Nilfisk-Advance 56507004 Manual de usuario

Marca: Nilfisk-Advance

Modelo: 56507004

Categoría: Máquina de piso

Tipo: Manual de usuario

Exterra™

11/06 revised 5/08 Form No. 56041656

SR 1900

A-English

B-Español

Instructions For Use / Instrucciones de uso

Advance Models: 56507000 (3 cyl LPG), 56507001 (3 cyl Petrol)

56507003, 56307252 (4 cyl LPG), 56507004 (4 cyl Petrol), 56507005 (4 cyl Diesel)

56508639 (4 cyl LPG / cab), 56508640 (4 cyl Petrol / cab), 56508641 (4 cyl Diesel / cab)

Nilﬁ sk Models: 56507009 (4 cyl LPG), 56507010 (4 cyl Petrol), 56507011 (4 cyl Diesel)

56508769 (4 cyl LPG / cab), 56508770 (4 cyl Petrol / cab), 56508771 (4 cyl Diesel / cab)

A-2 / ENGLISH

A-2 - FORM NO. 56041656 - Exterra™ / SR 1900

TABLE OF CONTENTS

Page

Introduction ................................................................................A-3

Parts and Service ......................................................................A-3

Nameplate .................................................................................A-3

Uncrating the Machine ...............................................................A-3

Cautions and Warnings .............................................................A-4

Consignes de prudence et de sécurité ......................................A-5

General Information ...................................................................A-6

Know Your Machine..................................................... A-8 – A-11

Preparing the Machine for Use

Pre-Operational Checklist ........................................................A-12

Main Broom .............................................................................A-12

Fuel ..........................................................................................A-12

Operating the Machine

Before Starting the Machine ....................................................A-13

Starting the Diesel Engine .......................................................A-13

Starting the Gasoline Engine ...................................................A-13

Starting the Propane Engine ...................................................A-13

Sweeping .................................................................................A-14

Emptying the Hopper ...............................................................A-14

After Using the Machine

After Use ..................................................................................A-15

Shutting Down the Diesel / Gasoline Engine ...........................A-15

Shutting Down the Propane Engine ........................................A-15

Maintenance

Maintenance Schedule ............................................................A-15

Main Broom Maintenance ........................................................A-16

Side Broom Maintenance ........................................................A-18

Hopper Dust Control Filter .......................................................A-20

Hydraulic Oil ............................................................................A-21

Engine Oil ................................................................................A-21

Engine Coolant ........................................................................A-21

Engine Air Filter .......................................................................A-21

Circuit Breaker Location ..........................................................A-22

Troubleshooting .......................................................................A-23

Technical Speciﬁ cations ..........................................................A-25

ENGLISH / A-3

FORM NO. 56041656 - Exterra™ / SR 1900 - A-3

INTRODUCTION

This manual will help you get the most from your Nilﬁ sk-Advance Sweeper. Read it thoroughly before operating the machine.

Note: Bold numbers in parentheses indicate an item illustrated on pages 8-11.

PARTS AND SERVICE

Repairs, when required, should be performed by Nilﬁ sk-Advance service personnel using Nilﬁ sk-Advance original replacement parts and

accessories.

Call Nilﬁ sk-Advance for repair parts or service. Please specify the Model and Serial Number when discussing your machine.

NAME PLATE

The Model and Serial Number of your machine are shown on the Nameplate on the right side of the machine. This information is needed when

ordering repair parts for the machine. Use the space below to note the Model and Serial Number of your machine for future reference.

MODEL ________________________________________________

SERIAL NUMBER _______________________________________

UNCRATING THE MACHINE

Upon delivery, carefully inspect the shipping crate and the machine for damage. If damage is evident, save all parts of the shipping crate so that

they can be inspected by the trucking company that delivered the machine. Contact the trucking company immediately to ﬁ le a freight damage

claim.

1 After removing the crate, remove the wooden blocks next to the wheels.

2 Check the engine oil and coolant levels.

3 Check the hydraulic oil level.

4 Read the instructions in the Preparing the Machine For Use section of this manual, then ﬁ ll the fuel tank.

6 Place a ramp next to the front end of the pallet.

7 Read the instructions in the Operating Controls and Operating the Machine sections of this manual and start the engine. Slowly drive the

machine forward down the ramp to the ﬂ oor. Keep your foot lightly on the brake pedal until the machine is off the pallet.

CAUTION!

Use extreme CAUTION when operating this sweeper. Be certain that you are thoroughly familiar with all of the operating instructions

prior to using this sweeper. If you have any questions, contact your supervisor or your local Nilﬁ sk-Advance Industrial Dealer.

Should your sweeper malfunction, do not attempt to correct the problem unless your supervisor directs you to do so. Have a

qualiﬁ ed company mechanic or an authorized Nilﬁ sk-Advance Dealer Service person make any necessary corrections to the

equipment.

Use extreme care when working on this machine. Neckties, loose clothing, long hair, rings and bracelets can get caught in moving

parts. Turn the Key Switch (TT) OFF, remove the Key, set the Parking Brake (F) and disconnect the battery before working on the

machine. Use good common sense, practice good safety habits and pay attention to the yellow decals on this machine.

Drive the machine slowly on inclines. Use the Brake Pedal (F) to control machine speed while descending inclines. DO NOT turn

the machine on an incline; drive straight up or down.

The maximum rated incline during transport with a 3 cylinder model is 15%.

The maximum rated incline during transport with a 4 cylinder model is 24%.

* Note: Reference the separately supplied engine manufacturer’s maintenance and operator manual for more detailed engine

speciﬁ cation and service data.

