wish to cancel the set rating level temporarily,

select “Parental Control Level” with

or , then

press ENTER. If the 4-digit password at step 2 on

page 62 has been set, the password entering

screen will appear as shown in step 4.

Alternatively, if the password has not been set,

playback will commence. If you don’t know (or have

forgotten) the password, select “Cancel Picture”.

The setting screen will disappear. Press OPEN/

CLOSE to remove the disc.

Note:

This temporary cancellation of rating level will be kept until the

disc is ejected.

When the disc is ejected, the original rating level will be set again

automatically.

Enter the password with Number buttons (0–9).

Then press ENTER.

If you interrupt the entering, press

RETURN.

Playback will commence if the entered

password was correct.

Your disc exceeds

the parental control level#.

Parental Control Level

Cancel Picture

/Enter/Return

Please enter the

4 digit password

Cancel

/ReturnEnter/0

ENTER

▲ / ▼

RETURN

PLAY

0–9

OPEN/CLOSE

654

321

PLAY

SET

–

ENTER

SET

–

ENTER

RETURN

2C53601A (E)p62-67 3/10/04, 11:3563

Function setup (DVD)

Setting OSD language

Press SETUP in the stop mode or NO DISC.

Press

or to select “Other”.

Press or ENTER to select “OSD Language”.

DVD

VCD

Language Other

/Enter/Setup/Return

Picture ParentalSound

Language

OSD Language English

Other

/Enter/Setup/Return

Picture ParentalSound

To make SETUP screen disappear, press SETUP

or RETURN while the SETUP screen is being

displayed.

If the unit does not operate properly: Static electricity,

etc., may affect the player's operation. Disconnect the

AC power cord once, then connect it again.

ENTER

▲ / ▼ /

RETURN

SETUP

Setting OSD language

The setup language can be selected.

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

RETURN

Press or ENTER and then press or to

select desired language (e.g. English), then

press ENTER.

Language

OSD Language English English

Francais

Espanol

Other

/Enter/Setup/Return

Picture ParentalSound

SET

–

ENTER

2C53601A (E)p62-67 3/10/04, 11:3564

Function setup (DVD)

Setting language

Press SETUP in the stop mode or No Disc.

Press

or to select “Language”.

Press or ENTER, then press or to select

desired langugage item.

Press or ENTER.

Press

or to select your desired language,

then press ENTER.

English, Francais, Espanol:

The selected language will be heard or seen.

Other:

Other language can be selected (see “Language code

list” on page 67).

Original: (Audio)

The unit will select the first priority language of each

disc.

Automatic: (Subtitle)

• The unit will automatically select the

same language in

the AUDIO setting.

• When the unit selects the same language as the

AUDIO,

the subtitles will not appear during playback.

• When you do not use the same language as

the AUDIO,

the subtitles will appear during playback.

Off: (Subtitle)

Subtitles do not appear.

Setting language

You can select the language of “Menu”, “Subtitle” and “Audio” if their languages

are recorded onto the disc more than one language.

To make SETUP screen disappear, press SETUP

or RETURN while the SETUP screen is being

displayed.

/Enter/Setup/Return

Language Picture Parental OtherSound

Subtitle

Audio

English

Automatic

English

/Enter/Setup/Return

Subtitle

Audio

English

Automatic

English

Francais

English

Espanol

Other

Language Picture Parental OtherSound

/Enter/Setup/Return

ENTER

▲ / ▼ /

RETURN

SETUP

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

RETURN

Note:

If the selected language is not recorded on the disc, the first-

priority language is selected.

2C53601A (E)p62-67 3/10/04, 11:3565

Function setup (DVD)

Selecting PROGRESSIVE scan

The progressive scan capability provides the highest resolution pictures with less

flicker and line structure.

If you are using the Component video jacks, but are connecting the DVD/VCR to

a standard (analog) television, set PROGRESSIVE to Off.

If you are using the Component video jacks for connection to a TV or monitor that

is compatible with a progressive scan signal, set PROGRESSIVE to On.

Preparation:

• Connect to a TV equipped with component jacks.

• Turn ON the TV and set it to the corresponding video input

mode.

• Set the S-VIDEO/COMPONENT video selector switch on

the rear panel to COMPONENT position.

• Press VCR DVD selector to select the DVD mode. (The

DVD indicator will light.)

INPUT SELECT

PROGESSIVE

Press PROGRESSIVE in the stop mode.

The progressive indicator “

” on the

display window will light.

• The unit recognizes the picture

source (film or video) of the current

disc according to the disc information.

Press PLAY to start playback.

PLAY

Notes:

• Some discs may not be played back with the progressive

scanning mode correctly because of the disc characteristics

or recording condition.

• If your TV does not accept the progressive scan format, the

picture will appear scrambled if you select progressive scan

output from the unit. In such a case, select PROGRESSIVE

scan Off.

• Once PROGRESSIVE scan On, all other video outputs are

disabled except component video outputs.

• You cannot make the progressive scanning mode active in

following cases.

– The unit is in the VCR mode.

– The disc is played back in the DVD mode.

– The S-VIDEO/COMPONENT video selector switch is set to

S-VIDEO position.

There are two types of source content in pictures recorded in

DVD video discs: film content (pictures recorded from films

at 24 frames per second) and video content (video signals

recorded at 30 frames per second).

When the unit plays back a film source material, uninterlaced

progressive output signals are created using the original

information. When a video content is played back, the unit

interleaves lines between the interlaced lines on each to

create the interpolated picture and outputs as the progressive

signal.

