Hitachi DVD VCR Combo DVPF73U Manual de usuario
- Categoría
- Reproductores de DVD
- Tipo
- Manual de usuario
Este manual también es adecuado para
English
Español
POWER/STANDBY
CHANNEL
PLAYSTOP/EJECT
VIDEO IN
F. F W DREWREC/IRT
TIMER REC
DVD OUTPUT VCRSTOP PLAY
OPEN/CLOSE
L
(mono)
AUDIO IN R
LINE 2
Recordable
ReWritable
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
DVD/VCR Combo (DVD PLAYER with VIDEO
CASSETTE RECORDER)
INSTRUCTION MANUAL
Instruction manual
To obtain the best performance and ensure years of trouble-
free use, please read this instruction manual completely.
MODEL
DV-PF73U
H9451UD(EN).qx33 03.1.22 7:22 PM Page 1
–
2
–
EN
1L25
WARNING
:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to
possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO
NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the pres-
ence of important operating and maintenance
(servicing) instructions in the literature accom-
panying the appliance.
CAUTION
:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SER-
VICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.
The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 2
–
3
–
EN
1L25
English
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions
should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol clean-
ers. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted ser-
vice and, that for some specific reason, such as the possibil-
ity of the loss of an authorization code for a CATV convert-
er, is not intended to be unplugged by the user for cleaning
or any other purpose, may exclude the reference to unplug-
ging the appliance in the cleaning description otherwise
required in item 5.
6. Attachments - Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
7. Water and Moisture- Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
8. Accessories - Do not place this video
product on an unstable cart, stand, tripod,
bracket, or table. The video product may
fall, causing serious injury to a child or
adult, and serious damage to the appli-
ance. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the video
product. Any mounting of the appliance should follow the
manufacturer's instructions and should use a mounting
accessory recommended by the manufacturer. An appliance
and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the video
product and to protect it from overheating, and these open-
ings must not be blocked or covered. The openings should
never be blocked by placing the video product on a bed,
sofa, rug, or other similar surface. This video product should
not be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the manufac-
turer's instructions have been adhered to.
10. Power Sources - This video product should be operated only
from the type of power source indicated on the marking
label. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power compa-
ny. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
11. Grounding or Polarization - This video product is equipped
with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit, contact your elec-
trician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should be rout-
ed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular atten-
tion to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or cable
system is connected to the video product, be sure the anten-
na or cable system is grounded so as to provide some pro-
tection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA
No. 70, provides information with regard to proper ground-
ing of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the grounding
electrode. (Fig. A)
14. Lightning - For added protection for this video product dur-
ing a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall out-
let and disconnect the antenna or cable system. This will pre-
vent damage to the video product due to lightning and
power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other elec-
tric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the video product.
18. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19. Damage Requiring Service - Unplug this video product from
the wall outlet and refer servicing to qualified service per-
sonnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the video product to its normal operation.
e. If the video product has been dropped or damaged in any
way.
f. When the video product exhibits a distinct change in perfor-
mance this indicates a need for service.
20. Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteris-
tics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
21. Safety Check - Upon completion of any service or repairs to
this video product, ask the service technician to perform
safety checks to determine that the video product is in prop-
er operating condition.
22. Heat - This video product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND
CLAMP
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
H9451UD(EN).qx33 03.1.22 7:22 PM Page 3
–
4
–
EN
1L25
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of all materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local
regulations concerning chemical wastes.
The serial number of this product may be found on the back of the DVD/VCR. This serial number is unique to
your machine. You should record the number and other vital information here and retain this book as a perma-
nent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home
and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings
: Description refers to playback of video cassette tapes.
: Description refers to playback of DVD video discs.
: Description refers to playback of audio CDs.
: Description refers to playback of MP3 discs.
: Description refers to the items to be set in the QUICK mode.
QUICK
MP3
CD
DVD
VCR
SUPPLIED ACCESSORIES
Remote control
DV-RMPF73U(TS18351)
Two AA batteries A/V cables
(approx. 3 feet (100 cm)
long) (TE14751)
+
1
0
3
M
O
D
E
2
S
E
A
R
C
H
9
Z
O
O
M
D
I
S
P
L
A
Y
8
A
U
D
I
O
0
T
O
P
M
E
N
U
S
E
T
U
P
P
L
A
Y
S
K
I
P
C
H
C
H
56
1
A
-
B
R
E
P
E
A
T
R
E
P
E
A
T
7
C
L
E
A
R
/
C
.
R
E
S
E
T
S
U
B
T
I
T
L
E
/
T
I
M
E
R
M
O
D
E
A
N
G
L
E
D
V
D
V
C
R
/
T
V
D
I
S
C
N
A
V
I
G
A
T
I
O
N
V
C
R
S
L
O
W
S
P
E
E
D
R
E
C
R
E
T
U
R
N
M
E
N
U
S
T
O
P
T
V
P
O
W
E
R
V
I
D
E
O
/
T
V
4
S
U
R
R
O
U
N
D
P
A
U
S
E
/
S
T
E
P
V
O
L
T
V
E
N
T
E
R
E
J
E
C
T
O
P
E
N
/
C
L
O
S
E
(5857952)
RF Cable
H9451UD(EN).qx33 03.1.22 7:22 PM Page 4
–
5
–
EN
1L25
English
TABLE OF CONTENTS
■ LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
■ IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . 3
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS USED IN THIS MANUAL. . . . . . . . . . . . . . . . . . 4
■ FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
■ PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
■ ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DISC TYPES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
■ OPERATING CONTROLS AND FUNCTIONS. . . . . . . . . . . 8
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
DISPLAYS DURING OPERATION . . . . . . . . . . . . . . . . . . . 12
LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . 12
■ VCR/DVD SWITCHING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
■ HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DVD/VCR TO TV CONNECTION . . . . . . . . . . . . . . . . . . . . 13
RF OUTPUT CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CONNECTION TO AN AUDIO SYSTEM . . . . . . . . . . . . . . 14
CONNECTION TO A TV (FOR VIDEO) . . . . . . . . . . . . . . . 15
REMOTE CONTROL OF THE TV . . . . . . . . . . . . . . . . . . . . 16
■ SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
AUTOMATIC CHANNEL SET UP. . . . . . . . . . . . . . . . . . . . 17
TO CHANGE THE ON-SCREEN LANGUAGE . . . . . . . . . . 18
CLOCK SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
■ PLAYBACK FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
NORMAL PLAYBACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 19
SEARCH FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
■ RECORDING FUNCTION . . . . . . . . . . . . . . . . . . . . . . . . . 20
NORMAL RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
IRT (Instant Recording Timer). . . . . . . . . . . . . . . . . . . . . . . . 20
TIMER RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
HINTS FOR TIMER RECORDING . . . . . . . . . . . . . . . . . . . 21
■ SPECIAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
COPYING A VIDEO TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 22
MTS (Multi-Channel Television Sound) SYSTEM. . . . . . . . . 22
AUTO REWIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
REAL TIME TAPE COUNTER . . . . . . . . . . . . . . . . . . . . . . 23
■ PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
BASIC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
GENERAL FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DISC NAVIGATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DISC MENU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
INDICE
■ CONTROLES DEL FUNCIONAMIENETO Y SUS FUNCIONES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
■ CAMBIO DE VCR/DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
■ CONEXIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DVD/VCR A CONEXION DE TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
CANAL DE SALIDA RF
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
CONEXION A UN SISTEMA DE AUDIO
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
CONEXION A UN TV (PARA VIDEO)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
■
PREPARACIÓN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
PREPARACION DE CANAL AUTOMATICO
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
PREPARACION DE RELOJ
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
■ REPRODUCCIÓN DE UN DISCO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
REPRODUCCIÓN BÁSICA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
TITLE MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
STEP BY STEP PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . 24
RESUME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
FAST FORWARD / REVERSE SEARCH . . . . . . . . . . . . . . . 24
SLOW FORWARD / SLOW REVERSE . . . . . . . . . . . . . . . . 24
ZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TRACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
TITLE / CHAPTER SEARCH. . . . . . . . . . . . . . . . . . . . . . . . 25
TIME SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
MARKER SETUP SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . 26
REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
MP3 PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
ON-SCREEN INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 28
TRACK SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
RANDOM PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
AUDIO LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
STEREO SOUND MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SUBTITLE LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CAMERA ANGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
CHANGING THE ON-SCREEN DISPLAY . . . . . . . . . . . . . 29
PARENTAL CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
■ DVD SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
AUDIO SETTINGS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
BLACK LEVEL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . 31
VIRTUAL SURROUND . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
DISPLAY SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
LANGUAGE SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
■ TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . 33
■ MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DISC HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
■ SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
H9451UD(EN).qx33 03.1.22 7:22 PM Page 5
–
6
–
EN
1L25
FEATURES
Mode
¡Progressive Scan system
¡Dolby Digital sound
This DVD/VCR can handle Dolby Digital surround sound
with 5.1 channels when connected to a Dolby Digital decoder.
¡Still/fast/slow/step playback
¡Random playback for audio CD and MP3
¡Program playback for audio CD and MP3
¡DVD menus in a desired language
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no input from
the DVD/VCR for five minutes in the stop mode. When the
screen saver program is activated for 30 minutes, the power is
automatically turned off.
¡Subtitles in a desired language
¡Selecting a camera angle
¡Choices for audio language and sound mode
¡Parental lock
¡Automatic detection of discs
This DVD/VCR automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡Playing an MP3 disc
¡Direct Search
¡On-screen display
Information about the current operation can be displayed on
the TV screen, allowing you to confirm the currently active
functions (such as program playback), on the TV screen using
the remote control.
¡Search
Chapter search / Title search / Track search / Time search
¡Repeat
Chapter / Title / Track / Group / All / A-B
¡Zoom
¡Marker
The part designated by user can be called back.
¡
Disc Navigation
Displays the first scenes of each chapter in a title.
DVD
¡Resume Play
¡Virtual Surround
¡Component Video Out Jacks
Jacks located on the back of the DVD/VCR which are used to
send high-quality video to a TV via Component Video In
Jacks.
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Black Level Setting
Mode
Hardware specifications
¡Auto Head Cleaner
¡4 Head HiFi Stereo
¡Trilingual on-screen menu display selectable in
English, French, or Spanish
¡181 channel capability PLL frequency synthesizer
tuner with direct station call
(A cable converter box may be necessary to view scrambled
cable channels.)
Automatic functions
¡Auto power on system
Automatically turns the VCR on when you insert the cassette.
¡Digital Auto Tracking (DTR)
Playback
¡Auto Repeat
¡2 Step Picture Search Operation
¡Index Search
¡Time Search
Recording
¡1 Year, 8 events (including Daily and Weekly Timer
Recording)
¡IRT (Instant Recording Timer)
VCR
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
Selecting Progressive Scan (480p or Interlaced 480i) Playback
¡If your TV is compatible with progressive scanning (480p), connect the TV to the Component Video Output
jacks of the DVD/VCR and set the INTERLACE/PROGRESSIVE SCAN SELECTOR on the back of the
DVD/VCR to P(PROGRESSIVE). Next, set your TV to the progressive scan mode.
If your TV is not compatible with progressive scan, set the INTERLACE/PROGRESSIVE SCAN SELEC-
TOR to I(INTERLACE).
¡Use a commercially available adaptor if the video input jacks of your TVs or monitors are the BNC type.
¡If you switch PROGRESSIVE/INTERLACE when the power is on the DVD/VCR will automatically be
turned off. When you turn on the DVD/VCR again, the last selected scanning system will be employed.
¡
If you select P(PROGRESSIVE) in INTERLACE/PROGRESSIVE SCAN SELECTOR, DVD video signal is not
output from DVD/VCR VIDEO OUT/S-VIDEO OUT jack.
What is Progressive Scanning?
¡Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in
higher resolution than that of traditional (480i) television signals.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 6
–
7
–
EN
1L25
English
ABOUT THE DISCS
The following discs can be played back on this DVD/VCR.
¡
DVD video
¡
DVD-R*
¡
Audio CD
¡
CD-R/RW*
¡
MP3*
* Depending on the types or the writing method of the medium some
discs can not be played.
• Some DVD-R, or CD-R/RW discs made on personal computers, or
on DVD recorders may not be played back properly due to factors
such as scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played back proper-
ly due to different environments or the settings of the application you
use. We recommend always to use the standardized, properly formatted
discs. (Please contact the sales agency for more detail).
This player conforms to the NTSC color system. You cannot play discs
recorded in other color systems such as PAL or SECAM.
¡Some discs include region codes as shown below.
¡The number inside the symbol refers to a region of the world, and
a disc encoded in a specific region format can only be played back
on DVD/VCR with the same region code.
The following discs cannot be played back on this DVD/VCR.
¡
DVD with region codes other than 1 or ALL.
¡
DVD-ROM
¡
DVD-RAM
¡
CD-ROM
¡
VSD
¡
CDV (Only plays back the audio part.)
¡
CD-G (Only plays back the sound.)
¡
CD-I
¡
SACD
¡
Photo CD
¡
Video CD
Any other discs without compatibility indications.
PLAYABLE DISCS
[
DVD
]
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback con-
ditions take priority over user operations on this
DVD/VCR. If a function you selected does not run as
desired, refer to the manual accompanying the disc.
DISC TYPES
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Chapter 4
[
AUDIO CD
]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
[
MP3
]
Data on an MP3 is divided into sections called "groups",
and then into subsections called "tracks", each of which is
given a group or track number.
Example
Group 1 Group 2
Track 1 Track 2 Track 1 Track 2Track 3 Track 4
INSTALLATION LOCATION
For safety and optimum performance of your DVD/VCR:
• Install the DVD/VCR in a horizontal and stable position. Do not
place anything directly on top of the DVD/VCR. Do not place the
DVD/VCR directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of
intense heat. Avoid dusty or humid places. Avoid places with
insufficient ventilation for proper heat dissipation. Do not block the
ventilation holes on the sides of the DVD/VCR. Avoid locations
subject to strong vibration or strong magnetic fields.
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from AC wall
PRECAUTIONS
outlet. Grasp it by the plug.
• If, by accident, water is spilled on your DVD/VCR, unplug the power
cord immediately and take the unit to our Authorized Service
Center for servicing.
