Titan PowrTwin™ 6900 XLT DI El manual del propietario
- Categoría
- Rociador de pintura
- Tipo
- El manual del propietario
Este manual también es adecuado para
Printed in the U.S.A.
0314 • © Titan Tool Inc. All Rights Reserved. Form No. 0528914C
NOTE: This manual contains important
warnings and instructions. Please
read and retain for reference.
Model Numbers:
Gas Bare 448-350
Gas Complete 448-355
Gas Complete w/ Heavy
Duty Bypass Valve 448-360
230V Electric Bare 448-365
230V Electric Complete 448-370
Do not use this equipment
before reading this manual!
Owner’s Manual
For professional use only
SPEEFLO
PowrTwin 6900XLT DI
Register your product online at:
www.titantool.com
Proper registration will serve as proof of purchase in the event your
original receipt becomes misplaced or lost.
Serial Number _ _ _ _ _ _ _ _ _ _
2 © Titan Tool Inc. All rights reserved.
Important Safety Information · Read all safety information before
operating the equipment. SAVE THESE INSTRUCTIONS.
This symbol indicates a hazardous situation,
which, if not not avoided could result in death or
serious injury.
To reduce the risks of fire or explosion, electrical
shock, and the injury to persons, read and
understand all instructions included in this manual.
Be familiar with the controls and the proper usage
of the equipment.
WARNING – To reduce the risk of fire or
explosion:
1. Do not spray ammable or combustible
materials near an open ame, pilot lights
or sources of ignition such as hot objects,
cigarettes, motors, electrical equipment and
electrical appliances. Avoid creating sparks
from connecting and disconnecting power cords.
2. For units intended for use with only water-based materials
— Do not spray or clean with ammable liquids. For use
with water-based liquids only.
3. For units intended for use with only water-based or mineral
spirit-type materials with a minimum ash point of 38ºC
(100ºF) — Do not spray or clean with liquids having a
ash point of less than 38ºC (100ºF). Flash point is the
temperature at which a uid can produce enough vapor to
ignite.
4. Paint or solvent owing through the equipment is able to
result in static electricity. Static electricity creates a risk of
re or explosion in the presence of paint or solvent fumes.
All parts of the spray system, including the pump, hose
assembly, spray gun and objects in and around the spray
area shall be properly grounded to protect against static
discharge and sparks. Use only conductive or grounded
high-pressure airless paint sprayer hoses specied by the
manufacturer.
5. Verify that all containers and collection systems are
grounded to prevent static discharge.
6. Connect to a grounded outlet and use grounded extension
cords (electric models only). Do not use a 3 to 2 adapter.
7. Do not use a paint or solvent containing halogenated
hydrocarbons. Such as chlorine, bleach mildewcide,
methylene chloride and trichloroethane. They are not
compatible with aluminum. Contact the coating supplier
about compatibility of material with aluminum.
8. Keep spray area well ventilated. Keep a good supply of
fresh air moving through the area to keep the air within the
spray area free from accumulation of ammable vapors.
Keep pump assembly in well ventilated area. Do not spray
pump assembly.
9. Do not smoke in the spray area.
10. Do not operate light switches, engines, or similar spark
producing products in the spray area.
11. Keep area clean and free of paint or solvent containers,
rags, and other ammable materials.
12. Know the contents of the paint and solvents being
sprayed. Read all Material Safety Data Sheets (MSDS)
and container labels provided with the paints and solvents.
Follow the paint and solvent manufacture’s safety
instructions.
13. Place pump at least 25 feet (7.62 meters) from the
spray object in a well ventilated area (add more hose if
necessary). Flammable vapors are often heavier than
air. Floor area must be extremely well ventilated. The
pump contains arcing parts that emit sparks and can ignite
vapors.
14. Plastic can cause static sparks. Never hang plastic to
enclose spray area. Do not use plastic drop cloths when
spraying ammable material.
15. Fire extinguisher equipment shall be present and working.
WARNING – To reduce the risk of skin
injection:
HAZARD:
Injection injury – A high pressure fluid stream produced by
this equipment can pierce the skin and underlying tissues,
leading to a serious injury and possible amputation. See a
physician immediately. DO NOT TREAT AN INJECTION AS A
SIMPLE CUT.
1. Do not aim the gun at, or spray any person or animal.
2. Keep hands and other body parts away from the
discharge. For example, do not try to stop leaks with any
part of the body.
3. Always use the nozzle tip guard. Do not spray without the
nozzle tip guard in place.
4. Only use a nozzle tip specied by the manufacturer.
5. Use caution when cleaning and changing nozzle tips. In
the case where the nozzle tip clogs while spraying,
ALWAYS lock gun trigger, shut pump off, and release
all pressure before servicing, cleaning tip or guard, or
changing tip. Pressure will not be released by turning off
the motor. The PRIME/SPRAY valve or pressure bleed
valve must be turned to their appropriate positions to
relieve system pressure. Refer to PRESSURE RELIEF
PROCEDURE described in the pump manual.
6. Do not leave the unit energized or under pressure while
unattended. When the unit is not in use, turn off the
unit and relieve the pressure in accordance with the
manufacturer’s instructions.
7. High-pressure spray is able to inject toxins into the body
and cause serious bodily injury. In the event that injection
occurs, seek medical attention immediately.
8. Check hoses and parts for signs of damage, a leak can
inject material into the skin. Inspect hose before each use.
Replace any damaged hoses or parts.
9. This system is capable of producing 3300 PSI / 22.8
MPa. Only use replacement parts or accessories that
are specied by the manufacturer and that are rated a
minimum of 3300 PSI. This includes spray tips, nozzle
guards, guns, extensions, ttings, and hose.
10. Always engage the trigger lock when not spraying. Verify
the trigger lock is functioning properly.
11. Verify that all connections are secure before operating the
unit.
12. Know how to stop the unit and bleed pressure quickly. Be
thoroughly familiar with the controls. Pressure will not be
released by turning off the motor. The PRIME/SPRAY
valve or pressure bleed valve must be turned to their
appropriate positions to relieve system pressure. Refer
to PRESSURE RELIEF PROCEDURE described in the
pump manual.
13. Always remove the spray tip before ushing or cleaning
the system.
© Titan Tool Inc. All rights reserved. 3
Important Safety Information · Read all safety information before
operating the equipment. SAVE THESE INSTRUCTIONS.
WARNING – To reduce the risk of injury:
1. Always wear appropriate gloves, eye protection, clothing
and a respirator or mask when painting. Hazardous
vapors – Paints, solvents, insecticides, and other materials
can be harmful if inhaled or come in contact with body.
Vapors can cause severe nausea, fainting or poisoning.
2. Do not operate or spray near children. Keep children
away from equipment at all times.
3. Do not overreach or stand on an unstable support. Keep
effective footing and balance at all times.
4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under the
inuence of drugs or alcohol.
6. Do not kink or over-bend the hose. Airless hose can
develop leaks from wear, kinking and abuse. A leak can
inject material into the skin.
7. Do not expose the hose to temperatures or pressures in
excess of those specied by manufacturer.
8. Do not use the hose as a strength member to pull or lift the
equipment.
9. Use lowest possible pressure to ush equipment.
10. Follow all appropriate local, state and national codes
governing ventilation, re prevention and operation.
11. The United States Government Safety Standards have
been adopted under the Occupational Safety and Health
Act (OSHA). These standards, particularly part 1910 of
the General Standards and part 1926 of the Construction
Standards should be consulted.
12. Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement
of couplings. Immediately replace hose if any of those
conditions exist. Never repair a paint hose. Replace with
a conductive high-pressure hose.
13. Do not spray outdoors on windy days.
14. Always unplug cord from outlet before working on
equipment (electric models only).
Grounding Instructions
Electric models must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This product is
equipped with a cord having a grounding wire with an appropriate
grounding plug. The plug must be plugged into an outlet that
is properly installed and grounded in accordance with all local
codes and ordinances.
WARNING — Improper installation of the grounding plug can
result in a risk of electric shock. If repair or replacement of the
cord or plug is necessary, do not connect the green grounding
wire to either at blade terminal. The wire with insulation having a
green outer surface with or without yellow stripes is the grounding
wire and must be connected to the grounding pin.
Check with a qualied electrician or serviceman if the grounding
instructions are not completely understood, or if you are in doubt
as to whether the product is properly grounded. Do not modify
the plug provided. If the plug will not t the outlet, have the
proper outlet installed by a qualied electrician.
Grounded Outlet
Grounding Pin
Cover for grounded outlet box
IMPORTANT: Use only a 3-wire extension cord that has
a 3-blade grounding plug and a 3-slot receptacle that will
accept the plug on the product. Make sure your extension
cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. A 12
gauge cord is recommended. If an extension cord is to be
used outdoors, it must be marked with the suffix W-A after
the cord type designation. For example, a designation of
SJTW-A would indicate that the cord would be appropriate
for outdoor use.
Gasoline Engine Safety
The engine exhaust from this unit contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
1. Gas engines are designed to give safe and dependable
service if operated according to instructions. Read and
understand the engine Owner’s Manual before operating
the engine. Failure to do so could result in personal injury
or equipment damage.
2. To prevent re hazards and to provide adequate
ventilation, keep the engine at least 1 meter (3 feet) away
from buildings and other equipment during operation. Do
not place ammable objects close to the engine.
3. Children and pets must be kept away from the area of
operation due to a possibility of burns from hot engine
components or injury from any equipment the engine may
be used to operate.
4. Know how to stop the engine quickly, and understand the
operation of all controls. Never permit anyone to operate
the engine without proper instructions.
5. Gasoline is extremely ammable and is explosive under
certain conditions.
6. Refuel in a well-ventilated area with the engine stopped.
Do not smoke or allow ames or sparks in the refueling
area or where gasoline is stored.
7. Do not overll the fuel tank. After refueling, make sure the
tank cap is closed properly and securely.
8. Be careful not to spill fuel when refueling. Fuel vapor or
spilled fuel may ignite. If any fuel is spilled, make sure the
area is dry before starting the engine.
9. Never run the engine in an enclosed or conned area.
Exhaust contains poisonous carbon monoxide gas;
exposure may cause loss of consciousness and may lead
to death.
10. The mufer becomes very hot during operation and
remains hot for a while after stopping the engine. Be
careful not to touch the mufer while it is hot. To avoid
severe burns or re hazards, let the engine cool before
transporting it or storing it indoors.
11. Never ship/transport unit with gasoline in the tank.
DO NOT use this equipment to spray water or acid.
IMPORTANT: Do not lift by cart handle when loading or
unloading.
4 © Titan Tool Inc. All rights reserved.
Table of Contents
Safety Precautions ................................................................ 2-3
Grounding Instructions ........................................................ 3
Gasoline Engine Safety ....................................................... 3
Specications ........................................................................... 4
Introduction ............................................................................... 5
Operation ................................................................................... 5
Fueling................................................................................. 5
Operating the Swing Cart .................................................... 6
Setup ................................................................................... 6
Preparing to Paint................................................................ 8
Painting ............................................................................... 8
Pressure Relief Procedure .................................................. 9
Cleanup ..................................................................................... 9
Cleaning a Clogged Tip ..................................................... 10
Maintenance ............................................................................ 10
Daily Maintenance ............................................................. 10
Maintaining the Filter Assembly ........................................ 11
Maintaining the Hydraulic System ..................................... 11
Maintaining the Fluid Section ............................................ 11
Basic Engine Maintenance (gas engine) ........................... 12
Replacing the Motor Brushes (electric motor) ................... 12
Troubleshooting ..................................................................... 13
Airless Gun ........................................................................ 13
Fluid Section...................................................................... 13
Hydraulic Motor ................................................................. 14
Spray Patterns................................................................... 15
Parts Lists and Service Instructions .................................... 20
Main Assembly .................................................................. 20
Cart Assembly ................................................................... 21
Belt Guard Assembly......................................................... 21
Hydraulic Motor ................................................................. 22
Fluid Section...................................................................... 24
Hydraulic System .............................................................. 26
Gas Convertokit................................................................. 27
DC— Electric Convertokit.................................................. 27
Electric Convertokit, 230V ................................................. 28
Bleed Valve Assembly....................................................... 28
Filter Assembly .................................................................. 29
Heavy Duty Outlet Assembly (optional)............................. 29
Heavy Duty Bleed Valve Assembly (optional) ................... 29
Gun Manifold Assemblies (optional).................................. 30
SAE O-Ring Fitting Installation .......................................... 31
Accessories and Service Kits ............................................... 31
Airless Tip Selection .......................................................... 31
Warranty .................................................................................. 32
Specications
Gas Sprayer
Gallons per minute (GPM) ............. 2.15 (8.14 LPM)
Cycle rate per gallon...................... 51 (14.5 cycles/liter)
Maximum tip sizes ......................... 1 gun = .048”
2 guns = .033”
3 guns = .023”
4 guns = .019”
Maximum pressure ........................ 3300 PSI (22.8 MPa)
Power ......................................... Honda 4.8 HP, 4-stroke,
single cylinder, overhead
valve engine w/oil alert
Fuel capacity ................................. 0.83 US gallons
(approx. 3.5 hours run time)
Halogenated solvent compatible ... Yes
Weight ......................................... 149 lbs. (67.6 kg.)
Inlet paint lter ............................... 10 mesh “Rock Catcher”
Outlet paint lter ............................ 50 mesh, 18 in.
2
Pump inlet...................................... 1” NPT(F)
Pump outlet ................................... 1/2” NPT(F) to paint lter
Paint lter hose connections.......... 3/8” NPS(M)
3/8” NPT(F) (plugged)
1/4” NPT (plugged)
Dimensions .................................... 43” L (109 cm) x
26” W (66 cm) x
35” H (89 cm)
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, Teon, thiokol
impregnated leather, ultra high molecular weight polyethylene.
