Titan PowrLiner 5000 El manual del propietario

Marca: Titan

Modelo: PowrLiner 5000

Categoría: Rociador de pintura

Tipo: El manual del propietario

Este manual también es adecuado para

PowrLiner™ 5000

Printed in the U. S. A.

Do not use this equipment before reading this manual!

PowrLiner 5000

Owner’s Manual

For professional use only

NOTE: This manual contains important warnings

and instructions. Please read and retain

for reference.

Model Numbers:

759-500 1 Gun

759-501 2 Gun

Table of Contents

Introduction ................................................................................2

Safety Precautions.....................................................................2

Grounding Instructions..............................................................4

Gasoline Engine Safety ............................................................4

Español ...................................................................................11

Français ..................................................................................13

Setup ...........................................................................................5

Fueling.........................................................................................5

Startup.........................................................................................6

Cleanup .......................................................................................6

Pressure Relief Procedure .......................................................6

Maintenance................................................................................7

Airless Tip Selection..................................................................8

Troubleshooting ...................................................................8–10

Airless Gun ...............................................................................8

Spray Patterns..........................................................................9

Hydraulic Motors.....................................................................10

Fluid Pumps............................................................................10

Parts Lists and Service Instructions................................15–29

Main Assembly — Gas Models ..............................................15

Power Convertokits...........................................................16–17

Cart Assembly.........................................................................18

Belt Guard Assembly ..............................................................18

Hydraulic System....................................................................19

Hydraulic Motor.................................................................20–22

Fluid Pump........................................................................22–23

Inlet Accessories.....................................................................24

Outlet Accessories..................................................................25

Second Gun Assembly Complete.....................................26–27

Trigger Assembly ....................................................................28

Line Pointer.............................................................................28

SAE O-Ring Fitting Installation...............................................29

Accessories and Service Kits.................................................29

Athletic Field Marking Kit/Turf Kit ...........................................29

Warranty ....................................................................................32

Introduction

Congratulations on having selected the finest airless sprayer

available in the world. Speeflo piston pumps are tireless

workhorses — so tough they are virtually indestructible, even

under the most severe service. Speeflo designs and builds

equipment with superior quality and reliability. Equipment that

will last for years with minimal maintenance and downtime. This

equipment will make you money year after year. We thank you

for your purchase and welcome you to our large and growing

family of Speeflo users.

The unique ability of this PowrLiner to operate with either gas or

electric power provides you with the flexibility to work indoors or

outside where no electricity is available.

Hydraulic drive makes possible the longest stroke and slowest

cycling pumps in the industry, which translates into low

maintenance and longer life. Electric units operate quietly with

no motor starting and stopping.

This PowrLiner is equipped with Speeflo's exclusive and

patented Severe Service 500™ fluid pump. This technology will

give you significantly longer rod, cylinder, and packing life than

any other sprayer built in the world. This double ball piston

pump employs a dependable and durable time-tested design. All

pumps use an exclusive thick hard chrome plating on rod and

cylinder parts. This patented plating process is harder than

nitralloy, stainless steel, or hard chrome used by any other paint

pump manufacturer and much more abrasion resistant. Highly

polished parts reduce friction, extend packing life, and avoid

damage from corrosion and abrasion. More than 100,000 of

these pumps are in operation around the world.

PowrLiner offers other cost saving features:

• Freeze-proof pressure control

• Choice of power — gas, electric, or both

• Tungsten carbide valve seats

• Self-adjusting packings

• Exclusive hand-tight swivel foot valve

• Large capacity inline paint filter

• Waterborne compatible

• "Floating Ball" pressure bleed valve

• 5 gallon siphon hose and bleed line assemblies are standard

You have made an excellent choice. We know you will be

pleased with your new PowrLiner. Thanks again for selecting

Speeflo. We appreciate your business.

Safety Precautions

This manual contains information that must be read and

understood before using the equipment. When you come to an

area that has one of the following symbols, pay particular

attention and make certain to heed the safeguard.

This symbol indicates a potential hazard that may cause

serious injury or loss of life. Important safety information

will follow.

This symbol indicates a potential hazard to you or to the

equipment. Important information that tells how to prevent

damage to the equipment or how to avoid causes of minor

injuries will follow.

HAZARD: Injection injury - A high pressure stream

produced by this equipment can pierce the skin

and underlying tissues, leading to serious injury

and possible amputation. See a physician

immediately.

DO NOT TREAT AN INJECTION INJURY AS A SIMPLE CUT!

Injection can lead to amputation. See a physician

immediately.

The maximum operating range of the unit is 3300 PSI /

228BAR fluid pressure.

PREVENTION:

• NEVER aim the gun at any part of the body.

• NEVER allow any part of the body to touch the fluid stream.

DO NOT allow body to touch a leak in the fluid hose.

• NEVER put your hand in front of the gun. Gloves will not

provide protection against an injection injury.

• ALWAYS lock the gun trigger, shut the pump off, and release all

pressure before servicing, cleaning the tip or guard, changing

tip, or leaving unattended. Pressure will not be released by

turning off the motor. The PRIME/SPRAY knob must be turned

to PRIME to relieve the pressure. Refer to the PRESSURE

RELIEF PRESSURE described in the pump manual.

WARNING

NOTE: Notes give important information that should

be given special attention.

CAUTION

WARNING

• ALWAYS keep the tip guard in place while spraying. The tip

guard provides some protection but is mainly a warning

device.

• ALWAYS remove the spray tip before flushing or cleaning

the system.

• The paint hose can develop leaks from wear, kinking and

abuse. A leak can inject material into the skin. Inspect the

hose before each use.

• NEVER use a spray gun without a trigger lock and trigger

guard in place and in good working order.

• All accessories must be rated at or above 3300 PSI / 228

BAR. This includes spray tips, guns, extensions, and hose.

HAZARD: EXPLOSION OR FIRE - Solvent and paint fumes

can explode or ignite. Severe injury and/or

property damage can occur.

PREVENTION:

• Provide extensive exhaust and fresh air introduction to keep

the air within the spray area free from accumulation of

flammable vapors.

• Avoid all ignition sources such as static electric sparks, open

flames, pilot lights, and hot objects. Connecting or

disconnecting power cords or working light switches can

make sparks.

• Do not smoke in spray area.

• Fire extinguisher must be present and in good working

order.

• Place paint pump in a well ventilated area. Flammable

vapors are often heavier than air. Floor area must be

extremely well ventilated. The paint pump contains arcing

parts that emit spark and can ignite vapors.

• The equipment and objects in and around the spray area

must be properly grounded to prevent static sparks.

• Use only conductive or grounded high pressure fluid hose.

Gun must be grounded through hose connections.

• Power cord must be connected to a grounded circuit

(electric models only).

• Always flush unit into a separate metal container, at low

pump pressure, with spray tip removed. Hold gun firmly

against side of container to ground container and prevent

static sparks.

• Follow the material and solvent manufacturer's warnings and

instructions.

• Use extreme caution when using materials with a flashpoint

below 70° F (21° C). Flashpoint is the temperature that a

fluid can produce enough vapors to ignite.

• Plastic can cause static sparks. Never hang plastic to

enclose a spray area. Do not use plastic drop cloths when

spraying flammable materials.

• Use lowest possible pressure to flush equipment.

GAS ENGINE (WHERE APPLICABLE)

Always place pump outside of structure in fresh air. Keep all

solvents away from the engine exhaust. Never fill fuel tank with

a running or hot engine. Hot surface can ignite spilled fuel.

Always attach ground wire from pump unit to a grounded object,

such as a metal water pipe. Refer to engine owner’s manual for

complete safety information.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury. It is

important to treat the injury as soon as possible. DO

NOT delay treatment to research toxicity. Toxicity is a

concern with some coatings injected directly into the

blood stream. Consultation with a plastic surgeon or

reconstructive hand surgeon may be advisable.

HAZARD: EXPLOSION HAZARD DUE TO INCOMPATIBLE

MATERIALS - Will cause severe injury or property

damage.

PREVENTION:

• Do not use materials containing bleach or chlorine.

• Do not use halogenated hydrocarbon solvents such as

mildewcide, methylene chloride and 1,1,1 - trichloroethane.

They are not compatible with aluminum.

• Contact your coating supplier about the compatibility of

material with aluminum.

HAZARD: HAZARDOUS VAPORS - Paints, solvents,

insecticides, and other materials can be harmful

if inhaled or come in contact with the body.

Vapors can cause severe nausea, fainting, or

poisoning.

PREVENTION:

• Use a respirator or mask if vapors can be inhaled. Read all

instructions supplied with the mask to be sure it will provide

the necessary protection.

• Wear protective eyewear.

• Wear protective clothing as required by coating

manufacturer.

HAZARD: GENERAL - This product can cause severe injury

or property damage.

PREVENTION:

• Read all instructions and safety precautions before operating

equipment.

• Always disconnect the motor from the power supply before

working on the equipment (electric models only).

• Follow all appropriate local, state, and national codes

governing ventilation, fire prevention, and operation.

• The United States Government Safety Standards have been

adopted under the Occupational Safety and Health Act

(OSHA). These standards, particularly part 1910 of the

General Standards and part 1926 of the Construction

Standards should be consulted.

• Use only manufacturer authorized parts. User assumes all

risks and liabilities when using parts that do not meet the

minimum specifications and safety devices of the pump

manufacturer.

• Before each use, check all hoses for cuts, leaks, abrasion

or bulging of cover. Check for damage or movement of

couplings. Immediately replace the hose if any of these

conditions exist. Never repair a paint hose. Replace it with

another grounded high-pressure hose.

• All hoses, swivels, guns, and accessories must be pressure

rated at or above 3300PSI/228 BAR.

• Do not spray outdoors on windy days.

• Wear clothing to keep paint off skin and hair.

Grounding Instructions

Electric models must be grounded. In the event of an electrical

short circuit, grounding reduces the risk of electric shock by

providing an escape wire for the electric current. This product is

equipped with a cord having a grounding wire with an appropriate

grounding plug. The plug must be plugged into an outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

DANGER — Improper installation of the grounding plug can

result in a risk of electric shock. If repair or replacement of the

cord or plug is necessary, do not connect the green grounding

wire to either flat blade terminal. The wire with insulation having a

green outer surface with or without yellow stripes is the

grounding wire and must be connected to the grounding pin.

Check with a qualified electrician or serviceman if the grounding

instructions are not completely understood, or if you are in doubt

as to whether the product is properly grounded. Do not modify

the plug provided. If the plug will not fit the outlet, have the

proper outlet installed by a qualified electrician.

This product is rated more than 15 amperes and is for use on a

circuit having a nominal rating of 120 volts, or the product is for

use on a circuit having a nominal rating more than 120 volts, and

is factory-equipped with a specific electric cord and plug to permit

connection to a proper electric circuit. Make sure that the

product is connected to an outlet having the same configuration

as the plug. No adapter should be used with this product. If the

product must be reconnected for use on a different type of

electric circuit, the reconnection should be made by qualified

service personnel.

Use only a 3-wire extension cord that has a 3-blade

grounding plug and a 3-slot receptacle that will accept the

plug on the product. Make sure your extension cord is in

good condition. When using an extension cord, be sure to

use one heavy enough to carry the current your product will

draw. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. For lengths less

than 50 feet, No. 12 AWG extension cords should be used. If

an extension cord is to be used outdoors, it must be marked

with the suffix W-A after the cord type designation. For

example, a designation of SJTW-A would indicate that the

cord would be appropriate for outdoor use.

CAUTION

Gasoline Engine Safety

The engine exhaust from this unit contains chemicals

known to the State of California to cause cancer, birth

defects, or other reproductive harm.

1. Gasoline engines are designed to give safe and dependable

service if operated according to instructions. Read and

understand the engine manufacturer’s Owner's Manual

before operating the engine. Failure to do so could result in

personal injury or equipment damage.

2. To prevent fire hazards and to provide adequate ventilation,

keep the engine at least 1 meter (3 feet) away from

buildings and other equipment during operation. Do not

place flammable objects close to the engine.

3. Children and pets must be kept away from the area of

operation due to a possibility of burns from hot engine

components or injury from any equipment the engine may

be used to operate.

4. Know how to stop the engine quickly, and understand the

operation of all controls. Never permit anyone to operate

the engine without proper instructions.

5. Gasoline is extremely flammable and is explosive under

certain conditions.

6. Refuel in a well-ventilated area with the engine stopped. Do

not smoke or allow flames or sparks in the refueling area or

where gasoline is stored.

7. Do not overfill the fuel tank. After refueling, make sure the

tank cap is closed properly and securely.

8. Be careful not to spill fuel when refueling. Fuel vapor or

spilled fuel may ignite. If any fuel is spilled, make sure the

area is dry before starting the engine.

9. Never run the engine in an enclosed or confined area.

Exhaust contains poisonous carbon monoxide gas;

exposure may cause loss of consciousness and may lead to

death.

10. The muffler becomes very hot during operation and remains

hot for a while after stopping the engine. Be careful not to

touch the muffler while it is hot. To avoid severe burns or

fire hazards, let the engine cool before transporting it or

storing it indoors.

11. Never ship/transport unit with gasoline in the tank.

DO NOT use this equipment to spray water or acid.

Do not lift by cart handle when loading or unloading.

CAUTION

WARNING

Set Up

Read, understand, and follow all warnings before starting

or operating this sprayer.

Required tools: Crescent Wrench

1. One Gun Operation — Attach the gun and hose. Always

use a spray hose at least 50 feet long. Do not use PTFE

or thread sealant on this assembly. Do not install the spray

tip at this time.

2. Two Gun Operation — Remove the plug from the second

gun outlet. Connect a hose and a gun to the outlet.

