Husqvarna PAC IV-10Y Manual de usuario

IPL, PAC IV,2007-07, 542 20 11-32

PORT-A-CUT IV

Spare Parts

Piezas de repuesto

PAC IV–75E PAC IV–8KM PAC IV–9W PAC IV–10Y

PAC IV–11R PAC IV–13H PAC IV-13.5R PAC IV–14KC

PAC IV–14KCR

PAC IV–14KM PAC IV–16KM PAC IV–16BV

PAC IV–18BV

PAC IV–18H PAC IV–20H (Engine Mounted Fuel Tank)

PAC IV–20H (Cowl Mounted Fuel Tank)

This Document Supersedes ONLY The “Parts List” Section of

Document P/N 0A7669 “PAC IV Operating Instruction & Parts List”.

Continue Usage Of P/N 0A7669 “Operating Instructions & Parts List” As “Operating Instructions” for 8KM,

9W, 10Y, 11R, 16BV, 18BV Models.

Este documento reemplaza SOLAMENTE a la “Lista de Piezas” del documento P/N 0A7669 “Instrucciones

de Operación y Lista de Piezas del PAV IV”.

Continúa el uso de P/N 0A7669 “Instrucciones de Operación y Lista de Piezas” como “Instrucciones de

Operación” para los modelos 8KM, 9W, 10Y, 11R, 16BV, 18BV.

542 20 11-32

HUSQVARNA CONSTRUCTION PRODUCTS

2

PARTS LIST INDEX

For quick supply of spare parts and to avoid any lost time, it is essential to quote the data on the

manufacturer’s plate fixed to the machine and the part description to be replaced with every order.

Model Designation Key

Model POWER SOURCE Model POWER SOURCE

PACIV-75E 7-1/2 HP Baldor Electric (3 Phase) PACIV-14KC

14 HP Kohler Command (Electric)

PACIV-8KM *

8 HP Kohler Magnum PACIV-14KCR

14 HP Kohler Command (Recoil)

PACIV-9W *

9 HP Wisconsin

PACIV-14KM *

14 HP Kohler Magnum

PACIV-10Y **

10 HP Yanmar Diesel PACIV-16KM 16 HP Kohler Magnum

PACIV-11R *

11 HP Robin

PACIV-16BV *

16 HP Briggs & Stratton

PACIV-13H 13 HP Honda

PACIV-18BV *

18 HP Briggs & Stratton

PACIV-13.5R 13.5 HP Robin

PACIV-18H *

18 HP Honda

PACIV-20H 20 HP Honda

* Model Out Of Production – Shown For Service Parts Only

** 10Y Model Available Only Upon Special Request

DESCRIPTION PAGE

Warnings......................................................................................................................................... 4 - 5

Figures & Parts Lists & Wiring Diagrams:

1. Frame Group....................................................................................................................6 - 9

2. Engine & Blade Shaft Group............................................................................................ 10 - 15

3. Drivematic Group ............................................................................................................. 16 – 18

4. Fuel Tank Group – 20H.................................................................................................... 19

5. Accessories......................................................................................................................20 - 21

6. Wide Cutting Kits (3/4″ & 1″ Wide) (Special Option)........................................................ 22 - 24

7. Electrical Components (7-1/2 Electric Model Only) ......................................................... 25

8. Wiring Diagram: 75E........................................................................................................ 26

9. Notes:............................................................................................................................... 27

10. Notes:............................................................................................................................... 27

11. Wiring Diagram: 8KM....................................................................................................... 28

12. Wiring Diagram: 9W.........................................................................................................28

13. Wiring Diagram: 10Y........................................................................................................29

14. Wiring Diagram: 11R........................................................................................................29

15. Wiring Diagram: 13H........................................................................................................30

16. Wiring Diagram: 14KM..................................................................................................... 30

17. Wiring Diagram: 14KC ..................................................................................................... 31

18. Wiring Diagram: 14KCR................................................................................................... 32

19. Wiring Diagram: 16KM..................................................................................................... 33

20. Wiring Diagram: 16BV / 18BV..........................................................................................34

21. Wiring Diagram: 18H & 20H.............................................................................................35

22. Wiring Diagram: 20H (Red Stripe Wire Harness) ............................................................ 36

23. Wiring Diagram: 20H (Blue Stripe Wire Harness)............................................................ 37

Decal Descriptions and Locations.................................................................................................. 38 - 40

Engine Mounting Locations & Base Attaching Points .................................................................... 41

Option Availability Chart - Per Model .............................................................................................43 - 45

Repair and Spare Parts ........................................................................................................

......... 45

Additional Warnings........................................................................................................................ Back Cover

3

INDICE DE LA LISTA DE PIEZAS

Para una rápida provisión de las piezas de repuesto y para evitar cualquier pérdida de tiempo, con cada

orden de compra es esencial mencionar los datos de la placa del fabricante fijada a la máquina y la

descripción de la pieza a ser reemplazada.

Clave de Designación de Modelos

Modelo FUENTE DE ENERGIA Modelo FUENTE DE ENERGIA

PACIV-75E 7-1/2 HP, Baldor Eléctrico (3 Fases) PACIV-14KC

14 HP, Kohler Command (Electric)

PACIV-8KM *

8 HP, Kohler Magnum PACIV-14KCR

14 HP, Kohler Command (Recoil)

PACIV-9W *

9 HP, Wisconsin

PACIV-14KM *

14 HP, Kohler Magnum

PACIV-10Y **

10 HP, Yanmar Diesel PACIV-16KM 16 HP, Kohler Magnum

PACIV-11R *

11 HP, Robin

PACIV-16BV *

16 HP, Briggs & Stratton

PACIV-13H 13 HP, Honda

PACIV-18BV *

18 HP, Briggs & Stratton

PACIV-13.5R 13.5 HP Robin

PACIV-18H *

18 HP, Honda

PACIV-20H 20 HP, Honda

* Modelo fuera de producción – Se muestra para piezas de repuesto solamente

** Modelo 10Y disponible como pedido especial solamente

DESCRIPCION PAGINA

Advertencias....................................................................................................................................4 – 5

Listas de Ilustraciones y Piezas y Diagramas de Cableado:

1. Grupo de Marco................................................................................................................6 - 9

2. Grupo del Motor y Eje de la Hoja......................................................................................10 - 15

3. Transmisión Automática ...................................................................................................16 – 18

4. Grupo de tanque de combustible – 20H...........................................................................19

5. Accesorios.........................................................................................................................20 - 21

6. Equipos para Corte Ancho (3/4″ y 1″ de Ancho) (Opción Especial) ................................22 - 24

7. Componentes Eléctricos (Modelo Eléctrico 7-1/2 Solamente).........................................25

8. Diagrama de Cableado: 75E.............................................................................................26

9. Notas:................................................................................................................................27

10. Notas:................................................................................................................................27

11. Diagrama de Cableado: 8KM............................................................................................28

12. Diagrama de Cableado: 9W..............................................................................................28

13. Diagrama de Cableado: 10Y.............................................................................................29

14. Diagrama de Cableado: 11R ............................................................................................29

15. Diagrama de Cableado: 13H ............................................................................................30

16. Diagrama de Cableado: 14KM..........................................................................................30

17. Diagrama de Cableado: 14KC..........................................................................................31

18. Diagrama de Cableado: 14KCR .......................................................................................32

19. Diagrama de Cableado: 16KM..........................................................................................33

20. Diagrama de Cableado: 16BV / 18BV ..............................................................................34

21. Diagrama de Cableado: 18H / 20H...................................................................................35

22. Diagrama de Cableado: 20H ............................................................................................36

23. Diagrama de Cableado: 20H ............................................................................................37

Descripciones y Localizaciones de Calcomanías...........................................................................38 - 40

Localizaciones del Montaje del Motor y Puntos de Colocación de Bases......................................41

Tabla de Disponibilidad de Opciones - Por Modelo........................................................................43 - 45

Piezas de Repuesto y Reparación .................................................................................................45

Advertencias Adicionales.......................................................................................Cubierta Posterior

4

SAFETY FIRST!!

WARNINGS

WARNING: FAILURE TO COMPLY WITH THESE WARNINGS

AND INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS INJURY.

Each machine is supplied with an operating instruction manual. Operators

and maintenance people of this equipment must read and be familiar with

the safety warnings in the operation manual. Failure to obey the warnings

may result in serious injury or death. Follow instructions strictly to ensure

long service in normal operation. If you do not have an operator’s manual

(P/N 0A7768), call TOLL FREE 1-800-288-5040.

Always park the machine on a level surface with the engine “OFF” and the

ignition switch set in the “OFF” position before performing any

maintenance. Let the machine cool down! Disconnect battery!

The manufacturer accepts no responsibility caused by unsuitable use or

modifications.

For repairs and service parts, contact you authorized DB/T dealer.

This saw was designed for certain applications only DO NOT modify this

saw or use for any application other than for which it was designed. If you

have any questions relative to its application, DO NOT use the saw until

you have contacted Diamant Boart Inc. and we have advised you.

Husqvarna Construction Products North America

17400 West 119th Street

Olathe, Kansas 66061

Telephone: 1-800-288-5040

Read the entire operator’s manual before operating this machine.

Understand all the warnings, instructions and controls. If you do not have

an operator’s manual (P/N 0A7768) call TOLL FREE 1-800-288-5040.

5

¡SEGURIDAD ANTE TODO!

ADVERTENCIAS

ADVERTENCIA: EL NO RESPETAR ESTAS ADVERTENCIAS E INSTRUCCIONES DE

OPERACION PUEDE PROVOCAR GRAVES LESIONES O LA MUERTE

.

Cada máquina se suministra con un manual de instrucciones de operación. Los

operadores y los mecánicos de este equipo deben leer y familiarizarse con las

advertencias de seguridad dadas en este manual. El no respetar las

advertencias puede provocar graves lesiones o la muerte. Siga las

instrucciones al pie de la letra para asegurar una larga vida de servicio durante

operación normal. Si no tiene un manual del operador (N/P 0A7768), llame a su

concesionario Target más cercano. Si se necesitan ejemplares adicionales,

lammar SIN CARGO al 1-800-288-5040.

Lea todo este manual y familiarícese con el funcionamiento de la máquina

antes de ponerla en marcha. Entienda todas las advertencias, instrucciones y

controles. Si no tiene un manual del operador (N/P 0A7768), llame a su

concesionario Target más cercano. Si se necesitan ejemplares adicionales,

lammar SIN CARGO al 1-800-288-5040.

Siempre estacione la máquina en una superficie plana con el motor APAGADO

y el interruptor de encendido puesto en la posición APAGADO (OFF) antes de

hacer trabajos de mantenimiento en la máquina. ¡Deje que la máquina se

enfríe! ¡Desconecte la batería! El fabricante no se hace responsable del uso o

modificaciones indebidas!

El fabricante no se hace responsable del uso o modificaciones indebidas!

Para reparaciones y piezas de repuesto, póngase en contacto con el

concesionario DB/T autorizado.

Esta sierra fue diseñada para ciertas aplicaciones solamente. NO la modifique

ni utilice para ninguna otra aplicación salvo aquéllas para las cuales fue

diseñada. En caso de dudas respecto a su aplicación, NO use la sierra sin

antes haber consultado por escrito a Diamant Boart, Inc. y haber recibido

nuestras indicaciones.

