Panasonic KXHNS107 Instrucciones de operación
- Tipo
- Instrucciones de operación
Installation Guide
Home Network System
Garage Door Sensor
Model No. KX-HNS107
Thank you for purchasing a Panasonic product.
This document explains how to install the sensor properly.
For details about how to use the system, refer to the User’s Guide
(page 16).
Please read this document before using the unit and save it for future
reference.
For assistance, please contact us at 1-800-272-7033 or visit our Web
site: http://shop.panasonic.com/support for customers in the U.S.A.
Please register your product: http://shop.panasonic.com/support
In order to use this device:
R Download the latest version of the [Home Network] app.
R Update your hub to the latest firmware version
(version 7.00 or later).
For more information, refer to the User’s Guide (page 16).
Printed in China
HNS107_(en_en)_1210_ver.031.pdf 1 2015/12/10 16:49:06
Introduction
Accessory information ...............3
Important Information
About this system ......................4
For your safety ...........................
4
Important safety instructions ......5
For best performance ................6
Other information .......................6
Setup
Part names and functions ..........8
LED indicator .............................8
Setup overview ..........................9
Inserting the battery ...................9
Registering the sensor .............10
Information about sensor
features ....................................11
Confirming the usage area ......12
Mounting the sensor ................13
Appendix
Features available when using the
[Home Network] app ................16
Accessing the User’s Guide ....16
Specifications ..........................17
FCC and other information ......18
Customer services ...................19
Limited Warranty (ONLY FOR
U.S.A.) .....................................20
2
Table of Contents
HNS107_(en_en)_1210_ver.031.pdf 2 2015/12/10 16:49:06
Accessory information
Supplied accessories
No. Accessory item/Part number Quantity
A
Battery
*
1
1
B
Mounting adaptor
*
2
/PNKL1062Z1
1
C Mounting screws (20 mm (25/32 inches))/XTS4+20AVWC3 2
D Double-sided mounting tapes/PNHS1724Z 2
*1 When replacing the battery, see “Power source” of “Specifications”, page 17
f
or battery information.
*2 The mounting adaptor is attached to the product at the time of shipment.
A
B C D
Other information
R D
esign and specifications are subject to change without notice.
R The illustrations in these instructions may vary slightly from the actual product.
Trademarks
R iPhone and iPad are registered trademarks of Apple Inc.
R Android is a trademark of Google Inc.
R Microsoft, Windows, and Internet Explorer are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
R All other trademarks identified herein are the property of their respective owners.
For a
ssistance, please visit http://shop.panasonic.com/support
3
Introduction
HNS107_(en_en)_1210_ver.031.pdf 3 2015/12/10 16:49:07
About this system
R This system is an auxiliary system; it
is not designed to provide complete
protection from property loss.
Panasonic will not be held
responsible in the event that
property loss occurs while this
system is in operation.
R The system’s wireless features are
subject to interference, therefore
functionality in all situations cannot
be guaranteed. Panasonic will not
be held responsible for injury or
damage to property that occurs in
the event of wireless communication
error or failure.
For your safety
T
o prevent severe injury and loss of
property, read this section carefully
before using the product to ensure
proper and safe operation of your
product.
WARNING
Power connection
R D
o not connect non-specified
devices.
Installation
R I
nstall this product in accordance
with the provided instructions.
R To prevent the risk of fire or
electrical shock, do not expose the
product to rain or any type of
moisture.
R Do not place or use this product
near automatically controlled
devices such as fire alarms. Radio
w
aves emitted from this product may
cause such devices to malfunction
resulting in an accident.
R Install the product only on a vertical
surface. Do not install the product on
a ceiling, as the product may fall,
resulting in damage or injury.
R Keep small parts (screws, etc.) out
of the reach of children. There is a
risk of swallowing. In the event they
are swallowed, seek medical advice
immediately.
R Panasonic will not be held
responsible for damage or injury
caused by improper connection,
installation, or usage.
Operating safeguards
R D
o not disassemble the product.
Medical
R Consult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
determine if they are adequately
shielded from external RF (radio
frequency) energy. DECT features
operate between 1.92 GHz and
1.93 GHz with a peak transmission
power of 115 mW.
R Do not use the product in health
care facilities if any regulations
posted in the area instruct you not to
do so. Hospitals or health care
facilities may be using equipment
that could be sensitive to external
RF energy.
CR Lithium battery
R D
o not recharge, disassemble,
remodel, heat or throw it into fire.
4
For a
ssistance, please visit http://shop.panasonic.com/support
Important Information
HNS107_(en_en)_1210_ver.031.pdf 4 2015/12/10 16:49:07
R D
o not touch the terminals
and
with metal objects.
R R
isk of explosion if battery is
replaced by an incorrect type.
Dispose of used battery according to
local regulations.
R If any electrolyte should come into
contact with your hands or clothes,
wash it off thoroughly with water.
R If any electrolyte should come into
contact with your eyes, never rub
your eyes. Rinse your eyes
thoroughly with water, and then
consult a doctor.
