Dorel Juvenile IH552TX Guía del usuario

Marca: Dorel Juvenile

Modelo: IH552TX

Categoría: Muebles de bebe

Tipo: Guía del usuario

Flat Surface Mounting

3. Apply 2 pieces of double-

sided mounting tape to the the

back of the crib light and 2

pieces to the back of the control

unit.

4. Adhere the crib light to the

underside of the crib.

Apply ﬁ rm pressure against the

crib light and mounting surface

for 10 seconds to ensure proper

adhesion.

Adhere the control unit to

the side of the crib frame,

nearest to the doorway so the

motion sensor can be promptly

activated.

Apply ﬁ rm pressure against the control unit and mounting surface for

10 seconds to ensure proper adhesion.

5. Use the included (6) cable

management clips to keep

cable off of the ground.

Keep clips off of the ground

and out of reach of children.

Getting Started

Download Safety 1st App

Download the Safety 1st Connected app by searching for Safety 1st in the app

store.

Setup

1. Before mounting, pair the device and test its functionality.

2. Insert the USB cable into the adapter and plug the adapter into the wall outlet.

The crib light will glow red, indicating it is ready for pairing.

3. On your mobile device, follow the step by step instructions in the Safety 1st

Connected app for setup.

4. Once paired, the crib light will glow white.

5. Explore the features and functionality within the Safety 1st Connected app.

Wi-Fi Connectivity

A 2.4GHz Wi-Fi internet connection is required.

Check the Wi-Fi signal strength from your router.

To reduce signal interference or echoes, avoid placing the crib light near major

electrical appliances, large metal or concrete surfaces.

To Reset Device

The device must be plugged in to the power source in order to reset. Press and

hold power button for 6 seconds to reset the device. The crib light will glow red

when the device is reset and ready to be paired in the app.

In the Box

Features

Under Crib Smart Light

You can also:

Send Us a Text: 1-812-203-4747

(US and Canada Only

Carrier Fees May Apply)

Find Us Online: www.safety1st.com

Email Us: [email protected]

Give Us a Call: 1-800-544-1108

(Toll Free, US and Canada Only)

Power &

Reset

Button

Motion &

Ambient

Light

Sensor

Controller

Cable Management Clips Crib Light

Double-Sided

Mounting

Tape

USB

Power

Adapter

3x User

Manual

English,

Spanish,

French

Wi-Fi Connectivity

Motion Detection

Adjustable LED

Color & Brightness

1% - 100%

Select a

preset

scene or

create

your own

Auto dim after

periods of

inactivity

Simple to set

up & install

Also use on

toddler bed as

a nightlight

8.23.21 4358-8170 IH552

1. Clean the desired mounting

surface using a damp cloth, then

dry, ensuring there is no dust or

other residue.

2. Determine the center of the

crib and lay out the crib light,

cables, and cable management

clips. Make sure there will be

enough cable to reach your

nearest electrical outlet once the

crib light is installed.

10 ft

(3 m)

27 in.

(70 cm)

Read all instructions BEFORE assembly and USE of product.

KEEP INSTRUCTIONS FOR FUTURE USE.

not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate

using an antenna of a type and maximum (or lesser) gain approved for

the transmitter by Industry Canada. To reduce potential radio interference

to other users, the antenna type and its gain should be so chosen that

the equivalent isotropically radiated power (e.i.r.p.) is not more than that

necessary for successful communication. This Class B digital apparatus

complies with Canadian ICES-005.

Warranty

Dorel Juvenile Group warrants this product against defective materials

or workmanship. For more information or to make a claim, visit www.

safety1st.com/warranty.

Apple, the Apple logo, and iPhone are trademarks of Apple Inc., registered

in the U.S. and other countries. App Store is a service mark of Apple Inc.

Android is a trademark of Google Inc. Google Play is a trademark of Google

Inc. All other trademarks are the property of their respective owners.

design are trademarks of Dorel Juvenile Group, Inc. (800) 544-1108 www.

safety1st.com. Styles and colors may vary. Los estilos y los colores pueden

variar. Les styles et les couleurs peuvent varier. Made in CHINA. Fabriqué

en CHINE. Hecho en CHINA. Distributed by (distribuido por) (distribrué par)

Dorel Juvenile Group, Inc., 2525 State St., Columbus, IN 47201-7494.

