PPA Contatto Wi-Fi Module Manual de usuario

Marca: PPA

Modelo: Contatto Wi-Fi Module

Tipo: Manual de usuario

WARNING: This equipment is not entitled to protection

again harmful interference and may not cause interference to

duly authorized syems.

1. TECHNICAL FEATURES

• Equipment used to turn alarm syems, electric fence energizers

or automatic gate openers able to communicate to a cell phone

via Wi-Fi, making them more sophiicated and compatible with

apps for Android and iOS cell phones

• Sends atus notications of your control panel on your cell

phone via app (Android / iOS)

• Control your alarm syem, automatic gate operator or electric

fence energizer from wherever you are via app

• Setup via App

• 1 relay output

• Works with Wi-Fi technology

• Compatible with mo alarm syems, automatic gate operators

and electric fence energizers.

2. CONNECTIONS

1 – MAIN CON-

NECTOR: To con-

nect the wires of

the main con-

nector according

to the product in

which the Con-

tatto Wi-Fi will be

inalled, refer to

item 2.1.

2 – ‘LD1’ LED:

Flashing: Not con-

nected to the In-

ternet.

Lit: Connected to

the Internet.

3 – ‘SW1’ BUTTON: When pushed, it resets Contatto Wi-Fi settings

back to the factory settings.

4 – AUXILIARY RELAY: To connect the wires of the main connec-

tor according to the product in which the Contatto Wi-Fi will be

inalled, refer to item 2.1.

5 – WI-FI MODULE

6 – APPLICATION SETTING JUMPER (‘JP1’ JUMPER):

Selects Contatto Wi-Fi application. To select the model, ju close

the jumper accordingly and leave the other jumpers open.

• ‘Portão’ (Gate) Position: Contatto Wi-Fi is

being inalled in a gate operator con-

trol board.

• ‘Alarme’ (Alarm Syem) Position: Wi-Fi

contact is being inalled in an alarm

syem (panel).

• ‘Cerca’ (Electric Fence) Position: Con-

tatto Wi-Fi is being inalled in an elec-

tric fence energizer.

Below are the tables for connecting the

Contatto Wi-Fi wires for each application of the

product, Gate operator, Electric Fence energizer and Alarm syem.

NOTE: PRECAUTIONS BEFORE INSTALLING THE

WI-FI NETWORK - Contatto Wi-Fi has a relative consumption

of 120mA. In case there is an extra accessory connected to the

control panel, we recommend using a top-quality external 12Vdc

and 1Ah power supply.

2.1 ‘GATE’ MODE

WIRE COLOR FUNCTION

Red 12V

Black GND (the same as the gate operator’s control

board)

Orange GND Signal for 0.5 second to activate the

pushbutton on the gate operator’s control board

White

Input port connected to the Operator limit switch

‘GND’: Closed gate

‘+’: Open gate

Blue No use

Gray Normally closed (NC) of the auxiliary relay

Yellow Common (CM) of the auxiliary relay

Green Normally open (NO) of the auxiliary relay

2.2 ‘ELECTRIC FENCE’ MODE

WIRE COLOR FUNCTION

Red 12V

Black GND (the same as the electric fence energizer)

Orange No use

White

Input port connected to the output port of the

electric fence energizer which acknowledges the

‘armed’ and ‘disarmed’ atuses. (Connect a 1k

resior to the GND).

‘GND’: Disarmed

‘+’: Armed

Blue

Input port connected to the siren positive, res-

ponsible for acknowledging when the fence

has been triggered (Connect a 1k resior to the

GND).

Gray Normally closed (NC) of the auxiliary relay

Yellow

Common (CM) of the auxiliary relay, it mu be

connected to several terminals of the activation

switch

Green

Normally open (NO) of the auxiliary relay, it mu

be connected to one of the terminals of the ac-

tivation switch

2.3 ‘ALARM SYSTEM’ MODE

WIRE COLOR FUNCTION

Red 12V

Black GND (the same as the alarm syem)

Orange No use

White

Input port connected to the output port of the

alarm syem which acknowledges the ‘armed’

and ‘disarmed’ atuses. (Connect a 1k resior to

the GND).