CAUTION
Installation and location
R D
o not mount the product on
plywood less than 25 mm (1 inch)
thick.
CR Lithium battery
R U
se only the battery noted on
page 3.
R Insert the battery correctly.
R Do not leave the battery in an
automobile exposed to direct
sunlight for a long period of time with
the doors and windows closed.
R Remove the battery if you do not
use the product for a long period of
time. Keep it in a cool, dark area.
R Do not replace a battery with wet
hands.
R Keep out of the reach of small
children. There is a risk of
swallowing. If the battery is
swallowed, seek medical attention
immediately.
R Remove the battery if it becomes
unusable. There is a risk of leakage,
overheating, and rupture. Do not
attempt to use a battery if it is
l
eaking.
R Exercise care when handling the
battery. Do not allow conductive
materials such as rings, bracelets, or
keys to touch the battery, otherwise
a short circuit may cause the battery
and/or the conductive material to
overheat and cause burns.
R Do not intentionally pour water on
the battery or allow it to get wet.
There is a risk of fire and smoke. If
the battery becomes wet, remove it
immediately and contact an
authorized service center.
R The battery should be used
correctly, otherwise the product may
be damaged due to battery leakage.
R Do not charge, short-circuit,
disassemble, or heat the battery.
R Do not dispose of batteries in a fire.
Important safety
i
nstructions
When using your product, basic safety
precautions should always be followed
to reduce the risk of fire, electric shock,
and injury to persons, including the
following:
1. Do not use this product near water
for example, near a bathtub,
washbowl, kitchen sink, or laundry
tub, in a wet basement or near a
swimming pool.
2. Use only the batteries indicated in
this document. Do not dispose of
batteries in a fire. They may
explode. Check with local codes for
possible special disposal
instructions.
SAVE THESE INSTRUCTIONS
For a
ssistance, please visit http://shop.panasonic.com/support
5
Important Information
HNS107_(en_en)_1210_ver.031.pdf 5 2015/12/10 16:49:07
For best performance
Hub location/avoiding noise
T
he hub and other compatible
Panasonic devices use radio waves to
communicate with each other.
R For maximum coverage and
noise-free communications, place
your hub:
– at a convenient, high, and central
location with no obstructions
between the product and hub in
an indoor environment.
– away from electronic appliances
such as TVs, radios, personal
computers, wireless devices, or
other phones.
– facing away from radio frequency
transmitters, such as external
antennas of mobile phone cell
stations. (Avoid putting the hub
on a bay window or near a
window.)
R If the reception for a hub location is
not satisfactory, move the hub to
another location for better reception.
Environment
R Keep the product away from
electrical noise generating devices,
such as fluorescent lamps and
motors.
R Do not place heavy objects on top of
the product.
R The product should be kept away
from heat sources such as heaters,
kitchen stoves, etc. It should not be
placed in rooms where the
temperature is less than -20 °C
(-4 °F) or greater than 50 °C
(122 °F). Damp basements should
also be avoided.
R O
perating the product near electrical
appliances may cause interference.
Move away from the electrical
appliances.
Other information
C
AUTION: Risk of explosion if battery
is replaced by an incorrect type.
Dispose of used batteries according to
the instructions.
Routine care
R W
ipe the outer surface of the
product with a soft moist cloth.
R Do not use any cleaning products
that contain alcohol, polish powder,
powder soap, benzine, thinner, wax,
petroleum, or boiling water. Also do
not spray the product with
insecticide, glass cleaner, or hair
spray. This may cause a change in
color or quality of the product.
Information on Disposal in other
C
ountries outside the European
Union
These symbols are only valid in the
European Union. If you wish to discard
these items, please contact your local
authorities or dealer and ask for the
correct method of disposal.
6
For a
ssistance, please visit http://shop.panasonic.com/support
Important Information
HNS107_(en_en)_1210_ver.031.pdf 6 2015/12/10 16:49:07
Part names and
functions
A
D
C
E
B
Front cover
Mounting adaptor release lever
Mounting adaptor
M N
U
sed to confirm the status of the
sensor or register the sensor to
the hub.
LED indicator
LED indicator
You can press M N
and check the
LED indicator to confirm the sensor’s
status. After confirming the sensor’s
status, we recommend turning the LED
indicator off by pressing M
N
again
as soon as possible, otherwise battery
life may be reduced.
Indicator Status
Green, lit Door is closed
Red, lit Door is open
Red,
b
linking
Sensor is out of range
of the hub
Green,
b
linking
slowly
Registration mode
(You pressed and held
M
N)
Off No battery power
Note:
R T
he LED indicator does not indicate
sensor status if the sensor has not
been registered (page 10).
8
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS107_(en_en)_1210_ver.031.pdf 8 2015/12/10 16:49:07
Setup overview
1 Initial setup
Make sure you can access the
system using your mobile device.
For details, refer to the System
Setup Guide included with your
hub.
2 Insert the battery
The sensor is battery powered.