All references to 3 cylinder models apply to Advance branded models only. There are no 3 cylinder Nilﬁ sk branded models.

revised 8/07

A-4 / ENGLISH

A-4 - FORM NO. 56041656 - Exterra™ / SR 1900

CAUTIONS AND WARNINGS

SYMBOLS

Nilﬁ sk-Advance uses the symbols below to signal potentially dangerous conditions. Always read this information carefully and take

the necessary steps to protect personnel and property.

DANGER!

Is used to warn of immediate hazards that will cause severe personal injury or death.

WARNING!

Is used to call attention to a situation that could cause severe personal injury.

CAUTION!

Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property.

Read all instructions before using.

GENERAL SAFETY INSTRUCTIONS

Speciﬁ c Cautions and Warnings are included to warn you of potential danger of machine damage or bodily harm.

DANGER!

* This machine emits exhaust gases (carbon monoxide) that can cause serious injury or death, always provide adequate

ventilation when using machine.

WARNING!

* This machine shall be used only by properly trained and authorized persons.

* While on ramps or inclines, avoid sudden stops when loaded. Avoid abrupt sharp turns. Use low speed down hills. Clean only

while ascending (driving up) the ramp.

* To avoid hydraulic oil injection or injury always wear appropriate clothing and eye protection when working with or near hydraulic

system.

* Turn the key switch off (O) and disconnect the batteries before servicing electrical components.

* Never work under a machine without safety blocks or stands to support the machine.

* Do not dispense ﬂ ammable cleaning agents, operate the machine on or near these agents, or operate in areas where ﬂ ammable

liquids exist.

* Only use the brushes provided with the appliance or those speciﬁ ed in the instruction manual. The use of other brushes may

impair safety.

CAUTION!

* This machine is not approved for use on public paths or roads.

* This machine is only approved for hard surface use.

* This machine is not suitable for picking up hazardous dust.

* When operating this machine, ensure that third parties, particularly children, are not endangered.

* Before performing any service function, carefully read all instructions pertaining to that function.

* Do not leave the machine unattended without ﬁ rst turning the key switch off (O), removing the key and applying the parking

brake.

* Turn the key switch off (O) and remove the key, before changing the brushes, and before opening any access panels.

* Take precautions to prevent hair, jewelry, or loose clothing from becoming caught in moving parts.

* Before use, all doors and hoods should be properly latched.

* Do not use on surfaces having a gradient exceeding that marked on the machine.

* All doors and covers are to be positioned as indicated in the instruction manual before using the machine.

SAVE THESE INSTRUCTIONS

revised 3/07

ENGLISH / A-5

FORM NO. 56041656 - Exterra™ / SR 1900 - A-5

CONSIGNES DE PRUDENCE ET DE SECURITE

SYMBOLES

Nilﬁ sk-Advance utilise les symboles reproduits ci-dessous pour attirer l’attention de l’opérateur sur des situations potentiellement dangereuses. Il

est donc conseillé de lire attentivement ces indications et de prendre les mesures adéquates en vue de protéger le personnel et le matériel.

DANGER !

Ce symbole est utilisé pour mettre l’opérateur en garde contre les risques immédiats pouvant provoquer des dommages corporels graves, voire

entraîner la mort.

ATTENTION !

Ce symbole est utilisé pour attirer l’attention sur une situation susceptible d’entraîner des dommages corporels graves.

PRUDENCE !

Ce symbole est utilisé pour attirer l’attention de l’opérateur sur une situation qui pourrait entraîner des dommages corporels minimes ou des

dommages à la machine ou à d’autres équipements.

Veuillez lire toutes les instructions avant d’utiliser l’appareil.

CONSIGNES GENERALES DE SECURITE

Les consignes spéciﬁ ques de prudence et de sécurité mentionnées ici ont pour but de vous informer de la survenance de tout risque de

dommages matériels ou corporels.

DANGER !

* Les gaz d’échappement (monoxyde de carbone) évacués par la machine peuvent entraîner de graves dommages corporels, voire la mort.

Veillez donc toujours à bénéﬁ cier d’une ventilation sufﬁ sante lorsque vous utilisez la machine.

ATTENTION !

* Cette machine ne pourra être utilisée que par du personnel parfaitement entraîné et dûment autorisé.

* Evitez les arrêts subits lorsque la machine est chargée et se trouve sur des rampes ou des plans inclinés. Evitez les virages serrés. Adoptez

une vitesse réduite lorsque la machine est en descente. Ne nettoyez que lorsque la machine monte la pente.

* Lorsque vous utilisez le système hydraulique ou travaillez à proximité de celui-ci, veillez à porter une tenue appropriée et des lunettes de

protection aﬁ n d’éviter tout risque de blessures ou toute projection d’huile.

* Positionnez la clé de contact sur off (O) et déconnectez les batteries avant de procéder à l’entretien des composants électriques.

* Ne travaillez jamais sous une machine sans y avoir placé, au préalable, des blocs de sécurité ou des étais destinés à soutenir la machine

* Ne déversez pas d’agents nettoyants inﬂ ammables, ne faites pas fonctionner la machine à proximité de ces agents ou d’autres liquides

inﬂ ammables.

* Utilisez uniquement les brosses fournies avec l’appareil ou celles spéciﬁ ées dans le manuel d’instructions. L’utilisation d’autres brosses peut

mettre la sécurité en péril.

PRUDENCE !

* Cette machine n’est pas conçue pour une utilisation sur les chemins ou voies publiques.

* Cette machine est seulement approuvée pour l’usage extérieur dur.

