26cc-2 Cycle Grass Trimmer NPTGSS2617A

Bordeadora con motor de 2 tiempos de 26 cc NPTGSS2617A

Read all safety rules and instructions carefully before operating this tool.

601 Regent Park Court Greenville, SC 29607, SC 29650 1-866-384-8432

AVISO:

Utilice solo gasolina sin plomo que contenga máximo 10% de etanol. No utilice combustible E15 o E85 con esta bordeadora. Esto

violará la ley federal, dañará la bordeadora y anulará su garantía.

NOTICE:

Only use unleaded gasoline containing up to 10% ethanol. Do not use E15 or E85 fuel in this trimmer. It will violate the federal law,

CONTENTS

PRODUCT SPECIFICATIONS

GENERAL SAFETY RULES

SYMBOLS

KNOW YOUR GRASS TRIMMER

ASSEMBLY

BATTERY PACK AND CHARGER

OPERATION

MAINTENANCE

ENVIRONMENTALLY SAFE BATTERY DISPOSAL

NOTES

Section Page

2

2

3-6

7-8

9-10

11-13

14-15

16-22

23-30

39-40

Engine Size

Engine Displacement

Power / Speed

Idle Speed

Max Torque / Speed

Fuel Tank Capacity

Fuel / Oil Ratio

Line Diameter

Cutting Width

Charging Period (Battery Fully Discharged)

26cc

40 : 1

17" (432 mm)

4-6 Hours

PRODUCT SPECIFICATIONS

26cc-2 CYCLE GRASS TRIMMER

CONTENTS

2

GENERAL SAFETY RULES

READ ALL INSTRUCTIONS AND SAVE THESE INSTRUCTIONS.

Read the Operator’s Manual and follow all warnings and safety instructions. Failure to do so

can result in serious injury to the operator and/or bystanders.

■ This grass trimmer is designed for cutting grass, soft vegetation.

- In terms of composting.

■ Never allow children or persons unfamiliar with these instructions to use the trimmer.

■ Do not operate the trimmer inside a closed environment, such as a room or building; breathing

carbon monoxide from exhaust fumes can kill.

■ Clear the work area before each use. Remove all objects such as rocks, broken glass, nails,

wire, or string, which can be thrown or become entangled in the cutting attachment.

■ Clear the area of children, bystanders and pets. At a minimum, keep all children, bystanders

and pets outside a 50 ft (15 m) radius; outside the 50 ft (15 m) zone, there is still a risk of injury

from thrown objects.

■ Bystanders should be encouraged to wear eye protection. If you are approached, stop the

■ Do not operate this trimmer when you are tired, ill, upset, or under the influence of alcohol,

drugs, or medication.

■ Inspect the trimmer before each use. Replace damaged parts. Check for fuel leaks. Make sure

all fasteners are in place and secure.

■ Replace cutting attachment parts that are cracked, chipped, or damaged in any way. Make sure

the cutting attachment is properly installed and securely fastened. Be sure the cutting

attachment shield is properly attached, securely fastened and in the position recommended by

the manufacturer.

■ Use only a flexible, nonmetallic line recommended by the manufacturer. Never use, for

example, wire or wire-rope, which can break off and become a dangerous projectile.

3

■ Maintain stable footing on a solid surface at all times when using the trimmer in order to have

better control of the tool. Do not use the trimmer whilst on a ladder or other unstable support.

■ Keep cutting attachment below waist level. Keep all parts of your body away from the rotating

cutting attachment and hot surfaces.

■ Do not touch muffler, rear cover housing or casing around the engine; these parts get hot whilst

and after the trimmer has been used. Contact with hot surfaces could result in serious burns.

■ The cutting attachment should never rotate at idle during normal use.

■ The cutting attachment may be spinning during carburetor adjustments. Wear your protective

equipment and observe all safety instructions. For units equipped with a clutch, be sure the

cutting attachment stops turning when the engine idles. When the unit is turned off, make sure

■ Before fueling or storing the tool, stop the engine and allow it to cool completely.

■ Before transporting the tool in a vehicle, allow the engine to cool completely and empty the fuel

tank. Always secure the tool to avoid movement during transportation.

