Hitachi P42T501, P42T501A, P50T501, P5 Manual de usuario

Marca: Hitachi

Modelo: P42T501, P42T501A, P50T501, P5

Categoría: Televisores de plasma

Tipo: Manual de usuario

Este manual también es adecuado para

As an Energy Star

Partner,

Hitachi, Ltd. has determined

that this product meets the

Energy Star

guidelines for

energy efficiency.

test-bleed 3/3/06 10:18 AM Page 1

PLASMATELEVISION

Operating Guide for P42T501, P50T501

and P55T551

IMPORTANT SAFETY INSTRUCTIONS.......................................................................................2-3

FIRST TIME USE ......................................................................................................................... 4-22

THE REMOTE CONTROL....................................................................................................... 23-38

ON-SCREEN DISPLAY ............................................................................................................ 39-61

USEFUL INFORMATION.......................................................................................................... 62-71

END USER LICENSE AGREEMENT FOR HITACHI DTV SOFTWARE.............................. 144-152

APPENDIXES.........................................................................................................................153-154

INDEX............................................................................................................................................155

OPERATING GUIDE IN SPANISH .........................................................................................73-143

Change 1

Page 30, Added note

about PIP message

Spanish version - click here

test-bleed 3/3/06 10:18 AM Page 2

Important Safety Instructions

SAFETY POINTS YOU SHOULD KNOW ABOUT

YOUR HITACHI PLASMA TELEVISION

Our reputation has been built on the quality,

performance, and ease of service of HITACHI plasma

televisions.

Safety is also foremost in our minds in the design of

these units. To help you operate these products

properly, this section illustrates safety tips which will be

of benefit to you. Please read it carefully and apply the

knowledge you obtain from it to the proper operation of

your HITACHI plasma television.

Please fill out your warranty card and mail it to

HITACHI. This will enable HITACHI to notify you

promptly in the improbable event that a safety problem

should be discovered in your product model.

Follow all warnings and instructions marked on

this plasma television.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended

to alert the user to the presence of

uninsulated “dangerous voltage” within the

product’s enclosure that may be of a sufficient

magnitude to constitute a risk of electric shock to a

person.

The exclamation point within an equilateral

triangle, is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

READ BEFORE OPERATING EQUIPMENT

Follow all warnings and instructions marked on this

plasma television.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11. Only use the attachments/accessories specified by

the manufacturer.

12. Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

15.Televisions are designed to comply with the

recommended safety standards for tilt and stability.

Do not apply excessive pulling force to the front, or

top, of the cabinet which could cause the product

to overturn resulting in product damage and/or

personal injury.

16.Follow instructions for wall, shelf or ceiling

mounting as recommended by the manufacturer.

17. An outdoor antenna should not be located in the

vicinity of overhead power lines or other electrical

circuits.

18. If an outside antenna is connected to the receiver

be sure the antenna system is grounded so as to

provide some protection against voltage surges and

built up static charges. Section 810 of the National

Electric Code, ANSI/NFPA No. 70-1984, provides

information with respect to proper grounding for the

mast and supporting structure, grounding of the

lead-in wire to an antenna discharge unit, size of

grounding connectors, location of antenna discharge

unit, connection to grounding electrodes and

requirements for the grounding electrode.

Note to the CATV system installer: This reminder is

provided to call the CATV system installer’s attention to

Article 820-44 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding

system of the building, as close to the point of cable

entry as practical.

NEC National Electric Code

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

test-bleed 3/3/06 10:18 AM Page 3

Important Safety Instructions

Power source

This plasma television is designed to operate on 120

volts 60 Hz, AC current. Insert the power cord into a

120 volt 60 Hz outlet. The power cord is used as the

To prevent electric shock, do not use the plasma

television’s (polarized) plug with an extension cord,

receptacle, or other outlet unless the blades and

ground terminal can be fully inserted to prevent blade

exposure.

Never connect the plasma television to 50 Hz, direct

current, or anything other than the specified voltage.

Caution

Never remove the back cover of the

plasma television as this can expose you

to very high voltages and other hazards. If

the television does not operate properly,

unplug the plasma television and call your authorized

dealer or service center.

Caution

Adjust only those controls that are covered in the

instructions, as improper changes or modifications not

expressly approved by HITACHI could void the user’s

warranty.

Warning

• To reduce the risk of fire or electric shock, do not

expose this apparatus to rain or moisture.

• The plasma television should not be exposed to

dripping or splashing and objects filled with liquids,

such as vases, should not be placed on the

television.

authorized by Macrovision. Reverse engineering or

disassembly is prohibited.

Note

This digital television is capable of receiving analog

basic, digital basic cable television programming by

direct connection to a cable system providing such

programming. Certain advanced and interactive digital

cable services such as video-on-demand, a cable

operator’s enhanced program guide and data-enhanced

television services may require the use of a

set-top box.

For more information call your local cable company.

Note

• There are no user serviceable parts inside the

plasma television.

• Model and serial numbers are indicated on back side

and right side of the plasma television.

Prevention of screen damages

Continuous on-screen displays such as video games,

stock market quotations, computer generated graphics,

and other fixed (non-moving) patterns can be

permanently imprinted onto your TV screen. Such

“SCREEN DAMAGES” constitute misuse and are NOT

COVERED by your HITACHI Factory Warranty.

Lead Notice

This product contains lead. Dispose of this product in

accordance with applicable environmental laws. For

product recycling and disposal information, contact your

local government agency or www.eRecycle.org

(in California), the Electronic Industries Alliance at

www.eiae.org (in the US) or the Electronic Product

Stewardship Canada at www.epsc.ca (in Canada).

FOR MORE INFORMATION, CALL 1-800-HITACHI.

Public viewing of copyrighted material

Public viewing of programs broadcast by TV stations

and cable companies, as well as programs from other

sources, may require prior authorization from the

broadcaster or owner of the video program material.

This product incorporates copyright protection

technology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright

protection technology must be authorized by

Macrovision Corporation, and is intended for home and

other limited consumer uses only unless otherwise

disconnect device and shall remain readily operable.

• This apparatus shall be connected to a mains

socket outlet with a protective earthing connection.

If still images are left on the screen for more than 2.5

minutes, protection function will work automatically so that

contrast reduces to minimize image retention on plasma

display panel.

Please note that this is not a malfunction but it helps to

minimize image retention.

The original contrast will restore after moving images are

displayed for about 6 minutes. Original contrast can be

restored quickly by turning power On/Off with remote

control or power switch on unit.

Accessories

test-bleed 3/3/06 10:18 AM Page 4

First time use

Check to make sure you have the following accessories before disposing of the packing material.

Power Cord

Remote Control

1.5V batteries

Table Top Stand

(50" included)

For U.S. models:

For optional accessories, please access our web site at:

www.hitachi.us/tv

Table Top Stand

(42” included)

Two “AA” size,

Note: Please visit our

website for optional

accessories.

CAUTION: 1. Ceiling mounting is not recommended. Mounting the panel on the ceiling does not

provide adequate ventilation for the electronics or proper support for the front glass

panel. This plasma television product is designed for a maximum tilting angle of 45

degrees from vertical.

2. This stand for use only with Hitachi P42T501 and P50T501. Use with other

apparatus is capable of resulting in instability causing possible injury.

쐃 Remote Control Unit CLU-4371A

(Part No. HL02401).

쐇 Two "AA" size, 1.5V batteries.

쐋 Table Top Stand (UX27662 42" model)

쐏 Power Cord (P# EV01841).

쐃

쐋

쐇쐏

Open the battery cover of the remote control by pushing down and sliding the back cover off.

Insert two new “AA” size batteries for the remote contr

ol. When r

eplacing old batteries, push them towards the

springs and lift them out.

3. Match the batteries to the (+) and (-) marks in the battery

compartment.

Insert the bottom of the battery

, the (-) side, into the battery

compartment first, push towards the springs and insert the

top of the battery

, the (+) side, into place. Do not for

ce the

battery into the battery compartment.

5. Replace the cover.

Bottom View (Remote Control)

Lift up on tab to r

emove back cover.

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

CAUTION: Do not insert batteries with ‘+’ and ‘-’ polarities reversed as this may cause the batteries

to swell or rupture resulting in leakage.

(UX27282 50" model).

쐋

3. The wall mount unit for the 50" and 42" models is WM07S and for the

55" models is WM07L. Please see page 7 & 8 for important information related

to the wall mount. Wall Mout unit is an optional accessory (Not Included).

4 in.

10 cm

4 in.

10 cm

42"

50"

4 in.

10 cm

55"

test-bleed 3/3/06 10:18 AM Page 5

Securing to a table-top

1. Using wood screws (two) fasten the set to the

clamping screw holes on the rear of the Plasma

TV stand as shown below.

2. Using commercially available wood screws, secure

the set firmly in position.

Securing to a Wall

1. Keep the Plasma television 4 inches away from the

wall except when mounted using the wall mount

bracket.

2. Secure the television to the wall as shown.

NOTES: 1. Do not block the ventilation holes of the

Plasma Television. Blocking the ventilation

holes might cause fire or defect.

2. In case of an abnormal symptom, unplug

the AC cord.

3. If you purchased the wall mount bracket

option, please ask for professional installer.

Do not install by yourself.

4. Install the unit at a proper area where it does

not expose anyone to any danger of hitting

themselves (for example their hands, head

or face, etc.) against the edge of the unit and

cause personal injury.

Caution when moving the main unit

As this product is heavy, whenever it is moved, two

people arerequired to transport it safely. Whenever the

unit is moved it should be lifted forward using the top

and base on both sides of the Television for stability.

When moving the Television, lift the handles , then

support the top frame as shown below.

NOTE: TheTableTop Stand for model P55T501 is not

included (Optional).

To take measures to prevent the Plasma Television from tipping over and prevent possible injury

it is important to mount the unit in a stable and flat surface.

How To Set Up Your New Hitachi Plasma Television

* Please adjust the wire length to avoid

touching the wall when turning the TV.

Wood screw

two places

Wire

42” 50”

30 cm (12 inches)

10 cm (4 inches)

55”

ANTENNA

Unless your Plasma Television is connected to a cable

TV system or to a centralized antenna system, a good

outdoor color TV antenna is recommended for best

performance. However, if you are located in an

exceptionally good signal area that is free from

interference and multiple image ghosts, an indoor

antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor

illumination will not fall directly on the picture screen.

Also, be sure that the location selected allows a free

flow of air to and from the perforated back cover of the

set. In order to prevent an internal temperature

increase, maintain a space of 10 cm (4 inches) from the

sides/back of the Television, and 30 cm (12 inches)

from the top of the television to the wall. To avoid

cabinet warping, cabinet color changes, and increased

chance of set failure, do not place the TV where

temperatures can become excessively hot, for

example, in direct sunlight or near a heating appliance,

etc.

TURNINGANGLE

The maximum turning angle is 30° (left and right). Do

not place any objects on the path of the monitor when

using the swivel feature.

10.59 in. 13.93 in.

27 cm 36 cm

15 in. 16. 85 in.

38. 1 cm 42.8 cm

42"

50"

15 in. 16. 85 in.

38. 1 cm 42.8 cm

55"

First time use

test-bleed 3/3/06 10:19 AM Page 88

쐃

쐇

쐋

쐃

쐇

Pass the AC cord through Clamp #1 and connect

The AC cord and the signal cables can all be

held together with Clamp #2.

Depend on the model size 42",50" or 55", the

clamp may be different shapes. Only for 50" models

AC CORD

Clamp #2: Use this clamp to hold the AC cord and

the signal cables. For 50 " model please

Clamp #1 : Pass the AC cord through this clamp ;

then pull the clamp to tighten the AC

cord to the TV.

AC CORD INSTALLATION INSTRUCTION

The AC cord provided with your new Plasma Television needs to be installed correctly

to avoid the AC cord from disconnecting when rotating the TV on its Table top stand.

Located on the back of the TV are 2 plastic clamps to hold the AC cord. Please follow the

How to set up your new HITACHI Plasma Television

it to the TV. Pull on the clamp to tighten the

AC cord to the TV.

instructions below.

First time use

the clamp #2 will be included on the accessories

bag.

assemble this Clamp on the middle hole

of the base metal.

test-bleed 3/3/06 10:19 AM Page 88

SETTING FOR WALL MOUNTING ON 50" & 55" MODELS

STEP (1) :

Please locate the STAND METAL on the back of the TV . This metal is use to hold the TV and the Base ; so it needs

to remove 4 screws from the STAND base in order to separate the TV from the Base.

STAND METAL

STEP (2):

Please remove the 4 screws of the STAND metal from the TV, now the TV STAND can be separated from the TV.

For dimensions of the WALL MOUNT assembly please refer to page 68 & 69

STAND METAL

4 SCREWS

TV STAND BASE

NOTE: Use the specified WALL MOUNT unit for the Plasma TV depending on the size of your TV.

Please access our web site at: www.hitachi.us/tv for recommended accessories for your tv.

CAUTION- This Plasma Display Panel for use only with Hitachi WM07S Wall Mount. Use with other

Wall Mount is capable of resulting in instability causing possible injury.

CAUTION- This Plasma Display Panel for use only with Hitachi WM07L Wall Mount. Use with other

Wall Mount is capable of resulting in instability causing possible injury.

For Model P50T501

For Model P55T501

How to set up your new HITACHI Plasma Television

First time use

test-bleed 3/3/06 10:18 AM Page 6

How to set up your new HITACHI Plasma Television

SETTING FOR WALL MOUNTING ON 42" MODELS

STEP (1) :

Please locate the STAND METAL on the back of the TV . This metal is use to hold the TV and the Base ; so it needs

to remove 6 screws from the STAND base in order to separate the TV from the Base.

STAND METAL

STEP (2):

Please remove the 2 screws of the STAND metal from the TV, then remove 4 screws that hold the TV STAND BASE;

now the TV STAND can be separated from the TV.For dimensions of the WALL MOUNT assembly please refer to page 67.

STAND METAL

2 SCREWS

TV STAND BASE

Remove these 4 screws

to separate the TV from

the stand base.

NOTE: Use the specified WALL MOUNT base for the Plasma TV depending on the size of your TV.

Please access our web site at: www.hitachi.us/tv for recommended accessories for your tv.

Remove these 2 screws

first to separate the TV

rom the stand metal.

Then put these 2 screws

back to the TV.

CAUTION- This Plasma Display Panel for use only with Hitachi WM07S Wall Mount. Use with other

Wall Mount is capable of resulting in instability causing possible injury.

For Model P42T501

test-bleed 3/3/06 10:18 AM Page 7

How to set up your new HITACHI Plasma Television

VIEWING

The best picture is seen by sitting directly in front of

the TV and about 10 to 18 feet from the screen.

During daylight hours, reflections from outside light

may appear on the screen. If so, drapes or screens

can be used to reduce the reflection or the TV can

be located in a different section of the room.

If the TV’s audio output will be connected to a Hi-Fi

system’s external speakers, the best audio

performance will be obtained by placing the

speakers equidistant from each side of the receiver

cabinet and as close as possible to the height of

the picture screen center. For best stereo

separation, place the external speakers at least

four feet from the side of the TV, place the surround

speakers to the side or behind the viewing area.

Differences in room sizes and acoustical

environments will require some experimentation

with speaker placement for best performance.

ANTENNA CONNECTIONS TO REAR JACK

PANEL

VHF (75-Ohm) antenna/CATV (Cable TV)

When using a 75-Ohm coaxial cable system, connect CATV coaxial cable to the AIR/CABLE (75-Ohm) terminal.

Or if you have an antenna, connect the coaxial cable to the same AIR/CABLE terminal.

VHF (300-Ohm) antenna/UHF antenna

When using a 300-Ohm twin lead from an outdoor

antenna, connect the VHF or UHF antenna leads to

screws of the VHF or UHF adapter. Plug the adapter

into the antenna terminal on the TV.

When both VHF and UHF antennas are

connected

Attach an optional antenna cable mixer to the TV

antenna terminal, and connect the cables to the

antenna mixer. Consult your dealer or service store for

the antenna mixer.

4" Minimum

BEST

HORIZONTAL

VIEWING ANGLE

10'

15' 20'

To CATV cable

To outdoor antenna

To outdoor VHF

or UHF antenna

To outdoor antenna

or CATV system

To UHF

antenna

Antenna Mixer

AIR / CABLE

NOTE: Connecting a 300-Ohm twin lead connector may cause interference. Using a 75-Ohm coaxial

cable is recommended.

First time use

test-bleed 3/3/06 10:18 AM

300-Ohm Twin Lead

This outdoor antenna cable must be connected to an

antenna adapter (300-Ohm to 75-Ohm).

Phono or RCA

Used on all standard video and audio cables which

connect to inputs and outputs located on the

television’s rear jack panel and front control panel.

“F” Type 75-Ohm Coaxial Antenna

For connecting RF signals (antenna or cable TV) to the

antenna jack on the television.

S-Video (Super Video)

This connector is used on camcorders, VCRs and laser-

disc players with an S-Video feature in place of the

standard video cable to produce a high quality picture.

Optical Cable

This cable is used to connect to an audio amplifier with

an Optical Audio In jack. Use this cable for the best

sound quality.

HDMI Cable

This cable is used to connect your external devices

such as Set-Top-Boxes or DVD players equipped with

an HDMI output connection to the TV’s HDMI input.

Stereo Cable (3.8mm plug to 3.5mm plug)

Used on all standard video and audio cable which

connect to inputs and outputs located on the rear jack

panel and front control panel.

Hook-up Cables and Connectors

Most video/audio connections between components can be made with shielded video and audio cables that have

phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be

purchased from most stores that sell audio/video products. Below are illustrations and names of common

connectors. Before purchasing any cables, be sure of the output and input connector types required by the

various components and the length of each cable.

AUDIO OUT

3.8mm

STEREO

MINI-PLUG

RCA TYPE

PLUGS

Cable

test-bleed 3/3/06 10:18 AM

Quick Reference Remote Control Buttons and Functions

In addition to controlling all of the functions on your HITACHI Plasma TV, the new remote control is designed to

operate different types of devices, such as, DVD Players, CBL (Cable Boxes), set-top-boxes, satellite receivers,

and VCRs. The remote control must be programmed to control the chosen device. Please see pages 23-38 for a

complete description of all features and programming of the Remote Control.

NOTES: 1. The TV’s remote control sensor is located on the right bottom portion of the TV screen. To

control TV functions, please point the remote control directly at the remote control sensor for

best results.

2. VCR precode is included in the PVR mode.

LEGEND

TV – Television PVR – Video Recorder/Player

CBL – Cable Box DVD – Digital Video Disc Player

SAT – Satellite

POWER BUTTON

(TV, DVD, SAT/CBL,PVR/VCR)

Turns the selected device on and o.

SOURCE SELECT BUTTON

(TV, DVD, PVR/VCR, SAT/CBL)

Changes the mode of the Universal Remote

Control to control the device selected.

DVD/VCR CONTROL BUTTONS

(DVD, PVR/VCR)

Controls the functions of your VCR,

DVD and audio devices.

DAY/NIGHT BUTTON

(TV)

Toggles picture mode settings

between DAY and NIGHT mode.

ASPECT BUTTON

(TV)

Changes the aspect ratio of the TV.

PIP CONTROL BUTTON

(TV)

Press to show and change the Picture-in-Picture mode.

MENU BUTTON

(TV,DVD,SAT/CBL,PVR/VCR)

Accesses the OSD menu system.

(-) BUTTON

(TV,STB)

The (-) button is used when the remote is in

Set-Top-Box (STB) mode or when the TV uses a

digital input.

NUMERIC BUTTONS

(TV, DVD, SAT/CBL, PVR/VCR)

Used to manually enter the TV channel, and used

for numeric entry when navigating through the

the OSD, INPUTS.

GUIDE BUTTON

(SAT/CBL, PVR)

Accesses the program guide of other devices.

EXIT BUTTON

(TV, SAT/CBL, PVR/VCR)

Exits out of the OSD, INPUTS menu

systems if their menu is displayed.

LAST CHANNEL BUTTON

(TV, SAT/CBL, PVR)

Switches between the current and last channel viewed.

ENTER BUTTON

Press to use as SELECT feature.

Can only be used on TV mode.

INFO BUTTON

(TV, STB, CBL, PVR)

Displays various information on the

screen, such as channel information.

CHANNEL UP & DOWN BUTTONS

(TV, CBL, STB, PVR/VCR)

Changes up or down the channel.

CURSOR PAD/SELECT BUTTON

(TV, DVD, SAT/CBL,PVR/VCR)

The Cursor Pad is used as a cursor to navigate

through the OSD and INPUT menu systems.

The Select button is used to Select/Activate

highlighted menu items.

VOLUME BUTTONS

(TV)

Increase up and decrease down to adjust

the audio level of your TV.

PAUSE BUTTON

(TV,PVR/VCR, DVD)

Press to show and change the Freeze mode of the TV.

Also used to pause other devices when the remote is in

DVD, PVR/VCR.

INPUTS BUTTON

(TV)

Accesses the INPUTS menu system.

MODE INDICATOR

Turns on or blinks to show remote control

mode when the SOURCE ACCESS buttons

are pressed.

Closed Caption (CC) BUTTON

(TV)

MUTE BUTTON (TV)

Reduces the audio level to 50% if pressed

once, and to complete mute if pressed

twice. Press it a third time to restore audio

level.

FAVORITE CHANNEL

(FAV CH) button (TV)

Press to enter/access Favorite Channel (FAV CH) mode.

(Favorite channel is only available for TV mode.)

Press to show and change the

Closed Caption mode.

First time use

VCR – Videocassete Recorder

test-bleed 3/3/06 10:18 AM Page 10

First time use

PUSH TO OPEN CONTROL DOOR

FRONT VIEW

PUSH EJECT

PHOTO INPUT

햲

햺

햹

햸

햴

햳

햶

햷

햲 FRONT POWER button

Press this button to turn the Plasma Television

ON/OFF. It can also be turned ON/OFF by remote

control. The “MAIN POWER” button must be at

stand-by mode.

햳 MENU/SELECT button

This button allows you to enter the MENU, making

it possible to set TV features to your preference

without using the remote. This button also serves

as the SELECT button when in MENU mode.

햴

HDMI-FRONT

Use the front HDMI input for extrenal devices such

as Set-Top-Boxes or DVD players equipped with an

HDMI output connection (see page 15 for reference).

햵 INPUT/EXIT button

Press this button to access the INPUT menu.

Press again to exit the MENU mode.

햶 CHANNEL selector

Press these buttons until the desired channel

appears in the top right corner of the TV screen.

These buttons also serve as the cursor down ()

and up () buttons when in MENU mode.

햷 VOLUME level

Press these buttons to adjust the sound level. The

volume level will be displayed on the TV screen.

These buttons also serve as the cursor left () and

right () buttons when in MENU mode.

햸 POWER button

Television MAIN POWER button

This power button is for the complete system, and

must be turned ON/OFF manually. It is

recommended to leave the “MAIN POWER” to ON

condition (lights red) for stand-by mode.

NOTE: When the “MAIN POWER” button is set to

OFF or the TV is unplugged, the clock will

stop and may eventually reset itself.

햽

Front Panel Controls

햵

FRONT PANEL CONTROLS

Upgrade Card / SD CARD PHOTO INPUT

This card slot is for future software upgrades.

Hitachi will notify you if a software upgrade is

required for your TV. In order to receive written

notification, please complete and return your

warranty card. To view digital still pictures please

햻

햹

insert a SD card into the card slot with

pictures taken on a Digital Camera, to view

them on the TV screen.

The Main Power

button is located

on the broadside

bottom, under the

mark " ".

test-bleed 3/3/06 10:18 AM

REMOTE CONTROL sensor

Point your remote at this area when selecting

channels, adjusting volume, etc.

햺

햻

INPUT-FRONT JACKS

INPUT-FRONT provide composite Video jacks for

connecting equipment with this capability,

such as a DVD player or Camcorders.

Front Panel Controls

POWER light indicator

To turn the TV ON, press the main power

switch located on the lower right side of the

TV. A red stand-by indicator lamp located on

the lower right corner of the front bezel will

illuminate. The Plasma TV is now ready for

remote ON/OFF operation.

NOTES: 1. Your HITACHI Plasma TV will appear to be turned OFF (lights orange) if there is no video input

when INPUT : 1, 2, 3, Front or HDMI : 1, 2, Front is selected. Check the Power Light to

make sure the TV is turned off or in Stand-by mode (lights red) when not in use.

2. Remote Control can not turn ON/OFF the “MAIN POWER” of the TV.

햽

Indicating Lamp

R/C sensor

햺

햻

Indicating Lamp Power Status Operating

OFF. When the main power switch is set to Off.

When the main power switch on the TV is ON.

(Stand-by)

TV MAIN POWER is ON with no signal input

(Power Saving)

except antenna (no sync. signal).

Off

Lights

Red

OFF.

Lights

Blue

TV MAIN POWER is ON ; picture is shown.

Lights

Orange

Off

Blinking

Blue 3 times

When TV receive the IR signal once from R/C.

First time use

test-bleed 3/3/06 10:18 AM Page 12

햲 Antenna Input

To switch between Cable and Air input, go to the

Channel Manager option to change the signal

source CABLE or AIR.

햳 Audio/Video Inputs 1, 2 and 3

By using the INPUTS button, the CURSOR PAD (

and ), and the SELECT button or CURSOR PAD

 of the remote control, you can select each video

source. Use the audio and video inputs to connect

external devices, such as VCRs, camcorders,

laserdisc players, DVD players etc. (if you have

mono sound, insert the audio cable into the left

audio jack).

햴 MONITOR OUT & AUDIO OUT

These jacks provide fixed audio and video

signals (CABLE/AIR or INPUTS ) which are

used for recording. Use the S-VIDEO output

for high quality video output. Component signal

to Input 2 and 3, and HDMI inputs will not

have monitor output.

햵 Optical Out (Digital Audio)

This jack provides Digital Audio Output for your

audio device that is Dolby

® Digital and PCM

compatible, such as an audio amplifier.

NOTE: *Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D

symbol are trademarks of Dolby

Laboratories.

햶 S-VIDEO Input 1

The Input 1 provide S-VIDEO (Super Video)

jacks for connecting equipment with S-VIDEO

output capability.

NOTE: 1. You may use VIDEO or S-VIDEO inputs to

connect to INPUT 1, but only one of these

inputs may be used at a time.

2. S-VIDEO output may be used for

recording, only when the input is of

S-VIDEO type.

햷 HDMI 1, 2 (High Definition Multimedia

Interface)

ABOUT HDMI – HDMI is the

next-generation all digital interface for consumer

electronics. HDMI enables the secure distribution

of uncompressed high-definition video and multi-

channel audio in a single cable. Because digital

television (DTV) signals remain in digital format,

HDMI assures that pristine high-definition images

retain the highest video quality from the source all

the way to your television screen.

Use the HDMI input for your external devices such

as Set-Top-Boxes or DVD players equipped with an

HDMI output connection.

HDMI, the HDMI logo and High-Definition

Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.

NOTE: 1. The HDMI input is not intended for use

with personal computers.

2. Only DTV formats such as 1080p,1080i, 720p,

480i and 480p are available for HDMI input.

햸 Component: Y-PBPR Inputs

INPUTS 2 and 3 provide Y-P

BPR jacks for

connecting equipment with this capability, such as

a DVD player or Set Top Box. You may use

composite video signal for both inputs.

NOTE: 1. Do not connect composite VIDEO and

S-VIDEO to INPUT 1 at the same time.

S-VIDEO has priority over VIDEO input.

2. Your component outputs may be labeled

Y, B-Y, and R-Y. In this case, connect the

components B-Y output to the TV’s P

input and the components R-Y output to

the TV’s P

R input.

3. Your component outputs may be labeled

Y-C

BCR. In this case, connect the component

B output to the TV’s PB input and the

component C

R output to the TV’s PR input.

4. It may be necessary to adjust TINT to

obtain optimum picture quality when using

the Y-P

BPR inputs (see page 41).

5. To ensure no copyright infringement, the

MONITOR OUT output will be abnormal,

when using the Y-PBPR jacks and HDMI

Input.

6. INPUT 2 , and 3 (Y/VIDEO) can be used for

composite video and component video

input.

햹 For Special AV control use only.

햺 For Factory use only.

햲

햳

햸

햹

햴

햷

햺

햵

햶

Rear Panel Connections

test-bleed 3/3/06 10:18 AM Page 13

The FRONT panel jacks are provided as a convenience to allow you to easily connect HDMI or DVI signals

from a DVD, Set Top Box , Video Game as shown in the following examples (When connecting DVI signal it will

OUTPUT

L R

DIGITAL OUTPUT

DVI to HDMI

Cab l e

Back of

HDTV Set-Top-Box or

DVD Player

HDMI DIGITAL

OUTPUT CAPABILITY

DVD , Set Top Box,

Video Game Console.

FRONT INPUT PANEL

DVI DIGITAL

OUTPUT CAPABILITY

DVD , Set Top Box,

Video Game Console.

need to connect the audio output into the Front Audio Input jacks) :

A) Connecting HDMI signal.

B) Connecting DVI signal.

FRONT INPUT PANEL

PUSH EJECT

PHOTO INPUT

PUSH EJECT

PHOTO INPUT

specifications.

Note : Special device cables will be

according to the own device

Connecting External Video Sources

NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back

picture may be abnormal.

specifications.

Note : Special device cables will be

according to the own device

First time use

test-bleed 3/3/06 10:18 AM Page 14

The FRONT panel jacks are provided as a convenience to allow you to easily connect a camcorder , DVD, Video

Game and a VCR as shown in the following examples:

NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the

played back picture may be abnormal.

Connecting External Video Sources

FRONT INPUT PANEL

L/Mono input jack .

Note : For Monoaural devices, please

connect Audio signal cable into

Video Game

Video Camera

COMPOSITE VIDEO

OUTPUT CAPABILITY

DVD , Video Game

Console.

PUSH EJECT

PHOTO INPUT

The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set

Top Box to your Plasma TV is dependent on the model and features of each component. Check the

owner’s manual of each component for the location of video and audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to

accommodate your particular assortment of components and features. For best performance, video and

audio cables should be made from coaxial shielded wire.

Before Operating External Video Source

Connect an external source to one of the INPUT terminals, then press the INPUTS button to show the

INPUTS menu. Use the CURSOR PAD ( and ) to select the Input of your choice. Then press

the SELECT button or the CURSOR PAD  to confirm your choice (see page 26).

HDMI-Front

Photo Input

Cable

Air /

Input 1

Move SEL Sel.

Input 2

OUTPUT

L R

Video

specifications.

Note : Special device cables will be

according to the own device

test-bleed 3/3/06 10:18 AM Page 15

NOTE: Cables are optional, except when specified.