* Cette machine n’est pas conçue pour le ramassage des poussières dangereuses.

* Lors de l’utilisation de cette machine, assurez-vous que des tiers, et notamment des enfants, ne courent pas le moindre risque.

* Avant de procéder à toute opération d’entretien, veuillez lire attentivement toutes les instructions qui s’y rapportent.

* Ne laissez pas la machine sans surveillance sans avoir, au préalable, coupé le contact, enlevé la clé de contact (O) et tiré le frein à main.

* Positionnez la clé de contact sur off (O) avant de remplacer les brosses ou d’ouvrir tout panneau d’accès.

* Prenez toutes les mesures nécessaires pour éviter que les cheveux, les bijoux ou les vêtements amples ne soient entraînés dans les parties

mobiles de la machine.

* Avant utilisation, toutes les portes et capots doivent être correctement fermés.

* N’utilisez pas sur des surfaces dont la pente dépasse celle mentionnée sur la machine.

* Toutes les portes et couvercles doivent être dans la position mentionnée dans le manuel d’instruction avant de mettre la machine en service.

CONSERVEZ SOIGNEUSEMENT CES INSTRUCTIONS

revised 3/07

A-6 / ENGLISH

A-6 - FORM NO. 56041656 - Exterra™ / SR 1900

HOPPER SAFETY SUPPORT

WARNING!

Make sure the Hopper Safety Support (5) is in place whenever attempting to do any maintenance work under or near the raised

hopper. The Hopper Safety Support (5) holds the hopper in the raised position to allow work to be performed under the hopper.

NEVER rely on the machine’s hydraulic components to safely support the hopper.

JACKING THE MACHINE

CAUTION!

Never work under a machine without safety stands or blocks to support the machine.

• When jacking the machine, do so at designated locations (Do Not jack on the hopper) - see jacking locations (8).

TRANSPORTING THE MACHINE

CAUTION!

Before transporting the machine on an open truck or trailer, make sure that...

• All access doors are latched securely

• The machine is tied down securely.

• The machine parking brake is set.

TOWING OR PUSHING A DISABLED MACHINE

The machine’s drive propelling pump is manufactured with an adjustable tow valve. This valve prevents damage to the hydraulic system when the

machine is being towed/pushed short distances without use of the engine.

To access the valve open the Engine Compartment Cover (1) and locate the hydrostatic pump at the rear of the engine. The top half the

illustration on the following page shows the location on 3 cylinder models and the bottom half shows the 4 cylinder model location. Turn the valve

90 degrees, this disengages the hydrostatic lock between the motor and pump.

WARNING: The hydraulic propelling pump can be damaged if the machine is towed with the valve in the normal working position (A). Reference

the illustration on the following page for the normal working setting (A) (vertical) and the free wheeling towing setting (B) (horizontal). Note: If the

tow valve is left in free wheeling (B) (horizontal) position the propelling pump can’t drive the machine FWD or REV. No damage will result, just

re-set valve to the normal working setting (A) (vertical). NOTE: Tow or push machine no faster than a normal walking pace (2-3 miles per hour)

and for short distances only. If the machine is to be moved long distances the drive wheel needs to be raised off the ﬂ oor and placed on a suitable

transport dolly.

ENGLISH / A-7

FORM NO. 56041656 - Exterra™ / SR 1900 - A-7

3 CYLINDER MODELS

4 CYLINDER MODELS

A-8 / ENGLISH

A-8 - FORM NO. 56041656 - Exterra™ / SR 1900

KNOW YOUR MACHINE

As you read this manual, you will occasionally run across a bold number in parentheses - example: (2). These numbers refer to an item on the

next four pages. Refer back to these pages whenever necessary to pinpoint the location of an item mentioned in the text.

1 Engine Compartment Cover

2 Left Side Main Broom Access Panel

3 Battery

4 Center Cover Assembly

5 Hopper Safety Support

6 Hopper Cover Latch

7 Head Light

8 Jacking Locations (rear location is large weight below radiator)

9 Side Broom

10 Side Broom Height Adjustment Knob

11 Dust Filter Shaker Assembly

12 Hopper Dust Control Filter

European models use a maintenance free bag type ﬁ ltration system not shown here

13 Shaker Assembly Retainer Knobs

14 Hydraulic Oil Filter

15 Coolant Recovery Tank (4 cylinder location)

revised 8/07

ENGLISH / A-9

FORM NO. 56041656 - Exterra™ / SR 1900 - A-9

KNOW YOUR MACHINE (CONTINUED)

16 Hopper Cover

17 Hopper Cover Prop Rod

18 Right Side Main Broom Access Panel

19 Oil Reservoir

20 Oil Reservoir / Fuel Tank Cover

21 Fuel Tank (LPG tank shown / Gasoline tank is in same location)

22 Coolant Recovery Tank (3 cylinder & diesel location)

23 Radiator Cap

24 Engine Air Filter (3 cylinder & diesel location)

25 Fuel Tank Cover Release Latch

26 Tie-Down Locations (5)

27 Air Filter Service Indicator

28 Engine Air Filter (4 cylinder location)

revised 8/07

A-10 / ENGLISH

A-10 - FORM NO. 56041656 - Exterra™ / SR 1900

OPERATOR’S COMPARTMENT

A Operator’s Seat

B Main Broom Lever

C Main Broom Adjust Knob

D Control Panel (See Associated Pages)

E Steering Wheel

F Brake Pedal / Parking Brake

G FWD / REV Drive Pedal

H Circuit Breaker Panel

I Hopper Safety Support Handle

J Operator Seat Adjustment Lever

K Choke Cable (3 Cylinder)

