Infinity Drain FXAS 6560 BK Guía de instalación

Tipo
Guía de instalación
Fixed Length Series
Installation Instructions
The Fixed Length Series is intended for use with traditional waterproong methods:
°
Hot Mop
°
Copper Pan
°
Rubber Liner (Chloraloy®)
°
PVC Liner
°
Lead Pan
°
Fiberglass
Dimension are subject to Manufacturers tolerance and change without notice. We can assume no responsibility for
use of superseded or void data.
Las dimensiones están sujetos a la tolerancia del fabricante y cambio sin previo aviso. No podemos asumir ninguna
responsabilidad por el uso de datos a sustituir los nulos.
Infinity Drain • 145 Dixon Avenue, Amityville, New York 11701
Phone 516.767.6786 • Fax 516.740.3066 • www.InfinityDrain.com
Made in the U.S.A.
FXED 65
FXDG 65
FXAS 65
FXMN 65 FXIG 65
FXSG 65
FXAS 125
FXTIF 65
FXC CUSTOM
Custom Sizes
Available
2
Series Components:
FXED 65 Series
EA 6532 32SS Grate
EA 6536 36″ SS Grate
EA 6542 42SS Grate
EA 6548 48SS Grate
EA 6560 60″ SS Grate
XC 6532 32SS Fixed Channel
XC 6536 36″ SS Fixed Channel
XC 6542 42SS Fixed Channel
XC 6548 48" SS Fixed Channel
XC 6560 60" SS Fixed Channel
HS 2 2" Hair Strainer
TNAS SS Threaded Nipple
FXMN 65 Series
MA 6532 32SS Grate
MA 6536 36″ SS Grate
MA 6542 42″ SS Grate
MA 6548 48″ SS Grate
MA 6560 60″ SS Grate
XC 6532 32SS Fixed Channel
XC 6536 36″ SS Fixed Channel
XC 6542 42SS Fixed Channel
XC 6548 48" SS Fixed Channel
XC 6560 60" SS Fixed Channel
HS 2 2" Hair Strainer
TNAS SS Threaded Nipple
FXDG 65 Series
DA 6532 32″ SS Grate
DA 6536 36″ SS Grate
DA 6542 42″ SS Grate
DA 6548 48″ SS Grate
DA 6560 60″ SS Grate
XC 6532 32″ SS Fixed Channel
XC 6536 36″ SS Fixed Channel
XC 6542 42″ SS Fixed Channel
XC 6548 48" SS Fixed Channel
XC 6560 60" SS Fixed Channel
HS 2 2" Hair Strainer
TNAS SS Threaded Nipple
FXAS 125 Series
SA 12532 32″ SS Grate
SA 12536 36″ SS Grate
SA 12542 42″ SS Grate
SA 12548 48″ SS Grate
SA 12560 60″ SS Grate
XC 12532 32″ SS Fixed Channel
XC 12536 36″ SS Fixed Channel
XC 12542 42SS Fixed Channel
XC 12548 48" SS Fixed Channel
XC 12560 60" SS Fixed Channel
HS 4 4" Hair Strainer
TN4A SS Threaded Nipple
CDI 43 Cast Iron Drain Body
FXAS 65 Series
SA 6532 32″ SS Grate
SA 6536 36″ SS Grate
SA 6542 42″ SS Grate
SA 6548 48″ SS Grate
SA 6560 60″ SS Grate
XC 6532 32″ SS Fixed Channel
XC 6536 36″ SS Fixed Channel
XC 6542 42″ SS Fixed Channel
XC 6548 48" SS Fixed Channel
XC 6560 60" SS Fixed Channel
HS 2 2” Hair Strainer
TNAS SS Threaded Nipple
FXTIF 65 Series/TD 50
TA 6520 20" SS Grate
TA 6540 40SS Grate
TA 6548 48" SS Grate
TA 6560 60SS Grate
IC 6520 20″ SS Fixed Channel
IC 6540 40SS Fixed Channel
IC 6548 48SS Fixed Channel
IC 6560 60SS Fixed Channel
HS 2 2" Hair Strainer
TNAS SS Threaded Nipple
TKEY Lift Out Key
*Not provided by Innity Drain kits
KEY
(A) Top Grate –
EA65/DA65/SA65/MA65/
TA65/SA125
(B) Bottom Channel –
XC65/IC65/XC125
(C) Threaded Nipple -
TNAS/TN4A
Waterproong Membrane
(D) 2” Throat Clamp Down
Drain Body* (Two Pieces)
4” Throat Clamp Down
Drain Body for FXAS 125
(D1)
(D2)
SS = Stainless Steel
3
FXED65/FXDG65/FXMN65/FXAS65/FXTIF65
kits: DO NOT include the mechanically fas-
tening clamp down drain due to the variance
of material by local code. This is a residential
drain that is available through Innity Drain or
your local plumbing supply from various man-
ufacturers (i.e. Oatey®, Sioux Chief™, JSC™,
PROFLO™, Matco-Norca™).