‘GND’: Disarmed

‘+’: Armed

Blue

Input port connected to the siren positive, res-

ponsible for acknowledging when the alarm sys-

tem has been triggered (Connect a 1k resior

to the GND).

Gray

Normally closed (NC) of the auxiliary relay, con-

nected to the input port of the alarm syem res-

ponsible for changing the panel atus between

armed and disarmed, configurable Wi-Fi Contat-

to output, retention (“Hold button Pressed”) or

pulse (“Press button”)

Yellow

Common (CM) of the auxiliary relay, if the panel

is activated by the GND signal, connect the wire

to the GND, if the panel is activated by the + sign,

connect the wire to the ‘+’

Green Normally open (NO) of the auxiliary relay

3. INTRODUCING THE APP

Step 1: Download the “Contatto” application from your cellphone

app ore.

Android (Google) Operational Syem

Play Store

iOS (Apple) Operational Syem

AppStore

NOTE: The app is not available to the Windows Phone (Microsoft) Operational

Syem and other operational syems on the market, it is only available to the

Operational syems described above.

CONTATTO WI-FI

P06882 - 09/2022

Rev. 2

Step 2: When using the app for the r time, it is necessary to

regier with some basic information, such as an e-mail account,

name, cell phone number and the creation of a code (password).

From the second time one uses the app, their e-mail account and

code (password) will have already been saved. To better illurate

the procedure, refer to the images below:

Step 3: After regiering, one can already login to the account that

has been ju created.

Step 4: From the main (Home) Screen, the next ep is to regier

the device. In order to do so, one can ju press the Menu button (

), then choose the option “Adicionar Dispositivo” (Add device),

select the type of device (Alarm syem, Gate operator, Electric

Fence energizer or Home automation), enter 123ABC into the “Se-

rial” eld or point your cell phone’s QR Code reader at the prod-

uct to search for automatic identication and then tap ‘Adicionar’

(Add). To better illurate the procedure, refer to the images below:

Step 5: At this moment, A screen containing information appears.

Enter 12345678 (Default password) into the “Senha” (Password)

eld and tap “Adicionar” (Add). At this point, a Wi-Fi network called

“WiFi Contatto” appears; one mu close the app and connect to

this network by using the 12345678 Default password.

4. RESET (FACTORY DEFAULT SETTINGS)

To reset the Contatto Wi-Fi settings to the factory default, press

the ‘SW1’ button for at lea 8 seconds. To nd the location of the

button on the board, refer to topic 2 (Connections)”, item 3 (‘SW1’

button).

5. VIEWING MAC AND VERSION

Step 1: To access the version and address of

the device’s MAC (Medium Access Control),

one mu access the main screen of the app,

press and hold either the ‘Portão’ (Gate Opera-

tor), ‘Cerca Elétrica’ (Electric Fence) or ‘Alarme’

(Alarm Syem) icon regiered until the next

screen appears, according to the inructions

below.

Step 2: Tap the button on the upper right corner ( ), and choose

the ‘Congurações’ (Settings) option.

Step 7: To change the password of the CONTATTO WI-FI, it is nec-

essary to follow the ep-by-ep inructions below. In the upper

right corner, tap ‘Conguração’ (Settings). Change the current pass-

word to the desired one in the ‘Senha’ (Password) option. Then,

tap ‘Salvar’ (Save).

Step 8: Disconnect from the “WiFi Contatto” network and connect

to the available Wi-Fi network. At this point of the procedure, one

mu open the app and check if there is a green dot on the upper

part of the “Portão” (Gate Operator), “Cerca” (Electric Fence) and/

or “Alarme” (Alarm syem) buttons. If so, the product is ready to

operate normally.