HDMI DIGITAL

OUTPUT CAPABILITY

HDMI OUTPUT

HDMI

VCR #1

Cable TV coaxial cable

2-Way signal splitter

Outside Antenna

ANT

OUTPUT

S-VIDEO

VL R

DIGITAL

OUTPUT CAPABILITY

DIGITAL OUTPUT

OUTPUT

Y P

L R

HDTV Set-Top Box

DVD Player

DVI

HDMI

AUDIO OUT

OUTPUT

L R

VCR #2

V L R

INPUT

S-VIDEO

Optional

Rear Panel Connections

First time use

test-bleed 3/3/06 10:18 AM Page 16

Tips on Rear Panel Connections

• S-VIDEO, Y-PBPR, or HDMI connections are provided for high performance laserdisc players, VCRs etc. that

have this feature. Use these connections in place of the standard video connection if your device has this

feature.

• If your device has only one audio output (mono sound), connect it to the left audio jack on (L/(MONO)) the

Rear Panel.

• Refer to the operating guide of your other electronic equipment for additional information on connecting

your hook-up cables.

• A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line

output (INPUT: 1 in the example on page 17). Refer to your VCR operating guide for more information on

line input-output connections.

• Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.

• COMPONENT: Y-P

(Input 2 & 3) connections are provided for high performance components, such as

DVD players and set-top-boxes. Use these connections in place of the standard video connection if your

device has this feature.

• Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y

output to the TV’s P

input and the components R-Y output to the TV’s P

input.

• Your component outputs may be labeled Y-C

. In this case, connect the components C

output to the

TV’s P

input and the components C

output to the TV’s P

input.

• It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-P

inputs. (See

page 41)

• To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-P

BPR and

HDMI input jacks.

• Input HDMI 1, HDMI 2 or HDMI FRONT can accept HDMI signal.

• S-VIDEO monitor output may be used for recording only when the input is of S-VIDEO type.

• When using a HDMI input from a Set-Top-Box, it is recommended to use a 1080p, 1080i or 720p input signal.

INSTALLATION RECOMMENDATION:

1. Video signals fed through a VCR may be affected by copyright protection systems and the picture

will be distorted on the television.

2. Connecting the television directly to the Audio /Video output of a Set-Top-Box will assure a more

normal picture.

• When HDMI input a 1080p signal, the length of the cable should be less than 5 meters.

test-bleed 3/3/06 10:18 AM Page 17

Back of

VCR

OUTPUT

VCR

Video

CONNECTING A VIDEO AND STEREO AUDIO

SOURCE TO INPUT1 ~ FRONT INPUT

1. Connect the cable from the VIDEO OUT of the

VCR or the laserdisc player to the INPUT

(VIDEO) jack, as shown on the Rear Panel to the

right.

2. Connect the cable from the AUDIO OUT R of the

VCR or the laserdisc player to the INPUT

(AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the

VCR or the laserdisc player to the INPUT

(AUDIO/L) jack.

4. Press the INPUTS button, then select INPUT 1

2,3 or Front from the INPUTS menu to view the

program from the VCR or laserdisc player.

5. Select CABLE or AIR from the INPUTS menu to

return to the last channel tuned.

NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and

sound that is played back will be abnormal if the connection is loose.

2.A single VCR can be used for VCR #1 and VCR #2 (see page 17) but note that a VCR cannot record

its own video or line output. Refer to your VCR operating guide for more information on line input-

output connections.

3. When INPUT 2 or 3 are used, it is necessary to connect the video output of the device to the

Y/VIDEO input jack of the TV .

CONNECTING AN S-VIDEO AND STEREO AUDIO

SOURCE TO INPUT 1

1. Connect the cable from the S-VIDEO OUT of

the S-VHS VCR or the laserdisc player to the

INPUT (S-VIDEO) jack, as shown on the Rear

Panel to the right.

2. Connect the cable from the AUDIO OUT R of

the VCR or the laserdisc player to the INPUT

(AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of

the VCR or the laserdisc player to the INPUT

(AUDIO/L) jack.

4. Press the INPUTS button, then select INPUT 1

from the INPUTS menu to view the program

from the VCR or laserdisc player.

5. Select CABLE or AIR from the INPUTS menu to

return to the last channel tuned.

NOTE: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and

sound that is played back will be abnormal if the connection is loose.

2.A single VCR can be used for VCR #1 and VCR #2 (see page 17), but note that a VCR cannot record

its own video or line output. Refer to your VCR operating guide for more information on line input-

output connections.

Connecting External Video Sources

VCR or Laserdisc Player

OUTPUT

Back of VCR or

Laserdisc Player

S-VIDEO

Video L R

Cable or

Air signal

Cable or

Air signal

First time use

test-bleed 3/3/06 10:18 AM Page 18

CONNECTING A COMPONENT SOURCE WITH HDMI OR

DVI CAPABILITY TO HDMI 1, HDMI 2 OR HDMI FRONT

1. Connect the HDMI or DVI to HDMI connection

cable from the output of the HDTV set top box

or DVD player to the HDMI input as shown

on the Rear panel below.

2. With DVI output, connect the cable from the

AUDIO OUT R of the HDTV set top box or DVD

player to the INPUT (AUDIO/R) jack as shown on

the Rear Panel below.

3. With DVI output, connect the cable from the

AUDIO OUT L of the HDTV set top box or DVD

player to the INPUT (AUDIO/L) jack as shown

on the Rear Panel below.

4. Press the INPUTS button, then select HDMI 1, 2

or FRONT to view the program from the HDTV

SET TOP BOX or DVD player.

5. Select CABLE or AIR from the INPUTS menu to

return to the last channel viewed.

NOTE: 1. Completely insert the connection cord

plugs when connecting to rear panel jacks.

The picture and sound that is played back

will be abnormal if the connection is loose.

2. The HDMI input on HDMI 1 , 2 and FRONT

contains the copy protection system called

High-bandwidth Digital Content Protection

(HDCP). HDCP is a cryptographic system

that encrypts video signals when using

HDMI connections to prevent illegal

copying of video contents.

3. HDMI is not a “NETWORK” technology. It

establishes a one-way point-to-point

connection for delivery of uncompressed

video to a display.

4. The connected digital output device

controls the HDMI interface so proper set-up

of device user settings determines final

video appearance.

5. When using a DVI to HDMI cable, connect the

Audio Out L and R cables at the same INPUT

(1 , 2 or Front) as your HDMI INPUT(1 , 2 or Front).

(For FRONT INPUT see page 15 for reference).

Connecting External Video Sources

HDTV Set-Top-Box or

DVD Player

DIGITAL OUTPUT

Back of

HDTV Set-Top-Box or

DVD Player

HDMI

Cable

OUTPUT

DIGITAL OUTPUT

DVI to HDMI

Cable

Back of HDTV

Set-Top-Box

or DVD Player

HDMI input

DVI to HDMI Input

CABLE

Air signal

HDTV Set-Top-Box or

DVD Player

CABLE

Air signal

First time use

test-bleed 3/3/06 10:18 AM Page 19

CONNECTING A COMPONENT AND STEREO

AUDIO SOURCE TO INPUT 2 or 3 :Y-PBPR.

1. Connect the cable from the Y OUT of the

Laserdisc/DVD player or HDTV set top box to

the INPUT (Y) jack, as shown on the Rear

panel below.

2. Connect the cable from the P

OUT or B-

Y OUT of the Laserdisc/DVD player or HDTV

set top box to the INPUT (P

jack.

3. Connect the cable from the P

OUT or R-

Y OUT of the Laserdisc/DVD player or HDTV

set top box to the INPUT (P

) jack.

4. Connect the cable from the AUDIO OUT R of

the Laserdisc/DVD player or HDTV set top box

to the INPUT (AUDIO/R) jack.

5. Connect the cable from the AUDIO OUT L of

the Laserdisc/DVD player or HDTV set top box

to the INPUT (AUDIO/L) jack.

6. Press the INPUTS button, then select INPUT 2

or 3 from the INPUTS menu to view the

program from the Laserdisc/DVD player or

HDTV set top box.

7. Select CABLE or AIR to return to the last

channel tuned.

NOTE: 1. Completely insert the connection cord

plugs when connecting to rear panel jacks.

The picture and sound that is played back

will be abnormal if the connection is loose.

2. See page 18 for tips on REAR PANEL

CONNECTIONS.

Connecting External Audio/Video Devices

OUTPUT

DVD Player

Back of

DVD Player

OUTPUT

L R Y P

B P

HDTV Set-Top Box

PR/CR PB/CB Y

VIDEO

AUDIO

CABLE

Air signal

test-bleed 3/3/06 10:18 AM Page 20

First time use

CONNECTING A VIDEO AND MONAURAL AUDIO

SOURCE TO INPUT 1 ~ FRONT INPUT

1. Connect the cable from the VIDEO OUT of the

VCR or the laserdisc player to the INPUT

(VIDEO) jack, as shown on the Rear Panel on the

right.

2. Connect the cable from the AUDIO OUT of the

VCR or the laserdisc player to the INPUT

(MONO)/L(AUDIO) jack.

3. Press the INPUTS button, then select INPUT 1

2,3 or Front from the INPUTS menu to view the

program from the VCR or the laserdisc player.

4. Select CABLE or AIR from the INPUTS menu to

return to the previous channel.

CONNECTING AN EXTERNAL AUDIO AMPLIFIER

To monitor the audio level of the Plasma TV to an

external audio amplifier, connect the system as

shown on the right. The “OPTICAL OUT” from the

Rear Panel is a fixed output. The Volume of the

amplifier is controlled by the amplifier, not by the

Plasma Television. The OPTICAL OUT terminal

outputs all audio sources with Optical IN capability.

1. Connect an optical cable from the Optical out to

the Optical input of a separate Stereo System

Amplifier as shown on the Rear Panel on the

right.

CONNECTING MONITOR OUT

The MONITOR OUT terminal outputs video and

audio of CABLE/AIR and INPUTS 1, 2, 3 and Front.

It does not output component and HDMI video.

1. Connecting S-Video:

Connect the cable from the S-VIDEO OUT of

the Rear Panel to the INPUT (S-VIDEO) jack, of

the VCR or Laserdisk player.

Connecting Video:

Connect the cable from the VIDEO INPUT of

the VCR or the laserdisc player to the VIDEO

out jack on the TV Rear Panel.

2. Connect the cable from the AUDIO IN R of the

VCR or the laserdisc player to the OUTPUT

(AUDIO/R) jack on the TV Rear Panel.

3. Connect the cable from the AUDIO IN L of the

VCR or the laserdisc player to the OUTPUT

(AUDIO/L) jack on the TV Rear Panel.

NOTE: When making video connections, connect S-Video only or Video only. If both are connected, S-Video

takes priority.

CABLE

Air signal

VCR or other external

components

INPUT

S-VIDEO

R L V

Optional

(For INPUT FRONT please see page 16 for reference).

Connecting External Audio/Video Devices

CABLE

Air signal

Stereo System Amplifier

OPTICAL

Stereo System Amplifier

or DVD Player

CABLE

Air signal

Back of

VCR

OUTPUT

VCR

VIDEO OUT

AUDIO OUT

test-bleed 3/3/06 10:18 AM Page 21

In addition to controlling all the functions on your

HITACHI Plasma TV, the new remote control is

designed to operate different types of VCRs, CATV

(Cable TV) converters, set-top-box, satellite

receiver, DVD players, and other audio/video

equipment with one touch. Basic operation keys

are grouped together in one area.

To operate your Plasma TV, select TV by

pressing the Source button of the Source Select

on the remote. The TV mode indicator will blink,

indicating that the remote will now control your

television.

To operate your VCR/PVR (Personal Video

Recorder), select PVR/VCR by pressing the Source

button of the Source Select on the remote. The

PVR/VCR mode indicator will blink, indicating that

the remote will now control your VCR/PVR (see

page 35 for instructions on how to program the

remote to control your VCR/PVR).

To operate your cable box, select SAT/CBL by

pressing the Source button of the Source Select

on the remote. The SAT/CBL mode indicator will

blink, indicating that the remote will now control

your cable box (see page 32 for instructions on

how to program the remote to control your cable

box).

To operate your set-top-box or satellite receiver

select SAT/CBL by pressing the Source button of

the Source Select on the remote. The SAT/CBL

mode indicator will blink, indicating that the remote

will now control your set-top-box or satellite receiver

(see page 33 for instructions on how to program the

remote to control your set-top-box or satellite

receiver).

To operate your DVD player, select DVD by

pressing the Source button of the Source Select

on the remote. The DVD mode indicator will blink,

indicating that the remote will now control your

DVD Player (see page 34 for instructions on how to

program the remote to control your DVD player).

The Remote Control

How to Use the Remote to Control Your TV

NOTE: For automatic DAY/NIGHT picture mode settings,

see page 55.

POWER button

Press this button to turn the TV set on or off when

the remote is in TV mode. (See page 23 for instructions

on how to set the remote control to TV mode).

MODE Indicator

Turns on or blinks three times to show remote control

SOURCE SELECT button

Press this button to select remote control mode.

PAUSE button

Press the PAUSE button to freeze the picture.

Press the EXIT button to return the picture to

motion. Press the PAUSE button repeatedly to

cycle through the three different freeze modes (see

page 31).

Freeze

쐃

쐇

쐋

쐏

쐄

쐂

쐆

쐊

쐎

쐅

씈

씌

쐃

쐏

쐇

쐋

DAY/NIGHT button

Press this button to toggle between Day (Normal),

Day (Dynamic) and Night picture mode settings. Select

DAY for day time viewing with more brightness and

contrast to compete with room light. Select NIGHT

for night time viewing with less brightness and

contrast for a more detailed picture (see page 41

for settings changes).

쐄

쐈

쐉

씉

씊

씋

mode.

The Remote Control

How to Use the Remote to Control Your TV

IMA G E INPUT

16:9 STANDARD 2

Use this aspect mode to display 16:9 sources like

HDTV and DVD’s preserving the original 16:9

aspect ratio showing 100% of the size.

ASPECT button

Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal format

received, the picture format ratio allows you to adjust the images through the following options.

• Antenna-Analog Channel

• S-Video/Video Input

(Auto Aspect: Off)

• HDMI-480i/480p Input

(Auto Aspect: Off)

• Component-480i/480p

Input (Auto Aspect: Off)

Note: Please see Appendix A

on page 153-154.

• Antenna-Digital Channel (4:3)

• S-Video/Video 4:3/Letter

Input (Auto Aspect: On)

• HDMI-480i/480p 4:3/

Letter Input (Auto Aspect: On)

• Component-480i/480p 4:3/

Letter Input

(Auto Aspect: On)

Note: Please see Appendix A

on page 153-154.

• S-Video/Video 16:9 Input

(Auto Aspect: On)

• HDMI-480i/480p 16:9 Input

(Auto Aspect: On)

• Component-480i/480p

16:9 Input

(Auto Aspect: On)

Note: Please see Appendix A

on page 153-154.

• Antenna-Digital Channel (16:9)

•HDMI-720p/1080i/1080p Input

• Component-720p/1080i

Input

Note: Please see Appendix A

on page 153-154.

NOTE: 1. The Aspect Stylein all video inputs have independent Aspect Style setting.

2. Vertical position adjustments are directly available when you choose 4:3 EXPANDED/ZOOM1/ZOOM2 or

16:9 ZOOM aspect style (see also page 43).

4:3 STANDARD

Use this aspect mode to display conventional (4:3)

images. Side panels (gray areas) are placed to the

left and right of the image to preserve the original

aspect ratio of the source. Note: Use this mode for

only 15% of your total viewing time to prevent

uneven aging of the phosphors. Phosphors in the

lighted area of the picture will age more rapidly

than the gray areas.

4:3 EXPANDED

Use this aspect mode to display conventional (4:3)

sources by linearly increasing image expansion

from the center towards the edges of the display

area in order to fill it.

4:3 ZOOM1/ZOOM2

Use these aspect modes to zoom in on conventional

(4:3) sources.

16:9 STANDARD 1

Use this aspect mode to display 16:9 sources like

HDTV and DVD’s preserving the original 16:9

aspect ratio showing 95% of the size.

16:9 ZOOM

Use this aspect to Zoom-in once while in 16:9 aspect.

3. When displaying 16:9 STANDARD 2 it may appear lines at the edge of the picture this is normal operation

of the TV.

쐂

The Remote Control

How to Use the Remote to Control Your TV

NOTE: 1. Press the INFO button again or the EXIT

button to return to normal viewing.

2.The Aspect setting will not be shown if

the channel is locked.

S-IN: 1

480i 3:17PM

Auto

DIGITAL CHANNELS

Digital Closed Caption

This icon will appear only when

receiving a Digital Broadcast with

Closed Captioning.

Show Name Air 8

3:00PM-

3:30PM KXYZ-HD

ST TV-G 480i 3:17PM

Auto STEREO

Program Run Time

Program Information

Broadcast

Rating

Picture Format

Audio

Broadcast

Main Picture Source

and channel indication

Broadcast channel

identication

Clock

Closed

Caption setting

Audio Source

Selection

ANALOG CHANNELS

Show Name Air 15-1

3:00PM-

3:30M KPBS-HD

ST 1080i 3:17PM

Auto

Program Run Time

Program Information

Broadcast

Rating

Picture Format

Audio

Broadcast

Main Picture Source

and channel indication

Broadcast channel

identication

Clock

Closed

Caption setting

DTvCC TV-G

REGION 5

Alternate

Rating

Program Description

(Press INFO again for a more detailed description)

When a Component Video: Y-PbPr

Input is connected to INPUT 3

Input Signal

Format

Y-PBPR: 3

480i 3:17PM

Auto

When an S-VIDEO Input is connected

to INPUT 1

MENU button

The MENU button will start the On-Screen Display.

EXIT button

This button will exit all On-Screen Displays.

쐆

쐎

쐊

INPUTS button

When the remote control is in TV mode, press this

button to access the INPUTS menu. Use the

CURSOR and SELECT buttons to scroll and select

the inputs that are being used. Pressing the

INPUTS button repeatedly will also cycle through

the Inputs menu items. Then press the SELECT

button to select.

INPUT 1 Select to choose INPUT 1.

INPUT 2 Select to choose INPUT 2.

INPUT 3 Select to choose INPUT 3.

INPUT- FRONT Select to choose FRONT INPUT .

HDMI 1 Select to choose HDMI 1 INPUT.

HDMI 2 Select to choose HDMI 2 INPUT.

HDMI-Front

Photo Input

Input 2

Air / Cable

Move SEL Select

Input 1

HDMI- FRONT Select to choose FRONT HDMI INPUT.

AIR/CABLE Select between Air or Cable signal.

CURSOR buttons/SELECT button

All the On-Screen Display features can be set or

adjusted by using the CURSOR buttons and the

SELECT button, except for numeric entries. Press

the CURSOR buttons toward desired direction and

press the SELECT button to select.

쐅

쐈

쐉

PICTURE-IN-PICTURE button

See separate section on pages 30-31 for a more

detail description.

CLOSED CAPTIONS (CC) button

Use this button to display the dialogue, narration,

and/or sound effects of a television program or home

GUIDE button

[Cable Box (CBL), Satellite Receiver (SAT)/

Set-Top-Box (STB) mode only]

The use of this button is only applicable when the

remote control is in (CBL) and (SAT/STB) mode.

Press this button to access the Channel Guide of

the (CBL), and (SAT/STB).

video which are displayed on the TV screen when

available. Your local TV program guide denotes

these programs as or .

씈

PHOTO INPUT Select to access your pictures from a

digital camera, MMC/SD Flash memory

or memory card connected to the Photo

Input in the front panel of the Plasma

TV (see pages 27-28).

INFO button

Press this button when you want to check the

channel being received, the picture source, if

the channel has stereo (ST) or second audio

program (SAP), the time, CHANNEL ID and if

the TIMER is set.

씉

Event timer

10:00 AM

Event timer

10:00 AM

The Remote Control

How to Use the Remote to Control Your TV

1. Press the INPUTS button to cycle through the

INPUTS selections until the PHOTO INPUT is

selected. Press the SELECT button or

CURSOR PAD .

2. Press the CURSOR PAD  or  to access the

next or previous photo.

3. Press the SELECT button to view THUMBNAIL.

4. Use the CURSOR PAD buttons , ,  or 

and the SELECT button to navigate and select

individual chosen photos.

5. Press the picture number to jump from picture

to picture.

6. Press the INFO button to access PHOTO Input

menu and to view Photo information.

7. Press the CURSOR PAD  or  and the

SELECT button to navigate and select the

PHOTO Input menu.

PHOTO INPUT

This feature is useful for viewing digital still pictures from your digital camera, MMC/SD memory cards using the

Photo Input in the front panel of the TV.

Next SEL Thumbnail [0-9] Jump

NOTES: 1. Contrast will decrease automatically if stationary images such as digital still photos are left

on the screen for more than 3 minutes.

The maximum number of digital Photos that can be displayed is 999.

3. Press INFO button to show Picture Numbers in Thumbnail view, plus other information in

individual photos.

4. Digital photos recorded on a DVD-RAM disc may not work with this Photo Input.

5. Certain types of digital cameras may not work with this Photo Input.

6. Digital cameras with low battery power may not properly display your photos in this input.

7. The screen may show “Input device not detected” if the digital camera’s large capacity

memory is fully loaded, or because of slow access time on some digital cameras. Please

wait 1 or 2 minutes before checking your Photo Input connections.

Please Enter

Picture Number

HDMI 1

HDMI-Front

Photo Input

Input 1

Move SEL Sel.

Air / Cable

No. 02/08

06/13/05

2048x1536

DSC00467

No. 02/08

06/13/05

2048x1536

DSC00467

Rotate

Slideshow

Picture No.

Date

Resolution

File Name

The Remote Control

test-bleed 3/3/06 10:18 AM Page 102

How to Use the Remote to Control Your TV

ROTATE

Select this menu item to rotate selected photos

either clockwise (CURSOR PAD ) and

counterclockwise (CURSOR PAD ).

SLIDESHOW

Select this menu item to start a slideshow of the

digital photos. While the Interval sub menu is

highlighted, press the SELECT button to cycle

through the interval time from 5, 10 and 30 seconds.

Press the SELECT button to stop on a chosen

picture of the slideshow. After 30 seconds, the

slideshow will resume or press the SELECT button

again to continue with the slideshow.

NOTES: 1. Automatic contrast reduction also applies during SLIDESHOW, then press any button to

continue.

2. Photo file names modified on a computer should be 8 characters (Ex. ABCD1234.jpg). 1st

character: letters; 2nd to 4th: letters or numbers; 5th to 8th: numbers. Photo files should be

first placed on a sub directory name with 8 characters (Ex. 123ABCDE). 1st to 3rd: number;

4th to 8th: letters. The sub directory then should be placed on a main directory with a

“dcim” file name format.

3. Supported image types are up to 3072 x 2304; JPEG format should conform with DCF

Standard (Design rule for Camera File System).

4. This TV set displays only digital pictures from digital cameras which meet DCF Standard.

Pictures that were copied, edited or modified on a computer may not be displayed on the TV

set.

Rotate

Slideshow Start

Rotate

Slideshow Start

Interval 5sec

The Remote Control

Rotate

test-bleed 3/3/06 10:18 AM Page 103

How to Use the Remote to Control Your TV

VOLUME (VOL), MUTE button

Press the VOLUME button (

 or ) until you obtain

the desired sound level.

To reduce the sound to one half of normal volume

(SOFT MUTE) to answer the telephone, etc., press

the MUTE button. Press the MUTE button again to

turn the sound off completely (MUTE). To restore

the sound, press the MUTE button one more time,

or VOL UP (

).

Closed Captioning will display automatically when

MUTE/SOFT MUTE is on and Closed Caption is set

toAUTO (see page 60).

When the TV power is turned off at a volume level

31 or greater, the volume level will default to 30

when the TV is turned on. However, if it is set to a

level 30 or less, the volume level will be at the level

it was set when the TV is turned on.

CHANNEL SELECTOR/FAVORITE CHANNEL

(FAVCH)/ENTER buttons

The CHANNEL SELECTOR buttons are used to

select channels, lock access code, etc. Use the

CHANNEL SELECTOR buttons to enter one, two,

or three numbers to select channels. Enter

first

for channels 1 to 9, or simply press the single digit

channel you wish to tune then press the ENTER button

for the TV to tune. Channel selection may also be

performed by CHANNEL (CH) UP (

) or

CHANNEL (CH) DOWN (

).

Press the FAV CH button to switch to Favorite

(FAV) channel mode. You will know you are in

Favorite Channel mode when (FAV) is displayed

and the displayed channel is GREEN. Press it

again to return to your regular tuned channels. You

can add any channel to your Favorite channel list

by pressing and holding down the FAV CH button

until the displayed channel turns from WHITE to

highlighted GREEN. You can also delete a channel

from your favorite channel list by pressing and

holding down the FAV CH button until the

displayed channel turns highlighted GREEN to

WHITE.

(-) DASH button

LAST CHANNEL button

Press this button to toggle between the current and

last channel viewed.

RECORD button

Press to record programs when the remote is in

PVR/VCR mode.

씋

Cable 6

FAV Cable 6

Cable 6

Volume 8

Soft Mute 8

Mute 8

씊

Use the (-) DASH button with the CHANNEL

SELECTOR buttons to enter Digital Channels that

have subchannel numbers indicated by (-) DASH

(example 15-1).

The Remote Control

Your HITACHI Plasma TV incorporates one Tuner

technology designed for improved viewing enjoyment.

This feature allows you to view Digital Channels

and Video inputs on both the main picture and

sub picture simultaneously, with separate control.

Analog channels cannot be viewed in PIP mode.

Please see table below for PIP availability.

To select between main picture and PIP sub picture,

use the CURSOR PAD button the remote. The Green

highlighted channel display will move with every press

of the CURSOR PAD buttons.

The Picture-in-Picture feature is convenient when you

want to watch more than one program at the same

time.You can watch a TV program while viewing other

programs from any of the video inputs.

Use connection at right to view VCR program as a

sub picture while viewing another program as main

picture (CABLE/AIR Digital channel).

햲

PIP button

Press the PIP button and a sub-picture will appear

SPLIT mode . To change back to normal viewing

press the

EXIT button.

NOTE: 1. In SPLIT mode, press the CURSOR PAD ( t or u ) to enable the sub-picture sound.

SPLITMODEPICTURE-IN-PICTURE

Split Mode PIP displays the main picture and

subpicture evenly on the screen.

SWAP

Main Picture

Sub Picture

Picture-In-Picture (PIP)

CABLE

Air signal

Back of

VCR

OUTPUT

VCR

VIDEO OUT AUDIO OUT

햲

PIP Specifications Table

Digital Channel

1080i 720p 480p 480p 480i 480i 1080i 720p 480p 480p 480i 480i

16x9 16x9 16x9 4x3 16x9 4x3 16x9

1080p(*)

16x9 16x9 16x9 4x3 16x9 4x3

Component

Composite

S-IN

HDMI

Digital Channel

(Air or Cable)

Sub Picture

Main Picture

Component/Composite/S-lN/HDMI

SPLIT

PIP

Mode

1080i 16x9

------

720p 16x9

------

480p 16x9

------

480p 4x3

- - - - - -

480i 16x9

------

480i 4x3

- - - - - -

1080i 16x9

720p 16x9

480p 16x9

480p 4x3

Yes Yes Yes Yes Yes Yes

1080p (*) 16x9

Yes Yes Yes Yes Yes Yes

480i 16x9

480i 4x3

Yes Yes Yes Yes Yes Yes

----- -

- - - - - -

Yes Yes Yes Yes Yes Yes

Yes

(*) HDMI Input only

The Remote Control

Your HITACHI Plasma TV incorporates one Tuner

technology designed for improved viewing enjoyment.

This feature allows you to view Digital Channels

and Video inputs on both the main picture and

sub picture simultaneously, with separate control.

Analog channels cannot be viewed in PIP mode.

To select between main picture and PIP sub picture,

use the CURSOR PAD button the remote. The Green

highlighted channel display will move with every press

of the CURSOR PAD buttons.

The Picture-in-Picture feature is convenient when you

want to watch more than one program at the same

time.You can watch a TV program while viewing other

programs from any of the video inputs.

Use connection at right to view VCR program as a

sub picture while viewing another program as main

picture (CABLE/AIR Digital channel).

햲

PIP button

Press the PIP button and a sub-picture will appear

SPLIT mode . To change back to normal viewing

press the

EXIT button.

NOTE: 1. In SPLIT mode, press the CURSOR PAD ( t or u ) to enable the sub-picture sound.

SPLITMODEPICTURE-IN-PICTURE

Split Mode PIP displays the main picture and

subpicture evenly on the screen.

SWAP

Main Picture

Sub Picture

Picture-In-Picture (PIP)

CABLE

Air signal

Back of

VCR

OUTPUT

VCR

VIDEO OUT AUDIO OUT

햲

PIP Availability Table

Digital Channel

1080i 720p 480p 480p 480i 480i 1080i 720p 480p 480p 480i 480i

16x9 16x9 16x9 4x3 16x9 4x3 16x9

1080p(*)

16x9 16x9 16x9 4x3 16x9 4x3

Component

Composite

S-IN

HDMI

Digital Channel

(Air or Cable)

Sub Picture

Main Picture

Component/Composite/S-lN/HDMI

SPLIT

PIP

Mode

1080i 16x9

------

720p 16x9

------

480p 16x9

------

480p 4x3

- - - - - -

480i 16x9

------

480i 4x3

- - - - - -

1080i 16x9

720p 16x9

480p 16x9

480p 4x3

Yes Yes Yes Yes Yes Yes

1080p (*) 16x9

Yes Yes Yes Yes Yes Yes

480i 16x9

480i 4x3

Yes Yes Yes Yes Yes Yes

----- -

- - - - - -

Yes Yes Yes Yes Yes Yes

Yes

(*) HDMI Input only

Note: A text message will appear if the PIP feature

is used without a Digital Channel as one of the two

sources. "This function is not available. Please

consult the Owners Manual."

test-bleed 3/3/06 10:18 AM Page 33

Picture-In-Picture (PIP)

MAIN FREEZE

Press the PAUSE button to freeze one frame of the

picture you are currently viewing and the frozen

frame will show in the Main Picture. Press the EXIT

button to return to normal viewing. This feature is

useful for freezing a picture frame with addresses.

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

P.O. Box 55512

Any Town, USA 98765

Check or

Money Order Only

1-800-555-1212

SPLIT FREEZE

Press the PAUSE button to freeze the picture you

are currently viewing (only the right sub-picture will

freeze). Press the EXIT button to return to normal

viewing.

