Chief RSAUS Guía de instalación

Marca: Chief

Modelo: RSAUS

Categoría: Pared

Tipo: Guía de instalación

Este manual también es adecuado para

RSAU
RSAUW

INSTALLATION INSTRUCTIONS

Instructions d´installation

Istruzioni di installazione

Installationsanleitung

Instrucciones de instalación

Installatie-instructies

Instruções de Instalação

RSA Projector Mounts

RPA Elite Series Projector Mount

RSA

RSA Projector Mounts Installation Instructions

DISCLAIMER

Milestone AV Technologies, and its affiliated corporations and

subsidiaries (collectively, "Milestone"), intend to make this

manual accurate and complete. However, Milestone makes no

claim that the information contained herein covers all details,

conditions or variations, nor does it provide for every possible

contingency in connection with the installation or use of this

product. The information contained in this document is subject

to change without notice or obligation of any kind. Milestone

makes no representation of warranty, expressed or implied,

regarding the information contained herein. Milestone assumes

no responsibility for accuracy, completeness or sufficiency of

the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,

damage to equipment, or voiding of factory warranty! It is the

installer’s responsibility to make sure all components are

properly assembled and installed using the instructions

provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or

damage to equipment! It is the installer’s responsibility to

make sure the structure to which this component is attached

can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the

component.

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the

installer’s responsibility to make sure the combined weight of

all components attached to the RSA does not exceed 25 lbs

(11.34 kg).

AVISOS y PRECAUCIONES

IMPORTANTES!

AVISO: Un AVISO llama su atención sobre la posibilidad de

sufrir lesiones de gravedad o incluso mortales si no sigue las

instrucciones.

PRECAUCIÓN: Una not de PRECAUCIÓN llama su atención

sobre la posibilidad de dañar o destruir el equipo si no sigue

las instrucciones.

AVISO: Si no lee, comprende perfectamente y sigue todas

las instrucciones, podría causar daños graves daños

personales y materiales o anular la garantía de fábrica. El

instalador es el responsable de asegurarse de que todos los

componentes están correctamente montados e instalados

siguiendo las instrucciones indicadas.

AVISO: Si no se proporciona la resistencia estructural

adecuada para este componente, podrían provocarse graves

daños personales o materiales. El instalador es el

responsable de asegurarse de que la estructura a la que este

componente está sujeta puede soportar cinco veces el peso

combinado de todo el equipo. Refuerce la estructura según

sea necesario antes de instalar el componente.

AVISO: Si se excede el peso máximo, podrían causarse

graves daños personales o materiales. El instalador es

responsable de asegurarse de que el peso combinado de

todos los componentes montados en el RSA no excede

11.34 kg.

WICHTIGE WARN- und

VORSICHTSHINWEISE!

WARNUNG: Ein WARNHINWEIS macht auf mögliche

schwere oder tödliche Verletzungen aufmerksam, die bei

Nichtbefolgung der Anweisungen eintreten können.

VORSICHT: Ein VORSICHTSHINWEIS macht auf Schäden

oder mögliche Zerstörung des Geräts aufmerksam, die bei

Nichtbefolgung der Anweisungen eintreten können.

WARNUNG: Falls nicht alle Anweisungen gelesen und gut

verstanden werden, kann dies zu schweren

Körperverletzungen, Schaden an den Geräten führen und die

Werksgarantie nichtig machen! Der Monteur ist dafür

verantwortlich, dass alle Komponenten unter Einhaltung der

mitgelieferten Anweisungen korrekt zusammengebaut und

eingebaut werden.

WARNUNG: Wenn für diese Komponente keine

ausreichende bauliche Tragkraft vorhanden ist, kann dies zu

schweren Körperverletzungen oder Schäden an den Geräten

führen! Der Installateur ist dafür verantwortlich zu überprüfen,

ob die Wand, an der diese Komponente verankert wird, das

Fünffache der Gesamtlast aller befestigten Geräte sicher

tragen kann. Andernfalls muss die Wand verstärkt werden,

bevor die Komponente angebracht wird.

Installation Instructions RSA Projector Mounts

WARNUNG: Wenn das zulässige Gewicht überschritten wird,

kann dies zu schweren Körperverletzungen oder Schäden an

den Geräten führen! Der Monteur ist dafür verantwortlich,

dass das kombinierte Gewicht aller Komponenten, die am

Modell RSA befestigt sind, nicht mehr als 11.34 kg beträgt.