ENGLISH / A-11

FORM NO. 56041656 - Exterra™ / SR 1900 - A-11

CONTROL PANEL

AA Fuel Gauge (Gasoline and Diesel Only)

BB Horn Switch

CC PROPANE Low Indicator Light

DD Headlight Switch

EE Engine Service Indicator (4 cylinder)

FF Glow Plug Indicator Light (Diesel Only)

GG Engine Speed Switch

HH Side Broom ON-Down / OFF-Up Switch

II Dust Control Indicator

JJ Dust Control Switch

KK Plugged Filter Indicator

LL Shaker Switch

MM Hopper UP Indicator

NN Open Dump Door Switch

OO Hopper Overtemp Indicator

PP Close Dump Door Switch

QQ Lower Hopper Switch

RR Raise Hopper Switch

SS Hour Meter

TT Ignition Switch

UU Service Indicator Light

revised 8/07

A-12 / ENGLISH

A-12 - FORM NO. 56041656 - Exterra™ / SR 1900

PRE-OPERATIONAL CHECKLIST

Before Each Use:

* Inspect the machine for damage, oil or coolant leaks.

* Squeeze the rubber dust cup on the Engine Air Filter (24) to release built-up dust.

* Check the engine coolant level (23).

* Check the engine oil level.

* Check the hydraulic oil level (19).

* Check the Fuel Gauge (AA) on the gasoline and diesel models.

* Check the Fuel Gauge located on the PROPANE tank (21) for PROPANE model.

* Check the tire pressure of all three tires, should be 90-95 psi.

* Check the Air Filter Service Indicator.

In the Driver’s Seat:

* Be sure that you understand the operating controls and their functions.

* Adjust the seat to allow easy reach of all controls.

* Insert the Master Key and turn the Ignition Switch (TT) to the ON position. Check for proper operation of the Horn (BB), Hour Meter (SS) and

Headlights (DD). Turn the Ignition Key Switch (TT) OFF.

* Check the Parking Brake (F). The brake must hold its (locked parked) setting ﬁ rmly with out easily being released.

(Report all defects immediately to service personnel).

Plan Your Cleaning in Advance:

* Arrange long runs with a minimum of stopping or starting.

* Allow 6 inches of broom path overlap to ensure complete coverage.

* Avoid making sharp turns, bumping into posts, or scraping the side of the machine.

MAIN BROOM

Several different main brooms are available for this machine. Contact your Nilﬁ sk-Advance dealer if you need help selecting the best broom for the

surface and litter that you will be sweeping. Note: Reference broom maintenance for installation steps.

FUEL

WARNING !

• ALWAYS STOP THE ENGINE BEFORE FILLING THE FUEL TANK.

• DO NOT SMOKE WHILE FILLING THE FUEL TANK.

• FILL THE FUEL TANK IN A WELL-VENTILATED AREA.

• DO NOT FILL THE FUEL TANK NEAR SPARKS OR OPEN FLAME.

• USE ONLY THE FUEL SPECIFIED ON THE FUEL TANK DECAL.

DIESEL ENGINE

Fill the tank with Number 2 Diesel Fuel if the machine will be used in an area where the temperature is 30° Fahrenheit (0° Celsius) or higher. Use

Number 1 Diesel Fuel if the machine will be used in an area where the temperature is below 30° Fahrenheit (0° Celsius).

NOTE: If the diesel machine runs out of fuel completely, the fuel system must be bled before the engine can be re-started. To avoid this situation,

ﬁ ll the fuel tank when the fuel gauge indicates 1/4 tank. Fuel tank capacity is 12.75 gallons (48.26 liters).

GASOLINE ENGINE

FILL THE TANK WITH UNLEADED 87 OCTANE REGULAR GASOLINE. FUEL TANK CAPACITY IS 12.75 GALLONS (48.26 LITERS).

Note: Reference the separately supplied engine manufacture’s maintenance and operator manual for more detailed engine speciﬁ cation and

service data.

PROPANE ENGINE

Mount a standard 33 lb. liquid withdrawal propane tank on the machine, connect the fuel hose and open the shutoff valve on the tank. Wear

gloves when connecting or disconnecting the fuel hose. Shut the propane tank service valve OFF when the machine is not in use.

NOTE: Make sure to properly orient the horizontal LPG tank for liquid withdrawal. After connecting the fuel hose to the tank check for leaks by

listening and smelling for gas.

WARNING!

Do not operate the machine if a gas leak is present. Disconnect the fuel hose and replace the LPG tank. If a gas leak is still present

disconnect the fuel hose and contact your Nilﬁ sk-Advance Service Center.

ENGLISH / A-13

FORM NO. 56041656 - Exterra™ / SR 1900 - A-13

OPERATING THE MACHINE

The Exterra™ / SR 1900 is a rider-type automatic ﬂ oor sweeping machine. The controls were designed with one touch operation in mind. For

single pass sweeping the operator can simply lower the main broom and all sweeping functions will be ready to go.

Note: Bold numbers in parentheses indicate an item illustrated on pages 8-11.

BEFORE STARTING THE MACHINE

1 Be sure you understand all machine controls and their functions.

2 Plan your cleaning route. Arrange long, straight passes with as few turns as possible.

3 Check the Brake Pedal (FF). The pedal should be ﬁ rm.

If the pedal is “spongy” or fades under pressure, DO NOT DRIVE THE MACHINE. Report all defects immediately to service personnel.