Main Picture

Sub Picture

STROBE FREEZE

Press the PAUSE button to freeze three frames of

the picture you are currently viewing (only the 3

sub-pictures will freeze). Press the EXIT button to

return to normal viewing. This feature is useful for

viewing a moving picture that has many details, for

example, a close play in a sporting event or a golf

swing.

NOTE: 1. The default FREEZE mode is the MAIN

freeze followed by the SPLIT freeze and

then the STROBE freeze. The last FREEZE

mode you selected before you pressed the

EXIT button will be the one that comes up

after pressing the PAUSE button again.

2. Each freeze frame in Strobe Freeze is

delayed about 0.1 (1/10) second.

The Remote Control

햳

햳PAUSE button

Press the PAUSE button repeatedly to toggle

between FREEZE modes (Main Freeze, SPLIT and

STROBE). This is convenient when trying to write

down the address for a mail order company,

recording statistics for a sporting event, etc. To

return the picture to motion, press the EXIT

button.

FUNCTION FOR YOUR CABLE BOX.

This remote is designed to operate different types of

cable boxes. You must first program the remote to

match the remote system of your cable box (refer to

pages 37-38 for pre-codes).

1. Turn ON your cable box.

2. To switch to Cable (CBL) pre-coded mode, use the

SOURCE SELECT button on the remote control

to position the LED light to the corresponding

selection SAT/CBL.

3. Hold down the SOURCE SELECT button on the

remote and enter the four digit preset code that

matches your cable box as shown on pages 37-38.

Release the SOURCE SELECT button. The indicator

light will flash 3 times if the code was accepted.

4. Aim the remote at the cable box and press the

POWER button. The remote will turn off your cable

box when the correct four digit preset code is

entered. When this occurs, the remote control is

programmed for your cable box. If the cable box

does not turn off, try a different four digit preset

code.

5.The remote will now control your Cable box.

NOTE: 1. If your cable box cannot be operated after

performing the above procedures, your

cable box code has not been precoded

into the remote.

2. In the unlikely event that your cable box

cannot be operated after performing the

above procedures, please consult your

cable box operating guide.

3. The remote control will remember the

codes you have programmed until the

batteries are removed from the

remote control. After replacing the

batteries repeat the entire programming

procedure as stated above.

햲 PRECODED CABLE BOX buttons

These buttons transmit the chosen precoded cable

codes.

햳 EXCLUSIVE TV buttons

These buttons are for operating the TV.

MY CABLE BOX CODE IS:

NOTE: Refer to instruction manual of the Cable Box

for operation of the buttons exclusively for

the Cable Box.

The Remote Control for Cable Box Functions

햲

햳

햲

햳

햲

햳

햲

OPERATING THE PRECODED

The Remote Control

test-bleed 3/3/06 10:18 AM Page 35

YOUR SET-TOP-BOX/SATELLITE RECEIVER.

This remote is designed to operate different types of

set-top-box/satellite systems. You must first program

the remote to match the remote system of your set-

top-box/satellite systems (refer to pages 37-38 for pre-

codes).

1. Turn ON your set-top-box/satellite systems.

2. To switch to set-top-box/satellite (SAT) pre-coded

mode, use the SOURCE SELECT button on the

remote control to position the LED light to the

corresponding selection SAT/CBL.

3. Hold down the SOURCE SELECT button on the

remote and enter the four digit preset code that matches

your set- top-box/satellite receiver as shown on page

37-38. Release the SOURCE SELECT button. The

indicator light will flash 3 times if the code was accepted.

4. Aim the remote at the set-top-box/satellite receiver

and press the POWER button. The remote will turn

off your set-top-box/satellite receiver when the

correct four digit preset code is entered. When this

occurs, the remote control is programmed for your

set-top-box/satellite receiver. If the set-top-

box/satellite receiver does not turn off, try a

different four digit preset code.

The remote will now control your set-top-box/

satellite receiver.

NOTE: 1. If your set-top-box/satellite receiver

cannot be operated after performing the

above procedures, your set-top-box/

satellite receiver code has not been

precoded into the remote.

2. In the unlikely event that your set-top-

box/satellite receiver cannot be operated

after performing the above procedures,

please consult your set-top-box/satellite

receiver operating guide.

3. The remote control will remember the

codes you have programmed until the

batteries are removed from the

remote control. After replacing the

batteries repeat the entire programming

procedure as stated above.

햲 PRECODED SET-TOP-BOX/SATELLITE

RECEIVER buttons

These buttons transmit the chosen pre-coded

set-top-box/satellite codes.

햳 EXCLUSIVE TV buttons

These buttons are for operating the TV.

MY Satellite RECEIVER/

SET-TOP-BOX CODE IS:

NOTE: Refer to instruction manual of the Set-Top-

Box/Satellite Receiver for operation of the

buttons exclusively for the Set-Top-

Box/Satellite Receiver.

The Remote Control for Set-Top-Box/Satellite Receiver

Functions

OPERATING THE PRECODED FUNCTION FOR

햲

햳

햲

햳

햲

햳

햲

The Remote Control

test-bleed 3/3/06 10:18 AM Page 36

FUNCTION FOR YOUR DVD PLAYER.

This remote is designed to operate different types of

DVD players. You must first program the remote to

match the remote system of your DVD player (refer to

pages 37-38 for pre-codes).

1. Turn ON your DVD player.

To switch to DVD pre-coded mode, use the

SOURCE SELECT button on the remote control to

position the LED light to the corresponding selection

DVD.

3. Hold down the SOURCE SELECT button on the

remote and enter the four digit preset code that

matches your DVD player, as shown on pages 37-38.

Release the SOURCE SELECT button. The indicator

light will flash 3 times if the code was accepted.

4. Aim the remote at the DVD player and press the

POWER button. The remote will turn off your DVD

player when the correct four digit preset code is

entered. When this occurs, the remote control is

programmed for your DVD player. If the DVD

player does not turn off, try a different four digit

preset code.

5.The remote will now control your DVD player.

NOTE: 1. If your DVD player cannot be operated

after performing the above procedures,

your DVD player code has not been

precoded into the remote.

2. In the unlikely event that your DVD player

cannot be operated after performing the

above procedures, please consult your

DVD player operating guide.

3. The remote control will remember the

codes you have programmed until the

batteries are removed from the

remote control. After replacing the

batteries repeat the entire programming

procedure as stated above.

햲 PRECODED DVD Buttons

These buttons transmit the chosen precoded

DVD codes.

햳 EXCLUSIVE TV Buttons

These buttons are for operating the TV.

MY DVD PLAYER CODE IS:

NOTE: Refer to instruction manual of the DVD Player

for operation of the buttons exclusively for

the DVD Player.

The Remote Control for DVD Functions

햲

햳

햲

햳

햲

햳

햲

OPERATING THE PRECODED

The Remote Control

test-bleed 3/3/06 10:18 AM Page 37

YOUR VCR/PVR (Personal Video Recorder).

This remote is designed to operate different types of

VCRs/PVRs. You must first program the remote to

match the remote system of your VCR/PVR (refer to

pages 37-38 for pre-codes).

1. Turn ON your VCR/PVR.

2. To switch to VCR/PVR pre-coded mode, use the

SOURCE SELECT button on the remote control to

position the LED light to the corresponding

selection PVR/VCR.

3. Hold down the SOURCE SELECT button on the

remote and enter the four digit preset code that

matches your VCR/PVR, as shown on pages 37-38.

Release the SOURCE SELECT button. The indicator

light will flash 3 times if the code was accepted.

4. Aim the remote at the VCR/PVR and press the

POWERbutton. The remote will turn off your PVR

when the correct four digit preset code is entered.

When this occurs, the remote control is

programmed for your VCR/PVR. If the VCR/PVR

does not turn off, try a different four digit preset

code.

5.The remote will now control your VCR/PVR.

NOTE: 1. If your VCR/PVR cannot be operated after

performing the above procedures, your

VCR/PVR code has not been precoded

into the remote.

2. In the unlikely event that your VCR/PVR

cannot be operated after performing the

above procedures, please consult your

VCR/PVR operating guide.

3. The remote control will remember the

codes you have programmed until the

batteries are removed from the

remote control. After replacing the

batteries repeat the entire programming

procedure as stated above.

햲 PRECODED VCR/PVR Buttons

These buttons transmit the chosen precoded

VCR/PVR codes.

햳 EXCLUSIVE TV Buttons

These buttons are for operating the TV.

MY VCR/PVR CODE IS:

NOTE: Refer to instruction manual of the VCR/PVR

for operation of the buttons exclusively for

the VCR/PVR.

The Remote for VCR/PVR Functions

OPERATING THE PRECODED FUNCTION FOR

햲

햳

햲

햳

햲

햳

햲

The Remote Control

test-bleed 3/3/06 10:18 AM Page 40

INPUT ACCESS

This optional feature allows the user of the remote

control to setup it’s SOURCE SELECT button to access

the specified input of the TV. Setup for this feature is

applicable to the remote control’s normal mode only and

only applies to the DVD, PVR/VCR and SAT/CBL

modes.

1.Select the desired device mode (DVD, PVR/VCR,

SAT/CBL) by using your SOURCE SELECT button

to position the LED indicator to the corresponding

selection.

2. Hold down the SOURCE SELECT button on the

remote and enter the four digit preset code that

matches your device as shown on pages 37-38.

3. Then enter the assigned input number (1-7) that the

device is related to (refer below to Table 1).

4.Release the SOURCE SELECT button.

5. If done correctly, the device LED indicator will blink

3 times to confirm proper setup.

6. The remote will now control the desired device.

7. Pressing the INPUTS button will now access the

video input of the desired device.

SETUP EXAMPLE (Hitachi DVD with precode

0573 connected to INPUT 1 of the TV)

 Select DVD mode by using your SOURCE SELECT

button to position the LED indicator to DVD.

 Hold down the SOURCE SELECT button and

press the numbers 0, 5, 7 and 3.

 Then press the number 1 for the assigned input

number of the DVD player.

Release SOURCE SELECT button.

 If done correctly, the device LED indicator will blink

3 times to confirm proper setup.

 The remote will now control the DVD player.

 Press the INPUTS button to instantly access the

video input of your DVD on Input 1.

NOTE: 1. This feature is optional

2. Assigned input numbers can be used more

than once if applicable.

How to Use the SOURCE SELECT Button

HDMI- FRONT 7

ASSIGNMENT NUMBER

INPUT

Table 1



, , 





HDMI 2 6

HDMI 1 5

VIDEO- FRONT 4

VIDEO 3 3

VIDEO 2 2

VIDEO 1 1

The Remote Control



, , 

test-bleed 3/3/06 10:18 AM Page 41

Remote Control Codes

Cable BRAND Codes General Instrument ........0869 Daewoo ......................... 0045, 0278, 0020, 0561 1479

BC ........................ 0003,0008,0011 GOI.................................0775,1775 1278 Panasonic ..................... 1062,0035, 0162, 0225,

mericast ................ 0899 Goodmans .....................1246 Daytron ......................... 0020 0616,1035,1162,1262

mino ......................1602 Hisense ..........................1535 Dell ................................ 1972 Penney .......................... 0035, 0037, 0240, 0042,

Bell South ............... 0899 Hitachi ........................... 0819,1250 Denon ........................... 0042 0038,1035,1237

Clearmaster ............ 0883 HTS ............................... 0775,1775 DirecTV ......................... 0739 Pentax ........................... 0042,0065,0105

ClearMax ................ 0883 Hughes Network System 1142,0749,1749,1442 Durabrand ..................... 0039,0038 Philco ............................ 0035,0479

Coolmax ................. 0883 iLo...................................1535 Dynatech ....................... 0000 Philips ........................... 0035,0081,0062,0618,

Digeo ...................... 1187 JVC.................................0775,1775 Electrohome .................. 0037 0739,1081,1181

Director ................... 0476 LG ..................................1226,1414 Electrophonic ................ 0037 Pilot ............................... 0037

General Instrument.. 0476,0810,0276,0003, Magnavox ......................0724,0722 Emerex ..........................0032 Pioneer ......................... 0067

0011

Memorex ....................... 0724 Emerson ........................0037, 0184, 0000, 0121, Polk Audio ..................... 0081

GoldStar...................0144 Mitsubishi ...................... 0749 0043,0209,0002,0278, Portland .........................0020

Hamlin .....................0009,0273 Motorola ........................ 0869 0061,0208,0479,0561, Presidian ........................1593

Hitachi ..................... 0011,1421 NEC ...............................1270 0593,1278,1479,1593, Profitronic ...................... 0240

i3 Micro ....................1602 Next Level ..................... 0869 Fisher ............................ 0047,0104 Proscan ......................... 0060,0202,0760,0761

Jerrold ..................... 0476,0810,0276,0003 Pace .............................. 0887 Fuji ................................ 0035,0033 1060

0012,0011

Panasonic ..................... 0247,0701 Funai ............................. 0000,0593,1593 Protec ............................0072

Memorex ................. 0000 Paysat ........................... 0724 Garrard ......................... 0000 Pulsar ............................ 0039

Motorola .................. 1376,0476,0810,0276 Philips ............................1142, 0749, 1749, 0724, Gateway ........................ 1972 Quarter .......................... 0046

1187,1254,1106 1076,0722,0099,1442

GE ................................. 0060,0035,0240,0065, Quartz ........................... 0046

Multitech ..................0883 Proscan ......................... 0392,0566 0202,0760,0761,0807, Quasar .......................... 0035,0162,1035,1162

MultiVision ...............0012 Proton ............................1535 1035, 1060 RadioShack .................. 0000,1037

Myrio ........................1602 RadioShack ...................0869 Go Video ....................... 0432,0526 Radix ............................. 0037

Pace ........................1877,0237,0008 RCA ...............................0566,0855,0143,1392 GoldStar ........................ 0037,0038,1237 Randex ..........................0037

Panasonic ............... 0000,0107 Samsung .......................1377,1276,1108,1109, Gradiente ...................... 0000 RCA ...............................0060,0240,0042,0149,

Paragon ...................0000 1442,1609 Harley Davidson ............0000 0065,0105,0106,0202,

Philips ......................1305,0317 Sanyo ............................ 1219 Harman/Kardon .............0081,0038 0760,0761, 0807, 0880,

Pioneer ....................1877,0877,0144,0533 SKY ............................... 0856 Harwood ........................0072 1035,1060

Pulsar.......................0000 Sony .............................. 0639,1639,1640 Headquarter .................. 0046 Realistic .........................0035,0037,0048,0047,

Quasar..................... 0000 Star Choice ................... 0869 Hewlett Packard............. 1972 0000,0104,0046,0062

RadioShack .............0883 Tivo ............................... 1142,1442 HI-Q ...............................0047 ReplayTV ...................... 0614,0616

RCA .........................1256 Toshiba ......................... 0749,1749,0790,1285 Hitachi ........................... 0000,0042,0041,0065, Ricavision ......................1972

Regal .......................0279,0273 UltimateTV .................... 1392,1640 0089,0105,0543,0544 Runco ............................0039

Rembrandt .............. 0011 Uniden ...........................0724, 0722 Howard Computers ....... 1972 Samsung ....................... 0240,0045,0739,1014

Runco ..................... 0000 US Digital .......................1535 HP ................................. 1972 Sanky ............................ 0048,0039

Samsung .................0144 USDTV ...........................1535 Hughes Network System.0042,0739 Sansui ........................... 0000,0067,0209,0041,

Scientific Atlanta ......1877,0877, 0477, 0008 Voom .............................0869 Humax .......................... 0739 0271,0479,1479

Sejin ........................ 1602 Zenith ............................ 0856,1856 Hush ..............................1972 Sanyo ............................ 0047,0240,0104,0046,

Signature................. 0011 iBUYPOWER .................1972 0159

Sony ........................1006 DBS/PVR Codes Jensen .......................... 0041 Scott .............................. 0184,0045,0121,0043

Starcom .................. 0003 Combo BRAND JVC ............................... 0067,0041,0008 Sears .............................0035,0037,0047,0000,

Supercable ..............0276 DirecTV ..........................1377,0392,0639,1142, KEC ...............................0037, 0278 0042,0104,0046,0105,

Supermax ................0883 1076,0099,1392,1442, Kenwood ....................... 0067,0041,0038 1237

Thomson ................. 1256 1640 KLH ............................... 0072 Sharp .............................0048,0062,0807,0848

Tocom ..................... 0012 Dish Network System ....1505,0775 Kodak ............................ 0035,0037 Shintom .........................0072

Torx .........................0003 Dishpro ..........................1505,0775 LG ................................. 1037 Shogun ..........................0240

Toshiba ................... 0000 Echostar ........................ 1505, 0775 Linksys .......................... 1972 Singer ............................0072

Tristar ......................0883 Expressvu ..................... 0775 Lloyd's ........................... 0000,0208 Sonic Blue .....................0614,0616

V2 ............................0883 Hughes Network System..1142, 1442 Logik ............................. 0072 Sony .............................. 0035,0032,0033,0000,

Viewmaster ............. 0883 Motorola ........................ 0869 LXI ................................ 0037 0636,1032,1232,1972

Vision ...................... 0883 Philips ............................1142,1442 Magnasonic .................. 0593,1278 Stack ............................. 0009,1972

Vortex View .............0883 Proscan ......................... 0392 Magnavox ..................... 0035,0039,0081,0000, STS ............................... 0042

Zenith ...................... 0000,0525,0899 RCA ...............................1392 0149,0563,0593,1593, Sylvania .........................0035,0081,0000,0043,

Samsung ....................... 1442 1781 0593,1593,1781

Cable/PVR Codes

Sony ..............................

0639,1640 Magnin .......................... 0240 Symphonic .................... 0000,0593,1593

Combo BRAND

Star Choice ...................

0869 Marantz ......................... 0035, 0081 Systemax ...................... 1972

mericast ................ 0899

Marta ............................. 0037 Tagar Systems .............. 1972

Digeo ....................... 1187

VCR BRAND Codes Matsushita .................... 0035, 0162, 1162 Tatung ........................... 0041

General Instrument ..0810

ABS ............................... 1972 Media Center PC .......... 1972 Teac .............................. 0000,0041

Jerrold ..................... 0810

Admiral .......................... 0048,0209 MEI ............................... 0035 Technics ........................0035,0162

Motorola .................. 1376,0810,1187,1106

Adventura ..................... 0000 Memorex ...................... 0035,0162,0037,0048, Teknika ..........................0035,0037,0000

Pace ........................ 1877,0237

Aiko ............................... 0278 0039,0047,0240,0000, Thomas ......................... 0000

Pioneer .................... 1877,0877

Aiwa .............................. 0037,0000,0124,0307 0104,0209,0046,0307, Tivo ............................... 0618, 0636, 0739, 1996

RCA ......................... 1256

Akai ............................... 0041,0061,0106,0175 0479,1037, 1162, 1237 TMK .............................. 0240,0208

Scientific Atlanta ...... 1877,0877

Alienware ...................... 1972 1262 Toshiba ......................... 0045,0043,0845,1008,

Sony ........................ 1006

America Action .............. 0278 MGA ............................. 0240, 0043, 0061 1145, 1972, 1996

Supercable .............. 0276

American High .............. 0035 MGN Technology ......... 0240 Totevision ......................0037,0240

Thomson ................. 1256

Asha .............................. 0240 Microsoft ...................... 1972 Touch .............................1972

Zenith ...................... 0899

Audiovox ....................... 0037,0278 Mind ............................. 1972 Unitech .......................... 0240

Beaumark ..................... 0240 Minolta .......................... 0042, 0105 Vecto

0045

SATELLITE BRAND Codes Bell & Howell ................. 0104 Mitsubishi ...................... 0067, 0043, 0061, 0807 Vector Research ............0038

(Set Top Box) Broksonic ...................... 0184,0121,0209,0002 Motorola ........................ 0035,0048 Video Concepts .............0045,0061

lphaStar ................. 0772 0479,1479 MTC .............................. 0240,0000 Videomagic ....................0037

Chaparral ................. 0216 Calix .............................. 0037 Multitech ....................... 0000,0072 Videosonic .................... 0240

Crossdigital .............. 1109 Canon ........................... 0035 NEC .............................. 0104,0067,0041,0038 Viewsonic ...................... 1972

DirecTV .................... 1377,0392,0566,0639, Capehart ....................... 0020 Nikko ............................ 0037 Villain .............................0000

1639,1142,0247,0749,

Carver ........................... 0081 Niveus Media ................ 1972 Voodoo ..........................1972

1749,0724,0819,1856,

CCE .............................. 0072,0278 Noblex .......................... 0240 Wards ............................0060,0035,0048,0047,

1076,1108,0099,1109,

Citizen ........................... 0037,0278,1278 Northgate ...................... 1972 0081,0240,0000,0042,

1414,1442,1609,1392,

Colt ............................... 0072 Olympus ....................... 0035 0072,0149,0062,0760

1640

Craig ............................. 0037,0047,0240,0072 Onkyo ........................... 0222 White Westinghouse ..... 0209,0072

Dish Network System1505,1005,0775,1775 0271 Optimus ........................ 1062, 0162, 0037, 0048, XR-1000 ........................ 0035,0000,0072

Dishpro 1505,1005,0775,1775 Curtis Mathes ................ 0060,0035,0162,0041 0104,0432,0593,1048, Yamaha .........................0038

Echostar 1505,1005,0775,1775 0760,1035 1162,1262 Zenith ............................ 0039,0033,0000,0209,

Expressvu 0775,1775 Cybernex .......................0240 Optonica ....................... 0062 0479,1139,1479

GE 0566 CyberPower .................. 1972 Orion ............................. 0184,0209,0002,0479 ZT Group .......................1972

The Remote Control

test-bleed 3/3/06 10:18 AM Page 42

Remote Control Codes

DBS/PVR Codes Enterprise 0591 Sony 0533,1533,0864,1033,

Combo BRAND ESA 0821,1268 1431

Hughes Network Systems 0739 Fisher 0670,1919 Sova 1122

Philips 0739 Funai 0675,1268,1334 Sungale 1074

Samsung 0739 Gateway 1073,1077,1158 Superscan 0821

GE 0522,0815,0717 SVA 0860,1105

PVR BRAND Codes Go Video 0744,0715,0741,0783, Sylvania 0675,0821,1268

ABS 1972 0833,0869,1044,1075, Symphonic 0675,0821

Alienware 1972 1099,1144,1158,1304, Teac 0758,0790,0809

CyberPower 1972 1730 Technics 0490,0703

Dell 1972 Go Vision 1071,1072 Technosonic 0730

DirecTV 0739 GoldStar 0741 Techwood 0692

Gateway 1972 GPX 0699,0769 Terapin 1031

Hewlett Packard 1972 Greenhill 0717 Theta Digital 0571

Howard Computers 1972 Harman/Kardon 0582,0702 Toshiba 0503,0695,1045,1154

HP 1972 Hitachi 0573,0664,1247,1919 Tredex 0799,0800,0803,0804

Hughes Network Systems 0739

Hiteker 0672 TYT 0705

Humax 0739 iLo 1348 Urban Concepts 0503

Hush 1972 Initial 0717 US Logic 0839

iBUYPOWER 1972 Insignia 1268 Venturer 0790

Linksys 1972 Integra 0627 Vizio 1064,1226

Media Center PC 1972 JBL 0702 Xbox 0522

Microsoft 1972 Jensen 1016 Yamaha 0490,0539,0545

Mind 1972 JSI 1423 Zenith 0503,0591,0741,0869

Niveus Media 1972 JVC 0558,0623,0867,1164 Zoece 1265

Northgate 1972 jWin 1049,1051

Panasonic 0616 Kawasaki 0790 DVD-R Codes

Philips 0618,0739 Kenwood 0490,0534,0682,0737 Accurian 1416

RCA 0880 KLH 0717,0790,1020,1149 Apex Digital 1056

ReplayTV 0614,0616 1261 Aspire Digital 1168

Samsung 0739 Konka 0711,0719,0720,0721 Coby 1086

Sonic Blue 0614,0616 Koss 0651,0896,1423 CyberHome 1129

Sony 0636,1972 Landel 0826 Funai 0675,1334

Stack 0009,1972 Lasonic 0798,1173 Gateway 1073,1158

Systemax 1972 Lenoxx 1127 Go Video 0741,1158,1304,1730

Tagar Systems 1972 LG 0591,0741,0801,0869 iLo 1348

Tivo 0618,0636,0739 LiteOn 1058,1158,1416,1440 JVC 1164

Toshiba 1008,1972,1996 Loewe 0511 LG 0741

Touch 1972 Magnavox 0503,0539,0646,0675, LiteOn 1158,1416,1440

Viewsonic 1972 0821,1268 Magnavox 0646,0675

Voodoo 1972 Malata 0782,1159 Panasonic 0490

ZT Group 1972 Marantz 0539 Philips 0646

Memorex 0695,0831,1270 Pioneer 0631

Microsoft 0522 Polaroid 1086

DVD BRAND Codes Mintek 0839,0717 RCA 0522

Mitsubishi 1521,0521 Samsung 0490

Accurian 1072,1416 Momitsu 1082 Sensory Science 1158

Advent 1016 NAD 0741 Sharp 0675

Aiwa 0641

1089

NEC 0785 Sony 1033,1431

Akai 0695,0770,0899, Nesa 0717 Sylvania 0675

Alco 0790 Next Base 0826 Zenith 0741

Allegro 0869 NexxTech 1402

Amphion Media Works 0872 Norcent 1003,0872,1107,1265

AMW 0872

0794

Onkyo 0503,0627,0792

Apex Digital 0672,0717,0755,

,0830

OptoMedia Electronics 0896

0795,0796,0797

,1061

Oritron 0651

1004,1020,1056 Panasonic 0490,0632,0703,1362,

1100 1462,1490,1762

Arrgo 1023 Philco 0690,0733,0790,0862,

Aspire Digital 1168,1407 1855,2000

Audiologic 0736,

1072

Philips 0503,0539,0646,0675,

Audiovox 0790,1041,1071, 0854,1260,1267,1354

1121,1122 Pioneer 0525,0571,0631,0632

Axion 1071,1072 Polaroid 1020,1061,1086

B & K 0655,0662 Polk Audio 0539

Blaupunkt 0717 Portland 0770

Blue Parade 0571 Presidian 0675,1072

Broksonic 0695,0868 Prima 1016

Cambridge Soundworks 0690 Proscan 0522

Cinea 0831 ProVision 0778

CineVision 0876,0833,0869 Qwestar 0651

Citizen 1277 RCA 0522,0571,0717,0790,

Coby 0778,0852,1086,1107 0822,1022,1132,1193

1165,1177,1351 Rio 0869

Craig 0831 Rotel 0623

Curtis Mathes 1087 Rowa 0823

CyberHome 0816,0874,1023,1024 Sampo 0698,0752

1117,1129,

0869

Samsung 0490,0573,0820,0899,

Daewoo 0784,0705,0833,

1242

1044,1075

1169,1172,1234, Sansui 0695

Denon 0490,0634 Sanyo 0670,0695,0873,1919

Desay 1407 Sensory Science 1158

Disney 0675,1270 Sharp 0630,0675,0752,1256

Dual 1068,1085 Sharper Image 1117

Durabrand 1127 Sherwood 0633,0770,1043,1077

DVD2000 0521 Shinsonic 0533,0839

Emerson 0591,0675,0821,1268 Sonic Blue 0869,1099

The Remote Control

NOTE: The On Screen Display (OSD) for the different submenus shown in next pages are for illustration

purposes only, therefore; doesn't reflect the actual apearance of the OSD of your HITACHI Plasma TV.

Channel Manager

Setup

Timers

Locks

Audio

Video

Move

SEL

Select

This part of the screen shows

which selections are available.

different features on your HITACHI Plasma TV.

On-Screen Display

This part of the screen

shows which Remote

Control buttons to use.

1. Press MENU on the remote control to display the

2. Use the CURSOR PAD (buttons ,, and )

and highlight a different feature of the On-Screen

Display menu. Press the SELECT button to select.

3. Press EXIT on the remote control to quickly exit

from a menu.

Timers

Locks

Channel Manager

Audio

On-Screen Display

Picture Mode Select between 3 pictures modes;

Day Dynamic, Day Normal and Night.

Contrast Adjust contrast.

Brightness Adjust brightness.

Color Adjust color.

Tint Adjust tint.

Sharpness Adjust sharpness.

Color Temperature Set this to High for less intense

color with more blue, set to

Medium for natural color, set to

Standard for standard colors.

Black Enhancement Enhance picture brightness in

light scenes.

Contrast Mode Use this function to choose

between two Contrast Mode

settings.

Noise Reduction Reduces conspicuous noise in

the picture.

Auto Movie Mode Turn On/Off the 3:2 Pulldown

detection feature.

Aspect Choose the picture format

aspect ratio.

Black Side Panel Set the side bars from gray to

black when watching 4:3 signals

in standard mode.

Reset Video Settings Choose to Reset Video Settings

to factory settings.

Treble Adjust the treble.

Bass Adjust the bass.

Balance Adjust the balance.

Audio Source Select between three Audio

Sources.

Internal Speakers Select internal or external

speakers.

Auto Noise Cancel Eliminates the noise between

stations.

Perfect Volume Adjust volume in fixed setting.

Loudness Adjust Loudness.

Language Select Language options if

available.

Digital Output Select Optical Output options.

DRC Select Dynamic Range

Compression to ON or OFF.

NOTE: The Language, Digital Output, and the

Dynamic Range Compression feature of the

Audio OSD are only available for Digital

channels.

Auto Channel Scan Set Auto Channel Scan.

Channel List Set Channel List.

Change Access Code Change Lock access code.

Engage Lock Choose to lock channel,

and/orFront panel.

Movie Ratings Block various types of movies

and video types based on

motion picture ratings.

TV Ratings Block various types of movies

and television programming

based on a parental guide

ratings.

Canadian Ratings (ENG)

Block various types of movies

and television programming

based on the Canadian ratings

system.

Canadian Ratings (FRN)

Block various types of movies

and television programming

based on the Canadian French

ratings system.

Set the Clock Set Clock Settings.

Set Sleep Timer Set Sleep Timer intervals

(30 min. intervals, 00:30-3:00).

Set Day/Night Timer Set Day/Night picture mode

settings.

Set Event Timer Set viewing reservation for TV

programs.

Set The Menu Options Choose English, French, or

Spanish text and Background.

Set The Screen Saver

Select Screen Saver options

to prevent screen burn.

Set The Inputs

Label Video Inputs, VCR, DVD,

etc.

Set The Closed Captions Feature to display dialogue/text.

Reset The Software Select to upgrade TV software.

Set The Quick Start Options Select the TV Quick Start Up

options.

NOTE: 1. The Signal Meter feature of the Channel

Manager OSD is only available for Digital

channels.

Video

Region 5 Ratings system for DTV Signal

to block various types of programs.