• Do not put your fingers or objects into the DVD/VCR cassette hold-
er.
MOISTURE CONDENSATION WARNING
Moisture condensation may occur inside the unit when it is moved
from a cold place to a warm place, or after heating a cold room or
under conditions of high humidity. Do not use the DVD/VCR at least
for 2 hours until its inside is dry.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 7
–
8
–
EN
1L25
–
8 –
–
9
–
EN
1L25
English
28. CLEAR/C.RESET Button
● DVD mode [page 25]
Press to reset the setting.
● VCR mode [page 18]
Press to reset the counter. Press to exit from the MENU
screen.
29. ANGLE Button [page 29]
Press to change the camera angle to see the sequence being
played back from a different angle.
30. SUBTITLE Button [page 29]
Press to select the desired subtitle language.
30. TIMER Button [page 21]
Press to put the VCR into standby mode for a timer record-
ing.
31. MENU Button
● DVD mode [page 24]
Press to display the menu of the Disc.
● VCR mode [page 17]
Press to access the VCR menu.
32. Arrow Buttons
● DVD mode
32.
p / o /
B
/
s
Buttons
Move the cursor and determines its position.
● VCR mode
32.
p / o Buttons
Press to enter digits when setting program (For example:
setting clock or timer program). Press to select the setting
modes from the on screen menu.
B Button
When setting program (For example: setting clock or timer
program), press to determine your selection and proceed to
the next step you want to input. Press to determine the set-
ting modes from the on screen menu. Press to add or delete
channel numbers during channel preset.
s Button
Press to cancel a setting of timer program. Press to correct
digits when setting program (For example: setting clock or
timer program). Press to add or delete channel numbers
during channel preset.
33. ENTER Button
Press to accept a setting.
34. RETURN Button
Returns to the previous operation.
35. VCR/TV Button [page 20]
Use to select VCR or TV position.
This DVD/VCR does not have VCR/TV light. If noise
appears on your TV when you turn on DVD/VCR(VCR
mode), press this button.
●VCR Position
To view playback, to monitor video recordings or to
watch TV using the VCR tuner.
● TV Position
To watch TV or to view one program while recording
another.
36. DVD Button [page 12]
Press to select DVD mode for the remote control.
● You can switch the OUTPUT mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However, if you press
OUTPUT on the front panel first, you need to re-
select the corresponding mode by pressing DVD or
VCR on the remote control.
37. SLOW Button [page 19]
During tape playback, press to view the video tape in slow
motion. Press again to resume normal playback. This but-
ton does not affect DVD playback.
38. SKIP Buttons
● DVD mode
Press to skip Chapters or Tracks.
39. STOP Button
● DVD mode
Press to stop the disc motion.
● VCR mode
Press to stop the tape motion.
40. h Button
● DVD mode
Press to view the DVD picture in fast reverse motion or
to reverse playback of an Audio CD.
● VCR mode
Press to rewind the tape, or to view the picture rapidly in
reverse during the playback mode (Rewind Search).
41. TV POWER Button[Page 16]
To exclusively turn ON/OFF the TV.
42. VIDEO/TV Button
Press to select the external input mode or TV mode of the TV
.
43.
VOL Buttons
Press to exclusively control the TV volume.
44. T
V CH p / o Buttons
Press to exclusively control the TV channels.
45. PAUSE/STEP Button
● DVD mode [page 24]
Press to pause Disc playback. Press repeatedly to
advance the DVD picture step by step (or one frame at a
time).
● VCR mode [page 19]
While recording, press to temporarily stop the recording
(pause). Press a second time to resume normal recording.
You can not pause a Instant Recording Timer. Or, press
during tape playback to freeze the picture. Press to
advance the picture one frame at a time during still mode
.
46. D Button
● DVD mode
Press to fast forward the Disc. Press PAUSE/STEP, then
press this button to begin slow motion playback. Press
this button repeatedly to change the forward speed of
slow motion.
● VCR mode
Press to rapidly advance the tape, or view the picture
rapidly in forward during playback (Forward Search).
47. PLAY Button
● DVD mode
Press to begin playback.
● VCR mode
Press to begin playback.
48. CH Button
● VCR mode
Press to change TV channels on the DVD/VCR.
49. REC Button
Press once to start a recording.
50. SPEED Button [page 20]
Press to select the VCR’s recording speed (SP or SLP)
51. VCR Button [page 12]
Press to select VCR mode for the remote control.
● You can switch the OUTPUT mode either by pressing
OUTPUT on the front panel, or by pressing DVD or
VCR on the remote control. However, if you press
OUTPUT on the front panel first, you need to re-
select the corresponding mode by pressing DVD or
VCR on the remote control.
52. SETUP Button [page 30]
Press to enter the setup mode.
53. DISC NAVIGATION Button [page 23]
Press to display the first scenes of each chapter of the title
being played.
54. TOP MENU Button [page 24]
Press to call up the title menu.
55. DISPLAY Button
● DVD mode [page 29]
Press to access or remove the display screen during
DVD or Audio CD playback.
● VCR mode [page 22]
Press to access or remove the VCR’s on-screen status
display.
56. AUDIO Button [page 28]
Press to select a desired audio language or sound mode.
(
)
H9451UD(EN).qx33 03.1.22 7:22 PM Page 9
–
10
–
EN
1L25
57. Number Buttons
● DVD mode [page 25]
Press to directly select a Track (Audio CD) for playback.
● VCR mode [page 17]
Press to select TV channels on the VCR.
To select channels, enter channel numbers as a two-digit
number for the quickest results. For example, to select
channel 6, press 0 then 6.
58. OPEN/CLOSE Button
Press to open or close the disc loading tray.
54. EJECT Button
Press to eject the video cassette from the VCR.
59. SEARCH MODE Button
● DVD mode [page 25]
Press to access or remove the Search display,
which allows you to go directly to a specific
Title/Chapter/Track/Time.
● VCR mode [page 19]
Press to perform a Time Search or an Index Search.
Caution: Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent damage
to the DVD/VCR.
Notes
¡To use the remote control to operate the DVD/VCR and its features, press DVD on the remote control before pressing other
DVD. Verify that the green DVD OUTPUT Light is on.
¡To use the remote control to operate the VCR and its features, press VCR on the remote control before pressing other
VCR. Verify that the green VCR OUTPUT Light is on.
POWER/STANDBY Button
A-B REPEAT Button
REPEAT Button
MODE Button
SUBTITLE/ TIMER Button
DVD VCRCD
• Turns the DVD/VCR on and
off.
• Turns the player on and off. • Turns the DVD/VCR on and
off.
• Marks a segment
to repeat between A and B.
• Marks a segment
to repeat between A and B.
• Allows you to repeat play
a Chapter or Title.
• Allows you to repeat play
a Track or Disc.
ZOOM Button
• To set black level on/off.
• To set surround on/off.
• Allows you to program
a specific order or
random playback.
• To magnify part
of picture (x2/x4)
ANGLE Button
• Accesses various
camera angles on a disc.
• Accesses various
subtitles on a disc.
AUDIO Button
DISPLAY Button
• Accesses various
audio functions on a disc.
• To select STEREO,
L-CH or R-CH.
• Displays the current disc mode.
SURROUND Button
• Displays the current disc mode. • Displays the current time,
tape counter, channel.
• To activate the 3D sound.
• To search chapter or time.
• To rapidly return to
a location of disc.
• Search the makers.
OPEN/CLOSE/EJECT Button
• To search track or time.
• To rapidly return to
a location of disc.
SEARCH MODE Button
NUMBER Buttons
CLEAR/C.RESET Button
• To open or close the disc tray. • To open or close the disc tray.
• To select chapter directly.
• To select track directly,
use display function,
or input program order.
• Clear the makers.
• Clear the makers.
• Removes status No.
in program input.
Tour of the Remote Control
Buttons on remote control work in different ways for DVD, CD and VCR :
Refer to the following table for correct use.
• Clear the number that is
entered incorrectly.
• Search the makers.
• Clear the number that is
entered incorrectly.
MENU Button
• Brings up the Menu
on a disc.
TOP MENU Button
• Brings up the Top Menu
on a disc.
RETURN Button
• Returns to a previous menu.
• To enter the setting mode for
INDEX SEARCH, TIME
SEARCH.
• To select channel.
• To reset the tape counter.
• Brings up the VCR Menu.
• To exit the VCR Menu.
• Press to put the VCR into
standby mode for a timer
recording.
• Press to eject the video cassette
from the VCR.
MODE
SEARCH
ZOOM
DISPLAY
AUDIO
TOP MENU
A-B REPEAT
REPEAT
SUBTITLE/TIMER
MODE
ANGLE
RETURN
MENU
–
11
–
EN
1L25
English
Tour of the Remote Control
ENTER/Arrow Button
(UP/DOWN or LEFT/RIGHT
Button)
SEARCH Buttons
DVD VCRCD
• Moves the cursor and
determines its position.
SETUP Button
• Brings up the DVD player's
Setup menu.
SKIP Buttons
CH Buttons
• To skip Chapters.
• Allows you to search
forward/backward
through a disc
(×2. ×8. ×30. ×60) .
STOP Button
PLAY Button
• To stop playback.
• Begin disc play.
PAUSE/STEP Button
• Advances playback
one frame at a time.
• Advances playback
one frame at a time.
• To exclusively turn ON/OFF
the TV
• To exclusively turn ON/OFF
the TV
• To exclusively turn ON/OFF
the TV
VIDEO/TV Button
TV POWER Button
VOL Button
CH Button
• Press to select the external input
mode or TV mode of the TV.
• Press to select the external input
mode or TV mode of the TV.
• Press to select the external input
mode or TV mode of the TV.
• Moves the cursor and
determines its position.
• Moves the cursor and
determines its position.
• Brings up the DVD player's
Setup menu.
• To skip Tracks.
• Allows you to search
forward/backward
through a disc (×16) .
• To stop playback.
• Pause disc play.
• Pause disc play.
• Pause tape play or record.
• Press to exclusively control
the TV volume.
• Press to exclusively control
the TV volume.
• Press to exclusively control
the TV volume.
• Press to exclusively control
the TV channels.
• Press to exclusively control
the TV channels.
• Press to exclusively control
the TV channels.
• Begin disc play.
• To stop playback or record.
• To change channels.
• Begin tape play.
DVD Button
• To use the remote contorol
in DVD mode.
VCR/TV Button
• To select the DVD output mode.
• To select VCR or TV position.
• Allows you to forward/backward
through a tape.
SETUP
PLAY
SKIP
CH
CH
DVD
VCR/TV
STOP
TV POWER
VIDEO/TV
PAUSE/STEP
VOL
ENTER
• The first scenes of each chapter
of the title being played will be
displayed.
• To select the VCR output mode.
• To use the remote contorol
in VCR mode.
• To view the tape
in slow motion.
• To select the recoeding speed.
• To start a recording.
VCR Button
SLOW Button
SPEED Button
REC Button
DISC NAVIGATION Button
VCR
SLOW
SPEED
REC
VCR/TV
DISC
NAVIGATION
H9451UD(EN).qx33 03.1.22 7:22 PM Page 11
–
12
–
EN
1L25
DISPLAY DISPLAYS DURING OPERATION
LOADING THE BATTERIES
Stays on when the inserted
disc is being played back.
Lights up when a
CD is inserted into
the tray.
Lights up when a DVD
is inserted into the tray.
Lights up when the
inserted disc comes
to a pause.
Stays on when the
A-B repeat function
is on.
Stays on when the
repeat function is on.
Stays on when repeat
track function is on.
Displays how long a current title
or track has been played back. When
a chapter or track has switched, the
number of the a title, chapter or
track is displayed.
Stays on when
repeat title
function is on.
Stays on when
repeat chapter
function is on.
Stays on when the inserted
cassette is being played back.
Lights up when the playback
is in a still or in a slow mode.
Stays on during playback
when the repeat function
is on.
Works as a tape counter(hour,minute only).
Also displays a channel number,
tape speed remaining time for IRT and
current time.
No disc inserted
/ can not read
Tray open
Tray closed
Loading the Disc
When a disc is being
Play back
1. Open the battery compartment
cover.
2. Insert two AA batteries, with each
one oriented correctly.
3. Close the cover.
Notes
¡Do not mix alkaline and manganese batteries.
¡Do not mix old and new batteries.
DVD
VCR
VCR/DVD SWITCHING
Since this product comprises VCR and DVD players, it is necessary to select the correct output mode.
Press VCR on the remote control.
(Verify that the VCR OUTPUT Light is lit.)
SWITCHING TO VCR MODE
Notes
¡Pressing only OUTPUT on the front panel does not
switch the mode of the remote control. You always
need to select the correct mode on the remote con-
trol too.
Press DVD on the remote control.
(Verify that the DVD OUTPUT Light is lit.)
SWITCHING TO DVD MODE
DVD OUTPUT VCR
+10
EJECT
3
MODE
2
SEARCH OPEN/CLOSE
9
ZOOM
DISPLAY
8
AUDIO
0
TOP MENU
SETUP
PLAY
SKIP
CH
CH
56
1
A-B REPEAT
REPEAT
7
CLEAR/C. RESET
SUBTITLE/TIMER
MODE
ANGLE
DVD VCR/TV
DISC
NAVIGATION
VCR
SLOW SPEED REC
RETURN
MENU
STOP
TV POWER
VIDEO/TV
4
SURROUND
PAUSE/STEP
VOL
TV
ENTER
OUTPUT button
DVD OUTPUT Light
VCR OUTPUT Light
DVD button
VCR button
POWER/STANDBY
CHANNEL
PLAYSTOP/EJECT
VIDEO IN
F.FWDREWREC/OTR
TIMER REC
DVD OUTPUT VCRSTOP PLAY
OPEN/CLOSE
L
(mono)
AUDIO IN R
LINE 2
H9451UD(EN).qx33 03.1.22 7:22 PM Page 12
–
13
–
EN
1L25
English
DVD/VCR TO TV CONNECTION
1. Disconnect the AC power cord of the TV from the
AC outlet.
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of
the DVD/VCR.
4. Connect the DVD/VCR to the TV using the RF cable.
5. Plug the AC power cords of the DVD/VCR and TV
into the AC outlets.