DVD

VCD

To select PROGRESSIVE scan Off

Press PROGRESSIVE in the stop mode.

The progressive indicator “

” on the display window will

go off.

VCR DVD

2C53601A (E)p62-67 3/10/04, 11:3566

Function setup (DVD)

Language code list

Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio”

Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919

Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921

Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922

Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925

Amharic 1123 Galician 1722 Malay 2329 Spanish 1529

Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931

Armenian 1835 German 1415 Maltese 2330 Swahili 2933

Assamese 1129 Greek 1522 Maori 2319 Swedish 2932

Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022

Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017

Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011

Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030

Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015

Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018

Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225

Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019

Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025

Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028

Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021

Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033

Catalan 1311 Japanese 2011 Quechua 2731 Ukrainian 3121

Chinese 3618 Javanese 2033 Rhaeto-Romance2823 Urdu 3128

Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136

Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219

Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225

Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335

Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325

English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418

Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019

Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525

Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631

Language Name Code Language Name Code Language Name Code Language Name Code

Others

2C53601A (E)p62-67 3/10/04, 11:3567

Others

Troubleshooting

Check the following guide for the possible cause of a problem before contacting service.

SYMPTOMS POSSIBLE SOLUTIONS

• Make sure the power cord is plugged in.

• Try another AC outlet.

• Power is off, check fuse or circuit breaker.

• Unplug unit, then plug it back in.

• Select the DVD or VCR mode before operating.

DVD/VCR does not operate.

DVD/VCR

PAGE

–

30,42

The remote control does not function.

• Aim the remote control at the remote sensor.

• Operate within Approx. 7 Meters or reduce the light in the room.

• Clear the path of the beam.

• The batteries are weak. Replace the batteries.

• Check the batteries are inserted correctly.

DVD

No picture.

• Antenna connection is not correct or antenna cable is disconnected.

• The video channel is not in the correct position or the TV is not set to the video

channel 3 or 4.

• Check the unit is connected correctly.

• The video input selector of the TV is not set to VIDEO. Set to VIDEO (or

equivalent).

• Channel is set to the external mode.

No sound.

• Check the unit is connected correctly.

• Check the input selector of the amplifier is set properly.

• The unit is in the Special playback mode.

14~17

14~19

–

14~19

–

31,44

• Select proper language in the menu options.Display is not shown in your language. 64

Playback doesn’t start.

• No disc is inserted.

• The disc may be dirty. Clean up the disc.

• The unit cannot play DVD-ROMs, etc.

Stopping playback, slow-motion play, repeat

play, or memory play, etc. cannot be

performed.

• Some discs may not do some of the functions.

–

No CATV reception.

• Check all CATV connections.

• Station or CATV system problems, try another station.

16,17

Noise bars on screen.

• Tracking adjustment beyond range of automatic tracking circuit. Try Manual

tracking adjustment.

• Video heads are dirty.

• The tape is worn or damaged.

VCR

• The erase prevention tab of the video cassette is broken off.

• The unit is in the external input mode.

TV recording does not work. 29,34

Timer recording does not work.

• The time is not set correctly.

• The recording start/end time is not set correctly.

• The TIMER REC has not been pressed (

is not lit).

–

No picture, or the screen is blurred or divided

into two parts.

• The S-VIDEO/COMPONENT selector is not set correctly.

• The PROGRESSIVE scan is On through the unit is connected to a TV

via the VIDEO OUT or the S-VIDEO OUT jack.

No subtitle.

• Some discs have no subtitles.

• Subtitles are cleared. Press SUBTITLE.

Angle cannot be changed.

• Multi-angles are not recorded on the DVD disc.

• The function is prohibited with the unit or the disc.

appears on the screen.

No 4:3 (16:9) picture. • The setup does not match your TV.

No on-screen display. • Select Display “On”.

No surround sound. • The setup does not match your stereo system.

The unit or remote operation key is not

functioning.

• Turn off the unit and unplug the AC power cord for several minutes, then replug it.

Playback does not start when the title is

selected.

• Check the Parental setup.

Audio soundtrack and/or subtitle language

is not changed when you play back a DVD.

• Multilingual language is not recorded on the DVD disc.

–

61,62

2C53601A (E)p68-BACK 3/10/04, 11:3568

Others

Specifications

AC 120 V 60 Hz

Operation: 18 W, Stand by: 2 W

7.9 lbs (3.6 kg)

Width: 16-15/16 inches (430 mm)

Height: 3-7/8 inches (99 mm)

Depth: 9-13/16 inches (250.5 mm)

181 channel freq. synthesized

VHF 2-13

UHF 14-69

CATV 125 Channels

UHF/VHF In/Out: 75 Ω coaxial

Channel 3 or 4, Switchable

NTSC

4 Rotary heads

Hi-Fi sound - 2 Tracks / MONO sound - 1 Track

20 Hz to 20,000 Hz

More than 90dB

Approx. 1 minute and 48 seconds (with T-120 Cassette Tape)

DVD (12 cm, 8 cm), CD (12 cm, 8 cm)

DVD: 4 Hz-22 kHz, CD: 4 Hz-20 kHz

90dB (DVD)

0.02% (DVD)

Less than 0.01% Wrms

Temperature: 5˚C-40˚C (41˚F-104˚F), Operating status: Horizontal

Power supply

Power consumption

Weight

Dimensions

Tuner

Antenna input/output

RF channel output

Color system

Video head

Audio track

Hi-Fi frequency response

Hi-Fi dynamic range

F.FWD/REW time at 25˚C (77˚F)