Electric Sprayer
Gallons per minute (GPM) ............. 1.25 (4.7 LPM)
Cycle rate per gallon...................... 55 (14.5 cycles/liter)
Maximum tip sizes ......................... 1 gun = .036”
2 guns = .026”
3 guns = .019”
Maximum pressure ........................ 3300 psi (22.8 MPa)
Power ......................................... 2 HP DC Motor, 115V 15.5A,
overload protected
Halogenated solvent compatible ... Yes
Weight ......................................... 165 lbs. (74.8 kg.)
Inlet paint lter ............................... 10 mesh “Rock Catcher”
Outlet paint lter ............................ 50 mesh, 18 in.
2
Pump inlet...................................... 1” NPT(F)
Pump outlet ................................... 1/2” NPT(F) to paint lter
Paint lter hose connections.......... 3/8” NPS(M)
3/8” NPT(F) (plugged)
1/4” NPT (plugged)
Dimensions .................................... 43” L (109 cm) x
26” W (66 cm) x
35” H (89 cm)
Fluid section wetted parts:
Electroless nickel plated ductile iron, electroless nickel plated
carbon steel, stainless steel, tungsten carbide, Teon, thiokol
impregnated leather, ultra high molecular weight polyethylene.
© Titan Tool Inc. All rights reserved. 5
Introduction
Congratulations on having selected the nest airless sprayer
available in the world. Titan piston pumps are tireless
workhorses — so tough they are virtually indestructible, even
under the most severe service. Titan designs and builds
equipment with superior quality and reliability. Equipment that
will last for years with minimal maintenance and downtime. This
equipment will make you money year after year. We thank you
for your purchase and welcome you to our large and growing
family of Titan users.
The unique ability of this PowrTwin to operate with either gas or
electric power provides you with the exibility to work indoors or
outside where no electricity is available.
Hydraulic drive makes possible the longest stroke and slowest
cycling pumps in the industry, which translates into low
maintenance and longer life. Electric sprayers operate quietly
with no motor starting and stopping.
Motor/Pump
Assembly
Outlet Fitting
Pressure Control
Knob
Hydraulic
Fluid Cap/
Dipstick
Gas T
ank
Filter
Bleed Hose
Hydraulic
Shut-Off
Valve
Operation
Fueling (gas engine)
Gasoline is extremely flammable and is explosive
under certain conditions.
• ALWAYS turn the engine off before refueling.
• Refuel in a well-ventilated area.
• Do not smoke or allow ames or sparks in the refueling
area or where gasoline is stored.
• Do not overll the fuel tank. After refueling, make sure the
tank cap is closed properly and securely.
• Be careful not to spill fuel when refueling. Spilled fuel or
fuel vapor may ignite. If any fuel is spilled, make sure the
area is dry before starting the engine.
• Avoid repeated or prolonged contact with skin or breathing
of vapor.
• Keep out of the reach of children.
Fuel Specications
• Use automotive gasoline that has a pump octane number
of 86 or higher, or that has a research octane number of
91 or higher. Use of a lower octane gasoline can cause
persistent “pinging” or heavy “spark knock” (a metallic
rapping noise) which, if severe, can lead to engine
damage.
NOTE: If “spark knock” or “pinging” occurs at a steady
engine speed under normal load, change brands
of gasoline. If spark knock or pinging persists,
consult an authorized dealer of the engine
manufacturer. Failure to do so is considered
misuse, and damage caused by misuse is not
covered by the engine manufacturer’s limited
warranty.
Occasionally you may experience light spark
knock while operating under heavy loads. This
is no cause for concern, it simply means your
engine is operating efciently.
• Unleaded fuel produces fewer engine and spark plug
deposits and extends the life of the exhaust system
components.
• Never use stale or contaminated gasoline or an oil/
gasoline mixture. Avoid getting dirt, dust, or water in the
fuel tank.
Gasolines Containing Alcohol
If you decide to use a gasoline containing alcohol (gasohol), be
sure its octane rating is at least as high as that recommended
by the engine manufacturer. There are two types of “gasohol”:
one containing ethanol, and the other containing methanol. Do
not use gasohol that contains more than 10% ethanol. Do not
use gasoline containing methanol (methyl or wood alcohol)
that does not also contain co-solvents and corrosion inhibitors
for methanol. Never use gasoline containing more than 5%
methanol, even if it has co-solvents and corrosion inhibitors.
NOTE: Fuel system damage or engine performance
problems resulting from the use of fuels that
contain alcohol is not covered under the
warranty. The engine manufacturer cannot
endorse the use of fuels containing methanol
since evidence of their suitability is incomplete at
this time.
Before buying gasoline from an unfamiliar
station, try to nd out if the gasoline contains
alcohol. If it does, conrm the type and
percentage of alcohol used. If you notice any
undesirable operating characteristics while using
a gasoline that contains alcohol, or one that you
think contains alcohol, switch to a gasoline that
you know does not contain alcohol.
6 © Titan Tool Inc. All rights reserved.
Operating the Swing Cart
Use caution when operating the swing cart. Keep
fingers and feet clear of moving parts.
The swing cart allows the motor/pump assembly to be rotated
between two positions.
Position #1: Working Position
The vertical position of the motor/pump assembly is the working
position. This position allows complete submersion of the siphon
tube on the uid section into a paint bucket. The maximum
height paint bucket that can be used is 28 1/8” (71.4 cm).
Position #2: Transporting Position
The horizontal position of the motor/pump assembly is the
transporting position. This position allows easy removal of the
paint bucket and a sprayer height of 30” (76.2 cm) for ease of
transportation.
Use the following procedure to change the position of the motor/
pump assembly.
1. Holding the handle grip with one hand, pull the locking
pin out of the locking hole on the cart with the other hand.
This allows the motor/pump assembly mounted on the
swing cart frame to move from one position to the other.
2. Let go of the locking pin once it is free of the locking hole.
3. Move the motor/pump assembly to the desired position.
The locking pin is spring loaded and will automatically
engage the locking hole on the swing cart at the new
position.
Setup
Read, understand, and follow all warnings before
starting or operating this sprayer.
1. Make sure the bleed hose is threaded into the bleed valve.
It has factory installed Teon tape on the tting and should
be tightened wrench tight.
Bleed V
alve
Filter
Bleed Hose
2. Attach a minimum of 50’ of nylon airless spray hose to the
sprayer. Do not use Teon tape or thread sealant on the
spray hose connection.
3. Attach an airless spray gun to the spray hose. Do not
attach the tip to the spray gun yet. Remove the tip if it is
already attached.
a. To use two guns, remove the plug from the second gun
outlet on the lter assembly. Connect a hose and gun
to the outlet.
Multiple Gun
Manifold
NOTE: The gas sprayer is
engineered to handle up to 4
guns with .019” tips and the
electric sprayer is engineered
to handle up to 3 guns with
.019” tips. For multiple gun
operation, connect a multiple
gun manifold to the single
gun outlet. Connect a hose
and gun to each outlet. Make
sure the second gun outlet
remains plugged.
4. Fill the oil cup 1/2 full with Titan Piston
Lube (P/N 314-480) supplied by the
factory. This extends packing life.
5. Check the hydraulic uid level daily before starting the
sprayer. The hydraulic uid level should be at the “Full”
mark on the dipstick. Refer to the Maintenance section of
this manual for hydraulic system maintenance instructions.
IMPORTANT: Use of Titan’s Coolflo™ Hydraulic Fluid
is mandatory in the hydraulic system. Do not use any
other hydraulic fluid. Use of any other hydraulic fluid may
seriously damage the hydraulic system and will void the
warranty.
6. For gas models, check the engine oil level daily before
starting the sprayer. The gasoline engine oil level is
determined by the engine manufacturer. Refer to the
engine manufacturer’s service manual supplied with this
sprayer.
7. For electric models, use a 20 amp service outlet. Always
locate the electric model within 10 to 15 feet of the service
outlet. Use a short electric cable and a long paint hose.
Any extension cord will create some voltage drop. If an
extension cord is necessary, use only a grounded 3-wire
#12 gauge extension cord.
© Titan Tool Inc. All rights reserved. 7
NOTE: If the sprayer is being operated in an area that is
overloaded by other appliances or low voltage
conditions, it is important to start the sprayer
“unloaded.” Tip the electric motor forward so
that the belt is loosened and the motor starts
without full load. This reduces the amperage
draw on starting and may avoid tripping the
circuit breaker.
8. Make sure the sprayer is grounded. All sprayers are
equipped with a grounding lug. A grounding cable (not
supplied) should be used to connect the sprayer to a true
earth ground. Check your local electrical regulations for
detailed grounding instructions. See the Accessories
and Service Kits section near the back of this manual for
grounding cable ordering information.
Proper grounding is important. This applies to
both gas and electric powered models. The
passage of some materials through the nylon fluid
hose will build up a static electric charge, which if
discharged, could ignite solvent vapors present
and create an explosion.
9. Strain all paints with a nylon strainer to ensure trouble free
operation and freedom from frequent cleaning of the inlet
screen and gun lter.
10 Make sure the spray area is well ventilated to prevent
hazardous operation with volatile solvents or exhaust
fumes.
If lacquer or other flammable materials are to be
sprayed, ALWAYS locate the sprayer outside the
immediate spraying area. Failure to do so may
cause an explosion.
11. Locate the unit outside the immediate spraying area to
avoid clogged air intake of the engine or electric motor
with overspray.
Preparing a new sprayer
If this sprayer is new, it is shipped with test uid in the uid
section to prevent corrosion during shipment and storage. This
uid must be thoroughly cleaned out of the system with mineral
spirits before you begin spraying.
IMPORTANT: Always keep the trigger lock on the spray gun
in the locked position while preparing the system.
1. Place the siphon tube into a container of mineral spirits.
2. Place the bleed hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure
control knob fully counterclockwise.
Hydraulic Shut-of
f
Valve (in open
position)
Pressure Control
Knob
Bleed Valve
4. Open the hydraulic shut-off valve located on the hydraulic
pressure hose. The handle should be in line with the
hose.
5. Open the bleed valve by rotating the bleed valve handle
fully counterclockwise.
6. Start the engine or turn on the electric motor.
Fuel Valve
Lever
Choke Lever
Engine
Switch
Throttle
Lever
Starter Rope
a. To start the gas
engine,
• move the fuel valve
lever to the open
position,
• move the throttle
lever to its middle
point,
• move the choke lever
to the closed position
for a cold engine or
to the open position
for a warm engine,
• turn the engine switch to the ON position, and
• pull the starter rope briskly until the engine starts.
b. To start the electric motor, move the ON/OFF switch to
the ON position.
7. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and solvent ows freely from the bleed
hose.
8. Allow the sprayer to run for 15–30 seconds to ush the
test uid out through the bleed hose and into the waste
container.
9. Turn off the sprayer.
a. To turn off the gas engine,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the throttle lever to the slow position, and
• turn the engine switch to the OFF position.
b. To turn off the electric motor,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the ON/OFF switch to the OFF position.
8 © Titan Tool Inc. All rights reserved.
Preparing to Paint
Before painting, it is important to make sure that the uid in the
system is compatible with the paint that is going to be used.
NOTE: Incompatible uids and paint may cause the
valves to become stuck closed, which would
require disassembly and cleaning of the
sprayer’s uid section.
IMPORTANT: Always keep the trigger lock on the spray gun
in the locked position while preparing the system.
1. Place the siphon hose into a container of the appropriate
solvent.
NOTE: If you are spraying a water-based latex, ush with
warm, clean water. If you are using any other
material, check with the material manufacturer for
a compatible solvent.
2. Place the bleed hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure
control knob fully counterclockwise.
4. Open the hydraulic shut-off valve located on the hydraulic
pressure hose. The handle should be in line with the
hose.
5. Open the bleed valve by rotating the bleed valve handle
fully counterclockwise.
6. Start the engine or turn on the electric motor.
a. To start the gas engine,
• move the fuel valve lever to the open position,
• move the throttle lever to its middle point,
• move the choke lever to the closed position for a cold
engine or to the open position for a warm engine,
• turn the engine switch to the ON position, and
• pull the starter rope briskly until the engine starts.
b. To start the electric motor, move the ON/OFF switch to
the ON position.
7. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and solvent ows freely from the bleed
hose.
8. Allow the sprayer to run for 15–30 seconds to ush the
test uid out through the bleed hose and into the waste
container.
9. Turn off the sprayer.
a. To turn off the gas engine,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the throttle lever to the slow position, and
• turn the engine switch to the OFF position.
b. To turn off the electric motor,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the ON/OFF switch to the OFF position.
NOTE: Make sure that the spray gun does not have a tip
or tip guard installed.
10. Close the bleed valve by rotating the bleed valve handle
fully clockwise.
11. Start the engine or turn on the electric motor.
12. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure.
13. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
14. Trigger the gun into the metal waste container until the old
solvent is gone and fresh solvent is coming out of the gun.
Trigger lock in
locked position.
15. Lock the gun by turning the gun trigger
lock to the locked position.
16. Set down the gun and increase the
pressure by turning the pressure control
knob slowly clockwise.
17. Check the entire system for leaks. If
leaks occur, follow the “Pressure Relief
Procedure” in this manual before
tightening any ttings or hoses.
18. Follow the “Pressure Relief Procedure” in this manual
before changing from solvent to paint.
Be sure to follow the pressure relief procedure
when shutting down the sprayer for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray tips, or
preparing for cleanup.
Painting
1. Place the siphon tube into a container of paint.
2. Place the bleed hose into a metal waste container.
3. Set the pressure to minimum by turning the pressure
control knob fully counterclockwise.
Hydraulic Shut-of
f
Valve (in open
position)
Pressure Control
Knob
Bleed Valve
4. Open the hydraulic shut-off valve located on the hydraulic
pressure hose. The handle should be in line with the
hose.
5. Open the bleed valve by rotating the bleed valve handle
fully counterclockwise.