Dorel Juvenile Canada, 2233 Argentia Road, Suite 110, Mississauga, ON

L5N 2X7. Importado y Distribuido en Chile por: Comercial e Industrial Silfa

S.A. - San Ignacio 0201 / Parque Industrial Portezuelo Quilicura, Santiago

Chile. Fono (562) 2339 9000. En Perú por: Comexa S.A. - Los Libertadores

455 – San Isidro, Lima – Perú. Fono (511) 4469014. En Centro América,

Caribe y Ecuador por: Best Brands Group S.A. – Av. Balboa, Bay Mall Plaza,

Planta Baja, local 9, Panamá. - Fono: (507) 300 2884. En Colombia por:

Baby Universe S.A.S. - Vía 40 No. 77-29, Barranquilla, Colombia - Fono:

(575) 353 1110 Importador: DJGM, S.A. DE C.V. Gabriel Mancera No. 1041

Col. Del Valle, Benito Juárez C.P. 03100 México, Ciudad de

México R.F.C. DJG140305GN9 Tel. (55) 67199202

08/21 4358-8170

THE USER SHOULD NOT ATTEMPT TO SERVICE OR REPAIR

THE CRIB LIGHT. ALL SERVICING SHOULD BE REFERRED TO

CONSUMER CARE.

It is essential to check reception regularly. Crib light uses encrypted

transmission over FCC managed frequencies. Always remember to

password protect your Wi-Fi router.

IMPORTANT SAFETY INSTRUCTIONS

• HEAT: The crib light should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances that produce heat.

Also keep these components out of direct sunlight.

• POWER CORD PROTECTION: The power supply cord should be routed

so that it is not likely to be walked on or pinched by items placed upon

or against it. Pay particular attention to the cord at the plug, convenience

receptacle, and at the point it exits from the crib light.

FCC/IC Information

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning this equipment off and on,

the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modiﬁ cations not expressively approved by Dorel

Juvenile Group can void your authority to operate this equipment under

Federal Communications Commission’s rules.

Use of other accessories may not ensure compliance with the FCC

exposure guidelines.

CAUTION: This equipment complies with FCC/IC RSS-102 radiation

exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 8 in. (20 cm)

between the radiator and your body.

IC Information

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may

Disposal

Keep product away from hot, humid areas or strong sunlight, and do not let it get

wet.

Every effort has been made to ensure high standards of reliability of your product.

However, if something does go wrong, please do not try to repair it yourself -

contact Consumer Care for assistance.

At the end of the product life cycle, you should not dispose of this product with

normal household waste. Take this product to a collection point for the recycling

of electrical and electronic equipment.

Some of the product materials can be reused if you take them to a recycling point.

By reusing some parts or raw materials from used products you make an

important contribution to the protection of the environment. Please contact your

recycling center in case you need more information on the collection points in your

area.

Removal

To remove the crib light and control unit, carefully slide a piece of ﬁ shing line or

dental ﬂ oss between the crib, crib light, and control unit.

Then in a sawing motion, cut the adhesive away from the crib. Rub and roll the

remaining adhesive off of the crib, crib light, and control unit.

Note: You may also use the heat from a hair dryer on the lowest setting to help

soften the adhesive to aid in its removal from the crib. Before doing so, remove all

bedding and the mattress from the crib.

• Adult installation is required. Keep small parts away

from children when installing. Exercise care when

unpacking the product.

• This product is intended to be attached UNDER the

crib, where it is least likely to be accessed by the

child when placed inside the crib.

• To prevent possible injury by entanglement, KEEP

OTHER CHILDREN away from cords.

• These products are not toys. DO NOT allow children

to play with them. DO NOT use product if damaged or

broken.

WARNING:

CAUTION:

Colocación en superﬁ cie plana

Para comenzar

Descargar la aplicación de Safety 1st

Descargue la aplicación Safety 1st Connected buscando Safety 1st en la tienda

de aplicaciones.

Conﬁ guración

1. Antes de colocar la luz, empareje el dispositivo y pruebe si funciona bien.

2. Inserte el cable USB en el adaptador y enchufe el adaptador a la toma de

corriente. La luz para cuna brillará de color rojo, lo que indica que está lista para

el emparejamiento.

3. En su dispositivo móvil, siga las instrucciones paso por paso en la aplicación

Safety 1st Connected para la conﬁ guración.

4. Una vez logrado el emparejamiento, la luz para cuna brillará de color blanco.

5. Explore las características y las funciones dentro de la aplicación Safety 1st

Connected.

Conectividad Wi-Fi

Se requiere una conexión a internet Wi-Fi de 2.4GHz.

Revise la velocidad de la señal Wi-Fi en el enrutador.