Applicable disc

Frequency range

S/N ratio

Harmonic distortion

Wow and flutter

Operating conditions

General

Input/Output

DVD/VCR

Video input 1.0 V (p-p), 75 Ω, negative sync., pin jack x 2

Video output 1.0 V (p-p), 75 Ω, negative sync., pin jack x 1

Audio input –8 dBm, 50 kΩ, negative sync., pin jack (L/R) x 2

Audio output –8 dBm, 1 kΩ, negative sync., pin jack (L/R) x 1

DVD

S-video output (Y) 1.0 V (p-p), 75 Ω, negative sync., Mini DIN 4-pin × 1

Component video output (Y) 1.0 V (p-p), 75 Ω, negative sync., pin jack × 1

B)/(PR) 0.7 V (p-p), 75 Ω, pin jack × 2

Audio output (BITSTREAM/PCM 0.5 V (p-p), 75 Ω, pin jack × 1

COAXIAL)

Audio output (BITSTREAM/PCM Optical connector × 1

OPTICAL)

Audio output (ANALOG) –12 dB, 1 kΩ, pin jacks (L, R) × 1

S-VIDEO/COMPONENT video selector Slide switch × 1

Supplied accessories

Audio/video cable ................................................. 1

Remote control (SE-R0108) ................................. 1

Batteries (R03/AAA) ............................................. 2

75 ohm coaxial cable ............................................ 1

• Designs and specifications are subject to change without notice.

2C53601A (E)p68-BACK 3/10/04, 11:3569

Others

Limited warranty

2C53601A (E)p68-BACK 3/10/04, 11:3670

Others

2C53601A (E)p68-BACK 3/10/04, 11:3671

Printed in Thailand04/04 U

2C53601A (E)p68-BACK 3/10/04, 11:3672

REPRODUCTOR DE DVD & VIDEOGRABADOR DE CASSETTE

SD-V396SU

ALL

Referencìa rápida

Este dispositivo no graba en cinta DVDs protegidos contra copias.

RIESGO DE DESCARGA

ELECTRICA NO ABRIR

PRECAUCION

AVISO:

PARA REDUCIR EL RIESGO DE DESCARGA

ELECTRICA, NO RETIRE LA CUBIERTA (O POSTE-

RIOR). EN EL INTERIOR DEL APARATO NO HAY

COMPONENTE ALGUNO QUE PRECISE SERVICIO DE

MANTENIMIENTO A CARGO DEL USUARIO. SOLICITE

CUALQUIER OPERACION DE MANTENIMIENTO A

PERSONAL DE SERVICIO CALIFICADO.

El símbolo del rayo dentro de un triángulo equilátero

tiene por finalidad alertar al usuario acerca de la

presencia de tensión peligrosa (sin aislación) en el in-

terior del producto, que puede tener la intensidad suficiente

como para constituir un riesgo de descarga eléctrica.

El signo de exclamación dentro de un triángulo

equilátero tiene por finalidad alertar al usuario de

importantes instrucciones de operación y

mantenimiento (servicio) en la literatura que acompaña

a este aparato.

AVISO: Para reducir el riesgo de incendio o descarga eléctrica, no exponga esta unidad a la lluvia ni a la

humedad.

ADVERTENCIA: Este equipo ha sido sometido a pruebas y cumple con los límites establecidos para un aparato digital

de Clase B, de acuerdo con la Parte 15 del Reglamento de la FCC. Estos límites están diseñados para

proporcionar protección razonable contra interferencias perjudiciales en una instalación residencial.

Este equipo genera o emplea energía de radiofrecuencia y, si no es instalado y empleado de acuerdo

con estas instrucciones, puede causar interferencias perjudiciales a las radiocomunicaciones.

Sin embargo, no garantizamos que no ocurrirán interferencias en una instalación en particular. Si este

equipo causa interferencias perjudiciales a la recepción radial o televisiva, situación que puede ser

determinada apagando y encendiendo el equipo, se sugiere al usuario que trate de corregir tal

interferencia mediante una o más de las siguientes medidas:

- Reorientar o relocalizar la antena receptora.

- Incrementar la separación entre el equipo y el receptor.

- Conectar el equipo a un tomacorriente o circuito diferente al que está conectado al receptor.

- Consultar con el concesionario o un técnico experimentado solicitándole su asistencia.

PRECAUCION: El usuario corre el riesgo de perder la autorización para hacer funcionar este equipo en caso de que

ejecute un cambio o modificación no aprobado por la parte responsable para la conformidad con las

Reglas FCC.

PRECAUCION:

ESTE TOCADISCOS DE VIDEO DIGITAL UTILIZA UN SISTEMA LASER.

PARA UTILIZAR CORRECTAMENTE ESTE PRODUCTO, LEA CUIDADOSAMENTE ESTE MANUAL DE INSTRUCCIONES Y

GUARDELO PARA SU REFERENCIA EN EL FUTURO. SI FUERA NECESARIO HACER UN MANTENIMIENTO DE ESTE

APARATO, CONSULTE CON UN CENTRO DE SERVICIO AUTORIZADO-LEA EL PROCEDIMIENTO DE SERVICIO.

EL USO DE LOS CONTROLES, AJUSTES O LA REALIZACION DE OTROS PROCEDIMIENTOS QUE NO SEAN LOS

ESPECIFICADOS AQUI PUEDE PROVOCAR UNA EXPOSICION A RADIACIONES PELIGROSAS.

PARA EVITAR LA EXPOSICION DIRECTA A LOS RAYOS LASER, NO TRATE DE ABRIR LA CAJA. PUEDE HABER UNA

RADIACION LASER VISIBLE AL ABRIR LA CAJA.