STARTING THE DIESEL ENGINE

1 Turn the Key Switch (TT) counter-clockwise to the “Pre-Heat” position and hold it there until the Glow Plug Indicator (FF) turns OFF. Once

the indicator turns OFF the engine can be started. Skip this step if the engine has been running and is already warm.

2 Turn the Key Ignition Switch (TT) clockwise to the START position and release it as soon as the engine starts. If the engine does not start

after cranking for 15 seconds, release the key, wait for 1 minute and try steps 1-3 again.

3 Let the engine run at “IDLE” speed for 5 minutes before using the machine.

4 Push the Engine Speed Switch (GG) to switch to “FULL THROTTLE” and move the machine around for 2 or 3 minutes at a slow speed to

warm up the hydraulic system.

STARTING THE PROPANE / GASOLINE ENGINE

1 NOTE: Propane models only: Open the service valve on the LP fuel tank (21).

2 NOTE: 3 Cylinder models: Pull the Choke Knob all the way out. (Skip this step if the engine has been running and is already warm.)

3 Turn the Ignition Key Switch (TT) clockwise to the START position and release it as soon as the engine starts. If the engine does not start

after cranking for 15 seconds, release the key, wait for 1 minute, then try again.

4 NOTE: 3 Cylinder models: Once started, push the Choke Knob in slowly until the engine runs smoothly.

5 Let the engine run at “IDLE” speed for 5 minutes before using the machine.

NOTE: 3 Cylinder models: Push the Choke Knob all the way in.

6 Push the Engine Speed Switch (GG) to switch to “FULL THROTTLE” and move the machine around for 2 or 3 minutes at a slow speed to

warm up the hydraulic system.

NOTE: ALWAYS operate the machine with the Throttle Control at full throttle. Use the Forward/Reverse Pedal (G) - not the Throttle

Control - to control the speed of the machine. The speed of the machine will increase as the pedal is pushed closer to the ﬂ oor. Do not press the

Forward/Reverse Pedal until the engine has started, this will disengage the starter.

A-14 / ENGLISH

A-14 - FORM NO. 56041656 - Exterra™ / SR 1900

SWEEPING

Follow the instructions in the preparing the machine for use section of the manual.

1 While seated on the machine, adjust the seat to a comfortable operating position using the adjustment controls (J).

2 Release the Parking Brake (F). To transport the machine to the work area, apply even pressure with your foot on the front of the Drive Pedal

(G) to go forward or the rear of the pedal for reverse. Vary the pressure on the foot pedal to obtain the desired speed.

3 Push the Lower Hopper Switch (QQ) to make sure the hopper is seated properly.

4 Move the Main Broom Lever (B) to the SWEEP (middle notch) position to lower and enable the main broom. NOTE: The dump door opens

automatically when the main broom (B) is lowered and closes when the broom is raised.

Use the FULL FLOAT (last notch forward) position only when sweeping extremely rough or uneven ﬂ oors. Use at other times will only

increase broom wear.

5 When sweeping ﬂ oors with puddles, push the Dust Control Switch (JJ) to turn OFF the dust control system before the machine enters a

puddle. Turn the dust control system back ON when the machine is back on completely dry ﬂ oor.

When sweeping wet ﬂ oors, keep the Dust Control Switch (JJ) OFF at all times.

6 The Side Broom (9) is automatically enabled when the main broom is lowered and starts spinning when the Drive Pedal (G) is activated. The

Side Broom (9) can be turned off and back on at any time by pushing the Side Broom Switch (HH).

The side broom sweeping pattern is adjusted by turning the Side Broom Height Adjustment Knob (10).

7 Drive the machine straight forward at a quick walking speed. Drive the machine slower when sweeping large amounts of dust or debris or

when safe operation dictates slower speeds. Overlap passes 6 inches (15 cm).

8 If dust comes out of the broom housing while sweeping, the Dust Control Filter (12) may be clogged. Push the Shaker Switch (LL) to clean

the dust control ﬁ lter. The dust control system (JJ) will automatically turn OFF while the shaker is running and turn ON after the shaker turns

OFF (the shaker runs for 15 seconds).

9 Check behind the machine occasionally to make sure that the machine is picking up debris. Dirt left behind in the path of the machine usually

indicates that the machine is moving too fast, the broom needs to be adjusted, or the hopper is full.

EMPTYING THE HOPPER

WARNING!

Make sure the Hopper Safety Support (5) is in place whenever attempting to do any maintenance work under or near the raised

hopper. The Hopper Safety Support (5) holds the hopper in the raised position to allow work to be performed under the hopper.

NEVER rely on the machine’s hydraulic components to safely support the hopper.

NOTE: The MINIMUM ceiling height dumping clearance required for raising the hopper is 102” (259.08 cm)

1 Put the Main Broom Lever (B) in the UP / OFF position. NOTE: The Shaker will automatically run for about 15 seconds after the main broom

is raised.

2 If you do not raise the main broom, push the Shaker Switch (LL) to remove excess dirt from the dust control ﬁ lter. SERVICE NOTE: For

best shaker performance always run the shaker with the hopper fully down.

3 Drive the machine close to a large trash receptacle and hold the Raise Hopper Switch (RR) until the hopper is all the way up. NOTE: The

dump door automatically closes when switch (RR) is pushed. You regain control of the dump door as soon as the hopper begins to raise so

you can dump at any height if necessary.

4 Move the machine forward until the hopper is over the receptacle and set the Parking Brake (F). Press the Open Dump Door Switch (NN) to

open the dump door and empty the hopper. NOTE: If not dumping into a trash receptacle, low dumping is recommended to help eliminate

airborne dust.

