Prime TNRC21 Manual de usuario

Marca: Prime

Modelo: TNRC21

Tipo: Manual de usuario

FCC COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:

WARNING: Changes or modifications to this unit not expressly approved by the party responsible

for compliance could void the user authority to operate the equipment.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

WARNING:

Do not dispose of batteries in fire. Batteries may explode or leak. Keep the batteries away from

children and pets. Risk of fire. Do not exceed electrical ratings. For indoor use only.

INSTRUCTIONS:

1. Plug the receiver into a grounded 3-wire indoor outlet, and then plug the lights or devices to be

controlled into the receiver.

2. Make sure there is power to the outlet the receiver is plugged into.

3. Remove the plastic battery tab from the battery compartment in the back of the remote control to

activate CR2032, 3V pre-installed battery

4. The red indicator light on the receiver is lit when the indoor unit is powered on.

HELPFUL TIPS:

• Make sure the receiver is plugged into a working AC outlet

• Make sure the receiver and connected equipment are turned on

• Make sure the remote control ON button is pushed

• Make sure the CR2032, 3V battery in the remote control is still functioning

BATTERY REPLACEMENT:

1. On the right bottom corner of the remote use your finger to slide out the battery holder

2. Remove the spent battery and insert a new CR2032 3V Button-Cell Battery with

the “+” polarity mark facing up

3. Slide the battery holder back inside

4. Dispose of the old battery in compliance with all applicable laws. For detail information, contact your

local solid waste authority.

RE-SYNCHING THE TRANSMITTER:

If the remote does not turn the devices on or off, the receiver and transmitter need to be re-synched.

Plug the receiver into a properly grounded outlet. While the receiver LED is flashing, press the "ON"

button on the remote, and then press the "OFF" button on the remote until the LED stops flashing.

IC REGULATORY STATEMENT

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and

maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

INSTRUCCIONES:

1. Enchufe el receptor en un tomacorriente para interiores de 3 alambres con puesta a tierra, y

luego conecte las luces o los dispositivos que va a controlar en el receptor.

2. Cerciórese de que el tomacorriente en que va a enchufar el receptor esté energizado.

3. Retire la lengüeta plástica del compartimiento de la batería situado detrás del control remoto a

fin de activar la batería CR2032 de 3 V que viene preinstalada.

4. La luz indicadora roja en el receptor se ilumina cuando se enciende la unidad para interiores.

CONSEJOS PRÁCTICOS:

• Asegúrese de que el receptor esté enchufado a un tomacorriente de CA funcional.

• Asegúrese de que el receptor y el equipo conectado estén encendidos.

• Asegúrese de que el botón de ENCENDIDO del control remoto esté presionado.

• Asegúrese de que la batería CR2032, 3V del control remoto esté funcionando.

REEMPLAZO DE LA BATERÍA:

1. Use el dedo para deslizar el soporte de la batería en la esquina inferior derecha del control remoto.

2. Retire la batería usada e inserte una batería de botón CR2032 de 3 voltios nueva con la marca

de polaridad “+” hacia arriba.

3. Deslice el soporte de la batería de vuelta en el control remoto.

4. Elimine la batería antigua según las leyes aplicables. Para obtener información detallada,

póngase en contacto con su autoridad de eliminación de desechos sólidos local.

RESINCRONIZACIÓN DEL TRANSMISOR:

Si el control remoto no enciende ni apaga los dispositivos, el receptor y transmisor deben volver a

sincronizarse. Enchufe la unidad en un tomacorriente correctamente puesto a tierra. Mientras el

LED del receptor está destellando, pulse el botón de encendido (ON) y luego el botón de apagado

(OFF) en el control remoto hasta que el LED deje de destellar.

DECLARACIÓN DE NORMAS DEL IC

De acuerdo con las regulaciones del Ministerio de Industria de Canadá, este transmisor de radio puede funcionar

únicamente utilizando un tipo de antena y una ganancia máxima (o inferior) aprobada para el transmisor por el

Ministerio de Industria de Canadá. Para disminuir la interferencia potencial de radio con otros usuarios, el tipo de

antena y su ganancia deben elegirse de tal forma que la potencia isótropa radiada equivalente (eirp, por sus siglas en

inglés) no sea mayor de lo necesario para una comunicación eficaz.

Este dispositivo cumple con las normas RSS sin licencia del Ministerio de Industria de Canadá. El funcionamiento está

sujeto a las siguientes dos condiciones: (1) este dispositivo no debe causar interferencia y (2) este dispositivo debe

aceptar cualquier interferencia recibida, incluso aquella que pudiese causar un funcionamiento no deseado del

dispositivo.