NO MIRE HACIA EL RAYO.

DIGITAL VIDEO

2C53607A (SP) Q Sheet 11/3/04, 6:311

1. LEA LAS INSTRUCCIONES

Antes de usar la unidad, lea detenidamente todas las instrucciones de seguridad

y operación.

2. CONSERVE ESTE MANUAL DE INSTRUCCIONES

Conserve las instrucciones de seguridad y operación para consultas futuras.

3. RESPETE LAS ADVERTENCIAS

Observe estrictamente todas las advertencias impresas en la unidad y las

incluidas en el manual de instrucciones.

4. SIGA LAS INSTRUCCIONES

Siga todas las instrucciones de operación y uso.

5. LIMPIEZA

Antes de limpiar este videograbador, desconéctelo del tomacorriente mural. No

use limpiadores líquidos ni aerosol. Utilice sólo un paño húmedo para limpiar el

exterior del mueble.

6. ENCHUFES

El fabricante de esta unidad no hace ninguna recomendación de accesorios ya

que pueden ser peligrosos.

7. AGUA Y HUMEDAD

No utilice este aparato cerca del agua. Por ejemplo cerca de una bañera, la-

vabo, pileta de la cocina, lavadero, en un sótano húmedo o cerca de una piscina.

8. ACCESORIOS

No instale esta unidad en un carro, soporte, trípode o mesa inestables. La unidad

podría caerse, causando serias lesiones, resultando también severamente

dañada a la unidad.

8A. La combinación de aparato y carro deberá ser movida con cuidado. Las

detenciones bruscas, la fuerza excesiva y las superficies disparejas podrán hacer

que el aparato y el carro se vuelven.

9. VENTILACION

Las ranuras y aberturas en la parte trasera o inferior del mueble son para

ventilación permiten un funcionamiento fiable de la unidad, protegiendo contra

calentamiento excesivo. Estas aberturas no deberán ser bloqueadas ni cubiertas.

Para evitar bloquear las aberturas, nunca sitúe la unidad encima de una cama,

sofá, alfombra u otra superficie similar. Tampoco instale la unidad cerca o encima

de un radiador o calefactor. La unidad no deberá ser instalado en un mueble

empotrado, como ser una repisa para libros o bastidor, a menos que se pueda

garantizar una ventilación adecuada, y/o cuando las instrucciones del fabricante

así lo especifiquen.

10. FUENTES DE ALIMENTACION

Esta unidad sólo deberá ser operada mediante el tipo de fuente de alimentación

especificado en la etiqueta indicadora. Si no está seguro del tipo de fuente de

alimentación que tiene en su casa, consulte a su distribuidor o a la compañía de

electricidad local. En el caso de unidades diseñadas para funcionar a pilas o con

otras fuentes de alimentación, consulte el manual de instrucciones respectivo.

11. CONEXIÓN A TIERRA O POLARIZACION

Esta unidad está equipada con una clavija polarizada de corriente alterna (una

clavija que tiene una espiga más ancha que la otra). Esta clavija solamente

puede ser insertada en el tomacorriente en una sola dirección. Esta es una

medida de seguridad. Si no pudiera insertar completamente la clavija en el

tomacorriente, vuelva a intentarlo invirtiendo la clavija. Si aún no fuera posible

insertar la clavija, tome contacto con un electricista para que reemplace su

tomacorriente obsoleto. En lugar de la clavija polarizada de corriente alterna, su

unidad puede estar equipada con una clavija de conexión a tierra de 3 alambres

(una clavija con una tercera espiga de conexión a tierra). Este tipo de clavija

sólo puede ser insertado en un tomacorriente con contacto a tierra. Esto también

es una medida de seguridad. Si no pudiera insertar la clavija en el tomacorriente,

tome contacto con un electricista para que reemplace su tomacorriente obsoleto.

No modifique las características de seguridad de la clavija de conexión a tierra.

12. PROTECCION DEL CABLE DE ALIMENTACION

Los cables de alimentación deberán ser tendidos de manera tal que la probabilidad

de que sean pisados o aplastados por otros objetos sea mínima. Preste especial

atención a las clavijas de los cables, a los receptáculos, y al punto por donde

salen del aparato.

13. TORMENTAS ELECTRICAS

Como medida de protección durante tormentas eléctricas, o cuando el

videograbador permanezca sin uso durante períodos prolongados de tiempo,

desconéctelo del tomacorriente mural y desconecte la antena o el sistema de

cable. Esto evitará que la unidad resulte dañada por tormentas eléctricas o

sobretensiones en la línea de alimentación.

14. LINEAS DE ALIMENTACION

Un sistema de antena exterior no debería situarse cerca de líneas de alimentación

aéreas ni de otros circuitos de luz eléctrica o potencia, o donde pueda caerse o

entrar en contacto con tales líneas o circuitos de alimentación. Al instalar un

sistema de antena exterior, tenga mucho cuidado de no tocar tales líneas o

circuitos de alimentación, ya que el contacto con ellos podría ser fatal.

15. SOBRECARGA

No sobrecargue los tomacorrientes murales ni los cables de extensión, ya que

esto podría causar incendios o descargas eléctricas.

16. ENTRADA DE OBJETOS Y LIQUIDOS

Nunca introduzca objetos de ningún tipo por las aberturas de la unidad, ya que

podría tocar peligrosos puntos de alta tensión o piezas de cortocircuito,

provocando incendios o descargas eléctricas. Nunca derrame ni rocíe ningún

tipo de líquido sobre la unidad.