Husqvarna Construction Products North America

17400 West 119th Street

Olathe, Kansas 66061

1-800-288-5040

6

FIGURE 1 – Frame Group / Grupo de Marco

88

89

90

7

FIGURE 1 – Parts List (Items 1 - 62) (See Notes for Items Marked With “C” or “D”)

(REV 2-12-2007)

Diag

Loc.

Part

No.

Qty

Req

Description (* Denotes Metric Item)

Diag

Loc.

Part

No.

Qty

Req

Description (* Denotes Metric Item)

1

502437901

1 Frame (Metric) – Husq Gray 36 020010 1 Key, Woodruff (ANSI #405)

*1 167835 1 Frame Weldment (Metric) – Black

2 020551 2 Setscrew, Socket Hd., 5/16"-18 x 1/4" 37 167878 1 Spacer, Zinc Plated

3 139579 1 Axle, Rear 38

542190434

1 Bearing, 1/2" Bore

4 049923 2 Collar, Lock, 5/8" Bore *39 139761 2 Capscrew, Hex Hd., M6 x 1.0 x 20mm

4A 020551 2 Setscrew, Socket Hd., 5/16"-18 x 1/4" *40 139745 2 Locknut, Fiber, M6 x 1.0

5 020747 4 Washer, Flat, 5/8" USS

41 ------ --

Use Item 41C or 41D (See Note C or D)

6 040126 2 Wheel, 6" OD, 5/8" Bore 41C 139024 1 Crank, Handle (NLA use 177951)

*7 167833 2 Support, Engine Base (Metric) 41D 177922 1 Crank, Handle

*8 139749 6 Capscrew, Hex Hd., M10 x 1.5 x 25mm 42 020788 1 Lockwasher, Split, 1/2"

*9 162004 6 Lockwasher, Split, M10 43 030210 1 Nut, Acorn, 1/2"-13 UNC

*10 167831 1 Base, Engine (Metric)

44 ------ --

Use Item 44C or 44D (See Note C or D)

*11 139741 4 Capscrew, Hex Hd., M12 x 1.75 x 30mm 44C 139022 1 Bolt, Shoulder, 1/2" DIA, 3/8"-16 UNC

12 020788 4 Lockwasher, Split, 1/2" 44D ------ -- ------------

13 020745 4 Washer, Flat, 1/2" 45 ------ --

Use Item 45C or 45D (See Note C or D)

*14 167439 1 Capscrew, Hex Hd, M12 x 1.75 x 100mm 45C 139100 1 Handle, Plastic, 3/8"-16 UNC

*15 167819 3 Bracket, Guard Mounting (Metric) 45D 032250 1 Handle, Aluminum, Revolving (Press Fit)

*16 197227 6 Capscrew, Hex Hd., M8 x 1.25 x 20mm 46 139021 1 Valve, Water

*17 020785 6 Lockwasher, Split, M8 47 020405 2 Screw, Round Hd, Phillips, #10-24 x 3/8"

18

502437801

Shaft Guard – Husq Gray 48 020782 2 Lockwasher, Split, #10

18 167837 1 Shaft Guard Weldment

*19 177067 2 Capscrew, Hex Hd., M8 x 1.25 x 85mm 49 ------ --

Use Item 49C or 49D (See Note C or D)

*20 020785 2 Lockwasher, Split, M8 49C 020810 1 Fitting, 90 Street Elbow, 1/2" NPT

49D ------ -- ------------

21 167775 1 Front Axle Weldment

22 043260 2 Collar, 1" Bore 50 ------ --

Use Item 50C or 50D (See Note C or D)

*23 167781 2 Pivot Block (Metric) 50C 167897 1 Fitting, 90 Male Elbow, 1/2" NPT

24 041175 2 Grease Fitting 50D ------ -- ------------

*25 139749 4 Capscrew, Hex Hd., M10 x 1.5 x 25mm

51 ------ --

Use Item 51C or 51D (See Note C or D)

*26 162004 4 Lockwasher, Split, M10 51C 167960 1 Fitting, 45 Street Elbow, 1/2" NPT

27 020768 4 Washer, Flat, 3/4" SAE 51D ------ -- ------------

28 020614 2 Cotter Pin, 1/8" Dia x 1" Long 52 045642 1 Hose Fitting & Filter Washer

29 040091 2 Wheel, 5" DIA

30 160164 1 Pin, Yoke 53 ------ --

Use Item 53C or 53D (See Note C or D)

53C 167892 1 Hose Assy, 1/2" ID x 40" Long

31 020766 1 Washer, Flat, 1/2" SAE 53D 176177 1 Hose Assy, 1/2" ID x 49" Long

32 177239 1 Pin, Rue Ring,1/2" DIA

54

502437601

Bar, Pointer, Straight – Husq Gray

33 ------ --

Use Item 33C or 33D (See Note C or D)

54 167906 1 Bar, Pointer, Straight - Black

33C 177026 1 Adjustment Nut w/ Fitting, 5/8-11UNC

33D 177954 1 Adjustment Nut w/ Fitting, 5/8-8 ACME

55

502437701

Bar, Pointer, Offset – Husq Gray

55 167908 1 Bar, Pointer, Offset - Black

34 ------ --

Use Item 34C or 34D (See Note C or D)

34C 040139 1 Grease Fitting 56 041231 1 Rod, Pointer, 3/8"-16 UNC

34D 163140 1 Grease Fitting (2-5/8” Long) 57 041220 1 Wheel, 3" Dia, w/Bushing

35 ------ --

Use Item 35C or 35D (See Note C or D)

58 020199 1 Locknut, Fiber, 3/8"-16 UNC

35C 167789 1 Screw, Adjustment, 5/8-11UNC *59 139749 2 Capscrew, Hex Hd., M10 x 1.5 x 25mm

35D 177915 1 Screw, Adjustment, 5/8-8 ACME *60 139748 2 Locknut Fiber, M10 x 1.5

*61 197227 1 Capscrew, Hex Hd., M8 x 1.25 x 20mm

*62 139738 1 Locknut, Fiber, M8 x 1.25

Notes:

C) These Items (Marked with a C) Effective from First Unit Production (S/N 167250) To Approx. February, 2000.

D) These Items (Marked with a D) Effective Spring (Approx. February) 2000.

8

FIGURE 1 – Frame Group / Grupo de Marco

88

89

90

9

FIGURE 1 – Parts List (Items 63 - 99) (See Notes for Items Marked With “C” or “D”)

(REV 2-12-2007)

Diag

Loc.

Part

No.

Qty

Re

q

Description (* Denotes Metric Item)

Diag

Loc.

Part

No.

Qty

Req

Description (* Denotes Metric Item)

63 177025 1 Front Pointer Assy (# 54-59 & #89-92) 88 020762 2 Washer, Flat, 1/4" SAE

64 167911 1 Handle Bar Weldment 89 172137 1 Rope, 5/32" x 80" Long (Nylon)

65 139568 2 Grip, Handle Bar 90 162761 3 Clamp, Hose

66 177557 2 Knob, Handle, 3/8"-16 UNC 91 020136 1 Nut, Std. Hex, 3/8"-16

92 020786 1 Lockwasher, Split, 3/8"

67

502437501

1 Control Panel – Husq Gray

67 ------ --

Use of Item 67C or 67D (See Note C or D)

93

041160 2

Collar, Lock, 3/4

" Bore

67C 167800 1 Control Panel Weldment, PC Blue 94 020766 1 Washer, Flat, 1/2" SAE

67D 177909 1 Control Panel Weldment, PC Black

*68 197227 9 Capscrew, Hex Hd., M8 x 1.25 x 20mm 95 ------ --

Use Item 95C or 95D (See Note C or D)

69 020763 9 Washer, Flat, 5/16" SAE 95C ------ -- ----------

*70 139738 9 Locknut, Fiber, M8 x 1.25 95D 177923 1 Latch, Crank Handle, Zinc Plated

*71 177930 1 Cowl Weldment, PC Blue (Metric)

71

502437401

1 Cowl Weldment - Husq Orane

*72 139749 4 Capscrew, Hex Hd., M10 x 1.5 x 25mm 96 ------ --

Use Item 96C or 96D (See Note C or D)

96C ------ -- ----------

*73 173014 4 Washer, Flat, M10 96D 171710 1

Washer, Wave Spring, .28 ID

*74 139748 4 Locknut, Fiber, M10 x 1.5

97 ------ --

Use Item 97C or 97D (See Note C or D)

75

502437301

1 Cover, Rear Cowl, Husq Gray

75 167807 1 Cover, Rear Cowl, PC Black (See Note “E”) 97C ------ -- ----------

97D 161531 1

Washer, Fiber, .75x.265x.093” Thick

*76 167925 4 Capscrew, Flange Hd., M8 x 1.25 x 30mm

*77 139738 4 Locknut, Fiber, M8 x 1.25 98 ------ --

Use Item 98C or 98D (See Note C or D)

98C ------ -- ----------

78

502447801

1 Shield, RH – Husq Orange 98D 139761 1 Capscrew, Hex Hd., M6 x 1.00 x 20mm

78 167814 1 Shield, RH (See Note “E”)

*79 197227 3 Capscrew, Hex Hd., M8 x 1.25 x 20mm 99 ------ --

Use Item 99C or 99D (See Note C or D)

80 020785 3 Lockwasher, Split, 5/16" 99C ------ -- ----------

81 020763 3 Washer, Flat, 5/16" SAE 99D 139745 1 Locknut, Fiber, M6 x 1.00

82

502444701

1 Belt Guard (Standard) – Husq Orange

82

502444601

1 Belt Guard (Tall) – Husq Orange

— 167825 1 Belt Guard (Standard)

— 167969 1 Belt Guard (Tall) (5E,7.5E,14KM, 18-20H)

— 177002 1 Belt Guard (10Y Only)

— 177595 1 Belt Guard (14KCR)

*83 197227 5 Capscrew, Hex Hd., M8 x 1.25 x 20mm

*84 020785 5 Lockwasher, Split, M8

85 020763 5 Washer, Flat, 5/16" SAE

86 163988 1 Wrench, 1-1/16" Open End

*87 197170 1 Wing Bolt, M6 x 1.0 x 16mm

Notes:

C) These Items (Marked with a C) Effective from First Unit Production (S/N 167250) To Approx. February, 2000).

D) These Items (Marked with a D) Effective Spring (Approx. February, 2000).

E) These Items Used Only On Drivematic Equipped Models Effective Spring (Approx. February) 2000. Eliminated from

Push Models – can be purchased separately for Push models Effective Spring 2000.