5 Put the Hopper Safety Support (5) in place by pulling back on the Hopper Safety Support Pull Rod (I), then lower the hopper slightly to

secure.

6 Check the hopper door and the front edge seal. Use a broom, if necessary, to remove litter from these areas. The hopper door must seal

tightly against the broom housing bulb gasket for proper operation.

7 Return to the operator’s compartment. Release the parking brake. Move the machine back until the hopper will clear the receptacle. Raise

the hopper slightly and push forward on the Hopper Safety Support Handle (I) until the Hopper Safety Support (5) disengages, then lower the

hopper. NOTE: The brooms will not turn on if the hopper is not completely down. The indicator light (MM) on the control panel should turn

OFF indicating that the machine is ready for use.

ENGLISH / A-15

FORM NO. 56041656 - Exterra™ / SR 1900 - A-15

AFTER USE

1 Shake the Hopper Dust Control Filter (LL) and empty the hopper.

2 Check the maintenance schedule and perform all required maintenance before storage.

3 Move the machine to an indoor storage area.

4 Shut down the engine according to the shut down procedures.

5 Make sure the Ignition Switch (TT) is OFF and the Parking Brake (F) is engaged.

NOTE: It is safe to clean this machine with a pressure washer as long as you do not spray directly at or into electrical components. The machine should always

be allowed to dry completely before each use.

TO SHUT DOWN THE DIESEL / GASOLINE ENGINE...

1 Turn all controls to the OFF position.

2 Raise the brooms.

3 Place the Engine Speed Switch (GG) in IDLE and let the engine idle for 25 - 30 seconds.

4 Turn the Ignition Key Switch (TT) OFF and remove the key. NOTE: The 4 cylinder gasoline engine will continue to run for a few seconds after switching the

key to off. This is part of the proper operation of the closed loop electronic control system.

5 Apply the Parking Brake (F).

TO SHUT DOWN THE PROPANE ENGINE...

1 Turn all controls to the OFF position.

2 Raise the brooms.

3 Turn the service valve on PROPANE Tank (21) OFF.

4 Run the engine until all the PROPANE is dispelled from the line (the engine will stall).

5 Turn the Ignition Key Switch (TT) OFF and remove the key. NOTE: The 4 cylinder LPG engine will continue to run for a few seconds after switching the key

to off. This is part of the proper operation of the closed loop electronic control system.

6 Apply the Parking Brake (F).

REPORT ANY DEFECT OR MALFUNCTION NOTED DURING OPERATION TO AUTHORIZED SERVICE OR MAINTENANCE PERSONNEL.

MAINTENANCE

Make sure that the machine is kept in top shape by following the maintenance schedule closely. Repairs, when required, should be performed by your Authorized

Nilﬁ sk-Advance Service Center, who employs factory trained service personnel and maintains an inventory of Nilﬁ sk-Advance Original Equipment Replacement

Parts and Accessories.

NOTE: Refer to the Service Manual for more detail on maintenance and service repairs.

MAINTENANCE SCHEDULE

Maintenance intervals given are for average operating conditions. Machines used in severe operational environments may require service more often.

MAINTENANCE ITEM PERFORM DAILY

Perform the “After Use” maintenance steps X

Check parking brake X

Check engine oil X

*Clean main and side broom(s) X

Check ﬁ lter indicator and lights (hyd & air) X

Check engine coolant level X

Check hydraulic oil level X

MAINTENANCE ITEM 15 hrs. 30 hrs. 150 hrs. 300 hrs. 1000 hrs.

*Rotate main broom X

*Inspect/adjust brooms X

* Check / Clean Hopper Dust Control Filter Using Method “A” X

*Inspect broom housing skirts X

*Inspect hopper seals X

Clean radiator and oil cooler X

Perform engine maintenance X

*Inspect and grease steering spindle X

* Check / Clean Hopper Dust Control Filter Using Method “B” X

* Check / Clean Hopper Dust Control Filter Using Method “C” X

Change the hydraulic “charge” oil ﬁ lter X

Change reservoir hydraulic oil X

Flush the radiator X

Engine fuel ﬁ lter(s) X

*See the Mechanical Repair Service Manual for detailed maintenance information of systems listed. (Sweeping, Hopper, Steering, Dust Control). NOTE: Cleaning

the hopper dust control ﬁ lter is not required on models using the maintenance free bag ﬁ lter.

A-16 / ENGLISH

A-16 - FORM NO. 56041656 - Exterra™ / SR 1900

MAIN BROOM MAINTENANCE

Since the Main Broom Motor always turns in the same direction, the bristles on the broom eventually become curved, reducing sweeping

performance. Sweeping performance can be improved by removing the broom and turning it around (end-for-end). This procedure, known as

“rotating” the main broom, should be done once every 15 hours of operation. NOTE: This procedure does not apply to the optional chevron

broom.

The main broom should be replaced for optimal performance when the bristles are worn to a length of 2 inches (5.08 cm). The main broom stop

must be re-adjusted when the broom is replaced. NOTE: The main broom is functional to a bristle length of 1/2 inch (12.7mm)

NOTE: The machine should be stored with the Main Broom in the raised position.

WARNING!

The engine must not be running when performing this procedure.

To Rotate or Replace the Main Broom...

1 Turn the Ignition Switch (TT) OFF.

2 Put the Main Broom Lever (B) in the DOWN position.

3 Open the Right Side Main Broom Access Panel (18).

4 See Figure 1. Pivot the Idler Arm Assembly (A1) out of the main broom core. NOTE: The Idler Arm is held in place by the Right Side Main

Broom Access Panel (18).

