Installation Guide
Home Network System
Motion Sensor
Model No. KX-HNS102
Thank you for purchasing a Panasonic product.
This document explains how to install the motion sensor properly.
For details about how to use the system, refer to the User’s Guide
(page 14).
Please read this document before using the unit and save it for future
reference.
For assistance, please contact us at 1-800-272-7033 or visit our Web
site: http://shop.panasonic.com/support for customers in the U.S.A.
Please register your product: http://shop.panasonic.com/support
Printed in China
HNS102_(en_en)_1008_ver.201.pdf 1 2015/10/19 10:05:18
Introduction
Accessory information ...............3
Important Information
About this system ......................4
For your safety ...........................
4
Important safety instructions ......5
For best performance ................5
Other information .......................6
Setup
Part names and functions ..........7
LED indicator .............................7
Setup overview ..........................7
Inserting the batteries ................8
Registering the motion
sensor ........................................8
Information about sensor
features ......................................9
Confirming the usage area ......11
Wall mounting ..........................12
Appendix
Testing the motion sensor .......14
Adjusting the sensor
sensitivity .................................14
Features available when using the
[Home Network] app ................14
Accessing the User’s Guide ....14
Specifications ..........................15
FCC and other information ......16
Customer services ...................17
Limited Warranty (ONLY FOR
U.S.A.) .....................................18
2
Table of Contents
HNS102_(en_en)_1008_ver.201.pdf 2 2015/10/19 10:05:18
Accessory information
Supplied accessories
No. Accessory item/Part number Quantity
A
Batteries
*
1
2
B
Wall mounting adaptor
*
2
/PNKK1111Z1
1
C Wall mounting screws (25 mm (1 inch))/XTB4+25AVW 2
*1 When replacing batteries, see “Power source” of “Specifications”, page 15
f
or battery information.
*2 The motion sensor can be wall mounted with or without the wall mounting
adaptor (page 12).
A
B C
Other information
R D
esign and specifications are subject to change without notice.
R The illustrations in these instructions may vary slightly from the actual product.
Trademarks
R i
Phone and iPad are registered trademarks of Apple Inc.
R Android is a trademark of Google Inc.
R Microsoft, Windows, and Internet Explorer are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
R All other trademarks identified herein are the property of their respective owners.
For a
ssistance, please visit http://shop.panasonic.com/support
3
Introduction
HNS102_(en_en)_1008_ver.201.pdf 3 2015/10/19 10:05:19
About this system
R This system is an auxiliary system; it
is not designed to provide complete
protection from property loss.
Panasonic will not be held
responsible in the event that
property loss occurs while this
system is in operation.
R The system’s wireless features are
subject to interference, therefore
functionality in all situations cannot
be guaranteed. Panasonic will not
be held responsible for injury or
damage to property that occurs in
the event of wireless communication
error or failure.
For your safety
T
o prevent severe injury and loss of life/
property, read this section carefully
before using the product to ensure
proper and safe operation of your
product.
WARNING
Power connection
R U
se only the power source marked
on the product.
R Do not connect non-specified
devices.
Installation
R T
o prevent the risk of fire or
electrical shock, do not expose the
product to rain or any type of
moisture.
R Do not place or use this product
near automatically controlled
devices such as automatic doors
a
nd fire alarms. Radio waves
emitted from this product may cause
such devices to malfunction
resulting in an accident.
R Keep small parts (screws, etc.) out
of the reach of children. There is a
risk of swallowing. In the event they
are swallowed, seek medical advice
immediately.
Operating safeguards
R D
o not disassemble the product.
Medical
R C
onsult the manufacturer of any
personal medical devices, such as
pacemakers or hearing aids, to
determine if they are adequately
shielded from external RF (radio
frequency) energy. DECT features
operate between 1.92 GHz and
1.93 GHz with a peak transmission
power of 115 mW.
R Do not use the product in health
care facilities if any regulations
posted in the area instruct you not to
do so. Hospitals or health care
facilities may be using equipment
that could be sensitive to external
RF energy.
CAUTION
Battery
R The batteries should be used
correctly, otherwise the product may
be damaged due to battery leakage.
R Do not charge, short-circuit,
disassemble, or heat the batteries.
R Do not dispose of batteries in a fire.
R Remove all the batteries when
replacing.
4
For a
ssistance, please visit http://shop.panasonic.com/support
Important Information
HNS102_(en_en)_1008_ver.201.pdf 4 2015/10/19 10:05:19
R D
o not mix old, new or different
types of batteries.
R It is recommended that batteries are
replaced annually.
R Keep out of the reach of small
children. There is a risk of
swallowing. If the battery is
swallowed, seek medical attention
immediately.
R Remove the battery if it becomes
unusable. There is a risk of leakage,
overheating, and rupture. Do not
attempt to use a battery if it is
leaking.
R Do not intentionally pour water on
the battery or allow it to get wet.
There is a risk of fire and smoke. If
the battery becomes wet, remove it
immediately and contact an
authorized service center.