10

FIGURE 2 – Engine & Blade Shaft Groups / Grupo del Motor y Eje de la Hoja

11

FIGURE 2 - Parts List (Items 1 – 12)

(REV 2-12-2007)

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(* Denotes Metric Item)

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(* Denotes Metric Item)

1 139214 1 Engine, 8KM *5 139765 4 Capscrew, Hex., M10x1.5x40mm

— 011401 1 Engine, 9W (10Y, 13.5R, 16KM)

— 177015 1 Engine, 10Y (Diesel) *–– 167748 4 Capscrew, Hex Hd., M10x1.5x65mm (18H, 20H)

— 177118 1 Engine, 11R

(For 20H, Before S/N 422140–See Note L)

— 167821 1 Engine, 13H *––

725250001

4 Capscrew, Hex Hd., M10x1.5x45mm ( 20H)

— 196010 1 Engine, 13.5R

(Eff S/N 422140 for 20H–See Note L)

— 167861 1 Engine, 14KC (Electric Start Only) *— 139766 4 Capscrew, Hex Hd, M10x1.5x45mm (11R, 13H)

— 177607 1 Engine, 14KCR (Recoil Start Only) *— 047792 4 Capscrew, Hex Hd, M10 x 1.5 x 30 mm (8KM)

— 167996 1 Engine, 14KM *— 167749 4 Capscrew, Hex Hd, M10 x 1.5 x 90 mm (9W)

— 139250 1 Engine, 16KM — 020323 4 Capscrew, Hex Hd., 3/8-16UNC x 1”

— 139697 1 Engine, 16BV (Full Thread) (14KC, 14KCR)

— 167981 1 Engine, 18BV *–– 173058 4 Capscrew,Hex Hd.,M8x1.25x45mm (16BV, 18BV)

— 177282 1 Engine, 18H (No Longer Available)

— 177461 1 Engine, 20H (See Note J) 6 173014 4 Washer, Flat, M10

— 190334 1 Engine, 20H, Modified (See Note J)

(8KM, 9W, 10Y, 11R, 13H, 13.5R, 16KM, 20H)

— 190092 1 Engine, 20H (See Note J) — 020743 4 Washer, Flat, 3/8" (14KC)

*— 020742 4 Washer, Flat, 5/16" (16BV, 18BV)

1A 020067 1 Key, 1/4" Sq. x 1-1/4"

— 020078 1 Key, 1/4" Sq. x 3/4" (14KM, 16KM) *7 139748 4 Locknut, Fiber, M10 x 1.5

— 177608 1 Key, Bevel, 1/4" Sq. x 2-5/8” (14KCR)

(8KM, 9W, 10Y, 11R, 13H, 13.5R, 16KM, 18H, 20H)

— 020786 4 Lockwasher, Split, 3/8" (14KC, 14KCR)

1B —------ 1 Element, Air Cleaner (See Note “A”) *— 020199 2 Locknut, Fiber, 3/8"-16 (14KM)

— 177528 1 Element, Air Cleaner (18H, 20H)

*8 167133 1 Fitting, M12 x 10mm Barb (13H)

2 177014 1 Motor, Electric (51E) *— 177065 1 Fitting Assy, M14 x 3/8” Barb (11R, 13.5R)

— 000923 1 Motor, Electric (53E) — 020819 1 Fitting, 3/8" NPT x 3/8" Barb

— 167994 1 Motor, Electric (75E) (9W, 14KC, 14KCR, 16BV, 18BV)

— 177017 1 Fitting, 1/2" NPT x 3/8" Barb (8KM)

3 167746 1 Pulley, 3G3V2.65, 1GRL-1.00 w/SS — 177018 1 Fitting, 3/4" NPT x 3/8" Barb (14KM,16KM)

(8KM, 10Y, 11R, 13H, 13.5R) –– –– 1 Fitting, Oil Drain (18H, 20H )

— 139298 1 Pulley, 3G3V3.15 - 1.125 w/SS (9W) (Honda # 15558-ZJ1-010AH)

— 139288 1 Pulley, 3G3V2.65-1.125-w/SS — 177019 1 Fitting Assy, M16 x 1.5 x 3/8" Barb (10Y)

(14KM, 14KC, 14KCR)

— 167942 1 Pulley, 4G3V2.65 - 1.125 w/SS *9 167305 1 Hose Assembly, Oil Drain (All except noted)

(16KM, 20H) (See Note J) –– 020967 1 Hose, Oil Drain (12") (18H, 20H Only)

— 167889 1 Pulley, 4G3V2.65-1.00 w/SS –– 167304 1 Hose Assembly, Oil Drain (14KCR)

(16BV, 18BV, 18H, 20H) (See Note J)

— 060139 1 Pulley, 2G3V2.65 - .875 w/SS (5E) 10 020049 1 Hose Clamp

— 041134 1 Pulley, 3G3V2.80 - 1.375 w/SS (75E) *11 167307 1 Blanking Cap

*12 167623 1 Tube Nut, M16

3A 020550 2 Setscrew,Soc. Hd, 5/16-18 x 3/8" (5E, 7.5E)

— 020540 2 Setscrew,Soc. Hd,1/4-20 x 1/4" (13-20 HP)

— 020541 2 Setscrew, Soc. Hd, 1/4-20 x 3/8" (9 W)

4 161499 2 V-Belt, 3VX355 (51E, 53E)

— 163857 3 V-Belt, 3VX425 (75E)

— 163869 3 V-Belt, 3VX375 (10Y)

— 161499 3 V-Belt, 3VX355 (8KM, 11R, 13H, 13.5R, 14KC)

— 163857 3 V-Belt, 3VX425 (14KCR)

— 172281 3 V-Belt, 3VX400 (9W, 14KM)

— 163869 4 V-Belt, 3VX375 (16KM, 18H, 20H-See Note L)

(For 20H, Before S/N 422140–See Note L)

161499 2 V-Belt, 3VX355 (51E, 53E)

— 161499 4 V-Belt, 3VX355 (16BV, 18BV, 20H-See Note L)

(Eff S/N 422140 for 20H–See Note L)

See Notes on Page 15

12

FIGURE 2 – Engine & Blade Shaft Group / Grupo del Motor y Eje de la Hoja (Continued)

13

FIGURE 2- Parts List (Items 13 - 72)

(REV 2-12-2007)

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(* Denotes Metric Item)

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(* Denotes Metric Item)

13 164238 1 Clamp (Used On 1994 Models Only)

*42 167943 1 Blade Guard Assy – 14” (Complete)

–– 166673 1 Clamp, Insulated, 5/8” I.D. x 1/4" Hole (14kcr)

*— 195129 1 Blade Guard - Compl – 18” Husq Gray

*— 195140 1 Blade Guard - Compl – 20” Husq Gray

*14 139761 1 Capscrew, Hex Hd., M6 x 1.0 x 20mm

43

502447301

1 Blade Guard, Front – 18” Husq Gray

–– 163688 1 Capscrew, Hex Hd., M6 x 1.0 x 16mm (14kcr)

43

502447701

1 Blade Guard, Front – 20” Husq Gray

*15 139745 1 Locknut, Fiber, M6 x 1.0

— 139076 1 Front Blade Guard Weldment – 14”

— 139596 1 Front Blade Guard Weldment – 18” (Note H)

*16 167478 1 Capscrew, Hex Hd., M8 x 1.25 x 25mm

— 195120 1 Front Blade Guard Weldment – 18” (Note H)

— 180846 1 Front Blade Guard Weldment – 20” (Note H)

— 139749 4 Capscrew, Hex Hd., M10 x 1.5 x 25mm (14KCR)

— 195134 1 Front Blade Guard Weldment – 20” (Note H)

17 020763 2 Washer, Flat, 5/16" SAE

44 ------ -- Rear Blade Guard - Not Available Use Item 42

— 173014 4 Washer, Flat, M10 (14KCR)

45 139075 1 Hinge (Note H)

*18 139738 1 Locknut, Fiber, M8 x 1.25

45A 195127 1 Hinge (Note H)

— 139748 4 Locknut, Fiber, M10 x 1.5 (14KCR)

*46 139761 6 Capscrew, Hex Hd, M6 x 1.0 x 20mm (Note H)

*19 139749 3 Capscrew, Hex Hd., M10 x 1.5 x 25mm

*46A 167478 6 Capscrew, Hex Hd M8 x 1.25x25mm (Note H)

*20 173014 3 Washer, Flat, M10

47 020762 6 Washer, Flat, 1/4" SAE (Note H)

*21 139748 3 Locknut, Fiber, M10 x 1.5

*47A 173059 6 Washer, Flat, M8 (Note H)

*22 139749 4 Capscrew, Hex Hd, M10 x 1.5 x 25mm (5E, 75E)

*48 139745 6 Locknut, Fiber, M6 x 1.0 (Note H)

*23 173014 4 Washer, Flat, M10

*48A 139748 7 Locknut, Fiber, M8 x 1.25 (Note H)

*24 139748 4 Locknut, Fiber, M10 x 1.5

49 040275 1 Fitting, 3/8" NPT Male x 3/4" Male

25 167990 1 Motor Base (75E)

50 139045 1 Manifold

— 177599 1 Engine Base (14KCR)

51 139051 1 Gasket, Manifold

26 167992 2 Spacer, Engine (9W, 14KM, 18H, 20H)

*52 167551 4 Capscrew, Hex Hd, M6 x 1.0 x 40mm

27 020365 2 Capscrew, Hex Hd., 3/8"-16 x 2-1/4"

*53 139745 4 Locknut, Fiber, M6 x 1.0

28 020323 2 Capscrew, Hex Hd.,3/8-16 x 1"(Full Thread)

54 167045 2 Water Tube -14"

29 020377 2 Capscrew, Hex Hd., 3/8"-16 x 1-1/2"

— 167046 2 Water Tube -18" & 20"

30 167894 1 Blade Shaft-Complete-3 Groove (5 – 14 HP)

55 020864 2 Plug, 1/8" NPT

— 167893 1 Blade Shaft-Complete-4 Groove (16 – 20 HP)

56 049212 2 Clamp, Water Tube

31 167846 1 Nut, 5/8"-11UNC-LH Thread (Black Finish)

*57 167818 4 Screw, Flat Hd., M6 x 1.0 x 16mm

32 167962 1 Outer Collar w/ Drive Pin

*58 139745 4 Locknut, Fiber, M6 x 1.0

32A 167964 1 Drive Pin, 3/8" Dia x 1-1/8" Long

59 040330 1 Spring

33 167961 1 Blade Shaft w/ Inner Collars *60 167761 2 Capscrew, Hex Hd, M5 x 0.8 x 20mm

33A 167185 2 Inner Collar *61 172011 4 Nut, Standard Hex M5 x 0.8

34 020067 1 Key, 1/4" Sq. x 1-1/4" 62 020782 2 Lockwasher, Split, #10

35 167895 2 Bearing w/Collar & SS (Eccentric Lock) *63 197227 1 Capscrew, Hex Hd M8 x 1.25 x 20mm

*64 020785 1 Lockwasher, Split, M8

36 020540 2 Setscrew, Socket Hd., 1/4"-20 x 1/4"

*37 139752 4 Capscrew, Hex Hd., M10 x 1.5 x 75mm *65 167749 1 Capscrew, Hex Hd, M10 x 1.5 x 90mm

*38 173014 4 Washer, Flat, M10 *66 162004 1 Lockwasher, Split, M10

*39 139748 4 Locknut, Fiber, M10 x 1.5 *67 173014 1 Washer, Flat, M10

68 139255 1 Battery, 12V, 230 CCA – WET

40 139300 1 Pulley, 3G3V3.65-1" w/SS (5 - 14HP ) -- 139255A 1 Battery, 12V, 230 CCA - DRY (Opt.)