ADVERTÊNCIAS e AVISOS

IMPORTANTES!

ADVERTÊNCIA: Os alertas de ADVERTÊNCIA avisam-no

para a possibilidade de ocorrência de graves lesões ou morte

no caso de incumprimento das instruções.

AVISO: Os alertas de AVISO avisam-no para a possibilidade

de danos ou destruição do equipamento no caso de

incumprimento das instruções.

ADVERTÊNCIA: Se não ler, compreender completamente e

seguir todas as instruções podem ocorrer graves lesões

pessoais, danos no equipamento e a garantia de fábrica

pode ser anulada! É da responsabilidade do instalador

certificar-se de que todos os componentes são

correctamente montados e instalados de acordo com as

instruções fornecidas.

ADVERTÊNCIA: Se não for proporcionado apoio estrutural

adequado a este componente podem ocorrer graves lesões

pessoais ou danos no equipamento! É da responsabilidade

do instalador certificar-se de que a estrutura à qual este

componente é ligado pode suportar cinco vezes o peso

combinado de todo o equipamento. Reforce a estrutura

conforme necessário antes de instalar o componente.

ADVERTÊNCIA: Exceder a capacidade de peso pode

resultar em graves lesões pessoais ou danos no

equipamento! É da responsabilidade do instalador certificar-

se de que o peso combinado de todos os componentes

ligados ao RSA não excede 11.34 kg.

AVVERTENZE e PRECAUZIONI

IMPORTANTI!

AVVERTENZA: Un'AVVERTENZA mette in guardia in merito

alla possibilità di gravi infortuni, anche letali, qualora non si

osservino le istruzioni.

ATTENZIONE: Un'ATTENZIONE indica la possibilità di gravi

danni all'attrezzatura qualora non ci si attiene alle istruzioni al

riguardo.

AVVERTENZA: La mancata comprensione e ottemperanza

alle istruzioni fornite può provocare gravi lesioni personali,

danni all'apparecchiatura o annullare la garanzia fornita dal

produttore. Spetta all'installatore verificare che tutti i

componenti siano assemblati correttamente e installati

secondo le istruzioni fornite.

AVVERTENZA: Una resistenza strutturale inadeguata per

questo componente può arrecare gravi infortuni o

danneggiare l'apparecchiatura. È responsabilità

dell'installatore verificare che la struttura alla quale è fissato il

componente sostenga con sicurezza cinque volte il carico

combinato di tutta l'apparecchiatura. Rinforzare la struttura

secondo necessità prima di installare i componenti.

AVVERTENZA: Un peso superiore alla capacità nominale

può arrecare gravi infortuni o danneggiare l'apparecchiatura.

È responsabilità dell'installatore verificare che il peso totale di

tutti i componenti montati sul RSA non superi 11.34 kg (25

lb).

BELANGRIJKE AANWIJZINGEN en

WAARSCHUWINGEN!

WAARSCHUWING: Een WAARSCHUWING vestigt uw

aandacht op de mogelijkheid van ernstig of dodelijk letsel als

u de instructies niet opvolgt.

VOORZICHTIG: De aanwijzing VOORZICHTIG vestigt uw

aandacht op de mogelijkheid van beschadiging of

onherstelbare beschadiging van de apparatuur als u de

betreffende instructies niet opvolgt.

WAARSCHUWING: Door niet alle instructies te lezen,

volledig te begrijpen en op te volgen, riskeert u ernstig

persoonlijk letsel, beschadiging van de apparatuur en het

vervallen van de fabrieksgarantie. Degene die het product

installeert is ervoor verantwoordelijk dat alle onderdelen aan

de hand van de meegeleverde handleiding op de juiste wijze

worden samengebouwd en gemonteerd.

WAARSCHUWING: Als u voor deze component

onvoldoende constructiesterkte beschikbaar stelt, riskeert u

ernstig persoonlijk letsel of beschadiging van de apparatuur!

Degene die de structuur monteert waaraan deze component

is bevestigd, is ervoor verantwoordelijk dat deze minimaal vijf

maal het gezamenlijke gewicht van alle apparatuur kan

dragen. Zonodig dient u de structuur vóór de montage van

de component te versterken.

RSA Projector Mounts Installation Instructions

WAARSCHUWING: Overschrijding van het draagvermogen

kan de oorzaak zijn van ernstig persoonlijk letsel en

beschadiging van de apparatuur! Degene die het product

installeert is ervoor verantwoordelijk dat het totale gewicht

van alle componenten die aan de RSA worden bevestigd een

gewicht van 11.34 kg niet overschrijdt.

