Pentair 340039 Guía del usuario

Marca: Pentair

Modelo: 340039

Categoría: Accesorios para piscinas elevadas

Tipo: Guía del usuario

SUPERFLO®

HIGH PERFORMANCE PUMP

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

INSTALLATION AND

USER’S GUIDE

SUPERFLO® High Performance Pump Installation and User’s Guide

TABLE OF CONTENTS

Important Pump Warning and

Safety Instructions ..............................................

Pump Overview ....................................................

Pump Overview

General Features

Installation ...........................................................

Location

Piping

Fittings and Valves

Electrical Wiring Installation

Maintenance .........................................................

Pump Strainer Basket

Cleaning the Pump Strainer Basket

Winterizing

Servicing ..............................................................

If you have questions about ordering Pentair Aquatic Systems replacement parts, and pool products, please contact:

CUSTOMER SERVICE / TECHNICAL SUPPORT

Customer Service and Technical Support, USA

(8 A.M. to 4:30 P.M. — Eastern/Paciﬁc Times)

Phone: (800) 831-7133

Fax: (800) 284-4151

Web site

Visit www.pentairpool.com to ﬁnd more information

about Pentair products.*

Sanford, North Carolina (8 A.M. to 4:30 P.M. ET)

Phone: (919) 566-8000

Fax: (919) 566-8920

Moorpark, California (8 A.M. to 4:30 P.M. PT)

Phone: (805) 553-5000 (Ext. 5591)

Fax: (805) 553-5515

Electric Motor Care

Shaft Seal Replacement

Pump Disassembly

Pump Reassembly

Restart Instructions

Priming the Pump

Troubleshooting ..................................................

Replacement Parts .............................................

Technical Data .....................................................

P/N 350096 Rev. G 1/19/16

* Translated versions of this manual are available online at / La versión en español de este manual del producto, se puede encontrar en

línea a

: http://www.pentairpool.com/products/pumps-inground-superﬂo-high-performance-pumps-165.htm.

SUPERFLO® High Performance Pump Installation and User’s Guide

IMPORTANT PUMP WARNING AND SAFETY INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, include the following:

Do not permit children to use this product.

RISK OF ELECTRICAL SHOCK. Connect only to

a branch circuit protected by a ground-fault circuit-

interrupter (GFCI). Contact a qualiﬁed electrician if you cannot verify that

the circuit is protected by a GFCI.

This unit must be connected only to a supply circuit

that is protected by a ground-fault circuit-interrupter

(GFCI). Such a GFCI should be provided by the installer and should

be tested on a routine basis. To test the GFCI, push the test button.

The GFCI should interrupt power. Push the reset button. Power should

be restored. If the GFCI fails to operate in this manner, the GFCI is

defective. If the GFCI interrupts power to the pump without the test button

being pushed, a ground current is ﬂowing, indicating the possibility of an

electric shock. Do not use this pump. Disconnect the pump and have the

problem corrected by a qualiﬁed service representative before using.

This pump is for use with permanent swimming

pools and may also be used with hot tubs and spas if

so marked. Do not use with storable pools. A permanently-installed pool

is constructed in or on the ground or in a building such that it cannot be

readily disassembled for storage. A storable pool is constructed so that

it is capable of being readily disassembled for storage and reassembled

to its original integrity.

General Warnings

• Never open the inside of the drive motor enclosure. There is a

capacitor bank that holds a 230 VAC charge even when there is no

power to the unit.

• The pump is not submersible.

• The pump is capable of high ﬂow rates; use caution when installing

and programming to limit pumps performance potential with old or

questionable equipment.

• Code requirements for electrical connection differ from country to

country, state to state, as well as local municipalities. Install equipment

in accordance with the National Electrical Code and all applicable

local codes and ordinances.

• Before servicing the pump; switch OFF power to the pump by

disconnecting the main circuit to the pump.

• This appliance is not intended for use by persons (including children) of

reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning the use of the appliance by a person responsible for their

safety.

FAILURE TO FOLLOW ALL INSTRUCTIONS AND

WARNINGS CAN RESULT IN SERIOUS BODILY

INJURY OR DEATH. THIS PUMP SHOULD BE INSTALLED AND

SERVICED ONLY BY A QUALIFIED POOL SERVICE PROFESSIONAL.

INSTALLERS, POOL OPERATORS AND OWNERS MUST READ THESE

WARNINGS AND ALL INSTRUCTIONS IN THE OWNER’S MANUAL

BEFORE USING THIS PUMP. THESE WARNINGS AND THE OWNER’S

MANUAL MUST BE LEFT WITH THE POOL OWNER.

SUCTION ENTRAPMENT HAZARD: STAY OFF

THE MAIN DRAIN AND AWAY FROM ALL SUCTION

OUTLETS!

THE USE OF UNAPPROVED COVERS OR ALLOWING USE OF

THE POOL OR SPA WHEN COVERS ARE MISSING, CRACKED OR

BROKEN CAN RESULT IN BODY OR LIMB ENTRAPMENT, HAIR

ENTANGLEMENT, BODY ENTRAPMENT, EVISCERATION AND/OR

DEATH.

The suction at a drain or outlet can cause:

Limb Entrapment: When a limb is sucked or inserted into an opening

resulting in a mechanical bind or swelling. This hazard is present when

a drain cover is missing, broken, loose, cracked or not properly secured.

Hair Entanglement: When the hair tangles or knots in the drain cover,

trapping the swimmer underwater. This hazard is present when the ﬂow

rating of the cover is too small for the pump or pumps.

Body Entrapment: When a portion of the body is held against the drain

cover trapping the swimmer underwater. This hazard is present when the

drain cover is missing, broken or the cover ﬂow rating is not high enough

for the pump or pumps.

Evisceration/Disembowelment: When a person sits on an open pool

(particularly a child wading pool) or spa outlet and suction is applied directly

to the intestines, causing severe intestinal damage. This hazard is present

when the drain cover is missing, loose, cracked, or not properly secured.

THIS PUMP PRODUCES HIGH LEVELS OF SUCTION AND CREATES

A STRONG VACUUM AT THE MAIN DRAIN AT THE BOTTOM OF THE

BODY OF WATER. THIS SUCTION IS SO STRONG THAT IT CAN TRAP

ADULTS OR CHILDREN UNDER WATER IF THEY COME IN CLOSE

PROXIMITY TO A DRAIN OR A LOOSE OR BROKEN DRAIN COVER

OR GRATE.

This guide provides installation and operation instructions for this pump.

Consult Pentair with any questions regarding this equipment.

Attention Installer: This guide contains important information about the

installation, operation and safe use of this product. This information should

be given to the owner and/or operator of this equipment after installation

or left on or near the pump.

Attention User: This manual contains important information that will help

you in operating and maintaining this product. Please retain it for future

reference.

This is the safety alert symbol. When you see this

symbol on your system or in this manual, look for

one of the following signal words and be alert to

the potential for personal injury.

Warns about hazards that can cause death,

serious personal injury, or major property damage

if ignored.

Warns about hazards that may cause death,

serious personal injury, or major property damage

if ignored.

Warns about hazards that may or can cause minor

personal injury or property damage

if ignored.

NOTE Indicates special instructions not related to

hazards.

Carefully read and follow all safety instructions in this manual and on

equipment. Keep safety labels in good condition; replace if missing

or damaged.

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

IMPORTANT NOTICE

SUPERFLO® High Performance Pump Installation and User’s Guide

iii

Warning Page P/N 352557 Rev. A 6/15

IMPORTANT PUMP WARNING AND SAFETY INSTRUCTIONS

For Installation of Electrical Controls at Equipment Pad (ON/OFF

Switches, Timers and Automation Load Center)

Install all electrical controls at equipment pad, such as

on/off switches, timers, and control systems, etc. to

allow the operation (startup, shut-down, or servicing)

of any pump or ﬁlter so the user does not place any

portion of his/her body over or near the pump strainer

lid, ﬁlter lid or valve closures. This installation should

allow the user enough space to stand clear of the

ﬁlter and pump during system start-up, shut down or

servicing of the system ﬁlter.

SAVE THESE INSTRUCTIONS

HAZARDOUS PRESSURE: STAND CLEAR OF

PUMP AND FILTER DURING START UP

Circulation systems operate under high pressure.

When any part of the circulating system (i.e.

locking ring, pump, ﬁlter, valves, etc.) is serviced,

air can enter the system and become pressurized.

Before servicing equipment, make note of the ﬁlter pressure. Be sure

that all controls are set to ensure the system cannot inadvertently start

during service. Turn off all power to the pump. IMPORTANT: Place ﬁlter

manual air relief valve in the open position and wait for all pressure

in the system to be relieved.

Before starting the system, fully open the manual air relief valve and place

all system valves in the “open” position to allow water to ﬂow freely from the

tank and back to the tank. Stand clear of all equipment and start the pump.

IMPORTANT: Do not close ﬁlter manual air relief valve until all

pressure has been discharged from the valve and a steady stream

of water appears. Observe ﬁlter pressure gauge and be sure it is not

higher than the pre-service condition.

Pressurized air can cause the pump housing cover, ﬁlter lid, and valves

to violently separate which can result in severe personal injury or death.

Filter tank lid and strainer cover must be properly secured to prevent

violent separation. Stand clear of all circulation system equipment when

turning on or starting up pump.

General Installation Information

• All work must be performed by a qualiﬁed service professional, and

must conform to all national, state, and local codes.

• Install to provide drainage of compartment for electrical components.

• These instructions contain information for a variety of pump models

and therefore some instructions may not apply to a speciﬁc model. All

models are intended for use in swimming pool applications. The pump

will function correctly only if it is properly sized to the speciﬁc application

and properly installed.

Pumps improperly sized or installed or used in

applications other than for which the pump was

intended can result in severe personal injury or death. These risks may

include but not be limited to electric shock, ﬁre, ﬂooding, suction

entrapment or severe injury or property damage caused by a structural

failure of the pump or other system component.

The pump can produce high levels of suction within

the suction side of the plumbing system. These high

levels of suction can pose a risk if a person comes within the close

proximity of the suction openings. A person can be seriously injured by

this high level of vacuum or may become trapped and drown. It is

absolutely critical that the suction plumbing be installed in accordance

with the latest national and local codes for swimming pools.

The Virginia Graeme Baker (VGB) Pool and Spa Safety Act creates

new requirements for owners and operators of commercial swimming

pools and spas.

Commercial pools or spas constructed on or after December 19, 2008,

shall utilize:

(A) A multiple main drain system without isolation capability with suction

outlet covers that meet ASME/ANSI A112.19.8a Suction Fittings for

Use in Swimming Pools, Wading Pools, Spas, and Hot Tubs and either:

(i) A safety vacuum release system (SVRS) meeting ASME/ANSI

A112.19.17 Manufactured Safety Vacuum Release systems (SVRS)

for Residential and Commercial Swimming Pool, Spa, Hot Tub,

and Wading Pool Suction Systems and/or ASTM F2387 Standard

Speciﬁcation for Manufactured Safety Vacuum Release Systems

(SVRS) for Swimming pools, Spas and Hot Tubs or

(ii) A properly designed and tested suction-limiting vent system or

(iii) An automatic pump shut-off system.

Commercial pools and spas constructed prior to December 19, 2008,

with a single submerged suction outlet shall use a suction outlet cover

that meets ASME/ANSI A112.19.8a and either:

(A) A SVRS meeting ASME/ANSI A112.19.17 and/or ASTM F2387, or

(B) A properly designed and tested suction-limiting vent system, or

(D) Disabled submerged outlets, or

(E) Suction outlets shall be reconﬁgured into return inlets.

A clearly labeled emergency shut-off switch for the

pump must be in an easily accessible, obvious place.

TO MINIMIZE THE RISK OF INJURY DUE TO

SUCTION ENTRAPMENT HAZARD:

• A properly installed and secured ANSI/ASME A112.19.8 approved

anti-entrapment suction cover must be used for each drain.

• Each suction cover must be installed at least three (3’) feet apart,

as measured from the nearest point to nearest point.

• Regularly inspect all covers for cracks, damage and advanced

weathering.

• If a cover becomes loose, cracked, damaged, broken or is missing,

replace with an appropriate certiﬁed cover.

• Replace drain covers as necessary. Drain covers deteriorate over

time due to exposure to sunlight and weather.

• Avoid getting hair, limbs or body in close proximity to any suction

cover, pool drain or outlet.

• Disable suction outlets or reconﬁgure into return inlets.

Mechanical Entrapment: When jewelry, swimsuit, hair decorations,

ﬁnger, toe or knuckle is caught in an opening of an outlet or drain cover.

This hazard is present when the drain cover is missing, broken, loose,

cracked, or not properly secured.

NOTE: ALL SUCTION PLUMBING MUST BE INSTALLED IN

ACCORDANCE WITH THE LATEST NATIONAL AND LOCAL CODES,

STANDARDS AND GUIDELINES.

Make sure users know where it is and how to use it in case of emergency.

Warnings and safety instructions for Pentair Aquatic Systems

pumps and other related products are available at:

http://www.pentairpool.com/pool-owner/safety-warnings/ or call

(800) 831-7133 for additional free copies of these instructions.

Please refer to http://www.pentairpool.com/pool-owner/

safetywarnings/ for warning and safety instructions related to the

this product.

SUPERFLO® High Performance Pump Installation and User’s GuideSUPERFLO® High Performance Pump Installation and User’s Guide

Pump Overview

The perfect choice for all types of pools, the SuperFlo®

High Performance Pump was speciﬁcally designed to be

your best choice for a variety of inground pools.

Thick walled body parts, a heavy duty 56 square ﬂange

motor, and highly engineered hydraulics make this rugged

and tested design perfect for any pool, spa, water feature,

or fountain.

All pumps from Pentair Aquatic Systems incorporate

innovative hydraulic engineering that has been reﬁned for

over 40 years. Compact, rugged, and easy to maintain,

the SuperFlo pump will deliver years of reliable service.

SuperFlo High Performance Pump

PUMP OVERVIEW

General Features

• Extremely quiet operation

• Unionized ﬁttings (1.5” and 2”) for simple

replacement

• Cam and Ramp™ Lid for easy cleaning and

maintenance

• Heavy-duty, high service factor 56 square

ﬂange motor for long life

• Integral volute and pot reduce hydraulic noise

• See-through lid permits easy inspection of

strainer basket

• 115 volt or 230 volt models available

• 1/2 HP to 2 1/2 HP conﬁgurations to

accommodate a wide range of applications

• Self-priming for quick, easy start-up

SUPERFLO® High Performance Pump Installation and User’s Guide

INSTALLATION

Location

Be sure the pump location meets the following

requirements:

Piping

1. For improved pool plumbing, it is recommended to

use a larger pipe size. When installing the inlet and

outlet ﬁttings (male adaptors), use thread sealant.

2. Piping on the suction side of the pump should be

the same or larger than the return line diameter.

3. Plumbing on the suction side of the pump should

be as short as possible.

4. For most installations Pentair recommends installing

a valve on both the pump suction and return lines

so that the pump can be isolated during routine

maintenance. However, we also recommend that

a valve, elbow or tee installed in the suction line

should be no closer to the front of the pump than

ﬁve (5) times the suction line diameter.

Example: A 2 inch pipe requires a 10 inch (25.4

cm) straight run in front of the suction inlet of the

pump. This will help the pump prime faster and last

longer.

Note: DO NOT install 90° elbows directly into the

pump inlet or outlet.

Fittings and Valves

1. Do not install 90° elbows directly into pump inlet.

2. Flooded suction systems should have gate valves

installed on suction and discharge pipes for

maintenance, however, the suction gate valve should

be no closer than ﬁve times the suction pipe diameter

as described in this section.

3. Use a check valve in the discharge line when using

this pump for any application where there is signiﬁcant

height to the plumbing after the pump.

4. Be sure to install check valves when plumbing in

parallel with another pump. This helps prevent reverse

rotation of the impeller and motor.

1. Install the pump as close to the pool or spa as

possible. To reduce friction loss and improve

efﬁciency, use short, direct suction piping returns.

2. Install a minimum of 5 feet (1.52 meters) from the

inside wall of the pool and spa. Canadian installations

require a minimum of 9.8 feet (3 meters) from pool

water level.