Important safety
i
nstructions
When using your product, basic safety
precautions should always be followed
to reduce the risk of fire, electric shock,
and injury to persons, including the
following:
1. Do not use this product near water
for example, near a bathtub,
washbowl, kitchen sink, or laundry
tub, in a wet basement or near a
swimming pool.
2. Use only the batteries indicated in
this document. Do not dispose of
batteries in a fire. They may
explode. Check with local codes for
possible special disposal
instructions.
SAVE THESE INSTRUCTIONS
For best performance
Hub location/avoiding noise
T
he hub and other compatible
Panasonic devices use radio waves to
communicate with each other.
R For maximum coverage and
noise-free communications, place
your hub:
– at a convenient, high, and central
location with no obstructions
between the product and hub in
an indoor environment.
– away from electronic appliances
such as TVs, radios, personal
computers, wireless devices, or
other phones.
– facing away from radio frequency
transmitters, such as external
antennas of mobile phone cell
stations. (Avoid putting the hub
on a bay window or near a
window.)
R If the reception for a hub location is
not satisfactory, move the hub to
another location for better reception.
Environment
R Keep the product away from
electrical noise generating devices,
such as fluorescent lamps and
motors.
R The product should be kept free
from excessive smoke, dust, high
temperature, and vibration.
R The product should not be exposed
to direct sunlight.
R Do not place heavy objects on top of
the product.
R The product should be kept away
from heat sources such as heaters,
kitchen stoves, etc. It should not be
placed in rooms where the
For a
ssistance, please visit http://shop.panasonic.com/support
5
Important Information
HNS102_(en_en)_1008_ver.201.pdf 5 2015/10/19 10:05:19
temperature is less than 0 °C (32 °F)
o
r greater than 40 °C (104 °F).
Damp basements should also be
avoided.
R Operating the product near electrical
appliances may cause interference.
Move away from the electrical
appliances.
Other information
C
AUTION: Risk of explosion if battery
is replaced by an incorrect type.
Dispose of used batteries according to
the instructions.
Routine care
R W
ipe the outer surface of the
product with a soft moist cloth.
R Do not use benzine, thinner, or any
abrasive powder.
Information on Disposal in other
C
ountries outside the European
Union
These symbols are only valid in the
European Union. If you wish to discard
these items, please contact your local
authorities or dealer and ask for the
correct method of disposal.
Note for the battery removal
p
rocedure
Refer to “Inserting the batteries” on
page 8.
Notice
6
For a
ssistance, please visit http://shop.panasonic.com/support
Important Information
HNS102_(en_en)_1008_ver.201.pdf 6 2015/10/19 10:05:19
Part names and
functions
A
B
C
D
E
Infrared sensor
LED indicator
MH
IGHN/MLOWN
Used to change the sensor
sensitivity (page 14).
Rear cover
M N
U
sed to confirm the status of the
sensor or register the sensor to
the hub.
LED indicator
Y
ou can press M
N
and check the
LED indicator to confirm the sensor’s
status.
Indicator Status
Green, lit No motion detected
Red, lit Motion was detected
Indicator Status
Red,
b
linking
Sensor is out of range
of the hub
Green,
b
linking
slowly
Registration mode
(You pressed and held
M N)
Off No battery power
Note:
R T
he LED indicator does not indicate
sensor status if the sensor has not
been registered (page 8).
Setup overview
1 Initial setup
Make sure you can access the
system using your mobile device.
For details, refer to the System
Setup Guide included with your
hub.
2 Insert the batteries
The motion sensor is battery
powered.
3 Registration
Required only if the motion sensor
was purchased separately (i.e.,
not as part of a bundle).
4 Confirm the installation area
Read the information in this
document to confirm that the
desired installation area is suitable
to proper operation.
5 Installation
Install the motion sensor in the
desired location.
For a
ssistance, please visit http://shop.panasonic.com/support
7
Setup
HNS102_(en_en)_1008_ver.201.pdf 7 2015/10/19 10:05:19
Inserting the
batteries
R USE ONLY Alkaline batteries AA
(LR6) size.
R Do NOT use Manganese/Ni-Cd/
Ni-MH batteries.
R Confirm the polarities ( , ).
1 R
emove the rear cover by
pressing the upper sides of the
cover (A) and sliding it down (B).
A
B
2 I
nsert the batteries.
3 I
nstall the rear cover.
R Place it with the “
” mark
f
acing upwards and slide it.
Registering the
m
otion sensor
This procedure is not required for
d
evices that were included as part of
a bundle.
Before you can use the motion sensor,
it must be registered to the hub.
If you purchased devices separately
(i.e., not as part of a bundle), you must
register each device to the hub.
You can register each device by using
the registration buttons or the [Home
Network] app.
8
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS102_(en_en)_1008_ver.201.pdf 8 2015/10/19 10:05:19
Using registration buttons
1 Hub:
Press and hold M OTHER
D
EVICEN until the LED indicator
blinks slowly in green.
2 Motion sensor:
Press and hold M
N
until the
LED indicator blinks slowly in
green (page 7).