3. Fill the Wet-Cup 1/2 full with Speeflo Piston Lube (P/N

700-925) supplied by the factory. This extends packing

life.

4. Electric Models — Use a 20 amp service outlet. Always

locate the AC electric model within 10 to 15 feet of the

service outlet. Any extension cord will create some voltage

drop. For both AC and DC models, if an extension cord is

necessary, use only grounded 3 wire # 12 wire.

If the unit is being operated in an area that is overloaded

by other appliances or low voltage conditions, it is

important to start the unit "unloaded." Tip the electric

motor forward so that the belt is loosened and the motor

starts without full load. This reduces the amperage draw

on starting and may avoid kicking out the circuit breaker.

5. Be sure the PowrLiner system is grounded. All Speeflo

units are equipped with a grounding lug. A grounding

cable (not supplied) should be used to connect the unit to a

true earth ground. Check your local electrical regulations

for detailed grounding instructions. See the “Accessories

and Service Kits” section for ordering information.

6. Strain all paints with Speeflo 5 gallon Nylon Strainer (P/N

160-524) or Speeflo 1 gallon Nylon Strainer (P/N 160-124)

to assure trouble-free operation and freedom from frequent

cleaning of inlet screen and gun strainer.

Proper grounding is important. This applies to both gas

and electric powered models. The passage of some

materials through the nylon fluid hose will build up a static

electric charge, which if discharged, could ignite solvent

vapors present and create an explosion.

Fueling

Gasoline is extremely flammable and is explosive under

certain conditions.

• ALWAYS turn the engine off before refueling.

• Refuel in a well-ventilated area.

• Do not smoke or allow flames or sparks in the refueling

area or where gasoline is stored.

• Do not overfill the fuel tank. After refueling, make sure the

tank cap is closed properly and securely.

• Be careful not to spill fuel when refueling. Spilled fuel or

fuel vapor may ignite. If any fuel is spilled, make sure the

area is dry before starting the engine.

• Avoid repeated or prolonged contact with skin or breathing

of vapor.

• Keep out of the reach of children.

Specifications

• Use automotive gasoline that has a pump octane number

of 86 or higher, or that has a research octane number of 91

or higher.

• Unleaded fuel produces fewer engine and spark plug

deposits and extends the life of exhaust system

components.

• Never use stale or contaminated gasoline or an oil/gasoline

mixture. Avoid getting dirt, dust or water in the fuel tank.

Use of a lower octane gasoline can cause persistent

"pinging" or heavy "spark knock" (a metallic rapping noise)

which, if severe, can lead to engine damage.

Gasolines Containing Alcohol

If you decide to use a gasoline containing alcohol (gasohol), be

sure its octane rating is at least as high as that recommended

by the engine manufacturer. There are two types of "gasohol":

one containing ethanol, and the other containing methanol. Do

not use gasohol that contains more than 10% ethanol. Do not

use gasoline containing methanol (methyl or wood alcohol) that

does not also contain co-solvents and corrosion inhibitors for

methanol. Never use gasoline containing more than 5%

methanol, even if it has co-solvents and corrosion inhibitors.

NOTE: Fuel system damage or engine performance

problems resulting from the use of fuels that

contain alcohol is not covered under the

warranty. The engine manufacturer cannot

endorse the use of fuels containing methanol

since evidence of their suitability is incomplete at

this time.

Before buying gasoline from an unfamiliar station,

try to find out if the gasoline contains alcohol. If

it does, confirm the type and percentage of

alcohol used. If you notice any undesirable

operating characteristics while using a gasoline

that contains alcohol, or one that you think

contains alcohol, switch to a gasoline that you

know does not contain alcohol.

NOTE: If "spark knock" or "pinging" occurs at a steady

engine speed under normal load, change brands

of gasoline. If spark knock or pinging persists,

consult your authorized Honda dealer. Failure

to do so is considered misuse, and damage

caused by misuse is not covered by Honda's

Limited Warranty.

Occasionally you may experience light spark

knock while operating under heavy loads. This

is no cause for concern, it simply means your

engine is operating efficiently.

WARNING

Startup

1. Areas must be well ventilated to prevent hazardous

operation with volatile solvents or exhaust fumes.

2. Before starting the unit. check oil levels.

a. The hydraulic fluid level should read "Full" on the dipstick.

CHECK IT REGULARLY. See “Hydraulic System” in the

Maintenance section of this manual for changing or adding

hydraulic fluid. Do not overfill. Use only Speeflo Coolflo™

Hydraulic Fluid (P/N 430-361).

b. The gasoline engine oil level is determined by the

manufacturer. Check the engine manufacturer's service

manual (supplied).

Use of Speeflo's Coolflo™ Hydraulic Fluid is mandatory in

the PowrLiner hydraulic system. Do not use any other

hydraulic fluid. Use of any other hydraulic fluid may

seriously damage hydraulic system and will void warranty.

3. Open the orange-handled hydraulic

shut-off valve located on the

hydraulic pressure hose. Handle

should be in line with hose. The

figure below shows the handle in

the open position.

4. Turn the pressure control knob

counterclockwise (as viewed from

top) to its lowest pressure setting.

5. Open the pressure bleed valve by

turning it counterclockwise. This

relieves pressure.

a. Your new sprayer was tested at the factory with mineral

spirits. You must clean the system before spraying to

avoid contamination of the sprayed material.

If you are spraying a water based latex, flush with warm,

soapy water followed by a clean water rinse. If you are

using any other coating, flush with warm, soapy water

followed by a solvent. Check with the material

manufacturer for a compatible solvent. Place syphon

tube assembly into proper solvent or water.

b. Place waste container below bleed line.

c. Start engine or electric motor. Turn the pressure control

knob clockwise (increasing pressure) until pump cycles

evenly and solvent flows freely from bleed line.

d. Close the pressure bleed valve by turning it clockwise.

This allows the system to pressurize. Hold the gun

trigger open, without spray tip attached, until the fluid

flows smoothly.

6. Repeat above starting procedure with paint material. Lock

gun trigger and attach spray tip. Refer to the spray gun’s

Technical Data Sheet or Owner's Manual for tip installation

and selection of the proper tip size.

7. Test spray pattern. Operate the pump at the lowest hydraulic

pressure that provides good atomization. See the the

Troubleshooting section in this manual if you are not getting

the proper pattern.

8. Operating pressure is adjustable from 400 to 3300 psi (28

to 228 BAR) by turning the pressure control knob

clockwise. Do not turn the knob clockwise more than

necessary to provide satisfactory atomization. Excess

pressure wears out spray tips.

9. When restarting the unit, reduce the pressure at the

pressure control knob and the pressure bleed valve.

Cleanup

Special cleanup instructions for use with flammable

solvents:

• Always flush spray gun preferably outside.

• If collecting flushed solvents in a one gallon metal

container, place it into an empty five gallon metal container,

then flush solvents.

• Area must be free of flammable vapors.

• Follow all cleanup instructions.

Pressure Relief Procedure

Always reduce pressure when you are cleaning a clogged

tip, changing a tip, servicing any part of the system, or

shutting down. Follow the steps below:

1. Engage the gun trigger lock.

2. Shut off the power source.

3. Close the orange-handled hydraulic shut-off valve on the

hydraulic pressure hose.

4. Open the pressure bleed valve by turning it

counterclockwise at least three full turns.

5. Disengage the gun trigger lock and hold trigger open until

flow of material stops.

6. Be certain to hold a metal part of the gun firmly to the side

of a grounded metal container.

Cleaning a Clogged Tip

1. Follow the “Pressure Relief Procedure” above.

2. If tip clogs, rotate tip handle 180° until arrow on handle is

facing the opposite of spray direction and clicks in reverse

position.

3. Trigger gun once so that the pressure can blow the clog

out. NEVER use the tip in the reverse position for more

than ONE trigger pull at a time. This procedure can be

repeated until the tip is free of clogging.

The flow from the spray tip is at very high pressure. Contact

with any body part may be dangerous. Do not place finger

on gun outlet. Do not point the gun at any person. Never

operate the spray gun without the proper tip guard.

Color Change/Clean Out

Use only compatible solvents when cleaning out oil based

enamels, lacquers, coal tar, and epoxies. Check with the

fluid manufacturer for the recommended solvent.

1. Reduce pressure by turning the pressure control knob and the

pressure bleed valve counterclockwise. Follow the “Pressure

Relief Procedure” above. The pressure bleed valve should be

turned counterclockwise at least three full turns.

2. Pull siphon tube out of material container.

3. Remove spray tip from gun. Hold the gun trigger open until

material flow stops.

4. Put the siphon tube into wash solvent or water as

applicable, and operate pump slowly at low pressure until

solvent flows freely from the bleed line.

Pressure

Bleed

Valve

WARNING

Pressure

Bleed

Valve

Hydraulic

Shut-Off

Valve

CAUTION

5. Close the pressure bleed valve and hold gun trigger open

until solvent flows freely from gun. If solvent is not too

dirty, recirculate it by flowing gun stream back into solvent

container. Use additional clean solvent and repeat

procedure if necessary.

6. Check gun strainer screen and pump outlet filter screen

daily. Use 50 mesh screens with spray tip size .015 and

larger. Use 100 mesh screens with spray tip sizes .013 and

smaller.

7. Replace paint filter cap to maximum clockwise rotation. The

filter cover should be hand removable after the first or

second use with new PTFE o-ring.

IMPORTANT: O-ring must have PTFE backup washer

to seal properly.

8. If unit has been spraying a water soluble material, flush

with water and then repeat procedure with mineral spirits or

Varsol solvent.

9. Wash spray tip in solvent. Blow tip clean with air pressure

directed through the tip in the reverse direction.

Maintenance

Hydraulic System

Use of Speeflo's Coolflo™ Hydraulic Fluid is mandatory in

the hydraulic system. Do not use any other hydraulic fluid.

Use of any other hydraulic fluid may seriously damage the

hydraulic system and will void warranty.

1. Check the hydraulic fluid daily. It should read "Full" on the

dipstick. If it is low, add only Speeflo Coolflo™ Hydraulic

Fluid (P/N 430-361). Never add or change hydraulic fluid

except in a clean dust free area. Contamination of the

hydraulic fluid will shorten hydraulic pump life and may void

warranty.

2. Change the hydraulic fluid every twelve months. Drain old

fluid from tank and fill with 5 quarts of Speeflo Coolflo™

Hydraulic Fluid. Start operation of the system at just

enough pressure to operate the fluid pump. Run the

system at this low pressure for at least 5 minutes. This

removes air from the system. Check the fluid level after

this procedure.

3. The hydraulic system has an external replaceable hydraulic

filter. Change the filter every twelve months.

4. The hydraulic pump should not be serviced in the field. If

service on the hydraulic pump is required, it must be

returned to Speeflo.

General Fluid Pump Maintenance

If the paint pump is going to be out of service for an extended

period of time, it is recommended that following cleanup a

kerosene and oil mixture be introduced as a preservative.

Packings may tend to dry out from lack of use. This is

particularly true of the upper packing set, for which upper

packing lubricant “Piston Lube” (P/N 700-925) is recommended

in normal usage.

If the paint pump has been out of service for an extended

period of time, it may be necessary to prime the suction by

pouring some of the paint solvent into the inlet siphon tube to

restart. It is extremely important that the threads on the inlet

siphon hose coupling are properly sealed. Any air leakage will

produce erratic operation of pump and may damage the

system. The up and the down strokes should be approximately

equal in time. That is, one should not be faster than the other.

A fast up or down stroke may indicate air in the system or

malfunctioning valve or seats. See the Troubleshooting section.

Hydraulic Motor and Fluid Pump

Service

See the Parts List and Service Instructions section of this

manual for maintenance and service instructions on the

reciprocating hydraulic motor and the fluid pump.

Basic Engine Maintenance

• For detailed engine maintenance and technical

specifications refer to the separate engine manual.

• All service to the engine should be performed by an

authorized Honda Power Equipment dealer. To locate a

dealer in your area, look in the Yellow Pages of your

telephone directory under Gasoline Engines, Garden &

Lawn Equipment & Supplies, Lawnmowers, etc.

• The Honda engine is warranted exclusively by American

Honda Motor Co., Inc.

• Use a premium quality motor oil certified to meet or exceed

U.S. Automotive requirement SG.SF/CC.CD. SAE 10W30

is recommended for general all temperature use. Other

viscosities may be required in other climates.

• Use only a (NGK) BP6ES or BPR6E spark plug. Gap the

plug to 0.028 to 0.031 In. (0.7 to 0.8 mm) Always use a

spark plug wrench.

DAILY: Check engine oil level. Fill as necessary. Check

gasoline level. Fill as necessary.

Always follow the fueling procedure outlined earlier in this

manual.

FIRST 20 HOURS: Change engine oil.

EVERY 100 HOURS: Change engine oil.

WEEKLY: Remove the air filter cover and clean the element. In

very dusty environments, check the filter daily. Replace the

element as needed. Replacement elements can be purchased

from your local Honda dealer.

Engine Operation and Service

1. Clean and oil air filter pad on gasoline engine every 25

hours or once weekly. Do not permit the air intake screen

around the fly wheel of the gas engine to load up with paint

or trash. Clean it regularly. The service life and efficiency of

the gas engine model depends upon keeping the gasoline

engine running properly. Change the oil in the engine every

100 hours. Failure to observe this may result in engine

overheating. Consult the engine manufacturer's service

manual provided.

2. To conserve fuel, service life, and efficiency of the unit

always operate the gasoline engine at the lowest RPM at

which it runs smoothly without laboring and delivers the

amount required for the particular painting operation.

Higher RPM does not produce higher working pressure.