3. Install the pump a minimum of 3 feet (.9 meters)

from the heater outlet.

4. Do not install the pump more than 10 feet (3 meters)

above the water level.

5. Install the pump in a well ventilated location

protected from excessive moisture (i.e., rain gutter

downspouts, sprinklers, etc.)

6. Install the pump with a rear clearance of at least 3

inches (76.2 mm) so that the motor can be removed

easily for maintenance and repair.

Note: Do not install this pump within an outer enclosure

or beneath the skirt of a hot tub or spa unless marked

accordingly.

REAR CLEARANCE

3 IN. (76.2 CM) MINIMUM

3 IN.

MINIMUM

Pump Rear Clearance

Recommended Piping

5 x SUCTION PIPE DIAMETER

ELBOW

Only a qualiﬁed plumbing professional should install the SuperFlo® High Performance Pump. Refer to “Pump

Warning And Safety Instructions” on pages ii-iii for additional installation and safety information.

SUPERFLO® High Performance Pump Installation and User’s GuideSUPERFLO® High Performance Pump Installation and User’s Guide

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. This pump must be installed by a licensed or certiﬁed electrician or

a qualiﬁed service professional in accordance with the National Electrical Code and all applicable local codes and ordinances.

Improper installation will create an electrical hazard which could result in death or serious injury to users, installers, or others

due to electrical shock, and may also cause damage to property.

Always disconnect power to the pump at the circuit breaker before servicing the pump. Failure to do so could result in

death or serious injury to service people, pool users or others due to electric shock and/or property damage.

Read all servicing instructions before working on the pump.

1. Be sure all electrical breakers and switches are turned

off before wiring motor.

2. Be sure that the wiring voltage matches the motor

voltage (230 VAC or 115 VAC). If they do not match,

the motor can overheat.

3. Use the correct wire size and type speciﬁed by the

current National Electrical Code. When in doubt use

a heavier gauge (larger diameter) wire. Heavier gauge

will allow the motor to run cooler and more efﬁcient.

4. Be sure all electrical connections are clean and tight.

5. Cut wires to the appropriate length so they do not

overlap or touch when connected to the terminal

board.

6. Permanently ground the motor using the green ground

terminal located on the inside of the motor canopy or

access plate, see image. Use the correct wire size

and type speciﬁed by the current National Electrical

Code. Be sure the ground wire is connected to an

electrical service ground.

7. Bond the motor to the pool structure in accordance

with the current National Electrical Code. UL requires

use of a solid copper bonding conductor not smaller

than 8 AWG.

Electrical Wiring Installation

Field Wiring Compartment

Ground Screw

Pentair offers 2-Pole 20 Amp GFCI breakers

(P/N PA220GF) which offer 6 milliamp personnel

protection while meeting 2008 to current NEC

Standards for Pool Pumps.

Note: When pump is mounted permanently

within 5 ft. (1.52 meters) of the inside walls of

a swimming pool, you must use a No. 8 AWG

or larger conductor to connect to bonding

conductor lug.

Note: When the pump is started and stopped by

removing power with a relay or timer, a two-pole

device should be used to apply and remove

power to both POWER LINE TERMINALS.

8. Connect the wire from the accessible wire connector

on the motor to all metal parts of the swimming

pool, spa, or hot tub structure and to all electrical

equipment, metal conduit, and metal piping within 5

feet (1.52 meters) of the inside walls of the swimming

pool, spa, or hot tub. For Canada, a 6 AWG or larger

solid copper bonding conductor is required.

9. The pump should be permanently connected to

either a circuit breaker, 2-pole timer or 2-pole

relay. If AC power is supplied by a GFCI circuit

breaker, use a dedicated circuit breaker that has

no other electrical loads.

10. Connect the pump permanently to a circuit.

Make sure no other lights or appliances are on

the same circuit.

SUPERFLO® High Performance Pump Installation and User’s Guide

MAINTENANCE

Pump Strainer Basket

The pump strainer basket (or ‘strainer pot’, ‘hair and lint

pot’), is located in front of the volute. Inside the chamber

is the basket which must be kept clean of leaves and

debris at all times. View basket through the ‘See Through

Lid’ to inspect for leaves and debris.

Regardless of the length of time between ﬁlter cleaning,

it is most important to visually inspect the basket at least

once a week. A dirty basket will reduce the efﬁciency of

the ﬁlter and heater and also put an abnormal stress on

the pump motor which would result in a costly repair bill.

DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot. Pumps operated

in these circumstances may experience a build up of vapor pressure and may contain scalding hot water. Opening the pump may

cause serious personal injury. In order to avoid the possibility of personal injury, make sure the suction and discharge valves are

open and strainer pot temperature is cool to touch, then open with extreme caution.

To prevent damage to the pump and for proper operation of the system, clean pump strainer and skimmer baskets regularly.

Cleaning the Pump Strainer Basket

1. Turn off the pump at the circuit breaker.

2. Relieve pressure in the system by allowing the water

to cool.

3. Gently tap the clamp in a counter-clockwise direction

to remove the clamp and lid.

4. Remove debris and rinse out the basket. Replace

the basket if it is cracked.

5. Put the basket back into the housing. Be sure to align

the notch in the bottom of the basket with the rib in

the bottom of the volute.

6. Fill the pump pot and volute up to the inlet port with

water.

7. Clean the cover, O-ring, and sealing surface of the

pump pot. Note: It is important to keep the lid O-ring

clean and well lubricated.

8. Reinstall the lid by placing the lid on the pot. Be sure

the lid O-ring is properly placed. Seat the clamp and

lid on the pump then turn clockwise until the handles

are horizontal.

9. Turn the power “ON” at the house circuit breaker.

Reset the pool time clock to the correct time.

10. Open the High Flow manual air relief valve on top of

the ﬁlter.

11. Stand clear of the ﬁlter. Start the pump.

12. Bleed air from the ﬁlter until a steady stream of water

comes out. Close the High Flow™ Manual Air Relief

Valve.

THIS SYSTEM OPERATES UNDER HIGH

PRESSURE. When any part of the circulating

system (e.g., Lock Ring, Pump, Filter, Valves, etc.)

is serviced, air can enter the system and become

pressurized. Pressurized air can cause the lid to

separate which can result in serious injury, death,

or property damage. To avoid this potential hazard,

follow above instructions.

Strainer Pot Assembly

Winterizing

You are responsible for determining when freezing

conditions may occur. If freezing conditions are

expected, take the following steps to reduce the risk of

freeze damage. Freeze damage is not covered under

warranty.

To prevent freeze damage, follow the procedures below:

1. Shut off electrical power for the pump at the circuit

breaker.

2. Drain the water out of the pump housing by

removing the two thumb-twist drain plugs from the

housing. Store the plugs in the pump basket.

3. Cover the motor to protect it from severe rain, snow

and ice.

Note: Do not wrap motor with plastic or other air tight

materials during winter storage. The motor may be

covered during a storm, winter storage, etc., but never

when operating or expecting operation.

In mild climate areas, when temporary freezing

conditions may occur, run your ﬁltering equipment

all night to prevent freezing.

CLAMP

LID

O-RING

BASKET

VOLUTE

SUPERFLO® High Performance Pump Installation and User’s GuideSUPERFLO® High Performance Pump Installation and User’s Guide

Care of Electric Motor

Protect from heat

1. Shade the motor from the sun.

2. Any enclosure must be well ventilated to prevent

overheating.

3. Provide ample cross ventilation.

Protect against dirt

1. Protect from any foreign matter or splashing water.

2. Do not store (or spill) chemicals on or near the motor.

3. Protect from any foreign matter or splashing water.

4. Avoid sweeping or stirring up dust near the motor

while it is operating.

5. If a motor has been damaged by dirt it voids the

motor warranty.

6. Clean the lid and clamp, O-ring, and sealing surface

of the pump pot.

Protect against moisture

1. Protect from splashing or sprayed water.

2. Protect from extreme weather.

3. Protect from any foreign matter or splashing water.

4. If a motor has become wet - let it dry before operating.

Do not allow the pump to operate if it has been ﬂooded.

5. If a motor has been damaged by water it voids the

motor warranty.

SERVICING

Always disconnect power to the pump at the circuit breaker and disconnect the communication cable before servicing the pump.

Failure to do so could result in death or serious injury to service people, users or others due to electric shock. Read all servicing

instructions before working on the pump.

DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot. Pumps operated

in these circumstances may experience a build up of vapor pressure and may contain scalding hot water. Opening the pump may

cause serious personal injury. In order to avoid the possibility of personal injury, make sure the suction and discharge valves are

open and strainer pot temperature is cool to touch, then open with extreme caution.

Be sure not to scratch or mar the polished shaft seal faces; seal will leak if faces are damaged. The polished and lapped faces of

the seal could be damaged if not handled with care.

Note: When replacing the motor, be certain that the

motor support is correctly positioned to support the

size of motor being installed.

Pump Disassembly

All moving parts are located in the rear sub-assembly

of this pump.

Tools required:

• 1/4 inch socket or open end wrench.

• 9/16 inch open end wrench.

• 1/2 inch or 7/16 inch open end wrench

• Flat blade screwdriver.

To remove and repair the motor subassembly, follow the

steps below:

1. Turn off the pump circuit breaker at the main panel.

2. Drain the pump by removing the drain plugs.

3. Remove the 4 bolts that hold the main pump body

(strainer pot/volute) to the rear sub-assembly.

4. GENTLY pull the two pump halves apart, removing

the rear sub-assembly.

5. Remove the three hex head screws holding the

diffuser in position.

6. Hold the impeller securely in place and remove the

impeller lock screw by using a ﬂat blade screwdriver

or wrench. The screw is a left-handed thread and

loosens in a clockwise direction.

7. Remove the shaft cap located at the back of the

motor and hold the shaft secure with a 1/2 inch

(Century® motors) or 7/16 inch (Franklin Electric®

Motors) open-end wrench. On AO Smith® motors,

remove the motor canopy, move the capacitor to

one side and hold the shaft with a 7/16 inch open-

end wrench.

8. To unscrew the impeller from the shaft, twist the

impeller counter-clockwise.

9. Remove the four bolts from the seal plate to the

motor using a 9/16 inch wrench.

10. Place the seal plate face down on a ﬂat surface

and tap out the ceramic seal.

11. Clean the seal plate, seal housing, and the motor

shaft.

Shaft Seal Replacement

The Shaft Seal consists primarily of two parts, a

rotating member and a ceramic seal.

The pump requires little or no service other than

reasonable care, however, a Shaft Seal may

occasionally become damaged and must be replaced.

Note: The polished and lapped faces of the seal could

be damaged if not handled with care.

SUPERFLO® High Performance Pump Installation and User’s Guide

Pump Reassembly

1. When installing the replacement seal into the seal

plate, use soapy water to wet the rubber boot before

pressing it into the seal plate.

2. Remount the seal plate to the motor.

3. Before installing the rotating portion of the seal on

the motor shaft, wet the motor shaft with soapy water

and slide the seal onto the motor shaft. Ensure that

the carbon face contacts the ceramic face of the

stationary seat. Press the seal into the seal plate

with your thumbs and wipe off the ceramic with a

clean cloth.

4. Grease the motor shaft thread and screw impeller

onto the motor shaft.

5. Screw in the impeller lock screw (counter-clockwise

to tighten).

6. Remount the diffuser onto the seal plate. Make

sure the plastic pins and holding screw inserts are

aligned.

7. Grease the diffuser quad ring and seal plate O-ring

prior to reassembly.

8. Grease the bolt threads, assemble the motor sub-

assembly to the strainer pot-pump body by using

the two through bolts for proper alignment. Do not

tighten the through bolts until all 4 bolts are in place

and ﬁnger tightened.

9. Fill the pump with water.

10. Reinstall the pump lid and plastic clamp;

see the next section, ‘Restart Instructions’.

11. Reprime the system.

Restart Instructions

If pump is installed below the water level of the pool,

close return and suction lines prior to opening hair and

lint pot on pump. Make sure to re-open valves prior to

operating.

Priming the Pump

The pump strainer pot must be ﬁlled with water before

the pump is initially started.

Follow these steps to prime the pump:

1. Remove the pump lid plastic clamp. Remove the

pump lid.

2. Fill the pump strainer pot with water.

3. Reassemble the pump cover and plastic clamp onto

the strainer pot. The pump is now ready to prime.

4. Open the air release valve on the ﬁlter, and stand

clear of the ﬁlter.

5. Turn on the switch or time clock.

6. When water comes out of the air release valve,

close the valve. The system should now be free of

air and recirculating water to and from the pool.

7. For 2-speed pumps:

• Pump should run on high-speed for priming.

• The pump should not run longer than 8

minutes before priming is achieved.

DO NOT run the pump dry. If the pump is run dry, the mechanical seal will be damaged and the pump will start leaking. If this

occurs, the damaged seal must be replaced. ALWAYS maintain proper water level. If the water level falls below the suction port,

the pump will draw air through the suction port, losing the prime and causing the pump to run dry, resulting in a damaged seal.

Continued operation in this manner could cause a loss of pressure, resulting in damage to the pump case, impeller and seal and

may cause property damage and personal injury.

IMPELLER

LOCKING

SCREW

QUAD

RING

DIFFUSER

SCREW IMPELLER

SEAL PLATE O-RING

MOTOR SHAFT

MOTOR SLINGER

SEAL PLATE

BOLT

Motor Assembly

SUPERFLO® High Performance Pump Installation and User’s GuideSUPERFLO® High Performance Pump Installation and User’s Guide

TROUBLESHOOTING

Problem Possible Cause Corrective Action

Pump failure. Pump will not prime - Air leak, too much air.

Pump will not prime - Not enough water.

Pump stainer gasket is clogged.

Pump strainer gasket is defective.

Check suction piping and valve glands on any suction

gate valves. Secure lid on pump strainer pot and be

sure lid gasket is in place. Check water level to be

sure skimmer is not drawing air.

Be sure the suction lines, pump, strainer, and pump

volute are full of water. Be sure valve on suction line

is working and open (some systems do not have

valves). Check water level to make sure water is

available through skimmer.

Clean pump strainer pot.

Replace gasket.

Reduced capacity and/or

head.

Air pockets or leaks in suction line.

Clogged impeller.

Pump strainer clogged.

Check suction piping and valve glands on any suction

gate valves. Secure lid on pump strainer pot and be

sure lid gasket is in place. Check water level to be

sure skimmer is not drawing air.

Turn off electrical power to the pump.

Disassemble (see page 5, ‘Pump Disassembly’)

Clean debris from impeller. If debris cannot be

removed, complete the following steps:

1. Remove left hand thread anti-spin bolt and o-ring.

2. Remove, clean, and reinstall impeller.

Reassemble (see page 6, ‘Pump Reassembly’)

Clean suction trap.

SUPERFLO® High Performance Pump Installation and User’s Guide

SuperFlo® High Performance Pump Parts List

Item Part

No. No. Description

Item Part

No. No. Description

SINGLE SPEED SUPERFLO MOTORS

1 355018S ½, ¾ HP — (Almond)

1 355020S 1 HP — (Almond)

1 355022S 1½ HP — (Almond)

1 355024S 2 HP — (Almond)

1 355026S 2½ HP — (Almond)

DUAL SPEED SUPERFLO MOTORS

1 350088S ¾ HP 115 VOLTAGE — (Almond)

1 355003S 1 HP — (Almond)

1 356630S 1½ HP — (Almond)

1 071320S 2 HP — (Almond)

ENERGY EFFICIENT SUPERFLO MOTORS

1 355008S ½, ¾, 1 HP — (Almond)

1 355010S 1½ HP — (Almond)

1 355012S 2 HP — (Almond)

1 355014S 2½ HP — (Almond)

2 356012 SEAL PLATE

3 350094 BASE

4 350090 CLAMP, RAMP & CAM

5 350091 LID

6 357255 O-RING, LID #2-357

7 350089 VOLUTE

8 350093 ADAPTER, 2 req.

9 350092 NUT, 2 req.

10 192115 O-RING DRAIN PLUG, 2 req.

11 071131 DRAIN PLUG, 2 req.

12 355621 SCREW ¾-16 X 2¼ HEX HD, 4 req.

13 072184 WASHER 3/8 in. S/S, 4 req.