17. CONEXION A TIERRA DE LA ANTENA EXTERIOR

Si se conecta una antena externa o sistema de cable a la unidad, cerciórese de

que el sistema de antena o cable está conectado a tierra para darle protección

contra sobretensión y acumulación de carga estática. La Sección 810 del Código

Nacional de Electricidad, ANSI/NFPA 70, entrega información acerca de la manera

correcta de conectar a tierra el mástil y la estructura soportante, puesta a tierra

del alambre de entrada a una unidad de descarga de antena, tamaño de los

conductores de puesta a tierra, ubicación de la nidad de descarga de la antena,

conexión a los electrodos de tierra, y requisitos para el electrodo de tierra.

18. SERVICIO

No intente reparar la unidad usted mismo; al abrir o retirar las cubiertas usted se

expondrá a alta tensión y a otros peligros. Solicite todo servicio a personal

calificado.

Ejemplo:

a. Cuando el cable de alimentación o la clavija estén dañados.

b. Si se ha derramado líquido sobre la unidad, o si algún objeto ha caído dentro

del videograbador.

c. Si la unidad ha sido expuesta a la lluvia o al agua.

d. Cuando a pesar de haber seguido las instrucciones de operación, la unidad

no funcione normalmente.

Ajuste solamente los controles indicados en el manual de instrucciones;el

ajuste incorrecto de otros controles podrá causar daños a la unidad, la que

por lo general requerirá de un prolongado trabajo de reparación (por un

técnico calificado) para que sus condiciones normales de operación puedan

ser restablecidas.

e. Si la unidad se ha caída o si el gabinete se ha dañado.

f . Cuando la unidad muestre un cambio notorio en su rendimiento.

19. PIEZAS DE REPUESTO

Cuando sea necesario reemplazar piezas, asegúrese de que el técnico de servicio

emplee las piezas de repuesto especificadas por el fabricante, o piezas que

tengan las mismas características que las piezas originales. Los cambios no

autorizados podrán causar incendios, descargas eléctricas y otros problemas.

20. REVISION DE SEGURIDAD

Al finalizar cualquier servicio de mantenimiento o reparación de esta unidad,

solicítele al técnico que efectúe comprobaciones de seguridad para determinar

si el videograbador se encuentra o no en condiciones óptimas de operación.

21. CALOR

El producto debe ser situado lejos de fuente de calor como radiadores,

reguladores de calefacción, estufas o otros productos (incluyendo amplificadores)

que se producen calor.

22. BANDEJA DEL DISCO

No acerque sus dedos a la bandeja del disco cuando se está cerrando. Puede

recibir heridas graves.

23. CONEXION

Cuando conecte el producto a otro equipo, desconecte la alimentación y

desenchufe todos los equipos del tomacorriente. Si no lo hace, puede provocar

una descarga eléctrica y heridas graves.

Lea cuidadosamente el manual de instrucciones del otro equipo y respete las

instrucciones al hacer las conexiones.

24. RAYO LASER

No mire por la ranura de la bandeja del disco por las salidas de circulación de

aire del producto para ver la fuente del rayo láser. Puede dañar sus ojos.

25. DISCO

No utilice un disco rayado, deformado o reparado. Estos discos se pueden romper

fácilmente y provocar serias heridas o averías en el producto.

26. NOTA PARA LA PERSONA QUE INSTALE EL SISTEMA CATV

Se ha incluido este recordatorio para llamar la atención de quien instale el sistema

CATV, con respecto al Artículo 820-40 de la NEC, que entrega directivas de guía

para realizar una conexión adecuada a tierra y, en particular, especifica que el

cable de puesta a tierra debe ser conectado al sistema de conexión a tierra del

edificio, lo más cerca del punto de entrada del cable como sea posible.

INSTRUCCIONES IMPORTANTES

CONDENSACION

Se condensará humedad en la sección de funcionamiento del DVD/VCR si se

lo trae de un lugar fresco a una habitación caliente o si la temperatura en la

habitación sube repentinamente. En este caso, se verán afectadas las

prestaciones del DVD/VCR. Para evitarlo, deje el DVD/VCR a la nueva

temperatura durante aproximadamente una hora antes de conectarlo, o haga

que la temperatura en la habitación suba gradualmente.

También puede condensarse humedad durante el verano si el DVD/VCR está

expuesta a una corriente de aire del acondicionador de aire. En estos casos,

cambie el lugar donde está instalado el DVD/VCR.

2C53607A (SP) Q Sheet 11/3/04, 6:312

Conexión a un televisor

A SALIDA DE

VIDEO

(roja) (blanca)

(amarilla)

Flujo de la señal

a un tomacorriente de la red

(120 V CA, 60 Hz)

A ENTRADA DE VIDEO

(amarilla)

(roja)

(blanca)

AENTRADA DE AUDIO

A ENTRADA

DE ANTANA

Televisor o monitor

con entrada de

audio/video

A ENTRADA DE ANTANA

A SALIDA DE ANTANA

Antennas separadas

VHF y UHF

Cordón AUDIO/

VIDEO (incluido)

Seleccion de idioma en pantalla

Presione SET + o – para seleccionar el modo

LANGUAGE, luego presione ENTER.

Presione VCR MENU. Presione SET + o – para seleccionar

la opción “SYSTEM SETUP”, luego presione ENTER.

Presione SET + o – para seleccionar el idioma deseada:

inglés (ENGLISH), español (ESPAÑOL) o francés

(FRANCAIS), luego presione ENTER.

Presione VCR MENU para volver a la imagen normal de TV.

Ajuste del canal de video

Presione POWER para encender el DVD/VCR.

