Radiant radiant 120V Single Pole Occupancy Sensor Guía de instalación

Marca: Radiant

Modelo: radiant 120V Single Pole Occupancy Sensor

Tipo: Guía de instalación

No: 341168– 03/16

Pass & Seymour

Occupancy/Vacancy Sensor Switch

Interrupteur à détection de présence/Interrupteur détecteur d’inoccupation

Interruptor de sensibilidad a la ocupación/Interruptor con sensor de “habitación vacía”

Incandescent/ELV: 600W ; CFL/LED: 450W; MLV: 600VA; ELV: 5A; Motor: 1/6 hp

Installation Instructions • Notice d’Installation • Instrucciones de Instalación

Catalog Number(s) • Numéro(s) de Catalogue • Les Numéros de Catalogue: RRW600U

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

DESCRIPTION AND OPERATION

The RRW600U occupancy and vacancy sensor is designed to replace a

standard light or fan switch. The sensor uses passive infrared technology

to sense human motion in a space and turn the light OFF when the room

is vacant. It is ideal for applications in a home where there is a direct line

of sight from the sensor to the room, including bedrooms and family/living

rooms.

Occupancy Mode:

The load will automatically come ON when motion is detected, and turn

OFF automatically, at the desired time delay, if no motion is detected. If the

load is manually turned OFF, and motion is detected within 30 seconds,

the load will remain OFF until no motion has been detected for 30 seconds.

It can then automatically turn ON again once it detects motion. The

RRW600U allows the load to be turned ON manually as well, and turn OFF

automatically at the desired time delay, if no motion is detected.

Vacancy Mode:

In this mode, the load is required to be turned ON manually, and will

turn OFF at the desired time delay, if no motion is detected. If motion is

detected within 30 seconds after it automatically turns OFF, the RRW600U

automatically turns the load back ON.

USER SETTINGS

Table 1 – Time Delay Setting

Setting Status From User

(Input to the device)

LED or LOAD State

(Acknowledgement

from the device)

Result

Time Delay

Adjustment

Mode – To

change the

amount of time

before the

sensor switch

turns off after

last movement

Initiate

With the load ON or OFF,

hold down the ON/OFF

button for 10 seconds

then release

LED will blink 5 times

and then turn off

Enters

Time Delay

Adjustment Mode

Activate

Push down the ON/ OFF

button rst time.

LED ashes quickly two

times per 1.5s.

Set the time delay to

5 Minutes

Push down the ON/ OFF

button second time

LED ashes quickly

three times per 1.5s.

Set the time delay to

10 Minutes

Push down the ON/ OFF

button third time

LED ashes quickly four

times per 1.5s.

Set the time delay to

15 Minutes

Push down the ON/ OFF

button fourth time

LED ashes quickly ve

times ON per 1.5s.

Set the time delay to

30 Minutes

Push down the ON/ OFF

button fth time

LED ashes quickly one

time per 1.5s.

Set the time delay

to 30 Seconds

Save/ Exit

Hold down the ON/ OFF

button for 10 seconds

then release

LED will blink 5 times

and then turn off

Save/ Exit Time

Delay Adjustment

Mode

Table 2 – RRW600U Occupancy/Vacancy Mode Adjustment

Setting Status

From User

(Input to the device)

LED or LOAD State

(Acknow ledgement

from the device)

Result

Working Mode

Setting: to

Change between

Occupancy Mode

(Auto on) and

Vacancy Mode

(Manual On)

Initiate With the load ON or OFF,

hold down the ON/OFF

button for 15 seconds

then release

LED will blink 5 times

and then turn off

Enters

Working Mode

Setting Mode

Activate Push down the ON/ OFF

button rst time

LED ashes quickly

two times ON per 1s.

Set the Working

Mode to vacancy

sensor

Push down the ON/ OFF

button second time

LED ashes quickly

one time ON per 1s.

Set the

Working Mode

to occupancy

sensor

Save/ Exit Hold down the ON/ OFF

button for 15 seconds

then release

LED will blink 5 times

and then turn off

Save/ Exit

Working Mode

Setting Mode

The RRW600U has an onboard indicator LED located at the top of the unit This

indicator is used to show when motion is detected. The LED is also used while

programming the RRW600U and indicates STATUS during power up. The LED

is further used to indicate a malfunctioning unit. Both Occupancy and Vacancy

Modes can be programmed/selected to function with or without the LED

indicator if preferred by the user.