■ Only use replacement parts or accessories provided or listed in this Operator’s Manual.

■ This trimmer is not intended for extended use. Extended periods of operation can cause

circulatory problems in the user’s hands due to the vibration caused by the tool. Take regular

breaks from operating the tool.

■ Always take your tool to an authorized service center for repair. Service performed by inexperi-

enced or unqualified persons may damage the tool, create unsafe conditions, increase the risk

of personal injury, and/or void your warranty.

explosion and possibly injury.

■ Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause

damage to the eyes or skin. It may be toxic if swallowed.

GENERAL SAFETY RULES

■ Batteries can explode in the presence of a source of ignition, such as a pilot light. To reduce the

■ Under extreme usage or temperature conditions, battery pack leakage may occur. If liquid

■ When the battery pack is not in use, keep it away from other metal objects like: paper clips,

■ Follow all charging instructions and do not charge the battery pack outside the temperature

BATTERY CHARGER

■ This charger is only compatible with a 07LB2001-S lithium-ion battery.

■ To reduce the risk of injury, charge only the specified lithium-ion rechargeable batteries. Other

■ Do not charge the battery in a damp or wet location. Following this rule will reduce the risk of

■ Keep the cord and charger away from heat to prevent damage to housing or internal parts.

■ Do not abuse the charger cord. Never use the cord for carrying, pulling or unplugging.

■ Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords

5

GENERAL SAFETY RULES

■ A charger that is suitable for one type of battery pack may create a risk of fire when used with

6

7

16

17

18

19

20

21

filling and inspecting the tank. Check that the cap is sealed tightly and wipe clean any spillage

that may have occurred.

NOTICE: It is normal for smoke to be emitted from a new engine after first use.

FILLING THE FUEL TANK (See Fig. 10)

NOTICE: Before each use, ALWAYS shake the fuel container thoroughly to ensure that the fuel is

mixed completely.

■ Place the tool on a flat, level surface, outdoors.

■ Clean the area around the fuel tank and cap to prevent any contamination.

■ Loosen the fuel tank cap by turning it counter clockwise and remove (Fig. 10).

OPERATION

■ Make sure that the battery pack is securely in place.

■ Place the trimmer on a levelled surface, outdoors.

■ Press the primer bulb 5 times.

■ Turn the choke lever to the CHOKE position (Fig. 11).

■ Lift the start button cover and press the start button

until the engine starts. Then immediately engage the

throttle safety and the throttle trigger to start the

trimmer (Fig. 12-15). The choke lever will

automatically switch to RUN position.

■ If the choke lever is left on choke, the grass trimmer will stop running in 3-5 seconds.

up at idle for several minutes.

For warm start:

■ Make sure that the battery pack is securely in place.

■ Place the trimmer on a levelled surface, outdoors.

■ Press the primer bulb 5 times.

■ Make sure the choke lever in the RUN position.

OPERATION

In order to achieve optimum cutting results, only cut dry grass.

TRIMMING (See Fig. 18)

Fig. 17

Battery

indicator

■ Lift the start button cover and press the start button until the engine starts. Then immediately

engage the throttle safety and the throttle trigger to start the trimmer.

To stop the trimmer: Press the STOP switch to the stop position “O” until the trimmer stops (Fig.

16).

BATTERY INDICATOR (See Fig. 17)

cause possible serious injuries.

A - Direction-of-rotation

B - Dangerous cutting area

C - Best cutting area

■ Hold the grass trimmer firmly with both hands, keeping your right hand on the main handle and

left hand on the assist handle.

■ The trimmer should be held at a comfortable position with the rear handle at waist level (Fig.

against the ground as this can ruin the lawn and damage the product.

TRIMMING TIPS (See Figs. 18-19)

■ Keep the tool to the right side and away from your

body to avoid making contact with the hot surfaces

(Fig. 18).

■ Keep the trimmer head lowered, towards the area

being cut.

■ The straight shaft trimmer cuts best when moving the

unit from left to right. Passing the tool in this direction

will reduce the amount of debris thrown towards the

and walls made of metal, wood, stone and brick.