IMPORTANTS AVERTISSEMENTS et

PRÉCAUTIONS!

ADVERTISSEMENT: Un ADVERTISSEMENT vous met en

garde contre les possibilités de blessures graves ou de

danger de mort si vous ne suivez pas les instructions.

PRÉCAUTION: Une PRÉCAUTION vous met en garde

contre les possibilités d´endommagements et de destruction

de l´équipement si vous ne suivez pas les instructions

correspondantes.

ADVERTISSEMENT: Le manque de la lecture, de la

compréhension et du respect total de toutes les instructions,

peut entraîner des blessures corporelles graves,

endommager l'équipement ou annuler la garantie d'usine. Il

incombe à l'installateur de s'assurer que tous les composants

sont correctement assemblés et installés à l'aide des

instructions fournies.

ADVERTISSEMENT: L'absence de l'apport d'une résistance

structurelle appropriée pour ce composant peut entraîner des

blessures corporelles graves ou endommager l'équipement.

Il incombe à l'installateur de s'assurer que la structure à

laquelle le composant est attaché peut soutenir cinq fois le

poids combiné de tout l'équipement. Renforcer la structure

selon les besoins avant l'installation du composant.

ADVERTISSEMENT: Dépasser la capacité pondérale peut

entraîner des blessures corporelles graves ou endommager

l'équipement. Il incombe à l'installateur de s'assurer que le

poids combiné de tous les composants attachés à RSA n'est

pas supérieur à 11.34 kg (25 lb).

DIMENSIONS

4.39

111.6

4°

ROLL ADJUSTMENT

4.38

111.1

2.88

BOLT CIRCLE

.22

5.6

THREADS ONTO 1-1/2' NPT

1.44

36.5

25°

PITCH ADJUSTMENT

3.10

78.8

Installation Instructions RSA Projector Mounts

LEGEND

Tighten Fastener

Serrez les fixations

Serrare il fissaggio

Befestigungsteil festziehen

Apretar elemento de fijación

Bevestiging vastdraaien

Apertar fixador

Loosen Fastener

Desserrez les fixations

Allentare il fissaggio

Befestigungsteil lösen

Aflojar elemento de fijación

Bevestiging losdraaien

Desapertar fixador

Phillips Screwdriver

Tournevis à pointe cruciforme

Cacciavite a stella

Kreuzschlitzschraubendreher

Destornillador Phillips

Kruiskopschroevendraaier

Chave de fendas Phillips

Hex-Head Wrench

Clé à tête hexagonale

Chiave esagonale

Sechskantschlüssel

Llave de cabeza hexagonal

Zeskantsleutel

Chave de cabeça sextavada

Open-Ended Wrench

Clé à fourche

Chiave a punte aperte

Gabelschlüssel

Llave de boca

Steeksleutel

Chave de bocas

By Hand

À la main

A mano

Von Hand

A mano

Met de hand

Com a mão

Pencil Mark

Marquage au crayon

Segno a matita

Stiftmarkierung

Marcar con lápiz

Potloodmerkteken

Marcar com lápis

Drill Hole

Percez un trou

Praticare un foro

Bohrloch

Perforar

Gat boren

Fazer furo

Adjust

Ajuster

Regolare

Einstellen

Ajustar

Afstellen

Ajustar

Remove

Retirez

Rimuovere

Entfernen

Quitar

Verwijderen

Remover

Optional

En option

Opzionale

Optional

Opcional

Optie

Opcional

Security Wrench

Clé de sécurité

Chiave di sicurezza

Sicherheitsschlüssel

Llave de seguridad

Veiligheidssleutel

Chave de segurança

RSA Projector Mounts Installation Instructions

Hammer

Martillo

Hammer

Martelo

Martello

Hamer

Marteau

Target of Projector

Punto de enfoque del proyector

Ziel des Projektors

Mira do projector

Punto di proiezione

Doel van de projector

Cible du projecteur

Installation Instructions RSA Projector Mounts

#2 7/16" 7/32" (6mm) dia.

5/32"

A (1)

[RSA Projector Mount]

RSA Projector Mounts Installation Instructions

Ø 2.5mm

(Ø 3/32”)

45mm

(1-3/4”)

(A)

RSA INSTALLATION

Threaded Pipe Installation

1. Carefully determine required mounting location.

IMPORTANT ! : This will require knowing the lens

to screen distance. See projector specifications

for details on determining this distance.