R When registration is complete,
the hub sounds one long beep.
Note:
R To cancel without registering the
sensor, press M
N
on the hub and
on the sensor again.
R If registration fails, the hub sounds
several short beeps.
Using the app
W
hen you register the motion sensor
by using the [Home Network] app, you
can assign a name to your devices and
group them by location. For more
information, refer to the User’s Guide
(page 14).
Information about
s
ensor features
The motion sensor utilizes an infrared
sensor (i.e., heat sensor).
Please read the following information
before deciding where to install the
motion sensor.
Note:
R The motion sensor’s sensor features
are not designed to be used in
situations that require high reliability.
We do not recommend use of the
motion sensor’s sensor features in
t
hese situations.
R Panasonic takes no responsibility for
any injury or damage caused by the
use of the motion sensor.
Using heat to detect motion
T
he motion sensor’s infrared sensor
can detect motion by recognizing
temperature differences that occur
within the range of the sensor. It does
this by detecting the infrared rays that
are emitted naturally by people,
animals, etc., which correlate to the
object’s temperature. The detection
range is indicated in the illustration by
the gray area in front of the motion
sensor.
Detection range when looking from
a
bove
1
1
Horizontal detection range:
a
pprox. 90°
For a
ssistance, please visit http://shop.panasonic.com/support
9
Setup
HNS102_(en_en)_1008_ver.201.pdf 9 2015/10/19 10:05:19
Detection range when looking from
the side
1
2
1
Vertical detection range: approx.
2
0°
2
Distance of detectable motion:
a
pprox. 5 m (16.4 feet)
Note:
R D
etection becomes difficult when
there is little difference between the
temperatures of objects and the
surrounding environment, such as
during summer. Conversely,
detection becomes easier when
there is a large difference between
the temperatures of objects and the
surrounding environment, such as
during winter or at night.
R Detection does not occur when there
are obstacles in front of the infrared
sensor. Remove the obstacles or
change the installation location.
Direction of motion
I
t is easier to detect objects that move
sideways in front of the motion sensor,
and more difficult to detect objects that
move directly toward the front of the
m
otion sensor.
D
A
B
C
It is difficult to detect movement
d
irectly towards the front of the
motion sensor.
It is easy to detect movement
s
ideways in front of the motion
sensor.
Detection range
Motion sensor
10
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS102_(en_en)_1008_ver.201.pdf 10 2015/10/19 10:05:19
Confirming the
usage area
Wireless communication
r
ange
The wireless communication range of
each device in the system from the hub
is approximately 50 m (160 feet)
indoors and approximately 300 m
(1,000 feet) outdoors. Wireless
communication may be unreliable
when the following obstacles are
located between the hub and other
devices.
R Metal doors or screens
R Walls containing aluminum-sheet
insulation
R Walls made of concrete or
corrugated iron
R Double-pane glass windows
R Multiple walls
R When using each device on
separate floors or in different
buildings
Note:
R You can check the motion sensor’s
communication status by pressing
M
N.
If the LED indicator is lit in
green or red, the sensor is
communicating properly with the
hub. If the LED indicator blinks in
red, it is out of range of the hub.
Usage area cautions
U
sing the motion sensor in the
following areas may cause
deformation, malfunction, or
operational failure.
R In direct sunlight
R A
reas exposed to grease or steam,
such as kitchens
R Near fire or heating devices
R Near magnetic fields (such as near
microwaves and magnets)
R Areas subject to extreme
temperature changes, such as next
to air conditioners
R Areas with reflective objects, such
as glass, that can interfere with
detection of temperature variation
R Areas where the temperature is
affected by strong illuminating
objects (such as fluorescent lights)
R Near devices that emit strong radio
waves, such as mobile phones
For a
ssistance, please visit http://shop.panasonic.com/support
11
Setup
HNS102_(en_en)_1008_ver.201.pdf 11 2015/10/19 10:05:19
Wall mounting
There are two methods for wall
mounting the motion sensor. To mount
the sensor flat against the wall, use the
rear cover. To mount the sensor so that
it faces 45° to the left or right, use the
wall mounting adaptor.
Mounting examples
*
1
of the rear
cover and wall mounting adaptor
1
A
Rear cover
2
B
Wall mounting
adaptor
*1 View of looking from above.
N
ote:
R Mount the motion sensor on the
stable location where the motion
sensor can be adequately supported
when mounting.
R Do not mount motion sensor on a
soft material. It may fall down, break
or cause injury.
R Do not mount the motion sensor on
the following places: gypsum board,
ALC (autoclaved lightweight cellular
concrete), concrete block, plywood
less than 25.4 mm (1 inch) thick, etc.
Using the rear cover
1 Remove the rear cover by
pressing the upper sides of the
cover (A) and sliding it down (B).
A
B
2 A
ttach the rear cover to the wall by
using screws (
1
).
R P
lace the rear cover with “UP”
mark facing upwards.