The gasoline engine is connected to the hydraulic pump by

a pulley combination designed to produce full paint delivery

of 2.0 GPM at 3600 RPM.

3. The warranty on gasoline engines or electric motors is

limited to the original manufacturer.

If electric motor overloads and stops running,

IMMEDIATELY turn the motor off and follow the Pressure

Relief Procedure outlined earlier in this manual. Wait until

the motor cools (approximately 30 minutes). Then push in

the bubble top, manual reset button, turn the motor on and

pressurize the system.

For CSA approved units only:

The ON / OFF switch is also the RESET!

WARNING

CAUTION

Airless Tip Selection

Tips are selected by the orifice size and fan width. The proper selection is determined

by the fan width required for a specific job and by the orifice size that will supply the

desired amount of fluid and accomplish proper atomization.

For light viscosity fluids, smaller orifice tips generally are desired. For heavier

viscosity materials, larger orifice tips are preferred. Please refer to the chart below.

The following chart indicates the most common sizes and the appropriate materials to

be sprayed:

.011 - .013 Low Viscosity Materials 100 Mesh Filter

.015 - .019 Conventional Materials 50 Mesh Filter

.021 & larger High Viscosity Materials 5 Mesh Filter

Fan widths measuring 8" to 12" (20 to 30 cm) are most preferred because they offer

more control while spraying and are less likely to plug.

NOTE: Do not exceed the pump's recommended tip size.

REMEDY

1. Inspect connections for

air leaks

2. Disassemble and clean

3. Inspect and adjust

4. Inspect and replace

1. Replace

2. Adjust

3. Clean

1. Check fluid supply

2. Clean

3. Replace

PROBABLE CAUSE

1. Air in system

2. Dirty gun

3. Needle assembly out of adjustment

4. Broken or chipped seat

1. Worn or broken needle & seat

2. Needle assembly out of adjustment

3. Dirty gun

1. No paint

2. Plugged filter or tip

3. Broken needle in gun

PROBLEM

Spitting gun

Gun will not shut off

Gun does not spray

Troubleshooting — Airless Gun

CONDITION POSSIBLE CAUSE CORRECTION

TAILS Inadequate fluid delivery. Fluid not atomizing correctly.

Increase fluid pressure.

Change to smaller tip orifice size. Reduce fluid

viscosity. Reduce hose length.

Clean gun and filter(s).

Reduce number of guns using pump.

HOUR GLASS Inadequate fluid delivery. Same as above.

DISTORTED Plugged or worn nozzle tip. Clean or replace nozzle tip.

PATTERN EXPANDING & Suction leak. Inspect for suction hose leak.

CONTRACTING (SURGE)

Pulsating fluid delivery Change to a smaller tip orifice size.

Install pulsation dampener in system

or drain existing one. Reduce number of

guns using pump.

Remove restrictions in system; clean

tip screen if filter is used.

ROUND PATTERN Worn tip. Replace tip.

Fluid too heavy for tip. Increase pressure.

Thin material.

Change nozzle tip.

Troubleshooting — Spray Patterns

CONDITION POSSIBLE CAUSE CORRECTION

Oil motor stalls at bottom. Fluid pump piston seat unthreaded. If connecting rod is okay, remove cylinder head plug and pop valve down. Replace plug and start

(No unusual heat problems.) machine. If machine cycles up and stops at bottom again, then problem is piston seat on fluid pump.

Check piston seat. Repair or replace as necessary. If piston seat is okay and problem does not change,

check oil motor.

Valve sticking or oil motor trip rod shifter Remove valve and check for scratches and rough movement when sliding it up and down. Replace

assembly separated. valve and spool in this condition. Check trip rod for possible separation.

and spool in this condition. Check trip rod for possible separation.

Oil motor stalls at top. Valve sticking. Remove valve and check for scratches and rough movement when sliding it up and down. Replace

(No unusual heat problems) valve and spool in this condition.

Broken spring retainer (valve rod Replace valve rod assembly.

assembly)

Broken spring or valve rod. Replace valve rod assembly.

Air in hydraulic motor. Reset Valve.

Purge Air, generally accomplished by low pressure cycling of motor/pump assembly for 5 - 10 minutes.

Check for causes of air introduction.

• Loose fittings in tank.

• Loose fittings on hydraulic pump.

• Loose hose connections.

• Low oil in reservoir.

Air in fluid pump. Stall at top can occur randomly when fluid pump picks up air. Reset valve. Avoid air in the fluid pump.

Low pressure (okay on Blown piston seal. Before dismantling oil motor, start machine. With pump cycling under pressure, touch the hydraulic

down stroke, sluggish on cylinder and the head to see if cylinder or head gets hotter. This will help determine if piston seal.

up.stroke - high heat) is blown or piston nut is broken. If heat is on the head, check the o-rings on spool valve.

Note: Engine labors on

upstroke, idles back at stall

on the down stroke.

Cracked piston. Dismantle oil motor and check piston seals cylinder bore and piston nut. Pay special attention to piston

nut. It can be cracked and not show externally.

Low pressure (both strokes Blown center O-Rings on spool valve. Before dismantling oil motor, start machine. With pump cycling under pressure, touch the head to see if

- high heat) the head becomes hotter. This will help determine if center o-ring is blown on spool valve. If hot,

Note: Engine labors at stall remove and replace o-ring.

on both strokes

Bad hydraulic pump. Replace hydraulic pump.

Troubleshooting — Hydraulic Motors

Troubleshooting — Fluid Sections

CONDITION POSSIBLE CAUSE CORRECTION

Pump delivers on upstroke only or Lower foot valve ball is not seating due to Remove foot valve assembly. Clean and inspect. Test foot valve by filling with

goes up slowly and down fast. trash or wear. water; if ball fails to seal the seat, replace ball.

(Commonly called downstroke dive.)

Material too viscous to siphon. Thin material - contact manufacturer for proper thinning procedures.

Air leaking in on siphon side or damaged siphon Tighten all connections between pump and paint container. If damaged, replace.

hose. Siphon may be too small for heavy material Switch to larger diameter siphon set.

Pump delivers on down stroke only Upper ball is not seating due to trash or wear. Check upper seat and ball with water. If ball fails to seal seat, replace seat.

.or goes up fast and down slowly

Lower packing set is worn. Replace packing set if worn.

Pump moves up and down fast, Material container is empty or material is too thick Refill with new material. If too thick, remove siphon hose, immerse fluid section in

not delivering material. to flow through siphon hose material, and start pump to prime. Add thinner to material. Change to bigger siphon

. set. Open bleed valve to remove air and restart pump.

Bottom ball stuck to foot valve seat. Remove foot valve. Clean ball and seat.

Siphon hose is kinked or loose. Straighten.

Pump moves up and down slowly Loose connections. Bleed valve is open partially or Check all connections between pump and gun. Tighten as necessary. If material

when spray gun is shut off. bleed valve is worn. Lower packing seat is worn. is flowing from bleed hose, close bleed valve or replace if necessary. Should

none of the above be evident, replace lower packing.

Upper and/or lower ball not seating. Reseat balls by cleaning.

Not enough fluid pressure at gun. Spray tip is worn. Replace.

Outlet filter or gun filter is clogged Clean or replace filter.

Low voltage and/or inadequate amperage. Check electrical service. Correct as required.

Hose size or length is too small or too long. Increase hose size to minimize pressure drop through hose and/or reduce hose

length.

Pump chatters on up or down stroke Solvent has caused upper packing to swell. Replace packing.

Español

Seguridad

Este manual contiene información que debe leer y comprender antes de

usar el equipo. Cuando se encuentre con uno de los siguientes

símbolos, asegúrese de observar sus indicaciones de seguridad.

Este símbolo indica la existencia de un peligro potencial que puede

causar lesiones graves o la muerte. Después del mismo se incluye

información de seguridad importante.

Este símbolo indica la existencia de un peligro potencial para usted o el

equipo. Después del mismo se incluye información importante que indica

la forma de evitar daños al equipo o la forma de prevenir lesiones

menores.

PELIGRO: LESIÓN POR INYECCIÓN - La corriente de pintura de

alta presión que produce este equipo puede perforar la

piel y tejidos subyacentes, lo que conduciría a lesiones

serias y una posible amputación. Consulte de

inmediato a un médico.

NO TRATE LAS LESIONES POR INYECCIÓN COMO SI FUERAN

SIMPLES CORTADAS! Una inyección puede conducir a una

amputación. Consulte de inmediato a un médico.

El rango de operación máximo de la unidad es 3300 PSI / 228BAR

de presión de fluidos.

PARA PREVENIR:

• NO dirija NUNCA la punta de la pistola hacia alguna parte del

cuerpo.

• NO permita NUNCA que alguna parte del cuerpo tenga contacto

con la corriente del fluido. EVITE tener contacto con corrientes de

fluido que salgan de fugas que haya en la manguera.

• NO ponga NUNCA la mano enfrente de la manguera. Los guantes

no ofrecen ninguna protección contra lesiones por inyección.

• Bloquee SIEMPRE el gatillo de la pistola, apague la bomba de

fluido y libere toda la presión antes de dar mantenimiento, limpiar el

protector de la boquilla, cambiar la boquilla o dejar desatendido el

equipo. La presión no se liberará al apagar el motor. Para liberar

la presión debe girarse la perilla PRIME/SPRAY (cebar/atomizar)

hasta la posición PRIME. Consulte el PROCEDIMIENTO PARA

LIBERAR LA PRESIÓN que se describe en este manual.

• Mantenga puesto SIEMPRE el protector de la boquilla mientras

atomice. El protector de la boquilla ofrece cierta protección contra

lesiones por inyección pero es principalmente un dispositivo de

advertencia.

• Quite SIEMPRE la boquilla del atomizador antes de enjuagar o

limpiar el sistema.

• Pueden desarrollarse fugas en la manguera de pintura por causa

del desgaste, retorcimientos o el abuso. Una fuga es capaz de

inyectar el material en la piel. Cada vez que use la manguera de

pintura, inspecciónela antes.

• NO use nunca una pistola de atomización que no tenga un

bloqueador o un protector de gatillo puesto y que funcione.

• Todos los accesorios deben tener una capacidad de 3300 lb/pulg2 /

228BAR o mayor. Esto incluye las boquillas de atomizador,

pistolas, extensiones y mangueras.

PELIGRO: EXPLOSIÓN O INCENDIO - Los vapores de solventes y

pintura pueden explotar o incendiarse, causando con

esto lesiones severas y/o daños en la propiedad.

PARA PREVENIR:

• Debe proveerse un escape y aire fresco para hacer que el aire que

está dentro del área de atomización se mantenga libre de

acumulaciones de vapores inflamables.

NOTA PARA EL MÉDICO: La inyección dentro de la piel es una

lesión traumática. Es importante que la lesión se trate

quirúrgicamente tan pronto como sea posible . NO retrase el

tratamiento por investigar la toxicidad. La toxicidad es motivo

de preocupación con algunos revestimientos que se inyectan

directamente en la corriente sanguínea. Es recomendable

consultar a un cirujano plástico o reconstructor de manos.

ADVERTENCIA

NOTA: los avisos contienen información importante,

présteles especial atención.

PRECAUCION

ADVERTENCIA

• Evite todas las fuentes de ignición como son las chispas

electrostáticas, llamas abiertas, flamas de piloto, objetos calientes,

cigarros, y chispas que se generan al conectar y desconectar las

extensiones o de apagadores de luz que estén funcionando.

• No fume en la zona de trabajo.

• Debe haber un equipo para extinguir incendios permanentemente y

en buenas condiciones.

• Coloque la bomba para pintar en una zona bien ventilada. Los

gases inflamables a menudo son más pesados que el aire. La zona

del piso debe tener la debida ventilación. La bomba para pintar

contiene piezas que forman arcos que emiten chispas y pueden

encender los gases.

• El equipo que se utilice, así como los objetos que estén dentro y

alrededor del área de atomización, deben conectarse a tierra de

manera apropiada para prevenir las descargas eléctricas y las

chispas.

• Use solamente mangueras para fluidos de alta presión, conductoras

o conectadas a tierra, para aplicaciones sin aire. Asegúrese de que

la pistola esté conectada a tierra de manera apropiada, mediante

conexiones de manguera.

• El cable de alimentación debe enchufarse a un circuito aterrado

(eléctrico modela único).

• Siempre enjuague la unidad en un recipiente de metal por

separado, con presión baja en la bomba y sin la boquilla. Sostenga

la pistola firmemente contra el recipiente para ponerlo a tierra y

evitar chispas estáticas.

• Siga las advertencias y avisos de seguridad del fabricante de los

materiales y solventes.

• Tenga muchísimo cuidado al usar materiales cuyo punto de ignición

sea inferior a 70° F (21° C). El punto de ignición es la temperatura

a la cual pueden encenderse los vapores emanados por un fluido al

exponerlos a llamas o chispas.

• El plástico puede causar chispas estáticas. Nunca cuelgue plástico

en las ventanas ni en las puertas del área donde va a pintar. No

utilice plástico para proteger el piso cuando pinte materiales

inflamables.

• Cuando enjuague el equipo utilice la presión más baja posible.

MOTOR DE GAS (SEGÚN CORRESPONDA)

Coloque siempre la bomba fuera del edificio, al aire libre. Mantenga

todo solvente alejado del escape del motor. Nunca llene el tanque de

combustible si el motor está encendido o caliente. La superficie caliente

puede encender el combustible derramado. Conecte siempre un

conductor de tierra desde la unidad de la bomba a un objeto puesto a

tierra, por ejemplo una tubería de agua metálica. Consulte el manual del

motor para obtener información completa de seguridad.

PELIGRO: PELIGRO DE EXPLOSIÓN DEBIDO A MATERIALES

INCOMPATIBLES - Podría causar lesiones severas o

daños en la propiedad.