UHF/VHF
[VHF/UHF
combination antenna]
[Back of the DVD/VCR]
IN
OUT
[Cable box or satellite box]
OR
[Indoor antenna]
[Back of the
UHF/VHF combination TV]
RF cable
(supplied)
From Cable or
Satellite Company
OR
DVD/VCR VCR
AUDIO OUT AUDIO IN
VIDEO OUT VIDEO IN
L
ANT-IN
ANT-OUT
R
L
R
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
HOOKUPS
CAUTION:
¡Be sure to turn off the DVD/VCR and equipment to be connected before connecting.
¡Read through the operation manual for the equipment to be connected.
¡Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.
¡Be sure to keep the DVD/VCR connection cables separate from the TV antenna cable when you install the
DVD/VCR, because it may cause electrical interference when you are watching television programs.
If your TV does not have A/V terminals:
1. Connect the DVD/VCR to a TV using RF cable (see
DVD/VCR TO TV CONNECTION).
2. Select channel 3 on your TV.
3. Press PLAY.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback.
¡There is case that the RF output channel does not
change by situation (For example, when you adjust
tracking using CHANNEL .
In this case, stop the playback, and start the play-
back again. After that, press PLAY on the VCR for
3 seconds.
¡If there is a power failure or the DVD/VCR is
unplugged for more than 30 seconds, the RF output
channel setting will return to CH3.
(
)
RF OUTPUT CHANNEL
DVD/VCR VCR
AUDIO OUT AUDIO IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
DVD
Y
C
B
PB
CR
PR
L
R
L
ANT-IN
ANT-OUT
R
L
R
DIGITAL
AUDIO OUT
COAXIAL
I P
PROGRESSIVE
12
11
10
89
7
6
21 3 45
REAR VIEW
1. ANT-IN (Antenna In) Jack
Connect your antenna, Cable Box, or Direct Broadcast
System.
2. DVD/VCR AUDIO OUT Jacks
Connect the supplied audio cables here and to the Audio
In jacks of a television or other audio equipment.
3. AUDIO IN Jacks (VCR only)
Connect audio cables coming from the audio out jacks
of a camcorder, another VCR, or an audio source here.
4. AC Power Cord
Connect to a standard AC outlet to supply power to the
DVD/VCR.
5. COMPONENT VIDEO OUT Jacks (DVD only)
Connect optional component video cables here and to
the component Video In jacks of a television.
6. COAXIAL Jack (DVD only)
Connect an optional coaxial digital audio cable here and
to the Coaxial Digital Audio In jack of a decoder or
audio receiver.
7. DVD AUDIO OUT Jacks (DVD only)
Connect the supplied audio cables here and to the Audio
In jacks of a television or other audio equipment (DVD
only).
8. S-VIDEO OUT Jack (DVD only)
Connect an optional S-Video cable here and to the S-
Video In jack of a television.
9. INTERLACE/PROGRESSIVE SCAN SELECTOR
T
o select interlace or progressive scanning.
(See page 6)
10. VIDEO IN Jack (VCR only)
Connect a cable coming from the video out jack of a
camcorder, another VCR, or an audio-visual source
(laser disc player, video disc player, etc.) here.
11. DVD/VCR VIDEO OUT Jack
Connect the yellow video cable (supplied) here and to
the TV’s Video In jack.
If you select P(PROGRESSIVE) in
INTERLACE/PROGRESSIVE SCAN SELECTOR,
DVD video signal is not output to your TV.
12. ANT-OUT (Antenna Out) Jack
Use the supplied RF coaxial cable to connect this jack
to the ANTENNA IN Jack on your TV.
Notes
¡The S-VIDEO OUT jack, COAXIAL jack and COM-
PONENT VIDEO OUT jack are only useful in DVD
mode.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 13
–
14
–
EN
1L25
CONNECTION TO AN AUDIO SYSTEM
RL
DVD/VCR VCR
VIDEO OUT
AUDIO OUT AUDIO IN
L
R
VIDEO IN
L
R
DVD
S-VIDEO OUT COMPONENT
VIDEO OUT
AUDIO
OUT
DIGITAL
AUDIO OUT
L
R
COAXIAL
Y
C
B
/
P
B
C
R
/
P
R
Stereo system
Dolby Digital decoder
or
DTS decoder
Notes
¡If output Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to BITSTREAM for
audio output in the setup mode. (See page 30)
¡Unless connected to a Dolby Digital decoder, set Dolby Digital to PCM for audio output in the setup mode.
Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers. (See
page 30)
¡The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound
by an MD or DAT deck.
¡
Set Dolby Digital to PCM for audio output in the setup mode for method 1 only. Playing a DVD using incorrect set-
tings may generate noise distortion, and may also damage the speakers. (Refer to page 30 to set BITSTREAM for
Dolby Digital)
COAXIAL
DVD
S-VIDEO OUT COMPONENT
VIDEO OUT
AUDIO
OUT
DIGITAL
AUDIO OUT
L
R
COAXIAL
Y
C
B
/
P
B
C
R
/
P
R
AUDIO
DVD/VCR
Method 1
Audio Input Jacks
Digital Audio
Input Jacks
Analog Audio Out
Digital Audio Out
Method 2
• Method 1 DVD/VCR + Stereo system
• Method 2 DVD/VCR + Dolby Digital decoder or DTS decoder
H9451UD(EN).qx33 03.1.22 7:22 PM Page 14
–
15
–
EN
1L25
English
CONNECTION TO A TV (FOR VIDEO)
CBYCR
RL S-VIDEO IN
COMPONENT
VIDEO IN
VIDEO IN
or or
or
PBYPR
DVD/VCR VCR
VIDEO OUT
AUDIO OUT AUDIO IN
L
R
VIDEO IN
L
R
DVD/VCR VCR
VIDEO OUT
AUDIO OUT AUDIO IN
L
R
VIDEO IN
L
R
DVD
S-VIDEO OUT COMPONENT
VIDEO OUT
AUDIO
OUT
DIGITAL
AUDIO OUT
L
R
COAXIAL
Y
C
B/
PB
CR/
PR
DVD
S-VIDEO OUT COMPONENT
VIDEO OUT
AUDIO
OUT
DIGITAL
AUDIO OUT
Y
C
B/
PB
CR/
PR
L
R
COAXIAL
Y
C
B/
PB
CR/
PR
DVD
S-VIDEO OUT COMPONENT
VIDEO OUT
AUDIO
OUT
DIGITAL
AUDIO OUT
L
R
COAXIAL
Analog Audio out
Video out
• Method 1 DVD/VCR + TV with Video Input Jack
• Method 2 DVD/VCR + TV with S-Video Input Jack
• Method 3 DVD/VCR + TV with Component Video Jacks
TV
Method 1
Good pictureBasic Audio
Method 2 Method 3
Better picture Best picture
S-Video out
Component Video out
AV Cable
S-Video
Cable
Video
Cables
Notes
¡Connect the DVD/VCR directly to a TV. If the A/V cables are connected to a VCR, pictures may be
distorted due to the copy protection system.
¡If your TV is compatible with progressive scanning (480p), connect the TV to the component video output
jacks of the DVD/VCR.
¡When P (PROGRESSIVE) is selected at the INTERLACE/PROGRESSIVE SCAN SELECTOR, no video
signal will be output from the VIDEO OUT or S-VIDEO OUT Jack.
DVD/VCR
H9451UD(EN).qx33 03.1.22 7:22 PM Page 15
–
16
–
EN
1L25
–
16
–
EN
2C05
CONTROLLING THE TV
Once programmed, the DVD/VCR’s remote control is
ready to control the TV.
NOTE: Be aware that not all of your TV’s functions
may work even though the remote control is
correctly programmed.
To operate the TV
¡You can turn on your TV by pressing the TV
POWER button.
¡You can change the channels with the TV CH
(o/p) and the volumes with VOL (o/p) .
To operate the DVD/VCR
Press the VIDEO/TV to operate your DVD/VCR with
the remote.
NOTE: VIDEO/TV button is not corresponded to
TV which can switch to TV input mode
directly.
PROGRAMMING THE REMOTE
CONTROL FOR THE TV
1
Turn off the TV.
2 Program the remote control
Aim the DVD/VCR’s remote control at your TV set.
Hold down the TV POWER button while you press
the number corresponding to your brand of television
as shown in the chart.
For example; If you have a Hitachi television, press
the TV POWER and 1 at the same time. If this but-
ton combination sends a signal that matches with
your TV, the TV will turn on, and you’ll know the
remote is set to control the television.
NOTES:
¡If that button combination does not change the TV
channel, go through the whole list of button combi-
nations one by one until you find one that does
change your TV channel.
¡Also, if your brand of TV is not listed in the chart,
try all the number buttons. One of them may work
for you.
¡If the TV channel still doesn’t change after going
through all the button combinations listed, it is like-
ly that you will not be able to program this remote
control for your TV.
REMOTE CONTROL OF THE TV
TV Brands Press the TV and This Number
HITACHI 1
SONY 2
RCA 3
SANYO 4
ZENITH 5
PANASONIC1 6
PANASONIC2 7
SHARP1 8
SHARP2 9
TOSHIBA 0
JVC CLEAR
MITUBISHI +10
MAGNAVOX SUBTITLE
FUNAI AUDIO
GOLDSTAR DISPLAY
H9451UD(EN).qx33 03.1.22 7:22 PM Page 16
–
17
–
EN
1L25
English
6 After scanning, the tuner stops on the low-
est memorized channel. The TV screen
returns to TV mode.
¡If “AUTO SET UP” appears on the TV screen again,
check the cable connections. Press B once again and
the VCR will begin preset again.
AUTOMATIC CHANNEL SET UP
SETUP
You can automatically program the tuner to scan only
the channels you receive in your area.
¡Channel memory programming is NOT needed
when you connect the VCR to a cable box or a satel-
lite box as in "DVD/VCR TO TV CONNECTION"
on page 13. In this case, select channel 3 on your TV.
Then, the channel you want to record or view may
be selected at the cable box or satellite box.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV.
¡Follow the steps below once. Repeat only if there is
a power failure or if the VCR is unplugged for more
than 30 seconds. (In these cases, the programmed
channels are erased.)
¡You must follow the steps below before attempting
to play or record a video tape. If you want to play
or record a video tape BEFORE programming the
tuner, you can cancel it by pressing
CLEAR/C.RESET.
1 You need to connect the antenna or cable to
the VCR first. Then, connect the DVD /VCR
power plug to a standard AC outlet.
2 Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV. (See “RF Output Channel”
on page 13 for the detail.)
3 Turn on the VCR by pressing y/I. the
POWER light will come on.
4 Select the On Screen Language (“ENG-
LISH”, “FRANCAIS” or
“ESPAÑOL”) by pressing
K
or L. Then, press B.
5 Begin channel preset by pressing B once.
The tuner scans and memo-
rizes all active channels in
your area.
¡The VCR distinguishes between
standard TV channels and cable
channels.
VCR
TO SELECT A DESIRED CHANNEL
You can select the desired channel by using CHAN-
NEL (o/p) or by directly pressing Number on the
remote control.
Note for using the Number:
¡When selecting cable channels which are higher
than 99, enter channel numbers as a three-digit num-
ber.(For example: 117, press 1,1,7)
¡You must precede single-digit channel numbers with
a zero (For example: 02, 03, 04 and so on).
TO PRESET THE CHANNELS AGAIN
1 Press MENU until the main menu appears.
(If you have already set the clock, you only
have to press it once. If not, you have to
press it twice).
2 Select “CHANNEL SET UP” by pressing K
or L. Then, press B.
3 Select “AUTO SET UP” by pressing K or L.
Then, press
B.
¡After scanning, the tuner stops on the lowest memo-
rized channel.
AUTO SET UP
CH 01
H9451UD(EN).qx33 03.1.22 7:22 PM Page 17
–
18
–
EN
1L25
CLOCK SET UP
1 Select main menu by pressing MENU.
¡If the clock is not set, the CLOCK SET menu
appears first. In this case, follow step [3].
2 Select "CLOCK SET" by pressing K or L.
Then, press
B.
3 Set the clock.
¡To go back one step, press s.
4 Start the clock by pressing
CLEAR/C.RESET or
B.
VCR
CLOCK SET
MONTH DAY YEAR
03 / 17 MON 2003
HOUR MINUTE AM/PM
05 : 40 PM AM
PM
1) Set the month
Press K or L repeatedly.
Then, press B.
2) Set the day
Press K or L repeatedly.
Then, press B.
3) Set the year
Press K or L repeatedly.
Then, press B.
The day of the week will appear automatically.
4) Set the hour
Press K or L repeatedly.
Then, press B.
5) Set the minute
Press K or L repeatedly.
Then, press B.
6) Set AM or PM
Press K or L repeatedly.
TO CHANGE THE ON-SCREEN
LANGUAGE
1 Press MENU twice to call up the main
menu. (If you have already set the clock,
you only have to press it once).
2 Select "LANGUAGE SELECT" by pressing K
or L. Then, press B.
3 Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL" by pressing
K or L. Then, press
CLEAR/C.RESET.
¡If you accidentally select Spanish or French and
need English: Press MENU and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press
B,
and select ENGLISH by pressing
K or L. Finally,
press CLEAR/C.RESET.
VCR
TO ADD/DELETE CHANNELS
When scanning, some channels may be skipped due to
a weak signal. In such cases, you can add the channels
to the VCR memory manually.
1 Press MENU until the main menu
appears.(If you have already
set the clock, you only have
to press it once. If not you
have to press it twice).
2 Select "CHANNEL SET UP" by pressing K
or L. Then, press B.
3 Select "MANUAL SET UP" by pressing K or
L. Then, press B.
4 Enter the desired channel number by press-
ing
K or L.
5 Add or Delete it from memory by pressing
B or s so that "ADD" or "DELETE" flashes
on the TV screen accordingly.
6 Exit the Preset mode by pressing
CLEAR/C.RESET.
- MENU -
TIMER PROGRAMMING
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
SAP
[OFF]
[ON]
H9451UD(EN).qx33 03.1.22 7:22 PM Page 18
–
19
–
EN
1L25
English
PICTURE SEARCH
If you want to skip or repeat a scene during playback,
press D or E.
