Balt 91779-XXXX-XX Assembly Instructions

Tipo
Assembly Instructions
Single Pedestal Teachers Desk
UPDATED AS OF: 12/02/2021
91774, 91775, 91776, 91777-XXXX-XX
1 of 8
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
LEFT HANDED
RIGHT HANDED
Parts
UPDATED AS OF: 12/02/2021 2 of 8
P1 - Table Top
P2 - Modesty Panel
P3 - Front Leg
P4 - Back Leg
P5 - Pedestal Box
P5A - Handle
P5B - Divider Panel
P5C - Divider Bar
P5D - Pencil Tray
P5E - Key Set
x1
x1
x1
x1
x1
x3
x1
x1
x1
x1
A - Leg Panel Screw
(1/4-20 x 75mm)
B - Ped. Panel Screw
(M6 x 12mm)
C - Ped. Wood Screw
(#12 x 1”)
D - Leg Wood Screw
(#10 x 1”)
E - Pedestal Casters
E1 - Locking
E2 - Non-Locking
F - Leg Casters
F1 - Locking
F2 - Non-Locking
G - Lock Washer
H - Plastic Side Cap
I - Ped. Caster Screw
(M4 x 12mm Tap)
J - Plastic Back Cap
(NOT USED)
x2
x2
x5
x14
x2
x2
x1
x1
x2
x8
x4
x6
Hardware
Tool(s):
-Allen Wrench
-Caster Wrench
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
UPDATED AS OF: 12/02/2021 3 of 8
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
complètes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient serrées.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a laide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 12/02/2021 4 of
STEP 2
Open shelves and remove handle screws. Swap handles to front of shelves and insert
handle screws from inside of shelves to secure handles in place.
Remove shelves by first extending shelf to furthest setting until catch engages. To slide
shelf off of rails, rotate visible catch levers on both sides of shelf either up or down while
gently pulling shelf. Once both sides are free, shelf can be removed.
STEP 3
UPDATED AS OF: 12/02/2021 5 of 8
STEP 4
Set pedestal (with shelves removed) upside down on top. Secure to top with wood screws
inserted through holes in pedestal top brackets. (Left handed desk depicted, pre-drilled
holes for pedestal will be on opposite end of top for right handed desks).
NO SCREWS
FRONT
INSIDE
FRONT
Set Back Leg on Top and using pre-drilled holes as a guide for placement, screw to top
with six wood screws. Two holes in mounting plate will not receive screws (See graphic).
NO SCREWS
FRONT
INSIDE
LEFT HANDED DESK: RIGHT HANDED DESK:
FRONT
P4
C
D
STEP 5
UPDATED AS OF: 12/02/2021 6 of 8
STEP 6
Install Modesty Panel using two screws through Back Leg and two screws within pedestal.
Screw Front Leg to Top using eight wood screws.
P2
AB
P3
D
STEP 7
UPDATED AS OF: 12/02/2021 7 of 8
STEP 8
Install Casters to bottom of pedestal. Use Locking Casters in front of pedestal and
Non-Locking Casters in the back. Secure casters with screws.
Screw casters with Lock Washers into legs. Install Locking Caster in front and Non-
Locking Caster in back. Tighten with Caster Wrench.
F1
F2
I
E1
E2
G
STEP 8
Install Casters to bottom of pedestal. Use Locking Casters in front of pedestal and
Non-Locking Casters in the back. Secure casters with screws.
STEP 9
Insert shelves back into pedestal box and place accessories as desired within shelves.
THIS COMPLETES ASSEMBLY INSTRUCTION
UPDATED AS OF: 12/02/2021 8 of 8
STEP 10
With at least two people, carefully flip desk upright. Push in Plastic Caps into inserts
on either side of pedestal.
H
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Balt 91779-XXXX-XX Assembly Instructions

Tipo
Assembly Instructions

En otros idiomas