QFX MPX-1201 Instrucciones de operación

Marca: QFX

Modelo: MPX-1201

Tipo: Instrucciones de operación

MPX-1201

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER ON THIS SPEAKER. THERE ARE NO USER-SERVICEABLE PARTS

INSIDE. REFER ALL SERVICING TO A QUALIFIED TECHNICIAN

To prevent re or electric shock, do not expose this equipment to rain or moisture. Do not store or operate this product near any liquids,

heat sources such as radiators, heat registers. Clean only with a dry cloth. Users should exhibit extra safety when this symbol appears in

this instruction manual and follow all precautions as they are stated.

BATTERY (*Charge and play not supported)

The MPX-1201 is a lithium battery powered PA loudspeaker. Be sure that you have completely charged the battery prior to rst use to

maximize the battery's lifespan. Once the power adaptor is connected to a power source, it will automatically begin charging (it takes 2-3

hours to fully charge the lithium battery). Even if the battery power is low, the unit will power on when connected to a power source.

When the battery is charging, the battery LED is red. When the battery is fully charged, the LED will turn o. After the unit is fully charged,

please disconnect it from the power source. The battery can be recharged roughly 300 times in its lifetime. When not in use, the speaker

should always be set OFF to prevent the unit from draining the battery. If the unit is not used for a prolonged periods of time, the battery

will gradually lose its power. It is recommended to fully charge the battery at least every 60 days.

CHARGE AND PLAY

When the battery power is completely empty, the unit to cannot charge and perform at 100% of the volume when immediately

connected to a power source. It is suggested to charge the unit for a while before using it at 100% volume. The unit will perform and

charge at low volume levels. The volume output will increase as the unit continues to charge.

ADVERTENCIA

PARA REDUCIR EL RIESGO DE DESCARGAS ELÉCTRICAS, NO RETIRE LA CUBIERTA DE ESTE ALTAVOZ. NO HAY PARTES REPARABLES POR EL

USUARIO ADENTRO. CONSULTE TODO EL SERVICIO A UN TÉCNICO CALIFICADO

Para evitar incendios o descargas eléctricas, no exponga este equipo a la lluvia ni a la humedad. No almacene ni opere este producto cerca

de líquidos, fuentes de calor como radiadores, rejillas de calefacción. Limpiar solamente con un paño seco. Los usuarios deben exhibir una

seguridad adicional cuando este símbolo aparezca en este manual de instrucciones y seguir todas las precauciones indicadas.

BATERÍA (* Carga y reproducción no compatibles)

El MPX-1201 es un altavoz de megafonía alimentado por batería de litio. Asegúrese de haber cargado completamente la batería antes del

primer uso para maximizar la vida útil de la batería. Una vez que el adaptador de corriente está conectado a una fuente de alimentación,

comenzará a cargarse automáticamente (la batería de litio tarda entre 2 y 3 horas en cargarse por completo). Incluso si la carga de la

batería es baja, la unidad se encenderá cuando se conecte a una fuente de alimentación. Cuando la batería se está cargando, el LED de la

batería está en rojo. Cuando la batería esté completamente cargada, el LED se apagará. Una vez que la unidad esté completamente

cargada, desconéctela de la fuente de alimentación. La batería se puede recargar aproximadamente 300 veces durante su vida útil.

Cuando no esté en uso, el altavoz siempre debe estar APAGADO para evitar que la unidad agote la batería. Si la unidad no se utiliza

durante períodos prolongados de tiempo, la batería perderá gradualmente su carga. Se recomienda cargar completamente la batería al

menos cada 60 días.

CARGAR Y JUGAR

Cuando la energía de la batería está completamente vacía, la unidad no puede cargarse y funcionar al 100% del volumen cuando se

conecta inmediatamente a una fuente de alimentación. Se sugiere cargar la unidad por un tiempo antes de usarla al 100% del volumen.

La unidad funcionará y se cargará a niveles de volumen bajos. La salida de volumen aumentará a medida que la unidad continúe

cargándose.

AVERTISSEMENT

POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, N'ENLEVEZ PAS LE COUVERCLE DE CET ENCEINTE. IL N'Y A AUCUNE PIÈCE RÉPARABLE

PAR L'UTILISATEUR. RÉFÉREZ TOUTES LES RÉPARATIONS À UN TECHNICIEN QUALIFIÉ

Pour éviter tout incendie ou choc électrique, n'exposez pas cet équipement à la pluie ou à l'humidité. Ne stockez pas et n'utilisez pas ce

produit à proximité de liquides, sources de chaleur telles que radiateurs, registres de chaleur. Nettoyez uniquement avec un chion sec.

