Instructor Teacher’s Desk
UPDATED AS OF: 05/07/2021
Part Numbers: 91785-XXXX-XX, 91786-XXXX-XX
1 of 9
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
Parts
UPDATED AS OF: 05/07/2021 2 of 9
P1 - Table Top
P2 - Leg Panel A
P3 - Leg Panel B
P4 - Back Panel
P5 - Leg Post
P6 - Crossbar
P7 - Pedestal Box
P7A - Handle
P7B - Divider Panel
P7C - Divider Bar
P7D - Pencil Tray
P7E - Key Set
x1
x1
x1
x1
x1
x1
x1
x3
x1
x1
x1
x1
A - Wood Screw
(#10 x 1.75”)
B - Machine Screw
(M6 x 12mm)
C - Ped. Wood Screw
(#12 x 1”)
D - Ped. Caster Screw
(M4 x 12mm Tap)
E - Pedestal Casters
E1 - Locking
E2 - Non-Locking
F - Leg Casters
F1 - Locking
F2 - Non-Locking
G - Lock Washer
H - Plastic Side Cap
I - Plastic Back Cap
Tool(s):
-Allen Wrench
-Caster Wrench
x6
x12
x5
x4
x2
x2
x2
x1
x3
x8
x6
Hardware
For full product warranty details, please visit:
Para obtener información sobre la garantía del producto, consulte este sitio (ingles):
Pour plus d’informations sur la garantie du produit, consultez ce site (anglais):
For questions on assembly or missing/damaged parts, please contact us using the
following information.
Para preguntas sobre el ensamblaje o piezas faltantes o dañadas, por favor
contáctenos usando la siguiente información.
Pour toute question sur le montage l-assamblage manquantes ou endommagées,
veuillez nous contacter en utilisant les l’information ci-dessous.
To register your product for warranty, please visit:
Para registrar la garantía del producto, vea este sitio (en ingles):
Pour enregistrer la garantie de votre produit, consultez ce site (en anglais):
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
WARRANTY
CARE & MAINTENANCE
PRODUCT REGISTRATION
UPDATED AS OF: 05/07/2021 3 of 9
Phone:
1.800.749.2258
(Monday – Friday, 8AM – 5PM
Central Time)
http://moorecoinc.com/warranty
https://moorecoinc.com/register
Email:
support@moorecoinc.com
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
complètes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient serrées.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 05/07/2021 4 of 9
STEP 2
Open shelves and remove handle screws. Swap handles to front of shelves and insert
handle screws from inside of shelves to secure handles in place.
Remove shelves by first extending shelf to furthest setting until catch engages. To slide
shelf off of rails, rotate visible catch levers on both sides of shelf either up or down while
gently pulling shelf. Once both sides are free, shelf can be removed.
STEP 3A
UPDATED AS OF: 05/07/2021 5 of 9
FOR RIGHT HANDED DESK: Set top on protected surface so that underside is facing
up. Install legs and modesty panel pieces as shown using machine and wood
screws provided. Use pre-drilled holes for proper panel alignment.
(See STEP 3B for Left Handed Desk).
A
P3
P5
P2
B
A
B
A
P4
**NOTE: Must use panel with holes
in location shown
STEP 3B
UPDATED AS OF: 05/07/2021 6 of 9
FOR LEFT HANDED DESK: Set top on protected surface so that underside is facing
up. Install legs and modesty panel pieces as shown using machine and wood
screws provided. Use pre-drilled holes for proper panel alignment.
A
P5
P2
B
B
A
P3
**NOTE: Must use panel with holes
in location shown
B
A
P4
STEP 4
UPDATED AS OF: 05/07/2021 7 of 9
STEP 5
Set empty pedestal box upside down on top in position shown. Secure to panel with two
screws through side inserts. (Instructions that follow depict right handed desk installation.
For left handed desk installation part positions will be mirrored.)
Set Crossbar on top between pedestal and panel. Secure in place with two screws at
each end through pedestal side inserts and panel support.
B
B
P6
STEP 6
UPDATED AS OF: 05/07/2021 8 of 9
STEP 7
Screw pedstal box into top with five wood screws through holes shown.
Insert Pedestal Casters by sliding tabs into slots then locking in place with screws.
Be sure to place locking casters in front and non-locking in back.
C
D
E1
E2
STEP 8
UPDATED AS OF: 05/07/2021 9 of 9
STEP 9
Insert threaded stems on Leg Casters into posts, placing single non-lcoking caster in
the back. Be sure to include a Lock Washer with each and tighten with Caster Wrench.
With at least two people, flip desk upright. Insert shelves back into pedestal box and
place accessories as desired within shelves. (Optional: Insert Plastic Side Caps and
Back Caps into open holes in pedestal.)
THIS COMPLETES ASSEMBLY INSTRUCTION
F1
F2
G
H
I
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
en otros idiomas
- français: Balt 91786 Manuel utilisateur
- English: Balt 91786 User manual
Artículos relacionados
-
Balt 91779-XXXX-XX Assembly Instructions
-
-
-
-
-
-
-
-
-
Otros documentos
-
MooreCo Avid Modular Desk System 91774–91777 Assembly Instructions
-
-
-
-
-
-
-
-
-