TD50 kits are provided with a choice of a Cast
Iron, ABS or PVC mechanically fastening clamp
down drain body. (CDI 22/CDP 22/CDA 22).
FXAS125 kits are provided with a (CDI43) Cast
Iron mechanically fastening clamp down drain
body. This item can be substituted for an ABS
or PVC drain body (CDA 42/CDP 42/CDA 43/
CDP 43).
FXED65/FXDG65/FXMN65/FXAS65/FXTIF65
Equipos: NO INCLUYE la sujeción mecánica
del drenaje por la razón que vaa el material
de código local. Este drenaje es residencial
que está disponible a través de Innity Drain
o su local suministro de plomería de diversos
fabricantes. (i.e. Oatey®, Sioux Chief™, JSC™,
PROFLO™, Matco-Norca™).
TD50 equipos son proveído con una elección
de drenaje en hierro fundido, ABS en plástico,
o PVC. (CDI 22/CDP22/CDA 22).
FXAS125 equipos are provided with a (CDI43) Cast
Iron mechanically fastening clamp down drain
body. This item can be substituted for an ABS or
PVC drain body (CDA 42/CDP 42/CDA 43/CDP 43).
2” clamp down drain
not included in kit
Optional Components: (Not Included)
UCP 2 Universal 2” Clamping Plate
UCP 4 Universal 4” Clamping Plate
TNRN Stainless Steel Threaded Nipple (Extends drain height 4)
ERB Eccentric Reducer Bushing 4x2
Available Clamp Down Drains: For FXAS 125 ONLY:
CDI 22 Clamp Down Drain Cast Iron CDA 42 Clamp Down Drain, ABS, 4Throat, 2No Hub Outlet
CDP 22 Clamp Down Drain PVC CDP 42 Clamp Down Drain, PVC, 4” Throat, 2” No Hub Outlet
CDA 22 Clamp Down Drain ABS CDI 42 Clamp Down Drain, Cast Iron, 4Throat, 2No Hub Outlet
CDA 43 Clamp Down Drain, ABS, 4” Throat, 3” No Hub Outlet
CDP 43 Clamp Down Drain, PVC, 4” Throat, 3” No Hub Outlet
Note: Installer must verify all rough-in
dimensions prior to installation and consult
local and national codes. Conformity and
compliance to local and national codes are
the responsibility of the installer.
Tenga en cuenta: Instalador debe compro-
bar todas las dimensiones en las partes pre-
via a la instalación y consultar localmente y
nacionalmente los códigos. La conformidad
y el cumplimiento de códigos local y nacion-
al es responsabilidad del instalador.
Section A-A
FXED 65, FXDG 65,
FXMN 65, FXAS 65
Section A-A
FXAS 125
Section A-A
FXTIF 65/TD 50
2⅞"
1³⁄
¹⁶
"
1"
2½"
6½"
2"
1⅝"
2⅞"
2"
1¹¹
¹⁶
"
2½"
6½"
2"
¾"
1⁷⁄
¹⁶
"
1"
4¹⁄
¹⁶
"
8"
3"
5⅛"
4
(C) Threaded Nipple - TNAS
(D) 2” Throat Clamp Down
Drain Body* (Two Pieces)
Waterproong
Membrane
Mortar Bed
Suboor
(D1)
(D2)
*Not provided by Innity Drain kits
OPTIONAL PROCEDURE:
When drain install is required to be ush
against the nished wall, build out wall with
backer board over round clamp down drain
body (D) to compensate for the drain radius.
PROCEDIMIENTO OPCIONAL:
Cuando el drenaje sea instalado, se requi-
ere que esté completamente a la pared,
construir la pared con múltiples de placas
de cemento sobre el redondo drenaje (D)
para compensar el radial del drenaje.
OPTIONAL
PROCEDURE
Waterproong
Membrane
Double Layer Backer Board
(D) 2” Throat Clamp Down
Drain Body* (Two Pieces)
(D1)
(D2)
*Not provided by Innity Drain kits
Installation
1. Determine the location of the drain outlet
location. Typically linear drains span a dimen-
sion from wall to wall, against a wall or at a
shower entrance.
Instalación
1. Determine la ubicación del emplazamiento
del drenaje. Típicamente el drenaje lineal
atraviesa una dimensión de pared a pared,
contra la pared, o en una entrada de un bo.
2. If clamp down drain body (D) is not
installed. Attach drain body (D2) to existing
waste line and allow drain to recess into
suboor. Ensure that drain body (D2) is level.
Unscrew and remove top clamp down plate
(D1) from drain body .
3. Spread a primary mortar bed across the
intended shower area. Pitch this bed in four
directions towards the drain body (D2).
4. When mortar layer is dry, perform necessary
waterproong (PVC Liner, Rubber Liner, Lead
Pan, Copper Pan, Hot Mop, Fiberglass) as per
local code. Ensure waterproong layer reaches
the edge of the hole in the drain body (D2).