6. Start the engine or turn on the electric motor.
a. To start the gas engine,
Fuel V
alve
Lever
Choke Lever
Engine
Switch
Throttle
Lever
Starter Rope
• move the fuel valve
lever to the open
position,
• move the throttle lever
to its middle point,
• move the choke lever
to the closed position
for a cold engine or to
the open position for
a warm engine,
• turn the engine switch
to the ON position,
and
• pull the starter rope briskly until the engine starts.
b. To start the electric motor, move the ON/OFF switch to
the ON position.
© Titan Tool Inc. All rights reserved. 9
7. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure until the sprayer
cycles evenly and paint ows freely from the bleed hose.
8. Turn off the sprayer.
a. To turn off the gas engine,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the throttle lever to the slow position, and
• turn the engine switch to the OFF position.
b. To turn off the electric motor,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the ON/OFF switch to the OFF position.
9. Remove the bleed hose from the waste container and
place it into the container of paint.
10. Close the bleed valve by rotating the bleed valve handle
fully clockwise.
11. Start the engine or turn on the electric motor.
12. Turn the pressure control knob clockwise approximately
1/3 of the way down to increase pressure.
13. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
14. Trigger the gun into the metal waste container until all air
and solvent is ushed from the spray hose and paint is
owing freely. from the gun.
Trigger lock in
locked position.
1 5. Lock the gun by turning the gun trigger
lock to the locked position.
16. Turn off the sprayer.
17. Attach tip guard and tip to the gun as
instructed by the tip guard or tip manuals.
POSSIBLE INJECTION HAZARD. Do not spray
without the tip guard in place. Never trigger the
gun unless the tip is in either the spray or the
unclog position. Always engage the gun trigger
lock before removing, replacing or cleaning tip.
18. Start the engine or turn on the electric motor.
19. Increase the pressure by turning the pressure control knob
slowly clockwise and test the spray pattern on a piece
of cardboard. Adjust the pressure control knob until the
spray from the gun is completely atomized.
NOTE: Turning the pressure up higher then needed to
atomize the paint will cause premature tip wear
and additional overspray.
Pressure Relief Procedure
Be sure to follow the Pressure Relief Procedure
when shutting the unit down for any purpose,
including servicing or adjusting any part of the
spray system, changing or cleaning spray nozzles,
or preparing for cleanup.
Trigger lock in
locked position.
1. Lock the gun by turning the gun trigger
lock to the locked position.
2. Turn off the sprayer.
a. To turn off the gas engine,
• set the pressure to minimum by
turning the pressure control knob fully
counterclockwise,
• move the throttle lever to the slow
position, and
• turn the engine switch to the OFF position.
b. To turn off the electric motor,
• set the pressure to minimum by turning the pressure
control knob fully counterclockwise,
• move the ON/OFF switch to the OFF position.
3. Close the hydraulic shut-off valve on the hydraulic
pressure hose.
4. Unlock the gun by turning the gun trigger lock to the
unlocked position.
5. Hold the metal part of the gun rmly to the
side of a metal waste container to ground
the gun and avoid a build up of static
electricity.
6. Trigger the gun to remove any pressure
that may still be in the hose.
7. Lock the gun by turning the gun trigger lock to the locked
position.
8. Place the bleed hose into the metal waste container.
9. Open the bleed valve by rotating the bleed valve handle
fully counterclockwise.
Cleanup
Special cleanup instructions for use with
flammable solvents:
• Always ush spray gun preferably outside and at least one
hose length from spray pump.
• If collecting ushed solvents in a one gallon metal
container, place it into an empty ve gallon container, then
ush solvents.
• Area must be free of ammable vapors.
• Follow all cleanup instructions.
IMPORTANT: The sprayer, hose, and gun should be cleaned
thoroughly after daily use. Failure to do so permits material
to build up, seriously affecting the performance of the unit.
Always spray at minimum pressure with the gun
nozzle tip removed when using mineral spirits or
any other solvent to clean the sprayer, hose, or
gun. Static electricity buildup may result in a fire
or explosion in the presence of flammable vapors.
1. Follow the “Pressure Relief Procedure” found in the
Operation section of this manual.
2. Remove the gun tip and tip guard and clean with a brush
using the appropriate solvent.
3. Place the siphon tube into a container of the appropriate
solvent.
IMPORTANT: Use only compatible solvents when cleaning
out oil based enamels, lacquers, coal tar, and epoxies.
Check with the fluid manufacturer for the recommended
solvent.
10 © Titan Tool Inc. All rights reserved.
4. Place the bleed hose into a metal waste container.
5. Set the pressure to minimum by turning the pressure
control knob fully counterclockwise.
Hydraulic Shut-of
f
Valve (in open
position)
Pressure Control
Knob
Bleed Valve
6. Open the hydraulic shut-off valve located on the hydraulic
pressure hose. The handle should be in line with the
hose.
7. Open the bleed valve by rotating the bleed valve handle
fully counterclockwise.
8. Start the engine or turn on the electric motor.
9. Allow the solvent to circulate through the sprayer and
ush the paint out of the bleed hose into the metal waste
container.
10. Turn off the sprayer.
11. Close the bleed valve by rotating the bleed valve handle
fully clockwise.
12. Start the engine or turn on the electric motor.
Ground the gun by holding it
against the edge of the metal
container while flushing. Failure to
do so may lead to a static electric
discharge, which may cause a fire.
13. Trigger the gun into the metal waste container until the
paint is ushed out of the hose and solvent is coming out
of the gun.
14. Continue to trigger the spray gun into the waste container
until the solvent coming out of the gun is clean.
NOTE: For long-term or cold weather storage, pump
mineral sprits through the entire system.
15. Follow the “Pressure Relief Procedure” found in the
Operation section of this manual.
16. Store the sprayer in a clean, dry area.
IMPORTANT: Do not store the unit under pressure.
Cleaning a Clogged Tip
1. Follow the “Pressure Relief Procedure” in the Operation
section of this manual.
2. If the tip clogs, rotate the tip handle 180° until the arrow on
the handle is facing the opposite of the spray direction and
the handle clicks in the reverse position.
3. Trigger the gun once so that the pressure can blow the
clog out. NEVER use the tip in the reverse position for
more than ONE trigger pull at a time. This procedure can
be repeated until the tip is free of clogging.
The flow from the spray tip is at very high pressure.
Contact with any body part may be dangerous. Do
not place finger on gun outlet. Do not point the
gun at any person. Never operate the spray gun
without the proper tip guard.
Maintenance
Before proceeding, follow the Pressure Relief
Procedure outlined previously in this manual.
Additionally, follow all other warnings to reduce
the risk of an injection injury, injury from moving
parts or electric shock. Always unplug the sprayer
before servicing!
Daily Maintenance
Two daily procedures are required for routine operator
maintenance on this sprayer:
1. Lubricating the upper packings.
2. Cleaning the rock catcher.
Lubricating the Upper Packings
Packing Oil
Cup
1. Clean out the paint that has seeped
past the upper packings into the
packing oil cup above the uid section.
2. Fill the packing oil cup 1/2 full with
Piston Lube (P/N 314-480) supplied by
the factory. This will extend packing
life.
NOTE: Do not over-ll the oil cup so
that it overows and drips
into the paint.
Cleaning the Inlet Screen
Siphon
Tube
Inlet
Screen
1. Loosen and remove the inlet screen
from the siphon tube.
2. Clean thoroughly with the
appropriate solvent.
© Titan Tool Inc. All rights reserved. 11
Maintaining the Filter Assembly
Clean the lter regularly. Dirty or clogged lters can greatly
reduce ltering ability and cause a number of system problems
including poor spray patterns, clogged spray tips, etc.
Cleaning
To clean the lter, perform the following procedure.
1. Follow the “Pressure Relief Procedure” found in the
Operation section of this manual.
Filter Cap
Assembly
Filter
Element
w/Ball
Teflon Gasket
(thick)
Teflon Gasket
(thin)
Teflon O-ring
Carbide Seat
Filter Body
Spring
2. Remove the lter cap assembly
and spring.
3. Pull the lter element with ball
straight out of the lter body.
4. Clean inside the lter body, lter
element with ball, and lter cap
assembly using the appropriate
solvent.
NOTE: Use care in handling
parts as dirt, debris,
scratches, or nicks
may prevent o-rings or
gaskets from sealing.
This lter element lters
from the inside out. Be
sure to clean the lter
element thoroughly
on the inside. Soak
in solvent to loosen
hardened paint or
replace.
Inspection
Inspect all parts of the lter assembly before reassembly.
1. Inspect the ball inside the lter element. If the ball has
pressure cuts or scratches, replace the lter element.
a. If the ball is cut, remove the Teon o-ring using an
o-ring pick and remove the carbide seat.
b. Check the seat for nicks or grooves. If the seat is
damaged, replace.
NOTE: Removal of the Teon o-ring will damage the
o-ring and require replacement.
2. Remove the spring from the spring guide on the lter cap.
a. Measure the length of the spring uncompressed. If it
measures less the 3/4” from end to end, replace.
b. Push the spring back onto the spring guide until it
“snaps” back into position.
3. Inspect the two Teon gaskets and the Teon o-ring for
deformity, nicks, or cuts. Replace, if needed.
NOTE: The Teon gaskets, Teon o-ring, and spring are
packaged in Filter Service Kit P/N 930-050.
Reassembly
After cleaning and inspecting all parts, reassemble the lter.
1. Place the carbide seat into the lter body. Make sure the
beveled side of the seat is facing up.
2. Place the Teon o-ring into the groove on the outer
diameter of the carbide seat.
3. Place the lter element with ball into the lter body.
NOTE: The top and bottom of the lter element with ball
are identical.
4. Push the spring back onto the spring guide of the lter cap
until it “snaps” back into position, if not already done.
5. Place the thin Teon gasket onto the step at the top of the
lter body.
6. Place the thick Teon gasket onto the top of the thin
gasket.
7. Tighten the lter cap assembly onto the lter body.
Maintaining the Hydraulic System
IMPORTANT: Use of Titan’s Coolflo™ Hydraulic Fluid is
mandatory in the PowrTwin hydraulic system. Do not use
any other hydraulic fluid. Use of any other hydraulic fluid
may seriously damage the hydraulic system and will void
the warranty.
1. Check the hydraulic uid daily. It should be at the
“Full” mark on the dipstick. If it is low, add only Titan
Coolo™ Hydraulic Fluid (P/N 430-361). Never add or
change hydraulic uid except in a clean, dust-free area.
Contamination of the hydraulic uid will shorten hydraulic
pump life and may void warranty.
"Full" Mark
Hydraulic Fluid
Cap/Dipstick
Hydraulic
Filter
2. Change the hydraulic uid every twelve months. Drain
the old uid from the tank and ll with 4 quarts of Titan
Coolo™ Hydraulic Fluid. Start the sprayer at just enough
pressure to operate the uid section. Run the sprayer at
this low pressure for at least 5 minutes. This removes
air from the system. Check the uid level after this
procedure. Do not over-ll.
NOTE: When replacing the hydraulic lter during a uid
change, it may be necessary to add up to one
additional quart of hydraulic uid.
3. The hydraulic system has an external, replaceable
hydraulic lter. Change the lter every twelve months.
4. The hydraulic pump should not be serviced in the eld.
If service on the hydraulic pump is required, it must be
returned to Titan.
Maintaining the Fluid Section
If the sprayer is going to be out of service for an extended period
of time, it is recommended that following cleanup a kerosene and
oil mixture be introduced as a preservative. Packings may tend
to dry out from lack of use. This is particularly true of the upper
packing set for which upper packing lubricant Piston Lube (P/N
314-480) is recommended in normal usage.
If the sprayer has been out of service for an extended period of
time, it may be necessary to prime the pump with solvent. It is
extremely important that the threads on the siphon tube/hose
coupling are properly sealed. Any air leakage will produce erratic
operation of the sprayer and may damage the system. The up
and the down strokes should be approximately equal in time (one
should not be faster than the other). A fast up or down stroke
may indicate air in the system or malfunctioning valve or seats
(see the Troubleshooting section).
12 © Titan Tool Inc. All rights reserved.
Basic Engine Maintenance (gas engine)
• For detailed engine maintenance and technical
specications refer to the separate gasoline engine
manual.
• All service to the engine should be performed by a dealer
authorized by the engine manufacturer. To locate a dealer
in your area, look in the Yellow Pages of your telephone
directory under Gasoline Engines, Garden & Lawn
Equipment & Supplies, Lawn Mowers, etc.
• The gas engine is warranted exclusively by the engine
manufacturer.
• Use a premium quality motor oil certied to meet or
exceed U.S. Automotive requirement SG.or SF. SAE
10W30 is recommended for general all temperature use.
Other viscosities may be required in other climates.
• Use only a (NGK) BP6ES or BPR6E spark plug. Gap the
plug to 0.028 to 0.031 In. (0.7 to 0.8 mm) Always use a
spark plug wrench.
Daily
1. Check engine oil level, and ll as necessary.
2. Check gasoline level, and ll as necessary.
Always follow the fueling procedure outlined earlier
in this manual.
First 20 Hours
1. Change engine oil.
Every 100 Hours
1. Change engine oil.
2. Clean the sediment cup.
3. Clean and re-gap the spark plug.
4. Clean the spark arrestor.
Weekly
1. Remove the air lter cover and clean the element. In
very dusty environments, check the lter daily. Replace
the element as needed. Replacement elements can be
purchased from your local engine dealer.
Engine Operation and Service
1. Clean and oil air lter pad on gasoline engine every 25
hours or once weekly. Do not permit the air intake screen
around the y wheel of the gas engine to load up with
paint or trash. Clean it regularly. The service life and
efciency of the gas engine model depends upon keeping
the gasoline engine running properly. Change the oil
in the engine every 100 hours. Failure to observe this
may result in engine overheating. Consult the engine
manufacturer’s service manual provided.