3 Registration
Required only if the sensor was
purchased separately (i.e., not as
part of a bundle).
4 Confirm the installation area
Read the information in this
document to confirm that the
desired installation area is suitable
to proper operation.
5 Installation
Install the sensor in the desired
location.
Inserting the battery
R Use ONLY a CR2 Lithium battery.
R Confirm the polarities (
, ).
1 R
emove the front cover.
R Lift from the indented area (A)
and remove the cover (B).
A
B
2 I
nsert the battery.
3 A
ttach the front cover.
For a
ssistance, please visit http://shop.panasonic.com/support
9
Setup
HNS107_(en_en)_1210_ver.031.pdf 9 2015/12/10 16:49:07
Replacing the battery
Use this procedure when replacing the
battery after installation.
1 Remove the sensor from the
mounting adaptor by pressing the
release lever, sliding the sensor up
and lifting it away from the
mounting adaptor.
2 Remove the front cover.
3 Replace the battery with a new
one.
4 Attach the front cover.
5 Attach the sensor to the mounting
adaptor.
R The sensor will click into place
when it is secured.
R Make sure the “UP” marks on
the back of the sensor and the
inside of the mounting adaptor
point in the same direction.
Registering the
s
ensor
This procedure is not required for
d
evices that were included as part of
a bundle.
Before you can use the sensor, it must
b
e registered to the hub.
If you purchased devices separately
(i.e., not as part of a bundle), you must
register each device to the hub.
You can register each device by using
the registration buttons or the [Home
Network] app.
Using registration buttons
1 Hub:
Press and hold M OTHER
D
EVICEN until the LED indicator
blinks slowly in green.
2 Sensor:
Remove the front cover, and then
press and hold M
N
until the
LED indicator blinks slowly in
green (page 8).
R When registration is complete,
the hub sounds one long beep.
Note:
R To cancel without registering the
sensor, press M
N
on the hub and
on the sensor again.
R If registration fails, the hub sounds
several short beeps.
Using the app
W
hen you register the sensor by using
the [Home Network] app, you can
assign it a name and location. For
more information, refer to the User’s
Guide (page 16).
10
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS107_(en_en)_1210_ver.031.pdf 10 2015/12/10 16:49:07
Information about
sensor features
The garage door sensor utilizes an
accelerometer to detect its orientation.
Please read the following information
before deciding where to install the
garage door sensor.
Note:
R The sensor is not designed to be
used in situations that require high
reliability. We do not recommend
use of the sensor in these situations.
R Panasonic takes no responsibility for
any injury or damage caused by the
use of the garage door sensor.
Compatible garage doors
Vertical
s
ection-type
Swing-up type
How an open door is detected
T
he sensor is installed by mounting it to
the interior-side of your garage door. It
should be mounted in such a way that
it is perpendicular to the ground when
the garage door is closed, and is tilted
when the garage door is opened.
When the garage door has opened far
enough to tilt the sensor beyond the
detection threshold (page 17), the
sensor is triggered.
Note:
R The sensor is not triggered if the
door is opened slightly.
Vertical section-type
A B C
Swing-up type
A B C
Door closed
As door opens, sensor is triggered
Door fully open
For a
ssistance, please visit http://shop.panasonic.com/support
11
Setup
HNS107_(en_en)_1210_ver.031.pdf 11 2015/12/10 16:49:07
Confirming the
usage area
Wireless communication
r
ange
The wireless communication range of
each device in the system from the hub
is approximately 50 m (160 feet)
indoors and approximately 300 m
(1,000 feet) outdoors. Wireless
communication may be unreliable
when the following obstacles are
located between the hub and other
devices.
R Metal doors or screens
R Walls containing aluminum-sheet
insulation
R Walls made of concrete or
corrugated iron
R Double-pane glass windows
R Multiple walls
R When using each device on
separate floors or in different
buildings
Note:
R You can check the sensor’s
communication status by pressing
M
N.
If the LED indicator is lit in
green or red, the sensor is
communicating properly with the
hub. If the LED indicator blinks in
red, it is out of range of the hub.
Usage area cautions
U
sing the sensor in the following areas
may cause deformation, malfunction, or
operational failure.
R In direct sunlight
R Areas exposed to grease or steam,
such as kitchens
R N
ear fire or heating devices
R Near magnetic fields (such as near
microwaves and magnets)
R Areas subject to extreme
temperature changes, such as next
to air conditioners
R Near devices that emit strong radio
waves, such as mobile phones
12
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS107_(en_en)_1210_ver.031.pdf 12 2015/12/10 16:49:07
Mounting the sensor
In most cases, you can mount the
sensor to the garage door using
double-sided tape. In some cases,
such as when mounting the sensor to a
wooden surface, you can use screws.
Installation precautions
R O
bserve the following to avoid the
risk of falling, which could cause
injury or damage to property.
– Mount the sensor on a stable
surface where the sensor will be
adequately supported.
– Do not mount the sensor on
plywood less than 25.4 mm
(1 inch) thick.