R
2
37 mm (1 15/32 inches)
U
P
2
1
UP
1
12
For a
ssistance, please visit http://shop.panasonic.com/support
Setup
HNS102_(en_en)_1008_ver.201.pdf 12 2015/10/19 10:05:19
3 A
ttach the motion sensor to the
rear cover.
R Insert the grooves on the
motion sensor to the 4 tabs on
the rear cover, and then push
down the motion sensor.
U
P
Using the wall mounting adaptor
1 R
emove the rear cover by
pressing the upper sides of the
cover (A) and then sliding it down
(B).
A
B
2 A
ttach the wall mounting adaptor
to the wall by using screws (
1
).
R P
lace the wall mounting
adaptor with “UP” mark facing
upwards.
R
2
21 mm (27/32 inches)
2
UP
1
1
3 A
ttach the motion sensor to the
wall mounting adaptor.
R Insert the grooves on the
motion sensor to the 4 tabs on
the wall mounting adaptor, and
then push down the motion
sensor.
For a
ssistance, please visit http://shop.panasonic.com/support
13
Setup
HNS102_(en_en)_1008_ver.201.pdf 13 2015/10/19 10:05:19
Testing the motion
sensor
You can observe the motion sensor’s
LED indicator and test the performance
of the motion sensor.
1 Press M N.
2 M
ove to an area near the motion
sensor.
3 While moving near the motion
sensor, observe the LED indicator.
R When motion is detected, the
LED indicator lights in red.
4 Note the areas where movement
is detected.
5 Press M
N
again.
Adjusting the sensor
s
ensitivity
You can use the MHIGHN/MLOWN switch
(page 7) to adjust the sensor’s
sensitivity. If the sensor often makes
incorrect detections, such as in areas
with frequent and substantial
temperature fluctuations, set the switch
to the MLOWN position.
Note:
R When the switch is in the MLOWN
position, the sensor detection range
is reduced by about half (compared
to when the switch is in the MHIGHN
position).
Features available
when using the
[Home Network] app
Some of the motion sensor’s features
that are available when using the
[Home Network] app are listed below.
For more information, refer to the
User’s Guide (page 14).
– Alarm system
You can use the app to arm and
disarm the alarm system, confirm
the current status of the sensor, and
view a log of previous events.
– Sensor integration
You can configure the motion sensor
to trigger other system events, such
as camera recording, turning on an
electric device (such as a lamp), etc.
(Appropriate device required.)
– Telephone alert
You can configure the system to call
a preprogrammed phone number
when the motion sensor is triggered.
Accessing the User’s
G
uide
The User’s Guide is a collection of
online documentation that helps you
get the most out of the [Home
Network] app.
1 iPhone
®
/iPad
®
Tap
in the app’s home screen.
A
ndroid™ devices
Tap
or press your mobile
d
evice’s menu button in the app’s
home screen.
2 Tap [User’s Guide].
14
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS102_(en_en)_1008_ver.201.pdf 14 2015/10/19 10:05:19
Note:
R M
icrosoft
®
Windows
®
Internet
Explorer
®
8 and earlier versions are
not supported.
R Android 4.1 or later versions are
recommended.
R You can also access the User’s
Guide at the web page listed below.
www.panasonic.net/pcc/support/tel/
h
omenetwork/manual/
Specifications
R S
tandards
DECT (Digital Enhanced Cordless
Telecommunications)
R Frequency range
DECT: 1.92 GHz – 1.93 GHz
R RF transmission power
DECT: 115 mW (max.)
R Power source
AA (LR6) Alkaline battery (2 ´ 1.5 V)
R Operating conditions
0 °C – 40 °C (32 °F – 104 °F)
R Sensor detection method
Pyroelectric infrared sensor (heat
sensor)
R Heat sensor detection range
Horizontal: approx. ±45°
Vertical: approx. ±10°
Distance
*1
:
approx. 5 m (16.4 feet) when the
sensitivity switch is in the MHIGHN
position
approx. 2.5 m (8.2 feet) when the
sensitivity switch is in the MLOWN
position
R B
attery life
Up to 1 year (when motion is
detected 50 times a day and the
surrounding temperature is approx.
25 °C (77 °F))
R Dimensions (height ´ width ´
depth)
– With the rear cover attached:
Approx. 72 mm ´ 73 mm ´
39 mm (2 27/32 inches ´
2 7/8 inches ´ 1 17/32 inches)
– With the wall mounting adaptor
attached:
Approx. 72 mm ´ 73 mm ´
61 mm (2 27/32 inches ´
2 7/8 inches ´ 2 13/32 inches)
R Mass (weight)
– With the rear cover attached:
Approx. 70 g (0.15 lb), excluding
the batteries
– With the wall mounting adaptor
attached:
Approx. 77 g (0.17 lb), excluding
the batteries
*1 When the surrounding
temperature is approx. 25 °C
(77 °F).
For a
ssistance, please visit http://shop.panasonic.com/support
15
Appendix
HNS102_(en_en)_1008_ver.201.pdf 15 2015/10/19 10:05:19
FCC and other
information
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Privacy of communications may not be
ensured when using this device.