14 355619 O-RING SEAL BRACKET

15 6020018 O-RING ADAPTER #2-226, 2 req.

16 355030 SEAL DIFFUSER

17 355334 SCREW #8-32 HEX WASHER HD, 3 req.

18 355617 DIFFUSER - ½ HP

18 355617 DIFFUSER - ¾ HP

18 355617 DIFFUSER - 1 HP

18 355618 DIFFUSER - 1½ HP

18 355618 DIFFUSER - 2 HP

18 350170 DIFFUSER - 2½ HP

19 U30-74SS HEX HEAD SCREW 3/8 - 16, 4 req.

20 355043 IMPELLER ½ HP

20 355043 IMPELLER ¾ HP

20 355067 IMPELLER 1 HP

20 355074 IMPELLER 1½ HP

20 355086 IMPELLER 2 HP

20 355093 IMPELLER 2½ HP

20 355067 IMPELLER 1 HP, 2-SPD

20 355074 IMPELLER 1½ HP, 2-SPD

20 355086 IMPELLER 2 HP, 2-SPD

21 355389 SCREW, IMPELLER LOCKING

22 354545S SEAL SET

23 355667 BASKET, LARGE

24 350157 KIT UNION SUPERFLO (Items No. 8, 9, 15)

22 20

13 12

11 10

REPLACEMENT PARTS

SUPERFLO® High Performance Pump Installation and User’s GuideSUPERFLO® High Performance Pump Installation and User’s Guide

TECHNICAL DATA

2½ HP

2 HP

1½ HP

1 HP

¾ HP

½ HP

2 HP

1½ HP

1 HP

½, ¾ HP

100

00 120110 13010080 90706040 50302010

Total Dynamic Head in Feet of Water

Flow Rate in U.S. Gallons per Minute

BEST EFFICIENCY SIZING

3450 RPM

1750 RPM

Pump Performance Curves

SPARUS™ 160 Energy Efficient Aquaculture Duty Pump Installation and User’s Guide

NOTES

P/N 350096 REV. G 1/19/16

1620 HAWKINS AVE., SANFORD, NC 27330 • (919) 566-8000

10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000

WWW.PENTAIRPOOL.COM

All Pentair trademarks and logos are owned by Pentair or one of its global affiliates. Pentair Aquatic Systems®, SuperFlo®, Cam and Ramp™ and

High Flow™ are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc. and/or its affiliated companies in the United States

and/ or other countries. Unless expressly noted, names and brands of third parties that may be used in this document are not used to indicate an

affiliation or endorsement between the owners of these names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be

the trademarks or registered trademarks of those third parties. Because we are continuously improving our products and services, Pentair reserves

the right to change specifications without prior notice. Pentair is an equal opportunity employer.

*354707*

LIT PKG. P/N 354707

*350096*

INSTALLATION AND

USER’S GUIDE

WHISPERFLO® High Performance Pump Installation and User’s Guide

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

ENGLISH 1 ESPAÑOL 10

WHISPERFLO®

HIGH PERFORMANCE PUMP

WHISPERFLO® High Performance Pump Installation and User’s Guide

P/N 071109 Rev. J 8/29/14

TABLE OF CONTENTS

Important Pump Warning and

Safety Instructions ..............................................

Installation ............................................................

Location

Piping

Fittings and Valves

Electrical Wiring Installation

Maintenance .........................................................

Pump Strainer Basket

Cleaning the Pump Strainer Basket

Winterizing

Servicing ..............................................................

Motor Care

Shaft Seal Replacement

Pump Disassembly

Pump Reassembly

Restart Instructions

Priming the Pump

If you have questions about ordering Pentair Aquatic Systems replacement parts, and pool products, please contact:

CUSTOMER SERVICE / TECHNICAL SUPPORT

Customer Service and Technical Support, USA

(8 A.M. to 4:30 P.M. — Eastern/Paciﬁc Times)

Phone: (800) 831-7133

Fax: (800) 284-4151

Web site

Visit www.pentairpool.com or www.staritepool.com

Sanford, North Carolina (8 A.M. to 4:30 P.M. ET)

Phone: (919) 566-8000

Fax: (919) 566-8920

Moorpark, California (8 A.M. to 4:30 P.M. PT)

Phone: (805) 553-5000 (Ext. 5591)

Fax: (805) 553-5515

Troubleshooting ....................................................

Replacement Parts ................................................

Illustrated Parts List

Pump Performance Curves

Español Tabla de Contenidos ...............................

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

All Pentair trademarks and logos are owned by Pentair or one of its global afﬁliates. Pentair Aquatic Systems™, WhisperFlo® and

High Flow™ are trademarks and/or registered trademarks of Pentair Water Pool and Spa, Inc. and/or its afﬁliated companies in the

United States and/ or other countries. Unless expressly noted, names and brands of third parties that may be used in this document

are not used to indicate an afﬁliation or endorsement between the owners of these names and brands and Pentair Water Pool

and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those third parties. Because we are

continuously improving our products and services, Pentair reserves the right to change speciﬁcations without prior notice. Pentair

is an equal opportunity employer.

WHISPERFLO® High Performance Pump Installation and User’s Guide

IMPORTANT PUMP WARNING AND SAFETY INSTRUCTIONS

When installing and using this electrical equipment, basic safety

precautions should always be followed, include the following:

Do not permit children to use this product.

RISK OF ELECTRICAL SHOCK. Connect only to

a branch circuit protected by a ground-fault circuit-

interrupter (GFCI). Contact a qualiﬁed electrician if you cannot verify that

the circuit is protected by a GFCI.

This unit must be connected only to a supply circuit

that is protected by a ground-fault circuit-interrupter

(GFCI). Such a GFCI should be provided by the installer and should be

tested on a routine basis. To test the GFCI, push the test button. The

GFCI should interrupt power. Push the reset button. Power should be

restored. If the GFCI fails to operate in this manner, the GFCI is defec-

tive. If the GFCI interrupts power to the pump without the test button

being pushed, a ground current is ﬂowing, indicating the possibility of

an electric shock. Do not use this pump. Disconnect the pump and have

the problem corrected by a qualiﬁed service representative before using.

This pump is for use with permanent swimming

pools and may also be used with hot tubs and spas

if so marked. Do not use with storable pools. A permanently-installed

pool is constructed in or on the ground or in a building such that it cannot

be readily disassembled for storage. A storable pool is constructed so

that it is capable of being readily disassembled for storage and

reassembled to its original integrity.

General Warnings

• Never open the inside of the drive motor enclosure. There is a

capacitor bank that holds a 230 VAC charge even when there is no

power to the unit.

• The pump is not submersible.

• The pump is capable of high ﬂow rates; use caution when installing

and programming to limit pumps performance potential with old or

questionable equipment.

• Code requirements for the electrical connection differ from state to

state. Install equipment in accordance with the National Electrical

Code and all applicable local codes and ordinances.

• Before servicing the pump; switch OFF power to the pump by

disconnecting the main circuit to the pump.

• This appliance is not intended for use by persons (including children) of

reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning the use of the appliance by a person responsible for their

safety.

FAILURE TO FOLLOW ALL INSTRUCTIONS AND

WARNINGS CAN RESULT IN SERIOUS BODILY

INJURY OR DEATH. THIS PUMP SHOULD BE INSTALLED AND

SERVICED ONLY BY A QUALIFIED POOL SERVICE PROFESSIONAL.

INSTALLERS, POOL OPERATORS AND OWNERS MUST READ THESE

WARNINGS AND ALL INSTRUCTIONS IN THE OWNER’S MANUAL

BEFORE USING THIS PUMP. THESE WARNINGS AND THE OWNER’S

MANUAL MUST BE LEFT WITH THE POOL OWNER.

SUCTION ENTRAPMENT HAZARD: STAY OFF

THE MAIN DRAIN AND AWAY FROM ALL SUCTION

OUTLETS!

THE USE OF UNAPPROVED COVERS OR ALLOWING USE OF THE

POOL OR SPA WHEN COVERS ARE MISSING, CRACKED OR BROKEN

CAN RESULT IN BODY OR LIMB ENTRAPMENT, HAIR ENTANGLE-

MENT, BODY ENTRAPMENT, EVISCERATION AND/OR DEATH.

The suction at a drain or outlet can cause:

Limb Entrapment: When a limb is sucked or inserted into an opening

resulting in a mechanical bind or swelling. This hazard is present when

a drain cover is missing, broken, loose, cracked or not properly secured.

Hair Entanglement: When the hair tangles or knots in the drain cover,

trapping the swimmer underwater. This hazard is present when the ﬂow

rating of the cover is too small for the pump or pumps.

Body Entrapment: When a portion of the body is held against the drain

cover trapping the swimmer underwater. This hazard is present when the

drain cover is missing, broken or the cover ﬂow rating is not high enough

for the pump or pumps.

Evisceration/Disembowelment: When a person sits on an open pool

(particularly a child wading pool) or spa outlet and suction is applied directly

to the intestines, causing severe intestinal damage. This hazard is present

when the drain cover is missing, loose, cracked, or not properly secured.

THIS PUMP PRODUCES HIGH LEVELS OF SUCTION AND CREATES

A STRONG VACUUM AT THE MAIN DRAIN AT THE BOTTOM OF THE

BODY OF WATER. THIS SUCTION IS SO STRONG THAT IT CAN TRAP

ADULTS OR CHILDREN UNDER WATER IF THEY COME IN CLOSE

PROXIMITY TO A DRAIN OR A LOOSE OR BROKEN DRAIN COVER

OR GRATE.

This guide provides installation and operation instructions for this product.

Consult Pentair with any questions regarding this equipment.

Attention Installer: This guide contains important information about the

installation, operation and safe use of this product. This information should

be given to the owner and/or operator of this equipment after installation

or left on or near the pump.

Attention User: This manual contains important information that will help

you in operating and maintaining this product. Please retain it for future

reference.

This is the safety alert symbol. When you see this

symbol on your system or in this manual, look for

one of the following signal words and be alert to

the potential for personal injury.

Warns about hazards that can cause death,

serious personal injury, or major property damage

if ignored.

Warns about hazards that may cause death,

serious personal injury, or major property damage

if ignored.

Warns about hazards that may or can cause

minor personal injury or property damage

if ignored.

NOTE indicates special instructions not related to hazards.

Carefully read and follow all safety instructions in this manual and on

equipment. Keep safety labels in good condition; replace if missing

or damaged.

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

IMPORTANT NOTICE

ENGLISH

ESPAÑOL

For Installation of Electrical Controls at Equipment Pad (ON/OFF

Switches, Timers and Automation Load Center)

Install all electrical controls at equipment pad, such as

on/off switches, timers, and control systems, etc. to

allow the operation (startup, shut-down, or servicing)

of any pump or ﬁlter so the user does not place any

portion of his/her body over or near the pump strainer

lid, ﬁlter lid or valve closures. This installation should

allow the user enough space to stand clear of the

ﬁlter and pump during system start-up, shut down or

servicing of the system ﬁlter.

Pentair Water Pool and Spa®

IMPORTANT SAFETY INSTRUCTIONS

For Installation of Electrical Controls at Equipment Pad

(ON/OFF Switches, Timers and Automation Load Center)

Install all electrical controls at equipment pad, such as on/off

switches, timers, and control systems, etc. to allow the

operation (startup, shut-down, or servicing) of any pump or

filter so the user does not place any portion of his/her body

over or near the pump strainer lid, filter lid or valve closures.

This installation should allow the user enough space to stand

clear of the filter and pump during system start-up, shut down

or servicing of the system filter.

SAVE THESE INSTRUCTIONS

WHISPERFLO® High Performance Pump Installation and User’s Guide

iii

IMPORTANT PUMP WARNING AND SAFETY INSTRUCTIONS

HAZARDOUS PRESSURE: STAND CLEAR OF

PUMP AND FILTER DURING START UP

Circulation systems operate under high pressure.

When any part of the circulating system (i.e.

locking ring, pump, ﬁlter, valves, etc.) is serviced,

air can enter the system and become pressurized.

Pentair Water Pool and Spa®

IMPORTANT SAFETY INSTRUCTIONS

For Installation of Electrical Controls at Equipment Pad

(ON/OFF Switches, Timers and Automation Load Center)

Install all electrical controls at equipment pad, such as on/off

switches, timers, and control systems, etc. to allow the

operation (startup, shut-down, or servicing) of any pump or

filter so the user does not place any portion of his/her body

over or near the pump strainer lid, filter lid or valve closures.

This installation should allow the user enough space to stand

clear of the filter and pump during system start-up, shut down

or servicing of the system filter.

Before servicing equipment, make note of the ﬁlter pressure. Be sure

that all controls are set to ensure the system cannot inadvertently start

during service. Turn off all power to the pump. IMPORTANT: Place ﬁlter

manual air relief valve in the open position and wait for all pressure

in the system to be relieved.

Before starting the system, fully open the manual air relief valve and place

all system valves in the “open” position to allow water to ﬂow freely from the

tank and back to the tank. Stand clear of all equipment and start the pump.

IMPORTANT: Do not close ﬁlter manual air relief valve until all

pressure has been discharged from the valve and a steady stream

of water appears. Observe ﬁlter pressure gauge and be sure it is not

higher than the pre-service condition.

Pressurized air can cause the pump housing cover ﬁlter lid and valves

to violently separate which can result in severe personal injury or death.

Filter tank lid and strainer cover must be properly secured to prevent

violent separation. Stand clear of all circulation system equipment when

turning on or starting up pump.

General Installation Information

• All work must be performed by a qualiﬁed service professional, and

must conform to all national, state, and local codes.

• Install to provide drainage of compartment for electrical components.

• These instructions contain information for a variety of pump models

and therefore some instructions may not apply to a speciﬁc model. All

models are intended for use in swimming pool applications. The pump

will function correctly only if it is properly sized to the speciﬁc application

and properly installed.

Pumps improperly sized or installed or used in

applications other than for which the pump was

intended can result in severe personal injury or death. These risks may

include but not be limited to electric shock, ﬁre, ﬂooding, suction

entrapment or severe injury or property damage caused by a structural

failure of the pump or other system component.

The pump can produce high levels of suction within

the suction side of the plumbing system. These high

levels of suction can pose a risk if a person comes within the close

proximity of the suction openings. A person can be seriously injured by

this high level of vacuum or may become trapped and drown. It is

absolutely critical that the suction plumbing be installed in accordance

with the latest national and local codes for swimming pools.

The Virginia Graeme Baker (VGB) Pool and Spa Safety Act creates

new requirements for owners and operators of commercial swimming

pools and spas.

Commercial pools or spas constructed on or after December 19, 2008,

shall utilize:

(A) A multiple main drain system without isolation capability with suction

outlet covers that meet ASME/ANSI A112.19.8a Suction Fittings for

Use in Swimming Pools, Wading Pools, Spas, and Hot Tubs and either:

(i) A safety vacuum release system (SVRS) meeting ASME/ANSI

A112.19.17 Manufactured Safety Vacuum Release systems (SVRS)

for Residential and Commercial Swimming Pool, Spa, Hot Tub,

and Wading Pool Suction Systems and/or ASTM F2387 Standard

Speciﬁcation for Manufactured Safety Vacuum Release Systems

(SVRS) for Swimming pools, Spas and Hot Tubs or

(ii) A properly designed and tested suction-limiting vent system or

(iii) An automatic pump shut-off system.

Commercial pools and spas constructed prior to December 19, 2008,

with a single submerged suction outlet shall use a suction outlet cover

that meets ASME/ANSI A112.19.8a and either:

(A) A SVRS meeting ASME/ANSI A112.19.17 and/or ASTM F2387, or

(B) A properly designed and tested suction-limiting vent system, or

(D) Disabled submerged outlets, or

(E) Suction outlets shall be re-conﬁgured into return inlets.

A clearly labeled emergency shut-off switch for the

pump must be in an easily accessible, obvious place.

TO MINIMIZE THE RISK OF INJURY DUE TO

SUCTION ENTRAPMENT HAZARD:

• A properly installed and secured ANSI/ASME A112.19.8 approved

anti-entrapment suction cover must be used for each drain.

• Each suction cover must be installed at least three (3’) feet apart,

as measured from the nearest point to nearest point.

• Regularly inspect all covers for cracks, damage and advanced

weathering.