R Install the sensor on the inside of the
garage door.
R Mount the sensor near the top of the
garage door. Additionally, we
recommend mounting the sensor
near the left or right edge of the
garage door, so that the sensor is
not directly above the car when the
garage door is open.
Securing with double-sided
tape
Important:
R Make sure the surfaces of the
mounting adaptor and the
installation area of the garage door
are clean and dry before applying
double-sided tape. Take particular
care to remove any oil or grime that
has accumulated on the garage
door.
R Install the sensor on a smooth area
of the garage door. Ideally there
should be no pits or grooves deeper
than 0.5 mm (0.02 inches).
R Once you have used the
double-sided tape, do not reuse it.
R When mounting the sensor in cold
temperatures, observe the following
to ensure optimal adhesion.
– Affix the double-sided tape to the
mounting adaptor indoors, when
the tape and the adaptor are at
room temperature.
– Use a hair dryer or other low-heat
emitting device to warm the
installation surface of the garage
door immediately prior to
adhesion, otherwise adhesion
may be poor and the sensor may
fall.
For a
ssistance, please visit http://shop.panasonic.com/support
13
Setup
HNS107_(en_en)_1210_ver.031.pdf 13 2015/12/10 16:49:07
1 M
ake sure that the front cover and
the mounting adaptor are firmly
attached to the sensor.
2 Affix the double-sided tape to the
mounting adaptor.
R Make sure the tape covers the
screw holes on the mounting
adaptor.
3 A
ttach the sensor to the inside of
the garage door.
R Make sure the mounting
adaptor release lever is facing
down when the garage door is
closed.
R Press firmly to ensure solid
adhesion to the installation
surface.
Removing when secured with
double-sided tape
1 Tie a piece of thread to two sticks,
screwdrivers, etc.
2 Pull the thread tight and use it to
cut the double-sided tape, and
then remove any excess tape (A).
A
14
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS107_(en_en)_1210_ver.031.pdf 14 2015/12/10 16:49:07
Securing with screws
Important:
R Make sure the screws are shorter
than the thickness of the installation
surface.
1 Remove the sensor from the
mounting adaptor by pressing the
release lever (A), sliding the
sensor up and lifting it away from
the mounting adaptor (B).
A
B
2 Use the screws to attach the
mounting adaptor to the inside of
the garage door.
R Make sure the “UP” mark on
the mounting adaptor points
upwards when the garage door
is closed.
UP
UP
A
25.4 mm (1 inch)
3 A
ttach the sensor to the mounting
adaptor.
R T
he sensor will click into place
when it is secured.
R Make sure the “UP” marks on
the back of the sensor and the
inside of the mounting adaptor
point in the same direction.
For a
ssistance, please visit http://shop.panasonic.com/support
15
Setup
HNS107_(en_en)_1210_ver.031.pdf 15 2015/12/10 16:49:07
Features available
when using the
[Home Network] app
Some of the sensor’s features that are
available when using the [Home
Network] app are listed below. For
more information, refer to the User’s
Guide (page 16).
– Alarm system
You can use the app to receive
notifications when the garage door is
opened or left open, arm and disarm
the alarm system, confirm the
current status of the sensor, and
view a log of previous events.
– Sensor integration
You can configure the sensor to
trigger other system events, such as
camera recording, turning on an
electric device (such as a lamp), etc.
(Appropriate device required.)
– Telephone alert
You can configure the system to call
a preprogrammed phone number
when the sensor is triggered.
Accessing the User’s
Guide
The User’s Guide is a collection of
online documentation that helps you
get the most out of the [Home
Network] app.
1 iPhone
®
/iPad
®
Tap in the app’s home screen.
A
ndroid™ devices
Tap
or press your mobile
d
evice’s menu button in the app’s
home screen.
2 Tap [User’s Guide].
Note:
R Microsoft
®
Windows
®
Internet
Explorer
®
8 and earlier versions are
not supported.
R Android 4.1 or later versions are
recommended.
R You can also access the User’s
Guide at the web page listed below.
www.panasonic.net/pcc/support/tel/
h
omenetwork/manual/
16
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS107_(en_en)_1210_ver.031.pdf 16 2015/12/10 16:49:07
Specifications
R Standards
DECT (Digital Enhanced Cordless
Telecommunications)
R Frequency range
DECT: 1.92 GHz – 1.93 GHz
R RF transmission power
DECT: 115 mW (max.)
R Power source
Lithium battery CR2 (CR15H270)
(1 ´ 3.0 V, 850 mAh)
R Battery life
Up to 18 months (when the sensor is
triggered 5 times a day and the
surrounding temperature is approx.