2. To conserve fuel, service life, and efciency of the sprayer,
always operate the gasoline engine at the lowest RPM
at which it runs smoothly without laboring and delivers
the amount required for the particular painting operation.
Higher RPM does not produce higher working pressure.
The gasoline engine is connected to the hydraulic pump
by a pulley combination designed to produce full paint
delivery at maximum RPM.
3. The warranty on gasoline engines or electric motors is
limited to the original manufacturer.
Replacing the Motor Brushes (electric motor)
Perform this procedure using Motor Brush Kit P/N 978-050. The
kit consists of two brushes, two springs, and two clips.
NOTE: Brushes should be replaced when they are worn
to less than 1/2 inch. Check and replace both
brushes at the same time.
1. Remove both inspection covers on the motor.
Inspection
Cover
2. Push in the spring clip to unhook it, then pull it out..
T
erminal Screw
Spring Clip
Brush Lead
3. Loosen the terminal screw. Pull the brush lead away, but
leave the motor lead in place. Remove the brush and
spring.
4. Inspect the commutator for burning, excessive pitting or
gouging. A black color on the commutator is normal.
Commutator
5. Install the new brush so its lead slides in the long slot of
the brush holder. Push the terminal under the terminal
screw washer. Ensure the motor lead is still connected at
the screw. Tighten the screw.
Brush
Brush Holder
T
erminal Screw
Spring
Spring Clip
6. Place the spring on the brush as shown above. Push in
and hook the spring clip. Repeat this procedure for the
other side.
7. Reinstall both inspection covers.
If electric motor overloads and stops running,
IMMEDIATELY turn the motor off and follow the
Pressure Relief Procedure in the Cleanup section
of this manual. Wait until the motor cools
(approximately 30 minutes). Then push in the
bubble top, manual reset button, turn the motor on
and pressurize the system.
For CSA approved sprayers only: The ON/OFF switch is
also the RESET!
Airless Gun
Problem
A. Spitting gun
B. Gun will not shut off
C. Gun does not spray
Airless Gun
Problem
A. Pump delivers on upstroke
only or goes up slowly and
down fast (commonly called
downstroke dive)
B. Pump delivers on down stroke
only or goes up fast and down
slowly
C. Pump moves up and down
fast, delivering material
D. Pump moves up and down
slowly when spray gun is shut
off
E. Not enough uid pressure at
gun
F. Pump chatters on up or down
stroke
Cause
1. Air in system
2. Dirty gun
3. Needle assembly out of adjustment
4. Broken or chipped seat
1. Worn or broken needle & seat
2. Needle assembly out of adjustment
3. Dirty gun
1. No paint
2. Plugged lter or tip
3. Broken needle in gun
Cause
1. Lower foot valve ball is not seating due to
trash or wear
2. Material too viscous to siphon.
3. Air leaking in on siphon side or damaged
siphon hose. Siphon may be too small for
heavy material.
1. Upper ball is not seating due to trash or
wear
2. Lower packing set is worn
1. Material container is empty or material is
too thick to ow through siphon hose
2. Bottom ball stuck to foot valve seat
3. Siphon hose is kinked or loose
1. Loose connections. Bleed valve is open
partially or bleed valve is worn. Lower
packing seat is worn.
2. Upper and/or lower ball not seating
1. Spray tip is worn
2. Outlet lter or gun lter is clogged
3. Low voltage and/or inadequate amperage
4. Hose size or length is too small or too long
1. Solvent has caused upper packing to swell
Solution
1. Inspect connections for air leaks.
2. Disassemble and clean.
3. Inspect and adjust.
4. Inspect and replace.
1. Replace.
2. Adjust.
3. Clean.
1. Check uid supply.
2. Clean.
3. Replace.
Solution
1. Remove foot valve assembly. Clean and inspect.
Test foot valve by lling with water; if ball fails to seal
the seat, replace ball.
2. Thin material — contact manufacturer for proper
thinning procedures.
3. Tighten all connections between pump and paint
container. If damaged, replace. Switch to larger
diameter siphon set.
1. Check upper seat and ball with water. If ball fails to
seal, replace seat.
2. Replace packing set if worn.
1. Rell with new material. If too thick, remove siphon
hose, immerse uid section in material, and start
pump to prime. Add thinner to material. Change to
bigger siphon set. Open bleed valve to remove air
and restart pump.
2. Remove foot valve. Clean ball and seat.
3. Straighten.
1. Check all connections between pump and gun.
Tighten as necessary. If material is owing from
bleed hose, close bleed valve or replace, if
necessary. Should none of the above be evident,
replace lower packing.
2. Reseat balls by cleaning.
1. Replace.
2. Clean or replace lter.
3. Check electrical service. Correct as required.
4. Increase hose size to minimize pressure drop
through hose and/or reduce hose length.
1. Replace packing.
Troubleshooting
© Titan Tool Inc. All rights reserved. 13
14 © Titan Tool Inc. All rights reserved.
Hydraulic Motor
Problem
A. Oil motor stalls at bottom (no
unusual heat problems)
B. Oil motor stalls at top (no
unusual heat problems)
C. Low pressure (okay on down
stroke, sluggish on up.stroke
— high heat)
NOTE: Engine labors on upstroke,
idles back at stall on the
down stroke.
D. Low pressure (both strokes -
high heat)
NOTE: Engine labors at stall on
both strokes.
Cause
1. Fluid pump piston seat unthreaded
2. Valve sticking or oil motor trip rod shifter
assembly separated
1. Valve sticking
2. Broken spring retainer (valve rod
assembly)
3. Broken spring or valve rod
4. Air in hydraulic motor
5. Air in uid pump
1. Blown piston seal
2. Cracked piston
1. Blown center o-rings on spool valve
2. Bad hydraulic pump
Solution
1. If connecting rod is okay, remove cylinder head
plug and pop valve down. Replace plug and start
machine. If machine cycles up and stops at bottom
again, then problem is piston seat on uid pump.
Check piston seat. Repair or replace as necessary.
If piston seat is okay and problem does not change,
check oil motor.
2. Remove valve and check for scratches and rough
movement when sliding it up and down. Replace
valve and spool in this condition. Check trip rod
for possible separation.and spool in this condition.
Check trip rod for possible separation.
1. Remove valve and check for scratches and rough
movement when sliding it up and down. Replace
valve and spool in this condition.
2. Replace valve rod assembly.
3. Replace valve rod assembly.
4. Reset valve. Purge Air, generally accomplished by
low pressure cycling of motor/pump assembly for
5–10 minutes. Check for causes of air introduction:
• Loose ttings in tank.
• Loose ttings on hydraulic pump.
• Loose hose connections.
• Low oil in reservoir.
5. Stall at top can occur randomly when uid pump
picks up air. Reset valve. Avoid air in the uid pump.
1. Before dismantling oil motor, start machine. With
pump cycling under pressure, touch the hydraulic
cylinder and the head to see if cylinder or head gets
hotter. This will help determine if piston seal is blown
or piston nut is broken. If heat is on the head, check
the o-rings on spool valve.
2. Dismantle oil motor and check piston seals cylinder
bore and piston nut. Pay special attention to piston
nut. It can be cracked and not show externally.
1. Before dismantling oil motor, start machine. With
pump cycling under pressure, touch the head to see
if the head becomes hotter. This will help determine
if center o-ring is blown on spool valve. If hot, remove
and replace o-ring.
2. Replace hydraulic pump.
Troubleshooting
© Titan Tool Inc. All rights reserved. 15
Spray Patterns
Problem
A. Tails
B. Hour glass
C. Distorted
D. Pattern expanding and
contracting (surge)
E. Round pattern
Cause
1. Inadequate uid delivery
1. Inadequate uid delivery
1. Plugged or worn nozzle tip
1. Suction leak
2. Pulsating uid delivery
1. Worn tip
2. Fluid too heavy for tip
Solution
1. Fluid not atomizing correctly:
Increase uid pressure. Change to smaller tip orice
size. Reduce uid viscosity. Reduce hose length.
Clean gun and lter(s). Reduce number of guns
using pump.
1. Same as above.
1. Clean or replace nozzle tip.
1. Inspect for suction hose leak.
2. Change to a smaller tip orice size. Install pulsation
dampener in system or drain existing one. Reduce
number of guns using pump. Remove restrictions in
system; clean tip screen if lter is used.
1. Replace tip.
2. Increase pressure. Thin material. Change nozzle tip.
Troubleshooting
Français
16 © Titan Tool Inc. Tous droits réservés.
Consignes de sécurite important · Lire toutes ces consignes avant
Indique une situation à risque, laquelle, si elle n’est
pas évitée, peut entraîner des blessures graves,
voire la mort.
Pour réduire les risques d’incendie ou d’explosion,
de choc électrique et de blessure, vous devez lire
et comprendre les directives figurant dans ce
manuel. Familiarisez-vous avec les commandes et
l’utilisation adéquate de l’équipement.
AVERTISSEMENT – Pour réduire le
risque d’incendie ou d’explosion :
1. Ne pulvérisez pas de matières inammables
ou combustibles près d’une amme nue, de
voyants lumineux ou de sources d’ignition
telles que des objets chauds, cigarettes,
moteurs, matériel et appareils électriques.
Évitez de produire des étincelles en connectant et en
déconnectant les cordons électriques.
2. Pour les appareils destinés à n’utiliser que des produits à
l’eau – Ne pulvérisez pas et ne les nettoyez pas avec des
liquides inammables. Exclusivement pour usage avec
liquides à base d’eau.
3. Pour les appareils destinés à un usage exclusif avec des
produits à l’eau ou des produits minéraux de type alcool
avec un point d’éclair minimum de 38 ºC (100 ºF) – Ne
pulvérisez pas et ne les nettoyez pas avec des liquides
ayant un point d’éclair inférieur à 38 ºC (100 ºF). Le
point d’éclair est la température à laquelle un uide peut
produire sufsamment de vapeur pour s’enammer.
4. L’écoulement de peinture ou de solvant dans l’équipement
peut produire de l’électricité statique. L’électricité statique
crée un risque d’incendie ou d’explosion en présence
de fumées de peinture ou de solvant. Toutes les pièces
du système du pulvérisateur, y compris la pompe,
l’ensemble du tuyau, le pistolet de pulvérisation et les
objets dans et autour de la zone de pulvérisation doivent
être correctement reliés à la terre pour protéger contre les
décharges d’électricité statique et les étincelles. N’utilisez
que des tuyaux conducteurs ou reliés à la terre pour
pulvérisateurs de peinture sous vide à haute pression,
spéciés par le fabricant.
5. Vériez que tous les conteneurs ou systèmes de stockage
sont reliés à la terre pour éviter les décharges d’électricité
statique.
6. Connectez à une prise électrique avec prise de terre
et utilisez des rallonges électriques reliées à la terre.
N’utilisez pas d’adaptateur 3 à 2.
7. N’utilisez pas de peinture ou de solvant contenant du
halon, par exemple, le chlore, les agents antimoisissure
à l’eau de Javel, le chlorure de méthylène et le
trichloroéthane. Ils ne sont pas compatibles avec
l’aluminium. Contactez le fournisseur de revêtements pour
connaître la compatibilité du matériau avec l’aluminium.
8. La zone de pulvérisation doit toujours être bien aérée.
Une bonne quantité d’air frais doit constamment traverser
la zone de pulvérisation pour éviter les accumulations de
vapeurs inammables. Le système de pompage doit être
placé dans une zone bien aérée. Ne pulvérisez pas le
système de pompage.
9. Ne fumez pas dans la zone de pulvérisation.
10. N’actionnez pas d’interrupteurs électriques, de moteurs ou
autres dispositifs produisant des étincelles dans la zone
de pulvérisation.
11. Maintenez la propreté de la zone et veillez à ce qu’elle ne
contienne pas de conteneurs de peinture ou de solvant,
de chiffons et autres matières inammables.
12. Sachez ce que contiennent la peinture et les solvants
pulvérisés. Lisez les ches de sécurité du matériel
(MSDS) et les étiquettes apposées sur les conteneurs
de peintures et de solvants. Respectez les consignes de
sécurité du fabricant de peinture et de solvant.
13. Placez la pompe à une distance minimum de 7,62 mètres
(25 pieds) de l’objet à pulvériser, dans une zone bien
aérée (ajoutez de la longueur de tuyau si besoin est). Les
vapeurs inammables sont souvent plus lourdes que l’air.
La zone près du sol doit être très bien aérée. La pompe
contient des pièces qui produisent des arcs et émettent
des étincelles pouvant enammer les vapeurs.
14. Le plastique peut causer des étincelles d’électricité
statique. N’accrochez aucun plastique dans une zone
de pulvérisation fermée. N’utilisez pas de toiles de
protection en plastique quand vous pulvérisez une matière
inammable.
15. Ayez un extincteur en bon état de fonctionnement à portée
de main.
AVERTISSEMENT – Pour réduire le
risque de pénétration dans la peau :
DANGER :
Blessure par injection – Le jet de fluide à haute pression
produit par cet équipement peut transpercer la peau et les
tissus sous-jacents, ce qui produit de graves blessures et
peut entraîner une amputation. Consultez immédiatement
un médecin. NE TRAITEZ PAS UNE INJECTION COMME UNE
SIMPLE COUPURE.
1. Ne dirigez pas le pistolet sur et ne pulvérisez pas les
personnes ou les animaux.
2. N’approchez pas les mains ni d’autres parties du corps de
la sortie du produit. Par exemple, ne tentez pas d’arrêter
une fuite avec une partie du corps.
3. Utilisez toujours le protège-embout de la buse. Ne
pulvérisez pas sans que le protège-embout de la buse ne
soit installé.
4. Utilisez exclusivement un embout de buse spécié par le
fabricant.