• If a cover becomes loose, cracked, damaged, broken or is missing,

replace with an appropriate certiﬁed cover.

• Replace drain covers as necessary. Drain covers deteriorate over

time due to exposure to sunlight and weather.

• Avoid getting hair, limbs or body in close proximity to any suction

cover, pool drain or outlet.

• Disable suction outlets or reconﬁgure into return inlets.

Make sure users know where it is and how to use it in case of emergency.

Mechanical Entrapment: When jewelry, swimsuit, hair decorations,

ﬁnger, toe or knuckle is caught in an opening of an outlet or drain cover.

This hazard is present when the drain cover is missing, broken, loose,

cracked, or not properly secured.

NOTE: ALL SUCTION PLUMBING MUST BE INSTALLED IN

ACCORDANCE WITH THE LATEST NATIONAL AND LOCAL CODES,

STANDARDS AND GUIDELINES.

Warnings and safety instructions for Pentair Aquatic Systems

pumps and other related products are available at:

http://www.pentairpool.com/pool-owner/safety-warnings/ or call

(800) 831-7133 for additional free copies of these instructions.

Please refer to http://www.pentairpool.com/pool-owner/

safetywarnings/ for warning and safety instructions related to

this product.

WHISPERFLO® High Performance Pump Installation and User’s GuideWHISPERFLO® High Performance Pump Installation and User’s Guide

ENGLISH

ESPAÑOL

Location

Be sure the pump location meets the following

requirements:

Piping

1. For improved pool plumbing, it is recommended to

use a larger pipe size. When installing the inlet and

outlet ﬁttings (male adaptors), use thread sealant.

2. Piping on the suction side of the pump should be the

same or larger than the return line diameter.

3. Plumbing on the suction side of the pump should be

as short as possible.

4. It is recommended that a valve, elbow or tee installed

in the suction line should be no closer to the front

of the pump than ﬁve (5) times the suction line pipe

diameter

Example:

A 2 inch (50.8 mm) pipe requires a 10 inch (254

mm) straight run in front of the suction inlet of the

pump. This will help the pump prime faster and last

longer.

Fittings and Valves

1. Do not install 90° elbows directly into pump inlet.

2. Flooded suction systems should have gate valves

installed on suction and discharge pipes for

maintenance, however, the suction gate valve should

be no closer than ﬁve times the suction pipe diameter

as described in this section.

3. Use a check valve in the discharge line when using

this pump for any application where there is signiﬁcant

height to the plumbing after the pump.

4. Be sure to install check valves when plumbing in

parallel with another pump. This helps prevent reverse

rotation of the impeller and motor.

1. Install the pump as close to the pool or spa as possible.

To reduce friction loss and improve efﬁciency, use

short, direct suction piping returns.

2. Install a minimum of 5 feet (1.52 meters) from the

inside wall of the pool and spa. Canadian installations

require a minimum of 9.8 feet (3 meters) from pool

water level.

3. Install the pump a minimum of 3 feet (.9 meters) from

the heater outlet.

4. Do not install the pump more than 10 feet (3 meters)

above the water level.

5. Install the pump in a well ventilated location protected

from excessive moisture (i.e., rain gutter downspouts,

sprinklers, etc.)

6. Install the pump with a rear clearance of at least 3

inches (76.2 mm) so that the motor can be removed

easily for maintenance and repair.

Note: Do not install this pump within an outer enclosure

or beneath the skirt of a hot tub or spa unless marked

accordingly.

REAR CLEARANCE

3 IN. (76.2 CM) MINIMUM

3 IN.

MINIMUM

Pump Rear Clearance

Recommended Piping

5 x SUCTION PIPE DIAMETER

ELBOW

INSTALLATION

Only a qualiﬁed plumbing professional should install the WhisperFlo® High Performance Pump. Refer to “Pump

Warning And Safety Instructions” on pages ii - iii for additional installation and safety information.

WHISPERFLO® High Performance Pump Installation and User’s Guide

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION. This pump must be installed by a licensed or certiﬁed electrician or

a qualiﬁed service professional in accordance with the National Electrical Code and all applicable local codes and ordinances.

Improper installation will create an electrical hazard which could result in death or serious injury to users, installers, or others

due to electrical shock, and may also cause damage to property.

Always disconnect power to the pump at the circuit breaker before servicing the pump. Failure to do so could result in

death or serious injury to service people, pool users or others due to electric shock and/or property damage.

Read all servicing instructions before working on the pump.

1. Be sure all electrical breakers and switches are turned

off before wiring motor.

2. Be sure the supply line voltage matches the motor

voltage listed on the motor plate (example 230 VAC

or 115 VAC). If they do not match, permanent motor

damage may occur.

3. Use strain relief and be sure all electrical connections

are clean and tight.

4. Cut wires to the appropriate length so they don’t

overlap or touch when connected to the terminal

board.

5. Permanently ground the motor using the green ground

terminal located on the inside of the motor canopy or

access plate, see Figure 1. Use the correct wire size

and type speciﬁed by National Electrical Code. Make

sure the ground wire is connected to an electrical

service ground.

6. Bond the motor to the pool structure in accordance

with the National Electrical Code. Use a solid No. 8

AWG or larger copper conductor. Run a wire from

the external bonding to the pool bonding structure.

7. Connect the wire from the accessible bonding lug on

the motor to all metal parts of the swimming pool, spa,

or hot tub structure and to all electrical equipment,

metal conduit, and metal piping within 5 feet (1.52

meters) of the inside walls of the swimming pool,

spa, or hot tub. For Canada, a 6 AWG or larger solid

copper bonding conductor is required.

8. The pump should be permanently connected to

either a circuit breaker, 2-pole timer or 2-pole relay.

If AC power is supplied by a GFCI circuit breaker,

use a dedicated circuit breaker that has no other

electrical loads.

Electrical Wiring Installation

Figure 1. Field Wiring Compartment

Ground Screw

Pentair offers 2-Pole 20 Amp GFCI breakers

(P/N PA220GF) which offer 6 milliamp personnel

protection while meeting 2008 to current NEC

Standards for Pool Pumps.

Note: When the pump is started and stopped by

removing power with a relay or timer, a two-pole

device should be used to apply and remove

power to both POWER LINE TERMINALS.

WHISPERFLO® High Performance Pump Installation and User’s GuideWHISPERFLO® High Performance Pump Installation and User’s Guide

ENGLISH

ESPAÑOL

Ground Screw

MAINTENANCE

Pump Strainer Basket

The pump strainer basket (or ‘strainer pot’, ‘hair and lint

pot’), is located in front of the volute. Inside the chamber

is the basket which must be kept clean of leaves and

debris at all times. View basket through the ‘See Through

Lid’ to inspect for leaves and debris.

Regardless of the length of time between ﬁlter cleaning,

it is most important to visually inspect the basket at least

once a week. A dirty basket will reduce the efﬁciency of

the ﬁlter and heater and also put an abnormal stress on

the pump motor which would result in a costly repair bill.

DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot. Pumps operated

in these circumstances may experience a build up of vapor pressure and may contain scalding hot water. Opening the pump may

cause serious personal injury. In order to avoid the possibility of personal injury, make sure the suction and discharge valves are

open and strainer pot temperature is cool to touch, then open with extreme caution.

To prevent damage to the pump and for proper operation of the system, clean pump strainer and skimmer baskets regularly.

Cleaning the Pump Strainer Basket

1. Turn off the pump at the circuit breaker.

2. Relieve pressure in the system by allowing the water

to cool.

3. Gently tap the clamp in a counter-clockwise direction

to remove the clamp and lid.

4. Remove debris and rinse out the basket. Replace

the basket if it is cracked.

5. Put the basket back into the housing. Be sure to align

the notch in the bottom of the basket with the rib in

the bottom of the volute.

6. Fill the pump pot and volute up to the inlet port with

water.

7. Clean the cover, O-ring, and sealing surface of the

pump pot. Note: It is important to keep the lid O-ring

clean and well lubricated.

8. Reinstall the lid by placing the lid on the pot. Be sure

the lid O-ring is properly placed. Seat the clamp and

lid on the pump then turn clockwise until the handles

are horizontal.

9. Turn the power “ON” at the house circuit breaker.

Reset the pool time clock to the correct time.

10. Open the High Flow manual air relief valve on top of

the ﬁlter.

11. Stand clear of the ﬁlter. Start the pump.

12. Bleed air from the ﬁlter until a steady stream of water

comes out. Close the High Flow™ Manual Air Relief

Valve.

THIS SYSTEM OPERATES UNDER HIGH

PRESSURE. When any part of the circulating

system (e.g., Lock Ring, Pump, Filter, Valves, etc.)

is serviced, air can enter the system and become

pressurized. Pressurized air can cause the lid to

separate which can result in serious injury, death,

or property damage. To avoid this potential hazard,

follow above instructions.

Clamp, pot

O-Ring

Lid

Strainer

Basket

Pot

Drain

Plugs

Volute

Strainer Pot Assembly

Winterizing

You are responsible for determining when freezing

conditions may occur. If freezing conditions are

expected, take the following steps to reduce the risk

of freeze damage. Freeze damage is not covered

under warranty.

To prevent freeze damage, follow the procedures below:

1. Shut off electrical power for the pump at the circuit

breaker.

2. Drain the water out of the pump housing by removing

the two thumb-twist drain plugs from the housing.

Store the plugs in the pump basket.

3. Cover the motor to protect it from severe rain, snow

and ice.

Note: Do not wrap motor with plastic or other air tight

materials during winter storage. The motor may be

covered during a storm, winter storage, etc., but never

when operating or expecting operation.

In mild climate areas, when temporary freezing

conditions may occur, run your ﬁltering equipment

all night to prevent freezing.

WHISPERFLO® High Performance Pump Installation and User’s Guide

Care of Electric Motor

Protect from heat

1. Shade the motor from the sun.

2. Any enclosure must be well ventilated to prevent

overheating.

3. Provide ample cross ventilation.

Protect against dirt

1. Protect from any foreign matter or splashing water.

2. Do not store (or spill) chemicals on or near the motor.

3. Protect from any foreign matter or splashing water.

4. Avoid sweeping or stirring up dust near the motor

while it is operating.

5. If a motor has been damaged by dirt it voids the

motor warranty.

6. Clean the lid and clamp, O-ring, and sealing surface

of the pump pot.

Protect against moisture

1. Protect from splashing or sprayed water.

2. Protect from extreme weather.

3. Protect from any foreign matter or splashing water.

4. If a motor has become wet - let it dry before operating.

Do not allow the pump to operate if it has been ﬂooded.

5. If a motor has been damaged by water it voids the

motor warranty.

SERVICING

Always disconnect power to the pump at the circuit breaker and disconnect the communication cable before servicing the pump.

Failure to do so could result in death or serious injury to service people, users or others due to electric shock. Read all servicing

instructions before working on the pump.

DO NOT open the strainer pot if pump fails to prime or if pump has been operating without water in the strainer pot. Pumps operated

in these circumstances may experience a build up of vapor pressure and may contain scalding hot water. Opening the pump may

cause serious personal injury. In order to avoid the possibility of personal injury, make sure the suction and discharge valves are

open and strainer pot temperature is cool to touch, then open with extreme caution.

Be sure not to scratch or mar the polished shaft seal faces; seal will leak if faces are damaged. The polished and lapped faces of

the seal could be damaged if not handled with care.

Note: When replacing the motor, be certain that the

motor support is correctly positioned to support the

size of motor being installed.

Pump Disassembly

All moving parts are located in the rear sub-assembly

of this pump.

Tools required:

• 3/32 inch Allen head wrench

• 1/2 inch open end wrench

• 9/16 inch open end wrench

• Flat blade screwdriver

• #2 Phillips scewdriver

To remove and repair the motor subassembly, follow the

steps below:

1. Turn off the pump circuit breaker at the main panel.

2. Drain the pump by removing the drain plugs.

3. Remove the 6 bolts that hold the main pump body

(strainer pot/volute) to the rear sub-assembly.

4. GENTLY pull the two pump halves apart, removing

the rear sub-assembly.

5. Use a 3/32 inch Allen head wrench to loosen the

two holding screws located on the diffuser.

6. Hold the impeller securely in place and remove

the impeller lock screw by using a #2 Phillips

screwdriver. The screw is a left-handed thread and

loosens in a clockwise direction.

7. Remove the shaft cap located at the back of the

motor and hold the shaft secure with a ½ inch

open-end wrench.

8. To unscrew the impeller from the shaft, twist the

impeller counterclockwise.

9. Remove the four bolts from the seal plate to the

motor, using a 9/16 inch wrench.

Shaft Seal Replacement

The Shaft Seal consists primarily of two parts, a rotating

member and a ceramic seal.

The pump requires little or no service other than

reasonable care, however, a Shaft Seal may occasionally

become damaged and must be replaced.

Note: The polished and lapped faces of the seal could

be damaged if not handled with care.

WHISPERFLO® High Performance Pump Installation and User’s GuideWHISPERFLO® High Performance Pump Installation and User’s Guide

ENGLISH

ESPAÑOL

Pump Reassembly

1. When installing the replacement shaft seal, use

silicone sealant on the metal portion before

pressing into the seal plate, being careful to keep

off of the seal face. Ensure the seal is fully seated

and allow 24 hours for sealant to cure. (Complete

seal plate w/seal replacement kit available, P/N

350201/350101.)

2. Before installing the ceramic section of the seal into

the impeller, be sure the impeller is clean. Use a

light density soap and water to seal the seal. Press

the seal into the impeller with your thumbs and wipe

off the ceramic and carbon faces with a clean cloth.

3. Remount the seal plate to the motor by installing

bolts in an X pattern and tightening to 70 in-lbs.

4. Clean the motor shaft thread and the impeller

insert, then screw the impeller onto the motor shaft.

5. Screw in the impeller lock screw (counter-clockwise

and tighten to 25 in-lbs. while holding the motor

shaft with wrench).

6. Remount the diffuser onto the seal plate. Make

sure the plastic pins and holding screw inserts are

aligned.

7. Grease the diffuser O-ring and seal plate gasket.

8. Grease the bolt threads, assemble the motor sub-

assembly to the strainer pot-pump body by using

the two through bolts for proper alignment. Do not

tighten the through bolts until all 6 bolts are in place

and ﬁnger tightened. Torque in a cross pattern to

110 in-lbs.

9. Fill the pump with water.

10. Reinstall the pump lid and plastic clamp;

see the next section, ‘Restart Instructions’.

11. Reprime the system.

Restart Instructions

If pump is installed below the water level of the pool,

close return and suction lines prior to opening hair and

lint pot on pump. Make sure to re-open valves prior to

operating.

Priming the Pump

The pump strainer pot must be ﬁlled with water before

the pump is initially started. Follow these steps to

prime the pump:

1. Remove the pump lid plastic clamp. Remove the

pump lid.

2. Fill the pump strainer pot with water.

3. Reassemble the pump cover and plastic clamp onto

the strainer pot. The pump is now ready to prime.

4. Open the air release valve on the ﬁlter, and stand

clear of the ﬁlter.

5. Turn on the switch or time clock.

6. When water comes out of the air release valve,

close the valve. The system should now be free of

air and recirculating water to and from the pool.

7. For 2-speed pumps:

• Pump should run on high-speed for priming.

• The pump should not run longer than 8 minutes

before priming is achieved.

DO NOT run the pump dry. If the pump is run dry, the mechanical seal will be damaged and the pump will start leaking. If this

occurs, the damaged seal must be replaced. ALWAYS maintain proper water level. If the water level falls below the suction port,

the pump will draw air through the suction port, losing the prime and causing the pump to run dry, resulting in a damaged seal.

Continued operation in this manner could cause a loss of pressure, resulting in damage to the pump case, impeller and seal and

may cause property damage and personal injury.

MOTOR SHAFT

BOLT

SEAL PLATE

LOCKSCREW

LOCKSREW SEAL

IMPELLER

GASKET

Motor Assembly

WHISPERFLO® High Performance Pump Installation and User’s Guide

TROUBLESHOOTING

Problem Possible Cause Corrective Action

Pump failure. Pump will not prime - Air leak, too much air.

Pump will not prime - Not enough water.

Pump stainer gasket is clogged.

Pump strainer gasket is defective.