Les utilisateurs doivent faire preuve d'une sécurité supplémentaire lorsque ce symbole apparaît dans ce manuel d'instructions et suivre

toutes les précautions telles qu'elles sont énoncées.

BATTERIE (*Chargement et lecture non pris en charge)

Le MPX-1201 est un haut-parleur de sonorisation alimenté par batterie au lithium. Assurez-vous d'avoir complètement chargé la batterie

avant la première utilisation pour maximiser la durée de vie de la batterie. Une fois que l'adaptateur secteur est connecté à une source

d'alimentation, il commencera automatiquement à se charger (il faut 2-3 heures pour charger complètement la batterie au lithium). Même

si la puissance de la batterie est faible, l'appareil s'allumera lorsqu'il sera connecté à une source d'alimentation. Lorsque la batterie est en

charge, la LED de la batterie est rouge. Lorsque la batterie est complètement chargée, la LED s'éteint. Une fois l'appareil complètement

chargé, veuillez le débrancher de la source d'alimentation. La batterie peut être rechargée environ 300 fois au cours de sa durée de vie.

Lorsqu'il n'est pas utilisé, le haut-parleur doit toujours être réglé sur OFF pour éviter que l'appareil ne décharge la batterie. Si l'appareil

n'est pas utilisé pendant une période prolongée, la batterie perdra progressivement de sa puissance. Il est recommandé de charger

complètement la batterie au moins tous les 60 jours.

CHARGER ET JOUER

Lorsque la batterie est complètement déchargée, l'unité ne peut pas se charger et fonctionner à 100% du volume lorsqu'elle est

immédiatement connectée à une source d'alimentation. Il est suggéré de charger l'appareil pendant un certain temps avant de l'utiliser à

100% du volume. L'unité fonctionnera et se chargera à de faibles niveaux de volume. Le volume de sortie augmentera à mesure que l'unité

continue de se charger.

CONTROL PANEL

1. MASTER VOLUME: Volume control and ON/OFF.

2. Power Supply: DC 5V.

3. GLOBAL CONTROLS:

•Mode: Change between AUX, USB, TF, FM, BT. Press and hold to

activate or deactivate the party lights.

•Previous Track: Select previous track or FM station.

•Play/Pause/TWS: Play/Pauase current track. Press and

hold for TWS.

•Next Track: Select next track or FM station.

4. DISPLAY: LED screen displays the current function.

5. USB Port: Playback MP3 (formatted) Music.

6. TF Card Port: Playback MP3 (formatted) Music.

7. MIC VOL: Mic volume control.

8. MIC ECHO: Echo volume control.

9. AUX IN: Insert a 3.5mm TRS audio cable.

10. MIC IN: Insert a 6.35mm TRS mic cable.

11. CHARGE: Battery charging light. Red=Charging.

PANEL DE CONTROL

1. MASTER VOLUME: control de volumen y encendido / apagado.

2. Fuente de alimentación: DC 5V.

3. CONTROLES GLOBALES:

• Modo: cambia entre AUX, USB, TF, FM, BT. Mantenga presionada

para activar o desactivar las luces de esta.

• Pista anterior: seleccione la pista anterior o la estación de FM.

• Reproducir / Pausa / TWS: Reproducir / Pausar la pista actual.

Presione y mantenga pulsado para TWS.

• Pista siguiente: seleccione la siguiente pista o estación FM.

4. PANTALLA: La pantalla LED muestra la función actual.

5. Puerto USB: reproducción de música MP3 (formateada).

6. Puerto de tarjeta TF: reproducción de música MP3 (formateada).

7. MIC VOL: control de volumen del micrófono.

8. MIC ECHO: Control de volumen de eco.

9. AUX IN: Inserte un cable de audio TRS de 3.5 mm.

10. MIC IN: Inserte un cable de micrófono TRS de 6.35 mm.

11. CHARGE: Luz de carga de la batería. Rojo = Cargando.

PANNEAU DE COMMANDE

1. MASTER VOLUME : Contrôle du volume et ON/OFF.

2. Alimentation: DC 5V.

3. CONTRLES GLOBAUX:

• Mode:changer entre AUX, USB, TF, FM, BT. Maintenez enfoncé pour

activer ou désactiver les lumières de fête.