¡Press it again and the VCR will now search at super
high speed. (in the LP/SLP modes only).
INDEX SEARCH
An index mark will be assigned at the beginning of
each recordings you make. You may skip to a specific
marked point by following the steps below.
1 Press SEARCH MODE so that the Index
Search menu appears.
2 Enter the number of recordings you wish to
skip by pressing
K or L
within 30 seconds.
3 Press B or { to start index search.
¡If you want to go in the forward direction, press B.
If you want to go in the reverse direction, press {.
¡If you want to stop search function, press STOP.
¡After index search, the VCR will play the tape auto-
matically.
TIME SEARCH
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
1 Press SEARCH-MODE so that the Time
Search menu appears.
2 Enter your desired time to
skip by pressing
K or L
within 30 seconds.
3 Press B or { to start time search.
¡If you want to go in the forward direction, press B.
¡If you want to go in the reverse direction, press {.
¡If you want to stop search function, press STOP.
¡After time search, the VCR will play the tape auto-
matically.
VCR
PLAYBACK FUNCTION
NORMAL PLAYBACK
1 Insert a prerecorded tape. The DVD/VCR will
turn on.
¡If the safety tab has been removed, the
VCR will start playback automatically.
¡If a cassette is in DVD/VCR, STOP sym-
bol appears in TV screen when turning on the
DVD/VCR(VCR mode).
2 Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV. (See “RF Output Channel”
on page 13 for the detail.)
¡If you connect a TV to the DVD/VCR in AV cable,
set the TV to channel AUX.
3 Begin playback by pressing PLAY.
¡Tracking adjustment will be done automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press SKIP/CH on
the remote or CHANNEL (o/p) on the VCR.
¡When a tape has reached the end, the VCR will
rewind the tape to the beginning and eject the tape
automatically.
4 To stop playback, press STOP.
¡If no corresponding symbols appear on the display
when you press buttons such as PLAY, RECORD,
D or E, that means no cassette tape is in the
VCR. Please insert a tape.
VCR
STILL/SLOW
You can freeze the picture on TV screen by pressing
PAUSE/STEP during playback.
¡You can advance the picture one frame at a time by
pressing PAUSE/STEP during the Still mode.
¡You cannot manually adjust the tracking of a still
picture. However, if the picture begins to vibrate ver-
tically during the still mode, you can stabilize the
picture by pressing CHANNEL (o/p).
¡If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV, if so equipped.
¡You can watch in the slow motion by pressing
SLOW during playback or the still mode.
¡If a noise bar appears on the TV screen, you can
reduce it by pressing CHANNEL (o/p).
¡After the VCR has been in Still/Slow mode for 5
minutes, it will stop automatically to protect the tape
and the video head from damage.
¡To return to playback, press PLAY.
AUTO REPEAT PLAYBACK
This feature allows you to play a tape over and over.
VCR
SEARCH FUNCTIONS
1 Select main menu by pressing MENU.
2 Select "AUTO REPEAT" by pressing K or L.
3 Begin auto repeat playback by pressing B
so that ON appears next to "AUTO
REPEAT".
¡If the on-screen menu still remains,
press CLEAR/C.RESET to exit the menu.
¡To cancel the Auto repeat mode, press B at step [3]
so that OFF appears next to "AUTO REPEAT".
TIME SEARCH
2 : 50
INDEX SEARCH
03
Counter Reset
¡You can reset the counter by pressing
CLEAR/C.RESET on the remote control.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 19
–
20
–
EN
1L25
RECORDING FUNCTION
It may be UNLAWFUL to record copyrighted materi-
al without the consent of the copyright owner.
Accidental Erasure Prevention
To prevent accidental recording on a
recorded cassette, remove its record safe-
ty tab. To record on it later, cover the
hole with cellophane tape.
Before recording, make sure:
¡The desired channel is selected by pressing Number
on the remote control or CHANNEL (o/p). (If you
connected the VCR to a cable box or satellite box as
in "DVD/VCR TO TV CONNECTION" on page 13,
select channel 3 on your TV. Then, select the chan-
nel you want to record with the cable box or satellite
box. In this case, you can ONLY record and view the
SAME channel.)
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same chan-
nel (CH4) on your TV.
¡There is a tape with a safety tab in the VCR.
¡The desired recording speed is selected in SP (stan-
dard play) or SLP (super long play) mode by press-
ing SPEED on the remote control.
¡TV STEREO or SAP is selected.
VCR
Type of tape T60 T120 T160
SP mode 1 hour 2 hours 2-2/3 hours
SLP mode 3 hours 6 hours 8 hours
Tape Speed Recording/Playback Time
1 Begin the recording by pressing RECORD.
The REC Light comes on.
¡To temporarily stop recording or to resume it, press
PAUSE/STEP. After the VCR has been in Pause
mode for 5 minutes, it will stop automatically to pro-
tect the tape and the video head from damage.
2 Press STOP when the recording is completed.
Note
¡When you wish to watch another program while
recording, select desired channel on your TV. If
noise appears press VCR/TV.
VCR
IRT (Instant Recording Timer)
This feature allows you to set the recording length sim-
ply by pressing REC/IRT on the VCR.
3 Press REC/IRT to begin IRT. The REC,
TIMER Light comes on. Change the record-
ing length by pressing REC/IRT repeatedly.
VCR
¡If a tape ends during IRT, the VCR will stop, eject
the tape, and switch to the DVD mode automatical-
ly as the TIMER light blinks. (If the DVD power is
off, the VCR will become STANDBY status).
¡When IRT is finished , the VCR turns off automati-
cally. To use the VCR again, press TIMER on the
remote, or STOP/EJECT on the DVD/VCR.
TIMER RECORDING
You may set the VCR to start recording while you are
away. You can set eight programs to record on specific
days, daily or weekly within 1 year period.
If you have not yet set the clock, "CLOCK SET"
appears. If so, follow the steps [3] and [4] in "CLOCK
SET" section on page 18. Then, set the timer record-
ing.
1 Insert a tape with its safety tab into the
DVD/VCR.
2 Select main menu by pressing MENU.
3 Select "TIMER PROGRAMMING" by press-
ing
K or L. Then, press B.
The set up screen is dis-
played.
4 Set the timer.
¡To go back one step, press s.
VCR
PROGRAM NUMBER 4
ONCE
DAILY
WEEKLY
PROGRAM NUMBER 4
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
PROGRAM NUMBER 4
DATE - - / - -
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
ONE TIME PROGRAM
1) Set the program number (1-8)
Program number which is not set up
flashes. Press K or L repeatedly
for the desired program number.
Then, press B.
2) Set the frequency of the recording
For once: Press K or L to point to
"ONCE".
For daily (Monday~Friday): Press K
or L to point to "DAILY".
For weekly: Press K or L to point
to "WEEKLY".
Then, press B.
3) Set the date
First, press K or L for the month.
Then, press B. Next, press K or
L for the day. Then, press B.
Record safety tab
PROG 12345678
DATE -
START TIME
END TIME
CHANNEL
REC SPEED
TIMER PROGRAMMING
REC IRT(0:30) IRT(1:00).....
(Normal recording)
IRT(8:00) IRT(7:30)
NORMAL RECORDING
H9451UD(EN).qx33 03.1.22 7:22 PM Page 20
–
21
–
EN
1L25
English
HINTS FOR TIMER
RECORDING
¡If there is a power failure or the DVD/VCR is
unplugged for more than 30 seconds, the clock set-
ting and all timer settings will be lost.
¡If a tape ends during TIMER RECORDING, the
DVD/VCR will stop, eject the tape, and switch to the
DVD mode automatically as the TIMER light
blinks. (If the DVD power is off, the VCR will
become STANDBY status).
¡
If a tape is not in the
DVD/VCR
or does not have a
safety tab, the TIMER light flashes and timer recording
will not operate. Please insert a recordable
tape.
VCR
¡
When all timer recordings are finished, the TIMER
light will flash. To use the
DVD/VCR
again as usual,
press TIMER to disable the flashing TIMER light,
then press VCR/TV to select the VCR position. Select
either VCR or DVD mode, then continue with the
other features as described in this manual.
¡
When timer recordings are set, the TIMER light will
come on. To use the
DVD/VCR
as usual until the time
for the recording, press TIMER so that TIMER light
disappears. Press VCR/TV to choose the VCR posi-
tion. Select either VCR or DVD mode, then continue
with the other features as described in this manual.
If you want to use the DVD player during
a VCR timer recording or while the
TIMER light is on or flashes.
¡
You can use the DVD player while the TIMER light is
on or flashes, or during a timer recording. Press y/I to
turn on the DVD player. ;Press DVD on the remote
control to choose DVD mode, then continue with the
other DVD features as described in this manual. You
don’t have to set the TIMER off to use the DVD only.
PROGRAM NUMBER 4
DATE 05 /12 MON
START TIME - - : - - - -
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME - - : - - - -
CHANNEL - -
REC SPEED - -
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL - -
REC SPEED - -
ONE TIME PROGRAM
Press K or L repeatedly for the
desired channel number. Then,
press B.
PROGRAM NUMBER 4
DATE 05 /12 MON
START TIME 07: 30 PM
END TIME 08: 30 PM
CHANNEL
16
REC SPEED SP
SP
SLP
ONE TIME PROGRAM
4) Set the start time
First, press K or L for the hour.
Then, press B. Next, press K or L
for the minute. Then, press B. And
then, press K or L for AM or PM. Then, press B.
5) Set the end time
Follow the instructions of
"Set the start time" to set
the end time.
7) Set the tape speed
Press K or L repeatedly for the
desired tape speed. Then, press B.
6) Set the channel number
If you connected the DVD/VCR to a cable box or satellite box
as in "DVD/VCR TO TV CONNECTION" on page 14, select
the DVD/VCR to channel 3 or 4 the same channel as RF
output channel of the DVD/VCR. Then, select the channel you
want to record with the cable box or satellite box.
Leave the cable box or satellite box on for timer recording.
5 To set another program, repeat step [4]. To
exit, press CLEAR/C.RESET.
6 Press TIMER to set the timer.
¡The TIMER light on the VCR comes on. TIMER
RECORDING WILL NOT BE ACTIVATED
UNLESS YOU PRESS TIMER.
TO STOP AN AUTOMATIC TIMER PRO-
GRAM ALREADY STARTED
Press STOP/EJECT on the DVD /VCR.
TO CHECK, CORRECT, OR CANCEL AN
AUTOMATIC TIMER PROGRAM
1 Press TIMER.
¡If the VCR’s power is off, press y/I instead of
TIMER, then go on to the next step.
¡If the DVD output mode is selected, you have to
switch it to the VCR mode by pressing the VCR on
the remote control or the OUTPUT on the VCR.
2 Select main menu by pressing MENU.
3 Select "TIMER PROGRAMMING" by press-
ing
K or L. Then, press B.
4 Select the program number you want to
check by pressing
K or L.
¡The details of the selected program appears on the
TV screen.
¡Go to the digit you want to change by pressing B or
s. Then, enter correct numbers by pressing o or p.
¡You may cancel the entire program by pressing s
while the program number flashes.
5 Press CLEAR/C.RESET to exit.
6 Press TIMER to return to timer stand-by
mode.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 21
–
22
–
EN
1L25
COPYING A VIDEO TAPE
SPECIAL FEATURES
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning:
Unauthorized recordings of copyrighted video tapes
may be an infringement of copyright laws.
Connect the recording DVD/VCR (this unit), the play-
ing VCR (another source) and your TV using the fol-
lowing diagram.
¡You can use the AUDIO/VIDEO input jacks on the
front panel of the DVD/VCR instead of using the
jacks on the back.
VCR
[Playing VCR]
(another source)
S-VIDEO
OUT
CONPONENT
VIDEO OUT
AUDIO
OUT
DVD
Y
L
R
DIGITAL
AUDIO OUT
COAXIAL
DVD/VCR VCR
AUDIO OUT AUDIO IN
VIDEO OUT VIDEO IN
L
ANT-IN
ANT-OUT
R
L
R
CB
PB
CR
PR
I P
PROGRESSIVE
IN
LEFT
RIGHT
OUT
AUDIO
VIDEO
ANT in
[TV set]
(Use for monitoring)
Coaxial cable
(supplied)
Audio/Video cables
(not supplied)
[Recording DVD/VCR]
(this unit)
MTS (Multi-Channel Television
Sound) SYSTEM
When you play a VHS tape, or receive a broadcast on
the VCR tuner channel you are
watching, the current status will
appear when you press DIS-
PLAY on the remote control.
When you record a MTS broad-
cast signal, you need to set it to
MTS mode.
1)* Press MENU and select "TV STEREO" or
"SAP" by pressing
K or L. Then, press B
for fix mode. To exit, press
CLEAR/C.RESET.
¡Although a program may be broadcast in both stereo
and sub audio, you must select the Recording mode
to TV STEREO or SAP before you record a broad-
cast.
2)* Press MENU and select "AUDIO OUT" by
pressing
K or L. Then, press B. Next,
select "HIFI" or "MONO" by pressing
K or
L. To exit, press CLEAR/C.RESET.
¡While the VCR is set in HIFI stereo mode, HIFI
appears on the TV screen. While the VCR is set in
monaural (MONO) mode, HIFI disappears from the
TV screen.
VCR
MTS RECORDING/MONITOR MODE
Type of
broadcast
Hi-Fi audio track
(2-channel)
Normal audio
track
Regular
(
monaural
audio)
-None-
Mono
Stereo
broadcast
STEREO L+R
Bilingual
broadcast
SAP
Main audio
program
Sub audio
program
Stereo &
Bilingual
broadcast
STEREO
SAP
L+R
I
STEREO/SAP
Selection
-Invalid-
- nvalid-
TV STEREO*
SAP*
TV STEREO*
SAP*
L-channel
Mono
L
Main audio
program
Sub audio
program
L
Sub audio
program
R-channel
Mono
R
Main audio
program
Sub audio
program
R
Sub audio
program
Sub audio
program
*
Display on the
TV screen
STOP 12:00AM
CH 32
STEREO
SAP
SP 0:00:00 HIFI
1)*
2)*
1 Insert a pre-recorded tape into the playing
VCR.
2 Insert a tape with a safety tab into the
recording VCR.