Setup

Surround Select Surround settings (Off,

Wide, Normal)

Bass Boost Select Bass Boost option ON or OFF.

MPEG NR Reduces mosquito noise in

the picture.

Signal Meter Access Signal Meter.

Video

On-Screen Display

Select VIDEO to adjust picture settings and improve

picture quality. You can independently customize each of

the Video Inputs to your preference to increase viewing

performance and pleasure depending upon the video

program being viewed. If RESET is selected, only the

selected input will reset to initial conditions.

Picture Mode

Use this function to choose from automatic picture

settings to optimize your TV’s performance.

1. Use the CURSOR buttons

 or  to highlight and

select PICTURE MODE settings (Day-Normal,

2.Then press the SELECTbutton to set the mode and

return to the Video menu or press EXITto quit menu.

3. There are 3 Picture Modes available for the customer

Day (Dynamic) , Day (Normal) and Night mode.

Day (Dynamic) is the original factory preset mode , this

can be changed by adjusting any video setting to your

desire conditions. Day ( Normal ) can be used as a

second video setting for daytime viewing. Night is set

to watch programing during nigthtime.

1. Use the CURSOR PAD

 or  to highlight the function to be adjusted.

2. Press the SELECT button or the CURSOR PAD

 to select the function settings.

3. Press the CURSOR PAD

 or  to adjust the function.

4. Press MENU to return to main menu.

5. Press EXIT to quit menu.

Contrast

Use this function to change the contrast between black

and white levels in the picture.

Brightness

Use this function to adjust overall picture brightness.

Color

Use this function to adjust the level of color in the picture.

Tint

Use this function to adjust flesh tones so they appear

natural.

Sharpness

Use this function to adjust the amount of fine detail in the

picture.

Day-Dynamic or Night).

Contrast Mode

Black Enhancement

Color Temperature

Sharpness

Tint

Color

Brightness

Contrast

Picture Mode Day (Dynamic)

100%

50%

62%

50%

High

Dynamic

Picture Mode Day (Dynamic)

Video

Cable

Next/Prev Select

SEL Return

Move SEL Select

Setup

Timers

Channel Manager

Locks

Audio

Video

Move

SEL Select

Contrast 100%

Next/Prev Change

SEL Return

Video

On-Screen Display

Color Temperature

Set this to High for cooler color with more blue, set to Medium for more natural color, set to Standard for accurate

color .

Black Enhancement

Use this function to enhance the shadow detail in dark scenes using the settings off, low, middle and high.

NOTE: 1. If CONTRAST is selected, you are adjusting CONTRAST. The additional menu items BRIGHTNESS,

COLOR, TINT, and SHARPNESS can be selected and adjusted in the same manner.

2. It may be necessary to adjust TINT to obtain optimum picture quality when using the COMPONENT

VIDEO Y-P

BPR input jacks.

3. CABLE and AIR share a Video setting. Also, each of the video inputs have their own independent

settings.

Contrast Mode

Use this function to choose between two Contrast Mode settings. Set to DYNAMIC for darker images more in the

level of Black, set to NORMAL for a balanced White to Black level.

Noise Reduction

The NOISE REDUCTION function automatically reduces conspicuous noise in the picture without degrading

picture quality. Set NOISE REDUCTION to OFF if the TV experiences picture blocking.

Auto Movie Mode

The AUTO MOVIE MODE function turn ON or OFF the 3:2 PULLDOWN DETECTION SPECIAL FEATURE.

Theatrical movies are shot on film at 24 frames or still pictures per second, instead of 30 frames or 60 fields like

video. When film is transferred to video for television viewing, the disparity between the two frame rates must be

reconciled. This involves a process known as 3:2 pulldown.

When AUTO MOVIE MODE is turned ON from the VIDEO menu, your Hitachi Plasma Television will activate the

circuitry for this special feature to improve video performance when watching film based sources.

Black Side Panel

The BLACK SIDE PANEL function turns the side bars

from gray to black when watching 4:3 signals in

Standard

mode or use of the PIP modes.

1. Press the CURSOR PAD  or  to set to ON or OFF.

2. Press EXIT to quit menu or select SET BLACK SIDE

PANEL to return to the previous menu.

NOTE: 1.

To prevent screen damage when watching 4:3 signal, turn off the BLACK SIDE PANEL. It is

recommended to watch 4:3 signal with gray side bar.

Black Side Panel Off

Next/Prev On/Off

SEL Return

Black Side Panel On

Next/Prev On/Off

SEL Return

MPEG NR

The MPEG NR (Noise Reduction) function automatically reduces mosquito noise in the picture without degrading

picture quality. Set MPEG NR to OFF if the TV experience picture block noise.

2. This setting return to Off automatically after TV power On/Off.

Reset Video Settings

This function allows you to Reset the Video Menu Settings of the present input and return it to the Day-Dynamic

VIDEO mode.

Use CURSOR PAD , buttons to highlight

functions.

2. Press the SELECT button or CURSOR PAD  to

select Reset Video Settings.

3. Use the CURSOR PAD  to access at the Reset

softkey.

4. Press the SELECT button to Reset the Video

Settings.

You can customize each of the Video Inputs to your

preference to increase viewing performance and

pleasure, depending upon the video program being

viewed. If RESET is selected, only the selected Input will

reset to the initial conditions as explained above.

If RESET is selected in Input 1, only Input 1 will return to

factory conditions.

Video

On-Screen Display

Aspect

Use this function to select the Picture Format Aspect

Ratio.

Auto Aspect

Automatically adjust the Aspect Ratio depending on

the input signal to fill the screen.

Mode

Manually select the Aspect Ratio.

Vertical Position

This function allows you to select when aspect style is

either 4:3 EXPANDED/ZOOM1/ZOOM2 or 16:9 ZOOM. Vertical position can be changed with these modes.

For example, it will be useful for centering the picture area at both the top and bottom of the picture with 480i/

/480p signal. Adjustable range is -10 (video center is toward bottom of screen) to +10 (video is toward top of

screen).

1. Use the CURSORPAD

orto to select menu item.

2.Press the CURSORPAD

orto adjust the function.

3.Press the EXIT to quit the MENU, or select ASPECT to return to the main menu.

NOTE:1. Vertical Position will not be available in 4:3 Standard and 16:9 Standard modes.

Auto Aspect : On

Mode 16:9 Standard1

Vertical Position : 0

Aspect

Video

Move

SEL Return

Reset Video

Video

Move

SEL Return

Select “Reset” to return to Video menu settings

on this Input to the original factory settings.

Reset

Reset Video Settings

Aspect

Black Side Panel

Auto Movie Mode

MPEG NR Off

Noise Reduction Low

Contrast Mode

Black Enhancement High

Dynamic

Off

Video

Cable

Move SEL Return

Color Temperature High

2. Vertical Position setting returns to "0" automatically after TV power On/Off.

Audio

Select AUDIO to adjust the TV to your preference and

to improve the sound quality.

1. Press CURSOR PAD  or  to select menu item.

2. Press CURSOR PAD  or  to adjust the function.

3. Press EXIT to quit the MENU, or select AUDIO to

return to the main menu.

NOTE: If TREBLE is selected you are adjusting

treble. The additional menu items BASS

and BALANCE can be selected and

adjusted in the same manner.

Treble

This function controls the high frequency audio to all speakers.

Bass

This function controls the low frequency audio to all speakers.

Balance

This function will control the left to right balance of the Plasma TV internal speakers.

On-Screen Display

Normal Surround: : Provides the surround effect by locating two or more speakers to the rear of the listener.

Off : turns off the surround sound effect.

 or 

 or 

5 channel contents with ordinary stereo contents.

Surround

Surround sound is the concept of expanding the spatial imaging of audio from one dimension ( Mono/Left-Right) to

two or three dimensions. This is often done to create a more realistic audio environment.

1.- Use CURSOR PAD to highlight surround option.

2.- Use CURSOR PAD to select Off, Normal or Wide.

Wide Surround : Reproduce much better quality 5 channel sound signals from ordinary stereo contents comparing with

normal surround technology. Wide surround enable users to enjoy sound playback in wide surround virtual area like

Bass Boost

This function allows to enhance the low frequency audio performance of your speaker system.

Setup

Timers

Channel Manager

Locks

Audio

Video

Move

SEL Select

Move SEL Return

Perfect Volume

Auto Noise Cancel

Internal Speakers

Audio Source

Bass Boost

Surround

Balance

Bass

Off

Stereo

Off

L R

50%

Audio

Treble

Audio Source

Multi-Channel Television Sound will allow you to select STEREO (a stereo broadcast), MONO (monaural sound)

used when receiving a weak stereo broadcast or SECOND AUDIO PROG (SAP) which may be a secondary

language, weather report, etc.

Internal Speakers

This function is useful when setting up the external speakers.

ON Select this feature if using the internal speakers only.

TV as Center Select this feature when setting up external speakers from a separate stereo system.

The TV’s speakers will work as the center speaker.

OFF Select this feature if you prefer to use only speakers from a separate stereo system.

Auto Noise Cancel

This function eliminates the noise between stations. If a channel is tuned and is noisy, this function will

automatically eliminate the audio for that channel.

Perfect Volume

This function will automatically adjust volume so each channel and input has the same average volume level.

Loudness

Set this function to ON to emphasize bass and treble at low volume levels.

Language

Some programs transmit more than one DTV language option. Most will have English as a default language. The

language function will allow you to select up to 4 language options (if available).

Digital Output

This function allows you to select between Dolby

®Digital and PCM. This setting is fed into Optical Output.

Dolby

Digital - Select this feature if the TV is connected to an amplifier/receiver with a Dolby®Digital only

decoder; it will provide six independent soundtrack channels through the optical output jack (Digital Audio).

NOTE: *Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

PCM - Select this feature if the TV is connected to an amplifier/receiver with a PCM only decoder; it will provide

two independent soundtrack channels through the optical output jack (Digital Audio).

DRC

Dynamic Range Compression - Use this function to

compress the range of sound volume. By compressing

the range of sound volume, it is possible not only to

suppress the output of loud sound at night but also to

raise the volume of low sound. The default setting is ON.

Use the CURSOR PAD  or  to select the chosen

options.

NOTE: The functions Language, Digital Output and DRC

are only available when viewing digital programs.

Use the functions at right if your TV is connected to an

amplifier/receiver with optical digital input with Dolby

Digital or PCM decoder capabilities.

Audio

On-Screen Display

NOTE: 1.- The DRC control affects only Dolby

Digital

signals decoded internally by the TV.

2.- DRC does not affect the Dolby Digital bitstream

available at the digital audio output.

Move SEL Select

Perfect Volume

Auto Noise Cancel

Internal Speakers

Audio Source

Bass Boost

Surround

Balance

Bass

Off

Stereo

Off

L R

50%

Audio

Move SEL Select

DRC

Digital Output

Language

Loudness

Perfect Volume

Auto Noise Cancel

Internal Speakers

Audio Source

Bass Boost

Off

Stereo

Off

Dolby Digital

1 [Unknown]

Off

Audio

Treble

Channel Manager

Select CHANNEL MANAGER to set your Antenna

options, run Auto Channel Scan, Check Signal Meter

and Set Channel List.

1.Press CURSOR PAD , buttons to highlight

function.

2. Press the SELECT button or CURSOR PAD  to

select.

Signal Meter

Select SIGNAL METER when using an indoor or outdoor

antenna. This feature will show the signal strength and

peak values of the Antenna signal to help you adjust your

antenna to optimize signal reception.

Use the CURSOR PADS and the SELECT button to

highlight and select CLOSE to exit.

NOTE: The Signal Meter will not be available (grayed

out) when watching analog channels.

Auto Channel Scan

This feature will automatically store active Analog and

Digital channels in Auto Channel Scan memory.

On-Screen Display

Channel Manager

1. Use the CURSOR buttons to highlight AIR,

CABLE (1) or CABLE(2) source.

2. Press the CURSOR buttons

 or  to highlight the

START or RESET option.

3. Press the SELECT button to select.

 or 

NOTE:

1. If certain channels are poor or not possible

in cable(1) mode, set cable source to cable(2)

by using the CURSOR buttons  or .

Move SEL Select

Channel List

Auto Channel Scan

Signal Meter

Channel Manager

Auto Channel Scan

Channel Manager

Move SEL Return

Source Air

Start Reset

Auto Channel Scan

Setup

Timers

Channel Manager

Locks

Audio

Video

Move

SEL Select

Move SEL Select

Channel List

Auto Channel Scan

Signal Meter

Move SEL Return

Signal Meter

Channel Manager

Channel 3 - 1

Strength 91

Peak 91

SNR 10

Move SEL Select

Channel List

Auto Channel Scan

Signal Meter

Channel Manager

Channel List

This function allows you to review which channels are

labeled (ID), which have been added to CHANNEL

MEMORY (SCAN), which are protected by LOCK and

which are your FAVORITE (FAV) CHANNELS.

1. Use the CURSOR PAD to navigate the Channel List.

2. Press the SELECT button to select ON or OFF on the

SCAN and LOCK columns.

3. To select LOCK column, input the access code.

(Default access code: 0000)

4. Press the FAV button to set or remove the FAVORITE

settings.

5. Press the EXIT button to return to normal viewing.

NOTE: 1. The Channel List cannot be updated by only changing the cable source. Auto Channel Scan must

be performed for the Channel List to be updated.

Channel Manager

On-Screen Display

Move Return

FAV CH# Scan Lock ID

3-1 On Off -------

4 On Off -------

5 On Off -------

6 On Off -------

7 On Off -------

8 On Off -------

9 On Off -------

10 On Off -------

No Info. --:-- AM-

--:-- AM

INFO Detail

Move SEL Select

Channel List

Auto Channel Scan

Signal Meter

Channel Manager

Channel List

Notice: United States federal law requires broadcasters to stop transmitting analog (non-digital) television signals

after February 17, 2009.

Accordingly, this TV's analog tuner will not be capable of receiving over-the-air analog television broadcasts after

such analog broadcasts are no longer available.

After February 17, 2009, this TV's analog tuner will continue to work with compatible cable and satellite TV

systems, gaming consoles, VCRs, DVD players and other similar products.

Both before and after February 17, 2009, this TV's digital tuner will receive available over-the-air digital television

broadcasts using an antenna and other digital television broadcasts using compatible cable, satellite or other

digital television system connections.

Please review this Owner's Guide for further information regarding such connections.

Locks

This function will block out the picture and sound of the

selected channel or video input.

The code to enter the Locks feature is a four digit

access code number. The factory preset code is 0000.

Use the NUMBER buttons to enter the access code.

1. Use the CURSOR PAD

, to highlight the desired

function in the LOCKS menu.

2.Press the SELECTbutton to select.

Change Access Code

1. To change the ACCESS CODE NUMBER, select

CHANGE ACCESS CODE to change the factory

preset code (0000) to your preference.

If you forget your ACCESS CODE NUMBER, use

the factory code 7777 to erase your key number.

This will reset the access code number back to the

factory preset (0000).

2. Enter a new four digit number.

3. Press EXIT to quit the menu.

Engage Lock

When ENGAGE LOCK is selected, SET CHANNEL LOCK and SET FRONT PANEL LOCK can be set individually.

When SET CHANNEL LOCK is turned on, the picture and sound for the chosen channel will be blocked out.

When FRONT PANEL LOCK is turned on, all buttons on the Front Panel will be deactivated, except the POWER

button.

When MOVIE RATINGS is selected, you can block various types of movies and video tapes based on motion

picture ratings. Picture-in-Picture will also be blocked automatically (see page 49).

WhenTV RATINGSis selected, various types of television programming based on a parental guide ratings will be

blocked. Picture-in-Picture will also be blocked automatically (see page 50).

UseCANADIAN RATINGSto block various types of movies and television programs based on the two rating

systems used in Canada that you feel may be inappropriate due to its content (see pages 51-52).

On-Screen Display

Locks

NOTE:

Use REGION 5 to block various types of movies and television pograms based on ratings systems used in U.S. that

you feel may be inappropriate due to its content (see page 53).

The REGION 5 option will operate for Digital Channels only.

Setup

Timers

Channel Manager

Locks

Audio

Video

Move

SEL Select

Please Enter Access Code

Access Code

- - - -

[#Keys] Enter Code

Move SEL Select

Region 5

Canadian Ratings (Frn)

Canadian Ratings (Eng)

TV Ratings

Movie Ratings

Engage Lock

Change Access Code

Locks

000

Movie Ratings

Use Movie Ratings to prevent viewing of any movie that

you feel may be inappropriate due to its content.

1. Use the CURSOR PAD

, to select the

MOVIE RATING category that you want to block.

2. Press SELECT to block the MOVIE RATING that you

have selected. Once rating is selected, for example

PG-13, all movies rated PG-13 and higher (R, NC-17,

and X) will be blocked.

3. Press EXIT to quit the menu or select MOVIE

RATING

to return to the previous menu.

Motion Picture Ratings Table

NOT RATED Contains no rating. Not Rated (NR) and Not Applicable (NA) programs. Movie has not

been rated or ratings do not apply.

G General audiences. All ages admitted.

PG Parental guidance suggested. Some material may not be suitable for children.

PG-13 Parents strongly cautioned. Some material may be inappropriate for children under 13.

R Restricted. Under 17 requires accompanying parent or adult guardian.

NC-17 No one 17 and under admitted.

X Adults only

NOTE: 1. A movie rating is dependent upon the movie that is viewed. If the movie does not carry a rating, the

TV will not block it.

2. Blocking NOT RATED programs may block emergency programming, sports, news, public service

announcements, religious programs and weather.

Locks

On-Screen Display

Move SEL Return

Status

Not Rated

PG-13

NC-17

Move SEL Select

Region 5

Canadian Ratings (Frn)

Canadian Ratings (Eng)

TV Ratings

Movie Ratings

Engage Lock

Change Access Code

Locks

Movie Ratings

Locks

TV Ratings

Use TV RATINGS to prevent the viewing of any TV

program that you feel may be inappropriate due to its

content.

2.Press SELECTto block the TV RATINGthat you

have selected.

3. Press EXIT to quit the menu or select TV RATING

to return to the previous menu.

TV Parental Guide Ratings Table

TV-Y All children. The themes and elements in this program are specifically designed for a very

young audience, including children from ages 2-6.

TV-Y7 Directed to older children. Themes and elements in this program may include mild

physical or comedic violence, or may frighten children under the age of 7.

TV-G General audience. It contains little or no violence, no strong language, and little or no

sexual dialogue or situations.

TV-PG Parental guidance suggested. The program may contain infrequent coarse language,

limited violence, some suggestive sexual dialogue and situations.

TV-14 Parents strongly cautioned. This program may contain sophisticated themes, intense

sexual situation, more intense violence and intensely suggestive dialogue.

TV-MA Mature audiences only. This program may contain mature themes, indecent language,

graphic violence, and explicit sexual content.

FV Fantasy Violence

V Violence

S Sexual Situation

L Adult Language

D Sexually Suggestive Dialogue

NOTE: 1. If you Block TV-14D, you will still permit TV-MA programs; If you block TV-14V, you will

automatically block TV-MAV programs, but you will still permit TV-MALS programs. This means that

the TV will block violence in TV-14 and higher (TV-MA), but not language and sex.

2. TV program ratings are dependent on the broadcaster. If the program is not rated, the TV will not

block it.

On-Screen Display

Move SEL Return

Sub Rating

Status D L S V FV

TV-Y

TV-Y7

TV-G

TV-PG

TV-14

TV-MA

Move SEL Select

Region 5

Canadian Ratings (Frn)

Canadian Ratings (Eng)

TV Ratings

Movie Ratings

Engage Lock

Change Access Code

Locks

TV Ratings

1. Use the CURSOR PAD , to select the

TV RATING category that you want to block.

Canadian Ratings (Eng)

Use CANADIAN RATINGS (ENG) to block any type of

movie and television program in Canada that you feel

might be inappropriate in its content.

2.Press SELECTto block the CANADIAN RATINGS

(ENG)that you have selected. Once rating is

selected, for example C8+, all movies and

television programs rated C8+ and higher (G,PG,

14+ and 18+) will be blocked automatically.

3. Press EXIT to quit the menu or select CANADIAN

RATINGS (ENG) to return to the previous menu.

Canadian Ratings English Table

C Programming intended for children under age 8 - Violence Guidelines; Careful attention is

paid to themes, which could threaten children’s sense of security and well-being. There will

be no realistic scenes of violence. Depictions of aggressive behaviour will be infrequent

and limited to portrayals that are clearly imaginary, comedic or unrealistic in nature. Other

Content Guidelines: There will be no offensive language, nudity or sexual content.

C8+ Programming generally considered acceptable for children 8 years and over to watch on

their own - Violence Guidelines: Violence will not be portrayed as the preferred, acceptable,

or only way to resolve conflict; or encourage children to imitate dangerous acts which they

may see on television. Any realistic depictions of violence will be infrequent, discreet, of

low intensity and will show the consequences of the acts. Other Content Guidelines: There

will be no profanity, nudity or sexual content.

G General Audience - Violence Guidelines: Will contain very little violence, either physical or

verbal or emotional. Will be sensitive to themes which could frighten a younger child, will

not depict realistic scenes of violence which minimize or gloss over the effects of violent

acts. Other Content Guidelines: There may be some inoffensive slang, no profanity and

no nudity.

PG Parental Guidance - Programming intended for a general audience but which may not be

suitable for younger children. Parents may consider some content inappropriate for

unsupervised viewing by children ages 8-13. Violence Guidelines: Depictions of conflict

and/or aggression will be limited and moderate; may include physical, fantasy, or

supernatural violence. Other Content Guidelines: May contain infrequent mild profanity, or

mildly suggestive language. Could also contain brief scenes of nudity.

14+ Programming contains themes or content which may not be suitable for viewers under the

age of 14 - Parents are strongly cautioned to exercise discretion in permitting viewing by

pre-teens and early teens. Violence Guidelines: May contain intense scenes of violence.

Could deal with mature themes and societal issues in a realistic fashion. Other Content

Guidelines: May contain scenes of nudity and/or sexual activity. There could be frequent

use of profanity.

18+ Adult - Violence Guidelines: May contain violence integral to the development of the plot,

character or theme, intended for adult audiences. Other Content Guidelines: May contain

graphic language and explicit portrayals of nudity and/or sex.

Locks

On-Screen Display

Canadian Ratings (Eng)

Locks

Move SEL Return

Status

C8+

14+

18+

Move SEL Select

Region 5

Canadian Ratings (Frn)

Canadian Ratings (Eng)

TV Ratings

Movie Ratings

Engage Lock

Change Access Code

Locks

1. Use the CURSOR PAD , to select the

CANADIAN RATINGS (ENG) category that you

want to block.

Locks

Canadian Ratings (Frn)

Use CANADIAN RATINGS (FRN) to block Canadian

French programs according to various program ratings

that you feel might be inappropriate in its content.

2. Press SELECT to block the CANADIAN RATINGS

(FRN) that you have selected. Once rating is

selected, for example 8 ANS+, all movies and

television programs rated 8 ANS+ and higher will

be blocked automatically.

3. Press EXIT to quit the menu or select CANADIAN

RATINGS (FRN) to return to the previous menu.

Canadian Ratings French Chart

G General - Programming intended for audiences of all ages. Contains no violence, or the

violence content is minimal or is depicted appropriately with humor or caricature or in an

unrealistic manner.

8 ans + 8 + General - Not recommended for young children - Programming intended for a broad

audience but contains light or occasional violence that could disturb young children.

Viewing with an adult is therefore recommended for young children (under the age of 8)

who cannot differentiate between real and imaginary portrayals.

13 ans + Programming may not be suitable for children under the age of 13 - Contains either a few

violent scenes or one or more sufficiently violent scenes to affect them. Viewing with an

adult is therefore strongly recommended for children under 13.

16 ans + Programming is not suitable for children under the age of 16 - Contains frequent scenes

of violence or intense violence.

18 ans + Programming restricted to adults - Contains constant violence or scenes of extreme

violence.

On-Screen Display

Move SEL Select

Region 5

Canadian Ratings (Frn)

Canadian Ratings (Eng)

TV Ratings

Movie Ratings

Engage Lock

Change Access Code

Locks

Canadian Ratings (Frn)

Move SEL Return

Status

8 ans +

13 ans +

16 ans +

18 ans +

Locks

1. Use the CURSOR PAD , to select the

CANADIAN RATINGS (FRN) category that you

want to block.

Alternate Ratings (Example Only) :

G General audiences. All ages admitted.

PG Parental guidance suggested. Some material may not be suitable for children.

PG-13 Parents strongly cautioned. Some material may be inappropriate for children under 13.

R Restricted. Under 17 requires accompanying parent or adult guardian.

NC-17 No one 17 and under admitted.

X Adults only

Region 5

Use Region 5 Ratings to prevent viewing of any movie or

program that you feel may be inappropriate due to its

Use the CURSOR buttons or to select the

REGION 5 category that you want to block.

Press SELECT to block the REGION 5

that you have selected. Once rating is selected, for

example PG-13, all movies rated PG-13 and higher

(R, NC-17 and X) will be blocked.

Press EXIT to quit the menu or select REGION

5 to return to the previous menu.

content. This feature will operate only for ATSC Digital

Y Adults only

In order to set the Region 5 Ratings the ATSC Digital

channel received must include Region 5 Ratings data

To see if the channel has Region 5 Ratings, press

the INFO key on the R/C. See fig. (1) for reference.



Once the TV has received Region 5 Ratings data, the

Region 5 option in the lock menu will display the data

Locks

On-Screen Display

Program Title. . . . . . . . Cable 888-001

11:30AM

11:55AMREGION 5 KDEF-DT

Multi DTVCC CF-18 ans+ 1080i 10:35 AM

MA03:11otuA

Program Title

Program Time

Source

CH ID/Input ID

Current Time

Receiving

Signal Format

Receiving

Digital Closed Caption

Receiving

Audio Language

(Digital CH)

/Receiving BTSC

(Analo g CH )

Receiving

Rating Broadcast

Alternate Ratings

Closed Caption Mode

Event Timer

INFO

Status CATEGORY NAME (1 / 10)

:[ ]

Move SEL View Block

Region 5

Locks

TV-Y

TV-Y7

12345678

ABCDEFJH

Directed to older children. Themes and elements in

this program may include mild physical or comedic

violence, or may frighten children under the age of 7.

Move SEL View Block

TV-Y

TV-Y7

12345678

ABCDEFJH

:[ ]

Status CATEGORY NAME (1 / 10)

Fig. (1)

Move SEL Select

Region 5

Canadian Ratings (Frn)

Canadian Ratings (Eng)

TV Ratings

Movie Ratings

Engage Lock

Change Access Code

Locks

Region 5

table.

Signal.

Set The Clock

Timers

Move SEL Return

Time Zone : PST

Date : Jan. 1 2007

Time : 10 : 25 AM

Move SEL Select

Set Day/Night Timer

Set Sleep Timer

Set The Clock

Timers

Not Set

0:00

-- : -- AM PST

Set Event Timer

Not Set

Select TIMERS to set your Clock, Sleep Timer, Event

Timer and Day/Night Timer.

1. Use the CURSOR buttons

 or  to highlight the

function to be adjusted.

2. Press the SELECT button to select.

Set The Clock

The Clock must be adjusted before you can use the

SET EVENT TIMER or DAY/NIGHT TIMER feature.

Use the CURSOR PAD ,,, to highlight

the chosen TIME ZONE settings.

2. Press the SELECT button to select. If you observe

daylight savings, use CURSOR PAD to highlight

DAYLIGHT SAVING CORRECTION and press the

SELECT button to select.

Use the CURSOR PAD ,,, to highlight

highlight the CURRENT TIME (hour and minute),

AM or PM, MONTH, DAY, and YEAR.

4. Use the CURSOR PAD

,  to adjust settings.

5. Press the SELECT button to set the TIME AND DATE.

6. Press EXIT to quit the menu or select SET THE CLOCK to return to the previous menu.

NOTE:1.When AUTOMATICALLY ADJUST CLOCK FOR DAYLIGHT SAVING CHANGESis checked

■

✔, the

TV will automatically calculate the clock adjustment for Daylight Saving.

2. The TV counts electrical pulses for regulating the TIMERS. When the "Main Power button" is set to OFF

and ON quickly, or the power cord is unplugged in quickly, the clock is stopped momentarily and the TIME

Timers

On-Screen Display

Setup

Timers

Channel Manager

Locks

Audio

Video

Move

SEL Select

Automatically adjust clock

for daylight savings changes.

indication will become slow.

Timers

On-Screen Display

Set Sleep Timer

Select this feature to set your SLEEP TIMER from 30

minutes to 3 hours (30 minute increments).

1. Press the CURSOR PAD

 repeatedly to set your

Timer from 0:00, 0:30, 1:00, 1:30, 2:00, 2:30 and

3:00.

Set Day/Night Timer

Select this feature to activate and set your TV’s

DAY/NIGHT PICTURE MODE automatically. This

feature is not available until the clock is set.

1. Use the CURSOR PADS to highlight SET DAY/

NIGHT TIMER settings.

2. Press the SELECT button to select the option.

3. Use the CURSOR PADS to select DAY NORMAL

MODE ON and to set it’s TIMER.

4. Use the CURSOR PADS to select DAY DYNAMIC

MODE ON and to set it’sTIMER.

5. Use the CURSOR PADS to select NIGHT MODE ON

and to set it's TIMER.

6. Press EXIT to quit the menu or select SET DAY/

NIGHT TIMER to return to the previous menu.

Move SEL Select

Set Day/Night Timer

Set Sleep Timer

Set The Clock

Timers

Not Set

0:00

10 : 25 AM PST

Set Event Timer

Not Set

Move SEL Select

Set Day/Night Timer

Set Sleep Timer 0:00

Set The Clock

Timers

Not Set

10 : 25 AM PST

Set Day/Night Timer

Timers

Move SEL Return

Day (Normal) Mode On : 06:00 AM

Day (Dynamic) Mode On : 02:00 PM

Set Event Timer Not Set

Move SEL Select

Set Day/Night Timer

Set Sleep Timer 0:30

Set The Clock

Timers

Not Set

10 : 25 AM PST

Set Event Timer Not Set

Night Mode On : 06:00 PM

NOTE: The Sleep Timer info will show for 1 minute

before the TV turns off.