Presione VCR DVD para seleccionar el modo VCR.

Encienda el televisor y ajústelo al canal 3 o 4, en

correspondencia con el canal seleccionado en el paso 1.

Presione TV/VCR para seleccionar la posición VCR.

Presione el botón selector de canal en + o – (CH + / –) para

recibir una estación de TV de su área. El número de canal

aparecerá en la pantalla durante unos 4 segundos.

El indicador VCR del panel frontal se

iluminará.

El indicador VCR se iluminará.

Si utiliza la unidad por primera vez y

presiona VCR MENU, es posible que

aparezca la pantalla de menú SYSTEM

SETUP en lugar de la pantalla del menú

principal.

Mantenga presionado 3 o 4 durante 3 segundos en

el mode desconectado para seleccionar CH 3 o 4.

El número del canal

seleccionado parpadeará

en la pantalla durante 3

segundos.

3 4

VCR

DVD

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

TV/VCR

2C53607A (SP) Q Sheet 11/3/04, 6:313

Ajuste de reloj automatico

Ajuste de reroj manual

Connecte la antena o sistema de cable.

• Si utiliza una caja de cable,

enciéndala.

Enchufe el cable eléctrico de CA a un tomacorriente CA.

Compruebe que el DVD/VCR está apagado.

•

Si presiona POWER, el ajuste

automático no se activará.

Espere por lo menos tres minutos y presione POWER.

Presione CALL para verificar el reloj en la pantalla.

Si el reloj no ha quedado ajustado, verifique el estado

de la antena. El reloj automático no funciona en el

estado de recepción.

Presione SET + o – para seleccionar la optión

“SYSTEM SETUP”, luego presione ENTER.

Presione el botón SET + o – para establecer el mes,

y a continuación presione el botón ENTER.

Presione SET + o – para seleccionar la opción

“CLOCK SET”, luego presione ENTER.

Presione VCR MENU.

Ajuste el día, año y hora de acuerdo con el

procedimiento del paso 4.

Una vez ajustado el reloj, la fecha y la hora empiezan

a funcionar automáticamente.

Seleccion de TV/CATV

Presione VCR MENU.

Presione ENTER para seleccionar el modo TV o CATV.

La flecha indica el modo seleccionado.

Presione SET + o – para seleccionar el modo “TV/CATV”.

Presione VCR MENU para volver a la imagen normal de TV.

Ajuste automático de los canales

Luego presione ENTER.

Repita el paso 1 descrito arriba y presione SET + o –

para seleccionar la opción “AUTO CH MEMORY”.

Borrado de un canal de la memoria

Repita el paso 1 descrito arriba

y presione SET + o – para

seleccionar la opción “ADD/DELETE”, luego presione ENTER.

Presione los botones de número o SET + o –

para seleccionar un número de canal que desee

añadir o borrar.

Para añadir o borrar los canales deseados

Para añadir canales

Presione ENTER hasta que aparezca “ADD” en

la pantalla para añadir el canal sin memorizar.

Para borrar canales

Presione ENTER hasta que aparezca “DELETE”

en la pantalla para borrar el canal de la memoria.

El número del canal parpadeará.

Repita de a para añadir o borrar otro canal.

Presione SET + o – para

seleccionar la opción “CH

SETUP”, luego presione

ENTER.

Empieza la sintonización

automática. La indicación de

canal irá subiendo y cuando

termina, la pantalla vuelve a

su estado normal.

654

321

TV - Canales de VHF/UHF

CATV - Canales de TV CABLE

CALL

DISPLAY

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

VCR MENU

SETUP

SET

–

ENTER

2C53607A (SP) Q Sheet 11/3/04, 6:314

Función de búsqueda de imagen hacia atrás

Presione REW una o dos veces durante la reproducción.

Función de búsqueda de imagen hacia delante

Presione FWD una o dos veces durante la reproducción.

Para volver a la reproducción: Presione PLAY.

Presione PAUSE/STILL durante la reproducción. Para

continuar la reproducción normal: Presione PLAY o PAUSE/

STILL.

Imagen fija

Camara lenta

Presione el botón de parada STOP para detener la

grabacion.

Durante la reproducción presione SLOW.

Para volver a la reproducción: Presione PLAY o SLOW.

Avance cuadro a cuadro

Presione PAUSE/STILL durante la reproducción.

Presione SLOW repetidamente: La imagen avanza cuadro a

cuadro.

Para volver a la reproducción: Presione PLAY o PAUSE/STILL.

Grabacion de un programa de TV

Coloque un cassette en el cual la lengüeta de

protección contra borrados accidentales esté intacta.

El DVD/VCR se encenderá automáticamente.

Ajuste la opción TV/CATV en la posición apropiada.

Presione SP/SLP para seleccionar la velocidad de

cinta deseada SP o SLP.

TV - Canales de VHF/UHF

CATV - Canales de TV CABLE

Selección directa de canal en modo de TV:

Todos los canales podrán ser seleccionados en

forma instantánea usando sólo dos botones.

(Por ejemplo, para seleccionar el canal 2,

presione “0” y “2”. Si usted sólo presiona “2”, la

selección del canal se retardará dos segundos.)

Para los canales de 10 en adelante, presione

los dos digitos en orden.

Selección directa de canal en modo de CATV:

1-9 Presione 0 dos veces y luego 1 al 9

como se requiera. Ej.:para

seleccionar 2, presione “002”.

10-12 Presione primero el 0 y luego los 2

dígitos restantes en el orden de

izquierda a derecha. Ej.: presione

012 para “12”.