25 °C (77 °F))
R Detection method
3-axis accelerometer
R Operating conditions
-20 °C – 50 °C (-4 °F – 122 °F)
R Detection threshold
When opening the door: Approx. 26°
When closing the door: Approx. 20°
R Dimensions (height ´ width ´
depth)
50 mm ´ 50 mm ´ 24 mm
(1 31/32 inches ´ 1 31/32 inches ´
15/16 inches)
with the mounting adaptor attached
R Mass (weight)
Approx. 30.3 g (1.07 ounces),
excluding the battery, with the
mounting adaptor attached
For a
ssistance, please visit http://shop.panasonic.com/support
17
Appendix
HNS107_(en_en)_1210_ver.031.pdf 17 2015/12/10 16:49:07
FCC and other
information
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Privacy of communications may not be
ensured when using this device.
CAUTION:
Any changes or modifications not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate this
device.
NOTE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
f
ollowing measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an
experienced radio/TV technician for
help.
Some devices operate at frequencies
that may cause interference to nearby
TVs and VCRs. To minimize or prevent
such interference, this device should
not be placed near or on top of a TV or
VCR. If interference is experienced,
move this device further away from the
TV or VCR. This will often reduce or
eliminate interference.
FCC RF Exposure Warning:
R This product complies with FCC
radiation exposure limits set forth for
an uncontrolled environment.
R To comply with FCC RF exposure
requirements, the device must be
installed and operated 20 cm
(8 inches) or more between the
product and all person’s body.
R This product may not be collocated
or operated in conjunction with any
other antenna or transmitter.
Notice:
R FCC ID can be found inside the
sensor.
18
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS107_(en_en)_1210_ver.031.pdf 18 2015/12/10 16:49:07
Customer services
You may also contact us directly at: 1-800-272-7033,
Monday - Friday 9 am to 9 pm;
Saturday - Sunday 10 am to 7 pm, EST.
Accessories!
http://shop.panasonic.com/support
Customer Services Directory
Shop
for all your Panasonic gear
Go to
Get everything you need to get the most out of
your Panasonic products
Accessories & Parts for your Camera, Phone, A/V
products, TV, Computers & Networking, Personal
Care, Home Appliances, Headphones, Ba!eries,
Backup Chargers & more…
For Product Informa"on, Opera"ng Assistance,
Parts, Owner’s Manuals, Dealer and Service info
go to http://shop.panasonic.com/support
For the hearing or speech impaired TTY: 1- 877-833-8855
As of June 2015
For a
ssistance, please visit http://shop.panasonic.com/support
19
Appendix
HNS107_(en_en)_1210_ver.031.pdf 19 2015/12/10 16:49:07
Limited Warranty (ONLY FOR U.S.A.)
Limited Warranty Coverage (For USA Only)
Labor
One (1) Year
Parts
One (1) Year
To submit a new repair request and for quick repair status visit our Web Site at
http://shop.panasonic.com/support
Panasonic Products Limited Warranty
Online Repair Request
Mail-In Service--Online Repair Request
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length
of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts,
(b) replace it with a new or a refurbished equivalent value product, or (c) refund your
purchase price. The decision to repair, replace or refund will be made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the “Parts”
warranty period, there will be no charge for parts. This Limited Warranty excludes both
parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet).
This warranty only applies to products purchased and serviced in the United States.
This warranty is extended only to the original purchaser of a new product which was
not sold “as is”.
Home Network System Products
microSD card (Included model only)
90 days N/A
When shipping the unit, carefully pack, include all supplied accessories listed in the
Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box.
When shipping Lithium Ion batteries please visit our Web Site at
http://shop.panasonic.com/support as Panasonic is committed to providing the most up to
date information. Include a letter detailing the complaint, a return address and provide a
daytime phone number where you can be reached. A valid registered receipt is required
under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL
BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING
DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL
BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF
OF PURCHASE.
Product or Part Name
20
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS107_(en_en)_1210_ver.031.pdf 20 2015/12/10 16:49:07
Limited Warranty Limits and Exclusions
(As examples, this excludes damages for lost time, travel to and from the servicer,
loss of or damage to media or images, data or other memory or recorded content.
The items listed are not exclusive, but for illustration only.)
This warranty ONLY COVERS failures due to defects in materials or workmanship,
and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty
ALSO DOES NOT COVER damages which occurred in shipment, or failures which
are caused by products not supplied by the warrantor, or failures which result from
accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, introduction of sand,
humidity or liquids, commercial use such as hotel, office, restaurant, or other business
or rental use of the product, or service by anyone other than a Factory Service Center
or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY,
ARE YOUR RESPONSIBILITY.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. If a problem with this product develops during or after the warranty period,
you may contact your dealer or Service Center. If the problem is not handled to your
satisfaction, then write to:
Consumer Affairs Department
Panasonic Corporation of North America
661 Independence Pkwy
Chesapeake, VA 23320
As of June 2015
For a
ssistance, please visit http://shop.panasonic.com/support
21
Appendix
HNS107_(en_en)_1210_ver.031.pdf 21 2015/12/10 16:49:07
22
Notes
HNS107_(en_en)_1210_ver.031.pdf 22 2015/12/10 16:49:07
23
Notes
HNS107_(en_en)_1210_ver.031.pdf 23 2015/12/10 16:49:07
1 Use a CR2 lithium battery.
2
Use the Home Network app to access the User’s Guide
and refer to the Troubleshooting section.