CAUTION:
Any changes or modifications not
expressly approved by the party
responsible for compliance could void
the user’s authority to operate this
device.
NOTE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
in a residential installation. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is no
guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
f
ollowing measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
– Consult the dealer or an
experienced radio/TV technician for
help.
Some devices operate at frequencies
that may cause interference to nearby
TVs and VCRs. To minimize or prevent
such interference, this device should
not be placed near or on top of a TV or
VCR. If interference is experienced,
move this device further away from the
TV or VCR. This will often reduce or
eliminate interference.
FCC RF Exposure Warning:
R This product complies with FCC
radiation exposure limits set forth for
an uncontrolled environment.
R To comply with FCC RF exposure
requirements, the device must be
installed and operated 20 cm
(8 inches) or more between the
product and all person’s body.
R This product may not be collocated
or operated in conjunction with any
other antenna or transmitter.
R For body-worn operation, the device
must be used only with a
non-metallic accessory. Use of other
accessories may not ensure
compliance with FCC RF exposure
requirements.
Notice:
R FCC ID can be found inside the
battery compartment.
16
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS102_(en_en)_1008_ver.201.pdf 16 2015/10/19 10:05:19
Customer services
You may also contact us directly at: 1-800-272-7033,
Monday - Friday 9 am to 9 pm;
Saturday - Sunday 10 am to 7 pm, EST.
Accessories!
http://shop.panasonic.com/support
Customer Services Directory
Shop
for all your Panasonic gear
Go to
Get everything you need to get the most out of
your Panasonic products
Accessories & Parts for your Camera, Phone, A/V
products, TV, Computers & Networking, Personal
Care, Home Appliances, Headphones, Ba!eries,
Backup Chargers & more…
For Product Informa"on, Opera"ng Assistance,
Parts, Owner’s Manuals, Dealer and Service info
go to http://shop.panasonic.com/support
For the hearing or speech impaired TTY: 1- 877-833-8855
As of June 2015
For a
ssistance, please visit http://shop.panasonic.com/support
17
Appendix
HNS102_(en_en)_1008_ver.201.pdf 17 2015/10/19 10:05:19
Limited Warranty (ONLY FOR U.S.A.)
Limited Warranty Coverage (For USA Only)
Labor
One (1) Year
Parts
One (1) Year
To submit a new repair request and for quick repair status visit our Web Site at
http://shop.panasonic.com/support
Panasonic Products Limited Warranty
Online Repair Request
Mail-In Service--Online Repair Request
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length
of the period indicated on the chart below, which starts with the date of original purchase
(“warranty period”), at its option either (a) repair your product with new or refurbished parts,
(b) replace it with a new or a refurbished equivalent value product, or (c) refund your
purchase price. The decision to repair, replace or refund will be made by the warrantor.
During the “Labor” warranty period there will be no charge for labor. During the “Parts”
warranty period, there will be no charge for parts. This Limited Warranty excludes both
parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet).
This warranty only applies to products purchased and serviced in the United States.
This warranty is extended only to the original purchaser of a new product which was
not sold “as is”.
Home Network System Products
microSD card (Included model only)
90 days N/A
When shipping the unit, carefully pack, include all supplied accessories listed in the
Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box.
When shipping Lithium Ion batteries please visit our Web Site at
http://shop.panasonic.com/support as Panasonic is committed to providing the most up to
date information. Include a letter detailing the complaint, a return address and provide a
daytime phone number where you can be reached. A valid registered receipt is required
under the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL
BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING
DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL
BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF
OF PURCHASE.
Product or Part Name
18
For a
ssistance, please visit http://shop.panasonic.com/support
Appendix
HNS102_(en_en)_1008_ver.201.pdf 18 2015/10/19 10:05:19
Limited Warranty Limits and Exclusions
(As examples, this excludes damages for lost time, travel to and from the servicer,
loss of or damage to media or images, data or other memory or recorded content.
The items listed are not exclusive, but for illustration only.)
This warranty ONLY COVERS failures due to defects in materials or workmanship,
and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty
ALSO DOES NOT COVER damages which occurred in shipment, or failures which
are caused by products not supplied by the warrantor, or failures which result from
accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, introduction of sand,
humidity or liquids, commercial use such as hotel, office, restaurant, or other business
or rental use of the product, or service by anyone other than a Factory Service Center
or other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY,
ARE YOUR RESPONSIBILITY.
Some states do not allow the exclusion or limitation of incidental or consequential damages,
or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state. If a problem with this product develops during or after the warranty period,
you may contact your dealer or Service Center. If the problem is not handled to your
satisfaction, then write to:
Consumer Affairs Department
Panasonic Corporation of North America
661 Independence Pkwy
Chesapeake, VA 23320
As of June 2015
For a
ssistance, please visit http://shop.panasonic.com/support
19
Appendix
HNS102_(en_en)_1008_ver.201.pdf 19 2015/10/19 10:05:19
1
2
Use alkaline batteries.
(Rechargeable Ni-MH batteries CANNOT be used.)
Use the Home Network app to access the User’s Guide
and refer to the Troubleshooting section.
