Panasonic DVD VCR Combo PV-D4732S Manual de usuario
- Categoría
- Reproductores de DVD
- Tipo
- Manual de usuario
Connections and Initial Setup Procedures are on pages 12 to 17.
DVD/VCR DECK
Operating Instructions
Please read these instructions carefully before attempting to connect, operate or
adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
LSQT0618B
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Initial Setup
(Connection)
Basic
Operation
VCR
Operation
For Your
Information
DVD
Operation
Model No. PV-D4732
/
PV-D4732S
®
As an ENERGY STAR Partner, Matsushita Electric Corporation of
America has determined that this product or product model meets the
ENERGY STAR guidelines for energy efficiency.
®
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:121
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from a power source indicated on the
unit or in this manual. If necessary, have your
Electric Utility Service Company or Video Products
Dealer verify the power source in your home.
2 POLARIZED OR GROUNDING PLUG
As a safety feature, this product comes with either
a polarized power cord plug (one blade is wider
than the other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot
fully insert the plug, try reversing it. If it still will not fit,
have an electrician install the proper wall outlet. Do not
defeat the safety feature by tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding
outlet. If necessary, have an electrician install the
proper outlet. Do not defeat the safety feature by
tampering with the plug.
3 POWER CORD
Make sure power cords are routed so that they
are not likely to have anything rest on them, roll
over them, or be in the way of walking traffic.
If an extension cord is used, make sure it also
has either a polarized or grounded plug and that
the cords can be securely connected.
Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified service technician.
Overloaded outlets and extension cords are fire
hazards and should be avoided.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If they are blocked,
heat build-up inside the unit can cause failures that
may result in a fire hazard or heat damage to
cassettes or discs.
For protection, follow these rules:
a. Never cover ventilation slots or the unit while in
use, or operate the unit when placed on a bed,
sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless proper ventilation is provided.
5 PLACEMENT: AVOID EXTREMELY HOT LOCATIONS
OR SUDDEN TEMPERATURE CHANGES
Do not place the unit over or near heater or
radiator, in direct sunlight, inside closed vehicles,
in high temperature [over 104°F (40°C)], or in over
75% humidity. If the unit is suddenly moved from
a cold place to a warm one, moisture may
condense in the unit and on the tape causing
damage. Never subject the unit to vibration,
impact, or place it so that the surface is titled as
internal parts may be seriously damaged.
6 TO AVOID PERSONAL INJURY
• Do not place unsecured equipment on a sloping
surface.
• Do not place this unit on any support that is not
firm, level, and adequately strong.
The unit could fall causing serious
injury to a child or adult and
damage to the unit.
• An appliance and cart
combination should be moved
with care. Quick stops,
excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.
• Carefully follow all operating instructions and
use the manufacturer's recommended
accessories when operating this unit or
connecting it to any other equipment.
FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY
AND OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON THE UNIT
USING THE UNIT
If the unit has been in storage or moved to a new location,
refer first to the INSTALLATION section of these safeguards.
1
KEEP THE UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN, MOISTURE, OR
STRONG IMPACT, unplug the unit and have it inspected by a
qualified service technician before use.
3 DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time,
disconnect all equipment from the power source as well as
the antenna and cable system.
4 WHEN THE UNIT IS PLUGGED IN
• Never expose the unit to rain or water. DO NOT OPERATE
if liquid has been spilled into the unit. Immediately unplug
the unit, and have it inspected by a service technician.
Fire and shock hazards can result from electrical shorts
caused by liquid contact inside.
• Never drop or push any object through openings in the unit.
Some internal parts carry hazardous voltages and contact
can cause electric shock or fire hazard.
Do not put any foreign object on the disc tray.
• Avoid placing the unit directly above or below your TV set
as this may cause electrical interference. Keep all magnets
away from electronic equipment.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically untreated
cloth to gently remove dust or debris. DO NOT USE cleaning
fluids, aerosols, or forced air that could over-spray, or seep
into the unit and cause electrical shock. Any substance such
as wax, adhesive tape, etc. may mar the cabinet surface.
Exposure to greasy, humid, or dusty areas may adversely
affect internal parts.
SERVICE
1 DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating
instructions, this product does not operate properly, do not
attempt to open or remove covers, or make any
adjustments not described in the manual. Unplug the unit
and contact a qualified service technician.
2 IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified
by the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other hazards.
3
HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as
described in the manufacture’s service literature to ensure
that the unit is in safe operating condition.
Important Safeguards and Precautions
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC
- NATIONAL
ELECTRICAL CODE
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded
so as to provide some protection against built up static
charges and voltage surges.
Section 810 of the National Electrical
Code, ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
with respect to proper grounding
of the mast and supporting
structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes and requirements for the grounding electrode.
2
KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS
An outside antenna system should be located well away from
power lines, electric light or power circuits and where it will never
come into contact with these power sources if it should happen
to fall. When installing an outside antenna, extreme care should
be taken to avoid touching power lines, circuits or other power
sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.
2
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:122
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage
within the unit may have sufficient magnitude to cause
electric shock.
Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that important literature
concerning the operation and maintenance of this unit
has been included. Therefore, it should be read
carefully in order to avoid any problems.
FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s
authority to operate.
Safety Precautions/Mesures de sécurité
WARNING: To prevent fire or shock hazard, do not expose this
equipment to rain or moisture.
CAUTION: To prevent electric shock, match wide blade of plug to
wide slot, fully insert.
Avertissement: Afin de prévenir tout risque d’incendie ou de chocs
électriques, ne pas exposer cet appareil à la pluie ou
à une humidité excessive.
Attention: Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de la
prise et pousser jusqu’au fond.
Region Management Information:
This DECK is designed and manufactured to respond to the
Region Management Information that is recorded on a DVD
disc. If the Region number described on the DVD disc does
not correspond to the Region number of this DECK, this
DECK cannot play this disc.
The Region number
for this DECK is 1.
1
CAUTION:
UNIT IS A CLASS I LASER PRODUCT.
HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD
CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED.
BE SURE TO OPERATE THE UNIT CORRECTLY INSTRUCTED.
WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE
YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER
OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE UNIT
YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
CAUTION:
LASER RADIATION
WHEN OPEN DO NOT
STARE INTO BEAM.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited
viewing uses only.
ATTENTION:
RAYONNEMENT
LASER EN CAS
D’OUVERTURE.
NE PAS REGARDER
DANS LE FAISCEAU.
(Inside of product)
FCC NOTE:
This equipment has been tested and found to comply with part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when operated in a residential
environment. If this equipment does cause interference to radio or television reception, which can be
determined by turning the equipment off and on, use the equipment in another location and/or utilize
an electrical outlet different from that used by the receiver.
If necessary, consult the dealer or an experienced radio/TV technician for help. The user may find the
booklet, “Something About Interference” available from FCC local regional offices helpful.
FCC Caution:
To assure continued compliance, (example- use only shielded interface cables when connecting to
other devices.) Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
3
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:123
4
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Congratulations
on your purchase of one of the most
sophisticated and reliable products on the
market today. Used properly, it will bring you
years of enjoyment. Please fill in the
information below. The serial number is on the
tag located on the back of your DECK.
Before Using
• Date of Purchase
• Dealer Purchased From
• Dealer Address
• Dealer Phone No.
• Model No.
• Serial No.
To order accessories, call toll free
1-800-332-5368.
If disc is brought from a cold to a warm
environment, moisture may form on the disc
Wipe away moisture with a soft, dry, lint-free cloth
before using disc. (See above.)
Improper disc storage
Discs could be damaged if stored or left in areas:
• exposed to direct sunlight.
• that are humid or dusty.
• near heat (i.e. heater, radiator, etc.).
Disc Handling
To clean disc surface
With a soft, damp (water only) cloth, gently wipe
from the center hole to the outer edge as shown
below. (Wiping in a circular pattern will scratch the
surface.)
Handling precautions
• Only hold disc by edges as shown below.
Fingerprints, dirt and scratches can cause
skipping and distortion.
• Do not write on label side of disc.
• Never use record cleaning sprays, benzine,
thinner, static electricity prevention liquids, or any
other solvent.
• Be careful not to drop or bend disc.
• Do not place more than
1 disc on disc tray.
• Do not try to close
disc tray when disc
is not properly placed.
• Always store discs in
their proper cases
when not in use.
Disc formats supported by this DECK
DECK can play back discs bearing any of the
following marks:
Discs which cannot be played
• DVD with Region No. other than “1” or “ALL”
• DVD of PAL system • DVD-R/DVD-RAM
• DVD-ROM • CD-ROM
• CDV • CD-G
DVD
3” (8 cm) disc / 5” (12 cm) disc
Video CD
3” (8 cm) disc / 5” (12 cm) disc
CD
3” (8 cm) disc / 5” (12 cm) disc
is a registered trademark.
Do not try to play Photo CD.
Disc tray
Disc
1) Open cover.
3) Close cover.
Loading the Batteries
2) Insert
batteries as
marked.
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese
batteries.
5
Table of Contents
Timer Recording .............................................................. 24, 25
MTS Broadcast/ VHS Hi-Fi Stereo System .................... 26, 27
Multi-Brand Control Feature ........................................... 28, 29
Tape Operation (Search System) ....................................... 30 ~ 32
Special VCR Features ..................................................... 33, 34
Copying Your Tapes (Dubbing) ......................................................... 35
Disc Operation ............................................................... 36 ~ 40
DVD Operation using On-Screen Displays ................... 41, 42
MP3 Playback Operation....................................................... 43
DVD Lock Feature ................................................................. 44
Settings for DVD Operation .......................................... 45 ~ 47
Language Code List .............................................................. 48
DVD / VCR
Warning and Instruction Displays........................................ 49
Before Requesting Service............................................. 50, 51
Limited Warranty ............................................................. 52, 53
Customer Services Directory ............................................... 53
Spanish (Español) Quick Use Guide............................ 54 ~ 59
Index ....................................................................... Back Cover
DVD / VCR
Important Safeguards and Precautions ............................ 2, 3
Before Using ............................................................................4
DECK & Cassette Information ........................................... 6 , 7
Location of Controls ....................................................... 8 ~ 10
Displays (On Screen Displays and Multi Function Display) .................... 11
Connections .................................................................. 12 ~ 15
Initial Setup for Basic Connections (Ready to Play) .......... 16, 17
VCR
Reset Language, Channels, Clock, VCR’s Output Channel ... 18, 19
Playback/ Record on a Tape........................................... 20, 21
DVD
Basic DVD Operation ...................................................... 22, 23
Initial Setup
(Connection)
Basic
Operation
VCR
Operation
For Your
Information
DVD
Operation
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:125
6
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DECK & Cassette Information
Video Head Clog Sensor
During playback, this
screen appears if
clogging is detected.
To remove screen,
press PLAY on the
remote or DECK.
Playing older or damaged tapes may eventually
cause video heads to become clogged.
V
I
D
EO HEADS
M
AY
N
EED
CLE
A
N
I
NG
PLEASE
I
NSERT
HEAD
CLE
A
N
I
NG
CASSE
TT
E
OR
REFER
T
O
MANUAL
END
:
P
L
AY
• Use “dry” type head cleaning cassette
only. (Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
• If head clog symptoms persist, contact your
nearest Factory Servicenter or authorized
Servicenter (see p. 52).
Head Cleaning
Only use tapes with the mark in this DECK.
Prevent Accidental Tape Erasure
Record/ Playback Time
Record Tab
Cover the hole
with cellophane tape.
To record again
Break off the tab to
prevent recording.
SP
(Standard Play)
2 Hours
40 Minutes
1 Hour 2 Hours
5 Hours
20 Minutes
2 Hours 4 Hours
LP
(Long Play)
3 Hours 6 Hours 8 Hours
SLP
(Super Long Play)
Type of Video Cassette
Tape Speed
Setting
T160T120T60
Use a soft cloth or dusting attachment of a vacuum cleaner to remove dust from the ventilation holes
on the back sides and bottom of the cabinet. Plastic surfaces are easily scratched and can be
marred by alcohol and various solvents. Avoid excessive use of oil-based furniture polishes since
the materials used in the cabinet will accumulate more dust. We recommend using a non-abrasive,
antistatic cleaner and polisher.
Cleaning DECK
Digital Auto Picture
Automatically controls the video output signal for less noise depending on the tape condition.
Digital Auto Tracking
Continuously analyzes the signal and adjusts for optimum picture quality.
Manual Tracking Control
(to reduce picture noise)
Use during Playback and Slow Motion mode to reduce picture noise.
Press CH (TRACKING) / on the remote control or on DECK until the picture clears up.
To return to Auto Tracking, press POWER off, then on again a few seconds later.
V-Lock Control (to reduce picture jitter)
In Still mode, CH (TRACKING) / operate as a V-Lock control.
Features for a Quality Picture (VCR)
R
R
R
R
R
R
R
R
Built-in Head Cleaner
A clean video head helps produce a clear
picture.
So, we have equipped your DECK with
a built-in, non-chemical head cleaning system
that helps prevent clogging of the video
heads. Cleaning is performed each time you
load or unload a video cassette.
• This feature is preventative only, If your video
heads are seriously clogged, consider the use
of a chemical non-abrasive head cleaning kit
or take your DECK to a Servicenter.
Screw driver
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:126
7
Power Source: 120 V AC, 60 Hz
Power Consumption: Power On: Approx. 32 watts, Power Off: Approx. 4 watts
Video Signal: EIA Standard NTSC color
Video Recording System: 4 rotary heads helical scanning system
Audio Track: 1 track (Normal), 2 channel (Hi-Fi Audio Sound)
Tuner:
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A through I (14 ~ 22), Superband J through W (23 ~ 36)
Hyperband AA ~ EEE (37 ~ 64), Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01), Ultraband 65 ~ 94, 100 ~ 125
Input/Output Terminal: Audio/Video Line Input/Output, RF Input/Output
Input Terminal: Audio/Video Line Input (Front)
Output Terminal: S-Video Output (DVD only), Component Video Output (DVD only)
Audio Output 2 (L), (R)
Operating Temperature: 5 °C ~ 40 °C (41 °F ~ 104 °F)
Operating Humidity: 10 % ~ 75 %
Weight: 6.9 kg (15.2 lbs).
Dimensions: 430 (W) x 118 (H) x 364 (D) mm
16-15/16” (W) x 4-5/8” (H) x 14-5/16” (D) inch
Discs Played
(1) DVD-VIDEO Disc 5” (12 cm) single-sided single-layer
5” (12 cm) single-sided double-layer
5” (12 cm) double-sided double-layer (one layer per side)
3” (8 cm) single-sided single-layer
3” (8 cm) single-sided double-layer
3” (8 cm) double-sided double-layer (one layer per side)
(2) Compact Disc 5” (12 cm) disc
(CD-DA, VIDEO CD) 3” (8 cm) disc
Digital Audio Output: Digital Optical Connector
Pickup: Wavelength: 655 nm (DVD), 790 nm (Video CD/CD)
Laser power: CLASS II
Specifications
Note: • Designs and specifications are subject to change without notice.