3 Press SPEED on the recording VCR to
select the desired recording speed
(SP/SLP).
4 Select the “L1” or “L2”position on the
recording DVD/VCR by pressing the CHAN-
NEL (
K/L ).
¡
When you use the A/V input jacks on the back of the
DVD/VCR, select "L1" position by pressing [0], [0],
[1] on the remote control or the CHANNEL(o/p) Buttons.
¡
When you use the A/V input jacks on the front of the
DVD/VCR, select "L2" position by pressing [0], [0],
[2] on the remote control or the CHANNEL(o/p) Buttons.
Note
“L1” and “L2” are found before the lowest memo-
rized channel. (Example: CH2)
5 Press REC/IRT on the recording VCR.
6 Begin playback of the tape in the playing
VCR.
¡For best results during dubbing, use the DVD/VCR’s
front panel controls whenever possible. The remote
control might affect the playing VCR’s operation.
TO MONITOR THE RECORDING
1 Turn on the TV and set the TV to channel 3.
¡If noise appears, change the RF output channel of
the VCR to channel 4 by pressing PLAY for 3 sec-
onds during playback. Then select the same channel
(CH4) on your TV. (See “RF Output Channel” on
page 13 for the detail).
2 Press VCR/TV on the remote control of the
recording DVD/VCR.
¡Always use video-quality shielded cables with
RCA-type connectors. Standard audio cables are not
recommended.
¡You can use a video disc player, satellite receiver,
camcorder or other audio/video component with
A/V outputs in place of the playing VCR.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 22
–
23
–
EN
1L25
English
BASIC PLAYBACK
Getting started
¡Turn on the power of the TV, amplifier and any other
components which are connected to the DVD/VCR.
¡Make sure the TV and audio receiver (commercially
available) are set to the correct channel.
¡Select DVD mode by pressing DVD on the remote
control or output on the front panel.
1 Press y/I.
¡“Load” will appear briefly on the display panel.
¡Check that the DVD OUTPUT Light is lit. If not,
press the DVD button on the Remote control to
switch to DVD mode.
2 Press OPEN/CLOSE to open disc loading
tray.
3 Place the chosen disc in the tray, with the
label facing up.
CD
DVD
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a mal-
function.
¡If a disc is dirty or has scratches, the pictures may
appear distorted and the playback operation may
stop. In such cases, clean the disc and unplug the
power cord and then plug it again before resuming
playback.
PLAYING A DISC
AUTO REWIND
When a tape reaches the end during recording, play-
back, or fast-forward, the tape will automatically
rewind to the beginning. After rewinding finishes, the
DVD/VCR will eject the tape and switch itself off.
¡The DVD/VCR will not rewind the tape automati-
cally during timer recording or Instant Recording
Timer.
REAL TIME TAPE COUNTER
¡This shows the elapsed recording or playback time
in hours, minutes, and seconds. (The displayed time
will not change during blank portions of the tape.
The front display of DVD/VCR will show in hour,
minute only.)
¡The indication will appear when the tape is rewound
further than “0:00:00” on the tape counter.
4 Press PLAY.
¡The tray will close automatically, and playback will
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
PLAY.
¡When you playback the DVD which a title menu is
recorded, it may appear on the screen. In this case,
refer to “TITLE MENU” on page 24.
5 Press STOP to stop playback.
Notes
¡A “prohibited icon” may appear at the top-right
on the TV screen during operation, warning that a
prohibited operation has been encountered by the
DVD/VCR or the disc.
¡With DVDs that use titles for playback program sig-
nals, playback may start from the second title, or it
may skip these titles.
GENERAL FEATURES
DVD may contain menus to navigate the disc and
access special features. Press appropriate numerical
button or use Arrow (L/K/B/s) to highlight your
selection in the DVD main menu and press ENTER to
confirm.
Note
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
DISC NAVIGATION
1 Press DISC NAVIGATION.
DURING TITLE PLAYBACK OR WHEN RESUME IS ON:
¡The first scene of each chapter of the title being
played will be displayed.
IN STOP MODE (RESUME OFF):
¡The first scene of each chapter of the first title will
be displayed.
2 Press Arrow (K/L/s/B) to select your
desired chapter.
¡Up to 6 chapters can be displayed at one time. If
the title has more than 6 chapters, press SKIP G
to go to the next page. Press SKIP H to go back
to the previous page.
¡You can change the title by moving up to the field
where the title number is shown with Arrow (
K),
and entering a title number of your choice.
3 Press ENTER or PLAY.
¡Playback of the selected chapter will start.
DVD
Notes
¡Pressing DISC NAVIGATION before pressing ENTER or
PLAY at step 3 will cease the DISC NAVIGATION func-
tion, and the playback will be stopped. The resume infor-
mation will be lost.
¡When a disc menu is shown, the DISC NAVIGATION fea-
ture does not function.
¡DISC NAVIGATION takes a few seconds to respond.
¡With some discs, part of the DISC NAVIGATION screen
may not be displayed properly. This is not a malfunction.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 23
–
24
–
EN
1L25
TITLE MENU
1 Press TOP MENU.
¡The title menu will appear.
2 If the feature is not available, symbol
may appear on the TV screen.
3 Press Arrow (L/K/B/s) to select an item,
and ENTER to confirm selection.
DVD
STEP BY STEP PLAYBACK
1 During playback, press PAUSE/STEP.
¡Playback will pause and sound will be muted.
2 The disc goes forward by one frame each
time PAUSE/STEP is pressed.
3 To exit step by step playback, press PLAY.
Note
¡The resume playback takes a little longer to take
place compared to the normal playback.
DVD
RESUME
1 During playback, press STOP.
¡Resume message will appear on the TV screen.
2 Press PLAY, playback will resume from the
point at which playback was stopped.
¡To cancel resume, press STOP twice.
¡If turn off the DVD/VCR, resume function can-
celled.
CD
DVD
DISC MENU
1 Press MENU.
¡The DVD main menu will appear.
2 If the feature is not available, symbol
may appear on the TV screen.
3 If disc menu is available on the disc, audio
language, subtitle options, chapters for the
title and other options will appear for selec-
tion.
4 Press Arrow (L/K/B/s) to select an item,
and ENTER to confirm selection.
DVD
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVDs
¡Press MENU to call up the DVD menu.
¡Press TOP MENU to call up the title menu.
Note
¡Contents of menus and corresponding menu opera-
tions may vary between discs. Refer to the manual
accompanying the disc for details.
1 During playback, press g or h repeat-
edly to select the required forward or
reverse speed: x2, x8, x50, x100.
¡For audio CDs, the speed is fixed at ×16.
¡For MP3, the speed is fixed at ×8.
2 To return to normal playback, press PLAY.
MP3CD
DVD
FAST FORWARD/REVERSE
SEARCH
SLOW FORWARD /
SLOW REVERSE
1 During playback, press PAUSE/STEP.
2 Press g or h .
3 Press g or h repeatedly to select the
required speed: 1/16, 1/8, 1/2 of the normal
playback.
4 To return to normal playback, press PLAY.
¡Slow playback is not available with audio CDs.
DVD
PAUSE
1 During playback, press PAUSE/STEP.
¡Playback will pause and sound will be muted.
2 To continue playback, press PLAY.
CD
DVD
H9451UD(EN).qx33 03.1.22 7:22 PM Page 24
–
25
–
EN
1L25
English
TRACK
There are three ways to begin playback on an Audio
CD at a specific Track.
Using the Numerical buttons
1 Press Numerical buttons to enter the
desired Track number.
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡To play track 26, press +10, 2, 6 on the numerical
button.
Using SEARCH MODE
1 Press SEARCH MODE.
¡The track search display appears.
2 Within 30 seconds, select a desired track
number using numerical buttons.
¡For single digits press 0 first.
¡Playback will start at the selected track.
¡Press CLEAR/C.RESET to erase the incorrect input.
CD
ZOOM
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
1 Press ZOOM during playback.
¡Playback will continue.
2 Press ZOOM repeatedly to select the
required zoom factor: x2, x4 or OFF.
3 Use the Arrow (K/L/s / B) to move the
zoomed picture across the screen.
4 To exit zoom mode, press ZOOM to OFF.
Notes
¡Zooming function does not work while disc menu is
shown.
¡x4 zoom is not available on some discs.
DVD
Using SKIP
H
,
G
During playback, press SKIP G to move the next
track. Press it repeatedly to skip subsequent tracks.
Press SKIP H to go back to beginning of the current
track. Press it repeatedly to go to the previous tracks.
¡Track number will appear briefly on the DVD/VCR
display panel.
¡If SKIP is pressed while the playback is paused, the
playback will be paused again after skipping to the
next track.
Note
¡SKIP HGare not available when playback is
stopped.
TITLE / CHAPTER SEARCH
1 Press SEARCH MODE once for the Chapter
search, twice for the Title search during
playback.
2 Enter the desired chapter/title number using
numerical buttons.
¡Playback will start at the selected Chapter or Title.
¡Press CLEAR/C.RESET to erase the incorrect input.
¡For single digits press 0 first.
DVD
/2
TIME SEARCH
1 During playback, press SEARCH MODE
three times (CD: twice) to display the Time
Search on the TV screen.
2 Within 30 seconds, enter a desired disc
time using numerical buttons.
¡Playback will start at the specified time.
3 Press CLEAR/C.RESET to erase the incor-
rect input.
CD
DVD
H9451UD(EN).qx33 03.1.22 7:22 PM Page 25
–
26
–
EN
1L25
REPEAT TRACK
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
CD
TRACK ALL OFF
(current track repeat) (entire disc repeat)
(repeat off)
Notes
¡Track repeat setting will be cleared when moving to
other track.
¡Repeat playback does not function during A-B
REPEAT playback.
A-B REPEAT
1 Press A-B REPEAT at your chosen starting
point.
¡ A- appears briefly on the TV screen.
2 Press A-B REPEAT again at your chosen
end point.
¡ A-B appears briefly on the TV screen, and the
repeat sequence begins.
3 To exit the sequence, press A-B REPEAT.
Notes
¡The A-B REPEAT section can only be set within the
current title (for DVDs), or current track (for audio
CDs).
¡A-B REPEAT is not available with some scenes in
DVD.
¡To cancel the A point which was set, press
CLEAR/C.RESET.
¡A-B REPEAT playback does not function during
title, chapter, track or all repeat playback.
CD
DVD
MARKER SETUP SCREEN
Use markers to memorise your favourite places on a
disc.
1 Press SEARCH MODE four times (CD: three
times) during playback.
¡The display screen and Markers will appear on the
TV screen.
2 Press Arrow (s/ B) to select 1, 2, 3, 4, 5, 6,
7, 8, 9, or 10 and ensure that “- :- - :- -”
appears in the display.
3 When reaches the desired point, press
ENTER.
¡The Title or Track and elapsed playing time will
appear in the TV screen.
4 To return to the Marker later, press SEARCH
MODE four times (CD: three times) during
playback and Arrow (
s/ B) to choose the
desired marker, then press ENTER.
Notes
¡Opening the disc tray or turning off the power or
select AC at step 2 and press ENTER will erase all
Markers.
¡To clear a marker, using Arrow (s / B
)
, position the
cursor on to the marker number to be cleared and
press CLEAR/C.RESET.
¡You can mark up to 10 points.
5 Press SEARCH MODE or RETURN to exit.
CD
DVD
REPEAT
REPEAT TITLE / CHAPTER
To activate the repeat function, press REPEAT
during playback.
¡The repeat mode changes as described below every
time you press the button.
DVD
REPEAT is available only during playback.
CHAPTER TITLE OFF
(current chapter repeat) (current title repeat)
(repeat off)
Notes
¡Track Repeat Title/Chapter is not available with
some scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
MP3
TRACK GROUP OFF
(current track
repeat)
(current folder
repeat)
(repeat off)
ALL
(entire disc
repeat)
H9451UD(EN).qx33 03.1.22 7:22 PM Page 26
–
27
–
EN
1L25
English
RANDOM PLAYBACK
This shuffles the playing order of tracks instead of
playback in the original sequence.
1 In stop mode, press MODE twice.
¡RANDOM screen
appears.
2 Press PLAY to start random playback.
Note
¡If you like to repeat the current track in the random
selection, press REPEAT repeatedly until
TRACK appears during playback. If you like to
repeat the entire random selection press REPEAT
repeatedly until ALL appears during playback.
CD
PLAY
CD [AUDIO] TOTAL 0:45:55
RANDOM PROGRAM
--no indication--
RANDOM
When a CD with MP3 files is inserted in the
DVD/VCR, the MP3 menu will appear on the TV
screen, and number of tracks is displayed on the front
panel.
1 In stop mode, press Arrow (K/L) to select
the desired group track.
¡If a group is selected,
press
B
or ENTER to go
on to the track selection
screen. Press Arrow (K/L)
to choose a track, then
press
B
or ENTER.
¡If a track is selected, press
B
or ENTER to start playing tracks. Starting from
the one you’ve just chosen the subsequent tracks will
be played.
¡Choose FIRST PLAY to start playback from the
beginning of the listed tracks.
¡Press TOP MENU to return to the first item.
2 Press STOP to stop playback.
MP3
MP3 PLAYBACK
–
28
–
EN
1L25
RANDOM PLAYBACK
1 Press MODE twice while playback is
stopped.
2 Press PLAY to play the tracks in random
order.
MP3
This feature allows you to program a mp3 disc to play
in a desired sequence.
1 Press MODE during playback is stopped.
¡The PROGRAM screen will appear.
2 Press Arrow (K/L) to select a track, then
press ENTER, to save it in a program.
¡Press CLEAR/C.RESET to erase the incorrect input.
3 Press PLAY to start programmed playback.
MP3
PROGRAM
AUDIO LANGUAGE
The DVD/VCR allows you to select a language during
DVD disc (if multi language available) playback.
1 Press AUDIO during playback.
2 Press AUDIO repeatedly to select your
desired language.
Notes
¡Pressing AUDIO may not work on some DVDs with
multiple audio languages (e.g. DVDs which allow
audio language setting on the disc menu).
DVD
STEREO SOUND MODE
1 Press AUDIO repeatedly during playback to
select between STEREO, L-CH or R-CH.