Avoid using the trimmer against these materials.

■ Stop the engine if the grass becomes wrapped around

the trimmer head and remove the grass once the

cutting attachment has stopped rotating.

■ Extended use of the tool at partial throttle will result in

lubricant dripping from the muffler.

head on the grass while running the engine at full throttle.

■ Run the engine at full throttle.

■ Tap the trimmer head on the ground to advance the line. With each tap, the line advances

further. A firm but gentle motion should be used when tapping the line on the ground (Fig. 20).

DO NOT keep the trimmer head pressed against the ground.

NOTICE: The cutting blade on the underside of the debris guard will cut the line to the correct

length.

NOTICE: Line that is too short may not advance using the tapping method and may need to be

done manually.

To advance the cutting line manually:

running faster than normal, or it appears as though the trimmer is less efficient, advance the line.

This will maintain proper performance and keep the line long enough to efficiently cut the grass.

cause product damage.

stop, and remove the battery pack. Failure to follow these instructions can result in serious personal

serious injuries.

dealer for assistance or Customer Service (Toll Free Number 866-384-8432).

NOTICE: Occasionally inspect the tool for damaged, missing, or loose parts such as screws, nuts,

bolts, caps, etc. Do not operate this tool if parts are damaged or missing. Secure all fasteners and

caps prior to using the tool. Please contact your service dealer for assistance or Customer Service

(Toll Free Number 866-384-8432).

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from

various types of commercial solvents and may be damaged by their use. Use clean, dry cloths to

remove dirt, dust, oil, grease, etc.

Keep all safety devices, air vents, and the motor housing free of dirt and dust.

TROUBLESHOOTING

TROUBLESHOOTING

6. Routine maintenance items such as lubricants, blade sharpening, etc.

7. Normal deterioration of the exterior finish due to use or exposure.

8. Parts that can wear out from normal use within the warranty period, such as the blades, collection

bags, spools, spool covers, etc.

Transportation Charges : Transportation charges for the movement of any power equipment unit or

attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay

transportation charges for any part submitted for replacement under this warranty unless such

return is requested in writing by LawnMaster

.

or internal parts should only be done by a qualified service professional. Please contact your

authorized service dealer or Customer Service at 866-384-8432.

1

2

2.1

2.2

2.2.1

2.2.2

2.2.3

7

8

9

9.1

9.2

9.3

9.4

10

10.1

10.2

16

321001101

321001102

321001103

321001104

321001105

321001106

321001107

321001114

321001115

321001116

321001117

321001118

321001119

321001120

321001121

321001122

321001112

321001128

Cleva 26cc 2-Cycle Engine

Throttle-body & Starter Set

Throttle-body Set

Starter Set

Electric Switch

Starter Switch Assembly

Stop Switch Set

7.2V Lithium-Ion Battery

Aluminum Trimmer Shaft

Assist Handle Assembly

Assist Handle

Handle Clasp

Ball Joint

Ball Socket

Gear Box

Bolt

Bolt

NPTGSS2617A MANUAL PARTS LIST

PARTS LIST 26CC 2-CYCLE ENGINE

Replacement parts highlighted in grey are available for after sales purchase. Replacement of repair

or internal parts should only be done by a qualified service professional. Please contact your

authorized service dealer or Customer Service at 866-384-8432.

26CC 2-CYCLE ENGINE PART LIST

Spark Plug Cover

Muffler

Insulation Sheet

Spark Plug

Crankcase Assembly

Ignition Coil Assembly

Stop Switch Cables

Pawl Assembly

Electric Starter Assembly

Carburetor Mount Assembly

Carburetor with one sheet

Fuel Tank Assembly

Rubber Pad

Fuel Tank Bracket

Lower Engine Cover

Crankshaft Piston Shank

Flywheel Cover Assembly

Flywheel Assembly

Bolt

Self-Tapping Screw

Self-Tapping Screw

321001132

321001136

321001137

321001138

321001139

321001147

321001148

321001149

321001150

321001151

321001164

321001165

321001166

3

4

5

6

7

8

9

10

11

12

13

14

18

19

20

21

22

28

29

30

35

36

37

NOTES

NOTES

CONTENIDOS

■ No bote el material del empaque hasta que haya inspeccionado completamente y utilizado

■ Si alguna pieza está dañada o faltante, llame al centro de servicio.