Definition of Terms (DVD)
Angle: Some DVD discs feature scenes simultaneously shot from different angles.
The ANGLE button can be used to view the scene from different angles.
(ANGLE Indicator lights on DECK when a scene recorded at different
angles is detected.)
Chapter Number: Titles are subdivided into numbered sections. You can quickly search for
a favorite scene using these numbers.
DVD: A high-density optical disc on which high-quality pictures and sound have
been digitally recorded. DVD incorporates new video compression
technology (MPEG II) and high-density recording technology which allow
entire movies to be recorded with incredible playback quality.
Playback Control:With Video CD (version 2.0), scenes or information may be selected for
viewing or listening from an interactive menu that appears on the TV screen.
Subtitles: Written dialogue which appears at the bottom of the screen.
Time Number: The elapsed play time from the start of a disc or title. Use to quickly find
scenes. (May not work with some discs.)
Title Number: For DVD discs with two or more titles, the title is numbered as title 1, title 2, etc.
Track Number: Numbers assigned to tracks on Video CDs and CDs to allow specific tracks
to be quickly located.
Video CD: CD containing picture and sound with same quality level as video tape.
This DECK also supports Video CDs with playback control (version 2.0).
Initial Setup
(Connection)
This product incorporates copyright protection technology that is protected by method claims of
certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:127
8
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Location of Controls
Remote Control
ZOOM
p. 37
POWER
DSS/CABLE mode
p. 28
SPEED
p. 21
NUMBER keys
TV mode
p. 28
TAPE POSITION/
AUDIO CONTROL
p. 34,
40
EJECT/
OPEN/CLOSE
pp. 20,
22
ACTION
pp. 18
, 45
PAUSE
/STILL
pp. 20,
23
COUNTER
RESET
p. 32
PROGRAM
p. 24
RECORD
p. 21
ADD/DELETE/
CLEAR
pp. 19,
39, 44
VCR mode
p. 28
VOLUME
+
/
-
p. 28
CHANNEL /
TRACKING/V-LOCK
pp. 21, 6
PLAY
pp. 20,
22
REWIND/
SEARCH
/
SLOW-
pp. 20,
23
DVD mode
p. 28
INPUT
p. 35
DISPLAY
p. 11,
41
STOP
pp. 20,
22
FAST FORWARD/
SEARCH
/
SLOW+
pp. 20,
23
ANGLE
p. 37
SUB TITLE
p. 36
SURROUND/
ENTER
pp.
23,
28
MENU
p. 38
SET
VCR/TV
p. 21
RETURN
/
SEARCH
pp. 22,
30
TITLE
p. 38
AUDIO
(SAP/ Hi-Fi)
pp. 27,
36
SELECT
SKIP
SKIP
p. 23
Bold: VCR Function
Italic
:
DVD Function
Bold Italic
:
VCR and DVD Functions
Normal: Others
Light button: When Light button is pressed, (DVD, TV, VCR, PLAY, STOP, REW, FF) buttons will light
up for 5 seconds for easy button location.
If no button is pressed in 5 seconds, the light goes out to conserve the battery.
EJECT button: When this button is pressed in VCR mode, the tape is ejected. This button is inoperative if
pressed during recording. If pressed in DVD mode, the disc tray opens or closes.
Light Tower Universal Remote Control
COMMERCIAL SKIP/
ZERO
pp. 31, 32
LIGHT
p. 8
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:128
9
Front View of DECK
For assistance, call 1-800-211-PANA(7262)
If the disc cannot be removed...
First, unplug DECK. Then, prepare a rigid
wire (e.g. an extended paper clip) and,
applying moderate force, insert it straight
into the hole at the base of the tray.
The tray will eject a little. Now, pull the tray
all the way out and remove the disc.
Front View of DECK
Initial Setup
(Connection)
Bold: VCR Function
Italic
:
DVD Function
Bold Italic
:
VCR and DVD Functions
Normal: Others
Audio/Video
Input Connector 2
(LINE 2)
p. 35
CHANNEL /
TRACKING/V-LOCK
pp. 21, 6
POWER
PAUSE
p. 23
OPEN/CLOSE
p. 22
VCR/TV
p. 21
STOP/EJECT
p. 20
Multi Function
Display
p. 11
REC
p. 21
Disc Tray
Cassette
Compartment
PLAY
p. 20
Remote
Sensor
FAST FORWARD/SEARCH
p. 20
REWIND/SEARCH
p. 20
SKIP
SKIP
p. 23
PLAY
p. 22
STOP
p. 22
Over 2 inches
c
:
DVD Function
mal: Others
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:129
10
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Location of Controls (continued)
Rear View of DECK
AC Power Plug
S-Video Out
Connector
(DVD Only)
p. 10, 13
Component
Video Output Connector (Y, P
B
, P
R
)
(DVD Only)
p. 13
Audio Output 2
Connector (L/R)
p. 13
Optical Digital Audio
Output Connector
(DVD Only)
p. 15
Video Input
Connector
p. 35
Video Output
Connector
p. 12
Audio Input
Connector (L/R)
p. 35
Audio Output 1
Connector (L/R)
p. 12
VHF/UHF Antenna
Input Terminal
p. 12
VHF/UHF Antenna
Output Terminal
p.12
11
REC
1
2
:
0
0
A
M
0
:
25
CH
02
-
0
:
1
2
:
3
4
SP
S
T
ER
EO
SAP
M
ONO
VCR Status & Clock Displays
Blank Tape/ No Video Signal
Indications
Whenever a blank section of a tape
comes up in Play mode, or when the
selected channel has no broadcast
signal with Weak Signal Display
Feature (p. 33) set to OFF, the TV
screen will turn solid blue.
Function Status
Rec Time Remaining
(OTR mode only,
see p. 21.)
Current Time
Channel
Tape Speed
(See p. 6.)
Broadcast Audio
Being Received
(See p. 26.)
When a function button
is pressed, e.g. PLAY,
or you change
channels, a 5-second
display appears.
Counter
Displays (On Screen & Multi Function)
To display or remove
overlay at right,
➛➛
➛➛
➛ press DISPLAY.
A
M
VCR
VCR REC
DVD
ANGLE
VCR
Hi-Fi
TIMER
•
•
•
•
Hi-Fi Indicator
Lights up when Hi-Fi audio
is monitored in Play mode.
VCR mode Indicator
Lights up when
DECK is VCR mode.
Power Indicator
Lights up when power is on.
Clock/ Status/ Channel/ Speed Display
Displays the current time. Briefly displays VCR
status when a function button is pressed. Briefly
displays the channel number, or “L1” or “L2” when
a channel or line input is selected. Briefly displays
the recording speed when SPEED is pressed.
ANGLE Indicator
Lights up when a scene
recorded at different
angles is detected.
See p. 37. (DVD only).
DVD mode Indicator
Lights up when
DECK is DVD mode.
VCR REC Indicator
Lights up during
recording.
Multi Function Display
On Screen Displays (VCR)
VCR Indicator
Lights up when the
VCR/TV selector is
set to VCR.
Timer Indicator
Lights up when DECK is set for
Timer Recording, or when One
Touch Recording (OTR) is
used. Flashes when Timer
Recording is set, but a tape has
not been inserted into DECK and
when a power interruption
occurs during Timer
Programming.
AM
Lights up before noon.
PM is not displayed.
Function & Channel Displays
Initial Setup
(Connection)
CH 0
8
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1211
12
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections
1 Disconnect antenna or cable from TV
and connect to DECK.
WARNING
When using “Nut type” RF coaxial cables, tighten with
fingers only. Overtightening may damage terminals.
Basic Connections
• Connect DECK and TV with an RF Coaxial Cable
a
(supplied) or an AV Cable
b
(not supplied) as shown in the figure below.
• If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher
quality picture and sound.
• You can enjoy stereo sound even if your TV is not stereo by connecting a stereo
amplifier to DECK.
IN
FROM
ANT.
OUT
TO
TV
13
You CannotYou Can
• record and view
both scrambled
and unscrambled
channels if
additional
equipment is
added.
This connection
requires: two
converter boxes,
an A/B switch,
and a 2-way
splitter.
• view channel
other than the
one selected
for any type of
recording.
• do a Timer
recording of a
channel unless
you select it on
the Cable Box.
IN
FROM
ANT.
OUT
TO
TV
IN 1
VHF/UHF
OUT
IN 2IN 1
Cable Box
OUTIN
OUT 2
OUT 1
2-Way Splitter
OUT
A/B Switch
IN
■■
■■
■
Connect With Two Cable Boxes
IN
FROM
ANT.
OUT
TO
TV
IN 1
VHF/UHF
OUT
Cable Box
OUTIN
IN
R
L
OUT
TV
VIDEO
AUDIO
ANT or CATV
You CannotYou Can
• record
scrambled
channels.
• view any
(including
scrambled)
channel.
• use Remote
Control to select
channels without
using Multi-brand
control feature.
ANT
or
CATV
14
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Connections (continued)
Notes on audio output from the optical digital audio output connector
Enjoying digital audio output from the digital audio output connector
*1 The type of audio output from the connector can be selected by the Settings for DVD Opera-
tion. (See p. 46.)
*2 Sound having 96 kHz sampling is converted into 48 kHz sampling when it is output
from the DECK’s optical digital audio output connector.
For your reference:
• Dolby Digital is a digital sound compression technique developed by the Dolby Laboratories
Licensing Corporation. Supporting 5.1-channel surround sound, as well as stereo (2-channel)
sound, this technique enables a large quantity of sound data to be efficiently recorded on a disc.
• Linear PCM is a signal recording format used in CDs. While CDs are recorded in 44.1 kHz/16 bit,
DVDs are recorded in 48 kHz/16 bit up to 96 kHz/24 bit.
• If you have a Dolby Pro Logic Surround decoder, you will obtain the full benefit of Pro Logic from
the same DVD movies that provide full 5.1 channel Dolby Digital soundtracks, as well as from
titles with the Dolby Surround mark. For information on Panasonic or Technics Dolby Pro Logic
Surround Sound Decoders please contact your local dealer.
Audio Connections
Ready Checklist
Turn down the volume, then turn DECK, as well as other equipment to be connected,
off before proceeding with connection.
Do not block ventilation holes of any of the equipment and arrange them so that air can
circulate freely.
Read through the instructions before connecting other equipment.
Ensure that you observe the color coding when connecting audio and video cables.
Disc
DVD
Video CD
CD
MP3
Sound recording format
Dolby Digital
Linear PCM
(48/96 kHz 16/20/24bit)
dts
MPEG 1
Linear PCM
MP3
Optical digital audio output from connector
Dolby Digital bitstream (1-5.1 ch)
or OFF (no output)*
1
Linear PCM (2ch)
(48 kHz sampling/16 bit only)*
2
or no output*
1
Bitstream or no output*
1
PCM (44.1 kHz sampling)
Linear PCM (44.1 kHz sampling)
Linear PCM (It depends on the MP3 file)
Speaker
■ DECK
Amplifier
Speaker
Amplifier
Speaker
AUDIO OUT2
AUDIO IN
R L
L
R
Manufactured under license from Dolby Laboratories.
“Dolby,” “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.
DVD/VCR DECK
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1214
15
When DVDs recorded in Dolby Digital or dts are played, Dolby Digital bitstream or
dts bitstream is output from the DECK OPTICAL digital audio output connector.
When DECK is connected to a Dolby Digital decoder or dts decoder, you can enjoy
theater-quality audio in your home. [An optical digital audio cable (optional) is
required when an optional Dolby Digital decoder or dts decoder is used.]
Notes on connecting an optical
digital audio cable (optional)
• Firmly connect the cable to the
connector.
Caution for optical digital audio output connector:
• When connecting an amplifier (with an optical digital input connector) which does not
contain the Dolby Digital or dts decoder, be sure to select “OFF” at “Dolby Digital” and
“OFF” at “dts” of the Settings for DVD Operation “AUDIO OUTPUT” (see p. 46).
Otherwise, any attempt to play DVDs may cause such a high level of noise that it may
be harmful to your ears and damage your speakers.
• When a dts decoder is connected, please select “Bitstream” at “dts” of the Settings for
DVD Operation “AUDIO OUTPUT”.
If “OFF” is selected, there will be no sound. (See p. 46).
• Video CDs and CDs can be played as usual.
Note:
• Some dts decoders which do not support DVD-dts interface may not work properly with DECK.
Amplifier
OPTICAL
DVD/VCR DECK
Front
Speaker
Front
Speaker
Surround
Speaker
Surround
Speaker
Center
Speaker
Subwoofer
Decoder with Dolby
Digital dts processing
(optional)
Optical Digital
Audio Cable
(optional)
To Optical
Digital Audio
Input Connector
Initial Setup
(Connection)
■ DECK Dolby Digital Decoder Amplifier Speaker
or
DECK dts (digital theater systems) Decoder Amplifier Speaker
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1215
16
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before doing Initial Setup
Initial Setup for Basic Connections (Ready to Play)
Turn TV on.
See connections
a
RF Coaxial Cable Connection and
b
AV Cable Connection on p. 12.
<RF Coaxial Cable Connection>
Set TV to channel 3.
<AV Cable Connection>
Set TV to VIDEO.
[DECK
➛➛
➛➛
➛ TV]
• Go to “Doing Initial Setup (Ready to Play).” (See below.)
[Cable Box
➛➛
➛➛
➛ DECK
➛➛
➛➛
➛ TV], [DSS
➛➛
➛➛
➛ DECK
➛➛
➛➛
➛ TV]
• Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel
in your time zone.
• If you use a DSS Receiver, it must be turned off.
2
1
3
Press VCR on remote for VCR mode.
Plug DECK Power Cord into AC wall outlet. DECK comes on and auto channel
and clock set starts.
• If screen below does not appear, check DECK - TV connection and, if TV is tuned to
channel 3, try switching it to channel 4.
• To change VCR’s output channel, please refer to “VCR’s Output Channel” on p. 19.
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
CH AUTO SET PROCEEDING
CANCEL : STOP
Plugging the AC Power Plug into
an AC outlet
Doing Initial Setup (Ready to Play)
2
1
Continued on next page...
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1216
17
18
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Clock
2) Press to select
“MANUAL,” and press SET.
(For Auto Clock Set, select
“AUTO CLOCK SET.”)
3) Press and to
select, then set the date,
time, and DST (Daylight
Saving Time).
4) Press ACTION to start
Clock and exit this
mode.