Set Event Timer

Timers

Move SEL Return

❑ Event1 : -- : -- AM -



-- : -- AM Jan. 1 2007

Cable -------

❑ Event2 : -- : -- AM



-- : -- AM Jan. 1 2007

Cable -------

❑ Event3 : -- : -- AM



-- : -- AM Jan. 1 2007

Cable -------

❑ Event4 : -- : -- AM



-- : -- AM Jan. 1 2007

Cable -------

Set Event Timer

Timers

Move SEL Return

❑ Event1 : -- : -- AM -



-- : -- AM Jan. 1 2007

Cable -------

❑ Event2 : -- : -- AM



-- : -- AM Jan. 1 2007

Cable -------

❑ Event3 : -- : -- AM



-- : -- AM Jan. 1 2007

Cable -------

❑ Event4 : -- : -- AM



-- : -- AM Jan. 1 2007

Cable -------

Move SEL Select

Set Day/Night Timer

Set Sleep Timer

Set The Clock

Timers

Not Set

0:30

10 : 25 AM PST

Set Event Timer

Not Set

Timers

On-Screen Display

Set Event Timer

This function will automatically operate the Plasma TV

viewing reservation of a program. If the clock is not set,

you can not use this function and the screen at right will

appear. The message on the screen will disappear after

3 seconds, then the screen automatically goes to the

clock setup mode (see page 54).

1. Use the CURSOR PAD

,  to highlight EVENT 1,

EVENT 2, EVENT 3, EVENT 4 and then press the

SELECT button to select.

2. Use the CURSOR PAD

,  or  to highlight and

select START TIME HOUR/MINUTE.

3. Use the CURSOR PAD

,  or  to highlight and

select START TIME AM/PM.

4. Use the CURSOR PAD

,  or  to highlight and

select FINISH TIME HOUR/MINUTE.

5. Use the CURSOR PAD

,  or  to highlight and

select FINISH TIME AM/PM.

6. Use the CURSOR PAD

 to highlight the MONTH.

7. Use the CURSOR PAD

 to select a MONTH or

CURSOR PAD

 to select DAILY, WEEKLY -

SUNDAY TO MONDAY. Use the CURSOR PAD



to return to MONTH.

8. Use the CURSOR PAD

,  or  to highlight and

select the DAY of the MONTH.

9. Use the CURSOR PAD

,  or  to highlight and

select the YEAR.

10. Use the CURSOR PAD , or  or NUMBER

buttons to set the channel the TV will tune into.

11.A 앮✔in the box means the Event is enabled.

NOTE:1.When the INFObutton is pressed, the Event Timer Icon will only display the current date ON/OFFtimer.

2. The OFF TIMER will only activate if the TV was turned on by the ON TIMER, and any menu operations

(includes channels selection) were not made after this time. If you change the channel or operate menu after

the ON TIMER has been activated, the OFF TIMERwill deactivate.

CAUTION: Do not use your TV as a deterrent when away from home by using the ON and OFF

TIMERS. For safety, the TV should be turned off when you are away from home.

Please Set Clock First

Setup

On-Screen Display

Select SETUP when setting your TV up for the first

time.

1. Use the CURSOR PAD

, ,  or  to select

the sub-menu of your choice.

2. Press the SELECT button to select.

Set The Menu Options

Setup the Language and background of the Menu

OSD.

Set The Language

This feature will allow you to select any one of three

different languages for all on-screen displays.

1. Use the CURSOR PAD  or  to select the

language of your choice.

2. Press EXIT to quit menu or select SET THE MENU

OPTIONS to return to previous menu.

Setup

Move SEL Select

Reset The Software

Set The Quick Start Options

Set The Closed Captions

Set The Inputs

Set The Screen Saver

Setup The Menu Options

Setup

Audio

Video

Setup The Menu Options

Setup

Move SEL Return

Set The Language : English

Set The Menu Background : Shaded

Setup

Timers

Channel Manager

Locks

Audio

Video

Move

SEL Select

Move SEL Select

Reset The Software

Set The Quick Start Options

Set The Closed Captions

Set The Inputs

Set The Screen Saver

Setup The Menu Options

Setup

Setup The Menu Options

Setup

Move SEL Return

Set The Language : English

Set The Menu Background : Shaded

On-Screen Display

Set The Menu Background

This function allows you to choose from two menu

backgrounds.

1. Use the CURSOR PAD

 or  to highlight

SET THE MENU BACKGROUND (SHADED OR

SOLID) of your choice. Use the CURSOR PAD



or  to select shaded or solid.

2. Select SOLID for a black background (no picture

can be seen behind menu screen), select SHADED

and a light background is visible.

3. Press EXIT to quit menu or select SET THE MENU

OPTIONS to return to the previous menu.

Set The Screen Saver

Continuous on-screen displays such as video games,

stock market quotations, computer generated graphics,

and other fixed (non-moving) patterns can cause

permanent damage to the Plasma Television. Use the

SCREEN SAVER feature to hide screen burn.

1. Use CURSOR PAD  or  to highlight Screen

Saver’s Picture Orbiting and Image Power

options.

2. Use the CURSOR PAD  or  to select your

choices.

Option 1

The whole picture will shift every 2 minutes by one

pixel.

Option 2

The whole picture will shift every 10 minutes by one

pixel.

Option 3

The whole picture will shift every 20 minutes by one pixel.

Image Power

This function allows you to choose power consumption reduction based on 3 levels (min., medium and max).

Screen Wipe

If pattern mark occurs, use Screen Wipe (White Field Signal) for at least 10 minutes to refresh any damage that

may have occurred from a pattern mark. Screen Wipe can resolve pattern mark to a certain degree, if caution is

not used, permanent damage may occur.

2. Press the SELECT button to start.

Automatic Power Saving

Use this feature to turn power off automatically when a video input signal is not detected for 15 seconds.

Setup

Move SEL Select

Picture Orbiting

Automatic Power Saving

: Option 1

Image Power : Max

Screen Wipe :

Wipe

Yes

Set The Screen Saver

Setup

Move SEL Select

Reset The Software

Set The Quick Start Options

Set The Closed Captions

Set The Inputs

Set The Screen Saver

Setup The Menu Options

Setup

3. Press the EXIT button to return to normal viewing.

1. Use the CURSOR PAD

 or  to highlight Screen Wipe.

Setup

On-Screen Display

Set The Inputs

Use this feature to give a name to any of the video

inputs.

1. Press the CURSOR PAD

,  to highlight the video

inputs.

2. Press the CURSOR PAD ,  to select your

choices.

INPUT 3 Auto Link

Use this function to automatically turn the TV on and tune

to INPUT 3 when it detects a video signal to INPUT 3.

1. Use the CURSOR PAD

, ,  or  to highlight and select the AUTO LINK setting of your choice.

Auto

When AUTO is selected, the TV will turn on and switch to INPUT 3 automatically, when the INPUT 3 input

device is turned on. This is convenient when you want to watch a movie with your VCR, laserdisc player, or

DVD player.

Off

SelectOFFto disable this function.

2.Press EXITto quit menu or select AUTO LINKto return to previous menu.

NOTE: 1. Once the TV has been turned on using the AUTO LINK feature, it must be reset before AUTO LINK

is used again. To do this, turn your VCR, laserdisc, or DVD player OFF. This feature is now reset and

will turn on your TV as described above.

2.If no remote control button is pressed after the TV is turned on by AUTO LINK, the TV will

automatically turn off after three hours.

Set The Inputs

Setup

Move SEL Return

Input1 :

****

Input2 :

****

Input3 :

****

Input-Front :

****

Auto Link : Off

Move SEL Select

Reset The Software

Set The Quick Start Options

Set The Closed Captions

Set The Inputs

Set The Screen Saver

Setup The Menu Options

Setup

HDMI1 :

****

HDMI2 :

****

HDMI-Front :

****

Setup

Set The Closed Captions

Closed Captions are the dialogue, narration, and/or

sound effects of a television program or home video

which are displayed on the TV screen. Your local TV

program guide denotes these programs as or .

1. Use the CURSOR PAD , ,  and  to highlight

and select the function to change.

2. Press EXIT to quit menu or select SET THE

CLOSED CAPTIONS to return to the previous menu.

Caption Display:

ON/OFF will turn the display on or off.

AUTO will turn the display on when

Mute/Soft Mute is on.

Analog Captions:

Set CAPTIONS for Analog programs. This

function will help choose and set available

mode and channel.

Caption Mode:

CAPTIONS is for the program you are viewing.

TEXT is for additional information such as news reports or a TV program guide. This information covers

the entire screen and viewing the TV program is not possible. Text may not be available with every

program.

Channel:

1 is used for the primary language (usually English).

2 is sometimes used for a second language (may vary by region).

3 is sometimes used for a third language (may vary by region).

4 is sometimes used for a fourth language (may vary by region).

Digital Captions

Set captions for digital programs. This function

will help choose and set available language,

font, size and style of digital captions.

1. Use the CURSOR PAD

, ,  or  to highlight

and select desired DIGITAL CAPTIONS feature.

2. Press EXIT to quit menu or select SET CLOSED

CAPTION to return to the previous menu.

NOTE: 1. Some types of digital closed captions will not work with this TV.

2. Caption Display will not work when viewing a 480p, 720p, or 1080i input via the

COMPONENT: Y-P

BPR inputs.

Digital Captions Font Style are sometimes different from the Font Style of Analog Captions.

Closed Caption and Digital Captions availability and content depends on the broadcaster. Closed

Caption is available when Closed Caption icon is displayed on screen.

Digital Captions Language will not be available (grayed out) when using analog channels.

Set The Closed Captions

Setup

Move SEL Return

Caption Display : Off

Analog Mode : Captions

Channel : 1

Language : 1(Unknown)

Font : Default

H i t a c h i Size : Standard

Style : Standard

On-Screen Display

Move SEL Select

Reset The Software

Set The Quick Start Options

Set The Closed Captions

Set The Inputs

Set The Screen Saver

Setup The Menu Options

Setup

Digital

Set The Closed Captions

Setup

Move SEL Return

Caption Display : Off

Analog Mode : Captions

Channel : 1

Language : 1(Unknown)

Font : Default

H i t a c h i Size : Standard

Style : Standard

Digital

Reset The Software

Setup

Move

SEL Return

MMC Software Upgrade : Vxxxx.xxxx

Upgrade Now

before upgrading.

Reset TV Settings

No Yes

(Select "Yes" to return all settings

to the factory default after next power OFF/ON.)

On-Screen Display

Setup

Set The Quick Start Options

This feature will select QUICK START UP options. Set

this feature to ON to have the TV tune channels (both

Analog and Digital) quickly when first turning the TV on.

Set this feature to OFF to save electricity. Selecting ON

for the QUICK START UP feature will activate the TV

tuners circuits when the TV is in “standby mode” which

is commonly referred to as “off”. This will allow you to

quickly tune to channels when first turning the TV on.

Digital signals often change and this feature will monitor

any changes and prepare the television to quickly

present a picture. A small amount of electricity is used

to continually monitor signals when this feature is

selected.

Reset The Software

Set The Quick Start Options

Setup

Move SEL Select

Select ON to have the TV tune channels quickly at

1st turn on.

Select OFF to save electricity

Off On

This feature shows software information and easy

upgrade procedure. This function allows the TV software

to be upgraded by using a flash card (MMC/SD CARD).

If a future software upgrade is required for your TV,

HITACHI will notify and provide you with a flash

card. In order to receive written notification and the

flash card, please complete and return the warranty

card.

1. Insert MMC/SD CARD.

2. Press the CURSOR PAD

 or  to highlight

UPGRADE NOW.

3. Press the SELECT button to select and start

upgrading.

4. Unplug the AC power cord when the UPGRADE

is complete.

NOTE: Any power interruption during the upgrade

process will cancel the upgrade. When this

happens, repeat the upgrade procedure.

Reset TV Settings

This function allows you to Reset all TV Settings to the original factory settings on all modes during the next

power off/on.

2. Press the SELECT button or CURSOR PAD  to select Reset the Software Menu.

3. Use the CURSOR PAD  to access the Reset TV settings option.

4. Select the "YES" option to Reset ALL the TV functions during the next power on/off.

1. Use CURSOR PAD ,  to highlight functions.

NOTE: 1. If YES is selected, ALL TV MENU SETTINGS will be reset to the original factory settings on all

modes during the next power off/on.

Move SEL Select

Reset The Software

Set The Quick Start Options

Set The Closed Captions

Set The Inputs

Set The Screen Saver

Setup The Menu Options

Setup

Move SEL Select

Reset The Software

Set The Quick Start Options

Set The Closed Captions

Set The Inputs

Set The Screen Saver

Setup The Menu Options

Setup

NOTE: 1. When the Quick Start option is set to ON

the option of RESET TV SETTINGS will not

Please Insert MMC card

work with remote controller's OFF/ON.

2. When the Quick Start option has been set to ON , this option needs POWER OFF/ON operation by the

Main Power Switch.

Equipment Care and Troubleshooting

TROUBLESHOOTING

Your HITACHI Plasma Television incorporates advanced power surge protection technology designed to protect

against component or circuit damage due to external or internal voltage power surges.

IF YOUR TELEVISION SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS

PROCEDURE:

1. Press the POWER

SWITCH (ON/OFF

SWITCH) once.

2. If there is still no power,

wait 30 seconds and

press the POWER

SWITCH again.

3. If there is still no power,

unplug the power cord

from the wall. Wait 30

seconds and plug the

power cord back in.

Press the POWER

SWITCH again.

This protective technology

should provide for years of

lasting entertainment from

your HITACHI Plasma

Television.

Dust the screen and cabinet with a soft cloth.

Clean the screen with a soft cloth moistened in warm

water and dry with a soft cloth. A mild soap may be

used if the screen is extremely dirty.

Place your Plasma Television away from extreme heat,

humidity, and extremely dusty places.

Remove the plug from the wall outlet if your Plasma

Television will not be used for a long period of time, for

instance, when you go on vacation.

DO NOT

Do not clean your screen with strong cleaners, polishes

or a chemically treated cloth.

Do not place rubber or vinyl products or cellophane

tape on your Plasma Television.

Avoid repeatedly touching the screen.

Do not subject the remote control to shocks such as

dropping it on the floor, etc. This may cause damage to

the precision parts.

Avoid placing the remote control in a high humidity

place or getting it wet. Do not leave it on or near a

heater. Excessive heat or moisture may cause the unit

to fail.

When the batteries run down, remote control operation

will become erratic or become unresponsive. Replace

the old batteries with two new “AA” size batteries. Do

not use an old battery with a new battery.

Exposing the screen to direct sunlight for a long period

of time or heat may cause damage to the plasma

screen.

SYMPTOMS

CHECK THESE ITEMS AND

TRY THESE ADJUSTMENTS

No Picture, no sound

Sound OK, picture poor

Picture OK, sound poor

Picture blurred

Lines or streaks in picture

Poor reception on some channels

Picture rolls vertically

No color

Poor color

쏹

쏹쏹

쏹쏹쏹쏹

쏹

쏹쏹

쏹쏹쏹쏹

쏹

쏹쏹쏹쏹

쏹쏹

쏹쏹쏹쏹

쏹

쏹쏹쏹쏹

쏹

쏹쏹쏹쏹

쏹

쏹쏹쏹쏹

쏹

Be sure external connectio

n is corre

Be sure

power cord is plugged in

Be sure TV is switched''ON"

Try another channel (station trouble)

Check antenna connections (back of TV)

Check antenn

a for broken lead-in

wire

Check for lo

cal interfe

rence

Check outside

antenna

Adjust Contrast control

Adjust Brightn

ess control

Adjust Color control

Adjust Tint control

Adjust Volume control

Useful Information

Reception Problems

IGNITION NOISE:

Black spots or horizontal streaks may appear, picture may flutter or drift.

Usually caused by interference from automobile ignition systems, neon lamps,

electrical drills, and other electrical appliances.

GHOSTS:

Ghosts are caused by the television signal following two paths. One is the

direct path and the other is reflected from tall buildings, hills or some other

objects. Changing the direction or position of the antenna may improve

reception. Ghosting may also be caused by defects in the antenna system such

as unshielded leads or connecting several sets to the same antenna without

using multiple antenna couplers.

SNOW:

If your receiver is located in the fringe area of a television station where the

signal is weak, your picture may be marred by the appearance of small dots.

When the signal is extremely weak, it may be necessary to install a special

antenna to improve the picture.

RADIO FREQUENCY INTERFERENCE:

The interference produces moving ripples or diagonal streaks, and in some

cases, causes loss of contrast in the picture.

• PREVENTION OF AN OBSTACLE TO RADIO RECEIVERS

This television has been designed pursuant to the FCC class B Rules. This is to prevent a problem to Radio

receivers. If this television causes a problem to Radio receivers, then take the following steps:

- Keep the television away from Radio.

- Adjust Radio antennas in order for the television not to receive interference.

- The antenna cable of Radio should be kept away from the television.

- Use a coaxial cable for antenna.

You can check if this television influences Radio receivers by turning off all other equipment other than the television.

If you find a problem receiving Radio when using the television, check the instructions mentioned above.

BLOCK NOISE (DIGITAL INPUT):

Fuzzy blocks may appear in some area or the whole area of the screen. This is

usually caused by interference from automobile ignition systems, neon lamps,

electrical drills, ghosting of the image and weak signals.

BLACK SCREEN:

When using an antenna, weak signals will display a black screen. It may be

necessary to upgrade your antenna.

NOTE: The TV set can generate sound distortion in external devices such as a radio. Please separate radio

equipment from the TV set to a considerable distance.

Useful Information

Troubleshooting

No. Items Notes

Buzzing sound from Plasma

display panel.

A buzzing sound may be heard when the plasma television is turned on in a very quiet

room. This is due to the plasma panel drive circuit when it is functioning. The buzzing

sound is normal and is not a malfunction.

Infrared interference

Some infrared rays are emitted from the plasma television panel that might affect the

operation of other infrared controlling equipment.

3 Bright and dark spots

High precision technology is used to manufacture the plasma television. But there

maybe points that do not illuminate, points that are too bright, and points with color

different from that of the periphery. Please note that this is not a malfunction.

Picture Image

In some cases, residual images may remain after the short term display of still images

when the picture changes.

Display panel surface

temperature is too high.

The plasma display panel display images by means of electrical discharges inside the

panel. This may cause the temperature of the panel surface to increase. Please note that

this is not a malfunction.

Plasma Surface

A reinforced glass filter is installed over the plasma panel surface. A strong impact to

the front panel risk a danger of glass breakage.

Transportation

Please transport the plasma television in it's packing box and placed in an upright

position. Do not transport the plasma television in a horizontal position. This increases

the posibility of panel breakage and pixel failure.

Granular spots

When a screen is seen at point-blank range, a random fine grain may be visible in the

dark areas of the picture.

High temperature

environment

High temperature affect the electric discharge/luminescence characteristic of the PDP

panel. Do not place the plasma television in high temperature environments.

10 Operation Operating altitude: 700 to 1,114hPa (9,676ft to -2,484ft). Operating temperature: 41°F

to 95°F.

11 Storage

Storage altitude: 300 to 1,114hPa (31,912ft to -2,484ft). Storage temperature: 5°F to

140°F

12 Power ON or OFF

Repeatedly turning the plasma television Power ON and OFF at short intervals may

result in failure of the television.

The on-screen motion of an actor's lips or other moving object may not be in sync with

the associated audio heard from the TV's speakers. This is caused by timing differences

in the broadcast signal or DVD content and is not caused by a defect in the television.

13 Lip sync

There's a few seconds response delay on the control buttons (Control panel or R/C) after

the TV is turned ON; due to TV start-up routine. Please note that this is not a TV malfunction.

Response Delay

Control Buttons

1. Plasma Television Troubleshooting

Useful Information

test-bleed 3/3/06 10:19 AM Page 85

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not

installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician for help.

FCC Information

This device complies with part15 of the FCC Rules.Operation is subject to the following two conditions :

(1) This device may not cause harmful interference and (2) This device must accept any interference

received, including interference that may cause undesired operation.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not

expressly approved by Hitachi America ,Ltd. Home Electronics Division may void the user’s authority to

Cables

Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to

maintain compliance with FCC Rules and Regulations.

Any cables that are supplied with the system must be replaced with identical cables in order to assure

compliance with FCC rules. Order Hitachi spares as replacement cables.

Useful Info

AGENCY REGULATORY INFORMATION

operate the equipment.

This Plasma Television receiver will display television closed captioning, ( or ), in accordance with

paragraph 15.119 and 15.122 of the FCC rules.

Note

Cable Compatible Television Apparatus- Tèlèvision câblocompatible, Canada.

INDUSTRY CANADA AGENCY REGULATORY INFORMATION

Useful Information

test-bleed 3/3/06 10:19 AM Page 86

All specifications, weights, and dimensions are subject to change without

prior notice. Please access www.hitachi.com/tv for detailed specifications

and dimensions for custom installations.

UltraVision Digital is a registered trademark of Hitachi Home Electronics

(America), Inc.

• New Easy-to-Use On-Screen Menu Control (3

Language)

Region 5 (Downloadable V-Chip)

Preprogrammed Remote Control

Power Management: ON/OFF via signal detection

Picture Enhancement

Input Signal Identification

HDMI (High Definition Multimedia Interface)(High

Bandwidth Digital Content Protection V1.1

Compatible)

Closed Captions (Analog and Digital)

Sleep and Event Timer

Technology

1024 x 1080 Display Resolution (42")

1280 x 1080 Display Resolution (50")

1280 x 1080 Display Resolution (55")

ALiS (Alternate Lighting of Surfaces Technology)

High-Contrast Pure-Color Glass Shield

Wide Viewing Angle: More than 160°

•

Color Temperature Presets: High, Standard,

and Medium

•

Multiple Screen Fill Modes

(4:3 Standard/4:3 Expanded/4:3 Zoom 1/

4:3 Zoom 2/16:9 Standard1/Standard2/16:9 Zoom)

4MB 10-bit 3D Y/C Comb Filter

Power Consumption

- Refer to rear panel at the back of the Plasma

Monitor

Antenna input impedance . . . . . . . . . . . . . . . .75 Ohm

Channel coverage . . . . . . . . . . . . . . . . . . . . . . . 203ch.

VHF-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ~ 13

UHF-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ~ 69

CATV Mid Band . . . . . . . . . . . . . . . . . . . . . . A-5 ~ A-1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-I

Super Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-W

Hyper Band . . . . . . . . . . . . . . . . . . . . . . . W+1 - W+28

Ultra Band . . . . . . . . . . . . . . . . . . . . . . . W+29 - W+94

Video . . . . . . . . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm

S-Video

Luminance (Y) . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm

Chrominance (C) . . . . . . . . . . . . . 0.286Vp-p, 75 Ohm

Component Video

Luminance (Y) . . . . . . . . . . . . . . . . . 1.0Vp-p, 75 Ohm

Chrominance (P

) . . . . . . . . . . . 0.7Vp-p, 75 Ohm

Audio input Impedance . . . . . . . . . . . . . . . . 270k Ohm

Average input level . . . . . . . . . . . . . . . . . . . 470mVrms

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (19 PIN)

Outputs:

Video 1.0Vp-p. 75 Ohm

Audio . . . . . . . . . . . . . . . . . . . . . . .470mVrms, 1k Ohm

Optical Out (Digital Audio) . . . . . .1 Optical Connector

Audio:

MTS Stereo/SAP

Bass Boost

20W

Soft Mute (50%)

Supplied Accessories:

Remote Control

Batteries (AA)

6' AC Power cord cable

Table Top Stand

Optional Accessories:

For U.S. Models: Please access our website:

www.hitachi.us/tv

INPUTS/OUTPUTS

Wideband Component Y, PB,PR . . . . . . . . . . . . . . . . 2

Composite Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

S-Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Antenna (RF)Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Monitor Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Optical Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Upgrade Card/Photo Input Slot . . . . . . . . . . . . . . . . . 1

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

RS232C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SPECIFICATIONS

Pixel Pitch . . . . 0.900(horiz.) x 0.485(vert.) mm.(42")

. . . . . . . . . . . . .0.864(horiz.) x 0.580(vert.) mm.(50")

FCC class: . . . . . . . . . . . . B for Consumer Use

•

• Power Requirements:. . . . . . . . 108-132VAC, 60Hz

Screen mode availability varies by input format

• Picture Modes :Day(Normal), Day(Dynamic) and Night

•

PowerInput. . . . . . . . . . . . . . . . . . . . .AC120V,60Hz

Inputs:

Features and Specifications

•

Features:

Television System . . . . . . . . . . . . . . . NTSC Standard

ATSC Standard (8 VSB, 64-QAM, 256-QAM)

•

Surround Sound

HDTV Televisions display HDTV only when an HDTV source is available.

HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of HDMI Licensing

LLC.

*Manufactured under license from Dolby Laboratories. “Dolby” and the

double-D symbol are trademarks of Dolby Laboratories.

㪚㪦㪧㪰㪩㪠㪞㪟㪫㩷㪺㩷㪈㪐㪐㪐㪄㪉㪇㪇㪍㩷㪤㪦㪥㪫㪘㪭㪠㪪㪫㪘㩷㪪㪦㪝㪫㪮㪘㪩㪜㪃㩷㪠㪥㪚㪅㩷㪘㪣㪣㩷㪩㪠㪞㪟㪫㪪㩷㪩㪜㪪㪜㪩㪭㪜㪛㪅

•

Video:

. . . . . . . . . . . . .0.960(horiz.) x 0.640(vert.) mm.(55")

Useful Information

•

• SD/MMC Memory Card Photo Input capability

test-bleed 3/3/06 10:19 AM Page 87

Set Dimensions

Useful Information

Units

Inches

Inches 42 2-3/4 2-3/4 30-21/32 28-1/16

21-31/32 17-31/32 15-11/32 36-7/16 20-23/32 4-23/32 3-9/16 1-1/8 15-9/32 8-19/32 24-13/16 8-19/32 9-7/8 12-1/8 6-1/16

1067.00 70.5 70.5 779

.15 713.00 558.32

456

.15 390.00 926 526.60 119.50 90.80 28.70 388.38 218.50 630.00 218.50 251.00

308.00 154.00

42 Inch Models (Includes Table Top Stand) Weight (lbs./kg): 80.4/36.5

Rear View, Use as Reference for Wall Mount Bracket

Set Dimensions

Useful Information

Units

Inches

Inches 48-13/16 2-9/16 2-9/16 34-11/16 32-5/16

27-17/32 19-29/32 17-17/32 43-23/32 24-13/16 5-1/2 3-25/32 1-1/4 16-5/8 12 24-13/16 12 11-3/4 12-1/8 8-7/16

1240 65.00 65.00 880.85 820.50 699.12

505.85 445.5 1110.00 630.00 127.50 96.00 31.50 422.08 305.00 630.00 305.00 298.00

308.00 214.50

50 Inch Models (Includes Table Top Stand) Weight (lbs./kg): 116.7/53

Rear View, Use as Reference for Wall Mount Bracket

test-bleed 3/3/06 10:19 AM Page 87

Useful Information

Set Dimensions

Units

Inches

Inches 55-1/2 3-15/32 3-15/32 35-5/8 19-3/16

48-19/32 27-1/4 5-1/32 3-25/32 1-1/4 15-11/32 24-13/16 15-11/32 4-15/16 10-1/8 12-1/8

1410.00 88.00 88.00 904.50 485.50 1234.00

692.00 127.50 96.00 31.50 390.00 630.00 390.00 125.00 257 308

55 Inch Models (Not Includes Table Top Stand) Weight (lbs./kg): TBD

Rear View, Use as Reference for Wall Mount Bracket

Hitachi

HITACHI AMERICA, LTD.

HOME ELECTRONICS DIVISION

HITACHI has made every effort to assure you hours of

trouble free operation from your unit. However, should

you require service, a network of HITACHI Authorized

Service Facilities has been established in all 50 states

and Puerto Rico. Each facility will provide you with

convenient and expedient assistance. Our service

hotline operator will direct you to the HITACHI

Authorized Service Facility nearest you. Just present

proof of purchase and/or delivery receipts to the

Hitachi Authorized Service Facility, and service will be

rendered in accordance with the terms of the limited

warranty as stated on your warranty card or operating

guide.

Should you have any questions regarding warranty,

service, operation, or technical assistance, please

contact:

Hitachi America, LTD.

Home Electronics Division

900 Hitachi Way

Chula Vista, CA 91914-3556

HITACHI CANADA, LTD.

Should you have any questions regarding warranty,

service, operation, or technical assistance, please

contact:

In Canada: 1-800-HITACHI (1-800-448-2244)

Monday – Friday (EST).........................9:00am – 7:00pm

Saturday (EST) .....................................9:00am – 5:00pm

Look for your French Manual on the outside of the

box. If the manual is missing, call 1-800-HITACHI

(1-800-448-2244) for a copy.

Pour de plus amples renseignements sur le service

durant la période couverte par la garantie, sur le

fonctionnement ou pour de l’assistance technique

communiquez avec:

Au Canada: 1-800-HITACHI (1-800-448-2244)

Lundi - Vendredi L’EST ........................9:00am – 7:00pm

Samedi L’EST.......................................9:00am – 5:00pm

La version français de votre manual se trouve a

l’exterieur de la boîte. Si le manuel est manquant,

coposez le 1-800-HITACHI (1-800-448-2244) pour

obenir votre copie.

HITACHI CANADA, LTD.

1-2495 Meadowpine Blvd.

Mississauga, Ontario L5N 6C3

Service Hotline

To locate an authorized HITACHI

service facility in the continental

U.S.A. and Canada,

DIAL TOLL FREE

7 days a week, 24 hours a day

1-800-HITACHI

(1-800-448-2244)

Useful Information

test-bleed 3/3/06 10:19 AM Page 87

Useful Information

쐃

쐇

쐋

쐃

쐇

Look on the right side of the TV.

Locate the LABEL where it shows the information

related to MODEL NAME and SERIAL #.

HITACHI Service Department will require this

information in order to give you the proper

support regarding your questions.

When you call HITACHI SERVICE HOTLINE they will require some information related to the

TV MODEL NAME and SERIAL # in order to give you the proper support. This information is

located on the back of the TV and also on the RIGHT SIDE of your TV set. Please follow the

next steps to find this information and then provide to SERVICE.

Service Information

Notes

Service Hotline

test-bleed 3/3/06 10:18 AM Page 1

TELEVISOR DE PLASMA

Guía de funcionamiento para P42T501,

Como miembro de Energy Star,

Hitachi, Ltd. ha determinado

que este producto cumple con las

recomendaciones de Energy Star

de eficiencia de energía.

P50T501 y P55T551

INSTRUCCIONES IMPORTANTES DE SEGURIDAD............................................................ 74-75

USO POR PRIMERA VEZ ..................................................................................................... 76-94

EL CONTROL REMOTO ........................................................................................................ 95-110

MENU EN PANTALLA ....................................................................................................... 111-133

INFORMACIÓN ÚTIL .......................................................................................................134-143

test-bleed 3/3/06 10:18 AM Page 2

SOBRE SU TELEVISOR DE PLASMA HITACHI

Nuestra reputación se ha formado en base a la calidad,

desempeño y facilidad de servicio de los televisores de

plasma HITACHI.