ARMADO

■ Suelte y extraiga el tornillo y arandela del protección contra sedimentos usando la llave

■ Inserte la pestaña de la abrazadera de montaje de la protección contra sedimentos hacia la

■ Alinee el orificio del tornillo de la abrazadera de montaje con el orificio del tornillo de la protec-

■ Asegure el tornillo con firmeza usando la llave hexagonal (Fig. 2).

3-4)

■ Alinee la batería con la ranura de la batería.

■ Inserte la batería en la ranura de la batería hasta que quede fija en posición. Asegúrese de que

■ No utilice fuerza al insertar la batería. Debiese calzar en su posición y hacer "clic".

■ Busque el botón de liberación de la batería, presiónelo y sosténgalo hacia arriba (Fig. 4).

ARMADO

5-6)

■ Suelte el cerrojo de leva de la manilla de apoyo.

■ Ajuste la manilla de apoyo usando la bola antivibración en la posición que le resulte más

■ Fije el cerrojo de leva de la manilla de apoyo. Tenga cuidado de no colocar la manilla de apoyo

■ La manilla de apoyo solo puede moverse en la dirección indicada por las dos flechas en la Fig.

■ Use únicamente con el cargador de baterías de 8,4 V LawnMaster

■ ¡Revise el voltaje! Los cargadores de baterías operan en CA de 100-240 V.

■ Cargue la batería a una temperatura entre 4 °C (40 °F) y 38 °C (100 °F) para garantizar una

BATERÍA Y CARGADOR

■ Quite el conector de carga del puerto de carga de la batería (Fig. 8).

■ Limpie el área alrededor del tanque de combusti-

■ Suelte el tapón del tanque de combustible

■ Comience siempre llegando un contenedor de

■ Asegúrese de que el combustible se mezcle

11-16)

■ Asegúrese de que la batería esté bien asegurada.

■ Coloque la bordeadora sobre una superficie nivelada

■ Presione el pulsador de cebado 5 veces.

■ El lugar de venta de la bordeadora debiera tener en venta hilo de repuesto.

■ Quite el carrete vacío de la bordeadora como se indica en la sección Cambio del carrete.

■ Extraiga cualquier hilo de corte remanente del carrete.

■ Reinstale el carrete vacío en el cabezal de la bordeadora como se indica en la sección Cambio

■ Presione y gire el cabezal de la bordeadora hacia la derecha para alinear la flecha del cabezal

■ Asegúrese de que el nuevo hilo de corte sea lo suficientemente largo, de aproximadamente 6

■ Corte el hilo en la mitad, dejando un poco fuera.

MANTENIMIENTO

■ Revise que no haya desgaste en la tapa del cabezal de la bordeadora, carrete y carcasa del

■ Para instalar un nuevo cabezal, sostenga la llave hexagonal para bloquear el eje. Luego, gire el

■ Quite la llave hexagonal del orificio.

MANTENIMIENTO

■ Gire la perilla del filtro de aire hacia la izquierda y saque con suavidad la tapa del filtro de aire

■ Quite el filtro de aire de la tapa del filtro de aire (Fig. 30).

MANTENIMIENTO

■ Limpie el filtro de espuma con agua jabonosa y enjuague. Seque el filtro al aire.

■ Coloque el filtro en su lugar, asegurándose de asentarlo correctamente sobre la tapa del filtro

MANTENIMIENTO

■ Ajuste la brecha de la bujía doblando el electrodo exterior (Fig. 35).

■ Reinstale la bujía limpiada o una nueva, girándola hacia la derecha (Fig. 36).

■ Reinstale el tapón de la protección contra chispas.

■ Reinstale la tapa de la bujía y fíjela usando la llave hexagonal.

■ Limpie todos los sedimentos de la caja de velocidades.

RESOLUCIÓN DE PROBLEMAS

NOTAS