•Piste précédente : sélectionnez la piste ou la station FM précédente.

•Lecture/Pause/TWS: Lecture/Pause de la piste en cours. Appuyez

sur et tenir pour TWS.

•Piste suivante : sélectionnez la piste ou la station FM suivante.

4. AFFICHAGE : l'écran LED ache la fonction actuelle.

5. Port USB: Lecture de musique MP3 (formatée).

6. Port de carte TF: lecture de musique MP3 (formatée).

7. MIC VOL : contrôle du volume du micro.

8. MIC ECHO : contrôle du volume de l'écho.

9. AUX IN : Insérez un câble audio TRS 3,5 mm.

10. MIC IN : Insérez un câble micro TRS 6,35 mm.

11. CHARGE: voyant de charge de la batterie. Rouge=Chargement.

THE LIGHTNING FLASH

AND ARROWHEAD

WITHIN THE TRIANGLE IS

A WARNING SIGN

ALERTING YOU OF

“DANGEROUS VOLTAGE”

INSIDE THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK,

DO NOT REMOVE THE COVER

(OR BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.



RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

THE EXCLAMATION POINT

WITHIN THE TRIANGLE IS A

WARNING SIGN ALTERTING

YOU OF IMPORTANT

INSTRUCTIONS

ACCOMPANYING THE

PRODUCT.

1. Do not install this equipment in a confined area. Keep in well ventilated openings free of newspapers,

table-cloths, curtains, etc.

2. WARNING: To reduce risk of fire or electric shock, do no expose this unit to rain or liquids.

3. WARNING: The internal or external batteries shall not be exposed to excessive heat such as fire and hot,

direct sunlight. No flame sources, such as lighted candles, should be placed on the apparatus.

4. WARNING: The detachable power cord is for charging. Once fully charged, the unit will operate on internal

rechargeable batteries.

5. Used, depleted batteries can be hazardous and should be discarded in a safe and environmentally sound

manner.

TRUE WIRELESS STEREO

CONEXIÓN TWS

Conexión TWS: La conexión TWS es solo para

dos altavoces de la misma marca y modelo.

1.Habilite el modo Bluetooth (BLUE) en ambos

altavoces.

2. Presione y mantenga presionado el botón

TWS en uno de los altavoces para sincronizar

ambas unidades (deben ser de la misma marca

y modelo para funcionar).

3. En su dispositivo móvil en el menú de

Bluetooth, busque QFX MPX-1201 y conéctese.

4. Abra su aplicación de música favorita y

disfrute de True Wireless Stereo.

5. Para salir de TWS, mantenga presionado el

botón TWS.

TWS CONNECTION

TWS connection: TWS Connection is only for two

speakers of the same make and model.

1.Enable Bluetooth (BLUE) mode on both speakers.

2.Press and hold down the TWS button on one of

the speakers to sync both units together (they must

be the same make and model to function).

3. On your mobile device under the Bluetooth

menu, search for QFX MPX-1201 and connect.

4. Open your favorite music app and enjoy True

Wireless Stereo.

5. To Exit TWS press and hold the TWS button.

CONNEXION TWS

Connexion TWS: La connexion TWS est

uniquement pour deux enceintes de la même

marque et du même modèle.

1.Activez le mode Bluetooth (BLUE) sur les deux

haut-parleurs.

2.Appuyez sur le bouton TWS de l'une des

enceintes et maintenez-le enfoncé pour

synchroniser les deux unités ensemble (elles

doivent être de la même marque et du même

modèle pour fonctionner).

3. Sur votre appareil mobile dans le menu

Bluetooth, recherchez QFX MPX-1201 et

connectez-vous.

4. Ouvrez votre application musicale préférée et

profitez de True Wireless Stereo.

5. Pour quitter TWS, maintenez le bouton TWS

BLUETOOTH:

•Bluetooth mode: use the MODE button to enable Bluetooth on the MPX-1201. Open the Bluetooth settings

on your mobile device and search for QFX MPX-1201. Select the option to pair both devices. Now you can sit

back and enjoy the music from your favorite app. You will not need to reconnect Bluetooth when changing

modes.

•Modo Bluetooth: use el botón MODE para habilitar Bluetooth en el MPX-1201. Abra la configuración de

Bluetooth en su dispositivo móvil y busque QFX MPX-1201. Seleccione la opción para emparejar ambos

dispositivos. Ahora puede sentarse y disfrutar de la música de su aplicación favorita. No necesitará volver a

conectar el Bluetooth al cambiar de modo.