Check suction piping and valve glands on any suction

gate valves. Secure lid on pump strainer pot and be

sure lid gasket is in place. Check water level to be

sure skimmer is not drawing air.

Be sure the suction lines, pump, strainer, and pump

volute are full of water. Be sure valve on suction line

is working and open (some systems do not have

valves). Check water level to make sure water is

available through skimmer.

Clean pump strainer pot.

Replace gasket.

Reduced capacity and/or

head.

Air pockets or leaks in suction line.

Clogged impeller.

Pump strainer clogged.

Check suction piping and valve glands on any suction

gate valves. Secure lid on pump strainer pot and be

sure lid gasket is in place. Check water level to be

sure skimmer is not drawing air.

Turn off electrical power to the pump.

Disassemble (see page 4, ‘Pump Disassembly’)

Clean debris from impeller. If debris cannot be

removed, complete the following steps:

1. Remove left hand thread anti-spin bolt and o-ring.

2. Remove, clean, and reinstall impeller.

Reassemble (see page 5, ‘Pump Reassembly’)

Clean suction trap.

WHISPERFLO® High Performance Pump Installation and User’s GuideWHISPERFLO® High Performance Pump Installation and User’s Guide

ENGLISH

ESPAÑOL

Item

No. P/N Description

1 357199 Clamp, Cam & Ramp, Almond

1 357150 Clamp, Cam & Ramp, Black

2 357151 Cover, Clear, WFE Pump

2 357156 Cover, chemical resistant Cam & Ramp

3 350013 O-Ring, WFE Cover

4 070387 Strainer Basket, WFE

5 070430 Bolt, 3/8 - 16 x 1.25 Hex Head. SS, 4

Req.

6 072184 Washer, 3/8 x 13/16 O.D. SS, 6 Req.

7 070431 Bolt, 3/8 - 16 x 1.75 Hex Head. SS, 2

Req.

8 071403 Nut, 3/8, 16 Hex Head, 2 Req.

9 357100 Black Gasket for Seal Plate

10 357149 Volute & Seal Plate, Almond

Replacement Kit

10 350015 Volute, WFE Pump & Pot, Almond

10 357157 Volute, WFE Pump & Pot, Black

11 355227 O-Ring Parker No. 2-238, WFE Pump

12 071660 Set Screw, 4-40 x 1-1/8 WFE, 2 Req.

13 072928 Diffuser assembly, WFE-12, 3 HP Only

13 072927 Diffuser assembly, WFE 2-8,

1/2 HP-2.5 HP

14 071652 Set Screw, 1/4 - 20 x 1 in. Phillips

Item

No. P/N Description

15 075713 Rubber Washer, WFE Pump

16 071734S Seal PA-7 w/ ceramic seat, PS1000

16 071728 Seal A7 w/ ceramic seat, PS201

17 070429 Bolt 3/8 - 16 x 7/8 SS Hex Head, 4 Req.

18 350201 Seal Plate Kit WFE Almond (Includes

Mechanical Seal installed) Items 9, 16 & 18

18 350101 Seal Plate Kit WFE Black (Includes

Mechanical Seal installed) Items 16 & 18

19 070927 Foot, WFE Pump, Almond

19 357159 Foot, Black

20 070929 Foot Insert, WFE Pump, Almond

20 357160 Foot Insert, WFE Pump, Black

21 071657 Screw 1/4 - 20 x 1 In. Hex Head, SS,

2 Req.

22 071406 Nut, 1/4 - 20 Hex Head, SS, 2 Req.

23 072183 Washer, 1/4 x 5/8 OD, SS, 2 Req.

24 071131 Knob, Drain Plug, Almond, 2 Req.

24 357161 Knob, Drain Plug, Black, 2 Req.

25 192115 O-Ring, Drain Plug, 2 Req.

26 357149 Volute/Seal Plate Replacement Kit, Almond

(Incl. Items: 1-4, 9, 10, 16, 18, 24, and 25)

27 See Motor Table on next page

WhisperFlo® High Performance Pump Parts List

24 25

REPLACEMENT PARTS

WHISPERFLO® High Performance Pump Installation and User’s Guide

075451 WFE-2 ﬂuid end, 1/2 HP

075452 WFE-3 ﬂuid end, 3/4 HP

075453 WFE-4 ﬂuid end, 1 HP

075454 WFE-6 ﬂuid end, 1-1/2 HP

075455 WFE-8 ﬂuid end, 2 HP

075456 WFE-12 ﬂuid end, 3 HP

HP PUMP MODEL STD

PART NO.

1/2 WFE-2, WF-2, WF-23, WFK-2 073126

3/4 WFE-3, WFE-24, WF-3, WF-24,

WFK-3, WFDS-24 073127

1WFE-4, WFE-26, WF-4, WF-26,

WFK-4, WFDS-4, WFDS-26 073128

1½ WFE-6, WFE-28, WF-6, WF-28,

WFK-6, WFDS-6, WFDS-28 073129

2WFE-8, WFE-30, WF-8, WF-30,

WFK-8, WFDS-8, WFDS-30 073130

3WFE-12, WF-12, WFK-12 073131

Impeller Chart

Fluid Ends-All Parts, w/o Motor

CSA/CUL (only) for Canada

Energy efﬁcient, single phase

Standard efﬁciency, single phase

Two speed, single phase

075136 WFE-2

075137 WFE-3, WFE-24

075138 WFE-4, WFE-26

075139 WFE-6, WFE-28

075140 WFE-8, WFE-30

075141 WFE-12

075145 WFDS-3, WFDS-24

075142 WFDS-4, WFDS-26

075143 WFDS-6, WFDS-28

075144 WFDS-8, WFDS-30

075251 WF-2, WF-23

075252 WF-3, WF-24

075253 WF-4, WF-26

075254 WF-6,WF-28

075255 WF-8,WF-30

075256 WF-12

Power End Sub-assembly

Includes Items: 12-18, 27-28

Item

No.

P/N Description

Motors

27 355008S 3/4 HP, 60 Hz, WFE-2, 3 & 24, 1 spd., almond, 31 lbs.

27 355010S 1 HP, 60 Hz, WFE-4 & 26, 1 spd., almond, 33 lbs.

27 355012S 1-1/2 HP, 60 Hz, WFE-6 & 28, 1 spd., almond, 39 lbs.

27 355014S 2 HP, 60 Hz, WFE-8 & 30, 1 spd., almond, 40 lbs.

27 355016S 3 HP, 60 Hz, WFE-12, 1 spd., almond, 40 lbs.

27 356630S 1 HP, WFDS-4 & 26, 2 spd., 34 lbs.

27 071320S 1-1/2 HP, WFDS-6 & 28, 2 spd., 36 lbs.

27 071321S 2 HP, WFDS-8 & 30, 2 spd., 45 lbs.

27 355018S 1/2 HP, WF-2 & 23, 1 spd., almond, 39 lbs.

27 355020S 3/4 HP, WF-3 & 24, 1 spd., almond, 26 lbs.

27 355022S 1 HP, WF-4 & 26, 1 spd., almond, 28 lbs.

27 355024S 1-1/2 HP, WF-6 & 28, 1 spd., 39 lbs.

27 355026S 2 HP, WF-8 & 30, 1 spd., 32 lbs.

27 355033S 3 HP, WF-12, 1 spd., almond, 40 lbs.

27 355203S 1 HP, WFK-4, 3 ph, 1 spd., black, 28 lbs.

27 355204S 1-1/2 HP, WFK-6, 3 ph, 1 spd., black, 30 lbs.

27 355205S 2 HP, WFK-8, 3 ph, 1 spd., black, 37 lbs.

27 355398S 3 HP, WFK-12, 3 ph, 1 spd., black, 35 lbs.

27 356626S 1 HP, WFK-4, 3 ph, 1 spd., almond, 28lbs.

27 356627S 1-1/2 HP, WFK-6, 3 ph, 1 spd., almond, 30lbs.

27 356628S 2 HP, WFK-8, 3 ph, 1 spd., almond, 37 lbs.

27 356629S 3 HP, WFK-12, 3 ph, 1 spd., almond, 35 lbs.

354805S

354807S

354809S

354811S

1 HP, WFK-4, TEFC, 3 ph, 1 spd., almond, 28lbs.

1-1/2 HP, WFK-6, TEFC, 3 ph., 1 spd., almond, 30lbs.

2 HP, WFK-8, TEFC, 3 ph., 1 spd., almond, 37 lbs.

3 HP, WFK-12, TEFC, 3 ph., 1 spd., almond, 35 lbs.

Not Shown

79129900 2-Speed Toggle Switch

350202 Seal Plate Kit: Seal plate (almond), Gasket (black),

with installed Seal (Includes items: 9, 16, & 18)

350203 Seal Plate Kit: Seal plate (black), Gasket (black), with

installed Seal (Includes items: 9, 16, & 18)

357244 Pot Assembly, Black NPT. (Includes items: 1-4, 10, 24

[qty. 2], 25 [qty. 2]).

357243 Pot Assembly, Almond NPT. (Includes items: 1-4, 10,

24 [qty. 2], 25 [qty. 2]).

WHISPERFLO® High Performance Pump Installation and User’s GuideWHISPERFLO® High Performance Pump Installation and User’s Guide

ENGLISH

ESPAÑOL

Curve Model

A WFDS-3, WFDS-24

B WFDS-4, WFDS-26

C WFDS-6, WFDS-28

D WFDS-8, WFDS-30

E WFE-2, WF-2, WF-23, WFK-2

F WFE-3, WFE-24, WF-3, WF-24,

WFK-3, WFDS-3, WFDS-24

G WFE-4, WFE-26, WF-4, WF-26,

WFK-4, WFDS-4, WFDS-26

H WFE-6, WFE-28, WF-6, WF-28,

WFK-6, WFDS-6, WFDS-28

I WFE-8, WFE-30, WF-8, WF-30,

WFK-8, WFDS-8, WFDS-30

J WFE-12, WF-12, WFK-12

Pump Performance Curves

075136 WFE-2

075137 WFE-3, WFE-24

075138 WFE-4, WFE-26

075139 WFE-6, WFE-28

075140 WFE-8, WFE-30

075141 WFE-12

075145 WFDS-3, WFDS-24

075142 WFDS-4, WFDS-26

075143 WFDS-6, WFDS-28

075144 WFDS-8, WFDS-30

075251 WF-2, WF-23

075252 WF-3, WF-24

075253 WF-4, WF-26

075254 WF-6,WF-28

075255 WF-8,WF-30

075256 WF-12

100

110

0102030405060708090100 110120 130140 150160 170180

TOTA L DYNAMIC HEAD IN FT OF WATER

WATER FLOW RATE IN US GALLONS PER MINUTE

WhisperFlo® High Performance Pump

WHISPERFLO®

GUÍA DE INSTALATIÓN

Y DEL USUARIO

BOMBA DE ALTO RENDIMIENTO

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

LEA Y SIGA TODAS LAS INSTRUCCIONES

GUARDE ESTAS INSTRUCCIONES

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

P/N 071109 Rev. J 8/29/14

previo aviso.

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

Todos los logotipos y las marcas comerciales de Pentair son propiedad de Pentair, Inc. Pentair Aquatic Systems™ , WhisperFlo® y

High Flow™ son marcas comerciales de Pentair Water Pool and Spa, Inc. y/o de sus compañías aﬁliadas en los Estados Unidos

y/o en otros países. A menos que se indique expresamente, los nombres y las marcas de terceros que se mencionan en este

documento no indican aﬁliación o aval alguno entre los propietarios de estos nombres y marcas y Pentair Water Pool and Spa,

Inc. Es posible que estos nombres y marcas sean marcas comerciales o registradas de estos terceros. Debido a que mejoramos

continuamente nuestros productos y servicios, Pentair se reserva el derecho a cambiar las especiﬁcaciones sin previo aviso.

Pentair es una compañía que ofrece igualdad de oportunidad de empleo.

ATENCIÓN AL CLIENTE / SOPORTE TÉCNICO

Si tiene alguna pregunta sobre cómo realizar pedidos de piezas de repuesto de Pentair Aquatic Systems, utilice la

siguiente información de contacto:

Servicio del Cliente y Soporte Técnico, USA

(de 8 a.m. a 4:30 p.m., Horario del Este y del Pacíﬁco)

Teléfono: (800) 831-7133

Fax: (800) 284-4151

Sitio web

Visite www.pentairpool.com o www.staritepool.com

para encontrar información sobre los productos

Pentair.

Sanford, Carolina del Norte

(de 8 a.m. a 4:30 p.m., Horario del Este)

Teléfono: (919) 566-8000

Fax: (919) 566-8920

Moorpark, California

(de 8 a.m. a 4:30 p.m., Horario del Pacíﬁco)

Teléfono: (805) 553-5000 (Ext. 5591)

Fax: (805) 553-5515

ÍNDICE

Important Pump Warning and

Safety Instructions ..............................................

Instalación ............................................................

Ubicación

Tuberías

Conexiones y válvulas

Instalación de cableado eléctrico

Mantenimiento ......................................................

Canastilla del ﬁltro de la bomba

Limpieza de la canastilla del ﬁltro de la bomba

Acondicionamiento para el invierno

Servicio .................................................................

Cuidado del motor

Reemplazo del sello del eje

Desarmado de la bomba

Rearmado de la bomba

Instrucciones para encender de nuevo

Imprimar la bomba

Localizador de averías .......................................

Curvas de la bomba

Piezas de reemplazo ...........................................

ENGLISH

ESPAÑOL

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

PELIGRO

LEA Y SIGA TODAS LAS INSTRUCCIONES

GUARDE ESTAS INSTRUCCIONES

Éste es el símbolo de alerta de seguridad.

Cuando vea este símbolo en su sistema o en este manual, busque

alguna de las siguientes palabras y esté alerta ante la posibilidad

de lesiones.

Advierte sobre peligros que pueden causar la muerte, lesiones

personales graves o daño a la propiedad si son ignorados.

Advierte sobre peligros que podrían causar la muerte, lesiones

personales graves o daño a la propiedad si son ignorados.

Advierte sobre los peligros que podrían o pueden causar lesiones

personales menores o daños a la propiedad

si son ignorados.

NOTA indica instrucciones especiales no relacionadas a peligros.

Lea cuidadosamente y siga las instrucciones de seguridad del equipo que aparecen

en este manual. Mantenga las etiquetas de seguridad en buen estado; reemplácelas

si faltan o están dañadas.

EL USO DE CUBIERTAS NO APROBADAS O PERMITIR EL USO DE UN SISTEMA DE

ACUICULTURA CUANDO FALTAN CUBIERTAS, SE ENCUENTRAN FRACTURADAS O

AVERIADAS PUEDE TENER COMO RESULTADO EL ATRAPAMIENTO DEL CUERPO

O DE UN MIEMBRO, ENREDO DEL CABELLO, ATRAPAMIENTO DEL CUERPO,

DESTRIPAMIENTO Y/O LA MUERTE.

La sección en el drenaje o salida puede causar:

Atrapamiento de miembros: Cuando se succiona un miembro o éste es insertado en una

apertura que tiene como resultado una obstrucción mecánica o hinchazón. Este riesgo

está presente cuando falta una cubierta del drenaje, o está rota, suelta, quebrada o no

está bien asegurada.

Enredo del cabello: Cuando el cabello se enreda o se anuda en la cubierta del drenaje,

atrapando al nadador debajo del agua. Este riesgo está presente cuando la velocidad del

ﬂujo de la cubierta es demasiado baja para la o las bombas.

Atrapamiento corporal: Cuando una porción del cuerpo queda contra la cubierta del

drenaje y atrapa al nadador debajo del agua. Este riesgo existe cuando falta la cubierta

del drenaje, cuando ésta está quebrada o cuando la velocidad de ﬂujo de la cubierta no

es lo suﬁcientemente alta para la o las bombas.

Destripamiento: Cuando una persona está sentada en una piscina abierta (especialmente

una piscina poco profunda para niños) o salida de un spa y se aplica la succión directamente

a los intestinos, causando un daño intestinal severo. Este riesgo está presente cuando falta

una cubierta del drenaje, o está suelta, quebrada o no está bien asegurada.