IMPORTANT!
If your product is not working properly. . .
Visit our Web site: http://shop.panasonic.com/support
LFAQ and troubleshooting hints are available.
For your future reference
W
e recommend keeping a record of the following information to assist
with any repair under warranty.
Serial No. Date of purchase
(found inside the battery compartment)
N
ame and address of dealer
Attach your purchase receipt here.
Two Riverfront Plaza, Newark, NJ 07102-5490
© Panasonic System Networks Co., Ltd. 2014
HNS102_(en_en)_1008_ver.201.pdf 20 2015/10/19 10:05:19
Guía de instalación
Sistema de red doméstico
Sensor de Movimiento
Modelo n° KX-HNS102
Gracias por adquirir un producto Panasonic.
Este documento explica cómo instalar el sensor de movimiento de forma co-
rrecta.
Para obtener detalles sobre cómo usar el sistema, consulte la Guía del usua-
rio (página 10).
Lea este documento antes de usar la unidad, y guárdelo para consultarlo en el
futuro.
Para obtener ayuda, comuníquese con nosotros llamando al 1-800-272-7033 o
visite nuestro sitio web: http://shop.panasonic.com/support para clientes en
los EE. UU. (solo en inglés)
Por favor, registre su producto: http://shop.panasonic.com/support
PNQX6700XA CC0714WK2105 (E)
HNS102_(es_es)_1019_ver.210.pdf 1 2015/10/19 13:37:43
Configuración
Nombres de los componentes y
funciones .........................................3
Led indicador ...................................3
Resumen de configuración ..............3
Colocación de las baterías ..............4
Registro del sensor de
movimiento ......................................4
Información acerca de las
características del sensor ................5
Confirmación del área de uso ..........7
Montaje en la pared .........................8
Apéndice
Prueba del sensor de
movimiento ....................................10
Ajuste de sensibilidad del
sensor ............................................10
Acceso a la Guía del usuario .........10
2
Tabla de Contenido
HNS102_(es_es)_1019_ver.210.pdf 2 2015/10/19 13:37:43
Nombres de los
componentes y
funciones
A
B
C
D
E
Sensor infrarrojo
Led indicador
MHIGHN/MLOWN
Se usa para cambiar la sensibilidad
del sensor (página 10).
Tapa posterior
M N
Se usa para confirmar el estado del
sensor o para registrar el sensor en el
hub.
Led indicador
Puede oprimir M
N y verificar el Led
indicador para confirmar el estado del
sensor.
Indicador Estado
Verde, en-
cendido
No se detectó movimiento
Rojo, encen-
dido
Se detectó movimiento
Rojo, parpa-
deante
El sensor está fuera de al-
cance del hub
Verde, par-
padeando
lentamente
Modo de registro (Opri-
mió y mantuvo oprimido
M
N)
Apagado Sin batería
Nota:
R El Led indicador no indica el estado del
sensor si el sensor no se ha registrado
(página 10).
Resumen de
configuración
1 Configuración inicial
Asegúrese de poder acceder al
sistema mediante su dispositivo móvil.
Para obtener más detalles, consulte la
Guía de configuración del sistema que
viene con su hub.
2 Inserte las baterías
El sensor de movimiento usa batería.
3 Registro
Solo se requiere si se compró el
sensor de movimiento por separado
(es decir, no como parte de un
paquete).
4 Confirme el área de insta
lación
Lea la información de este documento
para confirmar que el área de
instalación deseada sea la adecuada
para el correcto funcionamiento.
Para obtener ayuda, visite http://shop.panasonic.com/support
3
Configuración
HNS102_(es_es)_1019_ver.210.pdf 3 2015/10/19 13:37:43
5 Instalación
Instale el sensor de movimiento en la
ubicación deseada.
Colocación de las
baterías
R SOLO USE baterías alcalinas AA (LR6).
R NO use baterías de manganeso/Ni-Cd/
Ni-MH.
R Verifique las polaridades (
, ).
1 Extraiga la tapa posterior ejerciendo
presión sobre los lados superiores de
la misma (A) y deslícela hacia abajo
(B).
A
B
2 Inserte las baterías.
3 Coloque la tapa posterior.
R Colóquela con la marca “
”
hacia arriba y deslícela.
Registro del sensor de
movimiento
Este procedimiento no es necesario para
unidades que son parte de un paquete.
Antes de que pueda usar el sensor de
movimiento, se debe registrar en el hub.
Si compró los dispositivos por separado (es
decir, no como parte de un paquete), debe
registrar cada dispositivo en el hub.
Puede registrar cada unidad mediante los
botones de registro o la aplicación [Home
Network].
4
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS102_(es_es)_1019_ver.210.pdf 4 2015/10/19 13:37:43
Uso de los botones de registro
1 Hub:
Oprima y mantenga oprimido M
OTHER DEVICEN hasta que el Led
indicador parpadee lentamente en
verde.
2 Sensor de movimiento:
Oprima y mantenga oprimido M
N
hasta que el Led indicador parpadee
lentamente en verde (página 3).