•Mode Bluetooth: utilisez le bouton MODE pour activer Bluetooth sur le MPX-1201. Ouvrez les paramètres

Bluetooth sur votre appareil mobile et recherchez MPX-1201. Sélectionnez l'option pour coupler les deux

appareils. Vous pouvez maintenant vous asseoir et profiter de la musique de votre application préférée. Vous

n'aurez pas besoin de reconnecter Bluetooth lors du changement de mode.

FM RADIO:

• Frequency-Modulated stations operate in a frequency band extending from 87.5 MHz to 108 MHz. Use the

MODE button to select the FM mode. In FM mode, press the Play/Pause button to scan available frequencies

in the area.

• Las estaciones de frecuencia modulada operan en una banda de frecuencia que se extiende desde 87.5

MHz a 108 MHz. Utilice el botón MODE para seleccionar el modo FM. En el modo FM, presione el botón

Reproducir / Pausa para buscar las frecuencias disponibles en el área.

•Les stations à modulation de fréquence fonctionnent dans une bande de fréquences allant de 87.5 MHz à

108 MHz. Utilisez le bouton MODE pour sélectionner le mode FM. En mode FM, maintenez le bouton Lecture /

Pause enfoncé pour balayer les fréquences disponibles dans la zone.

[email protected]

Mon-Fri 9AM - 5PM (PST)

1-800-864-CLUB (2582)

Mon-Fri 9AM - 5PM (PST)

WHERE THE PARTY BEGINSTM

➚

TRUE WIRELESS STEREO

REMOTE CONTROL

1. ESPERA: habilita el modo de espera.

2. MODO: Seleccione entre USB, FM, AUX, BT.

3. MUTE: silencia la pista de audio actual.

4. REPRODUCIR / PAUSAR: reproduce o pausa la

pista de audio.

5. PREV: Selecciona la pista o canal anterior.

6. SIGUIENTE: seleccione la pista o canal

siguiente.

7. EQ: seleccione un modo de EQ.

8. VOL-: Disminuye el volumen.

9. VOL +: aumenta el volumen.

10. Teclas numéricas para seleccionar la pista de la

tarjeta USB y TF.

11. RPT: presione para repetir uno o todos.

12. U / SD: Entrada de señal. Presione para buscar

automáticamente los canales de FM.

1. STANDBY: Enable standby mode.

2. MODE: Select from USB, FM, AUX, BT.

3. MUTE: Mute the current audio track.

4. PLAY/PAUSE: Play or pause the audio track.

5. PREV: Select previous track or channel.

6. NEXT: Select next track or channel.

7. EQ: Select an EQ mode.

8. VOL-: Decrease Volume.

9. VOL+: Increase Volume.

10. Number keys to select track from the USB and TF

Card.

11. RPT: Press to repeat one or all.

12. U/SD: Signal input. Press to auto scan FM channels.

1. VEILLE : Activer le mode veille.

2. MODE : Sélectionnez parmi USB, FM, AUX, BT.

3. MUTE : coupe le son de la piste audio actuelle.

4. LECTURE/PAUSE : Lecture ou pause de la piste

audio.

5. PREV : Sélectionnez la piste ou la chaîne précédente.

6. SUIVANT : Sélectionnez la piste ou la chaîne

suivante.

7. EQ : Sélectionnez un mode EQ.

8. VOL- : diminue le volume.

9. VOL+ : augmentez le volume.

10. Touches numériques pour sélectionner la piste à

partir de la carte USB et TF.

11. RPT : Appuyez pour répéter un ou tous.

12. U/SD : entrée de signal. Appuyez pour rechercher

automatiquement les canaux FM.

DISPLAY SYSTEM SETTINGS

1. Input Mode: The LED display screen will display the information of input mode for USB/TF/BT/ AUX /FM.

When a USB /TF Card is inserted into the USB/TF input, the unit will automatically switch to USB/TF mode and

begin playing MP3 audio files from the USB flash drive / TF Card.

2.Track Number: The track number currently playing from the USB/TF will display.

3. FM Mode: All FM channels display here. Press "play/pause" button for auto scan all channels.

AJUSTES DEL SISTEMA DE PANTALLA

1. Modo de entrada: La pantalla LED mostrará la información del modo de entrada para USB / TF / BT / AUX /

FM. Cuando se inserta una unidad flash USB / tarjeta TF en la entrada USB / TF, la unidad cambiará

automáticamente al modo USB / TF y comenzará a reproducir archivos de audio MP3 desde la unidad flash

USB / tarjeta TF.