Atrapamiento mecánico: Cuando quedan atrapados en una entrada o en la cubierta del

drenaje objetos tales como: joyas, trajes de baño, accesorios para el cabello, dedos de la

mano o del pie o nudillos. Este riesgo está presente cuando falta la cubierta del drenaje,

o está rota, suelta, quebrada o no está bien asegurada.

NOTA: LA INSTALACIÓN DE PLOMERÍA DE SUCCIÓN DEBE SER INSTALADA DE

ACUERDO CON LOS CÓDIGOS, ESTÁNDARES Y PAUTAS NACIONALES Y LOCALES

MÁS ACTUALIZADOS.

LA BOMBA PRODUCE ALTOS NIVELES DE SUCCIÓN Y CREA UN FUERTE VACÍO EN

EL DRENAJE PRINCIPAL EN LA BASE DEL CUERPO DE AGUA. ESTA SUCCIÓN ES

TAN FUERTE QUE PUEDE ATRAPAR A ADULTOS O NIÑOS DEBAJO DEL AGUA SI SE

ACERCAN DEMASIADO AL DRENAJE O SI HAY ALGUNA PARTE DE LA CUBIERTA O

PARRILLA DEL DRENAJE SUELTA O AVERIADA.

PELIGRO

PELIGRO DE TRAMPA DE SUCCIÓN: ¡MANTÉNGASE

ALEJADO DEL DRENAJE PRINCIPAL Y DE TODAS LAS

SALIDAS DE SUCCIÓN!

PELIGRO

SI NO SE RESPETAN TODAS LAS INSTRUCCIONES Y

ADVERTENCIAS LAS CONSECUENCIAS PUEDEN SER

HERIDAS GRAVES O LA MUERTE. LA BOMBA DEBE SER INSTALADA Y REVISADA

ÚNICAMENTE POR UN PROFESIONAL DE SERVICIO DE PISCINAS CALIFICADO.

LOS INSTALADORES, OPERADORES Y PROPIETARIOS DE LAS PISCINAS DEBEN

LEER ESTAS ADVERTENCIAS Y TODAS LAS INSTRUCCIONES QUE APARECEN

EN EL MANUAL DEL PROPIETARIO ANTES DE UTILIZAR ESTA BOMBA. ESTAS

ADVERTENCIAS Y EL MANUAL DEL PROPIETARIO DEBEN PERMANECER CON EL

PROPIETARIO DE LA PISCINA.

Advertencias generales

• Nunca abra el interior de la caja del motor. Hay un banco capacitor que admite una

carga de hasta 230 VCA incluso cuando la unidad no tenga energía eléctrica.

• La bomba del spa no es sumergible.

• La bomba puede trabajar con ﬂujos máximos altos; tenga cuidado cuando realice la

instalación y programación para limitar el potencial de rendimiento de las bombas

con equipos antiguos o de origen desconocido.

• Los requisitos de códigos para la conexión eléctrica diﬁeren de un estado a otro.

Instale los equipos de acuerdo con el Código Eléctrico Nacional y todos los códigos

y ordenanzas locales aplicables.

Conecte sólo a un circuito eléctrico protegido por un interruptor

de circuito con descarga a tierra (GFCI). Este GCFI debe

ser provisto por el instalador y debe ser probado de manera rutinaria. Para probar el

GFCI presione el botón de prueba. El GFCI debería interrumpir la energía eléctrica.

Presione el botón de reinicio. Debería restaurar la energía. Si el GFCI no funciona de

esta manera, el GFCI tiene una falla. Si el GFCI interrumpe la energía a la bomba sin

que se presione el botón de prueba, hay presencia de corriente de tierra, indicando

la posibilidad de un choque eléctrico. No utilice esta bomba. Desconecte la bomba y

haga que un representante de servicio técnico caliﬁcado corrija el problema antes de

utilizar el equipo.

Riesgo de choque eléctrico. Conecte sólo a un circuito

eléctrico protegido por un interruptor de circuito con descarga

a tierra (GFCI). Comuníquese con un electricista caliﬁcado si no puede veriﬁcar que el

circuito esté protegido por un interruptor GFCI.

No permita que los niños utilicen este producto.

Cuando instale y utilice este equipo eléctrico, siempre debe respetar precauciones de

seguridad básicas, incluyendo las siguientes:

INSTRUCCIONES Y ADVERTENCIAS DE SEGURIDAD IMPORTANTES DE LA BOMBA

Nota Importante:

Atención Instalador: Esta guía contiene información importante sobre

la instalación, el funcionamiento y el uso seguro de este producto. Esta

información debe ser entregada al propietario y/o al operador de este equipo

después de la instalación del limpiador de piscina. Atención Usuario: Este

manual contiene información importante que le ayudará a utilizar y mantener

este limpiador.

Esta bomba se utiliza para piscinas permanentes y también

puede ser utilizada en jacuzzis o spa si está indicado.

No la utilice con piscinas desmontables. Una piscina con instalación permanente

es una piscina construida en el suelo o en una base de manera que no puede

ser desmontada. Una piscina desmontable está construida de manera que puede

ser fácilmente desmontable para su almacenamiento y rearmada de acuerdo

a su formato original.

• Antes de realizarle el servicio técnico a la bomba, APAGUE la energía a la bomba

desconectando el circuito principal a la bomba.

• Este dispositivo no debe ser utilizado por personas (incluidos niños) con capacidades

físicas, sensoriales o mentales reducidas, o falta de experiencia y conocimiento,

a menos que hayan recibido instrucciones y sean supervisados por una persona

responsable por su seguridad.

• Para cada drenaje debe utilizarse una cubierta de succión anti-atrapamiento

aprobada de acuerdo a ANSI/ASME A112.19.8 que debe estar correctamente

instalada y asegurada.

• Cada cubierta de succión debe estar instalada al menos a tres pies (0,9 m) de

distancia, medidos entre los 2 puntos más cercanos.

• Inspecciones regularmente todas las cubiertas para controlar que no existan

quebraduras, daños o erosión por exposición a la intemperie.

• Si falta una cubierta o si ésta se aﬂoja, quiebra, daña o rompe, reemplácela

con una cubierta certiﬁcada adecuada.

• Reemplace las cubiertas de drenaje cuando sea necesario. Las cubiertas de

drenaje se deterioran con el tiempo debido a la exposición al sol y a la intemperie.

• Evite que el cabello, los miembros o el cuerpo estén próximos a cualquier

cubierta de succión, drenaje de la piscina o salida.

• Desactive las salidas de succión reconﬁgure las entradas de retorno.

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

Pentair Water Pool and Spa®

IMPORTANT SAFETY INSTRUCTIONS

For Installation of Electrical Controls at Equipment Pad

(ON/OFF Switches, Timers and Automation Load Center)

Install all electrical controls at equipment pad, such as on/off

switches, timers, and control systems, etc. to allow the

operation (startup, shut-down, or servicing) of any pump or

filter so the user does not place any portion of his/her body

over or near the pump strainer lid, filter lid or valve closures.

This installation should allow the user enough space to stand

clear of the filter and pump during system start-up, shut down

or servicing of the system filter.

PELIGRO

Pentair Water Pool and Spa®

IMPORTANT SAFETY INSTRUCTIONS

For Installation of Electrical Controls at Equipment Pad

(ON/OFF Switches, Timers and Automation Load Center)

Install all electrical controls at equipment pad, such as on/off

switches, timers, and control systems, etc. to allow the

operation (startup, shut-down, or servicing) of any pump or

filter so the user does not place any portion of his/her body

over or near the pump strainer lid, filter lid or valve closures.

This installation should allow the user enough space to stand

clear of the filter and pump during system start-up, shut down

or servicing of the system filter.

GUARDE ESTAS INSTRUCCIONES

La bomba puede producir niveles altos de succión dentro del

lado de succión del sistema de plomería.

Estos altos niveles de succión pueden implicar un riesgo si una persona se acerca

demasiado a los oriﬁcios de succión. Este alto nivel de vacío puede causar daños

severos en personas, quienes también podrían quedar atrapadas y ahogarse. Es de

primordial importancia que el sistema de plomería sea instalado de acuerdo a los más

recientes códigos nacionales y locales para las aplicaciones de piscinas.

Las bombas de tamaño incorrecto o instaladas de manera

incorrecta o utilizadas en aplicaciones diferentes a aquellas

para las cuales la bomba fue diseñada pueden tener como resultado daños personales

severos o la muerte. Estos riesgos incluyen pero no se limitan a choque eléctrico,

incendio, inundación, succión, atrapamiento, lesiones graves o daño a la propiedad

causados por una falla estructural de la bomba u otro componente del sistema.

Información general para la instalación

• La instalación y el servicio deben ser efectuados por un profesional de servicio caliﬁcado,

y deben cumplir con todos los códigos nacionales, estatales y locales.

• En la instalación se debe colocar un drenaje en el compartimiento para los componentes

eléctricos.

• Estas instrucciones contienen información para una variedad de modelos de bombas y

por lo tanto algunas instrucciones pueden no aplicarse a un modelo especíﬁco. Todos

los modelos deben ser utilizados en aplicaciones de piscinas. La bomba funcionará

correctamente sólo si tiene el tamaño adecuado para la aplicación especíﬁca y si está

correctamente instalada.

Antes de realizar el servicio al equipo, tome nota de la presión del ﬁltro. Asegúrese de

que se realicen todos los controles para asegurar que el sistema no arranque sin aviso

durante el servicio técnico. Desconecte la energía a la bomba. IMPORTANTE: Coloque

la válvula de alivio de aire manual del ﬁltro en posición abierta y espere que se

libere la presión del sistema.

Antes de iniciar el sistema, abra totalmente la válvula de liberación de aire manual y

ubique todas las válvulas del sistema en posición "abierto" para permitir que el agua

ﬂuya libremente desde y hacia el tanque. Aléjese de los equipos y arranque la bomba.

IMPORTANTE: No cierre la válvula de alivio de aire manual del ﬁltro hasta que se

haya descargado la totalidad de la presión de la válvula y aparezca un chorro de

agua constante. Observe el indicador de presión del ﬁltro y asegúrese de que no es más

alto que el estado anterior al servicio.

PRESIÓN PELIGROSA: MANTÉNGASE ALEJADO

DE LA BOMBA Y FILTRO DURANTE EL ARRANQUE

Los sistemas de circulación operan bajo alta presión. Cuando

cualquier parte del sistema de circulación (es decir anillo de

seguridad, bomba, ﬁltro y válvulas, etc) está siendo controlado

por el servicio técnico, es posible que ingrese aire al sistema y

que éste se presurice.

El aire presurizado puede provocar que las válvulas y la tapa del ﬁltro de la cubierta

de la caja de la bomba se separen violentamente lo cual puede tener como resultado

lesiones graves o la muerte. La tapa del tanque del ﬁltro y la cubierta del ﬁltro deben estar

correctamente aseguradas para evitar una separación violenta. Manténgase alejado del

equipo del sistema de circulación cuando encienda o arranque la bomba.

Instale todos los controles eléctricos en la superﬁcie de

apoyo del equipo, como interruptores de encendido/

apagado y sistemas de control, etc. para permitir el

funcionamiento (arranque, apagado o servicio) de cualquier

bomba o filtro de manera que el usuario no coloque

ninguna porción de su cuerpo por encima o cerca de la

tapa del ﬁltro de la bomba, la tapa del ﬁltro o el cierre de

la válvula. Esta instalación debería permitirle al usuario

utilizar espacio suﬁciente para permanecer alejado del

ﬁltro y la bomba durante el arranque, apagado o servicio

del ﬁltro del sistema.

Para la instalación de controles eléctricos en la superﬁcie de apoyo del equipo

(interruptores ENCENDIDO/APAGADO, relojes o centro de carga automática)

La ley de seguridad para piscinas y spa Virginia Graeme Baker (VGB) crea nuevos

requisitos para los dueños y operadores de piscinas y spa comerciales.

Las piscinas y spa comerciales construidos después del 19 de diciembre de 2008

deben utilizar:

(A) Un sistema de drenaje principal múltiple sin aislación con cubiertas de salida de

succión que cumplan con las características ASME/ANSI A112.19.8a para accesorios

de succión en piscinas, piscinas poco profundas para niños, spas y jacuzzis ya sea:

(i) Un sistema de seguridad de alivio de vacío (SVRS) que cumpla con la normativa

ASME/ANSI A112.19.17 Manufactured Safety Vacuum Release systems (SVRS)

para sistemas de succión en piscinas residenciales y comerciales, spa, jacuzzis y

piscinas poco profundas para niños, y/o especiﬁcaciones estándar ASTM F2387 para

Manufactured Safety Vacuum Release Systems (SVRS) en piscinas, spa y jacuzzis o

(ii) un sistema de ventilación bien diseñado y con un sistema probado de limitación

de succión

(iii) un sistema de apagado automático de bomba

Las piscinas o spa comerciales construidos con anterioridad al 19 de diciembre de

2008 con una salida de succión sumergida deben utilizar una salida de succión que

cumpla con ASME/ANSI A112.19.8a y:

(A) un SVRS que cumpla con los requisitos ASME/ANSI A112.19.17 y/o ASTM

F2387, o bien

(ii) un sistema de ventilación bien diseñado y con un sistema probado de limitación

de succión o bien

(iii) un sistema de apagado automático de bomba, o

(D) salidas sumergidas desactivadas, o

(E) Salidas de succión que deben ser reconﬁguradas como entradas de retorno.

Antes de instalar este producto, lea y siga todas las advertencias e instruc-

ciones incluidas. Llame al (800) 831-7133 para obtener copias adicionales de

estas instrucciones sin costo.

Instrucciones y advertencias de seguridad y

la versión en español de este manual

del producto, se puede encontrar en línea a:

http://www.pentairpool.com/es/pool-owner/manuals/ o llame al (800)

831-7133 para obtener copias adicionales de estas instrucciones sin costo.

Debe existir un interruptor de emergencia para la bomba en

un lugar fácilmente accesible y visible. Asegúrese que de los

usuarios conozcan dónde está y sepan cómo usarla en caso

de emergencia.

• Para cada drenaje debe utilizarse una cubierta de succión anti-atrapamiento

aprobada de acuerdo a ANSI/ASME A112.19.8 que debe estar correctamente

instalada y asegurada.

• Cada cubierta de succión debe estar instalada al menos a tres pies (0,9 m) de

distancia, medidos entre los 2 puntos más cercanos.

• Inspecciones regularmente todas las cubiertas para controlar que no existan

quebraduras, daños o erosión por exposición a la intemperie.

• Si falta una cubierta o si ésta se aﬂoja, quiebra, daña o rompe, reemplácela

con una cubierta certiﬁcada adecuada.

• Reemplace las cubiertas de drenaje cuando sea necesario. Las cubiertas de

drenaje se deterioran con el tiempo debido a la exposición al sol y a la intemperie.

• Evite que el cabello, los miembros o el cuerpo estén próximos a cualquier

cubierta de succión, drenaje de la piscina o salida.

• Desactive las salidas de succión reconﬁgure las entradas de retorno.

PARA MINIMIZAR EL RIESGO DE LESIONES DEBIDO

AL PELIGRO DE ATRAPAMIENTO POR SUCCIÓN:

INSTRUCCIONES Y ADVERTENCIAS DE SEGURIDAD IMPORTANTES DE LA BOMBA

ENGLISH

ESPAÑOL

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

Sólo personal de servicio caliﬁcado debe instalar la bomba WhisperFlo®. Consulte la sección “Instrucciones de seguridad

y advertencias de la bomba” en las páginas 11 a 12 para obtener información adicional sobre pautas para la instalación

y la seguridad.

INSTALACIÓN

Tuberías

1. P

ara una mejor plomería en la piscina, se recomienda

utilizar un tamaño de tubería más grande. Cuando

instale los accesorios para entradas y salidas

(adaptadores macho), use un sellador de roscas.

2. Utilice tamaños de caños más grandes para una mejor

tubería. El diámetro de empalme debe ser el mismo o

mayor que el diámetro de la línea de retorno.

3. Las tuberías en el lado de succión de la bomba deben

ser lo más cortas posibles.

4. Se recomienda una válvula, codo o pieza en forma de

T en la línea de succión no debería estar más cerca

al frente de la bomba que cinco veces el diámetro de

la tubería de la línea de succión (es decir, una tubería

de 2 pulgadas (5,1 cm) necesita un espacio recto

enfrente de la entrada de succión de la bomba de 10

pulgadas (254 mm)). Esto ayudará a que el cebado

de la bomba sea más rápido y dure por más tiempo.