¡STEREO - both right and left channels are active
(stereo)
L-CH - only left channel is active
R-CH - only right channel is active
Note
¡If the Virtual Surround setting is 1 or 2, the sound
mode will be fixed to STEREO, and can not be
changed.
¡If you use DIGITAL AUDIO OUT jack, the sound
mode of Audio CDs can not be changed.
CD
Notes
¡Folders are known as Groups; files are known as
Tracks.
¡MP3 files are accompanied by icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 256 files can be recognized.
¡Up to 8 hierarchies can be created.
This player recommends the use of files recorded at the
below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
3
ON-SCREEN
INFORMATION
You can check the MP3 files during playback.
1 Press DISPLAY.
¡The name of the file currently in play will be dis-
played.
2 Press DISPLAY again to show the track
number, the repeat status, and the playback
status at the top of the screen.
¡ will be displayed when repeat play has been
selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates ALL repeat
3 Press DISPLAY again to exit.
MP3
1 Press SEARCH MODE during playback.
¡The FILE LIST will appear.
2 Select a desired track using Arrow
(
K/L/s/B).
¡Press B when you want to go to the next hierarchy.
¡Press s when you want to go back to the previous
hierarchy.
3 Press PLAY to start playing.
Notes
¡Press SEARCH MODE to EXIT.
¡Some selections may take a while to be recognized.
MP3
TRACK SELECTION
H9451UD(EN).qx33 03.1.22 7:22 PM Page 28
–
29
–
EN
1L25
English
CHANGING THE ON-SCREEN
DISPLAY
You can check the information about the current disc
by pressing DISPLAY on the remote control.
For DVDs
1 Press DISPLAY during playback to show
current Chapter.
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
2 Press DISPLAY again to show current Title.
¡The elapsed and remaining playing time of the cur-
rent title will be displayed.
3 Press DISPLAY third time.
¡The BIT RATE and the current repeat setting will be
displayed.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
4 Press DISPLAY the fourth time to remove
the display.
For audio CDs
1 Press DISPLAY during playback, the current
Track will be displayed on the TV screen.
¡The elapsed and remaining playing time of the cur-
rent track will be displayed.
2 Press DISPLAY again to show current Total
Track.
¡The elapsed and remaining playing time of the cur-
rent total track will be displayed.
3 Press DISPLAY third time to remove the dis-
play.
CD
DVD
9/49 0:00:00 -0:00:00
The DVD allows you to select a language for subtitles
during DVD disc (if available) playback.
1 Press SUBTITLE during playback.
2 Press SUBTITLE repeatedly to select your
desired subtitle language.
¡The subtitle language will be displayed on the dis-
play bar at the top of the screen.
3 To turn off subtitles, press SUBTITLE
repeatedly until OFF appears.
Notes
¡Some discs allow audio language setting/subtitle
language setting on the disc menu. (Operation varies
between discs, so refer to the manual accompanying
the disc.)
¡If the desired language is not shown after pressing
SUBTITLE several times, the disc does not have
subtitles in that language.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 32.)
¡ It may take time to display the subtitles in the
selected language.
DVD
SUBTITLE LANGUAGE
CAMERA ANGLE
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change
the camera angle when the ( ) mark appears on the
screen.
1 Press ANGLE during playback.
¡The selected angle will be displayed on the display
bar at the top of the screen.
2 Press ANGLE repeatedly to select your
desired angle.
DVD
PARENTAL CONTROL
Parental Control limits the disc viewing that exceed
your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alterna-
tive scenes from being played by your children.
DVD
PARENTAL LEVEL
Parental Level allows you to set the rating level of your
DVD discs. Playback will stop if the disc’s ratings
exceed the level you set.
1 Press SETUP in STOP mode.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 29
–
30
–
EN
1L25
CONTROL LEVELS
¡
ALL
All parental lock is cancelled.
¡
Level 8
DVD software of any grade (adult/general/children)
can be played back.
¡
Levels 7 to 2
Only DVD software intended for general use and
children can be played back.
¡
Level 1
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
DVD SETUP
AUDIO SETTINGS
Choose the appropriate Audio settings for your equip-
ment as it only affect during the playback of DVD
discs.
1 Press SETUP in STOP mode.
2 Press B to select CUSTOM, then press
ENTER.
¡CUSTOM mode will appear.
3 Press Arrow (s/ B) to select AUDIO, then
press ENTER to con-
firm.
4 Press Arrow (K/L) to select the below
items, then press ENTER.
DRC (Dynamic Range Control):
¡To compress the range of sound volume.
¡The default setting is OFF.
¡This function is effective only for the sound record-
ed by Dolby Digital recording.
Dolby Digital:
Set to BITSTREAM when the unit is connected to a
Dolby Digital Decoder.
(BITSTREAM: Output by Dolby Digital)
(PCM: Convert the Dolby Digital to PCM)
¡The default setting is BITSTREAM.
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be acti-
vated and sound will be down sampled at 48kHz.
4 Press SETUP to exit.
QUICK
AUDIO
DRC OFF
DOLBY DIGITAL BITSTREAM
DOWN SAMPLING ON
2 Press B to select CUSTOM, then press
ENTER.
3 Press Arrow (s/B) to select PARENTAL,
then press ENTER.
4 Enter your four-digit password then press
ENTER.
5 Press Arrow (K/L) to select PARENTAL
LEVEL, then press ENTER.
6 Press Arrow (K/L) to select the desired
level.
7 Press SETUP to exit
Notes
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password from the second time onward.
¡To change the password, press Arrow (K/L) to
select CHANGE, then press ENTER. Enter the four-
digit pass-word, then press ENTER.
PARENTAL
PARENTAL LEVEL ALL
IF YOU FORGET THE PASSWORD
1 Press 4, 7, 3, 7 at step 4.
¡Password will be cleared and parental level will be
set to ALL.
2 Proceed the above Steps 4-6 again.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 30
–
31
–
EN
1L25
English
Adjust the Black Level Settings to make the black
parts of the picture as bright as you preferred.
1 Press MODE during playback.
2 Press ENTER to switch ON/OFF.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
3 Press MODE twice or RETURN to exit.
DVD
BLACK LEVEL SETTING
You can enjoy stereophonic visual space on your exist-
ing stereo system.
1 Press SURROUND during playback.
2 Press SURROUND to set it 1 (Natural effect)
or 2 (Emphasized effect) or OFF.
3 Press MODE or RETURN to exit.
Note (for CD play only)
¡Virtual Surround will not be effective if the sound
mode is set to something other than STEREO.
MP3CD
DVD
VIRTUAL SURROUND
ON
OFF
You can change certain aspects of the DVD display
screens, on-screen messages and the display panel on
the front of the DVD/VCR.
1 Press SETUP in STOP mode.
2 Press B to select CUSTOM, then press
ENTER.
¡CUSTOM mode will appear.
3 Press Arrow (s/ B) to select DISPLAY, then
press ENTER to con-
firm.
4 Press Arrow (K/L) to select the below
items, then press ENTER.
TV ASPECT:
¡Press Arrow (K/L) for an item selection, then press
ENTER.
¡Select 4:3 LETTER BOX for a black bars appears on
top and bottom of the screen.
¡Select 4:3 PAN - SCAN for a full height picture with
both sides trimmed.
¡Select 16:9 WIDE if a wide-screen TV is connected
to the DVD/VCR.
¡The default setting is 4:3 LETTER BOX.
ANGLE MARK:
¡Press ENTER repeatedly to turn Angle mark ON or
OFF.
¡The default setting is ON.
AUTO POWER OFF:
¡Press ENTER repeatedly to turn Auto Power off ON
or OFF.
¡The default setting is ON and it will turn the
DVD/VCR to off automatically after 35 minutes of
no use.
LOGO:
¡Press ENTER to switch ON (opening picture)/
OFF(black).
¡The default setting is ON.
5 Press SETUP to exit.
Notes
¡Be sure to press SETUP, or the setting will not work.
QUICK
DVD
DISPLAY SETTING
DISPLAY
TV ASPECT
4:3 L- BOX
ANGLE MARK ON
AUTO POWER OFF ON
LOGO ON
H9451UD(EN).qx33 03.1.22 7:22 PM Page 31
–
32
–
EN
1L25
–
32
–
EN
1L25
Language options are not available with some discs.
1 Press SETUP in STOP mode.
2 Press B to select CUSTOM, then press
ENTER.
¡CUSTOM mode will appear.
3 Press Arrow (s/ B) to select LANGUAGE,
then press ENTER to
confirm.
4 Press Arrow (K/L) to select the below
items, then press ENTER.
¡If you want to return to LANGUAGE SETTING
MENU, press Arrow(s ).
DVD
LANGUAGE SETTING
LANGUAGE
AUDIO ORIGINAL
SUBTITLE OFF
DISC MENU ENGLISH
PLAYER MENU ENGLISH
A-B
Abkhazian 4748
Afar 4747
Afrikaans 4752
Albanian 6563
Amharic 4759
Arabic 4764
Armenian 5471
Assamese 4765
Aymara 4771
Azerbaijani 4772
Bashkir 4847
Basque 5167
Bengali;Bangla 4860
Bhutani 5072
Bihari 4854
Bislama 4855
Breton 4864
Bulgarian 4853
Burmese 5971
Byelorussian 4851
C-E
Cambodian 5759
Catalan 4947
Chinese [CHI] 7254
Corsican 4961
Croatian 5464
Czech 4965
Danish [DAN] 5047
Dutch [DUT] 6058
English [ENG] 5160
Esperanto 5161
Estonian 5166
F-H
Faroese 5261
Fiji 5256
Finnish [FIN] 5255
French [FRE] 5264
Frisian 5271
Galician 5358
Georgian 5747
German [GER] 5051
Greek [GRE] 5158
Greenlandic 5758
Guarani 5360
Gujarati 5367
Hausa 5447
Hebrew 5569
Hindi 5455
Hungarian [HUN] 5467
I-K
Icelandic [ICE] 5565
Indonesian 5560
Interlingua 5547
Interlingue 5551
Inupiak 5557
Irish [IRI] 5347
Italian [ITA] 5566
Japanese [JPN] 5647
Javanese 5669
Kannada 5760
Kashmiri 5765
Kazakh 5757
Kinyarwanda 6469
Kirghiz 5771
Kirundi 6460
Korean [KOR] 5761
Kurdish 5767
L-N
Laothian 5861
Latin 5847
Latvian;Lettish 5868
Lingala 5860
Lithuanian 5866
Macedonian 5957
Malagasy 5953
Malay 5965
Malayalam 5958
Maltese 5966
Maori 5955
Marathi 5964
Moldavian 5961
Mongolian 5960
Nauru 6047
Nepali 6051
Norwegian [NOR] 6061
O-R
Occitan 6149
Oriya 6164
Oromo(Afan) 6159
Panjabi 6247
Pashto;Pushto 6265
Persian 5247
Polish 6258
Portuguese [POR] 6266
Quechua 6367
Rhaeto-Romance 6459
Romanian [RUM] 6461
Russian [RUS] 6467
S
Samoan 6559
Sangho 6553
Sanskrit 6547
Scots Gaelic 5350
Serbian 6564
Serbo-Croatian 6554
Sesotho 6566
Setswana 6660
Shona 6560
Sindhi 6550
Singhalese 6555
Siswat 6565
Slovak 6557
Slovenian 6558
Somali 6561
Spanish [SPA] 5165
Sundanese 6567
Swahili 6569
Swedish [SWE] 6568
T
Tagalog 6658
Tajik 6653
Tamil 6647
Tatar 6666
Telugu 6651
Thai 6654
Tibetan 4861
Tigrinya 6655
Tonga 6661
Tsonga 6665
Turkish [TUR] 6664
Turkmen 6657
Twi 6669
U-Z
Ukrainian 6757
Urdu 6764
Uzbek 6772
Vietnamese 6855
Volapuk 6861
Welsh 4971
Wolof 6961
Xhosa 7054
Yiddish 5655
Yoruba 7161
Zulu 7267
Language Code Language Code Language Code Language Code
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change
the Audio or Subtitle language setting on pages 28 and 29. If you choose any other languages, ‘---’ will be
displayed instead. (3 letter language code is written in bracket.)
AUDIO:
¡Sets the audio language.
SUBTITLE:
¡Sets the subtitle language.
DISC MENU:
¡Sets the language for DVD menu.
PLAYER MENU:
¡Sets the language for the On-screen display.
5 Press Arrow (K/L) to select a setting, then
press ENTER.
¡If OTHERS is selected on the AUDIO, SUBTITLE
–
33
–
EN
1L25
English
TROUBLESHOOTING GUIDE
If the DVD/VCR does not perform properly when operated as instructed in this Owner's Manual, check the
DVD/VCR consulting the following checklist.
V
C
R
D
V
D
V
C
R
D
V
D
PROBLEM CORRECTIVE ACTION
No power. • Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
The DVD/VCR does not respond • Check if the power plug is connected to an AC outlet.
to the remote control. • Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles
between the sensor and the remote.
• You have to be within 23 feet of the DVD/VCR.
• Check if the correct mode is selected. If not switch the mode by pressing DVD or VCR
,whichever you need, on the remote control.
• Check if a cassette tape is in the VCR.
Timer recording is impossible. • Make sure the timer recording is set correctly.
• Make sure the DVD/VCR clock is set correctly.
Cannot go into Record mode. • Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
• Put the DVD/VCR in VCR mode. Press VCR on the remote control so that the green VCR OUT-
PUT light is lit.
Playback picture is partially noisy
• Adjust tracking control for a better picture by pressing CHANNEL (o /p) on the DVD/VCR.
Cannot view a tape but the • Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
audio is OK
.
• Make sure the DVD/VCR is not in the Menu mode.
No, or poor, playback picture. • Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
TV programs cannot be seen • Re-check the ANT. IN and ANT. OUT connections. See page 13.
normally.
• Press VCR/TV.
• Press VCR on the remote control to put it in the VCR mode. Check if the green VCR OUTPUT
light is lit. Then, set it to the TV position by pressing VCR/TV.
Video or color fades in and out •
You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
when making a copy of a video tape.
Cannot remove the tape. • Check if the DVD/VCR is in the VCR mode. If not, press VCR on the remote control to switch the
mode.
No picture. • Connect the video cables firmly.