La seguridad está en primer lugar en nuestra mente al

diseñar estas unidades. Para ayudarlo a operar estos

productos en forma apropiada, esta sección ilustra datos

de seguridad que serán de beneficio para usted. Léalos

cuidadosamente y aplique los conocimientos adquiridos

para operar con propiedad su televisor de plasma

HITACHI.

Complete su tarjeta de garantía y envíela por correo a

HITACHI. Esto le permitirá a HITACHI notificarlo

rápidamente en el caso improbable de que se descubra

un problema de seguridad en el modelo de su televisor.

Siga todas las advertencias e instrucciones marcadas

en este televisor de plasma.

El símbolo del rayo dentro de un triángulo

equilátero tiene por finalidad alertar al usuario

acerca de la presencia de voltaje peligroso (sin

aislamiento) en el interior del producto, que

puede tener la intensidad suficiente como para

considerar un riesgo de descarga eléctrica.

El signo de exclamación dentro de un triángulo

equilátero tiene por finalidad alertar al usuario

de instrucciones importantes de operación y

mantenimiento (servicio) en la literatura que

acompaña a este aparato.

LEA ANTES DE HACER FUNCIONAR EL EQUIPO

Siga todas las advertencias e instrucciones indicadas en

este televisor de plasma.

1. Lea estas instrucciones.

2. Conserve las instrucciones.

3. Tomar en cuenta todos los avisos.

4. Siga todas las instrucciones.

5. No utilice este aparato cerca del agua.

6. Limpie el equipo con un paño seco.

7. No bloquee las rendijas de ventilación. Instale el

equipo según las instrucciones del fabricante.

8. No lo instale cerca de fuentes de calor, como

radiadores, registros de calor, hornos o demás

aparatos (incluidos amplificadores) que produzcan

calor.

9. No altere la función de seguridad de la clavija de tipo

conexión a tierra. La clavija de tipo conexión a tierra

tiene dos terminales y una tercera terminal de

conexión a tierra. La tercera terminal se incluye para

su seguridad. Si la clavija suministrada no encaja en

la toma, póngase en contacto con un electricista para

que cambie el receptáculo (enchufe).

Instrucciones Importantes de Seguridad

10. Proteja el cable de alimentación para que no se pise ni

esté retorcido, especialmente en las clavijas, los

receptáculos y el punto por el que sale del aparato.

11. Utilice únicamente los accesorios especificados por el

fabricante.

12. Utilice únicamente el carro, mueble, tripie,

soporte o mesa especificado por el

fabricante o de venta con el aparato. Si

utiliza un carro, tenga cuidado al mover el

aparato para evitar que se caiga y provoque daños

personales.

13. Desconecte el equipo durante tormentas eléctricas o

cuando no lo vaya a utilizar durante periodos

prolongados.

14. Para tareas de mantenimiento, diríjase a personal

calificado. Será necesario recurrir a tareas de

mantenimiento si el aparato sufre daños de cualquier

tipo, si el cable de alimentación o la clavija están

dañados, si ha caído líquido u otros objetos en el

aparato o si éste ha sido expuesto a la lluvia o

humedad, si no funciona con normalidad o se ha

caído.

15. Los televisores están diseñados para cumplir con los

estándares de seguridad recomendados para

inclinación y estabilidad. No aplique fuerza excesiva a

la parte superior o frontal de gabinete que pudiera

hacer que el televisor se caiga causando daño del

producto y/o daño personal.

16. Siga las instrucciones de montaje en la pared, estante

o techo según lo recomendado por el fabricante.

17. Una antena exterior no deberá ser instalada en la

cercanía de líneas de alimentación externas ni de

otros circuitos de iluminación eléctrica.

18. Si se conecta una antena externa ó sistema de cable

a la unidad, cerciórese de que el sistema de antena ó

cable está conectado a tierra para darle protección

contra sobretensión y acumulación de carga estática.

La Sección 810 del Código Nacional de Electricidad,

ANSI/NFPA 70-1984, proporciona información con

respecto a como poner a tierra el mástil apropiadamente

y la estructura de sostenimiento, al poner a tierra el

alambre de entrada a una unidad de descarga de la

antena, tamaño de los conectores para poner a tierra,

locacalidad de la unidad de descarga de antena,

conexión de los electrodos a tierra y los requisitos

para el electrodo que pone a tierra.

Nota para el instalador del sistema CATV. Este

recordatorio se provee para llamar la atención del

instalador de sistema CATV hacia el Artículo 820-44 de la

NEC que brinda guías para una puesta a tierra apropiada

y en particular, especifica que la tierra del cable debe

conectarse al sistema de tierra del edificio, tan próximo a

la entrada de cable como sea más práctico.

PRECAUCIÓN

RIESGO DE DESCARGA

CTRICA NO ABRIR

AVISO: PARA REDUCIR EL RIESGO DE DESCARGA ELECTRICA, NO

RETIRE LA CUBIERTA NI EL PANEL POSTERIOR. EN EL INTERIOR

DEL APARATO NO EXISTEN PARTES QUE DEBAN SER REPARA-

DAS POR EL USUARIO. SOLICITE SERVICIO O REPARACIÓN

A PERSONAL CALIFICADO.

NEC - CODIGO NACIONAL DE ELECTRICIDAD

ALAMBRE DE ENTRADA DE LA ANTENA

ABRAZADERA

DE TIERRA

EQUIPO DE SERVICIO ELECTRICO

ABRAZADERAS DE TIERRA

UNIDAD DE DESCARGA DE LA ANTENA

(NEC, SECCION 810-20)

CONDUCTORES DE PUESTA A TIERRA

(NEC, SECCION 810-21)

SERVICIO DE ALIMENTACION DE SISTEMA

ELECTRODO DE PUESTA A TIERRA

(NEC ART 250, PARTE H)

PUNTOS DE SEGURIDAD QUE USTED DEBE SABER

test-bleed 3/3/06 10:18 AM Page 3

Visión pública de material con derechos de autor

La visión pública de programas transmitidos por

estaciones de televisión o compañías de cable, así como

programas de otras fuentes, puede requerir autorización

previa del difusor o propietario del material de programa

de video.

Este producto incorpora la tecnología de protección de

derechos de autor, que está protegida por demandas de

métodos de ciertas patentes de EE.UU. y otros derechos

de propiedad intelectual pertenecientes a Macrovision

Corporation y otros propietarios de derechos. El uso de la

tecnología de protección con derechos de autor debe ser

autorizada por Macrovision Corporation, y está autorizada

sólo para uso en el hogar y otros usos limitados al

consumidor a menos que Macrovision autorice lo

contrario. Está prohibida la ingeniería inversa o el

desmontaje.

Nota

Este televisor digital es capaz de recibir programación

básica análoga, básica digital de televisión por cable

, mediante la conexión directa a un sistema de

cable que provea tal programación. Ciertos

servicios de cable digital interactivos tales como

video-on -demand (sobre pedido), una guía de

programas mejorada del operador de cable y servicios de

transmisión de datos por televisión pueden requerir el uso

de un decodificador. Para mayor información llame a su

compañía de cable local.

Nota

• No existen partes remplazables por el usuario dentro

del televisor de plasma.

• Los números de serie y modelo se indican en la parte

posterior y el lado derecho del televisor de plasma.

Instrucciones Importantes de Seguridad

Fuente de energía

Este televisor de plasma esta diseñado para operar con

corriente CA, 120 voltios 60 Hz. Inserte el cable de

electricidad en un tomacorriente de 120 voltios a 60 Hz.

El cable se utiliza como dispositivo de desconexión y

continua estando disponible.

Para impedir descarga eléctrica, no utilice la clavija

(polarizada) del televisor de plasma con una extensión,

receptáculo u otro enchufe a menos que los terminales y

el terminal de tierra puedan insertarse completamente

para evitar que la terminal este expuesta.

Nunca conecte el televisor de plasma a 50 Hz, corriente

directa o cualquier otro voltaje que no sea el especificado.

Precaución

Nunca quite la tapa trasera del televisor de

plasma ya que puede exponerlo a voltajes

muy altos y a otros peligros. Si el televisor no

funciona en forma apropiada, desenchufe el

televisor de plasma y llame a su distribuidor

o centro de servicio autorizado.

Precaución

Ajuste solamente los controles que se incluyen en las

instrucciones, ya que cambios inapropiados o

modificaciones que no estén expresamente aprobadas

por HITACHI podrían anular la garantía.

Advertencia

• Para reducir el riesgo de fuego o shock eléctrico, no

exponga el aparato a lluvia o humedad.

• El televisor de plasma no se debe exponer a filtrado o

salpicado de líquidos y a objetos con líquidos, tales

como floreros que no se deben colocar sobre el

televisor.

• Este aparato se debe conectar a la red de electricidad

con una conexión de protección a tierra.

Prevención de daños a la pantalla

La proyección continua en pantalla de imágenes tales

como videojuegos, Mercado bursatil, gráficos generados

por computadora, y otros patrones fijos (sin movimiento)

pueden quedar impresos en forma permanente en la

pantalla de su televisor. Tales "DAÑOS A LA PANTALLA"

constituyen un mal uso y NO ESTÁN CUBIERTOS por su

Garantía de Fábrica Hitachi.

Aviso sobre el Plomo

Este producto contiene plomo. Deseche este producto de

acuerdo a las leyes ambientales aplicables. Para

información sobre reciclado y desecho del producto,

contacte su agencia gubernamental local o en www.eRe-

cycle.org (en California) a Electronic Industries Alliance

en www.eiae.org (en EE.UU.) o a Electronic Product

Stewardship Canada en www.epsc.ca (en Canadá).

PARA MAYOR INFORMACIÓN, LLAME AL 1-800-HITACHI

Si se dejan imágenes fijas en la pantalla por más de 2.5

minutos, la función de protección iniciará automáticamente

de manera que el contraste se reduce para minimizar la

retención de imagen en la pantalla de plasma.

Por favor note que esto no es un defecto sino una medida

para minimizar la retención de imagen.

El contraste original se restablecerá después de desplegar

imágenes en movimiento por aproximadamente 6 minutos.

El contraste original puede ser restablecido rápidamente

apagando y encendiendo el televisor con el control

remoto o con el interruptor principal del televisor.

test-bleed 3/3/06 10:18 AM Page 4

Uso por primera vez

Cable de energía

Control Remoto

tipo “AA” 1.5V

BASE

(50" incluida)

Para modelos de U.S.A. :

Para accesorios opcionales, visitar nuestro

sitio de internet : www.hitachi.us/tv

Base

(42” incluida)

Dos baterías

Nota: Visitar nuestro

sitio de internet para

accesorios opcionales.

쐃 Control Remoto CLU-4371A

(Part No. HL02401).

쐇 Dos baterias tipo "AA" , 1.5V .

쐋 Base giratoria (UX27662 modelos 42")

쐏 Cable de energía (No. Parte EV01841).

쐃

쐋

쐇

쐏

Abrir la cubierta de las baterias del control remot

presionando la pestaña para quitar la cubierta.

Colocar dos baterias tipo “AA” para el control remoto

.Alr

emplazar las baterias, empujar hacia los

resortes y luego sacarlas.

3. Coincidir las marcas de las baterias (+) y (-) con las marcas

del compartimiento.

4. Insertar la parte inferior de la batería, el lado (-) neg, en el compar-

timiento primero , luego empujar hacia los resortes e insertar

la parte superior de la batería

, el lado (+) pos, en su lugar. No

forzar la batería dentro del compartimiento.

5. Colocar de nuevo la cubierta.

Vista Posterior (Control Remot

)

Presionar la pestaña para quitar la cubierta

INSTALACIÓN Y REMPLAZO DE LAS BATERIAS DEL CONTROL REMOTO

(UX27282 modelo 50" ).

쐋

Asegurarse de que tiene los siguientes accesorios antes de desechar el material de empaque.

Accesorios

PRECAUCIÓN: 1. El montaje en el techo no es recomendable. Montar el panel en el techo no provee

la adecuada ventilación a lo electronico ó el apropiado suporte al panel frontal de

vidrio. Este televisor de plasma está deseñado para una inclinación máxima de 45°

en vertical.

2. Esta base es solo para los modelos P42T501 y P50T501. El uso con otros

aparatos no indicados puede causar inestabilidad ocasionando daños personales.

PRECAUCIÓN : No coloque la baterias con la polaridad ‘+’ y ‘-’ invertidas esto puede causar que

las baterias se derramen dentro del compartimiento.

3. La base para la pared para los modelos 50" y 42" es WM07S y para los modelos

55" es WM07L. Favor de ver las páginas 79-80 para información importante

relacionada con la base de la pared. La base es un accesorio opcional (No está Incluida).

4 in.

10 cm

4 in.

10 cm

42"

50"

4 in.

10 cm

55"

test-bleed 3/3/06 10:18 AM Page 5

Uso por primera vez

42” 50”

30 cm (12 pulg.)

10 cm (4 pulg.)

ANTENA

A menos que su televisor de plasma esté conectado a

un sistema de televisión por cable o a un sistema de

antena externa, se recomienda una buena antena de

televisión color para mejor rendimiento. Sin embargo, si

se encuentra en un área con señal excepcionalmente

buena sin interferencia y sin fantasmas en la imagen,

una antena interior puede ser suficiente.

UBICACIÓN

Seleccione un área donde la iluminación interior o la luz

solar no se diriján directamente sobre la pantalla.

También asegúrese de que la ubicación seleccionada

permite un flujo libre de aire hacia y desde la tapa

posterior del equipo. Para evitar el aumento de

temperatura interna, mantenga un espacio de 4

pulgadas (10 cm) desde los lados y la parte posterior del

televisor, y 30 cm (12 pulgadas) desde la parte superior

del televisor a la pared. Para evitar deformaciones

del gabinete, cambios en el color del gabinete y mayor

oportunidad de falla en el equipo, no coloque el televisor

donde las temperaturas puedan volverse excesivamente

cálidas por ejemplo, a la luz solar o cerca de un calefactor,

etc.

55”

Asegurando a una mesa ó mueble

1. Usar dos tornillos de madera para sujetar el set a

la mesa usando los agujeros en la parte posterior

de la base del Televisor como se muestra.

2. Usando tornillos de madera comercial, asegure el

set firmemente a la mesa o mueble.

Asegurando a una pared

* Favor de ajustar la longitud del cable para evitar

que la TV toque la pared al girarla.

Tornillo de madera

dos posiciones

Cable

Cómo colocar su nuevo televisor de plasma HITACHI

Como tomar medidas para evitar que el televisor de plasma se incline e impedir posibles daños, es importante

montar la unidad en una superficie estable y lisa.

NOTAS: 1. No bloquee los ranuras de ventilación del

televisor de plasma. El bloqueo de agujeros

de ventilación podría causar fuego o defectos.

2. En caso de un síntoma anormal, desenchufe

el cable de CA.

3. Si compró el soporte de montaje a la pared,

solicite un instalador profesional.

No lo instale por su cuenta.

4. Instale la unidad en un área apropiada donde

no se exponga a nadie al peligro de golpearse

(por ejemplo, manos cabeza o cara) contra el

borde de la unidad y causar daño personal.

1. Mantenga el televisor de plasma a 4 pulgadas (10 cm)

de la pared excepto cuando lo monta usando un

soporte de montaje a la pared.

2. Asegure el televisor a la pared como se muestra

en la fig.

Precaución al mover la unidad principal

Como este producto es pesado, para moverlo, se requieren

dos personas para transportarlo con seguridad. Cada vez

que se mueva la unidad debe levantarse hacia adelante

usando la parte superior y la base a ambos lados del

televisor para lograr estabilidad. Cuando mueva el televisor,

levante de las agarraderas que sostienen la estructura

luego tomar de la parte superior como se muestra :

NOTA: La base para el modelo P55T501 no está

incluida (Opcional).

ANGULO DE ROTACIÓN

El máximo angulo de rotación es 30° (Izq. y Der.). No

colocar objetos en el paso del monitor al usar la

base giratoria.

C D

10.59 in. 13.93 in.

27 cm 36 cm

15 in. 16. 85 in.

38. 1 cm 42.8 cm

42"

50"

15 in. 16. 85 in.

38. 1 cm 42.8 cm

55"

test-bleed 3/3/06 10:19 AM Page 88











Pasar el cable de AC através del sujetador #1 y

Los cables de señal y el cable de AC pueden ser

sujetados con el sujetador #2.

Dependiendo del modelo 42, 50 ó 55 pulg., el

sujetador de plástico puede ser de diferente

forma. El sujetador #2 será incluido en la bolsa de

Cable de AC

Sujetador #2: Usar para sujetar el cable de AC

con el resto de cables usados en

Sujetador #1 : Pasar el cable de AC através de este

sujetador primero; luego jalar el extremo

para sujetar el cable al televisor.

INSTRUCCIÓN DE COMO COLOCAR EL CABLE DE AC

El cable de AC que viene incluido en su nuevo Televisor de Plasma necesita ser ensamblado correcta-

mente para evitar que se desconecte al girar el Televisor con su base. En el Televisor

existen 2 sujetadores de plástico localizados en la parte posterior del Televisor para sujetar el cable

Cómo colocar su nuevo televisor de plasma Hitachi

conectarlo al televisor. Jalar el extremo del sujetador

para sujetar el cable de AC con el televisor.

de AC. Favor de seguir las siguientes intrucciones.

el Televisor. Para los modelos de

accesorios solo para los modelos de 50 pulg.

50 pulg. insertar este Sujetador

en el agujero de en medio de la base

de metal.

Uso por primera vez

test-bleed 3/3/06 10:19 AM Page 88

Cómo colocar su nuevo televisor de plasma Hitachi

NOTA: Use la base para pared (WALL MOUNT) para el Televisor de Plasma de acuerdo al tamaño.

Visite nuestro sitio de internet: www.hitachi.us/tv para accesorios de su Televisor.

CONFIGURACIÓN PARA MONTAJE EN LA PARED EN MODELOS 50" y 55"

PASO (1) :

Localizar el metal de la BASE en la parte posterior del televisor. Este metal es usado para sostener el televisor y la

base; se tienen que quitar 4 tornillos de la BASE para separar el televisor de la base.

METAL de la BASE

PASO (2):

Quitar los 4 tornillos de la BASE de metal del Televisor , ahora la BASE puede ser separada del Televisor.

Para dimensiones del ensamble en la PARED referirse a la página 140 y 141.

METAL de la BASE

4 Tornillos

BASE del TELEVISOR

PRECAUCIÓN - Este televisor de Plasma solo puede usar la base para la pared WM07S de Hitachi. Al usar otra

base puede causar inestabilidad en el televisor provocando posibles heridas personales.

PRECAUCIÓN - Este televisor de Plasma solo puede usar la base para la pared WM07L de Hitachi. Al usar otra

base puede causar inestabilidad en el televisor provocando posibles heridas personales.

Para el Modelo P50T5

Para el Modelo P55T5

Uso por primera vez

test-bleed 3/3/06 10:18 AM Page 6

Cómo colocar su nuevo televisor de plasma HITACHI

CONFIGURACIÓN PARA MONTAJE EN LA PARED EN MODELO 42"

PASO (1) :

Localizar el metal de la BASE en la parte posterior del televisor. Este metal es usado para sostener el televisor y la

base; se tienen que quitar 6 tornillos de la BASE para separar el televisor de la base.

METAL de la BASE

PASO (2):

Quitar los 2 tornillos del metal de la BASE del Televisor , luego quitar los 4 tornillos que sostienen la BASE del Televisor;

ahora la BASE puede ser separada del Televisor. Para dimensiones del ensamble en la PARED referirse a la pag. 139.

METAL de la BASE

2 Tornillos

BASE del TELEVISOR

NOTA: Use la base para pared (WALL MOUNT) para el Televisor de Plasma de acuerdo al tamaño.

Visite nuestro sitio de internet: www.hitachi.us/tv para accesorios de su Televisor.

Quitar estos 2 tornillos

primero, para separar el

Televisor del metal de la

base. Luego poner estos

2 tornillos de nuevo al

Quitar estos 4 tornillos

para separar el Televisor

de la base.

Televisor.

PRECAUCIÓN - Este televisor de Plasma solo puede usar la base para la pared WM07S de Hitachi. Al usar otra

base puede causar inestabilidad en el televisor provocando posibles heridas personales.

Para el Modelo P42T501

Uso por primera vez

test-bleed 3/3/06 10:18 AM Page 7

AIR / CABLE

Cómo configurar su nuevo televisor de plasma Hitachi

VISIÓN

La mejor posición para ver la imagen es en frente

del televisor y de 10 a 18 pies lejos de la pantalla.

Durante las horas del día, las reflexiones o reflejos

de luz externa pueden aparecer en la pantalla. Si

esto sucede, pueden ser usadas cortinas para reducir el

reflejo o la TV puede cambiarse de lugar en el cuarto.

Si el audio del televisor es conectado a las bocinas de

un sistema de alta fidelidad (Hi-Fi), la mejor

calidad de audio se obtendrá al colocar las bocinas

equidistantes a los lados del receptor y los más

cerca posible a la altura del centro de la imagen.

Para una mejor separación de audio(stereo),

coloque las bocinas por lo menos 4 pies de los

lados del Televisor, coloque las bocinas traseras

(surround speakers) a lado o detrás del angulo de vision.

Diferencias en tamaño de los cuartos y ambientes

acústicos requiren alguna experimentación con la

colocacion de las bocinas para una mejor calidad de

CONEXIONES DE ANTENA EN EL

PANEL POSTERIOR

Antena VHF (75-Ohm) /CATV (Cable TV)

Al usar un sistema de cable coaxial 75-Ohm, conectar el cable coaxial de señal CATV a la terminal AIR/CABLE (75-Ohm) .

O si tiene una antena, conectar al cable coaxial a la misma terminal AIR/CABLE.

VHF (300-Ohm) antenna/UHF antenna

Al usar un cable plano de 300-Ohm de una antena

externa, conectar los cables de la antena VHF ó UHF

a los tornillos del adaptador VHF ó UHF. Insertar el

adaptador a la terminal de antena en el TV.

Al usar ambas antenas VHF y UHF

conectadas

Usar un mezclador de cable/antena opcional conectado

a la terminal de antena, y conectar los cables al mezclador.

Consultar con su distribuidor o centro de servicio por los

mezcladores de antena.

Al cable de señal CATV

A la antena externa

A la antena externa VHF

ó antena UHF

A la antena externa

ó sistema de CATV

A la antena

UHF

Mezclador de Antena

AIR / CABLE

NOTA: Al conectar un cable plano de 300-Ohm puede causar interferencia. Usar un cable coaxial

de 75-Ohm es más recomendable.

audio.

4" Minimo

MEJOR

ANGULO DE

VISIÓN HORIZONTAL

10'

15' 20'

Uso por primera vez

test-bleed 3/3/06 10:18 AM

SALIDA DE AUDIO

3.8mm

ESTÉREO

MINI-CONECTOR

CONECTORES

TIPO RCA

plano 300-Ohm doble hilo

Este cable de antena externa debe ser conectado a un

adaptador de antena (300-Ohm a 75-Ohm).

Usado en todos los cables de video y audio estándar

los cuales conectan las entradas y salidas localizados

en la parte posterior y panel de control frontal del televisor.

Cable Coaxial tipo “F” a 75-Ohm

Para conectar señales de RF (antena ó cable TV) a la

terminal de antena en el televisor.

Cable S-Video (Super Video)

Este conector es usado en videocámaras, VCRs y repro-

ductores de laser con la opción S-Video en lugar del cable

de video estándar para producir una imagen de alta calidad.

Cable Óptico

Este cable es usado para conectar a un amplificador de

audio con entrada de Audio Optica. Usar este cable para

la mejor calidad de sonido.

Cable HDMI

Este cable es usado para conectar sus equipos externos como

Set-Top-Boxes ó reproductores de DVD equipados con

salida HDMI conectada a la entrada HDMI del Televisor.

Cable Estéreo (Terminal audifono 3.8mm a 3.5mm )

Usado en todos los cables de audio y video estándar que

conectan las entradas y salidas localizadas en la parte

posterior o en el panel de control frontal del televisor.

Cables y Conectores

La mayoría de las conexiones de audio/video entre equipos puede hacerse con cables blindados de audio y video que

tienen conectores RCA. Para una mejor calidad, los cables de video deben ser coaxiales blindados de 75-Ohm.

Los cables pueden ser comprados en la mayoría de las tiendas que vendan productos de audio/video. Enseguida

unas ilustraciones y nombres de conectores. Antes de comprar cualquier cable, asegúrese de los tipos de conectores

de salida y entrada requeridos por los diferentes tipos de equipos y el largo de cada cable.

Cable

Cable Phono ó RCA

Uso por primera vez

test-bleed 3/3/06 10:18 AM

Además de controlar todas la funciones de su Televisor de Plasma Hitachi, el nuevo control remoto es diseñado para

operar diferente tipos de equipos, tales como, reproductores de DVD, CBL (Cajas de Cable), set-top-boxes, receptores

de satélite, y VCRs. El control remoto debe ser programado para controlar el equipo deseado. Ver páginas 95-110

para una completa descripción de todas las opciones y como programar el Control Remoto.

2. El código de la VCR está incluido en el modo de PVR.

SIGNIFICADO

TV – Televisión PVR – Grabadora Personal de Video

CBL – Caja de Cable DVD – Reproductor de Disco Digital de Video (DVD)

SAT – Satélite

BOTÓN de Encendido (POWER)

(TV, DVD, SAT/CBL,PVR/VCR)

Enciende ó apaga el equipo elegido.

BOTÓ

N DE LOS EQUIPOS (SOURCE ACCESS)

(TV, DVD, PVR/VCR, SAT/CBL)

Cambia el modo del Control Remoto Universal para

controlar el equipo elegido.

BOTONES DEL DVD/VCR

(DVD, PVR/VCR)

Controlan las funciones de su VCR, DVD y equipos de

audio.

BOTÓN DIA/NOCHE (DAY/NIGHT)

(TV)

Cambia entre los modos de imagen Día y

Noche (NIGHT).

BOTÓN DEL ASPECTO ó FORMATO (ASPECT)

(TV)

Changes the aspect ratio of the TV.

BOTÓN DE CONTROL DEL PIP (Picture-in-Picture)

(TV)

Presionar para mostrar el modo del PIP.

BOTÓ

N de MENU

(TV,DVD,SAT/CBL,PVR/VCR)

Accesa el menú en pantalla (OSD menu).

BOTÓ

N (-)

(TV,STB)

El botón (-) es usado al estar el control remoto

en modo Set-Top-Box (STB) ó cuando el TV usa

un canal digital (HD).

BOTONES NUMÉRICOS

(TV, DVD, SAT/CBL, PVR/VCR)

Usados para poner manualmente el el canal en el

Televisor, y usados para poner números dentro

de la navegación del menú en pantalla (OSD).

BOTÓ

N de la GUÍA

(

SAT/CBL, PVR)

Accesa la guía de programación de canales de

otros equipos.

BOTÓN PARA SALIR (EXIT)

(TV, SAT/CBL, PVR/VCR)

Sale de algún sistema de menú OSD ó INPUTS

si es que el menú es desplegado.

BOTÓN de Canal Anterior (LAST CH)

(TV, SAT/CBL, PVR)

Cambia entre el canal actual y el último canal visto

BOTÓN ENTER

Presionar para usarlo como la opción SELECT.

Solo se puede usar al estar el control en modo TV.

BOTÓN de Información (INFO)

(TV, STB, CBL, PVR)

Desplega varia información en la imagen tal como

información del canal , horario, entrada, etc.

BOTONES DE CANALES ARRIBA & ABAJO

(TV, CBL, STB, PVR/VCR)

Cambia hacia arriba ó abajo los canales.

BOTONES CURSOR/SELECT

(TV, DVD, SAT/CBL,PVR/VCR)

Los botones CURSORES son usados para

navegar el cursor dentro del menú en pantalla y

las entradas (INPUTS), y el botón SELECT es

usado para Elegir/Activar la opción marcada.

BOTONES DE VOLUMEN

(TV )

Ajusta el nivel de audio de su Televisor, ya sea

incrementando ( ) ó reduciendo ( ).

BOTÓN DE PAUSA

(TV, PVR/VCR, DVD)

Presionar para mostrar y cambiar el modo Freeze del TV.

También se usa para pausar otros equipos al estar el

control remoto en modo DVD ó PVR/VCR.

BOTÓ

N de Entradas (INPUTS)

(TV)

Accesa el menú de Entradas (INPUTS).

INDICADOR DEL MODO

Enciende ó parpadea para mostrar el modo

en el que está el Control Remoto al ser

presionado el botón SOURCE SELECT.

BOTÓN CC (Subtítulos)

(TV)

BOTÓN de Volumen Bajo (MUTE)(TV)

Reduce el nivel de audio a 50% si se presiona una

vez, y se apagará por completo si se presiona

dos veces. Presionar una tercera vez más para

restaurar el nivel de audio.

BOTÓN DE CANALES FAVORITOS (FAV CH)(TV)

Presionar para entrar/accesar el modo de canales

favoritos (FAV CH). (Los canales favoritos solo operan

en modo TV).

Presionar para mostrar y cambiar el modo de

subtítulos (Closed Caption).

anteriomente.

NOTAS : 1. EL sensor de control remoto del TV está localizado en la parte inferior derecha de la pantalla.

para controlar las funciones del TV, Apunte el control remoto directamente al sensor de control

remoto para mejor resultado.

Guía Rápida para las Funciones del Control Remoto

Uso por primera vez

VCR – Reproductor de Videocassete

test-bleed 3/3/06 10:18 AM Page 10

PRESIONAR PARA ABRIR LA PUERTA

VISTA FRONTAL

햲

햺

햹

햸

햴

햳

햶

햷

햲 Botón Frontal de Encendido (POWER)

Presionar este botón para encender ó apagar el

Televisor de Plasma . También puede ser encendido

ó apagado con el control remoto. El switch principal

tiene que estar en modo de espera (stand-by).

햳 Botón MENU/SELECT

Este botón permite entrar al MENU, haciendo posible

configurar las opciones del Televisor a su preferencia

sin usar el control remoto. Este botón también sirve

como el botón SELECT al estar en modo de MENU.

햴

HDMI-FRONT (Frontal)

Usar esta entrada HDMI para equipos externos como

Set-Top-Boxes ó DVD equipados con conexión de

salida HDMI (ver página 87 para referencia).

햵 Botón de entradas y salir INPUT/EXIT

Presionar este botón para accesar a las entradas.

Presionar de nuevo para salir del modo de MENU.

햶 Selector de Canales

Presionar estos botones hasta que el canal deseado

aparezca en la esquina superior derecha de la imagen.

Estos botones también sirven como los cursores ()

abajo y arriba () al estar en el MENU.