5. Prenez garde quand vous nettoyez ou que vous changez
les embouts de buse. Si l’embout se bouche pendant
que vous pulvérisez, verrouillez TOUJOURS la détente
du pistolet, arrêtez la pompe et libérez toute la pression
avant de réparer ou de nettoyer l’embout ou le protecteur
ou avant de changer d’embout. La pression n’est pas
libérée par l’arrêt du moteur. La poignée du robinet-valve
PRIME/SPRAY (AMORÇAGE/ PULVÉRISATION) doit
être placée sur PRIME pour libérer la pression. Consultez
la PROCÉDURE DE LIBÉRATION DE PRESSION décrite
dans le manuel de la pompe.
6. Ne laissez pas l’appareil sous tension ou sous pression
quand vous vous en éloignez. Quand vous n’utilisez pas
l’appareil, éteignez-le et libérez la pression conformément
aux instructions du fabricant.
7. La pulvérisation à haute pression peut injecter des
toxines dans le corps et causer de graves blessures
corporelles. Si une telle injection se produisait, consultez
immédiatement un médecin.
8. Vériez les tuyaux et les pièces pour détecter des signes
d’endommagement : une fuite peut injecter le produit dans
la peau. Inspectez le tuyau avant chaque emploi. Changez
tous les tuyaux ou pièces endommagés.
9. Ce système peut produire une pression de 3300 PSI
/ 22.8 MPa. N’utilisez que les pièces de rechange ou
les accessoires spéciés par le fabricant et ayant une
pression nominale minimum de 3300 PSI. Ceci est valable
Français
© Titan Tool Inc. Tous droits réservés. 17
Consignes de sécurite important · Lire toutes ces consignes avant
pour les embouts de pulvérisation, les protecteurs de
buse, les pistolets, les rallonges, les raccords et le tuyau.
10. Verrouillez toujours la détente quand vous ne pulvérisez
pas. Vériez que le verrou de la détente fonctionne
correctement.
11. Vériez que toutes les connexions sont bien serrées avant
d’utiliser l’appareil.
12. Sachez comment arrêter l’appareil et le dépressuriser
rapidement. Soyez bien familiarisé avec les commandes.
La pression n’est pas libérée lorsque le moteur est
arrêté. La poignée du robinet-valve PRIME/SPRAY
(AMORÇAGE/PULVÉRISATION) doit être placée
sur PRIME pour libérer la pression. Consultez la
PROCÉDURE DE LIBÉRATION DE PRESSION décrite
dans le manuel de la pompe.
13. Retirez toujours l’embout de pulvérisation avant de rincer
ou de nettoyer le système.
AVERTISSEMENT – Pour réduire le risque de
blessure :
1. Portez toujours les gants, la protection oculaire, les
vêtements et un respirateur ou masque appropriés
quand vous peignez. Vapeurs dangereuses – Les
peintures, solvants, insecticides et autres matières
peuvent être dangereux s’ils sont inhalés ou entrent en
contact avec le corps. Les vapeurs peuvent provoquer
d’importantes nausées, une perte de connaissance ou un
empoisonnement.
2. Ne travaillez pas et ne pulvérisez pas près d’enfants.
Éloignez toujours les enfants de l’équipement.
3. Ne travaillez pas avec les bras au-dessus de la tête ni sur
un support instable. Appuyez-vous bien sur les deux pieds
pour toujours conserver l’équilibre.
4. Soyez attentif et regardez ce que vous faites.
5. N’utilisez pas l’appareil quand vous êtes fatigué ou sous
l’inuence de drogues ou d’alcool.
6. Ne faites pas de nœuds avec le tuyau et ne le tordez pas
trop. Le tuyau à vide peut présenter des fuites suite à
l’usure, les nœuds ou les mauvais traitements. Une fuite
risque d’injecter du produit dans la peau.
7. N’exposez pas le tuyau à des températures ou des
pressions supérieures à celles spéciées par le fabricant.
8. N’utilisez pas le tuyau pour tirer ou soulever l’équipement.
9. Utilisez la plus basse pression possible pour rincer
l’équipement.
10. Respectez tous les codes locaux, étatiques et nationaux
qui régulent la ventilation, la prévention d’incendies et le
fonctionnement.
11. Les normes de sécurité du gouvernement des États-Unis
ont été adoptées dans la loi Occupational safety and
Health Act (OSHA). Ces normes, en particulier la partie
1910 des Normes générales et la partie 1926 des Normes
de construction, doivent être consultées.
12. Avant chaque emploi, vériez tous les tuyaux pour
détecter d’éventuelles coupures, fuites, abrasion ou
couvercle bombé. Vériez l’état ou le mouvement des
accouplements. Changez immédiatement le tuyau si l’une
de ces conditions est vériée. Ne réparez jamais un tuyau
de peinture. Remplacez-le par un tuyau conducteur à
haute pression.
13. Ne pulvérisez pas à l’extérieur par temps venteux.
14. Débranchez toujours le cordon électrique de la prise avant
de travailler sur l’équipement.
IMPORTANT: Ne pas soulever par la poignée du chariot lors
du chargement ou du déchargement.
Sécurité du moteur à essence
L’État de la Californie reconnaît que les gaz
d’échappement de cet appareil contiennent des
produits chimiques susceptibles de causer le
cancer, des malformations congénitales ou
pouvant être nocifs pour le système reproducteur.
1. Les moteurs Honda sont conçus pour être ables et
sécuritaires lorsqu’ils sont utilisés selon les directives.
Lire et comprendre le guide d’utilisation de Honda avant
de faire fonctionner le moteur. Le non-respect de cet
avertissement risque de causer des blessures graves ou
d’endommager l’appareil.
2. An de prévenir les risques d’incendie et d’assurer une
ventilation adéquate, garder le moteur à une distance
d’au moins un mètre (3 pi) des bâtiments et des autres
appareils durant le fonctionnement. Ne pas placer des
objets inammables près du moteur.
3. Les enfants et les animaux doivent être tenus à l’écart de
la zone de fonctionnement de l’appareil an d’éviter les
risques de brûlures causées par les composants chauds
du moteur ou par les équipements utilisés avec le moteur.
4. Savoir comment couper le moteur rapidement et bien
comprendre le fonctionnement de toutes les commandes.
Ne jamais laisser quiconque utiliser le moteur sans lui
avoir d’abord fourni les directives appropriées.
5. Le carburant est une matière extrêmement inammable et
peut exploser sous certaines conditions.
6. Ravitailler en carburant dans un endroit bien aéré une
fois le moteur arrêté. Ne pas fumer et s’assurer qu’il n’y ait
ni ammes ni étincelles dans la zone de ravitaillement ou
d’entreposage du carburant.
7. Ne pas trop remplir le réservoir d’essence. Après le
ravitaillement, s’assurer que le bouchon du réservoir soit
bien fermé et serré.
8. Prendre soin de ne pas renverser de carburant lors du
ravitaillement, car les vapeurs émanant du carburant ou le
carburant déversé accidentellement peuvent s’enammer.
En cas de déversement, s’assurer que l’endroit soit
complètement sec avant de démarrer le moteur.
9. Ne jamais mettre le moteur en marche dans un endroit
fermé ou restreint, car les gaz d’échappement contiennent
des matières toxiques, telles que le monoxyde de
carbone, susceptibles de provoquer des évanouissements
ou même d’entraîner la mort.
10. Le silencieux devient très chaud durant le fonctionnement
et le demeure pendant un certain temps une fois le moteur
arrêté. S’assurer d’attendre quelques minutes avant de
toucher au silencieux. Pour éviter les risques de brûlures
graves ou d’incendie, laisser le moteur se refroidir avant
de le transporter ou de l’entreposer à l’intérieur.
11. Ne jamais expédier ou transporter l’appareil lorsque le
réservoir est rempli de carburant.
Ne pas utiliser cet appareil pour vaporiser de l’eau
ou de l’acide.
Español
18 © Titan Tool Inc. Todos los derechos reservados.
Información de seguridad importante · Lea toda la información de
seguridad antes de operar el equipo. GUARDE ESTAS INSTRUCCIONES.
Indica una situación peligrosa que, de no evitarse,
puede causar la muerte o lesiones graves.
Para reducir los riesgos de incendios, explosiones,
descargas eléctricas o lesiones a las personas, lea
y entienda todas las instrucciones incluidas en
este manual. Familiarícese con los controles y el
uso adecuado del equipo.
ADVERTENCIA – Para reducir el riesgo
de incendio o explosión:
1. No pulverice materiales inamables ni
combustibles cerca de llamas desnudas,
pilotos o fuentes de ignición como objetos
calientes, cigarrillos, motores, equipos
eléctricos o electrodomésticos. Evite
producir chispas al conectar y desconectar los cables de
alimentación.
2. Para unidades que se vayan a utilizar con materiales
acuosos — No pulverice ni limpie con líquidos inamables.
Para su uso con líquidos acuosos solamente.
3. Para unidades que se vayan a utilizar solamente con
materiales acuosos o de tipo de alcohol mineral con un
punto de inamación mínimo de 38 ºC (100 ºF) — No
pulverice ni limpie con líquidos que tengan un punto de
inamación por debajo de 38 ºC (100 ºF). El punto de
inamación es la temperatura a la que un uido puede
producir vapor suciente como para incendiarse.
4. La pintura o disolvente que pase por el equipo puede
producir electricidad estática. La electricidad estática
supone un riesgo de incendio o explosión en presencia de
emanaciones de pintura o disolvente. Todas las piezas del
sistema pulverizador, incluyendo la bomba, el conjunto de
mangueras, la pistola pulverizadora y los objetos dentro
y alrededor de la zona de pulverización se conectarán
a tierra para protegerlos frente a descargas estáticas y
chispas. Utilice solamente mangueras para pulverizadores
de pintura airless (sin aire) de alta presión conductoras o
con toma a tierra especicadas por el fabricante.
5. Compruebe que todos los recipientes y sistemas de
recogida están conectados a tierra para evitar descargas
eléctricas.
6. Conecte a una salida con toma a tierra y utilice cables
alargadores puestos a tierra. No utilice un adaptador de 3
a 2.
7. No utilice pintura o disolvente que contenga hidrocarburos
halogenados, como cloro, fungicida blanqueador, cloruro
de metileno y tricloroetano. No son compatibles con el
aluminio. Póngase en contacto con el proveedor del
material para conocer su compatibilidad con el aluminio.
8. Mantenga la zona de pulverización bien ventilada.
Asegúrese de que circula aire fresco por la zona para
evitar que se acumulen vapores inamables en el aire de
la zona de pulverización. Ponga el conjunto de la bomba
en una zona bien ventilada. No pulverice el conjunto de la
bomba.
9. No fume en la zona de pulverización.
10. No encienda interruptores de luces, motores ni productos
similares que puedan producir chispas en la zona de
pulverización.
11. Mantenga la zona limpia y despejada de botes de pintura
y disolventes, trapos y otros materiales inamables.
12. Infórmese del contenido de la pintura y de los disolventes
que pulverice. Lea las hojas de datos sobre seguridad
de los materiales (MSDS) y las etiquetas en los botes de
pintura y disolvente. Siga las instrucciones de seguridad
del fabricante de la pintura y del disolvente.
13. Coloque la bomba al menos a 7,62 metros (25 pies) del
objeto que se va a pulverizar en una zona bien ventilada
(añada más manguera si fuera necesario). Los vapores
inamables suelen ser más pesados que el aire. La
zona del suelo debe estar muy bien ventilada. La bomba
contiene piezas que forman arcos que producen chispas y
pueden inamar los vapores.
14. El plástico puede producir chispas estáticas. Nunca utilice
plástico para cercar la zona de pulverización. No utilice
cortinas de plástico mientras pulveriza material inamable.
15. Deberá contar con equipos extintores de incendios que
funcionen correctamente.
ADVERTENCIA – Para reducir el riesgo
de daños en la piel:
PELIGRO:
Lesión causada por inyección. La corriente de líquido a alta
presión que produce este equipo puede perforar la piel y
tejidos subcutáneos, pudiendo provocar graves lesiones y
posibles amputaciones. Visite a un médico inmediatamente.
NO TRATE UNA LESIÓN CAUSADA POR INYECCIÓN COMO
UN SIMPLE CORTE.
1. No apunte con la pistola ni pulverice sobre ninguna
persona ni animal.
2. Mantenga las manos y el resto del cuerpo lejos de la
descarga. Por ejemplo, no trate de detener fugas con
ninguna parte de su cuerpo.
3. Utilice siempre el protector de la boquilla. No pulverice sin
el protector en su sitio.
4. Utilice solamente la boquilla especicada por el fabricante.
5. Tenga cuidado al limpiar y cambiar las boquillas. Si la
boquilla se atasca durante la pulverización,
ponga SIEMPRE el seguro del gatillo de la pistola, apague
la bomba y libere toda la presión antes de reparar, limpiar
el protector o la boquilla o cambiar la boquilla. La presión
no se libera apagando el motor. Para liberar la presión hay
que poner la manija de la válvula PRIME/SPRAY (cebar/
pulverizar) en PRIME. Consulte el Procedimiento para
liberar presión que se describe en el manual de la bomba.
6. No deje el aparato con corriente ni con presión cuando
nadie esté pendiente de ella. Cuando no utilice el aparato,
apáguelo y libere la presión siguiendo las instrucciones
del fabricante.
7. La pulverización a alta presión puede inyectar toxinas en
el cuerpo y producir daños graves en el mismo. En caso
de que esto ocurra, visite a un médico inmediatamente.
8. Compruebe las mangueras y las piezas en busca de
daños; una fuga puede inyectar material en la piel.
Inspeccione la manguera antes de cada uso. Sustituya las
mangueras o las piezas dañadas.
9. Este sistema es capaz de producir 3300 PSI / 22.8
MPa. Utilice solamente piezas de repuesto o accesorios
especicados por el fabricante y con una capacidad
nominal de 3300 PSI como mínimo. Entre ellos se
incluyen boquillas pulverizadoras, protectores para las
boquillas, pistolas, alargadores, racores y mangueras.
