SALTO SYSTEMS S.L. www.saltosystems.com
2/3 226180-ED.2-09/09/2021
Pol. Lanbarren, c/Arkotz nº9, 20180 Oiartzun, Spain.
All contents current at time of publication. SALTO Systems S.L. reserves the right to change availability of any item in this catalog, its design, construction, and/or materials
.
Compliance
NL Hierbij verklaart SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun– Spain) dat het toestel toegangscontroleapparatuur in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 2014/30/EU (EMCD), 2014/35/EU (LVD) en 2011/65/EU
(RoHS). U kunt een kopie van de originele verklaring van overeenstemming vinden op het volgende internetadres:
https://www.saltosystems.com/certificate
PT A SALTO Systems S.L. declara que este equipamento de controlo de acessos está conforme os requisitos essenciais e outras disposições da Diretiva
2014/30/UE (EMCD), 2014/35/UE (LVD) e 2011/65/UE (RoHS). Poderá encontrar uma cópia da declaração de conformidade original na seguinte
direção de internet: https://www.saltosystems.com/certificate
ELECTRICAL WARNINGS
EN
Caution:
‐
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
‐
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
‐
Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
‐
A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Distance between this device and human body must be higher than 20 cm.
FR
Attention:
‐
Risque d'explosion si la pile est remplacée par un type de pile inadéquat. Jetez les piles usagées conformément aux instructions.
‐
La destruction d'une pile par le feu ou dans un four à haute température, le broyage ou encore son découpage mécanique peut entraîner une explosion.
‐
Laisser une pile dans un environnement où la température est extrêmement élevée peut entraîner une explosion, une fuite de liquide ou de gaz inflammable.
‐
Une pile soumise à une pression d'air extrêmement faible peut entraîner une explosion, ou la fuite d'un liquide ou d'un gaz inflammable.
La distance entre cet appareil et le corps humain doit être supérieure à 20 cm.
Recommended batteries
:
Duracell Plus Power (AAA) LR03 MN2400 Duracell Plus Power (AA) LR6 MN1500
Duracell Ultra Power (AAA) LR03 MX2400 Varta Industrial (AA) LR6 04006
Varta Industrial (AAA) LR03 04003 Varta High Energy (AA) LR6 04906
Varta High Energy (AAA) LR03 04903 Varta Max Tech (AA) LR6 MN1500
Varta Max Tech (AAA) LR03 MN2400
Duracell Ultra Power (AAA) LR03 MX1500
MECHANICAL WARNINGS
In order to confirm the correct operation of this electronic device, SALTO recommends using it in combination with a lock destined for that use (door mass,
frequency of use, fire door, etc.) and that is in good operational conditions. Polished finishes are strongly recommended in seaside environments for a
better performance and durability. The environmental conditions mentioned in the data sheets are always referred to non-condensation situations. The
Biocote and IA finishes are painted and sharp objects such as rings or metallic key rings or other metallic objects should be avoided during any cleaning
process. The SALTO product should be treated with care during the installation process to avoid any aggressive contact that may damage the unit. It may
be necessary to loosen the trims mounting during installation. Do not bring the device into contact with oil, paints or acids. Do not paint the door with the
mortise lock or electronic device already mounted on the door. CLEANING THE ELECTRONIC DEVICE: a damp cloth with mild soapy water can be used.
Never use abrasive soaps or sprays. The black chromium finish (“NE” code) is coated with a protective oil that improves the product conservation. Its
presence may increase the appearance of fingerprint traces after the needed product handling. Thus, no cleaning processes are applied at the origin to
avoid removing the protective layer. SALTO recommends cleaning the product surfaces with a damp cloth after its manipulation when the installation is
finished. For best performance, stainless steel should be cleaned regularly. Note that when the door is closed without the lock having been already
programmed, the lock will automatically lock and can only be opened with a Portable Programing Device (PPD). If you have questions or doubts on this,
please contact your authorized SALTO supplier.
LEGAL WARNINGS
The user shall be responsible for the correct use and maintenance of the access control equipment according to the instructions herein. SALTO shall not
be responsible for any defect, malfunction, loss or damage, whether direct or indirect, caused by or arisen from any improper installation or utilization of
the equipment or which contravenes, transgresses or infringes in any manner the above mentioned instructions. SALTO’s liability concerning the
equipment is limited to the warranty provided. The warranty does not cover product failures due to repairs, modifications or product manipulations
performed in the access control equipment or in the inner electromechanical structure by anyone other than authorized SALTO dealers or personnel.
FCC COMPLIANCE STATEMENT (1)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This product is a radio transmitter and receiver to be used in mobile conditions.