2. Número de pista: Se mostrará el número de pista que se está reproduciendo actualmente desde el USB /

TF.

3. Modo FM: aquí se muestran todos los canales FM. Presione el botón "reproducir / pausa" para escanear

automáticamente todos los canales.

PARAMÈTRES DU SYSTÈME D'AFFICHAGE

1. Mode d'entrée: L'écran d'affichage LED affichera les informations du mode d'entrée pour USB / TF / BT /

AUX / FM. Lorsqu'une clé USB / carte TF est insérée dans l'entrée USB / TF, l'appareil bascule automatique-

ment en mode USB / TF et commence à lire des fichiers audio MP3 à partir de la clé USB / carte TF.

2.Numéro de piste: Le numéro de piste en cours de lecture à partir de l'USB / TF s'affiche.

3. Mode FM: Tous les canaux FM s'affichent ici. Appuyez sur le bouton "lecture / pause" pour rechercher

automatiquement toutes les chaînes.

LIMITED PRODUCT WARRANTY POLICY

Before returning your Product for service under this Warranty, please (i) read the instrucon manual carefully and visit our website at www.qfxusa.com for

Product updates and extended support documentaon (e.g., Common Troubleshoong Guides); (ii) if you are sll having trouble with your Product, please

contact the QFX Customer Support Department.

Subject to the terms and condions herein, QFX, Inc. (herein aer called “QFX”) warrants to the original purchaser of the Product

(”Customer”) that for the applicable Warranty Period listed below, the Product will be free from defects in material or workmanship under normal,

non-commercial use (”Defects”).

Warranty Period encompasses, as listed below, separate “Coverage Periods” for Parts and Labor, each Coverage Period to begin from the original date of

Customer purchase. If Customer returns a defecve Product (or any component thereof) during the applicable Warranty Period, QFX will, at its opon, during

the speciﬁed Coverage Periods for Parts and Labor (as applicable either: (i) repair the Product (or, as applicable, any component thereof) or (ii) replace the

Product (or, as applicable, any component thereof) with a new or refurbished Product (or, as applicable, any component thereof), in either case free of

charge to Customer for Parts and/or Labor (as applicable) during the speciﬁed Coverage Period only, and excluding applicable shipping charges (noted

below), for which the Customer is responsible. The foregoing states the Customer’s exclusive remedy and QFX sole liability for breach of the limited warranty

contained herein.

This warranty covers only normal use. This warranty is not transferable. QFX is not responsible for warranty replacement should the QFX label or logo be

removed or should the product fail to be properly maintained or fail to funcon properly as a result of misuse, abuse, immersion in liquids, improper

installaon, improper shipping, damage caused by disasters such as ﬁre, ﬂood, or service other than by QFX. In addion, this warranty excludes any Product

(or, as applicable, any component thereof) that has been subject to or Defects resulng from: (a) any neglect or misuse by a Customer, an accident, improper

applicaon, violaon of operang instrucons for the Product, any other Customer-induced damage, or the alteraon or removal of any Product serial

number; (b) any modiﬁcaon or repair to Product (or, as applicable, any component thereof) by any party other than QFX or a party authorized in wring by

QFX; (c) any damage to Product (or, as applicable, any component thereof) due to power surges, incorrect electrical voltage, misconnecon to any device, or

malfuncon of any device used with the Product (or, as applicable, any component thereof); (d) cosmec damage to the Product (or, as applicable, any

component thereof) caused by normal wear and tear; (e) shipping damage that occurs while the Product is in transit; (f) damage caused by heat sources,

sunlight, electromagnec condions, or other climac condions or (g) any acts of God.

Product is sold to Customer for personal, non-commercial use only. Product is not warranted for Customer’s commercial or rental use. In addion, Product is

not warranted against failure, and should not be used by Customer for any applicaon where (i) there is a risk that any data stored on Product will be

breached or otherwise compromised, or (ii) the date stored on Product is relied upon for medical or lifesaving applicaons. QFX disclaims any Warranty for

any of the foregoing uses to the fullest extent permied by law. Customer assumes any and all risks associated with such uses of Product, and agrees to

indemnify QFX for any damages claimed against QFX for such uses.