— 167896 1 Pulley, 4GR3V3.65-1" w/SS (16 - 20 HP)

40A 020541 2 Setscrew, Soc. Hd., 1/4"-20x3/8" (For 139300) *69 167786 1 Battery Box Weldment

— 020541 4 Setscrew, Soc. Hd., 1/4"-20x3/8" (For 167896) 70 167036 1 Strap, Battery Mount (Includes Item70A)

70A 163248 1 Strip, Sponge Rubber (15 inches)

41 167847 1

Nut, 5/8"-11UNC-RH Thread (Gray Finish)

*71 197227 2 Capscrew, Hex Hd, M8 x 1.25 x 20mm

72 020785 2 Lockwasher, Split, 5/16”

See Notes on Page 15

14

FIGURE 2 – Engine & Blade Shaft Group / Grupo del Motor y Eje de la Hoja (Continued)

15

FIGURE 2- Parts List (Items 73 - 105)

(REV 2-12-2007))

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(* Denotes Metric Item)

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(* Denotes Metric Item)

73 020763 2 Washer, Flat, 5/16” SAE 88 167959 1 Weight Kit (26 lbs.) (Optional)

*74 197227 2 Capscrew, Hex Hd., M8 x 1.25 x 20mm 89 180418 4 Weight Bar-1/2" Thick (6-1/2 lbs. Each)

75 020763 2 Washer, Flat, 5/16" SAE — — 2 Weight Bar-1" Thick (13 lbs. Each)

*76 139738 2 Locknut, Fiber, M8 x 1.25 — — — (1" Not Available Use 2 Of P/N 180418)

*77 197227 1 Capscrew, Hex Hd., M8 x 1.25 x 20mm 90 020329 2 Capscrew, Hex Hd., 3/8"-16 x 2-3/4"

91 020199 2 Locknut, Fiber, 3/8"-16

78 020785 1 Lockwasher, Split, 5/16"

79 020763 1 Washer, Flat, 5/16" SAE 92 167963 1 Outer Collar Assy-1/2"Cut (Optional)

80 177063 1 Battery Cable (+) (RED) 93 167865 1 Outer Collar, 4.50 OD x 1/2" Cut

––

542190395

1 Battery Cable (+) (RED)(14KC,18H,20H) 94 020304 1 Drive Pin, 3/8" x 1-1/2"

*81 167891 1 Battery Cable, (-) (BLACK) 95 167189 1 Tiedown Bracket Kit (Optional)

*82 163688 2 Capscrew, Hex Hd., M6 x 1.0 x 16mm 96 167125 2 Eyenut, Saw Tiedown, 3/8"-16UNC

*83 139745 2 Locknut, Fiber, M6 x 1.0 97 020323 2 Capscrew, Hex Hd., 3/8"-16 x 1"

98 020786 2 Lockwasher, Split, 3/8"

84 167735 1 Ignition Switch w/ Key (16KM)

–– 163830 1 Ignition Switch w/Key (18H, 20H ) (Notes C & F) 99 167985 1 Fitting, 45 Deg Street, 3/8" NPT (9W)

–– 177920 1 Ignition Switch w/Key (18H, 20H ) (Notes D & F) 100 139098 1 Flap, Splash

*101 167761 2 Capscrew, Hex Hd., M5 x 0.8 x 20mm

85 139272 1 Wiring Harness (16KM) *102 173047 2 Washer, Flat, M5

–– 177283 1 Wiring Harness (18H, 20H) (See Notes C & G) *103 172316 2 Locknut, Fiber, M5 x 0.8

–– 177913 1 Wiring Harness (18H, 20H) (See Note D & G)

––

542190390

1 Wiring Harness-20H (See Note K) 104 177066 2 Boot, Rubber – Battery

86 139156 1 Stop Switch Assembly (8KM)

105 177068 2 Boot, Rubber – Cable (14KC Only)

— 139196 1 Stop Switch Assembly (9W) — 177066 1 Boot, Rubber – Cable (18H, 20H)

— 177021 1 Stop Switch Assembly (11R, 13H)

— 196019 1 Stop Switch Assembly (13.5R) Items Not Shown On Figure 2:

— 177022 1 Stop Switch Assembly (14KC)

— 167104 1 Guard, Muffler (Optional: 14KM, 16KM)

— 177612 1 Stop Switch Assembly (14KCR)

— 177023 1 Stop Switch Assembly (14KM)

-- ------ 1 Regulator (18H, 20H)

(Honda P/N 31620-ZG5-003)

— 167727 1 Stop Switch Assembly (16BV, 18BV)

-- 166890 2 Capscrew, Hex Hd, M6 x 1.0 x 30mm **

-- 020762 2 Washer, Flat, ¼” SAE**

87 041317 1 Switch, Push-Button -- 139745 2 Locknut, Fiber, M6 x 1.0 **

** Use To Attach Regulator (18H, 20H)

Figure 2 Notes:

A) See Engine Distributor For Item 1B (Element) For The Following Models: 8KM, 9W, 10Y, 11R, 13H, 13.5R, 14KM, 14KCR,

14KC, 16KM, 16BV, 18BV.

C) These Items (Marked with a C) Effective from First Unit Production (S/N 167250) To Approx. February, 2000).

D) These Items (Marked with a D) Effective Spring (Approx. February, 2000).

F) Ignition Switch P/N 163830 must be used with P/N 177283 Wiring Harness. Ignition Switch P/N 177920 must be used with

P/N 177913 Wiring Harness. When both items are serviced together it is suggested that the 177920 / 177913 part

combination be used because the push-on wire connectors are easier to assemble.

G) Wiring Harness P/N 177913 can be identified by the RED stripe near the “engine end” of the harness. P/N 177283 does

not have a colored stripe.

H) For Item 45A, P/N 195127 Hinge (1/4” Thick) use P/N 195120 Front Guard Weldment, 18” or P/N 195134 Front Guard Weldment, 20” and M8

attaching hardware (Items 46A, 47A & 48A). For Item 45, P/N 139075 Hinge (1/8” Thick) use P/N 139228 Front Guard Weldment, 18” or P/N 174672

Front Guard Weldment, 20” and M6 attaching hardware (Items 46, 47 & 48).

J) Engine model changed for saws mfg. After 15November2002. P/N 177461 Engine has a 1.00” dia. Crankshaft and

requires P/N 167889 pulley (1.00” I.D.). Effective about 15November2002 with saw serial number 383022; units mfg. using

P/N 190334 Engine and requires P/N 167942 pulley (1.125” I.D.). P/N’s 177461 & 190334 Engines (w/ Engine Mounted

Fuel Tanks) Not Available as of April 2003. P/N 190092 Engine & Fuel Tank Group (See Figure 4) is the only replacement

for a complete older style engine.

K) Wiring Harness P/N 542190390 can be identified by a BLUE stripe at one end, & is used only with Engine P/N 190092.

L) PAC IV-20H Eff. S/N 422140 (Built about 10/11/2004): Eliminated P/N 167992 Spacer. Belt Changed to 161499 (3VX355).

16

FIGURE 3 - Drivematic Group / Transmisión Automática

1

2

3

4

5

6

7

8

9

10

1

2

1

3

14

15

1

6

17

18

19

2

0

2

3

24

24A

25

26

27

A

1

6A

28

2

9

6

0

3

0

31

32

33

34

35

59

A

59

3

6

37

38

3

9

4

0

4

1

4

2

55

43

44

45

46

4

7

48

4

9

A

49

5

0

51

5

2

56

5

7

5

8

39A

2

1

21

20A

2

8

A

53

54

17

FIGURE 3 – Parts List

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(* Denotes Metric Item)

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(* Denotes Metric Item)

1 167876 1 Platform Weldment, Transmission *29 139740 2 Capscrew, Hex Hd., M6 x 1.0 x 25mm

2 167882 2 Linkage *30 139745 2 Locknut, Fiber, M6 x 1.0

*3 139749 2 Capscrew, Hex Hd., M10 x 1.5 x 25mm 31 020766 2 Washer, Flat, 1/2" SAE

*4 173014 4 Washer, Flat, M10 32 044181 2 Wheel, Drive

*5 139748 1 Locknut, Fiber, M10 x 1.5 33 020643 2 Roll Pin, 1/4 x 1-1/4"

*6 047792 1 Capscrew, Hex Hd., M10 x 1.5 x 30mm 34 044161 2 Bearing, Flange, 3/4" Bore

*7 139748 1 Locknut, Fiber, M10 x 1.5 35 164296 1 Fitting, Grease, 45 Deg, 1/4"-28 Thread

*8 167791 1 Lever, Transmission Engage (Metric) 36 041175 1 Fitting, Grease, 90 Deg, 1/4"-28 Thread

*9 167034 1 Capscrew, Hex Hd., M10 x 1.5 x 40mm 37 167784 1 Shaft, Transmission Drive

Full Thread 38 020062 1 Key, 3/16" Square x 1-1/4" Long

*10 173014 2 Washer, Flat, M10 39 041389 1 Sprocket-w/SS, #35,48Teeth,3/4" Bore

*11 139748 1 Locknut, Fiber, M10 x 1.5 39A 020541 2 Setscrew, Soc Hd, 1/4-20 x 3/8"

12 167843 1 Pin, Clevis, 1/2" x 1-1/2" (Included w/ Item 39)

13 020766 3 Washer, Flat, 1/2" 40 139104 1 Chain, #35, 63 Pitches

14 167035 1 Pin, Cotter, Hair Spring (1/2" Pin) 41 048740 4 Capscrew, Hex Hd., 3/8"-16 x 1-1/4"

15 041427 1 Knob, Trans. Lever, 3/8-16UNC 42 020199 4 Locknut, Fiber, 3/8"-16

16 046131 1 Transmission (includes Item 16A) 43 167874 1 Arm, Idler

16A 048326 1 Oil Reservoir w/Cap and O-Ring

*17 139752 4 Capscrew, Hex Hd., M10 x 1.5 x 75mm *44 177064 1 Capscrew, Hex Hd., M10 x 1.5 x 45mm

*18 173014 4 Washer, Flat, M10 Full Thread

*19 139748 4 Locknut, Fiber, M10 x 1.5 *45 173014 7 Washer, Flat, M10

20 041360 1 Pulley 1GA6.00 - .67 w/SS *46 162004 1 Lockwasher, Split, M10

20A 020541 2 Setscrew, Soc Hd., 1/4-20UCN x 3/8" *47 139750 1 Nut, Std. Hex, M10 x 1.5

21 020085 3 Key, Woodruff (ANSI #404) *48 164968 1 Capscrew, Hex Hd., M10 x 1.5 x 50mm

Full Thread

22 167932 1 V-Belt, 4L410 (16KM) 49 167764 1 Pulley, 1G4L3.0-.375 w/ Bushing

— 160938 1 V-Belt,4L420 (Includes Item 49A)

(75E, 8KM, 9W, 14KC, 16BV, 18BV)

49A 167762 1 Bushing, M10 & 3/8" Bore

— 043750 1 V-Belt, 4L440 (10Y, 11R, 13H, 18H, 20H) *50 162004 1 Lockwasher, Split, M10

— 048649 1 V-Belt, A-44 (14KCR) *51 139750 1 Nut, Std. Hex, M10 x 1.5

— 164369 1 V-Belt, A-41 (14KM) *52 139748 1 Locknut, Fiber, M10 x 1.5

53 139102 1 Spring

23 167937 1 Lever Weldment, Control 54 020618 1 Pin, Cotter 3/16 Dia x 1" Long

24 046179 1 Pin, Pivot w/Setscrew (Incl. Item 24A) 55 139102 2 Spring

24A 020547 1 Setscrew, Socket Hd., #10-24 x 1/4" 56 177000 2 Pin, Clevis, 1/2 Dia x 1" Long

25 020199 1 Locknut, Fiber, 3/8"-16UNC 57 020766 8 Washer, Flat 1/2"

*26 173014 1 Washer, Flat, M10 58 177239 2 Pin, Rue Ring, 1/2" Dia

27 041370 1 Sprocket, w/Setscrew, #35, 12 Teeth 59 041301 1 Pulley 1GA2.75 - 1.125 w/SS

27A 020540 2 Setscrew, Socket Hd., 1/4"-20 x 1/4" (Includes # 59A) (9W, 14KM, 14KC)