13-99 Presione 2 dígitos en orden.

Ej.: presione 22 para “22”.

100-125

Presione 3 dígitos en orden.

Ej.: Presione 110 para “110”.

Presione los botones de selección directa de canal para

seleccionar el canal o CH +/– a grabar:

Presione el botón REC.

Coloque una cinta pregrabada. (Cuando se carga una cinta de

cassette sin la lengüeta de prevención de borrado, la reproducción

comenzará automáticamente.)

Presione PLAY. La reproducción

comenzará. “ ” aparecerá en pantalla

durante 4 segundos aproximadamente.

PARA INICIAR LA REPRODUCCION

Presione STOP (PARADA) una vez. La

cinta parará, pero permanecerá cargada

y lista para reproducir. “ ” aparecerá en

pantalla durante 4 segundos

aproximadamente.

PARA INTERRUMPIR REPRODUCCION

Detenga la reproducción o la grabación mediante STOP.

Para rebobinar la cinta:

Presione REW.

Para avanzar la cinta:

Presione FWD.

Para detener el bobinado de la cinta, presione STOP. Para pasar

directamente a reproducción (sin presionar STOP), presione

PLAY.

Modo de búsqueda de imagen hacia delante/atrás

Mientras se bobina la cinta, puede pasar al modo de búsqueda

de imagen. Para ello, presione REW o FWD y manténgalo

presionado. La unidad volverá a bobinar la cinta en cuanto se

suelte el botón.

Reproducción

Rebobinado o avance rápido de la cinta

Búsqueda de imagen

El contador y “SP” o “SLP” se aparecerá

en la pantalla durante 4 segundos

aproximadamente.

654

321

“ ” aparecerá en la pantalla durante 4

segundos aproximadamente. El indicador

“ REC ” aparecerá en pantalla.

“ ” aparecerá en pantalla durante 4

segundos aproximadamente.

PLAY

REW

FWD

REW

FWD

SLOW

SP/SLP

PLAY MODE

SET

–

ENTER

REC/OTR

2C53607A (SP) Q Sheet 11/3/04, 6:315

Grabacion por temporizador

Presione VCR MENU.

Seleccione la opción TIMER REC SET y presione ENTER.

Presione SET + o – para seleccionar el N° de

programa, luego presione ENTER.

Presione SET + o – para seleccionar la fecha deseada,

luego presione ENTER.

Ajuste el tiempo de partida, tiempo de término, canal y

velocidad de cinta como en paso 3.

Para fijar otros programas, repita los pasos 2 al 4 para

fija el otro programas.

Presione TIMER REC. El símbolo de reloj ( )

aparecerá en el visualizador y el VCR quedará en

modo de espera para grabación.

• Para volver a la pantalla normal, presione

dos veces VCR MENU.

Al mismo tiempo, el modo VCR cambiará

automáticamente a modo DVD. Es posible

utilizar el DVD incluso cuando el VCR está

en modo de grabación por temporizador. Si

no utiliza el DVD, apáguelo.

Si desea ver la reproducción del DVD durante el OTR o grabación

estándar, presione VCR DVD para cambiar al modo DVD y

reproducir el DVD.

Grebacion por temporizador de un solo toque (OTR)

Coloque un cassette con la lengüeta de protección

contra borrados accidentales esté intacta.

El DVD/VCR se encenderá automáticamente.

Presione SP/SLP para seleccionar la velocidad de la

cinta deseada SP o SLP.

El contador y “SP” o “SLP” aparecerán en

pantalla durante 4 segundos

aproximadamente.

Ajuste la opción TV/CATV en la posición apropiada.

Presione el botones de selección de canales directos o

botón CH +/– para seleccionar el canal a ser grabado.

Presione OTR para comenzar la grabación. Presione el

botón nuevamente para detener la grabación después

de 30 minutos. Cada presión de OTR aumentará el

tiempo de grabación hasta un máximo de 6 horas. OTR

y el tiempo de grabación aparecerá en pantalla durante

4 segundos. Y

“ ” aparecerá en el visualizador.

654

321

TV - Canales de VHF/UHF

CATV - Canales de TV CABLE

Para cancelar OTR

Presione STOP (PARADA) para apagar la energía.

“ ” aparecerá en pantalla durante 4 segundos aproximadamente.

Presione

Una vez

2 veces

3 veces

4 veces

5 veces

GRABAC. NORMAL

0:30

1:00

1:30

2:00

3:00

4:00

5:00

6:00

GRABAC. NORMAL

Tiempo de Grabac.

Presione

6 veces

7 veces

8 veces

9 veces

10 veces

Tiempo de Grabac.

SET

–

ENTER

VCR MENU

SETUP

SET

–

ENTER

SET

–

ENTER

VCR MENU

SETUP

TIMER REC

SP/SLP

PLAY MODE

SET

–

ENTER

REC/OTR

2C53607A (SP) Q Sheet 11/3/04, 6:316

Presione STOP para terminar la reproducción.

• El aparato graba el punto de parada, según el disco.

Aparece “

” en la pantalla. Presione PLAY para

continuar reproduciendo (desde el mismo punto).

• Si presiona nuevamente STOP o se retira el disco

(Aparece “

” en la pantalla), el aparato borrará el punto

de parada.

Para la reproducción, presione STOP.

A continuación presione OPEN/CLOSE en el aparato.

Se abre la bandeja del disco.

Saque el disco y presione OPEN/CLOSE en el aparato y

presione POWER (

). La bandeja del disco se cierra

automáticamente y se desconecta el aparato.