Conexiones y Válvulas

1. No instale codos de 90° directamente en la entrada

de la bomba.

2. L

os sistemas de succión deberían tener válvulas de

compuertas instaladas en las tuberías de succión y

descarga para mantenimiento; sin embargo, la válvula

de compuerta de succión no debe estar más cerca

que cinco veces el diámetro de la tubería de succión

como se describe en el párrafo anterior.

3. Utilice una válvula de retención en la línea de

descarga al utilizar esta bomba para cualquier

aplicación donde hay altura signiﬁcativa de la tubería

después de la bomba.

4. Asegúrese de instalar las válvulas de comprobación

cuando nivela en paralelo con otra bomba. Esto ayuda

a evitar la rotación inversa del propulsor y el motor.

Ubicación

1. Instale la bomba lo más cerca posible a la piscina o

spa. Para reducir la pérdida de fricción y mejorar la

eﬁcacia, use un mecanismo de succión corta y directa

y retornos de tuberías.

2. Realice la instalación a un mínimo de 5 pies (1,52 m.)

de la pared interior de la piscina y el spa. En Canadá,

las instalaciones deben estar como mínimo a una

distancia de 9,8 pies (3 metros) del agua de la piscina.

3. Instale la bomba a un mínimo de 3 pies (0,9 metros)

de la salida del calefactor.

4. No instale la bomba a más de 10 pies (2,44 m) por

encima del nivel del agua.

5. Instale la bomba en un área cubierta y bien ventilada

para protegerla de la humedad excesiva (es decir,

lluvia, sistemas de aspersión, etc.)

6. Para jacuzzis y spas, no instale dentro de una caja

exterior o debajo de la base de un jacuzzi o spa.

7. Instale la bomba con una distancia de separación

trasera de al menos 3 pulgadas (76,2 mm) de

manera que el motor pueda ser extraído fácilmente

cuando debe ser reparado y cuando se realice el

mantenimiento.

DIÁMETRO DE EMPALME DE 5 x

CODO

DISTANCIA DE SEGURIDAD

TRASERA DE 3 PULGADAS

(76,2 CM) MÍNIMO

3 PULG.

DE MÍNIMO

Recomendado mínimo Diámetro de empalme

Distancia de seguridad de la parte trasera

de la bomba

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

Instalación de cableado eléctrico

ENGLISH

ESPAÑOL

Tornillo de

tierra screw

Nota: Cuando la bomba se monta permanente-

mente dentro de 5 pies (1.524 m) de las paredes

interiores de una piscina, tiene que usar un No.

8 AWG o conductor más grande para conectar

al tirón de conductor que pega.

1. Asegúrese de que todos los interruptores y

conmutadores eléctricos estén apagados antes de

cablear el motor.

2. Asegúrese de que el voltaje de la línea de suministro

coincida con el voltaje del motor descrito en la placa

del motor (por ejemplo, 230 VCA o 115 VCA). Si no

coinciden, puede ocurrir un daño permanente al

motor.

3. Utilice el alivio de tensión y asegúrese de que todas

las conexiones eléctricas estén limpias y ajustadas.

4. Corte los cables en la longitud adecuada, de modo

de que no se superpongan o toquen cuando estén

conectados.

5. Conecte el motor a tierra de manera permanente

utilizando el cable a tierra verde, como se muestra a

continuación. Utilice el tamaño y tipo de cable correcto

especiﬁcado por el Código Eléctrico Nacional.

Asegúrese de que el cable a tierra esté conectado

a una conexión a tierra de servicio eléctrico.

6. Una el motor a la estructura conforme lo estable el

Código Eléctrico Nacional. UL requiere el uso de un

conductor de interconexión de cobre sólido de un

diámetro mínimo de 8 AWG. Pase un cable desde

el tornillo o terminal de interconexión externa hasta

la estructura de interconexión.

7. Conecte el cable desde el conector de cable accesible

en el motor hasta todas las partes metálicas de

la estructura y todo el equipo eléctrico, conducto

metálico y tubería metálica a 5 pies (1,5 m) de las

paredes internas de la estructura. Para Canadá, se

requiere un conductor de interconexión de cobre

sólido de 6 AWG o más largo.

8. La bomba debe conectarse de manera permanente

ya sea a un interruptor de circuito, reloj o relé de

2 polos. Si se suministra energía CA a través de un

interruptor de circuito GFCI, utilice un interruptor de

circuito especial que no posea otras cargas eléctricas.

Nota: Cuando la bomba se arranca y detiene

al desconectar la energía mediante un relé o

reloj, se debe utilizar un dispositivo de dos polos

para aplicar y desconectar la energía de las dos

TERMINALES DE LÍNEA DE ENERGÍA.

RIESGO DE CHOQUE ELÉCTRICO O ELECTROCUCIÓN. Esta bomba debe ser instalada por un electricista autorizado o

matriculado o un profesional de servicio caliﬁcado de acuerdo con el Código Eléctrico Nacional y todos los códigos y ordenanzas

locales aplicables. Una instalación inadecuada generará un riesgo eléctrico que puede ocasionar la muerte o lesiones graves a

los usuarios, los instaladores u otras personas debido a un choque eléctrico, y también puede provocar daños a la propiedad.

Siempre desconecte la energía eléctrica a la bomba en el interruptor de circuito antes de realizar el servicio de la bomba.

Si no se hace esto, las personas que realizan el servicio, los usuarios u otras personas pueden resultar muertas o con

heridas de gravedad debido al electrochoque.

Lea todas las instrucciones de servicio antes de comenzar a trabajar en la bomba.

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

MANTENIMIENTO

Canastilla del ﬁltro de la bomba

La canastilla del ﬁltro (o "depósito del ﬁltro") se encuentra

enfrente del alojamiento de la bomba. La canastilla del

ﬁltro debe mantenerse limpia y sin suciedad. Inspeccione

la canastilla a través de la tapa en la parte superior del

alojamiento.

Asegúrese de inspeccionar visualmente la canastilla del

ﬁltro cada 1 a 4 semanas. Las canastillas del ﬁltro sucias

reducen la eﬁciencia del ﬁltro y del calefactor y ejercen

una presión anormal sobre el motor de la bomba. La

acumulación de bacterias puede ensuciar la tapa.

Limpieza de la canastilla del ﬁltro de la bomba

1. Apague la bomba en el interruptor de circuito.

2. Libere presión en el sistema.

3. Gire la tapa y abrazadera en el sentido contrario a las

agujas del reloj y retírelas de la bomba.

4. Retire los residuos y limpie la canastilla. Reemplace la

canastilla si está rajada.

5. Vuelva a colocar la canastilla en la caja. Asegúrese de

alinear la perforación en la parte inferior de la canastilla

con el acanalado en la parte inferior del alojamiento.

6. Llene el depósito y el alojamiento de la bomba hasta

el puerto de entrada con agua.

7. Limpie la tapa y la abrazadera, el anillo tórico y la

superﬁcie de sellado del depósito de la bomba.

Nota: Es importante que mantenga el anillo tórico de

la tapa limpio y bien lubricado.

8. Vuelva a instalar la tapa colocando la abrazadera y la

tapa en el depósito. Asegúrese de que el anillo tórico

de la tapa esté bien colocado.

Coloque la abrazadera y la tapa sobre la bomba, luego

gire en sentido de las agujas del reloj hasta que las

manijas del anillo de seguridad estén horizontales.

9. Encienda la bomba en el interruptor de circuito.

10. Abra la válvula de alivio de aire manual en la parte

superior del ﬁltro. Aléjese del ﬁltro.

11. Espere hasta que se libere toda la presión. Ponga en

marcha la bomba.

12. Purgue el aire del ﬁltro hasta que un ﬂujo constante

de agua salga de la válvula de alivio de aire del ﬁltro.

Cierre la válvula de alivio de aire manual.

NO abra el depósito del ﬁltro si el cebado de la bomba falla o si la bomba ha estado funcionando sin agua en el depósito del ﬁltro.

Las bombas que funcionan en estas circunstancias pueden experimentar una acumulación de presión de vapor y pueden contener

agua caliente escaldada. Si abre la bomba puede resultar herido de gravedad. Para evitar la posibilidad de lesiones personales,

asegúrese de que las válvulas de succión y descarga estén abiertas y la temperatura del depósito del ﬁltro esté fría para el tacto,

luego ábrala con extrema precaución.

Para evitar el daño de la bomba y para un adecuado funcionamiento del sistema, limpie el ﬁltro de la bomba y las canastillas de

los desnatadores con regularidad.

Nota: No envuelva el motor con plástico u otros materiales

hermetizados durante el almacenamiento de invierno.

El motor puede estar cubierto durante una tormenta, el

almacenamiento de invierno, etc., pero nunca cuando esté

funcionando o se espere que comience a funcionar.

Acondicionamiento para el invierno

• En áreas de clima templado, en caso de condiciones

temporales de congelamiento, haga funcionar su

equipo de ﬁltración toda la noche para evitar el

congelamiento.

• Usted es responsable de determinar cuándo

pueden ocurrir condiciones de congelamiento. Si

se esperan condiciones de congelamiento, siga los

siguientes pasos para reducir el riesgo de daño por

congelamiento. El daño por congelamiento no se

encuentra cubierto por la garantía.

Para evitar el daño por congelamiento, siga las

instrucciones a continuación:

1. Apague el suministro eléctrico de la bomba en el

interruptor de circuito.

2. Drene el agua de la caja de la bomba retirando los dos

tapones de drenaje de la tapa. Guarde los tapones en

la canastilla de la bomba.

3. Cubra el motor para protegerlo de la lluvia fuerte, la

nieve o el hielo.

ESTE SISTEMA OPERA BAJO ALTA PRESIÓN.

Cuando cualquier parte del sistema de circulación (es decir

anillo de seguridad, bomba, ﬁltro, válvulas, etc.) está siendo

controlado por el servicio técnico, es posible que ingrese aire

al sistema y que éste se presurice. El aire presurizado puede

Abrazadera, depósito

Anillo tórico

Tapa

Canastilla del ﬁltro

Depósito

Tapón para

drenajes

Alojamiento

Conjunto del depósito del ﬁltro

causar que la tapa se separe, lo que puede provocar heridas graves, la muerte

o daño a la propiedad. A ﬁn de evitar este riesgo potencial, siga las instrucciones

que se mencionan arriba.

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

Cuidado del motor

Protéjalo del calor

1. Cubra el motor del sol.

2. Cualquier caja del motor debe estar bien ventilada para

evitar el sobrecalentamiento.

3. Proporcione amplia ventilación cruzada.

Protéjalo contra la suciedad.

1. Protéjalo contra cualquier materia extraña o salpicadura

de agua.

2. No almacene (o derrame) químicos sobre o cerca del

motor.

3. Protéjalo contra cualquier materia extraña o salpicadura

de agua.

4. Evite barrer o levantar polvo cerca del motor mientras

está en funcionamiento.

5. Si un motor se daña por suciedad, la garantía del motor

se anula.

6. Limpie la tapa y la abrazadera, el anillo tórico y la

superﬁcie de sellado del depósito de la bomba.

Protéjalo contra la humedad

1. Protéjalo contra las salpicaduras o pulverizaciones de

agua.

2. Protéjalo de las temperaturas extremas.

3. Protéjalo contra cualquier materia extraña o salpicadura

de agua.

4. Si un motor se moja, déjelo secar antes de ponerlo en

funcionamiento. No permita que la bomba funcione si

se ha inundado.

5. Si un motor se daña por agua, la garantía del motor se

anula.

SERVICIO

ENGLISH

ESPAÑOL

Nota: Cuando está reemplazando el motor,

asegúrese que el soporte de motor está colocado

correctamente para soportar el tamaño del motor

que se está instalando.

Desmontaje de bomba

Todas piezas móviles se encuentran en el montaje de

abajo por atrás de esta bomba.

Herramientas requeridas:

• 3/ Llave de boca de 3/32 pulgada (.2381 cm)

• 1/Llave de boca de 1/2 pulgada (15.24 cm).

• 9/Llave de boca de 9/16 pulgada (1.429 cm).

• F Destornillador con cabeza plana.

Para quitar y reparar el montaje de abajo del motor

ejecute los siguientes procedimientos.

1. Apague el cortacircuito de bomba en el panel

principal.

2. Vacíe la bomba al quitar los tapones de drenaje.

3. Quite los 6 pernos que sujetan el cuerpo de bomba

principal (olla de colador/voluta) al montaje de

abajo por atrás.

4. SUAVEMENTE separe las dos mitades de bomba,

quitando el montaje de abajo por atrás.

5. Use una llave de boca de 3/32 pulgada (.2381 cm)

para desapretar los dos tornillos que soportan y

que se encuentran en el difusor.

6. Mantenga el impulsor seguramente en lugar y

quite el tornillo de llave del impulsor al usar un

desarmador (desatornillador) de cruz. Este tornillo

tiene rosca a mano izquierda y se desaprieta en el

sentido de las agujas del reloj.

7. Quite la tapa del eje que se encuentra en la parte

de atrás del motor y mantenga el eje seguro con

una llave de boca de 1/2 pulgada (15.24 cm).

8. Para destornillar el impulsor del eje, déle vuelta al

impulsor en el sentido opuesto de las agujas del

reloj.

9. Quite los cuatro pernos de la placa de sello al

motor, usando una llave de 9/16 pulgada (1.429

cm).

El sello de eje

El sello de eje consiste principalmente en dos piezas, un

miembro rotativo y un sello cerámico. La bomba requiere

de poco o de ningún mantenimiento además de atención

razonable, sin embargo, podría ser que de vez en cuando

se dañe el sello de eje y tenga que reemplazarse.

Nota: Las caras pulidas y labradas del sello se pueden

dañar si no se usa con cuidado.

Siempre desconecte la energía hacia la bomba en el interruptor de circuito antes de realizar el servicio a la bomba. Si no se hace

esto, las personas que realizan el servicio, los usuarios u otras personas pueden resultar muertas o con heridas de gravedad debido

al electrochoque. Lea todas las instrucciones de servicio antes de comenzar a trabajar en la bomba.

NO abra el depósito del ﬁltro si el cebado de la bomba falla o si la bomba ha estado funcionando sin agua en el depósito del ﬁltro.

Las bombas que funcionan en estas circunstancias pueden experimentar una acumulación de presión de vapor y pueden contener

agua caliente escaldada. Si abre la bomba puede resultar herido de gravedad. Para evitar la posibilidad de lesiones personales,

asegúrese de que las válvulas de succión y descarga estén abiertas y la temperatura del depósito del ﬁltro esté fría para el tacto,

luego ábrala con extrema precaución.

Asegúrese de no rayar o marcar las caras pulidas del sello del eje; el sello perderá si las caras se encuentran dañadas. Las caras

pulidas y recubiertas del sello se podrían dañar si no son tratadas con cuidado.

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

Armar la bomba de nuevo

1. Cuando este instalando el sello mecánico de

la ﬂecha, use un sellador de silicón en la parte

metálica de la ﬂecha antes de presionar contra

la placa de sello, y teniendo mucho cuidado de

mantener el sellador de silicón alejado del la cara

de sellado de la bomba. Asegúrese que el sello se

encuentre completamente asentado y deje pasar

24 horas para permitir que el sellador seque. (Kid

de remplazo completo con la placa de sello y el sello

mecánico esta disponible, P/N 350201/350101.)

2. Antes de instalar la sección cerámica del sello en

el impulsor, asegúrese que el impulsor está limpio.

Use un jabón de poca densidad y agua para sellar

el sello. Empuje el sello en el impulsor con los

dedos gordos y pase un paño para limpiar las caras

cerámicas y de carbón.

3. Reinstalar de nuevo la placa de sello al motor.

Ajustando los Pernos, 3/8-16 x 7/8 (2,22 cm)

de cabeza hexagonal, a un torque de 7,91 Nm

de manera cruzada (apretar uno de los pernos

y después apretar el perno opuesto y repita la

misma secuencia hasta que todos los pernos estén

ajustados al torque requerido).

4. Limpie la rosca de la ﬂecha y la rosca del impulsor,

después enrosque el impulsor a la ﬂecha del motor.