(“TIME ZONE ADJUST”
appears only when auto
clock is set.)
SEL.
:
QUITTER
: ACTION
REGLER:SET
MENU
REGLAGE MAGNETOSCOPE
REGLAGE HORLOGE
REGLAGE CANAL
LANGUAGE/IDIOMA:FRANÇAIS
CA SORTIE : 3
ELEGIR
:
SALIR
: ACTION
FIJAR : SET
MENU
PREPARAR VCR
FIJAR RELOJ
FIJAR CANAL
LANGUE/LANGUAGE:ESPAÑOL
CANAL DE SALIDA : 3
SELECT
:
EXIT
: ACTION
SET:SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Language
2) Press SET repeatedly.
For English
For Spanish
For French
1) Press to select
language item.
Reset Language, Channels, Clock VCR’s
SELECT
:
EXIT
: ACTION
SET : SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
Channels
2) Press to select
“ANTENNA,” then
press SET to set your
antenna system
(“TV” or “CABLE.”)
3) Press to select
“AUTO SET,” then
press SET.
• If you use a Cable Box,
set it to the PBS channel
in your time zone.
• After Channel Auto Set
is finished, Auto Clock
Set will be performed.
1
2
Press ACTION*
to display MENU.
SELECT
:
EXIT
: ACTION
SET:SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
3) Press ACTION to exit.
SELECT :
EXIT
: ACTION
SET:SET
MENU
SET UP VCR
SET CLOCK
SET UP CHANNEL
IDIOMA/LANGUE : ENGLISH
VCR’S OUTPUT CH:3
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
ANT
ENN
A
:
CABLE
A
U
T
O
S
E
T
W
EA
K
S
I
GN
AL
D
I
SPLA
Y
:
OFF
C
ABLE
/
DSS
B
O
X SET UP
V
CR
Plus
+
C
H SET UP
SET UP
CH
A
NNE
L
AUT
O
C
L
OC
K SET
M
A
NUNU
AL
T
I
M
E
ZO
N
E
A
D
JUS
T
:
0
SELE
C
T
:
SET
:
SET
EXIT
:
ACT
I
O
N
SET
C
L
OC
K
D
ST
:
ON
9
/
30
/
2002
SUN
12
:
0
0
P
M
SELECT
H
OUROUR
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
SET
C
L
OC
K
SELE
C
T
:
SET
:
SET BACK :
EXIT
:
ACT
I
O
N
1) Press to select
“SET UP CHANNEL,”
and press SET.
1) Press to select
“SET CLOCK,” and
press SET.
• PROGRAM functions are not available
when using COMPONENT Video Output
and S-VIDEO OUT. Please set TV to
either RF INPUT or VIDEO INPUT, and
then press PROGAM.
CH AUTO SET PROCEEDING
CANCEL : STOP
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1218
19
Add or Delete a Channel
To add channel:
Select channel with NUMBER keys
and press ADD/DLT.
To delete channel:
Select channel with CH / or
NUMBER keys and press ADD/DLT.
C
HANNEL
08
ADDED
C
HANNEL
08
DE
L
E
T
ED
Time Zone Adjust
2) Press to select
“TIME ZONE ADJUST,”
VCR’s Output
Channel
1) Press to select
“VCR’S OUTPUT CH.,”
and press SET.
SELECT
:
EXIT
: ACTION
SET : SET
20
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Playback/ Record on a Tape
PAUSE/
STILL
REW/SLOW-
STOP
FF/SLOW+
EJECT
Insert a tape.
21
Playback using DECK buttons
Press PLAY.
CH /
SPEED
REC
VCR/TV
21
Insert a tape with a record tab (p. 6).
1
• DECK power comes on.
The VCR mode and “VCR” indicator light up
on Multi Function Display.
5
4
2
3
Press CH , or NUMBER keys
to select the channel.
• For “LINE” input, see p. 35.
• If channel is over 100, press 100 key then press
the remaining 2 digits.
Press SPEED
to select the record speed (p. 6).
SP = Standard Play LP = Long Play
SLP = Super Long Play
Press REC
to start recording.
(The VCR REC indicator lights up on Multi Function
Display),
• To edit out unwanted scenes, press PAUSE/STILL
to pause, and again to resume recording.
• You cannot view another channel during recording.
Press STOP
to stop recording.
• It is not possible to record from DVD/ Video
CD/ CD to VHS tape using DECK.
• Watching one channel and recording another
is not possible when using Cable Box or
DSS Receiver.
• After 5 minutes in Pause mode, DECK stops to
protect a tape and video heads.
• Speed appears on-screen and on Multi Function Display.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
Record on a Tape
Remove loose or peeling
labels from tapes to prevent
tape jam.
Multi Function Display
Record using DECK buttons
4
2
Select
Channel.
VCR/TV
Press REC
to start
Recording.
Press STOP/EJECT to stop.
This video recorder, equipped with HQ
(High Quality) system, is compatible
with existing VHS equipment. Only use
tapes with the mark. Only tapes
tested and inspected for use in 2, 4, 6,
and 8 hour machines are
recommended.
Normal Rec
0:30 1:00
1:302:003:004:00
1
Insert a tape.
Note
Notes
Basic
Operation
One Touch Recording (recording in progress),
➛➛
➛➛
➛ Press REC repeatedly to set the recording length
➛➛
➛➛
➛ (30 min. ~ 4 hours).
• DECK shuts off after the preset record length.
Record one station, watch another,
➛➛
➛➛
➛ press VCR/TV
(“VCR” goes out on Multi Function Display),
➛➛
➛➛
➛ select channels at TV (recording continues).
Select Channels at DECK (In STOP or
REC. PAUSE mode),
➛➛
➛➛
➛ press VCR/TV
(“VCR” lights up on Multi Function Display),
➛➛
➛➛
➛ select channels at DECK.
Play a disc while recording a tape.
➛➛
➛➛
➛ insert a disc during recording,
➛➛
➛➛
➛ press
DVD
, and then press
PLAY
.
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1221
22
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Basic DVD Operation
Ready Checklist
All connections are made. (pp. 12 ~ 15)
DECK is plugged in.
If DECK is connected to an audio amplifier,
turn the stereo system’s power on.
*
1
Interactive DVD...
May include multiple camera angles,
stories, etc.
*
2
Video CD with playback control...
Particular scenes or information can be
interactively selected from a menu that
appears on the screen.
Operation using DECK buttons
Press PLAY.
Insert a disc.
Press
OPEN/CLOSE.
Press STOP.6
Press
POWER
4
1
3
3, 7
OPEN/
CLOSE
10
MENU
SET
FF/
SLOW+
STOP
RETURN
POWER
REW/
SLOW-
NUMBER
keys
TITLE
PLAY
DVD
PAUSE/
STILL
SELECT
SURROUND
SKIP
SKIP
5
Press or
NUMBER keys
(see
below) to select title,
and
press
SET
to play.
1
Press
POWER*
on the remote or DECK.
Press
DVD
to select DVD mode.
Press
OPEN/CLOSE
,
and then place a disc into the disc tray.
2
3
• If a disc is already inserted, go to step 4.
(Depending on the disc, playback may
start automatically.)
Press
PLAY
to start playing.
Disc tray closes automatically.
4
1
2
If an interactive DVD*
1
or
a Video CD with playback
control*
2
is used and TITLE
MENU appears, go to step 5.
• You may also close tray by
pressing
OPEN/CLOSE
.
• Data reading time differs with
each disc.
Using NUMBER keys starts playing automatically.
<Example> 1 digit number 1 ••• 1
2 digit number 12 ••• 10 1 2
3 digit number 123 •••100 1 2 3
Press
SKIP
| or | to go to next or previous
menu screen.
• SKIP function not available with all discs.
Please refer to disc jacket for operation information.
<Example>
<Example>
To return to menu (play stops)
Press
TITLE, MENU,
or
RETURN
. (DVD)
Press
RETURN
. (Video CD)
Press
STOP
to stop playing.
6
7
Press
OPEN/CLOSE
to eject the disc.
• Hold disc by its edges
only (p. 4) with printed
side up and use guides to
place into tray.
Use 3”(8 cm)
or 5” (12 cm) disc.
2
1
CLOSE
READING
T
I
TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
T
I
TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
Dogs
of the world
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1222
23
• Please read the disc jacket for operation
information.
• If a single sided disc is placed in upside
down, “PLEASE CHECK THE DISC, AND
FOR STAINS OR SCRATCHES ON
DISC” is displayed.
• Remove disc and press DECK POWER
off when not in use.
• Disc continues to rotate with menu
displayed even after play is done.
Press STOP to clear menu display when
finished with menu.
■ Forward/Reverse Scene Search
Press
FF/SLOW+
or
REW/SLOW-
during play.
Press
PLAY
to release.
• Starting forward/reverse search during play
started from menu on Video CDs may recall
menu.
• Search speed, slow at first, increases with each
additional press of the button up to 5 levels.
■ Forward/Reverse Chapter/Track Skip
Press
SKIP
| or |
SKIP
during play.
Each press skips a chapter (DVD) or
track (Video CD/CD).
• Pressing |
SKIP
once midway through a
chapter/track returns to the start of that
chapter/track. Each additional press skips
back one chapter/track.
• Pressing
SKIP
| or | during play started
from menu on Video CDs may recall menu.
■ Still Picture or Pause
Press
PAUSE/STILL
during play.
Press
PLAY
to release.
• DVD/Video CD : DECK will enter still picture
mode.
• CD : DECK will enter pause mode.
■ Frame by Frame Picture
(DVD/Video CD)
Press
PAUSE/STILL
in still mode.
Press
PLAY
to release.
• Each press advances picture one frame.
• Hold button down for consecutive frame advance.
• Whether pictures are advanced by “FRAME” or
“FIELD” is selected automatically. (See p. 47)
■ Slow Motion Picture (DVD/Video CD)
Press
FF/SLOW+
or
REW/SLOW-
in still mode.
Press
PLAY
to release.
• Slow motion speed, slow at first, is increased
with each additional press of the button up to
5 levels.
• Reverse slow motion is not available for Video
CDs.
• When appears on the screen while a button
is being operated, it means that the
corresponding operation is prohibited by DECK
or the disc.
DECK memorizes the point where STOP is
pressed ( flashes on screen).
Press
PLAY
to resume play from this point.
Pressing
STOP
again or opening the tray
cancels RESUME, however, RESUME is not
canceled when power is turned off and on.
• RESUME works only with discs for which
elapsed play time is displayed during play.
Resume Function
Notes
Power turns off after DECK has been in
Stop mode (DVD) for about 5 minutes.
Auto-Power Off Function
1. Do steps 1-4 (previous page).
When menu appears, press
STOP
.
2. Press
NUMBER keys
to select desired
track (play begins).
• Check disc for track numbers.
• Press “1” to start at beginning of disc.
To Resume Menu use,
Press
STOP
and press
PLAY
, then the
menu will be displayed.
Now, go to step 5 (previous page).
Enjoy Video CDs featuring
playback control without using
menus (Video CDs only)
*Important: If a remote control button does not work when pressed,
press the DVD button on the remote and try the button again.
Surround Sound System
Press
SURROUND
to set Surround sound.
To cancel,
press
SURROUND
.
• Surround sound effects is available in
DVD mode only.
Note
SURROUND ON
SURROUND OFF
Reverse Skip Forward Skip
Current playback position
Chapter/Track Chapter/Track Chapter/
T
rackChapter/
T
rack
Basic
Operation
ps)
RN
. (DVD)
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1223
24
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Timer Recording
ADD/DLT
Press PROG*
to display Program.
Press PROG
to end programming.
3
1
DAILY
13
1
31
12
SELECT /
Selection Order
WEEKLY
(SAT)
WEEKLY
(MON)
WEEKLY
(SUN)
14
Example
Today
2) To set remaining items,
press
to select and
press SET
to set START/ STOP times,
CH(channel) or LINE input
(p. 35), and tape speed
(SP, LP, SLP).
To Enter More Programs,
press
to select and
press SET
to set an unused program
number, and then repeat
step 2.
Or
Press PROG
to exit.
1) To set record DATE,
press
to select:
1~31= one time, or
DAILY= MON~ FRI, or
WEEKLY= same time
each week and
press SET.
• See selection order left.
SE
SE
L
E
C
T
START
D
AT
E
13
SUN
--:--
--:--
--
T
OD
A
Y
DATE START ST
O
P
C
H
SLP
SELE
C
T
:
SET
:
SET
END
:
P
R
O
G
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
DT
STA
R
T
ST
O
P
CH
SPD
13 10
:
00
P
12
:
00
P
0
2
SP
--
--
:
--
--
:
--
--
--
--
--
:
--
--
:
--
--
--
--
--
:
--
--
:
--
--
--
C
AN
C
EL
:
A
DD
/
DLT
SELECT 1-8
:
E
NTER
: SET
EXIT
:
P
R
O
G
POWER
SET
PROG
SELECT
Ready Checklist
All connections are made (pp. 12 ~ 15).
TV and DECK are plugged in.
Clock set correctly.
Tape has rec.tab. (p. 6)
Remote is in VCR mode. (Press VCR.)
Sufficient tape remaining for rec time.
• The “Timer” Indicator lights up on DECK.
• You can do Timer Recording with the power on or off.
•“TIMER REC WILL START SOON” appears on-screen for 2 minutes
before Timer Recording starts. If DECK is in DVD mode, no message
appears, but the VCR REC Indicator, the VCR mode indicator and
“REC” will flash on Multi function Display.
VCR REC Indicator
VCR mode Indicator
A
M
VCR
VCR REC
DVD
ANGLE
VCR
Hi-Fi
TIMER
•
•
•
•
Multi Function Display
TIMER Indicator
2
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1224
25
To Replace program...
To Clear program...
Review, Replace or Clear Program Contents:
(Recording is not in progress)
or
Important notes when using DSS Receiver
• When recording programs via DSS Receiver, DSS Receiver must be left on.
• When recording programs via an antenna or cable, DSS Receiver must be turned off.
C
AN
C
EL
:
A
DD
/
DLT
SELECT
1-8 :
ENTER : SET
EXIT
: PROG
DT
STA
R
T
ST
O
P
CH
SPD
7 9
:
00
A
12
:
00
A
08
SP
8
10
:
00
P
12
:
00
P
02
SP
10
8
:
00
P
9
:
00
P
10
SP
S
U
9
:
00
P
10
:
00
P
L1
LP
C
AN
C
EL
:
A
DD
/
DLT
SELECT
1-8 :
ENTER : SET
EXIT
: PROG
DT
STA
R
T
ST
O
P
CH
SPD
--
--
:
--
--
:
--
--
--
8
10
:
00
P
12
:
00
P
02
SP
10
8
:
00
P
9
:
00
P
10
SP
S
U
9
:
00
P
10
:
00
P
L1
LP
Press ADD/DLT.