Table 3 – Status LED Enable/DIsable

Setting Status

From User (Input to

the device)

LED or LOAD State

(Acknow ledgement

from the device)

Result

Enable and

disable the

status LED

indicator

When the

LED is

Enabled

With the load ON or

OFF, hold down the

ON/ OFF button for

25 seconds

LED will blink 5 times

and then turn off

LED will Disable: locator light

will be in an “On State” when

the load is off and will not blink

when motion is detected; the

locator light will be in an “Off

State” when the load is on and

will not blink when motion is

detected

When the

LED is

Disabled

With the load ON or

OFF, hold down the

ON/ OFF button for

25 seconds

LED will blink 5 times

and then turn off

LED will Enable: locator light

will be in an “On State” when

the load is off and will not blink

when motion is detected; the

locator light will be in an “Off

State” when the load is on

and will blink when motion is

detected.

COVERAGE AREA

The RRW600U has a maximum

coverage range of 180 degrees

and a coverage area of 600 square

feet (56 square meters). The sensor

must have a clear and unobstructed

view of the coverage area. Objects

blocking the sensor’s lens may

prevent detection thereby causing

the light to turn off even though

someone is in the area.

Windows, glass doors, and other

transparent barriers will obstruct

the sensor’s view and prevent

detection.

INSTALLATION & WIRING

1. Prepare the switch box.

After the power is turned off at the circuit breaker box, remove the existing wall

plate and mounting screws. Pull the old switch out from the wall box.

2. Identify the type of circuit.

Single Pole

In a Single Pole Circuit (see Figure

2), two single wires connect to two

screws on the existing switch. A

ground wire may also be present

and connected to a ground terminal

on the old switch.

3-Way

In a 3-way circuit (see Figure 3),

there will be [2 runners and

1 common] for both switches

involved.

CAUTION For your safety: Connecting a proper ground to the sensor provides

protection against electrical shock in the event of certain fault conditions. If

a proper ground is not available, consult with a qualified electrician before

continuing installation.

3. Prepare the Wires.

Tag the wires currently connected to

the existing switch, so that they can be

identified later. Disconnect the wires. Make

sure the insulation is stripped off the wires

to expose their copper cores to the length

indicated by the “Strip Gage,” in Figure 3a.

4. Wire the sensor.

1-pole configuration:

Twist existing wires together

with the wire leads on the

RRW600U sensor as indicated

below. Cap them securely

using the wire nuts provided.

See Figure 4.

• Connect the green or non-

insulated (copper) GROUND

wire from the circuit to the

green ground wire on the

RRW600U. Make sure there

is a solid ground connection.

• Connect the power wire

from the circuit (HOT)

to the black wire on the

RRW600U.

• Connect the power wire to

the lamp or fan (LOAD) to the red wire on the RRW600U.

Multilocation configuration (using existing companion 3-way switch):

see Figure 5.

• Connect the green or non-insulated (copper) GROUND wire from the circuit

to the green ground wire on the RRW600U. Make sure there is a solid

ground connection.

• Connect the power wire from the circuit (HOT) to the black wire on

the RRW600U.

• Connect the power wire to the lamp or fan (LOAD) to the red wire on

the RRW600U.

• Connect one of the runner wires to the yellow wire of the RRW600U.

• For the companion switch, connect the chosen runner wire (presently

hooked up to the yellow wire of the RRW600U) to the common of the 3-way

companion mechanical switch.

• Connect one of the poles of the companion 3-way switch to ground.

• For the remaining pole of the companion 3-way switch, do not connect to

anything, but still cap off with a wire nut.

common

commun

común

H1 NC

Line

Ligne

Linea

Black

Noir

Negro

Yellow

Jaune

Amarillo

Green

Vert

Verde

Red

Rouge

Rojo

Load

Charge

Carga

Ground

Terre

Tierra

Neutral

Neutre

Neutro

Figure 5: 3-Way Conguration / Figure 5 : Conguration à 3 voies

Figura 5: Conguración de 3 vías

Multilocation configuration (using up to 5 units, maximum wire length of

100 ft between companion unit and unit connected to the load):

see Figure 6.

• Connect the green or non-insulated (copper) GROUND wire from the circuit

to the green ground wire on the RRW600U. Make sure there is a solid

ground connection.

• Connect the power wire from the circuit (HOT) to the black wire on

the RRW600U.

• Connect the power wire to the lamp or fan (LOAD) to the red wire on

the RRW600U.

• Connect one of the runner wires to the yellow wire of the RRW600U.