(Included w/ Item 27) 59A 020551 2 Setscrew, Soc Hd, 5/16"-18 x 1/4"

(9W, 14KM, 14KC)

28 167873 1 Cable Assembly, Trans. Speed Control 60 020762 2 Washer, Flat, 1/4"

(Includes Item 28A)

28A ——— 2 Nut, Jam, 7/16"-20UNF

18

FIGURE 4 – Fuel Tank Group (Cowl Mounted): 20 HP Honda (After April2003)

Grupo de tanque de combustible

FIGURE 4 – Parts List (See Notes Below)

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

1 539300742 1 Fuel Tank, w/ Bushing (Note 2) 12 162004 4 Lockwasher, Split, M10

2 539106188 1 Cap, Fuel 13 173014 4 Washer, Flat, M10

3 542190393 1 Bushing, Hex, 1/8NPT x 1/4NPT (Male) 14 542190401 1 Light, Low Oil Indicator

4 542190392 1 Valve, Fuel, 1/8”NPT x ¼” SAE -- -- -- Optional Items:

5 191328 1 Fuel Line, ¼”SAE x 15” Long 15 190249 1 Kit: Tach-Hourmeter (Note 3)

6 174740 1 Clamp, Worm Gear, SAE 006 16 539300556 1 Tach-Hourmeter (Surface Mount)

7 542190396 1 Fuel Tank Bracket 17 197293 2 Screw, M4 x 16

8 539102845 4 Spring, Fuel Tank 18 197290 2 Washer, M4

9 021416 4 Capscrew, Hex Hd, .312-18UNC x 1” 19 167485 2 Locknut, Fiber, M4 x .70

10 020742 8 Washer, Flat, .312 20 542190402 1 Decal, Low Oil Indicator Light

11 139744 4 Capscrew, Hex Hd, M10 x 1.5 x 20mm 21 542190403 1 Tape, Heat Reflecting

Notes:

1. Items shown in this Figure are Only For Use With P/N 192092 Engine, 20H. Older models of the 20hp Honda Engine That Use

The Engine Mounted Fuel Tank Are No Longer Available, As of April 2003.

2. Fuel Tank (P/N 539300742) Includes a Female ¼” NPT Bulkhead Bushing (Not Shown On This Parts List).

3. Tach-Hourmeter Kit (P/N 190249) Includes Installation Instructions, & Items 15-19, & Additional Parts Used For Other Models.

This Tach-Hourmeter Kit Can Also Be Installed On PACIV-13H (13 hp Honda Model), & Most Other Gasoline Powered PAC IV

Models.

19

Notes:

__________________________________________

20

FIGURE 5 – Accessories / Accesorios

21

FIGURE 5 – Parts List

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION (

* Metric Items)

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

(*Metric Item)

0 167965 1 Water Pump Kit

1 177016 1 Water Pump

40 167966 1 Water Tank Kit

2 ——— 1 Fuse – 10 Amp, Automotive ATC Type 41 139706 1 Tank, Water (5 Gallon)

3 ——— 4 Spacer, Rubber (Included w/ Item 0) 42 177050 1 Spigot, Water Tank (VENT)

*4 166890 4 Capscrew, Hex Hd., M6 x 1.0 x 30mm 43 177060 1 Hose – 3/8" x 30"

5 020762 4 Washer, Flat, 1/4" 44 020049 1 Hose Clamp

*6 139745 4 Locknut, Fiber, M6 x 1.0 45 174020 1 Fitting, 3/4" FGH x 3/8" ID Hose

7 539300242 1 Fitting, 1/2" NPT Street Elbow 46 177047 1 Bracket, Water Tank

8 139616 1 Hose Assembly, Water-3/4" FGH x 1/2 MPT *47 167478 2 Capscrew,Hex Hd, M8 x 1.25 x 25mm

9 090308 1 Fitting, 3/4" NPT 45 Male Elbow (Full Thread)

10 045643 1 Hose Fitting & Washer *48 173059 4 Washer, Flat, M8

11 163594 1 Water Pump Bracket *49 139738 2 Locknut, Fiber, M8 x 1.25

*12 197227 2 Capscrew, Hex Hd., M8 x 1.25 x 20mm 50 167724 1 Tiedown, Elastic 28"

13 020742 2 Washer, Flat, 5/16"

*14 139738 2 Locknut, Fiber, M8 x 1.25

55 --------- 1 Hour Meter Group – 16BV & 18BV

15 040273 1 Fitting, 3/4" NPT 90 Street Elbow (Includes items 56-60)

16 163769 1 Hose Assy, Water-3/4" (Outlet) 56 177030 Control Panel – Modified (Blue)

17 052120 1 Toggle Switch, Water Pump On/Off 57 163779 Hour Meter w/Mounting Kit

18 167869 1 Wire Harness, Water Pump 58 177057 Wire Assy – Ground (-) (16KM,16BV,18BV)

19 167935 1 Decal, Water Pump On/Off -- 177285 1 Wire Assy – Ground (-) (18H & 20H)

20 178687 1 Fitting, 3/4 MGH x 3/4 MPT 59 177058 1 Wire Assy – Positive (+) (16B, 18BV)

-- 177286 1 Wire Assy – Positive (+) (18H & 20H)

30 177059 1 Kit, Lift Bail (All Models – Except 20H)

31 167857 1 Lift Bail 60 177056 1 Terminal, 1/4" Female

*32 139744 4 Capscrew, Hex Hd., M10 x 1.5 x 20mm

65 --------- 1 Hour Meter Group – 16 KM

–– 139749 2 Capscrew, Hex Hd., M10 x 1.5 x 25mm

(Includes items 56-58, 66)

(139749 at Lower Holes–18H & 20H Only)

-- --------- 1 Hour Meter Group – 18H & 20H

*33 162004 4 Lockwasher, Split, M10

(Includes Items 56-59)

*34 173014 4 Washer, Flat, M10 66 177051 1 Wiring Harness – Modified (16KM)

*35 167532 1 Capscrew, Hex Hd., M12 x 1.75 x 140mm

*36 173042 2 Washer, Flat, M12

37 177031 1 Spacer, Lift Bail

*38 139742 1 Locknut, Fiber, M12 x 1.75

39 020745 4 Washer, Flat, 1/2" USS

(Install between Item 31 & Cowl In

Lower Holes Only– 18H & 20H Only)

t

See “Option Availability” Section of this Document

For the Availability of Options & Accessories on each Model

WARNING: Refer To The Operating Instructions And Applicable Instruction Sheets For The

Proper Installation of Options & Accessories Before Beginning The Installation! Part Numbers For

The Applicable Instruction Sheets Are Shown In The “Option Availability” Section Of This

Document.

Ver la Sección “Disponibilidad de Opciones” de Este Documento

Para Verificar la Disponibilidad de Opciones y Accesorios para cada Modelo

ADVERTENCIA: ¡Antes de comenzar la instalación, refiérase a las Instrucciones de

Operación y a las Hojas de Instrucciones aplicables para realizar apropiadamente la

instalación de opciones y accesorios! Los Números de Piezas para las Hojas de

Instrucciones aplicables se muestran en la sección “Disponibilidad de Opciones” de este

documento.

22

Figure 6 – Wide Cutting Kits (Optional Or Accessory)

Equipos para Corte Ancho (3/4″ y 1″ de Ancho) (Opción Especial)

P/N 177535 Kit, Complete, 3/4″ Wide P/N 177542 Kit, Complete, 1″ Wide

23

Figure 6 – Parts List

Item Qty

Part No

Description (* Denotes Metric Item) Item Qty

Part No

Description (* Denotes Metric Item)

--

1 177535 Kit, Complete, 3/4

" Wide Cut (Note 1)

24 1 040275 Adapter, 3/8 NPT-3/4

" Garden Hose

--

1 177542 Kit, Complete, 1

" Wide Cut (Note 2)

25 4 167551 Capscrew, Hex Hd., M6 x 1.0 x 40

26 4 139745 Locknut, Fiber M6 x 1.0

-- -- ------ Note 1: 3/4" Kit Includes All Items 27 1 163275 Guard, Splash

-- -- ------ except Item 45 & 7A (P/N 163485) 28 2 139761 Capscrew, Hex Hd., M6 x 1.0 x 20

-- -- ------ Note 2: 1" Kit Includes Items 1-55 29 2 139746 Washer, Flat M6

30 2 139745 Locknut, Fiber M6 x 1.0

1 1 177531 Shaft, Blade (3/4" & 1" Cutting) 31 2 161003 Water Tube w/ Plug

2 2 167895 Bearing, 1", Eccentric Lock 32 2 049212 Clamp, Water Tube

3 4 139752 Capscrew, Hex Hd., M10 x 1.50 x 75 mm 33 4 167818 Screw, Flat M6 x 1.0 x 16

4 4 173014 Washer, Flat M10 34 4 139745 Locknut, Fiber M6 x 1.0

5 4 139748 Locknut, Fiber M10 x 1.50 35 1 049154 Hinge

6 1 177529 Collar, Inner 36 6 167478 Capscrew, Hex Hd., M8 x 1.25 x 25

7 1 167963 Collar, Outer w/ 1.50" Dowel Pin 37 6 173059 Washer, Flat M8

7A 1 020304 Pin, Dowel .375 x 1.50 (.75" Cut) 38 6 139738 Locknut, Fiber M8 x 1.25

-- 1 163485 Pin, Dowel .375 x 1.75 (1.0" Cut) ** 39 1 043145 Spring

8 1 167896 Pulley, 4G3V3.65 w/ Setscrews 40 2 139761 Capscrew, Hex Hd., M6 x 1.0 x 25

9 1 020067 Key, 1/4" Sq. x 1-1/4" 41 4 172017 Nut, Hex M6 x 1.0

10 1 167847 Nut, Flange, 5/8-11UNC, RH thread 42 1 177544 Front Guard Weldment Only

11 1 167846 Nut, Flange, 5/8-11UNC, LH thread 43 1 177537 Spacer, Guard

12 1 177536 Blade Shaft Assembly (Items 1-11) 44 2 020864 Plug, 1/8" Socket Head

13 1 177533 Guard, Shaft (3/4" & 1" Cutting) 45 1 177541 Spacer, Arbor (1" Cutting Only)**

14 2 167553 Capscrew, Hex Hd., M8 x 1.25 x 100 46 1

15700939

Fitting, Street Tee, 3/8" NPT

15 2 020785 Lockwasher, Split M8 47 1 020815 Fitting, Street Elbow, 3/8" NPT

16 1 177538 Blade Guard Assembly (Items below) 48 1 177547 Fitting, 3/8" NPT x 1/4" Barb

17 1 176668 Capscrew, Hex Hd., M10 x 1.5 x 120 49 1 177548 Hose, 1/4" ID x 15" Long

18 1 162004 Lockwasher, Split M10 50 1 161133 Fitting, Female, 1/8" NPT x 1/4" Barb

19 1 173014 Washer, Flat M10 51 1 020811

Fitting, 90° Str. Elbow 1/8

" NPT

20 1 197227 Capscrew, Hex Hd., M8 x 1.25 x 20 52 1 048902

Nozzle, 30°

21 1 020785 Lockwasher, Split M8 53 1 020764 Washer, Flat 3/8” SAE

22 1 049196 Manifold 54 1 166672 Clamp, 5/16 x 9/32" Hole

23 1 049206 Gasket, Manifold 55 2 020049 Clamp, Gear 7/32-5/8”

24

WARNING:

Refer to Instruction Sheet 0A7767 for proper installation of the Wide Cutting Kits. Install

the proper blade spacers (See Below) between each diamond blade so that the segments on the

diamond blades DO NOT touch when the outer flange is tightened. Failure to follow this warning could

result in injury or death to the operator or persons in the work area! Special Note for 1" wide cutting:

Replace the 1-1/2

" long dowel pin (Item 7A, P/N 020304) that is installed from the factory in the outer

flange with the 1-3/4

" long dowel pin (Item 7A, P/N 163485) included in the 1" wide cutting kit. If dowel

pin does not go through ALL the blades and into inside flange then the maximum blade stacking

capacity has been exceeded, and some blade(s) MUST be removed.