PARA PREVENIR:

• No utilice materiales que contengan blanqueador o cloro.

• No use solventes con hidrocarburos halogenados, tales como

productos para eliminar el moho, cloruro de metileno y 1,1,1 -

tricloroetano. Estos no son compatibles con el aluminio.

• Comuníquese con el proveedor del producto para obtener

información de compatibilidad con materiales de aluminio.

PELIGRO: GASES PELIGROSOS - Las pinturas, solventes,

insecticidas y otros materiales pueden ser perjudiciales

si se inhalan o entran en contacto con el cuerpo. Los

gases pueden causar náusea, desmayos o

envenenamiento graves.

PARA PREVENIR:

• Use una mascarilla respiratoria o careta siempre que exista la

posibilidad de que se puedan inhalar vapores. Lea todas las

intrucciones que vengan con la careta para estar seguro de que se

tendrá la protección necesaria contra la inhalación de vapores dañinos.

• Use gafas protectoras.

• Use ropa de protección, según lo requiera el fabricante del

producto.

PELIGRO: GENERAL - Puede causar daños en la propiedad o

lesiones severas.

PARA PREVENIR:

• Lea todas las instrucciones y advertencias de seguridad antes de

hacer funcionar cualquier equipo.

• Desconecte siempre el motor del suministro eléctrico antes de dar

servicio al equipo (eléctrico modela único).

• Observe todos los códigos locales, estatales y nacionales

apropiados que rigen las medidas de ventilación, prevención de

incendios y operación.

• Los Estándares de Seguridad del Gobierno de los Estados Unidos

se han adoptado bajo el Acta de Seguridad y Salud Ocupacionales

(OSHA por sus siglas en inglés). Deben consultarse estos

estándares, particularmente la parte 1910 de los Estándares

Generales y la parte 1926 de los Estándares de la Construcción.

• Utilice únicamente piezas autorizadas por el fabricante. El usuario

asume todos los riesgos y responsabilidades si usa piezas que no

cumplen con las especificaciones mínimas y dispositivos de

seguridad del fabricante de la bomba.

• Antes de usarla cada vez, revise todas las mangueras para ver que no

tengan cortadas, fugas, una cubierta desgastada por abrasión o con

abolladuras, así como uniones dañadas o que se hayan movido. Si

existiera cualquiera de estas condiciones, reemplace la manguera

inmediatamente. No repare nunca una manguera de pintura.

Reemplácela con otra manguera conectada a tierra.

• Todas las mangueras, soportes giratorios, pistolas y accesorios que

se usen con esta unidad deben tener una capacidad de presión de

3300 lb/pulg2 / 228BAR o mayor.

• No atomice en días con viento.

• Use ropa que evite el contacto de la pintura con la piel y el cabello.

Instrucciones para conectar a tierra

Los modelos eléctricos deben estar conectados a tierra. En caso de que

ocurra un corto circuito, la conexión a tierra reduce el riesgo de choque

eléctrico al proporcionar un alambre de escape para la corriente

eléctrica. Este producto está equipado con un cable que tiene un

alambre de conexión a tierra con un enchufe de conexión a tierra

apropiado. El enchufe se debe enchufar en una toma de corriente que

se haya instalado y conectado a tierra debidamente, de acuerdo con

todos los códigos y estatutos locales.

PELIGRO — Una instalación inapropiada del enchufe de conexión a

tierra puede dar como resultado el que exista un riesgo de choque

eléctrico. Si es necesario reparar o reemplazar el cable o el enchufe, no

conecte el alambre de conexión a tierra a ninguno de los terminales de

hoja planos. El alambre con aislamiento que tiene la superficie exterior

de color verde con franjas amarillas o sin ellas es el alambre de conexión

a tierra que debe conectarse al conector de conexión a tierra.

Verifique con un electricista o técnico de servicio calificado si las

instrucciones para conectar a tierra no le han quedado completamente

claras, o si duda que el producto haya quedado conectado a tierra de

manera apropiada. No modifique el enchufe que se proporciona. Si el

enchufe no entra en la toma de corriente, pídale a un electricista

calificado que instale la toma apropiada.

Este producto tiene una capacidad nominal de más de 15 amperios y es

para uso en circuitos con una capacidad nominal de 120 voltios, o bien,

el producto es para uso en circuitos con capacidad nominal superior a

120 voltios, y se equipa en la fábrica con un cable eléctrico y enchufe

específicos para permitir la conexión a un circuito eléctrico apropiado.

Asegúrese de que el producto esté conectado a una toma que tenga la

misma configuración que el enchufe. No se debe usar ningún adaptador

con este producto. Si es necesario cambiar la conexión de este

producto para uso en un circuito eléctrico diferente, la conexión debe ser

realizada por personal técnico calificado.

Use solamente extensiones trifilares que tengan un enchufe de

conexión a tierra de 3 hojas y un receptáculo de triple ranura que

acepte el enchufe del producto. Asegúrese de que su extensión

esté en buenas condiciones. Cuando use una extensión, asegúrese

de usar una que sea lo suficientemente resistente como para

soportar la corriente que descargue su producto. Un cable de un

tamaño menor causará una caída de voltage en la línea que dará

como resultado una pérdida de energía y un sobrecalenta|ôento.

Para las longitudes de menos de 15 metros se debe usar un cable

de extensión de 12 AWG. Si se utiliza un cable de extensión en el

exterior, tiene que estar marcado con el sufijo W-A después de la

designación del tipo de cable. Por ejemplo, SJTW-A para indicar

que el cable es apropiado para uso en exteriores.

PRECAUCION

Seguridad con los motores de gasolina

El escape del motor de esta unidad contiene químicos que el

Estado de California ha determinado causan cáncer, defectos de

nacimiento u otros daños al sistema reproductor.

1. Los motores Honda están diseñados para proporcionar un servicio

seguro y fiable, si se utilizan de acuerdo a las instrucciones. Lea y

entienda las instrucciones del Manual del Propietario de Honda

antes de utilizar el motor. De lo contrario, podría causar lesiones

personales o daño al equipo.

2. Para evitar peligros de incendio y para proporcionar una ventilación

adecuada, mantenga el motor por lo menos a 1 metro de los

edificios y de otro equipo durante su uso. No coloque objetos

inflamables cerca del motor.

3. Mantenga a los niños y las mascotas alejados de la zona de

trabajo, pues existe la posibilidad de quemaduras causadas por los

componentes calientes del motor o lesiones causadas por cualquier

equipo en el que se utilice el motor.

4. Sepa cómo apagar el motor rápidamente y comprenda el

funcionamiento de todos los controles. Nunca permita a nadie

operar el motor sin las instrucciones apropiadas.

5. La gasolina es extremadamente inflamable y es explosiva bajo

ciertas condiciones.

6. Llene el tanque de combustible en un lugar bien ventilado y con el

motor apagado. No fume ni permita que haya llamas ni chispas en

la zona de llenado ni en donde se almacena el combustible.

7. No llene en exceso el tanque de combustible. Después de ponerle

combustible, asegúrese de que la tapa del tanque esté cerrada

completamente.

8. Tenga cuidado de no derramar el combustible. Los gases del

combustible o el combustible derramado pueden encenderse. Si se

derrama combustible, asegúrese de que la zona esté seca antes de

encender el motor.

9. Nunca utilice el motor en un lugar encerrado o confinado. El

escape contiene gas de monóxido de carbono venenoso; la

exposición a este gas puede causar pérdida del conocimiento y

puede conducir a la muerte.

10. El escape se calienta mucho durante su uso y permanece caliente

durante un rato después de apagar el motor. Asegúrese de no

tocar el escape cuando esté caliente. Para evitar quemaduras

graves o peligros de incendio, deje que el motor se enfríe antes de

transportarlo o guardarlo bajo techo.

11. Nunca envíe ni transporte la unidad con gasolina en el tanque.

No utilice este equipo para rociar agua o ácido.

No cargue el equipo por el asa del carrito durante la carga y

descarga.

PRECAUCION

ADVERTENCIA

Français

Sécurité

Le présent manuel comprend des renseignements devant être lus

attentivement avant toute utilisation de l'appareil. Lorsque l'un des

symboles suivants apparaît, il est recommandé d'être particulièrement

attentif et de tenir compte des mesures de sécurité indiquées.

Ce symbole indique un danger potentiel pouvant causer des blessures

graves ou même mortelles. Des renseignements importants sur la

sécurité sont également indiqués.

Ce symbole indique un danger potentiel pouvant causer des blessures

corporelles ou des dommages à l'équipement. Des renseignements

importants sur la façon de prévenir tout dommage à l'équipement ou

toute blessure corporelle mineure sont également indiqués.

DANGER: BLESSURES PAR PERFORATION - Le jet de peinture à

haute pression produit par cet appareil peut perforer la

peau et les tissus sous-jacents et entraîner de sévères

blessures pouvant nécessiter une amputation.

Consultez immédiatement un médecin.

NE PAS TRAITER UNE BLESSURE PAR PERFORATION COMME

UNE SIMPLE COUPURE! Une perforation peut entraîner des risques

d'amputation. Consultez immédiatement un médecin.

Pression de service maximale du fluide dans l’appareil : 3300

lb/po2 / 228BAR.

MESURES PRÉVENTIVES:

• NE JAMAIS diriger le pistolet vers une quelconque partie du corps.

• NE JAMAIS mettre une quelconque partie du corps en contact avec

le jet de liquide. NE JAMAIS se mettre au contact d'un jet de liquide

provenant d'une fuite du flexible d'alimentation en liquide.

• NE JAMAIS placer votre main devant le pistolet. Des gants ne vous

protégeront pas contre les risques de blessures par perforation.

• TOUJOURS verrouiller la gâchette du pistolet, fermer la pompe à

liquide et décompresser l'appareil lorsque vous travaillez sur celui-ci,

nettoyez le protecteur de tête, remplacez la tête de pulvérisation ou

vous éloignez de l'appareil. Couper le moteur ne décompresse pas

l'appareil. Vous devez, pour le décompresser, placer le bouton

AMORÇAGE/PULVÉRISATION en position AMORÇAGE. Reportez-

vous, pour cela, à la PROCÉDURE DE DÉCOMPRESSION décrite

dans de ce manuel.

• TOUJOURS s'assurer que le protecteur de tête est en place lorsque

vous pulvérisez. Le protecteur de tête offre une certaine protection

contre les blessures par perforation mais sa principale fonction est

d'ordre préventif.

• TOUJOURS ôter la tête de pulvérisation avant de purger ou

nettoyer l'appareil.

• Le flexible d'alimentation en peinture peut fuir à la suite d'une usure,

de chocs ou de mauvais traitements. Une fuite peut entraîner une

perforation de la peau. Inspecter le flexible avant chaque utilisation.

• NE JAMAIS utiliser un pistolet dont la gâchette n'est pas munie d'un

loquet ou un cran de sécurité qui soit en état de fonctionner.

• Tous les accessoires doivent être homologués pour une pression

égale ou supérieure à 3300 lb/po2 / 228BAR. Cela s'applique, entre

autres, aux têtes de pulvérisation, aux accessoires du pistolet et aux

flexibles.

DANGER: RISQUES D'EXPLOSION OU D'INCENDIE - Les vapeurs

dégagées par le solvant ou la peinture sont explosives

et inflammables et peuvent causer des corporels

sérieux ou dommages matériels.

AVERTISSEMENT AUX MÉDECINS : Une perforation sous-

cutanée constitue un traumatisme. Il est important de traiter

la blessure de façon chirurgicale aussitôt que possible. NE

RETARDEZ PAS ce traitement pour des recherches de toxicité.

La toxicité n'est un risque que dans les cas où certains

produits de revêtement pénètrent dans le flux sanguin. Il peut

être nécessaire de faire appel à des soins de chirurgie

plastique ou de reconstruction de la main.

AVERTISSEMENT

NOTA : Les remarques donnent des renseignements

importants requérant une attention particulière.

ATTENTION

AVERTISSEMENT

MESURES PRÉVENTIVES:

• Veiller à éviter toute accumulation de vapeurs inflammables en vous

assurant que la zone où la pulvérisation a lieu est suffisamment

ventilée.

• Veiller à éviter la présence de toute source incandescente telle

qu'étincelle électrostatique, flamme nue, flamme-pilote, objet

brûlant, cigarette et étincelle provenant du branchement ou du

débranchement d'un cordon d'alimentation électrique ou d'un

commutateur.

• Ne pas fumer dans la zone d’épandage.

• Toujours avoir un extincteur en état de fonctionner à portée de la

main.

• Placer la pompe à peinture dans une zone bien aérée. Les vapeurs

inflammables sont souvent plus lourdes que l’air. Le plancher doit

être extrêmement bien aéré. La pompe à peinture contient des

pièces pouvant créer des étincelles et enflammer les vapeurs

présentes dans l’air.

• Le matériel utilisé, ainsi que les objets se trouvant à proximité de la

zone de pulvérisation, doivent être convenablement reliés à la terre

afin d'éviter toute étincelle ou toute décharge électrostatique.

• N'utiliser que des flexibles d'alimentation en liquide à haute

pression conducteurs ou reliés à la terre dans les cas d'utilisation

sans air comprimé. S'assurer que le pistolet est convenablement

relié à la terre par l'intermédiaire du flexible.

• Le cordon d’alimentation doit être raccordé à un circuit mis à la terre

(les modèles électriques seulement).

• Toujours purger l’appareil dans un contenant métallique séparé, en

s’assurant que la pompe soit à basse pression et que le chapeau

soit retiré. Tenir le pistolet fermement contre la paroi du contenant

pour mettre celui-ci à la terre et empêcher l’émission d’étincelles

causées par l’électricité statique.