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
1
2
3
Press
to select number and
press SET
to display.
To cancel a Timer
Recording in progress...
Repeat Step 2 (p. 24)
to set new programs.
Press PROG
to end the programming.
Hold down STOP on VCR mode for
a few seconds to cancel the Timer
Recording.
(The “TIMER” Indicator goes out
on Multi Function Display.)
• Any future daily or weekly recording
will be performed as programmed.
7
SUN
9
:
00A
12
:
00A
08
T
OD
A
Y
----------------------------------------
DATE
S
TART
S
TOP
CH
SP
SE
L
E
C
T
START
D
AT
E
SELE
C
T
:
SET
:
SET
BACK :
END
:
P
R
O
G
Notes
• If you are using a Cable Box, the VCR’s channel for Timer Recording must be set to
the Cable Box intput channel and Cable Box must be manually set to the desired
channel. Cable Box power must be left on.
• 2 minutes before Timer Recording is performed, “PLEASE PREPARE FOR TIMER
REC” appears and Timer Indicator flashes.
Be sure a cassette with record tab is loaded and DECK is in Stop mode.
• If a power interruption occurs while programming the timer, the timer program(s) may be
canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION”
appears on-screen, please re-enter the timer programs.
• If the start time for Timer Recording comes up during recording and playing back,
Timer Recording will not be performed.
Press PROG
to display Program List.
4
VCR
Operation
PV-D4732S P1-25 (2nd) [LSQT0618B].p65 2002/05/23, 18:1325
26
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
MONO broadcast
Normal monaural sound broadcast.
SAP broadcast
Secondary Audio Program (sub
language) broadcast. Select SAP
audio mode for the sub language.
MTS Stereo broadcast
Multi-channel Television Sound
Stereo broadcast. Select STEREO
audio mode.
• If stereo broadcast is weak and
display flickers, select MONO audio
mode for possible better results.
MTS Stereo and SAP broadcast
Multi-channel Television Sound
Stereo (main language) and
Secondary Audio Program (sub
language) broadcasts are being
received simultaneously.
Select STEREO or SAP audio mode.
The following are possible audio broadcast types and on-
screen displays.
The signal being received is indicated with an “
” mark
while the selected audio mode is indicated with an arrow.
Receivable Broadcast Types
MTS Broadcast/ VHS Hi-Fi Stereo System
Equipped with
®
-TV
Noise Reduction for
true MTS reproduction.
®
-TV Noise
Reduction is required
for good stereo
separation and audio
fidelity.
®
is a
registered trademark,
and is licensed by
®
Technology Licensing.
Connection
Make the Audio/Video Connection as shown on pp. 12 ~ 15.
• You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV.
To display the broadcast signal being received,
➛➛
➛➛
➛ press DISPLAY*.
AUDIO
(SAP/Hi-Fi)
DISPLAY
ST
OP
1
2
:
0
0
A
M
CH
02
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
CH
02
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
CH
02
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
ST
OP
1
2
:
0
0
A
M
CH
02
0
:
0
0
:
0
0
SP
STER
EO
SAP
M
ONO
PV-D4732S P26-35 (2nd) [LSQT0618B].p65 2002/05/23, 18:1326
27
Audio Mode for Recording
1
2
Do a recording.
See p. 21.
3
Audio Mode for Playback
Start playback.
See p. 20.
• Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. Standard
stereo tapes will playback in monaural sound.
• To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to
a stereo TV or an external stereo amplifier and speakers. (See pp. 12, 14, 15.)
• If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio.
• Hi-Fi and normal audio playback volume level may differ.
• Arrow indicates
selection.
• Refer to “Receivable Broadcast Types” on p. 26.
• Arrow indicates selection.
• Select “HIFI (L/R)” or “HIFI (L)” or “HIFI (R)” to listen to stereo
recordings in stereo sound.
Select “NORMAL” for monaural sound.
• Display disappears after 5 seconds.
Press AUDIO (SAP/Hi-Fi)
to display audio mode.
(Display disappears after 5 seconds.)
Press AUDIO (SAP/Hi-Fi) repeatedly
to select desired mode.
Press AUDIO (SAP/Hi-Fi)
to display audio mode.
Press AUDIO (SAP/Hi-Fi) repeatedly
to select desired mode.
STER
EO
SAP
M
ONO
Notes
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
VCR
Operation
1
2
3
H
I
F
I
: L
/
R
H
I
F
I
: L
H
I
F
I
:
R
N
ORM
AL
PV-D4732S P26-35 (2nd) [LSQT0618B].p65 2002/05/23, 18:1327
28
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Multi-Brand Control Feature
The Remote Control can be set to control some TV and
Cable Box/DSS functions.
Find your TV and Cable Box/DSS Receiver
Brand Code Number on the following page.
Setup for TV control,
➛➛
➛➛
➛ hold down TV button,
➛➛
➛➛
➛ enter code with NUMBER keys.
Multi-Brand Control Setup
Confirm code entry,
➛ press POWER to turn selected unit on or off.
• See table below for controllable functions in each mode.
Setup for Cable or DSS control,
➛➛
➛➛
➛ hold down DSS/CABLE button,
➛➛
➛➛
➛ enter code with NUMBER keys.
• If code number is 100 or greater,
➛ e.g., press 1 - 0 - 2 for 102.
3
1
• Repeat setup after remote battery replacement.
• Remote will not control every TV, Cable Box, or
DSS made by the manufacturer listed. If you get
no response, your particular unit cannot be
controlled. There are NO additional codes for the
products listed. If your product is not listed, then
the remote is not compatible with that product.
Notes
2
Mode
Unit
DVD/VCR TV
DVD/VCR
TV
All
POWER, INPUT,
NUMBER keys,
ENTER,
CH / ,
VOL
+
/
-
EJECT/
OPEN/CLOSE
*,
DISPLAY
,
PLAY
,
STOP
,
FF/SLOW+
,
REW/SLOW-
,
VCR/TV, PAUSE
/STILL
,
SKIP
,
AUDIO
, CM/ZERO,
TAPE POSITION,
COUNTER RESET , SPEED,
REC
After remote is set up, you can select VCR, DVD, TV, or
DSS/CABLE for the desired function.
Press VCR,
DVD
, TV, or DSS/CABLE on the remote.
(Table below shows available remote buttons for each mode.)
CABLE/ DSS
Using Multi-Brand Control
CABLE/
DSS
POWER, ENTER,
NUMBER keys
(except 100key),
CH /
• Not all functions listed may be controllable.
• In TV or DSS/CABLE mode, it may be necessary to press ENTER after pressing
NUMBER keys for channel selection.
Notes
VOL
+
/
-
VOL +/-
* Bold: VCR Function
Bold Italic: VCR and DVD Functions
Italic: DVD Function
Normal: TV, Cable Box or DSS Receiver
DSS/
CABLE
POWER
ENTER
NUMBER
keys
TV
VCR
DVD
PV-D4732S P26-35 (2nd) [LSQT0618B].p65 2002/05/23, 18:1328
29
• Due to changes in infra-red commands used by manufacturers, some brands have several
codes. If your unit does not respond to the first code, please try the next one.
• Some TV, Cable Box and DSS Receiver brands require you to turn on the power manually.
Cable Box Brand Code Numbers
Panasonic ....................... 01, 02
Quasar ............................ 01, 02
RCA ....................................... 03
GE ......................................... 03
Zenith .................................... 04
Magnavox .............................. 05
TV Brand Code Numbers
Sylvania ................................ 05
Sharp ............................... 06, 07
Sony ...................................... 08
Toshiba ................................. 09
Sanyo .................................... 10
Fisher .................................... 10
JVC ........................................ 11
Hitachi ................................... 12
Mitsubishi ........................ 07, 13
Samsung ............................... 14
Gold Star ................... 15, 16, 17
DSS Brand Code Numbers
Important Notes
Archer ......................... 44, 06, 01, 120, 05, 63, 126
Cableview ................ 29, 09, 01, 63, 120, 44, 42, 30
52, 04, 124, 126
Citizen ................... 44, 52, 30, 63, 42, 04, 124, 126
Curtis ..................................... 08, 09, 25, 61, 53, 87
Century ...................................... 44, 51, 75, 59, 126
Cabletenna .................. 29, 09, 01, 63, 120, 44, 126
Cable Cinema .............. 29, 09, 01, 63, 120, 44, 126
Diamond ...................... 29, 09, 01, 63, 120, 44, 126
Eagle ....................... 62, 40, 22, 13, 58, 20, 26, 107
Eastern ................................................... 28, 29, 130
Explorer .................................. 08, 09, 25, 61, 53, 87
Gemini ..................................................... 30, 04, 124
General Electric ...................................... 01, 57, 120
General Instruments . 01, 84, 83, 34, 03, 02, 04, 55
65, 66, 67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Gerrard ............................................... 44, 51, 75, 59
GC Electronics ............... 44, 42, 63, 29, 30, 52, 04
124, 126
Hamlin ............... 41, 14, 15, 28, 102, 104, 103, 130
Hitachi ................................................................... 31
Jerrold .......... 01, 84, 83, 34, 03, 02, 04, 55, 65, 66
67, 68, 120, 106, 121, 122, 115, 117, 118, 124
Jasco ...................................................... 30, 04, 124
Macom ................................................................... 31
Magnavox ...................................................... 26, 112
Matsushita ................................. 17, 16, 08, 87, 109
Movietime ...................... 32, 39, 42, 44, 126, 38, 40
Maestro ........................................................... 74, 35
NEC .................................................... 40, 19, 38, 32
NSC .................................................... 40, 19, 38, 32
Novavision ............................. 08, 09, 25, 61, 53, 87
Next Level ........... 01, 84, 83, 34, 03, 02, 04, 55, 65
66, 67, 68, 120, 106, 121, 122
Oak................................................. 46, 11, 129, 101
Oak Sigma ..................................... 46, 11, 129, 101
Panasonic .................................. 17, 16, 08, 87, 109
Philips ................... 23, 24, 20, 13, 07, 50, 128, 129
Pioneer ...................................................... 06, 05, 12
Pulsar .................... 04, 42, 63, 44, 30, 52, 124, 126
Quest ........................................................ 06, 05, 12
Radio Shack ............................... 44, 51, 75, 59, 126
RCA ............................................ 17, 16, 08, 87, 109
Realistic ..................................... 44, 51, 75, 59, 126
Recoton ...................................... 44, 51, 75, 59, 126
Regal ................. 41, 14, 15, 28, 102, 104, 103, 130
Regency .................................................. 28, 29, 130
Rembrandt ....... 44, 42, 63, 29, 01, 32, 39, 120, 126
Samsung ...................................... 42, 06, 32, 05, 40
Scientific Atlanta ................... 08, 09, 25, 61, 53, 87
Sheritech ............................................................... 27
Signal ............................................................ 26, 112
SL Marx ............. 42, 06, 32, 40, 43, 44, 52, 63, 126
Sprucer ...................................... 17, 16, 08, 87, 109
Standard Components ............... 32, 39, 42, 44, 126
Stargate .............. 04, 42, 32, 40, 63, 44, 30, 52, 06
124, 126
Sylvania .......................................................... 19, 18
Teknika ........................................................... 74, 35
Telecaption .................................................... 77, 127
Teleview ................................. 40, 19, 38, 32, 42, 06
Texscan .......................................................... 19, 18
Tocom ................................... 34, 33, 01, 42, 66, 120
Toshiba ................................................................. 36
Unika ........................... 44, 42, 63, 29, 01, 126, 120
Universal .............................. 52, 43, 44, 63, 42, 126
Viewstar .................. 62, 40, 22, 13, 58, 20, 26, 107
Videoway .......................................... 07, 23, 50, 129
Vidtek .................................................................... 64
Zenith ............................................... 07, 23, 50, 129
Toshiba ....................................................... 90
Hitachi/ Hughes.................................... 91, 99
Primestar .................................................... 92
Drake .......................................................... 93
Magnavox ............................................. 94, 95
Uniden................................................... 94, 95
Optimus ................................................ 94, 95
Panasonic ................................................... 96
ProScan ...................................................... 97
RCA ............................................................. 97
SONY .................................................. 98, 105
VCR
Operation
PV-D4732S P26-35 (2nd) [LSQT0618B].p65 2002/05/23, 18:1329
30
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Index Search
Note
• If Index Search is started very close to an
index mark, that index mark may not be
counted in the search.
1
2
Tape Operation
Search System
For each recording, an invisible index mark is placed on the tape. A program index and
information are also included for timer recordings. These marks are used to access or
scan recordings.
1
Program End Search
2
Fig. 1
Fig. 2
Fig. 3
Note
Locates end point of recording for continuity.
Examples of Program End Search.
If search exceeds
a few seconds in
BLANK area.
➛➛
➛➛
➛ search continues 7 sec. past end point,
➛➛
➛➛
➛ tape rewinds to 10 sec. before end point,
➛➛
➛➛
➛ tape plays to end point and stops.
Upon locating end point,
• If Program End Search is started very close to
an index mark, that mark may be skipped
over.
PROGRAM END SEARCH
SEARCH START : FF
EXIT
:SEARCH
Program 2 or BLANK
Program 1
the current tape position
Press SEARCH button
FF
INDEX
End Point
Program 2
Program 1
the current tape position
Press SEARCH button
31
NUMBER
keys
Auto Play
Insert a tape ➛ Power comes on,
➛ Play starts if there is no record tab
(see p. 6).
Auto Rewind
Play
Fast Forward
Play Auto Eject
(Repeat Play must be off)
Play
➛ ➛
➛ ➛
➛ Tape end
➛ ➛
➛ ➛
➛ Rewind
➛ ➛
➛ ➛
➛ Tape ejects if there is no record tab
Auto Operation Functions
Commercial Skip
VCR fast forwards (skips) over 1~3 minutes
of recorded tape.
1
Press CM/ZERO in Play mode.
PLAY
1st Press
2nd Press
3rd Press
1 min Skip
2 min Skip
3 min Skip
*Important: If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.
• No indication appears on-screen.
• The skip time can be changed by
pressing CM/ZERO repeatedly as
shown by the figure below.
REW/SLOW-
FF/SLOW+
PLAY
SEARCH
CM/ZERO
STOP
VCR
Operation
➛ Tape end ➛ Rewind
PV-D4732S P26-35 (2nd) [LSQT0618B].p65 2002/05/23, 18:1331
33
35
Copying Your Tapes (Dubbing)
1
Insert a pre-recorded tape.
2
Insert a blank tape with record tab.
Press REC, then PAUSE/STILL
immediately to enter REC/PAUSE
mode.
3
Press INPUT to set DECK Input mode to
LINE for Video Input.
(See “Selecting the Input Mode” below.)
4
Press PLAY to start dubbing.
Playing VCR starts playback.
Press PAUSE/STILL to start dubbing.
DECK starts recording.
Press STOP to stop dubbing.
Caution:• Unauthorized exchanging and/or copying of copyrighted recordings may be
copyright infringement.
• Please note that some tapes cannot be dubbed on DECK. Also, it is not
possible to dub DVD/ Video CD/ CD to VHS tapes using DECK.
Playing (Source) VCR Recording (Editing) DECK
5
To Monitor Dubbing on TV
1 Turn TV on and tune to the Recording
VCR channel (CH 3 or CH 4).
2 Set the VCR/TV Selector on DECK to
“VCR.”
Note
• Dubbing tapes protected with Copy
Guard will result in poor quality
recordings.
Connection
Press STOP to stop dubbing.
Press PLAY, then PAUSE/STILL
immediately to enter PLAY/PAUSE
mode.
The operation of steps 4 and 5 must be done on the
playing and recording VCRs at the same time.
Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK.
To monitor the dubbing, also connect TV as shown.
Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R”
AUDIO IN terminals on DECK.
In place of Playing VCR, you can use other equipment, such as a Camcorder.
Simply connect the unit’s Audio/Video outputs to DECK.
Selecting the Input Mode
Method 1: Press INPUT repeatedly.
Channel Number
↔↔
↔↔
↔ LINE1
↔↔
↔↔
↔ LINE2
Method 2: Press CH / .
Display will change as below.
Front of DECK
VIDEO IN 2
L-AUDIO IN2-R
(Audio/Video In Terminals
on the front of DECK are
available)
IN
FROM
ANT.
OUT
TO
TV
IN 1
VHF/UHF
OUT
TV
OUT
VHF/
UHF
DVD/VCR DECK
VIDEO
AUDIO
1
L
R
VCR/ Camcorder (Hi-Fi)
VIDEO
AUDIO
L
R
•“L1” or “L2” lights up on Multi Function Display
(about 4 seconds) when LINE1 or LINE2 is selected.
• LINE1: For rear audio/video connection.
LINE2: For front audio/video connection.
1
2
VCR
Operation
1
2
3
125
LINE1
(CABLE)
69
(TV)
or
LINE2
Press
Press
PV-D4732S P26-35 (2nd) [LSQT0618B].p65 2002/05/23, 18:1335
36
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
AUDIO: 3 ESP
3 ESP
Dolby Digital 3/2.1ch
SELECT
SELECT
: SE
SE
T:
T:
SET
SET
Hola
AUDIO: 1 ENG
1 ENG
Dolby Digital 3/2.1ch
SELECT
SELECT
: SE
SE
T:
T:
SET
SET
Hello
37
When appears on the screen while
a button is being operated, it means
that the corresponding operation is
prohibited by DECK or the disc.
• The ANGLE Indicator lights up on
DECK when a scene recorded
at different angles is detected.
• The angle number can be set
beforehand so that the angle is
switched whenever the ANGLE
Indicator lights up.
ANGLE Indicator
• DVD Karaoke (1 vocal) VOCAL ON VOCAL OFF
• DVD Karaoke (2 vocals) VOCAL V1
+
V2 VOCAL V1 VOCAL V2 VOCAL OFF
• Video CD LR L R
1
Press
AUDIO
in Play mode
to display the audio screen.
Vocal Selection for Karaoke Discs
(DVD/Video CD)
DVDs may contain scenes shot from multiple camera
angles allowing the same scene to be viewed at different
angles. You can view these angles, if available, using the
ANGLE button.
1
Press
ANGLE
in Play mode to display the
angle selection on-screen.
• Display disappears after
5 seconds.
Multiple Angle Viewing (DVD only)
2
Press
to select the desired
angle.
2
Press (or )
to select as shown below,
and
press
(or ) to set.
(DVD only)
Number of angle being played back.
ANGLE : 1
SELECT : SET:SET
SELECT : SET : SET
AUDIO:2 ENG VOCAL ON
VOCAL ON
You can enlarge specific portions of a picture and
select the zoom ratio using the ZOOM button during
DVD playback.
Press
ZOOM
repeatedly to change display
as follows.
Picture Zoom (DVD only)
• You can enlarge the center portion of the image
to one of 2 magnifications.
• The subtitle cannot be enlarged nor
can it’s position be changed.
• The picture zoom feature does not
work with a Video CD.
• During picture zoom, “ZOOM1” or
“ZOOM2” is displayed on-screen.
• Zooming, on some discs, may result
in poor picture quality, or may not
operate at all.
38
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Some DVDs have more than one title, e.g. movies.
If the disc offers a title menu, you can select the desired
title number. (Operation may vary according to the disc.)
1
Press
TITLE
*
in Play mode
to display the title screen.
Title Menu (DVD only)
DVDs may offer a special menu. This menu may include
guides to unique contents, audio/subtitle languages, etc.
Although contents and operation may vary, the following
steps show basic steps for using the menu.
1
2
Press
MENU
in Play mode to display
DVD MENU.
Press or
NUMBER keys
to select an item, and
press
SET
or
PLAY
to perform.
DVD Menu (DVD only)
2
Press or
NUMBER keys
to select a title, and
press
SET
or
PLAY
to start playing.
Disc Operation (continued)
•“Pressing
SET
or
PLAY
” is
not necessary when using
NUMBER keys.
<Example>
<Example>
<Example>
T I TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
T
I
TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
DVD MENU
3 . ANGLE
1 . SUBT
I
TLE
2 . AUD
I
O
DVD MENU
3 . ANGLE
1 . SUBT
I
TLE
2 . AUD
I
O
B
i
rds
of the world
<Example>
Repeat step 2 if there is
more than one menu.
•“Pressing
SET
or
PLAY
” is
not necessary when using
NUMBER keys.
MENU
SET
STOP
PLAY
NUMBER
keys
TITLE
CLEAR
ACTION
SELECT
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1338
39
You can program specific tracks and order of play.
Program Play (Video CD/CD)
Ready Checklist
DECK is in DVD mode, press DVD.
Video CD or CD is inserted.
1
Press
ACTION
to display MENU.
2
Press
to select
“PLAY MODE,” and
press
SET
to display.
3
Press
to select
“PROGRAM PLAY,”
and
press
SET
to display.
5
Press
to select “START,” and
press
SET
to start play
of programs in the
sequence selected.
• To cancel, press
STOP
during play, then press
CLEAR
.
4
Press
to select a track
number (Track
numbers on disc are
displayed.), and
press
SET
.
• Repeat step 4 to select another track.
• The selected track is added on the right side.
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
40
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Tracks are played in a random order.
Random Play (Video CD/CD)
Press
ACTION
*
to display MENU.
1
Disc Operation (continued)
Pess
to select “PLAY MODE,”
and
press
SET
to display.
2
DVD MAIN MENU
SELECT :
SET : SET
END : ACTI ON
DISC LANGUAGES
AUDIO OUTPUT
ST I LL MODE : F I E L D
TV MODE : L e tt e rb o x 4 :3
PARENTAL
LOCK
:
LEVEL 8
PLAY MODE
PLAY MODE
Press
to select
“RANDOM PLAY,” and
press
SET
to begin random play.
• To cancel, press
STOP
during play, then press
CLEAR
.
3
PLAY MODE
SELECT :
SET : SET
END : ACTI ON
PROGRAM PLAY
RANDOM PLAY
*Important:
If a remote control button does not
work when pressed, press the
DVD button on the remote and try
the button again.
SELECT
STOP
CLEAR
ACTION
SET
AUDIO
CONTROL
Ready Checklist
DECK is in DVD mode, press DVD.
Setting the Sound Output Level
Press
AUDIO CONTROL
repeatedly to change “ON”
↔↔
↔↔
↔ “OFF.”
•“ON” or “OFF” lights up on Multi Function Display (about 3 seconds) when
press AUDIO CONTROL.
DVD /Video CD
Music CD
Audio Control “OFF”
Volume level is low.
Audio Control “ON”
Volume level is increased
automatically when played back.
•“ON” is set ..... When a DVD or Video CD is played back, the average volume is increased.
•“OFF” is set .... The volume level recorded on the disc is played back just as it is.
• When audio equipment is connected, setting the Sound Output level to “OFF” is recommended.
• If the sound becomes abnormal while playing a disc, set the Sound Output level to “OFF.”
Notes
Audio recorded on a DVD or Video CD often incorporates
a dynamic range of sound.
This means that, when compared to a music CD, etc.,
the average volume is generally lower and the peaks
may be higher. This unit can be set so that the average
volume is increased automatically.
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1340
41
42
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
DVD Operation using On-Screen Displays (continued)
Detailed Descriptions of each On-Screen Display
■■
■■
■ Disc information screen (for DVD)
1. TITLE No.
• Change the No. by pressing * or
NUMBER keys
, and press
SET
.
2. Chapter No.
• Change the No. by pressing or
NUMBER keys
, and press
SET
.
3. Disc currently being played
4. Elapsed playing time
The screen may be changed by selecting the elapsed time.
• Change the elapsed time by pressing
NUMBER keys
.
e.g., press 0 - 1 - 2 - 3 - 4 - 5 for 01 : 23 : 45.
• This function does not work with some discs.
■■
■■
■ Disc information screen (for Video CD/ CD)
A.Track No.
• Change the No. by pressing or
NUMBER keys
, and press
SET
.
B.Playback control ON/OFF
[Video CD with playback control only]
C.Disc currently being played
D.Elapsed playing time
TITLE
chapter
chapter
chapter
CHAPTER REPEAT
TITLE REPEAT
NORMAL PLAY
CURRENT PLAYBACK POSITION
track
track
track
TRACK REPEAT
DISK REPEAT
NORMAL PLAY
CURRENT PLAYBACK POSITION
•
CHAPTER/TITLE REPEAT PLAY (DVD)
•
TRACK/DISC REPEAT PLAY (Video CD/CD)
For your reference
a. Repeat Play
■■
■■
■ DECK information screen (for DECK)
• Change the desired mode during play by pressing , and press
SET
.
• For repeat play in VCR mode, see p. 32.
b. Play mode [Video CD/ CD only] (See p. 39 or 40.)
Note
• Track No. and the elapsed playing time are not displayed during play started from menu of Video
CDs with playback control.
• When appears on the screen while a button is being operated, it means that the corresponding
operation is prohibited by DECK or the disc.
OFF Video CD menu play is cleared.
ON Video CD menu play is displayed.
Video CD CD
Note
4
SELECT :
SET : SET NEXT : D ISPLAY
TITLE : 1 DVD
CHAPTER : 12 1 : 12: 55
1
2
3
SET : SET NEXT : D ISPLAY
TRACKTRACK : 1 VIDEO CD
PBC : OFF 1 : 35 : 12
A
B
C
D
Video CD/CD TRACK REPEAT DISC REPEAT REPEAT OFF
DVD CHAPTER REPEAT TITLE REPEAT REPEAT OFF
PROGRAM PLAY program play
RANDOM PLAY random play
----
normal play
SELECT :
SET : SET END : DISPLAY
PLAY
CHAPTER REPEAT
a
SET : SET END : DI SPLAY
PLAY
DISC REPEAT
RANDOM PLAY
b
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1342
43
PLAY
PLAY MODE : NORMAL
00
:
00
:
00
MP3
MENU
ROOT
. .
VA
END
_
W
ALTZ
TECHNO
DD
_
CUB I C
POPS
N
O
CTURNE
J
AZZ
N
O
RN
DVD
Operation
1
Press
POWER
on the remote or DECK.
Press
OPEN/CLOSE
,
and then place a MP3 disc into the disc tray.
Press
OPEN/CLOSE
to close.
2
3
MP3 Playback
ROOT
VA
TECHNO
POPS
J
AZZ
END
_
W
ALTZ
DD_CUB I C
N
O
CTURNE
N
O
RN
<Example>
4
[PLAY MODE]
NORMAL:
All MP3 files are selected and
played back one time only.
SINGLE REPEAT:
The selected MP3 file is
played back repeatedly.
FOLDER REPEAT:
The MP3 files contained in
the selected folder are played
back repeatedly.
However, folders below the
selected folder are not played
back.
DISC REPEAT:
All MP3 files are played back
repeatedly.
■ Forward/Reverse Search
Press
FF/SLOW+
or
REW/SLOW-
during play.
Press
PLAY
to release.
• Search speed, slow at first, increases with each
additional press of the button up to 4 levels.
■ Forward/Reverse Track Skip
Press
SKIP
| or |
SKIP
during play.
Each press skips a track.
• If pressed within first 3 seconds of playback, skips
to the previous track. If over 3 seconds, returns to
first of that track. (|
SKIP
only.)
• Only the
SKIP
| or |
SKIP
button can be used
for track skip selection during playback.
Place unit into Stop mode before performing folder/
file selection (see above right.)
Function
Status
Counter
PLAY MODE
Folder area
File area
Press
STOP
to stop playing.
5
■ MP3 playback (During STOP mode)
1) Press
to select an MP3 file ( ).
2) Press
SET
or
PLAY
to start playback.
■ Select folder (During STOP mode)
1) Press
to select a folder ( ).
2) Press
SET
to display files/folders
contained in the folder.
■ Select parent folder (During STOP
mode)
1) Press
to select a folder ( ).
2) Press
SET
to make changes to
the previous directory display.
■ Select PLAY MODE (During STOP
mode)
1) Press
to move cursor to PLAY
MODE.
2) Press to select the desired
PLAY MODE (see below).
You can use this unit to play MP3 format audio recorded for
personal use with a computer etc. onto a CD-R or CD-RW.
Play may not be possible in some cases due to the
condition of the recording.
Parent
folder
Press
OPEN/CLOSE
to eject the disc.
The MP3 MENU is closed automatically.
MP3 Playback Operation
*Important: If a remote control button does not work
when pressed, press the DVD button on
the remote and try the button again.
(The currently
displayed folder
turns green)
(The selected
MP3 file/folder
is displayed
with a cursor.)
<Example>
• Folder area operation cannot be done.
Only file area operation is possible.
Note
: MP3 file
: Folder
: Parent folder
MP3 MENU is displayed and playback is
started automatically.
(The MP3 CD directory is
displayed.)
(The MP3 CD directory structure
displayed in the above example OSD
is shown in the diagram at left.)
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1343
44
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
1
DVD Lock (DVD only)
LEVEL 0 : LOCK ALL, Playback of all DVDs, CDs and
Video CDs is prohibited.
(Use to prohibit play of mature theme DVDs not
encoded with rating level.)
LEVEL 1 : mature theme DVDs
LEVEL 2 : DVDs expressly for children can be played back.
LEVEL 3 to 7 : DVDs for general audiences/children can be
played back. (DVDs with mature content
are prohibited.)
LEVEL 8 : NO LIMIT: (Factory preset)
All DVDs can be played back.
You can prevent playback of DVDs of a specific
rating level which may be unsuitable for children.
• Some DVDs are encoded with a rating level. If the disc
rating is higher (stricter) than the one you preset,
playback will be prohibited.
<When DVD Lock is activated>
After DVD Lock is set and a
blocked DVD is played, this
message will appear.
The message may differ
depending on the disc.
To continue viewing a blocked
program for now,
Press to select “YES” and
SET. Then, enter your 4 digit
secret code. When “NO” is
selected, blocked programs
cannot be viewed.
DVD Lock Feature
SELECT :
SET : SET END : D I SPLAY
,
YOUR SELECTION EXCEEDS THE
PLAYER S RATING LIMIT.
DO YOU WANT TO CHANGE THE
LIMIT?
YES
NO
Discs not encoded with rating
level will play even if the jacket
states it is for mature
audiences. For these discs, the
DVD Lock Ratings will not work.
Caution
4
Press
to select rating level, and
press
SET
to select “LOCKED” or
“UNLOCKED.”
5
Press
ACTION
twice
to end setup.
A 4-digit code must be entered to view a blocked
program or change rating settings.
Press
ACTION
*
to display MENU.
Press
to select “PARENTAL LOCK,”
and
press
SET
to display.
2
1) Press
NUMBER keys
to enter your secret code.
2) Enter same secret code
again for confirmation.
3) Press
SET
to display.
• Step 2) not necessary when
changing rating or secret
code.
• Take care that you are not
observed entering the
secret code.
To Make Corrections
Press repeatedly to
move the cursor.
Press
NUMBER keys
to
make the correction.
Change your secret code
• You will need your current code.
Do step 1 ~ 2 left.
Enter current secret code.
Press
CLEAR
to clear the code.
Do step 4 to enter new code.
• DO NOT forget your secret code.
Note
3
DVD MAIN MENU
SELECT :
SET : SET
END : ACTION
DISC LANGUAGES
AUDIO OUTPUT
ST I LL MODE : FIELD
TV MODE : Letterbox 4:3
PARENTAL LOCK : LEVEL 8
*Important: If a remote control button does not work when
pressed, press the DVD button on the remote
and try the button again.
Ready Checklist
DECK is in DVD mode, press DVD.
END
:
ACT
I
O
N
ENTER
:
0
-
9
ENTER 4
-
D
I
G
I
T
CODE
----
45
46
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
• Make settings according to amplifier
connected to optical audio output as shown
in above table.
• When a dts decoder is not connected, to
enjoy dts DVD, please select audio output
other than dts at the dts DVD menu screen.
Otherwise, there will be no sound.
*1 Audio Output 2 from DECK is converted to
48 kHz/16 bit in addition to audio from
digital audio output.
To enjoy high quality sound at 48 kHz/20
bit /24 bit or 96 kHz, connect the amplifier
or decoder directly to the Audio Output 2
connectors, not to the Digital Audio Output
connector. [Select “OFF” at the “LPCM
(DVD)”.]
*2 When connecting an amplifier (with an
optical digital input connector) which does
not contain the Dolby Digital or dts
decoder, be sure to select “OFF”.
If “Bitstream” is selected, starting DVD play
may cause such a high level of noise as to
be harmful to your ears and damage the
speakers.
*3 When a dts decoder is connected, please
select “Bitstream” in “dts”. If “OFF” is
selected, there will be no sound.
Audio Output
Select the digital output to be output from the optical
digital audio output connector of DECK.
■■
■■
■ “LPCM (DVD)” selections
OFF: Linear PCM of less than 48 kHz/16 bit is
output. When playing DVDs recorded in
linear PCM of over 48 kHz/20 bit or 96 kHz,
no digital audio is output. (Factory preset)
PCM: When playing DVDs recorded in linear PCM
of 48 kHz/20 bit/24 bit or 96 kHz, digital
audio converted to 48 kHz/16 bit is output.
(Digital output of PCM audio is restricted to
48 kHz/16 bit or below for copyright
protection.)
■■
■■
■ “Dolby Digital” selections
Bitstream: Dolby Digital bitstream (1ch-5.1ch) is
output. (Factory preset)
OFF: No output.
■■
■■
■ “dts” selections
Bitstream: dts bitstream is output. (Factory preset)
OFF: No output.
■■
■■
■
“DRC (Dynamic Range Compression)” selections
OFF: Normal audio range is selected. (Factory
preset)
ON: For dynamic sound even at low volume, this
is useful for late-night listening. [Dolby Digital
DVDs only].
■■
■■
■ “SURROUND” selections
Surround Sound creates the effect of sound coming
from non-existent rear speakers even when only
connected to a 2-channel stereo system.
OFF: No Surround Sound effect. (Factory preset)
ON: Surround Sound effect.
Press
to select an item,
and
press
SET
repeatedly for
output. (See below.)
Press
to select
“AUDIO OUTPUT,”
and
press
SET
to display screen.
1
Settings for DVD Operation (continued)
3
2
4
• Turn off other surround effects when using
this surround effect.
• For optimum effect, the distance between
DECK and the listener should be about 3 or 4
times the distance between the right and left
front speakers.
Notes
Recommended setting
LPCM
(DVD)
OFF
PCM*
1
PCM*
1
PCM*
1
Dolby
Digital
OFF
OFF*
2
Bitstream
Bitstream
dts
OFF
OFF*
2
OFF
Bitstream
No amplifier is connected
AV amplifier (with digital
audio input connector)
without Dolby Digital/dts
decoder
AV amplifier including
Dolby Digital decoder
AV amplifier including
Dolby Digital/dts decoder
*
3
Type of amplifier
to be connected
DVD MAIN MENU
SELECT :
SET : SET
END : ACTI ON
DISC LANGUAGES
AU
AU
DI
DI
O OUTPUT
O OUTPUT
ST I LL MODE : F
I
LED
TV MODE : L e tt e rb o x 4 :3
PARENTAL
LOCK
:
LEVEL 8
AUDIO OUTPUT
SELECT :
SET : SET
END : ACTION
LPCM(DVD)
LPCM(DVD)
: OFF
: OFF
Dolby Digital : Bitstream
d t s : OFF
DRC : OFF
SURROUND : OFF
Press
ACTION
to redisplay DVD menu
and go to step 2 to setup another item.
Or, press
ACTION
twice to exit.
Press
ACTION
*
to display MENU.
Ready Checklist
DECK is in DVD mode, press DVD.
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1346
47
48
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Language Code List
Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or
“MENUS” (see p. 45).
Code Language
7079 Faroese
7082 French
7089 Frisian
7165 Irish
7168 Scots Gaelic
7176 Galician
7178 Guarani
7185 Gujarati
7265 Hausa
7273 Hindi
7282 Croatian
7285 Hungarian
7289 Armenian
7365 Interlingua
7378 Indonesian
7383 Icelandic
7384 Italian
7387 Hebrew
7465 Japanese
7473 Yiddish
7487 Javanese
7565 Georgian
7575 Kazakh
7576 Greenlandic
7577 Cambodian
7578 Kannada
7579 Korean
7583 Kashmiri
7585 Kurdish
7589 Kirghiz
7665 Latin
Code Language
7678 Lingala
7679 Laothian
7684 Lithuanian
7686
Latvian, Lettish
7771 Malagasy
7773 Maori
7775 Macedonian
7776 Malayalam
7778 Mongolian
7779 Moldavian
7782 Marathi
7783 Malay
7784 Maltese
7789 Burmese
7865 Nauru
7869 Nepali
7876 Dutch
7879 Norwegian
7982 Oriya
8065 Panjabi
8076 Polish
8083
Pashto, Pushto
8084 Portuguese
8185 Quechua
8277
Rhaeto-Romance
8279 Romanian
8285 Russian
8365 Sanskrit
8368 Sindhi
8372
Serbo-Croatian
8373 Singhalese
Code Language
8375 Slovak
8376 Slovenian
8377 Samoan
8378 Shona
8379 Somali
8381 Albanian
8382 Serbian
8385 Sundanese
8386 Swedish
8387 Swahili
8465 Tamil
8469 Telugu
8471 Tajik
8472 Thai
8473 Tigrinya
8475 Turkmen
8476 Tagalog
8479 Tonga
8482 Turkish
8484 Tatar
8487 Twi
8575 Ukrainian
8582 Urdu
8590 Uzbek
8673 Vietnamese
8679 Volapük
8779 Wolof
8872 Xhosa
8979 Yoruba
9072 Chinese
9085 Zulu
Code Language
6565 Afar
6566 Abkhazian
6570 Afrikaans
6577 Ameharic
6582 Arabic
6583 Assamese
6588 Aymara
6590 Azerbaijani
6665 Bashkir
6669 Byelorussian
6671 Bulgarian
6672 Bihari
6678
Bengali; Bangla
6679 Tibetan
6682 Breton
6765 Catalan
6779 Corsican
6783 Czech
6789 Welsh
6865 Danish
6869 German
6890 Bhutani
6976 Greek
6978 English
6979 Esperanto
6983 Spanish
6984 Estonian
6985 Basque
7065 Persian
7073 Finnish
7074 Fiji
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1348
49
These displays will alert you to a missed operation or provide further instructions.
Warning and Instruction Displays
For Your
Information
PLEASE SET CLOCK BY
PRESSING ACTION KEY
CHECK CASSETTE
RECORD TAB
NO CASSETTE
VIDEO HEADS MAY NEED
CLEANING PLEASE INSERT
HEAD CLEANING CASSETTE
OR REFER TO MANUAL
END : PLAY
VCR LOCK ACTIVATED
Page
CautionOSD
If you attempt to set or review a Timer
Recording and the Clock is not set...
If DECK is not in Stop mode or a cassette
with record tab is not inserted 2 minutes
before a Timer Recording is about to
begin...
If you press REC on the remote control or
DECK, and a cassette is inserted with no
record tab...
If you press PLAY, FF, REW, or REC on
the remote control or DECK without a
cassette inserted...
If you press STOP or POWER
during a Timer Recording...
(visible in VCR mode only)
If head cleaning becomes necessary
while playing back a tape...
If you press a function button other than
STOP/EJECT or POWER while DECK is
in VCR Lock mode...
If you press an invalid key on the remote
while in CABLE/DSS mode...
If you press an invalid key on the remote
while in TV mode...
REMOTE CONTROL IS SET
TO TV MODE
USE VCR : VCR KEY
USE DVD : DVD KEY
REMOTE CONTROL IS SET
TO CABLE/DSS MODE
USE VCR : VCR KEY
USE DVD : DVD KEY
PLEASE PREPARE FOR TIMER
REC
PLEASE CHECK THE DISC,
AND FOR STAINS OR
SCRATCHES ON DISC
If you press PLAY, or DECK reads
data from a stained or scratched disc
in DVD mode. Also, if the type of disc
is other than DVD, Video CD or CD...
IT IS PROHIBITED TO COPY
DVD/VIDEO CD/CD TO VHS
If you press REC in DVD mode...
TO CANCEL TIMER REC
HOLD DOWN STOP KEY
FOR APPROX 3 SEC
24
24
25
6
20
21
25
6
33
28
29
34
4
21
28
29
34
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1349
50
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before Requesting Service
Power
No power…
Power turns itself off...
Recording & Playback
TV program cannot be recorded...
Timer recording cannot be
performed…
There is no playback picture, or the
playback picture is noisy or contains
streaks...
During Special effects playback,
picture may contain some vertical
jitter when using a TV with an
Automatic Vertical Hold Control...
DECK cannot be controlled...
Check the following points if you are having trouble with your DECK.
Correction
• Completely insert Power Plug into an AC outlet.
• Set POWER button to on.
• Make sure power source is active.
• Auto power-off (shutoff) occurs after about 5 min.
in DVD mode with no operation, or if there is no
broadcast signal in TV or Playback mode.
Turn the power back on. (pp. 23, 33)
Correction
• Check connections between DECK, external
antenna, and TV.
• Check channel selections.
• Make sure your antenna system (CABLE or TV) is
correctly set. (Channels [p. 18])
• Make sure cassette record tab is intact. (p. 6)
• Confirm that clock is set to current time and date.
• Make sure Cable/DSS box (if used) is left on and
tuned to channel to be recorded.
• Set recording start/stop times correctly. (p. 24)
• Timer recording may not be performed or continued
if a power interruption occurs before or during a
Timer Recording, even after power is restored.
• Select channel 3 or 4 on TV to match VCR output
channel (3 or 4) (p. 16) or select LINE.
• Set VCR/TV selector to “VCR.”
• Adjust TRACKING control in either direction. (p. 6)
• Try Head Cleaning. (p. 6)
• Set TV’s Vertical Hold Control to MANUAL, then
adjust.
• Make sure DECK power is on.
• Check Remote batteries.
• Make sure VCR LOCK is set to off. (p. 33)
• Make sure Remote is in proper mode.(p. 28)
• Make sure Timer Recording is not in progress.
Remote Control
DECK cannot be remote controlled...
PROG buttons do not respond...
Correction
• Make sure DECK power is on.
• Make sure Remote is in VCR mode.
• Aim Remote Control directly at remote sensor on DECK. (p.9)
• Avoid any object blocking signal path.
• Check Remote batteries. (p. 4)
• Exposing DECK remote sensor to direct fluorescent
or outdoor light may cause signal interference.
• PROG functions are not available in COMPONENT
Video Output and S-VIDEO OUT. Set TV to either RF
IN or VIDEO IN. (p. 10)
• Check Remote batteries. (p. 4)
• Press VCR or DVD button for DVD/VCR mode. (p. 28)
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1350
51
Check the following points if you are having trouble with your DECK.
Miscellaneous
Programs cannot be viewed on TV...
Video cassette cannot be inserted...
Video cassette ejects when
a recording is started or the power is
turned off for timer recording...
In Stop mode, the motor (CYLINDER)
continues to rotate...
The disc cannot be removed..
Correction
• Make sure TV is set to output of DECK.
• Check connections between DECK,
external antenna, and TV.
• Set VCR/TV selector to “TV.” (p. 21)
• Make sure proper signal source is selected.
• Insert the cassette with window side up; record
tab facing you.
• Make sure cassette record tab is intact. (p. 6)
• To enable Quick play mechanism, the cylinder will
rotate for about 3 minutes. This reduces response
time from Stop to Play mode.
• First, unplug DECK. Then, prepare a rigid wire
(e.g. an extended paper clip) and, applying
moderate force, insert it straight into the hole at the
base of the tray. The tray will eject a little. Now, pull
the tray all the way out and remove the disc. (p. 9)
DVD/ Video CD/ CD
Play fails to start even when PLAY is
pressed...
Play starts but then stops immediately...