햷 Nivel de VOLUMEN

Presionar estos botones para ajustar el nivel de sonido.

El nivel de volumen será desplegado en la imagen.

Estos botones también sirven como los cursores () izq.

y derecha () al estar en el MENU.

햸 Botón de Encendido Principal (MAIN POWER)

del Televisor

Este botón es para la energía principal del TV, y

debe ser encendido o apagado manualmente. Se

recomienda dejar activado el “Botón Principal”

en la condición de espera (Indicador en Rojo).

NOTA: Al estar el botón “MAIN POWER” apagado (OFF)

ó el Televisor está desconectado, el reloj

se detendrá y eventualmente se restablecerá.

햽

Controles del Panel Frontal

햵

CONTROLES DEL PANEL FRONTAL

Tarjeta de Actualización de Software (Upgrade Card)

Está opción es para mejoras futuras de software.

Hitachi le notificará si una actualización de software

es requerida a su Televisor. Para poder recibir una

notificación por escrito, favor de llenar y enviar la

tarjeta de garantía.

햻

햹

DEL PANEL DE CONTROL

PUSH EJECT

PHOTO INPUT

Entrada de Fotos (SD CARD PHOTO INPUT)

Está entrada también sirve para ver fotografías

tomadas con una camara digital, solo insertar

la tarjeta tipo SD en la ranura para ver sus fotos.

햹

El botón principal

está localizado en la

parte inferior del Tele-

visor , bajo la marca

que indica

" ".

Uso por primera vez

test-bleed 3/3/06 10:18 AM

Sensor de CONTROL REMOTO (R/C)

Apuntar su control remoto en está area al elegir

canales, ajustando volumen, etc.

햺

햻

Terminales de Entrada Frontal (INPUT-FRONT)

Está entrada provee terminales de video compuesto

para conectar equipo con está capacidad, tales

como reproductores de DVD ó Videocamaras.

Controles del Panel Frontal

Luz Indicadora de Encendido (POWER LED)

Para encender el Televisor, presionar el switch princi-

pal localizado en la esquina inferior derecha

del TV. Un luz indicadora roja se encenderá

en la esquina inferior derecha del marco del

Televisor. El Televisor de Plasma esta listo para la

operación del control remoto ON/OFF.

NOTAS: 1. El Televisor de Plasma HITACHI podrá aparentar estar apagado (Indicador Naranja) si no hay señal de

entrada en INPUT : 1, 2, 3 ,FRONT y HDMI 1,2 y FRONT. Verificar la luz indicadora para asegurarse de que

el TV está apagado ó está en modo de espera (Stand-by) (Indicador Rojo) al no estar en uso el Televisor.

2. El Control Remoto no puede encender o apagar el Switch Principal del Televisor.

햽

Luz Indicadora

Sensor R/C

햺

햻

Luz Indicadora Estado Operación

OFF. Al estar el switch principal apagado (Off).

Al estar el switch principal del Televisor

(Stand-by) encendido (ON).

Switch Principal encendido ON ; pero sin señal

de entrada excepto antena (sin señal de sincronía).

Off

Enciende

Rojo

OFF.

Enciende

Azul

Switch Principal encendido ON; se ve imagen.

Enciende

Naranja

Off

(Ahorro de energía)

Parpadea

Azul 3 veces

Al recibir señal del Control remoto cada vez que

que se presione una tecla.

Uso por primera vez

test-bleed 3/3/06 10:18 AM Page 12

Uso por primera vez

햲

햳

햸

햹

햴

햷

햺

햵

햶

햲 Entrada de Antena

Para cambiar entre la señal Cable y Aérea, ir a la

opción de Organizar Canales (Channel Manager)

para cambiar el tipo de señal CABLE ó Aérea.

햳 Entradas de Audio/Video 1, 2 y 3

Al usar el botón INPUTS , los CURSORES ( 

y ), y el botón SELECT ó el CURSOR derecho

 del control remoto, se puede elegir cada entrada

de video. Usar las entradas de audio y video para conec-

tar equipos externos, tales VCRs, video cámaras,

reproductores de DVD, etc. (Si tiene sonido

monoaural, insertar el cable de audio en la terminal

izquierda de audio).

햴 Salida de MONITOR y Salida de Audio

Estas terminales proveen audio fijo, además

señales de video (Cable/Aérea ó INPUTS)

las cuales son usadas para grabación. Usar la salida

S-Video para una mejor calidad de video. Señal de

componente en las entradas 2 y 3, y las entradas

HDMI no tendrán salida de monitor.

햵 Salida óptica (Audio Digital)

Esta terminal provee Salida de Audio Digital para su

equipo de audio que es compatible con Dolby

Digital y PCM, tal como un amplificador de audio.

NOTA: *Fabricado bajo licencia de Dolby

Laboratories. “Dolby” y el símbolo

doble-D son marcas registradas de Dolby

Laboratories.

햶 Entrada S-VIDEO 1

La entrada 1 provee una terminal S-VIDEO

(Super Video) para conectar equipo con capacidad

de salida S-VIDEO.

NOTA: 1. Se pueden usar la entradas VIDEO ó S-VIDEO

para conectar en INPUT 1, pero solo una

de estas entradas puede usarse a la vez.

2. La salida S-VIDEO puede usarse para

grabación, solo cuando la entrada es

del tipo S-VIDEO.

햷 Entradas HDMI 1, 2 (High Definition Multimedia

Interface)

Acerca del HDMI – HDMI es la

nueva-generación de interface digital para equipos

electrónicos. El HDMI permite la segura distribución

de video de alta definición sin comprimir y múltiples

canales de audio en un solo cable. Porque las señales

digitales de TV (DTV) permanecen en formato digital,

el HDMI asegura que las imagenes de alta-definición

mantengan la mas alta calidad de video desde un

equipo a la pantalla de su Televisor.

Usar la entrada HDMI para conectar equipos externos

tales como Set-Top-Boxes ó reproductores de DVD

equipados con conexión de salida HDMI .

HDMI, el logotipo HDMI y el nombre High-Definition

Multimedia Interface son marcas registradas de

la compañía HDMI Licensing LLC.

NOTA: 1. La entrada HDMI no esta diseñada para

usarse con computadoras personales.

2. Solo formatos DTV tales como 1080p,1080i, 720p,

480i y 480p están disponibles para la entrada HDMI.

햸 Entrada por Componente:Y-P

BPR Inputs

Las entradas 2 y3 proveen terminales Y-P

BPRpara conectar

equipos con esta capacidad, tales como reproductores

de DVD ó Set Top Box. Se puede usar señal de video

compuesto para ambas entradas.

NOTA:1. No conectar VIDEO compuesto y S-VIDEO

en la entrada INPUT 1 al mismo tiempo.

S-VIDEO tiene prioridad sobre la entrada de VIDEO.

2. Las salidas por componente de su equipo pue-

den llamarse Y, B-Y, y R-Y. En este caso, conectar

la salida por componente B-Y a la entrada P

del TV y la salida por componente R-Y a la

entrada P

R del televisor.

3. Las salidas por componente de su equipo pue-

den llamarse Y-C

BCR. En este caso, conectar

la salida por componente C

B a la entrada PB del

TV y la salida por componente CR a la entrada PR.

4. Puede ser necesario ajustar el TINTE para

obtener una óptima calidad de imagen al usar

la entradas Y-P

BPR (ver pag. 113).

5. Para evitar faltas sobre el derecho de autor, la

salida MONITOR OUT será anormal, al usar

las terminales Y-P

BPR y la entrada HDMI.

6. La entradas 2 y 3 (Y/VIDEO) pueden ser

usadas para video compuesto y entrada de

video por componente.

햹 Para control Especial de AV solamente.

햺 Para uso en la fábrica solamente.

Conexiones del Panel Posterior

test-bleed 3/3/06 10:18 AM Page 13

Las entradas en el panel FRONTAL se proveen para su conveniencia permitiendole la fácil conexión de señales HDMI

o DVI de un DVD, Set Top Box y Video Juego como se muestra en los siguientes ejemplos: (Al conectar señales DVI

OUTPUT

L R

DIGITALOUTPUT

DVI a HDMI

Cable

Parte posterior del

HDTV Set-Top-Box ó

Reproductor de DVD

Equipo con Capacidad

de Salida DIGITAL HDMI

DVD , Set Top Box,

Consola de Video Juegos.

CONTROLES DEL PANEL FRONTAL

Equipo con Capacidad

de Salida DIGITAL DVI

DVD , Set Top Box,

Consola de Video Juegos.

será necesario conectar la salida de audio a las entradas de audio FRONTALES del Televisor) :

A) Conectando señal HDMI.

B) Conectando señal DVI.

CONTROLES DEL PANEL FRONTAL

pecificaciones del equipo.

Nota : Cables especiales de los equi-

pos serán de acuerdo a las es-

Conectando Equipos de Video Externos

NOTA: Inserte completamente los conectores cuando conecte las entradas del panel frontal. De no hacerlo, la

imagen desplegada puede ser anormal.

pecificaciones del equipo.

Nota : Cables especiales de los equi-

pos serán de acuerdo a las es-

PUSH EJECT

PHOTO INPUT

Uso por primera vez

test-bleed 3/3/06 10:18 AM Page 14

Uso por primera vez

PUSH EJECT

Las terminales Frontales se proveen para su conveniencia permitiendole la fácil conexión de una Cámara

de Video, un DVD, Video Juego, VCR y una Cámara Digital como se muestra en los siguientes ejemplos:

NOTA: Inserte completamente los conectores cuando conecte las entradas del panel frontal. De no hacerlo, la

imagen desplegada puede ser anormal.

Conectando Equipos de Video Externos

CONTROLES DEL PANEL FRONTAL

especificaciones del equipo.

Nota : Los cables especiales de los

equipos deben ser de acuerdo a las

Video Juego

Video Cámara

Equipo con Capacidad de

Salida Video Compuesto

Reproductor de DVD

Consola de Video Juegos.

OUTPUT

L R

Video

El acomodo exacto que usted use para conectar el VCR, videocámara, reproductor de discos láser, DVD o

Set Top Box HDTV para su televisión depende del modelo y funciones de cada componente. Revise el manual

operativo de cada componente para la ubicación de entradas y salidas de audio y video.

Los siguientes diagramas de conexión se ofrecen como sugerencia. Sin embargo, usted tal vez tenga que

modificarlos para ajustarse a su combinación particular de componentes y funciones. Para mejor desempeño,

los cables de video y audio deben ser coaxiales y blindados.

Antes de Operar Equipos Externos de Video

Conecte un equipo externo a la terminal de ENTRADA, después presione el botón INPUTS para mostrar el

Menú de ENTRADAS. Use los CURSORES ( y ) para seleccionar la Entrada de su preferencia. Entonces

presione el botón SELECT o el CURSOR

 para confirmar su elección (ver pag. 98).

PHOTO INPUT

HDMI-Frontal

Fotos

Aérea/Cable

Entrada 1

Move SEL Sel.

Entrada 2

audio en la entrada L/Mono .

Nota : Para dispositivos m

onoaurales

favor de conectar el cable de

test-bleed 3/3/06 10:18 AM Page 15

Uso por primera vez

NOTA: Los Cables son opcionales, excepto cuando se especifica.

Equipo con Capacidad

de Salida Digital HDMI

HDMI OUTPUT

HDMI

VCR #1

TV por Cable TV (Cable coaxial)

Divisor de señal 2-Vías

Antena Externa

ANT

OUTPUT

S-VIDEO

VL R

Equipo con Capacidad

de Salida Digital DVI

DIGITAL OUTPUT

OUTPUT

Y P

L R

HDTV Set-Top Box

Reproductor de DVD

DVI

HDMI

AUDIO OUT

OUTPUT

L R

VCR #2

V L R

INPUT

S-VIDEO

Opcional

Conexiones del Panel Posterior

test-bleed 3/3/06 10:18 AM Page 16

Uso por primera vez

• Las conexiones S-VIDEO, Y-PBPR, ó HDMI se proveen para equipos de alta fidelidad tales como DVD's,

VCR's etc. que cuenten con esta opción. Use estas conexiones en lugar de una conexión de video estándar

si su dispositivo cuenta con esta opción.

• Si su dispositivo tiene solamente una salida de audio (monoaural), conéctelo al canal izquierdo(L/MONO) en

el panel posterior de la televisión.

• Consulte el manual de operación de sus otros equipos electrónicos para información adicional sobre como

instalar sus cables de entrada/salida.

• Una sola VCR puede ser usada para VCR #1 y VCR #2, pero recuerde que un VCR no puede grabar su propio

video o línea de salida (INPUT: 1 en el ejemplo de la página 89). Consulte la guía de operación de su VCR

para más información en las conexiones de entrada y salida.

• Conecte solamente 1 equipo (VCR, Reproductor de DVD, videocámara, etc.) a cada terminal de entrada.

• Las conexiones por COMPONENTE Y-P

BPR (ENTRADAS 2 y 3) se proveen para equipos de alta fidelidad

tales como DVD's y Set Top Box's. Use estas conexiones en lugar de una conexión de video estándar si su

dispositivo tiene esta opción

• Las salidas por componente de su equipo pueden llamarse Y, B-Y, and R-Y. En este caso, conectar la salida

por componente B-Y a la entrada PB del TV y la salida por componente R-Y a la entrada PR del televisor.

• Las salidas por componente de su equipo pueden llamarse Y, CBCR. En este caso, conectar la salida

por componente CB a la entrada PB del TV y la salida por componente CR a la entrada PR del televisor.

• Puede ser necesario ajustar el TINTE para obtener una óptima calidad de imagen al usar la entradas

Y-P

BPR (ver página 113).

• Para asegurarse de no infringir las leyes sobre derechos de autor, la Salida de Monitor será anormal, cuando se

usen las entradas Y-PBPR y las entradas HDMI.

• Las entradas HDMI 1, HDMI 2 ó HDMI FRONTAL pueden recibir señales de HDMI.

• La Salida de Monitor S-VIDEO puede ser usada para grabar unicamente cuando la entrada sea S-VIDEO.

• Al usar la entrada HDMI desde un Set-Top-Box,se recomienda usar una señal de entrada 1080i o 720p.

RECOMENDACIONES PARA LA INSTALACIÓN:

1. Las Señales de Video que pasan a través de una VCR pudieran ser afectadas por el sistema de proteccion de

derchos de autor y la imagen aparecerá distorcionada en la televisión.

2. Al conectar la televisión directamente a las salidas de Audio/Video de un Set-Top-Box se asegura una mejor

calidad de imagen.

• Al conectar una señal de 1080p por HDMI la longitud del cable de HDMI debe ser menor de 5 metros.

Consejos sobre las Conexiones del Panel Posterior

test-bleed 3/3/06 10:18 AM Page 17

Uso por primera vez

Parte posterior

de la VCR

OUTPUT

VCR

Video

CONECTANDO UNA FUENTE DE VIDEO Y AUDIO

ESTEREO A LAS ENTRADAS 1 ~ FRONTAL

1. Conecte el cable de la salida de video (VIDEO OUT)

del VCR o del Reproductor de Laserdisc a la

entrada de video(VIDEO/Y) como se muestra en el

Panel Posterior.

2. Conecte el cable de la salida de audio derecha

(AUDIO OUT R) del VCR o Reproductor de Laserdisc

a la entrada de audio derecha (AUDIO/R).

3. Conecte el cable de la salida de audio izquierda

(AUDIO OUT L) del VCR o Reproductor de Laserdisc

a la entrada de audio izquierda(AUDIO/L).

4. Presione el botón INPUTS, entonces seleccione la

ENTRADA 1~ FRONTAL del Menú de Entradas para

ver el programa de su VCR o Reproductor de Laserdisc.

5. Seleccione la señal CABLE o AEREA en el Menú

de Entradas para regresar al último canal sintonizado.

NOTA: 1. Inserte completamente los conectores al hacer las conexiones del panel posterior. La imagen y el

sonido que se está reproduciendo será anormal si la conexión está floja.

2. Una sola VCR puede ser usada para VCR #1 y VCR #2, (ver página 89) pero recuerde que una VCR no

puede grabar su propio video o línea de salida. Consulte la guía de operación de su VCR para más

información en las conexiones de entrada y salida.

3. Cuando se usen las ENTRADAS 2 ó 3, es necesario conectar la salida de video del dispositivo a la

terminal de entrada Y/VIDEO del Televisor.

CONECTANDO SEÑAL S-VIDEO Y AUDIO ESTEREO

DE UN EQUIPO A LA ENTRADA (INPUT 1)

Conectando Equipos de Video Externos

VCR ó Laserdisc

OUTPUT

Parte posterior de VCR ó

Laserdisc

S-VIDEO

Video L R

Cable ó

Señal Aérea

Cable ó

Señal Aérea

1. Conecte el cable de la salida de video S-VIDEO

del VCR S-VHS o Reproductor de Laserdisc a la

entrada S-VIDEO de la TV, como se muestra en

el Panel Posterior .

2. Conecte el cable de la salida de audio derecha

(AUDIO OUT R) del VCR o Reproductor de Laserdisc

a la entrada de audio derecha (AUDIO/R)

3. Conecte el cable de la salida de audio izquierda

(AUDIO OUT L) del VCR o Reproductor de Laserdisc

a la entrada de audio izquierda (AUDIO/L)

4. Presione el botón INPUTS, entonces seleccione la

ENTRADA 1 del Menú de Entradas para ver el

programa de su VCR o Reproductor de Laserdisc.

5. Seleccione CABLE o AÉREA en el Menú de

Entradas para regresar al último canal sintonizado.

NOTA :1.Inserte completamente los conectores al hacer las conexiones del panel posterior. La imagen y el

sonido que se esta reproduciendo será anormal si la conexion está floja.

2.Un solo VCR puede ser usado para VCR #1 y VCR #2, (ver página 89) pero recuerde que un VCR no

puede grabar su propio video o línea de salida. Consulte la guía de operación de su VCR para más

información en las conexiones de entrada y salida.

test-bleed 3/3/06 10:18 AM Page 18

Conectando Equipos de Video Externos

Uso por primera vez

CONECTANDO UN EQUIPO CON SALIDA HDMI

HDTV Set-Top-Box ó

Reproductor de DVD

Cable

HDMI

OUTPUT

DIGITAL OUTPUT

Cable

DVI a HDMI

Parte posterior del

HDTV Set-Top-Box ó

Reproductor de DVD

Entrada HDMI

Entrada DVI a HDMI

Cable

Señal Aérea

HDTV Set-Top-Box ó

Reproductor de DVD

Cable

Señal Aérea

DIGITAL OUTPUT

Parte posterior del

HDTV Set-Top-Box ó

Reproductor de DVD

O DVI A LAS ENTRADAS HDMI 1, 2 Ó FRONTAL

1. Conecte el conector HDMI o el adaptador

DVI/HDMI de la salida del Set Top Box HDTV

o Reproductor de DVD a la entrada HDMI

tal como se muestra en la parte de abajo.

2. Al usar salida DVI, conecte el cable de la salida

de audio derecha(AUDIO OUT R) del Set Top Box

HDTV o DVD a la entrada derecha(AUDIO IN/R)

tal como se muestra en la parte de abajo.

3. Al usar salida DVI, conecte el cable de la salida

de audio izquierda(AUDIO OUT L) del Set Top Box

HDTV o DVD a la entrada izquierda(AUDIO IN/L)

tal como se muestra en la parte de abajo.

4. Presione el botón INPUTS, entonces seleccione

HDMI 1, HDMI 2 o HDMI-FRONTAL para ver el programa

del Set Top Box HDTV o el Reproductor de DVD.

5. Seleccione CABLE o AÉREA en el Menú de

Entradas para regresar al último canal sintonizado.

NOTA:1. Inserte completamente los conectores al

hacer las conexiones del panel posterior.

La imagen y el sonido que se esta reprodu-

ciendo será anormal si la conexion está floja.

Las entrada HDMI en HDMI 1, HDMI 2 y HDMI-

FRONTAL contienen el sistema de protección

contra copiado llamado High-bandwidth Digital

Content Protection(HDCP). El HDCP es un sistema

que codifica las señales de video cuando se

usan conexiones HDMI, para prevenir el

copiado ilegal de la información de video.

3. HDMI no es una tecnologia de “RED”,

establece una conección punto-a-punto en

un solo sentido para la entrega de video no

comprimido en una pantalla.

4. El dispositivo digital conectado controla la

interface HDMI, por lo tanto la configuración

adecuada de las opciones de usuario del

equipo determinan la resolución final del video.

5. Al usar un adaptador DVI a HDMI, conecte los

cables de salida de audio Audio Out L y R a la

misma HDMI (1 , 2 ó FRONT) que conectó

el cable HDMI. (Para HDMI-FRONTAL favor de

consultar la página 87 )

test-bleed 3/3/06 10:18 AM Page 19

Conectando Equipos de Video Externos

Uso por primera vez

CONECTANDO UN EQUIPO CON SALIDA DE COMPONENTES

Y DE AUDIO EN LAS ENTRADAS 2 ó 3 : Y-PBPR.

1. Conecte el cable de la salida Y del reproductor

Laserdisc/Reproductor de DVD ó HDTV set top

box a la entrada (Y), como se muestra en el

panel posterior de la figura.

2. Conecte el cable de la salida P

B/CB ó B-Y

del Laserdisc/Reproductor de DVD ó HDTV

set top box a la entrada PB del TV.

3. Conecte el cable de la salida PR/CR ó R-Y

OUT del Laserdisc/Reproductor DVD ó HDTV

set top box a la entrada PR del TV.

4. Conecte el cable de la salida de audio derecha

(AUDIO OUT R) del Set Top Box HDTV o DVD

a la entrada de audio derecha(AUDIO/R).

5. Conecte el cable de la salida de audio izquierda

(AUDIO OUT L) del Set Top Box HDTV o DVD

a la entrada de audio izquierda(AUDIO/L).

6. Presione el botón INPUTS, entonces seleccione

la ENTRADA 2 ó 3 del Menú de Entradas para

para ver el programa del Set Top Box HDTV o

el Reproductor de DVD/Laserdisc.

7. Seleccione CABLE ó AÉREA en el Menú de

Entradas para regresar al último canal sintonizado.

NOTA: 1. Inserte completamente los conectores al

hacer las conexiones del panel posterior.

La imagen y el sonido que se está reprodu-

ciendo será anormal si la conexión está floja.

2. Ver pág. 90 para sugerencias sobre las

CONEXIONES DEL PANEL POSTERIOR.

OUTPUT

Reproductor de DVD

Parte posterior del

Reproductor de DVD

OUTPUT

L R Y P

B P

HDTV Set-Top Box

PR/CR PB/CB Y

VIDEO

AUDIO

CABLE

Señal Aérea

test-bleed 3/3/06 10:18 AM Page 20

Uso por primera vez

CONECTANDO UN EQUIPO DE VIDEO Y AUDIO

MONAURAL A LAS ENTRADAS 1, 2, 3 ó FRONTAL

1. Conectar el cable de la salida de video(VIDEO OUT)

del VCR o del Reproductor de DVD a la entrada

de video(VIDEO/Y) como se muestra en el Panel

Posterior de la derecha.

2. Conectar el cable de la salida de audio(AUDIO OUT)

de su VCR o Reproductor de DVD a la entrada

(MONO)/AUDIO IN L) de su TV .

3. Presione el botón INPUTS, entonces seleccione la

ENTRADA 1,2,3 ó Frontal del Menú de Entradas

para ver el programa de su VCR o Reproductor DVD.

4. Seleccione CABLE o AÉREA en el Menú de

Entradas para regresar al último canal sintonizado.

CONECTANDO UN AMPLIFICADOR DE AUDIO EXTERNO

Para controlar el nivel de audio del TV de Plasma con un

amplificador externo de audio, conectar el sistema

como se muestra en la derecha. La salida “OPTICAL OUT”

del panel posterior es una salida fija. El Volumen del

amplificador es controlado por el amplificador, no por

el televisor de Plasma. La terminal OPTICAL OUT se

puede conectar a todo equipo con Entrada Óptica.

1. Conectar un cable óptico desde la salida Optical out a

la entrada Óptica de un sistema de sonido ó

Amplificador como se muestra en el Panel poste-

rior como la figura de la derecha.

NOTA: Al hacer conexiones de video, conectar solo S-Video ó solo Video. Si ambas son conectadas, el

S-Video tiene prioridad.

CABLE

Señal Aérea

VCR ú otros equipos

externos

INPUT

S-VIDEO

R L V

Opcional

(Para la ENTRADA FRONTAL consultar la página 88).

Conectando Equipos de Audio/Video Externos

CABLE

Señal Aérea

Sistema de Amplificador

OPTICAL

Sistema de Amplificador

ó sistema de DVD

CABLE

Señal Aérea

Parte posterior del

VCR

OUTPUT

VCR

VIDEO OUT AUDIO OUT

CONEXIÓN DE LA SALIDA DE MONITOR

La Salida de Monitor (Monitor Out) proporciona audio y

video de las señales CABLE/AÉREA y las Entradas 1, 2, 3,

y Frontal. No proporciona Video por Componente ó HDMI.

1. Conexión de S-Video:

Conect

ar el cable de la salida S-VIDEO del

Panel Posterior a la entrada S-VIDEO del VCR.

Conexión de Video:

Conectar el cable de la salida VIDEO del

Panel Posterior a la entrada VIDEO del VCR.

2. Conectar el cable de la entrada AUDIO IN R del

VCR a la salida AUDIO/R del Panel Posterior del

Televisor.

3. Conectar el cable de la entrada AUDIO IN L del

VCR a la salida

AUDIO/L del Panel Posterior del

Televisor.

El Control Remoto

Además de controlar todas las funciones de su TV

Plasma HITACHI, el nuevo control remoto está diseñado

para operar diferentes tipos de VCRs, convertidores

CATV, decodificadores de cable, receptores satelitales

reproductores DVD, y otros equipos de audio/video con

solo apretar un botón. Todas las teclas de operación

básicas están agrupadas en una sola área.

Para operar su TV Plasma, seleccione TV presionando

el botón Source del Source Select en el remoto. El

indicador del modo TV parpadeará, indicando que el

control remoto está listo para operar su televisor.

Para operar su receptor de cable, seleccione SAT/CBL

presionando el botón Source del Source Select en el

remoto. El indicador del modo SAT/CBL parpadeará,

indicando que el control remoto está listo para operar su

receptor de cable. (Vea las instrucciones en la pág. 104

para programar el control remoto y operar su receptor

Para operar su STB (Set-top-box) o receptor satelital,

seleccione SAT/CBL presionando el botón Source del

Source Select en el remoto. El indicador del modo

SAT/CBL parpadeará, indicando que el control remoto

está listo para operar su STB. Si usted tiene un receptor

satelital, use también este botón para programar su

receptor satelital.(Vea las instrucciones en la pág. 105

para programar el control remoto y operar su STB o

Para operar su reproductor DVD, seleccione DVD

presionando el botón Source del Source Select en el

remoto. El indicador del modo DVD parpadeará,

indicando que el control remoto está listo para operar su

reproductor DVD. ( Vea las instrucciones en la pág. 106

para programar el control remoto y operar su

Para operar su VCR/PVR (Grabadora de Video Personal),

seleccione PVR/VCR presionando el botón Source del

Source Select en el remoto. El indicador del modo

PVR/VCR parpadeará, indicando que el control remoto

está listo para operar su VCR/PVR. (Vea las instrucciones

en la pág. 107 para programar el control remoto y operar

su VCR/PVR).

de cable).

receptor satelital).

reproductor DVD).

El Control Remoto

쐃

쐇

쐋

쐏

쐄

쐂

쐆

쐊

쐎

쐅

씈

씌

쐈

쐉

씉

씊

씋

Freeze

쐄

Presione este botón para seleccionar el modo del control

remoto.

Botón SOURCE SELECT

쐃

Botón de encendido/apagado (POWER)

Presione este botón para encender o apagar el televisor

cuando el remoto este en modo TV. (Ver página 95 para

las instrucciones de como programar el control remoto en

modo TV).

Botones de MODO

쐇

쐋

Enciende o parpadea tres veces para mostrar el modo

del control remoto.

Botón DIA/NOCHE (DAY/NIGHT)

Presione este botón para cambiar entre las configuraciones

de modo de imagen Día(Normal), Día(Dinámico) y

Noche. Seleccione los modos de Día para ver durante el

día con mayor brillo y contraste para competir con la luz

interior del cuarto. Seleccione Noche para ver durante la

noche con menor brillo y contraste para una imagen más

detallada (ver pág. 113 para cambiar la configuración).

NOTA: Para la configuración automática del modo

de imagen DIA/NOCHE, ver pág. 127.

쐏 Botón de PAUSA

Presione el botón de PAUSA para congelar la imagen.

Presione el botón EXIT para descongelar la imagen.

Presione el botón de PAUSA repetidamente para

pasar através de los tres modos diferentes de

congelamiento (FREEZE) (ver pág. 103).

Como Utilizar el Control Remoto de su TV

El Control Remoto

Como Utilizar el Control Remoto de su TV

El Control Remoto

Como Utilizar el Control Remoto de su TV

16:9 ESTÁNDAR 2

Use este modo de aspecto para desplegar fuentes

16:9 como HDTV y DVD’s conservando la relación de

aspecto original 16:9 mostrando el 100% del tamaño.

Botón de ASPECTO (ASPECT)

Presione este botón para cambiar rápidamente la relación de aspecto del formato de la imagen. Dependiendo

del formato de la señal de entrada recibida, la relación de aspecto del formato de imagen le permite a usted ajustar

• Canal de Antena-Analógica

• Entrada S-Video/Video

(Formato Automático: Off)

• Entrada HDMI- 480i/480p

(Formato Automático: Off)

• Entrada Componente- 480i/480p

(Formato Automático: Off)

• Canal de Antena-Digital (4:3)

• S-Video/Video 4:3/Entrada

Letter (Formato Automático: On)

• HDMI-480i/480p 4:3/Entrada

Letter (Formato Automático: On)

• Componente-480i/480p 4:3/

Entrada Letter

(Formato Automático: On)

• Entrada S-Video/Video 16:9

(Formato Automático: On)

• Entrada 16:9 HDMI- 480i/480p

(Formato Automático: On)

• Entrada 16:9 Componente-

480i/480p

(Formato Automático: On)

• Canal de Antena-Digital (16:9)

• Entrada HDMI- 720p/1080i/1080p

• Entrada Componente-720p/

1080i

NOTA: 1. El modo de Aspecto en todas las entradas de video tienen configuración independiente.

2. Los ajustes de Posición Vertical están disponibles directamente cuando usted elige los modos de aspecto

4:3 EXPANDIDO/ZOOM1/ZOOM2 ó 16:9 ZOOM (ver también pág.115).