• For the companion RRW600U, connect the chosen runner wire (presently

hooked up to the yellow wire of the 1st RRW600U) to the yellow wire of the

companion RRW600U.

• Repeat for additional RRW600U units.

5. Put the RRW600U in the wall box. Position the lens above the ON/OFF

button (lens at top, button at bottom). Secure it to the wall box with the

screws provided.

6. Make any necessary adjustments. See the SENSOR ADJUSTMENT section

for information.

7. Attach the new cover plate.

8. Restore power to the circuit. Turn on the breaker or replace the fuse.

INITIAL POWER UP DELAY

There is an initial warm-up (about 1 minute) and calibration period the first

time power is applied to the unit and after the load is replaced. The warm-up

sequence also occurs as a result of a power failure, and any time power to the

unit is cycled.

CHANGING THE COLOR OF THE UNIT

1. Remove the wallplate.

2. Firmly grasp the edges of

the front cover directly below

the lens where it says “open.”

Push in one side first until it

pops out, then the other side.

Remove front cover from the unit

(see Figure 7).

3. Take the new color front cover,

place the top peg in first then

snap in each side one at a

time (see Figure 9).

TROUBLESHOOTING

Status LED is enabled but not blinking and the load will not turn ON:

• Check the circuit breaker to be sure it is functioning.

• Check to make sure that the device is properly grounded. This device will not

function if it is not grounded.

Load will not turn ON:

Press ON/OFF button. The load should turn ON. If not:

• Check the light bulb and/or motor switch on the fan mechanism.

• Turn OFF power to the circuit then check wire connections.

• For further assistance call 800.223.4185 for technical support.

Load will not turn OFF:

Note: The time delay can be set from 30 seconds to 30 minutes. Ensure that

the time delay is set to the desired delay and that there is no movement within

the sensor’s view for that time period.

• To quickly test the unit for proper operation, turn the time delay to minimum

and move out of the sensor’s view. Lights should turn off after 30 seconds.

• Press the ON/OFF button. If load does not turn off, turn off power to the

circuit then check wire connections.

• For further assistance call 800.223.4185 for technical support.

25'

(7.6m)

12'

(3.7m)

Figure 1: Sensor Coverage Area

Figure 1 : Zone de portée du détecteur

Figura 1: Área de cobertura del sensor

Figure 3: 3-Way

Figure 3: Trois voies

Figura 3: 3 Vías

READ AND SAVE THESE INSTRUCTIONS

To be installed by a certified electrician or other qualified person.

WARNING – To prevent severe shock or electrocution, always turn

poweroff at the service panel before installing this product, working on the

circuit, or changing a lamp.

CAUTION

• Do not connect this product to a power source other than 120VAC,

60Hz.

• Use copper wire only.

Specifications

Load..........................................Single Pole or 3 Way

Time Delay ...............................30 Seconds to 30 Minutes

Environment .............................Indoor Use Only

Tools Needed

Insulated Screwdriver, Wire Strippers

LIRE ET CONSERVER CES INSTRUCTIONS

Doit être installé par un électricien certifié ou une autre personne qualifiée.

AVERTISSEMENT – Pour éviter tout choc électrique ou une électrocution,

toujours couper l’électricité au niveau du panneau d’alimentation avant

d’installer cette unité, de travailler sur le circuit électrique ou de changer

une lampe.

AVERTISSEMENT

• Ne brancher ce produit qu’à une source d’alimentation de 120 V c.a.,

60 Hz.

• N’utiliser que des fils en cuivre.

Spécifications

Charge ......................................Unipolaire ou à 3 voies

Temporisation ...........................30 secondes à 30 minutes

Environnement .........................Utilisation en intérieur uniquement

Outils nécessaires

Tournevis isolé, dénudeurs de fil

LEA Y CONSERVE ESTAS INSTRUCCIONES

Para ser instalado por un electricista certificado o persona competente.

ADVERTENCIA – Para evitar descargas eléctricas serias o electrocución,

antes de instalar, trabajar en el circuito o cambiar una lámpara de este

atenuador apague siempre el suministro eléctrico en el panel de servicio.

PRECAUCIÓN

• No conecte este producto a una fuente de alimentación que no sea de

120 V AC, 60Hz.

• Use solamente cables de cobre.