See below the nal screens, after everything is inalled and ready

to use, for each application:

Showing application activity on ‘Portão’ (Gate operator) mode

Showing application activity on ‘Alarme’ (Alarm syem) mode

Showing application activity on ‘Cerca’ (Electric Fence) mode

Step 6: Open the app again, keep the ‘Portão’ (Gate operator)

button pressed until the ‘Hiórico’ (Hiory) screen appears. Tap

the button on the upper right corner ( ), and choose the ‘Con-

guração’ (Settings) option. Enter the data and password of the

Wi-Fi network available on the place the product is being inalled

and tap ‘Salvar’ (Save). Enter the available Wi-Fi network into the

“Nome do Seu WiFi” (Your Wi-Fi network name) eld. Enter the

password of the available Wi-Fi network into the “Senha do Seu

WiFi” (Your Wi-Fi network password) eld. Enter the amount of

time one wants the relay to remain activated into the “Duração do

Relê” (Duration of the Relay) eld. If one chooses ‘Pulso’ (“Pulse”

= Press button) Mode, the time is zero; otherwise, if one chooses

‘Retenção’ (“Retention” = “Keep button pressed” mode), one mu

choose “Ligado / Desligado (Duração ∞)” (On/O (Duration ∞)).

GENERAL TERMS AND CONDITIONS OF WARRANTY

MOTOPPAR, Indury and Commerce of Automatic Gate Operators Ltd., regiered

with the CNPJ (National Regiry of Legal Entities) under Number 52.605.821/0001-

55, located at 3526 Dr. Labieno da Coa Machado Avenue, Indurial Dirict, Garça

– SP – Brazil, Zip Code 17400-000, manufacturer of PPA Products, hereby guarantees

this product again design, manufacturing or assembly defects and/or supportively

as a result of material quality aws that could make its intended use improper or

inadequate, within a legal period of ninety days from time of acquisition, provided

that the inallation inructions described in the inruction manual are observed.

Due to the credibility and tru placed on PPA products, we will add 275 more days

to the period mentioned above, reaching a warranty period of one year, likewise

counted from the time of acquisition proven by consumer through proof of purchase

(Cuomer Receipt).

In case of defect, within the warranty period, PPA responsibilities are rericted to

the repair or subitution of the product manufactured by the company, under the

following conditions:

1. Repair and readjument of equipment may only be carried out by PPA

Technical Assiance, which is qualied to open, remove, and subitute parts or

components, as well as repair defects covered by this warranty; thus, failure on

observing this guideline and the veried use of any non-original parts will cause

the resignation of this warranty on the part of the user

2. The warranty will not extend to accessories such as cables, screw kit, xing

brackets, power supplies etc.

3. Expenses for packaging, transportation and product reinallation will be sole

responsibility of the consumer

4. The equipment mu be sent directly to the Company responsible for the sale

(manufacturer's representative), through the address contained in the purchase

invoice, properly packed, thus avoiding loss of the warranty

5. Within the additional period of 275 days, visits, and transportation in places

where authorized technical assiance is not available will be charged. The co

of transportation of the product and/or technician will be sole responsibility of

the consumer and

6. The subitution or repair of the product does not prolong the warranty time.

This warranty will be terminated if the product:

1. Is damaged by natural agents, such as atmospheric discharges, oods, wildres,

landslides etc.

2. Is inalled in an improper electric power supply or if it is not according to any of

the inallation inructions displayed on the manual

3. Shows defects caused by droppings, collisions, or any other physical accident

4. Shows signs of product violation or attempted repair by unauthorized personnel

5. Is not used for its intended purpose

6. Is not used under normal conditions

7. Is damaged by accessories or equipment connected to it.

Recommendation:

We recommend that both the inallation and the maintenance of the operator to be

performed by an authorized PPA technical service.

If the product fails or has an improper operation, seek an Authorized Technical

Service to x it.

Password

Advanced options

CANCEL CONNECT

Show password

USE Settings

Settings

Edit Module

Historic

Today 11:23

SETTINGS

MAC address:

Version:

Module WIFI Name

Module password

Relay Duration

No changes

Today 11:23

Today 10:36

SAVE