10. Ponga siempre el seguro del gatillo cuando no esté
pulverizando. Verique que el seguro del gatillo funciona
correctamente.
11. Antes de utilizar el aparato, verique que todas las
conexiones son seguras.
Español
© Titan Tool Inc. Todos los derechos reservados. 19
Información de seguridad importante · Lea toda la información de
seguridad antes de operar el equipo. GUARDE ESTAS INSTRUCCIONES.
12. Aprenda a detener el aparato y a liberar la presión
rápidamente. Familiarícese a conciencia con los controles.
La presión no se libera apagando el motor. Para liberar
la presión hay que poner la manija de la válvula PRIME/
SPRAY (cebar/pulverizar) en PRIME. Consulte el
Procedimiento para liberar presión que se describe en el
manual de la bomba.
13. Quite siempre la boquilla pulverizadora antes de enjuagar
o limpiar el sistema.
ADVERTENCIA – Para reducir el riesgo de lesiones:
1. Cuando pinte, lleve siempre guantes, protección para los
ojos, ropa y un respirador o máscara adecuados. Vapores
peligrosos: Las pinturas, disolventes, insecticidas y otros
materiales pueden ser perjudiciales si se inhalan o entran
en contacto con el cuerpo. Los vapores pueden producir
nauseas intensas, desmayos o envenenamiento.
2. Nunca utilice el aparato ni pulverice cerca de niños.
Mantenga el equipo alejado de los niños en todo
momento.
3. No se estire demasiado ni se apoye sobre un soporte
inestable. Mantenga los pies bien apoyados y el equilibrio
en todo momento.
4. No se distraiga y tenga cuidado con lo que hace.
5. No utilice el aparato si está fatigado o se encuentra bajo la
inuencia del alcohol o de las drogas.
6. No retuerza ni doble la manguera en exceso. En la
manguera airless pueden aparecer fugas a causa del
desgaste, de retorcimientos o de un mal uso. Una fuga
puede inyectar material en la piel.
7. No exponga la manguera a temperaturas o presiones que
superen las especicadas por el fabricante.
8. No utilice la manguera como elemento de fuerza para tirar
del equipo o levantarlo.
9. Utilice la presión más baja posible para enjuagar el
equipo.
10. Cumpla todos los reglamentos locales, estatales y
nacionales pertinentes relativos a ventilación, prevención
de incendios y funcionamiento.
11. Las normas sobre seguridad del gobierno de los Estados
Unidos se han adoptado al amparo de la Ley de salud
y seguridad ocupacional (OSHA). Deben consultarse
tres normas, particularmente la sección 1910 de las
Normas generales y la sección 1926 de las Normas sobre
construcción.
12. Cada vez que vaya a utilizar el equipo, compruebe antes
todas las mangueras en busca de cortes, fugas, abrasión
o bultos en la cubierta. Compruebe el movimiento
de los acoplamientos y si están dañados. Sustituya
inmediatamente una manguera si descubre alguna de
estas anomalías. No repare nunca una manguera de
pintura. Sustitúyala por una manguera conductora a alta
presión.
13. No pulverice al aire libre si hace viento.
14. Desenchufe siempre el cable antes de trabajar en el
equipo.
IMPORTANTE: No cargue el equipo por el asa del carrito
durante la carga y descarga.
Seguridad con los motores de gasolina
El escape del motor de esta unidad contiene
químicos que el Estado de California ha
determinado causan cáncer, defectos de
nacimiento u otros daños al sistema reproductor.
1. Los motores Honda están diseñados para proporcionar
un servicio seguro y able, si se utilizan de acuerdo a
las instrucciones. Lea y entienda las instrucciones del
Manual del Propietario de Honda antes de utilizar el
motor. De lo contrario, podría causar lesiones personales
o daño al equipo.
2. Para evitar peligros de incendio y para proporcionar una
ventilación adecuada, mantenga el motor por lo menos a
1 metro de los edicios y de otro equipo durante su uso.
No coloque objetos inamables cerca del motor.
3. Mantenga a los niños y las mascotas alejados de la zona
de trabajo, pues existe la posibilidad de quemaduras
causadas por los componentes calientes del motor o
lesiones causadas por cualquier equipo en el que se
utilice el motor.
4. Sepa cómo apagar el motor rápidamente y comprenda el
funcionamiento de todos los controles. Nunca permita a
nadie operar el motor sin las instrucciones apropiadas.
5. La gasolina es extremadamente inamable y es explosiva
bajo ciertas condiciones.
6. Llene el tanque de combustible en un lugar bien ventilado
y con el motor apagado. No fume ni permita que haya
llamas ni chispas en la zona de llenado ni en donde se
almacena el combustible.
7. No llene en exceso el tanque de combustible. Después
de ponerle combustible, asegúrese de que la tapa del
tanque esté cerrada completamente.
8. Tenga cuidado de no derramar el combustible. Los gases
del combustible o el combustible derramado pueden
encenderse. Si se derrama combustible, asegúrese de
que la zona esté seca antes de encender el motor.
9. Nunca utilice el motor en un lugar encerrado o connado.
El escape contiene gas de monóxido de carbono
venenoso; la exposición a este gas puede causar pérdida
del conocimiento y puede conducir a la muerte.
10. El escape se calienta mucho durante su uso y permanece
caliente durante un rato después de apagar el motor.
Asegúrese de no tocar el escape cuando esté caliente.
Para evitar quemaduras graves o peligros de incendio,
deje que el motor se enfríe antes de transportarlo o
guardarlo bajo techo.
11. Nunca envíe ni transporte la unidad con gasolina en el
tanque.
No utilice este equipo para rociar agua o ácido.
20 © Titan Tool Inc. All rights reserved.
Parts Lists and Service Instructions
Main Assembly
1
5
6
4
2
3
7
8
9
10
13
14
11
12
Item Part # Description Quantity
1 451-135 Motor/pump assembly ..............................1
2 703-136 O-ring ........................................................1
3 703-137 Swivel tting assembly (includes item 2) ..1
4 944-030 Bleed valve ...............................................1
5 451-136 Filter assembly .........................................1
6 451-139 Bleed hose................................................1
7 730-334 Hose clamp ...............................................1
8 ---------- Belt guard assembly .................................1
9 ---------- Hydraulic system ......................................1
10 449-181 Belt, “V” (gas model) .................................1
Item Part # Description Quantity
11 506-275 Convertokit, 4.8 HP, Honda, gasoline
(gas model) ...............................................1
12 451-070 Cart assembly ...........................................1
13 862-428 Screw ........................................................2
14 862-002 Washer .....................................................2
15 506-279 Convertokit, DC electric, 120V
(electric model, includes belt, not shown) 1
16 506-251 Convertokit, 3 HP, electric, 230V
(electric model, not shown).......................1
1
2
3
4
6
13
5
6
7
9
8
10
12
11
14
15
16
7
17
© Titan Tool Inc. All rights reserved. 21
Cart Assembly (P/N 451-070)
Belt Guard Assembly
Item Part # Description Quantity
1 590-502 Handle ......................................................1
2 590-507 Snap button ..............................................2
3 590-506 Handle washer..........................................2
4 590-508 Roll pin ......................................................2
5 590-504 Handle sleeve ...........................................2
6 590-100 Retaining ring ...........................................6
7 870-004 Washer .....................................................4
8 451-064 Swing arm axle .........................................1
9 759-034 Cotter pin ..................................................1
10 451-074 Grip ...........................................................1
Item Part # Description Quantity
1 449-217 Belt guard, gas model...............................1
449-216 Belt guard, 230V electric model
2 858-636 Screw ........................................................2
3 858-002 Lockwasher ..............................................2
4 862-411 Nut ............................................................1
5 449-185 Belleville washer .......................................1
6 862-001 Flat washer ...............................................1
7 449-187 Clip ...........................................................1
8 449-198 Flat washer ...............................................1
9 449-166 Bolt ...........................................................1
759-074 Label (not shown)
Item Part # Description Quantity
11 451-113 Lock pin ....................................................1
12 451-112 Spring .......................................................1
13 451-059 Swing arm .................................................1
14 856-002 Lock washer .............................................4
15 856-921 Screw ........................................................4
16 451-053 Frame .......................................................1
17 670-109 Wheel .......................................................2
18 451-052 Plug (not shown).......................................2
19 451-455 Cart handle spacer (not shown) ...............1
1
5
6
7
8
9
2
3
4
22 © Titan Tool Inc. All rights reserved.
Hydraulic Motor
29
See page 31
for installation
instructions.
28
29
27
25
Item Part # Description Quantity
1 235-018 Trip retainer ..............................................2
2 141-007 O-ring ........................................................2
3 325-005 Trip spring, ...............................................2
4 569-016 Ball, SS .....................................................2
5 441-908 Spool / sleeve set .....................................1
6 441-152 O-ring ........................................................3
7 235-030 Cylinder head plug....................................1
8 441-217 O-ring ........................................................1
9 858-811 Flex lock nut .............................................1
10 451-121 Elbow, 90º ................................................1
11 235-112FZ Cylinder head ...........................................1
12 431-032 O-ring ........................................................2
13 431-053 Sleeve retainer .........................................1
14 431-054 Retainer ring .............................................1
15 192-000 Elbow ........................................................1
16 235-022 Piston retainer screw ................................1
17 235-014 Piston ........................................................1
18 235-027 Piston seal ................................................1
19 235-026 O-ring ........................................................1
20 235-021 Valve rod assembly ..................................1
21 235-948 Piston rod .................................................1
22 235-001 Lock ring ...................................................1
23 235-007 Cylinder ....................................................1
24 235-028 Rod seal ...................................................1
25 235-129 Motor/pump block .....................................1
26 235-029 Motor tube ................................................1
27 235-125 Tee ...........................................................1
28 431-019 O-ring kit ...................................................1
29 700-499 O-ring ........................................................2
235-050 Motor service kit, minor (includes items
2–4, 6, 8, 9, 12, 18, 19, and 24)
Servicing the Hydraulic Motor
Perform this procedure using the necessary parts from Motor
Service Kit — Minor (P/N 235-050). If the hydraulic motor is
operable, start the machine and jog the piston rod (21) into its top
position.
NOTE: Servicing of the hydraulic motor should be
carried out in a clean, dust free area only. Any
dust or metallic particles left in the motor or
entering it on reassembly may damage the
critical parts and affect its service life and
warranty. All parts should be inspected for
absolute cleanliness.
Disassembling the Hydraulic Motor
1. Disconnect the pressure hose from the elbow (34 and 35
in Hydraulic System parts list) on the back of the hydraulic
pump.
2. Remove the two mounting screws and two lock washers
(13 and 14 in Main Assembly parts list) that attach the
motor/pump assembly to the cart.
3. Place the motor/pump assembly in a vise, holding it
securely by the motor/pump block (25).
4. Remove cylinder head plug (7).
5. Loosen lock ring (22) with a spanner wrench and unthread
tube retaining nut on tee (27). Loosen tube retaining
nut on elbow (15). Slide the nut down. Push motor tube
(26) into tee (27) far enough to clear elbow (15). Slowly
unthread cylinder head (11) and Iift it just high enough
above the cylinder (23) to reach the valve rod assembly
(20) with vise grip pliers.
6. The piston rod (21) should be near the top of its stroke for
disassembly. It may be necessary to use a wood or nylon
driver to push the piston rod up to its top position.
© Titan Tool Inc. All rights reserved. 23
7. Grip the valve rod securely with vise grip pliers and then
remove the FlexLoc nut (9) from the top of the valve rod
assembly (20). Be careful that spool (5) does not fall. The
cylinder head (11) can now be lifted off. Unthread the
cylinder (23) from the motor/pump block (25). Note: An
extra lock ring (22) can be used to jam the two lock rings
together on the cylinder and a pipe wrench can be used to
unthread the cylinder (23) from the motor/pump block (25).
Connecting
Pin
Retaining
Ring
8. To remove the
connecting pin, slide
the retaining ring
down with a small
screwdriver, and then
push the connecting
pin out.
9. Remove the piston
rod assembly from
the motor/pump block
(25).
10. Remove rod seal (24), being extremely careful not to
scratch the seal groove in the motor/pump block (25).
11. Place the piston retainer screw (16) on the piston rod
assembly in a vise. Slide a long bar through the hole at
the base of the piston rod for leverage, and unthread the
piston rod from the piston retainer screw.
12. Remove piston (17) and lift out valve rod assembly (20).
13. Remove piston seal (18) and o-ring (19).
14. Remove trip retainers (1), trip springs (3), and balls (4)
from cylinder head (11). Remove o-rings (2) from trip
retainers (1).
15. Remove retaining ring (14) and sleeve retainer (13).
Gently tap spool/sleeve set (5) out of cylinder head (11)
using a wood or nylon rod.
16. Inspect piston rod (21) and cylinder (23) for wear,
scratches, and dents. Replace if damaged.
17. Inspect spool valve (5) for wear. Replace if necessary.
spool valve should move smoothly and freely with no force
by holding in a vertical position. If it does not, it can cause
the motor to stall.
Reassembling the Hydraulic Motor
1. Separate spool/sleeve set (5). Place o-rings (6) onto
sleeve. Lubricate o-rings with hydraulic oil. Gently push
the sleeve into cylinder head (11) with the atter side of
the sleeve facing out. Use a nylon rod to tap sleeve down
until it reaches its full depth. Do not use any other type
of tool that might damage or leave particles or residue on
the sleeve. Install the spool through the top of the cylinder
head, down into the sleeve.
IMPORTANT: Do not use Piston Lube pump packing
lubricant. It is a solvent and will severely damage seals and
O-Rings of the hydraulic motor.