2. Install ceiling plate and extension accessories

following installation instruction provided by

manufacturer.

WARNING:

IMPROPER INSTALLATION CAN

RESULT IN SERIOUS PERSONAL INJURY OR

DAMAGE TO EQUIPMENT! Structural members

MUST be capable of supporting five times the

combined weight of all equipment being mounted.

3. Align RSA with end of NTP pipe.

4. Thread RSA up onto pipe by turning counter-

clockwise until hand tight.

Rough Alignment of RSA

1. Turn RSA clockwise or counter-clockwise until front

of mount is facing target.

IMPORTANT ! : When RSA is properly

positioned, the set screw access hole should be

pointing directly at target.

(see bottom detail in figure at left)

2. Secure RSA to pipe by turning set screw with a 5/

32" hex key until tight.

CAUTION:

DO NOT OVERTIGHTEN!

Overtightening of setscrew can damage threads on

pipe.

Installation Instructions RSA Projector Mounts

INSTALLATION

1a Wood Stud Installation

1. Carefully determine required mounting location.

IMPORTANT ! : This will require knowing the lens

to screen distance. See projector specifications for

details on determining this distance.

WARNING:

IMPROPER INSTALLATION CAN

RESULT IN SERIOUS PERSONAL INJURY OR

DAMAGE TO EQUIPMENT! Structural members

MUST be capable of supporting five times the

combined weight of all equipment being mounted.

2. Using the RSA as a guide, mark four mounting hole

locations with a pencil or similar tool.

3. Drill four 3/32" (2.5mm) dia. pilot holes to a depth of

1-3/4" (45mm) deep.

4. Align four mounting holes in RSA with four pilot

holes.

IMPORTANT ! : Make sure mount is properly

oriented towards target before securing to

structure.

5. Secure RSA to structure using four #10 flat washers

and four #10 x 3" Phillips head wood screws (not

included).

Ø 2.5mm

(Ø 3/32”)

45mm

(1-3/4”)

(A)

x 4

RSA Projector Mounts Installation Instructions

Ø 6.3mm

(Ø 1/4”)

64mm

(2-1/2”)

Concrete Installation

1. Determine mounting location.

WARNING:

IMPROPER INSTALLATION CAN

RESULT IN SERIOUS PERSONAL INJURY OR

DAMAGE TO EQUIPMENT! Structural members

MUST be capable of supporting five times the

combined weight of all equipment being mounted.

2. Using the RSA as a guide, mark four mounting hole

locations on ceiling using a pencil or similar tool.

3. Drill four 1/4" (6.3mm) diameter pilot holes to a

depth of 2-1/2" (64mm) deep.

4. Align four mounting holes in RSA with four pilot

holes.

IMPORTANT ! : Make sure mount is properly

oriented towards target before securing to

structure.

5. Install four Toggler A6 Alligator concrete anchors

(not included) by inserting into pilot holes and

pounding in until flush with mounting surface.

6. Secure RSA to structure using four #10 flat washers

and four #10 x 3" Phillips head wood screws. (not

included)

(A)

X (4)

Installation Instructions RSA Projector Mounts

PROJECTOR INSTALLATION

IMPORTANT ! : Model RSA uses Chief "SSB"

Series interface brackets.

Install Interface Bracket

1. Partially thread thumb nuts onto Phillips screws until

screw end is visible in top of thumb screw.

IMPORTANT ! : DO NOT fully tighten thumb

screws at this time.

Threaded Rod Installation

The RSA can be secured to unistrut, angle or channel

assembly overhead structural members (trusses or I-

beams) using four #10-24 diameter threaded rods.

WARNING:

IMPROPER INSTALLATION CAN

RESULT IN SERIOUS PERSONAL INJURY OR

DAMAGE TO EQUIPMENT! Structural members

MUST be capable of supporting five times the

combined weight of all equipment being mounted.

1. Carefully determine required mount position.

IMPORTANT ! : This will require knowing the lens

to screen distance. See projector specifications

for determining this distance.

NOTE:

Threaded rod and installation hardware not

included.

2. Secure one end of the threaded rod to the structural

member.

3. Install four #10-24 jam nuts on each threaded rod.

4. Install the RSA on the threaded rod.

NOTE:

Hole in the RSA allows socket wrench access

without unit disassembly.

5. Secure the RSA to the threaded rod using four

#10-24 nuts.