Para reducir interferencias en la señal o ecos, evite colocar la camarita cerca

de electrodomésticos o superﬁ cies de metal o concreto grandes

Cómo reiniciar el dispositivo

El dispositivo debe estar enchufado a la corriente para poder reiniciarse. Presione

y mantenga presionado el botón de encendido durante 6 segundos para reiniciar

el dispositivo. La luz para cuna brillará de color rojo cuando el dispositivo se

reinicie y esté listo para emparejarse con la aplicación.

En la caja

Características

Luz inteligente para

debajo de la cuna

ESCANEE

AQUÍ PARA

SOLICITAR

AYUDA

También puede:

Enviarnos un mensaje de texto:

1-812-203-4747 (Solo EE. UU. Y

Canadá Se pueden aplicar cargos)

Encuéntrenos en línea:

www.safety1st.com

Enviarnos un correo electrónico:

[email protected]

Llamarnos: 1-800-544-1108

(Sin cargo, Solo EE. UU. Y Canadá)

Botón de

encendido y

reinicio

Sensor de

movimiento

y luz del

ambiente

Control

Ganchos para sujetar el cable Luz para cuna

Cinta bifaz

para la

colocación

Adaptador a

USB

3x Manual

de usuario

Inglés

Español

Francés

Conectividad Wi-Fi

Sensor de

movimiento y luz

del ambiente

Brillo y color de

LED regulable de

1% a 100%

Selecciona

una imagen

preestablecida

o crea una

propia

Oscurecimiento

automático

después de

cierto período de

inactividad

Fácil de

conﬁ gurar e

instalar

También se puede usar

debajo de la cama de los

niños como luz de noche

8.23.21 4358-8170 IH552

3 m

(10 pies)

70 cm

(27 pulg.)

Lee todas las instrucciones ANTES de armar y USAR el producto.

CONSERVA LAS INSTRUCCIONES PARA REFERENCIA FUTURA.

3. Aplique 2 piezas de cinta bifaz

en la parte posterior de la luz

para cuna y 2 piezas en la parte

posterior de la unidad de control.

4. Adhiera la luz para cuna

debajo de la cuna.

Ejerza presión ﬁ rmemente

sobre la luz para cuna y la

superﬁ cie de montaje durante

10 segundos para asegurar que

se adhiera bien.

Adhiera la unidad de control al

costado de la cuna más cercano

a la puerta, de manera que el

sensor de movimiento se active oportunamente.

Ejerza presión ﬁ rmemente sobre la unidad de control y la superﬁ cie de

montaje durante 10 segundos para asegurar que se adhiera bien.

5. Use los ganchos para el

montaje del cable (6) para

sujetar el cable alejado del

piso.

Mantenga los ganchos fuera

de la vista y del alcance de

los niños.

1. Limpie la superﬁ cie donde

desea colocar la luz con un

paño húmedo, luego séquela y

asegúrese de que quede polvo u

otro tipo de suciedad.

2. Determine el centro de la cuna

y disponga la luz para cuna, el

cable y los ganchos para sujetar

el cable. Asegúrese de tener

la suﬁ ciente cantidad de cable

para llegar a la toma de corriente

más cercana una vez que haya

instalado la luz para cuna.

Información de IC

El dispositivo cumple con los estándares RSS exentos de licencia de

Industry Canada. El funcionamiento está sujeto a las dos siguientes

condiciones: (1) este dispositivo no deberá ocasionar interferencias y (2)

este dispositivo deberá aceptar cualquier interferencia, incluso aquella que

produzca un funcionamiento no deseado.

Bajo las normas de Industry Canada, este transmisor de radio solo se

puede usar con una antena de tipo y ganancia máxima (o inferior) aprobada

para el transmisor por Industry Canada. Para reducir las interferencias

potenciales de radio para otros usuarios, se debe seleccionar un tipo de

antena y ganancia para la que la potencia equivalente radiada isotrópica

(e.e.i.i.) no sea superior a la necesaria para la correcta comunicación. Este

aparato digital de Clase B cumple con la norma canadiense ICES-005.

Garantía

Dorel Juvenile Group cubre este producto bajo garantía por defectos

respecto del material o la mano de obra. Para más información o para

realizar un reclamo, consulte www.safety1st.com/warranty

Apple, el logotipo de Apple y iPhone son marcas registradas de Apple Inc.,

registradas en EE. UU. y otros países. App Store es una marca registrada

de Apple Inc.

Android es una marca registrada de Google Inc. Google Play es una marca

registrada de Google Inc. Todas las otras marcas son propiedad de sus

respectivos dueños.