• Se conformer aux consignes et recommandations de sécurité du

fabricant du solvant ou du produit.

• S’entourer de toutes les précautions possibles lorsqu’on utilise des

produits ayant un point d’éclair inférieur à 21 °C (70 °F). Le point

d’éclair d’un fluide est la température à laquelle les vapeurs

émanant du fluide peuvent s’enflammer au contact d’une flamme ou

d’une étincelle.

• Le plastique peut être une source d’étincelles provoquées par

l’électricité statique. Ne jamais utiliser une couverture en plastique

pour fermer une zone d’épandage ni utiliser des toiles de protection

en plastique lors de la pulvérisation de matières inflammables.

• Lorsque vous purgez l'appareil, veillez à utiliser à la pression

minimale.

MOTEUR À ESSENCE (DANS LES CAS OÙ CELA S’APPLIQUE)

Toujours placer la pompe à l’extérieur de la structure à l’air frais. Garder

tous les solvants loin de l’échappement du moteur. Ne jamais remplir le

réservoir à carburant lorsque le moteur est en marche ou lorsqu’il est

chaud ; les surfaces chaudes risquent d’enflammer le carburant déversé

accidentellement. Toujours raccorder un fil de mise à la terre entre la

pompe et un objet mis à la terre, tel qu’une conduite d’eau métallique. Se

reporter au guide d’utilisation du moteur pour obtenir de plus amples

renseignements concernant la sécurité.

DANGER: RISQUES D'EXPLOSION PAR INCOMPATIBILITÉ DES

MATÉRIAUX - Peuvent être à l'origine de corporels

sérieux ou dommages matériels.

MESURES PRÉVENTIVES:

• Ne pas utiliser de matériaux contenant des agents de blanchiment

ou du chlore.

• Ne pas utiliser des solvants à base d’hydrocarbure halogéné tels

que l’agent anticryptogamique, le chlorure de méthylène et le

trichloro-éthane-1,1,1. Ces produits ne sont pas compatibles avec

l’aluminium

• Communiquer avec votre fournisseur de revêtement pour connaître

la compatibilité du matériau avec l’aluminium.

DANGER: VAPEURS NOCIVES – la peinture, les solvants, les

insecticides et autres matériaux peuvent être nocifs

lorsqu’ils sont inhalés ou en contact avec le corps. Les

vapeurs peuvent causer une nausée importante, des

évanouissements ou un empoisonnement.

MESURES PRÉVENTIVES:

• Utiliser un respirateur ou un masque chaque fois qu'il y a des

risques d'inhalation de vapeurs. Lire attentivement toutes les

instructions se rapportant au masque pour vérifier que celui-ci vous

assure une protection suffisante contre les vapeurs toxiques.

• Porter des lunettes de protection.

• Porter des vêtements de protection, conformément aux directives du

fabricant de revêtement.

DANGER: GÉNÉRALITÉS - Peut causer des dommages matériels

ou corporels sérieux.

MESURES PRÉVENTIVES:

• Avant d'utiliser tout équipement, lire attentivement toutes les

instructions et les consignes de sécurité

• Toujours débrancher le moteur de l’alimentation électrique avant

d’effectuer des travaux sur l’appareil (les modèles électriques

seulement).

• Se conformer à la législation locale, provinciale ou fédérale pour tout

ce qui concerne la ventilation, la prévention des incendies et les

conditions générales d'utilisation.

• Les normes de sécurité du Gouvernement américain sont régies par

le Occupational Safety and Health Act (OSHA). Il est important de

consulter ces normes, en particulier la section 1910 sur le normes

générales et la section 1926 sur les des normes de la construction.

• N’utiliser que les pièces autorisées par le fabricant. L’utilisateur

assume tous les risques et responsabilités lorsqu’il utilise des

pièces qui ne sont pas conformes aux caractéristiques techniques

minimales ainsi qu’aux dispositifs de sécurité du fabricant de la

pompe.

• Vérifier, avant toute utilisation, que les flexibles ne présentent pas

d'entaille ou de fuite, que le couvercle ne soit pas gonflé et que les

raccords ne soient pas endommagés. Si le flexible a subi l'un des

dommages précités, remplacez-le immédiatement. Ne jamais

réparer un flexible d'alimentation en peinture. Le remplacer par un

autre flexible mis à la terre.

• Tout flexible, raccord orientable, pistolet et accessoire utilisé avec

cet appareil doit pouvoir fonctionner à une pression égale ou

supérieure à 3300 lb/po2 / 228BAR.

• Ne jamais pulvériser lorsqu'il vente.

• Porter des vêtements pour protéger la peau et les cheveux contre

tout contact avec la peinture.

Instructions de mise à la terre

Les modèles électriques doivent être mis à la terre. La mise à la terre

réduit les risques d'électrocution lors d'un court-circuit en permettant au

courant de s'écouler par le fil de mise à la terre. Cet appareil est muni

d'un cordon électrique avec fil de mise à la terre ainsi que d'une fiche de

terre. La fiche doit être branchée sur une prise installée correctement et

mise à la terre conformément à la réglementation et aux codes en

vigueur.

DANGER — Une prise de terre mal branchée peut être à l'origine

d'électrocutions. S'il s'avère nécessaire de réparer ou de remplacer le

cordon électrique ou la fiche, ne pas brancher le fil vert de mise à la terre sur

l'une ou l'autre des bornes à broche plate. Le fil recouvert d'un isolant vert

avec ou sans rayures jaunes est le fil de mise à la terre et doit être branché

sur la broche de mise à la terre.

Si vous ne comprenez pas les instructions de mise à la terre ou si vous

n'êtes pas sûr que l'appareil est correctement mis à la terre, contactez un

électricien agréé. Ne pas modifier la fiche d'origine. Si la prise ne

convient pas à la fiche, faites installer la prise adéquate par un électricien

agréé.

Ce produit a une intensité nominale de plus de 15 ampères et doit être

utilisé sur un circuit de 120 volts ou plus. Il doit en outre être muni en

usine d’un cordon électrique et d’une fiche spécifiques permettant son

raccordement à un circuit électrique approprié. S’assurer que le produit

soit branché sur une prise ayant la même configuration que la fiche. Ne

pas utiliser d’adaptateur avec ce produit. Si le produit doit être branché à

nouveau pour être utilisé sur un circuit électrique de type différent, le

raccordement doit être effectué par un personnel de service qualifié.

Utiliser uniquement une rallonge à trois fils munie d'une fiche de

terre dans une prise secteur mise à la terre correspondant au type

de fiche de l'appareil. S'assurer que votre rallonge est en bon état.

Lorsque vous utilisez une rallonge, assurez-vous qu'elle soit d'un

calibre suffisant pour supporter l'intensité du courant requise par

l'appareil. Une rallonge trop mince entraîne une chute de tension,

une diminution de l'intensité et une surchauffe. Pour les longueurs

inférieures à 15,2 mètres (50 pi), utiliser des rallonges de calibre 12

AWG. Si vous devez utiliser une rallonge à l’extérieur, celle-ci doit

comprendre la marque W-A après la désignation indiquant le type

de cordon. Par exemple, la désignation SJTW-A indique que le

cordon est conçu pour être utilisé à l’extérieur.

ATTENTION

Sécurité du moteur à essence

L’État de la Californie reconnaît que les gaz d’échappement de cet

appareil contiennent des produits chimiques susceptibles de

causer le cancer, des malformations congénitales ou pouvant être

nocifs pour le système reproducteur.

1. Les moteurs Honda sont conçus pour être fiables et sécuritaires

lorsqu’ils sont utilisés selon les directives. Lire et comprendre le

guide d’utilisation de Honda avant de faire fonctionner le moteur. Le

non-respect de cet avertissement risque de causer des blessures

graves ou d’endommager l’appareil.

2. Afin de prévenir les risques d’incendie et d’assurer une ventilation

adéquate, garder le moteur à une distance d’au moins un mètre (3

pi) des bâtiments et des autres appareils durant le fonctionnement.

Ne pas placer des objets inflammables près du moteur.

3. Les enfants et les animaux doivent être tenus à l’écart de la zone

de fonctionnement de l’appareil afin d’éviter les risques de brûlures

causées par les composants chauds du moteur ou par les

équipements utilisés avec le moteur.

4. Savoir comment couper le moteur rapidement et bien comprendre le

fonctionnement de toutes les commandes. Ne jamais laisser

quiconque utiliser le moteur sans lui avoir d’abord fourni les

directives appropriées.

5. Le carburant est une matière extrêmement inflammable et peut

exploser sous certaines conditions.

6. Ravitailler en carburant dans un endroit bien aéré une fois le

moteur arrêté. Ne pas fumer et s’assurer qu’il n’y ait ni flammes ni

étincelles dans la zone de ravitaillement ou d’entreposage du

carburant.

7. Ne pas trop remplir le réservoir d’essence. Après le ravitaillement,

s’assurer que le bouchon du réservoir soit bien fermé et serré.

8. Prendre soin de ne pas renverser de carburant lors du

ravitaillement, car les vapeurs émanant du carburant ou le carburant

déversé accidentellement peuvent s’enflammer. En cas de

déversement, s’assurer que l’endroit soit complètement sec avant

de démarrer le moteur.

9. Ne jamais mettre le moteur en marche dans un endroit fermé ou

restreint, car les gaz d’échappement contiennent des matières

toxiques, telles que le monoxyde de carbone, susceptibles de

provoquer des évanouissements ou même d’entraîner la mort.

10. Le silencieux devient très chaud durant le fonctionnement et le

demeure pendant un certain temps une fois le moteur arrêté.

S’assurer d’attendre quelques minutes avant de toucher au

silencieux. Pour éviter les risques de brûlures graves ou d’incendie,

laisser le moteur se refroidir avant de le transporter ou de

l’entreposer à l’intérieur.

11. Ne jamais expédier ou transporter l’appareil lorsque le réservoir est

rempli de carburant.

Ne pas utiliser cet appareil pour vaporiser de l’eau ou de l’acide.

Ne pas soulever par la poignée du chariot lors du chargement ou du

déchargement.

ATTENTION

AVERTISSEMENT

One Gun Two Guns

Item

Part # Description 759-500 759-501

1 335-108 Motor/pump assembly....................................1....................1

2 930-515 Filter assembly, outlet manifold......................1....................1

3 759-038 Second gun assembly ..........................................................1

4 520-100 Airless Gun.....................................................1 ....................2

5 840-212 Bleed line assembly w/ valve.........................1....................1

6 103-828 Siphon hose assembly...................................1....................1

7 506-102 Convertokit, 5.5 HP, Honda, gasoline ............1....................1

8 759-001 Cart assembly ................................................1 ....................1

9 424-620 Line pointer (not shown) ................................1 ....................1

10 ---------- SC-5 striping tips (optional, see below for part numbers)

645-1502 645-1504 645-1506 645-1702

645-1704 645-1706 645-1904 645-1906

645-2104 645-2106

Parts Lists and Service Instructions

Main Assembly — Gas Model

Gas Convertokits (P/N 506-102)

Item

Part # Description Quantity

1 860-502 Stop nut.................................................8

2 860-004 Flat washer............................................8

3 980-331 Engine, gas 5.5 HP, Honda...................1

4 980-307 Key ........................................................1

5 448-241 Pulley ....................................................1

6 449-144 Bracket ..................................................1

7 858-601 Nut.........................................................1

8 858-636 Screw ....................................................1

9 424-273 Spring....................................................1

10 858-611 Lock nut.................................................1

11 449-165 Vibration pad.........................................4

12 424-286 Mounting plate.......................................1

13 424-285 "V" belt (not shown) ...............................*

*Not part of this assembly

DC — Electric Convertokit

506-217 506-214

Item

Part # Description Qty. Qty.

1 978-350 Motor, DC-Electric, 2 HP

50/60 Hz, 115 V .....................1

978-351 Motor,DC-Electric, 2 HP

50/60 Hz, 220 V.......................................1

2 860-501 Stop nut .................................4................4

3 860-002 Lock washer...........................4................4

4 977-227 Pulley .....................................1................1

5 448-337 Mounting plate .......................1................1

6 590-068 Handle grip ............................1................1

7 335-017 Handle ...................................1................1

8 860-004 Flat washer ............................8................8

9 860-535 Screw.....................................2................2

10 860-552 Screw.....................................2................2

11 506-259 Cover .....................................1................1

12 506-260 ON/OFF switch ......................1................1

13 506-258 Fan (not shown).....................1................1

14 506-255 Bridge rectifier (not shown)....1................1

15 449-285 "V" belt (not shown) ...............* ................*

*Not part of this assembly

Electric Convertokits Service Instructions

Before servicing the electric motor, follow the “Pressure

Relief Procedure” in the Cleanup section of this manual.

Once you have completed this procedure, unplug the

power supply cord. Failure to reduce pressure can result

in serious injury. Observe all warnings.

1. Remove both inspection covers on motor.

2. Push in the spring clip to unhook it, then pull it out..

3. Loosen the terminal screw. Pull the brush lead away, but

leave the motor lead in place. Remove the brush and

spring.

4. Inspect the commutator for burning, excessive pitting or

gouging. A black color on the commutator is normal.

5. Install the new brush so its lead slides in the long slot of

the brush holder. Push the terminal under the terminal

screw washer. Ensure the motor lead is still connected at

the screw. Tighten the screw.

6. Place the spring on the brush as shown above. Push in

and hook the spring clip. Repeat this procedure for the

other side. Reinstall the inspection covers.