2. Install o-rings (2) on trip retainers (1). Install trip retainer
balls (4) followed by springs (3) which, when installed, will
hold spool/sleeve set (5) in proper place for assembly.
3. Install sleeve retainer (13) followed by snap ring (14) into
cylinder head (11), which will hold valve sleeve in place.
Install o-ring (12) in the o-ring groove of the cylinder head.
4. Replace lower seal (24) in motor/pump block (25). Be sure
the open portion of the seal is facing upward (V). This seal
requires no special tool.
5. Place piston rod (21) in vise. Inspect valve rod assembly
(20) for any damage. Make sure the lock nut at the bottom
of the valve rod assembly (20) is secure. DO NOT remove.
Then, place into piston rod (21) as illustrated. Install o-ring
(19), lubricating it well and replacing piston (17) onto
piston rod (21). Put one drop of blue Loctite on the piston
retainer screw (16). Tighten piston retainer screw until
piston is locked into place. Check valve rod assembly (20)
for normal spring action at this time.
6. Install piston seal (18) with lips facing downward. Carefully
install o-ring (19). Expand the ring and stretch it sufciently
for installation.
7. With motor/pump block (25) still in vise, install lower seal
(24) by pushing it towards its groove with a properly sized
blunt rod. Then complete installation with the ngers. No
tool is necessary. Do not twist the seal.
8. Pre-lubricate the piston and valve rod assembly with
Coolo™ hydraulic uid (P/N 430-361). Install piston rod
(21) into motor/pump block (25) with a gently pushing and
rotating motion to work the piston rod in through the seal
(24).
NOTE: Inspect the bottom of piston rod (21) for nicks or
sharp areas that could damage the piston seal
during installation through the motor/pump block
(25).
9. Replace the connecting rod pin and retainer ring.
10. Install o-ring (12) on cylinder wall. Lubricate ring and inner
wall. With the piston rod held rmly, the cylinder should
be gently driven over the piston seal with a rubber mallet.
Tightly thread the cylinder into motor/pump block (25).
11. Raise piston rod (21) to top position and thread lock ring
(22) all the way up on upper threads of cylinder (23).
12. Pull valve rod assembly (20) up as far as it will travel and
grasp it with vise grip pliers. Then install cylinder head
(11), already assembled, over valve rod until the top
threads of the valve rod pass through the top of the spool/
sleeve set (5). The valve rod threads must be clean and
free of oil. Place one drop of blue Loctite on threads of
ex lock nut (9) and thread nut onto valve rod to full tight
position (do not over-tighten) while holding valve rod below
with vise grip pliers.
13. Thread cylinder head (11) down onto the cylinder (23)
and then back off just enough to reassemble hydraulic
ttings and motor tube (26). Tighten lock ring with spanner
wrench to hold cylinder head in position.
14. The tee assembly (27) and the elbow (15) use an o-ring
(28) to seal on the outer diameter (O.D.) of the motor
tube (26). The O.D. of the motor tube should be free of
scratches or sharp edges. The lock nuts on these ttings
rst should be hand tightened, then wrench tightened
another half turn.
15. Install o-ring (8) onto cylinder head plug (7). Tighten.
24 © Titan Tool Inc. All rights reserved.
Hydraulic Motor Cut-Away
Torque flex locknut to
10 ft./lbs. (146N/m).
Use blue Loctite.
Use blue
Loctite on
lock ring.
Seal lip must
face up.
Use
hydraulic
sealant.
Torque head plug to
15 ft./lbs. (219 N/m).
Do not over-tighten
o-ring seal.
Torque trip
retainers to
15 ft./lbs. (365 N/m).
Do not over-tighten
o-ring seal.
Torque piston
retainers to
75 ft./lbs. (1095 N/m).
Use red Loctite.
Seal lip must
face down.
Valve rod assembly
is factory set and
permanently Loctited.
Do not disassemble.
Fluid Section
1
5
6
7
8
15
14
3
23
24
4
4
2
3
Motor/
Pump
Block
10
9
13
12
11
16
3
18
17
19
21
20
22
Item Part # Description Quantity
1 143-019 Retaining ring ...........................................1
2 143-120 Connecting pin..........................................1
3 145-031 O-ring, Teon ............................................3
4 138-153 Packing set, leather/UHMWPE/steel ........2
5 142-004 Upper packing spring................................1
6 451-031 Displacement rod......................................1
7 138-001 Spring retainer ..........................................1
8 142-003 Lower packing spring................................1
9 451-085 Outlet valve cage ......................................1
10 138-225 Outlet valve ball ........................................1
11 236-012 Outlet valve seat .......................................1
12 236-032 Seal washer ..............................................1
13 236-031 Outlet valve housing .................................1
14 451-032 Cylinder spacer .........................................1
15 143-832 Pump cylinder ...........................................1
16 140-009 O-ring ........................................................1
17 236-030 Wave washer ............................................1
18 236-141 Foot valve cage ........................................1
19 178-700 Foot valve ball ..........................................1
20 143-026 Foot valve seat .........................................1
21 143-025 Seat o-ring ................................................1
22 451-132 Foot valve housing ...................................1
23 451-018 Inlet screen ...............................................1
24 431-054 Snap ring ..................................................1
143-501 Fluid section service kit, major (includes
items 6, 15, and uid section service kit,
minor P/N 144-050)
144-050 Fluid section service kit, minor (includes
items 1, 3, 4, 10, 12, 16, 19, 21, and
Loctite P/N 426-051)
451-133 Foot valve assembly
(includes items 18–24)
236-050 Outlet valve assembly
(includes items 9–13)
© Titan Tool Inc. All rights reserved. 25
Servicing the Fluid Section
IMPORTANT: Use of non-Titan service parts may void
warranty. Ask for original parts made by Titan for best
services. This pump should receive a routine servicing
after approximately 1,000 hours of use. Earlier servicing is
required if there is excessive leakage from the top packing
or if pump strokes become faster on one stroke or the other.
The use of Titan Piston Lube (P/N 314-480) is recommended
as an upper packing lubricant. Do not substitute oil, water,
or solvent for an upper packing lubricant.
Disassembling the Fluid Section
1. Remove the foot valve housing (22), pump cylinder (15),
and cylinder spacer (14) with a strap wrench.
2. Slide the retaining ring (1) up with a small screwdriver,
then push the connecting pin (2) out.
3. Pull the displacement rod (6) through the lower cavity of
the motor/pump block.
4. Remove the Teon o-ring (3), upper packing spring (5),
and upper packing set (4) from the motor/pump block.
5. Hold the displacement rod (6) in a vise by the ats at the
top of the displacement rod and remove the outlet valve
housing (13) with a wrench while holding the displacement
rod horizontal with a wooden support, if necessary.
Remove the seal washer (12), outlet valve seat (11), outlet
valve ball (10), outlet valve cage (9), lower packing set (4),
lower packing spring (8), and spring retainer (7).
6. Using a 1/2” extension bar attached to a 1/2” drive ratchet,
insert the end of the extension bar into the square opening
of the foot valve cage (18) inside the foot valve housing
(22). Unscrew and remove the foot valve cage along with
the wave washer (17) from the foot valve housing.
7. Remove the Teon o-ring (3), foot valve ball (19), foot
valve seat (20), and seat o-ring (21) from the foot valve
housing (22).
8. Remove the o-ring (16) from the pump cylinder (15).
Reassembling the Fluid Section
NOTE: Use Teon tape on all threaded pipe connections.
1. Place a new seat o-ring (21) into the groove in the bottom
of the foot valve housing (22).
2. Inspect the foot valve seat (20) for wear. If one side is
worn, ip the seat to the unused side. If both sides are
worn, install a new seat. Place the new or ipped seat
(worn side down) into the bore at the bottom of the foot
valve housing (22).
3. Place a new foot valve ball (19) onto the foot valve seat
(20). Using a 1/2” extension bar attached to a 1/2” drive
ratchet, insert the end of the extension bar into the square
opening of the foot valve cage (18) and screw the cage
into the foot valve housing (22). Torque the cage to 300
in./lbs. (25 ft./lbs.).
4. Place the wave washer (17) on top of the foot valve cage
(18).
5. Insert a new Teon o-ring (3) into the groove of the foot
valve housing (22). Lubricate the o-ring using oil or grease.
6. After soaking the leather packings in oil (preferably linseed
oil), reassemble the lower packing set (4). Place the set
onto the outlet valve housing (13) with the peak of the “V”
packings pointing down toward the hex on the outlet valve
housing.
7. Inspect the outlet valve seat (11) for wear. If one side is
worn, ip the seat to the unused side. If both sides are
worn, use a new seat. Insert the outlet valve cage (9),
new outlet valve ball (10), new or ipped seat (worn side
away from ball), and a new seal washer (12) into the
displacement rod (6).
8. Clean the threads on the outlet valve housing (13) and
coat the threads with blue Loctite #242. Make sure the
Loctite is only on the threads.
9. Place the lower packing spring (8) onto the outlet valve
housing (13) followed by the spring retainer (7).
10. Screw the displacement rod (6) and the outlet valve
housing (13) together. Tighten in a vise to 900 in./lbs. (75
ft./lbs.).
11. Insert the Teon o-ring (3) into the upper grove of the
motor/pump block.
12. Insert the upper packing set (4) into the motor/pump block
with the peak of the “V” packings pointing up toward the
motor.
NOTE: The packings must be soaked in oil before
installation.
13. Place the upper packing spring (5) into the motor/pump
block with the small tapered end facing up toward the
motor/pump block.
14. Insert the displacement rod (6) up through the upper
packings in the motor/pump block.
15. Align the holes in the displacement rod (6) and the
hydraulic piston rod and insert the connecting pin (2).
Replace the retaining ring (1) over the connecting pin.
16. Thread the short threads of cylinder spacer (14) into the
motor/pump block and tighten with a strap wrench.
17. Thread the short threads of the pump cylinder (15) into the
cylinder spacer (14) and tighten with a strap wrench.
18. Place the o-ring (16) onto the top grove of the pump
cylinder (15).
19. Thread the foot valve housing (22) onto the pump cylinder
(15), tighten with a strap wrench.
NOTE: It is not necessary to over-tighten the foot valve.
O-ring seals perform sealing function without
excessive tightening. Full thread engagement is
sufcient.
Fluid Section Cut-Away
Peaks of upper
packings must
face up.
Torque outlet
valve housing
to 50 ft./lbs.
(68 N/m).
Use blue
Loctite.
Oil cup area
for piston lube
packing
lubricant.
Peaks of lower
packings must
face down.
Lubricate O-ring.
26 © Titan Tool Inc. All rights reserved.
Hydraulic System
Item Part # Description Quantity
1 313-755 Knob decal................................................1
2 862-414 Set screw ..................................................1
3 448-243 Pressure control knob...............................1
4 860-520 Set screw ..................................................1
5 449-195 Pulley/fan assembly..................................1
6 448-494 Key, pump (.156 x .156 x 13/16) ..............1
7 449-752 Hydraulic pump .........................................1
8 431-042 Tube connector.........................................1
9 858-636 Screw, HH ................................................8
10 858-002 Lock washer ...........................................10
11 325-031 O-ring ........................................................1
12 451-115 Return hose assembly ..............................1
13 451-029 Fitting ........................................................1
14 449-616 Tank cover ................................................1
15 858-609 Clinch nut ..................................................1
16 858-621 Socket screw ............................................2
17 859-001 Washer .....................................................2
18 858-624 Screw ........................................................2
19 449-605 Tank gasket ..............................................1
20 0528171 Nipple .......................................................1
21 472-500 Elbow, street .............................................1
22 448-208 Inlet screen ...............................................1
23 449-718 Hydraulic tank ...........................................1
24 862-411 Flex lock nut .............................................2
25 862-001 Flat washer ...............................................6
26 862-002 Lock washer .............................................4
27 449-212 Plug ..........................................................1
28 862-493 Screw, HH ................................................2
29 862-496 Tap bolt .....................................................1
30 449-282 Shield, gas model .....................................1
449-285 Sheild, electric model
31 192-228 Elbow ........................................................1
32 449-126 Hose clamp ...............................................1
33 420-250 Tubing, Teon...........................................1
34 451-114 Pressure hose assembly ..........................1
35 192-051 Elbow ........................................................1
36 101-205 Ground lug ................................................1
37 451-220 Hydraulic lter ...........................................1
38 449-609 Hydraulic by-pass .....................................1
39 449-626 Hydraulic uid cap/dipstick .......................1
40 449-614 Tube assembly .........................................1
41 862-438 Thumb screw ............................................1
42 862-402 Acorn nut ..................................................1
43 449-107 Mounting plate retainer .............................1
44 449-135 Spacer ......................................................1
45 862-480 Screw, HH ................................................1
46 451-121 Elbow (not shown) ....................................1
47 941-555 Ball valve (not shown) ..............................1
Torque and Sealant Guide
Item Description
4 Use blue Loctite on threads
4 Torque to 10 ft./lbs. (13.5 N/m)
8 Use hydraulic sealant
9 Torque to 20 FT/LBS (28 N/m)
13 Use hydraulic sealant
16 Use blue Loctite on threads
16 Torque to 8 FT/LBS (11 N/m)
18 Torque to 8 FT/LBS (11 N/m)
20 Use hydraulic sealant
21 Use hydraulic sealant
22 Use hydraulic sealant
28 Torque to 15 FT/LBS (20,5 N/m)
29 Torque to 15 FT/LBS (20,5 N/m)
45 Torque to 15 FT/LBS (20,5 N/m)
1
2
3
4
6
7
8
9
10
11
17
18
19
20
21
25
23
29
28
25
30
22
24
26
27
13
14
15
16
12
5
31
32
33
34
36
37
38
9
10
41
45
28
24
42
43
44
40
39
35
© Titan Tool Inc. All rights reserved. 27
Gas Convertokit (P/N 506-275) DC — Electric Convertokit (P/N 506-279)
Item Part # Description Quantity
1 860-552 Screw ........................................................4
2 860-004 Flat washer ...............................................8
3 980-331 Engine, gas 4.8 HP...................................1
4 980-307 Key ...........................................................1
5 448-910 Pulley ........................................................1
6 449-219 Mounting plate, gas engine ......................1
7 860-502 Stop nut ....................................................4
8 449-181 Belt, “V” (not shown, not part of assembly)
Item Part # Description Quantity
1 506-259 Cover ........................................................1
2 860-501 Nut stop ....................................................4
3 860-002 Lock washer .............................................4
4 860-004 Flat washer ...............................................8
5 860-535 Screw ........................................................2
6 978-040 Circuit breaker reset .................................1
7 506-260 ON/OFF switch .........................................1
8 978-350 Motor, DC-Electric, 2 HP,
50 / 60 Hz, 115 V ......................................1
9 977-228 Pulley ........................................................1
10 590-068 Handle grip ...............................................1
11 335-017 Handle ......................................................1
12 860-552 Screw ........................................................2
13 459-018 Mount plate ...............................................1
14 506-255 Rectier (not shown) .................................1
15 506-258 Fan (not shown)........................................1
16 449-181 Belt, “V” (not shown) ............................... 1)
4
6
3
1
2
5
7
2
1
2
3
4
5
4
6
7
8
2
3
4
10
13
11
12
4
9
28 © Titan Tool Inc. All rights reserved.