4:3 ESTÁNDAR

Use este modo de aspecto para desplegar imágenes

(4:3) convencionales. Se colocan paneles laterales

(áreas grises) en la izquierda yderecha de la imagen

para conservar la relación de aspecto original de la fuente.

Nota: Use este modo por solo el 15% de su tiempo total

de visualización para prevenir envejecimiento desigual

de los fósforos. Los fósforos en el área iluminada de la

imagen envejecerán más pronto que los de las áreas grises

4:3 EXPANDIDO

Use este modo de aspecto para desplegar imágenes

(4:3) convencionales incrementando linealmente la

expansión de la imagen del centro hacia las orillas del

área de despliegue con el próposito de llenarla.

4:3 ZOOM1/ZOOM2

Use estos modos de aspecto para aumentar las

imágenes de fuentes (4:3) convencionales.

16:9 ESTÁNDAR 1

Use este modo de aspecto para desplegar fuentes

16:9 como HDTV y DVD’s conservando la relación de

aspecto original 16:9 mostrando el 95% del tamaño.

16:9 ZOOM

Use este modo para aumentar la imagen en el

aspecto 16:9.

16:9 ZOOM

16:9 ESTÁNDAR1

4:3 ZOOM2

3. Cuando se despliegue el modo 16:9 ESTÁNDAR 2, pueden aparecer líneas en las orillas de la imagen,

considere que esto es una operación normal del televisor.

IMAGEN DE ENTRADA

las imágenes através de las siguientes opciones:

4:3 ESTÁNDAR

:3 ZOOM1

16:9 ESTÁNDAR1 16:9 ZOOM

4:3 ESTÁNDAR

4:3 EXPANDIDO

4:3 ZOOM2 4:3 ZOOM1

16:9 ESTÁNDAR1 16:9 ESTÁNDAR2

4:3 EXPANDIDO 16:9 ZOOM

Nota : Favor de ver el apéndice A

en la página 153-154.

Nota : Favor de ver el apéndice A

en la página 153-154.

Nota : Favor de ver el apéndice A

en la página 153-154.

Nota : Favor de ver el apéndice A

en la página 153-154.

쐂

Como Utilizar el Control Remoto de su TVComo Utilizar el Control Remoto de su TV

El Control Remoto

Botón MENU

El botón MENU desplegará el Menú en Pantalla.

Botón EXIT

Este botón lo sacará de todos los menús en pantalla.

쐆

쐎

쐊

Botón de entradas (INPUTS)

Cuando el control remoto está en el modo TV, presione

este botón para accesar al menú de ENTRADAS.

Use los CURSORES y el botón SELECT para elegir

las entradas que están siendo usadas. El presionar

repetidamente el botón de ENTRADAS lo llevará

através de todas las opciones del menú de entradas.

Luego presione el botón SELECT para seleccionar.

HDMI-Frontal

Fotos

Entrada 2

Aérea / Cable

MoverSEL Elegir

Entrada 1

AEREA/CABLE Seleccione entre la señal Aérea o de Cable.

Botones CURSOR/SELECT

Todas las funciones del Menú en pantalla pueden ser

configurados o ajustados utilizando los CURSORES,

excepto los valores númericos. Los CURSORES

resaltarán, ajustarán y configurarán diversas funciones.

Presione el CURSOR de la dirección deseada y

쐅

쐈

쐉

Botón PICTURE-IN-PICTURE (PIP)

Vea la sección separada en las páginas 33-34 para

una descripción más detallada.

Presione este botón para desplegar los subtítulos

en la pantalla cuando estén disponibles por el

Botón de GUIA (GUIDE)

[Solo modos Receptor de Cable (CBL),

receptor satelital (SAT)/Set-Top-Box (STB)]

Presione este botón para accesar la Guía de Canales

del cable (CBL) y receptor satelital o alta definición

(SAT/STB) en el modo (CBL)(SAT/STB).

programa de TV. En Canales Analógicos, presione

el botón CC una y otra vez, para ir através de los

modos de Subtítulos y para desactivar los Subtítulos.

씈

FOTOS Seleccione para accesar sus fotos de una

unidad SD/MMC o tarjeta de memoria

SD/MMC que este conectada en la entrada

de Fotos frontal de la TV Plasma (ver

Botón INFO

Presione este botón cuando usted desee consultar

el canal recibido, el origen o fuente de la imagen,

si el canal tiene estereo (ST) o programa secundario

de audio (SAP), la hora, el nombre del canal

o si el tiempo de auto apagado está activado.

씉

presione el botón SELECT para seleccionar o elegir.

Botón de Subtítulos (Closed Captions-CC)

ENTRADA2

Seleccione para ir a la Entrada 2.

ENTRADA3

Seleccione para ir a la Entrada 3.

ENTRADA-FRONTAL

Seleccione para ir a la Entrada Frontal.

HDMI1

Seleccione para ir a la entrada HDMI 1.

HDMI-FRONTAL

Seleccione para ir a la entrada HDMI Frontal.

ENTRADA1

Seleccione para ir a la Entrada 1.

HDMI2

Seleccione para ir a la entrada HDMI 2.

págs. 99-100).

S-IN: 1

480i 3:17PM

Auto

CANALES DIGITALES

Subtítulos Digitales

Este ícono aparecerá solamente cuando

se reciba una transmisión Digital que incluya Subtítulos.

Show Name Air 8

3:00PM- 3:30PM KXYZ-HD

ST TV-G 480i 3:17PM

Auto STEREO

Duración del programa

Información del programa

Clasificación

del programa

Formato de la Imagen

Tipo de

Audio

Fuente Imagen

Principal y # de canal

Identificación de

canal transmitido

Reloj

Configuración

de Subtítulos

Selección de

Fuente de Audio

CANALESANALOGICOS

Show Name Air 15-1

3:00PM-

3:30PM KPBS-HD

ST 1080i 3:17PM

Auto

Duración del programa

Información del programa

Clasificación

del programa

Formato de la Imagen

Tipo de

Audio

Fuente Imagen

Principal y # de canal

Identificación de

canal transmitido

Reloj

Configuración

de Subtítulos

DTvCC TV-G

ALT U.S.

Clasificación

Región 5

Descripción del programa

(Presione INFO otra vez para una información

Cuando se conecta Video Componente:

Señal Y-PbPr conectada a la ENTRADA 3

Formato de la

Señal de entrada

Y-PBPR: 3

480i 3:17PM

Auto

Cuando se conecta una señal S-VIDEO

a la ENTRADA 1

más detallada)

NOTA: 1. Presionar el botón INFO otra vez ó el botón

EXIT pare regresar al la imagen normal.

2. La configuración del Aspecto no será

mostrada si el canal está bloqueado.

Evento programado

10:00 AM

Evento programado

Y-PBPR: 3

480i 3:17PM

Auto

Como Utilizar el Control Remoto de su TV

No. 02/08

06/13/05

2048x1536

DSC00467

1. Presione el botón de ENTRADAS (INPUTS)

para navegar através de las diferentes

ENTRADAS hasta seleccionar FOTOS. Luego,

presione el botón SELECT o el CURSOR .

2. Presione los CURSORES  o  para accesar

a la foto siguiente o a la foto anterior.

3. Presione el botón SELECT para ver las muestras.

4. Use los CURSORES ,, o  y seleccione

el botón SELECT para navegar y seleccionar

individualmente las fotos de su elección.

5. Presione el número de fotografía para saltar de

imagen a imagen.

6. Presione el botón INFO para accesar al menú

de FOTOS y ver la información de la fotografía.

7. Presione los CURSORES  o  y el botón

SELECT para navegar y seleccionar el menú

de FOTOS.

FOTOS

Esta función es útil para ver imágenes digitales fijas de su unidad SD o tarjeta de memoria SD usando la

entrada de Fotos en el panel frontal de su televisor.

HDMI 1

HDMI- Frontal

Fotos

Entrada 1

Mover SEL Elegir

Aérea/Cable

SEL Muestra [0-9] Saltar

Elegir Número

de Fotografía

NOTAS:1.El Contraste disminuirá automáticamente si se dejan en la pantalla imágenes estacionarias tales

como fotos digitales por más de tres minutos.

2.El número máximo de fotos digitales que pueden ser desplegadas es de 999.

3. Presione el botón INFO para mostrar los números de fotos en tamaño muestra, además de otra

información de las fotos individuales.

No. 02/08

06/13/05

2048x1536

DSC00467

Rotar

Presentación

Número de Foto

Fecha

Resolución

Nombre del Archivo

Como Utilizar el Control Remoto de su TV

El Control Remoto

100

test-bleed 3/3/06 10:18 AM Page 102

Como Utilizar el Control Remoto de su TV

El Control Remoto

Como Utilizar el Control Remoto de su TV

ROTAR

Seleccione esta opción del menú para rotar las fotos en

dirección de las manecillas del reloj (CURSOR ) y en

dirección inversa a las manecillas del reloj (CURSOR ).

PRESENTACIÓN

Seleccione esta opción del menú para iniciar una

presentación de las fotos digitales. Mientras el submenú

del Intervalo está resaltado, presione el botón SELECT

para cambiar el tiempo de intervalo desde 5, 10 y 30

segs. Presione el botón SELECT para parar en una foto

elegida de la presentación. Despúes de 30 segundos,

la presentación continuará o presione el botón

SELECT otra vez para continuar con la presentación.

Rotar

Presentación Iniciar

Intervalo 5seg

NOTAS: 1. Durante la PRESENTACIÓN también funciona la Reducción Automática de contraste, para continuar

presione luego cualquier botón

2. Los nombres modificados de los archivos de fotos deben ser de 8 caracteres (Ej. ABCD1234.jpg).

1er. caracter: letras; 2do al 4to: letras o números; 5to al 8vo.: números. Los archivos de fotos deben

er colocados primeramente en el nombre de un subdirectorio con 8 caracteres (Ej. 123ABCDE). 1er al

3ro: números; 4to al 8vo.: letras. El subdirectorio luego debe ser colocado en un directorio principal

con un nombre de archivo de formato “dcim” .

3. Los tipos de imágenes soportadas son de hasta 3072 x 2304; el formato JPEG deberá estar conforme

con el Estándar DCF (Regla de Diseño para el Sistema de Archivos de Cámara).

4. Este televisor despliega solamente imágenes digitales de cámaras digitales que cumplen el estándar DCF.

Las Imágenes que son copiadas, editadas o modificadas en una computadora pueden ser no

desplegadas en el televisor.

Como Utilizar el Control Remoto de su TV

Rotar

101

test-bleed 3/3/06 10:18 AM Page 103

El Control Remoto

씋

Cable 6

FAV Cable 6

Cable 6

Volume 8

Soft Mute 8

Mute 8

씊

Como Utilizar el Control Remoto de su TV

Botón de VOLUMEN (VOL), Botón MUTE

Use el botón VOL UP () or VOL DOWN () hasta

obtener el nivel de sonido deseado.

Para reducir el sonido a la mitad del volumen normal

(SOFT MUTE) para contestar el teléfono, etc., presione

el botón MUTE. Presione el botón MUTE un vez más

para apagar el sonido completamente (MUTE). Para

encender el sonido, presione el botón MUTE una vez

más o el botón VOL UP().

Los Subtítulos serán desplegados automáticamente

cuando las funciones MUTE/SOFT MUTE estén activas

y los Subtítulos estén en modo AUTO (ver pág. 132).

Cuando el televisor sea apagado a un nivel de volumen

de 31 o más, el nivel de volumen por default será de

30 cuando el televisor sea encendido. Sin embargo, si

el nivel está en 30 o menos, este nivel de volumen se

mantendrá cuando el televisor sea encendido.

Botones del SELECTOR DE CANAL/ CANALES

Los botones del SELECTOR DE CANALES son

usados para seleccionar canales, ingresar código de

CANALES para ingresar uno, dos, o tres números para

acceso, etc. Use los botones del SELECTOR DE

seleccionar los canales. Ingrese primero el número

“0” para canales del 1 al 9, o simplemente presione

el único dígito del canal que se desea sintonizar y

presione el botón ENTER para que la TV lo

sintonice. Para Canales Digitales, use los botones

del SELECTOR DE CANALES con el botón del

GUIÓN (-). La selección de canales también puede ser

realizada con el botón CH UP (

) o CH DOWN ( ).

Botón de GUIÓN (-)

Use el botón de GUIÓN (-) junto con los de

SELECCIÓN DE CANALES para sintonizar Canales

Digitales que tienen números de subcanal indicados

con un (-) GUIÓN (ejemplo: 15-1).

Botón de GRABACIÓN (RECORD)

Presione este botón para grabar programas cuando

el control remoto está en modo PVR/VCR.

FAVORITOS (FAV CH) y ENTER.

Presione el botón CANALES FAVORITOS (FAV CH)

para cambiar al modo de canal favorito (FAV). Usted sabrá

cuando está en el modo de Canal Favorito cuando (FAV)

es desplegado y el # de canal desplegado está VERDE.

Presione otra vez para regresar y sintonizar a sus canales

regulares. Usted puede agregar cualquier canal a su Lista de

Canales Favoritos presionando y manteniendo presionado

el botón FAV CH hasta que el # de canal desplegado

cambie de BLANCO a VERDE RESALTADO. Tambié n

puede borrar un canal de su lista de canales favoritos

presionando y manteniendo presionado el botón FAV CH

hasta que el # de canal desplegado cambie de VERDE

RESALTADO a BLANCO.

Presione este botón para cambiar entre el canal

actual y el último canal visto.

Botón de ÚLTIMO CANAL (LAST CH)

Como Utilizar el Control Remoto de su TV

El Control Remoto

Picture-In-Picture (PIP)

102

햲

NOTA: 1. En el modo PIP SPLIT, presione los CURSORES ( t o u ) para habilitar el sonido de la subimagen.

CABLE

AEREA

SALIDA

VCR

VIDEO AUDIO

Su televisor Plasma HITACHI tiene incorporada una

tecnología de sintonizador diseñada para obtener una

imagen mejorada que usted disfrutará. Esta función

le permite poder ver simultáneamente Canales Digitales

y Entradas de Video tanto en la imagen principal como

sub-imagen con un control separado. Los Canales

Analógicos no pueden ser vistos en el modo PIP. Para

la disponibilidad en el modo PIP, favor de ver la tabla

Para seleccionar entre la imagen principal y la sub-imagen

PIP use los CURSORES del control remoto. El canal

con despliegue de color verde se moverá con cada presión

de los CURSORES.

La función PIP (Picture-in-Picture) es conveniente cuando

usted desea ver más de un programa al mismo tiempo.

Usted puede ver un programa de TV mientras ve otros

programas de cualquiera de las entradas de video.

Use la conexión que se muestra a la derecha para

ver un programa de VCR como sub-imagen mientras

ve otro en la imagen principal (Canal Digital de

햲Botón PIP

Presione el botón PIP y aparecerá una sub-imagen

en el modo SPLIT. Presione el botón EXIT

para regresar a la vista normal.

SWAP

Imagen Principal

Sub-Imagen

en la parte de abajo.

señal CABLE/AEREA ).

Parte trasera

de VCR

Tabla de especificaciones del PIP

Canal Digital

1080i 720p 480p 480p 480i 480i 1080i 720p 480p 480p 480i 480i

16x9 16x9 16x9 4x3 16x9 4x3 16x9

1080p(*)

16x9 16x9 16x9 4x3 16x9 4x3

Componente

Compuesto

S-IN

HDMI

Canal Digital

(Aéreo o Cable)

Sub Imagent

Imagen Principal

Componente/Compuesto/S-lN/HDMI

DIVIDIDO

(SPLIT)

PIP

Modo

1080i 16x9

------

720p 16x9

------

480p 16x9

------

480p 4x3

- - - - - -

480i 16x9

------

480i 4x3

- - - - - -

1080i 16x9

720p 16x9

480p 16x9

480p 4x3

Sí Sí Sí Sí Sí Sí

1080p (*) 16x9

Sí Sí Sí Sí Sí Sí

480i 16x9

480i 4x3

Sí Sí Sí Sí Sí Sí

----- -

- - - - - -

Sí Sí Sí Sí Sí Sí

Sí

Sí

Sí

Sí

*) Solo entrada HDMI

test-bleed 3/3/06 10:18 AM Page 33

El Control Remoto

Picture-In-Picture (PIP)

103

IMAGEN PRINCIPAL CONGELADA

Presione el botón PAUSE para congelar un cuadro

de la imagen que usted está viendo, el cuadro

congelado será mostrado en la imagen principal.

Presione el botón EXIT para regresar a la vista normal.

Esta función es útil para congelar cuadros de imagen

햳Botón de PAUSA (PAUSE)

Presione el botón PAUSE repetidamente para

cambiar entre modos de congelamiento (FREEZE)

(Freeze principal, modo dividido y modo por pasos).

Esta función es conveniente cuando se desea escribir

la dirección de una compañía de orden por correo

tomar estadísticas de algún evento deportivo, etc.

Para volver a la imagen en movimiento, presione el

botón EXIT

햳

Hot Springs Clay Mask

C/O John Doe

Run-Spa Retreat

P.O. Box 55512

Any Town, USA 98765

Check or

Money Order Only

1-800-555-1212

IMAGEN CONGELADA DIVIDIDA

Presione el botón PAUSE para congelar la imagen

que usted está viendo (solamente la sub-imagen

derecha se congelará). Presione el botón EXIT

para regresar a la vista normal.

Imagen Principal

Sub-imagen

que contienen datos de direcciones o teléfonos.

NOTA: 1. El modo FREEZE predeterminado es imagen

PRINCIPAL congelada, seguido de imagen

congelada DIVIDIDA y después por PASOS. El

último modo de FREEZE que se seleccionó antes

de presionar el botón EXIT será el que aparezca

al presionar el botón PAUSE de nuevo.

2. Cada cuadro de imagen congelado en el modo

por pasos está retardado 0.1 (1/10) segundos.

(MAIN FREEZE)

(SPLIT FREEZE)

IMAGEN CONGELADA POR PASOS

Presione el botón PAUSE para congelar tres cuadros

de la imagen que usted está viendo (solamente

3 sub-imágenes se congelarán). Presione el

botón EXIT para regresar a la vista normal. Esta

función es útil para ver imágenes en movimiento

que tienen muchos detalles, por ejemplo, una jugada

de cerca en un evento deportivo o en un tiro de golf.

(STROBE FREEZE)

El Control Remoto para controlar un receptor de Cable

햲

햳

햲

햳

햲

햳

햲

OPERACION DE LAS FUNCIONES PREGRABADAS

104

El Control Remoto

PARA SU RECEPTOR DE CABLE.

Este control remoto está diseñado para operar diferentes tipos

de receptores de cable. Usted debe primero programar el

control remoto para ser compatible con el sistema remoto de su

receptor de cable (consulte las páginas 109-110 para ver la

1. Encienda su receptor de cable.

2. Para cambiar al modo de Cable (CBL), utilice el botón

SOURCE SELECT en el control remoto para posicionar la

la luz del LED en la selección correspondiente SAT/CBL.

3. Mantenga presionado el botón SOURCE SELECT en el

remoto e ingrese el código de cuatro dígitos preestablecido

que coincide con su receptor, como se muestra en las

páginas 109-110. Suelte el botón SOURCE SELECT. La luz

indicadora parpadeará tres veces si el código fue aceptado.

4. Apunte el control remoto hacia el receptor de cable y presione el

botón POWER. El control apagará su receptor de cable

cuando ingrese el código preestablecido de cuatro dígitos

correcto. Cuando esto ocurre, el control remoto ya está

programado para su receptor. Si su receptor no se apaga,

intente un código de cuatro dígitos preestablecido diferente.

5. El control remoto ahora controlará su receptor de cable.

NOTA: 1. Si su receptor no puede ser operado después

de realizar los procedimientos anteriores, el

código de su receptor no ha sido pregrabado

en el control remoto.

2. En el caso improbable de que su receptor

no pueda ser operado después de realizar

los procedimientos anteriores, por favor

consulte su guía de operación del receptor.

3. El control remoto recordará los códigos que

usted haya programado hasta que se remuevan

las baterías del control remoto. Después de

reemplazar las baterías, repita el procedimiento

completo de programación como se describe

arriba.

햲 Botones PREGRABADOS DEL RECEPTOR

Estos botones transmiten los códigos pregrabados

al receptor de cable programado.

햳 Botones EXCLUSIVOS DE TV

Estos botones son para operar solamente el TV.

EL CÓDIGO DE MI RECEPTOR DE CABLE

NOTA: Consulte la guía de operación del receptor de cable

para la operación de los botones exclusivos para el

receptor de cable.

lista de códigos).

ES:

105

test-bleed 3/3/06 10:18 AM Page 35

El Control Remoto para controlar un STB*/Receptor Satelital

햲

햳

햲

햳

햲

햳

햲

El Control Remoto

OPERACION DE LAS FUNCIONES PREGRABADAS

PARA SU STB/RECEPTOR SATELITAL.

Este control remoto está diseñado para operar diferentes tipos

de STB/receptores satelitales. Usted debe primero programar

el control remoto para ser compatible con el sistema remoto

de su receptor de satélite (consulte las páginas 109-110 para ver

1. Encienda su STB/Receptor Satelital.

2. Para cambiar al modo de STB/Receptor Satelital (SAT),

utilice el botón SOURCE SELECT en el control remoto para

posicionar la luz del LED en la selección correspondiente

3. Mantenga presionado el botón SOURCE SELECT en el

remoto e ingrese el código de cuatro dígitos preestablecido

que coincide con su STB/receptor Satelital, como se muestra en

las páginas 109-110. Suelte el botón SOURCE SELECT. La

luz indicadora parpadeará tres veces si el código fue aceptado.

4. Apunte el control remoto hacia el STB/receptor Satelital y

presione el botón POWER. El control apagará su STB/

receptor Satelital cuando ingrese el código preestablecido de

cuatro dígitos correcto. Cuando esto ocurre, el control remoto ya

está programado para su STB/receptor Satelital. Si su STB/

receptor Satelital no se apaga, intente un código de cuatro

5. El control remoto ahora controlará su receptor de cable.

la lista de códigos).

SAT/CBL .

dígitos preestablecido diferente.

NOTA: 1. Si su STB/Receptor Satelital no puede ser

operado después de realizar los procedimientos

anteriores, el código de su STB/Receptor

Satelital no ha sido pregrabado en el control remoto.

2. En el caso improbable de que su convertidor

no pueda ser operado después de realizar

los procedimientos anteriores, por favor

consulte su guía de operación del convertidor.

3. El control remoto recordará los códigos que

usted haya programado hasta que se remuevan

las baterías del control remoto. Después de

reemplazar las baterías, repita el procedimiento

completo de programación como se describe

arriba.

햲 Botones PREGRABADOS DEL STB/RECEPTOR

Estos botones transmiten los códigos pregrabados

al STB/Receptor Satelital programado.

햳 Botones EXCLUSIVOS DE TV

Estos botones son para operar solamente el TV.

EL CÓDIGO DE MI STB/RECEPTOR SATELITAL

NOTA: Consulte la guía de operación del STB/Receptor

Satelital para la operación de los botones

exclusivos para el STB/Receptor Satelital.

ES:

SATELITAL).

*STB: Set-Top-Box (Receptor de señal de alta definición).

test-bleed 3/3/06 10:18 AM Page 36

El Control Remoto para controlar un reproductor de DVD

햲

햳

햲

햳

햲

햳

햲

El Control Remoto

OPERACION DE LAS FUNCIONES PREGRABADAS

106

PARA SU REPRODUCTOR DE DVD.

Este control remoto está diseñado para operar diferentes tipos

de reproductores de DVD. Usted debe primero programar el

control remoto para ser compatible con el sistema remoto de

su reproductor de DVD (consulte las páginas 109-110 para ver la

1. Encienda su reproductor de DVD.

2. Para cambiar al modo de DVD (DVD), utilice el botón

SOURCE SELECT en el control remoto para posicionar la

la luz del LED en la selección correspondiente DVD.

. Mantenga presionado el botón SOURCE SELECT en el

remoto e ingrese el código de cuatro dígitos preestablecido

que coincide con su reproductor de DVD, como se muestra en

las páginas 109-110. Suelte el botón SOURCE SELECT. La

luz indicadora parpadeará tres veces si el código fue aceptado.

4. Apunte el control remoto hacia el reproductor de DVD y

presione el botón POWER. El control apagará su reproductor

de DVD cuando ingrese el código preestablecido de cuatro

dígitos correcto. Cuando esto ocurre, el control remoto ya

está programado para su reproductor de DVD. Si su reproductor

de DVD no se apaga, intente un código de cuatro dígitos

5. El control remoto ahora controlará su reproductor de DVD.

lista de códigos).

preestablecido diferente.

NOTA: Consulte la guía de operación del reproductor de DVD

para la operación de los botones exclusivos para el

reproductor de DVD.

NOTA: 1. Si su reproductor de DVD no puede ser

operado después de realizar los procedimientos

anteriores, el código de su reproductor de DVD

no ha sido pregrabado en el control remoto.

2. En el caso improbable de que su reproductor

de DVD no pueda ser operado después de

realizar los procedimientos anteriores, por favor

consulte su guía de operación del reproductor.

3. El control remoto recordará los códigos que

usted haya programado hasta que se remuevan

las baterías del control remoto. Después de

reemplazar las baterías, repita el procedimiento

completo de programación como se describe

arriba.

햲 Botones PREGRABADOS DEL

Estos botones transmiten los códigos pregrabados

al reproductor de DVD programado.

햳 Botones EXCLUSIVOS DE TV

Estos botones son para operar solamente el TV.

EL CÓDIGO DE MI REPRODUCTOR DE DVD

ES:

REPRODUCTOR DE DVD.

107

test-bleed 3/3/06 10:18 AM Page 37

El Control Remoto para controlar una VCR/PVR

OPERACION DE LAS FUNCIONES PREGRABADAS

햲

햳

햲

햳

햲

햳

햲

El Control Remoto

DE SU VCR/PVR (Videograbadora personal).

Este control remoto está diseñado para operar diferentes tipos

de VCRs/PVRs. Usted debe primero programar el

control remoto para ser compatible con el sistema remoto de su

VCR/PVR (consulte las páginas 109-110 para ver la lista de

1. Encienda su VCR/PVR.

2. Para cambiar al modo de VCR/PVR (PVR/VCR), utilice

el botón de SOURCE SELECT en el control remoto para

posicionar la luz del LED en la selección correspondiente

3. Mantenga presionado el botón SOURCE SELECT en el

remoto e ingrese el código de cuatro dígitos preestablecido

que coincide con su VCR/PVR, como se muestra en las

páginas 109-110. Suelte el botón SOURCE SELECT. La luz

indicadora parpadeará tres veces si el código fue aceptado.

4. Apunte el control remoto hacia el VCR/PVR y presione

el botón POWER. El control apagará su VCR/PVR

cuando ingrese el código preestablecido de cuatro dígitos

correcto. Cuando esto ocurre, el control remoto ya está

programado para su VCR/PVR. Si su VCR/PVR no se apaga,

intente un código de cuatro dígitos preestablecido diferente.

5. El control remoto ahora controlará su VCR/PVR.

NOTA: 1. Si su

VCR/PVR no puede ser operado

después de realizar los procedimientos

anteriores, el código de su VCR/PVR

no ha sido pregrabado en el control remoto.

2. En el caso improbable de que su VCR/PVR

no pueda ser operado después de realizar

los procedimientos anteriores, por favor

consulte su guía de operación del VCR/PVR.

3. El control remoto recordará los códigos que

usted haya programado hasta que se remuevan

las baterías del control remoto. Después de

reemplazar las baterías, repita el procedimiento

completo de programación como se describe

arriba.

햲 Botones PREGRABADOS DEL VCR/PVR

Estos botones transmiten los códigos pregrabados

al VCR/PVR programado.

햳 Botones EXCLUSIVOS DE TV

Estos botones son para operar solamente el TV.

EL CÓDIGO DE MI VCR/PVR ES:

NOTA: Consulte la guía de operación del VCR/PVR

para la operación de los botones exclusivos

para el VCR/PVR.

códigos).

PVR/VCR.

test-bleed 3/3/06 10:18 AM Page 40

Como utilizar el botón SOURCE SELECT

108

HDMI- FRONT 7

NUMERO ASIGNADO

ENTRADA

Tabla 1

HDMI 2 6

HDMI 1 5

VIDEO- FRONT 4

VIDEO 3 3

VIDEO 2 2

VIDEO 1 1

El Control Remoto

ACCESO A LAS ENTRADAS

Esta función opcional permite al usuario del control

remoto, la configuración de su botón SOURCE SELECT

para accesar una entrada específica de la TV. La

configuración para esta función solamente es aplicable al

modo normal del control remoto y solamente es aplicable

a los modos de DVD, PVR/VCR y SAT/CBL.

1. Seleccione el modo del dispositivo deseado (DVD,

PVR/VCR o SAT/CBL) utilizando el botón de SOURCE

selección correspondiente.

2. Mantenga presionado el botón de SOURCE SELECT

en el control remoto e ingrese el código de cuatro

dígitos preestablecido que sea compatible con su

3. Luego, ingrese el número de entrada (1-7) relacionado

a donde fue conectado el dispositivo (ver tabla 1).

4. Suelte el botón de SOURCE SELECT.

5. Si se realizó correctamente, el indicador LED

del

dispositivo parpadeará 3 veces para confirmar una

6. El control remoto ahora controlará el dispositivo deseado.

7. Presionando el botón INPUTS, se accessará a la

entrada de video del dispositivo deseado.

EJEMPLO DE CONFIGURACIÓN (DVD Hitachi con código

de lista 0573 conectado a la entrada 1 de la TV).

 Seleccione el modo DVD utilizando el botón de

SOURCE SELECT para posicionar el indicador

LED en DVD.

 Mantenga presionado el botón SOURCE SELECT

y presione los números 0, 5, 7 y 3.

 Luego presione el número 1, que representa el

número de entrada asignada al reproductor de DVD.

 Suelte el botón SOURCE SELECT.

 Si se realizó correctamente, el indicador LED del

dispositivo parpadeará 3 veces para confirmar una

 El control remoto ahora controlará el reproductor de DVD.

 Presione el botón INPUTS para accesar

instantáneamente a la entrada de video de su DVD

NOTA: 1. Esta función es opcional.

2. Si aplica, los números de entrada asignados

pueden ser usados más de una vez.

SELECT para posicionar el indicador LED en la

dispositivo como se muestra en las páginas 109-110.

correcta configuración.

en la entrada 1.



, , 







, , 

109

test-bleed 3/3/06 10:18 AM Page 41

Códigos del Control Remoto

Marca CABLE Códigos General Instrument ........0869 Daewoo .........................0045, 0278, 0020,0561 1479