IMPORTANT!
If your product is not working properly. . .
Visit our W
eb site: http://shop.panasonic.com/support
LFAQ and troubleshooting hints are available.
For your future reference
W
e recommend keeping a record of the following information to assist
with any repair under warranty.
Serial No. Date of purchase
(found inside the sensor)
N
ame and address of dealer
Attach your purchase receipt here.
Two Riverfront Plaza, Newark, NJ 07102-5490
© Panasonic System Networks Co., Ltd. 2016
HNS107_(en_en)_1210_ver.031.pdf 24 2015/12/10 16:49:07
Guía de instalación
Sistema de red doméstico
Sensor de la puerta del garaje
Modelo n° KX-HNS107
Gracias por adquirir un producto Panasonic.
Este documento explica cómo instalar el sensor de forma correcta. Para ob-
tener detalles sobre cómo usar el sistema, consulte la Guía del usuario (pá-
gina 11).
Lea este documento antes de usar la unidad, y guárdelo para consultarlo en el
futuro.
Para obtener ayuda, comuníquese con nosotros llamando al 1-800-272-7033 o
visite nuestro sitio web: http://shop.panasonic.com/support para clientes en
los EE. UU. (solo en inglés)
Por favor, registre su producto: http://shop.panasonic.com/support
Para utilizar este dispositivo:
R Descargue la versión más reciente de la aplicación [Home Network].
R Actualice el hub a la versión de firmware más reciente (versión 7.00 o
posterior). Para obtener más información, consulte la Guía del usuario
(página 11).
PNQX7762ZA CC0116WK0 (E)
HNS107_(es_es)_1211_ver.021.pdf 1 2015/12/11 12:14:52
Configuración
Nombres de los componentes y
funciones .........................................3
Led indicador ...................................3
Resumen de configuración ..............4
Insertar la batería ............................4
Registro del sensor ..........................5
Información acerca de las
características del sensor ................6
Confirmación del área de uso ..........7
Montaje del sensor ..........................8
Apéndice
Acceso a la Guía del usuario .........11
2
Tabla de Contenido
HNS107_(es_es)_1211_ver.021.pdf 2 2015/12/11 12:14:53
Nombres de los
componentes y
funciones
A
D
C
E
B
Tapa frontal
Palanca de activación del
adaptador de montaje
Adaptador de montaje
M N
Se usa para confirmar el estado del
sensor o para registrar el sensor en el
hub.
Led indicador
Led indicador
Puede oprimir M
N y verificar el Led
indicador para confirmar el estado del
sensor. Tras confirmar el estado del sensor,
recomendamos apagar el Led indicador
volviendo a pulsar M N lo antes posible,
ya que de lo contrario la vida útil de la
batería podría reducirse.
Indicador Estado
Verde, en-
cendido
La puerta está cerrada
Rojo, encen-
dido
La puerta está abierta
Rojo, parpa-
deante
El sensor está fuera de al-
cance del hub
Verde, par-
padeando
lentamente
Modo de registro (Opri-
mió y mantuvo oprimido
M
N)
Apagado Sin batería
Nota:
R El Led indicador no indica el estado del
sensor si el sensor no se ha registrado
(página 5).
Para obtener ayuda, visite http://shop.panasonic.com/support
3
Configuración
HNS107_(es_es)_1211_ver.021.pdf 3 2015/12/11 12:14:53
Resumen de
configuración
1 Configuración inicial
Asegúrese de poder acceder al
sistema mediante su dispositivo móvil.
Para obtener más detalles, consulte la
Guía de configuración del sistema que
viene con su hub.
2 Inserte la batería
El sensor usa batería.
3 Registro
Solo se requiere si se compró el
sensor por separado (es decir, no
como parte de un paquete).
4 Confirme el área de instalación
Lea la información de e
ste documento
para confirmar que el área de
instalación deseada sea la adecuada
para el correcto funcionamiento.
5 Instalación
Instale el sensor en la ubicación
deseada.
Insertar la batería
R Use SOLO una batería de litio CR2.
R Verifique las polaridades (
, ).
1 Quite la tapa frontal.
R Levante del área cóncava (A) y
quite la tapa (B).
A
B
2 Inserte la batería.
3 Coloque la tapa frontal.
4
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS107_(es_es)_1211_ver.021.pdf 4 2015/12/11 12:14:53
Cómo reemplazar la batería
Use este procedimiento cuando reemplace
la batería luego de la instalación.
1 Quite el sensor del adaptador de
montaje al oprimir la palanca de
liberación, deslizar el sensor hacia
arriba y levantarlo del adaptador de
montaje.
2 Quite la tapa frontal.
3 Cambie la batería por una nueva.
4 Coloque la tapa frontal.
5 Coloque el sensor en el adaptador de
montaje.
R El sensor se fijará en su lu
gar
cuando esté asegurado.