Blade Spacers (Not Included in this Kit)

Part No. Qty Description

049500 As Required Spacer, 5.0" Outside Dia x 1.00" Arbor x 16 Gauge (.060") Thick

049502 As Required Spacer, 5.0" Outside Dia x 1.00" Arbor x 18 Gauge (.048") Thick

161800 As Required Spacer, 8.0" Outside Dia x 1.00" Arbor x 4 Gauge (.224") Thick

161801 As Required Spacer, 8.0" Outside Dia x 1.00" Arbor x 6 Gauge (.194") Thick

161802 As Required Spacer, 8.0" Outside Dia x 1.00" Arbor x 8 Gauge (.164") Thick

161803 As Required Spacer, 8.0" Outside Dia x 1.00" Arbor x 10 Gauge (.134") Thick

161804 As Required Spacer, 8.0" Outside Dia x 1.00" Arbor x 14 Gauge (.075") Thick

161805 As Required Spacer, 8.0" Outside Dia x 1.00" Arbor x 15 Gauge (.067") Thick

161806 As Required Spacer, 8.0" Outside Dia x 1.00" Arbor x 18 Gauge (.048") Thick

161807 As Required Spacer, 8.0" Outside Dia x 1.00" Arbor x 20 Gauge (.036") Thick

ADVERTENCIA:

Refiérase a la Hoja de Instrucciones 0A7767 para efectuar la instalación apropiada de

los Equipos para Corte Ancho. Instale los espaciadores apropiados (ver abajo) entre cada hoja

diamantada, de manera que los segmentos de las hojas diamantadas NO se tocan cuando la brida

externa es apretada. ¡El incumplimiento de esta advertencia podría producir lesiones o la muerte del

operador o de las personas que se encuentran en el área de trabajo! Nota Especial para cortes de 1"

de ancho: Reemplace la clavija de 1-1/2” de largo (Artículo 7A, P/N 020304), que es instalada en

fábrica en la brida externa, con la clavija de 1-3/4” de largo (Artículo 7A, P/N 163485) que se incluye en

el equipo para corte de 1” de ancho. Si la clavija no pasa a través de todas las hojas y dentro de la

brida, quiere decir que se ha excedido la máxima capacidad de amontonamiento de hojas y que

alguna(s) hoja(s) DEBE(N) ser sacada(s).

Espaciadores de Hojas (no se incluyen en este equipo)

Pieza

No.

Cantidad Descripción

049500 La que sea

necesaria

Espaciador, 5.0" de Diámetro Externo x 1.00" de Eje x Calibre 16 (.060”) de

Espesor

049502 La que sea

necesaria

Espaciador, 5.0" de Diámetro Externo x 1.00" de Eje x Calibre 18 (.048”) de

Espesor

161800 La que sea

necesaria

Espaciador, 8.0" de Diámetro Externo x 1.00" de Eje x Calibre 4 (.224”) de

Espesor

161801 La que sea

necesaria

Espaciador, 8.0" de Diámetro Externo x 1.00" de Eje x Calibre 6 (.194”) de

Espesor

161802 La que sea

necesaria

Espaciador, 8.0" de Diámetro Externo x 1.00" de Eje x Calibre 8 (.164”) de

Espesor

161803 La que sea

necesaria

Espaciador, 8.0" de Diámetro Externo x 1.00" de Eje x Calibre 10 (.134”) de

Espesor

161804 La que sea

necesaria

Espaciador, 8.0" de Diámetro Externo x 1.00" de Eje x Calibre 14 (.075”) de

Espesor

161805 La que sea

necesaria

Espaciador, 8.0" de Diámetro Externo x 1.00" de Eje x Calibre 15 (.067”) de

Espesor

161806 La que sea

necesaria

Espaciador, 8.0" de Diámetro Externo x 1.00" de Eje x Calibre 18 (.048”) de

Espesor

161807 La que sea

necesaria

Espaciador, 8.0" de Diámetro Externo x 1.00" de Eje x Calibre 20 (.036”) de

Espesor

25

FIGURE 7 - Electrical Components for 75E Model Only (7-1/2 HP Electric)

Figure 7A - Items included in Conversion Kits -

A) P/N 177442 [convert 230V to 460V]

B) P/N 177443 [convert 460V to 230V]

Ilustración 7A – Artículos incluidos en los Equipos Converions

A) P/N 177442 (convierte 230V a 460V)

B) P/N 177443 (convierte 460V a 230V)

Item Qty Part No Description

1 1 190104 Starter Box Assembly, 460V (A)

-- 1 190103 Starter Box Assembly, 230V (B)

2 1 176932 Ring, Sealing, 1/2”

3 1 175244 Locknut, Conduit 1/2”

4 1 176937

Connector, Seal Tight 45°

5 1 176955 Conduit, 1/2” Flexible

6 1 176935 Connector, Seal Tight, Straight

7 1 182015 Reducer, 3/4 - 1/2”

8 3 176953 Locknut, Conduit 3/4”

9 3 182016 Wire, Black, 12 Ga. 53” Long

10 1 182017 Wire, Green, 12 Ga. 57” Long

11 1 182021 Terminal, Ring #10, 12-10 Ga.

12 1 182018 Cord, SOW, 12 Ga/4 Wire-27” Lg

13 1 182024 Strain Relief, Water Tight 3/4”

14 6 090556 Connector, Wire (A)

-- 4 090556 Connector, Wire (B)

15 1 182010 Connector, Male 480V (A)

-- 1 182012 Connector, Male 250V (B)

16 1 182009 Connector, Female 480V (A)

-- 1 182011 Connector, Female 250V (B)

17 4 177460 Capscrew, Hex M4 x 0.7 x 30

18 4 167485 Locknut, Fiber M4 x 0.7

19 4 197290 Washer, Flat M4

20 1 176933 Ring, Sealing 3/4”

FIGURE 7A

Figure 7B - Factory built saws include all Items in

Figure 6A and Figure 6B (below). Note that Item 24

holds an electrical cord that is connected to Item 16.

This cord MUST be supplied by the customer

Ilustración 7B - Las sierras hechas en fábrica

incluyen todos los artículos en la Ilustración 6A y en

la Ilustración 6B (abajo). Note que el Artículo 24

sostiene un cable eléctrico que está conectado al

Artículo 16. Este cable DEBE ser proporcionado

por el cliente.

Item Qty Part No Description

20 1 166676 Clamp, 5/8 x 3/8”

21 1 139749 Capscrew, Hex M10 x 1.5 x 25

22 1 173014 Washer, Flat M10

23 1 177457 Bracket, Strain Relief

24 1 177459 Cable Support, Bus Drop

25 1 166955 Clamp, 1 x 3/8”

FIGURE 7B

26

FIGURE 8 - Wiring Diagram & Voltage Conversion-75E (7-1/2 HP, 3 Phase Electric)

This Figure applies to all 230V and 460V 7.5 HP electric Models. Conversion kits are available to convert to and from

230V and 460V 3 phase units.

Kit P/N 177442 Convert 230V to 460V

Kit P/N 177443 Convert 460V to 230V

NOTICE: The end user is responsible for providing electrical service in accordance with the National Electric Code and

any other applicable local codes. Service must at the minimum, motor disconnection means, motor branch-circuit

short-circuit protection, motor branch-circuit ground-fault protection, and correctly sized motor circuit conductors.

Connect the green and black wires to the electric motor as shown below for your specific unit. If the electric motor

rotates backwards after wiring the unit, switch any two black line wires to reverse the motor direction.

ILUSTRACION 8 - Diagrama de Cableado y Conversión de Voltaje-75E

(Eléctrico de 7-1/2 HP, 3 Fases)

Esta ilustración se aplica a todos los modelos eléctricos de 230V y 460V de 7.5 HP. Existen disponibles equipos de

conversión para convertir unidades de 3 fases a /y de 230V y 460V.

Equipo P/N 177442 Convierte 230V a 460V

Equipo P/N 177443 Convierte 460V a 230V

NOTIFICACION: El usuario final es responsable de suministrar la energía eléctrica de acuerdo con el Código

Nacional de Electricidad y cualquier otro código local aplicable. Como mínimo, el servicio de energía eléctrica debe

tener medios para desconectar el motor, protección contra cortocircuitos del circuito ramal del motor, protección

contra fallas de la conexión a tierra del circuito ramal del motor y conductores del circuito del motor correctamente

dimensionados.

Conecte los cables verde y negro al motor eléctrico, tal como se muestra abajo para su unidad específica. Si el motor

eléctrico rota al revés después de cablear la unidad, cambie dos líneas negras cualesquiera para revertir la dirección

del motor.

WIRING DIAGRAM - 75E MODELS (7-1/2 HP, 3 Phase Electric)

27

Notes:

__________________________________________

28

FIGURE 11 – Wiring Diagram - 8KM (8 HP Kohler Magnum)

FIGURE 12 – Wiring Diagram - 9W (9 HP Wisconsin)

29

FIGURE 13 – Wiring Diagram-10Y (10 HP Yanmar Diesel)

FIGURE 14 – Wiring Diagram-11R (11 HP Robin)

30

FIGURE 15 – Wiring Diagram-13H (13 HP Honda)

FIGURE 16 – Wiring Diagram-14KM (14 HP Kohler Magnum – Recoil Start)

31

FIGURE 17 – Wiring Diagram-14KC (14 HP Kohler Command – Electric Start)

32

FIGURE 18 – Wiring Diagram-14KCR (14 HP Kohler Command – Recoil Start)

33

FIGURE 19 – Wiring Diagram-16KM (16 HP Kohler Magnum – Electric Start)

34

FIGURE 20 – Wiring Diagram-16BV & 18BV (16 & 18 HP Briggs & Stratton-Vanguard)

35

FIGURE 21 – Wiring Diagram-18H & 20H (Engine Mounted Fuel Tank & Wire Harness wo/ Strip)

R

E

D

G

R

E

N

G

R

E

N

Y

E

L

O

W

START

SOLENOID

ON

ENGINE

BLACK

TRANSISTORIZED

IGNITION UNIT

FUEL CUT

SOLENOID

BLACK

ENGINE

STOP DIODE

TRANSISTORIZED

IGNITION UNIT

ENGINE OIL

PRESSURE

SWITCH

WHITE w/ BLUE STRIP

WHITE/BLUE STRIP

BLACK

WHITE

GREY

SPARK

PLUG

SPARK

PLUG

CUT AND

TAPE OVER

HONDA

WIRE HARNESS

20 AMP CHARGE COILS

20 AMP REGULATOR / RECTIFIER

MOUNTED AT INSIDE OF RIGHT

HAND SHIELD

STARTER MOTOR

G

R

E

N

P

U

R

P

L

E

Y

E

L

O

W

RED

DS

O

B

C

KEY

SWITCH

B

L

ACK

B

L

A

C

K

BATTERY

WIRE HARNESS

B

L

A

C

K

w

/

R

E

D

S

T

R

I

P

E

B

L

A

C

K

w

/

Y

E

L

O

W

S

T

R

I

P

E

23

P

U

R

P

L

E

WHITE

1 177283 1 Honda Wiring Harness

2 163779 1 Gauge, Hour Meter

3 163830 1 Keyswitch (Wisconsin # YC78D)

4 166830 1 Switch, Toggle - Water Pump

5 177016 1 Water Pump

6 ------- 1 Fuse, 10A

7 177063 1 Battery Cable, (+) Positive, Red

8 139255 1 Battery 12V Lead-Acid

9 167891 1 Battery Cable, (-) Negative, Black

10 164370 1 Connector, Male Push-On

11 177285 1 Wire Ass'y, Hour Meter, Ground

12 177286 1 Wire Ass'y, Hour Meter, Positive

13 ------- 1 Motor, Starter

14 ------- 1 Switch, Engine Oil Pressure

(Honda #37240-ZG3-E01)

15 ------- 1 Fuel Solenoid Shut Down

16 ------- 1 Transistorized Ignition Unit

17 ------- 1 Engine Stop Diode

18 ------- 1 Spark Plug

19 ------- 1 Charging Coil, 20A

(Honda #31620-ZJ1-801)

20 ------- 1 Engine Wire Harness

21 ------- 1 Rectifier-Regulator, 20A

(Honda #31620-ZG5-003)

22 167869 1 Wiring Harness, Water Pump

23 177288 1 Terminal 5/16 Ring 16 Ga

DIAGPART QTY

LOC NO. REQ DESCRIPTION

W

i

r

i

ng D

i

agram 18 & 20 HP Hon

d

a

36

FIGURE 22 – Wiring Diagram-20H (Engine Mounted Fuel Tank & Red Stripe Wire Harness)

Ref: B-542190398 Wire Diagram

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

1 177913 1 Wiring Harness w/ Red Strip 10 --- 2 Coil, Ignition, Honda

2 --- 1 Wiring Harness, Honda Engine 11 --- 2 Spark Plug, Honda

3 163179 1 Cable, Battery, Negative (-) 12 177920 1 Switch, Ignition

4 177063 1 Cable, Battery, Positive (+) 13 139255 1 Battery, 12 Volt

5 --- 1 Starter, Honda Engine 14 177016 1 Waterpump (Optional)

6 --- 1 Stop Diode, Honda 15 166830 1 Switch, Toggle (Waterpump Option)

7 --- 1 Switch, Engine Oil Pressure, Honda 16 167869 1 Wire Harness, Waterpump

8 --- 1 Fuel Cut Solenoid, Honda 17 177288 1 Terminal, Ring, 5/16” – 16 Ga

9 --- 1 Regulator, Honda 18 --- --- ---

37

FIGURE 23 – Wiring Diagram-20H (Cowl Mounted Fuel Tank, 190092 Engine, & Blue Stripe Wire Harness)

Ref: B-542190399, Rev 2 Wire Diagram

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

DIAG

LOC.

PART

NO.

QTY

REQ

DESCRIPTION

1 542190390 1 Wiring Harness w/ Blue Strip 10 --- 2 Coil, Ignition, Honda

2 --- 1 Wiring Harness, Honda Engine 11 --- 2 Spark Plug, Honda

3 163179 1 Cable, Battery, Negative (-) 12 177920 1 Switch, Ignition

4 542190395 1 Cable, Battery, Positive (+) 13 139255 1 Battery, 12 Volt

5 --- 1 Starter, Honda Engine 14 177016 1 Waterpump (Optional)

6 --- 1 Stop Diode, Honda 15 166830 1 Switch, Toggle (Waterpump Option)

7 --- 1 Switch, Engine Oil Pressure, Honda 16 167869 1 Wire Harness, Waterpump

8 --- 1 Fuel Cut Solenoid, Honda 17 177288 1 Terminal, Ring, 5/16” – 16 Ga

9 --- 1 Regulator, Honda 18 542190401 1 Light, Low Oil Indicator

38

DECAL DESCRIPTIONS AND LOCATIONS

DESCRIPCIÓN DE CALCAMONIAS Y UBICACIONES

P/N: 502441201

Husqvarna / PAC IV

Location: Sides of Cowl

Quantity: 2

Models: All

P/N: 167936

Start / Run / Stop

Location: Control Panel

Quantity: 1

Models: 16KM, 18H, 20H (Drivematic Only)

P/N: 542190733

Location: Rear Guard at Rear of Cowl

Quantity: 1

Models: All

P/N: 169065, Muffler Hot

Location: Engine Fuel Tank

Quantity: 1

Models: Gasoline Powered Models

P/N 177891, Operating Instructions

Location: Top Of Control Panel

Quantity: 1, Models: All

39

DECAL DESCRIPTIONS AND LOCATIONS

DESCRIPCIÓN DE CALCAMONIAS Y UBICACIONES

P/N: 187681

Target / PAC IV

Location: Sides of Cowl

Quantity: 2

Models: All

P/N: 167936

Start / Run / Stop

Location: Control Panel

Quantity: 1

Models: 16KM, 18H, 20H (Drivematic Only)

P/N: 189732, Target (Blue) for Blue Surfaces

(Shown)

Or

P/N: 187693, Target (White) for Black Surfaces

Location: Rear Guard At Rear Of Cowl

Quantity: 1

Models: All

P/N: 169065, Muffler Hot

Location: Engine Fuel Tank

Quantity: 1

Models: Gasoline Powered Models

P/N 177891, Operating Instructions

Location: Top Of Control Panel

Quantity: 1, Models: All

40

DECAL DESCRIPTIONS AND LOCATIONS

DESCRIPCIÓN DE CALCAMONIAS Y UBICACIONES

P/N 040570, Grease Bearings Daily (Multi-Language)

Location: Front Of Frame or Front Of Weight Kit

Quantity: 1, Models: All

P/N 542190402,

Decal, Low Oil Indicator Light

Location: Near Lamp On Fuel

Tank Bracket, Quantity: 1

Models: 20H Models Only

P/N 167952, Transmission

Engage

Location: Rear Of Control Panel

Quantity: 1

Models: Drivematic Models

Only

P/N 167951, Water Valve ON /

OFF

Location: Rear Of Control

Panel

Quantity: 1

Models: All

P/N 160004, Transmission

Location: Transmission Fill Cap

Quantity: 1

Models: Drivematic Models Only

P/N 167935, Decal, Water Pump

Location: Rear Of Control Panel

Quantity: 1 for Water Pump

Equipped Models

P/N 176223 Decal, Warning-

Guards In Place

Location: Frame Base, Rear

Control Panel, Quantity: 2, All

Models

P/N 167755 Decal, Water Tank

Caution

Location: Water Tank Bracket

Quantity: 1 for Water Tank Option

Only

41

COMPLETE DECAL KITS - TARGET

P/N 177561 Decal Kit

PAC IV, Drivematic Model

Includes the following items**:

P/N 177562 Decal Kit

PAC IV, Push Model

Includes the following items**:

Part No. Qty Description Part No. Qty Description

167953 2 Decal, Target / PAC IV 167953 2 Decal, Target / PAC IV w/ Stripe

052130 1 Decal, Target 052130 1 Decal, Target

167951 1 Decal, Water Valve ON / OFF 167951 1 Decal, Water Valve ON / OFF

176223 2 Decal, Caution / Guards In Place 176223 2 Decal, Caution / Guards In Place

169065 1 Decal, Muffler Hot 169065 1 Decal, Muffler Hot

040570 1 Decal, Grease Bearings Daily 040570 1 Decal, Grease Bearings Daily

167949 1 Decal, Operating Instr. (Drivematic) 167950 1 Decal, Operating Instr. (Push Model)

167936 1 Decal, Start / Run / Stop

167952 1 Decal, Transmission Engage

160004 1 Decal, Transmission Oil Fill

**Kits Includes P/N’s Shown & Quantity To Complete One Unit. Specify Kit For A Drivematic or Push Model Saw.

Kits DO NOT Include Decals For Optional Water Pump, or Optional Water Tank – Order Separately.

Kits DO NOT Include Decals For Engine or Electric Motor. See The Engine / Motor Manufacturer For These Decals.

EQUIPOS COMPLETOS DE CALCOMANIAS

Equipo de Calcomanía P/N 177561

PAC IV, Modelo de Transmisión

Automática

Incluye los siguientes artículos**:

Equipo de Calcomanía P/N 177562

PAC IV, Modelo de Empuje

Incluye los siguientes artículos**:

Pieza

No.

Cant

idad

Descripción Pieza

No.

Cant

idad

Descripción

167953 2 Calcomanía, Target / PAC IV 167953 2 Calcomanía, Target / PAC IV con

Raya

052130 1 Calcomanía, Target 052130 1 Calcomanía, Target

167951 1 Calcomanía, Válvula de Agua

ENCENDIDO / APAGADO

167951 1 Calcomanía, Válvula de Agua

ENCENDIDO / APAGADO

176223 2 Calcomanía, Precaución / Protectores

en su Sitio

176223 2 Calcomanía, Precaución / Protectores

en su Sitio

169065 1 Calcomanía, Silenciador Caliente 169065 1 Calcomanía, Silenciador Caliente

040570 1 Calcomanía, Engrase los Cojinetes

Diariamente

040570 1 Calcomanía, Engrase los Cojinetes

Diariamente

167949 1 Calcomanía, Instrucciones de

Operación (Transmisión Automática)

167950 1 Calcomanía, Instrucciones de

Operación (Modelo de Empuje)

167936 1 Calcomanía, Arranque /

Funcionamiento / Parada

167952 1 Calcomanía, Engranaje de la

Transmisión

160004 1 Calcomanía, Llenado del Aceite de

Transmisión

**Los equipos incluyen las P/N mostradas y la cantidad para completar una unidad. Especificar el equipo para una

sierra de transmisión automática o modelo de empuje.

Los equipos NO incluyen calcomanías para la bomba de agua opcional o para el tanque de agua opcional. Haga su

pedido por separado.

Los equipos NO incluyen calcomanías para la máquina o el motor eléctrico. Refiérase al fabricante del motor /

máquina para obtener estas calcomanías..

42

ENGINE LOCATIONS ON ENGINE BASE

LOCALIZACIONES DE MOTOR Y DE LA BASE

ENGINE MOUNTING LOCATIONS & BASE ATTACHING POINTS

(P/N 167831 ENGINE BASE SHOWN)

LOCALIZACIONES DE MONTAJE DEL MOTOR Y PUNTOS DE UNION DE LA BASE

(P/N 167831, BASE DEL MOTOR MOSTRADA)

SYMBOL ENGINE MODEL

75E 7.5 HP ELECTRIC MODEL & 14KCR BASE ENGINE

8KM 8 HP KOHLER MAGNUM

9W 9 HP WISCONSIN

10Y 10 HP YANMAR DIESEL

11R 11 HP ROBIN

13H 13 HP HONDA

14KC 14 HP KOHLER COMMAND (ELECTRIC START)

14KCR 14 HP KOHLER COMMAND (RECOIL START)

14KM 14 HP KOHLER MAGNUM

16KM 16 HP KOHLER MAGNUM

16BV 16 HP BRIGGS & STRATTON-VANGUARD

18BV 18 HP BRIGGS & STRATTON-VANGUARD

18H 18 HP HONDA

20H 20 HP HONDA

43

Notes:

__________________________________________

44

OPTION AVAILABILITY FOR EACH MODEL

MODEL

OPTIONS

75E 8KM 9W 10Y 11R 13H 14KM 14KC

14KCR

16KM 16BV 18BV 18H 20H

Drivematic Transmission

Y Y Y Y Y Y Y Y Y Y Y Y Y Y

Weight Kit (26 Lbs.) (Note 1)

Y Y Y Y Y Y Y Y Y Y Y Y Y Y

Lift Bail Kit (Note 2)

Y Y Y Y Y Y Y Y Y Y Y Y Y N/A

Tie Down Bracket Kit

Y Y Y Y Y Y Y Y Y Y Y Y Y Y

Water Tank Kit (5 Gal.) (Note 3)

N/A Y Y Y Y Y Y Y Y Y Y Y Y N/A

Outer Flange – 1/2″Cut (Note 4)

N/R N/R

N/R

N/R N/R Y Y Y Y Y Y Y Y Y

Kit, 3/4″ Cut (Note 5)

N/R N/R

N/R

N/R N/R N/R N/R N/R N/R Y Y Y Y Y

Kit, 1″ Cut (Note 5)

N/R N/R

N/R

N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R Y

Electric Water Pump (Note 6)

N/A N/A

N/A

Y N/A N/A N/A Y N/A Y Y Y Y Y

Hourmeter Kit (Note 6)

N/A N/A

N/A

Y N/A N/A N/A Y N/A Y Y Y Y Y

Blade Guard Left / Right Cutting

14″ Blade Guard (Note 7)

L/R L/R

L/R

L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R

18″ Blade Guard (Note 8)

L/R L L L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R

20″ Blade Guard

L L L L/R L/R L/R L L/R L/R L/R L/R L/R L/R L/R

Y = Available N/A = Not Available (Item will NOT work on this model) N/R = Available but Not Recommended

L = This Size Blade Guard Will Fit Only On Left Hand Side Of Saw L/R = This Size Blade Guard Will Fit On Left or Right Side Of Saw

Notes: Warning: See operating instructions and applicable instruction sheets before installation of any of these items!

1. Weight Kit: Standard Equipment for 11R, 13H, 14KC, 16BV, 18BV, 18H, 20H With 18″ Blade Guard (See Note 7 & 8). Installation: See parts list.

2. Lift Bail Kit: Available As Factory Installed (most models). Standard equipment for 75E model because electrical control box is mounted onto lift bail (effective

January 1997). This option must be ordered to use the optional “Water Tank Kit” (See Note 3). See Instruction Sheet 0A7673 for installation instructions.

3. Water Tank Kit: Must order Lift Bail Kit to use water tank kit. Use only with dry cutting blades. Water flow (Approx. 1/2 Gallon Per Minute) is not sufficient for

use with wet cutting diamond blades. N/A for 75E models because electric control box is mounted onto lift bail. Installation: See parts list.

4. Outer Flange 1/2

″

Cutting: Mounts directly to standard bladeshaft. Use Only For Blade Stacking Width Of 7/16″– 1/2″. Use Standard Outer Flange

(P/N 167962) For Blade Stacking Width Of 0 – 3/8″. Available For Use On Right Or Left Side Of Saw.

5. Wide Cutting Kits: Available for all Models. Not recommended for engine sizes less than 16 HP (4 Belt Bladeshaft Drive). Kit Includes A 4 Groove Blade

Shaft Pulley. N/R Engines Require A 3 Groove Bladeshaft Pulley-Order & Install Separately. See Instruction Sheet 0A7767.

6. Electric Water Pump Kit / Hourmeter Kit: Available only on models shown. Engine must have electric starter to power this item. Installation: See parts list.

7. 14

″

Blade Guard: Not Available For Factory Installation--effective January 1997. Available Through Service Parts Only.

8. 18

″

Blade Guard: Standard Equipment--effective January 1997 For All Models except for 20H (20H Model Equipped with a 20″ Blade Guard).

45

DISPONIBILIDAD DE OPCIONES PARA CADA MODELO

MODELO

OPCIONES

75E 8KM 9W 10Y 11R 13H 14KM 14KC 14KCR 16KM 16BV 18BV 18H 20H

Transmisión Automática

D D D D D D D D D D D D D D

Equipo de Pesas (26 Libras) (Nota 1)

D D D D D D D D D D D D D D

Equipo de Elevación (Nota 2)

D D D D D D D D D D D D D N/D

Equipo de Ménsula de Atar

D D D D D D D D D D D D D D

Equipo de Tanque de Agua

(5 Galones) (Nota 3)

N/D D D D D D D D D D D D D N/D

Brida Externa - Corte de 1/2″(Nota 4)

N/R N/R

N/R

N/R N/R D D D D D D D D D

Equipo, Corte de 3/4″ (Nota 5)

N/R N/R

N/R

N/R N/R N/R N/R N/R N/R D D D D D

Equipo, Corte de1″ (Nota 5)

N/R N/R

N/R

N/R N/R N/R N/R N/R N/R N/R N/R N/R N/R D

Bomba de Agua Eléctrica (Nota 6)

N/D N/D

N/D

D N/D N/D N/D D N/D D D D D D

Equipo Medidor de Horas (Nota 6)

N/D N/D

N/D

D N/D N/D N/D D N/D D D D D D

Protector de Hoja Izquierdo /

Corte a la Derecha

Protector de Hoja de 14″ (Nota 7)

I/D I/D

I/D

I/D I/D I/D I/D I/D I/D I/D I/D I/D I/D I/D

Protector de Hoja de 18″ (Nota 8)

I/D I I I/D I/D I/D I/D I/D I/D I/D I/D I/D I/D I/D

Protector de Hoja de 20″

I I I I/D I/D I/D I I/D I/D I/D I/D I/D I/D I/D

D = Disponible N/D = No Disponible (El artículo NO funcionará en este modelo) N/R = Disponible pero No Recomendado

I = Este tamaño de protector de hoja se ajustará solamente a la izquierda de la sierra I/D = Este tamaño de protector de hoja se ajustará al costado

izquierdo o derecho de la sierra

Notas: Advertencia: ¡Ver las instrucciones de operación y las hojas de instrucciones aplicables antes de instalar

cualquiera de estos artículos!

1. Equipo de Pesas: Equipo convencional para los modelos 11R, 13H, 14KC, 16BV, 18BV, 18H, 20H con Protector de Hoja de 18″ (Ver Nota 7 y 8).

Instalación: Ver la lista de piezas.

2. Equipo de Elevación: Disponible como instalación en fábrica (en la mayoría de los modelos). Equipo convencional para el modelo 75E porque la caja de

control eléctrico está montada en el mecanismo de elevación (efectivo en enero de 1997). Se debe hacer el pedido de esta opción para usar el “Equipo del

Tanque de Agua” opcional (Ver Nota 3). Ver Hoja de Instrucción 0A7673 para obtener las instrucciones de instalación.

3. Equipo del Tanque de Agua: Se debe hacer el pedido del Equipo de Elevación para usar el equipo del tanque de agua. Usar solamente con hojas para

corte en seco. El Flujo de Agua (Aproximadamente 1/2 Galón Por Minuto) no es suficiente para usar con hojas diamantadas húmedas. N/D para los modelos

75E porque la caja de control eléctrico está montada en el mecanismo de elevación. Instalación: Ver lista de piezas.

46

4. Corte de 1/2

″

de la Brida Externa: Se monta directamente al eje de la hoja convencional. Usar solamente para el amontonamiento de hojas de ancho de

7/16″ – 1/2″. Usar Brida Externa Convencional (P/N 167962) para el amontonamiento de hojas de ancho 0 – 3/8″. Disponible para uso en el costado derecho

o izquierdo de la sierra.

5. Equipos para Corte Ancho: Disponibles para todos los modelos. No recomendados para tamaños de motor inferiores a 16 HP (Transmisión del Eje de la

Hoja de 4 Bandas). El equipo incluye una Polea del Eje de la Hoja de Muesca A 4. Los motores N/R requieren Poleas del Eje de la Hoja de Muesca A 3 -

Haga el pedido por separado e instale en forma separada. Ver la Hoja de Instrucción 0A7767.

6. Equipo de Bomba de Agua Eléctrica / Equipo Medidor de Horas: Disponible solamente en los modelos mostrados. El motor debe tener un arrancador

eléctrico para suministrar energía a este artículo. Instalación: Ver lista de piezas.

7. Protector de Hoja de 14": No disponible para instalación en fábrica--efectivo en enero de 1997. Disponible a través de Piezas de Servicio solamente.

8. Protector de Hoja de 18": Equipo Convencional--efectivo en enero de 1997 para todos los modelos excepto para el 20H (el modelo 20H está

equipado con un Protector de Hoja de 20″).

REPAIRS

We carry out all repairs in the shortest possible time and at the most

economical prices. (See front page for our address and phone numbers)

SPARE PARTS

For quick supply of spare parts and to avoid any lost time, it is essential to

quote the data on the manufacturer’s plate fixed to the machine and the part

number (s) to be replaced with every order.

REPARACIONES

Hacemos todas las reparaciones en los plazos más breves posibles, y a los

precios más económicos. (Vea la portada para nuestra dirección y número

de teléfono).

PIEZAS DE RECAMBIO

Para un suministro rápido de piezas de recambio y evitar cualquier pérdida

de tiempo, en cada pedido es esencial mencionar los datos de la placa de

fabricación fijada a la máquina; y el número de pieza que se va a

reemplazar.

The instructions for use and spare parts found in this document

are for information only and are not binding. As part of our

product quality improvement policy, we reserve the right to make

any and all technical modifications without prior notice.

Las instrucciones de uso y las piezas de recambio presentadas

en este documento son solamente para información y no constituyen

obligación ninguna. Como parte de nuestra política de mejoramiento

de la calidad de nuestros productos, nos reservamos el derecho de hacer

cualquiera y todas las modificaciones técnicas sin previo aviso.

The manufacturer accepts no

responsibility caused by unsuitable

use or modifications

¡El fabricante no acepta ninguna

responsabilidad por accidentes debidos

al uso indebido o modificaciones

hechas a la máquina!

47

Notes:

__________________________________________

Customer Service: 800-288-5040

Customer Serv. Fax: 800-825-0028

Printed in the USA

DUST WARNING

Cutting, especially when DRY cutting, generates dust that comes from the material being cut,

which frequently contains silica. Silica is a basic component of sand, quartz, brick clay, granite and

numerous other minerals and rocks. Exposure to excessive amount of such dust can cause:

Respiratory diseases (affecting your ability to breath), including chronic bronchitis, silicosis

and pulmonary fibrosis from exposure to silica. These diseases may be fatal;

Skin irritation and rash; and

Cancer according to NTP* and IARC*

National

* Toxicology Program / International Agency for Research on Cancer

Take precautionary steps

Avoid inhalation of and skin contact with dust, mist and fumes;

Wet cut when feasible, to minimize dust;

Wear and ensure that all bystanders wear appropriate respiratory protection such as dust

masks designed to filter out microscopic particles. (See OSHA 29 CFR Part 1910.1200)

California Prop 65 Warning:

Use of this product can cause exposure to materials known to the State of California to cause cancer

and/or birth defects or other reproductive harm.

Husqvarna Construction Products N. A.

Corporate Office

17400 West 119th Street

Olathe, Kansas 66061

Tel. 913-928-1000

Fax 913-438-7951

Husqvarna PAC IV-10Y Manual de usuario

Husqvarna PAC IV-10Y Manual de usuario

Documentos relacionados

Otros documentos