Bleed Valve Assembly (P/N 944-030)Electric Convertokit, 230V (P/N 506-251)
Item Part # Description Quantity
1 944-047 Hex screw .................................................1
2 944-029 Flat washer ...............................................1
3 944-046 Spacer ......................................................1
4 944-034 Valve handle .............................................1
5 944-035 Spring washer...........................................3
6 944-036 Retaining ring ...........................................1
7 944-029 Valve washer ............................................1
8 944-011 Valve stem ................................................1
9 944-038 Stem o-ring ...............................................1
10 944-031 Valve housing ...........................................1
11 944-039 Ball ............................................................1
12 944-043 Valve seat .................................................1
13 944-044 Valve seal .................................................1
14 944-013 Valve seat retainer....................................1
Item Part # Description Quantity
1 860-501 Stop nut ....................................................6
2 860-002 Lock washer .............................................6
3 860-004 Flat washer .............................................12
4 978-365 Motor, electric, 3 HP, 50 Hz, 230 V ..........1
5 449-152 Pulley ........................................................1
6 449-121 Mounting plate, elec. motor, 3 HP ............1
7 860-552 Screw, HH ................................................4
8 590-411 Spacer ......................................................4
9 860-544 Screw, HH ................................................2
10 590-068 Handle grip ...............................................1
11 335-016 Handle ......................................................1
12 449-181 Belt, “V”
(not shown, not part of assembly)
1
2
3
4
6
7
5
8
9
10
11
12
13
14
5
6
7
3
3
4
1
2
8
3
2
1
9
10
3
11
© Titan Tool Inc. All rights reserved. 29
Filter Assembly
Item Part # Description Quantity
1 930-937 Filter cap assembly ...................................1
2 930-020 Spring .......................................................1
3 930-005 Filter element, 5 M, w/ball .........................1
930-006 Filter element, 50 M, w/ball
930-007 Filter element, 100 M, w/ball
4 920-006 Gasket, Teon (thick) ...............................1
5 920-070 Gasket, Teon (thin) .................................1
6 891-193 O-ring, Teon ............................................1
7 180-909 Seat, tungsten carbide..............................1
8 227-027 Pipe plug...................................................1
9 930-920 Filter body .................................................1
10 227-033 Pipe plug...................................................2
11 808-550 Hex tting, 3/8” .........................................1
12 810-555 Elbow, 90º ................................................1
13 944-030 Bleed valve ...............................................1
14 703-137 Swivel tting assembly .............................1
930-050 Filter service kit
(includes items 2, 4, 5, and 6)
Filter Assembly Specications
Maximum Working Pressure ......... 5000 psi (34.5 MPa)
Filter Area ...................................... 18 In
2
(116 cm
2
)
Outlet Ports.................................... (1) 1/4” NPT(F) for bleed valve
(1) 3/8” NPT(F) with 3/8
NPSM(M) hose connection
(1) 3/8” NPT(F) plugged for
additional gun hookup
Wetted Parts .................................. Carbon steel with electroless
nickel plating, stainless steel,
tungsten carbide, Teon
Item Part # Description Quantity
1 945-600 Heavy duty bleed valve assembly ............1
2 538-031 Hose assembly .........................................1
3 201-555 Elbow ........................................................1
4 103-317 Tube .........................................................1
5 103-106 Heavy duty bleed line assembly
Item Part # Description Quantity
1 945-022 Valve body ................................................1
2 891-073 O-ring, Teon ............................................1
3 945-023 Valve stem ................................................1
4 970-011 Lock nut ....................................................1
5 945-005 Knob ........................................................1
6 945-906 Valve seat .................................................1
7 138-226 Ball, T.C. ...................................................1
8 945-026 Valve stem stop ........................................1
9 891-183 O-ring, Teon ............................................1
1
2
3
12
13
14
4
5
6
7
9
8
10
11
10
Heavy Duty Outlet Assembly
(optional, P/N 448-615)
Heavy Duty Bleed Valve Assembly
(optional, P/N 945-600)
1
2
3
4
1
3
2
4
5
6
7
8
9
30 © Titan Tool Inc. All rights reserved.
Gun Manifold Assemblies (Optional)
SIngle Gun Add-On Manifold Assemblies
SIngle Gun Add-On Manifold Assemblies
1-Gun Add-On Kit
Add-A-Gun Kit
4
5
1
6
3
2
1
2
3
3 Gun Manifold Assembly
975-111 975-311 975-200 975-300
1 Gun Add-On 1 Gun Add-On Add-A-Gun Kit Add-A-Gun kit
Item Part # Description 1/4” 3/8” 1/4” 3/8”
1 814-002 Nipple, Hex ....................................................1 ........................................................1
814-004 Nipple, Hex ................................................................................ 1 ....................................................... 1
2 940-553 Valve, Ball ......................................................1 ........................................................1
941-555 Valve, Ball .................................................................................. 1 ....................................................... 1
3 227-006 Nipple, Hex ....................................................1 ........................................................1
808-555 Nipple, Hex ................................................................................ 1 ....................................................... 1
4 227-033 Plug, Pipe ................................................................................................................1 .......................... 1
5 970-100 Block, Manifold ........................................................................................................1 .......................... 1
6 814-004 Nipple, Hex ..............................................................................................................1 .......................... 1
975-212 975-213 975-214 975-312 975-313 975-314
2 Gun 3 Gun 4 Gun 2 Gun 3 Gun 4 Gun
Part # Description 1/4” 1/4” 1/4” 3/8” 3/8” 3/8”
975-111 1 Gun Add-On, 1/4” .............. 1 ...................... 1 ...................... 1
975-311 1 Gun Add-On, 3/8” ..........................................................................................1 ...................... 1 .......................1
975-200 Add-A-Gun Kit, 1/4” .............. 1 ...................... 2 ...................... 3
975-300 Add-A-Gun Kit, 3/8” ..........................................................................................1 ...................... 2 .......................3
© Titan Tool Inc. All rights reserved. 31
SAE O-Ring Fitting Installation
Steps 1 & 2:
Step 3:
Step 4:
Step 5:
Cautions:
Lubricate
Lubricate
Tighten nut
Recess
gap
No gap
Align
Hold
this part
stationay
Avoid screwing fitting in too far.
Avoid leaving fitting too far out.
Bent washer allows
for o-ring extrusion
O-ring cut on
thread
1. Pull washer and
o-ring back as far as
possible.
2. Lubricate o-ring and
entrance port.
3. Screw tting in until
washer pushes o-ring
into entrance and sits
at against port. (Do
not tighten! - only do
this step hand tight to
compress o-ring into
port!)
4. Back tting out
no more than one
complete turn to align
as required.
5. Torque nut wrench
tight holding backup
on tting. This should
expose a recess
gap behind the nut
which can act as an
indicator that the
tting is assembled
correctly. (This is a
feature for a specic
version of this tting
only - which screws
into the cylinder head.
Other ttings, as the
ones which attach to
the hydraulic pump,
assemble the same
but may not have the
indicator.)
Accessories and Service Kits
These items may be purchased separately from your local Titan
distributor.
Part # Description
103-830 5 Gal. Siphon Hose Assembly w/Rock Catcher
1” x 4.5’
103-808 55 Gal. Siphon Hose Assembly w/Rock Catcher
1” x 6.5’
103-627 Rock Catcher
930-004 Paint Filter Element, 0 Mesh (for mastics)
930-005 Paint Filter Element, 5 Mesh (for multicolors
and heavy materials)
930-006 Paint Filter Element, 50 Mesh (for latex and
normal architectural materials)
930-007 Paint Filter Elements, 100 Mesh (for stains,
lacquers and ne materials)
550-100 S-5 Gun w/Tip
550-110 S-5 Gun, Tip, and 1/4” Hose Kit
101-208 Grounding Clamp
101-212 Grounding Wire, 12 Gauge x 25’
314-480 Piston Lube, 8 oz.
314-482 Liquid Shield Plus, 1 quart
430-362 Coolo™ Hydraulic Fluid, 1 quart
430-361 Coolo™ Hydraulic Fluid, 1 gallon
975-212 2-Gun Manifold with Ball Valves, 1/4”
975-213 3-Gun Manifold with Ball Valves, 1/4”
975-312 2-Gun Manifold with Ball Valves, 3/8”
975-313 3-Gun Manifold with Ball Valves, 3/8”
808-550 3/8” NPS(M) x 3” hex tting
Airless Tip Selection
Tips are selected by the orice size and fan width. The proper
selection is determined by the fan width required for a specic job
and by the orice size that will supply the desired amount of uid
and accomplish proper atomization.
For light viscosity uids, smaller orice tips generally are desired.
For heavier viscosity materials, larger orice tips are preferred.
Please refer to the chart below.
NOTE: Do not exceed the pump’s recommended tip size.
The following chart indicates the most common sizes and the
appropriate materials to be sprayed.
Tip Size Spray Material Filter Type
.011 – .013 Laquers and stains 100 mesh filter
.015 – .019 Oil and latex 50 mesh filter
.021 – .026 Heavy bodied latex and blockfillers 5 mesh filter
Fan widths measuring 8” to 12” (20 to 30 cm) are most preferred
because they offer more control while spraying and are less likely
to plug.
32 © Titan Tool Inc. All rights reserved.
United States Sales & Service
1770 Fernbrook Lane
Plymouth, MN 55447
www.titantool.com
Phone:
Fax:
1-800-526-5362
1-800-528-4826
Fax: 1-763-519-3509
1770 Fernbrook Lane
Plymouth, MN 55447
International Sales
Warranty
Titan Tool, Inc., (“Titan”) warrants that at the time of delivery to the original purchaser for use (“End User”), the equipment covered
by this warranty is free from defects in material and workmanship. With the exception of any special, limited, or extended warranty
published by Titan, Titan’s obligation under this warranty is limited to replacing or repairing without charge those parts which, to Titan’s
reasonable satisfaction, are shown to be defective within twelve (12) months after sale to the End User. This warranty applies only
when the unit is installed and operated in accordance with the recommendations and instructions of Titan.
This warranty does not apply in the case of damage or wear caused by abrasion, corrosion or misuse, negligence, accident, faulty
installation, substitution of non-Titan component parts, or tampering with the unit in a manner to impair normal operation.
Defective parts are to be returned to an authorized Titan sales/service outlet. All transportation charges, including return to the
factory, if necessary, are to be borne and prepaid by the End User. Repaired or replaced equipment will be returned to the End User
transportation prepaid.
THERE IS NO OTHER EXPRESS WARRANTY. TITAN HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING,
BUT NOT LIMITED TO, THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT
PERMITTED BY LAW. THE DURATION OF ANY IMPLIED WARRANTIES WHICH CANNOT BE DISCLAIMED IS LIMITED TO
THE TIME PERIOD SPECIFIED IN THE EXPRESS WARRANTY. IN NO CASE SHALL TITAN LIABILITY EXCEED THE AMOUNT
OF THE PURCHASE PRICE. LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES UNDER ANY AND ALL
WARRANTIES IS EXCLUDED TO THE EXTENT PERMITTED BY LAW.
TITAN MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE WITH RESPECT TO ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY TITAN. THOSE ITEMS SOLD, BUT NOT MANUFACTURED BY TITAN (SUCH AS GAS ENGINES,
SWITCHES, HOSES, ETC.) ARE SUBJECT TO THE WARRANTY, IF ANY, OF THEIR MANUFACTURER. TITAN WILL PROVIDE
THE PURCHASER WITH REASONABLE ASSISTANCE IN MAKING ANY CLAIM FOR BREACH OF THESE WARRANTIES.
Material Safety Data Sheets (MSDS) are available on Titan’s website or by calling Customer Service.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Titan PowrTwin™ 6900 XLT DI El manual del propietario
- Categoría
- Rociador de pintura
- Tipo
- El manual del propietario
- Este manual también es adecuado para
En otros idiomas
Documentos relacionados
-
Titan Impact 410 Manual de usuario
-
-
-
-
Titan PowrTwin™ 6900 XLT El manual del propietario
-
-
-
Titan GPX85 El manual del propietario
-
-
Otros documentos
-
Ryobi RAP200 El manual del propietario
-
Westbrass D49321-62 Guía de instalación
-
Makita SP252-4R El manual del propietario
-
-
-
PowerStroke PSL1PS11 El manual del propietario
-
Sony XR-3300 El manual del propietario
-
Westbrass R93-62 Guía del usuario
-
-
Westbrass 7931817-AF-50 Guía de instalación