R Asegúrese de que las marcas “UP”
de la parte trasera del sensor y del
interior del adaptador de montaje
apunten en la misma dirección.
Registro del sensor
Este procedimiento no es necesario para
unidades que son parte de un paquete.
Antes de poder usar el sensor, debe
registrarlo en el hub.
Si compró los dispositivos por separado (es
decir, no como parte de un paquete), debe
registrar cada dispositivo en el hub.
Puede registrar cada unidad mediante los
botones de registro o la aplicación [Home
Network].
Uso de los botones de registro
1 Hub:
Oprima y mantenga oprimido M
OTHER DEVICEN hasta que el Led
indicador parpadee lentamente en
verde.
2 Sensor:
Quite la tapa frontal y mantenga
oprimido M
N hasta que el Led
indicador parpadee lentamente en
verde (página 3).
R Cuando se ha completado el
registro, el hub emitirá un pitido
largo.
Nota:
R Para cancelar sin registrar el sensor,
oprima M
N en el hub y en el sensor
nuevamente.
R Si el registro falla, el hub emitirá varios
pitidos cortos.
Uso de la aplicación
Cuando registra el sensor con la aplicación
[Home Network], puede asignarle un
nombre y una ubicación. Para obtener más
información, consulte la Guía del usuario
(página 11).
Para obtener ayuda, visite http://shop.panasonic.com/support
5
Configuración
HNS107_(es_es)_1211_ver.021.pdf 5 2015/12/11 12:14:53
Información acerca de
las características del
sensor
El sensor de la puerta del garaje utiliza un
acelerómetro para detectar la orientación.
Lea la información siguiente antes de
decidir dónde instalar el sensor de la puerta
del garaje.
Nota:
R El sensor no está diseñado para usarse
en situaciones que requieran alta
confiabilidad. No recomendamos el uso
del sensor en estas situaciones.
R Panasonic no asume ningu
na
responsabilidad por lesiones o daños
provocados por el uso del sensor para
puerta de garaje.
Puertas de garaje compatibles
De sección vertical Abatibles hacia
arriba
Cómo se detecta una puerta abierta
Para instalar el sensor, es necesario
montarlo en el lado interior de la puerta del
garaje. Se debe montar de manera que
quede perpendicular al suelo cuando se
cierra la puerta del garaje, y que se incline
cuando ésta se abre.
Cuando la puerta del garaje se abre lo
suficiente como para inclinar el sensor más
allá del umbral de detección, el sensor se
activa.
Nota:
R El sensor no se activa si la puerta se
abre suavemente.
De sección vertical
A B C
Abatibles hacia arriba
A B C
Puerta cerrada
Cuando la puerta se abre, el sensor se
activa
Puerta completamente abierta
6
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS107_(es_es)_1211_ver.021.pdf 6 2015/12/11 12:14:53
Confirmación del área
de uso
Alcance de la comunicación
inalámbrica
El alcance de la comunicación inalámbrica
de cada dispositivo en el sistema del hub
es de aproximadamente 50 m (160 pies) en
interiores y de aproximadamente 300 m
(1,000 pies) en el exterior. Es posible que la
comunicación inalámbrica no sea tan
confiable cuando se encuentran los
obstáculos siguientes entre el hub y otros
dispositivos.
R Puertas o pantallas metálicas
R Par
edes que contengan aislamiento de
aluminio
R Paredes de hormigón o hierro corrugado
R Ventanas de vidrio doble
R Varias paredes
R Cuando los dispositivos están en pisos o
edificios diferentes
Nota:
R Puede verificar el estado de la
comunicación del sensor presionando
M
N. Si el Led indicador está
iluminado en verde o rojo, el sensor se
está comunicando de forma adecuada
con el hub. Si el Led indicador parpadea
en rojo, se encuentra fuera de alcance
del hub.
Precauciones respecto al área
de uso
El uso del sensor en las siguientes áreas
puede causar deformación, averías o fallas
de operación.
R A la luz del sol
R En áreas expuestas a grasa o vapor,
como en cocinas
R Cerca del fuego o calefactores
R Cerca de campos magnéticos (como
cerca de hornos microondas e imanes)
R Áreas sujetas a cambios extremos de
temperatura, como cerca de aires
acondicionados
R Cerca de dispositivos que emiten ondas
de radio potentes, como teléfonos
móviles
Para obtener ayuda, visite http://shop.panasonic.com/support
7
Configuración
HNS107_(es_es)_1211_ver.021.pdf 7 2015/12/11 12:14:53
Montaje del sensor
En la mayoría de los casos, es posible
montar el sensor en la puerta del garaje
con cinta de doble cara. En algunos casos,
como cuando se monta el sensor en una
superficie de madera, se pueden usar
tornillos.
Precauciones de instalación
R Siga estas instrucciones para evitar el
riesgo de caída, el cual puede causar
lesiones o daños en la propiedad.
– Monte el sensor sobre una superficie
estable, donde se pueda sostener
correctamente.
– No monte el sensor sobre una
superficie contrachapada que tenga
menos de 25.4 mm (1 pulgada) de
grosor.