Brush

Brush Holder

Terminal Screw

Spring

Spring Clip

Commutator

Terminal Screw

Spring Clip

Brush Lead

Inspection

Cover

NOTE: Brushes should be replaced when they are

worn to less than 1/2 inch. Check and replace

both brushes at the same time. Brush Repair

Kit, Part No. 978-050, consists of: 2 brushes, 2

springs, and 2 clips.

WARNING

Included with

item 41.

Cart Assembly (P/N 759-001)

Item Part # Description Quantity

1 424-281 Caster ..................................1

2 756-157 Screw...................................4

3 866-004 Washer ................................4

4 866-210 Nut .......................................4

5 756-034 Knob, clamp.........................4

6 757-022 Rod, clamp ..........................2

7 759-025 Frame, base ........................1

8 759-017 Bucket holder, domestic ......1

9 759-008 Cable, caster lock................1

10 759-020 Handle .................................1

11 756-136 Lever assembly ...................1

12 759-018 Screw...................................2

13 759-019 Nut .......................................2

14 424-271 Clamp ..................................1

15 759-024 Screw...................................4

16 858-002 Washer ................................6

17 858-611 Nut .......................................4

18 424-269 Brake pad ............................1

19 862-401 Nut .......................................2

20 860-004 Washer ................................2

21 757-014 Bar .......................................1

22 757-055 Plastic end cap ....................1

23 862-468 Screw...................................2

24 862-001 Washer ..............................10

25 862-410 Nut .......................................8

26 759-026 Screw...................................6

27 757-089 Slide.....................................1

28 759-110 Screw...................................3

29 756-029 Block....................................1

30 424-226 Clamp ..................................1

31 862-436 Screw...................................1

32 862-002 Washer ................................5

33 424-224 Arm, support........................1

34 759-042 Block radius lock .................1

35 424-247 Cable clip.............................4

36 870-404 Nut, castle............................2

37 756-079 Pin, cotter ............................2

38 424-216 Cable, gun control ...............1

39 756-130 Clamp ..................................2

40 761-405 Snap ring .............................2

41 757-050 Wheel ..................................2

42 759-027 Axle, cart..............................1

47 757-091 Pail cover.............................1

49 226-001 Nut .......................................2

50 770-720 Screw...................................2

51 759-031 Control guide .......................1

52 759-035 Strap, lever ..........................2

53 757-092 Screw...................................2

54 759-043 Bumper, rubber....................1

54a 770-596 Washer ................................1

55 757-130 Seal .....................................2

56 756-154 Screw...................................2

61 424-201 Gun holder...........................1

62 858-912 Screw...................................1

63 756-035 Clamp ..................................1

64 424-229 Grease fitting .......................2

66 858-637 Screw...................................1

67 424-202 Lever....................................1

68 858-601 Nut .......................................1

69 424-248 Bearing ................................2

70 860-936 Screw...................................1

71 858-653 Screw...................................1

72 424-249 Bearing ................................1

73 858-603 Nut .......................................1

74 858-636 Screw...................................2

75 858-002 Washer ................................2

76 424-245 Handle grip ..........................2

77 759-012 Pin, caster lock ....................1

78 759-013 Guide block..........................1

79 700-784 Screw...................................4

80 759-016 Screw...................................1

81 756-087 Spring ..................................1

82 759-014 Block cover..........................1

85 424-221 Support bracket ...................1

86 862-460 Bolt ......................................2

87 757-096 5 gallon pail (not shown) .....1

Belt Guard Assembly

Item Part # Description Quantity

1 862-411 Nut ........................................................1

2 862-002 Lock washer..........................................1

3 448-670 Belt guard .............................................1

4 862-001 Flat washer ...........................................2

5 862-428 Screw....................................................1

Hydraulic System

Item Part # Description Quantity

1 420-250 Tubing, PTFE................................................1

2 449-126 Hose clamp ...................................................1

3 431-042 Tube connector .............................................1

4 192-228 Elbow ............................................................1

5 448-243 Pressure adjustment knob ............................1

6 449-751 Hydraulic pump .............................................1

7 448-494 Key, pump (.156 x .156 x 1

3/16

) ......................1

8 860-520 Set screw ......................................................1

9 448-250 Pulley/fan assembly ......................................1

10 325-031 O-ring ............................................................1

11 860-528 Screw ............................................................1

12 860-002 Flat washer ...................................................2

13 424-283 Chain, 20” .....................................................1

14 449-616 Tank cover.....................................................1

15 858-609 Clinch nut ......................................................1

16 859-001 Washer..........................................................2

17 858-621 Socket screw.................................................2

18 858-624 Screw ............................................................2

19 449-605 Tank gasket...................................................1

20 112-208 Nipple ............................................................1

21 472-500 Elbow, street .................................................1

22 448-208 Inlet screen ...................................................1

23 449-602 Hydraulic tank ...............................................1

24 862-411 Flex lock nut..................................................2

25 862-001 Flat washer ...................................................6

26 862-002 Lock washer..................................................4

27 862-496 Tap bolt .........................................................1

28 449-176 Belt guard brace............................................1

29 941-555 Ball valve.......................................................1

30 424-211 Return hose assembly ..................................1

31 424-284 Pressure hose assembly...............................1

32 192-051 Elbow ............................................................1

33 451-044 Fitting ............................................................1

34 449-626 Filler cap w/ dipstick......................................1

35 449-614 Tube assembly..............................................1

36 449-609 Hydraulic By-Pass.........................................1

37 449-610 Hydraulic filter ...............................................1

38 858-636 Screw, HH .....................................................8

39 858-002 Lock washer................................................10

40 101-205 Ground lug ....................................................1

41 860-502 Nut.................................................................1

42 862-438 Thumb screw ................................................1

43 862-402 Acorn nut.......................................................1

44 449-107 Mounting plate retainer .................................1

45 449-135 Spacer...........................................................1

46 862-493 Screw, HH .....................................................2

47 862-480 Screw, HH .....................................................1

48 227-027 Plug ...............................................................1

Torque and Sealant Guide

Item Description

3 Use Hydraulic Sealant

9 Use Blue Loctite on threads

17 Use Blue Loctite on threads

17 Torque to 8 FT/LBS (11 Nm)

18 Torque to 8 FT/LBS (11 Nm)

20 Use Hydraulic Sealant

21 Use Hydraulic Sealant

22 Use Hydraulic Sealant

27 Torque to 15 FT/LBS (20,5 Nm)

33 Use Hydraulic Sealant

37 Torque to 20 FT/LBS (28 Nm)

45 Torque to 15 FT/LBS (20,5 Nm)

46 Torque to 15 FT/LBS (20,5 Nm)

Hydraulic Motor Service Instructions

Disassembly

1. Disconnect the high pressure hose line from the elbow (31

and 32 in Hydraulic System parts list) on the back of the

rotary pump.

2. Remove the two mounting bolts and two lock washers (86

and 32 in Cart Assembly parts list) that attach the

motor/pump assembly to the cart.

3. Place the motor/pump assembly in a vise, holding it securely

by the motor/pump block (25, in Hydraulic Motor parts list).

Disassembly of Hydraulic Motor

Disassembly of the hydraulic motor must be carried out in an

absolutely clean area. Any dust or metallic particles left in the

motor or entering it on reassembly may damage the critical parts

and affect its service life and warranty. If the hydraulic motor is

operable, start the machine and place the hydraulic piston rod

(21) in its top position. The numbers in parentheses refer to the

Hydraulic Motor parts list on the following page.

1. Remove cylinder head plug (7).

2. Loosen lock ring (22) with a spanner wrench and unthread

tube retaining nut on tee (27). Loosen tube retaining nut on

elbow (15). Slide the nut down. Push motor tube (26) into

tee (27) far enough to clear elbow (15). Slowly unthread

cylinder head (11) and Iift it just high enough above the

cylinder (23) to reach the valve rod assembly (20) with vise

grip pliers.

3. The hydraulic piston rod (21) should be near the top of its

stroke for disassembly. It may be necessary to use a wood

or nylon driver to push the hydraulic piston rod up to its top

position.

4. Grip the valve rod securely with vise grip pliers and then

remove the FlexLoc nut (9) from the top of the valve rod

assembly (20). Be careful that the spool (5) does not fall.

The cylinder head (11) can now be lifted off. Unthread the

cylinder (23) from the motor/pump block (25). Note: An extra

lock ring (22) can be used to jam the two lock rings together

on the cylinder and a pipe wrench can be used to unthread

the cylinder (23) from the motor/pump block (25).

5. To remove connecting rod pin (2, in Fluid Pump parts list),

slide the ring up with a small screwdriver, and then push the

connecting rod pin out (see illustration on pg. 24).

6. Remove the hydraulic piston rod assembly from the

motor/pump block (25).

7. Remove rod seal (24), being extremely careful not to scratch

the seal groove in the motor/pump block (25).

8. Place the piston retainer screw (16) on the hydraulic piston

rod assembly in a vise. Slide a long bar through the hole at

the base of the hydraulic piston rod for leverage, and

unthread the hydraulic piston rod from the piston retainer

screw.

9. Remove piston (17) and lift out valve rod assembly (20).

10. Remove piston seal (18) and o-ring (19).

11. Remove trip retainers (1), trip springs (3), and balls (4) from

cylinder head (11). Remove o-rings (2) from trip retainers (1).

12. Remove retaining ring (14) and sleeve retainer (13). Gently

tap spool/sleeve set (5) out of cylinder head (11) using a

wood or nylon rod.

13. Inspect hydraulic piston rod (21) and cylinder (23) for wear,

scratches, and dents. Replace if damaged.

14. Inspect spool valve (5) for wear. Replace if necessary. spool

valve should move smoothly and freely with no force by

holding in a vertical position. If it does not, it can cause the

motor to stall.

NOTE: Reassembly of this motor should be carried out in

a clean, dust free area only. It is recommended

that a full “Motor Service Kit, Minor” (P/N 235-050)

be on hand. All parts should be inspected for

absolute cleanliness. Any paricles of dust or metal

will affect the service life of the sealed motor and

hydraulic system.

Hydraulic Motor

Before servicing the electric motor, follow the “Pressure

Relief Procedure” in the Cleanup section of this manual.

Once you have completed this procedure, unplug the power

supply cord. Failure to reduce pressure can result in

serious injury. Observe all warnings.

WARNING

Torque flex locknut to

10 ft./lbs. (146N/m).

Use blue Loctite.

Use blue

Loctite on

lock ring.

Use

hydraulic

sealant.

Seal lip must

face up.

Use

hydraulic

sealant.

Torque head plug to

15 ft./lbs. (219 N/m).

Do not over-tighten

o-ring seal.

Torque trip

retainers to

15 ft./lbs. (365 N/m).

Do not over-tighten

o-ring seal.

Torque piston

retainers to

75 ft./lbs. (1095 N/m).

Use red Loctite.

Seal lip must

face down.

Valve rod assembly

is factory set and

permanently Loctited.

Do not disassemble.

27a

See page 29 for

installation

instructions.

Item Part #

Description Quantity

1 235-018 Trip retainer.........................................2

2 141-007 O-ring..................................................2

3 325-005 Trip spring, .........................................2

4 569-016 Ball, SS ...............................................2

5 441-908 Spool / sleeve set ...............................1

6 441-152 O-ring..................................................3

7 235-030 Cylinder head plug..............................1

8 441-217 O-ring..................................................1

9 858-811 Flex lock nut .......................................1

10 451-121 Male elbow, 90º ..................................1

11 235-112 Cylinder head......................................1

12 431-032 O-ring..................................................2

13 431-053 Sleeve retainer....................................1

14 431-054 Retainer ring .......................................1

15 192-000 Elbow ..................................................1

16 235-022 Piston retainer screw ..........................1

17 235-008 Piston..................................................1

18 235-027 Piston seal ..........................................1

19 235-026 O-ring..................................................1

20 235-021 Valve rod assembly.............................1

21 235-948 Hydraulic piston rod............................1

22 235-001 Lock ring .............................................1

23 235-007 Cylinder...............................................1

24 235-028 Rod seal..............................................1

25 235-923 Motor/pump block ...............................1

26 235-029 Motor tube...........................................1

27 197-031 Tee ......................................................1

27a 431-019 O-ring kit .............................................1

28 700-499 O-ring..................................................1

Reassembly of Hydraulic Motor

1. Separate spool/sleeve set (5). Place o-rings (6) onto sleeve.

Lubricate o-rings with hydraulic oil. Gently push the sleeve

into cylinder head (11) with the flatter side of the sleeve facing

out. Use a nylon rod to tap sleeve down until it reaches its full

depth. Do not use any other type of tool that might damage or

leave particles or residue on the sleeve. Install the spool

through the top of the cylinder head, down into the sleeve.

Do not use Piston Lube pump packing lubricant. It is a

solvent and will severely damage seals and O-Rings of the

hydraulic motor.

2. Install o-rings (2) on trip retainers (1). Install trip retainer balls

(4) followed by springs (3) which, when installed, will hold

spool/sleeve set (5) in proper place for assembly.

3. Install sleeve retainer (13) followed by snap ring (14) into

cylinder head (11), which will hold valve sleeve in place.

Install o-ring (12) in the o-ring groove of the cylinder head.

4. Replace lower seal (24) in motor/pump block (25). Be sure

the open portion of the seal is facing upward (V). This seal

requires no special tool.

5. Place hydraulic piston rod (21) in vise. Inspect valve rod

assembly (20) for any damage. Make sure the lock nut at

the bottom of the valve rod assembly (20) is secure. DO

NOT remove. Then, place into hydraulic piston rod (21) as

illustrated. Install o-ring (19), lubricating it well and replacing

piston (17) onto hydraulic piston rod (21). Put one drop of

blue Loctite on the piston retainer screw (16). Tighten piston

retainer screw until piston is locked into place. Check valve

rod assembly (20) for normal spring action at this time.