Reproducción de cámara lenta

Presione PAUSE/STILL durante la reproducción normal para

hacer una pausa en la reproducción.

• Para seguir con la reproducción normal, presione PLAY.

ENCIENDA el TV y ajústelo en el modo de entrada de video.

Presione VCR DVD para seleccionar el modo DVD. (El

indicador DVD se iluminará.)

Preparación:

•

Presione OPEN/CLOSE en el aparato.

Se abrirá la bandeja del disco.

Coloque un disco en la bandeja. Sujete el disco, colóquelo

con el lado de etiqueta impresa hacia arriba, alinee en las

guía y coloque el disco en su posición correcta.

Presione PLAY o OPEN/CLOSE en el aparato.

La bandeja del disco se cierra automáticamente.

En la pantalla del TV la indicación “

” cambia a “Reading”

y empieza la reproducción.

• Aparece la pantalla del menú en la pantalla de TV, si el

disco tiene una función de menú.

En este caso, presione

, , , ó ENTER para

activar una función de menú.

Reproducción básica (DVD) Reproducción con avance rápido

Presione FWD durante la reproducción normal.

Cada vez que presione el botón de FWD, aumentará la

velocidad de la búsqueda.

•

Para seguir con la reproducción normal, presione PLAY.

Reproducción con retroceso rápido

Presione REW durante la reproducción normal.

Cada vez que presione el botón de REW, aumentará la

velocidad de la búsqueda.

•

Para seguir con la reproducción normal, presione PLAY.

Reproducción Fija

Avance cuadro por cuadro

Presione PAUSE/STILL durante la imagen fija.

Avanza un cuadro cuando presione PAUSE/STILL una vez.

• Para seguir con la reproducción normal, presione PLAY.

• Para volver a la imagen fija, presione PAUSE/STILL.

Presione SLOW( ) durante la reproducción normal o

cuadro a cuadro.

Cada vez que presione el botón de SLOW, cambiará la

velocidad del slow.

PLAY

SET

–

ENTER

PLAY

FWD

PLAY

REW

PLAY

SLOW

PLAY

2C53607A (SP) Q Sheet 11/3/04, 6:317

Pulse SKIP o varias veces para visualizar

el capítulo o la pista que desee.

Coloque las pilas

Coloque dos pilas

“

AAA

”

, (suministradas) prestando

atención a las marcas de polaridad en el compartimiento

de las pilas.

Deslice la tapa del compartimento de las pilas

siguiendo la dirección de la flecha.

Recoloque la tapa del compartimiento.

J2C53607A U

La ley prohibe copiar, difundir, mostrar, emitir por cable, reproducir

en público, y alquilar sin permiso material con derechos de autor

reservados (copyright).

Este dispositivo no graba en cinta DVDs protegidos contra copias.

El dispositivo no ha de utilizarse para copiar contenidos bajo

derechos de autor.

La obtención de tal permiso es responsabilidad exclusiva del

usuario.

Este producto incorpora la tecnología de protección de derechos de

autor (Copyright) mediante un método que protege ciertas patentes

de EE.UU. y otros derechos de propiedad intelectual pertenecientes

a Macrovision Corporation y otros propietarios de derechos. La

utilización de esta tecnología de protección deberá ser autorizada

por Macrovision Corporation, y tiene como fin la utilización en el

hogar y otros usos de contemplación limitados a menos que

Macrovision Corporation autorice otra cosa. Está prohibido modificar

esta ingeniería y desmontar la unidad.

Fabricado bajo licencia de Dolby Laboratories.

“Dolby”, “Pro Logic” y el símbolo de la doble D son marcas comerciales de

Dolby Laboratories.

Notas sobre los derechos de autor

Búsqueda de un capítulo o canción

INDEX

SKIP

INDEX

SKIP

–

Funciones básicas del control remoto

• Presione POWER ( ) para encender o apagar el DVD/

VCR.

• Seleccione su modo operativo deseado (DVD o VCR)

utilizando VCR DVD.

El indicador DVD o VCR del panel frontal le mostrará qué

modo está seleccionado.

• Presione CH + o CH – para desplazarse por los canales

uno a la vez.

•CH +/– (

/ ) y SET +/– ( / ) se utilizan también

para navegar por el sistema de menús en pantalla.

• Los botones de número permiten acceder directamente

a canales concretos.

• Cada vez que se presiona VCR DVD en el control

remoto, la pantalla alterna entre la pantalla VCR (modo

VCR) y la pantalla DVD (modo DVD).

Funcionamiento

• Apunte el mando a distancia al sensor remoto y presione

los botones de control para hacer funcionar.

• Utilice el control remoto dentro de un ángulo de 30˚ hacia

ambos lados del sensor remoto, hasta una distancia de

unos 7 metros.

La reproducción se inicia desde el capítulo o la pista

que haya seleccionado.

Para localizar capítulos o pistas

subsiguientes.

La reproducción se inicia desde el principio

del capítulo o pista actual.

Si se pulsa dos veces, la reproducción se

inicia desde el principio del capítulo o pista

anterior.

2C53607A (SP) Q Sheet 11/3/04, 6:318

Dolby Laboratories DVD960/P02 Manual de usuario

Marca: Dolby Laboratories

Modelo: DVD960/P02

Categoría: Reproductores de DVD

Tipo: Manual de usuario

Descargar PDF

informe

En otros idiomas

English: Dolby Laboratories DVD960/P02 User manual

Dolby Laboratories DVD960/P02 Manual de usuario

Dolby Laboratories DVD960/P02 Manual de usuario

En otros idiomas

Otros documentos