R Instale el sensor en el interior de la
puerta del garaje.
R Monte el sensor cerca
de la parte
superior de la puerta del garaje.
Además, recomendamos montar el
sensor cerca del borde izquierdo o
derecho de la puerta del garaje, de
modo que el sensor no quede arriba del
auto cuando se abre la puerta.
Ajuste con cinta adhesiva de
doble cara
Importante:
R Antes de colocar la cinta adhesiva de
doble cara, asegúrese de que las
superficies del adaptador de montaje y
el área de instalación de la puerta del
garaje estén limpias y secas. Tenga
especial cuidado y quite el aceite o la
suciedad que se haya acumulado en la
puerta del garaje.
R Instale el sensor en una superficie suave
de la puerta del garaje. Lo ideal
es que
no haya hendiduras ni ranuras de más
de 0.5 mm (0.02 pulgadas) de
profundidad.
R Una vez que haya utilizado la cinta de
doble cara, no la vuelva a utilizar.
R Si monta el el sensor cuando la
temperatura es baja, siga estas
instrucciones para asegurar una
adhesión óptima.
– Una vez que la cinta y el adaptador
estén a temperatura ambiente, fije la
cinta de doble cara en la parte del
adaptador de montaje que queda en
el interior.
– Antes de colocar la cinta, use un
secador de pelo u otro dispositivo
que emita calor para calentar la
superficie de instalación de la puerta
del garaje; de lo contrario, es posible
que la adhesión no sea buena y el
sensor se caiga.
8
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS107_(es_es)_1211_ver.021.pdf 8 2015/12/11 12:14:53
1 Asegúrese de que la tapa frontal y el
adaptador de montaje estén
firmemente adheridos al sensor.
2 Coloque la cinta de doble cara en el
adaptador de montaje.
R Asegúrese de que la cinta cubra
los hoyos de los tornillos en el
adaptador de montaje.
3 Coloque el sensor en la parte interior
de la puerta del garaje.
R Asegúrese de que la palanca de
activación del adaptador de
montaje apunte hacia abajo
cuando se cierra la puerta del
garaje.
R Presione con firmeza para
asegurar una adhesión sólida a la
superficie de instalación.
Cómo extraer cuando se asegura con
cinta adhesiva de doble cara
1 Ate un pedazo de hilo a dos palos,
destornilladores, etc.
2 Tire firmemente del hilo y úselo para
cortar la cinta de doble cara, y luego
elimine cualquier exceso de cinta (A).
A
Para obtener ayuda, visite http://shop.panasonic.com/support
9
Configuración
HNS107_(es_es)_1211_ver.021.pdf 9 2015/12/11 12:14:53
Ajuste con tornillos
Importante:
R Asegúrese de que el largo de los
tornillos sea menor que el grosor de la
superficie de instalación.
1 Quite el sensor del adaptador de
montaje al oprimir la palanca de
liberación (A), deslizar el sensor
hacia arriba y levantarlo del adaptador
de montaje (B).
A
B
2 Utilice los tornillos para fijar el
adaptador de montaje en la parte
interior de la puerta del garaje.
R Asegúrese de que la marca “UP”
del adaptador de montaje apunte
hacia arriba cuando la puerta del
garaje está cerrada.
UP
UP
A
25.4 mm (1 pulgada)
3 Coloque el sensor en el adaptador de
montaje.
R El sensor se fijará en su lugar
cuando esté asegurado.
R Asegúrese de que las marcas “UP”
de la parte trasera del sensor y del
interior del adaptador de montaje
apunten en la misma dirección.
10
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS107_(es_es)_1211_ver.021.pdf 10 2015/12/11 12:14:53
Acceso a la Guía del
usuario
La Guía del usuario es una colección de
documentación en línea que lo ayuda a
aprovechar al máximo la aplicación [Home
Network].
1 iPhone
®
/iPad
®
Toque
en la pantalla de inicio de
la aplicación.
Dispositivos Android™
Toque
u oprima el botón menú de
su dispositivo en la pantalla de inicio
de la aplicación.
2 Toque [Guía del Usuario].
Nota:
R No se admite Microsoft
®
Windows
®
Internet Explorer
®
8 y versiones
anteriores.
R Se recomienda Android 4.1 y versiones
posteriores.
R También puede acceder a la Guía del
usuario mediante la página web a
continuación.
www.panasonic.net/pcc/support/tel/
homenetwork/manual/
Para obtener ayuda, visite http://shop.panasonic.com/support
11
Apéndice
HNS107_(es_es)_1211_ver.021.pdf 11 2015/12/11 12:14:54
HNS107_(es_es)_1211_ver.021.pdf 12 2015/12/11 12:14:54
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Panasonic KXHNS107 Instrucciones de operación
- Tipo
- Instrucciones de operación
en otros idiomas
Artículos relacionados
-
Panasonic KXHNS107 Instrucciones de operación
-
-
-
-
-
-
-
-
-