5 Pull the Main Broom (A2) out of the broom housing and remove any string or wire wrapped around it. Also inspect the skirts at the front, back

and sides of the broom housing. The skirts should be replaced or adjusted if they are torn or worn to a height of more than 1/4 inch (6.35

mm) off the ground.

6 Turn the broom around (end-for-end) and slide it back into the broom housing. Make sure that the lugs on the broom core (left side) engage

the slots in the broom drive hub and that the broom is fully seated.

7 Swing the idler arm assembly back into the broom core. NOTE: Make sure the lugs on the idler arm engage the slots in the broom core

8 Close and latch the Right Side Main Broom Access Panel (18).

To Adjust the Main Broom Height...

1 Drive the machine to an area with a level ﬂ oor and set the parking brake.

2 Pull the Main Broom Lever (B) back and slide to the right and up to lower the main broom. DO NOT move the machine.

3 Lightly press the Drive Pedal (G) to start the main broom and let it run in place for 1 minute. This allows the broom to polish a “strip” on the

ﬂ oor. After 1 minute, raise the broom, release the parking brake and move the machine so that the polished strip is visible.

4 Inspect the polished strip on the ﬂ oor. If the strip is less than 2 inches (5.08 cm) or more than 3 inches (7.62cm) wide, the broom needs to be

adjusted.

5 To adjust, loosen the Knob (C) and slide forward or backward to lower or raise the Main Broom. The farther the Lever (B) travels forward in

the slot, the lower the Main Broom will be. Tighten Knob (C) after adjusting the position of the stop bracket.

6 Repeat steps 1-5 until the polished strip is 2-3 inches (5.08-7.62cm) wide.

The width of the polished strip should be the same at both ends of the broom. If the strip is tapered, move the machine to a different area

and repeat steps 1-5. If the polished strip is still tapered, contact your Nilﬁ sk-Advance Dealer for service.

ENGLISH / A-17

FORM NO. 56041656 - Exterra™ / SR 1900 - A-17

FIGURE 1

A-18 / ENGLISH

A-18 - FORM NO. 56041656 - Exterra™ / SR 1900

SIDE BROOM MAINTENANCE

To adjust the Side Broom...

1 Drive the machine to an area with a level ﬂ oor and set the parking brake.

2 Pull the Main Broom Lever (B) back and slide to the right and up to lower the main and side brooms.

3 See Figure 2. When in the Down position, the Side Broom (9) should be contacting the ﬂ oor from the 10 O’Clock (A1) to the 3 O’Clock (A2)

area shown.

4 If it requires adjustment, turn the Side Broom Height Adjustment Knob (10) either clockwise to raise or counter-clockwise to lower the side

broom.

NOTE: The machine should be stored with the Side Broom (9) in the raised position. The Side Broom (9) should be replaced when the bristles

are worn to a length of 3 inches (7.62 cm) or it becomes ineffective. The Side Broom height must be re-adjusted when ever the broom has been

replaced.

FIGURE 2

ENGLISH / A-19

FORM NO. 56041656 - Exterra™ / SR 1900 - A-19

FIGURE 3

SIDE BROOM MAINTENANCE

To replace the Side Broom...

1 See Figure 3. Raise the hopper until the side broom is approximately at chest height.

2 Grab hold of the side broom with both hands and rotate until the ring end of the Hitch Pin (A1) is facing toward the rear of the hopper. NOTE:

The side broom(s) will only rotate freely in one direction.

3 Remove the Hitch Pin (A1) and pull the Side Broom (A2) off of the motor shaft.

4 Slide the new broom onto the motor shaft, line up the pin hole and reinstall the Hitch Pin (A1).

A-20 / ENGLISH

A-20 - FORM NO. 56041656 - Exterra™ / SR 1900

HOPPER DUST CONTROL FILTER (PANEL FILTER)

The hopper dust control ﬁ lter must be cleaned regularly to maintain the efﬁ ciency of the vacuum system. Follow the recommended ﬁ lter service

intervals for the longest ﬁ lter life.

CAUTION!

Wear safety glasses when cleaning the ﬁ lter.

Do not puncture the paper ﬁ lter.

Clean the ﬁ lter in a well-ventilated area.

Wear appropriate dust mask to avoid breathing in dust.

To remove the hopper dust control ﬁ lter...

1 Unlatch and open the Hopper Cover (16). Make sure that the Hopper Cover Prop Rod (17) is in place.

2 Inspect the top of the Hopper Dust Control Filter (12) for damage. A large amount of dust on top of the ﬁ lter is usually caused by a hole in the

ﬁ lter or a damaged ﬁ lter gasket.

3 Remove the four Shaker Assembly Retainer Knobs (13). Lift off the Dust Filter Shaker Assembly (11) to access the panel ﬁ lter.

4 Lift the Hopper Dust Control Filter (12) out of the machine.

5 Clean the ﬁ lter using one of the methods below:

Method “A”

Vacuum loose dust from the ﬁ lter. Then gently tap the ﬁ lter against a ﬂ at surface (with the dirty side down) to remove loose dust and dirt.

NOTE: Take care not to damage the metal lip which extends past the gasket.

Method “B”

Vacuum loose dust from the ﬁ lter. Then blow compressed air (maximum pressure 100 psi) into the clean side of the ﬁ lter (in the opposite

direction of the airﬂ ow).

Method “C”

Vacuum loose dust from the ﬁ lter. Then soak the ﬁ lter in warm water for 15 minutes, then rinse it under a gentle stream of water (maximum

pressure 40 psi). Let the ﬁ lter dry completely before putting it back into the machine.