Picture is distorted during rapid
advance or rapid reverse...
No Forward/Reverse Scene Search
play...
Play does not start even when title is
selected...
Audio soundtrack and/or subtitle
language is not the one selected at
the initial settings...
No subtitles...
Alternative audio soundtrack
(or subtitle) language cannot be
selected...
Angle cannot be changed...
Correction
• This DECK cannot play discs other than DVDs,
Video CDs and CDs.
• The disc may be dirty and require cleaning.
• Be sure disc is installed with label side up.
• The picture will be somewhat distorted at times:
this is normal.
• Some discs may have sections which prohibit
Forward/Reverse Scene Search. (p. 23)
• Confirm the “DVD LOCK” setting. (p. 44)
• If the audio soundtrack and/or subtitle language
selected at DVD initial settings does not exist
on the disc, it will not be accessible.
• Subtitles appear only when available on disc.
•“OFF” is selected at the changing subtitle
language. Select “ON” at the “Subtitle Languages”
section (p. 36) to display the subtitles.
• Alternative language cannot be selected with discs
which do not contain more than one language.
• For some discs, alternative language cannot be
selected with the AUDIO or SUB TITLE button.
Try selecting it from the DVD MENU if available.
• This function is dependent on software availability.
Even if disc has multiple angles, they may be
recorded for specific scenes only (ANGLE
indicator on DECK lights up). (p. 37)
If you cannot resolve the problem, please call the Customer Call Center for product
assistance at 1-800-211-PANA (7262).
To locate an authorized servicenter, please call toll free 1-800-211-PANA (7262).
or send e-mail to : [email protected]
For Your
Information
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1351
52
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Limited Warranty
PANASONIC CONSUMER ELECTRONICS COMPANY,
DIVISION OF MATSUSHITA ELECTRIC
CORPORATION OF AMERICA
One Panasonic Way Secaucus, New Jersey 07094
PANASONIC SALES COMPANY, DIVISION OF MATSUSHITA
ELECTRIC OF PUERTO RICO, INC.,
AVE. 65 de Infantería, Km. 9.5 San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Panasonic/Quasar Video Products
Limited Warranty
Limited Warranty Coverage
If your product does not work properly because of a defect in materials or workmanship, Panasonic
Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the warrantor”)
will, for the length of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it
with a new or a refurbished product. The decision to repair or replace will be made by the warrantor.
Product
Camcorder
DVD/VCR Deck,
A/V Mixer
TV/VCR, TV/DVD,
TV/DVD/VCR
Combination
TV/HDR
Combination
Rechargeable
Batteries
(in exchange for
defective item)
Tape
(in exchange for
defective item)
Memory Cards
(in exchange for
defective item)
Labor
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Ninety (90) Days
Not Applicable
Not Applicable
Not Applicable
Parts
One (1) Year (except
CCD Image Sensor)
CCD Image Sensor - 6
(Six) Months
One (1) Year
One (1) Year (except
CRT)
CRT - Two (2) Years
One (1) Year (except
CRT)
CRT - Two (2) Years
Ten (10) Days
Five (5) Days
Ninety (90) Days
Contact Number
1-800-211-PANA(7262)
1-800-211-PANA(7262)
1-800-211-PANA(7262)
1-888-843-9788
1-800-211-PANA(7262)
1-800-211-PANA(7262)
1-800-211-PANA(7262)
Service
Carry-In or Mail-In
Carry-In or Mail-In
Carry-In: 21” CRT
and Smaller
In-Home or Carry-In:
22” CRT and Larger
In-Home or Carry-In
Carry-In or Mail-In
Carry-In or Mail-In
Carry-In or Mail-In
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period,
there will be no charge for parts. You must carry-in or mail-in your product or arrange for in-home service,
as applicable, during the warranty period.
If non-rechargeable batteries are included, they are not warranted. This warranty only applies to products
purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original
purchaser of a new product which was not sold “as is”. A purchase receipt or other proof of the original
purchase date is required for warranty service.
Carry-In, Mail-in or In-Home Service
For Carry-In, Mail-In or In-Home Service (as applicable) in the United States call toll free contact number
listed above or visit Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or fax (787)-768-2910.
In-Home service, if applicable, requires clear, complete and easy access to the product by the authorized
servicer and does not include removal or re-installation of an installed product. It is possible that certain in-
home repairs will not be completed in-home, but will require that the product, or parts of the product, be
removed for shop diagnosis and/or repair and then returned.
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1352
53
Customer Services Directory
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your
nearest servicenter by visiting our Web Site.
For Product Information, Operating Assistance, Literature Request, Dealer Locations,
and all Customer Service inquiries please contact:
1-800-211-PANA (7262)
, Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST.
or send e-mail : [email protected]
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300 Fax (787)768-2910
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(Monday-Friday 6 am-5 pm; Saturday 6 am-10:30 am, PST)
(Visa, MasterCard, Discover Card, American Express, Check)
Accessory Purchases:
As of February 2002
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT
COVER normal wear and tear or cosmetic damage, nor does it cover markings or retained images on
the picture tube resulting from viewing fixed images (including, among other things, letterbox pictures
on standard 4:3 screen TV’s, or non-expanded standard 4:3 pictures on wide screen TV’s, or
onscreen data in a stationary and fixed location). The warranty ALSO DOES NOT COVER damages
which occurred in shipment, or failures which are caused by products not supplied by the warrantor,
or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication,
alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, or commercial use (such as in a hotel,
office, restaurant, or other business), rental use of the product, service by anyone other than a
Factory Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY
COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having
someone remove or re-install an installed unit if applicable, or travel to and from the servicer, loss of
media or images, data or other memory or recorded content. The items listed are not exclusive, but
are for illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state. If a problem with this product develops during or after the warranty period, you may
contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then write to the
warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.
PARTS AND SERVICE (INCLUDING COST OF AN IN-HOME SERVICE CALL, WHERE
APPLICABLE) WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY ARE YOUR
RESPONSIBILITY.
For Your
Information
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1353
54
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Spanish Quick Use Guide/ Guía para rápida consulta
Para ajustar el idioma, canal yPara ajustar el idioma, canal y
Conexiones/Configuracion Inicial (READY TO PLAY)
Favor realice la conexion de antena o cable antes de conectar el cordon de AC a la
toma de pared.
Conectando el cordon de AC de la DECK en toma de pared iniciara automaticamente la busqueda
de canales y colocacion de tiempo.
Conectando
Conecte Ant/Cable a la entrada de antena
de la DECK (DECK In)
Conecte la salida de la DECK (DECK Out) a
la entrada de antena de la TV (TV In) con el
cable-accesorio RF incluido.
Para Ant/Cable-DECK-TV
Para Sistema Digital de Satelite (DSS)/ Convertidor de cable-DECK-TV
Conecte la salida del convertidor de cable
a la ”DECK In” con el RF cable accesorio
incluido.
Conecte “DECK Out” a la “TV In” con el
cable-accesorio incluido.
2
1
2
1
Realizando configuracion inicial
Presione el boton DECK del control remoto
para dicha modalidad. Encienda la TV y
cambie a canal 3.
Conecte cordon de AC de la DECK a la
toma de pared. La DECK se activara e
iniciara busqueda de canales y colocacion
de tiempo.
• Si la pantalla abajo no aparece cheque la
conexion DECK-TV y si la TV fue cambiada a
el canal 3,trate cambiando a el canal 4.
• Para cambios a el canal de salida de la DECK
favor hacer referencia a “VCR’s Output
Channel” (p. 19).
Conectando cordon de AC a la toma de pared.
1
2
DECK
VHF/UHF
Estuche convertidor
de TV por cable
Televisor
Terminal
IN FROM ANT.
Entrada (IN) desde
ANT./CABLE
Terminal
OUT TO TV
Terminal IN FROM ANT.
Televisor
DECK
VHF/UHF
Terminal
OUT TO TV
Entrada (IN) desde
ANT./CABLE
2
1
Si usa convertidor de cable solo enciendala y
seleccione el canal PBS en su horario de uso u
horario de zona. Si utiliza receptor DSS este debe
estar apagado.
PRECAUCION
Si se sobre ajusta “NUT TYPE” el cable coaxial
RF podria dañar las terminales de conexion.
Ajusta ligeramente utiliza solo los dedos.
Selecciones se realizaron automaticamente
cuando la configuracion termino, esta
pantalla aparece.
Si “AUTO CLOCK SET IS INCOMPLETE”
aparece, coloque manualmente el tiempo, vealo
abajo.
3
Realizando configuracion inicial
Si la colocacion de tiempo fue incompleta.
Presione la tecla ACTION en el control remoto
para visualizar la pantalla del menú RELOJ.
1
Presione para seleccionar el mes y SET
para ajustar. De la misma forma, seleccione y
ajuste la fecha, año, hora y DST (Hora de
Verano).
2
1
2
3
Presione dos veces la tecla ACTION para
poner el RELOJ en marcha y salir.
VERANO
:
ACT
ELEGIR
:
FIJAR
:
SET
SALIR
:
ACT
I
O
N
FIJAR RELOJ
1
/
--
/
----
--
:
--
ELEGIR MES
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
VERANO
:
ACT
FIJAR RELOJ
9
/
29 /
2002
DOM
12:00PM
FIJACION ES COMPLETO
-
-
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]
Al inicio, el idioma de
la pantalla está fijado
a inglés.
Para cambiar el
idioma consulte la
página 18.
9
/
29
/
20
02
SUN
2
:
20P
M
D
S
T
:
ON
SETT
I
N
G
: CH
10
AUTO CLOCK SET
C
O
M
PLETED
AUTO CLOCK SET IS
I
NC
O
M
PLETE
PLEASE SET CLOCK BY
PRESSING
ACT
I
ON KEY
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
CH AUTO SET PROCEEDING
CANCEL : STOP
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1454
55
Operaciones básicas para la reproducción
1
2
3
Inserte un cassette,
• La alimentación del DECK se activa.
En la Pantalla de Visualización Multi
Función se ilumina “VCR”.
Presione PLAY para reproducir el cassette.
• Si el cassette no tiene lengüeta de
prevención de grabación (página 6), se
inicia la reproducción automáticamente.
Detalles especiales durante la grabación
Presione FF/SLOW+ o REW/SLOW- para
búsqueda de escenas hacia delante/ hacia
atrás. Presione PLAY para liberar. Luego de
que la búsqueda se ha iniciado, cada vez
que presione FF/SLOW+ o REW/SLOW-
se cambia la velocidad como sigue:
[SLP] aprox. 21X
↔↔
↔↔
↔ aprox. 9X
[LP] aprox. 9X
↔↔
↔↔
↔ aprox. 7X
[SP] aprox. 7X
↔↔
↔↔
↔ aprox. 3X
Si la imágen se interrumpe con la velocidad de
21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x.
Presione PAUSE/STILL para imagen Fija
(Congelada).
Presione PLAY para liberar.
Presione PAUSE/STILL en el modo de
imagen fija para imágenes cuadro a cuadro.
Presione PLAY para liberar.
Presione FF/SLOW+ o REW/SLOW- en el
modo de imagen fija para imágenes cuadro
a cuadro. Presione PLAY para liberar.
Presione STOP para detener el cassette.
Presione REW/SLOW- o FF/SLOW+ en el
modo de parada para rebobinado/avance
rápido del cassette.
Presione EJECT en el control remoto,
o STOP/EJECT en el DECK para expulsar
el cassette.
Operaciones básicas para la grabación
1
Inserte el cassette con lengüeta de
protección de grabación (pág. 6).
Presione CH / , o las teclas de números
para seleccionar el canal.
Presione SPEED para seleccionar la
velocidad de grabación (pág.6)
Presione REC para comenzar a grabar.
• Para eliminar escenas indeseadas, presione
PAUSE/STILL para pausar, y al presionar
nuevamente se reanuda la grabación.
• No podrá ver otro canal durante la
grabación.
Presione STOP para detener la grabación.
• SP = Reproducción estándar,
• LP = Larga duración,
• SLP = Superlarga duración.
2
3
4
5
Grabación de un toque (grabar en
marcha),
Presione REC repetidamente para ajustar la
hora de grabación (30 min - 4 horas).
• La videograbadora termina la grabación
a una hora programada.
Grabación normal
0:30 1:00
1:302:003:004:00
Programación fácil para la
grabación con temporizador
1
2
3
Presione PROG
para visualizar PROGRAM.
1) Para ajustar la FECHA de
grabación, presione
para seleccionar:
1-31 = una vez, o
DIARIO = a la misma hora
de lunes a viernes, o
SEMANA = a la misma
hora cada semana y
presione SET para ajustar.
2) Para ajustar los ítems que quedan,
presione para seleccionar y presione
SET para ajustar los tiempos de INICIO/
PARADA, CANAL, o entrada de LÍNEA (pág.
35), y velocidad del cassette (SP, LP, SLP).
Presione PROG para finalizar PROGRAM.
Presione
para seleccionar un número
que no está usando para
ingresar mas programas y
presione SET
para ajustar.
Luego repita el paso 2.
O
Presione nuevamente
PROG para salir.
Fecha de hoy
Orden para elegir
Ejemplo
FECHA
I
N
I
C
I
O
PARADA
C
A
7
SAB
--:--
--:--
--
HOY
ELEGIR
:
FIJAR
:
SET
TERMINAR
:
PROG
SLP
ELEGIR FECHA DE I
N
I
C
I
O
DIARIO
7
2
1
31
68 9
/ Orden para elegir
SEMANAL
(
SAB
)
SEMANAL
(
LUN
)
SEMANAL
(
DOM
)
C
AN
C
ELAR
:
A
DD
/
DLT
ELEGIR 1- 8 :
ENTRAR
: SET
SAL
I
R
:
PROG
FE
I
N
I
C
PARADA
CA
VEL
7
2 : 00
P
3
:
20
P
02 SLP
--
--
:
--
--
:
--
--
--
--
--
:
--
--
:
--
--
--
--
--
:
--
--
:
--
--
--
Guía para rápida
consulta
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1455
56
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Spanish Quick Use Guide/ Guía para rápida consulta
1
Presione
POWER
en el control remoto o el aparato.
Presione
DVD
para seleccionar el modo DVD.
1) Presione
OPEN/CLOSE
.
2) Ponga un disco en la bandeja de disco.
• Sujete el disco sin tocar ninguna de sus superficies,
póngalo con el lado donde esté impreso el título
hacia arriba, alinéelo con las guías y póngalo en su
posición apropiada.
Disco de 3”(8 cm) Disco de 5” (12 cm)
Presione
PLAY
para iniciar la reproducción.
La bandeja del disco se cierra automáticamente.
• Si está usando un DVD interactivo (Interactive DVD)
o un Vídeo CD con contol de reproducción
(playback control) y aparece un menú de títulos
(TITLE MENU) en la pantalla, siga al paso 5.