• Insert a correct video disc that plays on this DVD/VCR.
• Press DVD on the remote control. Check if the DVD OUTPUT Light is lit. Then try other DVD
feature.
• Check if the progressive switch is set correctly according to your TV.
Disc cannot be played
. • Insert the disc.
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
No sound
. • Connect the audio cables firmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
No DTS audio is output
. • This DVD/VCR does not support DTS audio. This is not a malfunction.
Distorted picture
. • Connect the DVD/VCR directly to the TV.
•
There are some cases where pictures may be slightly distorted, which are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language •
The selected language is not available for audio or subtitles on the DVD disc.
does not match the set up.
This is not a malfunction
The camera angle cannot be •
The DVD disc does not
contain sequences recorded from different camera angles.
changed.
This is not a malfunction
Audio or subtitle language • The DVD disc does not contain audio source or subtitles in the selected language.
cannot be changed.
This is not a malfunction.
“Prohibited icon” appears on the • That operation is prohibited by the DVD/VCR or the disc.
screen, prohibiting an operation.
This is not a malfunction.
Notes
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this
Owner’s Manual for details on correct operations.
¡Playback from a desired track and random playback are not available during program playback.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 33
–
34
–
EN
1L25
MAINTENANCE
SERVICING
¡Should your DVD/VCR become inoperative, do not
try to correct the problem by yourself. There are no
user-serviceable parts inside. Turn off, unplug the
power cord, and please call our help line at 1-800-
448-2244 to locate an Authorized Service Center.
CLEANING THE CABINET
¡Use a soft cloth slightly moistened with a mild deter-
gent solution. Do not use a solution containing alco-
hol, spirits, ammonia or abrasives.
CLEANING DISCS
¡When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe
in a circular motion.
¡Do not use solvents such as benzine, thinner, com-
mercially available cleaners, detergent, abrasive
cleaning agents or antistatic spray intended for ana-
logue records.
CLEANING THE DISC LENS
¡If the DVD/VCR still does not perform properly
when it is operated while referring to the relevant
sections and to “TROUBLESHOOTING GUIDE” in
this Owner’s Manual, the laser optical pickup unit
may be dirty. Consult your dealer or an Authorized
Service Center for inspection and cleaning of the
laser optical pickup unit.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or remove a cas-
sette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while the TV
program reception is clear. Dirt accumulated on the video heads
after long periods of use, or the usage of rental or worn tapes can
cause this problem. If a streaky or snowy picture appears during
playback, the video heads in your DVD/VCR may need to be
cleaned.
1. Please visit your local Audio/Video store and purchase a good
quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem, please call
our help line at 1-800-448-2244 to locate an Authorized Service
Center.
NOTES:
• Remember to read the instructions included with the video head
cleaner before use.
• Clean video heads only when problems occur.
RecordableRecordable
ReWritableReWritable
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special waste.
Contact your council for details.
DISC HANDLING
¡Use discs which have the following logos on them.
(Optical audio digital discs.)
¡Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
¡Always store the disc in its protective case when it is
not used.
¡To clean-off, use a soft cloth.
¡Do not use a hard cloth since this will mar the disc.
¡Wipe the disc in a straight line from center to edge.
¡Never wipe with a circular motion.
¡Do not use detergent or abrasive cleaning agents.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 34
–
35
–
EN
1L25
English
SPECIFICATIONS
Product type: DVD/VCR Combo (DVD player with Video Cassette Recorder)
Discs: DVD video
Audio CD
Video Cassette tape
Converter output: VHF Channel 3 or 4.
Power source: 120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption: 24 W (standby: 7.0 W)
Operating temperature: 41°F(5°C) to 104°(F40°C)
Dimensions: W 17-1/8” (435 mm)
H 3-7/8” (99 mm)
D 8-5/8” (218 mm)
Weight: 8.1 lbs (3.7 kg)
¡Designs and specifications are subject to change without notice.
¡If there is a discrepancy between languages, the default language will be English.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 35
–
36
–
SP
1L25
CONTROLES DEL FUNCIONAMIENTO Y SUS FUNCIONES
POWER/STANDBY
CHANNEL
PLAYSTOP/EJECT
VIDEO IN
F. F W DREWREC/IRT
TIMER REC
DVD OUTPUT VCRSTOP PLAY
OPEN/CLOSE
L
(mono)
AUDIO IN R
LINE 2
1 342
6810121420
791113171921 15
5
18 16
PANEL DELANTERO
PANEL REMOTO
+10
EJECT
3
MODE
2
SEARCH
OPEN/CLOSE
9
ZOOM
DISPLAY
8
AUDIO
0
TOP MENU
SETUP
PLAY
SKIP
CH
CH
56
1
A-B REPEAT
REPEAT
7
CLEAR/C. RESET
SUBTITLE/TIMER
MODE
ANGLE
DVD VCR/TV
DISC
NAVIGATION
VCR
SLOW SPEED REC
RETURN
MENU
STOP
TV POWER
VIDEO/TV
4
SURROUND
PAUSE/STEP
VOL
TV
ENTER
23
22
24
25
26
27
28
29
30
31
33
32
34
58
59
57
54
53
55
56
36
39
38
51
49
50
52
48
47
40
41
42
46
45
44
43
37
35
1. Bandeja de carga del disco
2. Botón OPEN/CLOSE
Presione para insertar discos en o removerlos de la bandeja
de carga del disco.
3. COMPARTIMIENTO DE CASETES
4. Luz POWER
Se enciende cuando la alimentación está conectada.
5. Botón POWER/STANDBY
Presione para conectar y desconectar la alimentación.
6. Botones CHANNEL
En el modo VCR, presione para cambiar canales de TV en la
videograbadora; presione para ajustar el seguimiento durante
la reproducción normal o en movimiento lento; presione para
remover las fluctuaciones verticales en una imagen fija.
7. Botón PLAY (VCR)
Presione para comenzar la reproducción.
8. Botón STOP/EJECT (VCR)
Botón de expulsion (EJECT)
Presione para sacar la cinta de la videograbadora.
Botón de parada (STOP)
Presione para detener el movimiento de la cinta.
9. Toma de entrada de AUDIO
Conecte aquí cables de audio procedentes de las tomas de
salida de audio de un camcorder, otra videograbadora o una
fuente de video.
10. Toma de entrada de VIDEO
Conecte aquí un cable de video procedente de la toma de
salida de video de un camcorder, otra videograbadora o una
fuente de video (reproductor de discos láser, camcorder, etc.)
11. Botón F.FWD (VCR)
Presione para avanzar rápidamente la cinta o ver la imagen
rápidamente en avance durante la reproducción (Búsqueda en avance).
12. Botón REW (VCR)
Presione para rebobinar la cinta o para ver la imagen
rápidamente en inversión durante el modo de reprodución
(Búsqueda en rebobinado).
13. Botón REC/IRT
Presione una vez para comenzar la grabación. Presione
repetidamente para comenzar una grabación instantánea.
14. Luz REC
Se enciende durante la grabación.
15. Luz TIMER
Esta luz se enciende cuando el DVD/VCR está en el modo
de espera o apagada para una grabación con temporizador
o durante una grabación instantánea. Parpadea si se
presiona el TIMER para una grabación con temporizador
pero no hay cinta en el DVD/VCR. Parpadea cuando todas
las grabaciones con temporizador o grabaciones
instantáneas han terminado.
16. Luz VCR OUTPUT (verde)
Esta luz aparece cuando se selecciona el modo VCR. Usted
sólo puede mirar cintas cuando la luz VCR OUTPUT verde
esta encendida. Para hacer que la luz VCR OUTPUT verde
se encienda, presione el VCR en el control remoto o el
OUTPUT en el panel delantero.
17. Botón OUTPUT
Presione para seleccionar el modo DVD o el modo VCR.
●
Usted puede cambiar el modo de salida ya sea presionando
el OUTPUT en el panel delantero o el DVD o VCR en el
control remoto. Sin embargo,
si usted presiona el
OUTPUT en el panel delantero primero, usted necesita
volver a seleccionar el modo correspondiente
presionando el DVD o el VCR en el control remoto.
18. Luz DVD OUTPUT (verde)
Esta luz aparece cuando se selecciona el modo DVD. Usted
sólo puede mirar DVDs cuando la luz DVD OUTPUT
verde se encienda. Para que se encienda la luz DVD
OUTPUT verde, presione el DVD en el control remoto o el
OUTPUT en el panel delantero.
19. Visualizador, ventanilla del sensor remoto
20. Botón PLAY (DVD)
Presione para comenzar la reproducción.
21. Botón STOP (DVD)
Detiene la operación del disco.
22. Botón SURROUND
Presione para activar el sonido tridimensional.
23. Botón
yy
/I (POWER/STANDBY)
Presione para conectar y desconectar la alimentación.
(Para las indicaciones del interruptor de funcionamiento,
“I” indica la conexión y “
yy
/I” indica el estado de espera
de alimentación eléctrica.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 36
Español
–
37
–
SP
1L25
24. Botón A-B REPEAT
Cepite la reproducción de una sección seleccionada.
25. Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
26. Botón MODE
Activa el modo de reproducción de progama o
reproducción aleatoria cuando se reproducen CDs o MP3.
Ajusta el nivel del negro y el Virtual Surround.
27. Botón ZOOM
Amplía parte de una imagen reproducida en DVD.
28. Botón CREAR/C.RESET
●
Modo DVD
Presione para reponer el ajuste.
●
Modo VCR
Presione para reponer el contador. Presione para salir de
la pantalla MENU.
29. Botón ANGLE
Presione para cambiar el ángulo de cámara para ver la secuencia
que se está reproduciendo desde un ángulo diferente.
30. Botón SUBTITLE
Presione para seleccionar un idioma de subtítulo deseado.
30. Botón TIMER
Presione para poner la videograbadora en el modo de
espera para una grabación con temporizador.
31. Botón MENU
●
Modo DVD
Presione para visualizar el menú del disco.
●
Modo VCR
Presione para tener acceso al menú VCR.
32. Botones de flecha
● Modo DVD
32. Botones p
/
o
/
B
/
s
Mueve el cursor y determina su posición.
● Modo VCR
32. Botones p
/
o
Presione para entrar dígitos cuando ajuste el programa. (Por
ejemplo, ajuste el reloj o programa con temporizador.) Presione
para seleccionar los modos de ajuste del menú en pantalla.
Botón B
Cuando ajuste el programa (Por ejemplo: ajuste el reloj o
programa con temporizador), presione para determinar su
selección y proceder al siguiente paso que usted desea
entrar. Presione para determinar los modos de ajuste del
menú en pantalla. Presione para añadir o cancelar números
de canal durante el preajuste de canal.
Botón s
Presione para cancelar un ajuste de programa con
temporizador. Presione para corregir dígitos cuando ajuste
el programa. (Por ejemplo: ajuste de reloj o programa con
temporizador.) Presione para añadir o cancelar números de
canal durante el preajuste de canal.
33. Botón ENTER
Presione para aceptar un ajuste.
34. Botón RETURN
Vuelve a la operación previa.
35. Botón VCR/TV
Utilice para seleccionar la posición VCR o TV.
Este DVD/VCR no tiene una luz VCR/TV. Si aparece ruido
en su TV cuando enciende el DVD/VCR (modo VCR),
presione este botón.
●
Posición VCR
Para mirar la reproducción, para monitorear las
grabaciones de video o para mirar un TV utilizando el
sintonizador VCR.
●
Posición TV
Para mirar la TV o para mirar un programa mientras
graba otro.
36. Botón DVD
Presione antes de utilizar el control remoto para el modo DVD.
●
Usted puede cambiar el modo de salida ya sea presionando
el OUTPUT en el panel delantero o el DVD o VCR en el
control remoto. Sin embargo,
si usted presiona el
OUTPUT en el panel delantero primero, usted necesita
volver a seleccionar el modo correspondiente
presionando el DVD o el VCR en el control remoto.
37. Botón SLOW
Durante la reproducción de la cinta, presione para mirar la
cinta de video en movimiento lento. Presione de nuevo
para reanudasr la reproducción normal. Este botón no
afecta la reproducción de DVD.
38. Botones SKIP
●
Modo DVD
Presione para saltar capítulos o pistas.
39. Botón STOP
●
Modo DVD
Presione para detener el movimiento del disco.
●
Modo VCR
Presione para detener el movimiento de la cinta.
40. Botón h
●
Modo DVD
Presione para ver la imagen DVD en movimiento de
inversión rápida o para inversión rápida o para invertir la
reproducción de un CD de audio.
●
Modo VCR
Presione para rebobinar la cinta o para ver la imagen
rápidamente en inversión durante el modo de
reproducción (Búsqueda en Rebobinado).
41. Botón TV POWER
Exclusivamente para encender/apagar el TV.
42. Botón VIDEO/TV
Presione para seleccionar el modo de entrada externa o
modo de TV en el televisor.
43. Botones VOL
Presione para controlar exclusivamente el volumen de TV.
44. Botones TV CH p
/
o
Presione para controlar exclusivamente los canales de TV.
45. Botón PAUSE/STEP
●
Modo DVD
Presione para hacer una pausa en la reproducción del
disco. Presione repetidamente para avanzar la imagen
DVD paso a paso (o un fotograma a cada vez).
●
Modo VCR
Mientras graba, presione para detener provisionalmente
la grabación (pausa). Presione por segunda vez para
reanudar la grabación normal. Usted no puede hacer una
pausa en la grabación instantánea. O presione durante la
reprodución de la cinta para congelar la imagen.
46. Botón g
●
Modo DVD
Presione para avanzar rápidamente el disco. Presione el
PAUSE/SETP, luego presione este botón para comenzar
la reproducción en movimiento lento. Presione este
botón repetidamente para cambiar la velocidad de
avance del movimiento lento.
●
Modo VCR
Presione para avanzar rápidamente la cinta o ver la
imagen rápidamente en avance durante la reproducción
(Búsqueda de avance).
47. Botón PLAY
●
Modo DVD
Presione para comenzar la reproducción.
●
Modo VCR
Presione para comenzar la reproducción.
48. Botones CH
●
Modo VCR
Presione para cambiar canales de TV en la videograbadora.
49. Botón REC
Presione una vez para comenzar una grabación.