2. Si el drenaje (D) no está instalado. Adjuntar el
drenaje (D2) a la nea de residuos existentes y
permite el drenaje a que recese en el piso. Ase-
gura, que el drenaje (D2) este nivelado. Destor-
nilla y remueve la placa de sujeción de arriba.
3. Esparcir una primaria de capa de mortero a
través del destino o zona del bo. Lanzar la
capa de mortero en cuatro direcciones hacia
el drenaje (D2).
4. Cuando la capa de mortero este seca, realice
la impermeabilización necesaria (Forro del PVC,
cobre, panal de vidrio) según el código local.
Asegura que la capa de impermeabilización
alcance al borde del agujero en el drenaje (D2).
5
Channel Outlet
(C) Threaded Nipple
TNAS/TN4A
(B) Bottom Channel –
XC65/IC65/XC125
100% Silicone Bead
5. Reattach the top clamp down plate (D1)
to the clamp down drain body (D2) over
the waterproong layer using bolts. Screw
threaded nipple (C) into top clamp down plate
(D1). Adjust to the desired height. Turn clock-
wise to lower, counter-clockwise to raise.
5. Vuelva a colocar la placa de sujeción de arriba
del drenaje (D2) sobre las capas de imperme-
abilizacn utilizando tornillo. Enrosca el niple
roscado(C) adentro de la placa del drenaje (D1).
Adaptarla a la altura que desea. Gire hacia la
derecha para bajar, hacia la izquierda para subir.
6. Clean lip of the outlet hole using dena-
tured alcohol. Apply a bead of silicone caulk
around the outside of the outlet of the stain-
less steel channel (B). Press channel outlet
into the threaded nipple (C) to create a water
tight seal. Be sure to support the length of
the channel after setting.
7. Create a mortar bed the length of the
channel on the waterproong membrane and
backll the underside of the stainless steel
channel and level. Use necessary amount of
mortar to adequately support the channel.
6. Limpie el reborde de la salida del agujero en la
parte baja del canal de PVC usando alcohol des-
naturalizado. Aplicar un cordón de sellador de
silicona alrededor del exterior del canal de acero
inoxidable (B). Presione el agujero del canal
hacia el interior del niple roscado(C) para crear
un sello hertico. Asegure que la longitud este
compatible al canal desps de establecer.
7. Crear un base de mortero de la longitud del
canal en la membrana de impermeabilización y
rellene la parte de inferior del canal de acero inox-
idable y nilelo. Utilice la cantidad necesaria de
mortero para soportar adecuadamente el canal.
Waterproong Membrane Backer Board
Motar Bed
Shims
Suboor
(B) Bottom Channel
6
Suboor
Stainless Steel
Channel Assembly
Final Mortar Bed
Clamp Down
Floor Drain
Pre-Pitched
Mortar Bed
Waterproong
Membrane
Finishing Material
Backer Board
Thinset
Finished Grate
8. Using desired oor material, mark the
thickness of the material along the channel so
that it will nish 1/16” above the channel. Lay
nal mortar bed across the wet area. Pitch
this bed in one plane toward the linear drain.
Ensure space for thinset and nishing mate-
rial to nish 1/16” above the channel. After
dry, apply a bead of silicone caulk around the
channel. Lay thinset and nishing material,
and have material nish to the edge of the
combined stainless steel channel. DO NOT
allow nishing material to nish on top of the
stainless steel channel edge.
9. FXTIF 65/TD 50 INSTALL: Spread a layer
of mortar into the Tile Insert Frame (TA65),
allowing for thinset and nishing material to
nish 1/16” above the metal frame. Allow to
dry, spread thinset and lay material.
8. Utilizando el material de piso deseado, marque
el espesor del material a lo largo del canal para
que termine 1/16arriba del canal. Sentar la últi-
ma capa de mortero a tras de la zona mojada.
Lanzar esta capa en un plano hacia el drenaje
lineal. Asegura que el espacio para el thinset
y el material terminen 1/16” arriba del canal.
Una vez este seco, aplique un cordón de silicona
alrededor del canal. Colocar el thinset y material
terminado, y tener el material terminado al borde
del canal de acero inoxidable. NO DEJE o PERMI-
TA que el material terminado termine en la parte
superior del canal de acero inoxidable.
9. FXTIF 65/TD 50 INSTALACION: Extender
una capa de mortero en la inserción en la
parte (TA65), permitiendo el thinset y el mate-
rial terminado a 1/16” arriba de la estructura
de metal. Permitir que se seque, difundir el
thinset y tender el material.
Caulking
Mortar Bed
Mortar Bed
Sub-oor
Waterproong
Membrane
Finishing Material
Assure that grate is lower
than installed tile
Mortar
Bed
Mortar Bed
Sub-oor
Waterproong
Membrane
Before nishing
material
Antes que el material
esté terminado
After nishing
material
Desps que el material
esté terminado
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Infinity Drain FXAS 6560 BK Guía de instalación

Tipo
Guía de instalación