5. Atornille el tornillo de cierre del impulsor (en

el sentido opuesto de las agujas del reloj para

apretar).

6. Monte de nuevo el difusor en la placa de sello.

Asegúrese que las clavijas plásticas y las

inserciones de tornillos de mantener están alineado.

7. Engrase el anillo en O del difusor y empaque de

placa de sello o el anillo en O antes de armar de

nuevo.

8. Engrase las roscas de perno, arme el montaje de

abajo del motor al cuerpo de olla de colar y bomba al

usar los dos pernos que corren a través para tener

alineamiento adecuado. Colocar los Pernos, 3/8

-16 x 2 de cabeza hexagonal 18-8 acero inoxidable

(se requieren 2) a través de la placa de sellado y

la voluta y no los ajuste hasta que los Pernos de

3/8, 16 x 1-1/4 (3,18 cm) cabeza hexagonal 18-8

acero inoxidable (se requieren 4) estén ajustados

a mano. Ajustar todos los pernos a un torque de

12,43 Nm, de manera cruzada.

9. Llene la bomba con agua.

10. Instale de nuevo la tapa de bomba y abrazadera

plástica; vea INSTRUCCIONES PARA ENCENDER

DE NUEVO.

11. Prepare de nuevo el sistema.

Instrucciones para encender de nuevo

Si se instala la bomba debajo del nivel de agua en la

piscina, cierre las líneas de regreso y de aspiración antes

de abrir la olla de pelo y pelusa en la bomba. Asegúrese

de abrir de nuevo las válvulas antes de usar.

Imprimar la bomba

La olla de colador de bomba tiene que llenarse con agua

antes de que se empiece la bomba incialmente. Siga

estos pasos para imprimar la bomba.

1. Quite la abrazadera plástica de la tapa de la bomba.

Quite la tapa de la bomba.

2. Llene la olla de colador de bomba con agua.

3. Arme de nuevo el cubierto de bomba y abrazadera

plástica en la olla de colador. Ahora la bomba está

lista para imprimar.

4. Abra válvula de escape de aire en el ﬁltro y

manténgase a distancia del ﬁltro.

5. Encienda el interruptor o reloj.

6. Cuando agua sale de la válvula de escape de aire,

cierre la válvula. Este sistema ahora debe estar

libre de aire y circulando agua de nuevo a la piscina

y de vuelta.

7. Para bomba de 2 velocidades:

8. La bomba debe funcionar en alta velocidad para

imprimar.

9. La bomba no debe funcionar por más de 8 minutos

antes de que se logre imprimar.

NO haga funcionar la bomba en seco. Si hace funcionar la bomba en seco, el sello mecánico se dañará y la bomba comenzará a perder. Si esto

ocurre, deberá cambiar el sello dañado. SIEMPRE mantenga el nivel de agua adecuado. Si el nivel de agua cae por debajo del puerto de succión,

la bomba extraerá aire del puerto de succión, perderá cebado y funcionará en seco, lo que dañará el sello. El funcionamiento continuo en este

estado puede causar una pérdida de presión, lo que dañará la caja de la bomba, el propulsor y sello y puede provocar la pérdida de propiedad y

lesiones personales.

EJE DE MOTOR

PERNO

PLACA DEL SELLO

TORNILLO DE FIJACIÓN

SELLO DE TORNILLO

DE FIJACIÓN

PROPULSOR

BRIDA DE PLACA

DE SELLO

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

LOCALIZADOR DE AVERÍAS

Problema Posible causa Medida correctiva

Si la bomba falla. La bomba no imprima – demasiado aire.

La bomba no imprima—no hay agua suﬁciente

El colador de bomba está atascado

Empaque de colador de bomba defectuoso.

Revise la tubería de succión y las prensastopas en cualquier

válvulas de puerta de aspiración. Cierre la tapa en la olla de

coladora de bomba y asegúrese que el empaque de tapa

está en lugar.Revise el nivel de agua para asegurarse que la

desnatadora no está jalando aire.

Asegúrese que las líneas de aspiración, el colador de bomba,

y la voluta de bomba están llenas con agua.

Asegúrese que la válvula en la línea de aspiración está

funcionando y abierta, (algunos sistemas no tienen válvulas).

Revise el nivel de agua para asegurarse que hay agua disponible

a través de la desnatadora.

Limpie la olla de coladora de bomba.

Reemplazar empaque.

Capacidad reducida y/o

presión baja de agua.

Bolsas de aire o fugas en la línea de aspiración.

Impulsor atascado.

Colador de bomba atascado.

Revise la tubería de succión y las prensastopas en cualquier

válvulas de puerta de aspiración. Cierre la tapa en la olla de

coladora de bomba y asegúrese que el empaque de tapa

está en lugar.Revise el nivel de agua para asegurarse que la

desnatadora no está jalando aire.

Apague la energía eléctrica en los interruptores de circuito

de la bomba.

Desensamblar (Referir a Desensamblaje de la bomba, página

16).

Remover la basura del impulsor, si la basura no pueden ser

removida por complete, siga las siguientes instrucciones:

1. Remueva el Tornillo de 1/4, 20x1, LH, Phillips MS 18-8 de

acero inoxidable y la arandela de goma del impulsor.

2. Remueva el impulsor, termine de limpiarlo y vuelva a

instalar.

Reensamblar (Referir a Armar la bomba de nuevo, página 17).

Limpie el depósito de aspiración.

ENGLISH

ESPAÑOL

Curva Modelo

A WFDS-3, WFDS-24

B WFDS-4, WFDS-26

C WFDS-6, WFDS-28

D WFDS-8, WFDS-30

E WFE-2, WF-2, WF-23, WFK-2

F WFE-3, WFE-24, WF-3, WF-24, WFK-

3, WFDS-3, WFDS-24

G WFE-4, WFE-26, WF-4, WF-26, WFK-

4, WFDS-4, WFDS-26

H WFE-6, WFE-28, WF-6, WF-28, WFK-

6, WFDS-6, WFDS-28

I WFE-8, WFE-30, WF-8, WF-30, WFK-

8, WFDS-8, WFDS-30

J WFE-12, WF-12, WFK-12

100

110

0102030405060708090100 110120 130140 150160 170180

TOTA L DYNAMIC HEAD IN FT OF WATER

GALONES POR MINUTO

CARGA TOTAL EN PIES DE AQUA

Curvas de rendimiento de la bomba

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

PIEZAS DE REEMPLAZO

24 25

Número

artículo

P/N Descripción

1 357199 Abrazadera, Cam & Ramp, Almendra

1 357150 Abrazadera, Cam & Ramp, Negro

2 357151 Tapa, transparente, bomba WFE

2 357156 Tapa, resistente química, Cam & Ramp

3 350013 Tapa WFE Anillo en O

4 070387 Canastilla del ﬁltro, WFE

5 070430 Perno, 3/8 - 16 x 1,25, cabeza hexagonal

acero inox, 4 Req.

6 072184 Arandelas, 3/8 x 13/16 O.D. acero inox,

6 Req.

7 070431 Perno, 3/8 - 16 x 1,75, cabeza hexagonal

acero inox, 2 Req.

8 071403 Tuerca, 3/8, 16 hex hd., 2 req.

9 357100 Placa de sello de Empaque, Negro

10 357149 Voluta & placa de sello, Almendra

Kit de reemplazo

10 350015 Voluta & Olla de Bomba WFE,

Almendra

10 357157 Voluta & Olla de Bomba WFE, Negro

11 355227 Anillo en O Parker de Bomba WFE,

#2-238

12 071660 Tornillo de Tope, #4-40 X 1-1/8 SFE,

2 req.

13 072928 Montaje de Difusor, WFE- 12, Sólo 3 HP

13 072927 Montaje de Difusor, WFE- 2-8,

.5 HP–2.5 HP

14 071652 Tornillo de Tope, 1/4, 20 x 1 lh. Phillips

Número

artículo

P/N Descripción

15 075713 Arandela de Hule de Bomba WFE

16 071734S Sello PA-7 con Asiento Ceramico, PS1000

16 071728 Sello A7 con Asiento Ceramico, PS201

17 070429 Perno, 3/8, 16 x 7/8 s/s hex hd., 4 req.

18 350201 Placa de Sello Juego WFE, Almendra

(Incluye sello mecánico instalado)

# 9, 16 & 18

18 350101

Placa de Sello Juego WFE, Negro

(Incluye sello mecánico instalado)

# 16 & 18

19 070927 Pie WFE - Bomba 4, Almendra

19 357159 Pie, Negro

20 070929 Inserción de Pie de Bomba WFE, Almendra

20 357160 Inserción de Pie de Bomba WFE, Negro

21 071657 Tornillo, 1/4, 20 x 1 pulg. hex hd. s/s, 2 req.

22 071406 Tuerca, 1/4, 20 hex. hd. s/s, 2 req.

23 072183 Tuerca, 1/4, 20 hex. hd. s/s, 2 req.

24 071131 Tapón con Perilla para Desagüe, Almendra

2 req.

24 357161 Tapón con Perilla para Desagüe, Negro

2 req.

25 192115 Tapón de Desagüe de O-anillo, 2 req.

26 357149 Juego para Reemplazar Voluta/Placa de

Sello, Almendra (Incluye #1-4, 9, 10, 16, 18,

24, and 25)

27 Página siguiente

79129900 2-Velocidad Toggle Interruptor

350202 Placa de Sello Juego: Placa de Sello (Almendra),

Empaque (Negro), con instalado Sello (Incluye

Artículos: 9, 16, & 18)

350203 Placa de Sello Juego: Placa de Sello (Negro),

Empaque (Negro), con instalado Sello (Incluye

Artículos: 9, 16, & 18)

357243 Olla la Asamblea, Almendra NPT. (Incluye

Artículos: 1-4, 10, 24 [qty. 2], 25 [qty. 2])

357244 Olla la Asamblea, Negro NPT. (Incluye Artículos:

1-4, 10, 24 [qty. 2], 25 [qty. 2])

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

ENGLISH

ESPAÑOL

075451 WFE-2 ﬂuid end, 1/2 HP

075452 WFE-3 ﬂuid end, 3/4 HP

075453 WFE-4 ﬂuid end, 1 HP

075454 WFE-6 ﬂuid end, 1-1/2 HP

075455 WFE-8 ﬂuid end, 2 HP

075456 WFE-12 ﬂuid end, 3 HP

075136 WFE-2

075137 WFE-3, WFE-24

075138 WFE-4, WFE-26

075139 WFE-6, WFE-28

075140 WFE-8, WFE-30

075141 WFE-12

075145 WFDS-3, WFDS-24

075142 WFDS-4, WFDS-26

075143 WFDS-6, WFDS-28

075144 WFDS-8, WFDS-30

075251 WF-2, WF-23

075252 WF-3, WF-24

075253 WF-4, WF-26

075254 WF-6,WF-28

075255 WF-8,WF-30

075256 WF-12

79129900 2-Velocidad Toggle Interruptor

350202 Placa de Sello Juego: Placa de Sello (Almendra),

Empaque (Negro), con instalado Sello (Incluye

Artículos: 9, 16, & 18)

350203 Placa de Sello Juego: Placa de Sello (Negro),

Empaque (Negro), con instalado Sello (Incluye

Artículos: 9, 16, & 18)

357243 Olla la Asamblea, Almendra NPT. (Incluye

Artículos: 1-4, 10, 24 [qty. 2], 25 [qty. 2])

357244 Olla la Asamblea, Negro NPT. (Incluye Artículos:

1-4, 10, 24 [qty. 2], 25 [qty. 2])

No Mostrado

Fondo Líquido - Todas las Partes

sin el Motor

CSA/CUL (sólo) para Canadá.

Energía eﬁciente, sola fase.

Eﬁciencia Estánder, sola fase.

Dos velocidad, sola fase.

Número

artículo

Núm. de

pieza

Descripción

Motores

27 355008S 3/4 HP, 60 Hz, WFE-2, 3 & 24, 1 spd., Almendra, 31 lbs.

27 355010S 1 HP, 60 Hz, WFE-4 & 26, 1 spd., Almendra,, 33 lbs.

27 355012S 1-1/2 HP, 60 Hz, WFE-6 & 28, 1 spd., Almendra,, 39 lbs.

27 355014S 2 HP, 60 Hz, WFE-8 & 30, 1 spd., Almendra,, 40 lbs.

27 355016S 3 HP, 60 Hz, WFE-12, 1 spd., Almendra, 40 lbs.

27 356630S 1 HP, WFDS-4 & 26, 2 spd., 34 lbs.

27 071320S 1-1/2 HP, WFDS-6 & 28, 2 spd., 36 lbs.

27 071321S 2 HP, WFDS-8 & 30, 2 spd., 45 lbs.

27 355018S 1/2 HP, WF-2 & 23, 1 spd., Almendra, 39 lbs.

27 355020S 3/4 HP, WF-3 & 24, 1 spd., Almendra, 26 lbs.

27 355022S 1 HP, WF-4 & 26, 1 spd., Almendra, 28 lbs.

27 355024S 1-1/2 HP, WF-6 & 28, 1 spd., 39 lbs.

27 355026S 2 HP, WF-8 & 30, 1 spd., 32 lbs.

27 355033S 3 HP, WF-12, 1 spd., Almendra, 40 lbs.

27 355203S 1 HP, WFK-4, 3 ph, 1 spd., Negro, 28 lbs.

27 355204S 1-1/2 HP, WFK-6, 3 ph, 1 spd., Negro, 30 lbs.

27 355205S 2 HP, WFK-8, 3 ph, 1 spd., Negro, 37 lbs.

27 355398S 3 HP, WFK-12, 3 ph, 1 spd., Negro, 35 lbs.

27 356626S 1 HP, WFK-4, 3 ph, 1 spd., Almendra, 28lbs.

27 356627S 1-1/2 HP, WFK-6, 3 ph, 1 spd., Almendra, 30lbs.

27 356628S 2 HP, WFK-8, 3 ph, 1 spd., Almendra, 37 lbs.

27 356629S 3 HP, WFK-12, 3 ph, 1 spd., Almendra, 35 lbs.

354805S

354807S

354809S

354811S

1 HP, WFK-4, TEFC, 3 ph, 1 spd., Almendra, 28lbs.

1-1/2 HP, WFK-6, TEFC, 3 ph., 1 spd., Almendra, 30lbs.

2 HP, WFK-8, TEFC, 3 ph., 1 spd., Almendra, 37 lbs.

3 HP, WFK-12, TEFC, 3 ph., 1 spd., Almendra, 35 lbs.

Fondo Potencia Submontaje.

Incluye Artículos: 12-18, 27-28

HP TAMAÑO NO. DE

PIEZA STD.

1/2 WFE-2, WF-2, WF-23, WFK-2 073126

3/4 WFE-3, WFE-24, WF-3, WF-24,

WFK-3, WFDS-24 073127

1WFE-4, WFE-26, WF-4, WF-26,

WFK-4, WFDS-4, WFDS-26 073128

1½ WFE-6, WFE-28, WF-6, WF-28,

WFK-6, WFDS-6, WFDS-28 073129

2WFE-8, WFE-30, WF-8, WF-30,

WFK-8, WFDS-8, WFDS-30 073130

3WFE-12, WF-12, WFK-12 073131

Tabla de impulsor

SPARUS™ 160 Energy Efficient Aquaculture Duty Pump Installation and User’s Guide

NOTES127$6

SPARUS™ 160 Energy Efficient Aquaculture Duty Pump Installation and User’s Guide

NOTES127$6

Guía de instalatión y del usuario de la bomba de alto rendimiento WHISPERFLO®

1620 HAWKINS AVE., SANFORD, NC 27330 • (919) 566-8000

10951 WEST LOS ANGELES AVE., MOORPARK, CA 93021 • (805) 553-5000

WWW.PENTAIRPOOL.COM

P/N 071109 REV. J 8/29/14

*071109*

Pentair 340039 Guía del usuario

Marca: Pentair

Modelo: 340039

Categoría: Accesorios para piscinas elevadas

Tipo: Guía del usuario

Descargar PDF

informe

En otros idiomas

English: Pentair 340039 User guide

Pentair 340039 Guía del usuario

Pentair 340039 Guía del usuario

En otros idiomas

Documentos relacionados

Otros documentos