6. Install piston seal (18) with lips facing downward. Carefully

install piston seal (18). Expand the ring and stretch it

sufficiently for installation.

7. With motor/pump block (25) still in vise, install rod seal (24)

by pushing it towards its groove with a properly sized blunt

rod. Then complete installation with the fingers. No tool is

necessary. Do not twist the seal.

CAUTION

8. Pre-lubricate the piston and valve rod assembly with

Coolflo™ hydraulic fluid (P/N 430-361). Install hydraulic

piston rod (21) into motor/pump block (25) with a gently

pushing and rotating motion to work the hydraulic piston rod

in through the seal (24).

9. Replace the connecting rod pin and retainer ring. See

illustration below.

10. Install o-ring (12) on cylinder wall. Lubricate ring and inner

wall. With the hydraulic piston rod held firmly, the cylinder

should be gently driven over the piston seal with a rubber

mallet. Tightly thread the cylinder into motor/pump block (25).

11. Raise hydraulic piston rod (21) to top position and thread lock

ring (22) all the way up on upper threads of cylinder (23).

12. Pull valve rod assembly (20) up as far as it will travel and

grasp it with vise grip pliers. Then install cylinder head (11),

already assembled, over valve rod until the top threads of

the valve rod pass through the top of the spool/sleeve set

(5). The valve rod threads must be clean and free of oil.

Place one drop of blue Loctite on threads of flex lock nut (9)

and thread nut onto valve rod to full tight position (do not

over-tighten) while holding valve rod below with vise grip

pliers.

13. Thread cylinder head (11) down onto the cylinder (23) and

then back off just enough to reassemble hydraulic fittings

and motor tube (26). Tighten lock ring with spanner wrench

to hold cylinder head in position.

14. The tee assembly (27) and the elbow (15) use an o-ring

(27a) to seal on the outer diameter (O.D.) of the motor tube

(26). The O.D. of the motor tube should be free of scratches

or sharp edges. The lock nuts on these fittings first should

be hand tightened, then wrench tightened another half turn.

15. Install o-ring (8) onto cylinder head plug (7). Tighten.

Motor Service Kit, Minor (P/N 235-050)

Item

Part # Description Quantity

2 141-007 O-ring....................................................2

3 325-005 Trip spring.............................................2

4 569-016 Ball, SS .................................................2

6 441-152 O-ring....................................................3

8 441-217 O-ring....................................................1

9 858-811 Flex lock nut .........................................1

12 431-032 O-ring....................................................2

18 235-027 Piston seal ............................................1

19 235-026 O-ring....................................................1

24 235-028 Rod seal................................................1

Connecting Pin Arrangement

NOTE: Inspect the bottom of hydraulic piston rod (21)

for nicks or sharp areas that could damage the

piston seal during installation through the pump

block (25).

Fluid Pump

Fluid Pump Service Instructions

IMPORTANT: Use of non-Speeflo manufactured service

parts my void warrranty. Ask for original

parts made by Speeflo for best services.

This fluid pump should receive a routine

servicing after approximately 1,000 hours

of use. Earlier servicing is required if there

is excessive leakage from the top packing

or if pump strokes become faster on one

stroke or the other. The use of Speeflo

Piston Lube (P/N 700-925) is recommended

as an upper packing lubricant. Do not

substitute oil, water, or solvent for an upper

packing lubricant.

Peaks of upper

packings must

face up.

Torque piston

retainers to

75 ft./lbs.

(1095 N/m).

Use blue

Loctite.

Wet cup area

for piston lube

packing

lubricant.

Peaks of lower

packings must

face down.

Lubricate O-ring.

PTFE tape

siphon hose

Disassembly

1. Remove siphon tube assembly. Unthread foot valve (16)

and pump cylinder (12) with strap wrench.

2. Slide the retainer ring (1) up with a small screwdriver, then

push the connecting pin (2) out.

3. Pull displacement rod (6) through the lower cavity of the

motor/pump block.

4. Remove the motor/pump block, PTFE o-ring (3), upper

packing spring (5), and upper packing set (4).

5. Hold displacement rod (6) in a vise by the flats at the top of

the displacement rod and remove piston seat (11) with

wrench while holding the displacement rod horizontal with

wooden support, if necessary. Remove ball (10), lower

packing set (4), lower packing spring (9), sleeve (8), and

spring retainer (7).

6. Remove ball cage (14), PTFE o-ring (3), and ball (15).

7. Replace connecting pin (2) and retainer ring (1) .

8. Remove o-ring (13) from pump cylinder (12)

Reassembly

1. Place ball (15) into foot valve (16), followed by ball cage

(14).

2. Insert PTFE o-ring (3) into lower groove of foot valve (16).

3. Place lower packing set (4) onto piston seat (11) with the

peak of the “V” packings pointing down toward the foot

valve.

4. Clean the threads on piston seat (11) and coat the threads

with blue Loctite. Make sure no Loctite is on the seat.

5. Place ball (10) onto piston seat (11).

6. Place lower packing spring (9) onto piston seat (11),

followed by sleeve (8) and spring retainer (7).

7. Screw displacement rod (6) and piston seat (11) together.

Tighten in a vise to 75 ft./lbs.

8. Insert PTFE o-ring (3) into upper grove of the motor/pump

block.

9. Insert upper packing set (4) into the motor/pump block with

the peak of the “V” packings pointing up toward the motor.

10. Place upper packing spring (5) into the motor/pump block

with the small tapered end facing up toward the motor/pump

block.

11. Insert displacement rod (6) up through the upper packings in

the motor/pump block.

12. Align the holes in displacement rod (6) and the hydraulic

piston rod and insert connecting pin (2).

13. Thread the short threads of pump cylinder (12) into the

motor/pump block and tighten with a strap wrench.

14. Place o-ring (13) onto the top grove of pump cylinder (12).

15. Thread foot valve (16) onto pump cylinder (12), tighten with

a strap wrench, then back off to align the siphon hose.

Item

Part # Description Quantity

1 143-019 Retainer ring .........................................1

2 107-003 Connecting pin......................................1

3 106-015 O-ring, PTFE ........................................2

4 106-002 Packing set, leather/UHMPWPE/steel..2

5 106-005 Packing spring, SS ...............................1

6 108-021 Displacement rod ...................................1

7 106-001 Spring retainer ......................................1

8 106-116 Sleeve...................................................1

9 106-016 Packing spring, SS ...............................1

10 569-021 Ball, SS.................................................1

11 106-011 Piston seat ............................................1

12 108-940 Pump cylinder.......................................1

13 106-014 O-ring....................................................1

14 106-012 Ball cage, SS ........................................1

15 138-340 Ball, SS.................................................1

16 107-013 Foot valve assembly.............................1

Pump Service Kit, Major (P/N 108-501)

Item Part # Description Quantity

107-051 Pump Service Kit, Minor .......................1

6 108-021 Displacement rod..................................1

12 108-940 Pump cylinder.......................................1

Pump Service Kit, Minor (P/N 107-051)

Item Part # Description Quantity

1 143-019 Retainer ring .........................................1

3 106-015 O-ring, PTFE ........................................2

4 106-002 Packing set, leather/UHMWPE/steel ....2

8 106-116 Sleeve...................................................1

10 569-021 Ball, SS.................................................1

13 106-014 O-ring....................................................1

15 138-340 Ball, SS.................................................1

426-051 Loctite sealant.......................................1

753-024 PTFE tape sealant ...............................1

Motor

Pump

Block

NOTE: It is not necessary to over-tighten the foot valve.

O-ring seals perform sealing function without

excessive tightening. Full thread engagement is

sufficient. The foot valve may be rotated

backward up to 1/2 turn from full engagement for

convenient hose position.

For siphon hose attachment, it is critically

important that the threads of the siphon hose fit

snugly into the foot valve with the hose

assembly couplings PTFE taped and sealed to

prevent air leakage.

NOTE: Packings must be soaked in oil before

installation.

NOTE: Packings must be soaked in oil before

installation.

NOTE: Use PTFE tape on all threaded pipe connections.

Inlet Accessories

Bleed Line Assembly with Valve (P/N 840-212)

Item Part # Description Quantity

1 944-620 Bleed valve ...........................................1

2 103-117 Tube......................................................1

3 539-062 Hose assembly .....................................1

4 103-159 Bleed line assembly..............................1

Bleed Valve Assembly (P/N 944-620)

Item

Part # Description Quantity

1 944-005 Knob .....................................................1

2 860-721 Lock nut ................................................1

3 944-023 Valve stem ............................................1

4 ---------- Valve body ............................................1

5 944-004 O-ring, PTFE ........................................1

6 944-026 Valve stem stop ....................................1

7 569-170 Ball, T.C. ...............................................1

8 945-003 Copper gasket ......................................1

9 944-904 Valve seat .............................................1

Service Instructions

The 944-620 Series Bleed Valve has a tungsten carbide valve

seat and should not require frequent replacement. The tungsten

carbide ball, in normal service, will last a long time because it

rotates and wears evenly. If there is leakage, replace the ball.

Open the adjustment knob, to full counterclockwise position

before unthreading valve seat, from valve body. If the valve

stem is rotated inwardly with the ball removed, the PTFE o-

ring may require replacement. If there has been leakage

from the valve stem, the PTFE o-ring should be replaced

All non-moving threads must be assembled with Speeflo

Loctite Sealant (P/N 426-051).

CAUTION

NOTE: The valve stem stop must be unthreaded from the

valve stem with a socket screwdriver, then the

valve stem can be threaded out of the valve body.

CAUTION

Siphon Hose Assembly

103-828 103-827

Item

Part # Description Qty. Qty.

1 420-070 Hose ......................................1................1

2 103-679 Hose clamp............................2................2

3 103-575 Tube.......................................1

4 103-627 Rock catcher..........................1................1

5 194-761 Adapter ..................................1................1

6 103-119 Clip.........................................1................1

7 103-125 Spring ....................................1................1

Outlet Accessories

930 Outlet Manifold Filter Assembly with Check

Valve

930-514 930-515 930-516

Item

Part # Description Qty.

Qty.. Qty.

1 930-937 Filter cap assembly .......1 .............1.............1

2 930-020 Spring ............................1 .............1.............1

3 930-005 Filter element,

5 M, w/ball .....................1

930-006 Filter element,

50 M, w/ball ...................................1

930-007 Filter element,

100 M, w/ball ................................................1

4 920-006 Gasket, PTFE (thick).....1 .............1.............1

5 920-070 Gasket, PTFE (thin) ......1 .............1.............1

6 891-193 O-ring, PTFE.................1 .............1.............1

7 180-909 Seat, tungsten carbide ..1 .............1.............1

8 930-920 Filter body......................1 .............1.............1

9 193-331 Hex nipple......................* ..............* .............*

10 812-003 Hex nipple......................* ..............* .............*

11 227-033 Pipe plug........................* ..............* .............*

12 191-449 Hex nipple......................* ..............* .............*

*Order installation kit P/N 930-101.

Filter Service Kit (P/N 930-050)

Item Part # Description Quantity

2 930-020 Spring ...................................................1

4 920-006 Gasket, PTFE.......................................1

5 920-070 Gasket, PTFE.......................................1

6 891-193 O-Ring, PTFE.......................................1

Specifications

Maximum Working Pressure............5000 psi (345 bar)

Filter Area.........................................18 In

(116 cm

)

Outlet Ports......................................(1) 1/4" NPT(F) for bleed

valve

(1) 3/8" NPT(F) with 1/4

NPSM(M) hose connection

(1) 3/8" NPT(F) plugged for

additional gun hookup.

Wetted Parts ....................................Carbon steel with electroless

nickel and cadmium plating,

stainless steel, tungsten

carbide, PTFE

Operation

The 930 Series Outlet Manifold Filter has a built in spring actuated

check valve. It uses a replaceable filter element with a stainless

steel check ball permanently trapped inside the element. The

element is available in the following screen sizes:

Part #

Mesh Typical Applications

930-005 5 High viscosity materials

930-006 50* Conventional materials

930-007 100 Low viscosity materials

The filter cap has a long stem that acts as a spring guide and

controls ball travel within the filter element. The filter body has a

replaceable tungsten carbide seat which is secured by a PTFE o-

ring.

The incorporation of this spring loaded check valve into the filter

manifold greatly reduces hydraulic shock at stroke changeover

and reduces opportunity for hydraulic stalls. Always use the 930

Series Filter Element / Check Ball in this PowrLiner system. Do

not use 920 Series filter elements. Do not run the system

without a 930 Series filter element/check ball. When using heavy

high viscosity materials, use the 5-mesh filter element/check ball.

Cleaning

Clean filter regularly. Dirty or clogged filters can greatly reduce

filtering ability and cause a number of system problems including

poor spray patterns, clogged spray tips, etc.

To clean the filter, shutoff system and relieve all system pressure,

see the “Pressure Relief Procedure” in the Safety Warnings

section of this manual

Remove filter cap with spring guide (1) and spring (2). Pull filter

element with check ball (3) straight out of filter body (8).

Thoroughly clean inside filter body (8), filter element with check

ball (3), and filter cap with spring guide (1) with appropriate

solvent. Use care in handling parts as dirt, debris, scratches, or

nicks may prevent o-rings or gaskets from sealing.

The 930 Series Filter Elements filter from the inside out. Be

certain to clean the screen element thoroughly on the inside.

Soak in solvent to loosen hardened paint. etc. or replace.

Service

1. Inspect ball trapped inside filter element (3). If ball has

pressure cuts or scratches, replace filter element.

2. If ball is cut, remove PTFE o-ring (6) with an o-ring pick and

remove tungsten carbide seat (7). Check carbide seat for

nicks or grooves. If seat is nicked or grooved, replace.