Presione o las teclas numéricas para
seleccionar el artículo deseado.
Presione
SET
para la reproducción.
Si usa las teclas numéricas, la reproducción
comienza automáticamente.
Presione
STOP
para parar la reproducción.
Presione
OPEN/CLOSE
para expulsar el disco.
■ Para buscar una escena particular
Búsqueda hacia adelante
Presione
FF/SLOW+
en el modo de reproducción.
Búsqueda hacia atrás
Presione
REW/SLOW-
en el modo de reproducción.
(Para liberar, presione
PLAY
)
■ Para saltar un capítulo o una pista
Salto hacia adelante
Presione
SKIP
l en el modo de reproducción.
Un capítulo (DVD) o una pista (Vídeo CD/CD) se salta cada ves que se oprime la tecla.
Salto hacia atrás
Presione l
SKIP
en el modo de reproducción.
■■
■■
■ Para ver una imagen fija
Presione
PAUSE/STILL
durante la reproducción.
(Para liberar, presione
PLAY
)
■ Para ver imágenes cuadro a cuadro
(DVD/Vídeo CD)
Presione
PAUSE/STILL
en el modo de imagen fija.
La imagen avanza un cuadro cada vez que presiona la tecla.
(Para volver a la reproducción normal, presione
PLAY
.)
■ Para ver en cámara lenta (DVD/Vídeo CD)
Presione
FF/SLOW+
o
REW/SLOW-
en el modo de imagen fija.
(Para liberar, presione
PLAY
)
3
4
5
6
Operaciones básicas del DVD
7
2
OPEN/
CLOSE
SET
STOP
POWER
REW/
SLOW-
NUMBER
keys
PLAY
DVD
PAUSE/
STILL
SKIP
SKIP
SELECT
FF/
SLOW+
Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1456
57
1
Cuando se presiona DISPLAY, la visualización en pantalla
muestra la información del disco (título / capítulo / número de
lista, tiempo transcurrido de reproducción, audio / idioma del
subtítulo, y ángulo) e información (repetir la reproducción,
modo reproducción, Karaoke vocal encendido / apagado, etc.).
Funcionnamiento del DVD utilizando
visualizaciones en pantalla
Presione
DISPLAY
en el modo reproducción o parada
para visualizar Visualizaciones en pantalla.
• Cada vez que se presione
DISPLAY
, la visualización
en pantalla cambia como se muestra a continuación.
2
3
Presione para seleccionar el ajuste deseado.
Presione
SET
para ajustar.
Para volver a la pantalla normal,
Presione repetidamente
CLEAR
o
DISPLAY
.
Presione (o ) para seleccionar el ítem deseado.
Presione
SET
para ajustar.
ELEGIR :
FIJAR : SET SIGUIENTE: DISPLAY
T I TULO : 12 DVD
CAPITULO
: 11 0:12:34
ELEGIR :
FIJAR : SET SIGUIENTE: DISPLAY
T I TULO : 12 DVD
CA
CA
PI
PI
TULO
TULO
: 24
24
0:12:34
PI
PI
STA
STA
: 12
12
VIDEO CD
PBC : INACTIVO 0 : 12 : 34
FIJAR : SET SIGUIENTE: DISPLAY
PI
PI
STA
STA
: 17
17
VIDEO CD
PBC : INACTIVO 0 : 12 : 34
FIJAR : SET SIGUIENTE: DISPLAY
Información seleccionada del disco
Información seleccionada de del DECK
Pantalla normal
SELECT
DISPLAY
CLEAR
SET
Guía para rápida
consulta
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1457
58
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
1
Cambio del idioma de subtítulos
[DVD solamente]
EI idioma de los subtítulos seleccionado al hacer las
fijaciones iniciales se puede cambiar por otro idioma
diferente, si éste se encuentra disponible.
Presione
SUBTITLE
durante la reproducción.
Cuando no haya
subtítulos grabados, “-”
se visualizará en lugar
del número de idioma.
Presione para
seleccionar el idioma
deseado.
Presione (o ) para
ajustar.
Presione para
seleccionar “ACTIVO” o
“INACTIVO.”
1
Cambio del idioma de la pista de
sonido [DVD solamente]
EI idioma de la pista de sonido seleccionado al hacer
las fijaciones iniciales se puede cambiar por otro
idioma diferente, si éste se encuentra disponible.
Presione
AUDIO
durante
la reproducción para
visualizar la pantalla
AUDIO.
2
Presione para
seleccionar idioma.
Selección de IDIOMAS DEL
DISCO [DVD solamente]
Presione para seleccionar el artículo deseado.
Presione
SET
.
4
1
2
3
IDIOMAS DEL DISCO
Todos los idiomas ofrecidos en el disco pueden ser
ajustados, Si el idioma ajustado no es ofrecido en el
disco, se seleccionará el idioma original del disco.
SALIDA DE AUDIO
Puede usted ajustar la salida audio procedente del
terminal de salida audio digital.
DETENER RASTREO
Para seleccionar “CAMPO” o “CUADRO fijo” para
prevenir inestabilidad o para permitir ver textos
pequeños o patrones finos claramente en el modo
de imagen fija.
PREFERENCIA
Para seleccionar si el material del vídeo para
pantalla ancha será vuelto a reproducir en el estilo
Pan&Scan, en el estilo Letterbox o en el estilo 16 :
9 en la pantalla.
5
Volver a visualizar el menú de DVD para
continuar el ajuste.
Presione
ACTION
y pase al paso 3 para ajustar
otro ajuste o, para salir, presione
ACTION
tres
veces.
Presione DVD para seleccionar el mode DVD.
Presione ACTION en el modo de parada para
visualizar MENU.
Presione para seleccionar el artículo deseado.
Presione
SET
.
Seleccione “AUDIO”
(Fijación de fábrica : inglés)
Inglés / Español / Francés / Japonesa :
Originl : Se seleccionará el idioma
original de cada disco.
OTRO **** : Se puede seleccionar el otro
idioma.
Seleccione “SUBTITULO”
(Fijación de fábrica)
AUTO : Se seleccionará el mismo que fue
seleccionado en la preparación
de “AUDIO”.
• Si el idioma seleccionado en la
preparación de “AUDIO” se utiliza
durante la reproducción, los subtítulos
no aparecerán.
• Si se utiliza otro idioma durante la
reproducción, los subtítulos aparecerán
en el idioma seleccionado en la
preparación de “AUDIO”
Inglés / Español / Francés / Japonesa :
OTRO **** : Se puede seleccionar el otro
idioma.
Seleccione “MENU”
(Fijación de fábrica : inglés)
Inglés / Español / Francés / Japonesa :
OTRO **** : Se puede seleccionar el otro
idioma.
Fijaciones iniciales
Spanish Quick Use Guide/ Guía para rápida consulta
Por ayuda llame al 1-800-211-PANA(7262) o envie e-mail a : [email protected]
2
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1458
59
Algunos discos con películas, por ejemplo,
vienen con dos o más títulos. Si el disco tiene
un menú de títulos grabados, el botón TITLE
podrá utilizarse para seleccionar el título de la
película.
Presione
TITLE
durante la reproducción.
Ahora se visualiza una lista de los títulos
del disco.
Utilización de un menú de títulos
[DVD solamente]
T
I
TLE MENU
Cas
t
l
es
Love
r
s
Dogs
B
i
r
ds
Presione o
las teclas de
números para
seleccionar el título
deseado.
Presione
SET
.
1
Algunos discos DVD tienen estructuras únicas de
menús llamadas menús DVD. Por ejemplo, los DVDs
programados con un contenido complejo
proporcionan menús guía, y los grabados con varios
idiomas proporcionan menús para audio e idiomas de
subtítulos. Aunque los contenidos de los menús DVD
y la operación cambian de disco a disco, a
continuación se explica la operación básica cuando
se utiliza esta característica.
Presione
MENU
durante la reproducción.
El menú de DVD introducido en el disco se
visualiza ahora.
Dogs
of the world
1
Visión desde otro ángulo
[DVD solamente]
Algunos discos DVD tienen escenas que han
sido filmadas simultáneamente desde un
número de ángulos diferentes. Con estos
discos, la misma escena podrá verse desde
cada uno de estos ángulos diferentes
utilizando el botón ANGLE.
Presione
ANGLE
durante la
reproducción para
visualizar la
pantalla de ángulo.
ANGULO
ANGULO
: 1
ELEGIR : F I JAR : SET
2
ANGULO
ANGULO
: 2
ELEGIR : FIJAR : SET
Presione
AUDIO
durante la reproducción
para visualizar la pantalla AUDIO.
Selección de vocal para los discos de
Karaoke [DVD/Video CD]
Presione (o )
para seleccionar el ajuste
deseado.
Presione (o ) para
ajustar. (DVD solamente)
Printed in Indonesia
LSQT0618B
S0302-1052
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Index
A ACTION button ..............................................8, 18
Accessories ......................................................... 4
ADD/DELETE button (Add or Delete a Channel) .8, 19
Audio Broadcast types (Stereo/SAP/Mono) .... 26
Audio Mode (Playback, Recording) ................. 27
Auto Operation Functions ............................... 31
Auto Shut-Off .................................................... 33
B Batteries .............................................................. 4
C Channel (“SET UP CHANNEL”) ....................... 18
Channel Up/Down, Tracking/V-Lock Button ... 6, 8
Clock (“SET CLOCK”) ....................................... 18
Commercial Skip ............................................... 31
Connections ............................................. 12 ~ 15
Copy Your Tapes (Dubbing) ............................ 35
COUNTER RESET button ............................8, 32
Customer Services Directory ............................ 53
D DISPLAY button ........................................... 8, 11
DSS/CABLE mode button ........................... 8, 28
DST (Daylight Saving Time) ............................. 19
E EJECT button ...............................................8, 20
ENTER button (For tuning TV Channel) .....8, 28
F FAST FORWARD/SEARCH button ............. 8, 20
H Head Cleaning .................................................... 6
I Index Search .................................................... 30
Indicator (Multi Function Display) .................... 11
Initial Setup (Ready to Play) ..................... 16, 17
INPUT button ................................................8, 35
L Limited Warranty ....................................... 52, 53
Location of Controls (Remote, DECK) ..... 8 ~ 10
M Multi-Brand Control .................................... 28, 29
O On-Screen Displays (VCR) ................................ 11
One Touch Recording ...................................... 21
DECK & VCR
P PAUSE/STILL button (Still Picture) .............8, 20
PLAY button (Playback a Tape) .................8, 20
POWER button ................................................... 8
PROG button (PROGRAM) .......................... 8, 24
Program Clear, Review, Replace ..................... 25
Program End Search ........................................ 30
Q Quality Picture ..................................................... 6
R REC button (Record on a Tape) .................8, 21
Record Tab ......................................................... 6
Remote Sensor ................................................... 9
Remote Warning ............................................... 34
Repeat Play ...................................................... 32
REWIND/SEARCH button ............................8, 20
S SAP/Hi-Fi ........................................................... 27
SEARCH (Index and Program End Search) ... 30
Servicenter List ................................................. 52
SLOW+/SLOW
-
button (Slow Motion Picture) .. 8, 20
Spanish Quick Use Guide ....................... 54 ~ 59
Specifications ...................................................... 7
SPEED button .............................................. 8, 21
Still (Freeze) Picture ......................................... 20
STOP button .................................................8, 20
T Tape Position, Tape Status ............................. 34
Timer Recording ............................................... 24
Trouble Shooting ....................................... 50, 51
TV mode button ............................................ 8, 28
V VCR Lock .......................................................... 33
VCR mode button.........................................8, 28
VCR/TV button......................................... 8, 9, 21
VOLUME +/
-
button (TV Volume) ............... 8, 28
W Warning and Instruction Displays .................... 49
Weak Signal Display ......................................... 33
Z ZERO SEARCH button ................................8, 32
A ACTION button .............................................8, 45
ANGLE button (Multiple Angle Viewing) ..... 8, 37
AUDIO CONTROL button ............................8, 40
AUDIO button (Audio Soundtrack Language) ..8, 36
Audio Output (For Selecting Audio Output) ... 46
Auto Power Off Function .................................. 23
C CLEAR button ........................................ 8, 39, 44
Component Video Output ......................... 10, 13
D Disc Languages ................................................ 45
DISPLAY button (“On-Screen Display”) ...... 8, 41
DVD Menu ......................................................... 38
DVD mode button.........................................8, 28
DVD Lock Ratings ............................................ 44
F Frame by Frame Picture ................................... 23
Forwards/Reverse Chapter/Track .................... 23
Forwards/Reverse Scene Search.................... 23
K Karaoke (Vocal Selection for Karaoke Discs) .... 37
L Language Code List ........................................ 48
M MENU button (To display DVD Menu) ........8, 38
MP3 ................................................................... 43
Multiple Angle Viewing ..................................... 37
O OPEN/CLOSE button................................... 8, 22
Optical Digital Audio Output ..................... 10, 15
P PLAY button (Play a Disc) ........................... 8, 22
Program Play (For Video CD/ CD) ................... 39
R Random Play (For Video CD/ CD) ................... 40
Repeat Play ...................................................... 42
Resume Function ............................................. 23
RETURN button ............................................8, 22
S SEARCH button
(Forward/Reverse Scene Search) .............8, 23
SKIP l or l button
(Forward/Reverse Chapter/Track) .............8, 23
SLOW+/SLOW
-
button (Slow Motion Picture) .8, 23
Sound Output Level .........................................40
STILL button (Still Picture or Pause) .......... 8, 23
Still Mode (For selecting “FIELD” or “FRAME”) ... 47
STOP button .................................................8, 22
SUBTITLE button
(For selecting Subtitle Language) .............8, 36
SURROUND button ...................................... 8, 23
S-Video Out ............................................... 10, 13
T TITLE button (Title Menu) ............................8, 38
TV Mode (For selecting the screen display style) .... 47
V Video CD ........................................................... 23
Z ZOOM button (Picture Zoom) ...................... 8, 37
DVD
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
P
PV-D4732S P36-60 (2nd) [LSQT0618B].p65 2002/05/23, 18:1460
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
Panasonic DVD VCR Combo PV-D4732S Manual de usuario
- Categoría
- Reproductores de DVD
- Tipo
- Manual de usuario
en otros idiomas
Artículos relacionados
-
Panasonic MP3 Player PV-D4762 Manual de usuario
-
-
-
-
-
-
-
-
-
Otros documentos
-
Quasar OmniVision VHQ-40M Manual de usuario
-
Magnavox MDV560VR Manual de usuario
-
-
Toshiba SD-V392SU Manual de usuario
-
Yamaha KX-W482 Manual de usuario
-
Disney W1320PTVD Manual de usuario
-
-
-