(
)
H9451UD(EN).qx33 03.1.22 7:22 PM Page 37
–
38
–
SP
1L25
50. Botón SPEED
Presione para seleccionar la velocidad de grabación de
VCR (SP o SLP).
51. Botón VCR
Presione para seleccionar el modo VCR para el control remoto.
●
Usted puede cambiar el modo OUTPUT ya sea presionando
el OUTPUT en el panel delantero o el DVD o VCR en el
control remoto. Sin embargo,
si usted presiona el
OUTPUT en el panel delantero primero, usted necesita
volver a seleccionar el modo correspondiente
presionando el DVD o el VCR en el control remoto.
52. Botón SETUP
Presione para entrar en el modo de preparación.
53. Botón DISC NAVIGATION
Púlselo para visualizar las primeras ascenas de cada
capítulo del título que astá siendo reprocido.
54. Botón TOP MENU
Presione para llamar el menú de título.
55. Botón DISPLAY
●
Modo DVD
Presione para tener acceso o remover la pantalla de
visualización durante la reproducción DVD o CD de audio.
●
Modo VCR
Presione para tener acceso o remover la visualización de
estado en pantalla de la videograbadora.
56. Botón AUDIO
Presione para seleccionar un idioma de audio deseado o
modo de sonido.
57. Botones numéricos
●
Modo DVD
Presione para seleccionar directamente una pista (CD de
audio) para su reproducción.
●
Modo VCR
Presione para seleccionar canales de TV en la videograbadora.
Para seleccionar canales, entre el número de canal como
un número de dos dígitos para los resultados más
rápidos. Por ejemplo, para seleccionar el canal 6,
presione 0 y después 6.
58. Botón OPEN/CLOSE
Presione para abrir o cerrar la bandeja de carga del disco.
58. Botón EJECT
Presione para que salga el videocasete de la videograbadora.
59. Botón SEARCH MODE
●
Modo DVD
Presione para tener acceso o remover la indicación de
búsqueda que le permite ir directamente a un
título/capítulo/pista/tiempo especificado.
●
Modo VCR
Presione para realizar una Búsqueda de tiempo o
Búsqueda de índice.
Precaución: No toque los pasadores interiores de las tomas
en el panel trasero. La descarga electroestática puede dañar
permanentemente el DVD/VCR.
DVD/VCR VCR
AUDIO OUT AUDIO IN
VIDEO OUT VIDEO IN
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
DVD
Y
C
B
PB
CR
PR
L
R
L
ANT-IN
ANT-OUT
R
L
R
DIGITAL
AUDIO OUT
COAXIAL
I P
PROGRESSIVE
12
11
10
89
7
6
21 3 45
VISIÓN TRASERA
Nota
¡La toma S-VIDEO OUT, toma COAXIAL, y tomas COMPONENT VIDEO OUT son sólo útiles en el modo
DVD.
1. Toma ANT-IN (Entrada de antena)
Conecte su antena, caja de cable o sistema de radiodifusión
directa.
2. Tomas DVD/VCR AUDIO OUT
Conecte aquí los cables de audio provistos y a las tomas de
entrada de audio de un televisor u otro equipo de audio.
3. Tomas AUDIO IN
Conecte aquí los cables de audio procedentes de las tomas
de salida de audio de un camcorder, otra videograbadora o
una fuente de audio.
4. Cable de alimentación de CA
Conecte a una toma de corriente CA estándar para
suministrar corriente al DVD/VCR.
5. Tomas COMPONENT VIDEO OUT (sólo DVD)
Conecte aquí los cables de videó componente opcionales y a
las tomas de entrada de Videó componente de un televisor.
6. Toma COAXIAL (sólo DVD)
Conecte aquí un cable de audio digital coaxial opcional y a
la toma de entrada Audio Digital Coaxial de un
decodificador o receptor de audio.
7. Tomas DVD AUDIO OUT (sólo DVD)
Conecte aquí los cables de audio provistos y a las tomas de entrada
de audio de un televisor u otro equipo de audio (sólo DVD).
8. Toma S-VIDEO OUT (sólo DVD)
Conecte aquí un cable de S-Video opcional y a la toma de
entrada de S-Video de un televisor.
9. INTERLACE/PROGRESSIVE SCAN SELECTOR
para seleccionar la exploración interenlazada o progresiva.
10. Toma VIDEO IN (sólo VCR)
Conecte un cable procedente de la toma de salida de video
de un camcorder, otra videograbadora o una fuente de
audio-visual (reproductor de disco láser, reproductor de
disco de video, etc.) aquí.
11. Toma DVD/VCR VIDEO OUT
Conecte aquí el cable de video amarillo (provisto) y a la
toma de entrada de video de TV.
Si selecciona P (PROGRESSIVE) en INTERLACE/
PROGRESSIVE SCAN SELECTOR, no sale la señal de
video DVD a su TV.
12. Toma ANT-OUT (salida de antena)
Utilice el cable coaxial RF provisto para conectar esta toma
a la toma ANTENNA IN en su TV.
H9451UD(EN).qx33 03.1.22 7:22 PM Page 38
Español
–
39
–
SP
1L25
CAMBIO DE VCR/DVD
Como este producto utiliza videograbadoras y reproductores DVD, es necesario seleccionar el modo de
salida correcto.
DVD OUTPUT VCR
+10
EJECT
3
MODE
2
SEARCH
OPEN/CLOSE
9
ZOOM
DISPLAY
8
AUDIO
0
TOP MENU
SETUP
PLAY
SKIP
CH
CH
56
1
A-B REPEAT
REPEAT
7
CLEAR/C. RESET
SUBTITLE/TIMER
MODE
ANGLE
DVD VCR/TV
DISC
NAVIGATION
VCR
SLOW SPEED REC
RETURN
MENU
STOP
TV POWER
VIDEO/TV
4
SURROUND
PAUSE/STEP
VOL
TV
ENTER
Botón OUTPUT
Luz DVD OUTPUT
Luz VCR OUTPUT
Botón DVD
Botón VCR
POWER/STANDBY
CHANNEL
PLAYSTOP/EJECT
VIDEO IN
F.FWDREWREC/OTR
TIMER REC
DVD OUTPUT VCRSTOP PLAY
OPEN/CLOSE
L
(mono)
AUDIO IN R
LINE 2
Presione el VCR en el control remoto.
(Verifique que la luz VCR OUTPUT está encendida.)
CAMBIO AL MODO VCR
Notas
¡Presionando sólo el OUTPUT en el panel delantero no cambia el modo del control remoto. Usted siempre
necesita seleccionar el modo correcto en el control remoto, también.
Presione el DVD en el control remoto.
(Verifique que la luz DVD OUTPUT está encendida.)
CAMBIO AL MODO DVD
H9451UD(EN).qx33 03.1.22 7:22 PM Page 39
–
40
–
SP
1L25
CONEXION A UN SISTEMA DE AUDIO
DVD/VCR A CONEXION DE TV
1. Desconecte el cable de alimentación CA de la toma de
corriente CA.
2. Desconecte la antena o cable del TV.
3. Conecte la antena o cable a la toma ANT-IN del
DVD/VCR.
4. Conecte el DVD/VCR al TV utilizando el cable RF.
5. Enchufe los cables de alimentación CA del DVD/VCR
y TV dentro de las tomas de corriente CA.
Si su TV no tiene terminales A/V:
1. Conecte el DVD/VCR al TV utilizando un cable
RF (vea DVD/VCR A CONEXION DE TV).
2. Seleccione el canal 3 en su TV.
3. Presione PLAY.
¡Si aparece ruido, cambie el canal de salida RF de la
videograbadora al canal 4 presionando PLAY
durante 3 segundos durante la reproducción.
¡
Hay casos en los que el canal de salida RF no cambia
según la situación (Por ejemplo cuando ajusta el
seguimiento utilizando CHANNEL ( ).
¡En este caso, detenga la reproducíon y comience
nuevamente la reproducción. Luego presione PLAY
en la videograbadora durante 3 segundos.
¡Si hay un corte eléctrico o se desechufa el
DVD/VCR durante más de 30 segundos, el canal de
salida RF vuelve al canal 3.
(
)
CANAL DE SALIDA RF
CONEXIONES
Por favor, vea la página 14 para detalles.
CONEXION A UN TV (PARA VIDEO)
Por favor vea la página 15 para detalles.
PREPARACION DE UN CANAL AUTOMATICO
PREPARACIÓN
1 Es necesario conectar primero la antena o
cable a la videograbadora. Luego conecte el
enchufe eléctrico de DVD/VCR a una toma
de corriente CA.
2 Encienda el TV y ponga el TV en el canal 3.
¡Si aparece ruido, cambie el canal de salida RF de la
videograbadora al canal 4 presionando PLAY
durante 3 segundos durante la reproducción. Luego
seleccione el mismo canal (4) en su TV. (Vea el
“Canal de salida RF” en la página 40 Para más
detalles.)
3 Encienda la videograbadora presionando
yy
/I. Se encenderá la luz POWER.
4 Seleccione el idioma en la pantalla
(“INGLES”, “FRANCÉS” o ESPAÑOL”)
presionando
K o L. Luego presione B.
5 Comience el preajuste de canal presionando
B una vez. El sintonizador explora y
memoriza todos los canales activos en su
área.
¡La videocámara distingue entre los canales de TV
normales y los canales de cable.
6 Después de explorar, el sintonizador se
detiene en el canal memorizado más bajo. La
pantalla de TV retorna al modo TV.
¡Si aparece otra vez “AUTO SET UP” en la pantalla
de TV, inspeccione las conexiones de cable.
Presione nuevamente B y la videograbadora volverá
a hacer el preajuste.
VCR
H9451UD(EN).qx33 03.1.22 7:22 PM Page 40
Español
–
41
–
SP
1L25
PREPARACION DE RELOJ
1 Seleccione el menú principal presionando
MENU.
¡
Si el reloj no está ajustado, aparece priemero el
menú CLOCK SET. En este caso, siga el paso (3).
2 Seleccione “CLOCK SET” presionando K o
L. Luego presione B.
3 Ajuste el reloj.
¡Para retroceder un paso, presione {.
4 Ponga en marcha el reloj presionando
CLEAR/C.RESET o
B.
VCR
AJUSTE DE RELOJ
MES DIA AÑO
03 / 17 LUN 2003
HORA MINUTO AM/PM
05 : 40 PM AM
PM
1) Ajuste el mes
Presione o o p repetidamente.
Luego presione B.
2) Ajuste el día
Presione o o p repetidamente.
Luego presione B.
3) Ajuste el año
Presione o o p repetidamente.
Luego presione B.
El día de la semana aparecerá automáticamente.
4) Ajuste la hora
Presione o o p repetidamente.
Luego presione B.
5) Ajuste el minuto
Presione o o p repetidamente.
Luego presione B.
6) Ajuste el AM o PM
Presione o o prepetidamente.
REPRODUCCIÓN BÁSICA
Para empezar
¡Conecte la alimentación del TV, amplificador y
cualquier otro componente que se encuentre
conectado al DVD/VCR.
¡Asegúrese que el TV y el receptor de audio (de venta
en los comercios) están en el canal correcto.
¡Seleccione el modo DVD presionando DVD en el
control remoto o la salida en el panel delantero.
1 Presione
yy
/I.
¡Aparecerá “Load” breVD/VCR.
–
42
–
EN
1L25
Hitachi has made every effort to assure you hours of trouble free operation from your unit . However , should you require
service , a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico . Each
facility will provide you with convenient and expedient assistance . Our service "Hot line" operator will direct you to the
Hitachi Authorized Service Facility nearest you . Just present proof of purchase and/or delivery receipts to the Hitachi
Authorized Service Facility and service will be rendered in accordance with the terms of the limited warranty as stated
on your warranty card or operating guide .
Should you have any questions regarding in-warranty service, operation or technical assistance, please contact:
HITACHI AMERICA, LTD.
HOME ELECTRONICS DIVISION
1855 Dornoch Court,
San Diego, California 92154-7255,
Tel: 1-800-HITACHI
(1-800-448-2244)
HITACHI CANADA LTD .
DIGITAL MEDIA DIVISION
6740 Campobello Road, Mississauga,
Ontario L5N 2L8 CANADA
Tel: 1-800-HITACHI
(1-800-448-2244)
during the business hours
Monday - Friday EST 9:00am~7:00pm
Saturday EST 9:00am~5:00pm
durant les heures de hureau:
Lundi au Vedredi 9:00am~7:00pm (h.n.e.)
Samedi 9:00am~5:00pm (h.n.e.)
DECLARA
TION OF CONFORMITY
with FCC Rules for Electromagnetic Compatibility
Products: DVD PLAYER with VIDEO
CASSETTE RECORDER
Models: DV-PF73U
Trade Name: HITACHI
This device complies with part 15 of FCC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party: HITACHI AMERICA, LTD.
HOME ELECTRONICS DIVISION
1855 Dornoch Court, San Diego,
CA 92154-7255 U.S.A
Tel:619-661-0227
H9451UD(EN).qx33 03.1.22 7:22 PM Page 42
–
43
–
EN
1L25
WARRANTY
✄
NOT FINAL
H9451UD(EN).qx33 03.1.22 7:22 PM Page 43
0VMN03465
H9451UD
★★★★★
TJ16681 C Hitachi, Ltd. 2003
Printed in China
✄
WARRANTY
NOT FINAL
H9451UD(EN).qx33 03.1.22 7:22 PM Page 44
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Hitachi DVD VCR Combo DVPF73U Manual de usuario
- Categoría
- Reproductores de DVD
- Tipo
- Manual de usuario
- Este manual también es adecuado para
en otros idiomas
Artículos relacionados
Otros documentos
-
Polaroid DVC-2000 Manual de usuario
-
Denver MT-779DVBT El manual del propietario
-
Denon DVM-1805 Manual de usuario
-
Memorex MVD4540B Manual de usuario
-
Disney DP7000 Manual de usuario
-
Sears DVD VCR Combo SRD2900 Manual de usuario
-
Disney Cars C1320PTVD Manual de usuario
-
Philips DVD VCR Combo DVP3345VB/F7 Manual de usuario
-
Sanyo VWM950 Manual de usuario
-
Sylvania 6513DD Manual de usuario