R Cuando se ha completado el
registro, el hub emitirá un pitido
largo.
Nota:
R Para cancelar sin registrar el sensor,
oprima M N en el hub y en el sensor
nuevamente.
R Si el registro falla, el hub emitirá varios
pitidos cortos.
Uso de la aplicación
Cuando registra el sensor de movimiento al
usar la aplicación [Home Network], puede
asignarle un nombre a sus dispositivos y
agruparlos por ubicación. Para obtener más
información, consulte la Guía del usuario
(página 10).
Información acerca de
las características del
sensor
El sensor de movimiento usa un sensor
infrarrojo (es decir, sensor de calor).
Lea la información siguiente antes de
decidir dónde instalar el sensor de
movimiento.
Nota:
R Las características del sensor de
movimiento no están diseñadas para su
utilización en situaciones que requieran
alta confiabilidad. No recomendamos el
uso de las características del sensor de
movimiento en esas situaciones.
R Panasonic no asume ninguna
responsabilidad por lesiones o daños
provocados por el uso del sensor de
movimiento.
Uso del calor para detectar
movimiento
El sensor infrarrojo del sensor de
movimiento puede detectar el movimiento
al reconocer las diferencias de temperatura
que ocurran dentro del alcance del sensor.
Para ello detecta los rayos infrarrojos que
las personas, animales, etc., emiten de
forma natural, los cuales están
correlacionados a la temperatura del objeto.
El alcance de detección se indica en la
imagen me
diante la zona gris situada frente
al sensor de movimiento.
Alcance de detección con vista desde
arriba
1
1
Alcance de detección horizontal:
aprox. 90°
Para obtener ayuda, visite http://shop.panasonic.com/support
5
Configuración
HNS102_(es_es)_1019_ver.210.pdf 5 2015/10/19 13:37:43
Alcance de detección con vista lateral
1
2
1
Alcance de detección vertical:
aprox. 20°
2
Distancia de movimiento detectable:
aprox. 5 m (16.4 pies)
Nota:
R La detección se dificulta cuando hay
poca diferencia entre las temperaturas
de los objetos y el entorno, como en
verano. Por ende, la detección se facilita
cuando hay mucha diferencia entre las
temperaturas de los objetos y el entorno,
como en invierno o de noche.
R La detección no es posible cuando hay
obstáculos frente al sensor infrarrojo.
Qu
ite los obstáculos o cambie la
ubicación de instalación.
Dirección del movimiento
Es más fácil detectar objetos que se
mueven de lado frente al sensor de
movimiento y más difícil detectar objetos
que se mueven de frente hacia el sensor de
movimiento.
D
A
B
C
Es difícil detectar movimiento
directamente frontal hacia el sensor de
movimiento.
Es fácil detectar movimiento lateral
frente al sensor de movimiento.
Alcance de detección
Sensor de movimiento
6
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS102_(es_es)_1019_ver.210.pdf 6 2015/10/19 13:37:43
Confirmación del área
de uso
Alcance de la comunicación
inalámbrica
El alcance de la comunicación inalámbrica
de cada dispositivo en el sistema del hub
es de aproximadamente 50 m (160 pies) en
interiores y de aproximadamente 300 m
(1,000 pies) en el exterior. Es posible que la
comunicación inalámbrica no sea tan
confiable cuando se encuentran los
obstáculos siguientes entre el hub y otros
dispositivos.
R Puertas o pantallas metálicas
R Par
edes que contengan aislamiento de
aluminio
R Paredes de hormigón o hierro corrugado
R Ventanas de vidrio doble
R Varias paredes
R Cuando los dispositivos están en pisos o
edificios diferentes
Nota:
R Puede verificar el estado de la
comunicación del sensor de movimiento
presionando M
N. Si el Led indicador
está iluminado en verde o rojo, el sensor
se está comunicando de forma
adecuada con el hub. Si el Led indicador
parpadea en rojo, se encuentra fuera de
alcance del hub.
Precauciones respecto al área
de uso
Usar el sensor de movimiento en las áreas
siguientes puede causar deformación,
averías o fallas de operación.
R A la luz del sol
R En áreas expuestas a grasa o vapor,
como en cocinas
R Cerca del fuego o calefactores
R Cerca de campos magnéticos (como
cerca de hornos microondas e imanes)
R Áreas sujetas a cambios extremos de
temperatura, como cerca de aires
acondicionados
R Áreas con objetos reflectivos, como
vidrios, que pueden interferir con la
detección de la variación de temperatura
R Áreas donde objetos de iluminación
afectan la temperatura (como luces
fluorescentes)
R Cerca de dispositivos que emiten ondas
de radio potentes, como teléfonos
móviles
Para obtener ayuda, visite http://shop.panasonic.com/support
7
Configuración
HNS102_(es_es)_1019_ver.210.pdf 7 2015/10/19 13:37:43
Montaje en la pared
Hay dos métodos para instalar el sensor de
movimiento en la pared. Para montar el
sensor contra la pared, utilice la tapa
posterior. Para montar el sensor y éste gire
45° a la derecha o a la izquierda, utilice el
adaptador de instalación en pared.
