My O Time: Press “my o time” button and the

clock will begin flashing. Select desired o time

and press Set ( ). (Default is 10PM for all days.)

Days of the week will then flash on screen. Use

arrows ( ) to select the day(s) you want the

timer to be active and press Set ( ).

Sunset On: Press “sunset on” button and the

sunset time will flash on the screen. Use arrows

( ) to adjust time (time can be adjusted up

( ) to adjust time (time can be adjusted up

to 1 hour in either direction) and press Set ( ).

Days of the week will then flash on screen. Use

arrows ( ) to select the day(s) you want the

timer to be active and press Set ( ).

Extra programs: This option oers 7 additional

On/O programs. When the “my extra programs”

button is pressed “ON 1” will flash on screen but

no time will be displayed, only “--:--.” Press Set

( ) to select program “ON 1” and the “--:--” will

Program O 1 (“OFF 1”), Program On 2 (“ON 2”), Program O 2 (“OFF 2”), etc.

To skip through without setting, simply stop pressing buttons and the display

will revert to clock mode after 10 seconds. You can also use the arrows ( ) to

scroll through the options without setting a time. After Program O 7 (“OFF 7”),

the menu will start over with Program On 1 (“ON 1”). The LED indicator light will

remain on if any of the additional programs are set.

To delete one of the extra programs: Use arrows ( ) to choose the program

you wish to delete and press ( ) to select program. Use arrows ( ) to

scroll time back to between 11:59pm and 12:00am. The display will show “--:--”

to confirm the program has been deleted. No additional steps are needed. The

will now count down for the time set every time

the on/o or door override is used. While timer is in

countdown mode, the timer will run the programs

normally but will use the countdown time every

time the on/o override is selected.

4. Reset Button

To set the timer back to factory settings, press the

reset button (

r

) with a toothpick. The reset button

can be found behind the door in between the “my

current time. Take note of the AM/PM setting.

Note: When timer is reset, the time will flash.

2. Settings

Hold Set ( ) for 3 seconds and current time will

flash on the screen. Use ( ) to select current

time and press Set ( ).

“YEAR” will flash on the screen. Use ( ) to

select the current year and press Set ( ).

“MONT” will flash on the screen. Use ( ) to

select the current month and press Set ( ).

“ON” if you would like the timer to automatically adjust for Daylight Savings

Time or “OFF” if you would not like the timer to adjust automatically.

Note: If no button is pushed for 10 seconds, the timer will go back to clock

mode. To re-enter settings, press and hold Set ( ) for 3 seconds. Use the

( ) to scroll to the setting you were at.

Once settings are complete, either wait 10 seconds and the timer will

automatically go to clock mode, or press and hold “Set” ( ) for 3 seconds.

3. Programming Options (Preset)

Note: If the LED on a button is illuminated, this indicates that the program is

active. To deactivate program, press the button again and the LED will turn o.

correct day options and press set ( ).

My On Time: Press “my on time” button and

the clock will begin flashing. Use arrows to set

the desired on time ( ) and press Set ( ).

(Default is 6PM for all days.) Days of the week

will then flash on screen. Use arrows ( ) to

select the day(s) you want the timer to be active

and press Set ( ).

MADE IN CHINA

Distributed by Jasco Products Company LLC, 10 E.

RISK OF ELECTRIC SHOCK

• SHUT OFF POWER AT FUSE BOX OR CIRCUIT

BREAKER BEFORE INSTALLATION

• DO NOT USE IN WET LOCATIONS

• USE INDOORS ONLY

RISK OF FIRE

• DO NOT USE TO CONTROL APPLIANCES

THAT CONTAIN HEATING ELEMENTS

(COOKING APPLIANCES, HEATERS,

Specifications:

120VAC 60Hz

15A (1800W) General Purpose/Resistive

10A (1200W) Tungsten

1200 VA Ballast

5A Electronic Ballast

1/2 HP Motor

Works with dimmable

LED and CFL bulbs.

This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is

subject to the following two conditions: (1 this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

r

Declaración de la Comisión Federal de Comunicaciones (FCC)

Este dispositivo cumple con las especificaciones del apartado15

de las normas de laFCC y con las especificaciones de las normas

radioeléctricas (RSS) del Ministerio de Industria de Canadá aplicables a aparatos exentos de licencia. El

funcionamiento está sujeto a las siguientes dos condiciones: (1) este dispositivo no debe provocar interferencia

perjudicial, y (2) este dispositivo debe aceptar toda interferencia que reciba, incluso la que pudiera causar un

funcionamiento no deseado.

NOTA DE LAFCC: El fabricante no se hace responsable de ninguna interferencia de radio oTV ocasionada por

modificaciones no autorizadas efectuadas a este aparato. Dichas modificaciones podrían anular la autoridad del

usuario para utilizar este aparato.

que puede determinarse encendiendo y apagando el equipo, se recomienda que el usuario intente corregir la

interferencia por medio de la implementación de una o más de las siguientes medidas:

• Reorientar o reubicar la antena receptora.

• Incrementar la separación entre el equipo y el receptor.

• Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que el receptor está conectado.

• Consultar al distribuidor o a un técnico con experiencia en radio/televisión para solicitar asistencia.

CAN ICES-3(B)/NMB-3(B)

NORTE

CENTRAL

SUR