Yamaha CV820WB El manual del propietario

Tipo
El manual del propietario
1 Remove the old strings. (Refer to the “Removing the old strings”
section in the FC Tremolo System Manual.)
2 Loosen the FC nut locking lever, and remove the locking lever.
3 Remove the locking bolt.
4 Replace the locking blocks 1 and 2.
5 Set the locking bolt.
6 Re-attach the locking lever and tighten lightly.
7 This completes locking block replacement. Install the new strings
and tune the guitar. (Refer to the “Installing the new strings” section
in the FC Tremolo System Manual.)
* Store the set of locking blocks you removed from the guitar
in a safe place for future use.
Changing the Locking Blocks
Loosen
* Set the wider blocks for
the 1st–3rd strings.
* Set the narrower blocks to
the 4th–6th strings.
Tighten
Sting
1st
2nd
3rd
4th
5th
6th
Tuning
C#
G#
E
B
F#
C#
Gauge
.011
.014
.022 (Wound)
.032 (Wound)
.042 (Wound)
.052 (Wound)
CV820WB
About Wes Borland’s String Gauges
FC Nut
The guitar is strung with .010–.046 gauge strings when
shipped from the factory. In order to use the same gauge
strings as Wes Borland you will need to change the locking
blocks in the FC nut. The procedure given in the following
section describes how to change the locking blocks.
FC Nut Part Names
FC Nut Components
*1 : About locking blocks 1 and 2
Included with the guitar is a set of locking blocks that fit the string gauges used by Wes
Borland. Please note that the width of each locking block is different.
Locking Block 1: for strings 1–3 (wider width)
(x2) replacement blocks are included *1
For Normal Gauge Strings
(.009–.042/.010–.046, etc.)
Supplied Replacement: For Wes Borland Gauge
(.011–.052)
Locking Bolt (x1)
Locking Block 2: for strings 4–6 (narrower width)
(x2) replacement blocks are included *1
Locking Block 3 (x1)
Locking Lever x1
The CV820WB is the Wes Borland signature guitar
model.The unique string gauges and tunings used by
Wes Borland are given below.
CV820WB Control System
Owner’s Manual
Bridge Pickup Volume
Neck Pickup Volume
Bridge Pickup
Neck Pickup
Mix
Neck Pickup
Bridge Pickup
Pickup Selector
Locking Block 1
1st–3rd strings (wide)
Locking Block 2
4th–6th strings (narrow)
Head side
Fingerboard side
Head side
Fingerboard side
6.8 mm wide
(0.268 inch)
Marked “1”
Unmarked
6.2 mm wide
(0.244 inch)
Marked “2”
6.0 mm wide
(0.236 inch)
Unmarked
Head side
Fingerboard side
Head side
Fingerboard side
6.6 mm wide
(0.260 inch)

Transcripción de documentos

CV820WB ■ CV820WB Control System 1 Remove the old strings. (Refer to the “Removing the old strings” section in the FC Tremolo System Manual.) 2 Loosen the FC nut locking lever, and remove the locking lever. ■ About Wes Borland’s String Gauges The CV820WB is the Wes Borland signature guitar model.The unique string gauges and tunings used by Wes Borland are given below. Bridge Pickup Neck Pickup Pickup Selector Neck Pickup Volume Changing the Locking Blocks Owner’s Manual Neck Pickup Bridge Pickup Volume Sting Tuning 1st 2nd 3rd 4th 5th 6th C# G# E B F# C# Bridge Pickup Set the locking bolt. 6 Re-attach the locking lever and tighten lightly. Gauge .011 .014 .022 (Wound) .032 (Wound) .042 (Wound) .052 (Wound) The guitar is strung with .010–.046 gauge strings when shipped from the factory. In order to use the same gauge strings as Wes Borland you will need to change the locking blocks in the FC nut. The procedure given in the following section describes how to change the locking blocks. Mix 5 FC Nut Part Names Loosen 3 Remove the locking bolt. FC Nut Components FC Nut Locking Block 1: for strings 1–3 (wider width) (x2) replacement blocks are included *1 Locking Block 3 (x1) Locking Bolt (x1) Tighten Locking Block 2: for strings 4–6 (narrower width) (x2) replacement blocks are included *1 Locking Lever x1 7 *1 : About locking blocks 1 and 2 Included with the guitar is a set of locking blocks that fit the string gauges used by Wes Borland. Please note that the width of each locking block is different. 4 For Normal Gauge Strings Supplied Replacement: For Wes Borland Gauge (.009–.042/.010–.046, etc.) (.011–.052) Replace the locking blocks 1 and 2. * Set the wider blocks for the 1st–3rd strings. Fingerboard side Fingerboard side Head side Head side Locking Block 1 1st–3rd strings (wide) 6.8 mm wide (0.268 inch) 6.6 mm wide (0.260 inch) Marked “1” Unmarked * Set the narrower blocks to the 4th–6th strings. Fingerboard side Head side Fingerboard side Head side * Store the set of locking blocks you removed from the guitar in a safe place for future use. Locking Block 2 4th–6th strings (narrow) 6.0 mm wide (0.236 inch) 6.2 mm wide (0.244 inch) Marked “2” Unmarked This completes locking block replacement. Install the new strings and tune the guitar. (Refer to the “Installing the new strings” section in the FC Tremolo System Manual.)
  • Page 1 1

Yamaha CV820WB El manual del propietario

Tipo
El manual del propietario