Example Only

(Interface bracket

varies dependent

on projector model)

(A)

X 4

RSA Projector Mounts Installation Instructions

Install Projector With Interface Bracket

1. Orient projector with interface bracket as shown in

figure 2b at left.

2. Lift projector so that screws with thumb nuts are

aligned with mounting slots in mount base.

3. Slide projector with mounting bracket onto mounting

slots in mount base until screws are seated against

the back of mounting slots. See figure 2b and 2c.

WARNING:

IMPROPER INSTALLATION CAN

LEAD TO PROJECTOR FALLING RESULTING IN

SERIOUS PERSONAL INJURY OR DAMAGE TO

EQUIPMENT. Make certain mounting slots in mount

base slide under thumb screws and that screws are

seated in the back of slots.

WARNING:

IMPROPER INSTALLATION CAN

LEAD TO PROJECTOR FALLING RESULTING IN

SERIOUS PERSONAL INJURY OR DAMAGE TO

EQUIPMENT. DO NOT substitute hardware. Use only

the hardware provided by the manufacturer.

1. Secure interface bracket to mount using installation

instructions and hardware provided with interface

bracket.

NOTE:

Interface brackets can be installed using the

optional All-Points Security Kit included with

the SSB or SSM mounting solutions.

(A)

Example Only

(Interface bracket

varies dependent

on projector model)

Example Only

(Interface bracket

varies dependent

on projector model)

Installation Instructions RSA Projector Mounts

Securing Projector with Interface Bracket

to Model RSA Mount.

WARNING:

IMPROPER INSTALLATION CAN

LEAD TO PROJECTOR FALLING RESULTING IN

SERIOUS PERSONAL INJURY OR DAMAGE TO

EQUIPMENT. Make certain mounting slots in mount

base slide under thumb screws and that screws are

seated in the back of slots.

1. Turn thumb nuts until tight to secure projector to

mount.

X 4

Example Only

(Interface bracket

varies dependent

on projector model)

RSA Projector Mounts Installation Instructions

Pitch Adjustment

1. Loosen pitch adjustment locking screw on each end

of the RSA projector mount using a #2 Phillips

screwdriver.

2. Adjust projector angle to desired pitch.

3. Tighten pitch adjustment locking screw on each end

of the RSA projector mount using a #2 Phillips

screwdriver.

ADJUSTMENTS

YAW Adjustment

1. Loosen yaw adjustment screw using a 5/32" hex

key.

NOTE:

Yaw is only adjustable when attached to a

threaded pipe.

WARNING:

Do not turn the projector to the end of

the pipe threads. The projector, interface plate and

projector will fall from the pipe if it is unthreaded too

far!

2. Adjust projector by turning the projector on the pipe

to the desired yaw position.

3. Tighten yaw adjustment locking screw using a 5/32"

hex key.

3Example Only

(Interface bracket

varies dependent

on projector model)

Example Only

(Interface bracket

varies dependent

on projector model)

Installation Instructions RSA Projector Mounts

Roll Adjustment

1. Loosen roll adjustment locking screw on each side

of the RSA projector mount using a #2 Phillips

screwdriver.

2. Adjust projector to desired roll position.

3. Tighten roll adjustment locking screw on each side

of the RSA projector mount using a #2 Phillips

screwdriver.

Example Only

(Interface bracket

varies dependent

on projector model)

RSA Projector Mounts Installation Instructions

Chief Manufacturing, a products division

of Milestone AV Technologies

8800-002005 Rev00

Duchossois Group Company

www.chiefmfg.com

04/09

USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378

P800.582.6480 / 952.894.6280

F877.894.6918 / 952.894.6918

Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands

P+31 (0)40 2668620

F+31 (0)40 2668615

Asia Pacific A Room 24F, Block D, Lily YinDu International Building

LuoGang, BuJi Town, Shenzhen, CHINA.

P+86-755-8996 9226

F+86-755-8996 9217

Chief RSAUS Guía de instalación

Marca: Chief

Modelo: RSAUS

Categoría: Pared

Tipo: Guía de instalación

Este manual también es adecuado para

RSAU
RSAUW

Descargar PDF

informe

En otros idiomas

français: Chief RSAUS Guide d'installation
italiano: Chief RSAUS Guida d'installazione
English: Chief RSAUS Installation guide
Deutsch: Chief RSAUS Installationsanleitung

Chief RSAUS Guía de instalación

Este manual también es adecuado para

Chief RSAUS Guía de instalación

En otros idiomas

Documentos relacionados

Otros documentos