6 Follow the instructions in reverse order to install the ﬁ lter. If the gasket on the ﬁ lter is torn or missing, it must be replaced. NOTE: Before

replacing ﬁ lter clear debris from dust plate located under ﬁ lter. Verify that the debris ﬂ ap at the rear of the dust plate swings freely

HOPPER DUST CONTROL FILTER (OPTIONAL NILFISK POCKET FILTER SYSTEM)

The optional Nilﬁ sk pocket ﬁ lter system is basically maintenance free. The only periodic maintenance required by the machine operator is to run

the Shaker (LL) on a daily basis. NOTE: The shaker should only be run with the hopper in the down position.

revised 8/07

ENGLISH / A-21

FORM NO. 56041656 - Exterra™ / SR 1900 - A-21

HYDRAULIC OIL

Unlatch and swing open the Oil Reservoir / Fuel tank Cover (20). Remove the reservoir cap to check the oil level. The hydraulic oil level should

be half way up the screen ﬁ lter inside the ﬁ ller neck of the reservoir. Add SAE 10W30 motor oil if it is below this level. Change the oil if major

contamination from a mechanical failure occurs.

ENGINE OIL – GASOLINE (PETROL) & LPG

Check the engine oil level when the machine is parked on a level surface and the engine is cool. Change the engine oil after the ﬁ rst 35 hours of operation and

every 150 hours after that. Use any SF or SG rated oil meeting API speciﬁ cations and suited to seasonal temperatures. Refer to the Engine System section for oil

capacities and additional engine speciﬁ cations. Replace the oil ﬁ lter with every oil change.

TEMPERATURE RANGE OIL WEIGHT

Above 60° F (15° C) SAE 10W-30

Below 60° F (15° C) SAE 5W-30

ENGINE OIL - DIESEL

Check the engine oil level when the machine is parked on a level surface and the engine is cool. Change the engine oil after the ﬁ rst 35 hours of operation and

every 150 hours after that. Use CF, CF-4 or CG-4 oil meeting API speciﬁ cations and suited temperatures (*important reference the oil/fuel type note below for

further diesel oil recommendations). Refer to the Engine System section for oil capacities and additional engine speciﬁ cations. Replace the oil ﬁ lter with every oil

change.

TEMPERATURE RANGE OIL WEIGHT

Above 77 °F (25 °C) SAE 30 or 10W-30

32 °F to 77 °F (0 °C to 25 °C) SAE 20 or 10W-30

Below 32 °F (0 °C) SAE 10W or 10W-30

* Diesel Lubricating Oil Note:

With the emission control now in effect, the CF-4 and CG-4 lubricating oils have been developed for use of a low-sulfur fuel on-road vehicle engines. When

an off-road vehicle engine runs on a high-sulfur fuel, it is advisable to employ the CF, CD or CE lubricating oil with a high total base number. If the CF-4 or

CG-4 lubricating oil is used with a high-sulfur fuel, change the lubricating oil at shorter intervals.

• Lubricating oil recommended when a low-sulfur or high-sulfur fuel is employed.

Fuel

Lubricating

Oil class

Low sulfur

(0.5 % ≥)High sulfur Remarks

CF OO

TBN ≥ 10

CF-4 OX

CG-4 OX

O : Recommendable X : Not recommendable

ENGINE COOLANT

Open the Engine Compartment Cover (1) and observe the coolant level in the Coolant Recovery Tank (22). If the level is low, add a mixture of half

water and half automotive type anti-freeze.

CAUTION!

Do not remove the Radiator Cap (23) when the engine is hot.

ENGINE AIR FILTER

Check the Engine Air Filter Service Indicator (24) before each use of the machine. Do not service the air ﬁ lter unless the red ﬂ ag is visible in the

service indicator. NOTE: After cleaning or replacing the engine air ﬁ lter, the service indicator can be reset by pressing the end of the indicator.

CAUTION!

When servicing the engine air ﬁ lter elements, use extreme care to prevent loose dust from entering the engine. Dust can severely

damage the engine.

The engine air ﬁ lter contains a Primary (outer) and a Safety (inner) ﬁ lter element. The Primary Element may be cleaned twice before being

replaced. The Safety Element should be replaced every third time that the Primary Filter Element is replaced. Never attempt to clean the Inner

Safety Element.

To clean the Primary Filter Element, unsnap the 2 clips at the end of the air ﬁ lter and remove the end housing. Pull the primary element out. Clean

the element with compressed air (maximum pressure 100 psi) or wash it with water (maximum pressure 40 psi). DO NOT put the element back

into the canister until it is completely dry.

revised 5/08

A-22 / ENGLISH

A-22 - FORM NO. 56041656 - Exterra™ / SR 1900

CIRCUIT BREAKER LOCATION

CB1 Main (70A)

CB2 Headlights (20A)

CB3 Starter (15A)

CB4 Accessory (20A)

CB5 Ignition (10A)

CB6 Shaker (20A)

CB7 Turn Signals (20A)

CB8 Mister (10A)

CB9 HVAC (30A)

revised 8/07

ENGLISH / A-23

FORM NO. 56041656 - Exterra™ / SR 1900 - A-23

TROUBLESHOOTING

If the possible causes listed below are not the source of trouble, it is a symptom of something more serious. Contact your Nilﬁ sk-Advance Service

Center immediately for service.

TRIPPING THE CIRCUIT BREAKERS

The circuit breakers are located on the Circuit Breaker Panel (H), they protect electrical circuits and motors from damage due to overload

conditions. If a circuit breaker trips, try to determine the cause.

Main Circuit Breaker (CB1 / 70 Amp) Possible cause may be: