Yamaha CL1 Manual de usuario

Tipo
Manual de usuario

Este manual también es adecuado para

EN
How to Use This Reference Manual
The CL5/CL3/CL1 V5 Reference Manual (this document) allows
you to search for terms and take advantage of links in the text.
Searching for terms
To search for a term, use the search function of the software
youre using to view this document.
If you’re using Adobe Reader, enter the term in the search box
and press the <Enter> key of your computer keyboard to search
for occurrences of that term.
Displaying the next/previous view
If youre using Adobe Reader, you can jump to the previous/next
view in your viewing history. This is a convenient way to jump
back to the previous page after you’ve used a link to jump to a
different page.
Using the Function Tree
A function tree for the CL series is provided on page 4 and
following. You can use this function tree to find the page that
explains an on-screen display or function.
V5 Reference Manual
Contents
V5 Reference Manual
2
Contents
How to Use This Reference Manual .......................................................................... 1
Function Tree ............................................................................ 4
SELECTED CHANNEL section ...................................................... 6
Operations in the SELECTED CHANNEL Section ....................................................... 6
Centralogic section ................................................................. 13
Operations in the Centralogic section .................................................................... 13
Input and output patching..................................................... 18
CL console internal patching and Dante audio network patching .......................... 18
Changing the input patching ................................................................................ 19
Changing the output patching .............................................................................. 21
Inserting an external device into a channel ............................................................ 23
Directly outputting an INPUT channel ................................................................... 26
Input channels ........................................................................ 29
Signal flow for input channels................................................................................ 29
Specifying the channel name/icon ......................................................................... 30
HA (head amp) settings ......................................................................................... 32
Sending the signal from an input channel to the STEREO/MONO bus ................... 38
Added pan function (Monaural input channels only) ............................................. 41
Sending a signal from an input channel to a MIX/MATRIX bus .............................. 43
Channel name display indication ........................................................................... 47
Correcting delay between channels (Input Delay).................................................. 48
Surround output for input channels....................................................................... 51
Channel library operations..................................................................................... 55
OUTPUT channels.................................................................... 56
Signal flow for output channels ............................................................................. 56
Specifying the channel name/icon ......................................................................... 57
Sending signals from MIX channels to the STEREO/MONO bus ............................. 58
Sending signals from MIX channels and STEREO/MONO channels to
MATRIX buses............................................................................................. 60
Correcting delay between channels (Output Delay)............................................... 63
Channel library operations..................................................................................... 64
EQ and Dynamics .................................................................... 65
Using EQ ............................................................................................................... 65
Simultaneously setting EQ type.............................................................................. 68
Using dynamics ...................................................................................................... 69
Using the EQ/Dynamics libraries............................................................................. 73
Channel Job ............................................................................. 74
DCA group............................................................................................................. 74
DCA Roll-out function ............................................................................................ 77
Mute group............................................................................................................ 79
Using the Recall Safe function................................................................................. 82
Channel Link function ............................................................................................ 85
Copying, moving, or initializing a channel.............................................................. 90
About Mix Minus.................................................................................................... 94
Scene memory ......................................................................... 95
Storing and recalling scenes ................................................................................... 95
Editing scene memories........................................................................................ 100
Using the Global Paste function............................................................................ 102
Using the Focus Recall function ............................................................................ 105
Using the Fade function........................................................................................ 106
Outputting a control signal to an external device in tandem with scene recall
(GPI OUT) ................................................................................................. 109
Playing back an audio file that links to a scene recall............................................. 110
Using Preview mode............................................................................................. 112
Monitor and Cue functions ................................................... 113
Using the Monitor function .................................................................................. 114
Using the Cue function......................................................................................... 120
Talkback and Oscillator......................................................... 129
Using Talkback ..................................................................................................... 129
Using the Oscillator function ................................................................................ 131
Meters.................................................................................... 134
Operations in the METER screen ........................................................................... 134
Using an MBCL meter bridge (optional) on the CL3 or CL1 console ..................... 139
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK..... 140
About the virtual rack ........................................................................................... 140
Virtual rack operations.......................................................................................... 141
Graphic EQ operations ......................................................................................... 144
About AUTOMIXER............................................................................................... 151
Editing the internal effects .................................................................................... 154
Effects and tempo synchronization ....................................................................... 160
Using the Premium Rack....................................................................................... 161
Using the graphic EQ, parametric EQ, effect, and Premium Rack libraries ............. 172
Contents
V5 Reference Manual
3
I/O devices and external head amps .................................... 173
Using an I/O device ............................................................................................. 173
Remotely controlling an R series unit ................................................................... 175
Third-party equipment’s HA control function....................................................... 180
Remotely controlling an amp............................................................................... 182
Remotely controlling WIRELESS unit..................................................................... 183
Using an external head amp ................................................................................ 187
MIDI....................................................................................... 192
MIDI functionality on the CL series console.......................................................... 192
Basic MIDI settings .............................................................................................. 192
Using program changes to recall scenes and library items.................................... 195
Using control changes to control parameters....................................................... 197
Using parameter changes to control parameters .................................................. 199
Recorder................................................................................ 200
About the USB memory recorder ......................................................................... 200
Assigning channels to the input/output of the recorder ....................................... 200
Recording audio to a USB flash drive.................................................................... 202
Playing back audio files from a USB flash drive ..................................................... 204
Editing the title list............................................................................................... 205
Recording or playing back using a computer DAW .............................................. 206
Using the CL console with Nuendo Live............................................................... 209
Setup ..................................................................................... 213
About the SETUP screen....................................................................................... 213
User settings ........................................................................................................ 215
Preferences .......................................................................................................... 222
USER DEFINED keys ............................................................................................. 224
Functions that can be assigned to USER DEFINED keys ........................................ 226
USER DEFINED knobs........................................................................................... 231
Functions that can be assigned to USER DEFINED knobs ...................................... 232
Assignable encoders ............................................................................................ 234
Functions that can be assigned to the assignable encoders .................................. 235
GAIN/PAN/ASSIGN knob (assignable encoder) functions ..................................... 236
Custom fader bank .............................................................................................. 236
Master fader ........................................................................................................ 237
Custom fader bank functions ............................................................................... 238
Console Lock ....................................................................................................... 238
Saving and loading setup data to and from a USB flash drive............................... 239
Formatting a USB flash drive................................................................................ 245
Word clock and slot settings ................................................................................ 246
Using cascade connections .................................................................................. 248
Basic settings for MIX buses and MATRIX buses ................................................... 252
Switching the entire phantom power supply on/off.............................................. 253
Specifying the brightness of the touch screen, LEDs, channel name displays,
and lamps ................................................................................................. 253
Setting the date and time of the internal clock ..................................................... 254
Setting the network address ................................................................................. 254
Dante audio network settings ............................................................................... 256
Dante Device Lock................................................................................................ 258
Support for Dante Domain Manager .................................................................... 259
Using GPI (General Purpose Interface) .................................................................. 271
Help function......................................................................... 276
Loading a Help/text file from a USB flash drive ..................................................... 276
Viewing Help........................................................................................................ 276
Using USER DEFINED keys to recall Help directly................................................... 277
Other functions ..................................................................... 278
Initializing the unit to factory default settings ....................................................... 278
Adjusting the detection point of the touch screen (Calibration function) .............. 278
Adjusting the faders (Calibration function) ........................................................... 279
Fine-tuning the input and output gain (Calibration function) ............................... 279
Adjusting the channel color (Calibration function)................................................ 281
Adjusting the brightness of the channel name display .......................................... 281
Adjusting the contrast of the channel name display.............................................. 282
Initializing the console settings and Dante audio network settings........................ 282
Update procedure for NAME SUB CPU firmware................................................... 283
Update function to Dante firmware ...................................................................... 283
Warning/Error Messages ...................................................... 284
Index...................................................................................... 287
Function Tree
V5 Reference Manual
4
Function Tree
Page numbers in parentheses ( ) are the page numbers of the
Owners Manual(booklet).
Main
SELECTED CHANNEL 6
OVERVIEW 14
FUNCTION ACCESS AREA (18)
CHANNEL PARAMETER
PATCH/NAME 20, 31, 57
GAIN/PATCH 33
1ch 33
8ch 34
CH1-48 36
CH49-72/ST IN 36
OUTPUT
Indication only
INPUT DELAY 48
8ch 48
CH1-48 49
CH49-72/ST IN 49
DELAY SCALE 48
INSERT/DIRECT OUT 24
1ch 24, 27
8ch 25, 27
HPF/EQ 65
1ch 65
8ch 67
CH1-48 68
CH49-72/ST IN 68
OUTPUT 68
DYNAMICS 70
1ch 70
KEY IN SOURCE SELECT 71
8ch 71
CH1-48 72
CH49-72/ST IN 72
OUTPUT 72
CHANNEL PARAMETER
MIX SEND/MATRIX SEND 45
TO STEREO/MONO 58
8ch 58
CH1-48 59
CH49-72/ST IN 59
OUTPUT 59
SURROUND 51
LIBRARY
CHANNEL LIBRARY 55
EQ LIBRARY 73
DYNAMICS LIBRARY 73
GEQ/PEQ LIBRARY 172
EFFECT LIBRARY 172
Portico5033/Portico5043/Portico5045/U76/
Opt-2A/EQ-1A/DynamicEQ/Buss Comp 369/
MBC4 LIBRARY
172
DANTE INPUT PATCH LIBRARY 174
RACK
VIRTUAL RACK 141
RACK MOUNTER 144
GEQ EDIT 145
RACK LINK 145
EFFECT RACK 156
EFFECT EDIT 156
EFFECT TYPE 156
PREMIUM RACK 161
PREMIUM RACK MOUNTER 162
PREMIUM RACK EDIT 162
AUTOMIXER 151
PARAMETRIC EQ 148
I/O DEVICE
DANTE PATCH 173
DANTE INPUT PATCH 174
OUTPUT PATCH 175
I/O 176
AMP 182
WIRELESS 183
EXTERNAL HA 189
EXTERNAL HA RACK 189
EXTERNAL HA EDIT 189
EXTERNAL HA PORT SELECT 190
MONITOR
MONITOR 114
CUE 124
MONITOR 116
OSCILLATOR 132
TALKBACK 130
METER
INPUT METER 134
OUTPUT METER 134
RTA METER 136
SETUP
USER SETUP 213
PREFERENCE 222
USER DEFINED KEYS SETUP 224
USER DEFINED KEY SETUP (List) 224
USER DEFINED KNOBS SETUP 231
USER DEFINED KNOB SETUP (List) 231
ASSIGNABLE ENCODER SETUP 234
CUSTOM FADER BANK/MASTER FADER 237
FADER ASSIGN SELECT 236
USER LEVEL/CREATE USER KEY 216
CREATE KEY 217
SAVE KEY 220
LOGIN 218
SAVE/LOAD 239
I/O DEVICE
Function Tree
V5 Reference Manual
5
NOTE
The explanations in this reference manual will use the CL5.
In the case of the CL3/CL1, some screens will not show
channels and faders that do not exist on those models.
WORD CLOCK/SLOT SETUP 246
CASCADE IN/OUT PATCH 249, 251
OUTPUT PORT 63
MIDI/GPI 192, 271
MIDI SETUP 193
PROGRAM CHANGE 195
CONTROL CHANGE 198
GPI 271
FADER START 274
BUS SETUP 252
SURROUND SETUP 214
CONSOLE LOCK 238
DATE/TIME 254
NETWORK 255
DANTE SETUP 257
SCENE
SCENE LIST 97
GLOBAL PASTE 103
Fade time 107
SONG SELECT 111
FOCUS RECALL 105
RECORDER
USB 200
NUENDO LIVE 209
CH JOB
CH LINK MODE 86
DCA GROUP ASSIGN 75
MUTE GROUP ASSIGN 80
RECALL SAFE MODE 83
CH COPY MODE 90
CH MOVE MODE 92
CH DEFAULT MODE 93
SETUP PATCH
PORT SELECT
26, 28, 117, 125,
174, 250
CH SELECT 23, 142, 201
Others
CONFIRMATION 223
SOFT KEYBORD (21)
LOGIN 218
Startup Menu
MODE SELECT 278
INITIALIZE ALL MEMORIES 278
INITIALIZE CURRENT MEMORIES 278
TOUCH SCREEN CALIBRATION 278
INPUT PORT TRIM 280
OUTPUT PORT TRIM 280
SLOT OUTPUT TRIM 280
FADER CALIBRATION 279
LED COLOR CALIBRATION 281
SELECTED CHANNEL section
V5 Reference Manual
6
SELECTED CHANNEL section
The SELECTED CHANNEL section located at the left of the display corresponds to a channel
module of a conventional analog mixer, and allows you to use the knobs on the panel to set
all the major parameters of the currently-selected channel.
Operations in this section will affect the channel that was most recently selected by its [SEL]
key. If you have assigned an ST IN channel or STEREO channel to a single channel strip,
either the L or the R channel will be selected, and the major parameters for L and R channels
will be linked.
Operations in the SELECTED CHANNEL Section
Follow the steps below to perform operations in the SELECTED CHANNEL section.
NOTE
To select a MIX or MATRIX channel, use the Bank
Select keys to recall the desired channel to the
Centralogic section, and then press the [SEL] key for
the desired channel.
The number and name of the currently-selected
channel is shown in the channel select field located in
the Function Access Area of the touch screen.
If an ST IN channel or STEREO channel has been
assigned to a single channel strip, you can switch
between L and R by repeatedly pressing the same
[SEL] key.
You can also switch channels by pressing the channel
select field located in the Function Access Area.
Press the left side of the field to select the preceding channel. Press the right side of the field to
select the next channel.
If you have turned on the option “POPUP APPEARS WHEN KNOB(S) PRESSED” on the
PREFERENCE tab (accessed by pressing the SETUP button, then the USER SETUP button),
pressing a knob repeatedly will open or close the screen (1 ch).
Even if a different screen is selected, the channel selected with the
[SEL] key can be set using the knobs of the SELECTED CHANNEL
section. In this case, a window indicating the value of that parameter will
appear on screen when you operate a knob.
STEP
1. Use the [SEL] key in the top panel INPUT section, ST IN section, or the STEREO/
MONO section, to select the channel to control.
2. Press one of the knobs in the SELECTED CHANNEL section.
3. Use the knobs of the SELECTED CHANNEL section and the buttons in the SELECTED
CHANNEL VIEW screen to edit the parameters of the selected channel.
Channel number
Channel name
SELECTED CHANNEL section
V5 Reference Manual
7
SELECTED CHANNEL VIEW screen
SEND field
In this field, you can view the send level and pre/post from the channel
to each MIX/MATRIX bus. You can also switch the on/off status of the
send signals. The view and the function of the knobs and buttons in
the SEND field vary depending on whether a pair of bus channels
(odd-numbered and even-numbered) are comprised of two mono
channels or a stereo channel.
1 Tabs
Enable you to select a group of 16 output bus channels to be
displayed in the SEND field.
MIX1-16 tab............................ displays MIX buses 1-16.
MIX17-24/MATRIX tab ........... displays MIX buses 17-24 and
MATRIX buses 1-8.
If the destination bus channels are two mono channels:
1 SEND knob
Adjusts the send level to the corresponding bus.
2 PRE indicator
The type of the corresponding bus is indicated. If the type is VARI [PRE EQ] or VARI [PRE
FADER], and if the PRE button on the MIX SEND 8ch screen is turned ON, the type is
displayed.
3 ON button
Switches the send signal to the corresponding bus on or off.
If the destination bus is a stereo channel:
1 SEND/PAN knob
The right-hand knob adjusts the level of the signal sent to a pair of bus channels (even-
numbered and odd-numbered). The left-hand knob adjusts the pan and balance of the
same signal.
2 PRE indicator
The type of the corresponding bus is indicated.
3 ON button
Switches the send signal to the two buses on or off.
NOTE
If the type of the destination bus is set to FIXED, controllers 2 and 3 mentioned above will not
be displayed.
Press the SEND knob or PAN knob on screen to open the SEND 8ch window.
1
1
2
3
1
2
3
SELECTED CHANNEL section
V5 Reference Manual
8
When using CUE B
Indicates that channels 7 and 8 on the MATRIX
bus are combined with CUE B.
NOTE
For details about how to use CUE B, see the
CUE screen (When configuring CUE B).
GAIN/PATCH field
This field enables you to make HA (head amp) analog or digital gain settings. You can also
view the operational status of the head amp.
1 GAIN knob
Sets the analog gain/digital gain of the head amp.
Press the knob to open the GAIN/PATCH 1ch window.
2 GC indicator
Indicates the fixed gain value output to the audio
network if the Gain Compensation function is turned
on.
3 OVER indicator
Warns you when the signal is clipping.
4 Ø (Phase) indicator
Indicates the status of the phase setting.
5 +48V indicator
Indicates the phantom power (+48V) on or off status for the head amp.
6 HPF ON indicator
Indicates the HPF on/off status of the external head amp.
7 AG-DG LINK indicator
Indicates a link between the analog gain and digital gain of the head amp.
8 Digital/Analog gain value
If analog gain is assigned to the GAIN knob, the digital gain value is shown here. If digital
gain is assigned to the GAIN knob, the analog gain value is shown here.
NOTE
For an input channel that is patched to an input that has no head amp, 1, 2, 5, 6, and 7
will not be shown. For an output channel,
1 - 7 will not be shown.
If a GAIN KNOB FUNCTION is set to DIGITAL GAIN in the USER SETUP PREFERENCE
screen, the digital gain knob will appear for
1, and 2, 5, 6, and 7 will not be displayed.
The display will change depending on the device.
For details, refer to “HA (head amp) settings” (page 32).
If patched to a wireless mic (SELECTED CHANNEL VIEW screen)
1 RX.GAIN knob/TX.GAIN knob/TX.ATT knob
Sets the gain for the transmitter or receiver. Press the knob
to open the GAIN/PATCH 1ch window.
The name of knob will change depending on the connected
device.
NOTE
When remote control connection is disabled for the connected
device, a gray circle is displayed here instead of a knob, and the
gain cannot be adjusted.
2 OL indicator
Lights if the audio signal level of the receiver reaches the overload point.
3 RF (Radio Frequency) signal meter
Shows bars to indicate the level of the RF signal. An active antenna indicator is shown
on the right side. It indicates which antenna is enabled.
NOTE
The display will change depending on the device.
For more information about the relationship between the number of bars and the actual strength
of the RF signal, refer to the manual from each developer.
4 Battery indicator
Shows bars to indicate the remaining battery power.
NOTE
For more information about the relationship between the number of bars and maximum operation
time, refer to the manual from each developer.
5 MUTE indicator
Indicates the mute status (on/off) of the audio signal for the receiver.
6 Frequency
Indicates the frequency that is currently set for the RF signal.
41
76
3
5
8
2
1
2
3
6
5
4
SELECTED CHANNEL section
V5 Reference Manual
9
PAN/BALANCE field
This field enables you to switch the on/off status of the signal sent from the selected channel
to the STEREO/MONO bus, and adjust the pan and balance.
The view and the function of the controllers in this field vary depending on the type of the
selected channel.
When an input channel or MIX channel is selected:
1 TO STEREO PAN knob
Sets the pan position of a signal routed to the
STEREO bus.
Press the knob to open the STEREO/MONO 8ch
window. If the ST IN channel is selected, you can
specify whether to view the PAN knob or the
BALANCE knob in this window. For a MIX channel,
the PAN knob will appear if the signal is mono, and the BALANCE knob will appear if the
signal is stereo.
NOTE
For mono input channels, the pan level is nominal at center and +3dB when panned either left or
right. These levels do not change even if channel link is used.
For ST IN channels, if the PAN knob is selected, the pan level is nominal when panned either left
or right and -3dB at center. If the BALANCE knob is selected the balance level is nominal at
center and +3dB when panned either left or right. These levels do not change even if channel link
is used.
2 ST/MONO button
Switches the on/off status of a signal sent from the
channel to the STEREO/MONO bus.
If an INPUT/MIX channel is set to LCR mode, the
LCR button appears in location
2.The LCR button
is an overall on/off switch for the signals sent from
the channel to the STEREO/MONO bus.
When a MATRIX, STEREO, or MONO channel is selected:
1 BALANCE knob
If the signal on the selected channel is stereo, the
BALANCE knob will appear, enabling you to adjust
the volume balance for the left and right channels.
If the channel signal is monaural, the BALANCE
knob is not shown and cannot be used.
Press the knob to open the TO STEREO 8ch
window.
When using Surround mode (MIX1- MIX6)
3 DOWN MIX
This field enables you to view the downmix
coefficient and L/R button settings.
Press this field to open the TO STEREO/MONO
window.
INPUT DELAY field
This field enables you to view the delay settings.
1 ON indicator
Indicates the on/off status of the delay.
2 Delay time
The delay value is displayed by milliseconds (ms) and also by currently-selected scale. If
the scale uses units of ms, the value in the bottom row will not be displayed. Only the
ms value appears in the middle row.
Press this field to open the INPUT DELAY 8ch window.
HPF field (input channels only)
This field enables you to set the HPF. If an output channel
is selected, a gray circle will appear in location
1, and 2
will not be displayed.
1 HPF knob
Sets the HPF cutoff frequency.
2 ON button
Switches the HPF on or off.
1 2
2
1
3
1
2
SELECTED CHANNEL section
V5 Reference Manual
10
EQ parameter field
This field displays the 4-band EQ parameter settings. Press each
knob to open the HPF/EQ 1ch window.
1 Q knob
Specifies the Q for each band.
If the HIGH band filter type is set to LPF or H.SHELF (high-
shelving), or the LOW band filter type is set to L.SHELF (low-
shelving), the Q knob will not be displayed. Only the filter
type name will be displayed.
NOTE
Fully rotating the HIGH band Q knob on the panel counter-
clockwise while pressing and holding it down will set the filter
type to LPF. Fully rotating the Q knob clockwise while pressing
and holding it down will set the filter type to high-shelving.
Fully rotating the LOW band Q knob on the panel clockwise while
pressing and holding it down will set the filter type to low-
shelving.
If an output channel has been selected, fully rotating the LOW
band Q knob on the panel counter-clockwise while pressing and holding it down will set the filter
type to HPF.
You can also switch the filter type in the HPF/EQ 1ch window.
2 FREQUENCY knob
Sets the center frequency (or cutoff frequency) for each band.
3 GAIN knob
Sets the amount of cut/boost for each band.
NOTE
If the HIGH band filter type is set to LPF, you can switch LPF on or off using the HIGH band GAIN
knob on the panel.
If the LOW band filter type is set to HPF, you can switch HPF on or off using the LOW band GAIN
knob on the panel.
NOTE
When the BYPASS button is on, the knobs turn gray.
EQ graph field
This field graphically indicates the approximate response of the EQ. Press this field to open
the HPF/EQ 1ch window, in which you can set the attenuator, HPF, and EQ.
DYNAMICS1/DYNAMICS2 field
This field enables you to set the Dynamics 1/2 parameters.
1 OVER indicator
Warns you when the signal is clipping.
2 Level meter
Displays the output signal level (green) and the amount of gain reduction (orange)
when the Dynamics is on. The current threshold setting is shown as a white vertical line.
3 Threshold
Specifies the threshold.
4 Parameters
Indicate the values of parameters that vary depending on the currently-selected
dynamics type.
Press this field to open the DYNAMICS 1/DYNAMICS 2 1ch window, in which you can
make detailed parameter settings.
1 2 3
1 2
3
4
SELECTED CHANNEL section
V5 Reference Manual
11
INSERT field
This field enables you to make insert settings.
1 Popup button
Press this button to open the INSERT/DIRECT OUT
1ch window.
2 ON button
Switches the insert on or off.
3 RACK EDIT button
Appears if an effect or Premium Rack is inserted. Press this button to display the edit
screen for the inserted rack.
4 IN indicator
Appears if a port has been assigned to the insert-in patch. It lights when the signal is
sent to the insert-in.
DIRECT OUT field
This field enables you to make Direct Out settings.
1 Popup button
Press this button to open the INSERT/DIRECT OUT 1ch
window. The Direct Out level value will appear below the
button.
2 ON button
Switches the Direct Out on or off.
RECALL SAFE field
This field enables you to make Recall Safe settings.
1 Popup button
Press this button to open the RECALL SAFE window.
2 ON button
Switches the Recall Safe status on or off.
3 PARTIAL indicator
Lights only if some of the channel parameters are set to Recall Safe.
FADER field
This field enables you to make settings for the channel on/off
status and the level.
1 Fader
Displays the current level.
Use the faders on the top panel to set the levels.
2 Level indicator
Displays the current level setting by numerical value. If
the signal is clipping at any point in the channel, the Σ
CLIP indicator will light.
3 ON button
Switches the channel on and off. The button is linked
with the corresponding [ON] key on the top panel.
NOTE
For CL V2.0 and later, the TOUCH AND TURN function
assigned to one of the USER DEFINED knobs enables you
to control the fader in the FADER field of the SELECTED
CHANNEL VIEW screen.
4 CUE SETTINGS button
Use this button to open the CUE SETTINGS screen.
DCA/MUTE field
This field enables you to select the DCA or mute group to which the
channel is assigned.
1 Tabs
Select a DCA or mute group. Press the selected tab once again
to open the DCA/MUTE GROUP ASSIGN MODE window.
When the DCA group tab is selected:
2 DCA group select buttons
Select the DCA group to which the channel is assigned.
3 Mute group indicators
Indicate the mute group to which the channel is assigned.
1
2
43
21
2
1
3
1
2
3
4
When two channels are
used for CUE, and
CUE OPERATION MODE
is set to CH
1
3
2
SELECTED CHANNEL section
V5 Reference Manual
12
When the mute group tab is selected:
4 Mute group select buttons
Select the mute group to which the channel is assigned.
NOTE
If the dimmer level is set to the mute group, this button lights
orange.
5 SAFE button
Temporarily removes the channel from the mute group.
6 DCA group indicators
Indicate the DCA group to which the channel is assigned.
4
5
6
Centralogic section
V5 Reference Manual
13
Centralogic section
The Centralogic section located below the touch screen lets you recall and simultaneously
control a set of eight input channels, output channels, or DCA groups. If you press one of the
Bank Select keys, the channels or DCA groups corresponding to that key will be assigned to
the Centralogic section, and can be controlled using the faders, [ON] keys, and [CUE] keys in
the Centralogic section.
Operations in the Centralogic section
NOTE
When the SELECTED CHANNEL VIEW screen is displayed, you can switch to the OVERVIEW
screen by pressing any of the multifunction knobs 1-8. This is convenient when you want to
quickly switch to the OVERVIEW screen while leaving the same channels or DCA groups
selected for control.
The bottom line of the OVERVIEW screen shows the channels or DCA groups that can be
controlled by the faders, [ON] keys and [CUE] keys of the Centralogic section.
The top line of the OVERVIEW screen shows the channels that can be controlled by multifunction
knobs 1 - 8 in the Centralogic section.
Bank Select keys
STEP
1. Use the Bank Select keys in the Centralogic section to select the channels or DCA
groups that you want to control.
2. Use the faders and [ON] keys of the Centralogic section to adjust the level of the (up
to) eight selected channels and switch them on/off.
3. Use the fields on the OVERVIEW screen and the multifunction knobs to adjust the
parameters for the group of up to eight channels.
Centralogic section
V5 Reference Manual
14
OVERVIEW Screen
CHANNEL NAME field
This field appears at the top and bottom of the screen and displays the channel number,
name, and icon for the currently-selected eight channels. The name of the currently-selected
channel is highlighted.
NOTE
If you have retained a specific channel (that is controlled by the faders or knobs in the Centralogic
section) by pressing and holding down the corresponding Bank Select key, the channel name
display at the top of the channel strip graphic may differ from the name displayed at the bottom
of the same channel strip.
GAIN/PATCH field
This field enables you to make HA (head amp) analog or digital gain settings. You can also
view the operational status of the head amp.
The view and the function of the controllers in this field vary depending on the type of the
selected channel.
If the head amp is patched:
1 GAIN knob
Sets the analog gain of the head amp.
Press this field to assign the GAIN knob to the corresponding multifunction knob in the
Centralogic section, which enables you to adjust the gain. If the Gain Compensation
function is turned on, an indicator appears, showing the level of the signal output to
the audio network.
If the GAIN knob has been assigned to a multifunction knob, press the knob to open
the GAIN/PATCH 8ch window.
2 OVER indicator
Lights when a signal at the input port or from the rack output exceeds the full scale level.
This indicator is available only if an input channel is selected.
3 +48V indicator
Indicates the phantom power (+48V) on or off status for the head amp. This indicator is
not displayed unless the head amp is patched to the channel.
4 Ø (Phase) indicator (input channels only)
Indicates the input phase setting for the head amp
NOTE
If the slot is not connected to the head amp, the patch and the type of the MY card will be
displayed.
If GAIN KNOB FUNCTION is set to DIGITAL GAIN in the PREFERENCE screen, the DIGITAL
GAIN knob will appear instead of knob
1, and indicator 3 will not be displayed.
Press the SETUP button, then the USER SETUP button, select the PREFERENCE tab, and then
set the GAIN KNOB FUNCTION to DIGITAL GAIN. You will be able to adjust the digital gain value
by using a multifunction knob.
You can also operate the digital gain by assigning INPUT GAIN DIGITAL GAIN to a USER
DEFINED knob, or by assigning an ALTERNATE function to a USER DEFINED key and then
adjusting the USER DEFINED knob or the GAIN knob for the selected channel while
ALTERNATE is on.
: Selected channel
: Unselected channel
1
4
3
2
Centralogic section
V5 Reference Manual
15
If patched to a wireless mic (OVERVIEW screen)
1 RX.GAIN knob/TX.GAIN knob/TX.ATT knob
Sets the gain for the transmitter or receiver.
Press this field to assign the GAIN knob to the corresponding multifunction knob in the
Centralogic section, which enables you to adjust the gain.
If the GAIN knob has been assigned to a multifunction knob, press the knob to open
the GAIN/PATCH 8ch window.
The name of knob will change depending on the connected device.
NOTE
When the remote control connection is disable to the connected device, a gray circle is displayed
here instead of a knob, and the gain cannot be adjusted.
2 RF (Radio Frequency) signal meter
Shows bars to indicate the level of the RF signal. An active antenna indicator is shown
on the right side. It indicates which antenna is enabled.
NOTE
The display will change depending on the device.
For more information about the relationship between the number of bars and the actual strength
of the RF signal, refer to the manual from each developer.
3 Battery indicator
Shows bars to indicate the remaining battery power.
NOTE
For more information about the relationship between the number of bars and maximum operation
time, refer to the manual from each developer.
4 OL indicator
Lights if the audio signal level of the receiver reaches the overload point.
NOTE
If the audio signal for the receiver is muted, 5 is displayed.
5 MUTE indicator
Displayed only if the audio signal for the receiver is muted.
NOTE
If the audio signal for the receiver is not muted, 4 is displayed.
INPUT DELAY field (input channels only)
This field displays the delay status for the input channel. Press this field to open the INPUT
DELAY 8ch window.
1 DELAY ON/OFF indicator
Indicates the on/off status of the delay.
INSERT/DIRECT OUT field
This field displays the Insert/Direct out status. Press this field to open the INSERT/DIRECT
OUT 8ch window.
1 INSERT ON/OFF indicator
Indicates the insert on/off status.
2 DIRECT OUT ON/OFF indicator (input channels only)
Indicates the Direct Out on/off status.
1 2
3 4 5
If the slot is patched:
The slot name will appear.
If the rack is connected:
The patch and module name will appear.
If the output is connected:
Only the patch will appear.
1
1
2
Centralogic section
V5 Reference Manual
16
EQ field
This field graphically indicates the approximate response of
the EQ. Press this field to open the HPF/EQ 1ch window, in
which you can set the HPF and EQ.
NOTE
If DCA or monitor has been selected, this field will be blank.
DYNAMICS 1/2 field
This field displays the threshold value and meter for Dynamics
1/2. Press this field to open the DYNAMICS 1/2 1ch window.
NOTE
If DCA or monitor has been selected, this field will be blank.
SEND field
This field displays the send level, send on/off status, and pre/post
settings for 16 buses.
To select the 16 destination buses, use the [MIX 1-16] key/[MIX 17-24/
MATRIX] key in the SELECTED CHANNEL section.
To adjust the send level for each bus, use the SEND knob of the
SELECTED CHANNEL section
This field varies depending on the type of the destination bus.
If the destination bus is VARI (mono):
The knob color and scale color indicate the send on/off and pre/post
status. If the send is off, the knob color turns gray. With the post setting,
the knob scale color turns black.
If the destination bus is VARI (stereo):
If a pair of buses (odd-numbered and even-numbered) are in stereo, the
left-hand knob will function as the PAN knob, and the right-hand knob will
function as the SEND knob.
If the destination bus is set to FIXED:
The SEND ON/OFF button for each bus is shown instead of the knob.
Centralogic section
V5 Reference Manual
17
TO STEREO/MONO field
This field displays the on/off status and pan/balance setting of the signal sent to the STEREO/
MONO bus.
This field varies depending on the type of the selected channel.
When an input channel or MIX channel is selected:
1 TO STEREO PAN knob
Sets the pan position of a signal routed to the STEREO bus.
Press the knob to open the STEREO/MONO 8ch window. If the ST IN channel is selected,
you can specify whether to view the PAN knob or the BALANCE knob in this window.
For a MIX channel, the PAN knob will appear if the signal is mono, and the BALANCE
knob will appear if the signal is stereo.
2 ST/MONO indicator
Indicates the status of a signal sent to the STEREO/MONO bus.
If an input or MIX channel is set to LCR mode, the LCR indicator
will be displayed.
When a MATRIX channel (monaural) or MONO channel is selected:
The Σ CLIP indicator will light if the signal is clipping at some point in the channel.
For a stereo MATRIX channel or STEREO channel, the BALANCE knob appears, indicating
the balance of the left/right channels.
DCA group field
A DCA group (1-16) to which the channel is assigned is displayed on the first or second row
in this field.
Press this field to open the DCA/MUTE GROUP ASSIGN MODE window.
Mute group field
A mute group (1-8) to which the channel is assigned is displayed on the third row in this field.
If the channel has been temporarily removed from the mute group, S (Safe) will appear on the
third row. If a dimmer level has been specified for a mute group, the color of the characters will
change from red to orange.
Press this field to open the DCA/MUTE GROUP ASSIGN MODE window.
1
2
2
Input and output patching
V5 Reference Manual
18
Input and output patching
This chapter explains how to edit the input patching and output patching, how to connect
inserts, and how to use direct outputs.
When the CL series is in the initial state, the following input ports (jacks/ports) are patched to
each input channel.
For CL5
For CL3
For CL1
When the CL is in the initial state, the output ports (jacks/ports) are patched to the following
output channels.
CL console internal patching and Dante audio
network patching
The following diagram shows the signal flow through the CL series console, I/O devices, and
Dante audio network.
Input channels Input port (jack/port)
CH1-48 DANTE1-48
CH49-64 DANTE49-64
CH65-72 OMNI1-8
ST IN 1L-8R FX 1L(A)-FX 8R(B)
Input channels Input port (jack/port)
CH1-48 DANTE1-48
CH49-64 DANTE49-64
ST IN 1L-8R FX 1L(A)-FX 8R(B)
Input channels Input port (jack/port)
CH1-48 DANTE1-48
ST IN 1L-8R FX 1L(A)-FX 8R(B)
Output port (jack/port) Output channels
DANTE1-24 MIX 1-24
DANTE25-32 MATRIX1-8
DANTE33-34 STEREO L/R
DANTE35 MONO
DANTE36-37 MONITOR L/R
DANTE38 MONITOR C
DANTE39-40 CUE L/R
DANTE41-64 NO ASSIGN
SLOT1 (1)-(16) MIX1-16
SLOT2 (1)-(8) MIX17-24
SLOT2 (9)-(16) MATRIX1-8
SLOT3 (1)-(2) STEREO L/R
SLOT3(3) MONO
SLOT3 (4)-(5) MONITOR L/R
SLOT3(6) MONITOR C
SLOT3 (7)-(8) CUE L/R
SLOT3 (9)-(16) NO ASSIGN
OMNI OUT 1 - OMNI OUT 6 MIX 1-6
OMNI OUT 7 - OMNI OUT 8 STEREO L/R
FX1L(A), FX2L(A), FX3L(A),
FX4L(A), FX5L(A), FX6L(A),
FX7L(A), FX8L(A)
MIX17, MIX18, MIX19, MIX20, MIX21, MIX22, MIX23,
MIX24
DIGITAL OUT L/R STEREO L/R
RECORDER INPUT L/R STEREO L/R
Output port (jack/port) Output channels
8 16 16 16 64
SW
Dante-MY16-AUD
ID #3
ID #1
ID #2
OMNI MY MY MY
INPUT PATCH
Dante Network
“Dante” (ports)
CL series
I/O Device
Dante
patching
CL series
internal
patching
I/O Device
I/O Device
Input and output patching
V5 Reference Manual
19
Input patching
CL series consoles and I/O devices feature two types of patching: Dante audio network
patching and CL console internal patching.
For Dante audio network patching, you will use the DANTE INPUT PATCH window. In this
window, you can patch the CL console and I/O device inputs. Sixty-four (64) channels can be
input from a Dante audio network to a CL series console. You can choose up to 64 channels
from a maximum of 512 channels (logical value) of Dante audio network signals. Select the
I/O device (up to 64 channels) that you want to control from the CL series console.
Then, route the input signals (that were patched in the DANTE INPUT PATCH screen) to
channels on the CL series console. To do this, choose input ports from DANTE 1-64 in the
GAI N /PATCH s c re e n .
NOTE
By default, DANTE 1-64 are assigned to input channels 1-64.
Output patching
Use the OUTPUT PORT screen to patch the CL console’s output channels and Dante audio
network. In this window, assign output channel signals to DANTE 1-64 ports.
NOTE
By default, MIX 1 - 24 are assigned to DANTE 1 - 24, MATRIX 1 - 8 are assigned to DANTE 25
- 32, STEREO L/R are assigned to DANTE 33/34, and MONO is assigned to DANTE 35.
Next, patch the output signals from DANTE 1-64 (assigned in the OUTPUT PORT SETUP
screen) to I/O rack outputs. Use the OUTPUT PATCH screen of the I/O RACK to make these
assignments.
Changing the input patching
NOTE
You can also select an input port from the GAIN/PATCH screen.
STEP
1.
Use the Bank Select keys in the Centralogic section to select the input channels that
you want to control.
2. Press the channel number/channel name field on the OVERVIEW screen.
3. Select the type of port in the category select list on the PATCH/NAME screen, and
use the port select buttons to select the input port.
OVERVIEW screen PATCH/NAME screen
Input and output patching
V5 Reference Manual
20
PATCH/NAME screen
1 PATCH button
Indicates the currently-selected input port. If you press this button when selecting an
icon or changing the channel name, you will return to the input port select screen.
2 Icon button
Indicates the icon that is selected for the corresponding channel. When you press this
button, a screen will appear in which you can select an icon or sample name.
3 Channel name input box
Indicates the name that is assigned to the corresponding channel. When you press this
field, a keyboard window allowing you to change the channel name will appear.
4 Category select list
Selects the category of input port. The categories correspond to the following input
ports. The displayed categories vary depending on the channel type.
DANTE1-32 ............DANTE1 - DANTE32
DANTE33-64..........DANTE33 - DANTE64
OMNI/PB OUT .......OMNI 1 - OMNI 8, PB OUT (L), PB OUT (R)
SLOT1....................SLOT1(1) - SLOT1(16)
SLOT2....................SLOT2(1) - SLOT2(16)
SLOT3....................SLOT3(1) - SLOT3(16)
EFFECT RACK ......FX1L(A) - FX8R(B)
PREMIUM RACK...PR1L(A) - PR2R(B)
5 Port select buttons
Select the input port that is assigned to the currently-selected channel.
6 Channel name/Effect type indicator
NOTE
In categories other than DANTE IN, channel labels cannot be set in Dante Controller for the
following buttons, and therefore they are not displayed.
•MONITOR button
CUE button
SURROUND MONITOR button
•SLOT button
SEL CH button
SEND MASTER button
•OMNI button
7 Tabs
Enable you to switch between items.
8 Close button
Closes the screen.
2 83
1
7
4
5
6
Input and output patching
V5 Reference Manual
21
Changing the output patching
To change the patching, you can either select the output port that will be the output destination
of each output channel, or you can select the output channel that will be the output source for
each output port.
Selecting the output port for each output channel
PATCH/NAME screen
1 PATCH button
Indicates the port that is patched to the output channel. If you press this button when
another tab is active, a window will appear, enabling you to select the network and port.
2 Channel select button
Selects the channel to set.
NOTE
Switching channels on this screen will not affect the channel selection on the console.
3 Channel icon button
Indicates the icon and color that are currently selected for the corresponding channel.
When you press this button, a screen will appear in which you can select an icon or
sample name.
4 Channel number display box
Indicates the channel number. This item cannot be changed.
5 Channel name input box
Indicates the name that is assigned to the corresponding channel. When you press this
field, a keyboard window allowing you to assign a name will appear.
6 Category select list
Select the type of port.
STEP
1. Use the Bank Select keys in the Centralogic section to select the output channels.
2. Press the channel number/channel name field on the OVERVIEW screen.
3. Select the type of port in the category select list on the PATCH/NAME screen, and
use the port select buttons to select the output port.
OVERVIEW screen PATCH/NAME screen
3 54
1
9
6
7
2
8
Input and output patching
V5 Reference Manual
22
7 Port select buttons
From the category, these buttons let you select the port to patch. To cancel the
selection, press the button once again.
8 Tabs
Enable you to switch between items.
9 Close button
Closes the screen.
Selecting the output channel for each output port
NOTE
If PATCH CONFIRMATION in the PREFERNCE tab on the USER SETUP screen is ON, a
confirmation dialog box will appear when you attempt to change the patch settings. If STEAL
PATCH CONFIRMATION is ON, a confirmation dialog box will appear when you attempt to
change a location that is already patched elsewhere.
CH SELECT screen
1 Category select list
Select the category of the channel. The categories correspond to the following channels.
They vary depending on the output port type.
MIX/MATRIX ............................. MIX 1 - MIX 24, MATRIX 1 - MATRIX 8
ST/MONO/MONI/CUE .............. STEREO L, STEREO R, MONO (C), MONI L,
MONI R, MONI C, CUE L, CUE R, SMON L,
SMON R, SMON C, SMON LFE, SMON Ls,
SMON Rs, MMTX L, MMTX R, MMTX C, MMTX LFE,
MMTX Ls, MMTX Rs
DIRECT OUT 1-32 .................... CH 1 - CH 32 Direct Outs
DIRECT OUT 33-64.................. CH 33 - CH 64 Direct Outs
DIRECT OUT 65-72.................. CH 65 - CH 72 Direct Outs
INSERT 1 OUT 1-32 ................. CH1-CH32 Insert 1 Outs
INSERT 1 OUT 33-64 ............... CH33-CH64 Insert 1 Outs
INSERT 1 OUT 65-72 ............... CH65-CH72 Insert 1 Outs
INSERT 1 OUT MIX/MATRIX ... MIX1-MIX24, MATRIX1-MATRIX8 Insert 1 Outs
INSERT 1 OUT ST/MONO........ STEREO L, STEREO R, MONO (C) Insert 1 Outs
INSERT 2 OUT 1-32 ................. CH1-CH32 Insert 2 Outs
INSERT 2 OUT 33-64 ............... CH33-CH64 Insert 2 Outs
INSERT 2 OUT 65-72 ............... CH65-CH72 Insert 2 Outs
INSERT 2 OUT MIX/MATRIX ... MIX1–MIX24, MATRIX1–MATRIX8 Insert 2 Outs
INSERT 2 OUT ST/MONO........ STEREO L, STEREO R, MONO (C) Insert 2 Outs
CASCADE MIX/MATRIX........... MIX 1 - MIX 24, MATRIX 1 - MATRIX 8
CASCADE ST/MONO/CUE ...... STEREO L, STEREO R, MONO (C), CUE L, CUE R
STEP
1. In the Function Access Area, press the SETUP button.
2. Press the OUTPUT PORT button in the SYSTEM SETUP field located in the center of
the SETUP screen.
3. In the tabs below the OUTPUT PORT screen, select the output port you want to
control.
4. Press the channel select button of the port you want to operate.
5. Use the category select list and the channel select buttons to select the send-source
channel.
SETUP screen OUTPUT PORT screen
1
2
3
Input and output patching
V5 Reference Manual
23
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
2 Channel select button
Select the channel to be assigned to the output port from the current category.
3 CLOSE button
Closes the screen.
Inserting an external device into a channel
You can insert an effect processor or other external device into the signal path of an INPUT,
MIX, MATRIX, STEREO, or MONO channel. When doing so, the type of input/output port
used for the insertion and the location of the insertion in/out can be specified individually for
each channel.
NOTE
If you install a digital I/O card in a slot and digitally connect an external device, you must
synchronize the word clock of the CL console and the external device (page 246).
There is a limit to the sum of INSERT 1 and INSERT 2 for each channel group, as shown in the
table below. You can select any output or input ports.
* When using Surround mode
STEP
1. Connect your external equipment to an OMNI IN/OUT jack or to an I/O card
installed in slots 1 - 3.
2. Use the Bank Select keys in the Centralogic section to select the channel to which
you want to assign the input source.
3. Press the INSERT/DIRECT OUT field.
4. Press the INSERT OUT or INSERT IN button.
5. Select an output port or an input port.
6. Press the INSERT ON button.
CH1-16 CH17-32 CH33-48
CH49-64
(CL5 and
CL3
only)
CH65-72
(CL5
only)
MIX1-24/
ST/
MONO
MATRIX
1-8
INSERT
OUT
16 16 16 16 8 30(24)* 8
INSERT IN 16 16 16 16 8 30(24)* 8
OVERVIEW screen INSERT/DIRECT OUT Screen (8ch)
Input and output patching
V5 Reference Manual
24
If you exceed the INSERT OUT or INSERT IN limitation, the indicator will light up on the left.
If the limit is exceeded, invalid ports will be marked with a strike-out line.
If the limit is exceeded, the following ports will take priority per channel group (listed in the table
above).
1 INSERT 1 will take priority over INSERT 2.
2 Lower-number channel will take priority.
INSERT/DIRECT OUT screen (1ch)
INSERT field
This field enables you to make insert settings. Press one of three fields to choose PRE EQ
(immediately before the EQ), PRE FADER (immediately before the fader), or POST ON
(immediately after the [ON] key) as the insert position.
NOTE
You can set the I/O ports to function as an insert for each block.
1 INSERT OUT button
Displays the currently-selected output port for insert 1 and insert 2. Press this button to
open the PORT SELECT window, in which you can select an output port.
2 INSERT IN button
Displays the currently-selected input port for insert 1 and insert 2. Press this button to
open the PORT SELECT window, in which you can select an input port.
3 INSERT ON/OFF button
Switches the insert on or off.
4 APPLY TO ALL INPUT button (input channels only)
Specifies whether the insert position and direct out point setting will be applied to all
input channels.
5 APPLY TO ALL OUTPUT button (output channels only)
Specifies whether the insert point setting will be applied to all output channels.
NOTE
Insert 1 and insert 2 are serial connections with fixed sequential numbers.
1
2
3 < < 9
4
5
86 7
Input and output patching
V5 Reference Manual
25
INSERT IN HA field
This field will appear if you have selected an input port (that features a head amp) as the
insert-in.
6 +48V button
Switches head amp phantom power (+48V) (currently-selected for insert 1 and insert 2)
on or off.
7 A.GAIN knob
Indicates the currently-selected head amp analog gain setting for insert 1 and insert 2.
Press these knobs to control the parameter values using the multifunction knobs.
NOTE
If you have selected the OMNI IN jack on the CL console
as the input port for insert-in, make the HA settings in the
INSERT IN HA field.
Even if the INSERT ON/OFF button is OFF, the signal
selected for insert-out will continue to be sent.
8 HA meter
Displays the level of the currently-selected head amp input signal for insert 1 and insert
2.
9 Close button
Closes the screen.
0 Resource meter
Displays the number of used resources for each channel for INSERT IN and INSERT OUT.
NOTE
If surround mode is set on the CL series console, the INSERT resources for output channels
[MIX/ST MONO] are reduced from 30 to 24.
INSERT/DIRECT OUT screen (8ch)
1 Channel select button
Selects the channel to set. The channel icon, color, and number appear.
2 INSERT ON/OFF button
Switches the insert on or off. The currently-specified insert point setting appears above
the button.
3 INSERT OUT button
Indicates the currently-selected port. Press this button to open the PORT SELECT screen,
in which you can select an output port.
4 INSERT IN button
Indicates the currently-selected port. Press this button to open the PORT SELECT screen,
in which you can select an input port. You can also view the insert-in level by checking
the indicator located to the right of the this button.
1
4
3
2
Input and output patching
V5 Reference Manual
26
PORT SELECT screen
Displayed when you press either the INSERT OUT or INSERT IN button in the one-channel
or the eight-channel INSERT/DIRECT OUT window. Set the input/output port used for
insertion.
1 Category select list
Selects the category of port. The categories correspond to the following ports. The
displayed categories vary depending on the channel type.
OMNI...................................... OMNI1 - OMNI8
SLOT1.................................... SLOT1(1) - SLOT1(16)
SLOT2.................................... SLOT2(1) - SLOT2(16)
SLOT3.................................... SLOT3(1) - SLOT3(16)
GEQ RACK ............................ GEQ1L(A) - GEQ16R(B)
(MIX/MATRIX/STEREO/MONO channels only)
GEQ1L(A) - GEQ8R(B) (INPUT channels only)
EFFECT RACK ...................... FX1L(A) - FX8R(B)
PREMIUM RACK ................... PR1L(A) - PR8R(B)
2 Port select buttons
Assign the port that will be used as insert-out/insert-in for the currently-selected
channel.
NOTE
If a rack in which a GEQ, PEQ, or Premium Rack is mounted is specified as the insert-out or
insert-in, the other patch point will automatically be assigned to the same rack. Also, insert mode
will automatically be switched on. Additionally, if you defeat the insert-out or insert-in of a rack in
which a GEQ, PEQ, or Premium Rack is mounted, the other patch point will automatically be
defeated and at the same time insert mode will automatically be switched off.
3 CLOSE button
Closes the screen.
Directly outputting an INPUT channel
The signal of an INPUT channel can be output directly from an OUTPUT jack on the I/O
device, from the desired OMNI OUT jack, or from the output channel of a desired slot.
NOTE
If you install a digital I/O card in a slot and digitally connect an external device, you must
synchronize the word clock of the CL console and the external device (page 246).
1
2
3
STEP
1. Connect your external device to an OMNI OUT jack, OUTPUT jack, or to an I/O card
installed in slot 1-3.
2. Use the Bank Select keys in the Centralogic section to select the input channel that
you want to output directly.
3. Press the INSERT/DIRECT OUT field in the OVERVIEW screen.
4. Press the DIRECT OUT PATCH button in the INSERT/DIRECT OUT screen.
5. Select an output port.
OVERVIEW screen INSERT/DIRECT OUT Screen (8ch)
Input and output patching
V5 Reference Manual
27
INSERT/DIRECT OUT screen (1ch)
1 DIRECT OUT field
Enables you to make settings for direct output. Press one of four fields to choose PRE HPF
(immediately before the HPF), PRE EQ (immediately before the EQ) or PRE FADER
(immediately before the fader), or POST ON (immediately after the [ON] key) as the direct
output position.
2 DIRECT OUT PATCH button
Displays the currently-selected Direct Out output port. Press this button to open the
PORT SELECT window, in which you can select an output port.
3 DIRECT ON button
Switches the Direct Out on or off.
4 DIRECT OUT LEVEL knob
Indicates the output level of the Direct Out. Press this button to control the level using
the multifunction knob.
5 APPLY TO ALL INPUT button (input channels only)
Specifies whether the insert point/Direct Out point settings will be applied to all input
channels.
6 Close button
Closes the screen.
INSERT/DIRECT OUT screen (8ch)
1 DIRECT ON button
Switches the Direct Out on or off. The currently-selected Direct Out point is indicated
above the button.
2 DIRECT OUT PATCH button
Displays the currently-selected Direct Out output port. Press this button to open the
PORT SELECT window, in which you can select an output port.
3 DIRECT OUT LEVEL knob
Indicates the output level of the Direct Out. Press this button to control the level using
the multifunction knob.
4 Close button
Closes the screen.
5
4
1
6
32
1
2
3
4
Input and output patching
V5 Reference Manual
28
PORT SELECT screen
Displayed when you press the DIRECT OUT PATCH button in the one-channel or the eight-
channel INSERT/DIRECT OUT window. Set the output port used for direct output.
1 Category select list
Selects the category of output port. The categories correspond to the following output
ports. The displayed categories vary depending on the channel type.
OMNI/REC .............OMNI1-OMNI8, REC IN(L), REC IN(R)
SLOT1....................SLOT1(1) - SLOT1(16)
SLOT2....................SLOT2(1) - SLOT2(16)
SLOT3....................SLOT3(1) - SLOT3(16)
DANTE1-32 ............DANTE1 - DANTE32
DANTE33-64..........DANTE33 - DANTE64
2 Output port select buttons
Assign the output port used for direct output of the currently-selected INPUT channel.
3 CLOSE button
Closes the screen.
1
2
3
Input channels
V5 Reference Manual
29
Input channels
This chapter explains various operations for input channels.
Signal flow for input channels
The input channels comprise the section that processes signals received from the I/O
devices, rear panel input jacks, or slots 1-3, and sends them to the STEREO bus, MONO bus,
MIX buses, or MATRIX buses. There are two types of input channels, as follows.
MONO channels
These channels are used to process monaural signals. When the CL series console is in the
default state, the input signal from the Dante connector is assigned.
STEREO channels
These channels are used to process stereo signals. When the CL series console is in the
default state, the input signal from the EFFECT RACK 1 - 8 is assigned.
•INPUT PATCH
Assigns input signals to the input channels.
Ø (phase)
Switches the phase of the input signal.
DIGITAL GAIN
Attenuates/boosts the level of the input signal.
HPF (High Pass Filter)
Cuts the region below the specified frequency.
4 BAND EQ (4 band equalizer)
A parametric EQ with four bands: HIGH, HIGH MID, LOW MID, and LOW.
DYNAMICS 1
This is a dynamics processor that can be used for gating and ducking, or as an expander
or compressor.
DYNAMICS 2
This is a dynamics processor that can be used as a compressor, compander, or de-esser.
•INPUT DELAY
Corrects input signal delay. You can specify up to 1000ms.
LEVEL/DCA 1-16
Adjusts the input level of the effect.
•ON (On/off)
Turns the input channel on or off. If this is off, the corresponding channel will be muted.
MIX
12 23
24
MATRIX
(USE 7-8
AS CUE B)
12 78
INPUT PATCH
ST
LR
M
O
N
O
(C)
CUE (A)
LR
CUE(A) L
CUE(A) R
CUE B R
CUE B L
TRIM
MIX
12 23
24
ST
LR
M
O
N
O
(C)
MATRIX
(USE 7-8
AS CUE B)
12 78 LR
INPUT PATCH
CUE(A) L
CUE(A) R
CUE B L
CUE B R
TRIM
CUE (A)
Input channels
V5 Reference Manual
30
•Pan
Adjusts the panning of signals sent from the input channel to the STEREO bus. For the
STEREO channel, you can switch between PAN and BALANCE. The BALANCE parameter
adjusts the volume balance of the left/right signals sent from the STEREO channel to the
STEREO bus. You can turn on PAN LINK in the BUS SETUP window so that the setting of
the PAN parameter will also be applied to signals sent to two MIX or MATRIX buses that
are set to stereo.
LCR (Left/Center/Right)
Sends the input channel signal to the STEREO bus/MONO bus as a three-channel signal
that consists of the L/R channels plus the center channel.
MIX ON/OFF (MIX send on/off)
This is an on/off switch for signals sent from the input channel to MIX buses 1 - 24.
MIX LEVEL 1-24 (MIX send levels 1-24)
Adjusts the send level of signals sent from the input channel to VARI type MIX buses 1 -
24. As the position from which the signal is sent to the MIX bus, you can choose from
the following: immediately before EQ, pre-fader, or post-fader.
MATRIX ON/OFF (MATRIX send on/off)
This is an on/off switch for signals sent from the input channel to MATRIX buses 1 - 8.
MATRIX LEVEL 1 - 8 (MATRIX send levels 1 - 8)
Adjusts the send level of the signal sent from the input channel to MATRIX buses 1 - 8.
As the position from which the signal is sent to the MATRIX bus, you can choose from
the following: immediately before the EQ, pre-fader, or post-fader.
INSERT (MONO channels only)
You can patch the desired output/input ports to insert an external device such as an
effect processor. For the position of the insert-out/insert-in point, you can choose
immediately before the EQ, immediately before the fader, or immediately after the [ON]
key.
DIRECT OUT (MONO channels only)
This can be patched to any output port, and the input signal sent directly from that
output port. For the position of the direct output, you can choose immediately before
the HPF, immediately before the EQ, immediately before the fader, or immediately after
the [ON] key.
METER
Indicates the input channel level. You can switch the position at which the level is
detected (page 135).
Specifying the channel name/icon
On the CL series unit, you can specify the on-screen name and icon for each input channel.
Here we will explain how to specify the channel name and icon.
STEP
1. Use the Bank Select keys in the Centralogic section to select the input channels.
2. Press the channel number/channel name field of the channel you want to specify on
the OVERVIEW screen.
3. Switch between items in the tabs on the PATCH/NAME screen, and specify a channel
name and icon.
OVERVIEW screen PATCH/NAME screen
Input channels
V5 Reference Manual
31
PATCH/NAME screen
When selecting the PATCH tab
1
PATCH button
Indicates the currently-patched port. If you press this button when another tab is active,
a window will appear, enabling you to select the network and port.
2 Icon button
Indicates the icon and color that are currently selected for the corresponding channel.
When you press this button, a screen will appear in which you can select an icon or
sample name.
3 Channel name input box
Indicates the currently-specified channel. When you press the inside of this box, the
SOFT KEYBOARD window will appear, enabling you to edit the channel name.
4 Tabs
Enable you to switch between items.
5 Close button
Closes the screen.
When selecting the ICON tab
1
Channel color select buttons
Select a channel color.
2 Icon select buttons
Select a channel icon.
3 Sample name setup buttons
Select a preset sample name. You can edit the name on the NAME tab later.
NOTE
You can also add or edit characters in the channel name field after you have entered the sample
name. If you want to quickly assign channel names that consist of a common name plus a
consecutive number, such as “Vocal 1” or “Vocal 2,” enter a sample name first, and then add a
number.
In CL V1.7 and later, you can set the channel color to black (OFF). The channel indicators on
channels for which black is selected will go off.
2 53
1
4
1
2
3
Input channels
V5 Reference Manual
32
When selecting the NAME tab
You can directly enter a channel name on the keyboard screen.
HA (head amp) settings
You can make HA (Head Amp) related settings (phantom power on/off, gain, phase) for the
input channel.
To adjust only the HA analog gain, use the GAIN knob in the SELECTED CHANNEL
section.
Setting the gain
Head amp settings are made in the GAIN/PATCH window.
NOTE
The PAD will be switched on or off internally when the HA gain is adjusted between +17 dB and
+18 dB.
Keep in mind that noise may be generated if there is a difference between the Hot and Cold
output impedance of the external device connected to the INPUT connector when using phantom
power.
The GAIN knob, +48V button, and Ø button are valid only on channels for which the assigned
input port is an INPUT jack on the I/O device, the OMNI IN on the CL unit, or a slot that is
connected to an external head amp device (e.g., Yamaha AD8HR or SB168-ES).
STEP
1. Use the Bank Select keys in the Centralogic section to select the channels.
2. Press the HA/PHASE field in the OVERVIEW screen.
3. Press the 1ch or 8ch tab in the GAIN/PATCH window.
4. Make settings for the head amp.
OVERVIEW screen GAIN/PATCH window (8 ch)
Input channels
V5 Reference Manual
33
GAIN/PATCH window (1 ch)
1 Channel icon/Channel number/Channel name indicator
Indicates the channel icon, number, and name.
2 HA section
Appears if the head amp is patched to the input channel.
NOTE
If a slot is patched to the channel, the type of the slot/MY card and the slot meter will be displayed.
If a rack is patched, the type of rack and type of effect will be displayed.
+48V button
Switches head amp phantom power (+48V) on or off.
A.GAIN (analog gain) knob
Indicates the analog gain of the head amp. Adjust the gain by using the
multifunction knobs. If the Gain Compensation function is turned on, an
indicator appears, showing the analog gain position at the time the
function was turned on.
•HA meter
Displays the level of the HA input signal.
GC (Gain Compensation) ON/OFF button
This button will display when a G.C. compatible device is patched.
Turns the Gain Compensation (gain correction function) on or off. If the Gain
Compensation function is turned on, the level of the signal output from the I/O device
to the audio network will be stabilized. For example, if the FOH console and the
monitoring console are sharing an I/O device, or if you are performing digital recording
via Dante connections, using this function will maintain the signal output at a constant
level from the I/O device to the network even if the analog gain value on the I/O device
is changed. If the Gain Compensation button is turned off, the compensation gain will
be reset, while the analog gain will return to the level that was obtained before you
turned on the button. Therefore, the signal level on the digital network will remain the
same.
Gain compensation meter
Indicates the level of the signal output to the audio network after gain compensation.
2 HA section (If patched to a wireless mic)
•Frequency
Indicates the frequency that is currently set for the RF signal.
Signal quality meter
Displays the quality of the received RF signal. The vertical axis represents quality and the
horizontal axis represents time, and the display of connection status is updated every
second. If you move away from the transmitter, or the quality of the RF signal decreases
due to the influence of disturbing radio waves, the bar indication becomes lower. It
displays in purple for Shure devices, and in white for the other developer’s devices.
RX.GAIN knob/TX.GAIN knob/TX.ATT knob
Sets the HA gain for the transmitter or receiver. The level meter located at the immediate
right of the knob indicates the input level.
The knob name will change depending on the connected device.
MUTE indicator
Indicates the mute status (on/off) of the audio signal for the receiver.
RF (Radio Frequency) signal meter
Shows bars to indicate the level of the RF signal.
An active antenna indicator is shown on the right side. It indicates which antenna is
enabled by lighting up.
NOTE
For more information about the relationship between the number of bars and the actual strength
of the RF signal, refer to the manual from each developer.
Battery indicator
Shows bars to indicate the remaining battery power.
NOTE
For more information about the relationship between the number of bars and maximum operation
time, refer to the manual from each developer.
32 4 5 6 7
01 8 9
Input channels
V5 Reference Manual
34
3 INPUT PORT button
Indicates the port that is assigned to the channel. Press this button to display the PORT
SELECT window, in which you can select a port to patch.
4 Icon / Channel name button
Indicates the channel number, icon, and name. Press this button to access the PATCH/
NAME window, in which you can patch the input port and specify the channel name.
5 AG-DG LINK button
If this button is turned on and GC (Gain Compensation) is enabled, you can link the
digital gain to the analog gain operation.
While you are controlling the analog gain, the Gain Compensation function enables you
to modify the level on your own console without affecting the level of other consoles.
6 D. GAIN (digital gain) knob
Indicates the digital gain value. Adjust the digital gain by using the multifunction knobs.
If the Gain Compensation function is turned on, digital gain will be used to adjust the
level of the signal input to the input channels.
7 Digital gain meter
Indicates the level after the signal passes through the digital gain.
8 GC ALL ON button/GC ALL OFF button
Switch Gain Compensation on or off for all input channels simultaneously.
9 Ø (Phase) button
Switches between normal and reverse phase settings of signals input from the head
amp.
0 AG-DG ALL ON/OFF buttons
You can turn on/off the link between the analog and digital gain for all input channels
simultaneously.
You can also view the link status in the SELECTED CHANNEL VIEW screen.
GAIN/PATCH window (8ch)
1 Channel select button
Indicates the channel icon, number, and name. When you press this button, the
corresponding channel will become a target for operations in the SELECTED CHANNEL
section, and the corresponding [SEL] key will light.
2 PATCH button
Press this button to display the PORT SELECT window to patch the input port to the
input channel.
: Link is on.
: Link is off.
1
2
3
6
8
4
5
97
Input channels
V5 Reference Manual
35
PORT SELECT window
TAKE FROM PORT button
The HA settings of the port will take priority. Even if you change the patching, the HA
settings of the port will remain unchanged.
TAKE FROM CHANNEL button
The HA settings of the channel will take priority. The HA settings of the port that had
been previously patched will be copied to the newly-patched port.
If the channel’s HA settings are selected, the following HA settings will be copied from
the channel to the port that is patched. If you patch the input channel from an input that
does not have these settings (i.e., that does not have a HA), the default values will be
specified.
NOTE
If youre newly patching a previously-unpatched input channel, the default values will be specified
if the HA INFO field’s TAKE FROM CHANNEL button is pressed.
3 HA section
Appears if the head amp is patched to the input channel.
NOTE
If the slot (for which the connection to the head amp is not recognized) is patched, the type of the
MY card will be displayed.
+48V button
This button will appear for the input channel to which the head amp has been patched.
Press the button to switch phantom power (+48V) on or off.
A.GAIN (analog gain) knob
Indicates the analog gain of the head amp. Press this knob to control the
parameter values using the multifunction knobs. If the Gain
Compensation function is turned on, an indicator appears, showing the
analog gain position at the time the function was turned on.
Level meter
Indicates the input signal level.
GC (Gain Compensation) button
Switches the Gain Compensation function on or off for that channel.
3 HA section (If patched to a wireless mic)
•Frequency
Indicates the frequency that is currently set for the RF signal.
RX.GAIN knob/TX.GAIN knob/TX.ATT knob
Sets the HA gain for the transmitter or receiver. The level meter located at the immediate
right of the knob indicates the input level. The knob name will change depending on
the connected device.
NOTE
When the remote control connection is disable to the connected device, a gray circle is displayed
here instead of a knob, and the gain cannot be adjusted.
For more information about the relationship between the number of bars and the actual strength
of the signal, refer to the manual from each developer.
MUTE indicator
Indicates the mute status (on/off) of the audio signal for the receiver.
HA setting Default value
HA gain amount -6dB
HPF on/off Off
Phantom power on/off Off
Gain compensation on/off Off
TAKE FROM PORT button
TAKE FROM CHANNEL button
Input channels
V5 Reference Manual
36
RF (Radio Frequency) signal meter
Shows bars to indicate the level of the RF signal.
An active antenna indicator is shown on the right side. It indicates which antenna is
enabled by lighting up.
NOTE
The display will change depending on the device.
For more information about the relationship between the number of bars and the actual strength
of the RF signal, refer to the manual from each developer.
Battery indicator
Shows bars to indicate the remaining battery power.
NOTE
For more information about the relationship between the number of bars and maximum operation
time, refer to the manual from each developer.
4 Ø (Phase) button
Switches between normal and reverse phase settings of signals input from the head
amp.
5 D. GAIN (digital gain) knob
Indicates the digital gain value. Press this knob to control the parameter values using the
multifunction knobs. If the Gain Compensation function is turned on, digital gain will
be used to adjust the level of the signal input to the input channels.
6 Digital gain meter
Indicates the level after the signal passes through the digital gain.
7 GC ALL ON button/GC ALL OFF button
Switch Gain Compensation on or off for all input channels simultaneously.
8 AG-DG LINK button
If this button is turned on and GC (Gain Compensation) is enabled, you can link the
digital gain to the analog gain operation.
While you are controlling the analog gain, the Gain Compensation function enables you
to modify the level on your own console without affecting the level of other consoles.
NOTE
If it is patched to a wireless mic, the battery indicator is displayed here.
9 AG-DG ALL ON/OFF buttons
You can turn on/off the link between the analog and digital gain for all input channels
simultaneously.
GAIN/PATCH window
(1-48, 49-72/ST IN (CL5), 49-64/ST IN (CL3), ST IN (CL1))
This window displays the head amp settings of the corresponding input channels. Here you
can also adjust the head amp gain in groups of the selected eight channels by using the
multifunction knobs in the Centralogic section.
1 Parameter select buttons
Switch parameters to view in the window.
ANALOG GAIN...................... Analog gain
DIGITAL GAIN ....................... Digital gain
PATC H ................................... Patch selection
2 GC ALL ON/GC ALL OFF buttons
Switch Gain Compensation on or off for all input channels simultaneously.
3 Channel select button
Selects the channel. You can select multiple channels simultaneously.
12 12
3
Input channels
V5 Reference Manual
37
If you press the ANALOG GAIN parameter select button:
1
GAIN knob
Indicates the analog gain setting for each channel. Press this knob to select a channel,
and then control the gain value using the multifunction knob. If the Gain Compensation
function is turned on, an indicator appears, showing the analog gain position at the time
the function was turned on.
2 OVER indicator
Lights when a signal at the input port or from the rack output exceeds the full scale level.
This indicator is available only if an input channel is selected.
3 +48V indicator
Indicates the +48V on/off status for each channel.
4 Ø (Phase) indicator
Indicates the phase setting for each channel.
NOTE
If the input channel is patched to a slot for which the connection to the head amp is not
recognized, the knob
1 will be replaced with the slot/port number of the patch destination. 3
will not be displayed.
If the input channel is patched to a rack, the knob
1 will be replaced with the port ID of the rack.
If nothing is patched to the input channel, the knob
1 will be replaced with a dotted line “----”.
If you press the DIGITAL GAIN parameter select button:
1
GAIN knob
Indicates the digital gain setting for each channel. Press this knob to select a channel,
and then control the gain value using the multifunction knob.
2 OVER indicator
Lights when a signal at the input port or from the rack output exceeds the full scale level.
This indicator is available only if an input channel is selected.
3 Ø (Phase) indicator
Indicates the phase setting for each channel.
If you press the PATCH parameter select button:
1
PATCH button
Press this button to open the PORT SELECT window, in which you can select an input
port to patch to the channel.
HA section (If patched to a wireless mic)
1
RX.GAIN knob/TX.GAIN knob/TX.ATT knob
Sets and displays and the gain for the transmitter or receiver. The knob name will change
depending on the connected device.
2 RF (Radio Frequency) signal meter
Shows bars to indicate the level of the RF signal. An active antenna indicator is shown
on the right side. It indicates which antenna is enabled.
NOTE
The display will change depending on the device.
For more information about the relationship between the number of bars and the actual strength
of the signal, refer to the manual from each developer.
3 Battery indicator
Shows bars to indicate the remaining battery power.
NOTE
For more information about the relationship between the number of bars and maximum operation
time, refer to the manual from each developer.
4 OL indicator
Lights if the audio signal level of the receiver reaches the overload point.
NOTE
When the receiver is muted, is displayed on the MUTE indicator.
1
3
2
4
1
2
3
1
2
3
1
4
Input channels
V5 Reference Manual
38
Relationship between analog and digital gain while Gain
Compensation is on
If Gain Compensation is on, adjusting the analog gain by a specific amount will cause the I/O
device to output to the audio network a signal that is attenuated by the same amount.
Therefore, the signals on the audio network will maintain a constant corrected level in the
digital domain.
For example, assume that the analog gain value has been set to +30 dB and Gain
Compensation is now turned on. Under this condition, if you raise the analog gain value to
+45 dB, the level of the signal sent to the audio network will stay at +30 dB (that is, attenuated
by -15 dB).
At this time, the gain of each signal input to the CL series console will be adjusted by the digital
gain parameter of the CL series console.
If the FOH console and the monitoring console are sharing one I/O device, adjusting the
analog gain on the FOH console will not affect the input level on the monitoring console,
because the level of the signal on the audio network is maintained at a constant level.
However, please note that if the signal is distorted due to a high level of analog gain, you must
first turn the Gain Compensation function off, set the gain to an appropriate input level, and
then turn the function back on. If you try to lower the analog gain level while the Gain
Compensation function is on, the signal on the audio network will be amplified by the same
amount due to the Gain Compensation function, and the signal will remain distorted.
NOTE
You can perform this operation by assigning the Gain Compensation on/off function to one of the
USER DEFINED keys.
Sending the signal from an input channel to the
STEREO/MONO bus
The STEREO bus and MONO bus are used to send signals to the main speakers. There are
two ways to send signals to the STEREO bus or MONO bus: ST/MONO mode and LCR
mode. You can select the mode individually for each channel. These two modes differ as
follows.
ST/MONO mode
This mode sends signals from the input channel to the STEREO bus and to the MONO bus
independently.
Signals sent from an input channel to the STEREO bus and to the MONO bus can be
switched on or off individually.
The panning of a signal sent from an input channel to the STEREO bus L/R is controlled by
the TO ST PAN knob. (Signals sent to the MONO bus are not affected by this knob.)
The left/right volume balance of a signal sent from an ST IN channel to the STEREO bus is
controlled by this knob.
If PAN/BALANCE mode is set to PAN, you will be able to adjust the pan position of signals
sent to the STEREO bus L/R individually (page 40).
LCR mode
This mode sends input channel signals to three buses (STEREO (L/R) and MONO (C))
simultaneously.
Signals sent from an input channel to the STEREO bus and MONO bus will be switched on
or off collectively.
The CSR (Center Side Ratio) knob specifies the level ratio between signals sent from an
input channel to the STEREO (L/R) bus and to the MONO (C) bus.
The TO ST PAN knob/BALANCE knob specifies the level of signals sent from an input
channel to the STEREO (L/R) bus and MONO (C) bus.
NOTE
If you want to monitor the signal of the STEREO bus or MONO bus through headphones or
similar devices, press the MONITOR button in the Function Access Area to select “LCR” as the
monitor source before you continue with the following procedure.
Input channels
V5 Reference Manual
39
STEP
1. Set the phantom power, gain, and phase of the input channel from which you want
to send the signal to the STEREO/MONO bus.
2. Use the Bank Select keys in the Centralogic section to select the input channel from
which you want to send the signal to the STEREO/MONO bus.
3. In the STEREO/MONO field, press a knob to select the channel you want to adjust in
the OVERVIEW screen, and then press the knob once again.
4. Use the MODE select button in the TO STEREO/MONO window to select either ST/
MONO mode or LCR mode for each channel.
5. In the MASTER section on the top panel, turn on the [ON] key for the STEREO
channel/MONO channel, and then raise the fader to an appropriate level.
6. In the INPUT section on the top panel, turn on the [ON] key for the input channel
you want to control, and then raise the fader to an appropriate position.
The subsequent steps will differ depending on whether ST/MONO mode or LCR mode was
selected for the channel in step 4.
Channels for which ST/MONO mode is selected
7. In the TO STEREO/MONO window, use the STEREO/MONO button to turn on/off
the signal sent from the input channel to the STEREO bus / MONO bus.
8. Use the TO ST PAN knob to set the panning of a signal sent from the input channel
to the STEREO bus.
Channels for which LCR mode is selected
7. In the TO STEREO/MONO window, use the LCR button to turn signals sent from the
input channel to the STEREO bus/MONO bus on or off collectively.
8. Use the CSR knob to adjust the level difference between the signals sent from that
channel to the STEREO (L/R) bus and to the MONO (C) bus.
9. Use the TO ST PAN knob to specify the panning of signals sent from the input
channel to the STEREO (L/R) bus and MONO (C) bus.
OVERVIEW screen TO STEREO/MONO window
Input channels
V5 Reference Manual
40
TO STEREO/MONO window (8ch)
Here you can control the on/off and pan/balance settings of the signal sent from input
channels to the STEREO (L/R) bus and MONO (C) bus, in groups of eight channels.
1 Channel select button
Selects the channel. You can select multiple channels simultaneously.
2 Mode LEDs
The LED of the currently-selected mode will light.
3 MODE select button
For a MONO channel, the mode can be switched between ST/MONO and LCR. For a
STEREO channel, the mode can be switched between PAN and BALANCE.
4 ST/MONO buttons
These buttons are on/off switches for signals that are sent from each channel to the
STEREO bus/MONO bus when the MONO button is set to ST/MONO mode.
5 Σ clipping indicator
Lights to indicate a signal is clipping at some point in the channel.
6 TO ST PAN/TO ST BALANCE knob
For MONO channels, this acts as a PAN knob that adjusts the left/right panning of
signals sent to the STEREO bus. For STEREO channels, this acts as a PAN knob, and also
as a BALANCE knob that adjusts the volume of the left and right signals sent to the
STEREO bus. To adjust the value, press the knob to select it, and then operate the
corresponding multifunction knob.
7 Tabs
Enable you to switch between windows.
8 LCR button
If the MODE button is set to LCR mode, this button is displayed instead of
4. This
button is an overall on/off button for signals sent from a channel to the STEREO bus and
MONO bus. If this button is off, no signals will be sent from the corresponding input
channel to the STEREO bus or MONO bus.
9 CSR knob
Adjusts the relative level of signals sent from the channel to the STEREO (L/R) bus and
to the MONO (C) bus, in the range of 0 - 100%. To adjust the value, press the knob to
select it, and then operate the corresponding multifunction knob (page 42).
1
2
3
6
5
4
7
ST/MONO mode LCR mode
8
9
Input channels
V5 Reference Manual
41
Added pan function (Monaural input channels
only)
The pan setting for signals sent to the STEREO bus enables you to select PAN LAW settings.
You can select one of the following:
NOTE
The settings are also applied to the signals sent to the stereo MIX buses.
1 PAN LAW select button
This toggle button is used to set the PAN LAW for the Input Channel.
For CENTER NOMINAL For LR NOMINAL
NOTE
PAN LAW settings are also enabled in LCR mode. They are also enabled in Surround mode.
You can also check the status of PAN LAW settings in the window shown below. For channels
where the mark is on, PAN LAW is set to LR NOMINAL.
TO STEREO/MONO window (CH1-48, CH49-72/ST IN(CL5), CH49-64/ST IN(CL3), ST
IN(CL1))
OVERVIEW window (STEREO/MONO field)
SELECTED CHANNEL VIEW window (PAN/BALANCE field)
CENTER NOMINAL
The pan level is nominal at center and +3dB when panned 100%
either left or right.
LR NOMINAL
The pan level is -3dB at center and nominal when panned 100%
either left or right.
STEP
1. Select a monaural input channel.
2. In the STEREO/MONO field, press a knob to select the channel you want to adjust in
the OVERVIEW window, and then press the knob once again. Or, in the PAN/
BALANCE field, press a knob to select the channel you want to adjust in the
SELECTED CHANNEL window, and then press the knob once again.
3. Use the PAN LAW select button in the TO STEREO/MONO window to set the PAN
LAW for each channel.
1
Input channels
V5 Reference Manual
42
TO STEREO/MONO window
(CH 1-48, CH 49-72/ST IN (CL5), CH 49-64/ST IN (CL3), ST IN
(CL1))
Adjusts the status of a signal sent from the corresponding input channel to the STEREO/
MONO bus. Here you can also adjust the pan or balance in groups of the selected eight
channels.
1 Channel select button
Selects the channel. You can select multiple channels simultaneously.
2 Σ clipping indicator
Lights to indicate a signal is clipping at some point in the channel.
3 TO ST PAN/TO ST BALANCE knob
Adjusts the panning or balance.
To adjust the value, press the knob to select it, and then operate the corresponding
multifunction knob.
If the signal reaches the overload point at any meter detection point in that channel, the
Σ indicator to the right of the knob will light.
4 ST/MONO indicator
If a channel is set to ST/MONO mode, these indicators will individually indicate the on/
off status of signals sent from the channel to the STEREO bus/MONO bus.
If that channel is set to LCR mode, the LCR indicator will be displayed in this location.
The LCR indicator indicates the on/off status of all signals sent from that channel to the
STEREO bus/MONO bus.
Signal level when LCR mode is selected
If LCR mode is selected, the signal level sent to the STEREO (L/R) bus and MONO (C) bus
will vary according to the settings of the CSR knob and the TO ST PAN knob.
When the CSR knob is set to 0% (MONO channel)
The TO ST PAN knob operates as a conventional PAN knob, and no signal is sent to the
MONO (C) bus.
When the CSR knob is set to 0% (STEREO channel)
The TO ST BALANCE knob operates as a conventional BALANCE knob, and no signal is
sent to the MONO (C) bus.
1
2
3
4
CLR
TO ST PAN knob
Signal sent to the STEREO (L) bus
Signal sent to the STEREO (R) bus
Signal level
CLR
TO ST BALANCE knob
Signal sent from the STEREO (L)
channel to the STEREO (L) bus
Signal level
CLR
TO ST BALANCE knob
Signal sent from the STEREO (R)
channel to the STEREO (R) bus
Signal level
Input channels
V5 Reference Manual
43
When the CSR knob is set to 100%
When the CSR knob is set to 100% (ST IN channel)
Sending a signal from an input channel to a MIX/
MATRIX bus
The MIX buses are used mainly for the purpose of sending signals to foldback speakers on
stage, or to external effect processors. The MATRIX buses are used to produce a mix that is
independent of the STEREO bus or MIX buses, and is typically sent to a master recorder or
to a backstage monitoring system.
You can send a signal from an input channel to a MIX/MATRIX bus in the following three ways.
Using the Selected Channel section
With this method, you use the knobs in the SELECTED CHANNEL section to adjust the send
levels to the MIX/MATRIX buses. When using this method, signals sent from a specific input
channel to all MIX/MATRIX buses can be adjusted collectively.
Using the Centralogic section
With this method, you use the multifunction knobs in the Centralogic section to adjust the level
of signals sent to the MIX/MATRIX buses. When using this method, the signals sent from eight
consecutive input channels to a specific MIX/MATRIX bus can be adjusted simultaneously.
Using the faders (SENDS ON FADER mode)
With this method, you switch the CL series unit to SENDS ON FADER mode, and use the
faders on the top panel to adjust the level of signals sent to the MIX/MATRIX buses. When
using this method, signals sent from all input channels to a specific MIX/MATRIX bus can be
adjusted simultaneously.
CLR
PAN k no b
Signal sent to the MONO (C) bus
Signal sent to the STEREO (L) bus
Signal sent to the STEREO (R) bus
Signal level
CLR
TO ST BALANCE knob
Signal sent from the ST IN (L) channel to
the MONO (C) bus
Signal sent from the ST IN (L) channel to
the STEREO (L) bus
Signal level
CLR
TO ST BALANCE knob
Signal sent from the ST IN (R) channel to
the MONO (C) bus
Signal sent from the ST IN (R) channel to
the STEREO (R) bus
Signal level
Input channels
V5 Reference Manual
44
Using the Selected Channel section
This section explains how to use the knobs in the SELECTED CHANNEL section to adjust
the send levels of signals sent from a specific input channel to all MIX/MATRIX buses.
NOTE
If you want to monitor the signal being sent to a specific MIX/MATRIX bus, use the Bank Select
keys in the Centralogic section to access the corresponding MIX/MATRIX channel, and then
press the appropriate [CUE] key in the Centralogic section.
MIX buses can be either a FIXED type whose send level is fixed, or a VARI type whose send
level is variable. The MATRIX buses are all VARI type. You can switch between FIXED and
VARI types for each two adjacent odd/even-numbered MIX buses. To do so, press the SETUP
button and then the BUS SETUP button to open the BUS SETUP window.
If the MIX bus is a FIXED type
A gray circle is displayed instead of the TO MIX SEND LEVEL knob, and you cannot
adjust the send level.
For a VARI type MIX bus or a MATRIX bus
The TO MIX SEND LEVEL knob is displayed in the same color as the corresponding knob
in the SELECTED CHANNEL section. In this case, you can use the corresponding knob in
the SELECTED CHANNEL section to adjust the send level.
If the MIX/MATRIX bus is a stereo bus
You can link the main parameters of two adjacent odd/even-numbered MIX/MATRIX
buses. If the send-destination MIX/MATRIX bus is assigned as stereo, the left knob of the
two adjacent TO MIX/MATRIX SEND LEVEL knobs will operate as the TO MIX/MATRIX
PAN knob. (If BALANCE mode is selected in the TO STEREO/MONO window, it will
operate as a BALANCE knob).
NOTE
For a MONO channel, the right knob will adjust the common send level to the two MIX/MATRIX
buses, and the left knob will adjust the panning between the two MIX/MATRIX buses. Rotating
the left TO MIX/MATRIX SEND LEVEL knob counter-clockwise will increase the amount of signal
sent to the odd-numbered MIX/MATRIX bus, and rotating it clockwise will increase the amount
sent to the even-numbered MIX/MATRIX bus.
For a STEREO channel, if BALANCE mode has been selected on the TO STEREO/MONO
window, the right knob adjusts the common send level for the two MIX/MATRIX buses, and the
left knob adjusts the volume balance of the left and right signals sent to the two MIX/MATRIX
buses. Rotating the left TO MIX/MATRIX SEND LEVEL knob counter-clockwise will increase the
amount of signal sent from the L-channel to the odd-numbered MIX/MATRIX bus, and rotating it
clockwise will increase the amount sent from the R-channel to the even-numbered MIX/MATRIX
bus. If PAN mode has been selected in the TO STEREO/MONO window, the left knob will function
as the PAN knob. The right knob function will be the same as in BALANCE mode.
STEP
1. Assign an output port to each MIX/MATRIX bus to which you want to send signals,
and connect your monitor system, external effects processor, or other device to the
corresponding output port.
2. Use the [SEL] keys on the top panel to select the input channel that will send signals
to the MIX/MATRIX bus.
3. Press one of the knobs in the Selected Channel section.
4. Turn on the ON button in the SEND field in the SELECTED CHANNEL VIEW screen.
5. Turn on the TO MIX/MATRIX SEND ON/OFF button for the send-destination MIX
bus.
6. Use the MIX/MATRIX SEND LEVEL knob in the SELECTED CHANNEL section to adjust
the send levels to the MIX/MATRIX buses.
SELECTED CHANNEL
VIEW screen
Input channels
V5 Reference Manual
45
Using the Centralogic section
You can use the multifunction knobs in the Centralogic section to adjust the send level of
signals sent from eight consecutive input channels to a specific MIX/MATRIX bus.
NOTE
If you want to monitor a signal being sent to a specific MIX/MATRIX bus, use the Bank Select
keys to assign the corresponding MIX channel to the Centralogic section, and then press the
[CUE] key for that MIX/MATRIX channel.
In the OVERVIEW screen, you can also adjust the send level of the signal sent to the MIX/
MATRIX buses. To do so, press the SEND LEVEL knob for the MIX/MATRIX that you want to
adjust, and then use the multifunction knob in the Centralogic section to adjust it.
MIX SEND/MATRIX SEND window
1 ALL PRE button
Sets the send point to PRE. (The send point is the point at which signals are sent from
all send-source channels - including the input and output channels - to the selected send
destination.) At this time, the PRE/POST button will light.
2 ALL POST button
Sets the send point to POST. (The send point is the point at which signals are sent from
all send-source channels - including the input and output channels - to the selected send
destination.) At this time, the PRE/POST button will turn off.
3 Send destination indicator
Indicates the currently-selected send destination.
4 Send destination select buttons
Select MIX/MATRIX buses as the send destination.
5 Channel select button
Selects the send-source channel that you wish to control. The current channel icon,
number, and color appear on the button, and the channel name appears below the
button.
6 PRE/POST button
Switches the send point of each send-source channel between PRE and POST. If the
button is lit, the send point is set to PRE.
NOTE
If the PRE/POST button is on, you can also select PRE EQ (immediately before the EQ) or PRE
FADER (immediately before the fader) for each MIX/MATRIX bus. This setting is made in the BUS
SETUP window (page 252).
The PRE/POST button is not displayed for FIXED type MIX buses.
7 SEND ON/OFF button
Switches the send of each send-source channel on or off.
STEP
1. Assign an output port to each MIX/MATRIX bus to which you want to send signals,
and connect your monitor system, external effects, or other device to the
corresponding output port.
2. Use the Bank Select keys in the Centralogic section to select the channels that you
want to control.
3. In the OVERVIEW scree, press the TO MIX/MATRIX SEND LEVEL knob to select the
desired send-destination MIX/MATRIX bus, and then press it again.
4. Use the SEND ON/OFF button in the MIX SEND/MATRIX SEND screen to turn the
signal on/off and to adjust the send level.
OVERVIEW screen
13 32 1 2
9
7
6
5
4
9
8 8
7
6
5
4
Input channels
V5 Reference Manual
46
8 SEND PAN/BALANCE knob
Sets the panning or balance of signals sent to the stereo send destination. If the send
destination is monaural or set to FIXED, this knob will not appear.
If the send source is monaural, this knob functions as a PAN knob.
If the send source is stereo, you can use PAN/BALANCE mode setting
in the TO STEREO/MONO window to select whether PAN/BALANCE
will function as a PAN or BALANCE knob. The knob for the mode
selected here will appear.
9 SEND LEVEL knob
Indicates the level of signals sent to the selected send destination. Press this knob to
control the level using the multifunction knobs.
If the send destination is set to FIXED, only a gray circle will appear.
Using the faders (SENDS ON FADER mode)
You can use the faders on the top panel to adjust signals that are sent from all input channels
to a specific MIX/MATRIX bus.
NOTE
Press the SENDS ON FADER button to switch to SENDS ON FADER mode. The most recently
selected group of MIX/MATRIX buses will be assigned to the Centralogic section. The faders in
the Channel Strip section and Master section will move to indicate the send level of signals that
are routed from each channel to the currently-selected MIX/MATRIX bus.
Alternatively, you can press a SEND LEVEL knob in the SELECTED CHANNEL section to
display a window from which you can select the send-destination MIX/MATRIX bus.
You can also select a MIX/MATRIX bus by using the Bank Select keys and the [SEL] keys in the
Centralogic section. If you select the MIX buses or MATRIX buses by pressing the [SEL] keys,
the setting of the MIX/MTRX ON FADER switch button will be changed automatically.
If you press the currently-selected MIX/MATRIX bus select button again, cue monitoring will be
turned on for the related MIX/MATRIX channel. This method is convenient if you want to monitor
the signal that is being sent to the selected MIX/MATRIX bus.
You can assign the SENDS ON FADER function to a USER DEFINED key. This lets you quickly
switch to SENDS ON FADER mode for a specific MIX/MATRIX bus, and quickly switch back
again.
STEP
1. Assign an output port to each MIX/MATRIX bus to which you want to send signals,
and connect your monitor system, external effects, or other device to the
corresponding output port.
2. In the Function Access Area, press the SENDS ON FADER button.
3. Use the MIX/MTRX ON select buttons in the Function Access Area to switch between
MIX 1-16 and MIX 17-24/MATRIX.
4. Use the MIX/MATRIX bus selection buttons in the Function Access Area to select the
send-destination MIX/MATRIX bus.
5. Use the faders in the Channel Strip section on the top panel to adjust the send level
of signals routed from the input channels to the selected MIX/MATRIX bus.
Function
access area
Input channels
V5 Reference Manual
47
SENDS ON FADER mode
1 MIX/MTRX ON FADER switch button
Use this button to switch between MIX 1-16 and MIX 17-24/MATRIX for the bus
displayed in the Function Access Area.
2 MIX/MATRIX bus select buttons
Select the buses that will be controlled by the faders.
3 Close button
Closes the SENDS ON FADER mode.
Channel name display indication
In SENDS ON FADER mode, ON/OFF is indicated for the channel.
On the PREFERENCE page in the USER SETUP pop-up window, the channel number is
shown if NAME DISPLAY is set to “NAME ONLY”.
3
2
1
CHANNEL ON
CHANNEL OFF
Channel number
display
Input channels
V5 Reference Manual
48
Correcting delay between channels (Input Delay)
This section explains how to correct delay between input channels by using the Input Delay
function.
This function is useful when you want to correct the phase variance caused by microphone
locations on the stage, to add depth to the sound by using phase variance, or to correct a
delay (a time gap) that may exist between video and audio that are sent from a site for
broadcast on TV.
NOTE
If you are viewing the 8 ch INPUT DELAY screen, you can use the Bank Select keys in the
Centralogic section to switch the channels being controlled in groups of eight.
INPUT DELAY screen (8ch)
You can set the on/off status and the value of the input channel delay.
1 DELAY SCALE button
Press the button to display the DELAY SCALE window, in which you can select the unit
for the delay time.
There are five delay scales: meter (meter/sec), feet (feet/sec), sample (number of
samples), ms (milliseconds), and frame (frames). If you select frame as the units, you can
choose from six frame rates: 30, 30D, 29.97, 29.97D, 25, and 24. In this case, fr will
appear as the units in the channel name display.
2 Channel select button
The currently-selected input channel is indicated in blue. Press the button to select the
channel.
3 Delay setting knob (input channels only)
You can use the multifunction knob to adjust the delay. You can view the current value
immediately above the knob (always shown in unit of ms) and below the knob (shown
using the currently-selected scale). If ms (millisecond) has been selected for the DELAY
SCALE, nothing will appear above the knob.
4 Tabs
Enable you to switch between windows.
5 Close button
Closes the screen.
STEP
1. Use the [SEL] keys on the top panel to select the input channel that will send signals
to the MIX/MATRIX bus.
2. Press one of the knobs in the Selected Channel section.
3. Press the INPUT DELAY field in the SELECTED CHANNEL VIEW screen.
4. Press the 8 ch tab in the INPUT DELAY screen.
5. Use the on-screen buttons and the multifunction knobs to set the delay.
SELECTED CHANNEL
VIEW screen
INPUT DELAY screen
1 5
2
3
4
Input channels
V5 Reference Manual
49
INPUT DELAY (CH 1-48, CH 49-72/ST IN (CL5),
CH 49-64/ST IN (CL3), ST IN (CL1))
1 DELAY SCALE button
Press the button to display the DELAY SCALE window, in which you can select the unit
for the delay time.
2 Channel select button
Lights to indicate the currently-selected input channel. Press the button to select the
channel.
3 Delay setting knob (input channels only)
Press this knob to adjust the value using the multifunction knob. You can view the
current value immediately above the knob (always shown in unit of ms) and below the
knob (shown using the currently-selected scale).
NOTE
If ms (millisecond) has been selected for the DELAY SCALE, nothing will appear to the right of
the knob.
Additional functions for stereo input channels
With V3, you can temporarily set the signals sent to a stereo input channel as mono. You can
select from the following three settings.
L-MONO
Only the L channel is temporarily set as a mono signal.
R-MONO
Only the R channel is temporarily set as a mono signal.
1
2
3
STEREO IN Lch
STEREO IN Rch
STEREO R
STEREO L
ON
ON
PAN/BAL
PAN/BAL
STEREO IN Lch
STEREO IN Rch
STEREO R
STEREO L
ON
ON
PAN/BAL
PAN/BAL
Input channels
V5 Reference Manual
50
LR-MONO
Although the result is a monaural signal that is the summation of signals from both channels,
the R channel of the stereo input channel is muted.
NOTE
When you set LR-MONO, the PAN mode is selected at the same time. In addition, the PAN knob
is set to the center position.
When you set LR, L-MONO, or R-MONO, the BALANCE mode is selected at the same time. In
addition, the BALANCE knob is set to the center position.
Setting procedure
If a stereo input channel is selected, the SELECTED CHANNEL VIEW screen will appear as
shown below.
1 LR-MONO SELECT field
Select one of the four buttons. The button you select lights up, and the others go off.
If a stereo input channel is selected, the OVERVIEW screen will appear as shown below.
2 LR-MONO SELECT button
This a toggle button. The setting switches each time the button is pressed.
1
Normal STEREO setting
L-MONO
R-MONO
LR-MONO
2
Input channels
V5 Reference Manual
51
Surround output for input channels
Setting Surround mode
You can enable surround mixes by changing bus settings to Surround mode.
NOTE
When you switch from Stereo mode to Surround mode, the signals for MIX1/2, 3/4, and 5/6
change to MONO x2.
However, when you switch from Surround mode to Stereo mode, the signals for MIX1/2, 3/4, and
5/6 remain as MONO x2.
SELECTED CHANNEL VIEW screen
If you set a bus to Surround mode in BUS SETUP, the SELECTED CHANNEL VIEW screen
appears as shown below.
1 L/R knob
This parameter is used to set the left/right surround position.
Use the SEND knob (MIX 1) of the Selected Channel section to make adjustments.
2 F/R knob
This parameter is used to set the front/rear surround position.
Use the SEND knob (MIX 3) of the Selected Channel section to make adjustments.
3 Assign buttons for each bus
If there is a bus from which you do not want to output an audio signal, turn that button
off.
4 DIV knob
This determines how the Center signal is fed to the Left, Right, and Center channels.
When set to 0, the Center signal is fed only to the Left and Right channels. When set to
50, the Center signal is fed equally to the Left, Right, and Center channels. When set to
100, it’s fed to only the Center channel (i.e., Real Center).
Use the SEND knob (MIX 5) of the Selected Channel section to make adjustments.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the SURROUND SETUP button (page 214).
3. Press the 5.1 SURROUND button.
4. Assign channels to MIX 1 - 6 for surround output.
5. Press the APPLY button.
6. Press the OK button in the confirmation dialog box.
SETUP screen
SURROUND SETUP screen
1
2
4
5
7
3
3
6
Input channels
V5 Reference Manual
52
5 LFE knob
This sets the level of the LFE (Low Frequency Effects) Channel.
Use the SEND knob (MIX 6) of the Selected Channel section to make adjustments.
6 Surround position
The color of the ball shown here changes depending on whether the surround position
is a hard pan (panned fully left or right) or any other setting.
Hard pan: Red
Any other setting: Orange
7 Surround graph
This graph shows the surround positions. Press here to open the SURROUND PAN 1CH
screen.
OVERVIEW screen
If you set a bus to Surround mode in BUS SETUP, the OVERVIEW screen appears as shown
below.
1 Surround graph
This graph shows the surround positions. Press here to open the SURROUND PAN 1CH
screen.
2 L/R F/R switch button
Use this toggle button to switch between the screen for adjusting L/R and the screen for
adjusting F/R.
Use the SEND knob (MIX 5) of the Selected Channel section to make adjustments.
3 LFE knob
This sets the level of the LFE (Low Frequency Effects) Channel.
Use the SEND knob (MIX 6) of the Selected Channel section to make adjustments.
3
2
1
Adjusting L/R
3
2
1
Adjusting F/R
Input channels
V5 Reference Manual
53
SURROUND PAN 1CH screen
If you set a bus to Surround mode in BUS SETUP, the SURROUND PAN 1CH screen appears
as shown below. This screen is displayed when you press the pan display area in the
SELECTED CHANNEL VIEW screen or the OVERVIEW screen.
1 Surround graph
This graph shows the surround positions.
2 Surround position
You can set the surround position by touching and dragging the ball in the graph.
3 Assign buttons for each bus
All of these buttons are turned on by default. If there is a bus from which you do not
want to output an audio signal, turn that button off.
4 L/R knob
This parameter is used to set the left/right surround position.
Use the SEND knob (MIX 1) of the Selected Channel section to make adjustments.
5 F/R knob
This parameter is used to set the front/rear surround position.
Use the SEND knob (MIX 3) of the Selected Channel section to make adjustments.
6 DIV knob
This determines how the Center signal is fed to the Left, Right, and Center channels.
When set to 0, the Center signal is fed only to the Left and Right channels. When set to
50, the Center signal is fed equally to the Left, Right, and Center channels. When set to
100, it’s fed to only the Center channel (i.e., Real Center).
Use the SEND knob (MIX 5) of the Selected Channel section to make adjustments.
7 LFE knob
This sets the level of the LFE (Low Frequency Effects) Channel.
Use the SEND knob (MIX 6) of the Selected Channel section to make adjustments.
8 DEFAULT button
Press this button to reset all parameters to the initial values.
9 COPY button
All parameter settings will be copied in buffer memory.
0 PASTE button
Press this button to paste the copied settings from buffer memory to the current
settings. If no valid data has been copied in the buffer memory, nothing will happen.
>9
1
38
6 754
3
2
Input channels
V5 Reference Manual
54
SURROUND PAN screen (CH 1-48, CH 49-72/ST IN (CL5), CH 49-
64/ST IN (CL3), ST IN (CL1))
If you set a bus to Surround mode in BUS SETUP, the SURROUND PAN screen (CH 1-48,
CH 49-72/ST IN (CL5), CH 49-64/ST IN (CL3), ST IN (CL1)) appears as shown below. This
screen is displayed when you press the pan display area in the SELECTED CHANNEL VIEW
screen or the OVERVIEW screen.
1 Surround graph
This graph shows the surround positions.
2 L/R F/R switch button
Use this toggle button to switch between the screen for adjusting L/R and the screen for
adjusting F/R.
Use the SEND knob (MIX 5) of the Selected Channel section to make adjustments.
1
2
Adjusting L/R
Adjusting F/R
1
2
Input channels
V5 Reference Manual
55
TO STEREO/MONO screen
If you set a bus to Surround mode in BUS SETUP, the TO STEREO/MONO 8CH screen for
MIX 1-8 appears as shown below. MIX 1-6 are for setting downmixes.
1 L/R buttons
Use these buttons to set the output destination.
2 Coefficient Setting fader
Use this fader to set the downmix coefficient. There is a ∑ clip indicator.
The TO STEREO/MONO OUTPUT screen appears as shown below. Parameters cannot be
set for MIX 1 - 6; this screen is only for displaying parameters.
Channel library operations
The “INPUT CHANNEL LIBRARY” enables you to store and recall various parameters
(including the head amp settings) for input channels.
To recall a library item, press the corresponding LIBRARY button in the SELECTED
CHANNEL VIEW screen. For details on using the library, refer to the “Using libraries” section
in the separate Owner’s Manual.
2
1
LIBRARY button
OUTPUT channels
V5 Reference Manual
56
OUTPUT channels
This chapter explains output channels (MIX channels, MATRIX channels, STEREO channels,
MONO channels).
Signal flow for output channels
The output channel section takes the signals sent from the input channels to the various
buses, processes them with EQ and dynamics, and sends them to output ports or other
buses. The following types of output channels are provided.
MIX channels
These channels process signals sent from input channels to MIX buses, and output them to
the corresponding output port, MATRIX bus, STEREO bus, or MONO (C) bus.
STEREO channel/MONO (C) channel
Each of these channels process the signal sent from the input channels to the STEREO bus
or MONO (C) bus, and send it to the corresponding output port or MATRIX bus. If input
channels are in LCR mode, the STEREO (L/R) channels and the MONO (C) channel can be
used together as a set of three output channels.
MATRIX channel
These channels process the signals sent from input channels, MIX channels, and STEREO/
MONO channels to MATRIX buses, and send them to the corresponding output ports.
4 BAND EQ (4 band equalizer)
A parametric EQ with four bands: HIGH, HIGH MID, LOW MID, and LOW.
DYNAMICS 1
This is a dynamics processor that can be used as a compressor, expander, or compander.
•LEVEL
Adjusts the output level of the channel.
MIX
12 23
24
ST
LR
M
O
N
O
(C)
12 78
LR
TRIM
CUE B ON
CUE(A) ON
KEY IN
MATRIX
(USE 7-8
AS CUE B)
CUE (A)
MIX
12 23
24
ST
LR
M
O
N
O
(C)
MATRIX
(USE 7-8
AS CUE B)
12 78
CUE (A)
LR
TRIM
CUE B ON
CUE(A) ON
MIX
12 23
24
ST
LR
M
O
N
O
(C)
MATRIX
(USE 7-8
AS CUE B)
12 78
CUE (A)
LR
MATRIX 1-6,7-8(CUE B L,R)
OUT 1-6,7-8(CUE B L,R)
IN 1-6,7-8(CUE B L,R)
CUE(A) ON 1-6
CUE B ON
TRIM
This section does not exist in MATRIX 7-8.
MATRIX OUT 1-6,7-8(CUE B L,R)
OUTPUT channels
V5 Reference Manual
57
ON (On/off)
Turns the output channel on or off. If this is off, the corresponding channel will be
muted.
MATRIX ON/OFF (MATRIX send on/off)
This is an on/off switch for signals sent from the MIX channels, STEREO (L/R) channel,
or MONO (C) channel to each MATRIX bus.
MATRIX (MATRIX send level)
This adjusts the send level of the signal sent from the MIX channels, STEREO (L/R)
channel, or MONO (C) channel to each MATRIX bus 1 - 8. For the position from which
the signal will be sent to the MATRIX bus, you can choose either immediately before the
fader, or immediately after the [ON] key.
If the send-destination MATRIX bus is set to stereo, you can use the PAN knob to adjust
the panning between the two MATRIX buses. If the send-source is a stereo MIX channel
or the STEREO channel, use the BALANCE knob to adjust the volume balance of the left
and right channels sent to the two MATRIX buses.
•INSERT
You can patch the desired output/input ports to insert an external device such as an
effect processor. You can switch the insert-out and insert-in locations.
METER
Indicates the level of the output channel.
You can switch the position at which the level is detected.
KEY IN (MIX channels 21-24 only)
You can send the output signals of MIX channels 21 - 24 to Dynamics processors and
use them as key-in signals to control the Dynamics.
RACK IN PATCH
Patches the output signal of an output channel to an input of the rack.
OUTPUT PATCH
Assigns an output port to an output channel.
MONITOR SELECT
Selects the output signal of an output channel as a monitor source.
Specifying the channel name/icon
STEP
1. Use the Bank Select keys in the Centralogic section to select the output channels.
2. On the OVERVIEW screen, press the channel number/channel name field of the
channel for which you want to specify a channel name/icon.
3. Follow the steps for the input channels (page 30).
OVERVIEW screen PATCH/NAME screen
OUTPUT channels
V5 Reference Manual
58
Sending signals from MIX channels to the STEREO/
MONO bus
There are two ways to send signals to the STEREO bus or MONO bus: ST/MONO mode and
LCR mode. You can select the mode individually for each channel. Features of each mode
are the same as for input channels.
NOTE
Refer to “Signal level when LCR mode is selected” (page 42) for details on how the signal level
sent from an LCR mode MIX channel to each bus will change according to the operation of the
TO ST PAN knob.
TO STEREO/MONO window(8ch)
You can control the on/off and pan/balance settings of the signal sent from MIX channels to
the STEREO (L/R) bus and MONO (C) bus, in groups of eight channels.
1 Channel select button
Selects the channel. You can select multiple channels simultaneously.
2 Mode LEDs
The LED of the currently-selected mode will light.
STEP
1. Use the Bank Select keys in the Centralogic section to select the MIX channel from
which you want to send the signal to the STEREO/MONO bus.
2. In the STEREO/MONO field, press a knob to select the channel you want to adjust in
the OVERVIEW screen, and then press the knob once again.
3. Use the MODE select button in the TO STEREO/MONO window to select either ST/
MONO mode or LCR mode for each channel.
4. In the MASTER section on the top panel, turn on the [ON] key for the STEREO
channel/MONO channel, and then raise the fader to an appropriate level.
5. In the Centralogic section, press an OUTPUT bank select key so that the MIX
channels you want to control are assigned to the Centralogic section.
6. Turn on the [ON] keys for those channels, and use the fader in the Centralogic
section to raise the master level of the MIX channel to an appropriate position.
The subsequent steps will differ depending on whether ST/MONO mode or LCR mode was
selected for the channel in step 3.
Channels for which ST/MONO mode is selected
7. In the TO STEREO/MONO window, use the ST/MONO button to turn a signal sent
from the MIX channel to the STEREO bus/MONO bus on or off.
8. Use the TO ST PAN knob to set the panning of the signal sent from the MIX channel
to the STEREO bus.
Channels for which LCR mode is selected
7. Turn on the LCR button in the TO STEREO/MONO window.
8. Press the CSR knob to select it, and use multifunction knobs 1 - 8 to adjust the level
difference between signals sent from that channel to the STEREO (L/R) bus and to
the MONO (C) bus.
9. Press the TO ST PAN knob to select it, and use multifunction knobs 1 - 8 to adjust
the panning of signals sent from the MIX channel to the STEREO (L/R) bus and
MONO (C) bus, and the level balance of signals sent to the MONO (C) bus and
STEREO (L/R) bus.
OVERVIEW screen TO STEREO/MONO window
1
8
9
2
3
6
5
4
7
ST/MONO mode LCR mode
OUTPUT channels
V5 Reference Manual
59
3 MODE select button
Press this button repeatedly to toggle between ST/MONO and LCR.
4 ST/MONO buttons
These buttons are individual on/off switches for signals that are sent from each channel
to the STEREO bus/MONO bus when the MONO button is set to ST/MONO mode.
5 Σ clipping indicator
Lights to indicate a signal is clipping at some point in the channel.
6 TO ST PAN/TO ST BALANCE knob
If the type of the MIX channel signal is MONO, this knob will function as a PAN knob
that adjusts the left and right pan position of the signal sent to the STEREO bus. If the
type of MIX channel signal is STEREO, this knob will function as a BALANCE knob that
adjusts the volume level balance of left and right signals sent to the STEREO bus. To
adjust the value, press the knob to select it, and then operate the corresponding
multifunction knob.
7 Tabs
Enable you to switch between windows.
8 LCR button
This button is an overall on/off button for signals sent from a channel to the STEREO bus
and MONO bus. If this button is off, no signals will be sent from the corresponding input
channel to the STEREO bus or MONO bus.
9 CSR knob
Adjusts the relative level of signals sent from the channel to the STEREO (L/R) bus and
to the MONO (C) bus, in the range of 0 - 100%. To adjust the value, press the knob to
select it, and then operate the corresponding multifunction knob.
TO STEREO/MONO screen
(CH 1-48, CH 49-72/ST IN (CL5), CH 49-64/ST IN (CL3),
ST IN (CL1), OUTPUT)
Adjusts the status of a signal sent from the corresponding channel to the STEREO/MONO
bus. Here you can also adjust the pan or balance in groups of the selected eight channels.
1 Channel select button
Selects the channel. You can select multiple channels simultaneously.
2 Σ clipping indicator
Lights to indicate a signal is clipping at some point in the channel.
3 TO ST PAN/TO ST BALANCE knob
Adjusts the panning or balance.
To adjust the value, press the knob to select it, and then operate the corresponding
multifunction knob.
If the signal level reaches the overload point at any meter detection point in that
channel, the Σ clipping indicator to the right of the knob will light.
4 ST/MONO indicator
If a channel is set to ST/MONO mode, these indicators will individually indicate the on/
off status of signals sent from the channel to the STEREO bus/MONO bus.
If that channel is set to LCR mode, the LCR indicator will be displayed in this location.
The LCR indicator indicates the on/off status of all signals sent from that channel to the
STEREO bus/MONO bus.
1
2
3
4
OUTPUT channels
V5 Reference Manual
60
Sending signals from MIX channels and STEREO/
MONO channels to MATRIX buses
You can send a signal from a MIX or STEREO/MONO channel to MATRIX buses 1 - 8 in the
following two ways.
Using the Selected Channel section
With this method, you use the knobs in the SELECTED CHANNEL section to adjust the send
levels to the MATRIX buses. This method allows you to simultaneously control signals sent
from a specific MIX, STEREO (L/R), or MONO (C) channel to all MATRIX buses.
Using the Centralogic section
With this method, you use the multifunction knobs in the Centralogic section to adjust the
send levels to the MATRIX buses. This method allows you to simultaneously control signals
sent from up to eight MIX, STEREO (L/R), or MONO (C) channels to a specific MATRIX bus.
Using the Selected Channel section
Use the knobs in the SELECTED CHANNEL section to adjust the send level of signals sent
from the desired MIX, STEREO (L/R) or MONO (C) channel to all MATRIX buses.
NOTE
You can also use the [SEL] key in the MASTER section to directly select the STEREO/MONO
channels.
If you want to monitor the signal being sent to a specific MATRIX bus, use the Bank Select keys
in the Centralogic section to access the corresponding MIX/MATRIX channel, and then press the
appropriate [CUE] key in the Centralogic section.
STEP
1. Assign an output port to the MATRIX bus to which you want to send signals, and
connect an external device.
2. Using the Bank Select keys in the Centralogic section, assign the desired MIX
channels or the STEREO/MONO channels to the Centralogic section.
3. Use the [SEL] keys of the Centralogic section to select the input channel that will
send signals to the MATRIX buses.
4. Press one of the knobs in the Selected Channel section.
5. In the SELECTED CHANNEL VIEW screen, turn on the TO MATRIX SEND ON/OFF
button for the send-destination MATRIX bus.
6. Use the MIX/MATRIX SEND LEVEL knob in the SELECTED CHANNEL section to adjust
the send levels to the MATRIX buses.
SELECTED CHANNEL VIEW
screen
OUTPUT channels
V5 Reference Manual
61
Using the Centralogic section
This method lets you use the multifunction knobs (in the Centralogic section) to
simultaneously adjust the send levels from the eight channels selected in the Centralogic
section to the desired MATRIX bus.
NOTE
If you want to monitor signals being sent to a specific MATRIX bus, use the Bank Select keys to
access the corresponding MATRIX channel in the Centralogic section, and then press the [CUE]
key for that MATRIX channel.
If you again press the currently-selected MATRIX bus select button, cue monitoring will be turned
on for the related MATRIX channel. This method is convenient if you want to monitor a signal that
is being sent to the selected MATRIX bus.
In the OVERVIEW screen, you can also adjust the send level of the signal sent to the MIX/
MATRIX buses. To do so, press the SEND LEVEL knob for the TO MIX/MATRIX that you want to
adjust, and then use the multifunction knob in the Centralogic section to adjust it.
MATRIX SEND screen
1 ALL PRE button
Sets the send point to PRE. (The send point is the point at which signals are sent from
all send-source channels - including the input and output channels - to the selected send
destination.)
2 ALL POST button
Sets the send point to POST. (The send point is the point at which signals are sent from
all send-source channels - including the input and output channels - to the selected send
destination.)
3 Send destination indicator
Indicates the currently-selected send destination.
4 Send destination select buttons
Select MIX/MATRIX buses as the send destination.
5 Channel select button
Selects the send-source channel that you wish to control. The current channel icon,
number, and color appear on the button, and the channel name appears below the
button.
6 PRE/POST button
Switches the send point of each send-source channel between PRE and POST. If the
button is lit, the send point is set to PRE.
7 SEND ON/OFF button
Switches the send of each send-source channel on or off.
STEP
1. Assign an output port to the MATRIX bus to which you want to send signals, and
connect an external device to that output port.
2. Use the Bank Select keys in the Centralogic section to select the channels that you
want to control.
3. In the OVERVIEW screen, press the TO MATRIX SEND LEVEL knob to select the
desired send-destination MATRIX bus, and then press it again.
4. Set the SEND ON/OFF button to ON, and use the SEND LEVEL knob to adjust the
send level.
OVERVIEW screen
13 2
9
8
7
6
5
4
OUTPUT channels
V5 Reference Manual
62
8 SEND PAN/BALANCE knob
Sets the panning or balance of signals sent to the stereo send destination. If the send
destination is monaural or set to FIXED, this knob will not appear.
If the send source is monaural, this knob functions as a PAN knob.
If the send destination is stereo, this is fixed to BALANCE.
9 SEND LEVEL knob
Indicates the level of signals sent to the selected send destination. Press this knob to
control the level using the multifunction knobs.
Using the faders (SENDS ON FADER mode)
You can use the faders on the top panel to adjust signals that are sent from the MIX and
STEREO/MONO channels to a specific MATRIX bus.
NOTE
Alternatively, press a SEND LEVEL knob in the SELECTED CHANNEL section to display a
popup window, from which you can select a MIX/MATRIX bus.
You can also select a MIX/MATRIX bus by using the Bank Select keys and the [SEL] keys in the
Centralogic section. If you switch buses by pressing the [SEL] keys, the setting of the MIX 1-16
and MIX 17-24/MATRIX ON FADER switch buttons will also change automatically.
If you press the currently-selected MIX/MATRIX bus select button again, cue monitoring will be
turned on for the related MIX/MATRIX channel. This method is convenient if you want to monitor
the signal that is being sent to the selected MIX/MATRIX bus.
You can assign the SENDS ON FADER function to a USER DEFINED key. This lets you quickly
switch to SENDS ON FADER mode for a specific MIX/MATRIX bus, and quickly switch back
again.
STEP
1.
Make sure that an output port is assigned to the MATRIX bus to which you want to send
signals, and that your monitor system etc. is connected to the corresponding output
port.
2. In the Function Access Area, press the SENDS ON FADER button.
The CL series unit will switch to SENDS ON FADER mode. The faders in the Channel Strip
section and Master section will move to the send levels of the signals that are routed from
each channel to the currently-selected MIX/MATRIX bus. The [ON] keys will also change
to the SEND ON status.
In SENDS ON FADER mode, the Function Access Area in the display will show the buttons
that enable you to switch between MIX 1-16 ON FADER mode and MIX 17-24/MATRIX
ON FADER mode, and the buttons that enable you to select the destination MIX/MATRIX
buses.
3.
Use the MIX 1-16 and MIX 17-24/MATRIX select buttons to switch between MIX 1-16 and
MIX 17-24/MATRIX
.
Now you can use the MIX/MATRIX bus select buttons to specify the destination MIX/
MATRIX buses.
4.
Use the MIX/MATRIX bus selection buttons in the Function Access Area to select the
send-destination MATRIX bus.
5. Use the faders in the top panel Centralogic section to adjust the send level from the MIX
and STEREO/MONO channels to the selected MATRIX bus.
6. Repeat steps 4 - 5 to adjust the send level for other MATRIX buses in the same way.
7. When you’re finished adjusting the MATRIX send levels, press the X symbol in the
Function Access Area.
The Function Access Area display will return to its prior state, and the CL console will exit
SENDS ON FADER mode and return to normal mode.
Function
Access Area
OUTPUT channels
V5 Reference Manual
63
Correcting delay between channels (Output Delay)
This Output Delay function is useful when you want to correct the timing of output signals sent
to speakers that are located at a distance from each other.
OUTPUT PORT screen
1 Slot number/Card type
If an output channel of slot 1 - 3 is selected for operations, this shows the slot number
and the type of I/O card installed in that slot.
2 DELAY SCALE button
Press this button to open the DELAY SCALE window, in which you can select the unit for
the delay time.
3 Output Port
This is the type and number of the output port to which the channel is assigned.
4 Channel select button
Enables you to select the channel that you want to assign to the output port. The name
of the currently-selected channel is displayed.
5 Delay time knob
Sets the delay time of the output port. Press this knob to select it, and then use
multifunction knobs 1 - 8 to adjust the settings. The millisecond delay time value is
indicated above the knob, and the delay time value in the units selected in the DELAY
SCALE window is indicated below the knob.
NOTE
If the scale is set to ms, the delay time value is not shown above the knob.
STEP
1. In the Function Access Area, press the SETUP button.
2.
Press the OUTPUT PORT button in the SYSTEM SETUP field located in the center of the
SETUP screen.
3. Specifies the delay time, and turns on the DELAY button.
SETUP screen OUTPUT PORT screen
2
1
3
4
5
6
7
8
9
0
OUTPUT channels
V5 Reference Manual
64
6 DELAY button
Switches the output port delay on or off.
7 Ø (Phase) button
Switches the phase of the signal assigned to the output port between normal phase
(black) and reverse phase (yellow).
8 GAIN knob
Adjusts the output gain of the output port. To adjust this value, press the knob in the
screen to select it, and then operate multifunction knobs 1 - 8. Rotate the knob to set
the value in 1.0 dB steps. Rotate the knob while pressing and holding it down to set the
value in 0.1 dB steps. The current value appears immediately below the knob.
9 Level meter
Indicates the level of the signal assigned to the output port.
0 Tabs
Switch the output ports controlled in groups of up to eight ports. Tabs are categorized
into three groups: DANTE, SLOT, and PATCH VIEW. To display tabs in the desired group,
press the group name button located at the right or left end of the bottom row.
Channel library operations
The “OUTPUT CHANNEL LIBRARY” enables you to
store and recall various parameters for output channels.
To recall a library item, select an output channel and
press the LIBRARY button on the SELECTED
CHANNEL VIEW screen.
For details on using the library, refer to the “Using the
library” section in the separate Owner’s Manual.
PHONES OUT LR
[PHONES]
DA
PHONES LEVE L
2
Tip
Ring
Sl ee ve
SLOT1
SLOT2
SLOT3
[SLOT]
16
16
16
ME TER
SLOT1OU T
ME TER
SLOT2OU T
ME TER
SLOT3OU T
DELAY
(MAX:1000ms)
DELAY
(MAX:1000ms)
DELAY
(MAX:1000ms)
DA
[OMNI OUT] (1-8)
8
+
-
1
2
3
ME TER
OMNI OUT
DELAY
(MAX:1000ms)
TRIM
GAIN
OUTPUT
PATCH
2
DIT
[DIGITAL OUT]
AE S/EB U
DELAY
(MAX:1000ms)
ME TER
DIGITAL
OUT
TRIMGAIN
TRIMGAIN
[DANTE OUT] (1-64)
64
ME TER
DANTE OUT
DELAY
(MAX:1000ms)
GAIN
OUTPUT
PATCH
DANT E
OUTPUT
MIX CASCADE OUT 1-24
STEREO CASCADE OUT L,R,MONO(C)
MATRIX CASCADE OU T 1-6,7-8
(CUE B L,R)
CUE(A) CASCADE OUT L,R
DIRECT OUT 1-72{64,48}
MATRIX OUT 1-6,7-8
(CUE B L,R)
MIX OUT 1-24
STEREO OUT L,R,MONO(C)
MONI TOR OUT L,R,MONO(C)
CUE(A) OUT L,R
CH INSERT 1,2 OUT 1-72{64,48}
MIX INSERT OUT 1-24
STEREO INSERT OUT L,R,MONO(C)
MATRIX INSERT OUT 1-6,7-8(CUE B L,R)
2
RECORDER CUE
USB
GAIN
ME TER
RECORDER IN
OUTPUT
PATCH
ENCODER
[2TR RECORDER]
OUTPUT
PATCH
STEREO L
MONO(C)
STEREO R
SURR OUND MONITOR1-6
MONI TOR MAT RIX OUT1-6
OMNI OUT
OUTPUT
PATCH
LIBRARY button
EQ and Dynamics
V5 Reference Manual
65
EQ and Dynamics
Each input channel and output channel on a CL series console provides a four-band EQ and
dynamics.
EQ can be used on all input channels and all output channels. An attenuator is provided
immediately before the EQ, allowing you to attenuate the level of the input signal so that the
GAIN setting for EQ will not cause the signal to clip. Input channels also provide a high-pass
filter that is independent of the EQ.
Input channels provide two dynamics processors: Dynamics 1 can be used as a gate, ducking
device, compressor, or expander, while Dynamics 2 can be used as a compressor, hard
compander, soft compander, or de-esser. Output channels provide one dynamics processor,
which can be used as a compressor, expander, hard compander, or soft compander.
Using EQ
This section explains the four-band EQ that is provided on input channels and output
channels.
NOTE
The EQ field in the OVERVIEW screen shows the response of the EQ. In this OVERVIEW screen,
you can edit the parameter settings by using the EQ knobs in the SELECTED CHANNEL section.
EQ settings can be saved and recalled at any time using the dedicated library. You can also take
advantage of a wide variety of presets suitable for various instruments or situations.
You can also access the SELECTED CHANNEL VIEW screen, and use the knobs in the
SELECTED CHANNEL section to edit the EQ and high-pass filter (page 9).
Even when the HPF/EQ window is displayed, you can use the knobs in the SELECTED
CHANNEL section to control the EQ.
HPF/EQ window (1ch)
This lets you edit all EQ parameters of the currently-selected channel. This is convenient if
you want to make detailed EQ settings for a specific channel.
1 Channel icon/Channel number/Channel name
This area indicates the icon, number and name of the currently-selected channel.
2 LOW SHELVING ON/OFF button
Turn on this button to select the shelving-type filter for the LOW band.
3 HPF ON/OFF button (Output channels only)
Turn on this button to switch the LOW band to a high pass filter.
NOTE
Output channels do not feature a high-pass filter that is independent of the EQ. However, you can
turn on the high-pass filter button on the window to use the LOW band EQ as a high-pass filter.
STEP
1. Use the Bank Select keys in the Centralogic section to select the channels that you
want to control.
2. Press the EQ field in the OVERVIEW screen.
3. Press the 1ch tab in the HPF/EQ window.
4. Press the EQ ON button, and adjust the EQ parameters.
OVERVIEW screen HPF/EQ window
98 A B C D E74
1
3
5
I
J
G
F
H
P
O
M
L
N
6
K
2
<
EQ and Dynamics
V5 Reference Manual
66
4 EQ type select button
Switches the EQ type to PRECISE, AGGRESSIVE, SMOOTH, or LEGACY.
The following EQ types can be selected.
When the EQ type is set to PRECISE, you can press in and turn the Q knob for the HIGH
band to switch between PEQ, shelving type, and low-pass filter.
In addition, you can press in and turn the Q knob for the LOW band to switch between
PEQ and high-pass filter.
NOTE
This operation is possible only with the EQ Q knobs in the SELECTED CHANNEL section on the
console’s top panel.
This operation is not possible with the multifunction knobs in the Centralogic section. It is also not
possible with USER DEFINED knobs that have been assigned to the TOUCH AND TURN
function.
HIGH band
When set to PEQ (Q=0.10), press in and turn the Q knob to the right to switch to
shelving type.
When set to PEQ (Q=16.0), press in and turn the Q knob to the left to switch to low-
pass filter.
When set to shelving type (Q=10.0), press in and turn the Q knob to the left to switch
to PEQ.
When set to low-pass filter, press in and turn the Q knob to the right to switch to PEQ.
LOW band
When set to PEQ (Q=0.10), press in and turn the Q knob to the right to switch to
shelving type.
When set to shelving type (Q=10.0), press in and turn the Q knob to the left to switch
to PEQ.
5 ATT knob
Indicates the attenuation value before the signal enters the EQ. You can use a
multifunction knob to adjust this.
6 Tabs
Use these tabs to select a channel that you want to view on the screen.
7 EQ graph
Displays the parameter values for the EQ and filter.
8 RTA button
If you turn this button ON, a graph indicating the frequency analysis for the input signal
after EQ processing is overlaid on the bottom of the EQ frequency graph.
9 HOLD button
Press this button to hold the graph that displays RTA.
0 OFFSET gain knob
If a frequency is at a low level, its analysis results might not appear clearly in a graph.
The addition of offset gain allows better visibility in graphs for such results. You can
adjust this gain from 0dB to +30dB.
A LIBRARY button
Press this button to open the EQ Library window.
B DEFAULT button
Press this button to reset all EQ/filter parameters to the initial values.
C COPY button
All EQ parameter settings will be copied in buffer memory.
D PASTE button
Press this button to paste the setting in buffer memory to the current EQ. If no valid data
has been copied in the buffer memory, nothing will happen.
E COMPARE button
Press this button to swap between the current EQ settings and the data stored in buffer
memory. If no valid data has been copied in the buffer memory, nothing will happen.
NOTE
For details on how to use the A - E buttons, refer to “Using the tool buttons” in the separate
Owner’s Manual.
F EQ FLAT button
Press this button to reset the GAIN parameters of all EQ band to 0 dB.
G HIGH SHELVING ON/OFF button
Turn on this button to select the shelving-type filter for the HIGH band.
H LPF ON/OFF button
Turn on this button to select the low pass filter for the HIGH band.
PRECISE
This EQ type features “precision” and “controllability.” It can be used to
precisely adjust the desired points, to flexibly respond to a variety of music
production needs. The Low/High shelving filters have “Q” parameters that
allow knee adjustments.
AGGRESSIVE
This EQ type features “effective musical” characteristics. It allows you to
create an aggressive tone, making it a very powerful tool for artistic
expression.
SMOOTH
This EQ type focuses on a “smooth sound quality.” It allows you to create
natural sounds without significant modifications to the atmosphere of the
original sound.
LEGACY
This is the standard EQ type found in classic Yamaha digital mixers, such as
the PM1D and the PM5D. On the left side of the EQ graph, you can switch
between TYPE I (an algorithm used in previous Yamaha digital mixers) and
TYPE II (an algorithm that reduces interference between bands).
EQ and Dynamics
V5 Reference Manual
67
I EQ ON/OFF button
Switches the EQ on or off.
J EQ IN/OUT level meters
Indicates the peak level of signals before and after the EQ. For a stereo channel, these
meters indicate the level of both the L and R channels.
K EQ parameter setting knobs
Indicates the Q, FREQUENCY, GAIN parameters and BYPASS button for the LOW, LOW
MID, HIGH MID, and HIGH bands. You can use a multifunction knob to adjust this.
NOTE
If the shelving type has been selected for the LOW band, or if HPF is selected for an output
channel, the LOW band Q parameter will not appear.
If shelving type has been selected for the HIGH band, or if LPF is selected, the HIGH band Q
parameter will not appear.
When the BYPASS button is on, the Q, FREQUENCY, and GAIN knobs for that band turn gray.
L HPF ON/OFF button (input channels only)
Switches the HPF on or off.
NOTE
Input channels provide a high-pass filter that is independent of the four-band EQ. Turn on the
HPF ON/OFF button, and use the HPF FREQUENCY knob to adjust the cutoff frequency.
M HPF FREQUENCY knob (input channels only)
Indicates the cutoff frequency of the HPF. You can use a multifunction knob to adjust
this.
N HPF type select button (input channels only)
Switches the HPF attenuation per octave between -12 dB/oct and -6 dB/oct.
O HA HPF ON indicator
Indicates the HPF on/off status of the external head amp.
P FREQUENCY
Indicates the HPF cutoff frequency of the external head amp.
HPF/EQ window (8ch)
This window displays the input channel or output channel EQ settings in groups of 8 channels
simultaneously. Use the knobs in the SELECTED CHANNEL section to edit the EQ settings.
1 Channel select button
Selects the channel that you want to control. The current channel icon and number
appear on the button, and the channel name appears immediately below the button.
2 EQ graph
Displays the parameter values for the EQ and filter. The currently-selected EQ type
appears below the graph.
3 EQ ON/OFF button
Switches the EQ on or off. The Σ clipping indicator (located to the right above the
button) lights if the input signal is clipping.
4 HPF FREQUENCY knob (input channels only)
Indicates the cutoff frequency of the HPF. Press this button to make adjustments using
the multifunction knob.
5 HPF ON/OFF button (input channels only)
Switches the HPF on or off.
1
2
3
5
4
EQ and Dynamics
V5 Reference Manual
68
HPF/EQ window (CH 1-48, CH 49-72/ST IN (CL5),
CH 49-64/ST IN (CL3), ST IN (CL1), OUTPUT)
This window displays the corresponding input channels (or output channels) simultaneously.
This window is only for display, and does not allow the parameters to be edited. It is useful
when you need to quickly check multiple EQ settings, or when you want to copy and paste EQ
settings between distant channels.
1 Channel select button
Selects the channel that you want to control in the SELECTED CHANNEL section. The
current channel icon, number, and color appear on the button.
2 EQ graph
This field graphically indicates the approximate response of the EQ and filters.
Simultaneously setting EQ type
You can set the EQ type simultaneously for all channels or all racks in the HPF/EQ window
or the PEQ EDIT window. You can select channels by category.
1 GLOBAL SETUP button
Press this button to open the GLOBAL EQ TYPE popup window, where you can set the
EQ type and channel category.
1
2
STEP
1. Press the EQ type select button in the window.
2. Press the GLOBAL SETUP button on the top right side of the popup window.
3. Select an EQ type and channel category in the GLOBAL EQ TYPE window.
4. Press the APPLY button.
5. When the CONFIRMATION dialog box opens, press the OK button.
1
EQ and Dynamics
V5 Reference Manual
69
2 EQ type buttons
Set the EQ type to PRECISE, AGGRESSIVE, SMOOTH, or LEGACY.
3 GLOBAL DESTINATIONS buttons
Set for each category the channels that you set for the selected EQ type. Multiple
selections are possible.
If you select 8BandPEQ, the selected EQ type will be set as the default setting.
Using dynamics
Input channels feature two dynamics processors; output channels feature one dynamics
processor.
NOTE
The DYNAMICS 1/2 field on the OVERVIEW screen displays the dynamics on/off status and the
amount of gain reduction.
Dynamics settings can be saved and recalled at any time using the dedicated library. You can
also take advantage of a wide variety of presets suitable for various instruments or situations.
You can also access the SELECTED CHANNEL VIEW screen, and use the knobs in the
SELECTED CHANNEL section to edit the dynamics settings (page 10).
Even when the DYNAMICS 1/2 window is displayed, you can use the knobs in the SELECTED
CHANNEL section to control the dynamics.
2
3
STEP
1. Use the Bank Select keys to select the channel for which you want to control the
dynamics.
2. Press the DYNAMICS 1/2 field in the OVERVIEW screen.
3. Press the 1 ch tab in the DYNAMICS1/2 window.
4. Press the DYNAMICS ON button, and adjust the dynamics parameters.
OVERVIEW screen DYNAMICS 1/2 window
Dynamics 1
field
Dynamics 2
field
EQ and Dynamics
V5 Reference Manual
70
DYNAMICS 1/2 window (1ch)
All dynamics parameters can be viewed and edited by channel. This is convenient when you
want to make detailed dynamics settings for a specific channel.
1 LIBRARY button
Press this button to open the DYNAMICS Library window.
2 DEFAULT button
Press this button to reset all dynamics parameters to the initial values.
3 COPY button
All dynamics parameter settings will be copied in buffer memory.
4 PAST E bu tton
Press this button to apply the settings in buffer memory to the current dynamics. If no
valid data has been copied in the buffer memory, nothing will happen.
5 COMPARE button
Press this button to swap between the current dynamics settings and the data stored in
buffer memory. If no valid data has been copied in the buffer memory, nothing will
happen.
NOTE
For details on how to use buttons 1 - 5, refer to “Using the tool buttons” in the separate Owner’s
Manual.
6 Channel icon/Channel number/Channel name
This area indicates the icon, number, and name of the currently-selected channel.
7 Dynamics type buttons
Enables you to select the dynamics type. You can choose from the following dynamics
types.
Dynamics 1 for an input channel
GATE, DUCKING, COMPRESSOR, EXPANDER
Dynamics 2 for an input channel
COMPRESSOR, COMPANDER-H, COMPANDER-S, DE-ESSER
Dynamics 1 for an output channel
COMPRESSOR, EXPANDER, COMPANDER-H, COMPANDER-S
8 Dynamics graph
Displays the input/output response of the dynamics processors.
9 Dynamics parameter setting knobs
Indicates the dynamics parameter values. You can adjust the values by using the
multifunction knobs. The type of parameters will vary depending on the currently-
selected dynamics type.
GATE or DUCKING:
COMPRESSOR or EXPANDER:
COMPANDER-H or COMPANDER-S:
DE-ESSER:
0 Dynamics IN/OUT level meters, GR meter
These meters indicate the peak level of the signals before and after the dynamics
processing, and the amount of gain reduction. For a stereo channel, these meters
indicate the level of both the L and R channels.
1 2 3 4 58
6
7
9
C
A
B
0
D
EQ and Dynamics
V5 Reference Manual
71
A KEY IN SOURCE select button
Press this button to display the KEY IN SOURCE window, in which you can select a key-
in signal that will trigger the dynamics.
SELF PRE EQ ......... The pre-EQ signal of the same channel
SELF POST EQ ....... The post-EQ signal of the same channel
MIX OUT 21-24 ........ Output signals of MIX channels 21-24
CH 1-72 POST EQ, ST IN 1L-8R POST EQ, MIX 1-24 POST EQ,
MTRX 1-8 POST EQ, ST L/R, MONO POST EQ
........The post-EQ signal of the corresponding channel
*1
*1 Choose from a group of eight channels.
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
B KEY IN FILTER parameter area (Displayed only for Dynamics 1 for an input
channel)
Enables you to make various settings for a filter that lets the key-in signal pass.
Filter select buttons ............. Select the type of filter from HPF, BPF, or LPF. To
disable the filter, press the button that is turned on.
Q knob................................... Indicates the filter Q. You can adjust the value by using
the multifunction knob.
FREQUENCY knob ............... Indicates the filter cutoff frequency. You can adjust the
value by using the multifunction knob.
C KEY IN CUE button (Displayed only for Dynamics 1 for an input channel)
Enables you to cue-monitor the signal that has been selected as the KEY IN SOURCE
signal. Cue will be canceled if you have selected a dynamics type that does not feature
this button, or if you move to a different screen.
NOTE
The cue monitoring does not support CUE B.
D Tabs
Use these tabs to select a channel that you want to view on the screen.
DYNAMICS1/2 window (8ch)
This window displays the input channel or output channel dynamics settings in groups of 8
channels simultaneously. This window is convenient if you want to adjust the threshold or
certain other parameters while watching the adjacent channels to the left and the right.
1 Channel select button
Selects the channel that you want to control. The current channel icon and number
appear on the button, and the channel name appears immediately below the button.
2 DYNAMICS OUTPUT meters, GR meter
Indicate the output levels of signals after dynamics processing, and the amount of gain
reduction. If GATE is selected as the dynamics type, a three-step indicator appears,
indicating the open/close status of the gate.
If GATE is selected as the dynamics type, the indicator status means the following:
Gate status
Red Yellow Green Off (dark)
On/Off status On On On Off
Open/Close
status
Close Open Open -
Amount of gain
reduction
30 dB or more less than 30 dB 0 dB -
1
2
4
5
3
Type = Any type other than GATE
Type = GATE
EQ and Dynamics
V5 Reference Manual
72
3 Dynamics graph
Indicates the dynamics parameter values. The currently-selected dynamics type appears
below the graph. Press the graph to access the DYNAMICS 1ch window for that
channel.
4 THRESHOLD knob
Indicates the threshold value for the dynamics. You can use the multifunction knobs to
operate this.
5 DYNAMICS ON/OFF button
Switches dynamics on or off.
DYNAMICS 1/2 window (CH 1-48, CH 49-72/ST IN (CL5), CH 49-
64/ST IN (CL3), ST IN (CL1), OUTPUT)
This window enables you to make settings of the global dynamics parameters for the
corresponding channel.
1 Channel select button
Selects the channel that you want to control. The current channel icon, number,
threshold, and color appear on the button.
2 Dynamics parameter area
This area displays the dynamics type and various meters. Press the area to access the
DYNAMICS 1ch window of that channel.
If DUCKING, EXPANDER, COMPANDER (-H/-S), or DE-ESSER has been selected as the
dynamics type, the type appears near the top of this area.
The lower part of this area displays meters that indicate the levels of signals after
dynamics processing, the GR meter, and the threshold (a numeric value). If the
dynamics processor is any type other than GATE, the threshold setting is indicated as a
vertical line.
1
2
EQ and Dynamics
V5 Reference Manual
73
Using the EQ/Dynamics libraries
You can use dedicated libraries to store and recall EQ and dynamics settings. For details on
using the EQ and dynamics libraries, refer to the “Using the library” section in the separate
Owner’s Manual.
EQ library
There is an “INPUT EQ LIBRARY” that lets you store/recall EQ
settings for input channels, and an “OUTPUT EQ LIBRARY” that
lets you store and recall EQ settings for output channels.
To recall settings from a library, press the LIBRARY tool button in
the /HPF/EQ window.
NOTE
You can recall 199 different settings from both the input EQ library and output EQ library. Forty
(40) of the input library items are read-only presets, and three (3) of the output library items are
read-only presets.
Dynamics library
Use the “Dynamics Library” to store and recall dynamics settings. All of the dynamics
processors on CL series units use this dynamics library. (However, the available types will
differ between an input channel’s Dynamics 1 and Dynamics 2, and an output channel’s
Dynamics 1. You can’t recall a type that cannot be used.
To recall an item from the dynamics library, press the LIBRARY tool button in the DYNAMICS
1/2 window.
NOTE
You can recall 199 different settings from the library. Forty-one (41) of these are read-only presets.
LIBRARY button
Channel Job
V5 Reference Manual
74
Channel Job
This chapter explains the DCA Group and Mute Group functions that enable you to control the
level or muting of multiple channels together, the Channel Link function that links the
parameters of multiple channels, and the operations that enable you to copy or move
parameters between channels.
DCA group
CL series consoles feature sixteen DCA groups that enable you to control the level of multiple
channels simultaneously.
DCA groups enable you to assign input and output channels to sixteen groups, so that the
Centralogic section faders 1 - 8 can be used to control the level of all channels in each group.
A single DCA fader will control the level of all input channels belonging to the same DCA group
while maintaining the level difference between the channels. This provides a convenient way
in which drum mics, for example, can be grouped.
Assigning channels to a DCA group
There are two ways to assign a channel to a DCA group.
You can select a specific DCA group and then specify the channels to be assigned to the
group, or
You can select a specific channel and then specify the DCA group to which it should be
assigned.
NOTE
DCA group settings are saved as part of the scene.
With CL V3.0 and later, you can now assign the Stereo/Mono bus master, Mix bus master, and
Matrix bus master channels to a DCA group on channels other than input channels. DCA groups
were formerly used exclusively for input channels. However, with this new feature, you can use
the DCA groups for output master channels, which enables for more flexible simultaneous
controls.
Selecting the channels that will belong to a specific DCA group
NOTE
You can also access the DCA/MUTE GROUP ASSIGN MODE window by pressing the DCA/
MUTE GROUP field in the OVERVIEW screen.
You can assign a single channel to more than one DCA group. In this case, the value will be the
sum of the levels of all assigned DCA group faders.
The DCA/MUTE GROUP field of the OVERVIEW screen indicates the DCA group(s) to which
each channel is assigned. Numbers that are lit yellow in the upper and middle row of this field
indicate the DCA groups to which that channel belongs.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the DCA GROUP button.
3. Use the DCA GROUP select button to select the DCA group to which you want to
assign channels.
4. Use the [SEL] keys in the INPUT section or ST IN section to select the channels that
you want to assign to the group (multiple selections are allowed).
Function
Access Area
CH JOB
menu
Channel Job
V5 Reference Manual
75
DCA/MUTE GROUP ASSIGN MODE window
Here you can specify the channels that will be assigned to each DCA group.
1 DCA GROUP ASSIGN/MUTE GROUP ASSIGN buttons
Toggle between the DCA GROUP ASSIGN window and MUTE GROUP ASSIGN window.
2 DCA group assign field
This area displays the channels assigned to the currently-selected DCA group.
While this window is displayed, press the [SEL] key for the channel that you want to
assign to the DCA group. The channel will be assigned to the DCA group, and the on-
screen fader for that channel will turn yellow. Press the same [SEL] key once again if you
want to remove the channel from the group.
NOTE
In the case of the CL3/CL1, faders that do not exist on those models will not be shown.
3 NAME EDIT button
Edits the group name of the currently-selected DCA group.
When you press this button the keyboard window will appear, allowing you to enter or
edit the text.
The DCA group name is displayed on the DCA group select button.
The registered group name is displayed on the PATCH/NAME tab in the RECALL SAFE
MODE popup window.
4 DCA group select button
Selects the DCA group that you want to assign.
5 CLEAR ALL button
Clears all channels that are assigned to the currently-selected DCA group.
6 DCA ROLL-OUT button
Enter the DCA ROLL OUT mode.
This function enables flexible fader operations. For example, while controlling the DCA
fader in the Centralogic section, you can access (roll-out) and control the faders
(assigned to the corresponding DCA group) through the fader bank located to the left
of the Centralogic section. Alternatively, you can control the faders rolled out to the
Centralogic section via DCA Roll-out, while operating the DCA faders through the fader
bank on the left.
7 PRE&POST button
Specifies the object of muting in the DCA group as PRE and POST.
The PRE&POST indicator is shown below a DCA group that has this setting.
8 POST ONLY button
Specifies the object of muting in the DCA group as POST only.
NOTE
You can set the object of muting in the DCA group individually for each DCA group.
If you mute any of the DCA groups on a channel assigned to multiple DCA groups, the signal
route for that channel (including sends to the corresponding bus) will be muted.
9 CLOSE button
Closes the window.
2
3
4
7
6
5
1
89
Channel Job
V5 Reference Manual
76
Selecting the DCA groups to which a specific channel will belong
Controlling DCA groups
Use the faders of the Centralogic section to control DCA groups.
NOTE
You can also press the [DCA], [DCA 1-8], or [DCA 9-16] key in the Channel Strip section to select
the DCA group that you want to control.
In the DCA member display on the OVERVIEW screen, you can use the multifunction knob in the
Centralogic section to scroll through channels when there are 15 or more channels assigned.
Using DCA groups
Use the Centralogic section to operate the DCA group.
Level adjustment: Faders.... The level of the channels assigned to that DCA group
can be adjusted while preserving the level differences
of each channel. The input faders will not operate at
this time.
On/Mute switch: [ON] key.... When you press an [ON] key in the Centralogic section
to make the key indicator go dark, the channels
assigned to that DCA group will be muted (the same
state as when the faders are lowered to the -∞ dB
position).
Cue Monitor: [CUE] key ....... When you press the Centralogic section [CUE] key to
make it light, the [CUE] keys of the channels assigned
to that DCA group will blink, and cue monitoring will be
enabled. For more information about cue, refer to
Using the Cue function” (page 120).
STEP
1. Press the [SEL] key of the input channels and output channels that you want to
operate.
2. Press one of the knobs in the SELECTED CHANNEL section.
3. Use the DCA group select buttons in the SELECTED CHANNEL VIEW screen to select
the DCA group(s) to which the currently-selected channel will be assigned (multiple
selections are allowed).
STEP
1. Assign input and output channels to DCA groups.
2. Using the faders in the Channel Strip section or Master section on the top panel,
adjust the relative balance between the input and output channels that belong to
the DCA group you want to use.
3.
Use the Bank Select keys in the Centralogic section to select the [DCA 1-8] key or the
[DCA 9-16] key.
4. Use the Centralogic section to operate the DCA group.
SELECTED CHANNEL
VIEW screen
DCA/MUTE
field
Channel Job
V5 Reference Manual
77
DCA Roll-out function
You can now access all of the channels assigned to a DCA group simultaneously through the
fader banks.
This function enables flexible fader operations. For example, while controlling the DCA fader
in the Centralogic section, you can use the Roll-out function to access (roll-out) and control
the faders (assigned to the corresponding DCA group) through the fader bank located to the
left of the Centralogic section. Alternatively, you can control the faders rolled out to the
Centralogic section via DCA Roll-out, while operating the DCA faders through the fader bank
on the left.
DCA ROLL-OUT operation
NOTE
You cannot turn Roll-out mode on while operating the DCA group (for example, while assigning
channels or editing the group name).
Even if Roll-out mode is turned on while you are controlling a GEQ via faders, you cannot edit
the DCA group using the faders.
If the number of channels assigned to the DCA group exceeds the number of faders in the block,
you can use the multifunction knob or the GAIN/PAN/ASSIGN knob to scroll the content of the
block from left to right. While the knob is turned, the message “DCA ROLL-OUT: DCA members
scrolling.” is displayed at the bottom of the screen.
If, for example, the DCA group to be operated is in the Centralogic section and the HPF/EQ
window is displayed, the HPF/EQ parameters for the multifunction knob cannot be operated.
To operate a parameter that is not assigned, use the USER DEFIND knob assigned the TOUCH
AND TURN function.
All bank select keys in the block (to which the displayed channels belong) will light up.
If the faders are rolled out to the Centralogic section (block B), the IN/OUT select keys in the
Centralogic section will be disabled.
Bank select keys in blocks in which no faders are rolled out will operate normally.
When in DCA ROLL-OUT mode, you can exit this mode by pressing a Bank Select key. In that
case, the screen will switch to the bank for the key that was pressed.
Setting the DCA Roll-out function
NOTE
You cannot turn DCA Roll-out mode on if one of the following popup windows is open. If DCA
Roll-out mode is already turned on, opening one of the windows will cause DCA Roll-out mode
to quit.
- DCA/MUTE GROUP ASSIGN MODE popup window
- RECALL SAFE MODE popup window
STEP
1.
Use a bank select key to select the DCA group that you want to control, then press the
[SEL] key for that DCA group.
DCA Roll-out mode is engaged, and the faders that have been assigned to the DCA group will be
rolled out.
2. If you press the [SEL] key for another DCA group, faders that have been assigned to that
DCA group will be rolled out.
3. Press the same [SEL] key again to exit DCA Roll-out mode.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the DCA GROUP button to access the DCA/MUTE GROUP ASSIGN MODE popup
window.
3. Press the DCA ROLL-OUT button.
4. Select a DCA group.
If you press a [SEL] key for a DCA group other than the selected one, the group selection will change.
5. Select a block (in which the DCA group is rolled out to the faders) and the alignment.
6. Press the CLOSE button to close the popup window.
Function
Access Area
ASSIGN MODE popup window
Channel Job
V5 Reference Manual
78
DCA ROLL-OUT screen
1 ROLL-OUT BLOCK
Enables you to select a block in which the DCA group is rolled out to the faders.
CL5 : Blocks A, B, C
CL3/CL1 : Blocks A, B
2 ALIGN button
Enables you to choose whether the DCA group is rolled out to the faders from the left
or right.
3 DCA group select button
Selects the DCA group that you want to control.
Using the temporary unmute function
If one of the DCA group buttons on a channel is OFF (muted), press the [ON] key for that
channel to temporarily unmute the channel. However, in Preview mode, any operation during
mute with pressing of the [ON] key is disabled.
Example 1: CH 1 is OFF. Assigned to DCA GROUP 1.
Example 2: CH 1 is ON. Assigned to MUTE GROUP 1 and DCA GROUP 1.
2
1
3
Operation Example 1
1. Press the ON key for DCA 1. The indicator lamp goes off.
The indicator lamp for the ON key for CH 1 remains off. DCA 1 is muted.
2. Press the ON key for CH 1.
CH 1 is temporarily unmuted, and the indicator lamp for the ON key comes on.
3. Press the ON key for DCA 1. The indicator lamp comes on.
DCA 1 is unmuted, and the indicator lamp for the ON key for CH 1 comes on.
Operation Example 2
1. Set MUTE MASTER 1 to ON (MUTE).
CH 1 is muted, and the ON key flashes.
2. Press the ON key for CH 1.
CH 1 is temporarily unmuted, and the indicator lamp for the ON key comes on.
3. Press the ON key for DCA 1. The indicator lamp goes off.
CH 1 is muted, and the ON key flashes.
4. Press the ON key for CH 1.
CH 1 is temporarily unmuted, and the indicator lamp for the ON key comes on.
5. Press the ON key for CH 1 again.
CH 1 is muted again, and the ON key flashes.
6. Set DCA1 to ON, and MUTE MASTER 1 to OFF.
CH 1 is unmuted, and the indicator lamp for the ON key comes on.
Channel Job
V5 Reference Manual
79
Mute group
CL series consoles feature eight mute groups.
Mute groups enable you to use USER DEFINED keys [1]-[16] to mute or unmute multiple
channels in a single operation. You can use this to cut out multiple channels simultaneously.
Mute groups 1 - 8 can be used with both input channels and output channels. Both types of
channels can exist in the same group.
Assigning channels to mute groups
As with the DCA group, there are the following two ways to assign channels to mute groups.
You can select a specific mute group first and then specify the channels to be assigned to
the group, or
You can select a specific channel and then specify the mute group to which it should be
assigned.
Selecting the channels that will belong to a specific mute group
NOTE
You may assign a single channel to more than one mute group.
The DCA/MUTE GROUP field of the OVERVIEW screen indicates the mute group(s) to which
each channel is assigned. Numbers that are lit red in the lower line of this field indicate the mute
groups to which that channel belongs.
If the dimmer level is set to any level other than -∞ dB, these numbers will light orange.
For a channel for which the Mute Safe function (page 82) has been turned on, an “S” indicator
will light up green at the right end of the bottom row.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the MUTE GROUP button in the CH JOB menu.
3. Use the mute group master buttons in the DCA/MUTE GROUP ASSIGN MODE
window to select the mute group to which you want to assign channels.
4. Press the [SEL] key for the input channels/output channels that you want to operate
(multiple selections are allowed).
Function
Access Area
CH JOB
menu
Channel Job
V5 Reference Manual
80
DCA/MUTE GROUP ASSIGN MODE window
Here you can select the channels that will be assigned to each mute group.
1 DCA GROUP ASSIGN/MUTE GROUP ASSIGN buttons
Toggle between the DCA GROUP ASSIGN window and MUTE GROUP ASSIGN window.
2 Mute group assign field
This area displays the channels assigned to the currently-selected mute group.
While this window is displayed, press the [SEL] key for the channel that you want to
assign to the mute group. The channel will be assigned to the mute group, and the on-
screen fader for that channel will turn red. Press the same [SEL] key once again if you
want to remove the channel from the group.
If the MUTE SAFE button is on, this field displays the channels that enabled for mute safe
(that is, excluded from the mute groups). The operation procedure to apply or cancel
mute safe to the channels is the same as that for assigning or removing channels to or
from a mute group. The on-screen faders of the assigned channels will turn green.
3 NAME EDIT button
Edits the group name of the currently-selected mute group.
When you press this button the keyboard window will appear, allowing you to enter or
edit the text.
The mute group name is displayed on the mute group select button.
4 Mute group select button
Selects the mute group that you want to assign.
5 MUTE GROUP MASTER button
Switches the mute for the corresponding mute group on or off.
6 DIMMER LEVEL knob
Sets the dimmer level for the corresponding mute group when the dimmer function is
enabled.
NOTE
In the case of the CL3/CL1, faders that do not exist on those models will not be shown.
If the dimmer level is set to any level other than -∞ dB, and the corresponding MUTE GROUP
MASTER button is turned on, this button will light orange.
7 CLEAR ALL button
Clears all channels that are assigned to the currently-selected mute group.
8 MUTE SAFE button
Use this button when you want to temporarily exclude a specific channel from all mute
groups. The mute group assign field displays the channels that are temporarily excluded
from the mute groups. For more information on mute safe, refer to “Using the Mute
Safe function” (page 82).
9 CLOSE button
Closes the window.
Selecting the mute groups to which a specific channel will belong
2
6
5
4
3
8
7
1
9
STEP
1. Press the [SEL] key of the input channels and output channels that you want to
operate.
2. Press one of the knobs in the SELECTED CHANNEL section.
3. Use the mute group select buttons in the SELECTED CHANNEL VIEW screen to select
the mute group(s) to which the currently-selected channel will be assigned.
(Multiple selections are allowed.)
SELECTED CHANNEL
VIEW screen
DCA/MUTE
field
Channel Job
V5 Reference Manual
81
Using mute groups
To control mute groups, you can use the MUTE GROUP MASTER buttons in the MUTE
GROUP ASSIGN window. In addition, it may prove convenient if you assign the Mute On/Off
function for a mute group 1 - 8 to a USER DEFINED key.
Assigning mute groups to USER DEFINED keys
NOTE
The USER SETUP window enables you to limit available functionality by user, and also to make
system-wide settings. This window includes several pages, which you can switch between using
the tabs located at the bottom of the window.
Turning mute groups on/off with USER DEFINED keys
To mute a mute group, press the USER DEFINED key to which you have assigned the Mute
On/Off function.
The LED of the USER DEFINED key will light, and all channels that belong to the selected
mute group will be muted. At this time, the [ON] key of the muted channels will blink. You can
turn on multiple USER DEFINED keys to mute multiple mute groups.
To defeat muting for a mute group, press the USER DEFINED key that you lit.
NOTE
Even if a channel is assigned to a mute group, it will not be affected by operations of the USER
DEFINED key if the [ON] key for that channel is already turned off to begin with.
Temporarily unmuting a channel
You can unmute a muted channel in the mute group temporarily.
STEP
1. In the Function Access Area, press the SETUP button.
2. Press the USER SETUP button in the upper left of the SETUP screen.
3. In the USER SETUP window, press the USER DEFINED KEYS tab.
4. Press the button for the USER DEFINED key to which you want to assign the Mute
On/Off function.
5. Choose “MUTE MASTER” in the FUNCTION column, and choose “MUTE GROUP x”
(where “x” is the mute group number) in the PARAMETER 1 column.
6.
When you press the OK button, the Mute On/Off function will be assigned to the USER
DEFINED key that you selected in step 4.
USER DEFINED KEY SETUP window
SETUP screen USER SETUP window
Channel Job
V5 Reference Manual
82
Using the Mute Safe function
Specific channels that belong to a mute group can be temporarily excluded from mute group
operations (Mute Safe). Channels that are set to Mute Safe will not be affected when you mute
a mute group to which that channel belongs.
NOTE
The [SEL] key of the channel set for Mute Safe will light, and the on-screen fader for that channel
will be highlighted in green. You can cancel the Mute Safe status by pressing a lit [SEL] key once
again to make it go dark.
Using the temporary unmute function
If one of the mute group master buttons on a channel is ON, press the [ON] key for that
channel to temporarily unmute the channel. However, in PREVIEW mode, any operation
during mute with pressing of the [ON] key is disabled.
Using the Recall Safe function
“Recall Safe” is a function that excludes only specific parameters/channels (DCA groups) from
Recall operations. Unlike the Focus Recall function (page 105), which you can apply to
individual scenes, the Recall Safe settings are globally applied to all scenes.
NOTE
Simply selecting a parameter in step 4 does not enable Recall Safe. To turn Recall Safe on or off,
you must also perform the operation described in step 5.
Channel Link (page 85) and bus settings are not subject to Recall Safe; they will always be
reproduced in the recalled scene.
This means that if Recall Safe is enabled for one of several channels included in a link group or
one of two channels set to stereo, the parameter settings of that channel may differ from those of
the other channel(s). In such cases, the applicable parameter will be automatically re-linked the
next time it is operated.
You can globally apply Recall Safe to channel links by using the global parameter.
You can use the Recall Safe function along with the Focus Recall function (
page 105). Channels
or parameters that are excluded from Recall operations by either Focus or Recall Safe will not be
recalled.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the MUTE GROUP button in the CH JOB menu.
3. Press the MUTE SAFE button in the DCA/MUTE GROUP ASSIGN MODE window.
4. Press a [SEL] key for the channel(s) you want to exclude from mute groups (multiple
selections are allowed).
DCA/MUTE GROUP ASSIGN
MODE window
CH JOB
menu
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the RECALL SAFE button in the CH JOB menu.
3. Press the [SEL] key for the channel or DCA group that will be affected by Recall Safe
operations.
4. Use the Safe Parameter select button in the RECALL SAFE MODE window to select
the target for Recall Safe operations.
5. To enable Recall Safe for the selected channel, turn the SAFE button on. (If you
selected a DCA group, turn on either the LEVEL/ON button or the ALL button.)
6. To enable Recall Safe for global parameters, turn on the buttons of the GLOBAL
RECALL SAFE field.
7. When you have finished making settings, press the CLOSE button to close the
window. Then perform a Recall operation.
Function
Access Area
CH JOB
menu
Channel Job
V5 Reference Manual
83
If you perform a Recall operation while holding down a [SEL] key, the Recall Safe settings for the
corresponding channel will temporarily be enabled for that Recall operation.
RECALL SAFE MODE window
1 CLEAR ALL button/SET ALL button
The CLEAR ALL button turns off (disables) the Recall Safe function (that is currently set
for individual channels) and the Global Recall Safe function simultaneously. The SET ALL
button turns on (enables) these functions simultaneously.
NOTE
If you press the CLEAR ALL button, the Recall Safe function will temporarily be disabled.
However, the parameters that would be affected by the Recall Safe function will not change.
2 Safe channel display section
Indicates the channels that are currently set to Recall Safe.
3 SET BY SEL button
Enables you to use the [SEL] keys on the panel to select channels that will be affected by
the Recall Safe function. Turn this button on, and then press the [SEL] key for the
channel to which you want to apply Recall Safe. Recall Safe will turn on. Press the same
[SEL] key once again to de-select the channel.
4 GLOBAL RECALL SAFE display section
Indicates the parameters and racks that will be affected by the Recall Safe function for
all scenes. Press this section to open the GLOBAL RECALL SAFE window.
These buttons correspond to the following parameters.
NOTE
If a dual-type GEQ rack or Premium rack has been selected, you can apply Recall Safe to rack
A and B individually. For other racks, the setting for racks A and B will be linked.
5 Channel select button
Selects the channel for which you want to set the Recall Safe function.
NOTE
Switching channels using this button will not affect the channel selection on the top panel.
6 Selected channel display
This area indicates the icon, number, color, and name of the currently-selected channel.
1
3
5
9
2 4
6
7 0A 8
All parameters are affected by Recall Safe on these channels.
Some parameters are affected by Recall Safe on these channels.
Recall Safe has been canceled on these channels.
HA/ PATC H
INPUT PATCH All input patches
OUTPUT PATCH All output patches
CASCADE IN CASCADE IN PATCH and CASCADE IN ATT settings
CASCADE OUT CASCADE OUT PATCH settings
INPUT NAME All input channel names
OUTPUT NAME All output channel names
HA
All I/O devices, and HA-related parameters for external
head amps
CUSTOM FADER
BANK
Custom fader bank settings
RACK
GEQ RACK
EFFECT RACK
PREMIUM RACK
Apply Recall Safe to GEQ racks 1 - 16, Effect racks 1 - 8,
Premium racks 1- 8 individually.
BUS SETUP
MIX
Sets Recall Safe for MIX 1-24 in the BUS SETUP window.
This setting is applied to a channel pair (one odd-numbered
channel and one even-numbered channel).
MATRIX
Sets Recall Safe for MATRIX 1-8 in the BUS SETUP
window. This setting is applied to a channel pair (one odd-
numbered channel and one even-numbered channel).
SURROUND
SETUP
Surround mode settings.
OTHERs
CH LINK All channel link group settings
MUTE GROUP
NAME
All Mute group names
FADER BANK
SELECT
FADER BANK selection status, MASTER FADER assign
status
Channel Job
V5 Reference Manual
84
7 APPLY TO ALL INPUT button (input channels only)
Turn on this button to apply the Recall Safe parameter selection for one input channel
to all other input channels.
Turn this on if you want to apply Recall Safe to the same parameters for all input
channels.
8 APPLY TO ALL OUTPUT button (shown only for output channels)
Turn on this button to apply Recall Safe parameter selection for one output channel to
all other output channels.
Turn this on if you want to apply Recall Safe to the same parameters for all output
channels.
9 Safe parameter select button (excluding DCA groups)
Selects Recall Safe parameters for the selected channel.
The button indication varies depending on the channel type.
Input channel
NOTE
ST IN channels do not feature INSERT, INSERT PATCH, and DIRECT OUT button.
MIX channel
MATRIX channel
STEREO channel
MONO channel
If Recall Safe is turned on for global parameters, the safe parameter select buttons of the
selected channel will light green, as follows.
This figure indicates that the INPUT PATCH, INSERT PATCH, and DIRECT OUT
parameters have been set to Safe by the INPUT PATCH Global parameter settings.
In the same way, turning on the Global parameters INPUT NAME, OUTPUT PATCH, and
OUTPUT NAME will cause the corresponding safe parameters of each channel to light
green. On-screen buttons and corresponding parameters apply to the following
channels:
Button name Corresponding parameter
Input
channel
MIX
channel
MATRIX
channel
STEREO/
MONO
channel
WITH MIX SEND Send level to the MIX bus O
WITH MATRIX
SEND
Send level to MATRIX bus
O
ALL
*1
All parameters O O O O
HA HA-related settings O
HPF HPF settings O
EQ EQ settings O OOO
DYNA 1 Dynamics 1 settings O O O O
DYNA 2 Dynamics 2 settings O
MIX SEND Send level to MIX bus O
MATRIX SEND Send level to MATRIX bus O O O
FADER Fader settings O O O O
CH ON [ON] key settings O O O O
TO ST
On/off setting for STEREO bus
assignment, PAN, etc.
OO
MONO
On/off setting for MONO bus
assignment
OO
INPUT PATCH Input patch settings O
Channel Job
V5 Reference Manual
85
*1. The default setting is ALL on.
*2. ST IN channels do not feature these buttons.
*3. When these buttons are turned on, the settings registered for the DCA group are targeted for RECALL SAFE.
Settings for DCA 1-16 are made simultaneously. Settings are linked according to the channel link for the
current scene when the settings are made.
9 Safe parameter select button (DCA)
For each DCA group, selects the parameters for which Recall Safe is enabled. If the ALL
button is on, all DCA master parameters will be subject to Recall Safe. If LEVEL/ON is on,
Recall Safe will apply to the DCA master level and on/off status. If NAME is on, Recall
Safe will apply to the DCA group name. Although you can turn on both the LEVEL/ON
button and the NAME button, they will then both be switched off if you turn on the ALL
button.
0 SAFE button (excluding DCA groups)
When this button is turned on, Recall Safe will be enabled for the selected channel.
NOTE
Even if a parameter is selected with the Safe Parameter Select button, Recall Safe will not be
enabled if this button is off.
A CLOSE button
Closes the window.
Channel Link function
Channel Link is a function that links the operation of parameters such as fader and EQ
between input and output channels. Two or more channels that are linked are called a “link
group”. There is no limit on the number of link groups you can create, or on the number and
combinations of channels that can be included in these link groups. You can select the types
of parameters to be linked for each link group. However, input channels and output channels
cannot coexist on the same link group.
The parameters to be linked can be selected from the following choices.
For an input channel:
Head amp settings
Digital gain settings
HPF settings
EQ settings
Dynamics 1 settings
Dynamics 2 settings
Insert on and insert point settings
Direct Out on, Direct Out level, and Direct Out point settings
Send levels and PRE/POST settings of signals sent to MIX buses
On/off status of signals sent to MIX buses
Send levels and PRE/POST settings of signals sent to MATRIX buses
On/off status of signals sent to MATRIX buses
Fader operations
[ON] key operations
TO STEREO/MONO setting
•DELAY setting
DCA GROUP ASSIGN setting
MUTE GROUP ASSIGN settings
For an output channel:
EQ settings
Dynamics settings
Insert on and insert point settings
Send levels and PRE/POST settings of signals sent to MATRIX buses
*1
On/off status of signals sent to MATRIX buses
*1
Fader operations
[ON] key operations
TO STEREO/MONO setting
*1
DCA GROUP ASSIGN setting
MUTE GROUP ASSIGN settings
*1 MATRIX channel not applicable
DIGITAL GAIN Digital gain settings O
INSERT Insert on/off O
*2
OOO
INSERT PATCH Insert patch settings O
*2
OOO
DIRECT OUT Direct Out settings O
*2
MIX ON MIX Send On/Off O
MATRIX ON MATRIX Send On/Off O O O
DELAY Delay settings O
NAME Channel name O O O O
OUTPUT PATCH Output patch settings O O O
BAL BLANCE parameter settings O
O
(STEREO only)
DCA ASSIGN
*3
Settings registered in DCA
group
OOOO
MUTE ASSIGN
Settings registered in MUTE
group
OOOO
Button name Corresponding parameter
Input
channel
MIX
channel
MATRIX
channel
STEREO/
MONO
channel
Channel Job
V5 Reference Manual
86
Linking the desired input channels
This section explains how to link specific parameters of input channels.
NOTE
Channel link settings are saved as part of the scene.
NOTE
You can also access the CH LINK MODE window by simultaneously pressing and then releasing
the [SEL] keys of two or more channels that will be linked.
When you press the [SEL] key for a channel (that belongs to a link group) to make it light, the
[SEL] keys of all channels that belong to the same link group will blink.
If you link an input channel to a ST IN channel, parameters that do not exist for a ST IN channel
will be ignored.
CH LINK MODE window (input channels)
You can view the input channels that are linked and specify the parameters that will be linked.
1 Input channel display field
When you create a link group, the corresponding input channels will be highlighted. If
there are two or more link groups, each group is shown in a different color. Press this
field to open the CH LINK SET window. You can also link input channels in this window.
NOTE
Left and right of the ST IN channel are always linked.
In the case of the CL3 and CL1, faders that do not exist on those models will not be shown.
2 Link indicator
If an input channel belonging to a link group is selected, the associated link group is
shown. The LINK PARAMETER field and SEND PARAMETER field show the link settings.
While you hold down the [SEL] key of an input channel that does not belong to any link
group, the link indicator shows the link group that will be created next. The LINK
PARAMETER field and SEND PARAMETER field show the settings of the link group that
had been previously displayed.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the CH LINK button in the CH JOB menu.
3. To link channels, hold down the [SEL] key for the link-source input channel and press
the [SEL] key for the link-destination channel.
4. Use the buttons of the LINK PARAMETER field in the CH LINK MODE window to
select the parameter(s) that will be linked (multiple selections are allowed).
5. If you turned on the MIX ON, MIX SEND, MATRIX ON, or MATRIX SEND buttons in
step 4, use the buttons of the SEND PARAMETER field to specify the bus(es) for
which you want operations to be linked (multiple selections are allowed).
Function
Access Area
CH JOB
menu
5
2
3
1
4
Channel Job
V5 Reference Manual
87
3 LINK PARAMETER field
Use the buttons in this field to select the parameters that you want to be linked. You can
do this independently for each link group.
The table below lists the parameters you can select in the LINK PARAMETER field.
NOTE
If you link Dynamics 1 or 2 for two or more input channels, the parameter values will be linked,
but the key-in sources are not linked and can instead be set for each channel. The behavior of
key-in signals is linked in units of 8ch*. For details about dynamics, see “EQ and Dynamics
(page 65).
* Units of 8ch refers to Ch 1-8/Ch 9-16/Ch 17-24/Ch 25-32/Ch 33-40/Ch 41-48/Ch 49-56/Ch 57-64/Ch 65-72/
ST IN 1L-ST IN 4R/ST IN 5L-ST IN 8R.
If you turn on the EQ button or DYNAMICS 1/2 button, library recall operations will also be linked.
The HA analog gain setting and the fader operation will be linked and will maintain the same
relative level difference between the channels.
In the insert settings, the parameters for Insert 1 and Insert 2 are selected together.
4 SEND PARAMETER field
If you have turned on the MIX ON, MIX SEND, MATRIX ON, or MATRIX send buttons
in the LINK PARAMETER field, use the buttons in this field to specify the send-destination
bus(es).
NOTE
If nothing is selected in the SEND PARAMETER field, send on/off and send level will not be
linked.
5 INPUT/OUTPUT button
Use this button to switch between the Input Channels screen and the Output Channels
screen.
Channel link operations
Linking three or more channels
Hold down the link-source [SEL] key and successively press the [SEL] key of each input
channel you want to add to the link group.
Adding a new channel to an existing link group
Hold down any [SEL] key within the group and press the [SEL] key that you want to add
to the group.
NOTE
If the link-destination input channel is already assigned to another link group, its assignment to
the previous group will be canceled, and it will be added to the newly assigned group.
Removing a channel from a link group
Hold down any [SEL] key in the same link group, and press the [SEL] key for the channel
that you want to remove.
Changing the level balance between channels that belong to the same link group
While pressing and holding down the [SEL] key for the desired linked channel, adjust the
parameter value. You can also remove all linked channels from the same link group
temporarily. This can be helpful if you want to edit parameters that are linked to each
other while maintaining the same relative level differences. For example, this may be the
case for parameters such as the HA analog gain and fader. While you are holding down
the [SEL] key, the HA analog gain and fader values will not be linked. (However, you
cannot temporarily cancel this link during the “fading” phase of a recalled scene.)
HA
Head amp settings
However, for wireless devices, the GAIN parameter
for the receiver side is not included.
HPF HPF settings
DIGITAL GAIN Digital gain settings
EQ EQ settings
DYNAMICS 1, 2 Dynamics 1 and 2 settings
INSERT Insert settings
DIRECT OUT Direct Out settings
MIX SEND Send levels of signals sent to MIX buses
MIX ON On/off status of signals sent to MIX buses
MATRIX SEND Send levels of signals sent to MATRIX buses
MATRIX ON On/off status of signals sent to MATRIX buses
FADER Fader operations
DCA DCA group assignment
CH ON Channel on/off
MUTE Mute group assignment
TO STEREO
On/off status of signals sent to STEREO/MONO
buses
DELAY Channel delay settings
MIX 1-24 MIX buses 1-24
MTRX 1-8 MATRIX buses 1-8
Channel Job
V5 Reference Manual
88
CH LINK MODE window (output channels)
You can view the output channels that are linked and specify the parameters that will be
linked.
1 Output channel display field
When you create a link group, the corresponding output channels will be highlighted.
If there are two or more link groups, each group is shown in a different color. Press this
field to open the CH LINK SET window. You can also link output channels in this window.
NOTE
In the case of the CL3 and CL1, faders that do not exist on those models will not be shown.
2 Link indicator
If an output channel belonging to a link group is selected, the associated link group is
shown. The LINK PARAMETER field and SEND PARAMETER field show the link settings.
While you hold down the [SEL] key of an output channel that does not belong to any
link group, the link indicator shows the link group that will be created next. The LINK
PARAMETER field and SEND PARAMETER field show the settings of the link group that
had been previously displayed.
3 LINK PARAMETER field
Use the buttons in this field to select the parameters that you want to be linked. You can
do this independently for each link group.
The table below lists the parameters you can select in the LINK PARAMETER field.
*1 MATRIX channel not applicable
NOTE
If you link Dynamics for two or more output channels, the parameter values will be linked, but the
key-in sources are not linked and can instead be set for each channel. The behavior of key-in
signals is linked in units of 8ch*. For details about dynamics, see “EQ and Dynamics” (page 65).
* Units of 8ch refers to MIX 1 - MIX 8/MIX 9 - MIX 16/MIX 17 - MIX 24/MATRIX 1 - MATRIX 8.
If you turn on the EQ button or DYNAMICS button, library recall operations will also be linked.
In the insert settings, the parameters for Insert 1 and Insert 2 are selected together.
4 SEND PARAMETER field
If you have turned on the MATRIX ON or MATRIX send buttons in the LINK PARAMETER
field, use the buttons in this field to specify the send-destination bus(es).
NOTE
If nothing is selected in the SEND PARAMETER field, send on/off and send level will not be
linked.
5 INPUT/OUTPUT button
Use this button to switch between the Input Channels screen and the Output Channels
screen.
5
2
3
1
4
EQ EQ settings
DYNAMICS Dynamics settings
INSERT Insert settings
MATRIX SEND Send levels of signals sent to MATRIX buses *1
MATRIX ON On/off status of signals sent to MATRIX buses *1
FADER Fader operations
CH ON Channel on/off
TO STEREO On/off status of signals sent to STEREO/MONO buses *1
DCA DCA group assignment
MUTE Mute group assignment
MTRX 1-8 MATRIX buses 1-8
Channel Job
V5 Reference Manual
89
Channel link operations
Linking three or more channels
Hold down the link-source [SEL] key and successively press the [SEL] key of each output
channel you want to add to the link group.
Adding a new channel to an existing link group
Hold down any [SEL] key within the group and press the [SEL] key that you want to add
to the group.
NOTE
If the link-destination output channel is already assigned to another link group, its assignment to
the previous group will be canceled, and it will be added to the newly assigned group.
Removing a channel from a link group
Hold down any [SEL] key in the same link group, and press the [SEL] key for the channel
that you want to remove.
Changing the level balance between channels that belong to the same link group
While pressing and holding down the [SEL] key for the desired linked channel, adjust the
parameter value. You can also remove all linked channels from the same link group
temporarily. This can be helpful if you want to edit parameters that are linked to each
other while maintaining the same relative level differences. While you are holding down
the [SEL] key, the fader values will not be linked. (However, you cannot temporarily
cancel this link during the “fading” phase of a recalled scene.)
CH LINK SET window
Displayed when you press the channel display field in the CH LINK MODE window. You can
also link channels in this window.
1 Channel select button
Select a channel that you want to link. The selected input channel will be indicated in
blue, the selected output channel will be indicated in orange, and the alphabetical
character that indicates the link group will appear for linked channels.
2 LINK buttons
Link the channel selected in, 1.
3 UNLINK button
Cancels the link selected in
, 1.
4 UNSELECT ALL
De-selects all selected channels.
5 CLOSE button
Closes the window.
NOTE
If you use CL5 settings data on the CL3/CL1, or CL3 settings data on the CL1, buttons will be
shown crossed-out if they are assigned to a channel that does not exist on that model.
1
2 3 5 4
When selecting a channel When linking channels
Channel Job
V5 Reference Manual
90
Copying, moving, or initializing a channel
You can copy or move mix parameters between channels, or restore the parameters of a
specific channel to their default settings.
Copying the parameters of a channel
You can copy the mix parameter settings of a channel to another channel. When you execute
the copy operation, the settings will overwrite the parameters of the copy-destination.
You can copy between the following combinations of channels.
Between input channels
Between the STEREO L/R channel and MONO channel
Between MIX channels
Between MATRIX channels
CH COPY MODE window
This window enables you to copy channel settings.
1 SOURCE CH field
Displays the copy-source channel. While this window is displayed, press a [SEL] key on
the top panel to select a channel. The selected channel will be highlighted in this field.
If you want to re-select the copy-source channel, press this field.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the COPY button in the CH JOB menu.
3. Press a [SEL] key to select the copy-source channel.
4. Press the [SEL] key for the copy-destination channel (multiple selections are
allowed).
5. If you have selected a MIX/MATRIX channel as the copy-source, use the buttons in
the COPY TARGET field to select the parameters you want to copy.
6. Press the COPY button to execute the copy.
Function
Access Area
CH JOB
menu
1 4 2 3
Before selection After selection
Channel Job
V5 Reference Manual
91
If the copy source is a MIX/MATRIX channel, buttons will
appear so you will be able to select parameters to copy.
If these buttons are turned on, the following parameters
will be copied:
MODULE PARAMETERS button
Selected channel module parameters
WITH MIX SEND/WITH MATRIX SEND button
SEND parameters of signals sent to the selected channel
2 DESTINATION CHs field
Displays the copy-destination channel. When you specify
the copy source, you can then select a copy-destination
channel (multiple selections are allowed) by pressing its
[SEL] key on the panel, and this field will be highlighted.
If you want to defeat all of the selected copy-destination
channels, press the DESTINATION CHs field.
NOTE
In the case of the CL3/CL1, faders that do not exist on those
models will not be shown.
3 COPY button
Executes the copy operation. After selecting the copy-source channel and copy-
destination channel(s), press this button to execute the copy operation.
4 CLOSE button
Press this button to close the window and return to the previous screen.
Moving the parameters of a channel
The settings of a specific input channel can be moved to a different input channel. When you
execute a Move operation, the numbering of the channels between the move-source and
move-destination will move forward or backward by one.
You can move settings between the following combinations of channels.
Between input channels
Between ST IN channels
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the MOVE button in the CH JOB menu.
3. Press a [SEL] key to select the move-source channel.
4. Press the [SEL] key for the move-destination channel.
5. To execute the move, press the MOVE button.
1 2 3 4 5
1 5 2 3 4
Move by one.
Move
CH JOB
menu
Function
Access Area
Channel Job
V5 Reference Manual
92
CH MOVE MODE window
1 SOURCE CH field
Displays the move-source channel. While this window is displayed, press a [SEL] key on
the top panel to select an input channel. The selected channel will be highlighted in this
field. If you want to re-select the move-source channel, press this field.
2 DESTINATION CH field
Displays the move-destination channel. When you specify the move-source, you can
then select the move-destination input channel by pressing its [SEL] key on the panel.
When the move-destination channel is selected, this field will be highlighted. If you
want to change the move-destination channel, press the [SEL] key for the desired input
channel. If you want to defeat the selected move-destination channel, press the
DESTINATION CH field.
NOTE
In the case of the CL3/CL1, faders that do not exist on those models will not be shown.
3 MOVE button
Executes a move operation. After selecting the move-source channel and move-
destination channel, the channel settings move from the move-source to the move-
destination. The settings of all channels between the move-source and move-
destination will shift toward the move-source by one channel.
4 CLOSE button
Press this button to close the window and return to the previous screen.
1 2
3
4
Channel Job
V5 Reference Manual
93
Initializing the parameters of a channel
You can restore the parameters of a channel to an initialized state. This operation can be
performed on any channel(s).
NOTE
After initialization, the TARGET CHs field will be empty (nothing is selected).
CH DEFAULT MODE window
Enables you to initialize parameters.
1 TARGET CHs field
Indicates the channel selected for initialization. While this window is displayed, press a
[SEL] key on the top panel to select an input channel (multiple selection is allowed). The
field will indicate the selected channel(s). Press the same [SEL] key once again to de-
select the channel.
NOTE
If you press this field while a channel is selected, all selected channels will be de-selected.
In the case of the CL3/CL1, faders that do not exist on those models will not be shown.
2 DEFAULT button
After selecting the channel, press this button to execute the initialization operation.
3 CLOSE button
Press this button to close the window and return to the previous screen.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the DEFAULT button in the CH JOB menu.
3. Press the [SEL] key of the channel(s) to be initialized to make it light (multiple
selections are allowed).
4. Press the DEFAULT button to execute the Initialization.
CH JOB
menu
Function
Access Area
1
3
2
Channel Job
V5 Reference Manual
94
About Mix Minus
The Mix Minus function removes a specific channel signal from the signals sent to the MIX/
MATRIX buses. You can use this function to quickly send monitoring signals to a performer or
announcer simply by removing his or her audio signal.
NOTE
This Mix Minus function is a shortcut for settings, rather than an operation to switch between
modes. Therefore, even after using this function, you can still edit any parameter on the window
without restrictions.
NOTE
You can also access the MIX MINUS popup window by pressing the CH JOB button in the
Function Access Area, then pressing the MIX MINUS button.
STEP
1. Hold the [SEL] key while pressing the MIX/MATRIX bus key in the SELECTED
CHANNEL section.
2. The MIX MINUS popup window will open.
3. If you wish to remove an additional input channel, press the corresponding [SEL]
key.
4. If necessary, in the DESTINATION field, select a bus.
You cannot select a FIXED bus.
5. Press the OK button to set the parameters as follows:
The send level of the signals sent from the selected input channels is lowered to -∞dB.
The send level of the signals sent from all other input channels is set to nominal
(0.0dB).
Send to the destination bus is turned on, and the send point is switched to POST.
For the stereo input channels, the send level of the signal sent from both channels is
set to -∞ dB.
Scene memory
V5 Reference Manual
95
Scene memory
On CL series consoles, you can assign a name to a set of mix parameter and input/output
port patch settings, and store the mix settings in memory (and later recall them from memory)
as a “scene.
Each scene is assigned a number in the range of 000-300. Scene 000 is a read-only scene
used to initialize the mix parameters. Scenes 001-300 are writable scenes.
Each scene contains the position of the top panel faders and [ON] key status, as well as the
following parameters.
Input/output port patching
Bus settings
Head amp settings
EQ settings
Dynamics 1 and 2 settings
Rack (GEQ/Effect/Premium Rack) settings
Pan/balance settings
Insert/Direct Out settings
On/off status and send level of signals sent to MIX buses
On/off status and send level of signals sent to MATRIX buses
DCA group settings
Mute group settings
Channel link settings
The number of the currently-selected scene appears in the SCENE field of the Function
Access Area.
SCENE field
You can press the SCENE field to access the SCENE LIST window, where you can view and
edit more detailed settings for the scene.
1 Scene number
Indicates the number of the currently-selected scene. When you select a new scene
number, the number will blink. This blinking indicates that the displayed scene number
is different than the currently-loaded scene number.
2 R symbol (READ ONLY)/Protect symbol
Read-only scenes are indicated by an R symbol (READ ONLY) displayed here. Write-
protected scenes are indicated by a Protect symbol.
3 Scene title
Indicates the title of the currently-selected scene.
4 E symbol (EDIT symbol)
This symbol appears when you edit the mix parameters for the currently-loaded scene.
This symbol indicates that you must execute the Store operation if you want to keep the
changes you made.
NOTE
You cannot store data to a scene number for which the Protect symbol or R symbol is displayed.
Storing and recalling scenes
To store the current mix settings as a scene in memory and recall it later, you can use the keys
in the SCENE MEMORY/MONITOR section on the top panel, or you can use the SCENE LIST
window.
Storing a scene
Using the keys of the SCENE MEMORY/MONITOR section
4
3
2 21
STEP
1. Use the pad controls of the top panel or the buttons in the touch screen to set the
mix parameters as desired.
2. Use the SCENE MEMORY [INC]/[DEC] keys to select the store-destination scene
number.
3. Press the SCENE MEMORY [STORE] key.
4. Assign a title or comment to the scene in the SCENE STORE window as desired.
5. Press the SCENE MEMORY [STORE] key or the STORE button located in the lower
part of the SCENE STORE window.
6. Press the OK button in the STORE CONFIRMATION dialog box to execute the Store
operation.
SCENE STORE windowSCENE MEMORY [INC]/[DEC] keys
Scene memory
V5 Reference Manual
96
NOTE
If you press and hold down either of the SCENE MEMORY [INC]/[DEC] keys, the scene number
will increment or decrement continuously.
If you press the SCENE MEMORY [INC] and [DEC] keys simultaneously, the SCENE field
indication will return to the number of the currently-loaded scene.
You can make settings such that the Store Confirmation dialog box will not appear (page 222). In
this case, pressing the SCENE MEMORY [STORE] key once will display the SCENE STORE
window as usual, and pressing it once again will execute the Store operation. Alternatively, you
can rapidly press the SCENE MEMORY [STORE] key twice to store without seeing the SCENE
STORE window.
SCENE STORE window
1 SCENE TITLE field
Press this field to select it, and then enter a title for the scene (maximum 16 characters).
2 COMMENT field
Press this field to select it, and then enter a comment for the scene. You can use this as
a memorandum for each scene (maximum 32 characters).
NOTE
For details on entering text, refer to “Entering names” in the separate Owner’s Manual.
Using the SCENE LIST window
NOTE
You can select multiple scene numbers as the store-destination. To do so, press the MULTI
SELECT button to turn it on, and then rotate a multifunction knob. Alternatively, rotate the
multifunction knob while pressing and holding it down.
If you selected multiple scenes as the store-destination, the same contents will be stored in all
selected scene numbers. This is convenient if you want to create several variations based on the
same mix settings.
You can also use the SCENE MEMORY [INC]/[DEC] keys to select scene numbers.
1 2
STEP
1. Use the controllers on the top panel or the buttons on the touch screen to set the
mix parameters as desired.
2. Press the SCENE field in the Function Access Area.
3. Rotate one of the multifunction knobs to select the store-destination scene number.
4. Press the STORE button in the SCENE LIST window.
5. Assign a title or comment to the scene as desired.
6. Press the STORE button located in the lower part of the SCENE STORE window.
7. Press the OK button in the STORE CONFIRMATION dialog box to execute the Store
operation.
Scene memory
V5 Reference Manual
97
SCENE LIST window
Here you can perform various scene-related operations. This window will appear when you
press the SCENE field.
1 Scene list
This area lists various data about the scenes stored in memory.
2 NO./TITLE buttons
Press these buttons to sort the listed scenes by number or title. Press the same button
repeatedly to toggle between ascending order and descending order.
3 Scene number
Indicates the scene number.
4 Scene title
Indicates the scene title. Press this button to display the SCENE TITLE EDIT window, in
which you can edit the title.
5 R symbol (READ ONLY)/Protect symbol
An “R” symbol is displayed for read-only scenes, and a protect (lock) icon is displayed for
write-protected scenes.
To enable/disable the scene protect setting, press the R symbol or protect symbol of the
selected scene. Pressing the protect (lock) symbol or the R (read-only) symbol
repeatedly will switch between displaying and hiding the corresponding symbol.
Protect (lock) symbol
You will be unable to overwrite the scene.
R (READ ONLY) symbol
Not only will the scene be protected, it will also not be overwritten by any file loaded
from a USB flash drive. You can only apply the protect setting to scenes with consecutive
scene numbers starting with scene #001.
•No symbol
No scene will be protected.
NOTE
The R symbol for scene number 000 cannot be disabled.
6 Current scene
The currently-selected scene (that is, the current scene) is highlighted in blue in the list.
If you press another scene number in the list, the list will scroll and that scene will
become the current scene.
7 SCENE SELECT knob
Use the multifunction knobs to select a scene. You can view the currently-selected scene
number immediately below the SCENE SELECT knob. You can select consecutive
multiple scenes by pressing and rotating the multifunction knob.
8 MULTI SELECT button
You can select consecutive multiple scenes by turning on this button and rotating the
multifunction knob.
9 LAST SCENE button
Selects the scene that was recalled most recently.
0 SCENE STORE button
Press this button to display the SCENE STORE window, which will enable you to assign
a name to a scene and store it.
A STORE UNDO button
Undoes the Store operation. This button is valid only immediately after you perform an
Overwrite-store operation.
NOTE
The STORE UNDO button is available only immediately after overwrite-storing.
You can also assign the function of the STORE UNDO button to a USER DEFINED key
(page 224).
B Page switching tabs
Switch the views for the right side of the SCENE LIST window.
C PREVIEW button
Press this to select PREVIEW mode, which allows you to view and edit the scene settings
in the display and the panel without affecting the signal processing of the current scene.
7
2
3
5
4
8
B9>A
6
C 1
Scene memory
V5 Reference Manual
98
Recalling a scene
Using the keys of the SCENE MEMORY/MONITOR section
Using the SCENE LIST window
SCENE LIST window
1 RECALL SCENE button
Recalls the currently-selected scene.
2 RECALL UNDO button
Undoes the Recall operation. This button is valid only immediately after you perform a
Recall operation.
NOTE
You can also assign the function of the RECALL UNDO button to a USER DEFINED key
(page 224).
You can also use MIDI messages (Program Changes) to recall scenes (page 195).
STEP
1. Use the SCENE MEMORY [INC]/[DEC] keys to select the scene number you want to
recall.
2. Press the SCENE MEMORY [RECALL] key.
3. Press the OK button to execute the recall.
STEP
1. Press the SCENE field in the Function Access Area.
2. Rotate one of the multifunction knobs to select the scene number to recall.
3. Press the RECALL button in the SCENE LIST window.
4. Press the OK button to execute the recall.
12
Scene memory
V5 Reference Manual
99
Using USER DEFINED keys to recall
You can use the USER DEFINED keys to recall a selected scene with a single keystroke, or
to step through the scenes. To do this, you must first assign a scene recall operation to a
USER DEFINED key. The following recall operations can be assigned to a USER DEFINED
key.
INC RECALL
Immediately recalls the scene of the number that follows the currently-loaded scene.
•DEC RECALL
Immediately recalls the scene of the number that precedes the currently-loaded scene.
NOTE
If no scene is stored in the number that precedes or follows the currently-loaded scene, the
closest scene number in which a scene is stored will be recalled.
•DIRECT RECALL
Directly recalls the scene number that you assigned to the USER DEFINED key. When you
press a USER DEFINED key to which this function is assigned, the assigned scene will be
recalled immediately.
STEP
1. In the Function Access Area, press the SETUP button.
2. Press the USER SETUP button in the upper left of the SETUP screen.
3. In the USER SETUP window, press the USER DEFINED KEYS tab.
4. Press the button corresponding to the USER DEFINED key to which you want to
assign a function.
5. In the FUNCTION column, select “SCENE.”
6. Selects the function you want to assign.
To assign INC RECALL or DEC RECALL
Choose “INC RECALL” or “DEC RECALL” in the PARAMETER 1 column.
To assign DIRECT RECALL
Choose “DIRECT RECALL” in the PARAMETER 1 column, and choose “SCENE #xxx” (xxx
is the scene number) in the PARAMETER 2 column.
7. When you have finished making settings, press the OK button to close the window.
8. Press the USER DEFINED key to which you want to assign a recall function.
USER SETUP windowSETUP screen
USER DEFINED KEY SETUP
window
Scene memory
V5 Reference Manual
100
Editing scene memories
This section explains how to sort the scenes stored in scene memory, edit their titles, and
copy and paste them.
Sorting scene memories and editing titles
SCENE LIST window
1 Sort button
The list will be sorted as follows, according to the column heading you press.
•NO.
Sorted in order of scene number.
•TITLE
Sorted in numeric/alphabetical order of title.
COMMENT
Sorted in numeric/alphabetical order of comment.
TIME STAMP
Sorts the list in order of date of creation.
NOTE
By pressing the same location again, you can change the sorting order (ascending or
descending).
2 Write-protect
Indicates the Write Protect on/off status. Press this button to write-protect the scene. A
lock icon will appear. Press it again to cancel write protection.
3 TITLE field
Press this field to open the SCENE TITLE EDIT window, in which you can enter the title
for the scene. You can edit titles in this window.
4 COMMENT field
Press this field to open the SCENE COMMENT EDIT window, in which you can enter
comments for the scene. You can edit comments in this window.
5 STATUS field
Indicators in this field indicate the setting status of the FOCUS, FADE TIME, PLAYBACK
(playback link), and GPI (General Purpose Interface) functions. (The Playback Link
function plays a desired song in a specified time duration after a scene is recalled.)
6 TIME STAMP field
Indicates the date and time the scene was stored.
7 CURRENT SETTING field
Specifies the content that will be saved by the next scene store operation. Changes you
make here are immediately applied to the CL console.
8 Tabs
Enable you to switch between items. You can use tabs to switch the view of the right
half of the window between four different fields (COMMENT/FOCUS/FADE TIME/
PLAYBACK LINK).
STEP
1. Press the SCENE field in the Function Access Area.
2. Press the COMMENT tab at the bottom of the SCENE LIST window.
3. Rotate one of the multifunction knobs on the top panel to select a scene.
4. Edit the scene.
7
8
4
5
6
1 11 2
3
Scene memory
V5 Reference Manual
101
Scene memory editing
The scenes stored in scene memory can be copied and pasted to other scene numbers, or
cleared (erased). You can edit scene memories using the buttons located in the upper part of
the SCENE LIST window.
1 COPY button
Press this button to copy the scene to buffer memory.
2 PAST E bu tton
Press this button to overwrite the selected scene with the scene in buffer memory.
3 CLEAR button
Press this button to erase the selected scene.
4 CUT button
Press this button to delete the selected scene and copy it to buffer memory.
5 INSERT button
Press this button to insert the scene copied to buffer memory into the selected scene
number. The numbers of the subsequent scenes will be incremented by one.
6 UNDO button
Cancels the most recent scene memory paste, clear, cut, or insert operation and restores
the previous state.
Copying and pasting a scene
You can copy a scene into buffer memory, and then paste it to a different scene number.
NOTE
The Global Paste function enables you to copy any channel or any parameter settings for the
current scene, then paste the data into any single or multiple scenes in memory (page 102).
NOTE
Be aware that if you copy or cut another scene before you paste, the newly copied or cut scene
will overwrite the scene in the buffer memory.
You cannot select multiple scenes as the copy-source.
You can select multiple paste-destination scenes. To do so, press the MULTI SELECT button to
turn it on, and then rotate a multifunction knob. Alternatively, rotate the multifunction knob while
pressing and holding it down. In this case, the same content will be pasted to all selected scenes.
A copied scene can also be inserted (page 102).
If nothing has been copied to the buffer memory, the PASTE button will be unavailable.
Clearing a scene
NOTE
You may select multiple scenes to be cleared. To do so, press the MULTI SELECT button to turn
it on, and then rotate a multifunction knob. Alternatively, rotate the multifunction knob while
pressing and holding it down.
Read-only scenes or write-protected scenes cannot be cleared.
1 2 3 4 5 6
STEP
1. Press the SCENE field in the Function Access Area.
2. Rotate one of the multifunction knobs to select the copy-source scene number, and
then press the COPY button in the SCENE LIST window.
3. Press the OK button in the CONFIRMATION dialog box to execute the copy.
4. Rotate one of the multifunction knobs to select the paste-destination scene number,
and then press the PASTE button.
5. Press the OK button in the CONFIRMATION dialog box to execute the paste
operation.
STEP
1. Press the SCENE field in the Function Access Area.
2. Rotate one of the multifunction knobs to select the scene number that you want to
clear, and then press the CLEAR button in the SCENE LIST window.
3. Press the OK button in the CONFIRMATION dialog box to execute the Clear
operation.
Scene memory
V5 Reference Manual
102
Cutting a scene
This section explains how to cut a scene.
When you cut a scene, the numbers of the subsequent scenes will be decremented
accordingly. You can paste or insert a cut scene at the desired location. To cut a scene, sort
the scene list in order of scene number.
NOTE
Read-only scenes or write-protected scenes cannot be cut.
Be aware that if you copy or cut another scene before you paste or insert, the newly copied or
cut scene will overwrite the scene in the buffer memory.
Inserting a scene
You can insert a scene copied to buffer memory at a desired scene number location. To insert
a scene, sort the scene list in order of scene number.
NOTE
If you select multiple scenes as the insert-destination, the same scene will be inserted the
selected number of times.
If nothing has been copied to the buffer memory, the INSERT button is not available.
The INSERT button will also be unavailable if the Insert operation would cause the number of
stored scenes to exceed 300.
When you insert a scene, scenes that were stored in subsequent numbers following that location
will be updated and increase by the number of scenes that were inserted.
Using the Global Paste function
“Global Paste” is a function that lets you copy and paste settings for the desired channel or
parameter from the current scene to scene data in memory (multiple selections are allowed).
This can be convenient if you want to apply changes (that you made to the current scene) to
multiple scenes that have already been stored.
NOTE
The Global Paste function will be available for a user if the SCENE LIST STORE/SORT
parameter is turned on in his or her user level settings.
NOTE
A progress bar will be displayed as the data is being pasted.
During the paste operation, the STOP button will appear. Press the STOP button if you want to
abort the operation. In that case, part of the data will be pasted and you will be unable to undo
the operation.
You cannot select different parameters from different channels.
STEP
1. Press the SCENE field in the SCENE LIST window of the Function Access Area.
2. Rotate one of the multifunction knobs to select the scene number that you want to
cut, and then press the CUT button in the SCENE LIST window.
3. Press the OK button in the CONFIRMATION dialog box to execute the Cut operation.
4. If desired, you can paste (page 101) or insert the cut scene (that was copied to the
buffer memory).
STEP
1. Press the SCENE field in the Function Access Area.
2. Copy (page 101) or cut the scene you want to insert.
3. Rotate one of the multifunction knobs to select the insert-destination scene number,
and then press the INSERT button in the SCENE LIST window.
4. Press the OK button in the CONFIRMATION dialog box to execute the Insert
operation.
STEP
1. Press the SCENE field in the Function Access Area.
2. Press the GLOBAL PASTE button in the SCENE LIST window.
3. Use the tabs in the GLOBAL PASTE window to select the item you want to copy.
4. Press the [SEL] key on the top panel to select the copy-source channel, and then
press the button in the window to select a parameter.
5. Use multifunction knobs 7 and 8 to select the range of paste-destination scenes.
6. Press the PASTE button to execute the paste operation.
GLOBAL PASTE windowSCENE LIST window
Scene memory
V5 Reference Manual
103
GLOBAL PASTE window
1 SET BY SEL button
Turn on this button to add a channel by using the corresponding [SEL] key.
2 CLEAR ALL button/SET ALL button
The CLEAR ALL button clears all of the selected channels. The SET ALL button selects all
channels simultaneously.
NOTE
In the case of the CL3/CL1, faders that do not exist on those models will not be shown.
3 SEND PARAMETER field
Press this field to open the SEND PARAMETER screen. In the SEND PARATMER screen, set
whether to enable global paste for bus selection and send level.
4 Tabs
Enable you to switch between items.
•INPUT tab
Select an input channel in the upper left area, and select its parameter in the lower left
area.
You can select the following parameters.
*1. The parameters for Insert 1 and Insert 2 are selected together.
*2. Settings are linked according to the channel link for the current scene when the settings are made.
OUTPUT tab
Select an output channel in the upper left area, and select its parameter in the lower left
area.
You can select the following parameters.
1
4
2
3
ALL All input channel parameters
INPUT PATCH Input patch settings
NAME Channel name, icon, and channel color
HA Settings for the head amp assigned to the corresponding input channel
DELAY Input delay settings
HPF HPF settings
DIGITAL GAIN Digital gain settings for the corresponding input channel
EQ EQ settings
DYNA 1 Dynamics 1 settings (including KEY IN SOURCE and KEY IN FILTER)
DYNA 2 Dynamics 2 settings (including KEY IN SOURCE)
MIX SEND Send level, pan, and PRE/POST of the signal sent to a MIX bus
MATRIX SEND Send level, pan, and PRE/POST of the signal sent to a MATRIX bus
FADER Fader level
CH ON On/off status of [ON] keys
INSERT
*1
Insert on/off status and insert point
INSERT PATCH
*1
Insert in/out patch settings
DIRECT OUT Direct Out on/off, Direct Out level, Direct Out point and patch settings
MIX ON Send on/off to a MIX bus
MATRIX ON Send on/off to a MATRIX bus
TO STEREO Mode, TO ST/TO LCR on/off status, CSR, pan/balance settings
MONO TO MONO on/off
DCA ASSIGN
*2
Settings registered in DCA group
MUTE ASSIGN
*2
Settings registered in MUTE group
ALL All output channel parameters
OUTPUT PATCH Output patch settings
NAME Channel name, icon, and channel color
EQ EQ settings
Scene memory
V5 Reference Manual
104
*1. The parameters for Insert 1 and Insert 2 are selected together.
*2. Settings are linked according to the channel link for the current scene when the settings are made.
BUS SETUP tab
You can select the following parameters.
•RACK tab
Enables you to choose from GEQ RACK, EFFECT RACK, or PREMIUM RACK. You can
select an individual rack for each effect used in dual mode.
•PATCH/OTHERs tab
You can select the following parameters.
*1. While in PREVIEW mode, changes that are made in CL Editor are not applied immediately. They are applied
after PREVIEW mode is exited.
•DCA tab
You can select ALL, LEVEL/ON, or NAME. If ALL is selected, all channel parameters will
be copied. If LEVEL/ON is selected, the master level and DCA channel on/off status will
be copied. If NAME is selected, the DCA group name will be copied. You can select the
copy-source channels individually for each DCA group 1-16.
For DCA, although you can turn on both the LEVEL/ON button and the NAME button,
they will then both be switched off if you turn on the ALL button.
DYNA 1 Dynamics 1 settings (including KEY IN SOURCE and KEY IN FILTER)
INSERT
*1
Insert on/off status and insert point
INSERT PATCH
*1
Insert in/out patch settings
FADER Fader level
CH ON On/off status of [ON] keys
TO ST/BAL
Mode, TO ST/TO LCR on/off status, CSR, pan/balance settings (MIX 1-24
only)
MONO TO MONO on/off status (MIX 1-24 only)
MATRIX SEND Send level, pan, and PRE/POST of the signal sent to a MATRIX bus
MATRIX ON Send on/off to a MATRIX bus
WITH SEND FROM
SOURCE CHs
SEND parameters of the send-source signal that will be sent to a channel
DCA ASSIGN
*2
Settings registered in DCA group
MUTE ASSIGN
*2
Settings registered in MUTE group
MIX1/2 - 23/24
Sets Recall Safe for MIX 1-24 in the BUS SETUP window. This setting is
applied to a channel pair (one odd-numbered channel and one even-
numbered channel).
MATRIX1/2 - 7/8
Sets Recall Safe for MATRIX 1-8 in the BUS SETUP window. This setting is
applied to a channel pair (one odd-numbered channel and one even-
numbered channel).
SURROUND
SETUP
Surround mode settings.
INPUT PATCH All input channel patches, insert in/out patches, Direct Out patches
OUTPUT PATCH All output channel patches, insert in/out patches
INPUT NAME Channel names, icons, and colors for all input channels
OUTPUT NAME Channel names, icons, and colors for all output channels
HA Analog gain, phantom power on/off status, Gain Compensation settings
CH LINK Channel link settings
MUTE GROUP
NAME
Setting a MUTE group name
CUSTOM FADER
BANK
*1
Custom fader bank settings
CASCADE IN CASCADE IN PATCH and CASCADE IN ATT settings
CASCADE OUT CASCADE OUT PATCH settings
FOCUS Focus function settings
FADE Fade function settings
Scene memory
V5 Reference Manual
105
Using the Focus Recall function
“Focus Recall” is a function that lets you specify the parameters that will be updated when you
recall a scene. For example, it is convenient to use this if you want to recall only the input
channel settings of a certain scene.
NOTE
In contrast to Focus, the CL series console also features a “Recall Safe” function that enables you
to exclude specific channels and parameters from recall operations. However, while the Focus
Recall function is specified individually for each scene, the Recall Safe settings are applied to all
scenes.
NOTE
The FOCUS field enables you to make settings for the Focus function. The buttons in this field
correspond to the scene list shown on the left side of the SCENE LIST window.
Scenes for which Focus settings are made are indicated by a “FOCUS” indication in the STATUS
field of the SCENE LIST window.
You can use the Focus function in conjunction with the Recall Safe function. Channels or
parameters that are excluded from Recall operations by either Focus or Recall Safe will not be
recalled.
For FOCUS RECALL, the NAME parameter is included in the DCA indicator.
FOCUS RECALL window
Sets the parameters that will be recalled.
1 CLEAR ALL button/SET ALL button
Turns off or on all focus channel selections and global focus parameter settings.
2 Focus channel display field
Indicates the target channel for a Recall operation. The view of this field is the same as
that in the RECALL SAFE window.
3 SET BY SEL button
Turn on this button to add a channel by using the corresponding [SEL] key. To add
channels as the target, turn on this button, and then press the corresponding [SEL] keys
for the channels you want to add.
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
STEP
1. Press the SCENE field in the Function Access Area.
2. Press the FOCUS tab at the bottom of the SCENE LIST window.
3. In the SCENE LIST window, press the SET button for the scene you want to set.
4. Follow the procedure starting with step 3 in the “Using the Recall Safe function
(page 82) to make settings.
5. If you want to cancel the specified restrictions so that all parameters will be subject
to recall, turn on the ALL button.
6. Recall a scene for which you have made Focus Recall settings.
SCENE field SCENE LIST window
3
8
6
5
9
1
2
4
7
0
All parameters are affected by Recall on these
Some parameters are affected by Recall on
Recall has been canceled on these channels.
Scene memory
V5 Reference Manual
106
4 FOCUS PARAMETER display field
Indicates the parameters and racks that will be affected by Recall operations for any
scene. Procedures and contents are the same as those in the RECALL SAFE MODE
window (page 83).
5 Channel select button
Selects the channel for which you want to set the Focus Recall function.
NOTE
Switching channels using this button will not affect the channel selection on the top panel.
6 Selected channel display
This area indicates the icon, number, color, and name of the currently-selected channel.
7 APPLY TO ALL INPUT button (input channels only)
Turn on this button to apply the Focus Recall parameter selection for one input channel
to all other input channels.
This can be convenient if you want to apply Focus Recall to the same parameters for all
input channels.
8 Recall parameter select button
Selects Focus Recall parameters for the selected channel.
Enables you to select parameters for each channel that will be affected by Recall
operations. You can use the same procedure as that in the RECALL SAFE window
(page 83).
NOTE
If the DCA ASSIGN button is turned on, the parameters assigned to the DCA groups (1-16) for
that channel are targeted for FOCUS RECALL. Settings for DCA 1-16 are made simultaneously.
DCA ASSIGN button settings are linked according to the channel link for the scene.
9 FOCUS button
Switches the Focus Recall function on or off.
0 CLOSE button
Closes the window.
Using the Fade function
“Fade” is a function that smoothly changes the faders of specified channels and DCA groups
to their new values over a specified duration when you recall a scene. The settings of the Fade
function are made independently for each scene.
NOTE
Scenes for which Fade settings are made are shown by a “FADE” indication in the STATUS field
of the SCENE LIST window.
The Fade function settings can be applied individually even if faders are linked by Channel Link.
You can stop a fade effect by holding down a [SEL] key while you stop the corresponding moving
fader.
If you recall the same scene while faders are moving, the faders of all channels or DCA groups
will move immediately to their target positions.
STEP
1. Press the SCENE field in the Function Access Area.
2. Press the FADE TIME tab at the bottom of the SCENE LIST window.
3. In the SCENE LIST window, press the SET button for the scene you want to set.
4. Press the [SEL] keys for the channels or DCA groups to select the channels or DCA
groups to which the Fade effect will be applied (multiple selections are allowed).
5. Use the multifunction knob to adjust the fade time.
6. Press the OK button to close the FADE TIME window.
7. Press the FADE button in the SCENE LIST window to enable the Fade function.
8. Recall a scene for which the Fade function is turned on.
The faders will begin to move immediately after Recall occurs, and will reach the values
of the recalled scene over the course of the specified fade time.
SCENE LIST window
(FADE TIME field)
SCENE field
Scene memory
V5 Reference Manual
107
SCENE LIST window (FADE TIME field)
1 FADE button
Enables or disables the Fade function for each scene.
2 INDIVIDUAL button
Switches between GLOBAL mode and INDIVIDUAL mode of the Fade function. Set to
on to set the fade time and offset time for each channel. When it is on, PAN can be
individually set on the input channel.
3 SET button
Press this button to open the FADE TIME window, in which you can select a channel for
which you want to use the Fade function, and specify the fade time (the duration of time
over which the fader will reach its new value).
4 FADE TIME display
This area indicates the fade time specified for each scene.
If the INDIVIDUAL mode is set to on, this will not be displayed.
5 CURRENT SETTING field
Specifies the content that will be saved by the next scene store operation. Changes you
make here are immediately applied to the CL console.
FADE TIME window (GLOBAL mode)
You can select the channels to which Fade will be applied, and adjust the fade time. To display
this window, press the SET button in the FADE TIME field in the SCENE LIST window.
1 Channel display field
The channels or DCA groups to which Fade is applied are highlighted. To select the
channels or DCA groups to which Fade is applied, press the [SEL] keys for the channels
or DCA groups. Press the same [SEL] key once again to de-select the channel.
2 FADE TIME knob
Sets the fade time. You can adjust the values by using the multifunction knobs.
The range is 0.0 sec to 60.0 sec.
NOTE
The fade time is used for all channels and DCA groups selected in the channel display field.
3 SET ALL button
Press this button to apply the Fade effect to all faders of that scene.
4 CLEAR ALL button
Press this button to cancel the Fade function for all faders of that scene.
NOTE
In the case of the CL3/CL1, faders that do not exist on those models will not be shown.
1
2
4
5
3
2
34
1
Scene memory
V5 Reference Manual
108
FADE TIME window (INDIVIDUAL mode)
The INDIVIDUAL mode allows you to control fading and fade time of each channel
individually. When the INDIVIDUAL button is set to on, press the SET button in the FADE
TIME field of the SCENE LIST window to open the FADE TIME window.
1 Display switch buttons
Switches the display of the FADE TIME window.
TIME
FADE TIME knob ................... Sets the fade time. You can adjust the value by using
the multifunction knob.
The range is 0.0 sec to 60.0 sec.
START OFFSET
START OFFSET knob............ Sets the offset time from recalling the Scene to starting
the fading. You can adjust the value by using the
multifunction knob.
The range is 0.0 sec to 60.0 sec.
ON
FAD button ............................. Enables or disables the Fade function for each fader.
PAN button ............................. Appears for input channels. Enables or disables the
Fade function for PAN.
2 DEFAULT button
Press this button to restore the default parameter setting.
3 COPY button/PASTE button
Copies/pastes the Fade functions parameters for a channel.
4 Tabs
Use these tabs to select a channel that you want to view on the screen.
31
4
2
Scene memory
V5 Reference Manual
109
Outputting a control signal to an external device
in tandem with scene recall (GPI OUT)
A control signal can be output to an external device connected to the GPI connector of the CL
series console when you recall a specific scene. Proceed as follows.
NOTE
For more information on GPI OUT settings, refer to “Using GPI OUT” (page 272).
SCENE LIST window (GPI OUT field)
1 Output control signal select buttons
These specify the control signal will be output from each GPI OUT.
Pressing a button repeatedly will switch between the following functions.
---- (OFF).................. Nothing will be output.
TRIGGER................. A trigger will be output when the scene is recalled.
TALLY ...................... A tally will be output when the scene is recalled.
2 CURRENT SETTING field
Specifies the content that will be saved by the next scene store operation. Changes you
make here are immediately applied to the CL console.
STEP
1. Press the SCENE field in the Function Access Area.
2. Press the GPI OUT tab at the bottom of the SCENE LIST window.
3. For each scene, specify the control signal that you want to output to each GPI OUT
port.
4. Recall the scene for which you want to output GPI OUT signals.
SCENE LIST window
(GPI OUT field)
2
1
Scene memory
V5 Reference Manual
110
Playing back an audio file that links to a scene
recall
You can also specify an audio file that you want to play back from a USB flash drive when a
specific scene is recalled. This can be convenient if you want an effect sound or BGM to be
played automatically in a specific scene.
NOTE
Save audio files for playback in the SONGS folder within the YPE folder. If you save them in the
root directory or in other folders, you will be unable to specify them for playback. When an audio
file is played, the path in the TITLE LIST screen will indicate \YPE\SONGS\.
You cannot play audio files during recording or in recording standby mode.
A specified audio file will be played back only once, regardless of the playback mode settings.
Audio file names must be eight characters plus three extension characters. If you change the file
name after specifying the file for playback, or if you delete or copy the file repeatedly, the specified
file may become unrecognizable in rare cases.
NOTE
After a scene has been recalled and until the offset time has elapsed, a countdown will appear in
the Function Access Area.
If another song is playing during a scene recall, the song playback will stop when the scene is
recalled, regardless of the offset time setting.
SCENE LIST window (PLAYBACK LINK field)
1 PLAY button
Sets the Playback Link functions on/off status for each scene.
2 Song select button
Press this button to open the SONG SELECT window, in which you can select a song and
set the offset time (time duration from scene recall until the start of playback). Also, the
title of the selected song will appear on the button.
3 Offset time display
Indicates the time duration from scene recall until the start of playback of the specified
audio file. Set the offset time in the SONG SELECT window.
4 CURRENT SETTING field
Specifies the content that will be saved by the next scene store operation. Changes you
make here are immediately applied to the CL console.
STEP
1. Connect a USB flash drive that contains the audio files to the USB connector.
2. Press the SCENE field in the Function Access Area.
3. Press the PLAYBACK LINK tab at the bottom of the SCENE LIST window.
4. Press the song select button for a scene to which you want to link the audio file.
5. Press a list in the SONG SELECT window or use the multifunction knobs to select a
file that you want to link to a scene.
6. Use the corresponding multifunction knob to set the offset (the time duration until
the start of audio file playback).
7. Press the OK button.
8. Press the PLAY button to turn on the link to the audio file.
9. Recall a scene to which an audio file has been linked.
SCENE LIST window
(PLAYBACK LINK field)
4
3
2
1
Scene memory
V5 Reference Manual
111
SONG SELECT window
You can select an audio file you want to link with the scene, and set the offset time. This
window will appear when you press the song select button.
1 Change directory button
Press this button to move to the next higher folder level.
NOTE
You cannot move to levels higher than \YPE\SONGS\.
2 PATH indicator
This area indicates the current directory path. It will show only the \YPE\SONGS\ level.
3 SONG TITLE/FILE NAME switch buttons
Switch between the song title list and the file name list.
4 SONG TITLE list button
5 ARTIST list button
Press these buttons to sort the audio file list (at the current directory level) by song title
and artist name respectively.
6 List
Displays the name of the folder or audio file, artist name, and audio file time duration.
You can select an audio file by pressing the folder name or audio file name.
7 OFFSET knob
You can use the multifunction knob 8 to set the time interval from scene recall until the
start of audio file playback. The offset time can be adjusted in the range of 0.0-99.0 in
0.5 sec steps.
8 Scroll knob
Use the multifunction knob to scroll the list.
7
1
8
2 3
4
5
6
Scene memory
V5 Reference Manual
112
Using Preview mode
Preview mode lets you view or edit the settings of a scene stored in memory without affecting
the signal processing of the current scene. When you recall a scene in this mode, the settings
of the newly recalled scene will appear on the panel of the CL series console, but the signal
processing of the current scene will remain as it was prior to the recall. Even if you modify the
settings and save them as a new scene or by overwriting, the signal processing of the current
scene will remain as it was prior to the recall. During an actual performance, it can be
convenient to use this to check the content of the scene you intend to recall next, or to make
minor changes to a scene and then store it.
NOTE
PREVIEW mode applies to all parameters included in scene memory, all parameters included in
the INPUT PATCH and OUTPUT PATCH functions, and HA parameters.
RECALL SAFE and FOCUS RECALL are enabled in PREVIEW mode.
Functions in Preview mode
The current scene will be modified by the following software and external operations.
CL Editor
StageMix
•MIDI Rx
GPI IN
Similarly, edits for the current scene will be conveyed to the following software and external
devices.
CL Editor
StageMix
•MIDI Tx
•GPI OUT
The meters will indicate the state of signal processing for the current scene.
Playback Link will operate for recalling the current scene.
If cascade-connected, both master and slave units will operate independently. Link will not
occur while in Preview mode.
The following functions will not operate in Preview mode.
Synchronization with CL Editor
Switching users
Changing the User Level
Load/Save functions
Cue changes
USER DEFINED KEY operations
USER DEFINED KNOB operations
Monitor (MONITOR, CUE, OSCILLATOR, TALKBACK) changes or display
Changing or viewing Nuendo Live settings
Changing or viewing the recorder
Changing DANTE SETUP or DANTE PATCH settings
FADE TIME
EFFECT FREEZE playback or recording
MIDI clock and tap tempo for effects
Internal metering for Premium Effects (GR for DynamicEQ and Portico 5043; VU for Opt-
2A, U76 and Buss Comp 369)
In addition, you cannot enter Preview mode while performing the following operations.
While pasting scene or EQ settings
While executing Global Paste
While synchronizing with CL Editor
While saving/loading a file
NOTE
The scene titles shown in StageMix will be changed to the titles used when using the store
operation on a CL series console operated in PREVIEW mode.
STEP
1. Press the [PREVIEW] key. Or, press the PREVIEW button in the SCENE LIST window.
2. Use the [INC]/[DEC] keys, or multifunction knobs in the SCENE MEMORY section to
operate the SCENE SELECT knob in the SCENE LIST window, and select the scene
number that you want to recall.
3. Press the SCENE MEMORY [RECALL] key. Or, press the RECALL SCENE button in the
SCENE LIST window. To execute the Recall operation, press the OK button.
4. If desired, use the panel controls to edit the settings.
5. If you want to store the changes you made in step 4, select the scene number in
which you want to store the scene, and press the SCENE MEMORY [STORE] key. Or,
press the SCENE STORE button in the SCENE LIST window.
6. When you have finished viewing or editing the settings of the scene, press the
PREVIEW key. Or, press the PREVIEW button in the SCENE LIST window.
Monitor and Cue functions
V5 Reference Manual
113
Monitor and Cue functions
The Monitor function lets you monitor various outputs through your nearfield monitors or
headphones. Below the front pad of the CL series console is a PHONES out jack which
always outputs the monitor source signal that you’ve selected for monitoring. By assigning the
MONITOR OUT L/R/C channels to the desired output jacks, you can also monitor the same
signal through external speakers.
You can select the following signals as the monitor source.
STEREO channel output signal
MONO channel output signal
STEREO + MONO channel output signal
OMNI IN 1-2, 3-4, 5-6, 7-8 channel input signal (for monitoring each two channel pair)
RECORDER PLAYBACK output signal
A combination of up to eight MIX, MATRIX, STEREO, or MONO channel output
signals, RECORDER PLAYBACK output signals, and OMNI IN 1-2, 3-4, 5-6, 7-8 input
signals
The Cue function lets you check an individual selected channel/DCA group by temporarily
monitoring it via MONITOR OUT or PHONES. When you press the [CUE] key on the top
panel, the cue signal of the corresponding channel or DCA group is sent as the monitor output
from the selected output port. There is also the Solo function. (Refer to page 125.)
NOTE
The cue signal is sent to the same output destination as the monitor signal. Be aware that for this
reason, the cue signal will no longer be sent to the connected monitor speakers if you turn off the
Monitor function. However, the cue signal will always be sent to the PHONES output jack.
The following diagram shows the cue/monitor signal flow.
MONITOR SELECT
Selects the monitor source.
METER
Detects and indicates the level of the monitor signal or cue signal.
DIMMER
Attenuates the monitor/cue signal by a fixed amount.
CUE(A)
CUE(A)
CUE(A) L
CUE(A) LOGIC
CUE(A)
CUE(A)
CUE(A)
CUE(A) L
CUE(A)
CUE(A) LOGIC
CUE(A)
CUE(A) OUT
LEVEL
CUE(A)
CUE(A) R
CUE(A)
CUE(A) OUT
LEVEL
CUE(A)
CUE(A)
CUE(A) OUT L
CUE(A) OUT R
CUE(A) R
CUE(A)
CUE(A)
CUE(A)
CUE(A) L
CUE(A) R
MAXTRIX OUT
1-6, 7-8(CUE B L,R)
MAXTRIX OUT
1-6, 7-8(CUE B L,R)
CUE(A) L
CUE(A) R
CUE(A) OUT L
CUE(A) OUT R
Monitor and Cue functions
V5 Reference Manual
114
MONITOR LEVEL
Adjusts the output level of the MONITOR OUT L/R/C channels. If PHONES LEVEL LINK
is ON, this setting will also affect the level at the PHONES Out jack.
MONITOR FADER
Use the STEREO MASTER fader or MONO MASTER fader to adjust the output level of the
MONITOR OUT L/R/C channels. MONITOR FADER is positioned in series with
MONITOR LEVEL. If PHONES LEVEL LINK is ON, this setting will also affect the level at
the PHONES Out jack.
ON (On/off)
Switches the Monitor function on or off.
DELAY (Monitor delay)
Delays monitor signals. The Delay function is disabled if cue signals are being output.
PHONES LEVEL (Headphone level)
Adjusts the dedicated output level of the PHONES Out jack.
PHONES LEVEL LINK (Headphone Level Link function)
If this function is turned on, the MONITOR LEVEL knob will adjust the level of signals
sent to the PHONES Out jack.
CUE INTERRUPTION (Cue Interruption function)
If this function is turned on, pressing the [CUE] key on the top panel will cause the cue
signal of the corresponding channel or DCA group to be sent as the monitor output
from the selected output port. With the factory default settings, this function is turned
on.
Turn it off if you do not want to output cue signals to the monitoring speakers.
Using the Monitor function
This section explains how to select the desired monitor source, and monitor it from the
PHONES Out jack or external monitor speakers.
NOTE
Monitor on/off operations, selection of the monitor source, and dimmer on/off operations can also
be assigned to USER DEFINED keys (page 224).
STEP
1. Connect your monitor system to the OMNI OUT jacks or 2TR OUT DIGITAL jack on
the rear panel. To monitor through headphones, connect your headphones to the
PHONES Out jack below the front panel.
2. In the Function Access Area, press the MONITOR button.
3. Press the MONITOR display button or the meter field in the MONITOR screen.
4. Use the source select buttons in MONITOR screen to select the monitor source.
5. Press one of the MONITOR OUT PATCH buttons (L/R/C) in the meter field to specify
the port that will be the output destination for monitor signals L, R, and C (multiple
selections are allowed).
6. Turn the OUTPUT button on to enable monitoring.
7. To adjust the monitor level, use the MONITOR LEVEL knob located in the SCENE
MEMORY/MONITOR section of the top panel.
8. Make settings for Dimmer, Delay, and Monaural as desired.
MONITOR screen
Monitor and Cue functions
V5 Reference Manual
115
MONITOR screen
In the MONITOR screen, the MONITOR field lets you check the current monitor settings, and
turn monitoring on/off.
1 MONITOR display button
When you press this button, the MONITOR window will appear, in which you can make
detailed monitor settings.
2 SOURCE SELECT field
Selects the monitor source. If DEFINE has been selected in this field, access the
MONITOR window to specify the source channel.
3 DIMMER field
Enables you to make settings for the Dimmer function, which temporarily attenuates
monitor signals.
DIMMER LEVEL knob
Adjusts the amount by which the monitor signals will be attenuated when the dimmer
is on.
DIMMER ON button
Turn on this button to enable the dimmer and attenuate the monitor signal.
4 MONITOR FADER field
Enables you to set and view the monitor fader that adjusts the monitor level.
MONITOR FADER LEVEL knob
Adjusts the monitor fader level. Pressing this knob will enable you to use the
multifunction knobs in the Centralogic section to adjust the level.
FADER ASSIGN display
This area displays the type of faders that are currently assigned to the monitor fader.
Indicator assignments are as follows.
---- .......................................... No assignment
MASTER A ............................ Master A only
MASTER A+ .......................... Master A, Master B, Custom fader bank
MASTER B ............................ Master B only
MASTER B+ .......................... Master B, Custom fader bank
CUSTOM................................ A single fader in the Custom fader bank
CUSTOMs.............................. Multiple faders in the Custom fader bank
5 Meter field
Indicates the output level of Monitor Out channels L, R, and C. Press this field to open
the MONITOR window.
6 MONITOR OUTPUT button
Switches Monitor Out on or off.
7 PHONES LEVEL LINK button
If this is on, the MONITOR FADER LEVEL knob will adjust the level of signals sent to the
PHONES Out jack.
8 MONO MONITOR button
Turn on this button to switch monitor signals to mono.
1
6
7
8
2 3 4 5
Monitor and Cue functions
V5 Reference Manual
116
MONITOR window
You can make detailed settings for monitoring. This window appears when you press the
MONITOR display button or meter field in the MONITOR screen.
SOURCE SELECT field
This field enables you to select the source signal for the MONITOR bus.
1 Source selection buttons
Select one of the following as the signal source that will be output to the MONITOR bus.
DIMMER field
This field enables you to make settings for the Dimmer function, which temporarily attenuates
monitor signals.
2 DIMMER knob
Adjusts the amount by which monitor signals will be attenuated when the Dimmer
function is on.
3 DIMMER ON/OFF button
Switches the Dimmer function on or off.
4 TALKBACK DIMMER knob
Adjusts the amount by which the monitor level will be attenuated when talkback is on.
5 TALKBACK ON indicator
Indicates the talkback on/off status.
6 PHONES LEVEL LINK button
Enables you to link the signal level at the PHONES Out jack to the monitor signal level.
Turn on this button to adjust the level of signals sent to the PHONES Out jack by using
the MONITOR FADER LEVEL knob
0 or the fader A to which this knob function has
been assigned.
NOTE
If the PHONES LEVEL LINK button is ON, use the MONITOR LEVEL knob and the monitor fader,
as well as the PHONES LEVEL knob to adjust the monitor level when monitoring through
headphones.
7 CUE INTERRUPTION button
Press this button to interrupt the monitor signal by the cue signal. If this button is on
and the cue is enabled, the cue signal will be sent to the monitor output. With the
factory default settings, this function is turned on. If you do not wish to send the cue
signal to the monitor output, switch this button off.
8 MONO MONITOR button
Turn on this button to switch the monitor output signal to mono.
9 MONITOR OUTPUT button
This button turns the monitor output on/off. When this button is turned on, the monitor
source selected in
1 is sent to output destination E.
NOTE
The PHONES output jack will always output the monitor signal, regardless of whether the
OUTPUT button is on or off.
STEREO L/R STEREO L/R channel signals
MONO (C) MONO channel signal
LCR STEREO L/R + MONO channel signals
OMNI 1-2 - 7-8 OMNI IN jacks 1 - 8 signals (per two channels)
PB OUT Recorder’s PLAYBACK OUT signals
DEFINE The signal(s) selected in the ASSIGN field
9
D
E
F
1
24 7
3
B
6 8
5 A0C
Monitor and Cue functions
V5 Reference Manual
117
MONITOR FADER field
0
MONITOR FADER LEVEL knob
Indicates the monitor level. Press this knob to adjust the monitor level using the
multifunction knob. Or, press the Centralogic section bank select [STEREO] key, and
then use the monitor fader to adjust the level.
A FADER ASSIGN indicator
Indicates the fader(s) to which the monitor level is assigned. Indicator assignments are
as follows:
MONITOR DELAY field
This field enables you to specify the monitor delay setting by which the monitor out signal is
delayed.
B AUTO BYPASS button
Turn this on to automatically bypass monitor delay when the cue is on.
C MONITOR DELAY knob
Indicates the currently-specified delay time. The millisecond value is indicated above the
knob, and the delay time value in currently-selected units and the currently-selected
scale type are indicated below the knob. However, if the scale is set to ms, the delay time
value is not shown above the knob.
Press this knob to control the level using the multifunction knobs.
Meter field
Indicates the monitor output level.
D Meters
This field indicates the output level of the monitor L/R/C channels.
E MONITOR OUT PATCH button
Press this button to open the PORT SELECT window, in which you can select an output
port to patch to the monitor out L/R/C channels.
NOTE
You can specify output ports only for MONITOR OUT L and R, and monitor through two speakers.
If you have not specified an output port for MONITOR OUT C, selecting the MONO (C) button or
LCR button as the monitor source will automatically cause the MONO channel signal to be
distributed to MONITOR OUT L/R.
F ASSIGN field
If you have selected DEFINE in the SOURCE SELECT field, you can use the ASSIGN field
to specify multiple monitor sources. The following table shows the monitor sources that
you can select in the ASSIGN field.
NOTE
You can select a maximum of eight monitor sources in the ASSIGN field. If you select eight
monitor sources, no further selections will be possible. Turn off the buttons of unneeded sources.
MASTER A MASTER A fader only
MASTER A+ MASTER A, as well as MASTER B fader and Custom fader bank
MASTER B MASTER B fader only
MASTER B+ MASTER B, as well as Custom fader bank
CUSTOM One of the Custom fader bank faders
CUSTOMs Multiple Custom fader bank faders
DANTE 1-64 Output channels 1-64 to audio network
OMNI1-8 OMNI OUT jacks 1-8
DIGI OUT L/R DIGITAL OUT jack on the CL unit
SLOT1-1 - SLOT3-16 Output channels 1-16 of an I/O card installed in slots 1-3
MIX 1-24 Output signals of MIX channels 1-24
MTRX 1-8 MATRIX buses 1 - 8 output signals
STEREO STEREO L/R channel output signals
MONO (C) MONO channel output signal
OMNI 1-2 - OMNI 7-8
OMNI IN jacks 1 - 8 input signals (per two
channels)
PB OUT Recorder’s PLAYBACK OUT signals
Monitor and Cue functions
V5 Reference Manual
118
MONITOR screen (Monitor field in Surround mode)
If you set a bus to Surround mode in BUS SETUP, the Monitor field in the MONITOR screen
appears as shown below.
1 SURROUND MONITOR display button
When you press this button, the SURROUND MONITOR window will appear, in which
you can make detailed surround monitor settings.
2 SOURCE SELECT field
Selects the surround monitor source. If 2CH MONITOR has been selected in this field,
use the SURROUND MONITOR window to specify the source channel.
3 Speaker Mute field
You can individually mute each speaker that is monitored.
4 DOWNMIX field
Select in which field to perform downmixes.
•STEREO button
Downmix in stereo mode.
MONO button
Downmix in mono mode.
5 Meter field
Shows the meters for the surround signal being monitored. The layout of the meters is
the same as the layout set in the SURROUND SETUP screen.
SURROUND MONITOR window (Surround mode)
You can make detailed settings for surround monitoring. If Surround mode is set for the bus
settings in BUS SETUP, this window appears when you press the MONITOR display button
or meter field in the MONITOR screen.
1 SOURCE SELECT field
Select one of the following as the surround source that will be output to the MONITOR
bus.
2 MONITOR SOURCE SETUP button
Use this button to open the MONITOR SOURCE SETUP screen. Set the sources and
names for EXT 5.1 - 1-3 (EXTERNAL SURROUND) and EXT ST - 1-4 (EXTERNAL STEREO).
1
2 3 54
MIX1-6 Surround signals in the current mix
EXT5.1-1-3 Surround signals set in MONITOR SOURCE SETUP (3 channels)
2CH MONITOR Stereo signals set in MONITOR SOURCE SETUP
7
6
5
1
342
Monitor and Cue functions
V5 Reference Manual
119
3 DOWNMIX field
Select in which field to perform downmixes.
•STEREO button
Downmix in stereo mode.
MONO button
Downmix in mono mode.
4 DOWNMIX SETUP button
Use this button to open the DOWNMIX SETUP screen. Set the parameters for
downmixes.
5 Meter field
Shows the meters for the surround signal being monitored. The layout of the meters is
the same as the layout set in the SURROUND SETUP screen.
6 Speaker Mute field
You can individually mute each speaker that is monitored.
7 SOLO button
Turns on the solo function for the monitor speakers. When turned on, all speaker
buttons in the speaker mute field are turned on. At this time, if you press one of the
speaker buttons, only that button remains on; the other buttons go off. If you press a
different speaker button, the other buttons go off.
NOTE
If you switch to Surround mode, the patch for monitor output can be set in the OUTPUT PORT
screen rather than this screen. (Refer to page 63.)
MONITOR SOURCE SETUP screen
Press the MONITOR SOURCE SETUP button in the SURROUND MONITOR screen to open
this screen.
1 NAME field
Press this button to open the PATCH/NAME screen (with the NAME tab selected). Enter
the source name in the Keyboard screen.
2 PATCH field
Press this button to open the PATCH/NAME screen (with the PATCH tab selected). Select
the port to patch.
21
1
Monitor and Cue functions
V5 Reference Manual
120
DOWNMIX SETUP screen
Press the DOWNMIX SETUP button in the SURROUND MONITOR screen to open this
screen. The layout of the channels is the same as the layout set in the SURROUND SETUP
screen.
1 Output channel field
Selects the output channel. You can use the L and R buttons to switch each between on/
off.
2 Downmix parameter field
Sets the downmix parameters for each channel and the master channel monitors.
3 APPLY TO MIX1-6 TO STEREO button
Press this button to apply the downmix parameters for the set monitors to the downmix
parameters for the main channel (MIX1-6 to STEREO).
Using the Cue function
About Cue groups
Cue signals on the CL series console can be categorized into the following four groups.
1 INPUT CUE group
The cue signals of input channels make up this group. To enable Cue for this group,
press the [CUE] key for any input channel to turn Cue on.
NOTE
If input channels or ST IN channels are assigned to the Centralogic section, you can also use the
[CUE] keys in the Centralogic section to enable Cue for this group.
2 DCA CUE group
The cue signals of DCA groups make up this group. To enable Cue for this group, assign
the DCA groups to the Centralogic section and press a [CUE] key in the Centralogic
section to turn Cue on.
3
2
1
Input channel [CUE] key
[CUE] key in the Centralogic section
(When using DCA groups)
Monitor and Cue functions
V5 Reference Manual
121
3 OUTPUT CUE group
The cue signals of output channels make up this group. To switch Cue on or off for this
group, press the [CUE] key in the Master section, or assign MIX channels or MATRIX
channels to the Centralogic section and press a [CUE] key in the Centralogic section.
NOTE
If STEREO/MONO channels are assigned to the Centralogic section, you can also use the [CUE]
keys in the Centralogic section to enable Cue for this group.
4 Other CUE group
These cue signals are operated via buttons displayed on the
touch screen. This group is enabled if you turn on the CUE
button in the EFFECT window or the PREMIUM window, or
if you turn on the KEY IN CUE button in the DYNAMICS 1
window. This group will automatically be disabled when
you exit the corresponding window.
NOTE
You cannot turn on cue monitoring between different groups simultaneously. Normally, the group
to which the most recently-pressed [CUE] key (or on-screen CUE/KEY IN CUE button) belongs
will take priority, and the [CUE] keys for the previously-selected group will be defeated.
However, if you switch the Cue signal group in a specific order, the state of the [CUE] keys of the
previously-selected group will be restored when the current Cue signal is defeated.
The following illustration shows the
priority order of the [CUE] keys. After
you have switched groups from lower
to upper levels, if you then defeat cue
for the upper group, the previous
[CUE] key status of the group
immediately below will be restored.
For example, if you switch groups in
the order of OUTPUT CUE group
DCA CUE group INPUT CUE group
Other CUE group, you can then
successively defeat the [CUE] keys
(CUE/KEY IN CUE buttons) to
successively restore the [CUE] key
status of the previously-selected group.
[CUE] key in the Master section
[CUE] key in the Centralogic section
(When operating the MIX channel or
MATRIX channel)
On-screen CUE button
Other CUE group
INPUT CUE group
DCA CUE group
OUTPUT CUE group
Monitor and Cue functions
V5 Reference Manual
122
Operating the Cue function
This section explains how to use the [CUE] key for a channel or DCA group to monitor cue
signals.
NOTE
The cue signal is sent to the same output destination as the monitor signal. Be aware that for this
reason, the cue signal will not be sent to the connected monitor speakers if you turn off the
Monitor function. However, the PHONES Out jack below the front pad will always output cue
signals regardless of the Monitor on/off setting. See “Using the Monitor function” (page 114) for
details about the Monitor function.
NOTE
The cue signal is sent to the monitor output and PHONES Out jacks regardless of whether the
CUE OUTPUT button is on or off. However, the cue signal will no longer be sent to monitor output
if CUE INTERRUPTION is turned off. The cue signal is always sent to the PHONES Out jack,
regardless of the CUE INTERRUPTION setting.
When using the MIX/MATRIX bus select buttons in the SENDS ON FADER window, you can
press the selected button once again to turn on Cue for the corresponding MIX/MATRIX channel
(page 46).
If you want cue operations and channel select operations to be linked, open the USER SETUP
window, choose the PREFERENCE tab, and then turn on [CUE] [SEL] LINK (page 223).
You can also assign the function of the CLEAR CUE button to a USER DEFINED key (page 224).
If PHONES LEVEL LINK (page 115) in the MONITOR screen is ON, the cue signal level when
monitoring through headphones can be adjusted using both the MONITOR LEVEL knob and the
PHONES LEVEL knob.
To adjust the level to the output destination port for the cue signal, adjust the gain of the output
port that is patched to it.
If you turn on the [CUE] key or the CUE button on the display, the CUE meter is displayed in the
Function Access Area, indicating the CUE output level. The upper part of the cue meter shows
an abbreviation indicating the currently-on cue group or cue button. The abbreviations displayed
for the cue meters have the following meaning.
STEP
1. In the Function Access Area, press the MONITOR button.
2. Press the CUE display button or the INPUT/DCA/OUTPUT CUE field in the MONITOR
screen.
3. Use the CUE MODE button in the CUE screen to specify what will happen when
multiple [CUE] keys within the same CUE group are turned on.
4. Use the buttons and knobs of the INPUT CUE/DCA CUE/OUTPUT CUE field to specify
the output position and output level for each CUE group.
5. Press one of the CUE OUT PATCH buttons (L/R) in the meter field to specify a port
as the output destination for cue signals L and R (multiple selections are allowed).
6. Press the [CUE] key of the channel or DCA group to be monitored to turn it on.
7. Adjust the Cue signal level by using the [MONITOR LEVEL] knob located in the
SCENE MEMORY/MONITOR section of the top panel.
8. To defeat cue, press the currently-on [CUE] key once again. To clear all cue
selections, press the CLEAR CUE button in the Meter field.
MONITOR screen
IN INPUT CUE group
DCA DCA CUE group
OUT OUTPUT CUE group
EFFECT
CUE button in the EFFECT and PREMIUM RACK windows
(Other CUE groups)
KEY IN
KEY IN CUE button in the DYNAMICS1 window
(Other CUE groups)
REC/PB
RECORDER INPUT CUE button or PLAYBACK OUT CUE button
(Other CUE groups)
CUE meter
Monitor and Cue functions
V5 Reference Manual
123
If CUE is set to 2 channels, the CUE meter is displayed as shown below.
MONITOR screen
The CUE field of the MONITOR screen lets you check the current Cue settings, and turn Cue
on/off.
1 CUE display button
When you press this button, the CUE window will appear, in which you can make
detailed cue settings.
2 CUE MODE buttons
Select the cue mode. You can select MIX CUE mode (all selected channels will be cued),
or LAST CUE mode (only the channel selected most recently will be cued).
3 INPUT/DCA/OUTPUT CUE section
Indicates the settings for input cue, DCA cue, and output cue. Press this field to open
the CUE window.
4 CUE OUTPUT button
Switches the cue output on or off.
5 CLEAR CUE button
Cancels all cue selections simultaneously. If MIX CUE mode has been selected, all of the
selected channels will be cleared.
CUE A&B
Only CUE A
Only CUE B
1
4
5
2 3
Monitor and Cue functions
V5 Reference Manual
124
CUE window
You can make detailed settings for the cue. This window will appear when you press the
INPUT/DCA/OUTPUT CUE field.
1 CUE MODE buttons
Select one of the following two cue modes:
MIX CUE
All selected channels will be mixed and monitored.
•LAST CUE
Only most recently selected channel will be monitored.
NOTE
All cue selections will be cleared if you switch between MIX CUE mode and LAST CUE mode in
the CUE MODE section.
INPUT CUE field
This field enables you to make settings related to the input channel cue.
2 Cue point select button
Sets the cue point to PFL (immediately before fader), AFL (immediately after fader), or
POST PAN (immediately after PAN).
NOTE
Be aware that if you turn on the POST PAN button, you will be unable to monitor signals sent to
the MONO bus from an input channel in LCR mode.
3 PFL TRIM knob
Indicates the monitor levels when PFL is selected. You can adjust the level using the
multifunction knob.
You can adjust the monitor levels in the range of -30dB to +20dB.
DCA CUE field
This section enables you to make settings related to DCA cue.
4 Cue point select button
Sets the cue point for the DCA group to PRE PAN (immediately before PAN) or POST
PAN (immediately after PAN).
5 DCA TRIM knob
Indicates the monitor level of cue signals from a DCA group. You can adjust the level
using the multifunction knob.
You can adjust the monitor levels in the range of -30dB to +20dB.
6 UNITY button
Turn on this button to monitor signals at the same volume level that was obtained when
the master level for each DCA group was set to 0 dB (unity gain).
OUTPUT CUE field
This section enables you to make settings related to output channel cue.
7 Cue point select button
Sets the cue point for the output channel to PFL (immediately before fader) or AFL
(immediately after fader).
8 PFL TRIM knob
Indicates the monitor levels when PFL is selected. You can adjust the level using the
multifunction knob.
You can adjust the monitor levels in the range of -30dB to +20dB.
Meter field
9
ACTIVE CUE indicator
Lights to indicate the type of cue currently being monitored (input: blue, DCA: yellow,
output: orange).
0 CLEAR CUE button
Cancels all cue selections simultaneously.
NOTE
If you press the CUE meter in the Function Access Area, all cue selections will be cleared.
A Meter section
This field indicates the output level of the cue L/R channels.
F
E
G
I
BA74
D >965 8
12
3
C
H
Monitor and Cue functions
V5 Reference Manual
125
B CUE OUTPUT button
Switches the cue output on or off.
C CUE LEVEL knob
Indicates the output level of the cut out. You can adjust the values by using the
multifunction knobs.
D CUE OUT PATCH button
Press this button to open the PORT SELECT window, in which you can select an output
port to patch to the cue out L/R channels.
FADER CUE RELEASE field
Move the fader of the channel that is cued to set the FADER CUE RELEASE function for
releasing the cue.
E ON button
Switches the FADER CUE RELEASE function on or off.
F THRESHOLD knob
Sets the fader value for releasing the cue. If the fader value exceeds the value set with
this knob, the cue is released.
SOLO field
Determines the Solo function parameters.
With the Solo function, only the signal of the input/output channel or DCA for which the [CUE]
key is pressed is output from MIX, MATRIX, and STEREO on each bus. All other channels or
DCA are muted.
G SOLO SAFE popup button
When the SOLO SAFE popup button is pressed, the SOLO SAFE popup window (which
specifies soloed channels that are not muted) appears.
Here you can specify the channels that will be excluded from Solo operations. (You can
specify more than one.) The channels that are selected here will not be muted when
SOLO mode is enabled. This function is convenient if, for example, you want to protect
certain channels from being set to SOLO mode accidentally, such as the main STEREO
channels and MIX channels that send signals to an external recorder.
DANTE 1-64 Output channels 1-64 to audio network
OMNI1-8 OMNI OUT jacks 1-8
DIGI OUT L/R DIGITAL OUT jack on the CL unit
SLOT1-1 - SLOT3-16 Output channels 1-16 of an I/O card installed in slots 1-3
Monitor and Cue functions
V5 Reference Manual
126
H SOLO ON button
Turns Solo operation on or off. A popup window will ask you to confirm Solo operation.
To execute Solo operation, press the OK button. The button will light up and SOLO
mode will be enabled. To use the Solo function, make sure this button is on, and then
turn on the [CUE] key of the desired channel or DCA. Only the corresponding channel
or DCA will be output to the buses and output jacks;
the remaining channels and DCA groups will be muted. The same signal will also be
output from the CUE OUT jacks and the MONITOR OUT jacks.
When you press this button, the MONITOR button in the Function Access Area will flash
as shown.
NOTE
If you turn on the [CUE] key of an output channel, the signal will be sent only to the corresponding
bus.
To defeat Solo, press the currently-on SOLO ON button once again.
NOTE
If you press [LAST CUE] to switch the CUE MODE from LAST to MIX (or vice versa), all
previously-enabled Cue (Solo) signals will be defeated.
CUE B field
I
USE MATRIX 7/8 AS CUE B button
When this button is pressed, channels 7 and 8 on the MATRIX bus are combined and
used as a two-channel CUE.
CUE screen (When configuring CUE B)
When the USE MATRIX 7/8 AS CUE B button is pressed, a confirmation popup window
appears. If you press the OK button, the screen expands so you can configure the CUE A/B
settings.
1 USE MATRIX 7/8 AS CUE B button
When this button is pressed to turn it off, the CUE will be only a single channel.
CUE A field
Configures the settings for CUE A.
If the CH/REMOTE switch button (
2) is set to “CH”, switching of the CUE MODE button will
be linked with CUE A/B.
In Surround mode, a 5.1 SOLO button is added to the CUE MODE field.
2
1
3
CUE A field
CUE OPERATION
MODE field
CUE B field
Monitor and Cue functions
V5 Reference Manual
127
CUE B field
Configures the settings for CUE B.
If the CH/REMOTE switch button (
2) is set to “CH”, switching of the CUE MODE button will
be linked with CUE A/B.
CUE OPERATION MODE field
2
CH/REMOTE switch buttons
This section explains how to use a two-channel CUE.
For example, when a single operator wants to use two separate CUEs, they can be set
separately to an in-ear monitor signal and a floor monitor signal. If a single operator
wants to use a two-channel CUE, select the “CH.” Select the desired CUE SETTINGS for
each channel. You can select from A, B, or A+B. To use one CUE each for the console
and CL Editor/StageMix, select the “REMOTE.” The console is fixed to CUE A, while the
CL Editor/StageMix is fixed to CUE B.
NOTE
When “REMOTE” is selected, the device where CUE is actually turned on and the corresponding
targets are shown in the table below.
3 CUE SETTINGS button
Use this button to open the CUE SETTINGS screen.
1 CUE A ALL button
Press this button to set all channels displayed in the screen to CUE A only. However, if
the selected tab is INPUT, all input channels are set to CUE A only.
2 CUE B ALL button
Press this button to set all channels displayed in the screen to CUE B only. However, if
the selected tab is INPUT, all input channels are set to CUE B only.
3 A/B switch button
Use this button to switch A and B on/off. However, both cannot be turned off at the
same time.
4 Tab
Use these to select the desired edit operation.
NOTE
If the ALTERNATE function is assigned to a USER DEFINED key and the [CUE] key is pressed
while ALTERNATE is on, the channel settings will toggle between A
B A+B each time the
key is pressed.
Device Target
Console CUE A
Cascaded console CUE A
MIDI CUE B
CL Editor CUE B
StageMix CUE B
GPI CUE A
1
4
3
2
Monitor and Cue functions
V5 Reference Manual
128
MONITOR screen (When using CUE B)
When CUE B is enabled by setting, the CUE field in the MONITOR screen appears as shown
below.
In Surround mode, the CUE field appears as shown below.
MONITOR screen (CUE field in Surround mode)
If you set a bus to Surround mode in BUS SETUP, the CUE field in the MONITOR screen
appears as shown below.
1 5.1. SOLO Button
Used to cue only the input channels to be used in the 5.1 channel mix. Outputs,
PLAYBACK OUT, and EFFECT cannot be cued.
CUE screen (Surround mode)
If you set a bus to Surround mode in BUS SETUP, the CUE screen (where you can make
detailed cue settings) appears as shown below.
1 5.1. SOLO Button
5.1 SOLO is only for input channels. Outputs, PLAYBACK OUT, and EFFECT cannot be
cued.
1
1
Talkback and Oscillator
V5 Reference Manual
129
Talkback and Oscillator
Talkback is a function that sends the signal of a mic connected to the TALKBACK jack to the
desired bus. This is used mainly to convey instructions from the operator or sound engineer
to the performers and staff. If necessary, you can also use a mic connected to an INPUT jack
on the I/O device or the OMNI IN jack on the CL unit for talkback.
CL series consoles also feature an oscillator that can output a sine wave or pink noise to the
desired bus, so that you will be able to check external equipment or to test the acoustical
response of the room or hall.
The diagram below shows the signal flow of the talkback and oscillator signals.
Using Talkback
The Talkback function sends the signal (that is input at the input jacks) to the desired bus.
NOTE
The PAD will be switched on or off internally when the HA gain is adjusted between +17 dB and
+18 dB.
Keep in mind that noise may be generated if there is a difference between the Hot and Cold
output impedance of the external device connected to the INPUT connector when using phantom
power.
You can also assign talkback on/off or an ASSIGN change to a USER DEFINED key. In this case,
you can select either a Latch operation or an Unlatch operation (the function will be enabled only
while you continue holding down the key) (page 224).
When talkback is on, you can use the talkback dimmer to lower the monitor levels other than the
talkback signal (page 116).
CUE(A)
MATRIX
(USE 7-8
AS CUE B)
STEP
1. In the Function Access Area, press the MONITOR button.
2. Press the TALKBACK display button or the ASSIGN field in the MONITOR screen.
3. Connect a mic to the front panel TALKBACK jack, and turn the TALKBACK GAIN knob
to adjust the input sensitivity of the mic.
4. Press a button in the ASSIGN field in the TALKBACK window to specify the bus(es)
to which the talkback signal will be sent (multiple selections are allowed).
5. To enable talkback, press the TALKBACK ON button to turn it on.
MONITOR screen
Talkback and Oscillator
V5 Reference Manual
130
MONITOR screen
In the MONITOR screen, the TALKBACK field enables you to check the current talkback
settings, and turn talkback on or off.
1 TALKBACK display buttons
When you press this button, the TALKBACK screen will appear, in which you can make
detailed talkback settings.
2 TALKBACK IN field
+48V indicator ........................ Indicates the on/off status of the +48V phantom power
supplied to the TALKBACK jack.
Input level meter................... Indicates the level of signals after the input gain at the
TA L KBACK jac k .
3 INPUT TO TALKBACK field
INPUT TO TALKBACK patch button
........................ Press the button to open the PORT SELECT window, in
which you can patch a desired input port to talkback.
The selected port name will appear on the button.
INPUT GAIN knob................. Sets the input gain of the selected port.
Input level meter................... Indicates the level of signals after the input gain.
4 TALKBACK ASSIGN field
An indicator lights to indicate the currently-selected output destination of the talkback
signal.
5 TALKBACK ON button
Switches talkback on or off.
TALKBACK window
You can make detailed settings for talkback. This window appears when you press the
TALKBACK display button in the MONITOR screen.
TALKBACK IN field
This field enables you to make settings for the TALKBACK jack on the front panel.
1 +48V button
Switches on or off the phantom power (+48V) supplied to the TALKBACK jack.
2 TALKBACK level meter
This indicates the input level of the mic connected to the TALKBACK jack.
INPUT TO TALKBACK field
This field enables you to route a signal from a mic (connected to a normal input jack) to
talkback. If you want to use an input jack other than the TALKBACK jack as supplementary
input for talkback, select an input port here and set the input level.
3 INPUT TO TALKBACK patch button
Press this button to open the PORT SELECT window, in which you can select an input
port.
1 2 3 4 5
1
2
3 4 6 8 975
0
A
Talkback and Oscillator
V5 Reference Manual
131
4 +48V button
This is an on/off switch for the phantom power (+48V) supplied to the selected input
port.
NOTE
This button will not appear if no input port is selected.
5 ANALOG GAIN knob
Indicates the analog gain value for the selected input port. Press this knob to control the
level using the multifunction knobs.
6 HA level meter
Indicates the input level of a mic connected to the selected input port.
7 GC button
Turns the Gain Compensation (gain correction function) on or off. The button will
appear if the input jack of an I/O device is patched.
8 Gain compensation level meter
Indicates the level after gain compensation. This will appear if the input jack of an I/O
device is patched.
9 TALKBACK ON/OFF button
This switches talkback on/off. While talkback is on, the signal from the INPUT jack
selected as the TALKBACK jack will be output to the send-destination bus.
ASSIGN field
0
Channel select buttons
These buttons enable you to select a channel on which the talkback signal is sent.
A CLEAR ALL button
Press this button to clear all selections.
Using the Oscillator function
You can send a sine wave or pink noise from the internal oscillator to the desired bus.
STEP
1. In the Function Access Area, press the MONITOR button.
2. Press the OSCILLATOR display button or the ASSIGN field in the MONITOR screen.
3. Press a button in the OSCILLATOR MODE field in the OSCILLATOR window to select
the type of signal you want to output.
4. Use the knobs and buttons in the parameter field to adjust the oscillator parameters.
5. Press a button in the ASSIGN field to specify the input channel(s) or bus(es) to which
the oscillator signal will be sent (multiple selections are allowed).
6. Press the OUTPUT button to enable the oscillator.
MONITOR screen
Talkback and Oscillator
V5 Reference Manual
132
MONITOR screen
In the MONITOR screen, the OSCILLATOR field lets you check the current oscillator settings,
and turn the oscillator on or off.
1 OSCILLATOR display button
When you press this button, the OSCILLATOR screen will appear, in which you can make
detailed oscillator settings.
2 OSCILLATOR LEVEL field
Indicates the frequency and level of the currently-selected oscillator. A meter in this field
indicates the output level of the oscillator. Press the LEVEL knob to adjust the oscillator
level using the multifunction knob.
3 OSCILLATOR MODE field
Indicates the currently-selected oscillator mode. Pressing the MODE button repeatedly
will switch modes.
4 OSCILLATOR ASSIGN field
An indicator lights to indicate the currently-selected oscillator output destination (input
channels or buses). Use the tabs on the left to select channels or buses to display.
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
5 OSCILLATOR OUTPUT button
Turns the oscillator output on or off.
OSCILLATOR window
You can make detailed settings for the oscillator. This window appears when you press the
OSCILLATOR display button in the MONITOR screen.
1 OSCILLATOR MODE buttons
Select one of the following four operating modes when the oscillator is turned on:
2 Parameter field
Enables you to set the oscillator parameters. The controllers and their functions in this
field vary depending on the selected mode.
Mode = SINE WAVE
LEVEL knob..........Indicates the output level of the sine wave. You can adjust the
value by using the multifunction knob.
FREQ knob ...........Indicates the frequency of the sine wave. You can adjust the value
by using the multifunction knob.
1
3
2
54
SINE WAVE A sine wave will be output continuously.
SINE WAVE 2CH
Two sine waves of different frequencies will be output
separately.
PINK NOISE Pink noise will be output continuously.
BURST NOISE Pink noise will be output intermittently.
21
5
4
3
Talkback and Oscillator
V5 Reference Manual
133
Mode = SINE WAVE 2CH
LEVEL knob (ODD/L) ........ Indicates the output level of the sine wave on the ODD/L
side. You can adjust the value by using the multifunction
knob.
FREQ knob (ODD/L) .......... Indicates the frequency of the sine wave on the ODD/L
side. You can adjust the value by using the multifunction
knob.
LEVEL knob (EVEN/R) ...... Indicates the output level of the sine wave on the EVEN/
R side. You can adjust the value by using the
multifunction knob.
FREQ knob (EVEN/R)........ Indicates the frequency of the sine wave on the EVEN/R
side. You can adjust the value by using the multifunction
knob.
By default, ODD(L) is set to 1kHz and EVEN(R) is set to 400Hz. At this time, there are
two meters (L and R).
Mode = PINK NOISE
LEVEL knob ..........Indicates the output level of the pink noise. You can adjust the
value by using the multifunction knob.
HPF knob ..............Indicates the cutoff frequency of the HPF that processes pink
noise. You can adjust the value by using the multifunction knob.
Use the button below the knob to switch the HPF on or off.
LPF knob...............Indicates the cutoff frequency of the LPF that processes pink
noise. You can adjust the value by using the multifunction knob.
Use the button below the knob to switch the LPF on or off.
Mode = BURST NOISE
LEVEL knob, HPF knob, and LPF knob
....................Same as in PINK NOISE mode.
WIDTH ...................Indicates the length of noise being output intermittently. You can
adjust the value by using the multifunction knob.
INTERVAL .............Indicates the length of silence between noise bursts. You can
adjust the value by using the multifunction knob.
3 ASSIGN section
Enables you to select a channel to which the oscillator signal will be sent. Press one of
the three tabs below to select the type of channels displayed, and then press the
button(s) for the desired channel(s) (multiple selections are allowed). The “ASSIGNED”
indicator is lit green for a tab that contains a selection.
If the mode is set to SINE WAVE 2CH, the signal is output to either odd (ODD(L) side)
or even (EVEN(R) side) of the selected channel. For example, the signal set to ODD(L)
is output in MIX1, and the signal set to EVEN(R) is output in MIX2.
You can press the CLEAR ALL button to defeat all selections.
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
4 Meter section
Indicates the oscillator output level.
5 OSCILLATOR OUTPUT button
Turns the oscillator output on or off. If you turn this button on, the oscillator signal will be
sent to the input channel or bus you selected in the ASSIGN section. When you press
the button again, the oscillator will turn off.
INTERVAL
WIDTH
Level
Time
Pink noise output
Turn BURST NOISE button on.
Meters
V5 Reference Manual
134
Meters
This chapter explains the METER screen that shows the input and output level meters for all
channels, and operations related to the optional MBCL meter bridge.
Operations in the METER screen
By accessing the METER screen, you can view the input and output levels of all channels on
the screen, and switch the level meter’s metering points (the points in the signal route at which
the level is detected). To access the METER screen, press the METER field of the Function
Access Area.
INPUT/OUTPUT/RTA tab
Use these tabs to switch between the INPUT METER screen, OUTPUT METER screen, and
RTA screen.
INPUT METER screen
This screen shows the meters and faders for all input channels.
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
OUTPUT METER screen
This screen shows the meters and faders for all output channels.
Meters
V5 Reference Manual
135
Fader level and meter display
This area displays the meter and fader for each channel.
1 Channel number
Indicates the channel number.
2 Σ clipping indicator
Lights to indicate that a signal is clipping at some point in the channel.
3 OVER indicator
Lights if the signal is clipping at the input section of the channel.
4 Meters
Indicates the input or output level of the channel.
5 Faders
The channel level is indicated by the fader position and by a numeric value (in dB) that
appears immediately below the fader. If the channel’s [ON] key is OFF, the fader turns
gray.
NOTE
Press any part of the meter area to assign the corresponding fader bank to the Centralogic
section.
Centralogic fader display
This area displays the level of faders that are currently set in the Centralogic section.
METERING POINT field
Select one of the following as the metering point at which the level will be detected. The
metering point for the level meter can be specified independently for input channels and
output channels.
For INPUT METER
PRE GC .................Immediately before GAIN
COMPENSATION
PRE D.GAIN ..........Immediately before DIGITAL GAIN
POST D. GAIN.......Immediately after DIGITAL GAIN
PRE FADER...........Immediately before the fader
(Immediately before INPUT DELAY)
POST ON...............Immediately after the [ON] key
For OUTPUT METER
PRE EQ .................Immediately before the EQ
PRE FADER...........Immediately before the fader
POST ON...............immediately after the [ON] key
NOTE
On the CL3 or CL1 console, the metering point for output channels will also affect the optional
meter bridge (MBCL).
PEAK HOLD button
Turn on this button to hold the peak level indication on each meter. Turn off this
button to clear the peak hold indication. PEAK HOLD button on/off operations
will affect both input channels and output channels as well as the MBCL meter
bridge. When you turn this button off, the peak level indication that had been
held will be cleared.
NOTE
You can also assign the PEAK HOLD button on/off function to a USER DEFINED key (page 224).
1
4
5
2
3
When the [ON] key for channel 7 is ON, and
the [ON] key for channel 8 is OFF
Meters
V5 Reference Manual
136
SHOW SEND LEVEL button
If you switch to SENDS ON FADER mode when this button is on, the color and
position of the faders in the INPUT METER screen show the type of send
destination bus, the send level to that bus, and ON/OFF status.
For INPUT METER
Fader color
The channel color is the same as the currently selected MIX/MATRIX bus (SEND
MASTER).
The position of the fader is the level of the signal sent to the bus.
The fader turns gray if you switch the SEND button to OFF or switch the channel OFF.
For OUTPUT METER
Only the fader for the signal sent from the MIX bus to the MATRIX bus changes color.
RTA METER screen
This is the real time analyzer screen. The results of a frequency analysis for the selected
source are shown in the 1/6 octave band (61 band).
1 Frequency Response graph
A graph of a frequency analysis is shown in the 1/6 octave band.
2 Source selection buttons
Use these buttons to specify the output channel whose frequency response you want to
see.
3 OVER display
Data that exceeds 0dB is shown the same as the OVER indicator.
4 Cross-hair cursor display
The frequency and level at the point you touch on the graph are displayed.
2
3
1
4 8
5
6
79
Meters
V5 Reference Manual
137
5 CUE OVERRIDE button
If this button is switched on, the cue signal set in the CUE screen is sent to the real time
analyzer, and an analysis is displayed.
If CUE MODE is set to MIX CUE, the frequency analysis is performed on a signal that is
a mix of all channels selected in the CUE screen.
If CUE MODE is set to 5.1 SOLO, the signal is treated as LAST CUE. In other words, the
frequency analysis is performed on the POST ON signal of the input channel.
If CUE is set to 2 channels, buttons will be as shown below.
6 BALLISTICS field
BALLISTICS button
Setting this switch to ON allows you to add rate of decay to the graph.
FAST/SLOW switch button
Use this button to set the rate of decay (FAST/SLOW).
7 HOLD button
Press this button to hold the graph that displays frequency response.
8 Offset gain
If a frequency is at a low level, its analysis results might not appear clearly in a graph.
The addition of offset gain allows better visibility in graphs for such results. You can
adjust this gain from 0dB to +30dB.
NOTE
The value for this parameter is applied identically to the RTA METER window, HPF/EQ window,
GEQ window, and PEQ window.
9 PEAK HOLD button
Turn on this button to hold the peak level indication on graphs of frequency analysis.
Turn off this button to clear the peak hold indication.
NOTE
The settings for the PEAK HOLD button, RTA button, and offset gain are stored even when the
console is turned off.
GEQ RACK 1-16 OUT
32
EFFECT RACK 1-8 OUT
16
CH 1-72{64,48} POST EQ
72{64,48}
ST IN 1L-8R POST EQ
16
MIX1-24 POST EQ
24
RTA
STEREO L,R,MONO(C) POST EQ
3
MATRIX 1-6,7-8(CUE B L,R) POST EQ
8
MIX OUT 1-24
24
STEREO OUT L,R,MONO(C)
3
MATRIX OUT 1-6,7-8(CUE B L,R)
8
CUE(A) OUT L,R
2
RTA
Meters
V5 Reference Manual
138
METER screen (Surround mode)
If you set a bus to Surround mode in BUS SETUP, the METER screen appears as shown
below.
1 MONITOR
Meters for MIX1-6. The layout for L R C LFE Ls and Rs is the same as the layout set in the
SURROUND SETUP screen.
2 SURROUND METER select button
Selects the meters displayed in the Function Access Area.
•MIX1-6
Source for MIX1-6.
MONITOR
Source selected in SURROUND MONITOR. For 2CH MONITOR, the layout remains 5.1,
but with meters only for L and R.
METER screen (when using 2-channel CUE)
1 CUE
Meters for CUE A and CUE B.
1 2
1
Meters
V5 Reference Manual
139
Function Access Area screen
If you set a bus to Surround mode in BUS SETUP, the METER screen in the Function Access
Area appears as shown below.
The display specifications are as follows.
The meter for the SURROUND signal is shown on the left side, and the meter for the
STEREO signal is shown on the right side. The layout for L R C LFE Ls and Rs is the
same as the layout set in the SURROUND SETUP screen.
When cue is operating
EFFECT CUE is shown on the right side, as usual.
The 5.1 SOLO CUE display is updated on the left side. However, if CUE MODE is set to
5.1 SOLO, no cue other than 5.1 SOLO CUE is possible.
Touch the CUE (or 5.1 SOLO) display area to clear the cue, as usual.
Using an MBCL meter bridge (optional) on the CL3
or CL1 console
If an optional meter bridge (MBCL) is installed on the CL3 or CL1 console, you will always be
able to view the output levels of MIX, MATRIX, STEREO, MONO, and CUE channels, in the
same way as in the meter section of CL5.
The MBCL meters indicate the MIX channel and MATRIX channel output levels in 12-segment
steps (OVER, -3dB, -6dB, -9dB, -12dB, -15dB, -18dB, -24dB, -30dB, -40dB, -50dB, -60dB).
You can select the metering point (the point at which the level is detected) from the following
choices. For information on how to change the metering point, refer to “Operations in the
METER screen” (page 134).
PRE EQ..................Immediately before the EQ
PRE FADER...........Immediately before the fader
POST ON ...............immediately after the [ON] key
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
140
Graphic EQ, Parametric EQ, Effects, and
PREMIUM RACK
This chapter explains how to use the built-in graphic EQ, parametric EQ, effects, and Premium
Rack.
About the virtual rack
CL series consoles enable you to use the built-in graphic EQ (subsequently abbreviated as
“GEQ”), parametric EQ (subsequently abbreviated as “PEQ”), and effects/processors to
modify signals. You can use two types of GEQ: 31BandGEQ which enables you to freely
adjust thirty-one bands (frequency regions), and Flex15GEQ which enables you to adjust any
fifteen of thirty-one bands. The 8Band PEQ allows you to freely adjust 8 bands (frequency
regions), and also features an HPF, an LPF, and 3 notch filters.
You can also use 54 different effect types. The CL series consoles feature Premium Rack,
which employs VCM technology. This technology models analog circuitry on a component
level to faithfully reproduce amazing analog sounds. The Premium Rack offers nine types of
processors.
In order to use a GEQ, PEQ, effect, or Premium Rack, you must mount the GEQ, PEQ, effect,
or Premium Rack in each virtual rack, and patch the input and output of that rack to the
desired signal route. In other words, the operation is just as though you had installed a signal
processor or effect device in an actual rack, and used patch cords to connect it. You can
mount a GEQ or PEQ instance in each of the sixteen racks 1-16 and EFFECT, an effect rack
instance in each of the eight racks 1-8, and a Premium Rack instance in each of the eight
racks 1-8.
Up to two channels of input and output can be used for each rack. (However, if the
“31BandGEQ” is mounted in a rack, there will be only one channel each for input and output.)
The figure below shows the signal flow for the virtual racks.
NOTE
In addition to the virtual racks for GEQ, PEQ, effects and Premium Rack, the CL console also
provides racks for mounting an I/O device (such as an R series) or external head amps (Yamaha
AD8HR, SB168-ES, etc.). For details, refer to “I/O devices and external head amps” (page 173).
With CL V1.7 and later, you can use the [SEL] key to switch channels in the EFFECT popup
window, GEQ popup window, and PREMIUM RACK popup window.
Pressing a top panel [SEL] key in the EFFECT popup window while operating the effect
parameter will switch to the window of the effect that is inserted in that channel. The same applies
to the GEQ popup window and the PREMIUM RACK popup window. You can also switch from
the EFFECT popup window to the GEQ popup window or PREMIUM RACK popup window. The
following items change according to the target channel.
Selected channel display in the Function Access Area
Operated channel in synchronized CL Editor
If there are no insert settings on a channel that has been selected, a notification dialog box will
be displayed.
MATRIX INSERT 1,2 IN 1-6,7-8(CUE B L,R)
MATRIX 1-6,7-8
(CUE B L,R)
MATRIX 1-6,7-8
(CUE B L,R)
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
141
Virtual rack operations
This section explains how to mount a GEQ, PEQ, or effect in the virtual rack, and patch the
input and output of the rack as an example.
NOTE
In steps 6 and 8, you can make settings such that the confirmation dialog box will not appear
(page 223).
The type of GEQ, PEQ, or effect mounted in each rack, its parameter settings, and the input-
source and output-destination settings are saved as part of the scene.
VIRTUAL RACK screen
1 Rack tabs
Selects the type of rack you want to display on the screen. Choose from GEQ 1-8, GEQ
9-16 (GEQ rack), EFFECT (effect rack), or PREMIUM (Premium Rack).
2 Rack mount button
Press this button to open the RACK MOUNTER window, in which you can select the type
of the rack you want to mount.
3 SAFE button
Switches Recall Safe on or off for the rack. If this button is turned on for a rack, the
contents and parameters of that rack will not change when a scene is recalled. For more
information on Recall Safe, refer to “Using the Recall Safe function” (page 82).
The Recall Safe settings of each rack will not preserve the input/output patching to that
rack. Recall Safe settings for patching must be made on the input-source or output-
destination channel.
STEP
1. In the Function Access Area, press the RACK button.
2. In the upper part of the VIRTUAL RACK window, press the GEQ 1-8, GEQ 9-16, or
EFFECT tab.
3. To mount a GEQ, PEQ, or effect in the rack, press the rack mount button for that
rack.
4. Use the buttons in the MODULE SELECT field in the RACK MOUNTER window to
select the item you want to mount, and press the OK button.
5. Press the INPUT PATCH button.
6. In the CH SELECT window, select the input source and then press the OK button.
7. Press the OUTPUT PATCH button.
8. In the CH SELECT window, select the output destination and then press the OK
button.
Function
Access Area
VIRTUAL RACK window
23 4 6 5
1
23 4 56
1
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
142
4 INPUT PATCH button
If the type is EFFECT, two buttons (L/R) will appear. If the type is Flex15GEQ or
8BandPEQ, two buttons (A/B) will appear. If the type is 31BandGEQ, one button will
appear.
Press this button to open the CH SELECT window, in which you can select the path of
the signal patched to the rack input.
The categories and channels that can be selected are shown below.
OUT CH ....................................MIX 1-24, MATRIX 1-8
*1
ST/MONO .................................STEREO L/R, MONO
*1
INSERT 1 OUT 1-32 .................CH1-32
*1
INSERT 1 OUT 33-64 ...............CH33-64
*1
INSERT 1 OUT 65-72 ...............CH65-72
*1
INSERT 1 OUT MIX/MATRIX.... MIX 1-24, MATRIX 1-8
INSERT 1 OUT ST/MONO........STEREO L/R, MONO
INSERT 2 OUT 1-32 .................CH1-32
*1
INSERT 2 OUT 33-64 ...............CH33-64
*1
INSERT 2 OUT 65-72 ...............CH65-72
*1
INSERT 2 OUT MIX/MATRIX.... MIX 1-24, MATRIX 1-8
INSERT 2 OUT ST/MONO........STEREO L/R, MONO
*1. Not displayed for GEQ 9-16 RACK.
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
In the case of the GEQ or PEQ, patching it to either an insert-out or insert-in will automatically
assign the other patch point to the same rack. Also, insert mode will automatically be switched
on. Additionally, if you defeat the insert-out or insert-in of a GEQ or PEQ, the other patch point
will automatically be defeated and at the same time insert mode will automatically be switched off.
For effects, if you select “DYNAMICS&EQ” for EFFECT TYPE, the operation is the same as for
GEQ above.
For PREMIUM RACK, the operation is the same as for GEQ above.
For more information on insert-in/out, refer to “Inserting an external device into a channel
(page 23).
5 OUTPUT PATCH button
If the type is EFFECT, two buttons (L/R) will appear. If the type is Flex15GEQ or
8BandPEQ, two buttons (A/B) will appear. If the type is 31BandGEQ, one button will
appear.
Press this button to open the CH SELECT window, in which you can select the path of
the signal patched to the rack output.
The categories and channels that can be selected are shown below.
CH1-32................................... CH1-32
*1
CH33-64................................. CH33-64
*1
CH65-72................................. CH65-72
*1
INSERT 1 IN 1-32 .................. CH1-32
*1
INSERT 1 IN 33-64 ................ CH33-64
*1
INSERT 1 IN 65-72 ................ CH65-72
*1
INSERT 1 IN MIX/MATRIX .... MIX 1-24, MATRIX 1-8
INSERT 1 IN ST/MONO......... STEREO L/R, MONO
INSERT 2 IN 1-32 .................. CH1-32
*1
INSERT 2 IN 33-64 ................ CH33-64
*1
INSERT 2 IN 65-72 ................ CH65-72
*1
INSERT 2 IN MIX/MATRIX .... MIX 1-24, MATRIX 1-8
INSERT 2 IN ST/MONO......... STEREO L/R, MONO
*1. Not displayed for GEQ 9-16 RACK.
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
If you use CL5 settings data on the CL3/CL1, or CL3 settings data on the CL1, buttons will be
shown crossed-out if they are assigned to a channel that does not exist on that model.
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
143
6 Rack container
Indicates the contents of the rack. This container varies depending on the rack type you
selected in the RACK MOUNTER window.
If nothing is mounted:
Press this area to open the RACK MOUNTER window, in which you can select the GEQ
or effect that will be mounted in the rack.
If 31BandGEQ is mounted:
This area indicates the settings for each band, GEQ on/off status, and input/output level.
Press this area to open the GEQ EDIT window, in which you can modify the GEQ
settings.
If Flex15GEQ is mounted:
This area indicates the settings for each band, the GEQ on/off status, and the input and
output levels for A and B respectively. Press this area to open the GEQ EDIT window, in
which you can modify the GEQ settings for A and B.
•If 8BandPEQ is mounted:
This area indicates the EQ frequency response, the PEQ on/off status, and the input and
output levels for A and B respectively. Press this area to open the PEQ EDIT window, in
which you can modify the PEQ settings for A and B.
If an effect is mounted (EFFECT rack only):
This area indicates the effect type, number of inputs and outputs, bypass on/off status,
and the input/output level. Press this area to open the EFFECT EDIT window, in which
you can modify the effect settings.
If 16ch Automixer is mounted (GEQ rack 1-8):
If 8ch Automixer is mounted (GEQ rack 1-4):
Press this area to open the AUTOMIXER EDIT window, in which you can modify the
automixer settings.
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
144
7 Link indicator
Indicates that an odd-numbered rack and even-numbered rack of the 31BandGEQ, A
and B of the Flex15GEQ, or A and B of the 8BandPEQ are linked to each other.
RACK MOUNTER window
Mount a GEQ, PEQ, or effect in the rack. This window will appear if you press the rack mount
button in the VIRTUAL RACK window.
1 Rack number
Indicates the number for the selected rack.
2 Virtual rack
This area indicates the GEQ or effect selected via the MODULE SELECT buttons.
3 MODULE SELECT field
Select the GEQ or effect that will be mounted in the rack. Each button has the following
function.
BLANK button....................... Removes the GEQ or effect currently mounted in the
rack; the rack will be empty.
31BandGEQ button .............. Mounts a 31BandGEQ in the rack.
Flex15GEQ button ................ Mounts a Flex15GEQ in the rack.
8BandPEQ button................. Mounts an 8BandPEQ in the rack.
EFFECT button (only for EFFECT rack)
........................ Mounts an effect in the rack.
16ch Automixer button (GEQ rack 1 only)
........................ Mounts a 16ch Automixer in the rack.
8ch Automixer button (GEQ rack 1 only)
........................ Mounts an 8ch Automixer in the rack.
NOTE
Input/output patching will be defeated when you change the item mounted in a rack.
The 16ch Automixer is used in racks 1 to 8, and the 8ch Automixer is used in racks 1 to 4.
4 CANCEL button
Cancels the changes you made in the RACK MOUNTER window, and closes the window.
5 OK button
Applies the changes you made in the RACK MOUNTER window, and closes the window.
NOTE
Be aware that if you remove a GEQ, PEQ, or effect that was mounted in a rack and close the
RACKMOUNTER window, all edits to the parameter settings for that GEQ, PEQ, or effect will be
discarded. If you have not yet closed the window, you can recover the parameter settings by
mounting the same GEQ, PEQ, or effect once again.
Graphic EQ operations
The CL series console enables you to mount a GEQ in GEQ racks 1-16 and patch it to the
insert-out/in of an input channel (GEQ 1-8 rack only), a MIX/MATRIX channel, or a STEREO/
MONO channel. You can also mount it in EFFECT racks 1-8 (FX 1-8) and patch it to the insert-
out/in of an input channel, MIX/MATRIX channel or STEREO/MONO channel. The gain of
each band can be adjusted using the Centralogic section’s faders and [ON] keys.
The following two types of GEQ are provided.
31BandGEQ
This is a monaural 31-band GEQ. Each band is 1/3
octave wide, the adjustable gain range is ±15 dB, and
the gain of all thirty-one bands can be adjusted.
If a 31BandGEQ is mounted in a rack, one channel of
input and output can be used for that rack.
Flex15GEQ
This is a monaural 15-band GEQ. Each band is 1/3
octave wide, and the adjustable gain range is ±15 dB.
The Flex15GEQ enables you to adjust the gain for
any fifteen of the same bands as the thirty-one bands
of the 31bandGEQ. (Once you have used up fifteen
bands of adjustment, you will not be able to adjust the gain of another band until you reset a
previously-adjusted band to the flat setting.)
A rack for which the Flex15GEQ is selected will have two Flex15GEQ units (shown as “A” and
“B” respectively) mounted in that rack, and will allow two channels of input and output.
7
43 5
21
43 5
21
INPUT
31BandGEQ
OUTPUT
Rack
INPUT
Flex15GEQ (B)
Flex15GEQ (A)
OUTPUT
Rack
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
145
Inserting a GEQ in a channel
This section explains how to insert a GEQ into the selected channel for use.
NOTE
If you are using a stereo source, you can mount a Flex15GEQ, or mount two 31BandGEQ units
in adjacent odd-numbered/even-numbered racks. This will let you link the two GEQ units in a later
step.
You can view the input and output levels of the GEQ in the rack in the GEQ field.
For details on GEQ operations, refer to the following section “Using the 31BandGEQ” (page 146)
or “Using the Flex15GEQ” (page 147).
GEQ EDIT window
NOTE
The windows for the 31BandGEQ and the Flex15GEQ are nearly identical. However, the
Flex15GEQ individually displays two GEQ units (A and B) mounted in a single rack.
1 Rack select tabs
Switch among GEQ 1-8 or among GEQ 9-16. For a rack in which a Flex15GEQ is
mounted, the tabs will be split as xA and xB (x is the rack number).
2 INPUT button
Press this button to open the CH SELECT window, in which you can select the input
source of the rack. The operating procedure is the same as for the INPUT button in the
GEQ field.
3 OUTPUT button
Press this button to open the CH SELECT window, in which you can select the output
destination of the rack. The operating procedure is the same as for the OUTPUT button
in the GEQ field.
4 RACK LINK button
Press this button to open the RACK LINK window, in which you can link adjacent GEQ units.
In the case of a 31bandGEQ, the GEQ units in adjacent odd-numbered/even-numbered
racks will be linked. In the case of a Flex15GEQ, the GEQ(A) and GEQ(B) within the same
rack will be linked.
•GEQ x
y button ( “x” and “y” are the rack number, or the rack number and
alphabetical character A or B)
The parameters of “x” will be copied to y,” and then linked.
•GEQ y
x button
The parameters of y” will be copied to x,” and then linked.
RESET BOTH button
The parameters of both will be initialized, and then linked.
CANCEL button
Cancels the link and closes the window.
NOTE
The RACK LINK button is shown only if linking is possible. When you link
GEQ units, a symbol will appear in the GEQ field to indicate the linked status.
5 FLAT button
Returns all bands of the currently-selected GEQ to 0 dB.
6 GEQ ON/OFF button
Switches the currently-selected GEQ on or off.
7 RTA button
Turn this button on to overlay a frequency response graph on the EQ.
STEP
1. Refer to steps 1-8 in “Virtual rack operations” (page 141) to mount a GEQ in a rack
and set its input source and output destination.
2. In the GEQ field, press the rack container in which you mounted the GEQ.
3. If you’re using a stereo source, press the RACK LINK button to link the two GEQ
units.
4. Press the GEQ ON/OFF button to turn the GEQ on.
27 8 3 4 5
6
1
9
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
146
8 HOLD button
Press this button to hold the peak of the graph that displays RTA.
9 Offset gain
If a frequency is at a low level, its analysis results might not appear clearly in a graph.
The addition of offset gain allows better visibility in graphs for such results. You can
adjust this gain from 0dB to +30dB.
NOTE
The value for this parameter is applied identically to the RTA METER window, HPF/EQ window,
GEQ window, and PEQ window.
Using the 31BandGEQ
You will use the Centralogic section’s faders 1-8 and [ON] keys to control the 31BandGEQ.
NOTE
When a fader of the Centralogic section is in the center (flat) position, the corresponding [ON] key
will go dark. This indicates that the corresponding band is not being modified. If you raise or lower
the fader even the slightest amount, the [ON] key will light, indicating that this band has been
modified. If you press a lit [ON] key to make it go dark, the corresponding band will immediately
return to the flat state.
With CL version 2.0 or later, pressing the [ON] key again for this band will restore the adjusted
gain value. In this way, comparison is easy and quick. However, please note that if the [ON] key
for this band is off and if you press the [ON] key for the fader of a different frequency band, the
adjusted gain value will be canceled and will return to ± 0dB.
If you switch the display to a different screen or rack, the fader assignments in the Centralogic
section will forcibly be defeated. However if you once again display the same rack, the faders will
automatically move to the group of bands you had previously been controlling.
When you close the GEQ EDIT window, the buttons in the FADER ASSIGN field automatically
turn off.
GEQ EDIT window (31BandGEQ)
1 EQ graph
Indicates the approximate response of the current 31Band GEQ.
2 Faders
Indicate the amount of boost and cut for each band of the 31BandGEQ. The actual
values are shown in the numerical boxes below.
Faders can be controlled by the TOUCH AND TURN function. The area of a fader you
touched will turn pink as shown below.
STEP
1. In the GEQ field rack, press the rack container in which you mounted the
31BandGEQ.
2. Press the GEQ ON/OFF button to turn the 31BandGEQ on.
3. Press one of the buttons in the FADER ASSIGN field to select the group of bands you
will control.
4. Use the faders in the Centralogic section to adjust the selected band.
5. When you’ve finished making settings, turn off the buttons in the FADER ASSIGN
field.
1
2
3
4
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
147
3 FADER ASSIGN field
In this field you can select the group of bands that will be controlled by the Centralogic
section’s faders. The buttons of the FADER ASSIGN field correspond to the following
groups of bands.
When you press one of these buttons, the faders for the bands selected on screen will
turn white, and the numbers of the corresponding faders in the Centralogic section will
be displayed. Now you can use the faders in the Centralogic section to control the
bands.
NOTE
The above operation is possible even if the Centralogic section is locked. When you turn off the
button in the FADER ASSIGN field, it will return to the locked state.
4 Tool buttons
Copy the currently-displayed 31BandGEQ settings to the GEQ of another rack, or
initialize the settings. For details on how to use the tool buttons, refer to Using the tool
buttons” in the separate Owner’s Manual.
NOTE
Only 31BandGEQ settings that use fifteen bands or less can be copied to a Flex15GEQ.
GEQ settings can be stored and recalled at any time using the dedicated library.
Using the Flex15GEQ
You will use the Centralogic sections faders 1-8 and [ON] keys to control the Flex15GEQ.
A rack in which a Flex15GEQ is mounted will show information for two GEQ units (A and B)
in the VIRTUAL RACK window.
NOTE
If you mount a Flex15GEQ, two monaural 31BandGEQ units will be placed in a single rack.
However, only up to fifteen bands can be adjusted for each unit.
NOTE
The [ON] key will light if you raise or lower a fader even the slightest amount. This indicates that
the corresponding band is being modified.
To quickly return a boosted or cut band to the flat position, press the corresponding [ON] key in
the Centralogic section to make it go dark.
With CL version 2.0 or later, pressing the [ON] key again for this band will restore the adjusted
gain value. In this way, comparison is easy and quick. However, please note that if the [ON] key
for this band is off and if you press the [ON] key for the fader of a different frequency band, the
adjusted gain value will be canceled and will return to ± 0dB.
If you switch the display to a different screen, the fader assignments in the Centralogic section
will forcibly be defeated. However if you once again display the same rack, the group of bands
you had previously been controlling will automatically be assigned to the faders.
When you close the GEQ window, the buttons in the FADER ASSIGN field automatically turn off.
20-100 The eight bands 20.0 Hz--100 Hz
63-315 The eight bands 63.0 Hz--315 Hz
200-1k The eight bands 200 Hz--1.00 kHz
630-3.15k The eight bands 630 Hz--3.15 kHz
2k-10k The eight bands 2.00 kHz--10.0 kHz
4k-20k The eight bands 4.00 kHz--20.0 kHz
STEP
1. Press the rack container in which you mounted Flex15GEQ.
2. Press the GEQ ON/OFF button to turn the Flex15GEQ on.
3. Press one of the buttons in the FADER ASSIGN field to select the group of bands you
will control.
4. Use the faders in the Centralogic section to adjust the selected band.
5. When you’ve finished making settings, turn off the buttons in the FADER ASSIGN
field.
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
148
GEQ EDIT window (Flex 15GEQ)
This window is the same as that for the 31BandGEQ, except that the AVAILABLE BANDS
parameter box indicates the real-time number of additional bands (maximum 15) that
can be controlled in the current GEQ.
For a rack in which a Flex15GEQ is mounted, the rack switch tabs will be split as xA and
xB (x is the rack number).
Parametric EQ operations
In addition to the standard 4-band EQ, CL series consoles also feature an 8-band parametric
EQ (PEQ) that can be rack mounted. You can mount this PEQ in GEQ racks 1-16 and patch
it to the insert-out/in of an input channel (GEQ 1-8 rack only), a MIX/MATRIX channel, or a
STEREO/MONO channel. You can also mount it in EFFECT racks 1-8 (FX 1-8) and patch it
to the insert-out/in of an input channel, MIX/MATRIX channel or STEREO/MONO channel.
The gain of each band can be adjusted using the Centralogic sections faders and [ON] keys.
The following type of PEQ is provided.
8BandPEQ
This is a monaural 8-band PEQ. There are also an independent HPF, LPF, and 3 notch filters.
Two 8BandPEQ units (shown as “A” and “B” respectively) can be mounted in a rack, and
therefore you can use two channels of input and output for each rack.
Inserting a PEQ in a channel
This section explains how to insert a PEQ into the selected channel for use.
NOTE
You can view the input and output levels of the PEQ in the rack in the GEQ or EFFECT field.
For details on PEQ operations, refer section “PEQ EDIT window” (page 149).
STEP
1. Refer to steps 1-8 in “Virtual rack operations” (page 141) to mount a PEQ in a rack
and set its input source and output destination.
2. In the GEQ field rack or the EFFECT field rack, press the rack container in which you
mounted the PEQ.
3. If you’re using a stereo source, press the RACK LINK button to link the two PEQ units.
4. Press the PEQ ON/OFF button to turn the PEQ on.
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
149
PEQ EDIT window
1 PEQ graph
Displays the parameter values for the PEQ and filter.
2 INPUT button
Press this button to open the CH SELECT window, in which you can select the input
source of the rack. The operating procedure is the same as for the INPUT button in the
GEQ field.
3 OUTPUT button
Press this button to open the CH SELECT window, in which you can select the output
destination of the rack. The operating procedure is the same as for the OUTPUT button
in the GEQ field.
4 LIBRARY button
Press this button to open the PEQ Library window.
5 DEFAULT button
Press this button to restore the default parameter setting.
6 COPY button
All EQ parameter settings will be copied in buffer memory.
7 PASTE button
Press this button to paste the copied settings from buffer memory to the current EQ. If
no valid data has been copied in the buffer memory, nothing will happen.
8 COMPARE button
Press this button to swap between the current EQ settings and the data stored in buffer
memory. If no valid data has been copied in the buffer memory, nothing will happen.
9 RACK LINK button
Press this button to open the RACK LINK window, in which you can link adjacent PEQ
units.
In the case of an 8BandPEQ, PEQ (A) and PEQ (B) within the same rack will be linked.
•GEQ x
y button ( “x” and “y” are the rack number, or the rack number and
alphabetical character A or B)
The parameters of x” will be copied to y,” and then linked.
•GEQ y
x button
The parameters of y” will be copied to x,” and then linked.
RESET BOTH button
The parameters of both will be initialized, and then linked.
CANCEL button
Cancels the link and closes the window.
NOTE
The RACK LINK button is shown only if linking is possible. When you link RACK units, a symbol
will appear in the GEQ field to indicate the linked status.
0 PEQ ON/OFF button
Switches the currently selected PEQ on/off.
A PEQ FLAT button
Press this button to reset the GAIN parameters of all PEQ bands to 0 dB.
All ON buttons for HPF, LPF, and notch filters are turned off.
All other parameter values are maintained and are not reset.
54 32
9
6 7 8ED
G
F
0
A
B
C
1
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
150
B PEQ IN/OUT level meters
Indicate the peak level of signals before and after the PEQ.
C Rack select tabs
Switch among GEQ 1-8, GEQ 9-16, or EFFECT 1-8. For a rack in which an 8BandPEQ is
mounted, the tabs will be split as xA and xB (x is the rack number).
NOTE
For details on how to use the buttons, refer to “Using the tool buttons” in the separate Owners
Manual.
D RTA button
Turn this button on to overlay a frequency response graph on the EQ.
E HOLD button
Press this button to hold the peak of the graph that displays RTA.
F EQ type select button
Switches the EQ type to PRECISE, AGGRESSIVE, SMOOTH, or LEGACY.
The following EQ types can be selected.
G Offset gain
If a frequency is at a low level, its analysis results might not appear clearly in a graph.
The addition of offset gain allows better visibility in graphs for such results. You can
adjust this gain from 0dB to +30dB.
NOTE
The value for this parameter is applied identically to the RTA METER window, HPF/EQ window,
GEQ window, and PEQ window.
PEQ EDIT window (8PEQ)
1 BYPASS button
You can bypass each band.
When the BYPASS button is on, the Q, FREQUENCY, and GAIN knobs for that band turn
gray.
2 HPF/LPF NOTCH button
Press this button to switch to the screen for operating HPF/LPF/notch filters.
3 EQ parameter setting knobs
Indicates the Q, FREQUENCY, and GAIN parameters for the BAND1 - BAND8 bands. You
can use a multifunction knob to adjust this.
PRECISE
This EQ type features “precisionand “controllability.” It can be used to
precisely adjust the desired points, to flexibly respond to a variety of music
production needs. The Low/High shelving filters have “Q” parameters that
allow knee adjustments.
AGGRESSIVE
This EQ type features “effective musical” characteristics. It allows you to
create an aggressive tone, making it a very powerful tool for artistic
expression.
SMOOTH
This EQ type focuses on a “smooth sound quality.” It allows you to create
natural sounds without significant modifications to the atmosphere of the
original sound.
LEGACY
This is the standard EQ type found in classic Yamaha digital mixers, such as
the PM1D and the PM5D. On the left side of the EQ graph, you can switch
between TYPE I (an algorithm used in previous Yamaha digital mixers) and
TYPE II (an algorithm that reduces interference between bands).
2
313
1
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
151
PEQ EDIT window (HPF/LPF NOTCH)
1 Attenuation select button
There are four types of HPF and LPF. This button switches the attenuation per octave
between -24 dB/oct, -18dB/oct, -12 dB/oct, and -6dB/oct.
2 8PEQ button
Press this button to switch to the screen for operating the 8-band PEQ.
3 HPF/LPF frequency knob
This knob is used to adjust the HPF/LPF frequency.
4 ON button
There is an ON button for the HPF, LPF, and each of the three notch filters.
5 Notch Filter Q knob
Adjusts the Q of the notch filter.
6 Notch Filter frequency knob
Adjusts the frequency of the notch filter.
About AUTOMIXER
Automixer is included as a standard feature on the CL series. Automixer searches for enabled
mics and automatically optimizes gain distribution, for uses such as speeches without scripts.
This allows uniform system gain to be maintained among multiple mics, freeing the engineer
from making constant fader adjustments.
Automixer operating principle
With the Dugan speech system used in Automixer, you can automatically adjust the automix
gain for up to 16 mics used for speeches.
The Dugan speech system functions differently from a limiter or auto level controller. When
multiple people are speaking, the engineer can adjust the each level using the faders as
normal. Even if nobody is speaking, the system searches for mic audio and automatically
distributes gain. Therefore, faders can be left in their raised positions.
4 6
2
3
4
1
1
54 654 65
4
3
When 1 person speaks on multiple mics When 2 people speak on multiple mics
When 1 person is speaking, the gain on the mic
being used is immediately increased and the gain
on all other mics is reduced. The same operation
occurs even if another person is speaking.
If 2 people are speaking at the same time, gain is
automatically distributed so that the total gain is
consistent across both mics, and the gain on the
remaining mic is reduced.
Gain (dB) in
Automix
Mic input audio
(dB)
Gain (dB) in
Automix
Mic input audio
(dB)
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
152
Inserting Automixer in channels post-fader
This section explains how to mount Automixer in a virtual rack, and insert Automixer input and
output into channels (excluding ST IN channels) post-fader (POST ON). For details on
Automixer operations, refer to the following section “Using Automixer.
Using Automixer
Channel display
The auto mix gain meter for each channel and man (yellow), auto (green), and mute (red)
settings are shown for channels 1-8 and channels 9-16.
If you select the channel 1-8 or 9-16 region, the display channel for the channel control field
will switch to 1-8 or 9-16.
(For 8ch Automixer, only channels 1-8 are shown.)
Channel control field
Each channel is always in man, auto, or mute mode. The indicator for the enabled channel
mode will light. To select a mode, either press the button for that mode or press the PRESET
button in the master field.
1 Level indicator
Lights green when the audio is at an optimum level for Automix.
NOTE
If the level indicator flashes, increase the input gain.
If the level indicator lights up red, reduce the input gain.
2 Meter indicator
There are three display modes. Pressing the meters button in the master field will switch
modes.
NOTE
Meters should normally be set in gain mode.
STEP
1. Refer to steps 1-8 in “Virtual rack operations” (page 141) to mount Automixer in
rack 1 and set its input source and output destination.
2. Refer to “Inserting an external device into a channel” (page 23) to insert Automixer
in post-fader (POST ON field).
Master field
Channel control field
gain Displays the gain for Automixer. Green
input Displays the input level. Yellow
output Displays the output level. Blue
8
5
3
7
6
4
2
1
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
153
3 weight
Adjusts the correlative sensitivity between input channels. When there is no input, adjust
the weight setting so that all auto mix gain meters are at about the same level. For
example, if you can hear noise near one mic (such as noise from a computer ventilation
fan or an air conditioner), you can suppress the noise by reducing the weight setting for
that channel.
To change the channel weight settings, use the multifunction knobs to adjust the weight
slider.
Automixer calculates the ratio of input level for specific channels for all input mixes in the
group. The following example explains the weight control mechanism.
When increasing the weight setting in one channel
The value displayed in the auto mix gain meter for that channel increases, while the
values for other channels are reduced.
Channels with high weight setting values receive a higher automix gain than other
channels.
When reducing the weight setting in one channel
The value displayed in the auto mix gain meter for that channel decreases, while the
values for other channels are increased.
When speaking into multiple mics at the same time, it is difficult to distinguish between
different mics.
4 group
Each channel can be assigned to three groups (a/b/c).
This group function is convenient for the following uses.
Using multiple rooms: Assign the mics in each room to their own groups, and use a
different Automixer for each.
Stereo pan: Assign mics panned to left, right and center to groups a, b, and c, to
maintain a stable stereo field.
5 override
If you turn on the OVERRIDE button in the master field, the channel will switch to man
mode or mute mode according to the settings for that channel’s override button.
When the channel’s override button is on, the mode for that channel will switch to man
when the master OVERRIDE button is turned on.
When the channel’s override is off, the mode for that channel will switch to mute when
the master OVERRIDE button is turned on.
When the master OVERRIDE button is turned off, the channel will return to its previous
mode.
The override function is convenient when the moderator of a panel discussion wants to
control the system.
Follow the instructions below to change the settings.
1. Turn on the override button on the moderator’s channel.
2. Turn off the override button on all other channels.
3. Turn on the OVERRIDE button in the master field as needed.
6 Channel number
Displays the channel number and channel name of the channel to be inserted.
7 man/auto/mute
Toggles between man/auto/mute.
man: Passes the audio through without changing the gain. This mode is used for singing
with a mic.
auto: Turns on Automixer. This mode is used for conversations.
mute: Mutes channels.
8 preset
Selects the channel mode (man/auto/mute) when the PRESET button in the master field
is pressed. The preset button lights when a preset is programmed for a channel.
Master field
1
OVERRIDE/PRESET/MUTE
Makes settings for each group (a/b/c) selected in the channel control field. Shows only
the selected group.
•OVERRIDE
When you press this button, channels where the channel override button is on will
fade in to 0 dB (unity gain). All channels with the override button turned off will be
muted.
PRESET
When you press this button, each channel will switch to the mode indicated by the
mode button (man/auto/mute) next to the lit preset indicator.
•MUTE
When you press this button, all channels will fade out immediately (0.5 seconds).
2 meters
Switches the meter indicator in the channel control field. Toggles between gain, input,
and output each time you press the button.
NOTE
Meters should normally be set in gain mode.
3 reset
Initializes the Automixer settings.
1
32
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
154
Editing the internal effects
The internal effects of the CL series console can be mounted in EFFECT racks 1-8, and
patched to an output channel’s output or input channel’s input, or inserted into a channel. For
each effect mounted in a rack, you can choose one of 54 types of effect.
With the default settings, the signals from MIX channels 17-24 are input to racks 1-8, and from
the racks are then output to ST IN 1-8 (L/R).
NOTE
Some effect types can be mounted only in racks 1, 3, 5 or 7.
To use an internal effect via send and return, assign the output of a MIX channel to the input
of the effect, and assign the output of the effect to an input channel. In this case, the
corresponding output channel is used as a master channel for the effect send, and the input
channel is used as an effect return channel.
Alternatively, you can assign the input and output of the internal effect to the insert-out/in of a
desired channel (except for a ST IN channel), so that the effect is inserted into that channel.
The internal effects fall into two categories; “STEREO type” (2-in/2-out) effects that process
the L/R channel input signals independently, and “MIX type” (1-in/2-out) effects that mix the
two channels before processing them.
If signals are assigned to both the L and R inputs of an effect, the way in which the L/R
channels are processed will depend on whether a Stereo effect type or a Mix effect type is
selected, as follows.
STEREO type effects
MIX type effects
If a signal is assigned to only one input of a two-input effect, it will be processed as mono-in/
stereo-out regardless of whether a Stereo effect type or Mix effect type is selected. However,
please note that this will not apply to COMP276, COMP276S, COMP260, COMP260S,
EQUALIZER601, and OPENDECK.
Using an internal effect via send and return
This section explains how to use a MIX bus as an effect send bus and a ST IN channel as an
effect return channel, so that the effect can be used in a send and return configuration.
NOTE
If you want to use a MIX bus as an effect send bus, select “VARI” as the bus type. This will allow
you to adjust the send level separately for each input channel.
If you want to use the input to an effect in stereo, it can be convenient to assign the send-
destination MIX bus to stereo. (For details on bus assignments, refer to page 58.)
OUTPUT PATCH
INPUT PATCH
EFFECT
EFFECT
EFFECT
EFFECT
Rack 2
Rack 7
Rack 8
Output of the
output
channel
Input of the input
channel
Rack 1
EFFECT
Insert-out of a
desired channel*
Insert-in of a
desired channel*
* Excluding a ST IN channel
STEP
1. Follow steps 1-3 described in “Virtual rack operations” (page 141), to mount an
effect in a rack.
2. Press the INPUT PATCH L button in the VIRTUAL RACK window, and select a MIX
channel as the input source for the rack (page 141).
3. Press the OUTPUT PATCH L button in the VIRTUAL RACK window, and select the L
input of a ST IN channel as the output destination for the rack (page 141).
4. Adjust the send level from each channel in the TO MIX/TO MATRIX field in the
OVERVIEW screen.
5. Adjust the master level of the effect send of the MIX channel you selected as the
input source for the rack.
6. Adjust the effect return level of the ST IN channel you selected as the output
destination for the rack.
INPUT L EFFECT L L RETURN
INPUT R EFFECT R R RETURN
INPUT L L RETURN
INPUT R
EFFECT
R RETURN
L RETURN
EFFECT
R RETURN
INPUT L
or R
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
155
NOTE
If youre using a stereo source, assign the L/R signals of the stereo MIX channels to the L/R inputs
of the rack.
If youre using the output of the effect in stereo, assign the R input of the ST IN channel selected
in step 3 to the R output of the rack.
You can select more than one output destination for the effect.
For more information on setting the effect parameters, refer to “Editing the internal effect
parameters” (page 156).
Adjusting the effect send level of a input channel
In the TO MIX/TO MATRIX field in the OVERVIEW screen, press and select the TO MIX SEND
LEVEL knob for the MIX bus set as the input source for the rack, and use the multifunction
knob to adjust the send level of the signal sent from each channel to that MIX bus.
NOTE
If a MATRIX bus is shown in the TO MIX/TO MATRIX field, use the [MIX 1-16] key or the [MIX 17-
24/MATRIX] key in the SELECTED CHANNEL section to select the MIX bus at the input source
for the rack.
When adjusting the effect send level, make sure that the send level from the ST IN channel you
selected as the output destination for the rack to the corresponding MIX bus is set to 0. If you
raise this send level, the output of the effect will be returned to the input of the same effect,
possibly causing oscillation.
If you press the knob once again, the MIX SEND window (8ch) for the send-destination MIX bus
will appear. This window contains on/off switches for the signals sent from each channel to the
corresponding bus, and lets you select the send point (PRE or POST) (page 45).
Adjusting the master level of the effect send
To adjust the MIX channel you specified as the input source for the rack, first call it up to the
Centralogic section and then make adjustments by operating the fader.
Set the level as high as possible without allowing the post-effect signal to reach the overload
point.
NOTE
The input and output levels of the effect are shown by the input/output meters in the upper right
of the EFFECT EDIT window.
Adjusting the effect return level
To adjust the effect return level, first call up the ST IN channel you specified as the output
destination for the rack to the Centralogic section and then make adjustments by operating
the fader.
Inserting an internal effect into a channel
This section explains how to insert an effect into a channel by assigning the input/output of
the internal effect to the input/output of the desired channel (except for a ST IN channel). For
details on editing the effect parameters, refer to “Editing the internal effect parameters.
NOTE
If you are inserting an effect into a channel that handles a stereo source, assign the R channel
insert-out/insert-in to the R input and output of the effect in the same way as step 3.
For more information about how to operate the INSERT/DIRECT OUT window, refer to “Inserting
an external device into a channel” (page 23).
The levels before and after the effect are shown by the input and output meters in the upper right
of the EFFECT EDIT window.
Adjust the effect send master level and the effect parameters so that the signal does not reach
the overload point at the input or output stage of the effect.
STEP
1. Follow steps 1-3 described in “Virtual rack operations” (page 141), to mount an
effect in a rack.
2. Press the INPUT PATCH L button in the VIRTUAL RACK window, and select the insert-
out for one of the channels as the input source for the rack (page 141).
3. Press the OUTPUT PATCH L button in the VIRTUAL RACK window, and select the
insert in of the same channel as the output destination for the rack (page 141).
4. Use the Bank Select keys in the Centralogic section to access the OVERVIEW screen
for the channel into which you inserted the effect.
5. Press the INSERT/DIRECT OUT field in the OVERVIEW screen.
6. In the INSERT/DIRECT OUT popup window, turn on the INSERT ON/OFF button for
the channel into which you inserted the effect.
7. Display the EFFECT EDIT window again, and select the effect type and edit the effect
parameters.
8. Using the fader of the channel you selected as the rack’s output destination in step
3, adjust the level as appropriate.
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
156
Editing the internal effect parameters
This section explains how to change the effect type and edit the parameters. For a rack in
which an effect is mounted, the following information is shown in the VIRTUAL RACK window.
1 Effect title/type
Displays the effect title, the name of the type that is used, and a graphic. The number
of input and output channels (1 IN/2 OUT or 2 IN/2 OUT) of this effect is also shown.
2 Input/output meters
Indicate the level of the signals before and after the effect.
EFFECT EDIT window
Allows you to adjust the effect parameters.
NOTE
For details on the parameters of each effect type, refer to the data list at the end of this manual.
1 INPUT L/R buttons
Press this button to open the CH SELECT window.
2 OUTPUT L/R buttons
Press this button to open the CH SELECT window.
3 Effect type field
Displays the effect title, the name of the type that is used, and a graphic. The number
of input and output channels (1 IN/2 OUT or 2 IN/2 OUT) of this effect is also shown.
Press this field to open the EFFECT TYPE window, in which you can select the effect type.
STEP
1. Press the rack container in which the effect you want to edit is mounted.
2. To change the effect type, press the effect type field in the EFFECT EDIT window, and
select the effect type in the EFFECT TYPE window.
3. Press a knob in the effect parameter field in the EFFECT EDIT window to select it,
and turn the multifunction knob to edit the effect parameters.
4. Edit the settings in the special parameter field as necessary.
1 2
7
6
0
1
A
8
3 24 5
9
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
157
NOTE
You can also change the effect type by recalling a library setting.
Effect types “HQ.PITCH” and “FREEZE” can be used only in rack 1, 3, 5, or 7. Also, even if you
copy these two effect types, you will not be able to paste them to rack 2, 4, 6, or 8.
4 EFFECT CUE button
Cue-monitors the output of the currently-displayed effect. This Cue function is valid only
while this screen is displayed. The cue will be canceled automatically when you switch
to a different screen.
NOTE
If the Cue mode is set to MIX CUE, all channels for which the CUE key is turned on will be
monitored. However, only the output signal of the effect will be monitored if you turn on the
EFFECT CUE button. (The [CUE] keys that had been turned on until then will be temporarily
defeated.)
The cue monitoring does not support CUE B.
5 Special parameter field
Indicates special parameters that are specific to some effect types.
TEMPO
This field appears if a tempo-type or modulation-type effect is selected.
MIDI CLK button
If you turn this button on, the BPM parameter of that
effect will be set to match the tempo of the MIDI timing
clock being input from the MIDI port.
PLAY/REC
This field appears if FREEZE is selected as the effect type.
PLAY button/REC button
Enable you to record (sample) and play back when using
the freeze effect. For detailed operations, refer to Using
the Freeze effect” (page 161).
SOLO
This field appears if M.BAND DYNA. or M.BAND COMP. is
selected as the effect type.
•HIGH/MID/LOW buttons
Allow only the selected frequency band to pass (multiple
selections are allowed).
Gain reduction meters
Indicate the amount of gain reduction for each band.
Gain reduction meter
This field appears if Comp276/276S or Comp260/260S is
selected as the effect type.
Gain reduction meters
Indicate the amount of gain reduction applied by the
compressor.
Type
This field is displayed when Equalizer601 is selected as the effect
type.
•Type
Select one of two equalizer types that feature different effects.
DRIVE emulates changes in frequency response of analog circuits,
creating a driven sound that enhances analog characteristics by adding some distortion.
CLEAN emulates changes in frequency response that are typical of analog circuits,
creating a clear non-distorted sound that is inherently digital.
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
158
•FLAT button
This button resets the gain of all bands to 0dB.
6 BYPASS button
Temporarily bypasses the effect.
7 Input/output meters
Indicate the level of the signals before and after the effect.
8 Effect parameter field
This area indicates parameters for the currently-selected effect type. When you press a
knob in this field, you will be able to use the multifunction knobs to control the
corresponding horizontal row of knobs.
You can also make fine adjustments by rotating a knob while pressing and holding it
down.
9 MIX BAL. knob
Adjusts the balance between the original sound and effect sound included in the output
signal from the effect. If you press this knob to select it, you will be able to adjust it using
the corresponding multifunction knob. If you are using the effect via send and return,
set this to 100% (effect sound only).
0 Tool buttons
Copy the currently-displayed effect settings to the effect of another rack, or initialize the
settings. For details on how to use the tool buttons, refer to Using the tool buttons” in
the separate Owner’s Manual.
NOTE
Effect settings can be stored and recalled at any time using the effect library.
A Rack select tabs
Enable you to switch between EFFECT 1–8.
Using the Tap Tempo function
“Tap tempo” is a function that lets you specify the delay time of a delay effect or the modulation
speed of a modulation effect by striking a key at the desired interval. The Tap Tempo function
can be used for delay-type and modulation-type effects in which the BPM parameter is
included, and specify the delay time or modulation speed. To use the Tap function, you must
assign Tap Tempo to a USER DEFINED key, and then operate that USER DEFINED key.
NOTE
For details on the parameters of each effect type, refer to the data list at the end of this manual.
Assigning the Tap Tempo function to a USER DEFINED key
STEP
1. In the Function Access Area, press the SETUP button.
2. Press the USER SETUP button in the upper left of the SETUP screen.
3. Press the USER DEFINED KEYS tab in the USER SETUP window.
4. On the USER DEFINED KEYS page, press the button for the USER DEFINED key to
which you want to assign the Tap Tempo function.
5. Select “TAP TEMPO” in the FUNCTION column, select “CURRENT PAGE” in the
PARAMETER 1 column in the USER DEFINED KEY SETUP window, and press the OK
button.
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
159
NOTE
If you specify “CURRENT PAGE” in the PARAMETER 1 column in the USER DEFINED KEY
SETUP window, the Tap Tempo function can be used for the currently-displayed effect (rack).
If you specify “RACK x” (x=1-8) in the PARAMETER 1 column in the USER DEFINED KEY
SETUP window, you can use the Tap Tempo function only for a specific effect (rack).
For more information on USER DEFINED keys, refer to “USER DEFINED keys” (page 224).
Using the Tap Tempo function
The average interval (BPM) at which you press the USER DEFINED key will be calculated,
and that value will be applied to the BPM parameter.
NOTE
If the average value is outside the range of 20-300 BPM, it will be ignored.
If you turn on the MIDI CLK button in the special parameter field, the BPM parameter value will
change in relation to the tempo of the MIDI timing clock received from the MIDI port.
USER SETUP windowSETUP screen
USER DEFINED KEY SETUP windowUSER DEFINED KEYS page
STEP
1. In the Function Access Area, press the RACK button.
2. Press the EFFECT tab in the VIRTUAL RACK window.
3. Press the rack container in which the effect you want to control is mounted.
4. Press the effect type field in the EFFECT EDIT window.
5. In the EFFECT TYPE window, select an effect type that includes a BPM parameter.
6. Set the SYNC parameter ON in the effect parameter field.
7. At the desired tempo, repeatedly press the USER DEFINED key to which you
assigned the Tap Tempo function, to set the BPM parameter.
ab c
The average interval will be input to the parameter.
(the average of a, b, and c)
First tap Second tap Third tap Fourth tap
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
160
NOTE
If the EFFECT EDIT popup window used to set TAP TEMPO is open, this popup window is not
displayed.
With CL V3.0 and later, the delay value (msec) is also shown in the popup window.
Effects and tempo synchronization
Some effects of the CL series can be synchronized with the tempo. There are two such types
of effect: delay-type effects and modulation-type effects. For delay-type effects, the delay time
will change according to the tempo. For modulation-type effects, the frequency of the
modulation signal will change according to the tempo.
Parameters related to tempo synchronization
The following five parameters are related to tempo synchronization.
1) SYNC 2) NOTE 3) TEMPO 4) DELAY 5) FREQ.
SYNC: ..............................This is the on/off switch for tempo synchronization.
NOTE and TEMPO: .........These are the basic parameters for tempo synchronization.
DELAY and FREQ.: ..........DELAY is the delay time, and FREQ. is the frequency of the modulation
signal. These directly affect the way in which the effect sound will
change. DELAY is relevant only for delay-type effects, and FREQ. is
relevant only for modulation-type effects.
How the parameters are related
Tempo synchronization calculates the DELAY (or FREQ.) value
*a
from the TEMPO and
NOTE.
Turn SYNC ON
Change NOTE DELAY (or FREQ.) will be set
In this case, the DELAY (or FREQ.) value is calculated as follows.
DELAY (or FREQ.) = NOTE x 4 x (60/TEMPO)
Change TEMPO DELAY (or FREQ.) will be set
In this case, the DELAY (or FREQ.) value is calculated as follows.
DELAY = NOTE x 4 x (60/TEMPO) sec
FREQ. = (TEMPO/60) / (NOTE x 4) Hz
Example 1: When SYNC=ON, DELAY=250 ms, TEMPO=120, you change NOTE from
8th note to quarter note
DELAY= new NOTE x 4 x (60/TEMPO)
= (1/4) x 4 x (60/120)
= 0.5 (sec)
= 500 ms
Thus, the DELAY will change from 250 ms to 500 ms.
Example 2: When SYNC=ON, DELAY=250 ms, NOTE=8th note, you change TEMPO
from 120 to 121
DELAY= NOTE x 4 x (60/new TEMPO)
= (1/8) x 4 x (60/121)
= 0.2479 (sec)
= 247.9 (ms)
Thus, the TEMPO will change from 250 ms to 247.9 ms.
*a Rounded values are used for the calculation results.
Special characteristics of the TEMPO parameter
The TEMPO parameter has the following characteristics that are unlike other parameters.
Value shared with all effects (However, this applies only if SYNC is ON and if the MIDI CLK
button is ON when MIDI clock is input to the MIDI IN jack.)
You cannot store it to or recall it from the Effects Library. (You can store it to and recall it from
a Scene.)
This means that the TEMPO value may not necessarily be the same when an effect is recalled
as when that effect was stored. Here is an example.
Store the effect: TEMPO=120 Change TEMPO to 60 TEMPO=60
Recall the effect: TEMPO=60
Normally when you change the TEMPO, the DELAY (or FREQ.) will be re-set accordingly.
However if the DELAY (or FREQ.) were changed, the effect would sound differently when
recalled than when it was stored. To prevent the effect from changing in this way between
store and recall, the CL series does not update the DELAY (or FREQ.) value when an effect
is recalled, even if the TEMPO is no longer the same as when that effect was stored.
* The NOTE parameter is calculated based on the following values.
Tap Tempo pop-up window
= 1/48
= 3/16
= 1/24
= 1/4
= 1/16
= 3/8
= 1/12
= 1/2
= 3/4
= 3/32
= 1/8
= 1/1
= 2/1
= 1/6
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
161
Using the Freeze effect
This section explains how to use the “FREEZE” effect type, which provides the functionality
of a simple sampler. When this effect type is selected, you can perform operations on screen
to record (sample) and play back a sound.
NOTE
Effect types “FREEZE” and “HQ.PITCH” can be used only in rack 1, 3, 5, or 7.
NOTE
The bar in the EFFECT EDIT window reflects the current recording progress. When a fixed time
has elapsed, the buttons will automatically turn off.
You can adjust the parameters in the EFFECT EDIT window to make detailed settings for
recording time, the way in which recording will begin, and the way in which the sample will play
back. For details on the parameters, refer to the data list at the end of this manual.
The sampled content will be erased if you record another sample, change the effect, or turn off
the power to the CL unit.
EFFECT EDIT window (when FREEZE is selected)
If the “FREEZE” effect type is selected, a PLAY button, REC button, and progress bar will
appear in the special parameter field.
1 PLAY button
2 REC button
3 Progress bar
NOTE
As an alternative to switching the effect type, you can also recall settings that use the “FREEZE”
effect type from the effect library.
Using the Premium Rack
In addition to the graphic EQ and the internal effects, the CL series provides “Premium Rack”
processors that faithfully emulate carefully selected vintage analog processors as well as
newly developed processors. The Premium Rack employs VCM technology, which models
analog circuitry on a component level to faithfully reproduce and fine-tune amazing analog
sounds.
The Premium Rack offers nine types of processors.
STEP
1. In the Function Access Area, press the RACK button.
2. Press the EFFECT tab in the VIRTUAL RACK window.
3. Press the effect container in rack 1, 3, 5, or 7.
4. Press the effect type field in the EFFECT EDIT window to open the EFFECT TYPE
window, and select “FREEZE.”
5. To begin recording (sampling), press the REC button and then press the PLAY
button.
6. To play back the recorded sample, press the PLAY button.
Name Outline
Portico 5033 Models RND’s analog 5-band EQ.
Portico 5043 Models RND’s analog compressor/limiter.
Portico 5045 Models RND’s primary source enhancer.
U76 Models a typical vintage compressor/limiter.
Opt-2A Models a classic vacuum tube (optical type) compressor.
EQ-1A Models a classic vacuum tube passive-type vintage EQ.
Dynamic EQ
Newly-developed EQ that features a dynamically changing gain and enables you to
control the cut/boost amount in relation to the input level.
Buss Comp 369 Models a 1970s compressor/limiter with discrete circuitry.
MBC4 Four-band compressor with intuitive controls
1 32
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
162
Using the Premium Rack
The procedure to set up the I/O patches for the rack are the same as those for the effect rack
(page 154).
NOTE
If you are inserting a processor into a channel that handles a stereo source, assign the R channel
insert-out and insert-in to the R input and output of the processor in the same way as steps 5 and 6.
For details on editing the parameters, refer to the next section “Editing the Premium Rack
parameters.
Adjust the digital gain and the processor parameters so that the signal does not reach the
overload point at the input or output stage of the processor.
Mounting a processor
There are two ways to mount each processor:
DUAL .....................The processor is used on two mono channels.
STEREO ................The processor is used on one stereo channel.
The DUAL button and STEREO button indicate how many rack space units are occupied by
the Premium Rack processor.
The U76 occupies two rack spaces. Other processors occupy one rack space. If you mount a
two-space Premium Rack processor in the rack, you will be unable to mount any more
processors below those rack spaces. Also, you cannot mount a two-space processor in an
even-numbered rack.
Editing the Premium Rack parameters
Each Premium Rack window includes the following items:
STEP
1. In the Function Access Area, press the RACK button.
2. Press the PREMIUM tab in the upper part of the VIRTUAL RACK window.
3. To mount a Premium Rack in the rack, press the rack mount button for that rack in
the PREMIUM RACK field.
4. Select the processor to mount and the mounting method in the MODULE SELECT
field in the PREMIUM RACK MOUNTER window, and press the OK button.
5. Press the INPUT PATCH L button to open the CH SELECT window, and select the
input source.
6. Press the OUTPUT PATCH L button to open the CH SELECT window, and select the
insert-in of the same channel as the output destination.
7. Use the Bank Select keys in the Centralogic section to select the channel into which
you inserted the effect.
8. Press the INSERT/DIRECT OUT field in the OVERVIEW screen.
9. In the INSERT/DIRECT OUT popup window, turn on the INSERT ON/OFF button for
the channel into which you inserted the processor.
10. Adjust the processor parameters.
11. Using the fader of the channel you selected as the rack’s output destination in step
6, adjust the level as appropriate.
PREMIUM RACK MOUNTER
window
VIRTUAL RACK window
(PREMIUM RACK field)
1 2 3
4
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
163
1 ASSIST button
Press this button to indicate the numbers of the multifunction knobs that control each
parameter.
2 LIBRARY button
Press this button to display the Library window for each Premium Rack.
3 DEFAULT button
Restores the default parameter setting.
4 Multifunction knob access field
Indicates the name and value of the parameters that are assigned to the multifunction
knobs.
To switch the parameter to control, press the knob in the window.
NOTE
If the ASSIST button is on, you will be able to easily identify the parameters that are currently
available for editing, and the parameters that will be available for editing after you select them.
You can adjust the parameter in finer steps by turning a multifunction knob while pressing and
holding it down.
Portico 5033
Portico 5033 is a processor that emulates a 5-band analog EQ developed by Rupert Neve
Designs (RND). 5033EQ features a unique tone control response. It inherited the history of
the “1073,” which was praised as one of the greatest devices developed by Mr. Rupert Neve.
Yamaha’s VCM technology has modeled the EQ to the last detail, including the input/output
transformer that was designed by Rupert Neve himself. As a result, this processor model
produces musically high-quality sound even when bypassed. Its response features unique
effects. For example, if the Lo setting is cut, the low range becomes tight, and if the Hi setting
is raised, the desired range will be boosted without hurting your ears.
1 ALL BYPASS button
Switches EQ bypass on or off. Even in the bypassed state, the signal will pass through
the input/output transformers and the amp circuit.
2 TRIM knob
Adjusts the input gain of the effect.
3 LF/LMF/MF/HMF/HF Frequency knobs
Adjust the frequency for each band.
4 LF/LMF/MF/HMF/HF Gain knobs
Adjust the amount of boost or cut for each band.
5 LMF/MF/HMF Q knobs
Adjust the Q (steepness) of each band. The higher the Q value, the narrower the range
in which you can control the gain for the band.
6 LMF/MF/HMF IN button
Turn LMF/MF/HMF EQ on or off respectively.
7 LF/HF IN button
Turn LF and HF EQ on or off simultaneously.
8 Graph
Indicates the graphical EQ response.
1
2
8
7
3
4
5
6
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
164
Portico 5043
Portico 5043, like Portico 5033, is a processor that emulates RNDs analog compressor. The
actual 5043 compressor is equipped with the same input/output transformer as that of the
5033 EQ, delivering a natural, analog-like tonality and effect. It enables you to obtain a range
of results from hard compression to natural sound, and is suitable for a broad range of audio
sources ranging from drums to vocals. The most notable feature of this model is that you can
switch the gain reduction type. You can choose either an FF (Feed-Forward) circuit type
(which is the current mainstream), or an FB (Feed-Back) circuit which was typically used in
vintage compressors. This allows you to create sounds with various characteristics as
appropriate for your applications.
1 IN button
Turns the compressor’s bypass on or off. When the compressor is bypassed, the button
indicator will turn off. However, even if the compressor is bypassed, the signal will pass
through the input/output transformer and amp circuits.
2 INPUT meter
Indicates the input signal level.
One meter appears in DUAL mode, and two meters appear in STEREO mode.
3 FB button
Switches the gain reduction method between FF (Feed-Forward) circuit and FB (Feed-
Back) circuit. The button will light when FB circuit is selected.
The FF circuit is used in most contemporary compressors. This type is useful when you
want to apply consistent compression while maintaining a consistent tonal color.
The FB circuit is used in vintage compressors. This type is suitable when you want to
apply a smooth compression while adding a tonal character that is characteristic of such
devices.
4 GAIN REDUCTION meter
Indicates the amount of gain reduction.
5 THRESHOLD knob
Adjusts the threshold at which compression starts to be applied.
6 RATIO knob
Adjusts the compression ratio. If you rotate the knob fully clockwise, the unit will operate
as a limiter.
7 ATTACK knob
Adjusts the compressor’s attack time.
8 RELEASE knob
Adjusts the compressor’s release time.
9 GAIN knob
Adjusts the output gain.
Portico 5045
This is a processor that accurately models the Portico 5045 Primary Source Enhancer made
by Rupert Neve Designs. Operation is extremely easy, allowing you to suppress background
noise that enters the mic while increasing clarity, enhancing the primary source and also
improving the feedback margin. It is suitable not only for a hand-held mic but also for a lavalier
mic or headset mic, and can be used in a variety of situations including event PA, concerts,
or broadcast. This processor is also equipped with the audio transformer and discrete amp
circuit that are the signature of the Portico series, so that simply passing the signal through it
will increase the luster and depth of the sound.
1 PROCESS ENGAGE button
Turns the enhancement circuit on/off.
2 RMS/PEAK button
Selects the operation mode for the level detector. You can select RMS mode or PEAK
mode.
1324
56789
1 23 54 6
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
165
3 TIME CONSTANT knob
Switches the attack and release time. The settings are as follows.
4 THRESHOLD knob
Adjusts the level at which enhancement begins. Signals below the THRESHOLD are
attenuated.
5 PROCESS ACTIVE indicator
This indicator is lit when the input signal exceeds the THRESHOLD. Adjust the
THRESHOLD so that this indicator is lit when the primary audio source is being input,
and unlit during periods of silence or between phrases.
6 DEPTH knob
Adjusts the amount of attenuation for signals below the THRESHOLD.
U76
U76 is a processor that emulates a popular vintage compressor used in a wide range of
situations. This processor does not provide the threshold parameter that is found on
conventional compressors. Instead, the intensity of compression is determined by the
balance between the input gain and the output gain. The “All mode” setting for the RATIO
parameter allows you to create a heavily-compressed sound that is typical of this model. It
produces an aggressive tonal character with a rich addition of overtones.
1 INPUT knob
Adjusts the input level. As the input level gets higher, more compression is applied.
2 ATTACK knob
Adjusts the compressor’s attack time. Fully rotate the knob clockwise to set the fastest
attack time.
3 RELEASE knob
Adjusts the compressor’s release time. Fully rotate the knob clockwise to set the fastest
release time.
4 RATIO switch buttons
Use these five buttons to set the compression ratio.
A button with a higher number will raise the compression ratio more. Pressing the ALL
button selects All mode, in which the RATIO will become high, and sharp compression
with a faster release time will be applied, creating substantially-distorted aggressive
sound.
5 METER switch buttons
Switch the meter display.
GR.................Indicates the amount of gain reduction applied by the compressor.
+4/+8.............Each meter uses -18 dB as the reference level of the output signal, and
indicates “0VU” for the value of the reference level added by +4 dB or
+8 dB.
OFF...............Turns off the meter display.
6 OUTPUT knob
Adjusts the output level.
If you have adjusted the amount of gain reduction by changing the INPUT knob, the
level of audible volume will also change. In this case, use the OUTPUT knob to adjust
the volume level.
RMS Mode PEAK Mode
A: 50 ms
B: 100 ms
C: 200 ms
D: 750 ms
E 1.5 s
F: 3 s
Attack: fixed at 20 ms
Release: A: 20 ms
B: 200 ms
C: 1 s
D: 2 s
E: 5 s
F: 30 s
21
3645
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
166
Opt-2A
Opt-2A is a processor that emulates a popular vintage model of tube optical compressors. To
control the level, it uses optical components such as a CdS cell and an EL panel to apply
smooth compression, with beautiful high-range overtones generated by warm-sounding
vacuum tube distortion, delivering an elegant and sophisticated sound.
1 GAIN knob
Adjusts the output level.
2 PEAK REDUCTION knob
Adjusts the compression amount of the signal.
3 RATIO knob
Adjusts the compression ratio.
4 METER SELECT knob
Switches the meter display.
GAIN REDUCTION indicates the amount of gain reduction applied by the compressor.
With -18 dB as the reference level of the output signal, the OUTPUT +10 and OUTPUT
+4 settings respectively will cause the value +10 dB or +4 dB from this reference level to
be shown as “0VU” on the meter.
EQ-1A
EQ-1A is a processor that emulates a famous passive-type vintage EQ. It features a unique
style of operation, allowing you to individually boost and attenuate (cut) each of two frequency
ranges (high and low). Its frequency response is utterly unlike that of a conventional EQ,
producing a unique character that is distinctive of this model. The input/output circuits and
vacuum tubes produce a tonal character that is highly musical and well-balanced.
1 IN switch
Turns the processor on or off.
When the switch is off, the signal will bypass the filter section, but pass through the
input/output transformer and amp circuits.
2 LOW FREQUENCY knob
Sets the frequency of the low range filter.
3 (LOW) BOOST knob
Sets the amount of boost applied to the frequency band specified by the LOW
FREQUENCY knob.
4 (LOW) ATTEN knob
Sets the amount of attenuation applied to the frequency band specified by the LOW
FREQUENCY knob.
5 BAND WIDTH knob
Sets the width of the frequency band controlled by the high range filter.
As you rotate the knob toward the right (Broad), the band will become wider and the
peak level will decrease. This affects only the response of the boost.
6 HIGH FREQUENCY knob
Sets the frequency of the high range filter. This affects only the response of the boost.
2134
2 61
3 4 5 7 8 9
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
167
7 (HIGH) BOOST knob
Sets the amount of boost applied to the frequency band specified by the HIGH
FREQUENCY knob.
8 (HIGH) ATTEN knob
Sets the amount of attenuation applied to the frequency band specified by the ATTEN
SEL knob.
9 (HIGH) ATTEN SEL knob
Switches the frequency region attenuated by the ATTEN knob.
Dynamic EQ
Dynamic EQ is a newly-developed equalizer that does not emulate any specific model of
equalizer. The sidechain has a filter that extracts the same frequency band as the EQ. This
allows you to apply EQ in the same way as you might apply a compressor or expander to a
specific frequency region, causing the EQ gain to vary dynamically only when a specific
frequency region of the input signal becomes too high or too low. For example you could use
this on a vocal sound as a de-esser, so that EQ is applied to a specific frequency band only
when sibilance or high-frequency consonants reach an unpleasant level, thus preserving a
natural sound that does not impair the original tonal character. Two full-band Dynamic EQs
are provided, enabling you to process a wide range of audio sources.
1 BAND ON/OFF button
Turns each band on or off.
2 SIDECHAIN CUE button
Turn this button on to monitor the sidechain signal sent to the CUE bus. At this time,
the graph indicates the response of the sidechain filters.
3 SIDECHAIN LISTEN button
Turn this button on to output the sidechain signal (linked to the dynamics) to the bus
(such as a STEREO bus or MIX/MATRIX bus) to which the insert channel signal is sent.
At this time, the graph indicates the response of the sidechain filters.
4 FILTER TYPE buttons
Switch the type of the main bus equalizers and sidechain filters. Main bus EQ and
sidechain filter will link as follows:
5 FREQUENCY knob
Sets the frequency band that will be controlled by the equalizer and sidechain filter.
6 Q knob
Sets the Q value (steepness) of the equalizer and sidechain filter.
As you rotate this knob clockwise, the frequency range to which the equalizer or
sidechain filter is applied will become wider.
7 THRESHOLD knob
Specifies the threshold at which the processor will begin taking effect.
8 RATIO knob
Sets the boost/cut ratio relative to the input signal.
Rotating the knob clockwise will set the ratio for boost, and counter-clockwise for cut.
Fully rotating the knob in either direction will create the maximum effect.
9 ATTACK/RELEASE buttons
Enable you to select one of the three settings as the attack/release time for compression
or boost.
Select FAST for a faster attack and faster release. Select SLOW for a faster attack and
slower release. Select AUTO to automatically adjust the attack/release time depending
on the frequency ranges.
0 MODE buttons
Specify whether the processor is triggered when the sidechain signal level exceeds the
threshold value (ABOVE), or when the level does not reach the threshold value (BELOW).
A EQ GAIN meter
Indicates the dynamically-changing EQ gain.
82A
4
3
1
9
0
6
5
7B
C
FILTER TYPE
(Low Shelf) (Bell) (Hi Shelf)
Main EQ Low Shelf Bell Hi Shelf
Sidechain filter LPF BPF HPF
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
168
B THRESHOLD meter
Indicates the sidechain signal level in relation to the threshold level.
C Graph area
Displays the equalizer response.
In most cases, this area displays the reference EQ graph that indicates the frequency and
intensity, and the dynamic EQ graph that indicates the dynamically-changing EQ
responses.
If SIDECHAIN CUE or SIDECHAIN LISTEN is on, this area displays the sidechain filter
response.
Buss Comp 369
Buss Comp 369 emulates a standard bus compressor that has been used in recording studios
and broadcasting stations since the 1980s. It produces a smooth and natural compression
that does not interfere with the expression in the source signal, in contrast with the aggressive
compression of the U76. Buss Comp 369 includes both a compressor and a limiter. You can
use both functions individually or in combination, according to your needs. Further, the rich
overtones generated by the audio transformers on the input/output circuits and the discrete
Class A amplifier add depth and unity to the sound quality.
STEREO mounting
DUAL mounting
Dynamic EQ graph
Reference EQ graph
Sidechain filter graph
31
8>ABC
42567
1
9>ABC
43567
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
169
1 INPUT ADJUST
Used to adjust the input gain. However, the output gain is linked to change in the
opposite direction, to prevent changes in pass-through volume (the volume when
COMP IN and LIMIT IN are off). For example, if INPUT ADJUST is +5dB, the input gain
is +5dB and the output gain is -5dB.
See below for more information about how to use INPUT ADJUST.
If the level of the input signal sent to effects is too low to reach the threshold, increase
the input gain.
Adjust the sound quality by changing the input level sent to the input circuitry (audio
transformer and Class A amplifier).
INPUT ADJUST structure
2 LINK (STEREO mounting)
Stereo link on/off
3 COMP IN
Compressor on/off
4 COMP THRESHOLD
Compressor threshold. However, the changing value is linked to INPUT ADJUST.
5 COMP RECOVERY
Compressor release time. The release times for a1 (auto 1) and a2 (auto 2) change
automatically. a1: Changes automatically between 100 ms and 2 sec. a2: Changes
automatically between 50 ms and 5 sec.
6 COMP GAIN
Compressor make-up gain. Applied before the limiter.
7 COMP RATIO
Compressor ratio
8 METER SELECT (STEREO mounting)
Selects the signal source for the meter. You can select from IN (input level), GR (gain
reduction), and OUT (output level). When the source is switched, the design of the
meter also switches as follows: VU/GR/VU.
WhenMETER” is IN
When METER” is GR
dBFSdBFS
COMP THRESHOLD LIMIT THRESHOLD
Buss Comp 369
COMPRESSOR/LIMITER SECTION
INPUT
CIRCUIT
OUTPUT
CIRCUIT
OUTPUT GAININPUT GAIN
INPUT ADJUST
COMPRESSOR LIMITER
OUT
OUT
IN IN
Since there are substantial changes in threshold, the changing display values are
linked. However, the internal conditions of the COMPRESSOR/LIMITER
SECTION do not actually change.
Linked in reverse
8
8
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
170
When METER” is OUT
9 VU SELECT (DUAL mounting)
Selects the signal source for the VU meter. You can select from input level or output level.
0 LIMIT IN
Limiter on/off
A LIMIT ATTACK
Limiter attack time. FAST: 2ms, SLOW: 4ms
B LIMIT THRESHOLD
Limiter threshold. However, the changing value is linked to INPUT ADJUST.
C LIMIT RECOVERY
Limiter release time. The release times for a1 (auto 1) and a2 (auto 2) change
automatically. a1: Changes automatically between 100 ms and 2 sec. a2: Changes
automatically between 50 ms and 5 sec.
MBC4
This high-quality four-band compressor utilizes VCM technology and features a GUI that
offers operability and visibility. All of the advantages of the musical behavior of analog
compressors have been built into the gain reduction circuitry of the MBC4. This allows smooth
control of dynamics while keeping the sound image. You can also use the graphical display
to visually manipulate the sound image.
1 GAIN LINE
This horizontal red line indicates the GAIN parameter for each band.
2 MAXIMUM GR GUIDELINE
This horizontal orange line is a guideline for maximum gain reduction. This is only a
guideline, and not a strict limitation for maximum gain reduction.
3 GR ZONE
This red area changes according to the amount of gain reduction for each band.
4 CROSSOVER LINE
These vertical lines indicate the CROSSOVER parameters for each band.
5 CROSSOVER ZONE
These areas, in the color of the band, change according to the CROSSOVER parameter
for each band.
8
9
8
4123 756
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
171
6 CROSSOVER RANGE
This horizontal bar for the band color indicates the range for the CROSSOVER parameter
for each band.
7 CROSSOVER BAND WIDTH
This horizontal bar for the band color changes according to the CROSSOVER parameter
for each band.
8 INPUT meter
Indicates the level of the input signal.
One meter appears in DUAL, while two meters appear in STEREO.
9 OUTPUT meter
Indicates the level of the output signal.
One meter appears in DUAL, while two meters appear in STEREO.
1 GAIN
Adjust the output gain for each band.
2 THRESH
Adjusts the threshold at which compression starts to be applied for each band. This
value is also indicated by a red marker in the
0 INPUT meter.
3 RATIO
Adjusts the compression ratio for each band.
4 ATTACK
Adjusts the compressor’s attack time for each band.
5 RELEASE
Adjusts the compressor’s release time for each band.
6 LINK knob
Links and adjusts the four bands for the selected parameter. However, if a parameter in
any frequency region reaches its maximum or minimum value, the link operation is
disabled. Parameters that can be linked and adjusted are displayed in band colors as
shown below.
7 CROSSOVER
Adjusts the crossover frequency when splitting the frequency range into multiple bands.
8 CUE button
Cue-monitors the corresponding band output for each band. When the CUE button is
on, the button changes to the color shown below.
If the IN button is off, the uncompressed sound is cue-monitored. The CUE buttons for
multiple bands can be turned on at the same time.
9 MASTER GAIN knob
Adjusts the gain for the final output signal.
0 INPUT meter
Indicates the input level for the audio signals sent to each band.
A KNEE knob
Adjusts the compressor’s knee.
B IN button
Turns each band on or off. When this button is off, the band color for the selected area
changes to gray as shown below.
9
8
7
B
A
D
>
C
6
4
3
2
1
5
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
V5 Reference Manual
172
Also, when this button is off, the COMPRESSOR field for the selected band turns gray.
You can adjust each parameter even when this button is off.
C FLAVOUR button
Switches the type of compressor between accurate VCA operation and natural OPTO
operation.
D HARMONICS button
Switches on/off the analog circuitry that emulates musical overtones.
Using the graphic EQ, parametric EQ, effect, and
Premium Rack libraries
GEQ/PEQ library
Use the “GEQ library” or “PEQ library” to store and recall GEQ and PEQ settings. All GEQ
and PEQ units used in the CL series console can use this GEQ library or PEQ library.
Although are two types, 31BandGEQ and Flex15GEQ in the GEQ library, you are free to recall
items between differing types. However, only 31BandGEQ settings that use less than fifteen
bands can be recalled to a Flex15GEQ.
200 items can be recalled from the library. Number 000 is a read-only preset, and the
remaining library numbers can be freely read or written.
To recall an item from the GEQ library, press the LIBRARY button located at the top of the
GEQ EDIT window.
Similarly, to recall an item from the PEQ library, press the LIBRARY button located at the top
of the PEQ EDIT window.
NOTE
Store and recall operations are performed on individual GEQ units. For one rack, you can store
and recall two Flex15GEQ or 8BandPEQ units independently as A and B.
To access the GEQ EDIT window or the PEQ EDIT window, press the rack container in the GEQ
field.
Effect library
Use the “Effect library” to store and recall effect settings. 199 items can be recalled from the
effect library. Library items 1-27 are read-only presets, and correspond to effect types 1-27
respectively. The remaining library numbers can be freely read or written.
To recall an item from the effect library, press the LIBRARY button located at the top of the
EFFECT EDIT window.
Premium Rack library
You can use the Premium Rack library to store and recall Premium Rack settings. The library
contains 101 items (from #000 through #100). Item #000 is a preset. All library items other
than #000 can be freely read and written.
To recall an item from the Premium Rack library, press the LIBRARY button located at the top
of the window for the corresponding type.
I/O devices and external head amps
V5 Reference Manual
173
I/O devices and external head amps
This chapter explains how to use an I/O device or an external head amp that is connected to
the CL series console. Before you proceed, use DANTE SETUP to specify the I/O devices
that will be mounted. For details, refer to “Mounting an I/O device on the Dante audio network
(page 263).
Using an I/O device
CL series consoles enable you to remotely control channel parameters of an I/O device (such
as an R series product) connected to the Dante connector.
I/O device patching
Heres how an I/O device connected to the Dante connector can be patched to the Dante
audio network.
I/O DEVICE screen (DANTE PATCH page)
1 I/O device list
This shows the ID number and model name of the I/O devices.
Press here to access the OUTPUT PATCH window, where you can specify patching from
the console’s output ports to the I/O devices. If a previously set-up device does not
currently exist on the Dante audio network, a yellow VIRTUAL” indicator is shown at
the lower left of that device. If devices on the network belong to different DEVICE TYPEs
but share the same ID, a redCONFLICT” indicator will appear to the left, below the
device. If multiple devices share the same ID, a yellowDUPLICATE” indicator will
appear to the right, below the device.
2 DANTE SETUP button
Press this button to open the DANTE SETUP window, in which you can make settings
for the audio network.
3 DANTE INPUT PATCH button
Press this button to open the DANTE INPUT PATCH window, in which you can select the
64 channels that will be input from the I/O device to the console.
4 OUTPUT PORT SETUP button
Press this button to access the PATCH VIEW 1 tab of the OUTPUT PORT window, where
you can choose the 64 channels that will be output from the console’s output ports to
I/O devices.
STEP
1. Connecting CL series consoles and I/O devices
2. In the Function Access Area, press the I/O DEVICE button.
3. Press the DANTE PATCH tab in the upper part of the I/O DEVICE screen.
4. Press the DANTE INPUT PATCH button in the I/O DEVICE screen (DANTE PATCH
page).
5. Press the AUTO SETUP button.
If you want to edit individual patches, press the port select button.
6. Press the device in the I/O DEVICE screen (DANTE PATCH page).
7. Press the port select button in the OUTPUT PATCH window.
8. In the PORT SELECT screen, select the output port.
1
2
3
4
I/O devices and external head amps
V5 Reference Manual
174
DANTE INPUT PATCH window
Displayed when you press the DANTE INPUT PATCH button in the I/O DEVICE screen
(DANTE PATCH page). Specify the 64 channels that will be input from the I/O devices to the
console.
1 LIBRARY button
Enables you to store or recall the DANTE INPUT PATCH settings to or from the library.
You can store ten sets of settings in the library.
NOTE
If you recall data whose I/O device registration state differs from the current state, patching to
devices not registered in the I/O device list will be kept in its current state, and will not be
recalled. (The settings are recalled for an R unit, or an external CL series console.)
Similarly, if the UNIT ID is different than when the data was stored, the settings will not be
recalled; the current state will be maintained.
2 AUTO SETUP button
The current I/O device connection status will be ascertained, and input patching to the
console will be performed automatically according to the order in which they are
registered in the I/O device list.
When you press this button, a confirmation popup dialog will appear, asking you to
confirm the execution of auto patching. Press the OK button to execute auto patching.
Otherwise, press CANCEL to return to the previous screen.
3 Port select buttons
Press this button to open the PORT SELECT window.
“Dante Device ID number (hexadecimal) and channel number
(decimal)” are shown in the upper row on the button.
The first eight characters of the channel label (Dante Audio Channel
Label) for each port are shown in the lower row on the button.
When a patch establishes an audio connection via AES67, “AES67” is displayed on the
port selection buttons, etc.
If no patch has been assigned, the upper row will indicate---” and the lower row will
indicate nothing.
NOTE
If you’ve connected a device other than an I/O device supported by the CL series, the upper
line of the button will show the first four letters of the Device Label, a dash “-” , and the channel
number (decimal).
If a CL series console is mounted, the display for the upper row of buttons will be “CL#X” (where
X is the ID number of the mounted CL unit).
If no Dante Audio Channel Label has been specified, a value equal to the channel number will
be displayed in the lower row.
You can set the Dante Audio Channel Label using Audinate “Dante Controller” software. For the
latest information, refer to the Yamaha pro audio website.
https://www.yamaha.com/proaudio/
The Audinate “Dante Controller” software is required to use the CL console in AES67 mode.
Routing via AES67 is possible only by using Dante Controller.
Channels with patches that use AES67 offline will synchronize with the patch settings that are
saved on the target device when connected with the device.
1 2
3
I/O devices and external head amps
V5 Reference Manual
175
PORT SELECT window
Displayed when you press the port select button in the DANTE INPUT PATCH window or
OUTPUT PATCH window. When you change a patch, select the I/O port.
1 Category select list
Enables you to select the I/O device containing the input port that you want to assign.
2 Port select buttons
Select the input port.
3 CLOSE button
Completes the settings and closes the window.
OUTPUT PATCH window
Displayed when you press the device in the I/O DEVICE screen (DANTE PATCH page). Set
the output patch.
1 Port select buttons
Press one of the buttons to open the PORT SELECT popup window.
Remotely controlling an R series unit
This section explains how to remotely control an R series unit that’s connected to the Dante
connector.
2
31
STEP
1. In the upper part of the I/O DEVICE screen, press the I/O tab to display the I/O
DEVICE screen (I/O page).
2. Press the rack in which the I/O device that has head amp functionality is mounted.
3. Open the I/O DEVICE HA screen to remotely control the head amp of the I/O device.
4. To remotely control a head amp from an input channel, press a knob in the
SELECTED CHANNEL section to display the SELECTED CHANNEL VIEW screen.
5. Press the GAIN/PATCH field of the channel you want to adjust. The GAIN/PATCH
window will appear.
6. Control the head amp of the I/O device in the GAIN/PATCH window.
7. When you have finished making settings, press the “x” symbol to close the window.
8. Press the rack in which the I/O device on the OUTPUT side is mounted.
9. Set the output port on the OUTPUT PATCH window, as necessary.
Refer to step 7 in I/O device patching” (page 173).
1
I/O devices and external head amps
V5 Reference Manual
176
I/O DEVICE screen (I/O page)
1 Display switch buttons
Press one of these buttons to view the corresponding I/O device. If you press and hold
down this button, all LEDs of the corresponding I/O device will blink.
For more information about VIRTUAL/CONFLICT/DUPLICATE displayed below this
button, refer to
1 on P.173, I/O device list”.
When the CONSOLE ID select button is set to OFF in the DANTE SETUP screen, the NOT
CTRL indicator appears below the Display switch button of each device.
The NOT CTRL indicator also appears on the icons of the DANTE PATCH screen.
2 ID/Model name display
This shows the ID number, model name, and version of the I/O device.
If the WITH RECALL button is turned ON in the REMOTE HA SELECT screen, w/RECALL”
is displayed. If the +48V MASTER switch for the mounted device is turned ON,+48V
MASTER” is displayed.
3 DANTE SETUP button
Press this button to open the DANTE SETUP window, in which you can make settings
for the audio network.
4 SYSTEM/SYNC indicators
Error, warning, and information messages are displayed. Refer to the list (page 284) for
detailed information about messages.
Now displays error and information icons to quickly check the status of the system and
synchronization.
When touching these icons, the details of errors and information are displayed at the
bottom of the display.
When an error occurs in SYSTEM or SYNC, the Error icon will appear at the top of right
side on the Display switch button.
5 REMOTE ONLY button
This button is displayed for I/O devices that can be operated on the device itself.
Set this button to ON to disable panel operation of the I/O device unit, making only
remote controls available. The operation (selecting ON or OFF) of the REMOTE ONLY
button is available only from a console the WITH RECALL button set to ON in the
REMOTE HA SELECT screen.
6 REMOTE CONTROL STATUS indicator
Appears in all remote control supported devices and displays the settings of the remote
control.
7 OUTPUT PATCH button
Appears when selecting a device (for I/O DEVICE) having a large number of channels.
Touch to open the OUTPUT PATCH window.
1 2
4
3
5
6
7
Error
Information
I/O devices and external head amps
V5 Reference Manual
177
HA display
This shows the HA settings of the I/O device. Press this area to open the I/O DEVICE HA
window, in which you can make detailed head amp settings.
If you press the [SEL] key of an input channel, the corresponding port will light. (It does not
light for external CL series consoles.)
8 Analog GAIN knob
Indicates the analog gain setting. This screen is only for display; the value cannot be
edited.
9 +48V indicator
Indicates the phantom power (+48V) on/off status for each port.
0 OVER indicator
Warns you when the input signal is clipping.
A HPF indicator
Indicates the high-pass filter on or off status for each port.
INPUT display
This shows the input settings of I/O devices not assigned to REMOTE HA ASSIGN.
If you press the [SEL] key of an input channel, the corresponding port will light. (It does not
light for external CL series consoles.)
OUTPUT display
This shows the output settings of the I/O device. Press here to access the OUTPUT PATCH
window, where you can make output port settings for the I/O device.
If you press the [SEL] key of an output channel, the corresponding port will light. (It does not
light for external CL series consoles.)
RMio64-D display
Displays the RMio64-D panel. You can press the buttons to change settings.
1 MADI SRC ON indicator
MADI SRC ON button
Switches the SRC (Sampling Rate Converter) on and off.
2 MADI SRC WCLK IN indicator
MADI SRC WCLK IN button
Use this button to select whether to use (indicator on) or not use (indicator off) the word
clock input from the MADI WCLK IN FOR SRC jack on the rear panel of the RMio64-D
as a standard clock for SRC.
3 MADI INPUT RATE Fs 44.1kHz indicator
MADI INPUT RATE Fs 48kHz indicator
Automatically detect and indicate whether the MADI input signal is 44.1 kHz or 48 kHz.
Both indicators remain off if there is no valid MADI input signal.
4 MADI INPUT RATE 1Fs indicator
MADI INPUT RATE 2Fs indicator
MADI INPUT RATE 4Fs indicator
MADI INPUT RATE 1Fs/2Fs/4Fs button
Select either 1Fs (1x), 2Fs (2x), or 4Fs (4x), based on the MADI input frequency. For
example, if the MADI input signal is 192 kHz (4x 48 kHz), confirm that the MADI INPUT
RATE Fs 48kHz indicator is on and then select4Fs”.
NOTE
When “2Fs” is selected, the unit automatically detects the frame frequency (48 kHz/96 kHz) of
the MADI input signal.
9
A
8
0
5421 3
6
9
87
I/O devices and external head amps
V5 Reference Manual
178
5 MADI STATUS INPUT status
MADI STATUS OUTPUT status
Display information regarding the MADI input and output signals (frame frequency/
number of channels).
6 WORD CLOCK WCLK IN indicator
WORD CLOCK MADI indicator
WORD CLOCK DANTE indicator
WORD CLOCK WCLK IN/MADI/DANTE buttons
Used to select the word clock source.
7 WORD CLOCK Fs indicator
Indicates the word clock frequency at which the unit is operating. Flashes when not
synchronized.
8 EXTERNAL CONTROL indicator
This indicator comes on when there is a valid parameter that can be operated only
externally by remote control.
Refer to Remote Control” in the RMio64-D Owner’s Manual for details about
parameters that can be operated by remote control.
9 OUTPUT PATCH button
Press this button to access the OUTPUT PATCH window, where you can make output
port settings for RMio64-D.
RSio64-D display
1
CARD NAME
This indicates the names of the cards installed in slots 1 to 4. If nothing is installed,
“----” will appear.
2 IN/OUT PORT
This indicates the number of input and output ports for the cards installed in slots 1 to
4. If no card is installed, “--” will appear.
WCLK IN
Uses the word clock signal being input from the WORD CLOCK IN connector on
the rear panel of RMio64-D. The indicators flash when there is no valid word clock
input.
MADI
Uses the word clock of the MADI input signal. The indicators flash when there is no
valid word clock input.
DANTE Uses the word clock of the Dante network.
156243C
AB78 9 0
I/O devices and external head amps
V5 Reference Manual
179
3 SLOT 1 - 4 LOCK indicators
This indicates the word clock status for slots 1 to 4. If the word clock is operating
normally, this indicator will be green.
4 SLOT 1 - 4 SRC indicators
Indicate the Sampling Rate Converter (SRC) status for slots 1 to 4.
NOTE
Use the SRC WCLK DIP switches on the RSio64-D to set the SRC clock sent to the Mini-YGDAI
card inserted in the slot.
5 SLOT 1 to 4 SRC buttons
Used to turn SRC on/off at both IN and OUT for each slot.
6 WCLK indicator
If the card’s internal sampling rate converter function is enabled when an MY8-AE96S
mini-YGDAI card is inserted into the RSio64-D,CARD is displayed. If the cards internal
sampling rate converter function is disabled, “SLOT” is displayed.
7 WORD CLOCK select button
Used to select the word clock source for the RSio64-D.
WORD CLOCK WCLK IN indicator
WORD CLOCK SLOT1 1/2 indicator
WORD CLOCK DANTE indicator
Indicates the word clock source status for the RSio64-D.
*1 When flashing, Dante word clock
*3
input/output is used.
*2 If you are using MY8-AEB, set the AERSVD switch for the card to RSVD.
*3 If you make changes to the frequency of the Dante word clock, use Dante Controller.
8 CURRENT PATTERN button
If you press this button, the currently selected routing pattern on the RSio64-D is
displayed. If you switch the routing pattern on the RSio64-D, it will be applied in 3
seconds.
Off There is no card in the slot. Or, an unsupported card is in the slot.
Green (On)
LOCK
Indicates that a clock synchronized with the clock source selected with the
[WORD CLOCK] select key is being input from the card. If an external device is
connected to the corresponding slot, input/output is occurring properly between
that device and the RSio64-D. If the sampling frequency is close, this status may
be displayed even if not synchronized.
Green
(Flashing)
SYNC
ERROR
A valid clock is being input from the card, but is not synchronized with the clock
source selected with the [WORD CLOCK] select key. If an external device is
connected to the corresponding slot, input/output cannot occur correctly between
that device and the RSio64-D. Turn SRC ON for correct input/output.
Red (On)
UNLOCK
A valid clock is not being input from the card. If an external device is connected to
the corresponding slot, input/output cannot occur correctly between that device
and the RSio64-D.
Red
(Flashing)
WRONG
WORD
CLOCK
The frequency of the clock source selected with the [WORD CLOCK] select key is
outside of the operating frequency range for the card inserted in the slot. Either
set the frequency of the clock source within the operating range for the card, or
turn [SRC] ON. For an analog card, if you turn [SRC] ON, the frequency is set to
the 48kHz built into the RSio64-D.
Off SRC is off.
Green (On)
SRC is on, and the clock selected with the SRC WCLK DIP switches on the
RSio64-D is being input correctly.
Red (On)
SRC is on, but an appropriate clock is not being input. The clock selected with the
SRC WCLK DIP switches on the RSio64-D is either not being input or is not
within the operating range. Either turn SRC off, or change the DIP switch settings.
WCLK IN
On when using the word clock signal being input from the WORD CLOCK
IN connector on the rear panel of the RSio64-D. Flashes
*1
if there is no
valid word clock input.
SLOT1 1/2
On when using the word clock for channels 1/2 of slot 1 for the RSio64-D.
Flashes
*1
if there is no valid word clock input. When using MY8-AEB
*2
, the
word clock for channels 7/8 is used.
DANTE
On when using the word clock for the Dante network
*3
. (If there is no valid
Dante signal input, the internal Dante module will generate a clock.)
I/O devices and external head amps
V5 Reference Manual
180
9 USER PATTERN button
Press this button to open the window for setting the audio routing user pattern in the
RSio64-D. Patch to the desired output ports of the slots and Dante.
NOTE
Patching from one slot to another is also available (including patching to the same slot). However,
you cannot patch from Dante to Dante.
0 OUTPUT PATCH button
Press this button to open the OUTPUT PATCH window, in which you can set the 64
Dante channels that will be output from the console to the RSio64-D.
A POWER INT indicator
Indicates the status of the AC IN power supply for the RSio64-D. If the power switch is
off, no power is supplied to AC IN and the indicator remains off.
B POWER EXT indicator
Indicates the status of the EXT DC INPUT power supply for the RSio64-D. If the power
supply is on, this indicator will be on. This indicator is not affected by the status of the
power switch.
C Control status indicator
Indicates the control status of the device.
Third-party equipment’s HA control function
It is possible to control supported third-party equipment’s head amps (HA) from the console.
You can control HA by registering supported devices in the DANTE SETUP window.
NOTE
While in PREVIEW mode, changes made to HA parameters from the console are not applied to
the device.
You can turn “WITH RECALL” on and off in the REMOTE HA ASSIGN window.
You can store/recall scene libraries and save/load files.
You can register up to 8 devices, including R series units. You can also register a device that
has the same UNIT ID as a device that is already registered, including R series units. You can
adjust HA parameters in advance, even when a connection is not established with the device
to be controlled.
You can control the following parameters.
1 HA phantom power (+48V) on/off
2 HA gain
3 Head amp HPF on/off
Searching for device to be controlled
Connecting to device
Synchronizing with device
Device can be controlled
Found device to be controlled, but connection refused
1
2
3
I/O devices and external head amps
V5 Reference Manual
181
NOTE
The indicator on the right side of the rack indicates the control status of the device.
You can perform the following operations from input channels patched to the target device:
Store/recall input channel library
Channel jobs (channel link, etc.)
HA controls at user level (only when operating HA from an input channel)
AG-DG LINK
NOTE
You cannot perform this operation on devices that do not support Gain Compensation.
I/O DEVICE HA window
Displayed when you press the rack in which the I/O device on the head amp side is mounted.
In this window, you can remotely control the head amp of the I/O device from the CL series
console by using the on-screen knobs and buttons or the multifunction knobs.
1 +48V MASTER
Indicates the on/off status of the I/O device’s master phantom power. (Switching this on
or off is performed on the I/O device itself.)
2 +48V button
These switch phantom power on/off for each channel.
3 GAIN knob
Indicates the gain of the head amp on the I/O device. To adjust the value, press the knob
to select it, and use the multifunction knobs. The level meter located at the immediate
right of the knob indicates the input level for the corresponding port.
NOTE
For devices with a wider setting range than the CL series, since some values cannot be set from
the CL series. Likewise, if the value set on the connected device side is outside the CL series
setting range, it will be displayed as an approximate value or limit value.
4 GC button
Switches on or off the Gain Compensation function that maintains a consistent signal
level on the audio network.
5 FREQUENCY knob/HPF button
These controllers switch on or off the high-pass filter built into the head amp of the I/O
device, and adjust its cutoff frequency. If you press the FREQUENCY knob to select it,
you will be able to adjust it using the corresponding multifunction knob.
NOTE
For devices that differ in how the setting value changes from the CL series, the cutoff frequency
will be set as an approximate value.
Searching for device to be controlled
Connecting to device
Synchronizing with device
Device can be controlled
Found device to be controlled, but connection
refused
2
3
4
5
6
7
8
1
I/O devices and external head amps
V5 Reference Manual
182
6 Displayed port switch tabs
These tabs switch the port that is displayed in the I/O DEVICE HA window.
7 GC ALL ON button/GC ALL OFF button
Switch Gain Compensation on or off for all input channels simultaneously.
8 GC indicator
Indicates the fixed gain value output to the audio network if the Gain Compensation
function is turned on.
Remotely controlling from the input channels
To remotely control the I/O devices head amp from an input channel of the CL series console,
operate the GAIN/PATCH window for the channel for which you want to control.
Remotely controlling an amp
This section explains how to remotely control an amp unit that’s connected to the Dante
connector.
I/O DEVICE screen (AMP page)
1 Display switch buttons
Press one of these buttons to view the corresponding I/O device.
For more information about VIRTUAL/CONFLICT/DUPLICATE displayed below this
button, refer to
1 on P.173, I/O device list”.
2 ID/Model name display
This shows the ID number, model name, and version of the I/O device.
STEP
1. Press the AMP tab in the upper part of the I/O DEVICE screen.
2. Press the I/O device displayed on the I/O DEVICE screen (AMP page).
3. Set the output port on the OUTPUT PATCH window, as necessary.
Refer to step 7 in I/O device patching” (page 173).
1 2
3
I/O devices and external head amps
V5 Reference Manual
183
3 DANTE SETUP button
Press this button to open the DANTE SETUP window, in which you can make settings
for the audio network.
Remotely controlling WIRELESS unit
This section explains how to remotely control a WIRELESS unit that’s connected to the Dante
connector.
NOTE
For supported devices and compatible versions, refer to Yamaha Pro Audio website.
https://www.yamaha.com/proaudio/
I/O DEVICE screen (WIRELESS page)
1 Display switch buttons
Press one of these buttons to view the corresponding I/O device. If you press and hold
down this button, all LEDs of the corresponding I/O device will blink.
For more information about VIRTUAL/CONFLICT/DUPLICATE displayed below this
button, refer to
1 on P.173, I/O device list.”
2 ID/Model name display
This shows the ID number, model name, and version of the I/O device.
3 DANTE SETUP button
Press this button to open the DANTE SETUP window, in which you can make settings
for the audio network.
Wireless devices display
NOTE
Displayed contents and channels will be changed depending on the device.
1 Connection status indicator
Indicates the connection status with the wireless device.
The icon will be changed depending on the devices.
2 Channel name (transmitter)
Indicates the channel name that is set on the transmitter.
3 TX.GAIN/TX.ATT
Indicates the gain value for the transmitter. This window is only for display; the value
cannot be edited. The knob name is changed depending on the connected device.
STEP
1. Press the WIRELESS tab in the upper part of the I/O DEVICE screen.
2. Press the I/O device displayed in the I/O DEVICE screen (WIRELESS page).
1 2
3
2
1
5
3
4
7
8
9
>
A
6
I/O devices and external head amps
V5 Reference Manual
184
4 Channel name (receiver)
Indicates the channel name that is set on the receiver.
5 Frequency
Indicates the frequency that is currently set for the RF signal.
6 RX.LEVEL/RX.GAIN
Indicates the gain for the receiver. This window is only for display; the value cannot be
edited.
7 MUTE indicator
Indicates the mute status (on/off) of the audio signal for the receiver.
8 Signal quality meter
Displays the quality of the received RF signal. The vertical axis represents quality and the
horizontal axis represents time, and the display of connection status is updated every
second. If you move away from the transmitter, or the quality of the RF signal decreases
due to the influence of disturbing radio waves, the bar graph becomes lower. It displays
in purple for Shure devices, and in white for the other developer’s device.
9 RF (Radio Frequency) signal meter
Shows bars to indicate the level of the RF signal. An active antenna indicator is shown
on the right side. It indicates which antenna is enabled.
In the Diversity mode, both A and B are shown. In the Quadversity mode, the one with
the strongest level among A to D is shown.
NOTE
For details about the relationship between the number of bars and the actual strength of the RF
signal, refer to the manual from each developer.
0 Battery indicator
Shows bars to indicate the remaining battery power.
NOTE
For details about the relationship between number of bars and maximum operation time, refer to
the manual from each developer.
A Control status indicator
Indicates the control status of the device.
NOTE
When control on the receiver side is possible, the parameter values for the receiver are sent to
the console.
I/O DEVICE EDIT screen
This screen is displayed when you select the desired wireless device in the I/O DEVICE
screen (WIRELESS page). Here you can set the channel name and HA. You cannot set when
the device is offline. Note that when the device is online, the settings on the device are
applied.
NOTE
Displayed contents and channels will be changed depending on the device.
1 Connection status indicator
Indicates the connection status with the wireless device.
The icon will be changed depending on the devices.
2 Channel name button (transmitter)
Press this button to display the NAME screen for setting channel names on the
transmitter side. The number of characters that can be set varies depending on the
device.
Searching for device to be controlled
Connecting to device
Synchronizing with device
Device can be controlled
Found device to be controlled, but connection refused
B
1
2
3
4
5
6
7
8
9
0
A
C
I/O devices and external head amps
V5 Reference Manual
185
3 TX.GAIN knob/TX.ATT knob
Sets the gain value for the transmitter. To adjust the value, touch the screen, then press
the knob to select it, and use the multifunction knobs. The knob will not display when
the wireless device is not support this control.
4 TX.GAIN
Displays the gain value for the transmitter.
5 Channel name (receiver)
Press this button to display the NAME screen for setting channel names on the receiver
side. The number of characters that can be set varies depending on the device.
6 Frequency
Indicates the frequency that is currently set for the RF signal.
7 RX.LEVEL knob/RX.GAIN knob
Sets the gain value for the receiver. To adjust the value, touch the screen, then press the
knob to select it, and use the multifunction knobs. The level meter located at the
immediate right of the knob indicates the input level. The knob will not display when
the wireless device is not support this control.
8 MUTE button
Mutes the audio signal for the receiver.
9 Signal quality meter
Displays the quality of the received RF signal. The vertical axis represents quality and the
horizontal axis represents time, and the display of connection status is updated every
second. If you move away from the transmitter, or the quality of the RF signal decreases
due to the influence of disturbing radio waves, the bar graph becomes lower. It displays
in purple for Shure devices, and in white for the other developer’s device.
0 RF (Radio Frequency) signal meter
Shows bars to indicate the level of the RF signal. An active antenna indicator is shown
on the right side. It indicates which antenna is enabled.
In the Diversity mode, both A and B are shown. In the Quadversity mode, the one with
the strongest level among A to D is shown.
NOTE
For details about the relationship between the number of bars and the actual strength of the RF
signal, refer to the manual from each developer.
A Battery indicator
Shows bars to indicate the remaining battery power.
NOTE
For details about the relationship between number of bars and maximum operation time, refer to
the manual from each developer.
B Mode indicator
Indicates the mode status of the device such as Diversity mode or Quadversity mode.
When not activated, it shows “Diversity mode: off” or “Quadversity mode: off”
respectively.
C PORT ASSIGN tab
Select these tabs to switch between the windows that specify the ports where the actual
input signals are assigned.
I/O devices and external head amps
V5 Reference Manual
186
Example: Connecting the output of a Shure AXT400 to OMNI 1 on a CL console, and
assigning the signal to input channel 1.
Press the PORT ASSIGN button to open the PORT SELECT window. Select the port to
which the output from the AXT400 is connected (OMNI 1).
Access the GAIN/PATCH window.
Press the INPUT PORT button, and on the PORT SELECT window select the port to which
the output signal from the AXT400 is connected (OMNI 1).
I/O devices and external head amps
V5 Reference Manual
187
This assigns the output signal from the AXT400 to the input channel, and at the same
time allows you to control and monitor the level of the AXT400 from the input channel.
Precautions
If the target device is unmounted, the parameters on the console return to their default
values. If a new device is mounted and patched, that devices parameters are applied to the
console.
All port assignments for a rack are defeated only if the status of the rack is NO ASSIGN.
Regarding the control of each developer’s device, control parameters are not stored in
scenes and saved in console files.
For devices that can set both Dante Input Patch and Port Assign, if Dante Input Patch has
already been set, the Port Assign setting will be ignored.
Using an external head amp
If an I/O card (such as an MY16-ES64 card) supports the remote protocol of an external head
amp in the CLs slot, you will be able to remotely control from the CL console some parameters
of the external head amp (Yamaha SB168-ES or AD8HR), such as phantom power (+48V)
on/off status, gain, and HPF.
For details on the I/O card settings, refer to the Owner’s Manual for the I/O card.
Connecting the CL series console to an AD8HR
To remotely control the AD8HR from the CL series console, install an MY16-ES64
EtherSound card in Slot 1 on the CL unit, then use an Ethernet cable to connect the CL unit
to the NAI48-ES. Then, connect the HA REMOTE connector on the NAI48-ES to the HA
REMOTE 1 connector on the AD8HR using an RS422 D-sub 9-pin cable. This connection
enables you to remotely control the AD8HR from the CL series console.
To transmit audio signals (input to the AD8HR) to the CL series console, connect the DIGITAL
OUT A (or B) connector on the AD8HR to the AES/EBU connector on the NAI48-ES using a
D-sub 25-pin AES/EBU cable. Signals will be sent or received between the NAI48-ES and the
CL series console via the MY16-ES64 card.
Alternatively, you can use a “daisy chain” connection to remotely control multiple AD8HR units
simultaneously. To do this, connect the AD8HR’s HA REMOTE 2 connector to the second
AD8HRs HA REMOTE 1 connector. If you use the NAI48-ES, you can connect up to six
AD8HR units. In this case, to input AD8HRs audio signals into the CL series console, install
two MY16-EX cards on the CL unit since each slot on the CL unit accepts up to 16 channel
signals. Then, connect each two of the third and subsequent AD8HRs to each AES/EBU
connector using a D-sub 25-pin AES/EBU cable.
I/O devices and external head amps
V5 Reference Manual
188
Connecting the CL series console to an SB168-ES
To remotely control the SB168-ES from the CL series console, install an MY16-ES64
EtherSound card in Slot 1 of the CL, then use an Ethernet cable to connect the CL to the
SB168-ES. This connection enables you to remotely control the SB168-ES from the CL series
console.
Alternatively, you can use a daisy chain or ring connection and install two MY16-EX
expansion cards in the slots on the CL unit to remotely control up to three SB168-ES units
simultaneously.
NOTE
Remote control data will be received and transmitted only at Slot 1 of the CL series console.
Daisy chain network
CL5
AD8HR 1
NAI48-ES
AD8HR 2
AD8HR 3
MY16-EXMY16-EX MY16- ES64
DIGITAL OUT
A connector
DIGITAL OUT
A connector
DIGITAL
OUT A
connector
HA REMOTE connector
HA REMOTE 1 connector
HA REMOTE 2 connector
Up to six units
Audio signal
Remote signal
HA REMOTE 2 connector
HA REMOTE 2 connector
HA REMOTE 1 connector
HA REMOTE 1 connector
SB168-ES
SB168-ES
SB168-ES
MY16-
ES64
MY16-
EX
MY16-
EX
CL5
OUT
Audio signal
Remote signal
IN
OUT
IN
IN
OUT
I/O devices and external head amps
V5 Reference Manual
189
Ring connection
NOTE
Please refer to the SB168-ES Owner’s Manual for information on setting up the MY16-ES64/
MY16-EX cards and EtherSound network.
Remotely controlling an external head amp
An external head amp ( “external HA” ) connected via MY16-ES64 or NAI48-ES can be
remotely controlled from the CL series console. For details on how to connect a CL series
console with an external head amp, refer to “Using an external head amp” (page 187) and the
external head amp’s operating manual.
SB168-ES
SB168-ES
SB168-ES
CL5
MY16-
ES64
MY16-
EX
MY16-
EX
Audio signal
Remote signal
OUT
IN
OUT
IN
IN
OUT
OUT
STEP
1. Connect the CL series console to an external HA.
2. In the Function Access Area, press the RACK button.
3. Press the EXTERNAL HA tab in the upper part of the VIRTUAL RACK screen.
4. Press the EXTERNAL HA PORT SELECT button for the corresponding rack in the
VIRTUAL RACK screen (EXTERNAL HA page).
5. Use the PORT SELECT buttons in the EXTERNAL HA PORT SELECT window to select
the input ports to which the audio output of the external HA is connected.
6. Press the CLOSE button to close the EXTERNAL HA PORT SELECT window.
7. In the VIRTUAL RACK screen (EXTERNAL HA page), press the rack in which the
external HA you want to control is mounted.
8. Remotely control the external head amp in the EXTERNAL HA window.
VIRTUAL RACK screen
(EXTERNAL HA page)
I/O devices and external head amps
V5 Reference Manual
190
VIRTUAL RACK screen (EXTERNAL HA page)
1 EXTERNAL HA field
This displays the state of the connected external HA.
2 ID/Model name/+48V master
This displays information for the external HA mounted in the rack. The ID number is
automatically assigned in order of the connected devices from 1 to 6. This field also
enables you to view the on/off status of the master phantom power.
3 Virtual racks
These are up to six racks in which remotely controllable external HA units can be
mounted. If an external HA is mounted, this field will indicate the HA settings (GAIN
setting, and on/off status of the phantom power and HPF). Press a rack to open the
EXTERNAL HA window for that rack.
4 EXTERNAL HA PORT SELECT button
Press this button to display the HA PORT SELECT window, in which you can set the input
port for the external head amp mounted in the rack.
NOTE
If an external HA is connected to one of the slots on the CL series console, you must specify an
appropriate input port manually. If this is set incorrectly, the external HA will not be detected
correctly when you patch input ports to input channels.
5 VIEW switch buttons
Switch the virtual rack display between SB168-ES and AD8HR. Select the view that’s
appropriate for the connected device.
6 COMM PORT switch buttons
Specify whether the external HA connected to the slot will be controlled remotely. Select
SLOT1” if you want to remotely control the external HA.
EXTERNAL HA PORT SELECT window
Select the input port for the external head amp. Display this window by pressing the
EXTERNAL HA PORT SELECT button in the I/O DEVICE screen (EXTERNAL HA page).
1 PORT SELECT buttons
Specify the input ports to which the external HA is connected.
2 3 4
1
5 6
1
I/O devices and external head amps
V5 Reference Manual
191
EXTERNAL HA window
Remotely control the external head amp. Display this window by pressing the virtual rack in
the I/O DEVICE screen (EXTERNAL HA page).
1 +48V MASTER
If an external HA is connected, the master phantom power on/off status is shown here.
(The on/off setting is made on the external HA unit itself.)
2 +48V button
These switch phantom power on/off for each channel.
3 GAIN knob
These indicate the gain of the external HA. If you press and select the GAIN knob, you
can make adjustments to gain using multifunction knobs 1-8. The level meter located
at the immediate right of the knob indicates the input level for the corresponding port.
4 FREQUENCY knob/HPF button
These controllers switch on or off the high-pass filter built into the external HA, and
adjust its cutoff frequency. If you press the FREQUENCY knob to select it, you will be able
to adjust it using the corresponding multifunction knob.
5 Rack select tabs
These tabs switch the rack that is displayed in the EXTERNAL HA window.
NOTE
If you connect an additional AD8HR, the setting for this AD8HR will be used.
These knobs and buttons are displayed in the EXTERNAL HA window even if an AD8HR is not
connected, allowing you to create and store a scene even while the AD8HR is not connected.
Error messages related to the SB168-ES will not be displayed. In addition, you will be unable
to set the EtherSound parameters. Use AVS-ESMonitor for these functions.
Remotely controlling an external HA from the input channels on a CL
series console
You will be able to use the external HA in the same way as the head amp on an I/O device or
on the CL console. For details on the GAIN/PATCH window, refer to “HA (head amp) settings
(page 32).
2
3
5
1
4
STEP
1. Use the Bank Select keys in the Centralogic section to access the OVERVIEW screen
that includes the channel for the head amp that you want to control.
2. Press the HA/PHASE field of the channel whose external HA you want to adjust.
3. Press the PATCH button in the GAIN/PATCH window, and select the input port
assigned to the external HA.
4. Remotely control the external head amp in the GAIN/PATCH window.
OVERVIEW
screen
GAIN/PATCH window
MIDI
V5 Reference Manual
192
MIDI
This chapter explains how to transmit MIDI messages from an external device to the CL series
console to control the CL console’s parameters, and how to send out MIDI messages from the
CL console as you operate the unit.
The following illustration shows an example of connecting the MIDI IN/OUT connectors to
transmit and receive MIDI messages.
MIDI functionality on the CL series console
The CL series console can use MIDI to perform the following operations.
Program Change transmission and reception
When you execute a specific event (scene/effect library recall) on the CL series console, a
Program Change message (a number that is assigned to the event) can be transmitted to an
external device. Conversely, the corresponding event can be executed when a Program
Change message is received from an external device.
Control Change transmission and reception
When you execute a specific event (fader, knob, or key operation) on the CL series console,
the corresponding Control Change message can be transmitted to an external device.
Conversely, events can be executed when Control Change messages are received from an
external device. This allows you to record fader and key operations on a MIDI sequencer or
other external device, and play them back later.
Parameter Change (SysEx) transmission and reception
When specific events (fader, knob, or key operations, changes in system settings or user
settings) are executed, “Parameter Change” SysEx (system exclusive) messages can be
transmitted to an external device. Conversely, events can be executed when Parameter
Changes are received from an external device.
Using this capability, CL operations can be recorded and played back on a MIDI sequencer
or other external device. In addition, changes in system and user settings can be received and
executed by another CL console.
NOTE
As the port used for transmission and reception of MIDI messages, you can select either the rear
panel MIDI IN/OUT connectors or an I/O card installed in slot 1. All of the functionality described
in this section will be available on the port you select.
Basic MIDI settings
You can select the type of MIDI messages the CL series console will transmit and receive, the
MIDI port that will be used, and the MIDI channel.
NOTE
For details on Program Change operations, refer to the following section “Using program changes
to recall scenes and library items” (page 195).
For details on using Control Change messages, refer to “Using control changes to control
parameters” (page 197).
CL5
MIDI OUTMIDI IN MIDI OUTMIDI IN
External device
STEP
1. In the Function Access Area, press the SETUP button.
2. Press the MIDI/GPI button in the center of the SETUP screen.
3. Press the MIDI SETUP tab in the MIDI/GPI screen.
4. Press the port select button for transmission (Tx) or reception (Rx) in the MIDI
SETUP page.
5. In the MIDI SETUP window for port selection, select the port type and port number
that will transmit or receive MIDI messages, and press the OK button.
6. Press the channel select button in the MIDI SETUP page.
7. In the MIDI SETUP window for channel selection, select the channel that will
transmit or receive MIDI messages, and press the OK button.
8. In the MIDI SETUP page, turn transmission/reception on or off for each MIDI
message.
SETUP screen MIDI/GPI screen
(MIDI SETUP page)
MIDI
V5 Reference Manual
193
MIDI/GPI screen (MIDI SETUP page)
You can select the type of MIDI messages that will be transmitted and received, and choose
the port that will be used.
1 PORT/CH field
Enables you to select the port and MIDI channel that will be used to transmit and receive
MIDI messages.
Tx PORT/Tx CH..................... Press these buttons to open windows in which you can
respectively select a port and MIDI channel to transmit
MIDI messages.
Rx PORT/Rx CH.................... Press these buttons to open windows in which you can
respectively select a port and MIDI channel to receive
MIDI messages.
NOTE
When transmitting or receiving Parameter Changes, the channel number you specify here is used
as the device number (a number that identifies the transmitting or receiving unit).
2 PROGRAM CHANGE field
Enables you to switch MIDI Program Change message transmission and reception on or
off.
Tx ........................................... Switches program change transmission on/off.
Rx........................................... Switches program change reception on/off.
ECHO..................................... Switches on or off echo output of Program Change
messages. (If this function is on, Program Change
messages received from an external device will be
retransmitted without modification.)
3 PROGRAM CHANGE MODE field
Enables you to select the Program Change transmit/receive mode.
SINGLE.............. If this button is on, Program Changes will be transmitted and
received on a single MIDI channel (Single mode).
MULTI ................ If this button is on, program changes will be transmitted/received on
multiple MIDI channels (Multi mode).
OMNI.................. If this button is on, Program Changes on all MIDI channels will be
received in Single mode. Multi mode transmission/reception and
Single mode transmission are disabled.
BANK................. If this button is on, Bank Select messages can be transmitted and
received in Single mode. (Bank Select messages switch the group
of Program Change messages to be used.)
4 CONTROL CHANGE field
Enables you to switch MIDI Control Change message transmission and reception on or
off.
Tx....................... Switches control change transmission on/off.
Rx ...................... Switches control change reception on/off.
ECHO................. Switches on or off echo output of Control Change messages. (If this
function is on, Control Change messages received from an external
device will be retransmitted without modification.)
5 CONTROL CHANGE MODE field
This field enables you to select the Control Change transmission/reception mode.
NRPN button..... If this button is on, the CL mix parameters will be transmitted/
received as NRPN messages on one MIDI channel (NRPN mode).
TABLE button ... If this button is on, the CL mix parameters will be transmitted/
received as Control Change messages on one MIDI channel
(TABLE mode).
6 PARAMETER CHANGE field
Enables you to turn transmission/reception of SysEx (system exclusive) messages on or
off. (These are special messages used to control the parameter of the CL console.)
Tx....................... Switches parameter change transmission on/off.
Rx ...................... Switches parameter change reception on/off.
ECHO................. Switches on or off echo output of Parameter Change messages. (If
this function is on, Parameter Change messages received from an
external device will be retransmitted without modification.)
7 OTHER COMMAND field
Switches on or off echo output of other MIDI messages. (If this function is on, other
MIDI messages received from an external device will be retransmitted without
modification.)
1
2
4
6
7
3
5
MIDI
V5 Reference Manual
194
MIDI SETUP window (for port selection)
Here you can select the port that will be used to transmit and receive MIDI messages. This
window appears when you press the port select button for transmission (Tx) or reception (Rx)
in the PORT/CH field.
1 TERMINAL field
Enables you to select the port that will transmit or receive MIDI messages.
You can choose from the following items.
2 PORT NO. field
If you select SLOT 1 in the TERMINAL field, choose port number 1-8 in this field. (The
number of available ports will vary depending on the card that is installed.) The
currently-available card is valid only for port 1.
3 OK button
Confirms the settings and closes the window.
MIDI SETUP window (for channel selection)
This parameter row enables you to specify MIDI Channels for MIDI message transmission
and reception. This window appears when you press the channel select button in the PORT/
CH field.
1 CH field
Enables you to select CH1-CH16 as the channel that will transmit or receive MIDI
messages.
2 OK button
Confirms the settings and closes the window.
NONE No port will be used.
MIDI MIDI IN (Rx) and OUT (Tx) connectors on the rear panel
SLOT1
A card that supports serial transmission and is installed in Slot 1 on
the rear panel
1 2
3
1
2
MIDI
V5 Reference Manual
195
Using program changes to recall scenes and library
items
The CL series console lets you assign a specific event (scene recall or effect library recall) to
each Program Change number, so that when this event is executed on the CL console, a
Program Change message of the corresponding number will be transmitted to an external
device. Conversely, the corresponding event can be executed when a Program Change
message is received from an external device.
NOTE
Assignments to program numbers are maintained as settings for the entire system, rather than
for individual scenes.
MIDI/GPI screen (PROGRAM CHANGE page)
In the PROGRAM CHANGE page, you can specify how Program Changes will be transmitted
and received, and choose the event (scene recall or effect library recall) that will be assigned
to each program number.
1 PROGRAM CHANGE field
Switches Program Change transmission and reception on or off. This setting is linked
with the PROGRAM CHANGE section of the MIDI SETUP page.
Tx..................If this is on, the corresponding Program Change messages will be
transmitted when events on the list are executed.
Rx .................If this is on, the corresponding events will be executed when Program
Change messages are received.
ECHO............If this button is on, Program Change messages received from an
external device will be retransmitted without change.
2 PROGRAM CHANGE MODE field
Enables you to select the Program Change transmit/receive mode. This setting is linked
with the PROGRAM CHANGE MODE section of the MIDI SETUP page.
Multi mode (when the MULTI button is on):
Program changes of all MIDI channels will be transmitted and received. (The transmit/
receive channel specified in the MIDI SETUP page will be ignored.) When a Program
Change is received, the event assigned to the corresponding MIDI channel and program
number in the list will be executed.
When you execute a specific event on a CL series console, the Program Change of the
corresponding program number will be transmitted on the MIDI channel shown in the
list. (If an event is assigned to more than one program number on multiple MIDI
channels/multiple program numbers, only the lowest-numbered program number on
each MIDI channel will be transmitted.)
STEP
1. Connect the CL series console to an external device.
2. As described in “Basic MIDI settings” (page 192), select the ports and MIDI channels
that will be used to transmit/receive program changes.
3. Press the PROGRAM CHANGE tab in the MIDI/GPI screen.
4. In the PROGRAM CHANGE page, switch Program Change transmission/reception on
or off, select transmission/reception mode, and set echo output.
5. To change the event assignment for each program number, press the desired event
in the list and select an event type and the recall target.
MIDI/GPI screen
(PROGRAM CHANGE page)
1
4
5
6
2
3
MIDI
V5 Reference Manual
196
Single mode (when the SINGLE button is on):
Only Program Changes of the transmit (Tx) and receive (Rx) channels specified in the
MIDI SETUP page will be transmitted and received. When a program change on the Rx
channel is received, the event assigned to that program number of the corresponding
channel in the list will be executed.
When you execute the specified event on the CL series console, the Program Change of
the corresponding program number will be transmitted on the Tx channel shown in the
list. (If an event is assigned to more than one program number on the same channel,
the lowest-numbered program number will be transmitted.)
When the OMNI button is on in SINGLE mode:
Program changes of all MIDI channels will be received. However, regardless of the MIDI
channel that is received, the event assigned to the corresponding program number of
the Rx channel will be executed. Turning on the OMNI button will not change the
operation for Program Change transmission.
When the BANK button is on in SINGLE mode
The CH indication in the list will change to BANK (bank number), and Bank Select
(Control Change #0, #32) and Program Change messages can be transmitted and
received. This can be convenient if you want to control more than 128 events on a single
MIDI channel.
When Bank Select and then Program Change messages (in that order) are received on
the Rx channel, the event assigned to that bank number and program number in the
list will be executed.
When you execute a specific event on the CL series console, Bank Select and Program
Change messages for the bank number and program number assigned to that event will
be transmitted on the Tx channel. (If the same event is assigned more than once in the
list, the lowest-numbered bank number and program number will be transmitted.)
NOTE
The settings of the OMNI and BANK buttons are ignored in Multi mode.
If the BANK button is on and only a Program Change on an applicable MIDI channel is received,
the last-selected bank number will be used.
If the BANK button is on, the OMNI button can also be turned on at the same time. In this case,
Bank Select and Program Change messages of all MIDI channels will be received.
3 List
Shows the event (scene recall or library recall) assigned to each MIDI channel and MIDI
Program Change number. The list shows the following items.
CH/BANK...............If “CH” is shown, this column indicates the MIDI channel (1-16) on
which Program Changes are transmitted/received. If Program
Change transmission and reception is in Single mode and the
BANK button is on, this will be labeled “BANK,” and the numerical
value in this column will correspond to the bank number (1-128).
NO..........................Indicates the program number 1-128.
PROGRAM CHANGE EVENT
.........................Indicates the type/number/title of the event assigned to each
channel (bank number) or program number. Press an individual
event display area to access the MIDI PROGRAM CHANGE
window, in which you can select the event that you want to assign.
4 Scroll knob
Press this knob to scroll the list upward or downward using the multifunction knob.
5 CLEAR ALL button
Press this button to erase all events from the list.
6 INITIALIZE ALL button
Press this button to restore all event assignments on the list to their default state.
MIDI PROGRAM CHANGE window
You can specify the event assigned to each program number. Display this window by pressing
the list in the PROGRAM CHANGE page in the MIDI/GPI screen.
1 TYPE field
Enables you to select the type of event.
The following table lists the events you can select.
NO ASSIGN No assignment
SCENE Scene memory recall operations
EFFECT Effect library recall operations
PREMIUM RACK Recall operations for the corresponding Premium Rack library
1 2 3
4
MIDI
V5 Reference Manual
197
2 DESTINATION field
Enables you to select the scene or library item to recall. If EFFECT or PREMIUM RACK is
selected in the TYPE field, the rack number will be shown. If SCENE is selected, this will
indicate - - -, and is not used.
3 LIBRARY NUMBER/LIBRARY TITLE field
Enables you to choose the library that you want to recall.
If SCENE or EFFECT is selected in the TYPE field, the LIBRARY TITLE is shown. If PREMIUM
RACK is selected, the LIBRARY NUMBER is shown.
4 OK button
Confirms the settings and closes the window.
Using control changes to control parameters
You can use MIDI Control Change messages to control specified events (fader/knob
operations, [ON] key on/off operations etc.) on the CL series console. This capability can be
used to record fader and key operations on a MIDI sequencer or other external device, and
play back this data later.
You can use Control Changes to control events in either of the following two ways.
Using Control Changes
This method uses typical Control Changes (control numbers 1-31, 33-95, 102-119). You can
freely assign an event to each control number.
Using NRPN (Non Registered Parameter Number)
This method uses a special type of Control Change messages called NRPN.
NRPN uses Control Change numbers 99 and 98 to specify the MSB (Most Significant Byte)
and LSB (Least Significant Byte) of the parameter number, and subsequently-transmitted
Control Change messages of Control Change number 6 (or 6 and 38) to specify the value of
that parameter.
The event assigned to each combination of MSB and LSB is pre-defined, and cannot be
changed.
NOTE
For details on the events assigned to NRPN messages, refer to the data list at the end of this
manual.
NOTE
Assignments to control numbers are maintained as settings for the entire system, rather than for
individual scenes.
STEP
1. Connect the CL series console to an external device.
2. As described in “Basic MIDI settings” (page 192), select the ports and MIDI channels
that will be used to transmit/receive control changes.
3. Press the CONTROL CHANGE tab in the MIDI/GPI screen.
4. Switch Control Change transmission/reception on or off, select transmission/
reception mode, and set echo output.
5. To change the event assignment for each control number, press the desired event
in the list and select an event type and the recall target.
MIDI/GPI screen
(CONTROL CHANGE page)
MIDI
V5 Reference Manual
198
MIDI/GPI screen (CONTROL CHANGE page)
You can specify how Control Changes will be transmitted and received, and specify the event
(fader/knob operation, [ON] key on/off operation, etc.) assigned to each control number.
1 CONTROL CHANGE field
Enables you to switch Control Change transmission/reception on or off, and specify
whether Control Changes will be echoed out. This setting is linked with the CONTROL
CHANGE field on the MIDI SETUP page.
Tx button ............................... Switches control change transmission on/off.
Rx button............................... Switches control change reception on/off.
ECHO button......................... Selects whether incoming control changes will be
echoed out from the MIDI transmit port.
2 CONTROL CHANGE MODE field
This field enables you to select the Control Change transmission/reception mode. This
setting is linked with the CONTROL CHANGE MODE field on the MIDI SETUP page.
NRPN mode (when the NRPN button is on):
Various mix parameters on the CL series console will be transmitted and received on a
single MIDI channel as NRPN messages. If you select this mode, the assignments in the
list will be ignored.
TABLE mode (when the TABLE button is on):
Various mix parameters on the CL series console will be transmitted and received on a
single MIDI channel as Control Change messages, according to the assignments in the
list.
NOTE
The channel on which Control Changes are transmitted and received is specified by the PORT/
CH field on the MIDI SETUP page (page 193).
3 List
Shows the event (fader/knob operation, [ON] key on/off operation, etc.) assigned to
each control number.
NO..........................This indicates the control number. You can use control numbers 1-
31, 33-95, and 102-119.
CONTROL CHANGE EVENT
.........................Indicates and enables you to select the type of event assigned to
each control number. When you press an event, the MIDI
CONTROL CHANGE window will appear, allowing you to change
the control number assignment.
4 CLEAR ALL button
Press this button to clear all event assignments on the list.
5 INITIALIZE ALL button
Press this button to restore all event assignments on the list to their default state.
6 Scroll knob
Scrolls the contents of the list. You can use the multifunction knobs to operate this.
1
6
4
5
2
3
MIDI
V5 Reference Manual
199
MIDI CONTROL CHANGE window
Display this window by pressing any event in the CONTROL CHANGE page. In this window,
you can specify the event assigned to each control number.
1 MODE field
Enables you to select the type of event.
2 PARAMETER 1/2 field
In conjunction with the MODE field, this field specifies the type of event.
3 OK button
Confirms the settings and closes the window.
NOTE
The list shown is the same for all models of the CL series. For the CL3/CL1, the display will
indicate “Cannot Assign!” if you specify a parameter that does not exist on that model.
If NRPN mode is selected as the control change transmission/reception mode, the settings in this
window are ignored.
For details on the events that can be assigned to Control Changes, refer to the data list at the end
of this manual.
Using parameter changes to control parameters
On the CL series console, you can use a type of system exclusive messages called
“Parameter Changes” to control specific events (fader/knob operations, [ON] key on/off
operations, system and user settings, etc.) as an alternative to using Control Changes or
NRPN messages.
For details on the Parameter Changes that can be transmitted and received, refer to the data
list at the end of this manual.
NOTE
Parameter changes include a “device number” that specifies the transmitting or receiving device.
The transmit (Tx) channel and receive (Rx) channel specified on the MIDI SETUP page are used
as the device number.
Please be aware that if the device number included in the transmitted Parameter Change does
not match the device number of the receiving CL console, the message will be ignored.
Do not turn Parameter Change and Control Change transmission/reception on at the same time.
Otherwise, a large amount of data will flood the MIDI port and may cause overflows or other
problems.
1
2
3
STEP
1. Connect the CL series console to an external device.
2. As described in “Basic MIDI settings” (page 192), select the ports and MIDI channels
(device number) that will be used to transmit/receive parameter changes.
3. Use the Tx button and Rx button of the PARAMETER CHANGE field in the MIDI
SETUP page to turn on parameter change transmission/reception.
Recorder
V5 Reference Manual
200
Recorder
This chapter explains the functionality and operation of the recorder.
About the USB memory recorder
The CL series console features a USB memory recorder function that lets you easily record
internal audio signals to a USB flash drive, or play back audio files recorded on a USB flash
drive.
As the file format for recording, the CL series console supports MP3 (MPEG-1 Audio Layer-
3). For playback, it supports MP3 as well as WMA (Windows Media Audio) and AAC (MPEG-
4 AAC) files. However, DRM (Digital Rights Management) is not supported.
By using the USB memory recorder, the output from the STEREO bus or a MIX bus can be
recorded to a USB flash drive, or background music or sound effects saved on the USB flash
drive can be played back via an assigned input channel.
Signal flow for the USB memory recorder
* CL3: INPUT1-64, CL1: INPUT1-48
NOTE
Recording and playback cannot be done simultaneously.
The signal being recorded cannot be input to an INPUT channel.
Assigning channels to the input/output of the
recorder
Follow the steps below to patch the desired channels to the input and output of the USB
memory recorder. You can patch any desired output channel or the direct output of an INPUT
channel to the recorder input, and you can patch the recorder output to any desired input
channel.
NOTE
The USB memory recorder always records and plays back in stereo. If you want to record in
monaural, with the same signal for left and right, you must assign both of the recorder inputs to
the same channel.
You can patch multiple channels to the recorder output.
In steps 4 and 8, if you select a channel to which another port is already patched, a dialog box
will ask you to confirm the patch change. Press the OK button in the dialog box.
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
MIX1-24
MATRIX1-8
STEREO L/R
MONO
INPUT1-72*
DIRECT OUT
RECORDER
INPUT
PLAYBACK
OUT
INPUT1-72*
ST IN 1L1R-8L8R
L
R
L
R
USB
memory
recorder
STEP
1. In the Function Access Area, press the RECORDER button.
2. Press the USB tab in the RECORDER screen.
3. Press the RECORDER INPUT L or R button.
4. Use the category list and the port select buttons in the CH SELECT window to select
the channel that you want to patch to the USB memory recorder input.
5. When you have finished assigning the channel, press the CLOSE button.
6. Assign a channel to the other input in the same way.
7. Press the PLAYBACK OUTPUT L or R button.
8. Use the category list and the channel select buttons in the CH SELECT window to
select the channel that you want to patch to the USB memory recorder output.
9. When you have finished assigning the channel, press the CLOSE button.
10. Assign a channel to the other output in the same way.
RECORDER screen
Recorder
V5 Reference Manual
201
RECORDER screen (when selecting the USB tab)
In this screen you can assign signals to the input and output of the USB memory recorder,
and perform recording and playback operations.
1 RECORDER INPUT L/R buttons
Press these buttons to open the CH SELECT window, in which you can select the signals
patched to the recorder’s L/R input channels.
2 RECORDER INPUT GAIN knob
Sets the level of the signal input to the recorder.
3 RECORDER INPUT CUE button
When this button is turned on, you can monitor the signal input to the recorder.
NOTE
You cannot turn on this button and the PLAYBACK OUTPUT CUE button simultaneously.
The cue monitoring does not support CUE B.
4 Meters
Indicate the level of the signals input to the recorder.
5 PLAYBACK OUTPUT L/R buttons
Press these buttons to open the CH SELECT window, in which you can select the signals
patched to the recorder’s L/R output channels for playback.
6 PLAYBACK OUTPUT GAIN knob
Sets the level of the signal output to the recorder.
7 PLAYBACK OUTPUT CUE button
Press this button to monitor the signal output from the recorder.
NOTE
You cannot turn on this button and the RECORDER INPUT CUE button simultaneously.
The cue monitoring does not support CUE B.
8 Meters
Indicate the level of the signals output to the recorder.
CH SELECT window
Display this window by pressing the RECORDER INPUT L or R button or the PLAYBACK
OUTPUT L or R button.
1 Category List
Enables you to select the type of channel.
2 Channel select button
Select the channels that will be patched to the USB memory recorder’s inputs and
outputs. The channels that can be patched at input or output are different.
Channels that can be patched to the recorders inputs
MIX 1-24................................. MIX channels 1-24
MTRX 1-8 ............................... MATRIX channels 1-8
ST L/R.................................... STEREO channel L/R
ST L+C................................... STEREO channel L mixed with the MONO (C) channel
ST R+C .................................. STEREO channel R mixed with the MONO(C) channel
MONO.................................... MONO channel
CH1-72................................... Direct output of an INPUT channel 1-72
Channels that can be patched to the recorders outputs
CH1-72................................... INPUT channels 1-72
STIN 1L/1R-STIN 8L/8R ........ ST IN channels 1-8L/R
1 2 3 4 8765
2
1
2
1
Recorder
V5 Reference Manual
202
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
Recording audio to a USB flash drive
You can record the signal of the desired output channels as an audio file (MP3) onto the USB
flash drive inserted in the USB connector located to the right of the display.
NOTE
The FREE SIZE field indicates the amount of free capacity in the USB flash drive.
The signal being recorded will not be output from the recorder output jacks (PLAYBACK OUT).
The level meter on the RECORDER screen shows the signal level before and after the recorder.
If necessary, use the GAIN knob in the RECORDER INPUT field to adjust the input level to the
recorder. Operating the GAIN knob will not affect the level of the signal being output to other ports
from the corresponding output channel.
In the default state, the recorded audio file will be saved in the SONGS folder within the YPE
folder in the USB flash drive. However, you may also specify a folder of a level below the SONGS
folder.
The recorded file will be given a default title and file name. You can change this later.
RECORDER screen (when selecting the USB tab)
TRANSPORT field
This field enables you to control recording and playback of a song.
1 Current song
Indicates the currently-selected song’s track number, title and artist name. The following
indicators will appear during playback or recording.
2 Elapsed time display
Indicates the elapsed playback time of the current song during playback, and the
elapsed recording time during recording.
3 Remaining time display
Indicates the remaining playback time of the current song during playback, and the
available recording time during recording.
4 Current song format
Indicates the file format and bit rate of the current song (the file being played back).
STEP
1. Refer to “Assigning channels to the input/output of the recorder” (page 200) to
assign channels to the input/output of the recorder.
2. Connect a USB flash drive with sufficient free capacity to the USB connector.
3. To monitor the signal being recorded, raise the fader for the channel(s) that are
patched to the input of the recorder.
4. Press the REC RATE button in the lower right of the RECORDER screen, then select
the bit rate for the audio file that will be recorded.
5. Press the REC () button located at the bottom of the screen.
6. To start recording, press the PLAY/PAUSE ( ) button in the lower part of the
screen.
7. To stop recording, press the STOP () button.
8. To audition the recorded content, proceed as follows.
8-1. Press the PLAY/PAUSE ( ) button to play back the recording.
8-2. To stop playback, press the STOP () button.
1
2
3 4A0987 5 6
The unit is currently playing back.
The unit is currently recording.
Recorder
V5 Reference Manual
203
5 REC RATE button
Switches the recording rate.
You can choose 96 kbps, 128 kbps, or 192 kbps. Higher bit rates will improve the audio
quality, but will increase the size of the data.
NOTE
The word clock rate at which the CL series console is currently operating will automatically be
selected as the sampling rate for the audio file.
6 Display Switch Button
Switches between displaying and hiding the RECORDER INPUT/PLAYBACK OUTPUT
fields at the bottom of the song list.
7 REW button
Moves the playback point to the beginning of the current song and stops playback. If
the playback point is already at the beginning, the point will move to the beginning of
the preceding song that has been selected for playback.
If the playback point is not at the beginning of the current song, holding down this
button for two seconds or longer will rewind the playback point.
If you operate this button during playback, playback will resume from the point at which
the button was released.
8 STOP button
The recorder will change from play/record/recording-standby mode to stop mode.
9 PLAY button
Changes the recorder mode as follows.
Stop mode
Playback mode, then starts playback from the beginning of the current
song.
Playback modePlayback-pause mode
Playback pause mode
Playback mode, then starts playback from the paused point.
Recording standby mode
Recording mode
Recording mode
Recording-pause mode
Recording-pause mode
Recording mode, then starts recording from the paused point.
0 FF button
Moves the playback point to the beginning of the next song that is marked with a PLAY
check symbol.
The pause indicator of the PLAY/PAUSE() button will light.
A REC button
Places the recorder in recording standby mode.
NOTE
You can also assign the function of each button to a USER DEFINED key (page 224).
Directory structure of a USB flash drive
When you connect a USB flash drive to the USB connector, a YPE folder and a SONGS folder
within that YPE folder will be created automatically in the root directory of the USB flash drive.
The files created by recording operations will be saved in the above SONGS folder, or in the
currently-selected folder below that level.
Song
(audio file)
Songs folder
YPE folder
Root directory
Recorder
V5 Reference Manual
204
Playing back audio files from a USB flash drive
You can play back audio files that have been saved on your USB flash drive. In addition to files
that were recorded on the CL series console, you can also play files that were copied from
your computer to the USB flash drive.
The three types of file format that can be played are MP3 (MPEG-1 Audio Layer-3), WMA
(Windows Media Audio), and AAC (MPEG-4 AAC). The playable sampling rates are 44.1 kHz
and 48 kHz. The supported bit rate ranges from 64 kbps to 320 kbps.
NOTE
If you want to play back an audio file, you must save it in the SONGS folder within the YPE folder,
or in a folder you have created below the SONGS folder. Files located in other folders and files of
unsupported formats will not be recognized.
The CL series console can recognize a file name that is a maximum of 64 single-byte characters.
If the file name is longer than this, the desired file may not play correctly.
A maximum of 300 songs can be managed in a single directory. A maximum of 64 subdirectories
can be managed.
NOTE
Even if the sampling rate at which the CL series console is operating differs from the sampling
rate of the audio file being played, the SRC (Sampling Rate Converter) function will automatically
convert the rate so that the file will be played back correctly.
If the REPEAT button is on, playback will continue until you stop playback.
RECORDER screen
Title list
This list enables you to perform operations related to the songs and directories that are saved
on the USB flash drive.
1 Selected song
The currently selected song will appear in a blue frame.
2 Status indicator
Displays a symbol to indicate whether the currently-selected file is playing or paused.
: Playing, : Paused
3 Track number
Indicates the file number in the title list.
STEP
1. Connect a USB flash drive that contains the audio files to the USB connector.
2. In the Function Access Area, press the RECORDER button.
3. You can use the change directory icon in the RECORDER screen and the folder icon
in the No. field to view a content list of the folder that includes the desired file.
4. Use the multifunction knob or press the on-screen file name to select the desired file.
5. Press a button in the PLAY MODE field to select the playback mode.
6. If you turned on the REPEAT button in step 5, press the PLAY checkmark for the song
you want to play.
7. Press the PLAY/PAUSE ( ) button to play back the song.
8. To stop playback, press the STOP () button.
6 7 8 9
3 5 4 1
2
A
0
C
B
Recorder
V5 Reference Manual
205
4 Sub-directory
Indicates each song’s track number, the name of upper level directory, and whether a
sub-directory exists (in the case that the directory has been selected).
Upper level............Press this to move up to the directory that is one level higher than
the current one.
Sub-directory................Press this to move to that sub-directory.
NOTE
If you switch folders, that folder will be selected as the recording destination.
The folders that can be selected are restricted to the SONGS folder inside the YPE folder, and
folders located below the SONGS folder.
5 PLAY check symbol
Enables you to select multiple files that will be played back consecutively.
6 SELECT knob
Use the multifunction knob to select a song.
7 NOW PLAYING button
Press this button to always select the currently-playing song on the list.
8 MOVE UP/MOVE DOWN buttons
Change the order of the selected song in the list.
9 Display switch buttons
Switch the list between the SONG TITLE display and the FILE NAME display.
0 SAVE LIST button
Saves the order of the current title list and PLAY check symbol settings as a playlist.
A RELOAD button
Loads the playlist that was saved most recently. Use this button to revert the current
playlist you are editing back to the previous state.
PLAY MODE field
Sets the playback method of the currently selected song.
B SINGLE button
If this button is on, the recorder will stop after playback of the current song is complete.
If this button is off, the recorder will play the next song on the list after playback of the
current song is complete.
C REPEAT button
If this button is on, after playback of the current song is complete, the recorder will play
the first song on the list that is marked with a PLAY check symbol (unless there are no
subsequent songs that are marked with a PLAY check symbol).
If this button is off, the recorder will stop after playback of the current song is complete
(unless there are no subsequent songs that are marked with a PLAY check symbol). One
of the following playback methods is selected according to the on/off settings of the
SINGLE button and the REPEAT button.
Editing the title list
You can change the order of the audio files shown in the title list, and edit the titles or artist
names.
NOTE
If the title or artist name contains characters that cannot be displayed, these characters will be
converted into for display.
The title and the artist name can be edited only for MP3 format audio files.
SINGLE
button
REPEAT
button
Mode
On On
The currently-selected song will play repeatedly until you stop
playback.
On Off The currently-selected song will play once and then stop.
Off On
Songs with the PLAY checkmark selected are played in order,
starting with the currently-selected song, and then they are
played again from the first song in the title list. The currently-
selected song will play repeatedly until you stop playback.
Off Off
Songs with the PLAY checkmark selected are played in order,
starting with the currently-selected song. After the final song in
the title list is played, playback stops.
STEP
1. Connect a USB flash drive containing audio files to the USB connector.
2. In the Function Access Area, press the RECORDER button.
3. Press the No. button and the change directory icon in the RECORDER screen to view
a list of the contents of the folder that includes the desired file.
4. If you want to edit a title in the title list, press the SONG TITLE/FILE NAME EDIT
button. If you want to edit the artist name, press the ARTIST EDIT button.
5. Edit the title or artist name, and press the OK button.
6. If necessary, use the SONG TITLE/FILE NAME SORT button, ARTIST SORT button,
and MOVE UP/MOVE DOWN buttons on screen to change the order of the title list.
7. When editing is complete, press the SAVE LIST button to save the changes.
Recorder
V5 Reference Manual
206
RECORDER screen (when selecting the USB tab)
1 SONG TITLE/FILE NAME EDIT button
Enables you to edit the title of the song selected in the list.
2 ARTIST EDIT button
Enables you to edit the artist name of the song selected in the list.
NOTE
A maximum of 128 single-byte characters (64 double-byte characters) can be input for both the
title and for the artist name. If the title cannot be shown completely, scroll horizontally.
3 SONG TITLE/FILE NAME SORT button
Sorts the list in alphabetical order of the title.
4 ARTIST SORT button
Sorts the list in alphabetical order of the artist name.
5 SAVE LIST button
Saves the order of the list and PLAY check symbol settings as a playlist on the USB flash
drive.
6 SONG TITLE/FILE NAME button
Enables you to select either song title or file name to be displayed in the SONG TITLE/
FILE NAME field.
Recording or playing back using a computer DAW
If you plan to add DAW software, such as Steinberg Nuendo, to an audio network that includes
a CL console and I/O devices, you must use Dante Virtual Soundcard (DVS) driver software.
DVS works as an audio interface, making it possible to transmit signals between a DAW and
an audio network (that includes a CL series console and I/O devices). In this way, you will be
able to make multi-track recordings of live performances or use live recordings that were
made a day earlier for a virtual sound check.
This section explains the steps required when adding DAW software to an audio network.
Required devices and software
CL series console and I/O devices
A computer (Windows or Mac) equipped with an Ethernet port that supports a Giga-bit
Ethernet (GbE) network; DAW software
A GbE-compatible network switch
•CAT5e cable
Dante Virtual Soundcard driver software
Dante Controller control software
NOTE
You must have a license ID to use Dante Virtual Soundcard. A sheet with the DVS token needed
to acquire the license ID is included in the CL unit package.
The latest information about the Dante Virtual Soundcard and the Dante Controller is available at
the following website:
https://www.yamaha.com/proaudio/
3 4
2
5
6
1
Recorder
V5 Reference Manual
207
Word clock settings
In a Dante network, the master device supplies accurate word clock to other devices on the
network. If the master device is removed from the network or breaks down, another device
will automatically take over as the clock master.
To make this setting, in the Function Access Area, press the SETUP button, then the WORD
CLOCK/SLOT SETUP button to access the WORD CLOCK/SLOT SETUP window.
Setting up Dante Virtual Soundcard
Install Dante Virtual Soundcard (DVS) and
Dante Controller in the computer that you
want to use for audio recording.
Make the following settings before turning
DVS on.
Connect the GbE-compatible network port
of the computer to a GbE-compatible
network switch.
Configure the computer to obtain an IP
address automatically
(this is the default setting).
Set the audio format.
(Example: 48kHz, 24 bit)
Set the Dante latency. (Use a high setting to
ensure stability when using multiple
channels.)
In the Advanced settings, select the number
of channels to be used for recording and
playback (the default is 8 x 8).
NOTE
Please refer to the Dante Virtual Soundcard Users Guide for more information on ASIO settings
(Windows).
Dante Accelerator settings
After mounting a Dante Accelerator card on the computer, install the Dante Accelerator Driver
and make the following settings. For information about how to install the driver, refer to the
Installation Guide included with the driver.
Use a network cable to connect the Dante jack on the Dante Accelerator card to the Dante
network, and then connect the computer’s network port to the same network.
Configure the computer to obtain an IP address automatically (this is the default setting).
NOTE
For more information about selecting a computer for remote control from a CL series console,
refer to “Specifying DVS or Dante Accelerator” in “When setup method selection button =
SPECIFIED IP ADDRESS” (page 211).
V3.7 and earlier
V3.7
Recorder
V5 Reference Manual
208
Setting up Dante Controller
Connect the network port of the computer to a GbE-compatible network switch. Configure the
computer to obtain an IP address automatically (this is the default setting).
You must make the following settings for Dante Controller.
For multi-track recording, patch audio signals from the I/O device to DVS or the Dante
Accelerator card.
For virtual sound check: Patch audio signals in such a way that they will be output from the
computer to the Dante audio network, then routed to the channels on the CL console
(page 174).
The following example shows Dante Controller settings for when channels 1-16 of an I/O
device are patched to DVS.
In this case, youll need to switch the DANTE INPUT PATCH settings of the CL series console
depending on whether you’re performing multitrack recording or multitrack playback. If you’ve
saved these different sets of settings in the DANTE INPUT PATCH LIBRARY (page 174), you’ll
be able to switch between them conveniently.
NOTE
Please refer to the Dante Controller manual for more information about operations and settings
of the Dante Controller.
Setting up DAW software
You must make driver settings in your DAW software. You must make driver settings in your
DAW software. In the device setting window, select “Dante Virtual Sound Card-ASIO” (“Dante
for Mac) or “Yamaha AIC128-D” as the sound card (or audio driver) used for input/output.
Some DAW software may require internal patching for the driver and the DAW software. For
more information, refer to the DAW software manual.
Setting up Nuendo Live
If you install the “Yamaha Console Extension” software for linking Nuendo Live to a console,
and then start up Nuendo Live and create a new project, tracks corresponding to the number
of channels specified in DVS will be created automatically, and the channel names and colors
from the CL series console will automatically be assigned as each track name.
Audio recording and playback
After you have made driver settings in your DAW software, you can record and play back
audio.
For multi-track recording, set the input ports for the tracks of the DAW software to the ports
that receive audio signals from the I/O devices.
For a virtual sound check, you must route recorded audio signals to the input channels on the
CL console. To do so, use Dante Controller to patch the signals so that the signals will be
output from the DAW software to DANTE 1-64 on the CL console. It may be convenient for you
later if you store two sets of the DANTE INPUT PATCH settings in the library: one set for
routing audio signals from the I/O devices, and another set for routing audio signals from DAW
software. In this way, you will be able to switch between patch settings without starting Dante
Controller. In addition, you will be able to patch a specific channel (such as a vocal) to the I/
O device to monitor during a virtual sound check.
Recorder
V5 Reference Manual
209
Using the CL console with Nuendo Live
The CL series consoles can operate in an integrated manner with Steinberg’s Nuendo Live
DAW software.
The “Yamaha Console Extension” software which integrates the CL series and Nuendo Live
can be installed in your computer, allowing you to operate Nuendo Live from the CL series
console to easily perform multi-track recording operations.
Here we explain how to operate Nuendo Live from the CL series console.
Preparing the project
Refer to “Recording or playing back using a computer DAW” (page 206) to make the following
settings.
Setting up Dante Virtual Soundcard
Setting up Dante Controller
Setting up Nuendo Live
Recording into a project
RECORDER screen (when selecting the Nuendo Live tab)
1 Nuendo meter display field
This shows the channel levels of Nuendo Live.
2 PEAK CLEAR button
Clears the peak levels indicated by the peak hold function.
3 Marker list field
Lists the marker information recorded in the current Nuendo Live project.
The markers can be selected by pressing the on-screen list or by using the multifunction
knobs.
When you press this field, a keyboard window allowing you to edit the marker
information will appear.
4 Nuendo Live SETUP button
Specify the device that the console will use for communication when working with
Nuendo Live (page 210).
5 DANTE INPUT PATCH button
Press this to access the DANTE INPUT PATCH window (page 174).
6 Location information display
This displays information for the current location of the Nuendo Live project. You can
press the button at the right to switch the time display format.
STEP
1. In the Function Access Area, press the RECORDER button.
2. Press the Nuendo Live tab in the upper right of the RECORDER screen.
3. Press the EASY RECORDING button to start recording.
4. When you finish recording, press the record lock button and then press the STOP
button.
RECORDER screen
(when selecting the Nuendo Live tab)
1
6
3
2
4
5
HEDCBA0987
I
F
G
Recorder
V5 Reference Manual
210
Transport field
Here you can operate the transport of Nuendo Live.
7 GO TO PROJECT START button
Returns the location to the start of the project.
8 GO TO PREVIOUS MARKER button
Returns the location to the previous marker.
9 GO TO NEXT MARKER button
Advances the location to the next marker.
0 GO TO PROJECT END button
Advances the location to the end of the project.
A CYCLE button
Turns repeat on/off for the project.
B STOP button
Stops playback/recording of the project.
C PLAY button
Starts playback of the project.
D RECORD button
Starts/stops recording of the project.
E EASY RECORDING button
Immediately starts recording on all tracks.
When you press this, the location will move to the last-recorded position, all tracks will
be set to record mode, recording will begin, the record panel will be displayed, and the
panel will be locked. The recording will be started retrospectively.
(Default setting: 10 seconds)
F ADD MARKER button
Adds a marker to the project at the current location.
G RECALL LINK button
Specifies whether a marker will be created when you recall a scene. If this function is
turned on, the button will be lit.
H Record lock button
Turns recording status lock on/off. This prevents recording from being accidentally
stopped during recording.
NOTE
Transport functions can also be controlled from USER DEFINED keys (page 224).
I DVS information display
Shows the device label of the selected DVS.
Specifying DVS or Dante Accelerator
Before you proceed, use DANTE SETUP to specify the I/O devices that will be mounted. For
details, refer to “Mounting an I/O device on the Dante audio network” (page 263).
NOTE
You can specify either DVS or Dante Accelerator in the NUENDO LIVE SETUP window.
However, do not select the same DVS or Dante Accelerator from multiple CL series consoles.
NUENDO LIVE SETUP window
In this window, specify the device that the console will use for communication when working
with Nuendo Live.
STEP
1. In the Nuendo Live screen, press the NUENDO Live SETUP button.
2. In the NUENDO LIVE SETUP screen, press the setting method select button.
3. Use the corresponding multifunction knob to make settings.
4. When you have finished making settings, press the OK button to close the window.
1
Recorder
V5 Reference Manual
211
1 Setup method select buttons
Choose one of the following methods by which to specify DVS or Dante Accelerator.
NO ASSIGN ........................ Not assigned
DVS ..................................... Select a DVS from the device list
SPECIFIED IP ADDRESS .. When using Dante Accelerator, specify the IP address of
the computer
When setup method selection button = DVS
To choose from a list of the I/O devices on the Dante audio network, press the DVS button to
display the DEVICE LIST field.
1 DEVICE LIST
Shows a list of the I/O devices on the Dante audio network.
From the list, choose the DVS that you want to use with Nuendo Live.
2 DEVICE LIST select knob
Operate the multifunction knob to choose the DVS that you want to select.
When setup method selection button = SPECIFIED IP ADDRESS
When using Dante Accelerator, specify the IP address of the computer in the SPECIFIED IP
ADDRESS field. Since the IP address of Dante Accelerator will differ from the IP address used
by Yamaha Console Extension, you must specify the IP address manually.
1 IP ADDRESS knobs
Use the multifunction knobs to specify the IP address.
NOTE
As the IP address, specify the IP address of the computer that is running Nuendo Live.
Set the address of that computer in the range of 169.254.0.0 - 169.254.255.255, and set the
subnet mask as 255.255.0.0.
For the computer in which Dante Accelerator is installed, the Dante port of Dante Accelerator as
well as the Ethernet port of the computer must both be connected to the same network.
Refer to the illustration below.
1
2
1
Computer
SW
(Primary)
SW
(Secondary)
Ethernet
Dante Accelerator
P
S
CL
Dante
P
S
Recorder
V5 Reference Manual
212
NOTE
Depending on the firmware version, Dante Accelerator might not support redundant networking.
Refer to the following website to check whether your version of the Dante Accelerator firmware
supports redundant networking.
https://www.yamaha.com/proaudio/
Playing a multi-track project
NOTE
If you save the DANTE INPUT PATCH settings in a library, the settings of the CL series console
can be switched conveniently (page 174).
STEP
1. Press the DANTE INPUT PATCH button in the RECORDER screen (Nuendo Live page).
2. In the DANTE INPUT PATCH window, press the PORT SELECT button for the port to
which you want to assign the signal from Nuendo Live.
3. In the list at the left of the PORT SELECT window, select the DVS you’re using with
Nuendo Live, and select the port you want to assign it to.
4. Press the + button located in the upper part of the window to switch the port, and
assign a DVS port to it in the same way.
5. When you have finished making settings, press the CLOSE button to exit the
window.
6. Press the “X” symbol in the upper right of the DANTE INPUT PATCH window to close
it.
7. In the Nuendo Live screen, press the START button.
8. Operate the channels so that sound is output.
9. To stop playback, press the STOP button.
RECORDER screen
(when selecting the Nuendo Live tab)
DANTE INPUT PATCH window
PORT SELECT window
Setup
V5 Reference Manual
213
Setup
About the SETUP screen
The SETUP screen enables you to set various parameters that apply to the entire CL console.
To access the SETUP screen, press the SETUP button in the Function Access Area. The
screen contains the following items.
CURRENT USER field
This field enables you to make various user-related settings.
1 USER SETUP button
Press this button to open the USER SETUP window, in which you can make various
settings for each user.
2 CURRENT USER button
Press this button to open the LOG IN window, in which you can switch log-in users.
3 COMMENT EDIT button
Press this button to open the COMMENT EDIT window, in which you can enter
comments that will be displayed in the comment area.
4 PASSWORD CHANGE button
Press this button to open the PASSWORD CHANGE window, in which you can change
the password.
5 SAVE KEY button
Press this button to open the SAVE KEY window, in which you can overwrite (save) the
user authentication key (page 220).
STORAGE field
This field enables you to create, save, or load a user authentication key.
6 CREATE USER KEY button
Press this button to open the CREATE USER KEY window, in which you can create a new
user authentication key.
7 SAVE/LOAD button
Press this button to open the SAVE/LOAD window, in which you can save or load user
authentication keys and console files.
SYSTEM SETUP field
This field enables you to make various settings that globally apply to the CL series console.
8 +48V MASTER button
Switches the console’s master +48V master phantom power on or off. When this button
is off, +48V phantom power for all the head amps turns off.
NOTE
If this button is off, phantom power will not be supplied even if the +48V button of each channel
is on.
9 WORD CLOCK/SLOT SETUP button
Press this button to open the WORD CLOCK/SLOT SETUP window, in which you can
make word clock settings and various settings for each slot.
0 CASCADE button
Press this button to open the CASCADE window, in which you can make patch settings
for cascade connections.
A OUTPUT PORT button
Press this button to open the OUTPUT PORT window, in which you can make output
port settings.
B MIDI/GPI button
Press this button to open the MIDI/GPI window, in which you can make MIDI and GPI-
related settings.
C DANTE SETUP button
Press this button to open the DANTE SETUP window. This window enables you to make
various audio network settings (console ID setting; SECONDARY PORT functionality
setting; audio bit rate; latency setting; DANTE device ID and device type settings for
devices controlled via the I/O RACK screen).
1 6 72543
8
F
G
9
C
A
0
H
D
B
I J K
E
Setup
V5 Reference Manual
214
BUS SETUP field
This field enables you to make bus-related settings.
D BUS SETUP button
Press this button to open the BUS SETUP window, in which you can make MIX bus/
MATRIX bus-related settings.
E SURROUND SETUP button
Press this button to call up the SURROUND SETUP screen. In this screen, you can switch
the bus settings from Stereo mode to Surround mode. If set to Stereo mode, the bus
settings for MIX1-6 will be grayed out. If you press the 5.1 SURROUND button to switch
to Surround mode, you can then set the bus settings for MIX1-6.
Assign channels to MIX 1 - 6 for surround output. You can press the APPLY button to
open the CONFIRMATION dialog box. Press the OK button to set the bus to Surround
mode.
NOTE
When you switch from Stereo mode to Surround mode, the signals for MIX1/2, 3/4, and 5/6
change to MONO x2.
When you switch from Surround mode to Stereo mode, the signals for MIX1/2, 3/4, and 5/6
remain as MONO x2.
When you switch from Stereo mode to Surround mode, the STEREO and MONO(C) inserts are
turned off.
For Stereo mode
For Surround mode
Setup
V5 Reference Manual
215
If you set Surround mode, the BUS SETUP screen appears as shown below.
DATE/TIME button
Press this button to open the DATE/TIME window, in which you can set the date and time.
NETWORK button
Press this button to open the NETWORK window, in which you can set the network address.
Indicator field
This field displays various information about the console.
F BATTERY indicator
Indicates the status of the internal battery.
NOTE
The LOW or NO indication will appear if the battery runs down. In this case, immediately contact
your Yamaha dealer or a Yamaha service center listed at the end of the operating manual
(separate document) to have the backup battery replaced.
G POWER SUPPLY indicator
Indicates the currently-running power supply.
INT .........................Internal
EXT ........................PW800
H Version indicator
Indicates the version number of the main CPU, sub CPU, and Dante module.
CONSOLE LOCK button
This button executes the Console Lock function. If the console password has been set,
pressing this button will open the AUTHORIZATION window. Enter the correct password to
execute Console Lock.
If the console password has not been set, pressing this button will execute Console Lock
immediately.
CONTRAST/BRIGHTNESS field
This field enables you to set the LCD brightness and contrast.
I BANK A/BANK B buttons
Select a bank to which you want to save the brightness and contrast settings. You can
save two different settings in bank A and B, and switch between them if desired.
J CONTRAST NAME knob
Adjusts the contrast of the channel name display.
K BRIGHTNESS NAME knob
Adjusts the brightness of the channel name display.
BRIGHTNESS CH COLOR knob
Adjusts the brightness balance of the channel color and the channel name display.
BRIGHTNESS SCREEN knob
Adjusts the brightness of the display.
BRIGHTNESS PANEL knob
Adjusts the brightness of the panel LEDs.
BRIGHTNESS LAMP knob
Adjusts the brightness of the lamp connected to the LAMP connector.
User settings
User Level settings allow you to restrict the parameters that can be operated by each user, or
to change the settings of USER DEFINED keys and preference settings for each user.
Settings for each user can be stored as a “user authentication key” inside the console or
together on a USB flash drive, allowing users to be switched easily. This can be convenient in
the following situations.
Unintended or mistaken operation can be prevented.
The range of functionality operable by an outside engineer (guest engineer) can be
limited.
In situations in which multiple operators alternate with each other, output settings etc.
can be locked to prevent unintended operations.
Preferences of each operator can easily be switched.
Setup
V5 Reference Manual
216
User types and user authentication keys
There are three types of user, as follows. To operate the CL series console, you must log-in
as a user.
Administrator.... The administrator of the CL console can use all of its functionality.
Only one set of Administrator settings is internally maintained in the
console. The Administrator can create user authentication keys for
other users.
Guest
...... A Guest can use only the range of functionality permitted by the Administrator.
Only one set of Guest settings is maintained inside the console.
User ........A User can use only the range of functionality permitted by the
Administrator. User settings are saved internally or on a USB flash drive as
user authentication keys. Multiple sets of user settings (up to ten in internal
memory) can be saved, each with the desired user name.
A User who has Power User privileges can create or edit user
authentication keys with a specified user level.
When a user logs in, the user settings for that user are applied. User settings include the
following information.
Password (except for Guest)
User Level settings (except for Administrator)
•Preferences
USER DEFINED keys
USER DEFINED knobs
Assignable encoders
Custom fader bank
MASTER fader
Privileges for each user are as follows.
Setting the Administrator password
With the factory settings, the Administrator password is not set, meaning that anyone can log
in with Administrator privileges and perform all operations. If you want to restrict the
operations of other users, you must specify an Administrator password.
NOTE
The password can be up to eight characters. If the two passwords that were entered match, the
Administrator password will be set.
For details on entering a password, refer to “Entering names” in the separate Owner’s Manual.
Creating a user authentication key
You can create a user authentication key and save it on a USB flash drive or in the consoles
internal memory. A user authentication key can be created only by an Administrator or Power
User. The user level can be specified when the authentication key is created, but the USER
DEFINED key settings and preference settings will be carried over from the user who is
currently logged-in.
NOTE
You can store ten keys in the consoles internal memory.
The file name of the user authentication key will be specified as the current user name, and its
location will be specified as the root directory.
Logged-in user
Editing user setup
data, such as
USER DEFINED
keys and
Preferences
Editing User
Level settings
Password
setting
Editing
comments
User authentication key
Create
new
Overwrite-save
Administrator
Available
(Can edit the
settings for
Administrator
and for Guest.)
Available
(Cannot edit the
user level, since
the administrator
can always
perform all
operations. Can
edit the settings
for Guest.)
Available - Available -
User
Power user Available Available Available Available Available Available
Normal user
(User without
Power User
privileges)
Available
N/A
(Viewing only)
Available Available -
Available
(Excluding User
Level settings)
Guest Available
N/A
(Viewing only)
- Available - -
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the PASSWORD CHANGE button.
3. In the keyboard window, enter the password in the NEW PASSWORD field, then
enter the same password in the RE-ENTER PASSWORD field for verification, and
finally press the OK button.
SETUP screen Keyboard window
Setup
V5 Reference Manual
217
CREATE USER KEY window
1 USER NAME
Displays the user name. Press this area to access a keyboard window, in which you can
enter a user name of up to eight characters.
2 COMMENT
Displays a comment about the user. Press this area to access a keyboard window, in
which you can enter a comment of up to 32 characters.
3 PASSWORD
Enables you to specify a password. Press this area to access a keyboard window, in which
you can enter a password of up to eight characters.
4 POWER USER
Specifies whether Power User privileges will be granted to this user.
5 ACCESS PERMISSION
These settings specify the range of operations that the user can perform. For details on
each item, refer to page 220.
NOTE
In the case of the CL3/CL1, faders that do not exist on those models will not be shown.
STEP
1. To create a user authentication key on a USB flash drive, connect a USB flash drive
to the USB connector.
2. In the Function Access Area, press the SETUP button.
3. In the SETUP screen, press the CREATE USER KEY button.
4. In the CREATE USER KEY window, when you have specified the user name, comment,
password, power user privileges on/off, and user rights, press the CREATE button.
5. If you want to create a user authentication key in the console’s internal memory,
press a button in the CREATE TO INTERNAL STORAGE field in the CREATE KEY
window. If you want to create a user authentication key on your USB flash drive,
press the PATCH button in the CREATE TO USB STORAGE field.
6. Press the CREATE TO button.
7. Press the OK button in the confirmation dialog box.
SETUP screen CREATE USER KEY window
CREATE KEY window
1
2 3 4
5
Setup
V5 Reference Manual
218
Logging-in
To operate the CL series console, you must log in as the Administrator, Guest, or a User.
User settings for the Administrator and Guest are saved in the console itself. However, to log
in as a User you must either select a key that is saved in the console itself, or connect the
USB flash drive in which a user authentication key has been saved. If you use a user
authentication key on a USB flash drive, you will continue as the logged-in user even if you
remove the USB flash drive after logging-in. If you use a user authentication key on a USB
flash drive, you will continue as the logged-in user even if you remove the USB flash drive after
logging-in.
NOTE
If the power is turned off and then on again, the console will generally start up in the log-in state
in which the power was turned off. If a user password has been assigned, you will need to enter
the password. However if you cancel the input, you will be forcibly logged-in as Guest.
Logging-in as Administrator
NOTE
If no Administrator password has been set, you will simply be logged-in in step 3 when you press
the LOGIN button. If a password has been set, a keyboard window will appear, allowing you to
enter the password.
If the password was incorrect, a message of “WRONG PASSWORD” will appear near the bottom
of the screen.
Logging-in as Guest
Logging-in as a User
To log-in as a User, you will use a user authentication key saved in the console or on a USB
flash drive. If using a USB flash drive, you may also log-in using a user authentication key
created on a different CL series console.
With a user authentication key stored in the console
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the CURRENT USER button.
3. In the LOGIN window, press the ADMINISTRATOR button.
4. Enter the password and press the OK button.
SETUP screen LOGIN window
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the CURRENT USER button.
3. In the LOGIN window, press the GUEST button, and then press the LOGIN button.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the CURRENT USER button.
3. In the LOAD FROM INTERNAL STORAGE field of the LOGIN window, choose the user
authentication key with which you want to log in, and press the LOGIN button.
4. Enter the password and press the OK button.
SETUP screen LOGIN window
Setup
V5 Reference Manual
219
NOTE
If no password has been set, you will simply be logged-in in step 3 when you press the LOGIN
button.
If the password was incorrect, a message of “WRONG PASSWORD” will appear near the bottom
of the screen.
With a user authentication key stored in a USB flash drive
NOTE
If no password has been set, you will simply be logged-in in step 6 when you press the LOAD
button.
If the password was incorrect, a message of “WRONG PASSWORD” will appear near the bottom
of the screen.
If you have selected a user authentication key that was created on a different CL series console,
a keyboard window will appear, allowing you to enter the Administrator password of the CL series
console that you will be using. (If the Administrator passwords are identical, this window will not
appear.) When you enter the correct Administrator password, another keyboard window will
appear, allowing you to enter the password for the selected user. If you re-save the user
authentication key, you will not be asked for the Administrator password the next time. Refer to
Editing a user authentication key” (page 220).
For details about loading files from the USB flash drive, refer to “Loading a file from a USB flash
drive” (page 242).
Changing the password
Follow the steps below to change the password of the logged-in user. The Guest account
does not have a password.
NOTE
After you change the password, if you log out from the console without saving the user
authentication key, the changed password will be discarded.
STEP
1. Connect the USB flash drive to the USB connector.
2. In the Function Access Area, press the SETUP button.
3. In the SETUP screen, press the CURRENT USER button.
4. In the LOAD FROM USB STORAGE field of the LOGIN window, press the (LOAD .CLU
FILE) button.
5. In the SAVE/LOAD window, choose the user authentication key with which you want
to log in.
6. Press the LOAD button.
7. Enter the password and press the OK button.
SETUP screen LOGIN window
LOGIN window SAVE/LOAD window
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the PASSWORD CHANGE button.
3. In the keyboard window, enter the current password and press the OK button.
4. Enter the new password in the NEW PASSWORD field, then enter the same
password in the RE-ENTER PASSWORD field for verification, and finally press the OK
button.
5. Refer to “Editing a user authentication key” (page 220) to overwrite the user
authentication key.
Setup
V5 Reference Manual
220
Editing a user authentication key
If you are logged-in as a user, you can edit your USER DEFINED keys, preference settings,
comments and password, and save them onto your user authentication key. If you are logged-
in as a Power User, you can also change the user level.
NOTE
If you are logged-in as a Power User, you can also change the user level.
If you loaded a user authentication key from a USB flash drive, press the SAVE KEY button before
removing the USB flash drive. If you do remove the USB flash drive before pressing this button,
load the user authentication key again.
Changing the user level
You can view or change the user level.
Administrator................The Administrator does not have a user level setting, but can
change the user level setting of the Guest account.
Guest.............................The Guest can view the user level setting of the Guest
account. It cannot be changed.
Normal user ..................A normal user can view the user level setting of his or her
User account. It cannot be changed.
Power User ...................A power user can view and change his or her User account.
STEP
1. Log-in as a user, and edit the USER DEFINED keys (page 224) and Preference settings
(page 222).
2. Close the USER SETUP window.
3. In the SETUP screen, press the SAVE KEY button.
4. In the SAVE KEY window, choose the save-destination button, and then press the
SAVE TO button.
5. If you selected the same location as the current user authentication key, press the
OK button in the dialog box that asks you to confirm that you want to overwrite that
user authentication key.
SETUP screen SAVE KEY window
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the USER LEVEL tab. (If you are logged-in as the
Administrator, press the FOR GUEST button to switch to the USER LEVEL for Guest
page.)
4. Specify the user level by pressing the button for each item that will be permitted.
5. When you have finished making settings, close the window and press the SETUP
button in the Function Access Area.
SETUP screen USER SETUP window
Setup
V5 Reference Manual
221
USER SETUP window (USER LEVEL page)
1 CH OPERATION
Here you can specify (for each channel) the operations that will be permitted for input
channels, output channels, and DCA groups. The settings will apply to the currently-
selected channel. Settings for currently-selected channels will be displayed below the
CH OPERATION section. Use the panel [SEL] keys or the Selected Channel field in the
Function Access Area to select the channel for which you want to make settings.
The type of buttons shown will depend on the selected channel or group.
INPUT channel................... [HA], [PROCESSING], [FADER/ON]
MIX/MATRIX channel......... [WITH SEND], [PROCESSING], [FADER/ON]
STEREO/MONO channel
......................... ............ [PROCESSING], [FADER/ON]
DCA group ......................... [DCA MASTER], [DCA GROUP ASSIGN]
HA ....................................... Restricts operation of the HA (Head Amp) patched to that
channel.
PROCESSING .................... Restricts operation of all signal processing parameters
for that channel (excluding the fader, [ON] key, and send
level).
FADER/ON.......................... Restricts operation of that channel’s fader, [ON] key, and
send level.
WITH SEND........................ Restricts operation of that channel’s send parameters.
(From MIX, From MATRIX)
DCA MASTER .................... Restricts operation of that channel’s DCA group fader,
ON/OFF, and ICON/COLOR/NAME.
DCA GROUP ASSIGN........ Restricts changes of assignment to that DCA group.
SET BY SEL ....................... If this button is on, you can press the panel [SEL] key of
a channel to enable or disable the above-mentioned
operating restrictions for that channel.
2 CURRENT SCENE
Specifies the operations that can be performed on the current scene memory.
INPUT PATCH/INPUT NAME
..................... Restricts operations for input channel patching and
names.
OUTPUT PATCH/OUTPUT NAME
..................... Restricts operations for output channel patching and
names.
BUS SETUP ....................... Restricts operations for bus setup.
GEQ RACK/EFFECT RACK/PREMIUM RACK
..................... Restricts operations for the racks. Press this area to open
the RACK USER LEVEL window, in which you can set
this restriction.
However, there will be no restriction on operating the
MIDI CLK button displayed for delay-type and
modulation-type effects, or the PLAY/REC button
displayed for the FREEZE effect.
MUTE GROUP ASSIGN/MASTER
..................... Operations for mute group assignment and mute group
master will be restricted.
NOTE
In the case of the CL3/CL1, faders that do not exist on those models will not be shown.
3 SCENE LIST
Specifies the operations that can be performed on scene memories.
STORE/SORT operations
RECALL operations
4 LIBRARY LIST
Specifies the operations that can be performed on libraries.
STORE/CLEAR operations
RECALL operations
3
4
1
8
2
6
7
5
Setup
V5 Reference Manual
222
5 FILE LOAD
Specifies the types of file that can be loaded from USB flash drives. The user
authentication key contains the user level, USER DEFINED keys, and Preference settings.
Other data is saved in anALL” file. The ALL” file also includes the USER SETUP settings
of the Administrator and the Guest.
USER SETUP (USER DEFINED keys and Preferences settings)
SYSTEM SETUP/MONITOR SETUP
CURRENT SCENE
SCENE LIST
LIBRARY LIST
6 MONITOR SETUP
Specifies the monitor setup operations that can be performed.
•OSCILLATOR
TALKBACK
•SOLO
7 SYSTEM SETUP
Specifies the system setup operations that can be performed.
MIXER SETUP
OUTPUT PORT
MIDI/GPI
DANTE SETUP
NOTE
The content that is restricted with the DANTE SETUP button is as shown below.
Changing the CONSOLE ID
Changing the SECONDARY PORT setting
Changing control of DANTE PATCH changes (THIS CONSOLE or DANTE CONTROLLER)
Changing BIT DEPTH
Changing LATENCY
Changing DEVICE MOUNT
Changing REMOTE HA ASSIGN
Changing the Dante Input Patch
Changing the Dante Output Patch
Changing the Dante Input Patch Library (Changing Store, Recall, Clear, Library Name)
If an operation is restricted, the message “This operation is not allowed.” is displayed at the
bottom of the screen.
With the factory settings, this is turned off (no restrictions).
8 SET ALL/CLEAR ALL button
Permits/clears all items.
Preferences
Follow the steps below to make various settings for the CL console operating environment,
such as how windows appear, and whether [SEL] key on/off operations will be linked. These
settings are changed for the user who is logged-in, but if you are logged-in as the
Administrator, you will also be able to change the Guest settings.
NOTE
If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the PREFERENCE for Guest page and make preference settings for the Guest account.
USER SETUP window (PREFERENCE page)
1 STORE/RECALL field
Enables you to turn on or off options related to scene store/recall operations.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the PREFERENCE tab.
4. Use the buttons on screen to make Preference settings.
5. When you have finished making settings, close the window and press the SETUP
button in the Function Access Area.
1
2
3
4
5
Setup
V5 Reference Manual
223
STORE CONFIRMATION
RECALL CONFIRMATION
If these ON buttons are lit, a confirmation message will appear when you perform a
Store or Recall operation respectively.
2 PATCH field
Enables you to turn on or off options related to patch operations.
PATCH CONFIRMATION
If this ON button is lit, a confirmation message will appear when you edit an input patch
or output patch.
STEAL PATCH CONFIRMATION
If this ON button is lit, a confirmation message will appear when you edit an input or
output patch item that is already patched to a port.
3 LOCALE SETUP field
In the SAVE/LOAD screen or RECORDER screen, select a language to be displayed.
JA: Japanese, EN: English, DE: German, FR: French, ES: Spanish
(This does not affect the Help language.)
4 ERROR MESSAGE field
Enables you to specify whether certain error messages should be displayed.
DIGITAL I/O ERROR
If this is on, an error message will appear when a digital audio I/O error occurs.
MIDI I/O ERROR
If this is on, an error message will appear when a MIDI I/O error occurs.
DANTE ALERT
If this is on, an alert message will appear at the bottom of the LCD when the Dante
network is not connecting at gigabit speeds.
If this alert message is displayed, check the following items:
Switch settings
Is the console connected to a switch that does not function at a speed of 1000Mbps?
Are you using a cable that does not support 1000BASE-T?
5 PANEL OPERATION field
Enables you to make settings for options related to panel operation.
AUTO CHANNEL SELECT
Specifies whether the corresponding channel will be selected when you operate the
[ON] key or fader for the channel. You can set this parameter separately for INPUT (input
channels) and OUTPUT (output channels).
•[CUE][SEL] LINK
Specifies whether channel selection will be linked with cue operations. If the LINK
button is on, channels for which cue operations were performed will be selected.
•[FADER BANK][SEL] LINK
Specifies whether channel selection will be linked with fader bank selection. You can set
this parameter separately for INPUT (input channels), OUTPUT (output channels), and
CUSTOM (Custom fader bank).
If the LINK button is on, and you select the corresponding fader bank, the channel in
that bank that was selected most recently will be selected, and its [SEL] key will light.
•[SEND SEL][CUE] LINK
In SENDS ON FADER mode, set whether SEND destination switching and CUE switching
are synchronized. When this is set to off, you can continue to cue a specific channel even
if the SEND destination is switched.
ON KEYS BEHAVIOR DURING MUTE
Sets the operation when pressing the [ON] key during MUTE.
In OVERRIDE mode, when pressing the [ON] key during MUTE, the MUTE is temporarily
canceled and the sound comes out. In CH OFF mode, pressing the [ON] key switches
the channel on/off during MUTE.
IDENTIFY I/O RACK PORT BY [SEL]
Specifies whether to enable a function that allows you to identify the I/O device port
connected to a channel by pressing the [SEL] key for that channel.
If this ON button is lit, pressing a [SEL] key on the panel will cause the signal indicator
to flash for the port of the I/O device that is assigned to the corresponding channel by
the INPUT PATCH/OUTPUT PATCH settings.
POPUP APPEARS WHEN KNOB(S) PRESSED
Specifies whether pressing a knob in the SELECTED CHANNEL section of the panel while
the SELECTED CHANNEL VIEW screen is displayed will cause a window (1ch) to appear.
If the ON button is lit, a window (1ch) will open (or close) whenever you press a knob.
NOTE
If you press the SEND or PAN knob, a window (8ch) will open.
GAIN KNOB FUNCTION
Specifies what will happen when you operate the GAIN knob in the SELECTED
CHANNEL section on the panel. When ANALOG GAIN button is lit, you can adjust
analog gain on the head amp. When DIGITAL GAIN button is lit, you can adjust digital
gain on the console.
•SCENE UP/DOWN
Specifies what the SCENE MEMORY [INC]/[DEC] keys will do when pressed in the
SCENE windows.
When the SCENE +1/-1 button is lit, pressing the [INC] or [DEC] key will increment or
decrement the scene number.
When the LIST UP/DOWN button is lit, pressing the [INC] or [DEC] key will scroll the list
upward or downward.
LIST ORDER
Specifies the order in which scene memories and library items will appear on the list.
When the NORMAL button is lit, the list appears in ascending numerical order. When
the REVERSE button is lit, the list appears in descending numerical order.
Setup
V5 Reference Manual
224
•NAME DISPLAY
Specifies the content of the name display in the Channel Strip section.
When the NAME ONLY button is lit, the channel name and the channel number appear.
Select GR METER to display the GR meter and fader level value.
Select ENCODER INFO to display the information of a function that has been assigned
to the GAIN/PAN/ASSIGN knob on the channel fader strip. This option is the same as
the FULL FUNCTION option in CL version 1.7 or earlier.
NOTE
You can now view the gain reduction meter for DYNAMICS 1 and 2, as well as other information,
on the channel name display.
In addition, if a channel is off during SENDS ON FADER mode, the channel name display will be
highlighted.
The GR meters function enables you to easily view the movement of the gain reduction.
USER DEFINED keys
This section explains how to assign the desired functions to the USER DEFINED keys in the
USER DEFINED KEYS section on the top panel, and to press these keys to execute the
defined function.
If you are logged-in as a user, you can make USER DEFINED key settings for the user. If you
are logged-in as the Administrator, you can also make the USER DEFINED key settings for
the Guest account.
NOTE
For details on the assignable functions and their parameters, refer to “Functions that can be
assigned to USER DEFINED keys” (page 226).
NOTE
If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the USER DEFINED KEYS for Guest page and make USER DEFINED key settings for the Guest
account.
GR meter indicator
Highlighted display
- The channel is off in SENDS ON FADER
mode.
- The channel is assigned to a DCA group, and
that DCA [ON] key is off.
- The channel is assigned to a mute group, and
that mute group master is on.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the USER DEFINED KEYS tab.
4. Press the button corresponding to the USER DEFINED key to which you want to
assign a function.
5. In the FUNCTION field of the USER DEFINED KEY SETUP window, select the function
you want to assign.
6. If the selected function has parameters, press the PARAMETER 1 or 2 field to move
the frame, then select parameters 1 and 2 in the same way.
7. Press the OK button to close the USER DEFINED KEY SETUP window.
8. To execute an assigned function, press the corresponding USER DEFINED [1]-[16]
key on the panel.
USER SETUP screen
(USER DEFINED KEYS page)
USER DEFINED KEY SETUP window
Setup
V5 Reference Manual
225
The 16 buttons in the USER DEFINED KEYS page correspond to USER DEFINED keys [1]-[16]
on the top panel. The name of the function or parameter assigned to each key appears to the
right of the corresponding button. If nothing is assigned to the button, an indication of “---” is
shown.
The list shown in the USER DEFINED KEY SETUP window is the same for all models of the CL
series.
For the CL3/CL1, the display will indicate “Cannot Assign!” if you specify a parameter that does
not exist on that model.
If there are no parameters for the registered USER DEFINED key, nothing will occur when the
key is operated.
Using the Alternate function
If you assign the Alternate function (ALTERNATE FUNCTION) to a USER DEFINED key, you
will be able to switch parameters on or off by operating the knobs in the SELECTED
CHANNEL section while pressing and holding down the USER DEFINED key.
The console enters Alternate mode when you press and hold down the USER DEFINED key
to which the Alternate function has been assigned (the key will light).
The Alternate function features two options: LATCH and UNLATCH.
UNLATCH ..............Alternate mode is turned on only while you are pressing and
holding down the USER DEFINED key.
LATCH ...................Each press of the USER DEFINED key will turn Alternate mode
on or off. You do not need to hold down the key.
NOTE
If you select LATCH for the Alternate function, the console disables the Alternate function when
you switch the display between the OVERVIEW screen and the SELECTED CHANNEL VIEW
screen, or when you open a window.
In Alternate mode, “ALT” will be displayed in the user name field of the Function Access Area.
In Alternate mode, the following knobs change their behavior.
[GAIN] knob
Rotate the knob to adjust the digital gain value. If DIGITAL GAIN has been selected for
HA KNOB FUNCTION on the PREFERENCE page in the USER SETUP window, rotate this
knob to adjust the analog gain value of the head amp.
[MIX/MATRIX] knob
Rotate this knob to switch between PRE and POST for the corresponding send signal.
Press this knob to switch the corresponding send signal on or off.
•[HPF] knob
Press this knob to switch the high-pass filter on or off.
•[DYNAMICS 1] knob
Press this knob to switch DYNAMICS 1 on or off.
•[DYNAMICS 2] knob
Press this knob to switch DYNAMICS 2 on or off.
•[CUE] key
Each time this key is pressed, the channel’s CUE SETTING switches as follows: A
B
A+B.
NOTE
In Alternate mode, all knobs in the SELECTED CHANNEL section other than those knobs
mentioned above will be disabled.
Switching banks for USER DEFINED key settings
You can register the USER DEFINED key settings (16 keys for CL series consoles) to a
maximum of four banks.
Use the four BANK SELECT buttons on the left to select a bank.
The selected bank name is displayed in the field in the bottom right side of the Function
Access Area.
You can press the CLEAR ALL button on the top right side to clear the content of the selected
bank.
Setup
V5 Reference Manual
226
Functions that can be assigned to USER DEFINED keys
FUNCTION
PARAMETER 1 PARAMETER 2 Description
NO ASSIGN - - No assignment.
ALTERNATE
FUNCTION
LATCH -
Toggle ALTERNATE FUNCTION each time it is
pressed.
It goes OFF when the bank is switched.
UNLATCH -
Switch to ALTERNATE FUNCTION only while
pressed.
It goes OFF when the bank is switched.
AUTOMIXER
group a OVERRIDE ON -
Apply a fade-in to the channels in group a
where the override button is on, until the level
drops to 0 dB (the unity gain). Mute all
channels with the button turned off.
group a PRESET ON -
Switch the channels in group a to the mode
indicated by the mode button (man/auto/
mute) next to the lit preset indicator.
group b OVERRIDE ON -
Apply a fade-in to the channels in group b
where the override button is on, until the level
drops to 0 dB (the unity gain). Mute all
channels with the button turned off.
group b PRESET ON -
Switch the channels in group b to the mode
indicated by the mode button (man/auto/
mute) next to the lit preset indicator.
group c OVERRIDE ON -
Apply a fade-in to the channels in group c
where the override button is on, until the level
drops to 0 dB (the unity gain). Mute all
channels with the button turned off.
group c PRESET ON -
Switch the channels in group c to the mode
indicated by the mode button (man/auto/
mute) next to the lit preset indicator.
BRIGHTNESS BANK CHANGE -
Toggle between the brightness settings stored
in A and B.
CH ON SPECIFIC CH *4) Switch the CH ON/OFF.
CH SELECT
INC
-
Increment or decrement the selected channel
number.
DEC
SPECIFIC CH *1) Select a channel from list 1).
CUE
OUTPUT - Switch CUE on/off.
CLEAR CUE
A This clears the CUE for CUE A.
B This clears the CUE for CUE B.
A+B This clears the CUE for CUE A and CUE B.
SPECIFIC CH *2) CUE the channel selected from list 2).
CUE MODE
A
Switches the CUE MODE for CUE A. In Surround
mode, it toggles between MIX, LAST, and 5.1
SOLO with each press. When set to MIX, the
lamp is off. When set to LAST, the lamp is on.
When set to 5.1 SOLO, the lamp flashes.
B Switches the CUE MODE for CUE B.
CUE INTERRUPTION -
Switches the CUE INTERRUPTION function on
or off.
FADER CUE RELEASE -
Switches the FADER CUE RELEASE function on or
off.
CUE
INPUT CUE POINT
A
Selects the cue point for the input channel for
CUE A or CUE B. It toggles between PFL
(immediately before fader), AFL (immediately
after fader), and POST PAN (immediately after
PAN) with each press.
B
DCA CUE POINT
A
Selects the cue point for DCA for CUE A or CUE
B. It toggles between PRE PAN (immediately
before PAN) and POST PAN (immediately after
PAN) with each press.
B
OUTPUT CUE POINT
A
Selects the cue point for the output channel for
CUE A or CUE B. It toggles between PFL (before
fader) and AFL (immediately after fader) with
each press.
B
CUE SETTING
A
For CUE A or CUE B, press the [CUE] key while
holding this key to switch the CUE SETTING for
the selected channel to A or B, and to turn on
the CUE.
B
A+B
Press the [CUE] key while holding this key to
switch the CUE SETTING for the selected
channel to A and B, and to turn on the CUE.
DANTE
INPUT
PATCH LIB
DIRECT RECALL LIBRARY #000-#010
Directly recalls the desired number of the
DANTE INPUT PATCH library. However, it does
not function during a scene recall.
DCA ROLL-
OUT
LAST DCA SEL - This function rolls out or retracts the selected
DCA group.
DCA1 -
:-
DCA16 -
EDITOR
CONTROL
MASTER -
Access the corresponding screen of CL Editor.
SENDS ON FADER -
OVERVIEW
CH 1-16 {CL5/CL3/CL1}
CH17-32 {CL5/CL3/CL1}
CH33-48 {CL5/CL3/CL1}
CH49-64 {CL5/CL3}
CH65-72 {CL5}
ST IN
MIX1-16
MIX17-24
MATRIX
STEREO/MONO
DCA
CUSTOM FADER BANK
A1 {CL5/CL3/CL1}
A2 {CL5/CL3}
A3 {CL3}
B1 {CL5/CL3/CL1}
FUNCTION
PARAMETER 1 PARAMETER 2 Description
Setup
V5 Reference Manual
227
EDITOR
CONTROL
CUSTOM FADER BANK
B2 {CL3/CL1}
Access the corresponding screen of CL Editor.
B3 {CL1}
B4 {CL1}
C1 {CL5}
C2 {CL5}
C3 {CL5}
C4 {CL5}
C5 {CL5}
C6 {CL5}
SELECTED CHANNEL -
LIBRARY
DYNAMICS LIBRARY
INPUT EQ LIBRARY
OUTPUT EQ LIBRARY
EFFECT LIBRARY
GEQ LIBRARY
INPUT CH LIBRARY
OUTPUT CH LIBRARY
PEQ LIBRARY
PREMIUM RACK
LIBRARY
Portico5033 LIBRARY
Portico5043 LIBRARY
Portico5045 LIBRARY
U76 LIBRARY
Opt-2A LIBRARY
EQ-1A LIBRARY
DynamicEQ LIBRARY
Buss Comp 369 LIBRARY
MBC4 LIBRARY
PATCH EDITOR
INPUT PATCH
OUTPUT PATCH
INPUT INSERT PATCH
OUTPUT INSERT PATCH
DIRECT OUT PATCH
PATCH LIST
RACK EDITOR
RACK
GEQ 1-16
EFFECT 1-8
PREMIUM 1A
PREMIUM 1B
:
PREMIUM 8A
PREMIUM 8B
METER
INPUT METER
OUTPUT METER
FUNCTION
PARAMETER 1 PARAMETER 2 Description
EDITOR
CONTROL
GROUP/LINK
DCA GROUP
Access the corresponding screen of CL Editor.
MUTE GROUP
CHANNEL LINK
OUTPUT CHANNEL LINK
SCENE
SCENE MEMORY
RECALL SAFE
FADE TIME
FOCUS RECALL
EFFECT
BYPASS
EFFECT RACK 1-8 -
Turns BYPASS for each RACK on and off. Lit
when ON.
PREMIUM RACK 1A -
PREMIUM RACK 1B -
:-
PREMIUM RACK 8A -
PREMIUM RACK 8B -
FADER BANK
SNAPSHOT
--
Takes a snapshot of the bank settings for all A, B,
and C blocks (hold down the key for two
seconds or longer), or displays the last bank for
which a snapshot was taken (press and release
the key within two seconds).
GAIN KNOB
FUNCTION
LATCH -
Toggle the function of the GAIN knob (ANALOG
GAIN/DIGITAL GAIN). Lit when DIGITAL GAIN is
selected.
It goes OFF when the bank is switched.
UNLATCH -
Assign the function of the GAIN knob (ANALOG
GAIN/DIGITAL) to DIGITAL GAIN only while
held down.
* However if the GAIN KNOB FUNCTION is
switched to DIGITAL GAIN in the PREFERENCE
screen etc., this will remain lit until the next
time it is pressed.
It goes OFF when the bank is switched.
GEQ FREQ
BANK
INC
-
Adds or removes a frequency bank in the GEQ
EDIT screen.
DEC
GPI OUT
LATCH
PORT1-PORT5
Toggle the GPI OUT function. Lit when active.
UNLATCH Make GPI OUT active only while pressed.
HELP - -
Opens and closes the HELP window. Operating
the controllers on the panel (excluding faders),
or controllers on the screen, while holding
down this key will display the related
information.
HOME
SELECTED CH VIEW - Displays the SELECTED CHANNEL VIEW screen.
OVERVIEW - Displays the OVERVIEW screen.
TOGGLE -
Each press of the key will alternately display the
SELECTED CHANNEL VIEW screen and the
OVERVIEW screen.
FUNCTION
PARAMETER 1 PARAMETER 2 Description
Setup
V5 Reference Manual
228
METER
PEAK HOLD ON -
Turns the meter’s peak hold function on/off. Lit
when ON.
SURROUND METER -
For Surround mode, toggle between the
content to be shown in meters displayed in the
Function Access Area. The lamp is off for MIX 1-
6, and on for SURROUND MONITOR.
MIDI
PROGRAM CHANGE PGM 1-128
Transmit the corresponding MIDI message.
For NOTE ON, it goes OFF when the bank is
switched.
CONTROL CHANGE CC 1-31, 33-95, 102-119
NOTE ON
NOTE ON C-2 (0)
:
NOTE ON G 8 (127)
MONITOR
OUTPUT - Switch the monitor output on/off.
SELECTED CH ASSIGN -
While holding down this key, press the SEL key
of a MIX or MATRIX channel to switch the
assignment on/off. During this time, the [SEL]
LED will be lit if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
It goes OFF when the bank is switched.
DIMMER ON -
Enable the dimmer and attenuate the monitor
signal.
SOURCE SELECT
STEREO L/R
Recall the selected signal to the monitor.
MONO (C)
LCR
PB OUT
OMNI1-2
OMNI3-4
OMNI5-6
OMNI7-8
DEFINE
SURROUND SOURCE
SELECT
*6)
Recall the selected signal to the surround
monitor.
SURROUND DOWN-
MIX
STEREO MONO
When this function is off (the lamp is off), the
setting returns to 5.1 monitor.
SURROUND SPEAKER
SOLO
When this function is on (the lamp is on), the
SURROUND MONITOR screen opens. When this
function is off (the lamp is off), the SURROUND
MONITOR screen closes.
L, R, C, Ls, Rs, LFE
This functionality is the same as the SPEAKER
MUTE function in the SURROUND MONITOR
screen. When the SOLO button is on, it
functions as a SOLO key.
MUTE
MASTER
MUTE GROUP 1
- Switch MUTE GROUP MASTER on/off.:
MUTE GROUP 8
ALL MUTE -
Turns all MUTE GROUP MASTER settings on/off
together.
FUNCTION
PARAMETER 1 PARAMETER 2 Description
NUENDO
LIVE
TRANSPORT
GO TO PROJECT START
Operate the transport functions of Nuendo Live.
GO TO PREV MARKER
REWIND
FAST FORWARD
GO TO NEXT MARKER
GO TO PROJECT END
Operate the transport functions of Nuendo Live.
CYCLE
STOP
START
REC
EASY RECORDING
PEAK CLEAR -
Clear the peak indicators of the Nuendo Live
screen.
ADD MARKER -
This function executes ADD MARKER of
NUENDO Live.
OSCILLATOR
OSCILLATOR ON - Switch the OSC on/off.
SELECTED CH ASSIGN -
While holding down this key, press a SEL key of
a channel to switch the assignment on/off.
During this time, the [SEL] LED will be lit if
assign is ON, or dark if OFF.
It goes OFF when the bank is switched.
DIRECT ASSIGN *1)
Assign the oscillator to the channel selected
from list 1).
PAGE
CHANGE
BOOKMARK -
Memorize the currently-selected screen (hold
down the key for two seconds or longer), or
display the last-memorized screen (Hold down
the key, then release it within two seconds).
Popup windows can also be memorized. In the
case of a rack, the number of that rack is also
memorized.
BOOKMARK with “SEL” -
Memorize the above BOOKMARK with the
addition of the SEL status.
PREVIOUS PAGE
- Display the previous/next page.
NEXT PAGE
CLOSE POPUP - Close the displayed window.
FUNCTION
PARAMETER 1 PARAMETER 2 Description
Setup
V5 Reference Manual
229
RECORDER
TRANSPORT
PLAY/PAUSE, STOP,
FF/NEXT,
REW/PREVIOUS, REC
Recorder transport functions.
AUTO REC
Shortcut function for STOP REC PLAY.
Recording will be initiated in a single action. If
this is executed during recording, the file being
recorded will first be closed, and then recording
will continue with a new file.
REC & START
Start recording immediately without entering
record-ready mode.
DIRECT PLAY
NO ASSIGN The specified audio file will be played once from
the beginning.
Audio files to be played should be saved in the
SONGS folder inside the YPE folder. Please note
that a file cannot be specified if it is saved in the
root directory or in any other folder. When you
execute playback, the path in the TITLE LIST
screen will move to \YPE\SONGS\.
(TITLE 1)
:
SCENE
INC RECALL - Recall the scene of the next existing number.
DEC RECALL - Recall the scene of the previous existing number.
DIRECT RECALL SCENE #000-#300 Directly recall the scene of the specified number.
RECALL UNDO - Execute RECALL UNDO.
STORE UNDO - Execute STORE UNDO.
INC - Select the scene of the next existing number.
DEC -
Select the scene of the previous existing number.
RECALL -
This function recalls the currently-selected scene.
STORE - Store the current settings.
SEND MODE
MIX1-16/MIX17-24,
MTRX
-
If INPUT or ST IN is selected, switch the function
of the Selected Channel section’s send encoders
from TO MIX1-16, TO MIX17-24, and MATRIX.
SENDS ON
FADER
MIX1-MIX24
NORMAL/WITH CUE
This function switches between the normal
function on/off (NORMAL), and the function
with cue on/off (WITH CUE). With the WITH
CUE option, cue will be enabled if SENDS ON
FADER mode is engaged or if you switch mode
during SENDS ON FADER mode. Also, with the
WITH CUE option, cue for all output channels
will be canceled if SENDS ON FADER mode is
disengaged.
MTRX 1-MTRX 8
MIX ON FADER
MATRIX ON FADER
SENDS ON FADER
SET BY SEL
+48V
-
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on or
dark if off.
If [PRE SEND] is selected, SEND ON FADER”
mode is engaged while you are holding down
the [SEL] key.
Press SEL to switch between auto/man if
[AUTOMIXER AUTO/MAN] is selected. It goes
OFF when the bank is switched.
Ø
INSERT ON
DIRECT OUT ON
PRE SEND
TO STEREO
TO MONO
TO LCR
GAIN COMPENSATION
AUTOMIXER AUTO/
MAN
FUNCTION
PARAMETER 1 PARAMETER 2 Description
SET DEFAULT
VALUE
--
Press and hold this key, and then press any of
the following knobs on the panel to reset that
knob to its default value: a knob in the
SELECTED CHANNEL section, a knob in the
SELECTED CHANNEL VIEW screen, or a knob in
the Centralogic section.
It goes OFF when the bank is switched.
SET NOMI-
NAL VALUE
--
While holding down this key, press a [SEL] key
to set the fader of that channel to nominal level.
You can also push a knob in the SEND field of
the SELECTED CHANNEL VIEW screen to set the
send level to nominal level.
It goes OFF when the bank is switched.
SOLO SOLO ON - Switches solo mode on/off.
SURROUND
PAN
L ON
*5)
In Surround mode, this is used to switch the bus
assign on and off for the channel selected in list
5).
R ON
C ON
LFE ON
Ls ON
Rs ON
PANNING L
*5)
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
PANNING R
PANNING Front Center
PANNING Ls
PANNING Rs
PANNING Back
PANNING Side L
*5)
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
PANNING Side R
PANNING Center
PANNING TOGGLE *5)
In Surround mode, this is used to toggle the
settings for hard panning for the channel
selected in list 5).
With each press, the setting is toggled in the
following order: Center L Front Center R
Side R Rs Back, Ls Side L (Center).
TALKBACK
TALKBACK ON
LATCH Switch TALKBACK on/off.
UNLATCH
Turn TALKBACK on while pressed.
It goes OFF when the bank is switched.
SELECTED CH ASSIGN -
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be lit
if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
It goes OFF when the bank is switched.
FUNCTION
PARAMETER 1 PARAMETER 2 Description
Setup
V5 Reference Manual
230
*1) CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1L-ST IN 8R, MIX1-MIX24, MTRX1-MTRX8, ST L, ST
R, MONO
*2) CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-MTRX8, STEREO,
MONO(C)
*3) MIX1-MIX24, MTRX1-MTRX8, ST L, ST R, MONO
*4) CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-MTRX8, STEREO,
MONO(C), DCA1-DCA16
*5) SELECTED CH, CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1L-ST IN 8R
*6) MIX1-6, EXT5.1 1, EXT5.1 2, EXT5.1 3, EXT ST 1, EXT ST 2, EXT ST 3, EXT ST 4, MIX1/2, MIX3/4, MIX5/6,
MIX7/8, MIX9/10, MIX11/12, MIX13/14, MIX15/16, MIX17/18, MIX19/20, MIX21/22, MIX23/24, MATRIX1/2,
MATRIX3/4, MATRIX5/6, MATRIX7/8, STEREO, MONO, PB OUT
TALKBACK
DIRECT ASSIGN *3)
The operations performed when this key is
pressed are as follows.
- Toggle assignment of channel selected in list
3) ON and OFF.
At this time, the LED display is as shown below.
- If the channel is assigned, the LED will be on.
Otherwise, the LED will be off.
DIRECT ASSIGN WITH
ON
*3)
The operations performed when this key is
pressed are as follows.
- Assignments other than for the channel
selected in list 3) are removed.
- If a channel is assigned and TALKBACK is ON
at the same time, TALKBACK is turned OFF
and the channel assignment is removed.
- Otherwise, TALKBACK will be ON and the
channel assignment will be ON.
At this time, the LED display is as shown below.
- If the channel is assigned and TALKBACK is ON
at the same time, the LED will be on.
- Otherwise, the LED will be off.
TAP TEMPO
CURRENT PAGE -
Use the tap tempo function in the displayed
screen.
EFFECT RACK 1-8
WITH POPUP
Use the tap tempo function for the specified
effect. If WITH POPUP is selected, the Tap
Tempo screen is displayed. If WITHOUT POPUP
is selected, the Tap Tempo screen is not
displayed.
WITHOUT POPUP
USER
DEFINED
KEYS
BANK SELECT
BANK A
When selected, the lamp for the corresponding
key comes on.
BANK B
When selected, the lamp for the corresponding
key comes on.
BANK C
When selected, the lamp for the corresponding
key comes on.
BANK D
When selected, the lamp for the corresponding
key comes on.
PREVIOUS BANK
Switches to the previous bank. If the current
bank is BANK A, it switches to BANK D.
NEXT BANK
Switches to the next bank. If the current bank is
BANK D, it switches to BANK A.
FUNCTION
PARAMETER 1 PARAMETER 2 Description
Setup
V5 Reference Manual
231
USER DEFINED knobs
This section explains how to assign the desired functions to the USER DEFINED knobs in the
USER DEFINED KNOBS section on the top panel, and press these knobs to execute the
defined function.
If you are logged-in as a user, you can make USER DEFINED knob settings for the user. If
you are logged-in as the Administrator, you can also make the USER DEFINED knob settings
for the Guest account.
NOTE
For details on the assignable functions and their parameters, refer to “Functions that can be
assigned to USER DEFINED knobs” (page 232).
NOTE
If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the USER DEFINED KNOBS and ASSIGNABLE ENCODER for Guest page and make USER
DEFINED knob settings for the Guest account.
The 4 knobs in the USER DEFINED KNOBS and ASSIGNABLE ENCODER page correspond to
USER DEFINED knobs [1]-[4] on the top panel. The name of the function or parameter assigned
to each knob appears to the right of the corresponding button. If nothing is assigned to the button,
an indication of “---” is shown.
The list shown in the USER DEFINED KNOB SETUP window is the same for all models of the CL
series.
For the CL3/CL1, the display will indicate “Cannot Assign!” you specify a parameter that does not
exist on that model.
If there are no parameters for the registered USER DEFINED knob, nothing will occur when the
knob is operated.
About TOUCH AND TURN
The TOUCH AND TURN function is assigned to the USER DEFINED [4]
knob by default. If this function is assigned to one of the USER DEFINED
knobs, you can press a desired knob in the touch screen and then
immediately use the USER DEFINED knob to operate it.
At this time, a pink frame is shown around the knob in the touch screen,
indicating that you can operate that knob.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the USER DEFINED KNOBS tab.
4. Press the button corresponding to the USER DEFINED knob to which you want to
assign a function.
5. In the USER DEFINED KNOB SETUP window, make sure that the FUNCTION field is
enclosed by a frame, then select the function that you want to assign.
6. If the selected function has parameters, press the PARAMETER 1 or 2 field to move
the frame, then select parameters 1 and 2 in the same way.
7. Press the OK button to close the USER DEFINED KNOB SETUP window.
8. To execute an assigned function, press the corresponding USER DEFINED [1]-[4]
knob on the panel.
USER SETUP screen
(USER DEFINED KNOBS page)
USER DEFINED KNOB SETUP window
Setup
V5 Reference Manual
232
Functions that can be assigned to USER DEFINED
knobs
Function
PARAMETER 1 PARAMETER 2
NO ASSIGN - -
AUTOMIXER WEIGHT *1)
BRIGHTNESS
LAMP -
PANEL -
SCREEN -
CH COLOR -
NAME -
CUE
INPUT PFL TRIM
A
B
DCA TRIM
A
B
OUTPUT PFL TRIM
A
B
CUE LEVEL -
DIRECT OUT LEVEL LEVEL *14)
DYNAMICS 1
THRESHOLD *2)
RANGE *4)
RATIO
*2)
ATTACK
HOLD
*4)
DECAY
RELEASE
*2)OUTGAIN
KNEE
WIDTH *13)
DYNAMICS 2
THRESHOLD
*4)
RATIO
FREQUENCY
ATTACK
RELEASE
OUTGAIN
KNEE
WIDTH
EFFECT
Displays the EFFECT RACK No. (1-8) for
the target operation as well as the
name of the mounted EFFECT TYPE or
the name of the GEQ/PEQ TYPE *a).
Displays the names of the 32 parame-
ters for the EFFECT TYPE *b). Displays
“----” if a GEQ/PEQ is mounted.
EQ
ATT
*2)
LOW Q
LOW FREQUENCY
LOW GAIN
LOW MID Q
LOW MID FREQUENCY
LOW MID GAIN
HIGH MID Q
HIGH MID FREQUENCY
HIGH MID GAIN
HIGH Q
HIGH FREQUENCY
HIGH GAIN
EXTERNAL HA GAIN1-GAIN8 *10)
HPF FREQUENCY *4)
I/O DEVICE GAIN1-GAIN32 *11)
INPUT DELAY DELAY TIME *3)
INPUT GAIN
ANALOG GAIN
*4)
DIGITAL GAIN
MIDI CONTROL CHANGE
CTRL 1-CTRL 31 -
CTRL 33-CTRL 95 -
CTRL 102-CTRL 119 -
MONITOR
DIMMER LEVEL -
TALKBACK DIMMER LEVEL -
MONITOR DELAY -
MONITOR FADER -
OSCILLATOR
LEVEL -
FREQUENCY -
LEVEL(EVEN) -
FREQUENCY(EVEN) -
HPF -
LPF -
WIDTH -
INTERVAL -
OUTPUT LEVEL LEVEL *6)
OUTPUT PORT
DELAY TIME
*12)
GAIN
PREMIUM RACK
Displays the PREMIUM RACK No. (1A-
8B) for the corresponding operation, as
well as the name of the mounted PRO-
CESSOR *a).
Displays the names of the 64 parame-
ters for the PROCESSOR *b).
Function
PARAMETER 1 PARAMETER 2
Setup
V5 Reference Manual
233
*1) SELECTED CH, Automixer ch1-16
*2) SELECTED CH, CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1-ST IN 8, MIX1-MIX24, MTRX1-
MTRX8, STEREO, MONO (C)
*3) SELECTED CH, CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1L-ST IN 8R
*4) SELECTED CH, CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1-ST IN 8
*5) SELECTED CH, CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1L-ST IN 8R, MIX1-MIX24
*6) MIX1-MIX24, MTRX1-MTRX8, ST L, ST R, MONO
*7) SELECTED CH, CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48, ST IN 1L-ST IN 8R, MIX1-MIX24, ST L, ST
R, MONO
*10) # 1-# 6
*11) REMOTE HA #1-#8
*12) DANTE 1-DANTE64, OMNI 1-OMNI 8, SLOT1 1-SLOT1 16, SLOT2 1-SLOT2 16, SLOT3 1-SLOT3 16, DIGITAL
OUT L, DIGITAL OUT R
*13) SELECTED CH, MIX1-MIX24, MTRX1-MTRX8, STEREO, MONO (C)
*14) SELECTED CH, CL5: CH1-CH72, CL3: CH1-CH64, CL1: CH1-CH48
*a) If not mounted in the RACK, “----” is displayed.
*b) If there are no parameters, “----” is displayed.
RECORDER
INPUT GAIN -
OUTPUT GAIN -
SCENE SELECT -
TO MIX LEVEL MIX1-MIX24 *3)
TO MATRIX LEVEL MTRX1-MTRX8 *7)
TO MIX PAN MIX1/2-MIX23/24 *3)
TO MATRIX PAN MATRIX1/2-MATRIX7/8 *7)
TO ST/MONO
PAN/BAL
*5)
CSR
TOUCH AND TURN - -
Function
PARAMETER 1 PARAMETER 2
Setup
V5 Reference Manual
234
Assignable encoders
You can assign the desired function to the GAIN/PAN/ASSIGN knob on the fader strip of each
channel, and control the function using the knob. For details on the assignable functions and
their parameters, refer to “Functions that can be assigned to the assignable encoders
(page 235).
NOTE
If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the USER DEFINED KNOBS and ASSIGNABLE ENCODER for Guest page and make
assignable knob settings for the Guest account.
SELECTED SEND is the default setting. If SELECTED SEND is selected, you can use the
assignable encoders to adjust the send level to the MIX/MATRIX channel that is selected for
SENDS ON FADER in the Function Access Area.
The CL3 and CL1 have only one [GAIN/PAN/ASSIGN] key, so the function
of all GAIN/PAN/ASSIGN knobs will change simultaneously. On the CL5,
you can switch the knob function in block A (left side) and block C/Master
fader section (right side) independently by using the corresponding [GAIN/
PAN/ASSIGN] keys.
This assignment does not apply to the multifunction knobs in the
Centralogic section, since these knobs are used to control on-screen
parameters.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the USER DEFINED KNOBS tab.
4. Press the button in the ASSIGNABLE ENCODER field on the USER DEFINED KNOB
page.
5. In the ASSIGNABLE ENCODER SETUP window, select the function you want to
assign.
6. Press the OK button to close the ASSIGNABLE ENCODER SETUP window.
7. Press the [GAIN/PAN/ASSIGN] key on the top panel repeatedly to select ASSIGN.
8. Operate the GAIN/PAN/ASSIGN knob on each channel strip.
USER SETUP screen
(USER DEFINED KNOBS and
ASSIGNABLE ENCODER page)
ASSIGNABLE ENCODER
SETUP window
Setup
V5 Reference Manual
235
Functions that can be assigned to the assignable
encoders
*1 Preference setting and the state of the ALTERNATE function will determine whether this will be analog gain or
digital gain.
*2 The send destination that is the target of Sends On Fader will be selected.
*3 The state of the ALTERNATE function will determine whether turning the encoder will switch the PRE/POST
setting of the corresponding send or will switch the corresponding send on/off when pressed.
*4 The state of the ALT function will determine whether pressing the encoder will switch the high-pass filter on/off.
*5 The state of the ALTERNATE function will determine whether pressing the encoder will switch DYNAMICS 1 on/off.
*6 The state of the ALTERNATE function will determine whether pressing the encoder will switch DYNAMICS 2 on/off.
*7 The state of the ALTERNATE function will determine whether turning the encoder will switch to F/R.
*8 The state of the ALTERNATE function will determine whether turning the encoder will switch to L/R.
PAN GAIN ASSIGN
Function
PARAMETER 1 PARAMETER 2
O PAN/BALANCE
PAN
BAL
O ANALOG GAIN A.GAIN *1
O DIGITAL GAIN D.GAIN *1
ONO ASSIGN
(Nothing will be
displayed.)
O SELECTED SEND
MIX1-MTRX8
Depends on
status
*2
OMIX1 SEND MIX1 *3
OMIX2 SEND MIX2 *3
OMIX3 SEND MIX3 *3
OMIX4 SEND MIX4 *3
OMIX5 SEND MIX5 *3
OMIX6 SEND MIX6 *3
OMIX7 SEND MIX7 *3
OMIX8 SEND MIX8 *3
OMIX9 SEND MIX9 *3
O MIX10 SEND MIX10 *3
O MIX11 SEND MIX11 *3
O MIX12 SEND MIX12 *3
O MIX13 SEND MIX13 *3
O MIX14 SEND MIX14 *3
O MIX15 SEND MIX15 *3
O MIX16 SEND MIX16 *3
O MIX17 SEND MIX17 *3
O MIX18 SEND MIX18 *3
O MIX19 SEND MIX19 *3
O MIX20 SEND MIX20 *3
O MIX21 SEND MIX21 *3
O MIX22 SEND MIX22 *3
O MIX23 SEND MIX23 *3
O MIX24 SEND MIX24 *3
O MATRIX1 SEND MTRX1 *3
O MATRIX2 SEND MTRX2 *3
O MATRIX3 SEND MTRX3 *3
O MATRIX4 SEND MTRX4 *3
O MATRIX5 SEND MTRX5 *3
O MATRIX6 SEND MTRX6 *3
O MATRIX7 SEND MTRX7 *3
OMATRIX8 SEND MTRX8 *3
O HPF FREQUENCY HPF *4
O DYNAMICS1 THRESHOLD THRE1 *5
O DYNAMICS2 THRESHOLD THRE2 *6
O DIGITAL GAIN D.GAIN
OEQ ATT ATT
OINPUT DELAY DELAY
Units of scale
are m, ms, ft,
and fr. No
description for
samples.
O DIRECT OUT LEVEL D.OUT
OSURROUND L-R PAN L/R *7
OSURROUND F-R PAN F/R *8
O SURROUND ROUND PAN L/R and F/R
OSURROUND DIV DIV
O SURROUND LFE LFE
PAN GAIN ASSIGN
Function
PARAMETER 1 PARAMETER 2
Setup
V5 Reference Manual
236
GAIN/PAN/ASSIGN knob (assignable encoder)
functions
In CL V1.7 and later, the following functions have been added to SENDS ON FADER mode.
When using the [GAIN/PAN/ASSIGN] keys on the top panel to select
ASSIGN
Use assignable encoders to adjust the level of channels.
Channel name display indication
When using the [GAIN/PAN/ASSIGN] keys on the top panel to select
PAN
Use assignable encoders to adjust PAN sent from channels to the MIX/MATRIX bus (bus set
for Stereo send in the BUS SETUP screen).
Channel name display indication
Custom fader bank
Groups that organize channels routed to the top-panel faders are called “fader banks.
There are input and output channel banks, as well as custom fader banks. Custom fader
banks enable you to select various combinations of channels, regardless of channel types.
This section explains how to set up a custom fader bank.
NOTE
If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the CUSTOM FADER BANK/MASTER FADER for Guest page, and make custom fader bank
settings for the Guest account.
You can also press the fader assign select buttons to assign channels to faders.
Channel levels
Adjust with assignable encoder.
Send level to MIX/MATRIX bus
Adjust with the fader on the top panel.
PAN sent from channel to MIX/MATRIX bus
Adjust with assignable encoder.
Send level to MIX/MATRIX bus
Adjust with the fader on the top panel.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the CUSTOM FADER tab.
4. Use the Bank Select keys to recall the fader settings to the top panel for the channels
you want to add to the custom fader bank.
5. In the CUSTOM FADER BANK/MASTER FADER page, press the bank select button for
the custom fader bank you want to set up.
6. In the FADER field, press the select button for the fader you want to set up.
7. Press a [SEL] key on the top panel to assign a channel to the fader number selected
in step 6.
8. To assign channels to other faders, repeat steps 5 through 7.
USER SETUP window (CUSTOM
FADER BANK/MASTER FADER page)
Setup
V5 Reference Manual
237
USER SETUP screen
(CUSTOM FADER BANK/MASTER FADER page)
1 Bank select buttons
Enable you to select a custom fader bank to which you want to assign a group of
channels.
The number and name of the custom fader banks vary depending on the console
model.
CL5: A1, A2, B1, C1, C2, C3, C4, C5, C6
CL3: A1, A2, A3, B1, B2
CL1: A1, B1, B2, B3, B4
2 MASTER button
Press this button to set channels that will be controlled by the faders in the Master fader
section.
3 Block indicators
Display the graphics of the top panel block and faders that are the current target for
editing.
The graphics vary depending on the console model.
CL5: A (16 faders), B, C, MASTER
CL3: A (16 faders), B, MASTER
CL1: A (8 faders), B, MASTER
4 Fader select button
Selects the target fader. Press this button to select it, then press [SEL] keys on the top
panel to add the corresponding channels to the selected fader bank.
5 Fader assign select button
Opens the Fader assign select window, in which you can change the channel assigned
to the fader.
6 CLEAR ALL button
Clears all the current fader bank assignment. Pressing this button will open a
confirmation dialog box. Press OK to clear the assignment. Otherwise, press CANCEL to
return to the previous screen without changing the setting.
Master fader
You can set the channels that will be controlled by the two faders in the Master fader section.
NOTE
If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the CUSTOM FADER BANK/MASTER FADER for Guest page, and make master fader settings
for the Guest account.
1
2
6
4
3
5
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the CUSTOM FADER tab.
4. In the CUSTOM FADER BANK/MASTER FADER page, press the MASTER button.
5. In the FADER field, press the number button for the fader you want to set up.
6. Press a [SEL] key on the top panel to assign a channel to the fader number selected
in step 5.
USER SETUP window (CUSTOM
FADER BANK/MASTER FADER page)
Setup
V5 Reference Manual
238
Custom fader bank functions
Custom fader bank settings can be stored/recalled for individual scenes.
Custom fader bank settings are stored in scene data in separate regions for each model.
NOTE
Custom fader bank settings differ between models, and are not compatible. For example, custom
fader bank settings included in scenes stored in CL5 cannot be reproduced if that same scene is
recalled in CL3 or CL1. You must create and store custom fader bank settings in CL3 and CL1.
Precautions for when Loading Console Data
In V2.0 and later, custom fader bank settings are not only included in user settings, but in
scene data as well. The custom fader bank settings that are called up vary depending on the
logged-in user, the type of the loaded data, and the version. Please note the following points:
If you load console data of the ALL type as Administrator, the custom fader bank settings
for the saved Administrator are called up.
If you load ALL data as Guest or another user, the custom fader bank settings for the saved
current scene are called up.
If you load ALL data that was saved in CL V1.70 or earlier, since scenes do not include
custom fader bank settings, the custom fader bank settings for the current scene when the
load was performed are applied to all scenes. Therefore, before loading ALL data, we
recommend that you either change users to set the custom fader bank to the desired
setting, or that you enable Recall Safe for the custom fader bank.
Console Lock
You can temporarily prohibit console operations in order to prevent unwanted operation. This
setting disables operations of the panel, so that controllers cannot be operated by an
accidental touch or by an unauthorized third party while the operator is taking a break.
If a password is set for the currently logged-in user, that password will be used for the Console
Lock function. When the Console Lock function is enabled, the CONSOLE LOCK screen will
appear and all controllers (excluding the MONITOR LEVEL knob) will become inoperable.
NOTE
If you have forgotten the password, refer to “Initializing the unit to factory default settings
(page 278).
The Guest cannot set a password.
Even while the console is locked, control from an external device via MIDI or CL Editor will still
operate as usual.
CL5
CL5 console
Recall Store Recall Store Recall Store
CL3 CL1
CL3 console CL1 console
Custom fader bank settings
Setup
V5 Reference Manual
239
Locking the console
Unlocking the console
NOTE
If you are logged-in as a user for whom no password is set, the console will be unlocked when
you touch the CONSOLE LOCK screen.
Specifying the CONSOLE LOCK screen image
If an image file has been saved on the USB flash drive, you can view that image on the
CONSOLE LOCK screen.
In the SAVE/LOAD window, specify the image file that you want to display, and then load it
from the USB flash drive. For details about loading files from the USB flash drive, refer to
Loading a file from a USB flash drive” (page 242).
NOTE
Supported image file format is BMP in 800 x 600 pixels and 16/24/32-bit, but they will be
converted into 16-bit for display.
Saving and loading setup data to and from a USB
flash drive
You can connect a commercially-available USB flash drive to the USB connector located to
the right of the display, and save the internal settings and user authentication keys of the CL
series console to the USB flash drive or load them from the USB flash drive.
CAUTION
An ACCESS indicator is shown in the Function Access Area while data is being accessed (saved,
loaded, or deleted). During this time, do not disconnect the USB port or power-off the CL unit.
Doing so may damage the data in the flash drive.
NOTE
Operation is guaranteed only for USB flash drives.
The operation of USB flash drives with capacities of up to 32GB has been verified. (However, this
does not necessarily guarantee the operation of all USB flash drives.) The FAT16 and FAT32
formats are supported. A USB flash drive with a capacity of 4GB or larger will be formatted in
FAT32, and a USB flash drive with a capacity of 2GB or smaller will be formatted in FAT16.
Basic operation
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the CONSOLE LOCK button.
3. If you are logged-in as a user for whom a password is set, enter the password for the
user.
4. Press the OK button to enable Console Lock function.
STEP
1. Press the CONSOLE LOCK screen.
2. If you are logged-in as a user for whom a password is set, enter the password for the
user, then press the OK button.
SETUP screen
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the SAVE/LOAD button.
3. Save/load/edit the data.
SETUP screen
Setup
V5 Reference Manual
240
SAVE/LOAD window
The list will show the files and sub-directories that have been saved.
1 COPY button
Copies a file into a memory buffer (a temporary holding area).
2 PAST E bu tton
Pastes the file that has been copied into a buffer memory.
3 DELETE button
Deletes the currently selected file.
NOTE
A directory cannot be deleted unless it is empty. The message “Directory Not Empty!” will appear.
4 MAKE DIR button
Creates a new directory.
5 PATH
Indicates the name of the current directory. Press the arrow button to move to the next
higher level. If the current directory is the top level, the arrow button is dimmed.
6 VOLUME NAME/FREE SIZE
Indicates the volume name and the amount of free space on the USB flash drive. If the
USB flash drive is write-protected, a protect symbol will appear in the VOLUME NAME
field.
7 File list
This area lists the files and sub-directories that are saved on the USB flash drive. The
highlighted line indicates the file selected for operations.
The file list contains the following items. When you press an item name, it will turn
orange, and the list will be sorted by that item. Each time you press the item name, the
sorting order will alternate between ascending and descending order.
FILE NAME.................Indicates the file name or directory name, and shows an icon
indicating its type.
COMMENT .................The comment added to the CL console setting file is displayed
here. You can press this area to open a keyboard window,
allowing you to enter a comment for the file.
READ ONLY ...............A lock symbol in this column indicates that the corresponding
file is protected. You can press this area to enable or disable
the protect setting.
Protected files cannot be overwritten.
TYPE...........................Indicates the file type.
ALL: File containing CL internal settings
KEY: User authentication key
XML: Help file
BMP: Bitmap image file
MP3: MP3 file
[DIR]: Directory
NOTE
If the file format version is earlier than V1.70, “old” is displayed in the
second line of this field. Data can be loaded even if “old” is displayed.
If the console version is V2 or later, data from any version can be
loaded.
TIME STAMP .............. Indicates the date and time at which the file was modified most
recently.
8 File selection knob
Selects a file on the file list. You can operate this knob using the multifunction knob.
9 SAVE button
Saves all of the CL console internal settings together (page 241).
0 LOAD button
Loads the selected CL setting file (page 242).
A CREATE USER KEY button
Creates a user authentication key (page 216).
B FORMAT button
Initializes the USB flash drive (page 245).
If an overcurrent condition occurred at the USB port, this button will become a USB
REMOUNT button. Press this button to remount a USB flash drive (page 246).
1 2 3 45 6
7
8 9 0 A BC
Setup
V5 Reference Manual
241
C WITH DANTE SETUP AND I/O RACK button
If this is off, the DANTE SETUP and I/O device settings as well as word clock settings will
be omitted when a settings file is loaded.
NOTE
The DANTE SETUP settings SECONDARY PORT and CONSOLE ID will not be changed even
if the “WITH DANTE SETUP AND I/O RACK” button is on.
Saving the CL console’s internal data on a USB flash drive
All of the CL series console’s internal data can be saved on a USB flash drive as a setting file.
The saved file will have an extension of “.CLF”.
SAVE SELECT screen
1 TYPE field
Specifies the types of data to be saved. The view of the TYPE field will vary depending
on the tab you select.
•ALL tab
This button selects all the items.
•SCENE tab
This button selects scene memories.
INPUT/OUTPUT tab
The following table lists the items that you can select.
EFFECT/GEQ tab
The following table lists the items that you can select.
PREMIUM tab
The following table lists the items that you can select.
STEP
1. In the SAVE/LOAD window, press the SAVE button.
2. In the SAVE SELECT screen, select the data to be saved, the data type, and the save
destination.
3. In the SAVE SELECT screen, press the SAVE button.
4. Enter a file name and comment.
5. Press the SAVE button to execute the Save operation.
1
47654
2 3
Button Data content
IN CH LIB Input channel library
OUT CH LIB Output channel library
IN EQ LIB Input EQ library
OUT EQ LIB Output EQ library
DYNA LIB Dynamics library
Button Data content
EFFECT LIB Effect library
GEQ LIB GEQ library
8PEQ LIB 8Band PEQ library
Button Data content
5033 LIB Portico 5033 library
5043 LIB Portico 5043 library
5045 LIB Portico 5045 library
U76 LIB U76 library
Opt-2A LIB Opt-2A library
EQ-1A LIB EQ-1A library
DynaEQ LIB DynamicEQ library
BussComp LIB Buss Comp 369 library
MBC4 LIB MBC4 library
Setup
V5 Reference Manual
242
SETUP tab
The following table lists the items that you can select.
NOTE
When the output port items are saved individually, channel assignments for the port will not be
saved. To prevent this, save the scene that contains input/output patching for the channel
assignment as well.
2 SOURCE field
Indicates the internal data of the CL series console.
3 DESTINATION field
Indicates the save destination.
4 Data selection knob
This knob selects the data shown in the field.
5 MULTI SELECT button
Press this button to make a selection containing multiple items of data.
6 SELECT ALL button
Press this button to select all items.
7 CLEAR ALL button
Press this button to clear all selections.
NOTE
To select a different directory as a save destination, in the SAVE/LOAD window, press a directory
icon or press the arrow button in the PATH field.
If you are going to overwrite a file or save a file with the same name in the same folder, a dialog
will ask you to confirm the overwrite.
You can enter a comment of up to 32 characters.
You may enter a file name of more than eight characters. However, the drive name, path name,
and file name are limited to a total of 256 characters. If you exceed this limit, you may be unable
to save the file, depending on the length of the file name. If this error indication appears at the
bottom of the screen, shorten the file name and try saving the file again.
Loading a file from a USB flash drive
Follow the steps below to load a CL settings file (extension .CLF) from the USB flash drive into
the CL series console.
You can use the same procedure to load the following files as well as settings files.
CAUTION
Some data may contain settings that will cause the console to output signals immediately after
the data is loaded. Before you load, turn off the power of the equipment connected to the CL
series console and/or lower the volume of such equipment so that there will not be a problem
even if a signal is output from the CL console.
NOTE
When the file has finished being loaded, the window that shows the progress of the loading
operation and the type of data will close. If you cancel this procedure while it is in progress, data
up to the cancellation point will still be loaded.
Some setting data may not be loaded, depending on the USER LEVEL setting during the load
operation.
Button Data content
MIXER SETUP Mixer setup
OUTPUT PORT Output port
MONITOR CUE/MONITOR/OSCILLATOR/TALKBACK
MIDI SETUP MIDI setup
MIDI PGM MIDI program changes
MIDI CTL MIDI control changes
Dante In Patch Dante input patch library
Extension Type Contents of file
.CLF ALL CL console internal setting file
.CLU KEY CL console user authentication key
.XML XML XML file for displaying Help
.TXT TEXT Text file for displaying Help
.BMP BMP
Image file for display in the CONSOLE LOCK screen (256 or more
colors, uncompressed bitmap format)
STEP
1. To select the file that you want to load, press the name of the desired file in the file
list in the SAVE/LOAD window, or rotate the corresponding multifunction knob.
2. If you want the DANTE SETUP and I/O device-related settings saved in the CL
settings file (file name extension .CLF) and the word clock settings to be applied to
the CL console, press the WITH DANTE SETUP AND I/O DEVICE button to turn it on.
3. In the SAVE/LOAD window, press the LOAD button.
4. In the LOAD SELECT screen, select the data to load, the data type, and the load
destination.
5. Press the LOAD button to load the selected file.
Setup
V5 Reference Manual
243
LOAD SELECT screen
1 TYPE field
Indicates the type of data to be loaded. The view will vary depending on the tab you
select.
NOTE
The console version at the time when the data was saved is displayed on the top right side. If no
data has been saved, “NO DATA” will be displayed. If data has been saved but the version cannot
be determined, “later than V4.00” will be displayed.
ALL tab
This button selects all the items.
•SCENE tab
This button selects scene memories.
INPUT/OUTPUT tab
The following table lists the items that you can select.
EFFECT/GEQ tab
The following table lists the items that you can select.
PREMIUM tab
The following table lists the items that you can select.
SETUP tab
The following table lists the items that you can select.
NOTE
When the output port items are loaded individually, channel assignments for the port will not be
applied. To prevent this, load and then recall the scene that contains input/output patching for the
channel assignment.
Button Data content
IN CH LIB Input channel library
OUT CH LIB Output channel library
IN EQ LIB Input EQ library
OUT EQ LIB Output EQ library
DYNA LIB Dynamics library
1
47654
2
3
Button Data content
EFFECT LIB Effect library
GEQ LIB GEQ library
8PEQ LIB 8Band PEQ library
Button Data content
5033 LIB Portico 5033 library
5043 LIB Portico 5043 library
5045 LIB Portico 5045 library
U76 LIB U76 library
Opt-2A LIB Opt-2A library
EQ-1A LIB EQ-1A library
DynaEQ LIB DynamicEQ library
BussComp LIB Buss Comp 369 library
MBC4 LIB MBC4 library
Button Data content
MIXER SETUP Mixer setup
OUTPUT PORT Output port
MONITOR CUE/MONITOR/OSCILLATOR/TALKBACK
MIDI SETUP MIDI setup
MIDI PGM MIDI program changes
MIDI CTL MIDI control changes
Dante In Patch Dante input patch library
Setup
V5 Reference Manual
244
ADMIN tab
The following table lists the items that you can select.
2 SOURCE field
This area lists the data that is saved on the USB flash drive.
3 DESTINATION field
Indicates the load destination.
4 Data selection knob
This knob selects the data shown in the field.
5 MULTI SELECT button
Press this button to make a selection containing multiple items of data.
6 SELECT ALL button
Press this button to select all items.
7 CLEAR ALL button
Press this button to clear all selections.
Editing the files saved on the USB flash drive
Follow the steps below to perform editing operations such as sorting the files and directories
on the USB flash drive, editing the file names or comments, copying, and pasting.
Sorting files
To sort the files, press one of the headings “FILE NAME,” “COMMENT,” “READ ONLY,
“TYPE,” or “TIME STAMP” at the top of each column on the SAVE/LOAD window. The list will
be sorted as follows, according to the column heading you press.
1 FILE NAME
Sort the list in numerical/alphabetical order of the file names.
2 COMMENT
Sort the list in numerical/alphabetical order of the comment.
3 READ ONLY
Sort the list by Write Protect on/off status.
4 TYPE
Sort the list by file type.
5 TIME STAMP
Sort the list by date and time of update.
NOTE
By pressing the same location again, you can change the direction (ascending order or
descending order) in which the list is sorted.
Editing file names/comments
NOTE
You cannot edit the file name or comment of a write-protected file.
Type Data content
ADMIN PREF PREFERENCE (for the Administrator)
ADMIN UDEF
USER DEFINED KEYS/USER DEFINED KNOBS (for the
Administrator)
ADMIN FADER CUSTOM FADER BANK (for the Administrator)
GUEST PREF PREFERENCE (for the Guest)
GUEST UDEF USER DEFINED KEYS/USER DEFINED KNOBS (for the Guest)
GUEST FADER CUSTOM FADER BANK (for the Guest)
GUEST LEVEL USER LEVEL (for the Guest)
STEP
1. In the SAVE/LOAD window, press the FILE NAME field or COMMENT field of each
file.
2. Enter a file name or comment in the keyboard window, and press the RENAME
button or SET button.
1 2 3 4 5
Setup
V5 Reference Manual
245
Copying and pasting a file
Follow the steps below to copy a desired file into buffer memory, and then paste it with a
different file name.
NOTE
You cannot use a file name that already exists when you paste a file.
Deleting a file
NOTE
You cannot delete a protected file.
Creating a directory
NOTE
You cannot create a directory using a directory name that already exists.
Formatting a USB flash drive
Follow the steps below to format a USB flash drive.
A USB flash drive with a capacity of 4GB or larger will be formatted in FAT32, and a USB flash
drive with a capacity of 2GB or smaller will be formatted in FAT16.
STEP
1. Turn the multifunction knob to select the copy-source file, and press the COPY
button in the SAVE/LOAD window.
2. Press the directory icon or press the arrow button in the PATH field to move to the
directory into which you want to paste the file.
3. Press the PASTE button.
4. Enter the file name, and press the PASTE button.
STEP
1. Rotate the multifunction knob to select a file to delete, then press the DELETE
button in the SAVE/LOAD window.
2. To execute the Delete operation, press the OK button.
STEP
1. Press the directory icon or press the arrow button in the PATH field in the SAVE/
LOAD window to change the directory.
2. Press the MAKE DIR button.
3. Enter the name of the directory you want to create, then press the MAKE button.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the SAVE/LOAD button.
3. In the SAVE/LOAD window, press the FORMAT button.
4. Enter a volume name, and press the FORMAT button.
5. To execute the Format operation, press the OK button.
SAVE/LOAD window
Setup
V5 Reference Manual
246
Recovering after overcurrent at the USB port
Even if the connection with the USB device was stopped because an overcurrent condition
occurred at the USB port, it is possible to use the USB device again without turning the
console power off and back on.
Recovery procedure
After removing the cause of the overcurrent at the USB port, press the location that shows
“USB REMOUNT” at the FORMAT button of the SAVE/LOAD window.
Remount function to USB flash drives
If USB flash drive is not mounted, the FORMAT button will become a USB REMOUNT button.
Press this button to mount a USB flash drive. Use this button if a USB flash drive is not
recognized after it has been removed and reinserted.
Word clock and slot settings
“Word clock” refers to the clock that provides the basis of timing for digital audio signal
processing. To send and receive digital audio signals between devices, those devices must
be synchronized to the same word clock. If digital audio signals are transferred in an
unsynchronized state, the data may not be transmitted or received correctly, and noise may
be present in the signal, even if the sampling rates are the same.
Specifically, you must first decide which device will transmit the reference word clock for the
entire system (the word clock master), and then set the remaining devices (the word clock
slaves) so that they synchronize to the word clock master.
If you wish to use the CL series console as a word clock slave that is synchronized to the word
clock supplied from an external device, you must specify the appropriate clock source (the
port through which the word clock is obtained).
This section explains how to select the clock source that the CL series console will use.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SYSTEM SETUP field of the SETUP screen, press the WORD CLOCK/SLOT
SETUP button.
3. In the MASTER CLOCK SELECT field of the WORD CLOCK/SLOT SETUP window,
select a clock source.
4. Press the “x” symbol located in the upper right to close the window.
SETUP screen WORD CLOCK/SLOT SETUP window
Setup
V5 Reference Manual
247
WORD CLOCK/SLOT SETUP window
MASTER CLOCK SELECT field
1
Master clock frequency display
Indicates the frequency (44.1 kHz or 48 kHz) of the currently-selected master clock. If
the unit is not synching to the master clock, UNLOCK” will appear.
NOTE
If sample rate pull-up/down has been specified in the Dante
Controller application, this area indicates the change in the
sample rate as a percentage, such as -4.0%, -0.1%, +0.1%, and
+4.1667%.
To change the master clock when sample rate pull-up/down has been specified, disable the pull-
up/down in the Dante Controller, change the master clock, then specify pull-up/down again.
2 Master clock select buttons
Use the buttons to select the clock source that you want to use as the word clock master
from the following options:
INT 48 k
INT 44.1 k
The CL console internal clock (sampling rate 48 kHz or 44.1 kHz) will be the clock
source.
WORD CLOCK IN
The word clock supplied from the WORD CLOCK IN jack on the rear panel of the console
will be used as the clock source.
DANTE 48 k
DANTE 44.1 k
The word clock supplied from the Dante jack on the rear panel of the console will be
used as the clock source.
NOTE
With CL V2.03 and later, if you initialize the console to factory settings, the default value for the
word clock is set to DANTE 48k. This allows you to synchronize word clock even when using
multiple CL and QL consoles at their default settings.
•SLOT 1-3
The word clock supplied via a digital I/O card installed in a console slot will be used as
the clock source. Word clock can be selected in pairs for each slot.
3 Clock status Indicator
Indicates the console’s status as a master or a slave in the Dante audio network.
NOTE
When is displayed and the specified word clock is not synchronized
with a device acting as a Dante master, the audio might cut out.
4 Clock status display
Indicates the status of synchronization with the master clock for each clock source. Each
indicator is explained below:
LOCKED (light blue)
Indicates that a clock synchronized with the selected clock source is being input. If an
external device is connected to the corresponding connector or slot, input/output is
occurring properly between that device and the CL series console. If the sampling
frequency is close, this status may be displayed even if not synchronized.
LOCKED, BUT NOT SYNC’ED (yellow)
A valid clock is being input, but is not synchronized with the selected clock source. If an
external device is connected to the corresponding connector, input/output cannot
occur correctly between that device and the CL series console.
SRC ON (green)
This is a special status that applies only to SLOT1-3. It indicates that SCR (Sample Rate
Converter) is enabled for the corresponding channel. This means that even if the signal
is not synchronized, normal input/output with the CL series console is occurring.
UNLOCKED (red)
A valid clock is not being input. If an external device is connected to the corresponding
connector, input/output cannot occur correctly between that device and the CL series
console.
3
1
5
2
4
7
6
8
Master
Slave
Setup
V5 Reference Manual
248
UNKNOWN (black)
This indicates that the clock status cannot be detected because no external device is
connected or because there is no valid clock input. You will be able to select this
connector/slot, but successful synchronization cannot occur until a valid connection is
established.
NOTE
If the indicator for the selected clock does not turn light blue, make sure that the external device
is correctly connected, and that the external device is set to transmit clock data.
Noise may occur at the output jacks when the word clock setting is changed. To protect your
speaker system, be sure to turn down the power amp volume before changing the word clock
setting.
If you attempt to select a channel (for which SRC is on) as the word clock source, a message will
appear, warning you that the sampling rate converter will be disabled.
SLOT SETUP field
This field enables you to make various settings related to the MY slots on the rear panel of the
console.
5 Card name
Indicates the type of card installed in the slot. If nothing is installed,----” will appear.
6 SRC buttons
The SCR (Sampling Rate Converter) function can be switched on or off for a slot in which
an MY card (MY8-AE96S) that features the SRC function is installed. If another type of
card is installed, or if no card is installed, no SRC button will appear.
7 FREQUENCY display
Indicates the sampling frequency of input signals if the installed card can detect the
substatus of input signals, such as an AES/EBU card. If another type of card is installed,
or if no card is installed, ----” will appear.
8 EMPHASIS STATUS display
Indicates the emphasis information of input signals if the installed card can detect the
substatus of input signals, such as an AES/EBU card. If another type of card is installed,
or if no card is installed,----” will appear.
Using cascade connections
Using multiple CL series consoles, or a CL console and an external mixing console (such as
a Yamaha PM5D) in a cascade connection enables buses to be shared among the devices.
This can be convenient if you want to use an external mixer to increase the number of inputs.
This section explains cascade connections and operation, using an example in which two CL
units are connected in a cascade configuration.
About cascade connections
To cascade two CL series consoles, you must first install digital I/O cards in the appropriate
slots, and connect the output ports of the sending unit (the cascade slave) to the input ports
of the receiving unit (the cascade master).
The following illustration shows an example in which three eight-channel digital I/O cards for
each unit are installed in the cascade slave CL unit and in the cascade master CL unit. The
DIGITAL OUT jacks of the sending unit are connected to the DIGITAL IN jacks of the receiving
unit.
In this example, up to twenty four buses chosen from MIX bus 1-24, MATRIX bus 1-8,
STEREO bus (L/R), MONO (C) bus, and CUE bus (L/R) can be shared, and the mixed signals
transmitted from the cascade master CL unit. (If you use three 16-ch digital I/O cards, all
buses can be shared among the devices.) When the required settings are made for the
cascade slave and for the cascade master, the bus signals of the cascade slave will be sent
via the slot to the buses of the cascade master, and the combined signals of both buses will
be output from the cascade master. If the Cascade Link function is enabled, the specified
operations or parameter changes performed on either CL series console will be followed by
the other CL console.
You must specify bus assignments for each slot or channel on each CL unit. The procedure
below is given separately for the cascade slave and the cascade master.
CL BCL A
DIGITAL
OUT
DIGITAL
IN
Audio signals of
A + B
Audio signals of
unit A
Digital I/O card
(Cascade slave) (Cascade master)
Setup
V5 Reference Manual
249
NOTE
In Surround mode, you cannot use cascade output on MIX buses1-6. In addition, if you have
selected 5.1 SOLO in CUE mode, you cannot monitor CUE from the cascade slave at the
cascade master.
If you are making a cascade connection between the CL unit and the PM5D, you can use the CL
unit as the cascade slave by setting the PM5D’s CASCADE IN PORT SELECT to a slot. However,
only the audio signals will be cascaded, and the control signals cannot be linked.
You can also use an AD/DA card to make cascade connections with an analog mixer.
There is no limit to the number of units that can be cascade-connected, but the signal delay at
the cascade slave will increase in accordance with the number of units from the cascade master.
Operations on a cascade slave CL unit
NOTE
You cannot assign two or more buses to the same output port. If you select a port to which a
signal route has already been assigned, the previous assignment will be canceled.
Control signals for the cascade link and MIDI messages cannot share the same port. If you select
a port that is already specified for transmission/reception of MIDI messages, a dialog box will ask
whether it is OK to cancel the existing settings.
CASCADE window (CASCADE OUT PATCH page)
You can select the slot and output port that will output each bus.
1 OUT PATCH buttons (CASCADE OUT PATCH section)
Enable you to select the output port for cascade connections for each of MIX 1-24,
MATRIX 1-8, STEREO L/R, MONO, and CUE L/R buses. Press the button to open the
PORT SELECT window, in which you can select a port.
2 CASCADE LINK buttons
Used to select the operations to be linked when making cascade connections between
CL series consoles. Multiple selection is possible.
•DCA 1-8
The following parameters related to DCA 1 to 8 will be linked.
DCA 1 - 8 level
DCA 1 - 8 on/off
DCA 1 - 8 cue
DCA 1 - 8 DCA MUTE TARGET (DCA group mute targets)
NOTE
Even if the cue mode is LAST CUE, the cue for the target DCA will come on at the same time
for consoles linked by cascade connections.
•DCA 9-16
The following parameters related to DCA 9 to 16 will be linked.
•DCA 9 - 16 level
DCA 9 - 16 on/off
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SYSTEM SETUP field of the SETUP screen, press the CASCADE button.
3. In the CASCADE window, press the CASCADE OUT PATCH tab.
4. In the CASCADE OUT PATCH page, press the OUT PATCH button for the bus to which
you want to assign the port.
5. Use the slot select list and the port select buttons to select the slot and output ports
that you want to assign, and then press the CLOSE button.
6. In the CASCADE COMM PORT field, select the port that will transmit and receive
control signals for cascade link.
7. Use the CASCADE LINK MODE buttons to select the item that you want to link.
3
1
2
4
Setup
V5 Reference Manual
250
DCA 9 - 16 cue
DCA 9 - 16 DCA MUTE TARGET (DCA group mute targets)
NOTE
Even if the cue mode is LAST CUE, the cue for the target DCA will come on at the same time
for consoles linked by cascade connections.
•MUTE MASTER
Links ON/OFF for mute masters.
NOTE
The settings of Dimmer function are not linked. Make these settings individually on each
console.
SENDS ON FADER
Links SENDS ON FADER behavior.
SENDS ON FADER mode
The send destination bus
CUE
The following cue-related parameters and events will be linked.
Cue enable/disable
Cue mode (MIX CUE or LAST CUE, 5.1 SOLO)
NOTE
Regarding 5.1 SOLO, no links are made if the console at the cascade destination is set to
Stereo mode.
Cue point settings for input channels and output channels
Solo mute
NOTE
Solo operation is used for all cascaded consoles (MASTER and SLAVE).
•OTHERS
The following parameters will be linked.
Scene recall operations
Scene store operations
Edit scene titles
DIMMER (MONITOR window) operations
Panel LED and display brightness (SETUP window) operations
3 CASCADE COMM PORT buttons
Specify the communication port used for transmitting and receiving link information
when cue operations or scene store/recall operations are linked on the CL series consoles
in a cascade connection.
NONE.....................No link operation
MIDI........................Use MIDI port
SLOT1....................Use SLOT1
4 Tabs
Switches between pages (CASCADE IN PATCH, CASCADE IN ATT, and CASCADE OUT
PATCH).
PORT SELECT window
Press the OUT PATCH button to open this window.
1 Slot select list
This list selects slots 1-3.
2 Port select buttons
These buttons select the port of the specified slot.
2
1
Setup
V5 Reference Manual
251
CASCADE window (CASCADE IN ATT page)
1 ATT knobs
Display the attenuator values (-96.0dB to 0.0dB) for cascade input signals. You can
adjust these values using multifunction knobs 1 - 8 in the Centralogic section.
NOTE
You can use these knobs as SUB IN with adjustable input level. Doing so allows you to sum the
signals from other consoles to a bus, without using up inputs and buses.
Operations on the cascade master CL unit
NOTE
You can assign the same input port to two or more buses.
Control signals for the cascade link and MIDI messages cannot share the same port. If you select
a port that is already specified for transmission/reception of MIDI messages, a dialog box will ask
whether it is OK to cancel the existing settings.
1
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SYSTEM SETUP field of the SETUP screen, press the CASCADE button.
3. In the CASCADE window, press the CASCADE IN PATCH tab.
4. In the CASCADE IN PATCH page, press the IN PATCH button for the bus to which you
want to assign the port.
5. In the PORT SELECT screen, use the slot select list and the port select buttons to
select the slot and input ports that you want to assign, and then press the CLOSE
button.
6. As described in step 6 of “Operations on a cascade slave CL unit” (page 249), in the
CASCADE LINK PORT field, select the port that will transmit and receive control
signals for cascade link.
7. As described in step 7 of “Operations on a cascade slave CL unit” (page 249), in the
CASCADE COMM LINK field, select the same item as the cascade slave.
Setup
V5 Reference Manual
252
Basic settings for MIX buses and MATRIX buses
Follow the steps below to change the basic settings for MIX buses and MATRIX buses, such
as switching between stereo and monaural, and selecting the send point from which the
signal of an input channel will be sent. The settings you make in the following procedure are
saved as part of the scene.
BUS SETUP window
You can make various settings for MIX buses and MATRIX buses.
1 SIGNAL TYPE switch buttons
Select how signals are processed for every adjacent pair of buses. Select either STEREO
(stereo signal) or MONOx2 (monaural signal x 2).
2 Bus type/send point select buttons (MIX bus only)
For every adjacent pair of buses, you can select the bus type and (for vari-type) the send
point. These buttons correspond to the following parameters.
3 Send point select buttons (MATRIX bus only)
Select the pre-fader send point from the input channel. These buttons correspond to the
following parameters.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the BUS SETUP button.
3. Use the tabs in the BUS SETUP window to select the MIX bus or MATRIX bus.
4. Use the SIGNAL TYPE switch buttons to specify whether each bus will function as
STEREO (main parameters will be linked for two adjacent odd-numbered/even-
numbered buses) or MONOx2 (use as two monaural channels).
5. Use the bus type/send point select buttons to select the bus type and the position
from which the signal of the input channel will be sent.
6. As desired, turn the buttons in the PAN LINK field on or off.
SETUP screen BUS SETUP window
Button Bus type Pre-fader send point
VARI [PRE EQ] VARI Immediately before the EQ
VARI [PRE FADER] VARI Immediately before the fader
FIXED FIXED ---
Button Pre-fader send point
PRE EQ Immediately before the EQ
PRE FADER Immediately before the fader
1 42 1 43
55
MIX 1-16 page MIX BUS 17-24/MATRIX BUS page
Setup
V5 Reference Manual
253
4 PAN LINK button
This button appears if SIGNAL TYPE is set to STEREO and VARI is set. If the button is on,
the pan setting of signals sent from input channels to the corresponding two buses will
link with the STEREO bus pan setting.
5 Tabs
Enable you to switch between the MIX and MATRIX buses.
Switching the entire phantom power supply on/off
NOTE
This +48V MASTER setting does not affect the inputs of external racks such as DANTE inputs (I/
O devices). Each rack has a +48V MASTER switch, and will operate according to its setting.
Specifying the brightness of the touch screen,
LEDs, channel name displays, and lamps
Follow the steps below to specify the brightness of the touch screen, top panel LEDs, channel
name displays, and lamps connected to the rear panel LAMP connectors. You can save two
different brightness settings in bank A and B, and switch between them rapidly if desired.
NOTE
You can also assign this parameter to a USER DEFINED key, and press that key to switch
between banks A and B.
SETUP screen (brightness setting field)
1 BANK A/B buttons
Switch between the brightness settings.
CONTRAST field
2
NAME
Adjusts the contrast of the characters of the channel name displays on the top panel.
BRIGHTNESS field
3
NAME
Adjusts the brightness of the channel name displays on the top panel.
This will also change the CH COLOR brightness. If you want to adjust the CH COLOR
brightness after setting the name display brightness, use the CH COLOR knob.
4 CH COLOR
Adjusts the brightness of the channel colors on the top panel.
This lets you apply a relative adjustment to only the channel color brightness without
changing the channel name display brightness.
STEP
1. In the Function Access Area, press the SETUP button to access the SETUP screen.
2. In the center of the SETUP screen, press the +48V MASTER field’s ON button or OFF
button.
If this button is off, phantom power will not be supplied even if the +48V button of an
OMNI jack input channel or TALKBACK IN is on.
SETUP screen
STEP
1. In the Function Access Area, press the SETUP button.
2. In the field located in the right of the bottom row of the SETUP screen, press the
BANK A or BANK B button.
3. Use the multifunction knob to adjust the brightness of each item.
1 2 3 4 5 6 7
Setup
V5 Reference Manual
254
5 SCREEN
This knob adjusts the brightness of the touch screen.
If you have set the brightness to lower than level 2, the CL will start up next time with
a brightness setting of 2 so that you will be able to see the screen.
6 PANEL
Adjusts the brightness of the top panel LEDs. If the optional MBCL meter bridge is
installed on the CL3/CL1, this knob setting will also affect the LEDs on the meter bridge.
NOTE
If the AD8HR is connected, the brightness of the AD8HRs LEDs will also change.
7 LAMP
This knob adjusts the brightness of the lamps connected to the rear panel LAMP jacks.
Setting the date and time of the internal clock
This section explains how to set the date and time of the CL console’s internal clock, and how
to select the date and time display format. The date and time you specify here will affect the
time stamp used when saving a scene.
DATE/TIME window
Press the DATE/TIME button in the SETUP screen to open this window.
1 DATE
This field specifies the date of the internal clock.
2 TIME
This field specifies the time of the internal clock.
3 FORMAT (Display format)
Specifies the format in which the date and time of the internal clock are displayed.
You can select from the following display formats.
•Date
MM/DD/YYYY (Month/Day/Year)
DD/MM/YYYY (Day/Month/Year)
YYYY/MM/DD (Year/Month/Day)
•Time
24-Hour (hours shown in the range of 0-23)
12-Hour (hours shown from 0am-11am, and 0pm-11pm)
Setting the network address
This section explains how to set the network address that will be required when you use the
NETWORK connector on the CL series console to connect it to a computer.
If you plan to connect the CL series console to your computer in a one-to-one connection, we
recommend that you use the following default values.
IP Address: 192.168.0.128
Gateway address: 192.168.0.1
Subnet mask: 255.255.255.0
Make sure that the IP address and Gateway address do not match the addresses of any other
device on the network.
NOTE
Only the Administrator can change network settings.
For details on settings related to connecting to a LAN, refer to the CL Editor Installation Guide.
STEP
1. In the Function Access Area, press the SETUP button.
2. Press the DATE/TIME button at the lower part of the SETUP screen.
3. In the FORMAT field of the DATE/TIME window, press the MODE buttons several
times to select the desired format for date and time display.
4. Use multifunction knobs 1-6 in the Centralogic section to specify the current date
and time.
5. When you have finished making settings, press the OK button.
1 2 3
STEP
1. In the Function Access Area, press the SETUP button.
2. Press the NETWORK button at the lower part of the SETUP screen.
3. Press a knob in the NETWORK screen to select it, and use the multifunction knobs in
the Centralogic section to specify the address.
4. When you have finished making settings, press the OK button.
5. Restart the CL series console.
Setup
V5 Reference Manual
255
NETWORK window (FOR MIXER CONTROL page)
Use this window to set the consoles IP address, in order to use the NETWORK connector on
the rear panel to remote-control the console from CL Editor, StageMix, or the MonitorMix
application.
Set the UNIT Name and PIN for the MonitorMix application here.
For the IP SETTING MODE select buttons, only STATIC IP button is enabled. The other
buttons cannot be selected.
1 MAC ADDRESS
Indicates the MAC (Machine Access Control) address, which identifies a host in a
network. This address is for display only, and cannot be edited.
2 UNIT NAME
Sets the name to be shown on the network.
3 PIN for MonitorMix
Sets the PIN (4-digit numeric password) to be entered when using the MonitorMix
application to connect to a CL series console. MonitorMix is an iOS application that
musicians can use on stage to adjust their own monitor balance.
You can register a PIN with all 4 digits blank. In that case, PIN authentication with
MonitorMix is not required. However, you cannot leave only 1, 2, or 3 of the PIN digits
blank.
NOTE
The NETWORK connector on the CL series console transmits data via either 100BASE-TX
(transmission speed: maximum 100 Mbps) or 10BASE-T (transmission speed: max 10 Mbps).
NETWORK window (FOR DEVICE CONTROL page)
Use this window to set the console’s IP address, in order to use the Dante PRIMARY
connector on the rear panel to remote-control external devices. DHCP, AUTO IP, and fixed IP
settings are supported.
Even on DHCP networks, it is possible to remotely control external devices such as Tio1608-
D and Shures ULDX4.
1 CURRENT IP SETTING field
This field shows the current setting.
NOTE
If you use the IP SETTING MODE select buttons to select DHCP or AUTO IP, it may take some
time for the IP address to be configured. During this time, the window will appear as shown below.
3
1
2
6
1
7
2
3 4
5
Setup
V5 Reference Manual
256
NEXT IP SETTING field
2
IP SETTING MODE select buttons
Use these buttons to select how to set the IP address the next time the console is turned
on. Select DHCP, AUTO IP, or STATIC IP.
NOTE
If you select AUTO IP, the Dante network automatically sets the consoles IP address to
169.254.xxx.xxx.
If you select DHCP or AUTO IP, the window will appear as shown below and you will be
unable to set the IP ADDRESS, SUBNET MASK, and GATEWAY ADDRESS.
3 IP ADDRESS
Specifies an address that identifies an individual device on the Internet or LAN network.
4 SUBNET MASK
Within the IP address used in the network, this defines the bits that are used for the
network address that distinguishes the network.
5 GATEWAY ADDRESS
Specifies an address that identifies a device (gateway) that converts data between
different media or protocols to allow communication within the network.
6 APPLY button
Press this button after you have changed the IP address settings. When the ATTENTION
window appears, press the OK button and then turn the console off and back on again.
7 Tabs
Use these tabs to select a group of items to view (FOR MIXER CONTROL or FOR DEVICE
CONTROL).
Dante audio network settings
You will use the CL series console to make Dante audio network settings for the console itself
and the I/O devices connected to the Dante connector of the CL series console. This section
explains how to make Dante audio network settings.
STEP
1. In the Function Access Area, press the SETUP button to access the SETUP screen.
2. In the DANTE field at the center of the screen, press the DANTE SETUP button to
open the DANTE SETUP window.
3. Press the SETUP tab in the lower part of the DANTE SETUP window.
SETUP screen DANTE SETUP window
Setup
V5 Reference Manual
257
DANTE SETUP window (SETUP page)
1 STATUS indicators
Show the operating status of the CL series console and the Dante network.
2 CONSOLE ID select buttons
Set the IDs for the CL series consoles.
If five or more CL units are connected to a network, and you plan not to assign IDs to
some of the units, press the OFF button of each of those units to turn off the ID.
When the CONSOLE ID select button is set to OFF in the DANTE SETUP screen, the NOT
CTRL indicator appears below the Display switch button of each device.
The NOT CTRL indicator also appears on the icons of the DANTE PATCH screen.
3 SECONDARY PORT select buttons
Specify how the Dante audio network is configured.
4 CANCEL button
When editing the CONSOLE ID or SECONDARY PORT settings, you can press this button
to cancel the changes you made.
5 APPLY button
After changing the CONSOLE ID or SECONDARY PORT settings, press this button to
apply the changes you made.
6 BIT select buttons
Enable you to set the audio bit depth to 24-bit or 32-bit.
24bit................... Use this when transmitting and receiving data to or from an R series
unit. When using a CL series system, you will normally use this
setting.
4
1
23
9
8
5
6
7
Setup
V5 Reference Manual
258
32bit................... This is effective when transmitting and receiving 25-bit or larger data
(when using cascade or gain compensation), but the amount of data
being transmitted will increase 20-30% compared to 24-bit.
7 LATENCY select buttons
Enable you to set the Dante audio network latency to 0.25 ms, 0.5 ms, 1.0 ms, 2.0 ms,
or 5.0 ms.
The latency setting varies depending on the network connection method and size. For
details, refer to “Setting the Dante audio network latency” (page 261).
8 DANTE PATCH BY select buttons
If the THIS CONSOLE button is selected, the DANTE INPUT PATCH and DANTE OUTPUT
PATCH settings can be edited from the CL series console.
If the DANTE CONTROLLER button is selected, it will not be possible to edit the Dante
patch settings. You can operate these buttons regardless of the state of the DANTE
PATCH BY select buttons on other CL/QL series consoles on the network.
9 PREFERRED MASTER button
If this button is turned ON, the console’s status as a master is given greater priority in
the Dante audio network.
If this button is turned OFF, the console’s status as a master is given less priority in the
Dante audio network.
If there is only one CL console for which this button is turned ON, that console will become the
master.
If there are multiple CL consoles for which this button is turned ON, only one of them will become
the master.
If this button is turned OFF for all CL consoles, one unit out of all Dante devices, including I/O
devices, will become the master.
NOTE
Settings that are shared with the I/O device (BIT/LATENCY/W.CLOCK) will reflect the settings of
the CL series console whose CONSOLE ID is set to #1.
If the DANTE CONTROLLER button is selected in the DANTE PATCH BY section, and you
attempt to edit the Dante patching or related settings, the message “This Operation is Not
Allowed” will appear at the bottom of the screen.
DANTE patch information is applied to the device if the CL settings file (file name extension .CLF)
is loaded under the following conditions. Otherwise, the information is not applied and the current
state will be maintained.
In the SAVE/LOAD window (page 239), the WITH DANTE SETUP AND I/O DEVICE button is
on.
Either #1, #2, #3, or #4 CONSOLE ID select button is on.
The THIS CONSOLE button of the DANTE PATCH BY select buttons is on.
With CL V2.03 and later, when settings are initialized, including Dante audio network settings, or
a firmware update is installed, the Preferred Master setting is turned on. This setting is not
changed when console settings are changed or when the console is restarted. It can be turned
off using the Dante Controller, if necessary. If this default setting is used to change CL or QL word
clock settings for anything other than Dante, that console is given priority as the clock master for
the Dante network to prevent clock synchronization errors. Further, you can use Dante Controller
to clearly specify the master by turning on only Preferred Master for the device that will always be
running (off for all other devices).
Dante Device Lock
Dante Device Lock prevents changes to the Dante audio network settings of a Dante device
by another computer on the same network. Dante Device Lock settings are configured in
Dante Controller.
When Dante Device Lock is enabled on a CL console, the following parameters cannot be
changed.
CONSOLE ID
SECONDARY PORT
•BIT
LATENCY (ms)
PREFERRED MASTER
When Dante Device Lock is enabled on a CL console, the DANTE DEVICE LOCKED indicator
lights up in red on the top left side of the DANTE SETUP window.
If you try to change any of these parameters, the following message will appear at the bottom
of the window.
Setup
V5 Reference Manual
259
If a device connected to the console is online, and Dante Device Lock is enabled for that
device, the LOCKED indicator will appear in each window as shown below.
If Dante Device Lock is enabled for the console, the following specifications will apply.
The master clock select buttons in the WORD CLOCK/SLOT window cannot be changed.
None of the parameters in the DANTE INPUT PATCH window can be changed. RECALL
and AUTO SETUP in the DANTE INPUT PATCH LIBRARY window will be disabled.
None of the parameters in the I/O DEVICE [OUTPUT PATCH] window can be changed.
If a file is being loaded from USB memory to a device that has Dante Device Lock enabled,
the settings will not be changed by the loaded file. A message is displayed on the screen.
If the consoles internal memory is initialized to the factory settings, Dante Device Lock will
remain enabled and cannot be changed. Locked parameters will also not be initialized.
If the consoles Dante settings are initialized to the factory settings, Dante Device Lock will
be disabled. Locked parameters will also be initialized. R
efer to “Initializing the console settings
and Dante audio network settings” (page 282).
USB memory cannot be used to update the Dante module firmware. In addition, Dante
Firmware Update Manager will not update the firmware.
NOTE
If Dante Device Lock is enabled for a remote device, all offline settings (such as Dante Patch) for
the device will be disabled.
Even if Dante Device Lock is enabled for an I/O device, remote control that is unrelated to Dante
settings (such as HA control for R series) is possible.
Support for Dante Domain Manager
When a DDM server exists in the network, or when enrolling a domain, the DANTE DOMAIN
MANAGER field is shown at the top of the DANTE SETUP screen.
1 STATE
Displays the status of domain participation.
Domain: Domain is enrolled
Disconnected: Domain is enrolled without connecting to the DDM server
Unmanaged: Domain is not enrolled
2 LOCAL
Displays the access status of the Dante settings (including the DANTE PATCH settings)
on the current operating unit.
Read Write: Editing is available
Read Only: Editing is disabled
1 2 3
Setup
V5 Reference Manual
260
3 REMOTE
Displays the access status of the Dante settings of the external Dante devices.
Operator: Editing is available
Guest: Reading is available, editing is disabled
None: Reading and editing are disabled
The display changes depending on the REMOTE settings.
I/O DEVICE screen
DANTE PATCH screen, DANTE SETUP DEVICE MOUNT screen
Switching the CONSOLE ID and SECONDARY PORT
DANTE SETUP window (SETUP page)
The button you switched is shown in red.
When the Dante audio network settings have been applied, the button you selected will return
to its original appearance.
NOTE
If you change the SECONDARY PORT, you must also change the method of connection between
the CL series console and the I/O devices. For example if the connections used for the
REDUNDANT setting are left as they are when you change the setting to DAISY CHAIN, it will
become impossible to send and receive audio. Be sure to disconnect the cables before you
change the setting.
The CONSOLE ID and SECONDARY PORT settings will not be changed even if you initialize the
CL series console.
When the CONSOLE ID is OFF or is set to 2, 3, or 4 for a CL series console, the console’s BIT/
LATENCY will not change even if the BIT/LATENCY is changed in the DANTE SETUP window
for the CL series console within a network for which the CONSOLE ID is set to 1.
STEP
1. In the DANTE SETUP window (SETUP page), select the CONSOLE ID and the
SECONDARY PORT.
2. Press the APPLY button.
3. In the window to confirm the change, press the OK button.
Setup
V5 Reference Manual
261
When the CONSOLE ID is set to OFF, the DANTE PATCH BY field is fixed to “DANTE
CONTROLLER.” Also, patching cannot be changed in the DANTE INPUT PATCH window.
When the CONSOLE ID is set to OFF, all the mounted devices will be “virtual.
You can edit HA GAIN and other settings for R series units, but notification of the settings will not
be sent to the device. This is the same as when the devices are not connected.
Setting the Dante audio network latency
An appropriate latency setting for signals transmitted over a Dante audio network varies
depending on the network connection method and size. This section explains how to set an
appropriate latency setting depending on the connection method of Dante-enabled devices
that are connected to the CL series console.
Relationship between the switches and the number of hops
An appropriate latency setting on a Dante audio network varies depending on the number of
hops in the network. One hop is the step from one router (switch) to the next. You count the
number of hops starting from the master device to the most distant device (assuming that all
devices are connected in series).
Switches mean switching hubs as well as the switches that are built into CL series consoles
and I/O devices. Set the latency value based on the number of hops. The following table
shows typical latency settings based on the number of hops.
NOTE
Depending on network conditions, you may want to raise the latency value even if the number of
hops is small.
If a problem occurs, select 5.0 ms so that you will be able to identify whether the latency setting
is the cause of the problem.
When a DDM server is connected, the latency can be set to 10.0ms, 20.0ms, or 40.0ms. Use
Dante Controller to set it. The CL console does not support these settings.
Connection examples and latency settings
Daisy chain connections
Simple 64-in/48-out
Daisy chain connections
FOH and monitor consoles are sharing 64-in/48-out.
Number of hops Latency (ms)
Up to 3 0.25
Up to 5 0.5
Up to 10 1.0
Up to 20 2.0
21 or more (or if a problem occurs) 5.0
3
3
2
2
11
3 hops = 0.25 ms 3 hops = 0.25 ms
4
2
11
3
3
2
4 hops = 0.5 ms 3 hops = 0.25 ms
Setup
V5 Reference Manual
262
Redundant connections
Simple 64-in/48-out
Redundant connections
FOH and monitor consoles are sharing 64-in/48-out.
Daisy chain connections
256-ch HA remote (maximum size)
3
4
12
4 hops = 0.5 ms
3
4
12
4 hops = 0.5 ms
9
8
7
6
5
4
3
2
2
3
4
11
9 hops = 1.0 ms 4 hops = 0.5 ms
Setup
V5 Reference Manual
263
Redundant connections
Two CL series consoles are sharing 256-ch HA remote (maximum size)
Mounting an I/O device on the Dante audio network
Heres how to select which of the multiple I/O devices on the Dante audio network will be
mounted so that they can be used. Up to 24 units can be mounted for one CL series console.
With V4.1 or later, the Shure AXT400, QLXD4, and ULXD4 wireless systems, which do not
feature Dante output, can now be controlled. These Shure devices can be connected to the
same physical network as Dante, mounted, and controlled.
However, the actual audio signals are physically connected to an R series I/O rack mounted
on the CL console or to OMNI IN. By associating the port where audio is input with the
mounted Shure device, control and monitoring are possible from the input channel that is
patched to the input port. For details about the explanation of how to control the Shure
wireless systems, which do not feature Dante output, refer to
C on P. 1 8 5 , PORT ASSIGN
tab.
4
5
3
2
1
5 hops = 0.5 ms
STEP
1. Press the DEVICE MOUNT tab in the lower part of the DANTE SETUP window.
2. Press the I/O device select button.
3. In the DEVICE SELECT window, press the setup method select button.
4. Use the corresponding multifunction knob to make settings.
5. When you have finished making settings, press the OK button to close the window.
Setup
V5 Reference Manual
264
DANTE SETUP window (DEVICE MOUNT page)
NOTE
CL console can recognize up to 24 Shure AXT400, QLXD4, and ULXD4 devices on the same
Dante audio network, including Shure ULXD4D and ULXD4Q Dante output devices that are set
to YAMAHA ID mode. Note that if a greater number of devices is connected, some of the devices
will not be recognized by the console based on the order in which their power is turned on, etc,
regardless of the mount setting.
1 CLEAR ALL button
Clears all I/O devices in the list to an unmounted state.
2 REFRESH button
Updates the displayed list of I/O devices on the Dante audio network.
3 I/O device select buttons
Press one of the buttons to open the DEVICE SELECT window. The upper line of the
button shows the device label. The lower line of the button shows the model name and
the number of inputs and outputs. If no device has been mounted, the upper row will
indicate “---” and the lower row will show nothing.
For more information on VIRTUAL/CONFLICT/DUPLICATE shown below these buttons,
refer to
1 on P.173, “I/O device list.”
DANTE SETUP window
1 Setup method select buttons
Choose one of the following methods for mounting the I/O device.
NO ASSIGN........................ Not mounted
DEVICE LIST...................... Select and mount from the device list
SUPPORTED DEVICE ....... Select and mount a supported device
DVS ..................................... Enter a device label and mount (only for DVS)
MANUAL............................. Enter a device label and mount
1 2
3
1
Setup
V5 Reference Manual
265
When the setup method select button is DEVICE LIST
To mount by choosing from a list of the I/O devices on the Dante audio network, press the
DEVICE LIST button to display the DEVICE LIST field.
1 DEVICE LIST
Shows a list of the I/O devices on the Dante audio network.
From the list, choose the I/O device that you want to mount.
2 DEVICE LIST select knob
Use the corresponding multifunction knob to select the I/O device that you want to
mount.
3 DEVICE IDENTIFY button
If a device has the DEVICE IDENTIFY function, the DEVICE IDENTIFY button is enabled.
Otherwise, this button will be grayed out and cannot be pressed.
When the setup method select button is SUPPORTED DEVICE
If you want to select and mount an I/O device that is supported by the CL series, press the
SUPPORTED DEVICE button to see the SUPPORTED DEVICE field. These settings can be
made even when not connected to a Dante audio network.
1 DEVICE TYPE
This area shows a list of the I/O device types that are supported by the CL series.
From the list, choose the type of I/O device that you want to mount.
2 DEVICE TYPE select knob
Use the corresponding multifunction knob to select the type of I/O device that you want
to mount.
3 I/O device indication
This area shows the selected I/O device.
The upper line shows the front panel of the I/O device.
The lower line shows the model name and the number of inputs and outputs. The
REMOTE icon appears in the remote control supported device.
For devices that do not future Dante output, “NO DANTE PORT” appears on the right
side.
NOTE
If a device does not feature Dante output, offline mounting is not possible. Mount it when online
(make sure the DEVICE LIST button is on).
1
2
3
1
2
3
4
Setup
V5 Reference Manual
266
4 UNIT ID knob
Use the corresponding multifunction knobs to specify the UNIT ID.
The indicator shows the UNIT ID.
NOTE
If there is one I/O device, set the I/O device’s UNIT ID to “1.
If multiple devices are connected, assign the ID numbers so that there is no conflict between
devices.
For devices other than the R series, it is possible for devices of differing models to be assigned
to the same ID as an R series unit or the same ID as a different model of device. However, since
the I/O device input/output port screen shows the UNIT ID, this will make it difficult to distinguish
between the units, so we recommend that whenever possible, you avoid allowing the ID numbers
to overlap.
If you have a device whose UNIT ID or device label cannot be changed from its panel or its edit
screen etc. (such as the Dante-MY16-AUD card or Dante Accelerator), and you want to use that
device as a SUPPORTED DEVICE, you must change its device label via Dante Controller.
An I/O device will be recognized as a SUPPORTED DEVICE if you assign the device label as
follows.
Y###-**********
# is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A to F (000 -
FFF)
* indicates any desired character (alphabetical uppercase or lowercase, numerals, or - (hyphen)
may be used)
If you are controlling the CL series console from an R series unit, we recommend that you set the
R unit’s START UP MODE to “REFRESH. Operation will be safer with the “REFRESH” setting,
since mute will be cleared after synchronization has been completed with CL units whose system
setting for REMOTE HA ASSIGN is set to “WITH RECALL.
With the “RESUME” setting, mute will be cleared and the unit will start operating with the settings
that were backed up by the R series unit itself, which could allow unexpected audio to be output.
A single CL series console can control the HA of up to eight R series units.
If nine or more R series units are connected, you can either divide the HA control between
multiple CL series consoles, or you can omit specifying REMOTE HA ASSIGN for the R series
units whose HA does not need to be controlled, and use them with START UP MODE set to
“RESUME.
When the setup method select button is DVS or MANUAL
If you want to enter the device label of an I/O device and mount it, press the DVS or MANUAL
button to access the DVS/MANUAL field.
1 DEVICE LABEL
Displays the device label of the I/O device which you entered from the keyboard.
2 INPUT/OUTPUT knobs
Use the corresponding multifunction knobs to specify the number of inputs and outputs
on the Dante audio network.
3 Device label entry keyboard
Use this keyboard to enter the device label of the I/O device.
NOTE
If the I/O device is a DVS, mount it by pressing the DVS button.
If DEVICE LABEL is left blank, the first DVS detected is automatically mounted.
If the device label you entered is detected automatically, the INPUT/OUTPUT knob settings will
be ignored, and the rated number of inputs and outputs will be specified.
1
3
2
Setup
V5 Reference Manual
267
REMOTE HA settings
Heres how to select which of the multiple HA devices on the Dante audio network will be
mounted so that they can be used. Up to 8 units can be mounted for one CL series console.
A device with many channels occupies two racks. For such device, you can only mount on
odd numbered racks. Also, it is necessary to have two racks in a row. Up to four units can be
mounted.
DANTE SETUP window (REMOTE HA page)
1 CLEAR ALL button
Clears all HA devices in the list to an unmounted state.
2 REFRESH button
Updates the displayed list of HA devices on the Dante audio network.
3 HA device select buttons
Press one of these buttons to open the REMOTE HA SELECT window. The upper line of
the button shows the device label. The lower line of the button shows the model name
and the number of inputs and outputs. If no device has been mounted, the upper row
will indicate “---” and the lower row will show nothing.
For more information on VIRTUAL/CONFLICT/DUPLICATE shown below these buttons,
refer to
1 on P.173, “I/O device list.”
REMOTE HA SELECT window
1 DEVICE LIST
Shows a list of the HA devices on the Dante audio network.
2 WITH RECALL button
If this button is on, the settings saved in the CL series console will be applied to the HA
device when the CL series console starts up and when a scene is recalled.
3 DEVICE LIST select knob
Use the corresponding multifunction knob to select the HA device that you want to
mount.
NOTE
Do not specify “WITH RECALL” if an HA device is shared by multiple CL series consoles and
settings have already been made on a different CL series console.
The HA device can also be operated from a CL series console that is not set to “WITH RECALL.
STEP
1. Press the REMOTE HA ASSIGN tab in the lower part of the DANTE SETUP window.
2. Press a HA device select button to access the REMOTE HA SELECT window.
3. Select the HA device to mount and press the OK button.
If you have changed the setting by pressing the WITH RECALL button, a
confirmation dialog box will appear. Press the OK button.
13 2
1
3
2
Setup
V5 Reference Manual
268
Displaying the device status
You can use the touch screen to verify the status of a connected CL series or R-series unit
(except the Ro8-D) or the Dante status. In order to verify the status of an R-series unit from
the console, it must be assigned to REMOTE HA in DANTE SETUP.
CL series
The SETUP field of the DANTE SETUP window shows indicators for the status of the CL
series console and the Dante network.
R-series
The I/O field of the I/O DEVICE screen shows indicators for the status of the R-series units
and the Dante network.
For firmware that predates support for V1.60, the version indication will be yellow and the
indicator will be unlit.
Messages
Error, warning, and information messages are displayed.
Messages are also displayed in the Dante Controller Error Status field.
Each indicator lights or flashes as described below:
No call-out Unlit
Lit The indicator remains lit steadily.
Blinking The indicator continues to flash.
Flash x2 The indicator flashes twice cyclically.
Flash x3 The indicator flashes three times cyclically.
Setup
V5 Reference Manual
269
Error messages
The SYSTEM indicators will remain lit/blinking cyclically as follows until the problem has been
resolved.
If service is necessary, please contact the Yamaha service center listed in the CL5/CL3/CL1
Owner’s Manual.
Warning messages
The indicators will remain lit/blinking cyclically until the problem has been resolved.
If the green [SYNC] indicator is not lit, the device’s word clock is not defined.
[SYSTEM] indicators Meaning Possible solution
An internal error has occurred.
The device has failed. Contact
your Yamaha dealer for repair.
The MAC address setting has
been corrupted and no
communication can occur via
Dante.
The internal memory has
been corrupted.
If the problem persists after
setting START UP MODE back to
RESUME and turning the power
on again, consult your Yamaha
dealer.
UNIT ID is not unique.
Set a unique UNIT ID number for
the Dante network.
The DIP switches are not set
correctly.
Check the DIP switch settings,
and set them correctly.
Dante flow number limit was
exceeded.
Examine the Dante network
routing.
Flash x2
Flash x3
Flash x3
Lit
Lit
Blinking
Blinking
Lit
The positions of the device
setting DIP switches do not
match the actual Dante settings.
If the Device Lock setting was
enabled from Dante Controller or
if the device is set to READ ONLY
in DDM mode, disable the setting.
Check the device setting DIP
switch positions, and set them to
accommodate the current
situation.
Power supply problem has
occurred on Rio3224-D2/
Rio1608-D2.
Check whether power is supplied
correctly to the AC IN connectors
A and B respectively.
[SYNC] indicators Meaning Possible solution
The word clock is not set
correctly.
Set the word clock master and the
sampling frequency correctly on
the CL5/CL3/CL1-native device or
in Dante Controller.
Dante Network circuit is
broken.
Make sure that the Ethernet
cables are not removed or short-
circuited.
Dante Network is connected
incorrectly. Other Dante
devices cannot be found.
Make sure that the Ethernet
cables are connected correctly.
[SYSTEM] indicators Meaning Possible solution
Lit
Lit
Blinking
Flash x2
Flash x3
Setup
V5 Reference Manual
270
If the green indicator is blinking, the unit is operating as the word clock master.
If the green indicator lights, the unit is operating as a word clock slave and synching to the
word clock.
Information messages
The indicators will remain lit /blinking cyclically to report the status.
If the orange [SYNC] indicator is not lit, the unit is operating correctly.
If the green [SYNC] indicator is not lit, the device’s word clock is not defined.
[SYNC] indicators Meaning Possible solution
A non-GbE-compatible device
is connected.
If audio is transmitted over the
Dante network, use a GbE-
compatible device.
The SECONDARY connector
has taken over
communications during
redundant network operation.
Check the circuit connected to the
PRIMARY connector.
An abnormality has occurred
on the circuit connected to the
SECONDARY connector
during redundant network
operation.
Check the circuit connected to the
SECONDARY connector.
Lit
Lit or
blinking
Blinking
Lit or
blinking
Flash x2
Lit or
blinking
[SYNC] indicators Meaning Possible solution
Syncing the Dante network
Please wait until started has
completed or until the unit has
finished synchronization. It may
take up to 45 seconds for
completion.
Waiting to receive setting data
Use REMOTE HA ASSIGN in the
system to sync with a console or
R Remote set to “WITH RECALL.
For an R series console with the
START UP MODE set to
REFRESH, after startup both
input and output are muted until
the setting data is received.
For a single R series console, do
not set “WITH RECALL” from
multiple consoles.
The device is operating
correctly as a word clock
master.
This indicates that the device is
operating as a word clock master.
The device is operating
correctly as a word clock
slave.
This indicates that the device is
operating as a word clock slave
and synching to the word clock.
Lit
Blinking
Lit
Setup
V5 Reference Manual
271
Using GPI (General Purpose Interface)
The rear panel GPI (General Purpose Interface) connector can be used as an input/output
connector. This connector provides five GPI IN ports and five GPI OUT ports. For example
you can use an external switch to control internal parameters of the CL series console or to
switch scenes. Conversely, operations or scene changes performed on the CL series console
can send control signals to an external device.
For details on how to send control signals to an external device when you switch scenes, refer
to “Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
(page 109).
Using GPI IN
You can use the GPI IN ports of the GPI connector to control the parameters of the CL series
console from an external device. For example, you could use an external switch to turn the CL
series consoles Talkback on/off, operate the Tap Tempo function, or switch scenes.
NOTE
With latched operation, the function will switch between active and inactive each time a trigger is
input from the external switch. In this case, we recommend that you use a non-locking type of
external switch.
With unlatched operation, the function will be active only while the signal from the external switch
is at the high level or low level. In this case, you may use either a non-locking or a locking type
of external switch as appropriate for your needs.
Settings in the GPI page of the MIDI/GPI screen are common to all scenes. They can be saved
as SETUP data.
MIDI/GPI screen (GPI page)
1 GPI IN status indicator
This indicates the status of the voltage being input to the GPI IN port.
2 POLARITY MODE select button
This button selects the polarity of the GPI IN port.
............... (Low active) When operating an on/off-type parameter, it will
become active when the switch is grounded.
............... (High active) When operating an on/off-type parameter, it will
become active when the switch is opened or when a high-level
voltage is input.
STEP
1. Connect an external device to the CL series console’s GPI connector.
2. In the Function Access Area, press the SETUP button.
3. In the SETUP screen, press the MIDI/GPI button.
4. In the MIDI/GPI screen, press the GPI tab.
5. Specify the POLARITY MODE for each port as appropriate for the specifications of
the external device you’re using.
6. To assign the function or parameter that you want to control, press the GPI IN
SETUP button.
7. In each field of the GPI IN SETUP window, select the desired function and parameter,
then press the OK button.
SETUP screen MIDI/GPI screen
4
1
2
3
Setup
V5 Reference Manual
272
3 GPI IN SETUP button
The button shows the name of the currently-selected function or parameter. Press this
button to display the GPI IN SETUP window.
NOTE
The items that can be selected in the GPI IN SETUP window are the same as for the USER
DEFINED keys (page 224).
4 Switch attribute select button
This button selects the switch attribute. Each time you press the button, its indication
will alternate between LATCH and UNLATCH.
................. LATCH (a switch that alternately turns on/off each time it is pressed)
is selected.
................. UNLATCH (a switch that is on only while pressed and is off when
released) is selected.
Using GPI OUT
The GPI OUT ports of the GPI OUT connector allow you to control an external device by
performing operations on the CL series console.
STEP
1. Connect an external device to the CL series console’s GPI connector.
2. In the Function Access Area, press the SETUP button.
3. In the SETUP screen, press the MIDI/GPI button.
4. In the MIDI/GPI screen, press the GPI tab.
5. Specify the POLARITY MODE for each port as appropriate for the specifications of
the external device you’re using.
6. To assign a function or parameter that you want to control, press the GPI OUT
SETUP button.
7. In each field of the GPI OUT SETUP window, select the desired function and
parameter, then press the OK button.
SETUP screen MIDI/GPI screen
Setup
V5 Reference Manual
273
MIDI/GPI screen (GPI page)
1 GPI OUT status indicator
This indicates the status of the voltage that is being output from each GPI OUT port.
2 POLARITY MODE select button
This button selects the polarity of the GPI OUT port.
............... (Low active) Grounded when the GPI OUT port is active.
............... (High active) Open when the GPI OUT port is active.
3 GPI OUT SETUP button
The button shows the name of the currently-selected function or parameter. Press this
button to display the GPI OUT SETUP window.
You can assign the following functions.
4 TEST button
While this is on, the corresponding GPI OUT port will be active and will output a control
signal.
234
1
Function PARAMETER 1 PARAMETER 2 Description
NO ASSIGN - - No assignment
CUE ACTIVE CUE ON - Turn on the [CUE] key of the
selected channel
DCA ONLY - Turn on the DCA [CUE] key
INPUT ONLY - Turn on the [CUE] key of an input
channel
OUTPUT ONLY - Turn on the [CUE] key of an output
channel
DANTE REDUNDANCY
IND.
PRIMARY This function activates when the
unit is operating on the primary
Dante audio network with a star
connection (redundant network).
SECONDARY This function activates when the
unit is operating on the secondary
Dante audio network with a star
connection (redundant network).
GPI IN ACTIVE
IND.
SPECIFIC PORT PORT 1 to PORT 5 The function assigned to GPI IN
port 1 - 5 becomes active
POWER ON - - The power of the CL series
console is turned on
USER DEF.
KEY ACTIVE
IND.
SPECIFIC
NUMBER
USER DEFINED
KEY 1 to USER
DEFINED KEY 16
The function assigned to the
USER DEFINED key becomes
active
Setup
V5 Reference Manual
274
Using FADER START
Make FADER START settings if you want a device connected to a GPI OUT port to operate
in tandem with fader operations.
MIDI/GPI screen (FADER START page)
1 CLEAR ALL button
Clears all selections.
OUTPUT DESTINATION field
2
GPI OUT1 to GPI OUT5 buttons
Select the GPI OUT port for which you want to make settings.
3 Fader indicator
This indicates the selected fader. Use the [SEL] keys on the panel to select a fader.
NOTE
In the case of the CL3/CL1, channels that do not exist on those models will not be shown.
STEP
1. Connect an external device to the CL series console’s GPI connector.
2. In the Function Access Area, press the SETUP button.
3. In the SETUP screen, press the MIDI/GPI button.
4. In the MIDI/GPI screen, press the FADER START tab.
5. For each GPI OUT port, specify the channel that will cause the external device to
operate, and the type of operation.
SETUP screen MIDI/GPI screen
3
2
8 5 6 7
4
1
Setup
V5 Reference Manual
275
THRESHOLD field
4
UPSTROKE/DOWNSTROKE
These specify the level that will be the threshold for outputting a trigger signal. A trigger
signal will be output when the fader exceeds the UPSTROKE level, or when the fader falls
below the DOWNSTROKE level. You can use the multifunction knobs to operate this.
NOTE
The THRESHOLD values specified by the UPSTROKE/DOWNSTROKE knobs are common to all
channels (faders) and all GPI OUT ports. However, you can individually choose the channel (fader)
for each GPI OUT port.
Only the UPSTROKE value will be valid if MODE is set to FADER START, and only the
DOWNSTROKE value will be valid if MODE is set to FADER STOP. If MODE is set to FADER
TALLY, both the UPSTROKE and DOWNSTROKE values will be valid.
MODE field
Here you can select the mode of fader operation that will be the trigger for signal output from
the GPI OUT port.
You can choose from the following fader modes.
5 FADER START
A trigger signal 250 msec long will be output when the fader of the selected channel
moves upward through the specified UPSTROKE level (-∞ to+10.0 dB) from a point
below it.
6 FADER STOP
A trigger signal 250 msec long will be output when the fader of the selected channel
reaches the specified DOWNSTROKE level (-∞ to +10.0 dB).
7 FADER TALLY
A trigger signal will be output when the fader of the selected channel moves upward
through the specified UPSTROKE level (-∞ to +10.0 dB) from a point below it. This signal
will be held until the fader reaches the specified DOWNSTROKE level (-∞ to +10.0 dB)
or until that GPI OUT port receives a different trigger. This signal will be held until the
fader reaches the specified DOWNSTROKE level (-∞ to +10.0 dB) or until that GPI OUT
port receives a different trigger.
8 NO ASSIGN
Operating the fader of the selected channel will not cause a signal to be output.
The following illustration shows how the signal that is output from the GPI PORT will change
in each fader mode when a fader is operated. In this example, UPSTROKE in the
THRESHOLD eld is set to -60.00, and DOWNSTROKE is set to -∞. (This illustration shows
the case in which is selected as the polarity of the GPI OUT port. If the polarity is ,
the polarity of the output signal will be reversed.)
NOTE
At the high level, the output signal of the port will be open. If the receiving device requires high
level, take it from the +5V power supply pin. However in this case, the amount of current is limited;
For details, refer to the control I/O specification in the CL data list (at the end of this manual).
FADER
START
FADER
TALLY
FADER
STOP
250 msec
250 msec
Help function
V5 Reference Manual
276
Help function
You can view Help files (file extension .xml) provided by Yamaha. For the latest information on
help files, refer to the Yamaha Pro Audio website.
https://www.yamaha.com/proaudio/
In addition, using a commercially available text editor or the “Notepad” included with Microsoft
Windows, you can create a text file (file extension .txt) and display it on the console*.
* We accept no responsibility for any damage that may occur as a result of using Help files
created by a third party other than Yamaha.
Loading a Help/text file from a USB flash drive
NOTE
A help file for only one language is stored in the console’s internal memory. Once you load the
help file, it will be preserved in internal memory even if the power is turned off. The first time you
press the HELP button to view the help file after turning the power on, it will take a while for the
help file to be loaded from internal memory. Once the data has finished loading, subsequently
pressing the HELP button will display the help file instantly.
NOTE
By default, the character code set of the text file will be detected as UTF-8. However, by adding
a line consisting of [ISO-8859-1] or [Shift_JIS] at the beginning of the file, you can force
recognition of the file using that character code set. You can specify the desired character code
set when using your text editor to save the text file.
The Help function is able to display the following text files (character code sets /languages).
Text files written in the ISO-8859-1 character code set (English, German, French, Spanish, etc.)
Text files written in the Shift_JIS character code set (Japanese)
Text files of the above languages written in the UTF-8 character code set
Viewing Help
Operation in the HELP window
You can use the multifunction knob or screen buttons to access the HELP window.
Turn multifunction knobs 1 and 2.
.............Scrolls the index area at the left.
Turn multifunction knobs 3 - 8.
.............Scrolls the main area at the right.
Pressing a link (underlined text) in the text
.............Scrolls to the linked destination.
Pressing a window link (a location with an
symbol and underlined text)
.............Closes the HELP window and opens the corresponding window.
Pressing the button ........ Scrolls to the chapter that precedes the currently-
displayed location.
Pressing the button ........ Returns to the preceding item in the history of links
you pressed.
Pressing the button ........ Advances to the next item in the history of links you
pressed.
STEP
1. Save the Help file provided by Yamaha or a user-created text file on your USB flash
drive.
2. In the Function Access Area, press the SETUP button.
3. In the SETUP screen, press the SAVE/LOAD button.
4. To select the Help/text file that you want to load, press one of the Help/text files in
the file list in the SAVE/LOAD window, or turn the multifunction knob in the
Centralogic section.
5. Press the LOAD button.
6. Press the OK button in the confirmation dialog box to load the file.
SAVE/LOAD window
STEP
1. Load the Help file or text file from your USB flash drive.
2. In the Function Access Area, press the (Help) button.
3. To close the HELP window, press the (Help) button of the Function Access
Area or the “x” symbol of the HELP window.
Help function
V5 Reference Manual
277
Using USER DEFINED keys to recall Help directly
Assigning the Help function to USER DEFINED keys
Recalling the HELP window using only a USER DEFINED key
Press the USER DEFINED key to which the Help function is assigned. The HELP window will
appear. To close the window, once again press the USER DEFINED key to which the Help
function is assigned.
Directly recalling the Help for a specific panel controller
While holding down the USER DEFINED key to which you have assigned the Help function,
press (or rotate) the panel controller for which you want to recall Help. If the explanation is
available for the controller, the help for the corresponding item will appear.
To close the window, once again press the USER DEFINED key to which the Help function is
assigned.
NOTE
Panel controllers (other than the faders and the MONITOR LEVEL knob) will not function as long
as you continue holding down the USER DEFINED key to which the Help function is assigned.
If there are multiple explanations for the same controller, you can repeat the steps above to
successively display these explanations.
Directly recalling the Help for a specific controller in the LCD screen
While holding down the USER DEFINED key to which you have assigned the Help function,
press the on-screen controller for which you want to recall Help. If the explanation is available
for the controller, the help for the corresponding item will appear.
To close the window, once again press the USER DEFINED key to which the Help function is
assigned.
NOTE
The on-screen controllers will not function as long as you continue holding down the USER
DEFINED key to which the Help function is assigned.
If there are multiple explanations for the same controller, you can repeat the steps above to
successively display these explanations.
STEP
1. Load the Help file from your USB flash drive.
2. In the Function Access Area, press the SETUP button.
3. Press the USER SETUP button in the upper left of the SETUP screen.
4. Press the USER DEFINED KEYS tab in the USER SETUP window.
5. In the USER DEFINED KEYS page, press the button corresponding to the USER
DEFINED key to which you want to assign the Help function.
6. In the FUNCTION column, choose “HELP” and press the OK button.
7. Press the “x” symbol to close the USER DEFINED KEYS page.
8. In the Function Access Area, press the SETUP button to close the SETUP screen.
SETUP screen USER SETUP window (USER
DEFINED KEYS page)
Other functions
V5 Reference Manual
278
Other functions
This chapter explains various functions of CL series consoles that are not covered in other
chapters.
Initializing the unit to factory default settings
If an error occurs in the CL console internal memory, or if you forget the password and cannot
operate the unit, you can use the following procedure to initialize the internal memory.
There are two types of initialization of the internal memory as shown below.
INITIALIZE ALL MEMORIES
The entire memory, including scene memories and libraries, will be returned to factory default
settings.
INITIALIZE CURRENT MEMORIES
The contents of memory - except for scene memories and libraries - will be returned to its
factory default settings.
CAUTION
The entire memory will be deleted if you initialize the internal memory! Proceed with the operation
only if you are very sure you want to delete the entire memory.
However, the settings in DANTE SETUP will not be initialized. To initialize these settings, refer to
Initializing the console settings and Dante audio network settings” (page 282).
NOTE
Do not press any buttons until initialization is complete.
Once initialization is complete, you can continue operation by selecting a different menu instead
of pressing the EXIT button.
Adjusting the detection point of the touch screen
(Calibration function)
Follow the steps below to correctly align the positions of the LCD display and the touch
screen.
NOTE
If you are unable to start calibration by pressing the TOUCH SCREEN CALIBRATION button, you
can use the SCENE MEMORY [INC]/[DEC] keys to select TOUCH SCREEN CALIBRATION, and
then press the [STORE] key to start.
To set the detection points accurately, press the cross-shaped cursor from the position and
posture in which you normally operate the unit.
Once initialization is complete, you can continue operation by selecting a different menu instead
of pressing the EXIT button.
STEP
1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the
power to the CL unit.
2. On the startup menu screen, select the initialization method.
3. Press the INITIALIZE button in the dialog box to confirm initialization.
4. Press the OK button in the confirmation dialog box to start initialization.
5. A message indicates that the initialization process is complete. Press the EXIT button
on the startup menu screen.
Startup menu screen
STEP
1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the
power to the CL unit.
2. On the startup menu screen, press the TOUCH SCREEN CALIBRATION button.
3. Press the START button in the TOUCH SCREEN CALIBRATION MODE screen.
4. Press the OK button in the confirmation dialog box to start calibration.
5. A cross-shaped cursor will appear in the screen (a total of three times). Press each
location at which it appears.
6. Press the EXIT button on the startup menu screen to start up the CL unit in normal
operating mode.
Startup menu screen TOUCH SCREEN CALIBRATION
MODE screen
Other functions
V5 Reference Manual
279
Adjusting the faders (Calibration function)
Depending on the environment in which you use the CL series console, discrepancies may
occur in the motion of the motor faders. You can use the Calibration function to correct these
discrepancies.
NOTE
The specified faders in the channel strip section, Centralogic section, and Master section will be
semi-automatically calibrated. This window will also appear if a problem is detected in the fader
settings while the CL is starting up.
NOTE
Faders for which a problem was detected at start-up will already be selected in step 3.
If the RESTART button appears, calibration has failed. Press the RESTART button to execute
calibration once again.
Once initialization is complete, you can continue operation by selecting a different menu instead
of pressing the EXIT button.
Fine-tuning the input and output gain (Calibration
function)
If necessary, you can make fine adjustments to the input and output gain.
NOTE
If you press the RESET ALL button provided in each screen, all settings in the screen will be reset
to 0 dB.
The factory settings are also 0 dB.
Once initialization is complete, you can continue operation by selecting a different menu instead
of pressing the EXIT button.
STEP
1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the
power to the CL unit.
2. On the startup menu screen, press the FADER CALIBRATION button.
3. Press a [SEL] key to select the faders that you want to calibrate.
4. Press the START button in the FADER CALIBRATION MODE screen.
5. Press the OK button in the confirmation dialog box.
6. Each of the specified faders will move to -∞ (all the way down). If the fader positions
are not correct, move them manually to -∞ (all the way down).
7. After you adjust the fader position, press the NEXT button.
8. Repeat steps 6 to 7 to adjust three fader positions at 20 dB, 0 dB, +10 dB (all the way
up).
When adjustment to the +10 dB position is complete, calibration starts.
9. When calibration has been completed, press the APPLY button.
10. Press the EXIT button on the startup menu screen to start up the CL unit in normal
operating mode.
Startup menu screen
STEP
1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the
power to the CL unit.
2. In the MODE SELECT field on the startup menu screen, press the button for the item
you want to adjust.
3. Press an on-screen knob to select it, and then use the corresponding multifunction
knob to adjust the value.
4. Press the EXIT button on the startup menu screen to start up the CL unit in normal
operating mode.
Startup menu screen
Other functions
V5 Reference Manual
280
INPUT PORT TRIM (Fine adjustment of the analog input gain)
Access the INPUT PORT TRIM window, and make fine adjustments to the gain of the
specified analog input port in 0.1 dB steps.
OUTPUT PORT TRIM (Fine adjustment of the output port gain)
Access the OUTPUT PORT TRIM window, and make fine adjustments to the gain of the
specified analog output port in 0.01 dB steps.
SLOT OUTPUT TRIM (Fine adjustment of the slot output port gain)
Access the SLOT OUTPUT TRIM window, and make fine adjustments to the gain of the
output ports of the specified slot in 0.01 dB steps.
Other functions
V5 Reference Manual
281
Adjusting the channel color (Calibration function)
If necessary, you can adjust the channel colors. Adjust the channel colors one by one.
NOTE
In the case of the CL3/CL1, channels that do not exist on
those models will not be shown.
You cannot adjust more than one channel simultaneously.
The APPLY button appears only if you change the RGB
values.
To reset all channel color indicators to the factory default
setting, press the RESET ALL button.
Once initialization is complete, you can continue operation
by selecting a different menu instead of pressing the EXIT
button.
Adjusting the brightness of the channel name
display
If necessary, you can adjust the brightness of the channel name display.
NOTE
Alternatively, you can continue operation by selecting a different menu instead of pressing the
EXIT button.
STEP
1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the
power to the CL unit.
2. On the startup menu screen, press the LED COLOR CALIBRATION button.
3. Press a [SEL] key on the top panel to select the indicator for which you want to adjust
the color.
4. Press one of the color buttons in the CHANNEL COLOR CALIBRATION MODE screen
to select the desired color.
5. While comparing the color of the selected channel’s indicator with the color of the
other channel indicators (for which the [SEL] keys are turned off), use multifunction
knobs 6, 7, and 8 to adjust the color.
6. When you have finished adjusting the color, press the APPLY button located in the
right of the screen to confirm the change.
7. Press the EXIT button on the startup menu screen to start up the CL unit in normal
operating mode.
CHANNEL COLOR CALIBRATION
MODE screen
STEP
1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the power
to the CL unit.
2. On the startup menu screen, press the LED COLOR CALIBRATION button.
3. Press the [CUE] key or [ON] key of the channel whose brightness you want to adjust.
Pressing the [CUE] key will increase the brightness, and pressing the [ON] key will
decrease the brightness.
4. When you have finished adjusting the brightness, press the APPLY button located in the
right of the screen to confirm the change.
5. Press the EXIT button on the startup menu screen to start up the CL unit in normal
operating mode.
Other functions
V5 Reference Manual
282
Adjusting the contrast of the channel name
display
If necessary, you can adjust the contrast of the channel name display.
NOTE
The APPLY button appears only if you change the setting.
Alternatively, you can continue operation by selecting a different menu instead of pressing the
EXIT button.
Initializing the console settings and Dante audio
network settings
It is possible for Dante-related settings to be initialized to their factory-set state when an error
occurs on the Dante audio network.
CAUTION
When you initialize, all console settings including the Dante audio network settings that had
been previously saved in memory will be lost.
Disconnect all connections from the Dante audio network before initializing.
STEP
1. While holding down the SCENE MEMORY [STORE] key on the panel, turn on the power
to the CL unit.
2. On the startup menu screen, press the LED COLOR CALIBRATION button.
3. Hold down a [SEL] key on the panel, and turn multifunction knob 1 in the Centralogic
section.
Turning the knob toward the left will lighten the contrast of all channels; turning it toward
the right will darken the contrast of all channels.
4. If you want to adjust a channel whose contrast differs from that of the other channels,
hold down the [SEL] key of the desired channel and press its [CUE] key or [ON] key.
Pressing the [CUE] key will darken the contrast, and pressing the [ON] key will lighten the contrast.
5. When you have finished adjusting the contrast, press the APPLY button located in the
right of the screen to confirm the change.
6. Press the EXIT button on the startup menu screen to start up the CL unit in normal
operating mode.
STEP
1. While holding down the SCENE MEMORY [STORE] key and [INC] key on the panel,
turn on the power to the CL unit.
2. A message indicates that initialization process is complete. Press the CLOSE button.
Other functions
V5 Reference Manual
283
Update procedure for NAME SUB CPU firmware
If the following window is displayed, the console has entered the mode for updating the NAME
SUB CPU firmware. For details about this operation, refer to the “CL5/CL3/CL1 Firmware
Update Guide.
Do not power-off the console while the update is proceeding.
To exit this mode, press the CANCEL button.
Update function to Dante firmware
If the following window is displayed, the console has entered the mode for updating the Dante
module firmware. For details about this operation, refer to the “CL5/CL3/CL1 Firmware
Update Guide.
Do not power-off the console while the update is proceeding.
To exit this mode, press the CANCEL button.
Warning/Error Messages
V5 Reference Manual
284
Warning/Error Messages
Message Meaning
5.1SOLO : Only input cue is enabled.
If switched to Surround mode, only the input channel can be cue-
monitored when CUE MODE is set to 5.1 SOLO. (Attempted to cue-
monitor a different channel.)
xxx Parameters Copied. Parameter xxx was copied to the copy buffer.
xxx Parameters Initialized. Parameter xxx was initialized.
xxx Parameters Pasted. Parameter xxx was pasted from the copy buffer.
xxx Parameters Swapped with Copy
Buffer.
Parameter xxx was exchanged with the contents of the copy buffer.
ALTERNATE FUNCTION: Turned off! ALTERNATE FUNCTION was turned off.
Cannot Assign!
In the USER DEFINED KEYS popup of the CL3/CL1, you attempted to
edit an item that cannot be edited for that model.
Cannot Bookmark This Popup. This popup window cannot be bookmarked.
Cannot Mount This Type of Device in
This Position.
You attempted to mount a specific device at a position where it cannot
be mounted.
Cannot Open This Page. This window cannot be opened.
Cannot Paste to Different Parameter
Type!
The parameter cannot be pasted to a different type.
Cannot Paste! Cannot paste the character string.
Cannot Recall! Failed to recall a scene memory or library.
Cannot Select This Channel.
You attempted to select a channel that cannot be operated due to your
user level or some other reason.
Cannot Store! Failed to store a scene memory or library.
Cannot Undo! You pressed the UNDO button when Undo was not available.
Channel Copied. Channel settings have been copied.
Channel Moved. Channel settings have been moved.
Channel Returned to Default Settings. Channel settings have been returned to the default settings.
Console initialized due to memory
mismatch.
All data has been initialized because the data in internal backup
memory has been lost, due to an update or failure of the backup
battery or some other reason. Please contact your Yamaha service
center listed at the end of the Owner’s Manual (separate document).
Corrupted data fixed! The data was fixed.
Couldn’t Access File. File on the USB flash drive could not be accessed for some reason.
Couldn’t Write File. File could not be saved to the USB flash drive.
Current User Changed. [xxx] Current user was changed to [xxx].
DANTE audio resource overflow. There are insufficient audio resources on the Dante audio network.
DANTE Connection Error!
The primary and secondary connections are incorrect in the daisy
chain connections.
DANTE is not working by GIGA bit. GIGA bit is not working on the Dante audio network.
DANTE is working at Secondary. The Dante audio network is working on a secondary port.
DANTE module Error! An error has occurred in a Dante module.
DANTE switched to secondary port.
Only the SECONDARY PORT is used, even though a CL series
console is being used via a redundant connection.
DCA ROLL-OUT : DCA members
scrolling.
In DCA ROLL-OUT mode, the content is scrolled left to right in the
block.
Different File Format! Some Data was
not Loaded.
Data in an unsupported format was loaded.
Directory Not Empty!
You attempted to delete a directory, but failed because there were files
remaining in the directory.
Editor: Data Framing Error!
Editor: Data Overrun!
Invalid signals are being exchanged with CL Editor.
Editor: Rx Buffer Full! Too much data is being received at CL Editor’s input port.
Editor: Tx Buffer Full! Too much data is being sent from CL Editor’s output port.
EFFECT CUE: Turned Off.
CUE was defeated because you switched from the EFFECT popup
window or the premium rack popup window to a different screen.
Error occurred at Secondary Port.
The network cable of a redundant secondary port has been
disconnected.
External HA Connection Conflict!
External HA data could not be recalled, because the state of
connections to the external HA has changed since the scene was
stored.
External Power Supply is Cut Off!
The PW800 (EXT) power supply connected to the CL series console
has stopped operating.
Fader Bank Snapshot is Done. A snapshot was taken of the current bank settings.
File Access is Busy!
The following operation has not been performed yet because the USB
flash drive is being accessed.
File Already Exists!
The USB flash drive already contains a file/directory with the same
name as the one you are attempting to save, rename, or create.
File Error [xx]! Internal file access error
File Protected!
Overwriting was not possible because the file on the USB flash drive
is write-protected.
Flash Memory Initializing Finished. Memory initialization has been completed.
Help File Not Found! The help file has not been loaded.
Illegal Address! The IP address or gateway address settings are invalid.
Illegal DIP Switch Setting. The R series DIP switch settings are invalid.
Illegal MAC Address! Cannot Use
Ethernet.
Communication via the Network connector is not possible because
the MAC address setting has been damaged for some reason.
Please contact your Yamaha service center listed at the end of the
Owner’s Manual (separate document).
Illegal MAC Address! The MAC Address is invalid.
Illegal Storage Format!
The USB flash drive could not be accessed because its format is
invalid or unsupported.
Message Meaning
Warning/Error Messages
V5 Reference Manual
285
Internal Power Supply is Cut Off!
The internal (INT) power supply has stopped operating. Alternatively,
some other problem has occurred. Please contact your Yamaha
service center listed at the end of the Owner’s Manual (separate
document).
Internal Power Supply is Turned On. The internal (INT) power supply has started up normally.
Invalid value
The MonitorMix application PIN that is set on the CL series console
must be a 4-digit numeric password.
KEY IN CUE: Turned Off.
KEY IN CUE was defeated because you switched from the
DYNAMICS 1 popup window of an input channel to a different screen.
LIBRARY #xxx is Empty! No data has been stored in library #xxx that you attempted to recall.
Loading Aborted. Loading from USB flash drive was aborted.
Loading Finished. Finished loading from USB flash drive.
Low Battery! The backup battery voltage is low.
Maximum Number of Audio Files
Exceeded!
The number of songs that can be managed by the USB memory
recorder has been exceeded.
Memory Error. The R series backup memory is corrupted.
MIDI: Data Framing Error!
MIDI: Data Overrun!
An inappropriate signal is being input to the MIDI input port.
MIDI: Rx Buffer Full! Too much data is being received at the MIDI input port.
MIDI: Tx Buffer Full! Too much data is being transmitted from the MIDI output port.
Monitor Assignment is Restricted to
Max. 8 Sources!
The Monitor Define function allows a maximum of eight sources to be
selected, but you attempted to assign more than eight.
No Access From Recorder!
In the RECORDER screen, it is not possible to move to a level higher
than \YPE\SONGS\.
No Channel Selected.
A copy-source channel was not selected in the GLOBAL PASTE
screen.
No Copy Item Selected.
In the GLOBAL PASTE screen, you attempted to paste without having
selected an item to paste.
No Corresponding Help Items. The corresponding section was not found in the Help file.
No ID3 Tag exists. You can not edit. The music file cannot be edited because it has no ID3 tag.
No Response from External HA. No response from an external AD8HR.
No Response from I/O DEVICE. The I/O devices not responding.
Operating as the word clock master. This console is the Clock Master.
Page Bookmarked. The current screen or popup has been bookmarked.
Parameter out of range!
Some data could not be loaded because the parameters do not
match.
Password Changed. The password has been changed.
PlayBack Failed: Recorder is Busy!
Audio file link playback is not possible because recording is in
progress.
PLAYBACK OUT CUE: Turned Off.
CUE was canceled for PLAYBACK OUT because you switched from
the RECORDER screen to another screen.
Please use Dante Controller. The Dante Patch settings from the console are not valid.
Message Meaning
Please wait, Dante patch is proceeding
now.
You attempted to edit in the DANTE PATCH screen at a time when
patching was not possible.
Power Supply Fan has Malfunctioned!
The cooling fan of the internal power supply has stopped. Please
contact your Yamaha service center listed at the end of the Owner’s
Manual (separate document).
PREVIEW Mode : Cannot Use This
Function.
The operation was ignored because this function cannot be used
during Preview.
PREVIEW Mode : Disabled Preview was disabled.
PREVIEW Mode : Enabled Preview was enabled.
Processing Aborted. Processing was interrupted.
Recorder Busy: Operation Aborted!
The button operation was canceled because recorder processing
required time.
RECORDER: CODEC Error [0x%08X] ! A codec error occurred in the RECORDER screen.
RECORDER IN CUE: Turned Off.
CUE was canceled for RECORDER IN because you switched from
the RECORDER screen to another screen.
Re-Enter Password!
When specifying the user password, the password was not entered a
second time.
REMOTE: Data Framing Error!
REMOTE: Data Overrun!
Invalid signals are being input to the Remote connector.
REMOTE: Rx Buffer Full! Too much data is being received at the Remote connector.
REMOTE: Tx Buffer Full! Too much data is being sent from the Remote connector.
Removed from the Channel Link group. The channel was removed from the link group.
Saving Aborted. Saving to the USB flash drive has been interrupted.
Saving Finished. Finished saving to USB flash drive.
SCENE #xxx is Empty!
No data has been stored in the scene you attempted to recall, or the
data has been damaged so that it cannot be recalled.
SCENE #xxx is Protected! You attempted to overwrite (store) a protected scene.
SCENE #xxx is Read Only! You attempted to overwrite (store) a read-only scene.
Scene Playback Link Canceled! The audio playback link for the scene was canceled.
SLOT x: Data Framing Error!
SLOT x: Data Overrun!
Invalid signals are being input to the SLOT x input port.
SLOT x: Rx Buffer Full! Too much data is being received at the SLOT x input port.
SLOT x: Tx Buffer Full! Too much data is being transmitted from the SLOT x output port.
Some Song Files Are Unidentified.
Some songs were not identified. Songs that have not been specified
might be used for DIRECT PLAY or SCENE PLAY BACK LINK.
Song File Not Found!
The file specified for SCENE LINK or DIRECT PLAY assigned to a
USER DEFINED key does not exist.
STAGEMIX: Data Framing Error!
STAGEMIX: Data Overrun!
Invalid signals are being exchanged with StageMix.
STAGEMIX: Rx Buffer Full! Too much data is being received at the StageMix input port.
STAGEMIX: Tx Buffer Full! Too much data is being transmitted from the StageMix output port.
Message Meaning
Warning/Error Messages
V5 Reference Manual
286
STEREO Mode : Cannot Use This
Function.
You cannot use this function in Stereo mode.
STEREO MODE ON. The console has switched to Stereo mode.
Storage Full!
The file could not be saved because there is insufficient space on the
USB flash drive.
Storage Not Found! The USB flash drive could not be recognized.
Storage Not Ready! Access is not possible because the USB flash drive is not ready.
SURROUND Mode : Cannot Use This
Function.
You cannot use this function in Surround mode.
SURROUND MODE ON. The console has switched to Surround mode.
Sync Error! [xxx] The CL series console is not synchronized to the [xxx] signal.
Tap Operation Ignored.
Tap operation was ignored because the TAP TEMPO button is not
displayed in the screen.
Target device is in WGM Mode.
Operation Denied.
Attempted to operate RMio64-D when the mounted RMio64-D is in
WGM mode (RMio64-D operating as a member of the NUAGE
Workgroup).
This Operation is Not Allowed.
This operation has been ignored because the current user does not
have permission.
This Operation is Not Allowed in This
View.
This function is not allowed in this screen.
Too Large File! Loading Failed.
Loading is not possible because the bitmap file is too large. The
maximum supported file size is 307,256 Bytes.
Or loading is not possible because the bitmap file is too large. The
maximum supported file size is 1024 kilobytes.
Too Many Bands Used! Cannot
Compare.
Copying 31BandGEQ and comparing it to Flex15GEQ has failed
because more than 15 bands are included in the copy source.
Too Many Bands Used! Cannot Paste to
Flex15GEQ.
Copying and pasting 31BandGEQ to Flex15GEQ has failed because
more than 15 bands are included in the copy source.
Total Slot Power Capability Exceeded!
Power consumption of the I/O cards installed in the slots has
exceeded the rated value.
Unassigned Encoder.
Your operation has been ignored because there is no parameter that
corresponds to the knob you operated.
Unit Fan has Malfunctioned The fan in the R series console has malfunctioned.
Unit ID Duplicated! The UNIT ID is duplicated on the Dante audio network.
Unsupported File Format!
The file you attempted to load from the USB flash drive is of an
unsupported format.
USB Currently Active for Recorder
function!
Save or Load operations are unavailable because the USB memory
recorder is recording or playing.
USB Currently Active for SAVE or LOAD!
The recorder cannot operate, since mixer scene memory or library
data is being saved to or loaded from the USB flash drive.
USB Memory Busy: Recorder Stopped!
Recording/playback stopped because time is required for USB flash
drive processing.
USB Memory Full !
Cant save the RECORDER playlist because there is insufficient free
space on the USB flash drive.
Message Meaning
USB Memory Full! Recorder Stopped.
Recorder processing was halted because the USB flash drive
capacity ran out while the USB memory recorder was operating.
USB Memory is Protected! The USB flash drive’s Protect setting is turned on.
USB Memory Unmounted! Recorder
Stopped.
Recorder processing was halted because the USB flash drive was
disconnected while the USB memory recorder was operating.
USB over current Error! Disconnect USB
device.
The USB device was disconnected because of excessive USB
current.
USER DEFINED KEY BANK CHANGED [x].
The bank for the USER DEFINED KEY has switched to [x]. (x is A, B,
C, or D.)
Version Changed. All Memories were
Initialized.
The current memory was initialized when the version was updated.
Version mismatch. The versions of this console and the R series console do not match.
Word Clock Error! Recorder Stopped!
Recorder was halted because synchronization to the word clock was
lost.
Wrong Audio File Format! The format of the audio file is invalid.
Wrong Password! The password you input was incorrect.
Wrong Word Clock!
The CL series console cannot synchronize because the source
selected by MASTER CLOCK SELECT in the WORD CLOCK screen
is not appropriate.
You Cannot Create User Key.
The current user does not have permission to create a user
authentication key.
Message Meaning
Index
V5 Reference Manual
287
Index
Numerics
8BandPEQ .................................................. 148
A
Assignable encoders ................................... 234
Audio file (links to a scene recall)................ 110
AUTOMIXER ............................................... 151
B
BUS SETUP window ................................... 252
C
Calibration ................................... 278, 279, 281
Cascade connections .................................. 248
Centralogic section........................................ 13
Channel color ................................ 31, 253, 281
Channel Job .................................................. 74
Channel library ........................................ 55, 64
Channel Link ................................................. 85
Console Lock............................................... 238
Control change
Control parameters.................................. 197
Copying, moving, or initializing a channel ..... 90
Cue...................................................... 113, 120
Operating................................................. 122
Custom fader bank ...................................... 236
D
Dante audio network ............................. 18, 256
Dante Device Lock ...................................... 258
Dante Domain Manager .............................. 259
DAW ............................................................ 206
DCA group..................................................... 74
Directly outputting.......................................... 26
Dynamics................................................. 65, 69
Libraries..................................................... 73
E
Effect ........................................................... 140
Libraries................................................... 172
Effects and tempo synchronization ............. 160
EQ ................................................................. 65
Libraries..................................................... 73
External head amps ............................ 173, 187
F
Factory set ................................................... 278
Fade function ............................................... 106
Focus Recall function................................... 105
Function Tree................................................... 4
Functions that can be assigned to
the assignable encoders............................. 235
G
Gain ............................................................... 32
Analog gain ................................................ 32
Gain Compensation ....................................... 38
Global Paste function................................... 102
GPI............................................................... 271
Graphic EQ .......................................... 140, 144
Libraries ................................................... 172
H
HA .................................................................. 32
Head Amp ...................................................... 32
Help function ................................................ 276
I
I/O devices ................................................... 173
Initializing ..................................................... 278
Input channels................................................ 29
Channel library ........................................... 55
Sending to MIX/MATRIX bus ..................... 43
Sending to STEREO/MONO bus ............... 38
Specifying channel name and icon ............ 30
Input Delay..................................................... 48
Input patch ..................................................... 19
Inserting ......................................................... 23
Internal clock................................................ 254
Internal effects ............................................. 154
L
Lamp brightness .......................................... 253
LED .............................................................. 253
Library ............................................ 73, 172, 195
M
Master fader................................................. 237
MATRIX buses....................................... 60, 252
MBCL (option).............................................. 139
Meter bridge (option).................................... 139
METER screen............................................. 134
Meters.......................................................... 134
MIDI ............................................................. 192
MIX buses.................................................... 252
MIX channels
Sending to MATRIX buses ........................ 60
Sending to STEREO/MONO bus............... 58
MIX MINUS.................................................... 94
MIX/MATRIX buses ....................................... 43
Monitor................................................. 113, 114
Mute group .................................................... 79
N
Name displays ............................................. 253
Network address.......................................... 254
Nuendo Live ................................................ 209
O
Oscillator.............................................. 129, 131
Output channels ............................................ 56
Channel library........................................... 64
Specifying channel name and icon ............ 57
Output Delay.................................................. 63
Output patch .................................................. 21
OVERVIEW Screen....................................... 14
P
Parameter changes ..................................... 199
Patching......................................................... 18
Pink frame (TOUCH AND TURN)................ 231
Preferences ................................................. 222
Premium Rack ............................................. 161
Libraries ................................................... 172
Using........................................................ 161
PREVIEW mode .......................................... 112
Program change .......................................... 195
R
Recall Safe function....................................... 82
REMOTE HA ............................................... 267
RTA ............................................................. 136
S
Scene
Editing...................................................... 100
SELECTED CHANNEL section ....................... 6
SELECTED CHANNEL VIEW screen ............. 7
Setup ........................................................... 213
SETUP screen............................................. 213
Signal quality meter....................... 33, 184, 185
Slot .............................................................. 246
Solo function................................................ 125
STEREO/MONO bus............................... 38, 58
STEREO/MONO channels
Sending to MATRIX buses ........................ 60
Surround...................................................... 118
SURROUND SETUP screen....................... 214
T
Talkback ...................................................... 129
Title list ........................................................ 205
TOUCH AND TURN .................................... 231
Touch screen............................................... 253
U
USB flash drive
Formatting ............................................... 245
Help/text file loading ................................ 276
Loading a file ........................................... 242
Playing back audio files........................... 204
Recording ................................................ 202
Saving and loading setup data ................ 239
USB memory recorder................................. 200
Assigning channels ................................. 200
USER DEFINED keys ................................. 224
Functions that can be assigned............... 226
Recalling Help ......................................... 277
USER DEFINED knobs ............................... 231
Functions that can be assigned............... 232
User settings ............................................... 215
V
Virtual rack .................................................. 140
Operations............................................... 141
W
Warning/Error Messages............................. 284
WIRELESS.................................................. 183
Word clock................................................... 246
EN
Table of Contents
EQ Library List....................................................................... 2
DYNAMICS Library List ......................................................... 3
Dynamics Parameters............................................................ 5
Effect Type List....................................................................... 7
Effects Parameters................................................................. 8
Premium Rack Processor Parameters .................................. 20
Parameters That Can Be Assigned to Control Changes....... 23
NRPN Parameter Assignments ............................................ 27
Mixing Parameter Operation Applicability............................. 31
MIDI Data Format ................................................................. 37
Input/Output Characteristics ................................................. 44
Electrical Characteristics ...................................................... 46
Mixer Basic Parameters........................................................ 47
Pin Assignment..................................................................... 48
MIDI Implementation Chart................................................... 49
Data List
Data List
2
EQ Library List
Libraries created by the user also include type parameters
and BYPASS parameters (ON/OFF) for each band.
The type parameter for all read-only presets is “LEGACY
(TYPE1).
# Title
Parameter
LOW L-MID H-MID HIGH
01 Bass Drum 1
PEAKING PEAKING PEAKING H.SHELF
G +3.5 dB -3.5 dB 0.0 dB +4.0 dB
F 100 Hz 265 Hz 1.06 kHz 5.30 kHz
Q 1.25 10.0 0.90 -
02 Bass Drum 2
PEAKING PEAKING PEAKING LPF
G +8.0 dB -7.0 dB +6.0 dB ON
F 80.0 Hz 400 Hz 2.50 kHz 12.5 kHz
Q 1.4 4.5 2.2 -
03 Snare Drum 1
PEAKING PEAKING PEAKING H.SHELF
G -0.5 dB 0.0 dB +3.0 dB +4.5 dB
F 132 Hz 1.00 kHz 3.15 kHz 5.00 kHz
Q 1.25 4.5 0.11 -
04 Snare Drum 2
L.SHELF PEAKING PEAKING PEAKING
G +1.5 dB -8.5 dB +2.5 dB +4.0 dB
F 180 Hz 335 Hz 2.36 kHz 4.00 kHz
Q - 10.0 0.70 0.10
05 Tom-tom 1
PEAKING PEAKING PEAKING PEAKING
G +2.0 dB -7.5 dB +2.0 dB +1.0 dB
F 212 Hz 670 Hz 4.50 kHz 6.30 kHz
Q 1.4 10.0 1.25 0.28
06 Cymbal
L.SHELF PEAKING PEAKING H.SHELF
G -2.0 dB 0.0 dB 0.0 dB +3.0 dB
F 106 Hz 425 Hz 1.06 kHz 13.2 kHz
Q - 8.0 0.90 -
07 High Hat
L.SHELF PEAKING PEAKING H.SHELF
G -4.0 dB -2.5 dB +1.0 dB +0.5 dB
F 95.0 Hz 425 Hz 2.80 kHz 7.50 kHz
Q -0.501.0 -
08 Percussion
L.SHELF PEAKING PEAKING H.SHELF
G -4.5 dB 0.0 dB +2.0 dB 0.0 dB
F 100 Hz 400 Hz 2.80 kHz 17.0 kHz
Q - 4.5 0.56 -
09 E. Bass 1
L.SHELF PEAKING PEAKING H.SHELF
G -7.5 dB +4.5 dB +2.5 dB 0.0 dB
F 35.5 Hz 112 Hz 2.00 kHz 4.00 kHz
Q -5.04.5-
10 E. Bass 2
PEAKING PEAKING PEAKING H.SHELF
G +3.0 dB 0.0 dB +2.5 dB +0.5 dB
F 112 Hz 112 Hz 2.24 kHz 4.00 kHz
Q 0.10 5.0 6.3 -
11 Syn. Bass 1
PEAKING PEAKING PEAKING H.SHELF
G +3.5 dB +8.5 dB 0.0 dB 0.0 dB
F 85.0 Hz 950 Hz 4.00 kHz 12.5 kHz
Q 0.10 8.0 4.5 -
12 Syn. Bass 2
PEAKING PEAKING PEAKING H.SHELF
G +2.5 dB 0.0 dB +1.5 dB 0.0 dB
F 125 Hz 180 Hz 1.12 kHz 12.5 kHz
Q 1.6 8.0 2.2 -
13 Piano 1
L.SHELF PEAKING PEAKING H.SHELF
G -6.0 dB 0.0 dB +2.0 dB +4.0 dB
F 95.0 Hz 950 Hz 3.15 kHz 7.50 kHz
Q -8.00.90-
14 Piano 2
PEAKING PEAKING PEAKING H.SHELF
G +3.5 dB -8.5 dB +1.5 dB +3.0 dB
F 224 Hz 600 Hz 3.15 kHz 5.30 kHz
Q 5.6 10.0 0.70 -
15 E. G. Clean
PEAKING PEAKING PEAKING H.SHELF
G +2.0 dB -5.5 dB +0.5 dB +2.5 dB
F 265 Hz 400 Hz 1.32 kHz 4.50 kHz
Q 0.18 10.0 6.3 -
16 E. G. Crunch 1
PEAKING PEAKING PEAKING PEAKING
G +4.5 dB 0.0 dB +4.0 dB +2.0 dB
F 140 Hz 1.00 kHz 1.90 kHz 5.60 kHz
Q 8.0 4.5 0.63 9.0
17 E. G. Crunch 2
PEAKING PEAKING PEAKING H.SHELF
G +2.5 dB +1.5 dB +2.5 dB 0.0 dB
F 125 Hz 450 Hz 3.35 kHz 19.0 kHz
Q 8.0 0.40 0.16 -
18 E. G. Dist. 1
L.SHELF PEAKING PEAKING H.SHELF
G +5.0 dB 0.0 dB +3.5 dB 0.0 dB
F 355 Hz 950 Hz 3.35 kHz 12.5 kHz
Q -9.010.0-
19 E. G. Dist. 2
L.SHELF PEAKING PEAKING H.SHELF
G +6.0 dB -8.5 dB +4.5 dB +4.0 dB
F 315 Hz 1.06 kHz 4.25 kHz 12.5 kHz
Q - 10.0 4.0 -
20 A. G. Stroke 1
PEAKING PEAKING PEAKING H.SHELF
G -2.0 dB 0.0 dB +1.0 dB +4.0 dB
F 106 Hz 1.00 kHz 1.90 kHz 5.30 kHz
Q 0.90 4.5 3.5 -
# Title
Parameter
LOW L-MID H-MID HIGH
21 A. G. Stroke 2
L.SHELF PEAKING PEAKING H.SHELF
G -3.5 dB -2.0 dB 0.0 dB +2.0 dB
F 300 Hz 750 Hz 2.00 kHz 3.55 kHz
Q -9.04.5-
22 A. G. Arpeg. 1
L.SHELF PEAKING PEAKING PEAKING
G -0.5 dB 0.0 dB 0.0 dB +2.0 dB
F 224 Hz 1.00 kHz 4.00 kHz 6.70 kHz
Q -4.54.50.125
23 A. G. Arpeg. 2
L.SHELF PEAKING PEAKING H.SHELF
G 0.0 dB -5.5 dB 0.0 dB +4.0 dB
F 180 Hz 355 Hz 4.00 kHz 4.25 kHz
Q -7.04.5-
24 Brass Sec.
PEAKINGPEAKINGPEAKINGPEAKING
G -2.0 dB -1.0 dB +1.5 dB +3.0 dB
F 90.0 Hz 850 Hz 2.12 kHz 4.50 kHz
Q 2.8 2.0 0.70 7.0
25 Male Vocal 1
PEAKINGPEAKINGPEAKINGPEAKING
G -0.5 dB 0.0 dB +2.0 dB +3.5 dB
F 190 Hz 1.00 kHz 2.00 kHz 6.70 kHz
Q 0.11 4.5 0.56 0.11
26 Male Vocal 2
PEAKING PEAKING PEAKING H.SHELF
G +2.0 dB -5.0 dB -2.5 dB +4.0 dB
F 170 Hz 236 Hz 2.65 kHz 6.70 kHz
Q 0.11 10.0 5.6 -
27 Female Vo. 1
PEAKINGPEAKINGPEAKINGPEAKING
G -1.0 dB +1.0 dB +1.5 dB +2.0 dB
F 118 Hz 400 Hz 2.65 kHz 6.00 kHz
Q 0.18 0.45 0.56 0.14
28 Female Vo. 2
L.SHELF PEAKING PEAKING H.SHELF
G -7.0 dB +1.5 dB +1.5 dB +2.5 dB
F 112 Hz 335 Hz 2.00 kHz 6.70 kHz
Q -0.160.20-
29 Chorus & Harmo
PEAKINGPEAKINGPEAKINGPEAKING
G -2.0 dB -1.0 dB +1.5 dB +3.0 dB
F 90.0 Hz 850 Hz 2.12 kHz 4.50 kHz
Q 2.8 2.0 0.70 7.0
30 Total EQ 1
PEAKING PEAKING PEAKING H.SHELF
G -0.5 dB 0.0 dB +3.0 dB +6.5 dB
F 95.0 Hz 950 Hz 2.12 kHz 16.0 kHz
Q 7.0 2.2 5.6 -
31 Total EQ 2
PEAKING PEAKING PEAKING H.SHELF
G +4.0 dB +1.5 dB +2.0 dB +6.0 dB
F 95.0 Hz 750 Hz 1.80 kHz 18.0 kHz
Q 7.0 2.8 5.6 -
# Title
Parameter
LOW L-MID H-MID HIGH
Data List
3
DYNAMICS Library List
32 Total EQ 3
L.SHELF PEAKING PEAKING H.SHELF
G +1.5 dB +0.5 dB +2.0 dB +4.0 dB
F 67.0 Hz 850 Hz 1.90 kHz 15.0 kHz
Q - 0.28 0.70 -
33 Bass Drum 3
PEAKING PEAKING PEAKING PEAKING
G +3.5 dB -10.0 dB +3.5 dB 0.0 dB
F 118 Hz 315 Hz 4.25 kHz 20.0 kHz
Q 2.0 10.0 0.40 0.40
34 Snare Drum 3
L.SHELF PEAKING PEAKING PEAKING
G 0.0 dB +2.0 dB +3.5 dB 0.0 dB
F 224 Hz 560 Hz 4.25 kHz 4.00 kHz
Q -4.52.80.10
35 Tom-tom 2
L.SHELF PEAKING PEAKING H.SHELF
G -9.0 dB +1.5 dB +2.0 dB 0.0 dB
F 90.0 Hz 212 Hz 5.30 kHz 17.0 kHz
Q - 4.5 1.25 -
36 Piano 3
PEAKING PEAKING PEAKING H.SHELF
G +4.5 dB -13.0 dB +4.5 dB +2.5 dB
F 100 Hz 475 Hz 2.36 kHz 10.0 kHz
Q 8.0 10.0 9.0 -
37 Piano Low
PEAKING PEAKING PEAKING H.SHELF
G -5.5 dB +1.5 dB +6.0 dB 0.0 dB
F 190 Hz 400 Hz 6.70 kHz 12.5 kHz
Q 10.0 6.3 2.2 -
38 Piano High
PEAKING PEAKING PEAKING PEAKING
G -5.5 dB +1.5 dB +5.0 dB +3.0 dB
F 190 Hz 400 Hz 6.70 kHz 5.60 kHz
Q 10.0 6.3 2.2 0.10
39 Fine-EQ Cass
L.SHELF PEAKING PEAKING H.SHELF
G -1.5 dB 0.0 dB +1.0 dB +3.0 dB
F 75.0 Hz 1.00 kHz 4.00 kHz 12.5 kHz
Q -4.51.8-
40 Narrator
PEAKING PEAKING PEAKING H.SHELF
G -4.0 dB -1.0 dB +2.0 dB 0.0 dB
F 106 Hz 710 Hz 2.50 kHz 10.0 kHz
Q 4.0 7.0 0.63 -
# Title
Parameter
LOW L-MID H-MID HIGH
# Title Type Parameter Value
1Gate GATE
Threshold (dB) -26
Range (dB) -56
Attack (ms) 0
Hold (ms) 2.56
Decay (ms) 331
2Ducking DUCKING
Threshold (dB) -19
Range (dB) -22
Attack (ms) 93
Hold (ms) 1.20 S
Decay (ms) 6.32 S
3A. Dr. BD GATE
Threshold (dB) -11
Range (dB) -53
Attack (ms) 0
Hold (ms) 1.93
Decay (ms) 400
4A. Dr. SN GATE
Threshold (dB) -8
Range (dB) -23
Attack (ms) 1
Hold (ms) 0.63
Decay (ms) 238
5De-Esser DE-ESSER
Threshold (dB) -8
Frequency (kHz) 2.00
Type HPF
Q1.6
6Comp COMPRESSOR
Threshold (dB) -8
Ratio ( :1) 2.5
Attack (ms) 30
Out gain (dB) 0.0
Knee 2
Release (ms) 250
7Expand EXPANDER
Threshold (dB) -23
Ratio ( :1) 1.7
Attack (ms) 1
Out gain (dB) 3.5
Knee 2
Release (ms) 70
8Compander (H)COMPANDER-H
Threshold (dB) -10
Ratio ( :1) 3.5
Attack (ms) 1
Out gain (dB) 0.0
Width (dB) 6
Release (ms) 250
9Compander (S)COMPANDER-S
Threshold (dB) -8
Ratio ( :1) 4
Attack (ms) 25
Out gain (dB) 0.0
Width (dB) 24
Release (ms) 180
10 A. Dr. BD COMPRESSOR
Threshold (dB) -24
Ratio ( :1) 3
Attack (ms) 9
Out gain (dB) 5.5
Knee 2
Release (ms) 58
11 A. Dr. BD COMPANDER-H
Threshold (dB) -11
Ratio ( :1) 3.5
Attack (ms) 1
Out gain (dB) -1.5
Width (dB) 7
Release (ms) 192
12 A. Dr. SN COMPRESSOR
Threshold (dB) -17
Ratio ( :1) 2.5
Attack (ms) 8
Out gain (dB) 3.5
Knee 2
Release (ms) 12
13 A. Dr. SN EXPANDER
Threshold (dB) -23
Ratio ( :1) 2
Attack (ms) 0
Out gain (dB) 0.5
Knee 2
Release (ms) 151
14 A. Dr. SN COMPANDER-S
Threshold (dB) -8
Ratio ( :1) 1.7
Attack (ms) 11
Out gain (dB) 0.0
Width (dB) 10
Release (ms) 128
15 A. Dr. Tom EXPANDER
Threshold (dB) -20
Ratio ( :1) 2
Attack (ms) 2
Out gain (dB) 5.0
Knee 2
Release (ms) 749
16 A. Dr. OverTop COMPANDER-S
Threshold (dB) -24
Ratio ( :1) 2
Attack (ms) 38
Out gain (dB) -3.5
Width (dB) 54
Release (ms) 842
17 E. B. Finger COMPRESSOR
Threshold (dB) -12
Ratio ( :1) 2
Attack (ms) 15
Out gain (dB) 4.5
Knee 2
Release (ms) 470
# Title Type Parameter Value
Data List
4
* At fs=44.1 kHz
18 E. B. Slap COMPRESSOR
Threshold (dB) -12
Ratio ( :1) 1.7
Attack (ms) 6
Out gain (dB) 4.0
Knee hard
Release (ms) 133
19 Syn. Bass COMPRESSOR
Threshold (dB) -10
Ratio ( :1) 3.5
Attack (ms) 9
Out gain (dB) 3.0
Knee hard
Release (ms) 250
20 Piano1 COMPRESSOR
Threshold (dB) -9
Ratio ( :1) 2.5
Attack (ms) 17
Out gain (dB) 1.0
Knee hard
Release (ms) 238
21 Piano2 COMPRESSOR
Threshold (dB) -18
Ratio ( :1) 3.5
Attack (ms) 7
Out gain (dB) 6.0
Knee 2
Release (ms) 174
22 E. Guitar COMPRESSOR
Threshold (dB) -8
Ratio ( :1) 3.5
Attack (ms) 7
Out gain (dB) 2.5
Knee 4
Release (ms) 261
23 A. Guitar COMPRESSOR
Threshold (dB) -10
Ratio ( :1) 2.5
Attack (ms) 5
Out gain (dB) 1.5
Knee 2
Release (ms) 238
24 Strings1 COMPRESSOR
Threshold (dB) -11
Ratio ( :1) 2
Attack (ms) 33
Out gain (dB) 1.5
Knee 2
Release (ms) 749
25 Strings2 COMPRESSOR
Threshold (dB) -12
Ratio ( :1) 1.5
Attack (ms) 93
Out gain (dB) 1.5
Knee 4
Release (ms) 1.35 s
# Title Type Parameter Value
26 Strings3 COMPRESSOR
Threshold (dB) -17
Ratio ( :1) 1.5
Attack (ms) 76
Out gain (dB) 2.5
Knee 2
Release (ms) 186
27 BrassSection COMPRESSOR
Threshold (dB) -18
Ratio ( :1) 1.7
Attack (ms) 18
Out gain (dB) 4.0
Knee 1
Release (ms) 226
28 Syn. Pad COMPRESSOR
Threshold (dB) -13
Ratio ( :1) 2
Attack (ms) 58
Out gain (dB) 2.0
Knee 1
Release (ms) 238
29 SamplingPerc COMPANDER-S
Threshold (dB) -18
Ratio ( :1) 1.7
Attack (ms) 8
Out gain (dB) -2.5
Width (dB) 18
Release (ms) 238
30 Sampling BD COMPRESSOR
Threshold (dB) -14
Ratio ( :1) 2
Attack (ms) 2
Out gain (dB) 3.5
Knee 4
Release (ms) 35
31 Sampling SN COMPRESSOR
Threshold (dB) -18
Ratio ( :1) 4
Attack (ms) 8
Out gain (dB) 8.0
Knee hard
Release (ms) 354
32 Hip Comp COMPANDER-S
Threshold (dB) -23
Ratio ( :1) 20
Attack (ms) 15
Out gain (dB) 0.0
Width (dB) 15
Release (ms) 163
33 Solo Vocal1 COMPRESSOR
Threshold (dB) -20
Ratio ( :1) 2.5
Attack (ms) 31
Out gain (dB) 2.0
Knee 1
Release (ms) 342
# Title Type Parameter Value
34 Solo Vocal2 COMPRESSOR
Threshold (dB) -8
Ratio ( :1) 2.5
Attack (ms) 26
Out gain (dB) 1.5
Knee 3
Release (ms) 331
35 Chorus COMPRESSOR
Threshold (dB) -9
Ratio ( :1) 1.7
Attack (ms) 39
Out gain (dB) 2.5
Knee 2
Release (ms) 226
36 Click Erase EXPANDER
Threshold (dB) -33
Ratio ( :1) 2
Attack (ms) 1
Out gain (dB) 2.0
Knee 2
Release (ms) 284
37 Announcer COMPANDER-H
Threshold (dB) -14
Ratio ( :1) 2.5
Attack (ms) 1
Out gain (dB) -2.5
Width (dB) 18
Release (ms) 180
38 Limiter1 COMPANDER-S
Threshold (dB) -9
Ratio ( :1) 3
Attack (ms) 20
Out gain (dB) -3.0
Width (dB) 90
Release (ms) 3.90 s
39 Limiter2 COMPRESSOR
Threshold (dB) 0
Ratio ( :1)
Attack (ms) 0
Out gain (dB) 0.0
Knee hard
Release (ms) 319
40 Total Comp1 COMPRESSOR
Threshold (dB) -18
Ratio ( :1) 3.5
Attack (ms) 94
Out gain (dB) 2.5
Knee hard
Release (ms) 447
41 Total Comp2 COMPRESSOR
Threshold (dB) -16
Ratio ( :1) 6
Attack (ms) 11
Out gain (dB) 6.0
Knee 1
Release (ms) 180
# Title Type Parameter Value
Data List
5
Dynamics Parameters
Dynamics Parameters are the following types.
GATE
A gate attenuates signals below a set THRESHOLD level by a specified amount (RANGE).
DUCKING
Ducking is commonly used for voice-over applications in which the background music level is
reduced automatically when an announcer speaks.
When the KEY IN source signal level exceeds the specified THRESHOLD, the output level is
attenuated by a specified amount (RANGE).
Input channels Output channels
DYNAMIC section 1 DYNAMIC section 2 DYNAMIC section 1
Type
GATE COMPRESSOR COMPRESSOR
DUCKING
COMPANDER-H
(Compander Hard)
EXPANDER
COMPRESSOR
COMPANDER-S
(Compander Soft)
COMPANDER-H
(Compander Hard)
EXPANDER DE-ESSER
COMPANDER-S
(Compander Soft)
Parameter Range Description
THRESHOLD (dB) -72 to 0 (73 points)
This determines the level at which the gate
effect is applied.
RANGE (dB) -∞, -69 to 0 (71 points)
This determines the amount of attenuation
when the gate closes.
ATTACK (ms) 0-120 (121 points)
This determines how fast the gate opens when
the signal exceeds the threshold level.
HOLD (ms)
44.1kHz: 0.02 ms - 2.13 sec
48kHz: 0.02 ms - 1.96 sec (160 points)
This determines how long the gate stays open
once the trigger signal has fallen below the
threshold.
DECAY (ms)
44.1kHz: 6 ms - 46.0 sec
48kHz: 5 ms - 42.3 sec (160 points)
This determines how fast the gate closes once
the hold time has expired. The value is
expressed as the duration required for the level
to change by 6 dB.
Input Level
Time
Time
Output Level
Input Level
Output Level
I/O Characteristics Time Series Analysis
RANGE
THRESHOLD
THRESHOLD
RANGE
Input Signal Output Signal
ATTACK DECAY
HOLD
Parameter Range Description
THRESHOLD (dB) -54 to 0 (55 points)
This determines the level of trigger signal
(KEY IN) required to activate ducking.
RANGE (dB) -70 to 0 (71 points)
This determines the amount of attenuation
when ducking is activated.
ATTACK (ms) 0-120 (121 points)
This determines how soon the signal is ducked
once the ducker has been triggered.
HOLD (ms)
44.1kHz: 0.02 ms - 2.13 sec
48kHz: 0.02 ms - 1.96 sec (160 points)
This determines how long ducking remains
active once the trigger signal has fallen below
the THRESHOLD level.
DECAY (ms)
44.1kHz: 6 ms - 46.0 sec
48kHz: 5 ms - 42.3 sec (160 points)
This determines how soon the ducker returns
to its normal gain once the trigger signal level
drops below the threshold. The value is
expressed as the duration required for the level
to change by 6 dB.
Input Level Time Time
Output Level
Input Level
Output Level
I/O Characteristics Time Series Analysis
RANGE
THRESHOLD
THRESHOLD
RANGE
Input Signal Output Signal
ATTACK DECAY
HOLD
Data List
6
COMPRESSOR
The COMP processor attenuates signals above a specified THRESHOLD by a specified
RATIO.
The COMP processor can also be used as a limiter, which, with a RATIO of ∞:1, reduces the
level to the threshold. This means that the limiter's output level never actually exceeds the
threshold.
EXPANDER
An expander attenuates signals below a specified THRESHOLD by a specified RATIO.
Parameter Range Description
THRESHOLD (dB) -54 to 0 (55 points)
This determines the level at which
compression is applied.
RATIO
1.0:1, 1.1:1, 1.3:1, 1.5:1, 1.7:1, 2.0:1,
2.5:1, 3.0:1, 3.5:1, 4.0:1, 5.0:1, 6.0:1,
8.0:1, 10:1, 20:1, ∞:1 (16 points)
This determines the amount of compression,
that is, the change in output signal level
relative to change in input signal level.
ATTACK (ms) 0-120 (121 points)
This determines how soon the signal will be
compressed once the compressor has been
triggered.
RELEASE (ms)
44.1kHz: 6 ms - 46.0 sec
48kHz: 5 ms - 42.3 sec (160 points)
This determines how soon the compressor
returns to its normal gain once the trigger
signal level drops below the threshold. The
value is expressed as the duration required for
the level to change by 6 dB.
OUT GAIN (dB) 0.0 to +18.0 (181 points)
This sets the compressor's output signal level.
KNEE Hard, 1-5 (6 points)
This determines how compression is applied
at the threshold. For higher knee settings,
compression is applied gradually as the signal
exceeds the specified threshold, creating a
more natural sound.
Input Level Time Time
Output Level
Input Level
Output Level
I/O Characteristics
(KNEE= hard,
OUT GAIN= 0.0dB)
Time Series Analysis
(RATIO= ∞:1)
RATIO
THRESHOLD
THRESHOLD
Input Signal Output Signal
ATTACK RELEASE
Parameter Range Description
THRESHOLD (dB) -54 to 0 (55 points)
This determines the level of input signal
required to trigger the expander.
RATIO
1.0:1, 1.1:1, 1.3:1, 1.5:1, 1.7:1, 2.0:1,
2.5:1, 3.0:1, 3.5:1, 4.0:1, 5.0:1, 6.0:1,
8.0:1, 10:1, 20:1, ∞:1 (16 points)
This determines the amount of expansion.
ATTACK (ms) 0-120 (121 points)
This determines how soon the expander
returns to its normal gain once the trigger
signal level exceeds the threshold.
RELEASE (ms)
44.1kHz: 6 ms - 46.0 sec
48kHz: 5 ms - 42.3 sec (160 points)
This determines how soon the signal is
expanded once the signal level drops below
the threshold. The value is expressed as the
duration required for the level to change by 6
dB.
OUT GAIN (dB) 0.0 to +18.0 (181 points)
This sets the expander's output signal level.
KNEE Hard, 1-5 (6 points)
This determines how expansion is applied at
the threshold. For higher knee settings,
expansion is applied gradually as the signal
exceeds the specified threshold, creating a
more natural sound.
Input Level Time Time
Output Level
Input Level
Output Level
I/O Characteristics
(KNEE= hard,
OUT GAIN= 0.0dB)
Time Series Analysis
(RATIO= ∞:1)
RATIO
THRESHOLD
THRESHOLD
Input Signal Output Signal
ATTACK RELEASE
Data List
7
COMPANDER HARD (COMPANDER-H), COMPANDER SOFT (COMPANDER-S)
The hard and soft companders combine the effects of the compressor, expander and limiter.
The companders function differently at the following levels:
1 0 dB and higher ..................................Functions as a limiter.
2 Exceeding the threshold ....................Functions as a compressor.
3 Below the threshold and width ..........Functions as an expander.
The hard compander has an expansion ratio of 5:1, while the soft compander has an
expansion ratio of 1.5:1. The expander is essentially turned off when the width is set to
maximum. The compressor has a fixed knee setting of 2.
* The gain is automatically adjusted according to the ratio and threshold values, and can be increased by up to 18 dB.
* The OUT GAIN parameter enables you to compensate for the overall level change caused by the compression and
expansion processes.
DE-ESSER
This detects and compresses only the sibilants and other high-frequency consonants of the
vocal.
Effect Type List
Parameter Range Description
THRESHOLD (dB) -54 to 0 (55 points)
This determines the level at which compression is
applied.
RATIO
1.0:1, 1.1:1, 1.3:1, 1.5:1, 1.7:1, 2.0:1,
2.5:1, 3.0:1, 3.5:1, 4.0:1, 5.0:1, 6.0:1,
8.0:1, 10:1, 20:1 (15 points)
This determines the amount of compression.
ATTACK (ms) 0-120 (121 points)
This determines how soon the signal is compressed or
expanded once the compander has been triggered.
RELEASE (ms)
44.1kHz: 6 ms - 46.0 sec
48kHz: 5 ms - 42.3 sec (160 points)
This determines how soon the compressor or
expander returns to the normal gain once the trigger
signal level drops below or exceeds the threshold
respectively. The value is expressed as the duration
required for the level to change by 6 dB.
OUT GAIN (dB) -18.0 to 0.0 (181 points) This sets the compressor's output signal level.
WIDTH (dB) 1-90 (90 points)
This determines how far below the threshold
expansion will be applied. The expander is activated
when the level drops below the threshold and width.
Parameter Range Description
THRESHOLD -54 to 0 (55 points) Threshold level at which the de-esser effect is applied.
FREQUENCY 1kHz-12.5kHz (45 points)
Cutoff frequency of the filter used to detect the high
frequencies.
TYPE HPF, BPF Type of filter used to detect the frequency band.
Q 10.0-0.10 (41 points) Q (steepness) of the filter when TYPE is BPF.
0dB
Input Level
Output Level
WIDTH
THRESHOLD
Title Type Description
REV-X Hall REV-X HALL New reverb algorithm that delivers dense and rich reverberation, smooth decay,
and provides a spaciousness and depth that enhances the original sound.
Choose from three types depending on your location and needs: REV-X HALL,
REV-X ROOM, and REV-X PLATE.
REV-X Room REV-X ROOM
REV-X Plate REV-X PLATE
Reverb Hall REVERB HALL Concert hall reverberation simulation with gate
Reverb Room REVERB ROOM Room reverberation simulation with gate
Reverb Stage REVERB STAGE Reverb designed for vocals, with gate
Reverb Plate REVERB PLATE Plate reverb simulation with gate
Stereo Reverb ST REVERB Stereo reverb
Early Ref. EARLY REF. Early reflections without the subsequent reverb
Gate Reverb GATE REVERB Gated early reflections
Reverse Gate REVERSE GATE Gated reverse early reflections
Mono Delay MONO DELAY Simple mono delay
Stereo Delay STEREO DELAY Simple stereo delay
Mod.Delay MOD.DELAY Simple repeat delay with modulation
Delay LCR DELAY LCR 3-tap (left, center, right) delay
Echo ECHO Stereo delay with crossed left/right feedback
Chorus CHORUS Chorus
Flange FLANGE Flanger
Symphonic SYMPHONIC
Proprietary Yamaha effect that produces a richer and more complex modulation
than normal chorus
Phaser PHASER 16-stage stereo phase shifter
Dyna.Flange DYNA.FLANGE Dynamically controlled flanger
Dyna.Phaser DYNA.PHASER Dynamically controlled phase shifter
HQ. Pitch HQ.PITCH Mono pitch shifter, producing stable results
Dual Pitch DUAL PITCH Stereo pitch shifter
Tremolo TREMOLO Tremolo
Auto Pan AUTO PAN Auto-panner
Rotary ROTARY Rotary speaker simulation
Ring Mod. RING MOD. Ring modulator
Mod.Filter MOD.FILTER Modulated filter
Dyna.Filter DYNA.FILTER Dynamically controlled filter
Rev+Chorus REV+CHORUS Reverb and chorus in parallel
RevChorus REVCHORUS Reverb and chorus in series
Rev+Flange REV+FLANGE Reverb and flanger in parallel
RevFlange REVFLANGE Reverb and flanger in series
Rev+Sympho. REV+SYMPHO. Reverb and symphonic in parallel
RevSympho. REVSYMPHO. Reverb and symphonic in series
RevPan REVPAN Reverb and auto-pan in series
Delay+Er. DELAY+ER. Delay and early reflections in parallel
DelayEr
. DE
LAYER. Delay and early reflections in series
Data List
8
Effects Parameters
REV-X HALL, REV-X ROOM, REV-X PLATE
Newly-developed two input, two output reverb algorithm. Delivers dense and rich
reverberation, smooth decay, and provides a spaciousness and depth that enhances the
original sound. Choose from three types depending on your location and needs: REV-X
HALL, REV-X ROOM, and REV-X PLATE.
REVERB HALL, REVERB ROOM, REVERB STAGE, REVERB PLATE
One input, two output hall, room, stage, and plate reverb simulations, all with gates.
Delay+Rev DELAY+REV Delay and reverb in parallel
DelayRev DELAYREV Delay and reverb in series
DistDelay DISTDELAY Distortion and delay in series
Multi Filter MULTI FILTER 3-band parallel filter (24 dB/octave)
Freeze FREEZE Simple sampler
Distortion DISTORTION Distortion
Amp Simulate AMP SIMULATE Guitar amp simulation
Comp276 COMP276
This compressor emulates the characteristics of an analog compressor that has
become a sought-after classic in recording studios.
Comp276S COMP276S This is a stereo model of COMP276.
Comp260 COMP260
This compressor emulates the characteristics of a compressor/limiter of the latter
1970s that has become a sought-after classic for live SR.
Comp260S COMP260S This is a stereo model of the COMP260.
Equalizer601 EQUALIZER601
This equalizer emulates the characteristics of an analog equalizer of the 1970s. It
can be used to obtain a sense of drive.
OpenDeck OPENDECK
This is a tape saturation effect that emulates the tape compression produced by
two open-reel tape recorders: a recording deck and a reproduction deck.
M.Band Dyna. M.BAND DYNA. Multi-band dynamics processor
M.Band Comp M.BAND COMP Multi-band compressor
Title Type Description
Parameter Range Description
REV TIME
0.28-27.94 s
*1
*1. These values are for when the effect type is REV-X HALL and the ROOM SIZE=28. The range will differ depending
on the effect type and ROOM SIZE setting.
Reverb time
INI. DLY 0.0-120.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
LO. RATIO 0.1-1.4 Low-frequency reverb time ratio
LO.FREQ 22.0 Hz-18.0 kHz Frequency point for LO.RATIO setting
DIFF. 0-10 Reverb diffusion (left-right reverb spread)
ROOM SIZE 0-28 Size of room
DECAY 0-53 Gate closing speed
HPF THRU, 22.0 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 1.00 kHz-18.0 kHz, THRU Low-pass filter cutoff frequency
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
LO. RATIO 0.1-2.4 Low-frequency reverb time ratio
DIFF. 0-10 Reverb diffusion (left-right reverb spread)
DENSITY 0-100% Reverb density
E/R DLY 0.0-100.0 ms Delay between early reflections and reverb
E/R BAL. 0-100%
Balance of early reflections and reverb
(0% = all reverb, 100% = all early reflections)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
GATE LVL OFF, -60 to 0 dB Level at which gate kicks in
ATTACK 0-120 ms Gate opening speed
HOLD
*1
*1. 0.02 ms-2.13 s (fs=44.1 kHz), 0.02 ms-1.96 s (fs=48 kHz)
Gate open time
DECAY
*2
*2. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Gate closing speed
Data List
9
STEREO REVERB
Two input, two output stereo reverb.
EARLY REF.
One input, two output early reflections.
GATE REVERB, REVERSE GATE
One input, two output early reflections with gate, and early reflections with reverse gate.
MONO DELAY
One input, one output basic repeat delay.
STEREO DELAY
Two input, two output basic stereo delay.
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
REV TYPE Hall, Room, Stage, Plate Reverb type
INI. DLY 0.0-100.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
LO. RATIO 0.1-2.4 Low-frequency reverb time ratio
DIFF. 0-10 Reverb diffusion (left-right reverb spread)
DENSITY 0-100% Reverb density
E/R BAL. 0-100%
Balance of early reflections and reverb
(0% = all reverb, 100% = all early reflections)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
Parameter Range Description
TYPE
S-Hall, L-Hall, Random,
Revers, Plate, Spring
Type of early reflection simulation
ROOMSIZE 0.1-20.0 Reflection spacing
LIVENESS 0-10 Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
DIFF. 0-10 Reflection diffusion (left-right reflection spread)
DENSITY 0-100% Reflection density
ER NUM. 1-19 Number of early reflections
FB GAIN -99 to +99% Feedback gain
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
Parameter Range Description
TYPE Type-A, Type-B Type of early reflection simulation
ROOMSIZE 0.1-20.0 Reflection spacing
LIVENESS 0-10 Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
DIFF. 0-10 Reflection diffusion (left-right reflection spread)
DENSITY 0-100% Reflection density
HI. RATIO 0.1-1.0 High-frequency feedback ratio
ER NUM. 1-19 Number of early reflections
FB GAIN -99 to +99% Feedback gain
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
Parameter Range Description
DELAY 0.0-2730.0 ms Delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1. (Maximum value depends on the tempo
setting)
Used in conjunction with TEMPO to determine DELAY
Parameter Range Description
DELAY L 0.0-1350.0 ms Left channel delay time
DELAY R 0.0-1350.0 ms Right channel delay time
FB. G L -99 to +99%
Left channel feedback (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
FB. G R -99 to +99%
Right channel feedback (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
Data List
10
MOD. DELAY
One input, two output basic repeat delay with modulation.
DELAY LCR
One input, two output 3-tap delay (left, center, right).
ECHO
Two input, two output stereo delay with crossed feedback loop.
CHORUS
Two input, two output chorus effect.
Parameter Range Description
DELAY 0.0-2725.0 ms Delay time
FB. GAIN -99 to +99% Feedback gain
HI. RATIO 0.1-1.0 High-frequency feedback ratio
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
WAVE Sine/Tri Modulation waveform
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
DLY.NOTE
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine DELAY
MOD.NOTE
*2
*2.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
DELAY L 0.0-2730.0 ms Left channel delay time
DELAY C 0.0-2730.0 ms Center channel delay time
DELAY R 0.0-2730.0 ms Right channel delay time
FB. DLY 0.0-2730.0 ms Feedback delay time
LEVEL L -100 to +100% Left channel delay level
LEVEL C -100 to +100% Center channel delay level
LEVEL R -100 to +100% Right channel delay level
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE C
*1
Used in conjunction with TEMPO to determine center channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FB
*1
Used in conjunction with TEMPO to determine feedback DELAY
Parameter Range Description
DELAY L 0.0-1350.0 ms Left channel delay time
DELAY R 0.0-1350.0 ms Right channel delay time
FB.DLY L 0.0-1350.0 ms Left channel feedback delay time
FB.DLY R 0.0-1350.0 ms Right channel feedback delay time
FB. G L -99 to +99%
Left channel feedback gain (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
FB. G R -99 to +99%
Right channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
LR FBG -99 to +99%
Left to right channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
RL FBG -99 to +99%
Right to left channel feedback gain (plus values for normal-phase feedback,
minus values for reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FBL
*1
Used in conjunction with TEMPO to determine left channel feedback
DELAY
NOTE FBR
*1
Used in conjunction with TEMPO to determine right channel feedback
DELAY
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
AM DEPTH 0-100% Amplitude modulation depth
PM DEPTH 0-100% Pitch modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain
Data List
11
FLANGE
Two input, two output flange effect.
SYMPHONIC
Two input, two output symphonic effect.
PHASER
Two input, two output 16-stage phaser.
DYNA.FLANGE
Two input, two output dynamically controlled flanger.
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
OFFSET 0-100 Lowest phase-shifted frequency offset
PHASE 0.00-354.38 degrees Left and right modulation phase balance
STAGE 2, 4, 6, 8, 10, 12, 14, 16 Number of phase shift stages
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain
Parameter Range Description
SOURCE INPUT, MIDI Control source: input signal or MIDI Note On velocity
SENSE 0-100 Sensitivity
DIR. UP, DOWN Upward or downward frequency change
DECAY
*1
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Decay speed
OFFSET 0-100 Delay time offset
FB.GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain
Data List
12
DYNA.PHASER
Two input, two output dynamically controlled phaser.
HQ.PITCH
One input, two output high-quality pitch shifter.
DUAL PITCH
Two input, two output pitch shifter.
TREMOLO
Two input, two output tremolo effect.
Parameter Range Description
SOURCE INPUT, MIDI
Control source:
input signal or MIDI Note On velocity
SENSE 0-100 Sensitivity
DIR. UP, DOWN Upward or downward frequency change
DECAY
*1
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Decay speed
OFFSET 0-100 Lowest phase-shifted frequency offset
FB.GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
STAGE 2, 4, 6, 8, 10, 12, 14, 16 Number of phase shift stages
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain
Parameter Range Description
PITCH -12 to +12 semitones Pitch shift
FINE -50 to +50 cents Pitch shift fine
DELAY 0.0-1000.0 ms Delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
MODE 1-10 Pitch shift precision
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine DELAY
Parameter Range Description
PITCH 1 -24 to +24 semitones Channel #1 pitch shift
FINE 1 -50 to +50 cents Channel #1 pitch shift fine
LEVEL 1 -100 to +100%
Channel #1 level (plus values for normal phase, minus values for reverse
phase)
PAN 1 L63 to R63 Channel #1 pan
DELAY 1 0.0-1000.0 ms Channel #1 delay time
FB. G 1 -99 to +99%
Channel #1 feedback gain (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
MODE 1-10 Pitch shift precision
PITCH 2 -24 to +24 semitones Channel #2 pitch shift
FINE 2 -50 to +50 cents Channel #2 pitch shift fine
LEVEL 2 -100 to +100%
Channel #2 level (plus values for normal phase, minus values for reverse
phase)
PAN 2 L63 to R63 Channel #2 pan
DELAY 2 0.0-1000.0 ms Channel #2 delay time
FB. G 2 -99 to +99%
Channel #2 feedback gain (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
SYNC OFF/ON Tempo parameter sync on/off
NOTE 1
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine Channel #1 delay
NOTE 2
*1
Used in conjunction with TEMPO to determine Channel #2 delay
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
WAVE Sine, Tri, Square Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain
Data List
13
AUTOPAN
Two input, two output autopanner.
ROTARY
One input, two output rotary speaker simulator.
RING MOD.
Two input, two output ring modulator.
MOD.FILTER
Two input, two output modulation filter.
DYNA.FILTER
Two input, two output dynamically controlled filter.
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
DIR.
*1
*1. LR, LR, LR , Tu rn L, Tur n R
Panning direction
WAVE Sine, Tri, Square Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*2
*2.
Used in conjunction with TEMPO to determine FREQ
LSH F 21.2 Hz-8.00 kHz Low shelving filter frequency
LSH G -12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz-16.0 kHz High shelving filter frequency
HSH G -12.0 to +12.0 dB High shelving filter gain
Parameter Range Description
ROTATE STOP, START Rotation stop, start
SPEED SLOW, FAST
Rotation speed
(see SLOW and FAST parameters)
SLOW 0.05-10.00 Hz SLOW rotation speed
FAST 0.05-10.00 Hz FAST rotation speed
DRIVE 0-100 Overdrive level
ACCEL 0-10 Acceleration at speed changes
LOW 0-100 Low-frequency filter
HIGH 0-100 High-frequency filter
Parameter Range Description
SOURCE OSC, SELF Modulation source: oscillator or input signal
OSC FREQ 0.0-5000.0 Hz Oscillator frequency
FM FREQ. 0.05-40.00 Hz Oscillator frequency modulation speed
FM DEPTH 0-100% Oscillator frequency modulation depth
SYNC OFF/ON Tempo parameter sync on/off
FM NOTE
*1
*1.
Used in conjunction with TEMPO to determine FM FREQ
Parameter Range Description
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
PHASE 0.00-354.38 degrees Left-channel modulation and right-channel modulation phase difference
TYPE LPF, HPF, BPF Filter type: low pass, high pass, band pass
OFFSET 0-100 Filter frequency offset
RESO. 0-20 Filter resonance
LEVEL 0-100 Output level
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
SOURCE INPUT, MIDI
Control source:
input signal or MIDI Note On velocity
SENSE 0-100 Sensitivity
DIR. UP, DOWN Upward or downward frequency change
DECAY
*1
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Filter frequency change decay speed
TYPE LPF, HPF, BPF Filter type: low pass, high pass, band pass
OFFSET 0-100 Filter frequency offset
RESO. 0-20 Filter resonance
LEVEL 0-100 Output level
Data List
14
REV+CHORUS
One input, two output reverb and chorus effects in parallel.
REVCHORUS
One input, two output reverb and chorus effects in series.
REV+FLANGE
One input, two output reverb and flanger effects in parallel.
REVFLANGE
One input, two output reverb and flanger effects in series.
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV/CHO 0-100%
Reverb and chorus balance
(0% = all reverb, 100% = all chorus)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
AM DEPTH 0-100% Amplitude modulation depth
PM DEPTH 0-100% Pitch modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV.BAL 0-100%
Reverb and chorused reverb balance
(0% = all chorused reverb, 100% = all reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
AM DEPTH 0-100% Amplitude modulation depth
PM DEPTH 0-100% Pitch modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV/FLG 0-100%
Reverb and flange balance
(0% = all reverb, 100% = all flange)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV.BAL 0-100%
Reverb and flanged reverb balance
(0% = all flanged reverb, 100% = all reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Data List
15
REV+SYMPHO.
One input, two output reverb and symphonic effects in parallel.
REVSYMPHO.
One input, two output reverb and symphonic effects in series.
REVPAN
This is a 1-in/2-out series-connected reverb and auto-pan effect.
DELAY+ER.
One input, two output delay and early reflections effects in parallel.
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV/SYM 0-100%
Reverb and symphonic balance
(0% = all reverb, 100% = all symphonic)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV.BAL 0-100%
Reverb and symphonic reverb balance
(0% = all symphonic reverb, 100% = all reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
MOD. DLY 0.0-500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*1
*1.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
HI. RATIO 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
REV.BAL 0-100%
Reverb and panned reverb balance (0% = all panned reverb, 100% = all
reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
DIR.
*1
*1. LR, LR, LR, Turn L, Turn R
Panning direction
WAVE Sine, Tri, Square Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
NOTE
*2
*2.
Used in conjunction with TEMPO to determine FREQ
Parameter Range Description
DELAY L 0.0-1000.0 ms Left channel delay time
DELAY R 0.0-1000.0 ms Right channel delay time
FB. DLY 0.0-1000.0 ms Feedback delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
DLY/ER 0-100%
Delay and early reflections balance (0% = all delay, 100% = all early
reflections)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
TYPE
S-Hall, L-Hall, Random,
Revers, Plate, Spring
Type of early reflection simulation
ROOMSIZE 0.1-20.0 Reflection spacing
LIVENESS 0-10 Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reflection density
ER NUM. 1-19 Number of early reflections
SYNC OFF/ON
Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FB
*1
Used in conjunction with TEMPO to determine feedback DELAY
Data List
16
DELAYER.
One input, two output delay and early reflections effects in series.
DELAY+REV
One input, two output delay and reverb effects in parallel.
DELAYREV
One input, two output delay and reverb effects in series.
Parameter Range Description
DELAY L 0.0-1000.0 ms Left channel delay time
DELAY R 0.0-1000.0 ms Right channel delay time
FB. DLY 0.0-1000.0 ms Feedback delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
DLY.BAL 0-100%
Delay and early reflected delay balance
(0% = all early reflected delay, 100% = all delay)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
TYPE
S-Hall, L-Hall, Random,
Revers, Plate, Spring
Type of early reflection simulation
ROOMSIZE 0.1-20.0 Reflection spacing
LIVENESS 0-10 Early reflections decay characteristics (0 = dead, 10 = live)
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reflection density
ER NUM. 1-19 Number of early reflections
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FB
*1
Used in conjunction with TEMPO to determine feedback DELAY
Parameter Range Description
DELAY L 0.0-1000.0 ms Left channel delay time
DELAY R 0.0-1000.0 ms Right channel delay time
FB. DLY 0.0-1000.0 ms Feedback delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
DELAY HI 0.1-1.0 High-frequency feedback ratio
DLY/REV 0-100%
Delay and reverb balance
(0% = all delay, 100% = all reverb)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
REV HI 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FB
*1
Used in conjunction with TEMPO to determine feedback DELAY
*1. (Maximum value depends on the tempo setting)
Parameter Range Description
DELAY L 0.0-1000.0 ms Left channel delay time
DELAY R 0.0-1000.0 ms Right channel delay time
FB. DLY 0.0-1000.0 ms Feedback delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
DELAY HI 0.1-1.0 High-frequency feedback ratio
DLY.BAL 0-100%
Delay and delayed reverb balance
(0% = all delayed reverb, 100% = all delay)
HPF THRU, 21.2 Hz-8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz-16.0 kHz, THRU Low-pass filter cutoff frequency
REV TIME 0.3-99.0 s Reverb time
INI. DLY 0.0-500.0 ms Initial delay before reverb begins
REV HI 0.1-1.0 High-frequency reverb time ratio
DIFF. 0-10 Diffusion (spread)
DENSITY 0-100% Reverb density
SYNC OFF/ON Tempo parameter sync on/off
NOTE L
*1
*1. (Maximum value depends on the tempo setting)
Used in conjunction with TEMPO to determine left channel DELAY
NOTE R
*1
Used in conjunction with TEMPO to determine right channel DELAY
NOTE FB
*1
Used in conjunction with TEMPO to determine feedback DELAY
Parameter Range Description
Data List
17
DISTDELAY
One input, two output distortion and delay effects in series.
MULTI FILTER
Two input, two output 3-band multi-filter (24 dB/octave).
FREEZE
One input, two output basic sampler.
DISTORTION
One input, two output distortion effect.
Parameter Range Description
DST TYPE
DST1, DST2, OVD1,
OVD2, CRUNCH
Distortion type (DST = distortion, OVD = overdrive)
DRIVE 0-100 Distortion drive
MASTER 0-100 Master volume
TONE -10 to +10 Tone control
N. GATE 0-20 Noise reduction
SYNC OFF/ON Tempo parameter sync on/off
DLY.NOTE
*1
*1. (Maximum value depends on the tempo
setting)
Used in conjunction with TEMPO to determine DELAY
MOD.NOTE
*2
*2.
Used in conjunction with TEMPO to determine FREQ
DELAY 0.0-2725.0 ms Delay time
FB. GAIN -99 to +99%
Feedback gain (plus values for normal-phase feedback, minus values for
reverse-phase feedback)
HI. RATIO 0.1-1.0 High-frequency feedback ratio
FREQ. 0.05-40.00 Hz Modulation speed
DEPTH 0-100% Modulation depth
DLY.BAL 0-100%
Distortion and delay balance
(0% = all distortion, 100% = all delayed distortion)
Parameter Range Description
TYPE 1 LPF, HPF, BPF Filter 1 type: high pass, low pass, band pass
FREQ. 1 28.0 Hz-16.0 kHz Filter 1 frequency
LEVEL 1 0-100 Filter 1 level
RESO. 1 0-20 Filter 1 resonance
TYPE 2 LPF, HPF, BPF Filter 2 type: high pass, low pass, band pass
FREQ. 2 28.0 Hz-16.0 kHz Filter 2 frequency
LEVEL 2 0-100 Filter 2 level
RESO. 2 0-20 Filter 2 resonance
TYPE 3 LPF, HPF, BPF Filter 3 type: high pass, low pass, band pass
FREQ. 3 28.0 Hz-16.0 kHz Filter 3 frequency
LEVEL 3 0-100 Filter 3 level
RESO. 3 0-20 Filter 3 resonance
Parameter Range Description
REC MODE MANUAL, INPUT
In MANUAL mode, recording is started by pressing the REC and PLAY
buttons. In INPUT mode, Record-Ready mode is engaged by pressing the
REC button, and actual recording is triggered by the input signal.
REC DLY -1000 to +1000 ms
Recording delay.
For plus values, recording starts after the trigger is received. For minus
values, recording starts before the trigger is received.
PLY MODE
MOMENT, CONTI.,
INPUT
In MOMENT mode, the sample plays only while the PLAY button is
pressed. In CONT mode, playback continues once the PLAY button has
been pressed. The number of times the sample plays is set using the LOOP
NUM parameter. In INPUT mode, playback is triggered by the input signal.
TRG LVL -60 to 0 dB
Input trigger level (i.e., the signal level required to trigger recording or
playback)
TRG MASK 0-1000 ms
Once playback has been triggered, subsequent triggers are ignored for the
duration of the TRG MASK time.
START
*1
*1. 0.0-5941.0 ms (fs=44.1 kHz), 0.0 ms-5458.3 ms (fs=48 kHz)
Playback start point in milliseconds
END
*1
Playback end point in milliseconds
LOOP
*1
Loop start point in milliseconds
LOOP
NUM
0-100 Number of times the sample plays
PITCH -12 to +12 semitones Playback pitch shift
FINE -50 to +50 cents Playback pitch shift fine
MIDI TRG OFF, C1-C6, ALL The PLAY button can be triggered by using MIDI Note on/off messages.
START
[SAMPLE]
0-131000 Playback start point in samples
END
[SAMPLE]
0-131000 Playback end point in samples
LOOP
[SAMPLE]
0-131000 Loop start point in samples
Parameter Range Description
DST TYPE
DST1, DST2, OVD1,
OVD2, CRUNCH
Distortion type (DST = distortion, OVD = overdrive)
DRIVE 0-100 Distortion drive
MASTER 0-100 Master volume
TONE -10 to +10 Tone control
N. GATE 0-20 Noise reduction
Data List
18
AMP SIMULATE
One input, two output guitar amp simulator.
COMP276
This effect emulates the characteristics of analog compressors that are widely used in
recording studios. It produces a thick, strong frame sound suitable for drums and bass. You
can control two monaural channels independently.
COMP276S
This effect emulates the characteristics of analog compressors that are widely used in
recording studios. It produces a thick, strong frame sound suitable for drums and bass. You
can link and control the L and R channel parameters.
COMP260
This effect emulates the characteristics of mid 70's compressors/limiters that are the standard
for live SR. You can control two monaural channels independently. You can also link several
parameters via stereo links.
COMP260S
This effect emulates the characteristics of mid 70's compressors/limiters that are the standard
for live SR. You can link and control the L and R channel parameters.
Parameter Range Description
AMP TYPE
*1
*1. STK-M1, STK-M2, THRASH, MIDBST, CMB-PG, CMB-VR, CMB-DX, CMB-TW, MINI, FLAT
Guitar amp simulation type
DST TYPE
DST1, DST2, OVD1,
OVD2, CRUNCH
Distortion type (DST = distortion, OVD = overdrive)
DRIVE 0-100 Distortion drive
MASTER 0-100 Master volume
BASS 0-100 Bass tone control
MIDDLE 0-100 Middle tone control
TREBLE 0-100 High tone control
N. GATE 0-20 Noise reduction
CAB DEP 0-100% Speaker cabinet simulation depth
EQ F 100 Hz-8.00 kHz EQ (peaking type) frequency
EQ G -12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0-0.10 EQ (peaking type) bandwidth
Parameter Range Description
INPUT 1 -180 to 0 dB Adjusts the CH1 input level
OUTPUT 1 -180 to 0 dB Adjusts the CH1 output gain
RATIO 1 2:1, 4:1, 8:1, 12:1, 20:1 Ratio for CH1 compressor
ATTACK 1 0.022-50.4 ms Attack time of CH1 compressor
RELEASE1 10.88-544.22 ms Release time of CH1 compressor
MAKE UP1 OFF, ON
Automatically corrects output gain reduction when CH1 compressor is
applied
SIDEHPF1 OFF, ON
When the HPF in the side chain of the CH1 compressor is turned on, the
compression applied to the low range will be weakened, thus emphasizing
the low range.
INPUT 2 -180 to 0 dB Adjusts the CH2 input level
OUTPUT 2 -180 to 0 dB Adjusts the CH2 output gain
RATIO 2 2:1, 4:1, 8:1, 12:1, 20:1 Ratio of CH2 compressor
ATTACK 2 0.022-50.4 ms Attack time of CH2 compressor
RELEASE2 10.88-544.22 ms Release time of CH2 compressor
MAKE UP2 OFF, ON
Automatically corrects output gain reduction when the CH2 compressor is
applied
SIDEHPF2 OFF, ON
When the HPF in the side chain of the CH2 compressor is turned on, the
compression applied to the low range will be weakened, thus emphasizing
the low range.
Parameter Range Description
INPUT -180 to 0 dB Adjusts the input level
OUTPUT -180 to 0 dB Adjusts the output gain
RATIO 1:2, 4:1, 8:1, 12:1, 20:1 Ratio of the compressor
ATTACK 0.022-50.4 ms Attack time of the compressor
RELEASE 10.88-544.22 ms Release time of the compressor
MAKE UP OFF, ON
Automatically corrects output gain reduction when the compressor is
applied
SIDE HPF OFF, ON
When the HPF in the side chain of the compressor is turned on, the
compression applied to the low range will be weakened, thus emphasizing
the low range.
Parameter Range Description
THRE.1 -60 to 0.0 dB Threshold of CH compressor
KNEE1 SOFT, MEDIUM, HARD Knee of CH1 compressor
ATTACK1 0.01-80.0 ms Attack time of CH1 compressor
RELEASE1 6.2-999 ms Release time of CH1 compressor
RATIO1 1.0-500, ∞ Ratio for CH1 compressor
OUTPUT1 -20 to 40 dB Adjusts the CH1 output gain
THRE.2 -60 to 0.0 dB Threshold of CH2 compressor
KNEE2 SOFT, MEDIUM, HARD Knee of CH2 compressor
ATTACK2 0.01-80.0 ms Attack time of CH2 compressor
RELEASE2 6.2-999 ms Release time of CH2 compressor
RATIO2 1.0-500, ∞ Ratio of CH2 compressor
OUTPUT2 -20 to 40 dB Adjusts the CH2 output gain
ST LINK OFF, ON
Links CH1 and CH2 as a stereo pair. THRE., KNEE, ATTACK, RELEASE, and
RATIO parameters are linked; OUTPUT parameter is not linked
Parameter Range Description
THRE. -60 to 0.0 dB Threshold of the compressor
KNEE SOFT, MEDIUM, HARD Knee of the compressor
ATTACK 0.01-80.0 ms Attack time of the compressor
RELEASE 6.2-999 ms Release time of the compressor
RATIO 1.0-500, ∞ Ratio of the compressor
OUTPUT -20 to 40 dB Adjusts the output gain
Data List
19
EQUALIZER601
This effect emulates the characteristics of 70's analog equalizers. Re-creating the distortion
of typical analog circuits will add drive to the sound.
OPENDECK
It emulates the tape compression created by two open reel tape recorders (a recording deck
and a playback deck). You can change the sound quality by adjusting various elements, such
as the deck type, tape quality, playback speed, etc.
M.BAND DYNA.
Two input, two output 3-band dynamically controlled processor, with individual solo and gain
reduction metering for each band.
Parameter Range Description
LO TYPE HPF-2/1, LSH-1/2 Type of EQ1
LO F 16.0 Hz to 20.0 kHz Cut-off frequency of EQ1
LO G -18.0 to +18.0 dB Gain of EQ1
MID1 Q 0.50-16.0 Q of EQ2
MID1 F 16.0 Hz to 20.0 kHz Center frequency of EQ2
MID1 G -18.0 to +18.0 dB Gain of EQ2
MID2 Q 0.50-16.0 Q of EQ3
MID2 F 16.0 Hz to 20.0 kHz Center frequency of EQ3
MID2 G -18.0 to +18.0 dB Gain of EQ3
INPUT -18.0 to +18.0 dB Input gain
OUTPUT -18.0 to +18.0 dB Output gain
MID3 Q 0.50-16.0 Q of EQ4
MID3 F 16.0 Hz to 20.0 kHz Center frequency of EQ4
MID3 G -18.0 to +18.0 dB Gain of EQ4
MID4 Q 0.50-16.0 Q of EQ5
MID4 F 16.0 Hz to 20.0 kHz Center frequency of EQ5
MID4 G -18.0 to +18.0 dB Gain of EQ5
HI TYPE LPF-2/1, HSH-1/2 Type of EQ6
HI F
16.0 Hz to 20.0 kHz
*1
*1. 16.0 Hz to 20.0 kHz (LPF-1, LPF-2), 1.0 kHz to 20.0 kHz (HSH-1, HSH-2)
Cut-off frequency of EQ6
HI G -18.0 to +18.0 dB Gain of EQ6
LO SW OFF, ON Switches EQ1 on/off
MID1 SW OFF, ON Switches EQ2 on/off
MID2 SW OFF, ON Switches EQ3 on/off
MID3 SW OFF, ON Switches EQ4 on/off
MID4 SW OFF, ON Switches EQ5 on/off
HI SW OFF, ON Switches EQ6 on/off
TYPE CLEAN, DRIVE
Selects the equalizer type.
The CLEAN equalizer provides non-distorted, clear, typical digital sound,
emulating variations in frequency response in the analog circuits. The
DRIVE equalizer provides distorted, driven sound that enhances analog
flavor, emulating changes in frequency response in the analog circuits.
Parameter Range Description
REC DEC
Swss70, Swss78, Swss85,
Amer70
Selects the recording deck type
REC LVL -96.0 to +18.0 dB
Adjusts the input level of the recording deck. As you raise the level, tape
compression is generated, which narrows the dynamic range and distorts
the sound.
REC HI -6.0 to +6.0 dB Adjusts the high range gain of the recording deck
REC BIAS -1.00 to +1.00 Adjusts the bias of the recording deck
REPR DEC
Swss70, Swss78, Swss85,
Amer70
Selects the playback deck type
REPR LVL -96.0 to +18.0 dB Adjusts the output level of the playback deck
REPR HI -6.0 to +6.0 dB Adjusts the high range gain of the playback deck
REPR LO -6.0 to +6.0 dB Adjusts the low range gain of the playback deck
MAKE UP Off, On
When you adjust the REC LVL, the REPR LVL reflects the change,
maintaining the relative output level. You can change the amount of
distortion without changing the output level.
TP SPEED 15ips, 30ips Selects the tape speed
TP KIND Old, New Selects the tape type
Parameter Range Description
L-M XOVER 21.2 Hz-8.00 kHz Crossover frequency between the low and mid bands
M-H XOVER 21.2 Hz-8.00 kHz Crossover frequency between the mid and high bands
SLOPE -6 dB, -12 dB Filter slope
LOW GAIN -12.0 dB to +12.0 dB Low band gain
MID GAIN -12.0 dB to +12.0 dB Mid band gain
HI. GAIN -12.0 dB to +12.0 dB High band gain
TOTAL -72.0 dB to +12.0 dB Overall gain
CEILING -6.0 dB to 0.0 dB, OFF Restricts the output so that it will not exceed the specified level
CMP.THRE -24.0 dB to 0.0 dB Threshold of the compressor
CMP.RAT 1:1 to 20:1 Ratio of the compressor
CMP.ATK 0-120 ms Attack time of the compressor
CMP.REL
*1
Release time of the compressor
CMP.KNEE 0-5 Knee of the compressor
CMP.BYP OFF/ON Bypasses the compressor
EXP.THRE -54.0 dB to -24.0 dB Threshold of the expander
EXP.RAT 1:1 to 5:1 Ratio of the expander
EXP.REL
*1
Release time of the expander
EXP.BYP OFF/ON Bypasses the expander
LIM.THRE -12.0 dB to 0.0 dB Threshold of the limiter
Data List
20
M.BAND COMP
Two input, two output 3-band compressor, with individual solo and gain reduction metering for
each band.
Premium Rack Processor Parameters
Portico5033
This models an analog 5-band EQ made by the RND company.
Portico5043
This models an analog compressor/limiter made by the RND company.
LIM.ATK 0-120 ms Attack time of the limiter
LIM.REL
*1
Release time of the limiter
LIM.KNEE 0-5 Knee of the limiter
LIM.BYP OFF/ON Bypasses the limiter
PRESENCE -10 to +10
Positive (+) values lower the threshold of the high band and raise the
threshold of the low band. Negative (-) values do the opposite. If this is
set to 0, the high, mid, and low bands will be affected in the same way.
LOOKUP 0.0-100.0 ms Lookup delay
MAKE UP OFF/ON Automatically adjusts the output level
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Parameter Range Description
L-M XOVER 21.2 Hz-8.00 kHz Crossover frequency between the low and mid bands
M-H XOVER 21.2 Hz-8.00 kHz Crossover frequency between the mid and high bands
SLOPE -6 dB, -12 dB Filter slope
LOW GAIN -12.0 dB to +12.0 dB Low band gain
MID GAIN -12.0 dB to +12.0 dB Mid band gain
HI. GAIN -12.0 dB to +12.0 dB High band gain
TOTAL -72.0 dB to +12.0 dB Overall gain
CEILING -6.0 dB to 0.0 dB, OFF Restricts the output so that it will not exceed the specified level
LOW THRE -54.0 dB to 0.0 dB Threshold of the low band compressor
LOW RAT 1:1 to 20:1 Ratio of the low band compressor
LOW ATK 0-120 ms Attack time of the low band compressor
LOW REL
*1
*1. 6.0 ms-46.0 s (fs=44.1 kHz), 5.0 ms-42.3 s (fs=48 kHz)
Release time of the low band compressor
LOW KNEE 0-5 Knee of the low band compressor
LOW BYP OFF/ON Bypasses the low band compressor
MID THRE -54.0 dB to 0.0 dB Threshold of the mid band compressor
MID RAT 1:1 to 20:1 Ratio of the mid band compressor
MID ATK 0-120 ms Attack time of the mid band compressor
MID REL
*1
Release time of the mid band compressor
MID KNEE 0-5 Knee of the mid band compressor
MID BYP OFF/ON Bypasses the mid band compressor
HI. THRE -54.0 dB to 0.0 dB Threshold of the high band compressor
HI. RAT 1:1 to 20:1 Ratio of the high band compressor
HI. ATK 0-120 ms Attack time of the high band compressor
HI. RAT
*1
Release time of the high band compressor
HI. KNEE 0-5 Knee of the high band compressor
HI. BYP OFF/ON Bypasses the high band compressor
LOOKUP 0.0-100.0 ms Lookup delay
MAKE UP OFF/ON Automatically adjusts the output level
Parameter Range Description
Parameter Range Description
ALL BYPASS OFF, ON
Turns bypass on/off for the EQ. Even in the bypassed state, the signal will
pass through the input/output transformers and the amp circuit.
TRIM -12.0 to 12.0 dB Input gain
LF FREQ 30.00 to 300.0 Hz Center frequency of the LF band
LF GAIN -12.0 to 12.0 dB Gain of the LF band
LMF IN OFF, ON Switches the LMF band on/off
LMF Q 0.70 to 5.00 Q of the LMF band
LMF FREQ 50.00 to 400.0 Hz Center frequency of the LMF band
LMF GAIN -12.0 to 12.0 dB Gain of the LMF band
MF IN OFF, ON Switches the MF band on/off
MF Q 0.70 to 5.00 Q of the MF band
MF FREQ 330.0 to 2500 Hz Center frequency of the MF band
MF GAIN -12.0 to 12.0 dB Gain of the MF band
HMF IN OFF, ON Switches the HMF band on/off
HMF Q 0.70 to 5.00 Q of the HMF band
HMF FREQ 1.80k to 16.0k Hz Center frequency of the HMF band
HMF GAIN -12.0 to 12.0 dB Gain of the HMF band
LF/HF IN OFF, ON Switches the LF/HF bands on/off
HF FREQ 2.50k to 25.0k Hz Center frequency of the HF band
HF GAIN -12.0 to 12.0 dB Gain of the HF band
Parameter Range Description
IN OFF, ON
Turns bypass on/off for the compressor. When bypassed, the button will
be unlit. However even in the bypassed state, the signal will pass through
the input/output transformers and the amp circuit.
FB OFF, ON Switches between feed-forward type and feed-back type
THRESHOLD -50.0 to 0.0 dB Threshold level
RATIO 1.10 : 1 to 28.9 : 1, LIMIT Compression ratio
ATTACK 20 to 75 ms Attack time
RELEASE 100 ms to 2.50 sec Release time
GAIN -6.0 to 20.0 dB Output level
Data List
21
Portico 5045
This models the Primary Source Enhancer made by Rupert Neve Designs.
U76
This models a well-known vintage compressor/limiter used in a wide range of situations.
Opt-2A
This processor emulates a well-known vintage model of vacuum tube opto compressor.
EQ-1A
This processor emulates a vintage EQ that's considered a classic example of a passive EQ.
Dynamic EQ
This is a newly developed equalizer that dynamically changes the EQ gain in response to the
input signal, controlling the amount of EQ cut or boost in a way similar to a compressor or
expander.
Parameter Range Description
PROCESS ENGAGE OFF, ON
Turns the enhancement circuit on/off. Even when this is off, the signal
passes through the audio transformer and discrete amp circuit.
RMS/Peak RMS, Peak Operation mode of the level detector.
TIME CONSTANT A, B, C, D, E, F Attack and release time.
THRESHOLD -42.0 to -12.0 dB Threshold level.
DEPTH 0.0 to -20.0 dB Amount of attenuation for signals below the threshold level.
Parameter Range Description
INPUT -96.0 to 0.0 dB Input level
OUTPUT -96.0 to 0.0 dB Output level
ATTACK 5.50 to 0.10 ms
Attack time of the compressor. Turning this all the way to the right
produces the fastest attack.
RELEASE 1100.0 to 56.4 ms
Release time of the compressor. Turning this all the way to the right
produces the fastest release.
RATIO ALL, 4, 8, 12, 20
Switches the compression ratio. Pressing ALL produces the strongest
effect.
METER OFF, +4, +8, GR Switches the meter display
Parameter Range Description
GAIN -56.0 dB to 40.0 dB Output level
PEAK REDUCTION -48.0 dB to 48.0 dB Amount of gain reduction
RATIO 2.00 to 10.00 Compression ratio
METER SELECT
OUTPUT+10,
GAIN REDUCTION,
OUTPUT+4
Switches the meter display
Parameter Range Description
LOW FREQUENCY 20, 30, 60, 100 Hz Frequency range of the low range filter
(LOW) BOOST 0.0 to 10.0 Boost amount of the low range filter
(LOW) ATTEN 0.0 to 10.0 Attenuation amount of the low range filter
HIGH FREQUENCY 3k, 4k, 5k, 8k, 10k, 12k, 16k Hz Frequency range of the high range filter
(HIGH) BOOST 0.0 to 10.0 Boost amount of the high range filter
(HIGH) BAND WIDTH 0.0 to 10.0 Band width of the high range filter
(HIGH) ATTEN SEL 5k, 10k, 20k Hz Frequency range attenuated by the high range filter
(HIGH) ATTEN 0.0 to 10.0 Attenuation amount of the high range filter
IN OFF, ON
Turns the processor on/off. If this is off, the filter section
will be bypassed, but the signal will pass through the
input/output transformers and the amp circuit.
Parameter Range Description
BAND ON/OFF OFF, ON Turns the corresponding band on/off
SIDECHAIN CUE OFF, ON
If this is on, the sidechain signal that controls the dynamics will
be sent to the CUE bus for monitoring.
SIDECHAIN LISTEN OFF, ON
If this is on, the sidechain signal that is linked to the dynamics
will be output to the bus (such as the STEREO bus or a MIX/
MATRIX bus) to which the inserted channel is being sent.
FILTER TYPE Low Shelf, Bell, Hi Shelf Switches the type of equalizer and sidechain filter
FREQUENCY 20.0 to 20.0k Hz Frequency controlled by the equalizer and sidechain filter
Q 15.0 to 0.50 Q of the equalizer and sidechain filter
THRESHOLD -80.0 to 10.0 dB Threshold value at which processing begins to apply
RATIO ∞ : 1 to 1 : 1.50 Sets the boost/cut ratio relative to the input signal
MODE BELOW, ABOVE
Specifies whether the processor will operate when the
sidechain signal exceeds the threshold setting (ABOVE) or
when it falls below the threshold setting (BELOW)
ATTACK/RELEASE FAST, SLOW, AUTO
Attack time/release time for when compression or boost is
applied
Data List
22
Buss Comp 369
MBC4
Parameter Range Description
INPUT ADJUST -15.0 to +15.0dB
Input gain. However, the output gain is also linked so that there
is no change in the pass-through volume. For example, if
INPUT ADJUST is +5dB, the input gain is +5dB and the output
gain is -5dB.
LINK ON, OFF Stereo link function (STEREO only)
METER IN, GR, OUT Meter switch (STEREO only)
VU IN, OUT Meter switch (DUAL only)
COMP IN ON, OFF Compressor on/off
COMP RATIO 1.5:1, 2:1, 3:1, 4:1, 6:1 Ratio of the compressor
COMP GAIN 0.0 to +20.0dB Compressor gain
COMP RECOVERY
100ms, 400ms, 800ms,
1500ms, a1, a2
Compressor release. The release times for a1 (auto 1) and a2
(auto 2) change automatically. a1: Changes automatically
between 100 ms and 2 sec. a2: Changes automatically
between 50 ms and 5 sec.
COMP THRESHOLD -40 to -5dBFS Threshold of the compressor
LIMIT IN ON, OFF Limiter on/off
LIMIT ATTACK FAST, SLOW Attack time of the limiter FAST: 2 ms, SLOW: 4 ms
LIMIT RECOVERY
50ms, 100ms, 200ms,
800ms, a1, a2
Limiter release. The release times for a1 (auto 1) and a2 (auto
2) change automatically. a1: Changes automatically between
100 ms and 2 sec. a2: Changes automatically between 50 ms
and 5 sec.
LIMIT THRESHOLD -16 to -5 dBFS Threshold of the limiter
Parameter Range Description
LOW CROSSOVER 20 to 500Hz Crossover frequency between the low and low mid bands
MID CROSSOVER 80 to 10kHz Crossover frequency between the low mid and high mid bands
HIGH CROSSOVER 1k to 15kHz
Crossover frequency between the low high mid and high
bands
LOW GAIN -18.0dB to 12.0dB Low band gain
LOW THRESHOLD -80.0dB to 0.0dB Threshold of low band
LOW RATIO 1.0:1 to 20.0:1 Ratio of low band
LOW ATTACK 0.1 to 120ms Attack time of low band
LOW RELEASE 5 to 1000ms Release time of low band
LOW COMP IN ON, OFF Switches the compressor of low band on/off
LOW CUE ON ON, OFF
If this is on, the low band signal will be sent to the CUE bus for
monitoring.
LOW MID GAIN -18.0dB to 12.0dB Low mid band gain
LOW MID
THRESHOLD
-80.0dB to 0.0dB Threshold of low mid band
LOW MID RATIO 1.0:1 to 20.0:1 Ratio of low mid band
LOW MID ATTACK 0.1ms to 120ms Attack time of low mid band
LOW MID RELEASE 5ms to 1000ms Release time of low mid band
LOW MID COMP IN ON, OFF Switches the compressor of low mid band on/off
LOW MID CUE ON ON, OFF
If this is on, the low mid band signal will be sent to the CUE bus
for monitoring.
HIGH MID GAIN -18.0dB to 12.0dB High mid band gain
HIGH MID
THRESHOLD
-80.0dB to 0.0dB Threshold of high mid band
HIGH MID RATIO 1.0:1 to 20.0:1 Ratio of high mid band
HIGH MID ATTACK 0.1ms to 120ms Attack time of high mid band
HIGH MID RELEASE 5ms to 1000ms Release time of high mid band
HIGH MID COMP IN ON, OFF Switches the compressor of high mid band on/off
HIGH MID CUE ON ON, OFF
If this is on, the high mid band signal will be sent to the CUE
bus for monitoring.
HIGH GAIN -18.0dB to 12.0dB High band gain
HIGH THRESHOLD -80.0dB to 0.0dB Threshold of high band
HIGH RATIO 1.0:1 to 20.0:1 Ratio of high band
HIGH ATTACK 0.1ms to 120ms Attack time of high band
HIGH RELEASE 5ms to 1000ms Release time of high band
HIGH COMP IN ON, OFF Switches the compressor of high band on/off
HIGH CUE ON ON, OFF
If this is on, the high band signal will be sent to the CUE bus for
monitoring.
MASTER GAIN -18.0dB to 12.0dB Master gain
KNEE HARD, 1, 2, 3, SOFT Knee of compressor
FLAVOUR VCA, OPTO Compressor type
HARMONICS ON, OFF Switches the harmonics on/off
LINK GAIN - Links and controls the gain of the four bands
LINK THRESHOLD - Links and controls the threshold of the four bands
LINK RATIO - Links and controls the ratio of the four bands
LINK ATTACK - Links and controls the attack time of the four bands
LINK RELEASE - Links and controls the release time of the four bands
Parameter Range Description
Data List
23
Automixer Parameters
Parameters That Can Be Assigned to Control Changes
Parameter Range Description
Group a, b, c Channel control field group
Override OFF, ON Turns on/off overriding of the channel control field
ChMode man, auto, mute Channel control field mode (man/auto/mute)
ChModePreset man, auto, mute Preset setting of the channel control field
Weight -100 to 15
Relative sensitivity among input channels in the channel
control field
MeterType gain, input, output Meter type of the master field
MasterOverride OFF, ON Turns on/off overriding of the master field
MasterMute OFF, ON Turns on/off the mute setting of the master field
Gain 0 to 127
Automixer gain displayed for each channel when the meter
button of the master field is set to “gain”
InputLevel 0 to 127
Input level displayed for each channel when the meter button
of the master field is set to “input”
OutputLevel 0 to 127
Output level displayed for each channel when the meter
button of the master field is set to “output”
PostWeightingFilter 0 to 127 Level indicator of the channel control field
Mode Parameter 1 Parameter 2
NO ASSIGN
BALANCE OUTPUT
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-STEREO R
CH ON
INPUT
CH 1-CH 72
*1
STIN1L-STIN8R
OUTPUT
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
CUE
OUTPUT
CUE MODE
SURROUND CUE MODE
FADER CUE RELEASE ON
INPUT CUE POINT
DCA CUE POINT
OUTPUT CUE POINT
DCA UNITY
OUTPUT LEVEL H
OUTPUT LEVEL L
ACTIVE CUE
CLEAR CUE
SPECIFIC CH
CH 1-CH 72
*1
STIN1L-STIN8R
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
DCA 1-DCA16
DCA
ON
DCA 1-DCA 16FADER H
FADER L
DIRECT OUT ON
CH 1-CH 72
*1
EFFECT
BYPASS
RACK1-8MIX BALANCE
PARAM 1 H - PARAM 32 L
FADER H
INPUT
CH 1-CH 72
*1
STIN1L-STIN8R
OUTPUT
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
FADER L
INPUT
CH 1-CH 72
*1
STIN1L-STIN8R
OUTPUT
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
GEQ
ON A
GEQ RACK1-GEQ RACK16
EFFECT RACK1- EFFECT
RACK8
ON B
GAIN 1A-GAIN 31A
GAIN 1B-GAIN 31B
Data List
24
INPUT ATT INPUT
CH 1-CH 72
*1
STIN1L-STIN8R
INPUT DYNAMICS1
ON
CH 1-CH 72
*1
STIN1L-STIN8R
ATTACK
THRESHOLD
RANGE
HOLD H
HOLD L
DECAY/RELEASE H
DECAY/RELEASE L
RATIO
KNEE
GAIN H
GAIN L
INPUT DYNAMICS2
ON
CH 1-CH 72
*1
STIN1L-STIN8R
ATTACK
THRESHOLD
RELEASE H
RELEASE L
RATIO/TYPE
GAIN H
GAIN L/Q
KNEE/WIDTH
FILTER FREQ
INPUT EQ
ON
CH 1-CH 72
*1
STIN1L-STIN8R
LOW Q
LOW FREQ
LOW GAIN
LOW MID Q
LOW MID FREQ
LOW MID GAIN
HIGH MID Q
HIGH MID FREQ
HIGH MID GAIN
HIGH Q
HIGH FREQ
HIGH GAIN
LPF ON
LOW TYPE
HIGH TYPE
INPUT HPF
ON
CH 1-CH 72
*1
STIN1L-STIN8R
FREQ
INSERT
INPUT
CH 1-CH 72
*1
OUTPUT
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
Mode Parameter 1 Parameter 2
LCR
ON
CH 1-CH 72
*1
STIN1L-STIN8R
MIX 1-MIX 24
CSR
MIX/MATRIX SEND
MIX 1 ON - MIX24 ON
CH 1-CH 72
*1
STIN1L-STIN8R
MATRIX 1 ON - MATRIX 8 ON
MIX 1 POINT - MIX 24 POINT
MATRIX 1 POINT - MATRIX 8 POINT
MIX 1 H - MIX24H
MATRIX1 H - MATRIX8 H
MIX 1 L - MIX24L
MATRIX1 L - MATRIX8 L
MIX 1/2 PAN - MIX 23/24 PAN
MATRIX1/2 PAN - MATRIX7/8 PAN
MIX TO MATRIX
MATRIX 1 POINT - MATRIX 8 POINT
MIX 1-MIX 24
MATRIX 1 ON - MATRIX 8 ON
MATRIX 1 LEVEL H - MATRIX 8 LEVEL H
MATRIX 1 LEVEL L - MATRIX 8 LEVEL L
MATRIX 1/2 PAN - MATRIX 7/8 PAN
MIX TO STEREO
TO STEREO ON
MIX 1-MIX 24TO MONO ON
PAN
MONITOR
OUTPUT
SOURCE SELECT
DEFINE ASSIGN
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
OMNI 1-2-OMNI 7-8
PB OUT
DIMMER ON
PHONES LEVEL LINK
CUE INTERRUPTION
MONO MONITOR
MONITOR FADER H
MONITOR FADER L
DELAY AUTO BYPASS
DELAY ON
MUTE MASTER ON MASTER 1-MASTER 8
OUTPUT ATT OUTPUT
MIX1-MIX24
MATRIX1-MATRIX8
STEREO L-MONO(C)
OUTPUT DYNAMICS1
ON
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
ATTACK
THRESHOLD
RELEASE H
RELEASE L
RATIO
GAIN H
GAIN L
KNEE/WIDTH
Mode Parameter 1 Parameter 2
Data List
25
OUTPUT EQ
ON
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
LOW Q
LOW FREQ
LOW GAIN
LOW MID Q
LOW MID FREQ
LOW MID GAIN
HIGH MID Q
HIGH MID FREQ
HIGH MID GAIN
HIGH Q
HIGH FREQ
HIGH GAIN
LOW TYPE
HIGH TYPE
LOW HPF ON
HIGH LPF ON
PAN/BALANCE INPUT
CH 1-CH 72
*1
STIN1L-STIN8R
PEQ
A/B LINK
GEQ RACK 1A-16B
EFFECT RACK 1A-8B
ON
BAND1 BYPASS
BAND1 GAIN H
BAND1 GAIN L
BAND1 FREQ
BAND1 Q
BAND2 BYPASS
BAND2 GAIN H
BAND2 GAIN L
BAND2 FREQ
BAND2 Q
BAND3 BYPASS
BAND3 GAIN H
BAND3 GAIN L
BAND3 FREQ
BAND3 Q
BAND4 BYPASS
BAND4 GAIN H
Mode Parameter 1 Parameter 2
PEQ
BAND4 GAIN L
GEQ RACK 1A-16B
EFFECT RACK 1A-8B
BAND4 FREQ
BAND4 Q
BAND5 BYPASS
BAND5 GAIN H
BAND5 GAIN L
BAND5 FREQ
BAND5 Q
BAND6 BYPASS
BAND6 GAIN H
BAND6 GAIN L
BAND6 FREQ
BAND6 Q
BAND7 BYPASS
BAND7 GAIN H
BAND7 GAIN L
BAND7 FREQ
BAND7 Q
BAND8 BYPASS
BAND8 GAIN H
BAND8 GAIN L
BAND8 FREQ
BAND8 Q
HPF ON
HPF FREQ
HPF SLOPE
LPF ON
LPF FREQ
LPF SLOPE
NOTCH A ON
NOTCH A FREQ H
NOTCH A FREQ L
NOTCH A Q
NOTCH B ON
NOTCH B FREQ H
NOTCH B FREQ L
NOTCH B Q
NOTCH C ON
NOTCH C FREQ H
NOTCH C FREQ L
NOTCH C Q
PHASE INPUT
CH 1-CH 72
*1
STIN1L-STIN8R
PREMIUM EFFECT A
BYPASS
RACK1-8
PARAM 1 H - PARAM 64 L
PREMIUM EFFECT B
BYPASS
RACK1-8
PARAM 1 H - PARAM 64 L
Mode Parameter 1 Parameter 2
Data List
26
RECALL SAFE ON
CH 1-CH 72
*1
STIN1L-STIN8R
MIX 1-MIX 24
MATRIX 1-MATRIX 8
STEREO L-MONO(C)
GEQ RACK 1A-16B
EFFECT RACK 1A-8B
PREMIUM RACK 1A-8B
DCA 1-DCA16
STEREO TO MATRIX
MATRIX 1 POINT - MATRIX 8 POINT
STEREO L-MONO(C)
MATRIX 1 ON - MATRIX 8 ON
MATRIX 1 LEVEL H - MATRIX 8 LEVEL H
MATRIX 1 LEVEL L - MATRIX 8 LEVEL L
MATRIX 1/2 PAN - MATRIX 7/8 PAN
SURROUND MONITOR
SOURCE SELECT
2CH MONITOR ASSIGN
DOWNMIX
SURROUND SPEAKER SOLO
SURROUND SPEAKER L
SURROUND SPEAKER R
SURROUND SPEAKER C
SURROUND SPEAKER LFE
SURROUND SPEAKER Ls
SURROUND SPEAKER Rs
SURROUND PAN
LR PAN
SELECTED CH
CH 1-CH 72
*1
STIN1L-STIN8R
FR PAN
FR PAN REVERSE
DIV
L ON
R ON
C ON
LFE ON
Ls ON
Rs ON
LFE LEVEL H
LFE LEVEL L
TO MONO ON
CH 1-CH 72
*1
STIN1L-STIN8R
TO STEREO ON
CH 1-CH 72
*1
STIN1L-STIN8R
*1. CL3: CH1-CH64, CL1: CH1-CH48
Mode Parameter 1 Parameter 2
Data List
27
NRPN Parameter Assignments
Parameter From (HEX) To (HEX)
FADER
INPUT 0000 0057
MIX1-20, MATRIX,
STEREO LR
0060 007D
INPUT to MIX9-16 LEVEL
MIX9 SEND 007E 00D5
MIX10 SEND 00DE 0135
MIX11 SEND 013E 0195
MIX12 SEND 019E 01F5
MIX13 SEND 01FE 0255
MIX14 SEND 025E 02B5
MIX15 SEND 02BE 0315
MIX16 SEND 031E 0375
INPUT to MATRIX1 - 4
LEVEL
MATRIX1 SEND 037E 03D5
MATRIX2 SEND 03DE 0435
MATRIX3 SEND 043E 0495
MATRIX4 SEND 049E 04F5
MIX1-20, STEREO LR to
MATRIX LEVEL
MATRIX1 SEND 04FE 0513
MATRIX2 SEND 0514 0529
MATRIX3 SEND 052A 053F
MATRIX4 SEND 0540 0555
MATRIX5 SEND 0556 056B
MATRIX6 SEND 056C 0581
MATRIX7 SEND 0582 0597
MATRIX8 SEND 0598 05AD
ON
INPUT 05B6 060D
MIX1-20, MATRIX,
STEREO LR
0616 0633
INPUT to MIX9-16 ON
MIX9 SEND 0634 068B
MIX10 SEND 0694 06EB
MIX11 SEND 06F4 074B
MIX12 SEND 0754 07AB
MIX13 SEND 07B4 080B
MIX14 SEND 0814 086B
MIX15 SEND 0874 08CB
MIX16 SEND 08D4 092B
INPUT to MATRIX1-4 ON
MATRIX1 SEND 0934 098B
MATRIX2 SEND 0994 09EB
MATRIX3 SEND 09F4 0A4B
MATRIX4 SEND 0A54 0AAB
MIX1-20, STEREO LR to
MATRIX ON
MATRIX1 SEND 0AB4 0AC9
MATRIX2 SEND 0ACA 0ADF
MATRIX3 SEND 0AE0 0AF5
MATRIX4 SEND 0AF6 0B0B
MATRIX5 SEND 0B0C 0B21
MATRIX6 SEND 0B22 0B37
MATRIX7 SEND 0B38 0B4D
MATRIX8 SEND 0B4E 0B63
MIX1-8 to STEREO ON MIX TO ST 0B64 0B6B
PHASE INPUT 0B6C 0BC3
INSERT ON
INPUT 0BCC 0C13
MIX1-20, MATRIX,
STEREO LR
0C2C 0C49
INPUT to MIX9-16 PRE/
POST
MIX9 SEND 0C4A 0CA1
MIX10 SEND 0CAA 0D01
MIX11 SEND 0D0A 0D61
MIX12 SEND 0D6A 0DC1
MIX13 SEND 0DCA 0E21
MIX14 SEND 0E2A 0E81
MIX15 SEND 0E8A 0EE1
MIX16 SEND 0EEA 0F41
INPUT to MATRIX1-4
PRE/POST
MATRIX1 SEND 0F4A 0FA1
MATRIX2 SEND 0FAA 1001
MATRIX3 SEND 100A 1061
MATRIX4 SEND 106A 10C1
INPUT57-64 to MIX1-8
LEVEL
MIX1 SEND 10CA 10D1
MIX2 SEND 10D2 10D9
MIX3 SEND 10DA 10E1
MIX4 SEND 10E2 10E9
MIX5 SEND 10EA 10F1
MIX6 SEND 10F2 10F9
MIX7 SEND 10FA 1101
MIX8 SEND 1102 1109
INPUT57-64 to
MATRIX5-8 LEVEL
MATRIX5 SEND 110A 1111
MATRIX6 SEND 1112 1119
MATRIX7 SEND 111A 1121
MATRIX8 SEND 1122 1129
INPUT57-64 to MIX1-8
ON
MIX1 SEND 112A 1131
MIX2 SEND 1132 1139
MIX3 SEND 113A 1141
MIX4 SEND 1142 1149
MIX5 SEND 114A 1151
MIX6 SEND 1152 1159
MIX7 SEND 115A 1161
MIX8 SEND 1162 1169
INPUT57-64 to
MATRIX5-8 ON
MATRIX5 SEND 116A 1171
MATRIX6 SEND 1172 1179
MATRIX7 SEND 117A 1181
MATRIX8 SEND 1182 1189
INPUT57-64 to MIX1-8
PRE/POST
MIX1 SEND 118A 1191
MIX2 SEND 1192 1199
MIX3 SEND 119A 11A1
MIX4 SEND 11A2 11A9
MIX5 SEND 11AA 11B1
MIX6 SEND 11B2 11B9
MIX7 SEND 11BA 11C1
MIX8 SEND 11C2 11C9
INPUT57-64 to
MATRIX5-8 PRE/POST
MATRIX5 SEND 11CA 11D1
MATRIX6 SEND 11D2 11D9
MATRIX7 SEND 11DA 11E1
MATRIX8 SEND 11E2 11E9
Parameter From (HEX) To (HEX)
INPUT57-64 EQ
LOW TYPE 11EA 11F1
HIGH TYPE 11F2 11F9
INPUT57-64 HPF FREQ 11FA 1201
INPUT57-64 to MIX1/2-
7/8 PAN
MIX1/2 1202 1209
MIX3/4 120A 1211
MIX5/6 1212 1219
MIX7/8 121A 1221
INPUT57-64 to
MATRIX5/6, 7/8 PAN
MATRIX5/6 1222 1229
MATRIX7/8 122A 1231
INPUT57-64 to STEREO ON 1232 1239
INPUT57-64 RECALL
SAFE
ON 123A 1241
INPUT57-64 to MONO ON 1242 1249
INPUT49-64
DYNAMICS1
RATIO 124A 1259
KNEE/WIDTH 125A 1269
GAIN 126A 1279
INPUT49-64
DYNAMICS2
reserved 127A 1289
FILTER FREQ 128A 1299
INPUT65-72, STIN5-8
RECALL SAFE
ON 129A 12A9
EQ INPUT, MIX1-20,
MATRIX, STEREO LR
ON 1304 1381
LOW Q 1382 13FF
LOW FREQ 1400 147D
LOW GAIN 147E 14FB
LOW MID Q 14FC 1579
LOW MID FREQ 157A 15F7
LOW MID GAIN 15F8 1675
HIGH MID Q 1676 16F3
HIGH MID FREQ 16F4 1771
HIGH MID GAIN 1772 17EF
HIGH Q 17F0 186D
HIGH FREQ 186E 18EB
HIGH GAIN 18EC 1969
ATT 196A 19C1
HPF ON 19E8 1A65
LPF ON 1A66 1AE3
INPUT DYNAMICS1
ON 1AE4 1B3B
ATTACK 1B44 1B9B
THRESHOLD 1BA4 1BFB
RANGE 1C04 1C5B
HOLD 1C64 1CBB
DECAY/RELEASE 1CC4 1D1B
INPUT DYNAMICS2 ON 1D24 1DA1
MIX1-20, MATRIX,
STEREO LR DYNAMICS1
ATTACK 1DA2 1E1F
THRESHOLD 1E20 1E9D
RELEASE 1E9E 1F1B
RATIO 1F1C 1F99
GAIN 1F9A 2017
KNEE/WIDTH 2018 2095
PAN/BALANCE INPUT 2096 20ED
Parameter From (HEX) To (HEX)
Data List
28
INPUT to MIX9/10-15/16
PAN
MIX9/10 20F6 214D
MIX11/12 2156 21AD
MIX13/14 21B6 220D
MIX15/16 2216 226D
INPUT to MATRIX1/2,
3/4 PAN
MATRIX1/2 2276 22CD
MATRIX3/4 22D6 232D
MIX1-20, STEREO LR to
MATRIX PAN
MATRIX1/2 2336 234B
MATRIX3/4 234C 2361
MATRIX5/6 2362 2377
MATRIX7/8 2378 238D
MIX1-8 to STEREO PAN MIX TO ST 238E 2395
BALANCE
MIX1-20, MATRIX,
STEREO LR
2396 23B3
MIX, STEREO LR, MONO
to MATRIX PRE/POST
MATRIX1 SEND 23B4 23CE
MATRIX2 SEND 23D0 23EA
MATRIX3 SEND 23EC 2406
MATRIX4 SEND 2408 2422
MATRIX5 SEND 2424 243E
MATRIX6 SEND 2440 245A
MATRIX7 SEND 245C 2476
MATRIX8 SEND 2478 2492
MIX21-24, MONO to
MATRIX ON
MATRIX1 SEND 2494 2498
MATRIX2 SEND 249A 249E
MATRIX3 SEND 24A0 24A4
MATRIX4 SEND 24A6 24AA
MATRIX5 SEND 24AC 24B0
MATRIX6 SEND 24B2 24B6
MATRIX7 SEND 24B8 24BC
MATRIX8 SEND 24BE 24C2
INPUT65-72, STIN5-8 to
MIX1-8 LEVEL
MIX1 SEND 24C4 24D3
MIX2 SEND 24D4 24E3
MIX3 SEND 24E4 24F3
MIX4 SEND 24F4 2503
MIX5 SEND 2504 2513
MIX6 SEND 2514 2523
MIX7 SEND 2524 2533
MIX8 SEND 2534 2543
INPUT65-72, STIN5-8 to
MIX1-8 ON
MIX1 SEND 2544 2553
MIX2 SEND 2554 2563
MIX3 SEND 2564 2573
MIX4 SEND 2574 2583
MIX5 SEND 2584 2593
MIX6 SEND 2594 25A3
MIX7 SEND 25A4 25B3
MIX8 SEND 25B4 25C3
Parameter From (HEX) To (HEX)
INPUT65-72, STIN5-8 to
MIX1-8 PRE/POST
MIX1 SEND 25C4 25D3
MIX2 SEND 25D4 25E3
MIX3 SEND 25E4 25F3
MIX4 SEND 25F4 2603
MIX5 SEND 2604 2613
MIX6 SEND 2614 2623
MIX7 SEND 2624 2633
MIX8 SEND 2634 2643
INPUT65-72, STIN5-8 to
MIX1/2-7/8 PAN
MIX1/2 2644 2653
MIX3/4 2654 2663
MIX5/6 2664 2673
MIX7/8 2674 2683
EFFECT RACK1-8
BYPASS 26B4 26BB
MIX BALANCE 26BC 26C3
PARAM1 26C4 26CB
PARAM2 26CC 26D3
PARAM3 26D4 26DB
PARAM4 26DC 26E3
PARAM5 26E4 26EB
PARAM6 26EC 26F3
PARAM7 26F4 26FB
PARAM8 26FC 2703
PARAM9 2704 270B
PARAM10 270C 2713
PARAM11 2714 271B
PARAM12 271C 2723
PARAM13 2724 272B
PARAM14 272C 2733
PARAM15 2734 273B
PARAM16 273C 2743
PARAM17 2744 274B
PARAM18 274C 2753
PARAM19 2754 275B
PARAM20 275C 2763
PARAM21 2764 276B
PARAM22 276C 2773
PARAM23 2774 277B
PARAM24 277C 2783
PARAM25 2784 278B
PARAM26 278C 2793
PARAM27 2794 279B
PARAM28 279C 27A3
PARAM29 27A4 27AB
PARAM30 27AC 27B3
PARAM31 27B4 27BB
PARAM32 27BC 27C3
Parameter From (HEX) To (HEX)
GEQ RACK1A-3B
ON 27C4 27C9
GAIN1 27CA 27CF
GAIN2 27D0 27D5
GAIN3 27D6 27DB
GAIN4 27DC 27E1
GAIN5 27E2 27E7
GAIN6 27E8 27ED
GAIN7 27EE 27F3
GAIN8 27F4 27F9
GAIN9 27FA 27FF
GAIN10 2800 2805
GAIN11 2806 280B
GAIN12 280C 2811
GAIN13 2812 2817
GAIN14 2818 281D
GAIN15 281E 2823
GAIN16 2824 2829
GAIN17 282A 282F
GAIN18 2830 2835
GAIN19 2836 283B
GAIN20 283C 2841
GAIN21 2842 2847
GAIN22 2848 284D
GAIN23 284E 2853
GAIN24 2854 2859
GAIN25 285A 285F
GAIN26 2860 2865
GAIN27 2866 286B
GAIN28 286C 2871
GAIN29 2872 2877
GAIN30 2878 287D
GAIN31 287E 2883
FADER MIX21-24, MONO 28E4 28E8
INPUT1-56, STIN1-4 to
MIX1-8 LEVEL
MIX1 SEND 28EA 2929
MIX2 SEND 292A 2969
MIX3 SEND 296A 29A9
MIX4 SEND 29AA 29E9
MIX5 SEND 29EA 2A29
MIX6 SEND 2A2A 2A69
MIX7 SEND 2A6A 2AA9
MIX8 SEND 2AAA 2AE9
INPUT1-56, STIN1-4 to
MATRIX5-8 LEVEL
MATRIX5 SEND 2AEA 2B29
MATRIX6 SEND 2B2A 2B69
MATRIX7 SEND 2B6A 2BA9
MATRIX8 SEND 2BAA 2BE9
Parameter From (HEX) To (HEX)
Data List
29
MIX21-24, MONO to
MATRIX LEVEL
MATRIX1 SEND 2BEA 2BEE
MATRIX2 SEND 2BF0 2BF4
MATRIX3 SEND 2BF6 2BFA
MATRIX4 SEND 2BFC 2C00
MATRIX5 SEND 2C02 2C06
MATRIX6 SEND 2C08 2C0C
MATRIX7 SEND 2C0E 2C12
MATRIX8 SEND 2C14 2C18
ON MIX21-24, MONO 2C2A 2C2E
INPUT1-56, STIN1-4 to
MIX1-8 ON
MIX1 SEND 2C30 2C6F
MIX2 SEND 2C70 2CAF
MIX3 SEND 2CB0 2CEF
MIX4 SEND 2CF0 2D2F
MIX5 SEND 2D30 2D6F
MIX6 SEND 2D70 2DAF
MIX7 SEND 2DB0 2DEF
MIX8 SEND 2DF0 2E2F
INPUT1-56, STIN1-4 to
MATRIX5-8 ON
MATRIX5 SEND 2E30 2E6F
MATRIX6 SEND 2E70 2EAF
MATRIX7 SEND 2EB0 2EEF
MATRIX8 SEND 2EF0 2F2F
MIX9-24 to STEREO ON MIX TO ST 2F36 2F45
INSERT MIX21-24, MONO 2F46 2F4A
INPUT1-56, STIN1-4 to
MIX1-8 PRE/POST
MIX1 SEND 2F4C 2F8B
MIX2 SEND 2F8C 2FCB
MIX3 SEND 2FCC 300B
MIX4 SEND 300C 304B
MIX5 SEND 304C 308B
MIX6 SEND 308C 30CB
MIX7 SEND 30CC 310B
MIX8 SEND 310C 314B
INPUT1-56, STIN1-4 to
MATRIX5-8 PRE/POST
MATRIX5 SEND 314C 318B
MATRIX6 SEND 318C 31CB
MATRIX7 SEND 31CC 320B
MATRIX8 SEND 320C 324B
DCA13-16
ON 324C 324F
FADER 3252 3255
BALANCE MIX21-24 (,MONO) 3258 325C
MIX21-24, MONO EQ
ON 325E 3262
LOW Q 3264 3268
LOW FREQ 326A 326E
LOW GAIN 3270 3274
LOW MID Q 3276 327A
LOW MID FREQ 327C 3280
LOW MID GAIN 3282 3286
HIGH MID Q 3288 328C
HIGH MID FREQ 328E 3292
HIGH MID GAIN 3294 3298
HIGH Q 329A 329E
HIGH FREQ 32A0 32A4
HIGH GAIN 32A6 32AA
Parameter From (HEX) To (HEX)
MIX21-24, MONO EQ
HPF ON 32AC 32B0
LPF ON 32B2 32B6
INPUT1-56, STIN1-4 EQ
LOW TYPE 3440 347F
HIGH TYPE 3480 34BF
MIX, MATRIX, STEREO
LR, MONO EQ
LOW TYPE 34C0 34E2
HIGH TYPE 34E4 3506
INPUT65-72, STIN5-8 EQ
LOW TYPE 3508 3517
HIGH TYPE 3518 3527
INPUT65-72, STIN5-8
HPF
FREQ 3528 3537
DIRECT OUT INPUT65-
72
ON 3538 353F
INPUT65-72, STIN5-8 to
MATRIX5-8 LEVEL
MATRIX5 SEND 3540 354F
MATRIX6 SEND 3550 355F
MATRIX7 SEND 3560 356F
MATRIX8 SEND 3570 357F
INPUT65-72, STIN5-8 to
MATRIX5-8 ON
MATRIX5 SEND 3580 358F
MATRIX6 SEND 3590 359F
MATRIX7 SEND 35A0 35AF
MATRIX8 SEND 35B0 35BF
INPUT65-72, STIN5-8 to
MATRIX5-8 PRE/POST
MATRIX5 SEND 35C0 35CF
MATRIX6 SEND 35D0 35DF
MATRIX7 SEND 35E0 35EF
MATRIX8 SEND 35F0 35FF
INPUT65-72, STIN5-8 to
MATRIX5/6, 7/8 PAN
MATRIX5/6 3600 360F
MATRIX7/8 3610 361F
MONITOR
SURROUND MONITOR
FADER 3620 3620
SPEAKER MUTE
SOLO
3621 3621
SPEAKER MUTE L 3622 3622
SPEAKER MUTE R 3623 3623
SPEAKER MUTE C 3624 3624
SPEAKER MUTE LFE 3625 3625
SPEAKER MUTE Ls 3626 3626
SPEAKER MUTE Rs 3627 3627
INPUT1-56, STIN1-4 HPF FREQ 3640 367F
MIX21-24, MONO
DYNAMICS1
ON 3680 3684
ATTACK 3686 368A
THRESHOLD 368C 3690
RELEASE 3692 3696
RATIO 3698 369C
GAIN 369E 36A2
KNEE/WIDTH 36A4 36A8
INPUT1-56, STIN1-4 to
MIX1/2-7/8 PAN
MIX1/2 36AA 36E9
MIX3/4 36EA 3729
MIX5/6 372A 3769
MIX7/8 376A 37A9
INPUT1-56, STIN1-4 to
MATRIX5/6, 7/8 PAN
MATRIX5/6 37AA 37E9
MATRIX7/8 37EA 3829
Parameter From (HEX) To (HEX)
MIX21-24, MONO to
MATRIX1/2-7/8 PAN
MATRIX1/2 382A 382E
MATRIX3/4 3830 3834
MATRIX5/6 3836 383A
MATRIX7/8 383C 3840
MIX9-24 to STEREO PAN MIX TO ST 3842 3851
GEQ RACK4A-6B
ON 3852 3857
GAIN1 3858 385D
GAIN2 385E 3863
GAIN3 3864 3869
GAIN4 386A 386F
GAIN5 3870 3875
GAIN6 3876 387B
GAIN7 387C 3881
GAIN8 3882 3887
GAIN9 3888 388D
GAIN10 388E 3893
GAIN11 3894 3899
GAIN12 389A 389F
GAIN13 38A0 38A5
GAIN14 38A6 38AB
GAIN15 38AC 38B1
GAIN16 38B2 38B7
GAIN17 38B8 38BD
GAIN18 38BE 38C3
GAIN19 38C4 38C9
GAIN20 38CA 38CF
GAIN21 38D0 38D5
GAIN22 38D6 38DB
GAIN23 38DC 38E1
GAIN24 38E2 38E7
GAIN25 38E8 38ED
GAIN26 38EE 38F3
GAIN27 38F4 38F9
GAIN28 38FA 38FF
GAIN29 3900 3905
GAIN30 3906 390B
GAIN31 390C 3911
LCR INPUT1-64, STIN1-4,
MIX1-16
ON 3912 3969
CSR 396A 39C1
DIRECT OUT INPUT1-64 ON 39C2 3A01
INPUT1-56, STIN1-4 TO
STEREO
ON 3A02 3A41
DCA1-12
ON 3A42 3A4D
FADER 3A4E 3A59
MUTE MASTER ON 3A5A 3A61
RECALL SAFE ON 3A66 3B05
Parameter From (HEX) To (HEX)
Data List
30
HA
EXTERNAL GAIN1 3B06 3B0B
INPUT GAIN 1 3B0F 3B15
EXTERNAL GAIN2 3B16 3B1B
INPUT GAIN 2 3B1F 3B25
EXTERNAL GAIN3 3B26 3B2B
INPUT GAIN 3 3B2F 3B35
EXTERNAL GAIN4 3B36 3B3B
INPUT GAIN 4 3B3F 3B45
EXTERNAL GAIN5 3B46 3B4B
INPUT GAIN 5 3B4F 3B55
EXTERNAL GAIN6 3B56 3B5B
INPUT GAIN 6 3B5F 3B65
EXTERNAL GAIN7 3B66 3B6B
INPUT GAIN 7 3B6F 3B75
EXTERNAL GAIN8 3B76 3B7B
INPUT GAIN 8 3B7F 3B85
EXTERNAL +48V 1 3B86 3B8B
INPUT +48V 1 3B8F 3B95
EXTERNAL +48V 2 3B96 3B9B
INPUT +48V 2 3B9F 3BA5
EXTERNAL +48V 3 3BA6 3BAB
INPUT +48V 3 3BAF 3BB5
EXTERNAL +48V 4 3BB6 3BBB
INPUT +48V 4 3BBF 3BC5
EXTERNAL +48V 5 3BC6 3BCB
INPUT +48V 5 3BCF 3BD5
EXTERNAL +48V 6 3BD6 3BDB
INPUT +48V 6 3BDF 3BE5
EXTERNAL +48V 7 3BE6 3BEB
INPUT +48V 7 3BEF 3BF5
EXTERNAL +48V 8 3BF6 3BFB
INPUT +48V 8 3BFF 3C05
EXTERNAL HPF1 3C06 3C0B
INPUT HPF1 3C0F 3C15
EXTERNAL HPF2 3C16 3C1B
INPUT HPF2 3C1F 3C25
EXTERNAL HPF3 3C26 3C2B
INPUT HPF3 3C2F 3C35
EXTERNAL HPF4 3C36 3C3B
INPUT HPF4 3C3F 3C45
EXTERNAL HPF5 3C46 3C4B
INPUT HPF5 3C4F 3C55
EXTERNAL HPF6 3C56 3C5B
INPUT HPF6 3C5F 3C65
EXTERNAL HPF7 3C66 3C6B
INPUT HPF7 3C6F 3C75
EXTERNAL HPF8 3C76 3C7B
INPUT HPF8 3C7F 3C85
INPUT1-56, STIN1-4 TO
MONO
ON 3C86 3CC5
MIX1-16 TO MONO ON 3CC6 3CD5
Parameter From (HEX) To (HEX)
SLOT OUT DELAY
ON 3CD6 3D05
TIME HIGH 3D06 3D35
TIME LOW 3D36 3D65
OMNI OUT DELAY
ON 3D66 3D6D
TIME HIGH 3D76 3D7D
TIME LOW 3D86 3D8D
DIGITAL OUT DELAY
ON 3D96 3D97
TIME HIGH 3D98 3D99
TIME LOW 3D9A 3D9B
INPUT1-48, STIN1-4
DYNAMICS1
RATIO 3D9C 3DD3
KNEE/WIDTH 3DD4 3E0B
GAIN 3E0C 3E43
INPUT1-48, STIN1-4
DYNAMICS2
reserved 3E44 3E7B
FILTER FREQ 3E7C 3EB3
GEQ RACK7A-8B
ON 3EB4 3EB7
GAIN1 3EB8 3EBB
GAIN2 3EBC 3EBF
GAIN3 3EC0 3EC3
GAIN4 3EC4 3EC7
GAIN5 3EC8 3ECB
GAIN6 3ECC 3ECF
GAIN7 3ED0 3ED3
GAIN8 3ED4 3ED7
GAIN9 3ED8 3EDB
GAIN10 3EDC 3EDF
GAIN11 3EE0 3EE3
GAIN12 3EE4 3EE7
GAIN13 3EE8 3EEB
GAIN14 3EEC 3EEF
GAIN15 3EF0 3EF3
GAIN16 3EF4 3EF7
GAIN17 3EF8 3EFB
GAIN18 3EFC 3EFF
GAIN19 3F00 3F03
GAIN20 3F04 3F07
GAIN21 3F08 3F0B
GAIN22 3F0C 3F0F
GAIN23 3F10 3F13
GAIN24 3F14 3F17
GAIN25 3F18 3F1B
GAIN26 3F1C 3F1F
GAIN27 3F20 3F23
GAIN28 3F24 3F27
GAIN29 3F28 3F2B
GAIN30 3F2C 3F2F
GAIN31 3F30 3F33
Parameter From (HEX) To (HEX)
MIX, MATRIX, STEREO
LR, MONO EQ
ATT 3F34 3F56
INPUT65-72, STIN5-8 TO
STEREO
ON 3F58 3F67
INPUT65-72, STIN5-8,
MIX17-24 TO MONO
ON 3F68 3F7F
LCR IN65-72, STIN5-8,
MIX17-24
ON 3F80 3F97
CSR 3F98 3FAF
INPUT65-72, STIN5-8
DYNAMICS1
RATIO 3FB0 3FBF
KNEE/WIDTH 3FC0 3FCF
GAIN 3FD0 3FDF
INPUT65-72, STIN5-8
DYNAMICS2
reserved 3FE0 3FEF
FILTER FREQ 3FF0 3FFF
Parameter From (HEX) To (HEX)
Data List
31
Mixing Parameter Operation Applicability
This table indicates which settings affect the behavior of each input channel and output channel parameter.
It also indicates whether or not they can be linked as stereo, and whether or not they are relevant to the RECALL SAFE, GLOBAL PASTE, and USER LEVEL settings, and a channel library.
Input channels
Parameter Stereo
*1
CHANNEL LINK
RECALL SAFE, FOCUS RECALL, GLOBAL PASTE
*8
USER LEVEL
Channel
Library
ALL Parameter Select button
HA
Gain
O
*10
HA
*10
O HA, GLOBAL HA HA O
Gain Compensation O HA O HA, GLOBAL HA HA O
+48V
O HA, GLOBAL HA HA O
Phase
O HA, GLOBAL HA HA O
AG-DG Link O HA O HA, GLOBAL HA HA O
Digital Gain
O
*10
DIGITAL GAIN
*10
O DIGITAL GAIN HA O
Name, Icon, Color
O INPUT NAME, GLOBAL INPUT NAME INPUT NAME O
Input Patch
O INPUT PATCH, GLOBAL INPUT PATCH INPUT PATCH
LR-MONO
SELECT
* ST IN channels only O
ALL INPUT TO ST INPUT PROCESSING O
Insert1,
Insert2
Out Patch
O INPUT INSERT PATCH, GLOBAL INPUT PATCH INPUT PATCH
In Patch O INPUT INSERT PATCH, GLOBAL INPUT PATCH INPUT PATCH
+48V, Gain, Gain Compensation INPUT INSERT PATCH, GLOBAL HA HA
On INPUT INSERT O INPUT INSERT INPUT PROCESSING O
Point
INPUT INSERT O INPUT INSERT INPUT PROCESSING O
Direct Out
Out Patch
O INPUT DIRECT OUT, GLOBAL INPUT PATCH INPUT PATCH
On, Level DIRECT OUT O INPUT DIRECT OUT INPUT PROCESSING O
Point
DIRECT OUT O INPUT DIRECT OUT INPUT PROCESSING O
HPF O INPUT HPF O INPUT HPF INPUT PROCESSING O
Att O INPUT EQ O INPUT EQ INPUT PROCESSING O
EQ O INPUT EQ O INPUT EQ INPUT PROCESSING O
Dynamics1
Key-In Source
O INPUT DYNA1 INPUT PROCESSING
Key-In Filter O INPUT DYNAMICS1 O INPUT DYNA1 INPUT PROCESSING O
Others O INPUT DYNAMICS1 O INPUT DYNA1 INPUT PROCESSING O
Dynamics2
Key-In Source
O INPUT DYNA2 INPUT PROCESSING
Others O INPUT DYNAMICS2 O INPUT DYNA2 INPUT PROCESSING O
To Mix
On O
INPUT MIX ON
*2
O
INPUT MIX ON
*7
INPUT FADER/ON
*4
O
Level O
INPUT MIX SEND
*2
O
INPUT MIX SEND
*7
INPUT FADER/ON
*4
O
Pan/Balance
O
*11
O
INPUT MIX SEND
*7
INPUT FADER/ON
*4
O
Pre/Post O
INPUT MIX SEND
*2
O
INPUT MIX SEND
*7
INPUT PROCESSING
*4
O
Surround
Pan
O INPUT MIX SEND INPUT PROCESSING O
Divergence O
O INPUT MIX SEND INPUT PROCESSING O
LFE O
O INPUT MIX SEND INPUT PROCESSING O
Data List
32
*1 These parameters can be linked between L and R of ST IN channels 1-8.
*2 Applies to parameters for which the MIX channel 1-24 individual Send Parameter setting and the item in the table are both enabled.
*3 Applies to parameters for which the MATRIX channel 1-8 individual Send Parameter setting and the item in the table are both enabled.
*4 These parameters are available if “FADER/ON” or “PROCESSINGfor the Send source channel is set to ON. At that time, “WITH SEND” for the Send destination channel must also be set to ON.
*5 Applicable to parameters that function only when ALL is selected.
*6 Applicable only to On/Off.
*7 Valid when they are set for either the Send source channel or Send destination channel.
*8 Settings marked GLOBAL in this table apply to all channels; these settings are GLOBAL RECALL SAFE, FOCUS PARAMETER, and GLOBAL PASTE for PATCH/NAME.
*9 Applies to ALL only when using GLOBAL PASTE, and only to ON/OFF.
*10 Operates differentially
*11 Balance only
*14 Applicable to parameters only when ALL is selected.
To Matrix
On O
INPUT MATRIX ON
*3
O
INPUT MATRIX ON
*7
INPUT FADER/ON
*4
O
Level O
INPUT MATRIX SEND
*3
O
INPUT MATRIX SEND
*7
INPUT FADER/ON
*4
O
Pan/Balance
O
*11
O
INPUT MATRIX SEND
*7
INPUT FADER/ON
*4
O
Pre/Post O
INPUT MATRIX SEND
*3
O
INPUT MATRIX SEND
*7
INPUT PROCESSING
*4
O
DELAY
ms
O
*10
INPUT DELAY
*10
O INPUT DELAY INPUT PROCESSING O
ON O INPUT DELAY O INPUT DELAY INPUT PROCESSING O
To Stereo O TO STEREO O INPUT TO ST INPUT PROCESSING O
To Mono O TO STEREO O INPUT TO MONO INPUT PROCESSING O
Pan/balance
O
*11
O INPUT TO ST INPUT FADER/ON O
Pan Mode O
O
*5
INPUT PROCESSING O
LCR
On O TO STEREO O
*5
INPUT PROCESSING O
CSR O TO STEREO O
*5
INPUT PROCESSING O
Mode O TO STEREO O
*5
INPUT PROCESSING O
On O INPUT CH ON O INPUT CH ON INPUT FADER/ON O
Fader
O
*10
INPUT FADER
*10
O INPUT FADER INPUT FADER/ON O
Mute Assign O INPUT MUTE O INPUT MUTE ASSIGN MUTE GROUP ASSIGN O
DCA Assign O INPUT DCA O INPUT DCA ASSIGN DCA GROUP ASSIGN O
Fade Time, On
O
*6
O
*9
STORE
O
*6
Channel Link O GLOBAL CH LINK
Cue O
Key In Cue
Mute Safe O
Recall Safe O EACH PARAMETER
Focus Recall O EACH PARAMETER
Global Paste O
Parameter Stereo
*1
CHANNEL LINK
RECALL SAFE, FOCUS RECALL, GLOBAL PASTE
*8
USER LEVEL
Channel
Library
ALL Parameter Select button
Data List
33
MIX Channels
*4 These parameters are available if “FADER/ON” or “PROCESSINGfor the Send source channel is set to ON. At that time, “WITH SEND” for the Send destination channel must also be set to ON.
*5 Applicable to parameters that function only when ALL is selected.
*6 Applicable only to On/Off.
*7 Valid when they are set for either the Send source channel or Send destination channel.
*8 Settings marked GLOBAL in this table apply to all channels; these settings are GLOBAL RECALL SAFE, FOCUS PARAMETER, and GLOBAL PASTE for PATCH/NAME.
Parameters
Linked for
a stereo
pair
CHANNEL LINK
RECALL SAFE, FOCUS RECALL, GLOBAL PASTE
*8, *12
USER LEVEL
Channel
Library
ALL Parameter Select button
Name, Icon, Color
O MIX NAME, GLOBAL OUTPUT NAME OUTPUT NAME O
Output Patch
O MIX OUTPUT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
Insert1,
Insert2
Out Patch
O MIX INSERT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
In Patch O MIX INSERT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
+48V, Gain, Gain Compensation O MIX INSERT PATCH, GLOBAL HA MIX PROCESSING
On O INSERT O MIX INSERT MIX PROCESSING O
Point O INSERT O MIX INSERT MIX PROCESSING O
Att O EQ O MIX EQ MIX PROCESSING O
EQ O EQ O MIX EQ MIX PROCESSING O
Dynamics1
Key-In Source
O MIX DYNA1 MIX PROCESSING
Others O DYNAMICS O MIX DYNA1 MIX PROCESSING O
To Matrix
On O TO MATRIX ON O
MIX MATRIX ON
*7
MIX FADER/ON
*4
O
Level
O
*13
TO MATRIX SEND O
MIX MATRIX SEND
*7
MIX FADER/ON
*4
O
Pan/Balance O TO MATRIX SEND O
MIX MATRIX SEND
*7
MIX FADER/ON
*4
O
Pre/Post O TO MATRIX SEND O
MIX MATRIX SEND
*7
MIX PROCESSING
*4
O
To Stereo O TO STEREO O MIX TO ST MIX PROCESSING O
To Mono O TO STEREO O MIX MONO MIX PROCESSING O
Pan/Balance
O
*11
O MIX TO ST, TO ST/BAL (GLOBAL PASTE ONLY) MIX FADER/ON O
LCR
On O TO STEREO O
*5
MIX PROCESSING O
CSR O TO STEREO O
*5
MIX PROCESSING O
Mode O TO STEREO O
*5
MIX PROCESSING O
On O CH ON O MIX CH ON MIX FADER/ON O
Fader O FADER O MIX FADER MIX FADER/ON O
From Input
On O
WITH MIX SEND, WITH SEND FROM SOURCE CHs
WITH MIX SEND
*4
Level O WITH MIX SEND, WITH SEND FROM SOURCE CHs
WITH MIX SEND
*4
Pan/Balance
O
*11
WITH MIX SEND, WITH SEND FROM SOURCE CHs
WITH MIX SEND
*4
Pre/Post O WITH MIX SEND, WITH SEND FROM SOURCE CHs
WITH MIX SEND
*4
Mute Assign O MUTE O MIX MUTE ASSIGN MUTE GROUP ASSIGN O
DCA Assign O DCA O MIX DCA ASSIGN DCA GROUP ASSIGN O
Fade Time, On
O
*6
O
*9
STORE
O
*6
Channel Link O GLOBAL CH LINK
Cue O
Mute Safe O
Recall Safe O EACH PARAMETER
Focus Recall O EACH PARAMETER
Global Paste O
Data List
34
*9 Applies to ALL only when using GLOBAL PASTE, and only to ON/OFF.
*11 Balance only
*12 For GLOBAL PASTE, the MIX, MATRIX, STEREO, and MONO settings of each channel will be set in common as the OUTPUT.
*13 Linked only for stereo MATRIX
*14 Applicable to parameters only when ALL is selected.
MATRIX Channels
*4 These parameters are available if “FADER/ON” or “PROCESSINGfor the Send source channel is set to ON. At that time, “WITH SEND” for the Send destination channel must also be set to ON.
*5 Applicable to parameters that function only when ALL is selected.
*6 Applicable only to On/Off.
Parameters
Linked for
a stereo
pair
CHANNEL LINK
RECALL SAFE, FOCUS RECALL, GLOBAL PASTE
*8, *12
USER LEVEL
Channel
Library
ALL Parameter Select button
Name, Icon, Color
O MATRIX NAME,GLOBAL OUTPUT NAME OUTPUT NAME O
Output Patch
O MATRIX OUTPUT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
Insert1, Insert2
Out Patch
O MATRIX INSERT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
In Patch O MATRIX INSERT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
+48V, Gain, Gain
Compensation
O MATRIX INSERT PATCH, GLOBAL HA MATRIX PROCESSING
On O INSERT O MATRIX INSERT MATRIX PROCESSING O
Point O INSERT O MATRIX INSERT MATRIX PROCESSING O
Att O EQ O MATRIX EQ MATRIX PROCESSING O
EQ O EQ O MATRIX EQ MATRIX PROCESSING O
Dynamics1
Key-In Source
O MATRIX DYNA1 MATRIX PROCESSING
Others O DYNAMICS O MATRIX DYNA1 MATRIX PROCESSING O
To Matrix
On TO MATRIX ON
Level TO MATRIX SEND
Pan/Balance TO MATRIX SEND
Pre/Post TO MATRIX SEND
Balance O
O MATRIX BAL, TO ST/BAL (GLOBAL PASTE ONLY) MATRIX FADER/ON O
On O CH ON O MATRIX CH ON MATRIX FADER/ON O
Fader O FADER O MATRIX FADER MATRIX FADER/ON O
From Input
From Mix
From Stereo/Mono
On O
WITH MATRIX SEND, WITH SEND FROM SOURCE CHs
WITH MATRIX SEND
*4
Level O WITH MATRIX SEND, WITH SEND FROM SOURCE CHs
WITH MATRIX SEND
*4
Pan/Balance
O
*11
WITH MATRIX SEND, WITH SEND FROM SOURCE CHs
WITH MATRIX SEND
*4
Pre/Post O WITH MATRIX SEND, WITH SEND FROM SOURCE CHs
WITH MATRIX SEND
*4
Mute Assign O MUTE O MATRIX MUTE ASSIGN MUTE GROUP ASSIGN O
DCA Assign O DCA O MATRIX DCA ASSIGN DCA GROUP ASSIGN O
Fade Time, On
O
*6
O
*9
STORE
O
*6
Channel Link O GLOBAL CH LINK
Cue O
Mute Safe O
Recall Safe O EACH PARAMETER
Focus Recall O EACH PARAMETER
Global Paste O
Data List
35
*7 Valid when they are set for either the Send source channel or Send destination channel.
*8 Settings marked GLOBAL in this table apply to all channels; these settings are GLOBAL RECALL SAFE, FOCUS PARAMETER, and GLOBAL PASTE for PATCH/NAME.
*9 Applies to ALL only when using GLOBAL PASTE, and only to ON/OFF.
*11 Balance only
*12 For GLOBAL PASTE, the MIX, MATRIX, STEREO, and MONO settings of each channel will be set in common as the OUTPUT.
*14 Applicable to parameters only when ALL is selected.
STEREO, MONO Channels
*4 These parameters are available if “FADER/ON” or “PROCESSINGfor the Send source channel is set to ON. At that time, “WITH SEND” for the Send destination channel must also be set to ON.
*5 Applicable to parameters that function only when ALL is selected.
*6 Applicable only to On/Off.
*7 Valid when they are set for either the Send source channel or Send destination channel.
*8 Settings marked GLOBAL in this table apply to all channels; these settings are GLOBAL RECALL SAFE, FOCUS PARAMETER, and GLOBAL PASTE for PATCH/NAME.
*9 Applies to ALL only when using GLOBAL PASTE, and only to ON/OFF.
*12 For GLOBAL PASTE, the MIX, MATRIX, STEREO, and MONO settings of each channel will be set in common as the OUTPUT.
*14 Applicable to parameters only when ALL is selected.
Parameter
Linked for
a stereo
pair
RECALL SAFE, FOCUS RECALL, GLOBAL PASTE
*8, *12
USER LEVEL
Channel
Library
ALL Parameter Select button
Name, Icon, Color
O STEREO, MONO NAME, GLOBAL OUTPUT NAME OUTPUT NAME O
Output Patch
O STEREO, MONO OUTPUT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
Insert1, Insert2
Out Patch
O STEREO, MONO INSERT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
In Patch O STEREO, MONO INSERT PATCH, GLOBAL OUTPUT PATCH OUTPUT PATCH
+48V, Gain, Gain
Compensation
STEREO, MONO INSERT PATCH, GLOBAL HA STEREO, MONO PROCESSING
On O O STEREO, MONO INSERT STEREO, MONO PROCESSING O
Point O O STEREO, MONO INSERT STEREO, MONO PROCESSING O
Att O O STEREO, MONO EQ STEREO, MONO PROCESSING O
EQ O O STEREO, MONO EQ STEREO, MONO PROCESSING O
Dynamics1
Key-In Source
O STEREO, MONO DYNA1 STEREO, MONO PROCESSING
Others O O STEREO, MONO DYNA1 STEREO, MONO PROCESSING O
To Matrix
On O O
STEREO, MONO MATRIX ON
*7
STEREO, MONO FADER/ON
*4
O
Level
O
*13
O
STEREO, MONO MATRIX SEND
*7
STEREO, MONO FADER/ON
*4
O
Pan/Balance O O
STEREO, MONO MATRIX SEND
*7
STEREO, MONO FADER/ON
*4
O
Pre/Post O O
STEREO, MONO MATRIX SEND
*7
STEREO, MONO PROCESSING
*4
O
Balance O O STEREO, MONO BAL, TO ST/BAL (GLOBAL PASTE ONLY) STEREO, MONO FADER/ON O
On O O STEREO, MONO CH ON STEREO, MONO FADER/ON O
Fader O O STEREO, MONO FADER STEREO, MONO FADER/ON O
Mute Assign O O STEREO, MONO MUTE ASSIGN MUTE GROUP ASSIGN O
DCA Assign O O STEREO, MONO DCA ASSIGN DCA GROUP ASSIGN O
Fade Time, On
O
*6
O
*9
STORE
O
*6
Cue O
Mute Safe O
Recall Safe, Focus Recall, Global Paste O
Data List
36
DCA
*9 Applies to ALL only when using GLOBAL PASTE, and only to ON/OFF.
BUS SETUP
SURROUND BUS
MUTE
Parameters
RECALL SAFE, FOCUS RECALL, GLOBAL PASTE
USER LEVEL
ALL Parameter Select button
Name, Icon, Color O DCA NAME DCA MASTER
On O DCA LEVEL/ON DCA MASTER
Fader O DCA LEVEL/ON DCA MASTER
Fade Time, On O
*9
STORE
Input DCA Assign
DCA GROUP ASSIGN
Parameters
RECALL SAFE, FOCUS RECALL, GLOBAL PASTE
USER LEVEL
ALL Parameter Select button
Stereo/Mono, Bus Type, Pan
Link
MIX 1/2, …, MATRIX 7/8 BUS SETUP
Parameters
RECALL SAFE, FOCUS RECALL, GLOBAL PASTE
USER LEVEL
ALL Parameter Select button
Stereo/Mono, Bus Type, Pan
Link
SURROUND SETUP BUS SETUP
Parameters
RECALL SAFE
USER LEVEL
ALL
Name O MUTE GROUP MASTER
On
MUTE GROUP MASTER
Dimmer
MUTE GROUP MASTER
MUTE Assign
MUTE GROUP ASSIGN
Data List
37
MIDI Data Format
This section explains the format of the data that the CL series
is able to understand, send, and receive.
1 CHANNEL MESSAGE
1.1 NOTE OFF (8n)
Reception
These messages are echoed to MIDI OUT if [OTHER COMMAND ECHO] is ON.
They are received if [Rx CH] matches, and used to control effects.
1.2 NOTE ON (9n)
Reception
These messages are echoed to MIDI OUT if [OTHER COMMAND ECHO] is ON.
They are received if [Rx CH] matches, and used to control effects.
1.3 CONTROL CHANGE (Bn)
Two types of CONTROL CHANGE can be transmitted and received; [NRPN]
(Non-Registered Parameter Numbers) and freely-assigned [TABLE] (1CH x 110)
messages. Select either [TABLE] or [NRPN].
Reception
These messages are echoed to MIDI OUT if [CONTROL CHANGE ECHO] is ON.
If [TABLE] is selected, these messages are received when [CONTROL CHANGE Rx]
is ON and [Rx CH] matches, and will control parameters according to the settings
of the [CONTROL CHANGE EVENT LIST]. For the parameters that can be
assigned, refer to “Parameters That Can Be Assigned to Control Changes
(page 23).
If [NRPN] is selected, these messages are received when [CONTROL CHANGE Rx]
is ON and the [Rx CH] matches; the four messages NRPN control number (62h,
63h) and DATA ENTRY control number (06h, 26h) are used to control the
specified parameter.
Transmission
If [TABLE] is selected, and if [CONTROL CHANGE Tx] is ON when you operate a
parameter that is assigned in the [CONTROL CHANGE EVENT LIST], these
messages will be transmitted on the [Tx CH] channel. For the parameters that can
be assigned, refer to “Parameters That Can Be Assigned to Control Changes
(page 23).
If [NRPN] is selected, and if [CONTROL CHANGE Tx] is ON when you operate a
specified parameter, the four messages NRPN control number (62h, 63h) and
DATA ENTRY control number (06h, 26h) are transmitted on the [Tx CH] channel.
For the parameters that can be assigned, refer to “Parameters That Can Be
Assigned to Control Changes” (page 23).
CONTROL CHANGE messages are not used for transmission to CL Editor because
there is no guarantee that the contents of the assignment tables will match.
(PARAMETER CHANGE messages are always used.)
CONTROL CHANGE numbers 0 and 32 are for selecting banks.
If [TABLE] is selected
Equation for converting a Control Value to parameter data
paramSteps = paramMax-paramMin + 1;
add = paramWidth / paramSteps;
mod = paramWidth-add * paramSteps;
curValue = paramSteps * add + mod / 2;
(1) If the assigned parameter has fewer than 128 steps
paramWidth = 128; rxValue = Control value;
(2) If the assigned parameter has 128 or more but less than 16,384 steps
paramWidth = 16384;
(2-1) When High and Low data is received
rxValue = Control value(High) * 128 + Control value(Low);
(2-2) When only Low data is received
rxValue = (curValue & 16256) + Control value(Low);
(2-3) When only High data is received
rxValue = Control value(High) * 128 + (curValue & 127);
(3) If the assigned parameter has 16,384 or more but less than 2,097,152
steps
paramWidth = 2097152;
(3-1) When High, Middle, and Low data is received
rxValue = Control value(High) * 16384 + Control value(Middle) * 128 + Control value(Low);
(3-2) When only Low data is received
rxValue = (curValue & 2097024) + Control value(Low);
(3-3) When only Middle data is received
rxValue = (curValue & 2080895) + Control value(Middle) * 128;
(3-4) When only High data is received
rxValue = (curValue & 16383) + Control value(High) * 16384;
(3-5) When only Middle and Low data is received
rxValue = (curValue & 2080768) + Control value(Middle) * 128 + Control value(Low);
(3-6) When only High and Low data is received
rxValue = (curValue & 16256) + Control value(High) * 16384 + Control value(Low);
(3-7) When only High and Middle data is received
rxValue = (curValue & 127) + Control value(High) * 16384 + Control value(Middle) * 128;
if ( rxValue > paramWidth)
rxValue = paramWidth;
param = ( rxValue-mod / 2) / add;
If [NRPN] is selected
1.4 PROGRAM CHANGE (Cn)
Reception
If [PROGRAM CHANGE ECHO] is ON, bank select messages will also be echoed
from MIDI OUT.
If SINGLE CH is selected, these messages are received if [PROGRAM CHANGE Rx]
is ON and the [Rx CH] matches. However if [OMNI] is ON, these messages are
received regardless of the channel. When these messages are received, scene
memory, effect library and premium rack library are recalled according to the
settings of the [PROGRAM CHANGE EVENT LIST].
Transmission
If [PROGRAM CHANGE Tx] is ON, these messages are transmitted according to
the [PROGRAM CHANGE Table] settings when scene memory, effect library and
premium rack library are recalled.
If SINGLE CH is selected, these messages are transmitted on the [Tx CH] channel.
If the recalled scene memory, effect library and premium rack library have been
assigned to more than one PROGRAM NUMBER, the lowest-numbered
PROGRAM NUMBER for each MIDI channel will be transmitted.
PROGRAM CHANGE messages are not used for transmission to CL Editor because
there is no guarantee that the contents of the assignment tables will match.
(PARAMETER CHANGE messages are always used.)
You can choose either MULTI MIDI CH or SINGLE CH.
If SINGLE is selected
You can choose the Rx CH, OMNI CH, and Tx CH.
You can choose whether a bank select message will be added.
A bank of up to 16 can be specified.
If MULTI is selected
The Rx and Tx channels will be the same.
The assignment table will use the settings for each MIDI channel. Bank select
messages will not be added.
You can make settings for up to sixteen MIDI channels.
STATUS 1000nnnn 8n
Note off message
DATA 0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity (ignored)
STATUS 1001nnnn 9n
Note on message
DATA 0nnnnnnn nn
Note number
0vvvvvvv vv
Velocity (1-127:on, 0:off)
STATUS 1011nnnn Bn
Control change
DATA 00
Control number (00)
0vvvvvvv vv
Control Value (0-127)
STATUS 1011nnnn Bn
Control change
DATA 20
Control number (32)
0vvvvvvv vv
Control Value (0-127)
STATUS 1011nnnn Bn
Control change
DATA 0nnnnnnn nn
Control number (1-5, 7-31, 33-37, 38-95,
102-119) *
0vvvvvvv vv
Control Value (0-127)
* Numbers 0, 32, and 96-101 cannot be used.
* Control number 6, 38 can be used.
STATUS 1011nnnn Bn
Control change
DATA 01100010 62
NRPN LSB
0vvvvvvv vv
Parameter number LSB
STATUS 1011nnnn Bn
Control change *
DATA 01100011 63
NRPN MSB
0vvvvvvv vv
Parameter number MSB
STATUS 1011nnnn Bn
Control change *
DATA 00000110 06
Data entry MSB
0vvvvvvv vv
Parameter data MSB
STATUS 1011nnnn Bn
Control change *
DATA 00100110 26
Data entry LSB
0vvvvvvv vv
Parameter data LSB
* The STATUS byte of the second and subsequent messages need not
be added during transmission.
Reception must occur correctly whether or not the status byte is
omitted.
STATUS 1100nnnn Cn
Program change
DATA 0nnnnnnn nn
Program number (0-127)
Data List
38
2 SYSTEM REALTIME MESSAGE
2.1 SONG SELECT (F3)
Reception
Select the track number shown in the TITLE LIST screen of the USB memory
recorder.
2.2 TIMING CLOCK (F8)
Reception
This message is used to control effects. This message is transmitted twenty-four
times per quarter note.
Echoing of this message depends on the OTHER item in the ECHO settings.
2.3 ACTIVE SENSING (FE)
Reception
Once this message has been received, MIDI communication will be initialized
(e.g., Running Status will be cleared) if no message is received for an interval of
400 ms.
This message is not subject to echoing.
2.4 SYSTEM RESET (FF)
Reception
When this message is received, MIDI communication will be initialized (e.g.,
Running Status will be cleared).
This message is not subject to echoing.
3 SYSTEM EXCLUSIVE MESSAGE
3.1 MMC
< MMC STOP >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and stops.
< MMC PLAY >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and starts playback.
< MMC DEFERED PLAY >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message and starts playback.
< MMC RECORD STROBE >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message, and if stopped, starts
recording.
< MMC PAUSE >
Reception
If the [DEVICE NO.] matches or is 7F, receives this message, and if playing, pauses.
3.2 BULK DUMP
This message is used to send or receive the contents of various memories stored
within the unit.
The basic format is as follows.
The CL series console uses the following data types for a bulk dump.
*1) 0-300 Scene Number (0 Request Only),
*2) 1-199 Input EQ Library Number (1-40 Request Only)
*3) 1-199 Output EQ Library Number (1-3 Request Only)
*4) 1-199 Dynamics Library Number (1-41 Request Only)
*5) 0-199 GEQ Library Number (0 Request Only)
*6) 1-199 Effect Library Number (1-27 Request Only)
*7) 512-583 Input 1-72,
*8) 584-599 STIN 1L-8R,
*9) 768-791 MIX 1-24,
*10) 1024-1031 MATRIX 1-8,
*11) 1280-1282 STEREO L-C,
*12) 512-530 GEQ 1-19, 531-538 EFFECT GEQ 1-8,
*13) 0-199 8BandPEQ Library Number (0 Request Only)
*14) 512-519 EFFECT 1-8,
*15) 512 Current Data,
*16) 768 Current Data with Recall Safe,
*17) 8192 Store Undo Data, 8193 Recall Undo Data, 8194 Clear Undo Data,
*18) 0-199 Input CH Library Number (0 Request Only),
*19) 0-199 Output CH Library Number (0 Request Only),
*20) 512-527 Premium Rack 1A, 1B, 2A, … 8A, 8B
*21) 0-100 Each Premium Effect Library Number (0 Request Only)
*22) 1536-1607 Input 1-72 (for Dynamics2),
*23) 1608-1623 STIN 1L-8R (for Dynamics2),
*24) 0-10 Dante Input Patch Library Number (0 Request Only)
Data is lost when you write to the preset library.
The unique header (Model ID) identifies whether the device is a CL series.
To calculate the check sum, add the bytes starting with the byte after BYTE
COUNT (LOW) and ending with the byte before CHECK SUM, take the binary
complement, and set bit 7 to 0.
CHECK SUM = (-sum)&0x7F
Bulk Dumps can be received at any time, and can be transmitted at any time
when a Bulk Dump Request is received.
A Bulk Dump is transmitted on the [Rx CH] channel in response to a Bulk Dump
Request.
STATUS 11110011 F3
Song select
Song number 0sssssss ss
Song number (0-127)
STATUS 11111000 F8
Timing clock
STATUS 11111110 FE
Active sensing
STATUS 11111111 FF
System reset
STATUS 11110000 F0
System exclusive message
ID No. 01111111 7F
Real time System exclusive
Device ID 0ddddddd dd
Destination (00-7E, 7F:all call)
COMMAND 00000110 06
Machine Control Command(MCC) sub-id
00000001 01
Stop(MCS)
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01111111 7F
Real time System exclusive
Device ID 0ddddddd dd
Destination (00-7E, 7F:all call)
COMMAND 00000110 06
Machine Control Command(MCC) sub-id
00000010 02
Play(MCS)
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01111111 7F
Real time System exclusive
Device ID 0ddddddd dd
Destination (00-7E, 7F:all call)
COMMAND 00000110 06
Machine Control Command(MCC) sub-id
00000011 03
Deferred Play(MCS)
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01111111 7F
Real time System exclusive
Device ID 0ddddddd dd
Destination (00-7E, 7F:all call)
COMMAND 00000110 06
Machine Control Command(MCC) sub-id
00000110 06
Record strobe
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01111111 7F
Real time System exclusive
Device ID 0ddddddd dd
Destination (00-7E, 7F:all call)
COMMAND 00000110 06
Machine Control Command(MCC) sub-id
00001001 09
Pause(MCS)
EOX 11110111 F7
End of exclusive
Command rx/tx Function
F0 43 0n 3E cc cc 19 mm ... mm dd
dd ... ee F7
rx/tx
BULK DUMP DATA
F0 43 2n 3E 19 mm ... mm dd dd F7 rx
BULK DUMP REQUEST
Module Name(mm) Data Number(dd)
SCENE LIB “SCENE___” *1) *15) *16) *17)
INPUT EQ LIB “INEQ____” *2) *7) *8)
OUTPUT EQ LIB “OUTEQ___” *3) *9) *10) *11)
Dynamics LIB “DYNA____” *4) *7) *8) *9) *10) *11) *22) *23)
INPUT CH LIB “INCHNNL_” *18) *7) *8)
OUTPUT CH LIB “OUTCHNNL” *19) *9) *10) *11)
GEQ LIB “GEQ_____” *5) *12)
8BandPEQ LIB “8PEQ____” *13)
EFFECT LIB “EFFECT__” *6) *14)
Premium Effect “PEFFECT_” *20)
Portico5033 LIB “P5033___ *21)
Portico5043 LIB “P5043___” *21)
Portico5045 LIB P5045____” *21)
U76 LIB “U76_____” *21)
Opt-2A LIB “OPT-2A__” *21)
EQP-1A LIB “EQ-1A___” *21)
DynamicEQ LIB “DYNAEQ__” *21)
Buss Comp 369 LIB “BSCMP369” *21)
MBC4 LIB “MBC4____” *21)
Dante Input Patch LIB “DANTEIN_” *24)
Mixer Setup “MIXERSET” Fix (512)
Outport Setup “OUT_PORT Fix (512)
Monitor Setup “MONITOR_” Fix (512)
MIDI Setup “MIDI_SET” Fix (512)
Lib Number “LIB_NUM_” Fix (512)
Program Change Table “PRGMCHG_” Fix (512)
Control Change Table “CTRLCHG_” Fix (512)
Preference (Current) “PREF_CUR” Fix (512)
Preference (Admin) “PREF_ADM” Fix (512)
Preference (Guest) “PREF_GST Fix (512)
User Defined Keys (Current) “UDEF_CUR” Fix (512) include Knob, Encoder
User Defined Keys (Admin) “UDEF_ADM” Fix (512) include Knob, Encoder
User Defined Keys (Guest) “UDEF_GST” Fix (512) include Knob, Encoder
Custom Fader Bank (Current) “CFAD_CUR” Fix (512)
Custom Fader Bank (Admin) “CFAD_ADM” Fix (512)
Custom Fader Bank (Guest) “CFAD_GST” Fix (512)
User Level (Current) “UKEY_CUR” Fix (512)
User Level (Guest) “UKEY_GST” Fix (512)
Module Name(mm) Data Number(dd)
Data List
39
In the data portion, seven words of 8-bit data are converted into eight words of
7-bit data.
[Conversion from actual data to bulk data]
d[0-6]: actual data
b[0-7]: bulk data
b[0] = 0;
for( I=0; I<7; I++){
if( d[I]&0x80){
b[0] |= 1<<(6-I);
}
b[I+1] = d[I]&0x7F;
}
[Recovery from bulk data to actual data]
d[0-6]: actual data
b[0-7]: bulk data
for( I=0; I<7; I++){
b[0] <<= 1;
d[I] = b[I+1]+(0x80&b[0]);
}
3.3 PARAMETER CHANGE
Reception
This message is echoed if [PARAMETER CHANGE ECHO] is ON.
This message is received if [PARAMETER CHANGE Rx] is ON and [Rx CH] matches
the Device number included in the SUB STATUS. When a PARAMETER CHANGE is
received, the specified parameter will be controlled. When a PARAMETER
REQUEST is received, the current value of the specified parameter will be
transmitted as a PARAMETER CHANGE with its Device Number as the [Rx CH].
Transmission
If [PARAMETER CHANGE Tx] is ON, and you edit a parameter for which
CONTROL CHANGE transmission has not been enabled, a PARAMETER CHANGE
will be transmitted with the [Tx CH] as its device number.
In response to a PARAMETER REQUEST, a PARAMETER CHANGE will be
transmitted with [Rx CH] as its device number.
4 PARAMETER CHANGE details
4.1 CURRENT SCENE, SETUP, BACKUP, USER SETUP
4.1.1 Format (PARAMETER CHANGE)
Reception
Data will be received when [PARAMETER CHANGE Rx] is on and the Device
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
The corresponding parameter will be changed immediately the data is received.
Transmission
Data will be transmitted with the [Device Number] in [Tx CH] when [PARAMETER
CHANGE Tx] is on and the parameter is not registered on the [CONTROL
CHANGE EVENT LIST].
4.1.2 Format (PARAMETER REQUEST)
Reception
Data will be received when [PARAMETER CHANGE Rx] is on and the Device
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
The corresponding parameter will be changed via PARAMETER CHANGE
immediately the data is received.
4.1.3 Data category
4.2 FUNCTION CALL - LIBRARY STORE, RECALL -
4.2.1 Format (PARAMETER CHANGE)
Reception
Data will be received when [PARAMETER CHANGE Rx] is on and the Device
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
The corresponding parameter will be changed immediately the data is received.
Transmission
Data will be transmitted with the [Device Number] (MIDI CH) in [Tx CH] when
[PARAMETER CHANGE Tx] is on.
4.2.2 Function Name
Command rx/tx Function
F0 43 1n 3E 19 ... F7
RARAMETER CHANGE
rx/tx
CL series native parameter change
F0 43 3n 3E 19 ... F7
PARAMETER REQUEST
rx/tx
CL series native parameter request
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA Category 0ccccccc cc
DATA 0eeeeeee eh
Element no High.
0eeeeeee el
Element no Low.
0iiiiiii ih
Index no High.
0iiiiiii il
Index no Low.
0ccccccc ch
Channel no High.
0ccccccc cl
Channel no Low.
0ddddddd dd
Data
::
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0011nnnn 3n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA Category 0ccccccc cc
DATA 0eeeeeee eh
Element no High.
0eeeeeee el
Element no Low.
0iiiiiii ih
Index no High.
0iiiiiii il
Index no Low.
0ccccccc ch
Channel no High.
0ccccccc cl
Channel no Low.
EOX 11110111 F7
End of exclusive
Data Category Name
0x01 00000001
Current Scene /Setup/Backup/
User Setup Data
0x41 01000001
Premium Rack Data
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 “L”
(ASCII CODE)
01101001 “i”
(ASCII CODE)
01100010 “b”
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0nnnnnnn nh
Number High
0nnnnnnn nl
Number Low
0ccccccc ch
Channel High
0ccccccc cl
Channel Low
EOX 11110111 F7
End of exclusive
Function Name
Store “LibStr__”
Recall “LibRcl__”
Unknown Factor Store “LibUnStr”
Unknown Factor Recall “LibUnRcl”
Store Undo (only Score) “LibStrUd”
Recall Undo (only Scene) “LibRclUd”
Data List
40
4.2.3 Module Name
*1) 0:CH1 - 71:CH72
72:ST IN 1L - 87:ST IN 8R
*2) 256:MIX 1 - 279:MIX 24
*3) 512:MATRIX 1 - 519: MATRIX 8
*4) 1024:STEREO L - 1026:STEREO C
*5) 512: will be used if the recalling or storing data is only one.
*6) 0: GEQ1A, 1: GEQ1B, 2: GEQ2A, ... 36: GEQ19A, 37:GEQ19B
38: EFFECT GEQ1A, 39: EFFECT GEQ1B,
40: EFFECT GEQ2A, ... 52: EFFECT GEQ8A, 53: EFFECT GEQ8B
*7) 0:Effect1- 7:Effect8
*8) 1280:CH1 - 1351:CH72
1352:ST IN 1L - 1367:ST IN 8R
*9) 0: Premium Rack 1A, 1: Premium Rack 1B,
2: Premium Rack 2A, ... 14: Premium Rack 8A, 15: Premium Rack 8B
4.3 FUNCTION CALL - LIBRARY EDIT -
4.3.1 Format (PARAMETER CHANGE)
Reception
Data will be received when [PARAMETER CHANGE Rx] is on and the Device
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
The corresponding memory/library will be changed immediately the data is
received.
Transmission
PARAMETER CHANGE will be sent in reply to Request.
If [PARAMETER CHANGE ECHO] is on, the message will be sent as it is.
4.3.2 Function Name
4.3.3 Module Name
Module Name
Scene “SCENE___”
Input EQ “INEQ____”
Output EQ “OUTEQ___”
Dynamics “DYNA____”
Input CH “INCHNNL_”
Output CH “OUTCHNNL”
GEQ “GEQ_____”
8BandPEQ “8PEQ____”
Effect “EFFECT__”
Portico5033 “P5033___”
Portico5043 “P5043___”
Portico5045 “P5045____”
U76 “U76_____”
Opt-2A “OPT-2A__”
EQP-1A “EQ-1A___”
Dynamic EQ “DYNAEQ__”
Buss Comp 369 “BSCMP369”
MBC4 “MBC4____”
Dante Input Patch “DANTEIN_”
Function Number Channel*1) tx/rx
“LibStr__” SCENE 1-300 *5)
tx/rx
INPUT EQ LIB 41-199 *1)
tx/rx
OUTPUT EQ LIB 4-199 *2) *3) *4)
tx/rx
Dynamics LIB 42-199 *1) *2) *3) *4) *8)
tx/rx
INPUT CH LIB 1-199 *1)
tx/rx
OUTPUT CH LIB 1-199 *2) *3) *4)
tx/rx
GEQ LIB 1-199 *6)
tx/rx
8BandPEQ LIB 1-199 *6)
tx/rx
EFFECT LIB 28-199 *7)
tx/rx
Premium Effect LIB 1-100 *9)
tx/rx
Dante Input Patch LIB 1-10 *5)
tx/rx
“LibUnStr” SCENE 1-300 0
tx
INPUT EQ LIB 41-199 0
tx
OUTPUT EQ LIB 4-199 0
tx
Dynamics LIB 42-199 0
tx
INPUT CH LIB 1-199 0
tx
OUTPUT CH LIB 1-199 0
tx
GEQ LIB 1-199 0
tx
8BandPEQ LIB 1-199 0
tx
EFFECT LIB 28-199 0
tx
Premium Effect LIB 1-100 0
tx
Dante Input Patch LIB 1-10 0
tx
“LibRcl__” SCENE 0-300 *5)
tx/rx
INPUT EQ LIB 1-199 *1)
tx/rx
OUTPUT EQ LIB 1-199 *2) *3) *4)
tx/rx
Dynamics LIB 1-199 *1) *2) *3) *4) *8)
tx/rx
INPUT CH LIB 0-199 *1)
tx/rx
OUTPUT CH LIB 0-199 *2) *3) *4)
tx/rx
GEQ LIB 0-199 *6)
tx/rx
8BandPEQ LIB 1-199 *6)
tx/rx
EFFECT LIB 1-199 *7)
tx/rx
Premium Effect LIB 0-100 *9)
tx/rx
Dante Input Patch LIB 0-10 *5)
tx/rx
“LibUnRcl” SCENE 0 *5)
tx
INPUT EQ LIB 0 *1)
tx
OUTPUT EQ LIB 0 *2) *3) *4)
tx
Dynamics LIB 0 *1) *2) *3) *4) *8)
tx
INPUT CH LIB 0 *1)
tx
OUTPUT CH LIB 0 *2) *3) *4)
tx
GEQ LIB 0 *6)
tx
8BandPEQ LIB 0 *6)
tx
EFFECT LIB 0 *7)
tx
Premium Effect LIB 0 *9)
tx
Dante Input Patch LIB 0 *5)
tx
“LibStrUd” SCENE 0 0
“LibRclUd” SCENE 0 0
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 “L”
(ASCII CODE)
01101001 “i”
(ASCII CODE)
01100010 “b”
(ASCII CODE)
Function Number Channel*1) tx/rx
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
0fffffff ff
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0sssssss sh
number -source start High
0sssssss sl
number -source start Low
0eeeeeee eh
number -source end High
0eeeeeee el
number -source end Low
0ddddddd dh
number -destination start High
0ddddddd dl
number -destination to start Low
EOX 11110111 F7
End of exclusive
Function Name
Copy “LibCpy__”
Paste “LibPst__”
Clear “LibClr__”
Cut “LibCut__”
Insert “LibIns__”
Edit Undo “LibEdtUd”
Module Name Function
SCENE LIB “SCENE___” Copy, Paste, Clear, Cut, Insert, EditUndo
INPUT EQ LIB “INEQ____” Clear Only
OUTPUT EQ LIB “OUTEQ___” Clear Only
Dynamics LIB “DYNA____” Clear Only
INPUT CH LIB “INCHNNL_” Clear Only
OUTPUT CH LIB “OUTCHNNL” Clear Only
GEQ LIB “GEQ_____” Clear Only
8BandPEQ LIB “8PEQ____” Clear Only
EFFECT LIB “EFFECT__ Clear Only
Portico5033 LIB “P5033___” Clear Only
Portico5043 LIB “P5043___” Clear Only
Portico5045 LIB “P5045____” Clear Only
U76 LIB “U76_____” Clear Only
Opt-2A LIB “OPT-2A__ Clear Only
EQP-1A LIB “EQ-1A___” Clear Only
DynamicEQ LIB “DYNAEQ__” Clear Only
Buss Comp 369 LIB “BSCMP369” Clear Only
MBC4 LIB “MBC4____” Clear Only
Dante Input Patch LIB “DANTEIN_” Clear Only
Data List
41
4.4 FUNCTION CALL - LIBRARY ATTRIBUTE -
4.4.1 Format (PARAMETER CHANGE)
Reception
Data will be received when [PARAMETER CHANGE Rx] is on and the Device
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
When the message is received, the title of the specified memory/library will be
edited.
Transmission
PARAMETER CHANGE will be sent in reply to Request.
If [PARAMETER CHANGE ECHO] is on, the message will be sent as it is.
4.4.2 Format (PARAMETER REQUEST)
Reception
The PARAMETER CHANGE will be sent with Device number [Rx CH] immediately
the data is received.
4.4.3 Module Name
4.5 EXIST LIBRARY RANGE
4.5.1 Format (PARAMETER CHANGE)
Transmission
When CL series receives Library Exist request command from outside, the answer
will be sent back with the following Parameter change.
This packet shows smallest library number range that exists and not read only.
Top number is requested number or more.
-Example-
SCENE is stored 5,6,7,10,100 and 101
Request Number: 0
Data : Valid, Top Number : 5, End Number 7
Request Number: 8
Data : Valid, Top Number : 10, End Number 10
Request Number: 11
Data : Valid, Top Number : 100, End Number 101
Request Number: 102
Data : Invalid, Top Number : 0, End Number 0
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 “L”
(ASCII CODE)
01101001 “i”
(ASCII CODE)
01100010 “b”
(ASCII CODE)
01000001 “A”
(ASCII CODE)
01110100 “t”
(ASCII CODE)
01110010 “r”
(ASCII CODE)
01100010 “b”
(ASCII CODE)
01110100 “t”
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0nnnnnnn nh
Scene/Library number High
0nnnnnnn nl
Scene/Library number Low
0eeeeeee eh
Element High
0eeeeeee el
Element Low
0iiiiiii ih
Index High
0iiiiiii il
Index Low
0ccccccc ch
Channel High
0ccccccc cl
Channel Low
0000dddd dd
Data28~31bit
0ddddddd dd
Data21~27bit
0ddddddd dd
Data14~20bit
0ddddddd dd
Data7~13bit
0ddddddd dd
Data0~6bit
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0011nnnn 3n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 “L”
(ASCII CODE)
01101001 “i”
(ASCII CODE)
01100010 “b”
(ASCII CODE)
01000001 “A”
(ASCII CODE)
01110100 “t”
(ASCII CODE)
01110010 “r”
(ASCII CODE)
01100010 “b”
(ASCII CODE)
01110100 “t”
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0nnnnnnn nh
Scene/Library number High
0nnnnnnn nl
Scene/Library number Low
0eeeeeee eh
Element High
0eeeeeee el
Element Low
0iiiiiii ih
Index High
0iiiiiii il
Index Low
0ccccccc ch
Channel High
0ccccccc cl
Channel Low
EOX 11110111 F7
End of exclusive
Module Name Number
SCENE LIB “SCENE___” 0-300 (0:response only)
INPUT EQ LIB “INEQ____” 1-200 (1-40:response only)
OUTPUT EQ LIB “OUTEQ___” 1-200 (1-3:response only)
Dynamics LIB “DYNA____” 1-200 (1-41:response only)
INPUT CH LIB “INCHNNL_” 0-200 (0:response only)
OUTPUT CH LIB “OUTCHNNL” 0-200 (0:response only)
GEQ LIB “GEQ_____” 0-200 (0:response only)
8BandPEQ LIB “8PEQ____” 0-199 (0:response only)
EFFECT LIB “EFFECT__” 1-200 (1-27:response only)
Portico5033 LIB “P5033___” 0-100 (0:response only)
Portico5043 LIB “P5043___” 0-100 (0:response only)
Portico5045 LIB “P5045____” 0-100 (0:response only)
U76 LIB “U76_____” 0-100 (0:response only)
Opt-2A LIB “OPT-2A__” 0-100 (0:response only)
EQP-1A LIB “EQ-1A___” 0-100 (0:response only)
DynamicEQ LIB “DYNAEQ__” 0-100 (0:response only)
Buss Comp 369 LIB “BSCMP369” 0-100 (0:response only)
MBC4 LIB “MBC4____” 0-100 (0:response only)
Dante Input Patch LIB “DANTEIN_” 0-10 (0:response only)
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 “L”
(ASCII CODE)
01101001 “i”
(ASCII CODE)
01100010 “b”
(ASCII CODE)
01000101 “E”
(ASCII CODE)
01111000 “x”
(ASCII CODE)
01101001 “i”
(ASCII CODE)
01110011 “s”
(ASCII CODE)
01110100 “t”
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0sssssss ss
Data Status ( 0:Invalid data,1:Valid Data )
0nnnnnnn nh
Request Number High
0nnnnnnn nl
Request Number Low
0ttttttt th
Top Number High
0ttttttt tl
Top Number Low
0eeeeeee eh
End Number High
0eeeeeee el
End Number Low
EOX 11110111 F7
End of exclusive
Module Name Number
Data List
42
4.5.2 Format (PARAMETER REQUEST)
Reception
The PARAMETER CHANGE will be sent with Device number [Rx CH] immediately
the data is received.
4.5.3 Module Name
4.6 FUNCTION CALL - COLLECTION STORE -
4.6.1 Format (PARAMETER CHANGE)
Transmission
Data will be transmitted with the [Device Number] in [Tx CH] when [PARAMETER
CHANGE Tx] is on.
4.6.2 Function Name
4.6.3 Module Name
4.7 FUNCTION CALL - MODULE -
4.7.1 Format (PARAMETER CHANGE)
Reception
Data will be received when [PARAMETER CHANGE Rx] is on and the Device
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
The corresponding effect will function immediately the data is received
(depending on the effect type).
4.7.2 Module Name
This will not work when the Effect Type is different.
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0011nnnn 3n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 “L”
(ASCII CODE)
01101001 “i”
(ASCII CODE)
01100010 “b”
(ASCII CODE)
01000101 “E”
(ASCII CODE)
01111000 “x”
(ASCII CODE)
01101001 “i”
(ASCII CODE)
01110011 “s”
(ASCII CODE)
01110100 “t”
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0nnnnnnn nh
Request Number High
0nnnnnnn nl
Request Number Low
EOX 11110111 F7
End of exclusive
Module Name Number
SCENE LIB “SCENE___” 1-300
INPUT EQ LIB “INEQ____” 41-200
OUTPUT EQ LIB “OUTEQ___” 4-200
Dynamics LIB “DYNA____” 42-200
INPUT CH LIB “INCHNNL_” 1-200
OUTPUT CH LIB “OUTCHNL” 1-200
GEQ LIB “GEQ_____” 1-200
8BandPEQ LIB “8PEQ____” 1-199
EFFECT LIB “EFFECT__” 55-200
Portico5033 LIB “P5033___” 1-100
Portico5043 LIB “P5043___” 1-100
Portico5045 LIB “P5045____” 1-100
U76 LIB “U76_____” 1-100
Opt-2A LIB “OPT-2A__ 1-100
EQP-1A LIB “EQ-1A___” 1-100
DynamicEQ LIB “DYNAEQ__” 1-100
Buss Comp 369 LIB “BSCMP369” 1-100
MBC4 LIB “MBC4____” 1-100
Dante Input Patch LIB “DANTEIN_” 1-10
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001100 “C”
(ASCII CODE)
01101001 “o”
(ASCII CODE)
01100010 “l”
(ASCII CODE)
01010101 “U”
(ASCII CODE)
01101110 “n”
(ASCII CODE)
01010011 “S”
(ASCII CODE)
01110100 “t”
(ASCII CODE)
01110010 “r”
(ASCII CODE)
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0nnnnnnn nh
Number High
0nnnnnnn nl
Number Low
0ccccccc ch
Channel High
0ccccccc cl
Channel Low
EOX 11110111 F7
End of exclusive
Function Number tx/rx
“ColUnStr” Setup 0
tx
User Defined Key 0
tx
Program Change 0
tx
Control Change 0
tx
Module Name
Mixer Setting “MIXERSET”
Outport Setting “OUT_PORT”
Monitor Setting “MONITOR_”
MIDI Setting “MIDI_SET”
Lib Number “LIB_NUM_”
Program Change Table “PRGMCHG_”
Control Change Table “CTRLCHG_”
Preference (Current) “PREF_CUR”
Preference (Admin) “PREF_ADM”
Preference (Guest) “PREF_GST”
User Defined Keys (Current) “UDEF_CUR”
User Defined Keys (Admin) “UDEF_ADM”
User Defined Keys (Guest) “UDEF_GST”
Custom Fader Bank (Current) “CFAD_CUR”
Custom Fader Bank (Admin) “CFAD_ADM”
Custom Fader Bank (Guest) “CFAD_GST”
User Level (Current) “UKEY_CUR”
User Level (Guest) “UKEY_GST”
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01001101 “M”
01101111 “o”
01100100 “d”
01000110 “F”
01111000 “x”
01010100 “T”
01110010 “r”
01100111 “g”
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0eeeeeee ee
Effect number (0:RACK1-7:RACK8)
0ppppppp pp
Release:0, Press:1
EOX 11110111 F7
End of exclusive
Module Name Number
Freeze Play button “FRZPLAY_” 0:RACK1, 2:RACK3, 4:RACK5, 6:RACK7
Freeze Record button “FRZREC__” 0:RACK1, 2:RACK3, 4:RACK5, 6:RACK7
Module Name
Data List
43
4.8 FUNCTION CALL - CHANNEL -
4.8.1 Pair ON/OFF Trigger Format (PARAMETER CHANGE)
Reception
Data will be received when [PARAMETER CHANGE Rx] is on and the Device
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
4.8.2 Module Name
*1) 0:CH1 - 71:CH72
256:MIX 1 - 279:MIX 24
512:MATRIX 1-519:MATRIX 8
4.9 LEVEL METER DATA
4.9.1 Format (PARAMETER CHANGE)
When transmission is enabled by receiving Request for Level Meter, the
corresponding metering data will be sent in every 50 millisecond for 10 seconds.
If metering information is expected to be continuously sent, Request is needed to
be sent in at least every 10 seconds.
Reception
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
Transmission
When transmission is enabled by receiving Request, the corresponding metering
data will be sent in constant interval for a given period of time (The interval and
time will vary depending on devices).
When rebooted or port setting is changed, the transmission will be disabled.
When [PARAMETER CHANGE ECHO] is on, the message will be sent as it is.
4.9.2 Format (PARAMETER REQUEST)
Reception
Data will be received when [PARAMETER CHANGE Rx] is on and the Device
number of both [Rx CH] and SUB STATUS match.
The data will be echoed when [PARAMETER CHANGE ECHO] is on.
The corresponding metering data will be sent via [Rx CH] in constant interval for
a given period of time (The interval and time will vary depending on devices).
If this is received with an Address UL = 0x7F, transmission of all meter data will
stop (will be disabled) immediately.
Transmission
When [PARAMETER CHANGE ECHO] is on, the message will be sent as it is.
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00000000 00
OTHER DATA
FUNCTION NAME 01000011 “C”
01101000 “h”
01101100 “l”
01010000 “P”
01101001 “i”
01110010 “r”
01000011 “C”
01110000 “p”
MODULE NAME 0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
0mmmmmmm mm
(ASCII CODE)
DATA 0sssssss sh
Source Channel Number H *1)
0sssssss sl
Source Channel Number L *1)
0ddddddd dh
Destination Channel Number H *1)
0ddddddd dl
Destination Channel Number L *1)
EOX 11110111 F7
End of exclusive
Module Name
Pair On (with Copy) “PAIRONCP”
Pair On (with Reset Both) “PAIRONRS”
Pair Off “PAIROFF_”
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00100001 21
REMOTE LEVEL METER
DATA 0mmmmmmm mm
ADDRESS UL
0mmmmmmm mm
ADDRESS LU
0mmmmmmm mm
ADDRESS LL
0ddddddd dd
Data1
::
EOX 11110111 F7
End of exclusive
STATUS 11110000 F0
System exclusive message
ID No. 01000011 43
Manufacturer's ID number (YAMAHA)
SUB STATUS 0011nnnn 3n
n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E
Digital mixer
MODEL ID 00011001 19
CL Series
DATA CATEGORY 00100001 21
REMOTE LEVEL METER
DATA 0mmmmmmm mm
ADDRESS UL
0mmmmmmm mm
ADDRESS LU
0mmmmmmm mm
ADDRESS LL
0ccccccc ch
Count H
0ccccccc cl
Count L
EOX 11110111 F7
End of exclusive
Data List
44
Input/Output Characteristics
Analog input characteristics
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal
output level when the unit is set to maximum gain. (all faders and level controls are
maximum position.)
*2. XLR-3-31 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
* In these specifications, 0dBu= 0.775 Vrms.
* All input AD converters are 24bit linear, 128times oversampling.
* +48V DC ( phantom power ) is supplied to ONI IN (1-8) and TALKBACK XLR type
connectors via each individual software controlled switches.
Analog output characteristics
*1. XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
*2. PHONES stereo phone jack is unbalanced. (Tip= LEFT, Ring= RIGHT, Sleeve= GND)
*3. There are switches inside the body to preset the maximum output level.
*4. The position of the level control is 10dB lowered from Max.
* In these specifications, 0dBu= 0.775 Vrms.
* All output DA converters are 24bit, 128times oversampling.
Digital input & output characteristics
Digital output characteristics
*1. Channel Status of DIGITAL OUT
*2. XLR-3-32 type connectors are balanced. (1= GND, 2= HOT, 3= COLD)
Input
Terminals
GAIN
Actual
Load
Impedance
For Use
With
Nominal
Input Level
Connector
Sensitivity
*1
Nominal
Max. before
clip
OMNI IN
1-8
+66dB
7.5kΩ
50-600Ω
Mics &
600Ω
Lines
-82dBu
(61.6μV)
-62dBu
(0.616mV)
-42dBu
(6.16mV)
XLR-3-31 type
(Balanced)
*2
-6dB
-10dBu
(245mV)
+10dBu
(2.45V)
+30dBu
(24.5V)
TALKBACK
+64dB
10kΩ
50-600Ω
Mics &
600Ω
Lines
-70dBu
(0.245mV)
-60dBu
(0.775mV)
-40dBu
(7.75mV)
XLR-3-31 type
(Balanced)
*2
+20dB
-26dBu
(38.8mV)
-16dBu
(0.123V)
+4dBu
(1.23V)
Output
Terminals
Actual
Source
Impedance
For Use
With
Nominal
GAIN
SW
*3
Output Level
Connector
Nominal
Max. before
clip
OMNI
OUT 1-8
75Ω
600Ω
Lines
+24dB
(default)
+4dBu
(1.23V)
+24dBu
(12.3V)
XLR-3-32 type
(Balanced)
*1
+18dB
-2dBu
(616mV)
+18dBu
(6.16V)
PHONES 15Ω
Phones
-
75mW
*4
150mW
Stereo Phone Jack
(TRS)
(Unbalanced)
*2
40Ω
Phones
-
65mW
*4
150mW
Terminal Format
Data
length
Level Audio Connector
Primary/
Secondary
Dante
24bit or
32bit
1000Base
-T
64ch Input/64ch Output
@48kHz
EtherCON Cat5e
Terminal Format
Data
Length
Level Connector
DIGITAL
OUT
*1
AES/EBU
AES/EBU Professional Use
24bit RS422
XLR-3-32 type (Balanced)
*2
Byte Bit Field Name Fixed/Variable Data Description
0
0 Block Format
fixed
1 professional use
1Mode 0 audio
2-4 Emphasis 0x4 off
5 Fs Lock 0 lock
6-7 Sampling Frequency variable
0x0 others
0x3 32 kHz
0x2 44.1 kHz
0x1 48 kHz
1
0-3 Channel Mode
fixed
0x1 2ch mode
4-7 Users Bit Management 0x0 -
2
0-2 Use of AUX
fixed
0x1 24 bits Audio Data
3-7 Source 0x00 -
3 0-7 Multi Channel fixed 0x00 -
4
0-1 Digital Audio Reference Signal
fixed
0x0
-
2- 0
3-6 Sampling Frequency variable 0x0 others
7 Sampling Frequency Scan Flag fixed 0 -
Data List
45
I/O SLOT (1-3) characteristics
Each I/O Slot accepts a mini-YGDAI card. Only Slot1 has a serial interface.
Control I/O characteristics
*1. Input pin: TTL level, w/ internal pull-up (47kΩ)
Output pin: Open drain output (Vmax=12V, maximum sink current/pin=75mA)
Power supply pin: Output voltage Vp=5V, Max. output current Imax=300mA
*2. 4 pin=+12V, 3 pin=GND, Lamp rating 5W. Voltage control by software.
Terminal Format Level Connector
MIDI
IN MIDI - DIN Connector 5P
OUT MIDI - DIN Connector 5P
WORD
CLOCK
IN - TTL/75Ω terminated BNC Connector
OUT - TTL/75Ω BNC Connector
GPI (5IN/5OUT) - -
D Sub Connector 15P
(Female)
*1
NETWORK IEEE802.3 10BASE-T/100Base-TX RJ-45
LAMP (CL5: x3, CL3:
x2, CL1: x1)
-
0V-12V
*2
XLR-4-31 type
*2
USB HOST USB 2.0 - USB A Connector (Female)
DC POWER INPUT - - JL05 Connector
METER (CL3/CL1 only) - -
D Sub Connector 9P
(Female)
Data List
46
Electrical Characteristics
All faders are nominal when measured. Output impedance of signal generator:150ohms
Frequency Response. Fs= 44.1 kHz or 48 kHz @20 Hz-20 kHz, referenced to
the nominal output level @1 kHz
Total Harmonic Distortion. Fs= 44.1 kHz or 48 kHz
* Total Harmonic Distortion is measured with a 18 dB/octave filter @80 kHz
Hum & Noise. Fs= 44.1 kHz or 48 kHz, EIN= Equivalent Input Noise
* Hum & Noise are measured with A-weight filter.
Dynamic Range. Fs= 44.1 kHz or 48 kHz
* Dynamic Range are measured with A-weight filter.
Sampling Frequency
Input Output RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8
OMNI OUT 1-8 600 Ω
GAIN: +66dB
-1.5 0.0 0.5
dB
PHONES 8 Ω -3.0 0.0 0.5
Input Output RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600 Ω
+4 dBu @20 Hz-20 kHz, GAIN: +66dB 0.1
%
+4 dBu @20 Hz-20 kHz, GAIN: -6dB 0.05
Internal OSC
OMNI OUT 1-8 600 Ω Full Scale Output @1 kHz 0.02
PHONES 8 Ω
Full Scale Output @1 kHz, PHONES Level
Control: Max.
0.2
Input Output RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600 Ω
Rs= 150 Ω, GAIN: +66dB
Master fader at nominal level and one
Ch fader at nominal level.
-128
EIN
dBu
-62
Rs= 150 Ω, GAIN: -6dB
Master fader at nominal level and one
Ch fader at nominal level.
-84 -79
All INPUTs OMNI OUT 1-8 600 Ω
Rs= 150 Ω, GAIN: -6dB
Master fader at nominal level and all
OMNI IN 1-8 in faders at nominal level.
-70
- OMNI OUT 1-8 600 Ω Residual Output Noise, ST Master Off -88
-PHONES 8 Ω
Residual Output Noise, PHONES Level
Control Min.
-88
Input Output RL Conditions Min. Typ. Max. Unit
OMNI IN 1-8 OMNI OUT 1-8 600 Ω AD + DA, GAIN: -6dB 108 dB
- OMNI OUT 1-8 600 Ω DA Converter 112 dB
Parameter Conditions Min. Typ. Max. Unit
External Clock
Frequency
Range
Fs= 44.1 kHz
Fs= 45.9375 kHz (44.1 kHz +4.1667%)
Fs= 44.1441 kHz (44.1 kHz +0.1%)
Fs= 44.0559 kHz (44.1 kHz -0.1%)
Fs= 42.336 kHz (44.1 kHz -4.0%)
-200 +200 ppm
Fs= 48 kHz
Fs= 50 kHz (48 kHz +4.1667%)
Fs= 48.048 kHz (48 kHz +0.1%)
Fs= 47.952 kHz (48 kHz -0.1%)
Fs= 46.080 kHz (48 kHz -4.0%)
Jitter of PLL
DIGITAL IN Fs= 44.1 kHz
DIGITAL IN Fs= 48 kHz
10 ns
Internal Clock
Frequency
Word Clock : Int 44.1 kHz 44.1
kHz
Word Clock : Int 48 kHz 48
Accuracy
Word Clock : Int 44.1 kHz
-50 +50 ppm
Word Clock : Int 48 kHz
Jitter
Word Clock : Int 44.1 kHz 4.429
ns
Word Clock : Int 48 kHz 4.069
Data List
47
Mixer Basic Parameters
Libraries
Input Function
Output Function
Output Port
Processor
Name Number Total
Scene Memory Preset 1 + User 300 301
Input CH Library Preset 1 + User 199 200
Output CH Library Preset 1 + User 199 200
Input EQ Library Preset 40 + User 159 199
Output EQ Library Preset 3 + User 196 199
Dynamics Library Preset 41 + User 158 199
Effect Library Preset 27 + User 172 199
GEQ Library Preset 1 + User 199 200
Premium Rack Library
Portico5033
Portico5043
Portico5045
U76
Opt-2A
EQ-1A
Dynamic EQ
Buss Comp 369
MBC4
Preset 1 + User 199 200
Dante Input Patch Library Preset 1 + User 10 11
Function Parameter
Phase Normal/Reverse
Digital Gain -96 dB to +24 dB
L,R-MONO L-MONO/R-MONO/LR-MONO/STEREO IN
HPF
Slope= -12dB/Oct, -6dB/Oct
Frequency= 20 Hz to 600 Hz
Attenuator -96 dB to 0 dB
4 Band
Equalizer
Frequency= 20 Hz to 20 kHz
Gain= -18 dB to +18 dB
Q= 0.10 to 10.0
Low Shelving (Low Band)
High Shelving, LPF (High Band)
PRECISE, AGGRESSIVE, SMOOTH, LEGACY(Type I/Type II)
Insert Insert Point: Pre EQ/Pre Fader/Post On
Direct Out Direct Out Point: Pre HPF/Pre EQ/Pre Fader/Post On
Dynamics 1
Type: Gate/Ducking/Comp/Expander
Threshold=Gate: -72 dB to 0 dB
Others: -54 dB to 0 dB
Ratio= 1:1 to ∞:1
Attack= 0 msec to 120 msec
Hold= 48 kHz: 0.02 msec to 1.96 sec
44.1 kHz: 0.02 msec to 2.13 sec
Dynamics 1
Decay= 48 kHz: 5 msec to 42.3 sec
44.1 kHz: 6 msec to 46.1 sec
Releace= 48 kHz: 5 msec to 42.3 sec
44.1 kHz: 6 msec to 46.1 sec
Range= Gate: -∞ dB to 0 dB
Ducking: -70 dB to 0 dB
Gain= 0.0 dB to +8dB
Knee= Hard to 5 (soft)
Key In: Self Pre EQ/Self Post EQ/Mix Out21-24
Ch1-STIN8R (8ch block)
Key In Filter: HPF/LPF/BPF
Dynamics2
Type: Comp/De-Esser/Compander H/Compander S
Threshold= -54 dB to 0 dB
Ratio= 1:1 to ∞:1
Compander: 1:1 to 20:1
Attack= 0 msec to 120 msec
Release= 48 kHz: 5 msec to 42.3 sec
44.1 kHz: 6 msec to 46.1 sec
Gain= -18 dB to 0 dB, 0 dB to +18 dB
Knee= Hard to 5 (soft)
Key In: Self Pre EQ/Self Post EQ/Mix Out21-24
Ch1-STIN8R (8ch block)
Width= 1 dB to 90 dB
Frequency= 1.0 KHz to 12.5KHz
TYPE= HPF, BPF
Q= 0.10 to 10.0
Fader Level: 1024 steps, ∞, -138 dB to +10 dB
On On/Off
Pan/Balance
Position L63 to R63
Pan Mode: Pan/Balance
DCA Group 16 Groups
Mute Group 8 Groups
Mix Send
24 sends
Fix/Variable can be set each two mixes
(Surround Pan can be set 1 to 6 mixes)
Mix Send Point: Pre EQ/Pre Fader/Post On
Level: 1024 steps, ∞, -138 dB to +10 dB
(Position L63 to R63, R63 to F63 for Surround)
Matrix Send
8 Sends
Matrix Send Point: Pre EQ/Pre Fader/Post On
Level: 1024 steps, ∞, -138 dB to +10 dB
LCR Pan CSR= 0% to 100%
DELAY 0 ms to 1000 msec
Function Parameter
Attenuator -96 dB to 0 dB
Function Parameter
4 Band
Equalizer
Frequency= 20 Hz to 20 kHz
Gain= -18 dB to +18 dB
Q= 0.10 to 10.0
Low Shelving (Low Band)
High Shelving, LPF (High Band)
PRECISE, AGGRESSIVE, SMOOTH, LEGACY(Type I/Type
II)
Insert Insert Point: Pre EQ/Pre Fader/Post On
Dynamics 1
Type: Comp/Expander/Compander H/Compander S
Threshold= -54 dB to 0 dB
Ratio= 1:1 to ∞:1
Compander: 1:1 to 20:1
Attack= 0 msec to 120 msec
Release= 48 kHz: 5 msec to 42.3 sec
44.1 kHz: 6 msec to 46.1 sec
Gain= -18 dB to 0 dB, 0 dB to +18 dB
Knee= Hard to 5 (soft)
Key In: Self Pre EQ/Self Post EQ/Mix Out21-24 MIX24/
MTRX1-8/STIN LR/MONO(C) (8ch block)
Width= 1 dB to 90 dB
Fader Level: 1024 steps, ∞, -138 dB to +10 dB
On On/Off
Pan/Balance Position L63 to R63
DCA Group 16 Groups
Mute Group 8 Groups
Mix to Matrix
Stereo to Matrix
Matrix Send Point: Pre Fader/Post On
Level: 1024 steps, ∞, -138 dB to +10 dB
Oscillator
Level= 0 to -96dB (1 dB step)
On/Off= Software control
Function Parameter
Out Port Delay 0 msec to 1000 msec
Out Port Phase Normal/Reverse
Gain -96 to +24 dB
Function Parameter
GEQ 31 bands x 16(24) or 15 bands x 32(48) systems
PEQ (8 bands PEQ + 3 notchs + HPF, LPF) x 32(48) systems
AUTOMIXER 8(16) channels
Effects Stereo In/Stereo Out multi effector x 8 systems
Premium Rack
Parameter
Stereo(Dual) In/Stereo(Dual) Out Premium Rack x
9systems
Function Parameter
Data List
48
Pin Assignment
DC POWER INPUT GPI METER (CL3/CL1 only)
Pin Signal Name Pin Signal Name
1+24V13GND
2+24V14GND
3+24V15GND
4+24V16GND
5+24V17GND
6+24V18GND
7+24V19CAUTION(+)
8 +24V 20 CAUTION(-)
9 +24V 21 DETECT A
10 GND 22 DETECT B
11 GND 23 DETECT GND
12 GND Frame GND
1
2
3
4
5
6789
10111213
14
15
16
17181920
21
22
23
Pin Signal Name Pin Signal Name
1GPO19GPO2
2GPO310GPO4
3GPO511GND
4GND12GND
5 +5V 13 +5V
6 GPI114GPI2
7 GPI315GPI4
8GPI5
91011
8
123
15
Pin Signal Name Pin Signal Name
1 RESET 6 +3.3LD
2 SDA 7 +3.3LD
3 DGND 8 LDGND
4SCL9LDGND
5+3.3D
1
6
5
9
Data List
49
MIDI Implementation Chart
2102 .raM 1 :etaD] elosnoC gnixiM latigiD [ AHAMAY
Model: CL5/CL3/CL1
MIDI Implementation Chart
Version: 1.0
Function... Transmitted Recognized Remarks
Basic
Channel
Default
Changed
1–16
1–16
1–16
1–16
Memorized
Mode
Default
Messages
Altered
X
X
**************
1, 3
X
X
Memorized
Note
Number
True Voice
0–127
X
0–127
X
Velocity
Note On
Note Off
O 9nH, v=0,127
X
O 9nH, v=1-127
O
Effect Control
After
Touch
Key’s
Ch’s
X
X
X
X
Pitch
Bend
XX
Control
Change
0,32
6,38
98,99
1-31,33-95, 102-
119
O
O
O
O
O
O
O
O
Bank Select
Data Entry
NRPN LSB,MSB
Assignable Cntrl
Prog
Change :True#
O 0–127
**************
O 0–127
0–300
Assignable
2*,1* O1* OevisulcxE metsyS
Common
:Song Pos.
:Song Sel.
:Tune
X
X
X
X
O
X
Recorder Control
System
Real Time
:Clock
:Commands
X
X
O
X
Effect Contro
l
Aux
Messages
:All Sound O
ff
:Reset All Cntrls
:Local ON/OFF
:All Notes OFF
:Active Sense
:Reset
X
X
X
X
X
X
X
X
X
X
O
O
Notes
*1 Bulk Dump/Request and Parameter Change/Request.
*2 MMC
Mode 1: OMNI ON, POLY
Mode 3: OMNI OFF, POLY
Mode 2: OMNI ON, MONO
Mode 4: OMNI OFF, MONO
O: Yes
X: No
© 2012 Yamaha Corporation
Published 07/2018 MA-F0
Manual Development Group
Yamaha Downloads
https://download.yamaha.com/
Yamaha Pro Audio global website
https://www.yamaha.com/proaudio/
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337

Yamaha CL1 Manual de usuario

Tipo
Manual de usuario
Este manual también es adecuado para