EXCEPT FOR EXPRESS WARRANTIES STATED ABOVE AND TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE PRODUCTS ARE PROVIDED “AS IS” AND QFX

DISCLAIMS ALL OTHER WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY (i) OF MERCHANTABILITY, (ii) OF FITNESS FOR A

PARTICULAR PURPOSE, OR (iii) OF NON-INFRINGEMENT OF THIRD PARTY RIGHTS. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO

EVENT WILL QFX BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR PUNITIVE

DAMAGES, INCLUDING, WITHOUT LIMITATION, ANY LOST PROFITS OR REVENUES, LOSS OR INACCURACY OF ANY DATA OR COST OF SUBSTITUTE GOODS,

REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE) AND EVEN IF QFX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, QFX

AGGREGATE LIABILITY TO CUSTOMER FOR ACTUAL DIRECT DAMAGES FOR ANY CAUSE WHATSOEVER SHALL BE LIMITED TO THE CUMULATIVE PRODUCT

FEES PAID BY THAT CUSTOMER FOR THE PRODUCTS CAUSING THE DAMAGES, IF ANY.

This Warranty gives Customer speciﬁc rights, and Customer may also have other rights that vary from jurisdicon to jurisdicon. Warning: Some Products

may contain components that are small enough to be swallowed. Please keep out of reach of children. In order for the return to be processed, you must send

the Product PREPAID to the address below in the original packaging or reasonable substute to prevent damage and include: (1) a dated sales receipt (which

must have a purchase date that falls in the Warranty Period speciﬁed in the table below) that indicates the place of purchase, model number of Product, and

amount paid, (2) a detailed descripon of Customer’s problem with Product, (3) Customer’s full name, phone number, and return address, (3) all of the

accessories that came with the Product package must be sent along with the main Product, (4) a cashier’s check or money order payable to QFX, Inc., in the

amount speciﬁed for the item in the product table below for return shipping and handling. If in the case you cannot provide a money order or cashier’s

check, you can contact The QFX Customer Support Representave to arrange payment via credit card. No returned Product will be shipped back to a PO BOX.

If a returned Product is found to have no problem and/or does not include ALL of the requirements indicated above, it may be returned back to the customer

and will not be processed.

QFX USA®, Inc.

RMA Processing

Customer Support Department

2957 E. 46th Street | Vernon, CA 90058

[email protected]

(800) 864-CLUB (2582) or (323) 864-6900

qfxusa.com

Hours of Operaon: Monday - Friday, 9am - 5pm PST

All prices and details below are for US Desnaons excluding, Hawaii, Alaska and Puerto Rico. For excluded desnaons and NON US desnaons, please

contact The QFX Customer Support Department directly for addional shipping fees and return instrucons.

If you do not ﬁnd your Product below, your Product model conﬂicts with mulple categories, and/or are unsure of which category the Product you have

purchased will fall under, please contact our Customer Support Department for further instrucon.

In order to determine the exact shipping cost that must be included with your prouuct or paid for the product being returned, please refer to the table below.

Please ﬁnd the product you wish to return by category or model number preﬁx. QFX will not provide any return or refund to any customer for merchandise

and will only honor the Limited Warranty restricons menoned in this document.

Please make sure to follow all direcons prior to shipping back your item. If you are not sure what the shipping cost for your item is, or if your item category

conﬂicts in the table below, please feel free to contact the QFX Support Department for further assistance.

THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED OR IMPLIED WARRANTIES INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT

ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESSED OR IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY

PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENT OR REPRESENTATIONS MADE BY ANY OTHER PERSONS OR FIRM ARE VOID. EXCEPT

AS PROVIDED IN THIS WRITTEN WARRANTY, QFX SHALL NOT BE LIABLE FOR ANY LOSS, INCONVENIENCE, OR DAMAGE, INCLUDING DIRECT, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR INABILITY TO USE THE QFX PRODUCT, WHETHER RESULTING FROM BREACH OF

WARRANTY OR ANY OTHER LEGAL THEORY.

Some jurisdicons do not allow limitaons on how long an implied warranty lasts, and some jurisdicons do not allow the exclusion or limitaon of incidental

or consequenal damages, so the above limitaons and exclusions may not apply to you. This warranty gives you special legal rights and you may have other

rights which vary from jurisdicon to jurisdicon.

www.qfxusa.com

Earphones, Headphones, Pocket Radios,

& Small Bluetooth vSpeakers

Personal Stereos

Portable Radio/Cassee

Large Portable Radio Cassee

Mobile Audio

Pro Audio SBX Systems

Pro Audio PBX Systems

Televisions

Telephones