3. Removal of the PTFE o-ring (6) for seat (7) inspection will

damage the o-ring and require replacement.

4. Remove the spring (2) from the filter cap (1). Measure the

length of the spring, uncompressed. If it measures less than

3/4" from end to end, replace. Push spring back onto spring

guide until it "snaps" in place.

5. Inspect the PTFE gaskets (4, 5) and o-ring for deformity,

nicks, cuts, etc. Replace as required.

Reassembly

After inspecting and cleaning all parts, reassemble the filter assembly.

1. Place tungsten carbide seat (7) in filter body, using care to

place the beveled side up.

2. Place PTFE o-ring (6) in groove on the outer diameter of the

tungsten carbide seat (7).

3. Place filter element/check ball (3) back in filter body (8).

4. Place spring (2) back onto spring guide in filter cap (1).

Push spring onto guide rod until it "snaps" in place.

5. Place thin PTFE gasket (5) onto step at top of the filter body (8).

6. Place thick PTFE gasket (4) onto top of the gasket (5).

7. Tighten filter cap (1) onto filter body (8). This will engage o-

ring (6) against tungsten carbide seat (7).

NOTE: The top and bottom of the filter element/check

ball are identical.

NOTE: The PTFE o-ring (6) and PTFE gaskets (4, 5) are

packaged in the Filter Service Kit (P/N 930-050).

NOTE: Inspect all parts thoroughly.

Second Gun Assembly Complete (P/N 759-038)

Item Part #

Description Quantity

1 756-029 Block clamp ..........................................1

2 424-288 Cable guide...........................................1

3 756-124 Extension support bracket....................1

4 814-002 Hex nipple ............................................1

5 203-516 Whip hose assembly ............................1

6 862-436 Screw, hex head...................................1

7 862-002 Lock washer .........................................1

8 424-226 Cable mounting clamp..........................1

9 424-224 Support arm..........................................1

10 756-034 Knob .....................................................1

11 424-201 Gun holder............................................1

12 858-002 Lock washer .........................................2

13 858-636 Screw, hex head...................................2

14 756-035 Clamp ...................................................1

15 858-912 Screw, shoulder....................................1

16 424-229 Grease fitting........................................1

17 424-248 Flanged bearing ...................................2

18 858-637 Screw....................................................1

19 858-601 Nut........................................................1

20 940-553 Ball valve..............................................1

21 227-006 Hex nipple ............................................1

22 424-216 Gun control cable assembly.................1

23 858-603 Nut........................................................2

24 860-936 Screw, shoulder....................................1

25 424-202 Actuator lever .......................................1

26 424-249 Sleeve bearing .....................................1

27 858-653 Screw, socket head ..............................1

28 520-100 Airless gun, SGX-20.............................1

29 641-517 Reversible tip, .017” .............................1

645-1904 Reversible tip, .019...............................1

Second Gun Installation

Before installing the second gun, follow the “Pressure Relief

Procedure” in the Cleanup section of this manual. Once you

have completed this procedure, unplug the power supply

cord. Failure to reduce pressure can result in serious injury.

1. Engage the first gun’s trigger lock.

2. Remove the trigger cable from the block of the first gun.

NOTE: The gun or guns can be installed on either side

of the cart and can face either forward or

backward.

Trigger Cable

WARNING

NOTE: The gun support beam must be removed to

install the second gun and hose. The sprayer

must be shut down before installation.

3. Remove the plastic plug from the main bar. Slide the

extension bar through the clamp upright and the main bar to

the desired position. Tighten the clamp knob to secure the

clamp upright and the extension bar.

4. Mount the gun holders as shown in the Cart Assembly

exploded view drawing in this section.

5. Locate the second gun outlet on the pump. Remove the

plug and screw in the second gun hose.

6. Insert the cable bushing into the guide plate. The first gun

cable and the second gun cable should be parallel.

7. Insert the hooked end of the cable into the lever plate.

Make sure it engages the plate.

8. Reconnect the trigger cables to the guns. Connect both

cables to the blocks.

NOTE: Once the second gun is in positio, the trigger

cables can be installed on both guns. Make sure

the trigger cable from the second gun is

disconnected before performing the next step.

NOTE: The main bar has a clearance hole for the clamp

knob to go through and tighten onthe extension

bar.

Main Bar

Clamp Upright

Extension

Bar

Clamp Knob

Remove plastic plug.

Tension Adjustment

To increase tension, loosen the screw in the cable tension clamp

block on the gun arm. Slide the block forward to increase the

gap between the lever and the point where the trigger touches

the gun arm.

To decrease tension, slide the block backwards. Make sure

there is about 1/32” to 1/16” gap between the trigger lever and

where the trigger touches the bar.

Before making any adjustments to the gun, always move the

gun’s trigger lock to its locked position and release the

trigger cable from the block by lifting the cable up and out

of the block. There will be a brief triggering of the gun when

you release the cable.

CAUTION

Check gap here

Cable Tension

Clamp Block

Line Pointer (P/N 424-620)

Item Part # Description Quantity

1 424-244 Clamping bolt........................................2

2 424-257 Clamp ...................................................1

Item

Part # Description Quantity

3 424-258 Guide....................................................1

4 424-268 Cap.......................................................1

Trigger Assembly

Item Part # Description Quantity

1 424-219 Mounting block .....................................1

2 856-744 Screw....................................................1

3 424-203 Trigger ..................................................1

4 424-218 Flanged bearing ...................................2

5 759-034 Pin ........................................................1

6 424-229 Grease fitting ........................................1

7 759-015 Clevis pin..............................................1

8 424-217 Lever plate............................................2

9 759-033 Knob .....................................................1

10 424-227 Spool ....................................................1

Trigger Selection

The handlebar on the right triggers the gun or guns. The

selector on the trigger must be set for the first gun, both guns, or

the second gun .

First Gun

The first gun position is with the

selector in the left position. Push

the lever toward the inside of the

frame until the pin engages the left

plate.

Dual Guns

The dual gun position is with the

selector in the center position.

Push the lever toward the center

position until the pin engages both

plates. The pin must engage both

plates.

Second Gun

The second gun position is with

the selector in the right position.

Push the lever away from the

inside of the frame until the pin

engages the right plate.

SAE O-Ring Fitting Installation

Steps 1 & 2:

Step 3:

Step 4:

Step 5:

Cautions:

Lubricate

Tighten nut

Recess

gap

No gap

Align

Hold

this part

stationay

Avoid screwing fitting in too far.

Avoid leaving fitting too far out.

Bent washer allows

for o-ring extrusion

O-ring cut on

thread

Accessories and Service Kits

These items may be purchased separately from your local

Speeflo distributor.

Part #

Description

930-005 Paint Filter Element, 5 Mesh

(for high viscosity materials)

930-006 Paint Filter Element, 50 Mesh

(for conventional materials)

930-007 Paint Filter Elements, 100 Mesh

(for low viscosity materials)

101-208 Grounding Clamp

101-212 Grounding Wire, 12 Gauge x 25'

700-925 Piston Lube

430-362 Coolflo™ Hydraulic Fluid, 1 Quart

430-361 Coolflo™ Hydraulic Fluid, 1 Gallon

930-050 Service Kit for Paint Filter

944-620 Service Kit for Bleed Valve

Athletic Field Marking Kit/Turf Kit

Item Part # Description Quantity

1 424-821 Axle assembly ......................................1

2 570-010 Cotter key .............................................2

3 870-404 Hex nut .................................................2

4 424-213 Wheel assembly ...................................2

Turf Kit Installation

1. To install the turf kit permanently:

a. Remove the lever assembly from the handle by removing

the screw and nut from the clamp that attaches the lever

assembly to the handle.

b. Disconnect the cable assembly form the lever actuator

assembly by removing the machine screw from the lever

actuator assembly.

c. Remove the cable locking nut located on the inside of the

gun bar bracket.

d. Slide the exposed cable through the slot in the gun bar

bracket and remove the entire cable assembly.

To install the turf kit temporarily:

a. Disconnect the nut and the socket head screw from the

the lever actuator assembly by removing the machine

screw from the lever actuator assembly.

b. Tie back the loose cable to the sprayer’s frame using

cable ties or t ape.

2. Remove the nut and the socket

head screw from the frame and

the lever actuator assembly. The

lever actuator will now hang from

the front wheel assembly by the

connecting ring.

3. With the sprayer tilted back,

remove the front wheel assembly

by removing the four nuts,

washers, and hex head screws

that secure it to the frame.

4. Bolt the turf kit assembly to the

frame using the four nuts,

washers, and hex head screws removed in the previous step.

Frame

Turf Kit

Assembly

1. Pull washer and o-

ring back as far as

possible.

2. Lubricate o-ring and

entrance port.

3. Screw fitting in until

washer pushes o-

ring into entrance

and sits flat against

port. (Do not

tighten! - only do this

step hand tight to

compress o-ring into

port!)

4. Back fitting out no

more than one

complete turn to

align as required.

5. Torque nut wrench

tight holding backup

on fitting. This

should expose a

recess gap behind

the nut which can

act as an indicator

that the fitting is

assembled correctly.

(This is a feature for

a specific version of

this fitting only -

which screws into

the cylinder head.

Other fittings, as the

ones which attach to

the hydraulic pump,

assemble the same

but may not have

the indicator.)

Notes

Titan Tool Inc. warrants all equipment manufactured by it and bearing its brand names to be free from defects in material and

workmanship at the time of sale by an authorized Speeflo distributor. Titan Tool Inc. will for a period of twelve months (twenty-four

months on selected air powered models) from the date of sale, repair or replace any part of the equipment proven defective. Repair

or replacement under this warranty shall be purchaser's sole remedy for breach of this warranty. Products furnished by but not

manufactured by Titan Tool Inc. (such as hose, motors, engines, hydraulic pumps, etc.) will carry only the warranty of the

manufacturer, if any. (TITAN TOOL INC. DOES NOT WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE FOR ACCESSORIES, MATERIALS, EQUIPMENT,

COMPONENTS AND PRODUCTS NOT MADE BY TITAN TOOL INC.)

This warranty shall not apply if the product has been subject to misuse, negligence, accident or tampering or has not been operated

or installed in accordance with Titan Tool Inc.'s recommendations. This warranty does not cover and Titan Tool Inc. shall not be liable

for any damage, wear or malfunction caused by improper or inadequate maintenance, abrasion, corrosion or substitution of

components, parts or hydraulic fluid not supplied by Titan Tool Inc. Titan Tool Inc. shall not be liable for the improper design,

manufacture, installation, operation or maintenance of accessories, components or materials not supplied by Titan Tool Inc. Titan Tool

Inc. shall not be liable for damage or wear caused by incompatibility with Titan Tool Inc. equipment of materials, equipment or

accessories not supplied by Titan Tool Inc.

This warranty applies only to the original purchaser and only when the equipment is installed, operated and maintained in accordance

with Titan Tool Inc.'s written recommendations or instructions. Purchaser must, with transportation prepaid, return the equipment

claimed to be defective to Titan Tool Inc. or to an authorized Warranty Service Center for verification of the claimed defect. If the

alleged defect is verified, Titan Tool Inc. will, at Titan Tool Inc.'s option, repair or replace any defective parts. The equipment will be

returned including prepayment of transportation charges to the original purchaser. If no defects in material and workmanship are

found, repairs will be made by Titan Tool Inc. at a reasonable charge. Charges may include the cost of parts, labor and freight.

No statement or recommendation made or assistance given by Titan Tool Inc. or its representatives to purchaser, lessee or user or its

representatives shall constitute a warranty by Titan Tool Inc. or a waiver or modification of any of the provisions hereof to create any

liability for Titan Tool Inc. No sample or model shall create an express warranty that the products shall conform to any sample or

model exhibited by Titan Tool Inc.

TITAN TOOL INC. DISCLAIMS TO THE FULL EXTENT PERMITTED BY LAW ALL WARRANTIES, EXPRESSED OR IMPLIED,

INCLUDING ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND ANY

NON CONTRACTUAL LIABILITIES INCLUDING PRODUCT LIABILITY BASED ON NEGLIGENCE OR STRICT LIABILITIES. Every

form of liability is expressly excluded and denied for direct, indirect, special or consequential damages or loss. This warranty shall be

in lieu of any other warranty expressed or implied. The terms of this warranty constitute purchaser's sole and exclusive remedy. In

no case shall Titan Tool Inc.'s liability exceed the amount of the purchase price. Any action for breach of warranty must be brought

within two (2) years of the date of sale.

United States Sales & Service

1-800-526-5362

Fax 1-800-528-4826

556 Commerce Street

Franklin Lakes, NJ 07417

Canadian Branch

1-800-565-8665

Fax 1-905-856-8496

200 Trowers Road, Unit 7B

Woodbridge, L4L 5Z8

International

1-201-405-7520

Fax 1-201-405-7449

556 Commerce Street

Franklin Lakes, NJ 07417 USA

www.titan-tools.com

Limited Warranty

Patents

These products are covered by one or more of the following U.S. patents:

5,947,381 5,749,528 5,660,332 5,425,506 4,611,758 4,508,268

Titan PowrLiner 5000 El manual del propietario

Marca: Titan

Modelo: PowrLiner 5000

Categoría: Rociador de pintura

Tipo: El manual del propietario

Este manual también es adecuado para

PowrLiner™ 5000

Descargar PDF

informe

En otros idiomas

français: Titan PowrLiner 5000 Le manuel du propriétaire
English: Titan PowrLiner 5000 Owner's manual

Titan PowrLiner 5000 El manual del propietario

Este manual también es adecuado para

Titan PowrLiner 5000 El manual del propietario

En otros idiomas

Documentos relacionados

Otros documentos