Ejemplos de instalación
*1
de la tapa
posterior y del adaptador de instala-
ción en pared
1
A Tapa posterior
2
B Adaptador de ins-
talación en pared
*1 Vista desde arriba.
Nota:
R Monte el sensor de movimiento en una
ubicación estable donde el este se
pueda colocar con seguridad.
R No coloque el sensor de movimiento
sobre un material blando. Podría caerse,
romperse o provocar lesiones.
R No monte el sensor de movimiento en
las ubicaciones siguientes: tablas de
yeso, hormigón celular, bloques de
hormigón, contrachapados con grosor
inferior a 25.4 mm (1 pulgada
), etc.
Uso de la tapa posterior
1 Extraiga la tapa posterior ejerciendo
presión sobre los lados superiores de
la misma (A) y deslícela hacia abajo
(B).
A
B
2 Instale la tapa posterior en la pared
con tornillos (
1
).
R Coloque la tapa posterior con la
marca “UP” hacia arriba.
R
2
37 mm (1 15/32 pulgadas)
U
P
2
1
UP
1
8
Para obtener ayuda, visite http://shop.panasonic.com/support
Configuración
HNS102_(es_es)_1019_ver.210.pdf 8 2015/10/19 13:37:43
3 Coloque el sensor de movimiento en
la tapa posterior.
R Inserte las 4 lengüetas de la tapa
posterior en los canales del sensor
de movimiento y luego ejerza
presión hacia abajo sobre el sensor
de movimiento.
U
P
Uso del adaptador de instalación en
pared
1 Extraiga la tapa posterior ejerciendo
presión sobre los lados superiores de
la misma (A) y deslícela hacia abajo
(B).
A
B
2 Instale el adaptador de instalación en
pared con tornillos (
1
).
R Coloque el adaptador de
instalación en pared con la marca
“UP” hacia arriba.
R
2
21 mm (27/32 pulgadas)
2
UP
1
1
3 Coloque el sensor de movimiento en
el adaptador de instalación en pared.
R Inserte las 4 lengüetas del
adaptador de instalación en pared
en los canales del sensor de
movimiento y luego ejerza presión
hacia abajo sobre el sensor de
movimiento.
Para obtener ayuda, visite http://shop.panasonic.com/support
9
Configuración
HNS102_(es_es)_1019_ver.210.pdf 9 2015/10/19 13:37:43
Prueba del sensor de
movimiento
Puede observar el Led indicador del sensor
de movimiento y probar el funcionamiento
del sensor de movimiento.
1 Oprima M
N.
2 Muévase a un área cerca del sensor
de movimiento.
3 A medida que se acerque al sensor de
movimiento, observe el Led indicador.
R Cuando se detecta movimiento, el
Led indicador se ilumina en rojo.
4 Observe las áreas donde se detecta el
movimiento.
5 Presione M
N de nuevo.
Ajuste de sensibilidad
del sensor
Puede usar el interruptor MHIGHN/MLOWN
(página 3) para ajustar la sensibilidad del
sensor. Si el sensor tiende a hacer
detecciones falsas, como en áreas con
fluctuaciones de temperatura frecuentes y
considerables, coloque el interruptor en la
posición MLOWN.
Nota:
R Cuando el interruptor está en la posición
MLOWN, se reduce el alcance de
detección a casi la mitad (en
comparació
n a cuando el interruptor
está en la posición MHIGHN).
Acceso a la Guía del
usuario
La Guía del usuario es una colección de
documentación en línea que lo ayuda a
aprovechar al máximo la aplicación [Home
Network].
1 iPhone
®
/iPad
®
Toque
en la pantalla de inicio de
la aplicación.
Dispositivos Android™
Toque
u oprima el botón menú de
su dispositivo en la pantalla de inicio
de la aplicación.
2 Toque [Guía del Usuario].
Nota:
R No se admite Microsoft
®
Windows
®
Internet Explorer
®
8 y versiones
anteriores.
R Se recomienda Android 4.1 y versiones
posteriores.
R También puede acceder a la Guía del
usuario mediante la página web a
continuación.
www.panasonic.net/pcc/support/tel/
homenetwork/manual/
10
Para obtener ayuda, visite http://shop.panasonic.com/support
Apéndice
HNS102_(es_es)_1019_ver.210.pdf 10 2015/10/19 13:37:43
11
Notas
HNS102_(es_es)_1019_ver.210.pdf 11 2015/10/19 13:37:44
12
Notas
HNS102_(es_es)_1019_ver.210.pdf 12 2015/10/19 13:37:44
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Panasonic KXHN6092 Instrucciones de operación
- Tipo
- Instrucciones de operación
En otros idiomas
Documentos relacionados
-
Panasonic KXHNS102 Instrucciones de operación
-
-
-
-
-
-
Panasonic KXHN6006SK Instrucciones de operación
-
Panasonic KXHN6002 Instrucciones de operación
-
-