Especificaciones

Carga ........................................Polo único o de 3 vías

Tiempo de demora ...................30 segundos a 30 minutos

Entorno ..................................... Solo uso en interiores

Herramientas necesarias

Destornillador aislado, pelacables

Figure 6: Multilocation Conguration

Figure 6 : Conguration à plusieurs emplacements

Figura 6: Conguración de ubicación múltiple

Black

Noir

Negro

Yellow / Jaune / Amarillo

Green

Vert

Verde

Ground

Terre

Tierra

Line

Ligne

Linea

Load

Charge

Carga

Line

Ligne

Linea

Red

Rouge

Rojo

Neutral

Neutre

Neutro

Line

Ligne

Linea

Black

Noir

Negro

Green

Vert

Verde

Ground

Terre

Tierra

Red

Rouge

Rojo

Time

Delay

Motion Blink

OFF

30se

c.30min.

5min.

10mi

20mi

11543r1

Figure 9: Replace Front Cover

Figure 9 : Remplacement de

la protection avant

Figura 9: Reemplace la cubierta frontal

RRW600U

Figure 2:

Single Pole

Figure 2: Pôle simple

Figura 2: Polo único

Line

Ligne

Linea

Black / Noir / Negro

Yellow / Jaune / Amarillo

Green / Vert / Verde

Red

Rouge

Rojo

Load

Charge

Carga

Ground

Terre

Tierra

Neutral

Neutre

Neutro

Figure 4: Single Pole Conguration

Figure 4 : Conguration unipolaire

Figura 4: Conguración del polo único

3-Way

In a 3-Way circuit, identify the Common/

Hot wire – connected to the terminal

marked Common or the odd-colored

terminal screw.

Trois voies (3-Way)

Pour un circuit à trois voies, identifier le

câble de commun/courant raccordé à la

borne marquée « Commun » ou à la vis

de borne de couleur différente.

3 vías

En un circuito de 3 vías, identifique el

cable Común/Vivo: conectado al terminal

marcado como Común o al tornillo del

terminal de color diferente.

Strip Gage

1/2"

12.7mm

Figure 3a: Wire Stripping

Figure 3a : Dénudage des ls

Figura 3a: Pelado de cables

Strip Gauge,

Borne à vis

Traseros para cables

1/2"

12.7mm

341168_RRW600U OccVac Sensor IS.indd 1 3/8/16 8:25 AM

860.233.6251

1.877.BY.LEGRAND

www.legrand.us

www.legrand.ca

No: 341168 – 03/16

WARRANTY INFORMATION

Pass & Seymour/Legrand warranties its products to be free of defects in materials and

workmanship for a period of five (5) years. There are no obligations or liabilities on the part of

Pass & Seymour/Legrand for consequential damages arising out of, or in connection with, the

use or performance of this product or other indirect damages with respect to loss of property,

revenue or profit, or cost of removal, installation or reinstallation.

INFORMATIONS DE GARANTIE

Pass & Seymour/Legrand garantit ses produits de tout défaut de matériaux et de main

d’œuvre pour une période de cinq (5) ans. Aucune obligation ou responsabilité n’incombe à

Pass & Seymour/Legrand en cas de dommage par découlant de ou lié à l’utilisation ou aux

performances de ce produit ou de tout autre dommage indirect lié à la perte de biens, la perte

de revenus, tout manque à gagner ou tout coût de retrait, d’installation ou de réinstallation.

INFORMACIÓN SOBRE LA GARANTÍA

Pass & Seymour/Legrand garantiza que sus productos están libres de defectos en

materiales y mano de obra por un período de cinco (5) años. No existen obligaciones ni

responsabilidades por parte de Pass & Seymour/Legrand por daños consecuentes que deriven

o estén relacionados con el uso o rendimiento de este producto u otros daños indirectos con

respecto a la pérdida de propiedad, renta o ganancias, o al costo de extracción, instalación o

reinstalación.

INSTRUCCIONES EN ESPAÑOLINSTRUCTIONS EN FRANÇAIS

Tableau 1 – Réglage du délai de temporisation

Réglage État Par l’utilisateur

(Entrée des données dans l’appareil)

DEL ou état de CHARGE

(Conrmation de l’appareil)

Résultat

Mode de réglage du

délai de temporisation –

Pour modier le temps

qui doit s’écouler avant

que le contacteur de

détection s’éteigne

après le dernier

mouvement

Début

Avec la charge EN COURS ou COMPLÈTE,

maintenez le bouton ON/OFFappuyé pendant

10 secondes puis relâchez-le

La DEL clignotera 5 fois et s’éteindra Entrez en mode de réglage du

délai de temporisation

Activation

Appuyez sur le bouton ON/OFF une première fois. La DEL clignotera rapidement deux fois

pendant 1,5 seconde